All of lore.kernel.org
 help / color / mirror / Atom feed
From: Martin Blumenstingl <martin.blumenstingl-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
To: gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org,
	balbi-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	mark.rutland-5wv7dgnIgG8@public.gmane.org,
	devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-amlogic-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
	yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org,
	Martin Blumenstingl
	<martin.blumenstingl-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
Subject: [PATCH usb-next v2 0/3] DWC3 support for Amlogic Meson AXG and GXL SoCs
Date: Sun, 11 Feb 2018 22:15:14 +0100	[thread overview]
Message-ID: <20180211211517.5846-1-martin.blumenstingl@googlemail.com> (raw)

Amlogic Meson AXG and GXL SoCs can use the dwc3-of-simple with little
modifications. These SoCs use:
- a gate clock for the USB components (DWC3, USB PHYs)
- a reset line which is shared across all USB components (DWC3, USB2 and
  USB3 PHYs, OTG detection logic inside the USB3 PHY registers)
- a reset pulse to trigger the reset
- depending on the SoC two or more PHYs (AXG: 1x USB2 and 1x USB3 PHY,
  GXL: 2x USB2 and 1x USB3 PHY)

This extends the dwc3-of-simple so it supports (depending on the
platform) shared and level resets. Additionally it adds new bindings
for the Amlogic Meson AXG and GXL SoCs, along with the documentation
(dt-bindings).

NOTE: for full support on Amlogic Meson GXL SoCs my other series called
"initialize (multiple) PHYs for a HCD" (see [0] for v8 of that series)
is required. However, there is no direct dependency on that series.
Especially since Meson AXG doesn't need it (since it only has one USB2
and one USB3 PHY, which is already supported by the current dwc3 driver,
unlike the 2x USB2 and 1x USB3 PHYs on Meson GXL).
So I believe that this series can still be merged, even if the other
patchset is not ready yet.


changes since v1 at [1]:
- use of_device_is_compatible() instead of struct dwc3_of_simple_params
  as requested by Felipe Balbi (affects PATCH #2 and #3)
- added Rob's Acked-by to the dt-bindings patch
- added Yixun Lan's Tested-by to the whole series as he tested this
  successfully (along with other patches) on the Amlogic Meson AXG SoC


[0] http://lists.infradead.org/pipermail/linux-amlogic/2018-January/006274.html
[1] http://lists.infradead.org/pipermail/linux-amlogic/2018-January/006286.html

Martin Blumenstingl (3):
  dt-bindings: usb: add support for dwc3 controller on Amlogic Meson GX
  usb: dwc3: of-simple: add support for shared and pulsed reset lines
  usb: dwc3: of-simple: add support for the Amlogic Meson GXL and AXG
    SoCs

 .../devicetree/bindings/usb/amlogic,dwc3.txt       | 42 ++++++++++++++++++++++
 drivers/usb/dwc3/dwc3-of-simple.c                  | 31 ++++++++++++----
 2 files changed, 67 insertions(+), 6 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/amlogic,dwc3.txt

-- 
2.16.1

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

WARNING: multiple messages have this Message-ID (diff)
From: martin.blumenstingl@googlemail.com (Martin Blumenstingl)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH usb-next v2 0/3] DWC3 support for Amlogic Meson AXG and GXL SoCs
Date: Sun, 11 Feb 2018 22:15:14 +0100	[thread overview]
Message-ID: <20180211211517.5846-1-martin.blumenstingl@googlemail.com> (raw)

Amlogic Meson AXG and GXL SoCs can use the dwc3-of-simple with little
modifications. These SoCs use:
- a gate clock for the USB components (DWC3, USB PHYs)
- a reset line which is shared across all USB components (DWC3, USB2 and
  USB3 PHYs, OTG detection logic inside the USB3 PHY registers)
- a reset pulse to trigger the reset
- depending on the SoC two or more PHYs (AXG: 1x USB2 and 1x USB3 PHY,
  GXL: 2x USB2 and 1x USB3 PHY)

This extends the dwc3-of-simple so it supports (depending on the
platform) shared and level resets. Additionally it adds new bindings
for the Amlogic Meson AXG and GXL SoCs, along with the documentation
(dt-bindings).

NOTE: for full support on Amlogic Meson GXL SoCs my other series called
"initialize (multiple) PHYs for a HCD" (see [0] for v8 of that series)
is required. However, there is no direct dependency on that series.
Especially since Meson AXG doesn't need it (since it only has one USB2
and one USB3 PHY, which is already supported by the current dwc3 driver,
unlike the 2x USB2 and 1x USB3 PHYs on Meson GXL).
So I believe that this series can still be merged, even if the other
patchset is not ready yet.


changes since v1 at [1]:
- use of_device_is_compatible() instead of struct dwc3_of_simple_params
  as requested by Felipe Balbi (affects PATCH #2 and #3)
- added Rob's Acked-by to the dt-bindings patch
- added Yixun Lan's Tested-by to the whole series as he tested this
  successfully (along with other patches) on the Amlogic Meson AXG SoC


[0] http://lists.infradead.org/pipermail/linux-amlogic/2018-January/006274.html
[1] http://lists.infradead.org/pipermail/linux-amlogic/2018-January/006286.html

Martin Blumenstingl (3):
  dt-bindings: usb: add support for dwc3 controller on Amlogic Meson GX
  usb: dwc3: of-simple: add support for shared and pulsed reset lines
  usb: dwc3: of-simple: add support for the Amlogic Meson GXL and AXG
    SoCs

 .../devicetree/bindings/usb/amlogic,dwc3.txt       | 42 ++++++++++++++++++++++
 drivers/usb/dwc3/dwc3-of-simple.c                  | 31 ++++++++++++----
 2 files changed, 67 insertions(+), 6 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/amlogic,dwc3.txt

-- 
2.16.1

             reply	other threads:[~2018-02-11 21:15 UTC|newest]

Thread overview: 19+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-02-11 21:15 Martin Blumenstingl [this message]
2018-02-11 21:15 ` [PATCH usb-next v2 0/3] DWC3 support for Amlogic Meson AXG and GXL SoCs Martin Blumenstingl
     [not found] ` <20180211211517.5846-1-martin.blumenstingl-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
2018-02-11 21:15   ` [PATCH usb-next v2 1/3] dt-bindings: usb: add support for dwc3 controller on Amlogic Meson GX Martin Blumenstingl
2018-02-11 21:15     ` Martin Blumenstingl
2018-02-11 21:15     ` [usb-next,v2,1/3] " Martin Blumenstingl
2018-02-11 21:15   ` [PATCH usb-next v2 2/3] usb: dwc3: of-simple: add support for shared and pulsed reset lines Martin Blumenstingl
2018-02-11 21:15     ` Martin Blumenstingl
2018-02-11 21:15     ` [usb-next,v2,2/3] " Martin Blumenstingl
2018-02-11 21:15   ` [PATCH usb-next v2 3/3] usb: dwc3: of-simple: add support for the Amlogic Meson GXL and AXG SoCs Martin Blumenstingl
2018-02-11 21:15     ` Martin Blumenstingl
2018-02-11 21:15     ` [usb-next,v2,3/3] " Martin Blumenstingl
2018-02-20 22:39 ` [PATCH usb-next v2 0/3] DWC3 support for Amlogic Meson AXG and GXL SoCs Martin Blumenstingl
2018-02-20 22:39   ` Martin Blumenstingl
2018-03-03 21:50   ` Martin Blumenstingl
2018-03-03 21:50     ` Martin Blumenstingl
2018-03-08  8:49     ` Felipe Balbi
2018-03-08  8:49       ` Felipe Balbi
2018-03-07 13:13 ` Neil Armstrong
2018-03-07 13:13   ` Neil Armstrong

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180211211517.5846-1-martin.blumenstingl@googlemail.com \
    --to=martin.blumenstingl-gm/ye1e23mwn+bqq9rbeug@public.gmane.org \
    --cc=balbi-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
    --cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org \
    --cc=linux-amlogic-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
    --cc=linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
    --cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
    --cc=yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.