* [RFC PATCH] ARM: dts: meson8b-odroidc1: add microSD support
@ 2018-01-25 4:23 Linus Lüssing
2018-01-28 20:33 ` Martin Blumenstingl
0 siblings, 1 reply; 5+ messages in thread
From: Linus Lüssing @ 2018-01-25 4:23 UTC (permalink / raw)
To: linus-amlogic
The Odroid C1 features a microSD slot. This patch adds the necessary
DT bindings to support it.
Signed-off-by: Linus L?ssing <linus.luessing@c0d3.blue>
---
This patch only worked after Martin's attempt to fix the pinctrl issues
for meson8b:
https://patchwork.kernel.org/patch/10181185/
Another note: I was seeing the following error message in dmesg after
writing a 64MB file to the microSD card and right after typing "$ sync":
[ 512.584687] mmcblk0: error -84 sending status command, retrying
[ 512.586985] mmcblk0: timed out sending r/w cmd command, card status 0xd00
[ 512.591756] mmcblk0: status not valid, retrying timeout
However read/write operations seemed unaffected. The file seemed fine
afterwards, even after unmounting, replugging and remounting the microSD
card.
Not sure whether this error message could potentially point to some
error in the changes in here.
arch/arm/boot/dts/meson8b-odroidc1.dts | 58 ++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/meson8b.dtsi | 8 +++++
2 files changed, 66 insertions(+)
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index d5e83051bb54..3a5603d95b70 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -54,6 +54,7 @@
aliases {
serial0 = &uart_AO;
+ mmc0 = &sd_card_slot;
};
memory {
@@ -69,6 +70,37 @@
default-state = "off";
};
};
+
+ tflash_vdd: regulator-tflash_vdd {
+ /*
+ * signal name from schematics: TFLASH_VDD_EN
+ */
+ compatible = "regulator-fixed";
+
+ regulator-name = "TFLASH_VDD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ tf_io: gpio-regulator-tf_io {
+ compatible = "regulator-gpio";
+
+ regulator-name = "TF_IO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ /*
+ * signal name from schematics: TF_3V3N_1V8_EN
+ */
+ gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0
+ 1800000 1>;
+ };
};
&uart_AO {
@@ -100,6 +132,32 @@
status = "okay";
};
+&sdio {
+ status = "okay";
+
+ pinctrl-0 = <&sd_b_pins>;
+ pinctrl-names = "default";
+
+ /* SD card */
+ sd_card_slot: slot at 1 {
+ compatible = "mmc-slot";
+ reg = <1>;
+ status = "okay";
+
+ bus-width = <4>;
+ no-sdio;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+
+ vmmc-supply = <&tflash_vdd>;
+ vqmmc-supply = <&tf_io>;
+ };
+};
+
ðmac {
status = "okay";
diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi
index fa5274aa370b..87687c09ca3f 100644
--- a/arch/arm/boot/dts/meson8b.dtsi
+++ b/arch/arm/boot/dts/meson8b.dtsi
@@ -206,6 +206,14 @@
function = "ethernet";
};
};
+
+ sd_b_pins: sd-b {
+ mux {
+ groups = "sd_d0_b", "sd_d1_b", "sd_d2_b",
+ "sd_d3_b", "sd_clk_b", "sd_cmd_b";
+ function = "sd_b";
+ };
+ };
};
};
--
2.11.0
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [RFC PATCH] ARM: dts: meson8b-odroidc1: add microSD support
2018-01-25 4:23 [RFC PATCH] ARM: dts: meson8b-odroidc1: add microSD support Linus Lüssing
@ 2018-01-28 20:33 ` Martin Blumenstingl
2018-03-12 21:00 ` Martin Blumenstingl
0 siblings, 1 reply; 5+ messages in thread
From: Martin Blumenstingl @ 2018-01-28 20:33 UTC (permalink / raw)
To: linus-amlogic
Hi Linus,
thank you for this patch!
On Thu, Jan 25, 2018 at 5:23 AM, Linus L?ssing <linus.luessing@c0d3.blue> wrote:
> The Odroid C1 features a microSD slot. This patch adds the necessary
> DT bindings to support it.
>
> Signed-off-by: Linus L?ssing <linus.luessing@c0d3.blue>
> ---
> This patch only worked after Martin's attempt to fix the pinctrl issues
> for meson8b:
>
> https://patchwork.kernel.org/patch/10181185/
unfortunately that patch requires more work
> Another note: I was seeing the following error message in dmesg after
> writing a 64MB file to the microSD card and right after typing "$ sync":
>
> [ 512.584687] mmcblk0: error -84 sending status command, retrying
> [ 512.586985] mmcblk0: timed out sending r/w cmd command, card status 0xd00
> [ 512.591756] mmcblk0: status not valid, retrying timeout
>
> However read/write operations seemed unaffected. The file seemed fine
> afterwards, even after unmounting, replugging and remounting the microSD
> card.
>
> Not sure whether this error message could potentially point to some
> error in the changes in here.
these errors may be a problem with the meson-mx-sdio (MMC) driver
can you please show the output of /sys/kernel/debug/mmc0/ios ?
>
> arch/arm/boot/dts/meson8b-odroidc1.dts | 58 ++++++++++++++++++++++++++++++++++
> arch/arm/boot/dts/meson8b.dtsi | 8 +++++
> 2 files changed, 66 insertions(+)
>
> diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
> index d5e83051bb54..3a5603d95b70 100644
> --- a/arch/arm/boot/dts/meson8b-odroidc1.dts
> +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
> @@ -54,6 +54,7 @@
>
> aliases {
> serial0 = &uart_AO;
> + mmc0 = &sd_card_slot;
> };
>
> memory {
> @@ -69,6 +70,37 @@
> default-state = "off";
> };
> };
> +
> + tflash_vdd: regulator-tflash_vdd {
> + /*
> + * signal name from schematics: TFLASH_VDD_EN
> + */
> + compatible = "regulator-fixed";
> +
> + regulator-name = "TFLASH_VDD";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + tf_io: gpio-regulator-tf_io {
> + compatible = "regulator-gpio";
> +
> + regulator-name = "TF_IO";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> +
> + /*
> + * signal name from schematics: TF_3V3N_1V8_EN
> + */
> + gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
> + gpios-states = <0>;
> +
> + states = <3300000 0
> + 1800000 1>;
> + };
> };
>
> &uart_AO {
> @@ -100,6 +132,32 @@
> status = "okay";
> };
>
> +&sdio {
> + status = "okay";
> +
> + pinctrl-0 = <&sd_b_pins>;
> + pinctrl-names = "default";
> +
> + /* SD card */
> + sd_card_slot: slot at 1 {
> + compatible = "mmc-slot";
> + reg = <1>;
> + status = "okay";
> +
> + bus-width = <4>;
> + no-sdio;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + disable-wp;
> +
> + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
> + cd-inverted;
> +
> + vmmc-supply = <&tflash_vdd>;
> + vqmmc-supply = <&tf_io>;
> + };
> +};
> +
> ðmac {
> status = "okay";
>
> diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi
> index fa5274aa370b..87687c09ca3f 100644
> --- a/arch/arm/boot/dts/meson8b.dtsi
> +++ b/arch/arm/boot/dts/meson8b.dtsi
> @@ -206,6 +206,14 @@
> function = "ethernet";
> };
> };
> +
> + sd_b_pins: sd-b {
> + mux {
> + groups = "sd_d0_b", "sd_d1_b", "sd_d2_b",
> + "sd_d3_b", "sd_clk_b", "sd_cmd_b";
> + function = "sd_b";
> + };
> + };
> };
> };
>
> --
> 2.11.0
>
>
> _______________________________________________
> linux-amlogic mailing list
> linux-amlogic at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-amlogic
Regards
Martin
^ permalink raw reply [flat|nested] 5+ messages in thread
* [RFC PATCH] ARM: dts: meson8b-odroidc1: add microSD support
2018-01-28 20:33 ` Martin Blumenstingl
@ 2018-03-12 21:00 ` Martin Blumenstingl
2018-03-17 17:11 ` Linus Lüssing
0 siblings, 1 reply; 5+ messages in thread
From: Martin Blumenstingl @ 2018-03-12 21:00 UTC (permalink / raw)
To: linus-amlogic
Hi Linus,
On Sun, Jan 28, 2018 at 9:33 PM, Martin Blumenstingl
<martin.blumenstingl@googlemail.com> wrote:
> Hi Linus,
>
> thank you for this patch!
>
> On Thu, Jan 25, 2018 at 5:23 AM, Linus L?ssing <linus.luessing@c0d3.blue> wrote:
>> The Odroid C1 features a microSD slot. This patch adds the necessary
>> DT bindings to support it.
>>
>> Signed-off-by: Linus L?ssing <linus.luessing@c0d3.blue>
>> ---
>> This patch only worked after Martin's attempt to fix the pinctrl issues
>> for meson8b:
>>
>> https://patchwork.kernel.org/patch/10181185/
> unfortunately that patch requires more work
the proper fix is now queued for v4.17
>> Another note: I was seeing the following error message in dmesg after
>> writing a 64MB file to the microSD card and right after typing "$ sync":
>>
>> [ 512.584687] mmcblk0: error -84 sending status command, retrying
>> [ 512.586985] mmcblk0: timed out sending r/w cmd command, card status 0xd00
>> [ 512.591756] mmcblk0: status not valid, retrying timeout
>>
>> However read/write operations seemed unaffected. The file seemed fine
>> afterwards, even after unmounting, replugging and remounting the microSD
>> card.
>>
>> Not sure whether this error message could potentially point to some
>> error in the changes in here.
> these errors may be a problem with the meson-mx-sdio (MMC) driver
> can you please show the output of /sys/kernel/debug/mmc0/ios ?
some users on IRC have successfully tested this patch (together with
the two patches from my series which fix the GPIO handling)
can you please re-send this patch so Kevin can queue it for the next
development cycle?
>>
>> arch/arm/boot/dts/meson8b-odroidc1.dts | 58 ++++++++++++++++++++++++++++++++++
>> arch/arm/boot/dts/meson8b.dtsi | 8 +++++
>> 2 files changed, 66 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
>> index d5e83051bb54..3a5603d95b70 100644
>> --- a/arch/arm/boot/dts/meson8b-odroidc1.dts
>> +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
>> @@ -54,6 +54,7 @@
>>
>> aliases {
>> serial0 = &uart_AO;
>> + mmc0 = &sd_card_slot;
>> };
>>
>> memory {
>> @@ -69,6 +70,37 @@
>> default-state = "off";
>> };
>> };
>> +
>> + tflash_vdd: regulator-tflash_vdd {
>> + /*
>> + * signal name from schematics: TFLASH_VDD_EN
>> + */
>> + compatible = "regulator-fixed";
>> +
>> + regulator-name = "TFLASH_VDD";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> +
>> + gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + };
>> +
>> + tf_io: gpio-regulator-tf_io {
>> + compatible = "regulator-gpio";
>> +
>> + regulator-name = "TF_IO";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> +
>> + /*
>> + * signal name from schematics: TF_3V3N_1V8_EN
>> + */
>> + gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
>> + gpios-states = <0>;
>> +
>> + states = <3300000 0
>> + 1800000 1>;
>> + };
>> };
>>
>> &uart_AO {
>> @@ -100,6 +132,32 @@
>> status = "okay";
>> };
>>
>> +&sdio {
>> + status = "okay";
>> +
>> + pinctrl-0 = <&sd_b_pins>;
>> + pinctrl-names = "default";
>> +
>> + /* SD card */
>> + sd_card_slot: slot at 1 {
>> + compatible = "mmc-slot";
>> + reg = <1>;
>> + status = "okay";
>> +
>> + bus-width = <4>;
>> + no-sdio;
>> + cap-mmc-highspeed;
>> + cap-sd-highspeed;
>> + disable-wp;
>> +
>> + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
>> + cd-inverted;
>> +
>> + vmmc-supply = <&tflash_vdd>;
>> + vqmmc-supply = <&tf_io>;
>> + };
>> +};
>> +
>> ðmac {
>> status = "okay";
>>
>> diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi
>> index fa5274aa370b..87687c09ca3f 100644
>> --- a/arch/arm/boot/dts/meson8b.dtsi
>> +++ b/arch/arm/boot/dts/meson8b.dtsi
>> @@ -206,6 +206,14 @@
>> function = "ethernet";
>> };
>> };
>> +
>> + sd_b_pins: sd-b {
>> + mux {
>> + groups = "sd_d0_b", "sd_d1_b", "sd_d2_b",
>> + "sd_d3_b", "sd_clk_b", "sd_cmd_b";
>> + function = "sd_b";
>> + };
>> + };
>> };
>> };
>>
>> --
>> 2.11.0
>>
>>
>> _______________________________________________
>> linux-amlogic mailing list
>> linux-amlogic at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-amlogic
>
>
> Regards
> Martin
Regards
Martin
^ permalink raw reply [flat|nested] 5+ messages in thread
* [RFC PATCH] ARM: dts: meson8b-odroidc1: add microSD support
2018-03-12 21:00 ` Martin Blumenstingl
@ 2018-03-17 17:11 ` Linus Lüssing
2018-03-18 23:00 ` Martin Blumenstingl
0 siblings, 1 reply; 5+ messages in thread
From: Linus Lüssing @ 2018-03-17 17:11 UTC (permalink / raw)
To: linus-amlogic
Hi Martin,
Sorry for the late reply.
On Mon, Mar 12, 2018 at 10:00:17PM +0100, Martin Blumenstingl wrote:
> >> Not sure whether this error message could potentially point to some
> >> error in the changes in here.
> > these errors may be a problem with the meson-mx-sdio (MMC) driver
> > can you please show the output of /sys/kernel/debug/mmc0/ios ?
> some users on IRC have successfully tested this patch (together with
> the two patches from my series which fix the GPIO handling)
> can you please re-send this patch so Kevin can queue it for the next
> development cycle?
Glad to hear! I also just retried it with a 4.16-rc5 kernel and
your latest fixes and microSD still works for me, too :-).
Regarding the error message, I can't reproduce it anymore. With
the 4.16-rc5 kernel I did not see it. Nevertheless, here's the
output of mmc/ios:
-----
$ cat /sys/kernel/debug/mmc0/ios
clock: 50000000 Hz
actual clock: 39843750 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 2 (sd high-speed)
signal voltage: 0 (3.30 V)
driver type: 0 (driver type B)
-----
Out of curiousity, is the "actual clock" supposed to be so
much lower than "clock"?
Anyway, will resend the patch without the "RFC" now.
Regards, Linus
^ permalink raw reply [flat|nested] 5+ messages in thread
* [RFC PATCH] ARM: dts: meson8b-odroidc1: add microSD support
2018-03-17 17:11 ` Linus Lüssing
@ 2018-03-18 23:00 ` Martin Blumenstingl
0 siblings, 0 replies; 5+ messages in thread
From: Martin Blumenstingl @ 2018-03-18 23:00 UTC (permalink / raw)
To: linus-amlogic
Hi Linus,
On Sat, Mar 17, 2018 at 6:11 PM, Linus L?ssing <linus.luessing@c0d3.blue> wrote:
> Hi Martin,
>
> Sorry for the late reply.
>
> On Mon, Mar 12, 2018 at 10:00:17PM +0100, Martin Blumenstingl wrote:
>> >> Not sure whether this error message could potentially point to some
>> >> error in the changes in here.
>> > these errors may be a problem with the meson-mx-sdio (MMC) driver
>> > can you please show the output of /sys/kernel/debug/mmc0/ios ?
>> some users on IRC have successfully tested this patch (together with
>> the two patches from my series which fix the GPIO handling)
>> can you please re-send this patch so Kevin can queue it for the next
>> development cycle?
>
> Glad to hear! I also just retried it with a 4.16-rc5 kernel and
> your latest fixes and microSD still works for me, too :-).
that's great :-)
> Regarding the error message, I can't reproduce it anymore. With
> the 4.16-rc5 kernel I did not see it. Nevertheless, here's the
> output of mmc/ios:
>
> -----
> $ cat /sys/kernel/debug/mmc0/ios
> clock: 50000000 Hz
> actual clock: 39843750 Hz
> vdd: 21 (3.3 ~ 3.4 V)
> bus mode: 2 (push-pull)
> chip select: 0 (don't care)
> power mode: 2 (on)
> bus width: 2 (4 bits)
> timing spec: 2 (sd high-speed)
> signal voltage: 0 (3.30 V)
> driver type: 0 (driver type B)
> -----
thank you!
not sure why you got an error before, let's hope it won't happen again
> Out of curiousity, is the "actual clock" supposed to be so
> much lower than "clock"?
short answer: yes
long answer: ideally "clock" and "actual clock" should be identical.
however, due to the clock setup for the "SDIO" controller we can't get
much closer because there's no "fractional" divider and we can't
change the rate of the top-most clock (see
/sys/kernel/debug/clk/clk_summary). there is a second MMC controller
in the Meson8b SoCs (which also supports 8-bit bus width, typically
used for eMMC) which can generate better frequencies. the other
controller however is not supported (by the mainline kernel) yet
> Anyway, will resend the patch without the "RFC" now.
thank you, I'll send a Tested-by once I have time to run it on my Odroid-C1
Regards
Martin
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2018-03-18 23:00 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-01-25 4:23 [RFC PATCH] ARM: dts: meson8b-odroidc1: add microSD support Linus Lüssing
2018-01-28 20:33 ` Martin Blumenstingl
2018-03-12 21:00 ` Martin Blumenstingl
2018-03-17 17:11 ` Linus Lüssing
2018-03-18 23:00 ` Martin Blumenstingl
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.