[U-Boot] [PATCH v3 0/3] fix apalis_t30 optional pcie operation

[U-Boot] [PATCH v3 0/3] fix apalis_t30 optional pcie operation

[Marcel Ziswiler]

This series addresses a PCIe reliability issue as observed on Apalis T30
related to a PCIe reset timing violation.

This series is available at http://git.toradex.com/cgit/u-boot-toradex.git/log/?h=for-next

Changes in v3:
- Updated copyright period to 2014-2018.
- Added a blank line after declarations as warned by patman.
- Added Stephen's acked-by.
- Rebased and resend as series so far never got applied!

Changes in v2:
- Leave resp. enable all port 0 pins input drivers as a customer may
  optionally want to use some of those MXM3 pins as inputs as well.
- Stick to struct tegra_pcie_port as suggested by Stephen.
- Introduce proper CONFIG_APALIS_T30_PCIE_EVALBOARD_INIT Kconfig option
  as suggested by Stephen.
- Improved the ifdef vs. if curly braces sequencing as suggested by
  Stephen.
- Keep PCIe port reset status in order to safeguard for future changes
  to the port reset order or even allow for re-initialisation should
  that ever be implemented in the higher levels of the driver model.

Marcel Ziswiler (3):
  apalis_t30: describe pcie ports
  apalis_t30: fix pcie port 0 and 1 pin muxing
  apalis_t30: fix optional pcie port reset for reliable pcie operation

 arch/arm/dts/tegra30-apalis.dts                    |  3 ++
 board/toradex/apalis_t30/Kconfig                   |  9 ++++
 board/toradex/apalis_t30/apalis_t30.c              | 57 +++++++++++++++++++++-
 .../toradex/apalis_t30/pinmux-config-apalis_t30.h  | 16 +++---
 4 files changed, 77 insertions(+), 8 deletions(-)

-- 
2.14.3

[U-Boot] [PATCH v3 1/3] apalis_t30: describe pcie ports

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Add some more comments describing the various PCIe ports available.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v3: None
Changes in v2: None

 arch/arm/dts/tegra30-apalis.dts | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/dts/tegra30-apalis.dts b/arch/arm/dts/tegra30-apalis.dts
index 0b84dae215..0852d8dc53 100644
--- a/arch/arm/dts/tegra30-apalis.dts
+++ b/arch/arm/dts/tegra30-apalis.dts
@@ -43,16 +43,19 @@
 		vddio-pex-ctl-supply = <&sys_3v3_reg>;
 		hvdd-pex-supply = <&sys_3v3_reg>;
 
+		/* Apalis Type Specific 4 Lane PCIe */
 		pci at 1,0 {
 			/* TS_DIFF1/2/3/4 left disabled */
 			nvidia,num-lanes = <4>;
 		};
 
+		/* Apalis PCIe */
 		pci at 2,0 {
 			/* PCIE1_RX/TX left disabled */
 			nvidia,num-lanes = <1>;
 		};
 
+		/* I210 Gigabit Ethernet Controller (On-module) */
 		pci at 3,0 {
 			status = "okay";
 			nvidia,num-lanes = <1>;
-- 
2.14.3

[U-Boot] [PATCH v3 2/3] apalis_t30: fix pcie port 0 and 1 pin muxing

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Fix optional Apalis type specific 4 lane PCIe port 0 and Apalis PCIe
port 1 pin muxing.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v3: None
Changes in v2:
- Leave resp. enable all port 0 pins input drivers as a customer may
  optionally want to use some of those MXM3 pins as inputs as well.

 board/toradex/apalis_t30/pinmux-config-apalis_t30.h | 16 +++++++++-------
 1 file changed, 9 insertions(+), 7 deletions(-)

diff --git a/board/toradex/apalis_t30/pinmux-config-apalis_t30.h b/board/toradex/apalis_t30/pinmux-config-apalis_t30.h
index e0b00ea841..a1e3bb64b6 100644
--- a/board/toradex/apalis_t30/pinmux-config-apalis_t30.h
+++ b/board/toradex/apalis_t30/pinmux-config-apalis_t30.h
@@ -285,17 +285,19 @@ static struct pmux_pingrp_config tegra3_pinmux_common[] = {
 	DEFAULT_PINMUX(SPI1_CS0_N_PX6, SPI1, NORMAL, NORMAL, INPUT),
 	DEFAULT_PINMUX(SPI1_MISO_PX7, SPI1, NORMAL, NORMAL, INPUT),
 
-	DEFAULT_PINMUX(PEX_L0_PRSNT_N_PDD0, PCIE, NORMAL, NORMAL, INPUT),
-	DEFAULT_PINMUX(PEX_L0_RST_N_PDD1, PCIE, NORMAL, NORMAL, OUTPUT),
-	DEFAULT_PINMUX(PEX_L0_CLKREQ_N_PDD2, PCIE, NORMAL, NORMAL, INPUT),
-	DEFAULT_PINMUX(PEX_WAKE_N_PDD3, PCIE, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(PEX_L0_PRSNT_N_PDD0, RSVD2, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(PEX_L0_RST_N_PDD1, RSVD2, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(PEX_L0_CLKREQ_N_PDD2, RSVD2, NORMAL, NORMAL, INPUT),
+
+	DEFAULT_PINMUX(PEX_L1_PRSNT_N_PDD4, RSVD2, DOWN, TRISTATE, OUTPUT), /* NC */
+	DEFAULT_PINMUX(PEX_L1_RST_N_PDD5, RSVD2, DOWN, TRISTATE, OUTPUT), /* NC */
+	DEFAULT_PINMUX(PEX_L1_CLKREQ_N_PDD6, RSVD2, DOWN, TRISTATE, OUTPUT), /* NC */
 
-	DEFAULT_PINMUX(PEX_L1_PRSNT_N_PDD4, PCIE, DOWN, TRISTATE, OUTPUT), /* NC */
-	DEFAULT_PINMUX(PEX_L1_RST_N_PDD5, PCIE, DOWN, TRISTATE, OUTPUT), /* NC */
-	DEFAULT_PINMUX(PEX_L1_CLKREQ_N_PDD6, PCIE, DOWN, TRISTATE, OUTPUT), /* NC */
 	DEFAULT_PINMUX(PEX_L2_PRSNT_N_PDD7, PCIE, NORMAL, NORMAL, INPUT),
 	DEFAULT_PINMUX(PEX_L2_RST_N_PCC6, PCIE, NORMAL, NORMAL, OUTPUT),
 	DEFAULT_PINMUX(PEX_L2_CLKREQ_N_PCC7, PCIE, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(PEX_WAKE_N_PDD3, PCIE, NORMAL, NORMAL, INPUT),
+
 	DEFAULT_PINMUX(HDMI_CEC_PEE3, CEC, NORMAL, NORMAL, INPUT),
 	DEFAULT_PINMUX(HDMI_INT_PN7, RSVD1, NORMAL, NORMAL, INPUT),
 
-- 
2.14.3

[U-Boot] [PATCH v3 3/3] apalis_t30: fix optional pcie port reset for reliable pcie operation

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Allow optionally bringing up the Apalis type specific 4 lane PCIe port
as well as the PCIe switch as found on the Apalis Evaluation board. In
order to avoid violating the PCIe reset timing do this by overriding the
tegra_pcie_board_port_reset() function. Note however that both the
Apalis type specific 4 lane PCIe port as well as the regular Apalis PCIe
port are also left disabled in the device tree by default.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>

---

Changes in v3:
- Updated copyright period to 2014-2018.
- Added a blank line after declarations as warned by patman.
- Added Stephen's acked-by.
- Rebased and resend as series so far never got applied!

Changes in v2:
- Stick to struct tegra_pcie_port as suggested by Stephen.
- Introduce proper CONFIG_APALIS_T30_PCIE_EVALBOARD_INIT Kconfig option
  as suggested by Stephen.
- Improved the ifdef vs. if curly braces sequencing as suggested by
  Stephen.
- Keep PCIe port reset status in order to safeguard for future changes
  to the port reset order or even allow for re-initialisation should
  that ever be implemented in the higher levels of the driver model.

 board/toradex/apalis_t30/Kconfig      |  9 ++++++
 board/toradex/apalis_t30/apalis_t30.c | 57 ++++++++++++++++++++++++++++++++++-
 2 files changed, 65 insertions(+), 1 deletion(-)

diff --git a/board/toradex/apalis_t30/Kconfig b/board/toradex/apalis_t30/Kconfig
index 16224daa12..9cd497091d 100644
--- a/board/toradex/apalis_t30/Kconfig
+++ b/board/toradex/apalis_t30/Kconfig
@@ -25,6 +25,15 @@ config TDX_CFG_BLOCK_PART
 config TDX_CFG_BLOCK_OFFSET
 	default "-512"
 
+config APALIS_T30_PCIE_EVALBOARD_INIT
+	bool "Apalis Evaluation Board PCIe Initialisation"
+	help
+	  Bring up the Apalis type specific 4 lane PCIe port as well as the
+	  Apalis PCIe port with the PCIe switch as found on the Apalis
+	  Evaluation board. Note that by default both those ports are also left
+	  disabled in the device tree which needs changing as well for this to
+	  actually work.
+
 source "board/toradex/common/Kconfig"
 
 endif
diff --git a/board/toradex/apalis_t30/apalis_t30.c b/board/toradex/apalis_t30/apalis_t30.c
index 827eefd463..530ed145b5 100644
--- a/board/toradex/apalis_t30/apalis_t30.c
+++ b/board/toradex/apalis_t30/apalis_t30.c
@@ -1,5 +1,5 @@
 /*
- *  (C) Copyright 2014-2016
+ *  (C) Copyright 2014-2018
  *  Marcel Ziswiler <marcel@ziswiler.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
@@ -14,6 +14,7 @@
 #include <asm/io.h>
 #include <dm.h>
 #include <i2c.h>
+#include <pci_tegra.h>
 #include "../common/tdx-common.h"
 
 #include "pinmux-config-apalis_t30.h"
@@ -23,6 +24,13 @@ DECLARE_GLOBAL_DATA_PTR;
 #define PMU_I2C_ADDRESS		0x2D
 #define MAX_I2C_RETRY		3
 
+#ifdef CONFIG_APALIS_T30_PCIE_EVALBOARD_INIT
+#define PEX_PERST_N	TEGRA_GPIO(S, 7) /* Apalis GPIO7 */
+#define RESET_MOCI_CTRL	TEGRA_GPIO(I, 4)
+
+static int pci_reset_status;
+#endif /* CONFIG_APALIS_T30_PCIE_EVALBOARD_INIT */
+
 int arch_misc_init(void)
 {
 	if (readl(NV_PA_BASE_SRAM + NVBOOTINFOTABLE_BOOTTYPE) ==
@@ -107,6 +115,53 @@ int tegra_pcie_board_init(void)
 		return err;
 	}
 
+#ifdef CONFIG_APALIS_T30_PCIE_EVALBOARD_INIT
+	gpio_request(PEX_PERST_N, "PEX_PERST_N");
+	gpio_request(RESET_MOCI_CTRL, "RESET_MOCI_CTRL");
+#endif /* CONFIG_APALIS_T30_PCIE_EVALBOARD_INIT */
+
 	return 0;
 }
+
+void tegra_pcie_board_port_reset(struct tegra_pcie_port *port)
+{
+	int index = tegra_pcie_port_index_of_port(port);
+
+	if (index == 2) { /* I210 Gigabit Ethernet Controller (On-module) */
+		tegra_pcie_port_reset(port);
+	}
+#ifdef CONFIG_APALIS_T30_PCIE_EVALBOARD_INIT
+	/*
+	 * Apalis PCIe aka port 1 and Apalis Type Specific 4 Lane PCIe aka port
+	 * 0 share the same RESET_MOCI therefore only assert it once for both
+	 * ports to avoid loosing the previously brought up port again.
+	 */
+	else if ((index == 1) || (index == 0)) {
+		/* only do it once per init cycle */
+		if (pci_reset_status % 2 == 0) {
+			/*
+			 * Reset PLX PEX 8605 PCIe Switch plus PCIe devices on
+			 * Apalis Evaluation Board
+			 */
+			gpio_direction_output(PEX_PERST_N, 0);
+			gpio_direction_output(RESET_MOCI_CTRL, 0);
+
+			/*
+			 * Must be asserted for 100 ms after power and clocks
+			 * are stable
+			 */
+			mdelay(100);
+
+			gpio_set_value(PEX_PERST_N, 1);
+			/*
+			 * Err_5: PEX_REFCLK_OUTpx/nx Clock Outputs is not
+			 * Guaranteed Until 900 us After PEX_PERST# De-assertion
+			 */
+			mdelay(1);
+			gpio_set_value(RESET_MOCI_CTRL, 1);
+		}
+		pci_reset_status++;
+	}
+#endif /* CONFIG_APALIS_T30_PCIE_EVALBOARD_INIT */
+}
 #endif /* CONFIG_PCI_TEGRA */
-- 
2.14.3