enable OTG on wandboard and riotboard

enable OTG on wandboard and riotboard

[Alexander Kurz]

Both boards wandboard and riotboard feature an USB OTG connector.
Change the DT regulator nodes to match the convention, fix the
GPIO regulator polatity for the riotboard and add enable OTG
including the regulator infrastructure on the riotboard. 

Changes since v2:
* split patch 0001 into two board specific patches
* use GPIO_ACTIVE_HIGH instead of literal numbers in patch v1-0001 (now v2-0002) 

enable OTG on wandboard and riotboard

[Alexander Kurz]

Both boards wandboard and riotboard feature an USB OTG connector.
Change the DT regulator nodes to match the convention, fix the
GPIO regulator polatity for the riotboard and add enable OTG
including the regulator infrastructure on the riotboard. 

Changes since v2:
* split patch 0001 into two board specific patches
* use GPIO_ACTIVE_HIGH instead of literal numbers in patch v1-0001 (now v2-0002) 

[PATCH v2 1/4] ARM: dts: imx6qdl-wandboard: remove regulators bus node

[Alexander Kurz]

To match the convention, move all regulator-fixed nodes directly into
the root node.

Signed-off-by: Alexander Kurz <akurz@blala.de>
---
 arch/arm/boot/dts/imx6qdl-wandboard.dtsi | 40 +++++++++++++-------------------
 1 file changed, 16 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
index ed96d7b5feab..b9c6c9d5d357 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
@@ -12,30 +12,6 @@
 #include <dt-bindings/gpio/gpio.h>
 
 / {
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_2p5v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
-
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-	};
-
 	sound {
 		compatible = "fsl,imx6-wandboard-sgtl5000",
 			     "fsl,imx-audio-sgtl5000";
@@ -56,6 +32,22 @@
 		spdif-controller = <&spdif>;
 		spdif-out;
 	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 };
 
 &audmux {
-- 
2.11.0

[PATCH v2 1/4] ARM: dts: imx6qdl-wandboard: remove regulators bus node

[Alexander Kurz]

To match the convention, move all regulator-fixed nodes directly into
the root node.

Signed-off-by: Alexander Kurz <akurz@blala.de>
---
 arch/arm/boot/dts/imx6qdl-wandboard.dtsi | 40 +++++++++++++-------------------
 1 file changed, 16 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
index ed96d7b5feab..b9c6c9d5d357 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
@@ -12,30 +12,6 @@
 #include <dt-bindings/gpio/gpio.h>
 
 / {
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_2p5v: regulator at 0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
-
-		reg_3p3v: regulator at 1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-	};
-
 	sound {
 		compatible = "fsl,imx6-wandboard-sgtl5000",
 			     "fsl,imx-audio-sgtl5000";
@@ -56,6 +32,22 @@
 		spdif-controller = <&spdif>;
 		spdif-out;
 	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 };
 
 &audmux {
-- 
2.11.0

[PATCH v2 2/4] ARM: dts: imx6dl-riotboard: remove regulators bus node

[Alexander Kurz]

To match the convention, move regulator-fixed nodes directly into
the root node.

Signed-off-by: Alexander Kurz <akurz@blala.de>
---
 arch/arm/boot/dts/imx6dl-riotboard.dts | 55 ++++++++++++++--------------------
 1 file changed, 23 insertions(+), 32 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
index 2e98c92adff7..a6851bfebbdb 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
@@ -19,38 +19,6 @@
 		reg = <0x10000000 0x40000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_2p5v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-		};
-
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
-
-		reg_usb_otg_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 0>;
-			enable-active-high;
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -82,6 +50,29 @@
 			mux-int-port = <1>;
 			mux-ext-port = <3>;
 	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb_otg_vbus: regulator-usbotgvbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &audmux {
-- 
2.11.0

[PATCH v2 2/4] ARM: dts: imx6dl-riotboard: remove regulators bus node

[Alexander Kurz]

To match the convention, move regulator-fixed nodes directly into
the root node.

Signed-off-by: Alexander Kurz <akurz@blala.de>
---
 arch/arm/boot/dts/imx6dl-riotboard.dts | 55 ++++++++++++++--------------------
 1 file changed, 23 insertions(+), 32 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
index 2e98c92adff7..a6851bfebbdb 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
@@ -19,38 +19,6 @@
 		reg = <0x10000000 0x40000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_2p5v: regulator at 0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-		};
-
-		reg_3p3v: regulator at 1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
-
-		reg_usb_otg_vbus: regulator at 2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 0>;
-			enable-active-high;
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -82,6 +50,29 @@
 			mux-int-port = <1>;
 			mux-ext-port = <3>;
 	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb_otg_vbus: regulator-usbotgvbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &audmux {
-- 
2.11.0

[PATCH v2 3/4] ARM: dts: imx6qdl-wandboard: enable USB OTG

[Alexander Kurz]

Enable USB OTG (dual-role) on the Wandboard.
Note, that the USB_OTG_VBUS current is quite limited due to a 22R resistor
in the power line. Hence, the overcurrent signal of 1A will never be
triggered on this board.

Signed-off-by: Alexander Kurz <akurz@blala.de>
---
 arch/arm/boot/dts/imx6qdl-wandboard.dtsi | 19 ++++++++++++++++++-
 1 file changed, 18 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
index b9c6c9d5d357..01ee36af7ba4 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
@@ -48,6 +48,16 @@
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
 	};
+
+	reg_usb_otg_vbus: regulator-usbotgvbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotgvbus>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
+	};
 };
 
 &audmux {
@@ -162,6 +172,12 @@
 			>;
 		};
 
+		pinctrl_usbotgvbus: usbotgvbusgrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x130b0
+			>;
+		};
+
 		pinctrl_usdhc1: usdhc1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD1_CMD__SD1_CMD		0x17059
@@ -236,10 +252,11 @@
 };
 
 &usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg>;
 	disable-over-current;
-	dr_mode = "peripheral";
+	dr_mode = "otg";
 	status = "okay";
 };
 
-- 
2.11.0

[PATCH v2 3/4] ARM: dts: imx6qdl-wandboard: enable USB OTG

[Alexander Kurz]

Enable USB OTG (dual-role) on the Wandboard.
Note, that the USB_OTG_VBUS current is quite limited due to a 22R resistor
in the power line. Hence, the overcurrent signal of 1A will never be
triggered on this board.

Signed-off-by: Alexander Kurz <akurz@blala.de>
---
 arch/arm/boot/dts/imx6qdl-wandboard.dtsi | 19 ++++++++++++++++++-
 1 file changed, 18 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
index b9c6c9d5d357..01ee36af7ba4 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
@@ -48,6 +48,16 @@
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
 	};
+
+	reg_usb_otg_vbus: regulator-usbotgvbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotgvbus>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
+	};
 };
 
 &audmux {
@@ -162,6 +172,12 @@
 			>;
 		};
 
+		pinctrl_usbotgvbus: usbotgvbusgrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x130b0
+			>;
+		};
+
 		pinctrl_usdhc1: usdhc1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD1_CMD__SD1_CMD		0x17059
@@ -236,10 +252,11 @@
 };
 
 &usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg>;
 	disable-over-current;
-	dr_mode = "peripheral";
+	dr_mode = "otg";
 	status = "okay";
 };
 
-- 
2.11.0

[PATCH v2 4/4] ARM: dts: imx6dl-riotboard: fix OTG regulator polarity

[Alexander Kurz]

USB OTG power is switched on when the GPIO is pulled low.

Signed-off-by: Alexander Kurz <akurz@blala.de>
---
 arch/arm/boot/dts/imx6dl-riotboard.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
index a6851bfebbdb..89b06e20480d 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
@@ -70,8 +70,7 @@
 		regulator-name = "usb_otg_vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
 	};
 };
 
-- 
2.11.0

[PATCH v2 4/4] ARM: dts: imx6dl-riotboard: fix OTG regulator polarity

[Alexander Kurz]

USB OTG power is switched on when the GPIO is pulled low.

Signed-off-by: Alexander Kurz <akurz@blala.de>
---
 arch/arm/boot/dts/imx6dl-riotboard.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
index a6851bfebbdb..89b06e20480d 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
@@ -70,8 +70,7 @@
 		regulator-name = "usb_otg_vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
 	};
 };
 
-- 
2.11.0

Re: [PATCH v2 1/4] ARM: dts: imx6qdl-wandboard: remove regulators bus node

[Fabio Estevam]

On Tue, May 29, 2018 at 3:20 AM, Alexander Kurz <akurz@blala.de> wrote:
> To match the convention, move all regulator-fixed nodes directly into
> the root node.
>
> Signed-off-by: Alexander Kurz <akurz@blala.de>

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

[PATCH v2 1/4] ARM: dts: imx6qdl-wandboard: remove regulators bus node

[Fabio Estevam]

On Tue, May 29, 2018 at 3:20 AM, Alexander Kurz <akurz@blala.de> wrote:
> To match the convention, move all regulator-fixed nodes directly into
> the root node.
>
> Signed-off-by: Alexander Kurz <akurz@blala.de>

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

Re: [PATCH v2 2/4] ARM: dts: imx6dl-riotboard: remove regulators bus node

[Fabio Estevam]

On Tue, May 29, 2018 at 3:20 AM, Alexander Kurz <akurz@blala.de> wrote:
> To match the convention, move regulator-fixed nodes directly into
> the root node.
>
> Signed-off-by: Alexander Kurz <akurz@blala.de>

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

[PATCH v2 2/4] ARM: dts: imx6dl-riotboard: remove regulators bus node

[Fabio Estevam]

On Tue, May 29, 2018 at 3:20 AM, Alexander Kurz <akurz@blala.de> wrote:
> To match the convention, move regulator-fixed nodes directly into
> the root node.
>
> Signed-off-by: Alexander Kurz <akurz@blala.de>

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

Re: [PATCH v2 3/4] ARM: dts: imx6qdl-wandboard: enable USB OTG

[Fabio Estevam]

On Tue, May 29, 2018 at 3:20 AM, Alexander Kurz <akurz@blala.de> wrote:
> Enable USB OTG (dual-role) on the Wandboard.
> Note, that the USB_OTG_VBUS current is quite limited due to a 22R resistor
> in the power line. Hence, the overcurrent signal of 1A will never be
> triggered on this board.
>
> Signed-off-by: Alexander Kurz <akurz@blala.de>

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

[PATCH v2 3/4] ARM: dts: imx6qdl-wandboard: enable USB OTG

[Fabio Estevam]

On Tue, May 29, 2018 at 3:20 AM, Alexander Kurz <akurz@blala.de> wrote:
> Enable USB OTG (dual-role) on the Wandboard.
> Note, that the USB_OTG_VBUS current is quite limited due to a 22R resistor
> in the power line. Hence, the overcurrent signal of 1A will never be
> triggered on this board.
>
> Signed-off-by: Alexander Kurz <akurz@blala.de>

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

Re: [PATCH v2 4/4] ARM: dts: imx6dl-riotboard: fix OTG regulator polarity

[Fabio Estevam]

On Tue, May 29, 2018 at 3:20 AM, Alexander Kurz <akurz@blala.de> wrote:
> USB OTG power is switched on when the GPIO is pulled low.
>
> Signed-off-by: Alexander Kurz <akurz@blala.de>
> ---
>  arch/arm/boot/dts/imx6dl-riotboard.dts | 3 +--
>  1 file changed, 1 insertion(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
> index a6851bfebbdb..89b06e20480d 100644
> --- a/arch/arm/boot/dts/imx6dl-riotboard.dts
> +++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
> @@ -70,8 +70,7 @@
>                 regulator-name = "usb_otg_vbus";
>                 regulator-min-microvolt = <5000000>;
>                 regulator-max-microvolt = <5000000>;
> -               gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> -               enable-active-high;
> +               gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

[PATCH v2 4/4] ARM: dts: imx6dl-riotboard: fix OTG regulator polarity

[Fabio Estevam]

On Tue, May 29, 2018 at 3:20 AM, Alexander Kurz <akurz@blala.de> wrote:
> USB OTG power is switched on when the GPIO is pulled low.
>
> Signed-off-by: Alexander Kurz <akurz@blala.de>
> ---
>  arch/arm/boot/dts/imx6dl-riotboard.dts | 3 +--
>  1 file changed, 1 insertion(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
> index a6851bfebbdb..89b06e20480d 100644
> --- a/arch/arm/boot/dts/imx6dl-riotboard.dts
> +++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
> @@ -70,8 +70,7 @@
>                 regulator-name = "usb_otg_vbus";
>                 regulator-min-microvolt = <5000000>;
>                 regulator-max-microvolt = <5000000>;
> -               gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> -               enable-active-high;
> +               gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

Re: [PATCH v2 1/4] ARM: dts: imx6qdl-wandboard: remove regulators bus node

[Shawn Guo]

On Tue, May 29, 2018 at 06:20:18AM +0000, Alexander Kurz wrote:
> To match the convention, move all regulator-fixed nodes directly into
> the root node.
> 
> Signed-off-by: Alexander Kurz <akurz@blala.de>

Applied all, thanks.

[PATCH v2 1/4] ARM: dts: imx6qdl-wandboard: remove regulators bus node

[Shawn Guo]

On Tue, May 29, 2018 at 06:20:18AM +0000, Alexander Kurz wrote:
> To match the convention, move all regulator-fixed nodes directly into
> the root node.
> 
> Signed-off-by: Alexander Kurz <akurz@blala.de>

Applied all, thanks.