From: Adam Ford <aford173@gmail.com> To: linux-arm-kernel@lists.infradead.org Cc: Adam Ford <aford173@gmail.com>, devicetree@vger.kernel.org, robh+dt@kernel.org, nsekhar@ti.com Subject: [RFC] ARM: DTS: da850-evm: Refactor device tree layout Date: Thu, 26 Apr 2018 21:35:49 -0500 [thread overview] Message-ID: <20180427023549.13678-1-aford173@gmail.com> (raw) Many of the items in the device tree are already defined or partially defined, so let's remove the redundancies and reduce the whitespace. Signed-off-by: Adam Ford <aford173@gmail.com> diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts index a56d43d53ba1..5bffbe74b6e4 100644 --- a/arch/arm/boot/dts/da850-evm.dts +++ b/arch/arm/boot/dts/da850-evm.dts @@ -27,146 +27,6 @@ spi0 = &spi1; }; - soc@1c00000 { - pmx_core: pinmux@14120 { - status = "okay"; - - mcasp0_pins: pinmux_mcasp0_pins { - pinctrl-single,bits = < - /* - * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR, - * AFSR, AMUTE - */ - 0x00 0x11111111 0xffffffff - /* AXR11, AXR12 */ - 0x04 0x00011000 0x000ff000 - >; - }; - nand_pins: nand_pins { - pinctrl-single,bits = < - /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */ - 0x1c 0x10110110 0xf0ff0ff0 - /* - * EMA_D[0], EMA_D[1], EMA_D[2], - * EMA_D[3], EMA_D[4], EMA_D[5], - * EMA_D[6], EMA_D[7] - */ - 0x24 0x11111111 0xffffffff - /* EMA_A[1], EMA_A[2] */ - 0x30 0x01100000 0x0ff00000 - >; - }; - }; - serial0: serial@42000 { - status = "okay"; - }; - serial1: serial@10c000 { - status = "okay"; - }; - serial2: serial@10d000 { - status = "okay"; - }; - rtc0: rtc@23000 { - status = "okay"; - }; - i2c0: i2c@22000 { - status = "okay"; - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins>; - - tps: tps@48 { - reg = <0x48>; - }; - tlv320aic3106: tlv320aic3106@18 { - #sound-dai-cells = <0>; - compatible = "ti,tlv320aic3106"; - reg = <0x18>; - status = "okay"; - - /* Regulators */ - IOVDD-supply = <&vdcdc2_reg>; - /* Derived from VBAT: Baseboard 3.3V / 1.8V */ - AVDD-supply = <&vbat>; - DRVDD-supply = <&vbat>; - DVDD-supply = <&vbat>; - }; - tca6416: gpio@20 { - compatible = "ti,tca6416"; - reg = <0x20>; - gpio-controller; - #gpio-cells = <2>; - }; - }; - wdt: wdt@21000 { - status = "okay"; - }; - mmc0: mmc@40000 { - max-frequency = <50000000>; - bus-width = <4>; - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>; - cd-gpios = <&gpio 64 GPIO_ACTIVE_LOW>; - wp-gpios = <&gpio 65 GPIO_ACTIVE_HIGH>; - }; - spi1: spi@30e000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&spi1_pins &spi1_cs0_pin>; - flash: m25p80@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "m25p64"; - spi-max-frequency = <30000000>; - m25p,fast-read; - reg = <0>; - partition@0 { - label = "U-Boot-SPL"; - reg = <0x00000000 0x00010000>; - read-only; - }; - partition@1 { - label = "U-Boot"; - reg = <0x00010000 0x00080000>; - read-only; - }; - partition@2 { - label = "U-Boot-Env"; - reg = <0x00090000 0x00010000>; - read-only; - }; - partition@3 { - label = "Kernel"; - reg = <0x000a0000 0x00280000>; - }; - partition@4 { - label = "Filesystem"; - reg = <0x00320000 0x00400000>; - }; - partition@5 { - label = "MAC-Address"; - reg = <0x007f0000 0x00010000>; - read-only; - }; - }; - }; - mdio: mdio@224000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mdio_pins>; - bus_freq = <2200000>; - }; - eth0: ethernet@220000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mii_pins>; - }; - gpio: gpio@226000 { - status = "okay"; - }; - }; - backlight { compatible = "gpio-backlight"; enable-gpios = <&gpio 48 GPIO_ACTIVE_HIGH>; @@ -257,6 +117,142 @@ }; }; + +&pmx_core { + status = "okay"; + + mcasp0_pins: pinmux_mcasp0_pins { + pinctrl-single,bits = < + /* + * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR, + * AFSR, AMUTE + */ + 0x00 0x11111111 0xffffffff + /* AXR11, AXR12 */ + 0x04 0x00011000 0x000ff000 + >; + }; + nand_pins: nand_pins { + pinctrl-single,bits = < + /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */ + 0x1c 0x10110110 0xf0ff0ff0 + /* + * EMA_D[0], EMA_D[1], EMA_D[2], + * EMA_D[3], EMA_D[4], EMA_D[5], + * EMA_D[6], EMA_D[7] + */ + 0x24 0x11111111 0xffffffff + /* EMA_A[1], EMA_A[2] */ + 0x30 0x01100000 0x0ff00000 + >; + }; +}; +&serial0 { + status = "okay"; +}; +&serial1 { + status = "okay"; +}; +&serial2 { + status = "okay"; +}; +&rtc0 { + status = "okay"; +}; +&i2c0 { + status = "okay"; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + tps: tps@48 { + reg = <0x48>; + }; + tlv320aic3106: tlv320aic3106@18 { + #sound-dai-cells = <0>; + compatible = "ti,tlv320aic3106"; + reg = <0x18>; + status = "okay"; + + /* Regulators */ + IOVDD-supply = <&vdcdc2_reg>; + /* Derived from VBAT: Baseboard 3.3V / 1.8V */ + AVDD-supply = <&vbat>; + DRVDD-supply = <&vbat>; + DVDD-supply = <&vbat>; + }; + tca6416: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; +}; +&wdt { + status = "okay"; +}; +&mmc0 { + max-frequency = <50000000>; + bus-width = <4>; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + cd-gpios = <&gpio 64 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio 65 GPIO_ACTIVE_HIGH>; +}; +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins &spi1_cs0_pin>; + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p64"; + spi-max-frequency = <30000000>; + m25p,fast-read; + reg = <0>; + partition@0 { + label = "U-Boot-SPL"; + reg = <0x00000000 0x00010000>; + read-only; + }; + partition@1 { + label = "U-Boot"; + reg = <0x00010000 0x00080000>; + read-only; + }; + partition@2 { + label = "U-Boot-Env"; + reg = <0x00090000 0x00010000>; + read-only; + }; + partition@3 { + label = "Kernel"; + reg = <0x000a0000 0x00280000>; + }; + partition@4 { + label = "Filesystem"; + reg = <0x00320000 0x00400000>; + }; + partition@5 { + label = "MAC-Address"; + reg = <0x007f0000 0x00010000>; + read-only; + }; + }; +}; +&mdio { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + bus_freq = <2200000>; +}; +ð0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mii_pins>; +}; + /include/ "tps6507x.dtsi" &tps { -- 2.17.0
WARNING: multiple messages have this Message-ID (diff)
From: aford173@gmail.com (Adam Ford) To: linux-arm-kernel@lists.infradead.org Subject: [RFC] ARM: DTS: da850-evm: Refactor device tree layout Date: Thu, 26 Apr 2018 21:35:49 -0500 [thread overview] Message-ID: <20180427023549.13678-1-aford173@gmail.com> (raw) Many of the items in the device tree are already defined or partially defined, so let's remove the redundancies and reduce the whitespace. Signed-off-by: Adam Ford <aford173@gmail.com> diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts index a56d43d53ba1..5bffbe74b6e4 100644 --- a/arch/arm/boot/dts/da850-evm.dts +++ b/arch/arm/boot/dts/da850-evm.dts @@ -27,146 +27,6 @@ spi0 = &spi1; }; - soc at 1c00000 { - pmx_core: pinmux at 14120 { - status = "okay"; - - mcasp0_pins: pinmux_mcasp0_pins { - pinctrl-single,bits = < - /* - * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR, - * AFSR, AMUTE - */ - 0x00 0x11111111 0xffffffff - /* AXR11, AXR12 */ - 0x04 0x00011000 0x000ff000 - >; - }; - nand_pins: nand_pins { - pinctrl-single,bits = < - /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */ - 0x1c 0x10110110 0xf0ff0ff0 - /* - * EMA_D[0], EMA_D[1], EMA_D[2], - * EMA_D[3], EMA_D[4], EMA_D[5], - * EMA_D[6], EMA_D[7] - */ - 0x24 0x11111111 0xffffffff - /* EMA_A[1], EMA_A[2] */ - 0x30 0x01100000 0x0ff00000 - >; - }; - }; - serial0: serial at 42000 { - status = "okay"; - }; - serial1: serial at 10c000 { - status = "okay"; - }; - serial2: serial at 10d000 { - status = "okay"; - }; - rtc0: rtc at 23000 { - status = "okay"; - }; - i2c0: i2c at 22000 { - status = "okay"; - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins>; - - tps: tps at 48 { - reg = <0x48>; - }; - tlv320aic3106: tlv320aic3106 at 18 { - #sound-dai-cells = <0>; - compatible = "ti,tlv320aic3106"; - reg = <0x18>; - status = "okay"; - - /* Regulators */ - IOVDD-supply = <&vdcdc2_reg>; - /* Derived from VBAT: Baseboard 3.3V / 1.8V */ - AVDD-supply = <&vbat>; - DRVDD-supply = <&vbat>; - DVDD-supply = <&vbat>; - }; - tca6416: gpio at 20 { - compatible = "ti,tca6416"; - reg = <0x20>; - gpio-controller; - #gpio-cells = <2>; - }; - }; - wdt: wdt at 21000 { - status = "okay"; - }; - mmc0: mmc at 40000 { - max-frequency = <50000000>; - bus-width = <4>; - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>; - cd-gpios = <&gpio 64 GPIO_ACTIVE_LOW>; - wp-gpios = <&gpio 65 GPIO_ACTIVE_HIGH>; - }; - spi1: spi at 30e000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&spi1_pins &spi1_cs0_pin>; - flash: m25p80 at 0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "m25p64"; - spi-max-frequency = <30000000>; - m25p,fast-read; - reg = <0>; - partition at 0 { - label = "U-Boot-SPL"; - reg = <0x00000000 0x00010000>; - read-only; - }; - partition at 1 { - label = "U-Boot"; - reg = <0x00010000 0x00080000>; - read-only; - }; - partition at 2 { - label = "U-Boot-Env"; - reg = <0x00090000 0x00010000>; - read-only; - }; - partition at 3 { - label = "Kernel"; - reg = <0x000a0000 0x00280000>; - }; - partition at 4 { - label = "Filesystem"; - reg = <0x00320000 0x00400000>; - }; - partition at 5 { - label = "MAC-Address"; - reg = <0x007f0000 0x00010000>; - read-only; - }; - }; - }; - mdio: mdio at 224000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mdio_pins>; - bus_freq = <2200000>; - }; - eth0: ethernet at 220000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mii_pins>; - }; - gpio: gpio at 226000 { - status = "okay"; - }; - }; - backlight { compatible = "gpio-backlight"; enable-gpios = <&gpio 48 GPIO_ACTIVE_HIGH>; @@ -257,6 +117,142 @@ }; }; + +&pmx_core { + status = "okay"; + + mcasp0_pins: pinmux_mcasp0_pins { + pinctrl-single,bits = < + /* + * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR, + * AFSR, AMUTE + */ + 0x00 0x11111111 0xffffffff + /* AXR11, AXR12 */ + 0x04 0x00011000 0x000ff000 + >; + }; + nand_pins: nand_pins { + pinctrl-single,bits = < + /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */ + 0x1c 0x10110110 0xf0ff0ff0 + /* + * EMA_D[0], EMA_D[1], EMA_D[2], + * EMA_D[3], EMA_D[4], EMA_D[5], + * EMA_D[6], EMA_D[7] + */ + 0x24 0x11111111 0xffffffff + /* EMA_A[1], EMA_A[2] */ + 0x30 0x01100000 0x0ff00000 + >; + }; +}; +&serial0 { + status = "okay"; +}; +&serial1 { + status = "okay"; +}; +&serial2 { + status = "okay"; +}; +&rtc0 { + status = "okay"; +}; +&i2c0 { + status = "okay"; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + tps: tps at 48 { + reg = <0x48>; + }; + tlv320aic3106: tlv320aic3106 at 18 { + #sound-dai-cells = <0>; + compatible = "ti,tlv320aic3106"; + reg = <0x18>; + status = "okay"; + + /* Regulators */ + IOVDD-supply = <&vdcdc2_reg>; + /* Derived from VBAT: Baseboard 3.3V / 1.8V */ + AVDD-supply = <&vbat>; + DRVDD-supply = <&vbat>; + DVDD-supply = <&vbat>; + }; + tca6416: gpio at 20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; +}; +&wdt { + status = "okay"; +}; +&mmc0 { + max-frequency = <50000000>; + bus-width = <4>; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + cd-gpios = <&gpio 64 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio 65 GPIO_ACTIVE_HIGH>; +}; +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins &spi1_cs0_pin>; + flash: m25p80 at 0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p64"; + spi-max-frequency = <30000000>; + m25p,fast-read; + reg = <0>; + partition at 0 { + label = "U-Boot-SPL"; + reg = <0x00000000 0x00010000>; + read-only; + }; + partition at 1 { + label = "U-Boot"; + reg = <0x00010000 0x00080000>; + read-only; + }; + partition at 2 { + label = "U-Boot-Env"; + reg = <0x00090000 0x00010000>; + read-only; + }; + partition at 3 { + label = "Kernel"; + reg = <0x000a0000 0x00280000>; + }; + partition at 4 { + label = "Filesystem"; + reg = <0x00320000 0x00400000>; + }; + partition at 5 { + label = "MAC-Address"; + reg = <0x007f0000 0x00010000>; + read-only; + }; + }; +}; +&mdio { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + bus_freq = <2200000>; +}; +ð0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mii_pins>; +}; + /include/ "tps6507x.dtsi" &tps { -- 2.17.0
next reply other threads:[~2018-04-27 2:35 UTC|newest] Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top 2018-04-27 2:35 Adam Ford [this message] 2018-04-27 2:35 ` [RFC] ARM: DTS: da850-evm: Refactor device tree layout Adam Ford 2018-04-27 4:57 ` Sekhar Nori 2018-04-27 4:57 ` Sekhar Nori
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20180427023549.13678-1-aford173@gmail.com \ --to=aford173@gmail.com \ --cc=devicetree@vger.kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=nsekhar@ti.com \ --cc=robh+dt@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.