All of lore.kernel.org
 help / color / mirror / Atom feed
From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To: wsa@the-dreams.de, robh+dt@kernel.org, afaerber@suse.de
Cc: linus.walleij@linaro.org, linux-i2c@vger.kernel.org,
	liuwei@actions-semi.com, mp-cs@actions-semi.com,
	96boards@ucrobotics.com, devicetree@vger.kernel.org,
	andy.shevchenko@gmail.com, daniel.thompson@linaro.org,
	amit.kucheria@linaro.org, linux-arm-kernel@lists.infradead.org,
	linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org,
	hzhang@ucrobotics.com, bdong@ucrobotics.com,
	manivannanece23@gmail.com, thomas.liau@actions-semi.com,
	jeff.chen@actions-semi.com,
	Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Subject: [PATCH v2 4/6] arm64: dts: actions: Enable I2C1 and I2C2 in Bubblegum-96 board
Date: Thu, 28 Jun 2018 23:40:40 +0530	[thread overview]
Message-ID: <20180628181042.2239-5-manivannan.sadhasivam@linaro.org> (raw)
In-Reply-To: <20180628181042.2239-1-manivannan.sadhasivam@linaro.org>

Enable I2C1 and I2C2 exposed on the low speed expansion connector in
Bubblegum-96 board.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm64/boot/dts/actions/s900-bubblegum-96.dts | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
index d0ba35df9015..57ae374cfb5a 100644
--- a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
+++ b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
@@ -7,6 +7,7 @@
 /dts-v1/;
 
 #include "s900.dtsi"
+#include "s900-bubblegum-96-pins.dtsi"
 
 / {
 	compatible = "ucrobotics,bubblegum-96", "actions,s900";
@@ -35,6 +36,16 @@
 	clocks = <&cmu CLK_UART5>;
 };
 
+&i2c1 {
+	status = "okay";
+	clocks = <&cmu CLK_I2C1>;
+};
+
+&i2c2 {
+	status = "okay";
+	clocks = <&cmu CLK_I2C2>;
+};
+
 /*
  * GPIO name legend: proper name = the GPIO line is used as GPIO
  *         NC = not connected (pin out but not routed from the chip to
-- 
2.17.1

WARNING: multiple messages have this Message-ID (diff)
From: manivannan.sadhasivam@linaro.org (Manivannan Sadhasivam)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 4/6] arm64: dts: actions: Enable I2C1 and I2C2 in Bubblegum-96 board
Date: Thu, 28 Jun 2018 23:40:40 +0530	[thread overview]
Message-ID: <20180628181042.2239-5-manivannan.sadhasivam@linaro.org> (raw)
In-Reply-To: <20180628181042.2239-1-manivannan.sadhasivam@linaro.org>

Enable I2C1 and I2C2 exposed on the low speed expansion connector in
Bubblegum-96 board.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm64/boot/dts/actions/s900-bubblegum-96.dts | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
index d0ba35df9015..57ae374cfb5a 100644
--- a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
+++ b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
@@ -7,6 +7,7 @@
 /dts-v1/;
 
 #include "s900.dtsi"
+#include "s900-bubblegum-96-pins.dtsi"
 
 / {
 	compatible = "ucrobotics,bubblegum-96", "actions,s900";
@@ -35,6 +36,16 @@
 	clocks = <&cmu CLK_UART5>;
 };
 
+&i2c1 {
+	status = "okay";
+	clocks = <&cmu CLK_I2C1>;
+};
+
+&i2c2 {
+	status = "okay";
+	clocks = <&cmu CLK_I2C2>;
+};
+
 /*
  * GPIO name legend: proper name = the GPIO line is used as GPIO
  *         NC = not connected (pin out but not routed from the chip to
-- 
2.17.1

  parent reply	other threads:[~2018-06-28 18:10 UTC|newest]

Thread overview: 38+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-06-28 18:10 [PATCH v2 0/6] Add Actions Semi S900 I2C support Manivannan Sadhasivam
2018-06-28 18:10 ` Manivannan Sadhasivam
2018-06-28 18:10 ` [PATCH v2 1/6] dt-bindings: i2c: Add binding for Actions Semi OWL I2C controller Manivannan Sadhasivam
2018-06-28 18:10   ` Manivannan Sadhasivam
2018-06-30 12:23   ` Andreas Färber
2018-06-30 12:23     ` Andreas Färber
2018-06-30 12:40     ` Manivannan Sadhasivam
2018-06-30 12:40       ` Manivannan Sadhasivam
2018-06-28 18:10 ` [PATCH v2 2/6] arm64: dts: actions: Add Actions Semi S900 I2C controller nodes Manivannan Sadhasivam
2018-06-28 18:10   ` Manivannan Sadhasivam
2018-06-28 18:10 ` [PATCH v2 3/6] arm64: dts: actions: Add pinctrl definition for S900 I2C controller Manivannan Sadhasivam
2018-06-28 18:10   ` Manivannan Sadhasivam
2018-06-28 18:10 ` Manivannan Sadhasivam [this message]
2018-06-28 18:10   ` [PATCH v2 4/6] arm64: dts: actions: Enable I2C1 and I2C2 in Bubblegum-96 board Manivannan Sadhasivam
2018-06-28 18:10 ` [PATCH v2 5/6] i2c: Add Actions Semi OWL family S900 I2C driver Manivannan Sadhasivam
2018-06-28 18:10   ` Manivannan Sadhasivam
2018-06-29  4:45   ` Peter Rosin
2018-06-29  4:45     ` Peter Rosin
2018-06-30  8:13     ` Manivannan Sadhasivam
2018-06-30  8:13       ` Manivannan Sadhasivam
2018-06-30  8:13       ` Manivannan Sadhasivam
2018-06-30 12:14   ` Andy Shevchenko
2018-06-30 12:14     ` Andy Shevchenko
2018-06-30 12:44     ` Manivannan Sadhasivam
2018-06-30 12:44       ` Manivannan Sadhasivam
2018-06-30 13:04       ` Andy Shevchenko
2018-06-30 13:04         ` Andy Shevchenko
2018-06-30 13:04         ` Andy Shevchenko
2018-06-30 13:14         ` Manivannan Sadhasivam
2018-06-30 13:14           ` Manivannan Sadhasivam
2018-06-28 18:10 ` [PATCH v2 6/6] MAINTAINERS: Add entry for Actions Semi OWL " Manivannan Sadhasivam
2018-06-28 18:10   ` Manivannan Sadhasivam
2018-06-29  4:13 ` [PATCH v2 0/6] Add Actions Semi S900 I2C support Peter Rosin
2018-06-29  4:13   ` Peter Rosin
2018-06-29  4:44   ` Manivannan Sadhasivam
2018-06-29  4:44     ` Manivannan Sadhasivam
2018-06-29  5:09     ` Peter Rosin
2018-06-29  5:09       ` Peter Rosin

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180628181042.2239-5-manivannan.sadhasivam@linaro.org \
    --to=manivannan.sadhasivam@linaro.org \
    --cc=96boards@ucrobotics.com \
    --cc=afaerber@suse.de \
    --cc=amit.kucheria@linaro.org \
    --cc=andy.shevchenko@gmail.com \
    --cc=bdong@ucrobotics.com \
    --cc=daniel.thompson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=hzhang@ucrobotics.com \
    --cc=jeff.chen@actions-semi.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-i2c@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=liuwei@actions-semi.com \
    --cc=manivannanece23@gmail.com \
    --cc=mp-cs@actions-semi.com \
    --cc=robh+dt@kernel.org \
    --cc=thomas.liau@actions-semi.com \
    --cc=wsa@the-dreams.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.