From: Jagan Teki <jagan@amarulasolutions.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 16/25] ARM: dts: sun8i: Update A83T dts(i) files from Linux
Date: Mon, 16 Jul 2018 13:49:47 +0530 [thread overview]
Message-ID: <20180716081956.32434-17-jagan@amarulasolutions.com> (raw)
In-Reply-To: <20180716081956.32434-1-jagan@amarulasolutions.com>
Update all A83T devicetree dtsi and dtsi files from Linux
with below commit:
commit 221cb9fd2ee3042689fe0e6613d0f34eb46a5af6
Author: Mylène Josserand <mylene.josserand@bootlin.com>
Date: Fri May 4 21:05:44 2018 +0200
ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC
Note: bananapi-m3 and cubietruck-plus board dts files has
usb_otg enabled in U-Boot which were not present in Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/axp81x.dtsi | 169 ++++
.../dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 195 +++-
arch/arm/dts/sun8i-a83t-bananapi-m3.dts | 298 +++++-
arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 322 ++++++-
arch/arm/dts/sun8i-a83t-tbs-a711.dts | 355 ++++++-
arch/arm/dts/sun8i-a83t.dtsi | 885 ++++++++++++++++--
include/dt-bindings/clock/sun8i-a83t-ccu.h | 140 +++
include/dt-bindings/reset/sun8i-a83t-ccu.h | 98 ++
8 files changed, 2382 insertions(+), 80 deletions(-)
create mode 100644 arch/arm/dts/axp81x.dtsi
create mode 100644 include/dt-bindings/clock/sun8i-a83t-ccu.h
create mode 100644 include/dt-bindings/reset/sun8i-a83t-ccu.h
diff --git a/arch/arm/dts/axp81x.dtsi b/arch/arm/dts/axp81x.dtsi
new file mode 100644
index 0000000000..043c717dce
--- /dev/null
+++ b/arch/arm/dts/axp81x.dtsi
@@ -0,0 +1,169 @@
+/*
+ * Copyright 2017 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/* AXP813/818 Integrated Power Management Chip */
+
+&axp81x {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ axp_adc: adc {
+ compatible = "x-powers,axp813-adc";
+ #io-channel-cells = <1>;
+ };
+
+ axp_gpio: gpio {
+ compatible = "x-powers,axp813-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio0_ldo: gpio0-ldo {
+ pins = "GPIO0";
+ function = "ldo";
+ };
+
+ gpio1_ldo: gpio1-ldo {
+ pins = "GPIO1";
+ function = "ldo";
+ };
+ };
+
+ battery_power_supply: battery-power-supply {
+ compatible = "x-powers,axp813-battery-power-supply";
+ status = "disabled";
+ };
+
+ regulators {
+ /* Default work frequency for buck regulators */
+ x-powers,dcdc-freq = <3000>;
+
+ reg_dcdc1: dcdc1 {
+ };
+
+ reg_dcdc2: dcdc2 {
+ };
+
+ reg_dcdc3: dcdc3 {
+ };
+
+ reg_dcdc4: dcdc4 {
+ };
+
+ reg_dcdc5: dcdc5 {
+ };
+
+ reg_dcdc6: dcdc6 {
+ };
+
+ reg_dcdc7: dcdc7 {
+ };
+
+ reg_aldo1: aldo1 {
+ };
+
+ reg_aldo2: aldo2 {
+ };
+
+ reg_aldo3: aldo3 {
+ };
+
+ reg_dldo1: dldo1 {
+ };
+
+ reg_dldo2: dldo2 {
+ };
+
+ reg_dldo3: dldo3 {
+ };
+
+ reg_dldo4: dldo4 {
+ };
+
+ reg_eldo1: eldo1 {
+ };
+
+ reg_eldo2: eldo2 {
+ };
+
+ reg_eldo3: eldo3 {
+ };
+
+ reg_fldo1: fldo1 {
+ };
+
+ reg_fldo2: fldo2 {
+ };
+
+ reg_fldo3: fldo3 {
+ };
+
+ reg_ldo_io0: ldo-io0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_ldo>;
+ /* Disable by default to avoid conflicts with GPIO */
+ status = "disabled";
+ };
+
+ reg_ldo_io1: ldo-io1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_ldo>;
+ /* Disable by default to avoid conflicts with GPIO */
+ status = "disabled";
+ };
+
+ reg_rtc_ldo: rtc-ldo {
+ /* RTC_LDO is a fixed, always-on regulator */
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ reg_sw: sw {
+ };
+
+ reg_drivevbus: drivevbus {
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
index c8495d7624..36ecebaff3 100644
--- a/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
+++ b/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
@@ -44,6 +44,8 @@
/dts-v1/;
#include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
/ {
model = "Allwinner A83T H8Homlet Proto Dev Board v2.0";
compatible = "allwinner,h8homlet-v2", "allwinner,sun8i-a83t";
@@ -55,22 +57,213 @@
chosen {
stdout-path = "serial0:115200n8";
};
+
+ reg_usb0_vbus: reg-usb0-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
+ };
+
+ reg_usb1_vbus: reg-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ };
};
&ehci0 {
status = "okay";
};
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
&ohci0 {
status = "okay";
};
+&r_rsb {
+ status = "okay";
+
+ axp81x: pmic at 3a3 {
+ compatible = "x-powers,axp818", "x-powers,axp813";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ swin-supply = <®_dcdc1>;
+ };
+
+ ac100: codec at e89 {
+ compatible = "x-powers,ac100";
+ reg = <0xe89>;
+
+ ac100_codec: codec {
+ compatible = "x-powers,ac100-codec";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
+ #clock-cells = <0>;
+ clock-output-names = "4M_adda";
+ };
+
+ ac100_rtc: rtc {
+ compatible = "x-powers,ac100-rtc";
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&ac100_codec>;
+ #clock-cells = <1>;
+ clock-output-names = "cko1_rtc",
+ "cko2_rtc",
+ "cko3_rtc";
+ };
+ };
+};
+
+#include "axp81x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-1v8";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dram-pll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+};
+
+®_dcdc4 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-mipi";
+};
+
+®_dldo4 {
+ /*
+ * The PHY requires 20ms after all voltages are applied until core
+ * logic is ready and 30ms after the reset pin is de-asserted.
+ * Set a 100ms delay to account for PMIC ramp time and board traces.
+ */
+ regulator-enable-ramp-delay = <100000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ephy";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd12-hsic";
+};
+
+®_fldo2 {
+ /*
+ * Despite the embedded CPUs core not being used in any way,
+ * this must remain on or the system will hang.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+®_sw {
+ regulator-name = "vcc-wifi";
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usbphy {
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
};
&usb_otg {
+ dr_mode = "host";
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
index dfc16a0272..eaff6fa401 100644
--- a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
@@ -1,6 +1,7 @@
/*
- * Copyright 2015 Vishnu Patekar
- * Vishnu Patekar <vishnupatekar0510@gmail.com>
+ * Copyright 2017 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
@@ -44,29 +45,316 @@
/dts-v1/;
#include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
/ {
- model = "Allwinner A83T BananaPi M3 Board v1.2";
- compatible = "bananapi,m3v1.2", "allwinner,sun8i-a83t";
+ model = "Banana Pi BPI-M3";
+ compatible = "sinovoip,bpi-m3", "allwinner,sun8i-a83t";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "bananapi-m3:blue:usr";
+ gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "bananapi-m3:green:usr";
+ gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_usb1_vbus: reg-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ /* The WiFi low power clock must be 32768 Hz */
+ assigned-clocks = <&ac100_rtc 1>;
+ assigned-clock-rates = <32768>;
+ /* enables internal regulator and de-asserts reset */
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+ };
+};
+
+&de {
+ status = "okay";
};
&ehci0 {
+ /* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */
status = "okay";
+
+ /* TODO GL830 USB-to-SATA bridge downstream w/ GPIO power controls */
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_sw>;
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii";
+ allwinner,rx-delay-ps = <700>;
+ allwinner,tx-delay-ps = <700>;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mdio {
+ rgmii_phy: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi at 1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp81x: pmic at 3a3 {
+ compatible = "x-powers,axp813";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ fldoin-supply = <®_dcdc5>;
+ swin-supply = <®_dcdc1>;
+ x-powers,drive-vbus-en;
+ };
+
+ ac100: codec at e89 {
+ compatible = "x-powers,ac100";
+ reg = <0xe89>;
+
+ ac100_codec: codec {
+ compatible = "x-powers,ac100-codec";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
+ #clock-cells = <0>;
+ clock-output-names = "4M_adda";
+ };
+
+ ac100_rtc: rtc {
+ compatible = "x-powers,ac100-rtc";
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&ac100_codec>;
+ #clock-cells = <1>;
+ clock-output-names = "cko1_rtc",
+ "cko2_rtc",
+ "cko3_rtc";
+ };
+ };
+};
+
+#include "axp81x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-1v8";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dram-pll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ /* schematics says 3.1V but FEX file says 3.3V */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+};
+
+®_dcdc4 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ /*
+ * This powers both the WiFi/BT module's main power, I/O supply,
+ * and external pull-ups on all the data lines. It should be set
+ * to the same voltage as the I/O supply (DCDC1 in this case) to
+ * avoid any leakage or mismatch.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pd";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd12-hsic";
+};
+
+®_fldo2 {
+ /*
+ * Despite the embedded CPUs core not being used in any way,
+ * this must remain on or the system will hang.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+®_sw {
+ /*
+ * The PHY requires 20ms after all voltages
+ * are applied until core logic is ready and
+ * 30ms after the reset pin is de-asserted.
+ * Set a 100ms delay to account for PMIC
+ * ramp time and board traces.
+ */
+ regulator-enable-ramp-delay = <100000>;
+ regulator-name = "vcc-ephy";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&usb_otg {
status = "okay";
};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts
index 8437c8f59e..5dba4fc310 100644
--- a/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts
@@ -45,33 +45,353 @@
/dts-v1/;
#include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
/ {
model = "Cubietech Cubietruck Plus";
compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "cubietruck-plus:blue:usr";
+ gpios = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */
+ };
+
+ orange {
+ label = "cubietruck-plus:orange:usr";
+ gpios = <&pio 3 26 GPIO_ACTIVE_HIGH>; /* PD26 */
+ };
+
+ white {
+ label = "cubietruck-plus:white:usr";
+ gpios = <&pio 3 27 GPIO_ACTIVE_HIGH>; /* PD27 */
+ };
+
+ green {
+ label = "cubietruck-plus:green:usr";
+ gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */
+ };
+ };
+
+ usb-hub {
+ /* I2C is not connected */
+ compatible = "smsc,usb3503";
+ initial-mode = <1>; /* initialize in HUB mode */
+ disabled-ports = <1>;
+ intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ reset-gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+ connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+ refclk-frequency = <19200000>;
+ };
+
+ reg_usb1_vbus: reg-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */
+ };
+
+ reg_usb2_vbus: reg-usb2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb2-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_out>;
+ };
+ };
+
+ spdif_out: spdif-out {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ /* The WiFi low power clock must be 32768 Hz */
+ assigned-clocks = <&ac100_rtc 1>;
+ assigned-clock-rates = <32768>;
+ /* enables internal regulator and de-asserts reset */
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+ };
};
&ehci0 {
+ /* GL830 USB-to-SATA bridge here */
status = "okay";
};
&ehci1 {
+ /* USB3503 HSIC USB 2.0 hub here */
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_dldo4>;
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&mdio {
+ rgmii_phy: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_sw>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp81x: pmic at 3a3 {
+ compatible = "x-powers,axp818", "x-powers,axp813";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ swin-supply = <®_dcdc1>;
+ x-powers,drive-vbus-en;
+ };
+
+ ac100: codec at e89 {
+ compatible = "x-powers,ac100";
+ reg = <0xe89>;
+
+ ac100_codec: codec {
+ compatible = "x-powers,ac100-codec";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
+ #clock-cells = <0>;
+ clock-output-names = "4M_adda";
+ };
+
+ ac100_rtc: rtc {
+ compatible = "x-powers,ac100-rtc";
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&ac100_codec>;
+ #clock-cells = <1>;
+ clock-output-names = "cko1_rtc",
+ "cko2_rtc",
+ "cko3_rtc";
+ };
+ };
+};
+
+#include "axp81x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-1v8";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dram-pll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ /*
+ * The schematics say this should be 3.3V, but the FEX file says
+ * it should be 3V. The latter makes sense, as the WiFi module's
+ * I/O is indirectly powered from DCDC1, through SW. It is rated
+ * at 2.98V maximum.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+};
+
+®_dcdc4 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "dp-pwr";
+};
+
+®_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "ephy-io";
+};
+
+®_dldo4 {
+ /*
+ * The PHY requires 20ms after all voltages are applied until core
+ * logic is ready and 30ms after the reset pin is de-asserted.
+ * Set a 100ms delay to account for PMIC ramp time and board traces.
+ */
+ regulator-enable-ramp-delay = <100000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "ephy";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "dp-bridge-1";
+};
+
+®_eldo2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "dp-bridge-2";
+};
+
+®_fldo1 {
+ /* TODO should be handled by USB PHY */
+ regulator-always-on;
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd12-hsic";
+};
+
+®_fldo2 {
+ /*
+ * Despite the embedded CPUs core not being used in any way,
+ * this must remain on or the system will hang.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+®_sw {
+ regulator-name = "vcc-wifi-io";
+};
+
+&spdif {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&usb_otg {
status = "okay";
};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/dts/sun8i-a83t-tbs-a711.dts
index 80e8b1cc90..1537ce148c 100644
--- a/arch/arm/dts/sun8i-a83t-tbs-a711.dts
+++ b/arch/arm/dts/sun8i-a83t-tbs-a711.dts
@@ -1,6 +1,6 @@
/*
- * Copyright 2017 Ondřej Jirman
- * Ondřej Jirman <megous@megous.com>
+ * Copyright (C) 2017 Touchless Biometric Systems AG
+ * Tomas Novotny <tomas@novotny.cz>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
@@ -44,33 +44,380 @@
/dts-v1/;
#include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
/ {
model = "TBS A711 Tablet";
compatible = "tbs-biometrics,a711", "allwinner,sun8i-a83t";
aliases {
serial0 = &uart0;
+ serial1 = &uart1;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ enable-gpios = <&pio 3 29 GPIO_ACTIVE_HIGH>;
+
+ brightness-levels = <0 1 2 4 8 16 32 64 128 255>;
+ default-brightness-level = <9>;
+ };
+
+ panel {
+ compatible = "tbs,a711-panel", "panel-lvds";
+ backlight = <&backlight>;
+ power-supply = <®_sw>;
+
+ width-mm = <153>;
+ height-mm = <90>;
+ data-mapping = "vesa-24";
+
+ panel-timing {
+ /* 1024x600 @60Hz */
+ clock-frequency = <52000000>;
+ hactive = <1024>;
+ vactive = <600>;
+ hsync-len = <20>;
+ hfront-porch = <180>;
+ hback-porch = <160>;
+ vfront-porch = <12>;
+ vback-porch = <23>;
+ vsync-len = <5>;
+ };
+
+ port {
+ panel_input: endpoint {
+ remote-endpoint = <&tcon0_out_lcd>;
+ };
+ };
+ };
+
+ reg_vbat: reg-vbat {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ reg_vmain: reg-vmain {
+ compatible = "regulator-fixed";
+ regulator-name = "vmain";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_vbat>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+
+ /*
+ * This is actually Bluetooth's clock, but we have to
+ * hook it up somewheere
+ */
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&cpu100 {
+ cpu-supply = <®_dcdc3>;
+};
+
+&de {
+ status = "okay";
};
+/*
+ * An USB-2 hub is connected here, which also means we don't need to
+ * enable the OHCI controller.
+ */
&ehci0 {
status = "okay";
};
-&ohci0 {
+/*
+ * There's a modem connected here that needs to be initialised before
+ * being able to be enumerated.
+ */
+&ehci1 {
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_dcdc1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&mmc1 {
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_dldo1>;
+ non-removable;
+ wakeup-source;
+ status = "okay";
+
+ brcmf: wifi at 1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 WL_WAKE_UP */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+ pinctrl-names = "default";
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pin>;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp81x: pmic at 3a3 {
+ compatible = "x-powers,axp813";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ swin-supply = <®_dcdc1>;
+ x-powers,drive-vbus-en;
+ };
+
+ ac100: codec at e89 {
+ compatible = "x-powers,ac100";
+ reg = <0xe89>;
+
+ ac100_codec: codec {
+ compatible = "x-powers,ac100-codec";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 12 IRQ_TYPE_LEVEL_LOW>; /* PL12 */
+ #clock-cells = <0>;
+ clock-output-names = "4M_adda";
+ };
+
+ ac100_rtc: rtc {
+ compatible = "x-powers,ac100-rtc";
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&ac100_codec>;
+ #clock-cells = <1>;
+ clock-output-names = "cko1_rtc",
+ "cko2_rtc",
+ "cko3_rtc";
+ };
+ };
+
+};
+
+#include "axp81x.dtsi"
+
+&battery_power_supply {
+ status = "okay";
+};
+
+®_aldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-1.8";
+};
+
+®_aldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-name = "vdd-drampll";
+};
+
+®_aldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-always-on;
+ regulator-name = "vcc-io";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-name = "vdd-cpu-A";
+};
+
+®_dcdc3 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-name = "vdd-cpu-B";
+};
+
+®_dcdc4 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc5 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <4200000>;
+ regulator-name = "vcc-mipi";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vdd-csi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "avdd-csi";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
status = "okay";
};
+®_eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-csi-r";
+};
+
+®_eldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dsi";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-csi-f";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-hsic";
+};
+
+®_fldo2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-name = "vdd-cpus";
+};
+
+®_ldo_io0 {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-name = "vcc-ctp";
+ status = "okay";
+};
+
+®_ldo_io1 {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-name = "vcc-vb";
+ status = "okay";
+};
+
+®_sw {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-name = "vcc-lcd";
+};
+
+&tcon0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_lvds_pins>;
+};
+
+&tcon0_out {
+ tcon0_out_lcd: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+/* There's the BT part of the AP6210 connected to that UART */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
status = "okay";
};
&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+ usb0_vbus-supply = <®_drivevbus>;
+ usb1_vbus_supply = <®_vmain>;
+ usb2_vbus_supply = <®_vmain>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-a83t.dtsi b/arch/arm/dts/sun8i-a83t.dtsi
index 2953e0fdac..2be23d6009 100644
--- a/arch/arm/dts/sun8i-a83t.dtsi
+++ b/arch/arm/dts/sun8i-a83t.dtsi
@@ -40,67 +40,99 @@
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
-
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/clock/sun8i-a83t-ccu.h>
+#include <dt-bindings/clock/sun8i-de2.h>
+#include <dt-bindings/clock/sun8i-r-ccu.h>
+#include <dt-bindings/reset/sun8i-a83t-ccu.h>
+#include <dt-bindings/reset/sun8i-de2.h>
+#include <dt-bindings/reset/sun8i-r-ccu.h>
/ {
interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
- cpu at 0 {
+ cpu0: cpu at 0 {
+ clocks = <&ccu CLK_C0CPUX>;
+ clock-names = "cpu";
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu0_opp_table>;
+ cci-control-port = <&cci_control0>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <0>;
};
cpu at 1 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu0_opp_table>;
+ cci-control-port = <&cci_control0>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <1>;
};
cpu at 2 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu0_opp_table>;
+ cci-control-port = <&cci_control0>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <2>;
};
cpu at 3 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu0_opp_table>;
+ cci-control-port = <&cci_control0>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <3>;
};
- cpu at 100 {
+ cpu100: cpu at 100 {
+ clocks = <&ccu CLK_C1CPUX>;
+ clock-names = "cpu";
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu1_opp_table>;
+ cci-control-port = <&cci_control1>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <0x100>;
};
cpu at 101 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu1_opp_table>;
+ cci-control-port = <&cci_control1>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <0x101>;
};
cpu at 102 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu1_opp_table>;
+ cci-control-port = <&cci_control1>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <0x102>;
};
cpu at 103 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu1_opp_table>;
+ cci-control-port = <&cci_control1>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <0x103>;
};
};
@@ -123,6 +155,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
@@ -148,48 +181,575 @@
};
};
+ de: display-engine {
+ compatible = "allwinner,sun8i-a83t-display-engine";
+ allwinner,pipelines = <&mixer0>, <&mixer1>;
+ status = "disabled";
+ };
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ device_type = "memory";
+ };
+
+ cpu0_opp_table: opp_table0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-720000000 {
+ opp-hz = /bits/ 64 <720000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-864000000 {
+ opp-hz = /bits/ 64 <864000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-912000000 {
+ opp-hz = /bits/ 64 <912000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1008000000 {
+ opp-hz = /bits/ 64 <1008000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1128000000 {
+ opp-hz = /bits/ 64 <1128000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+ };
+
+ cpu1_opp_table: opp_table1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-720000000 {
+ opp-hz = /bits/ 64 <720000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-864000000 {
+ opp-hz = /bits/ 64 <864000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-912000000 {
+ opp-hz = /bits/ 64 <912000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1008000000 {
+ opp-hz = /bits/ 64 <1008000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1128000000 {
+ opp-hz = /bits/ 64 <1128000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
- pio: pinctrl at 01c20800 {
+ display_clocks: clock at 1000000 {
+ compatible = "allwinner,sun8i-a83t-de2-clk";
+ reg = <0x01000000 0x100000>;
+ clocks = <&ccu CLK_PLL_DE>,
+ <&ccu CLK_BUS_DE>;
+ clock-names = "mod",
+ "bus";
+ resets = <&ccu RST_BUS_DE>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ mixer0: mixer at 1100000 {
+ compatible = "allwinner,sun8i-a83t-de2-mixer-0";
+ reg = <0x01100000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER0>,
+ <&display_clocks CLK_MIXER0>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks RST_MIXER0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer0_out: port at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ mixer0_out_tcon0: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_in_mixer0>;
+ };
+ };
+ };
+ };
+
+ mixer1: mixer at 1200000 {
+ compatible = "allwinner,sun8i-a83t-de2-mixer-1";
+ reg = <0x01200000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER1>,
+ <&display_clocks CLK_MIXER1>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks RST_WB>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer1_out: port at 1 {
+ reg = <1>;
+
+ mixer1_out_tcon1: endpoint {
+ remote-endpoint = <&tcon1_in_mixer1>;
+ };
+ };
+ };
+ };
+
+ cpucfg at 1700000 {
+ compatible = "allwinner,sun8i-a83t-cpucfg";
+ reg = <0x01700000 0x400>;
+ };
+
+ cci at 1790000 {
+ compatible = "arm,cci-400";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x01790000 0x10000>;
+ ranges = <0x0 0x01790000 0x10000>;
+
+ cci_control0: slave-if at 4000 {
+ compatible = "arm,cci-400-ctrl-if";
+ interface-type = "ace";
+ reg = <0x4000 0x1000>;
+ };
+
+ cci_control1: slave-if at 5000 {
+ compatible = "arm,cci-400-ctrl-if";
+ interface-type = "ace";
+ reg = <0x5000 0x1000>;
+ };
+
+ pmu at 9000 {
+ compatible = "arm,cci-400-pmu,r1";
+ reg = <0x9000 0x5000>;
+ interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ syscon: syscon at 1c00000 {
+ compatible = "allwinner,sun8i-a83t-system-controller",
+ "syscon";
+ reg = <0x01c00000 0x1000>;
+ };
+
+ dma: dma-controller at 1c02000 {
+ compatible = "allwinner,sun8i-a83t-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ resets = <&ccu RST_BUS_DMA>;
+ #dma-cells = <1>;
+ };
+
+ tcon0: lcd-controller at 1c0c000 {
+ compatible = "allwinner,sun8i-a83t-tcon-lcd";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
+ clock-names = "ahb", "tcon-ch0";
+ clock-output-names = "tcon-pixel-clock";
+ resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
+ reset-names = "lcd", "lvds";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon0_in_mixer0: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&mixer0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+ };
+
+ tcon1: lcd-controller at 1c0d000 {
+ compatible = "allwinner,sun8i-a83t-tcon-tv";
+ reg = <0x01c0d000 0x1000>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON1>, <&ccu CLK_TCON1>;
+ clock-names = "ahb", "tcon-ch1";
+ resets = <&ccu RST_BUS_TCON1>;
+ reset-names = "lcd";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon1_in: port at 0 {
+ reg = <0>;
+
+ tcon1_in_mixer1: endpoint {
+ remote-endpoint = <&mixer1_out_tcon1>;
+ };
+ };
+
+ tcon1_out: port at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ tcon1_out_hdmi: endpoint at 1 {
+ reg = <1>;
+ remote-endpoint = <&hdmi_in_tcon1>;
+ };
+ };
+ };
+ };
+
+ mmc0: mmc at 1c0f000 {
+ compatible = "allwinner,sun8i-a83t-mmc",
+ "allwinner,sun7i-a20-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc at 1c10000 {
+ compatible = "allwinner,sun8i-a83t-mmc",
+ "allwinner,sun7i-a20-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc at 1c11000 {
+ compatible = "allwinner,sun8i-a83t-emmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sid: eeprom at 1c14000 {
+ compatible = "allwinner,sun8i-a83t-sid";
+ reg = <0x1c14000 0x400>;
+ };
+
+ usb_otg: usb at 1c19000 {
+ compatible = "allwinner,sun8i-a83t-musb",
+ "allwinner,sun8i-a33-musb";
+ reg = <0x01c19000 0x0400>;
+ clocks = <&ccu CLK_BUS_OTG>;
+ resets = <&ccu RST_BUS_OTG>;
+ interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mc";
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ extcon = <&usbphy 0>;
+ status = "disabled";
+ };
+
+ usbphy: phy at 1c19400 {
+ compatible = "allwinner,sun8i-a83t-usb-phy";
+ reg = <0x01c19400 0x10>,
+ <0x01c1a800 0x14>,
+ <0x01c1b800 0x14>;
+ reg-names = "phy_ctrl",
+ "pmu1",
+ "pmu2";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_HSIC>,
+ <&ccu CLK_USB_HSIC_12M>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy",
+ "usb2_hsic_12M";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_HSIC>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci0: usb at 1c1a000 {
+ compatible = "allwinner,sun8i-a83t-ehci",
+ "generic-ehci";
+ reg = <0x01c1a000 0x100>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI0>;
+ resets = <&ccu RST_BUS_EHCI0>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb at 1c1a400 {
+ compatible = "allwinner,sun8i-a83t-ohci",
+ "generic-ohci";
+ reg = <0x01c1a400 0x100>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>, <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci1: usb at 1c1b000 {
+ compatible = "allwinner,sun8i-a83t-ehci",
+ "generic-ehci";
+ reg = <0x01c1b000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ccu: clock at 1c20000 {
+ compatible = "allwinner,sun8i-a83t-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc16Md512>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ pio: pinctrl at 1c20800 {
compatible = "allwinner,sun8i-a83t-pinctrl";
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x01c20800 0x400>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc16Md512>;
+ clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
#interrupt-cells = <3>;
#gpio-cells = <3>;
- mmc0_pins_a: mmc0 at 0 {
- allwinner,pins = "PF0", "PF1", "PF2",
- "PF3", "PF4", "PF5";
- allwinner,function = "mmc0";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ emac_rgmii_pins: emac-rgmii-pins {
+ pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+ "PD11", "PD12", "PD13", "PD14", "PD18",
+ "PD19", "PD21", "PD22", "PD23";
+ function = "gmac";
+ /*
+ * data lines in RGMII mode use DDR mode
+ * and need a higher signal drive strength
+ */
+ drive-strength = <40>;
+ };
+
+ hdmi_pins: hdmi-pins {
+ pins = "PH6", "PH7", "PH8";
+ function = "hdmi";
+ };
+
+ i2c0_pins: i2c0-pins {
+ pins = "PH0", "PH1";
+ function = "i2c0";
+ };
+
+ i2c1_pins: i2c1-pins {
+ pins = "PH2", "PH3";
+ function = "i2c1";
+ };
+
+ i2c2_ph_pins: i2c2-ph-pins {
+ pins = "PH4", "PH5";
+ function = "i2c2";
+ };
+
+ i2s1_pins: i2s1-pins {
+ /* I2S1 does not have external MCLK pin */
+ pins = "PG10", "PG11", "PG12", "PG13";
+ function = "i2s1";
+ };
+
+ lcd_lvds_pins: lcd-lvds-pins {
+ pins = "PD18", "PD19", "PD20", "PD21", "PD22",
+ "PD23", "PD24", "PD25", "PD26", "PD27";
+ function = "lvds0";
+ };
+
+ mmc0_pins: mmc0-pins {
+ pins = "PF0", "PF1", "PF2",
+ "PF3", "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc1_pins: mmc1-pins {
+ pins = "PG0", "PG1", "PG2",
+ "PG3", "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_8bit_emmc_pins: mmc2-8bit-emmc-pins {
+ pins = "PC5", "PC6", "PC8", "PC9",
+ "PC10", "PC11", "PC12", "PC13",
+ "PC14", "PC15", "PC16";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ pwm_pin: pwm-pin {
+ pins = "PD28";
+ function = "pwm";
+ };
+
+ spdif_tx_pin: spdif-tx-pin {
+ pins = "PE18";
+ function = "spdif";
+ };
+
+ uart0_pb_pins: uart0-pb-pins {
+ pins = "PB9", "PB10";
+ function = "uart0";
+ };
+
+ uart0_pf_pins: uart0-pf-pins {
+ pins = "PF2", "PF4";
+ function = "uart0";
};
- uart0_pins_a: uart0 at 0 {
- allwinner,pins = "PF2", "PF4";
- allwinner,function = "uart0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart1_pins: uart1-pins {
+ pins = "PG6", "PG7";
+ function = "uart1";
};
- uart0_pins_b: uart0 at 1 {
- allwinner,pins = "PB9", "PB10";
- allwinner,function = "uart0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart1_rts_cts_pins: uart1-rts-cts-pins {
+ pins = "PG8", "PG9";
+ function = "uart1";
};
};
- timer at 01c20c00 {
+ timer at 1c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0xa0>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
@@ -197,27 +757,166 @@
clocks = <&osc24M>;
};
- watchdog at 01c20ca0 {
+ watchdog at 1c20ca0 {
compatible = "allwinner,sun6i-a31-wdt";
reg = <0x01c20ca0 0x20>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&osc24M>;
};
- uart0: serial at 01c28000 {
+ spdif: spdif at 1c21000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-a83t-spdif",
+ "allwinner,sun8i-h3-spdif";
+ reg = <0x01c21000 0x400>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
+ resets = <&ccu RST_BUS_SPDIF>;
+ clock-names = "apb", "spdif";
+ dmas = <&dma 2>;
+ dma-names = "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx_pin>;
+ status = "disabled";
+ };
+
+ i2s0: i2s at 1c22000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-a83t-i2s";
+ reg = <0x01c22000 0x400>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>;
+ clock-names = "apb", "mod";
+ dmas = <&dma 3>, <&dma 3>;
+ resets = <&ccu RST_BUS_I2S0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2s1: i2s at 1c22400 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-a83t-i2s";
+ reg = <0x01c22400 0x400>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>;
+ clock-names = "apb", "mod";
+ dmas = <&dma 4>, <&dma 4>;
+ resets = <&ccu RST_BUS_I2S1>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1_pins>;
+ status = "disabled";
+ };
+
+ i2s2: i2s at 1c22800 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-a83t-i2s";
+ reg = <0x01c22800 0x400>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S2>, <&ccu CLK_I2S2>;
+ clock-names = "apb", "mod";
+ dmas = <&dma 27>;
+ resets = <&ccu RST_BUS_I2S2>;
+ dma-names = "tx";
+ status = "disabled";
+ };
+
+ pwm: pwm at 1c21400 {
+ compatible = "allwinner,sun8i-a83t-pwm",
+ "allwinner,sun8i-h3-pwm";
+ reg = <0x01c21400 0x400>;
+ clocks = <&osc24M>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ uart0: serial at 1c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
status = "disabled";
};
- gic: interrupt-controller at 01c81000 {
+ uart1: serial at 1c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ status = "disabled";
+ };
+
+ i2c0: i2c at 1c2ac00 {
+ compatible = "allwinner,sun8i-a83t-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c at 1c2b000 {
+ compatible = "allwinner,sun8i-a83t-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c at 1c2b400 {
+ compatible = "allwinner,sun8i-a83t-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ emac: ethernet at 1c30000 {
+ compatible = "allwinner,sun8i-a83t-emac";
+ syscon = <&syscon>;
+ reg = <0x01c30000 0x104>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu 13>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu 27>;
+ clock-names = "stmmaceth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ gic: interrupt-controller at 1c81000 {
compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
reg = <0x01c81000 0x1000>,
- <0x01c82000 0x1000>,
+ <0x01c82000 0x2000>,
<0x01c84000 0x2000>,
<0x01c86000 0x2000>;
interrupt-controller;
@@ -225,59 +924,107 @@
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
};
- usb_otg: usb at 01c19000 {
- compatible = "allwinner,sun8i-a33-musb";
- reg = <0x01c19000 0x400>;
- interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "mc";
- phys = <&usbphy 0>;
- phy-names = "usb";
+ hdmi: hdmi at 1ee0000 {
+ compatible = "allwinner,sun8i-a83t-dw-hdmi";
+ reg = <0x01ee0000 0x10000>;
+ reg-io-width = <1>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_SLOW>,
+ <&ccu CLK_HDMI>;
+ clock-names = "iahb", "isfr", "tmds";
+ resets = <&ccu RST_BUS_HDMI1>;
+ reset-names = "ctrl";
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi-phy";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_pins>;
status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdmi_in: port at 0 {
+ reg = <0>;
+
+ hdmi_in_tcon1: endpoint {
+ remote-endpoint = <&tcon1_out_hdmi>;
+ };
+ };
+
+ hdmi_out: port at 1 {
+ reg = <1>;
+ };
+ };
};
- usbphy: phy at 1c19400 {
- compatible = "allwinner,sun8i-a83t-usb-phy";
- reg = <0x01c19400 0x10>,
- <0x01c1a800 0x14>,
- <0x01c1b800 0x14>;
- reg-names = "phy_ctrl",
- "pmu1",
- "pmu2";
- status = "disabled";
- #phy-cells = <1>;
+ hdmi_phy: hdmi-phy at 1ef0000 {
+ compatible = "allwinner,sun8i-a83t-hdmi-phy";
+ reg = <0x01ef0000 0x10000>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_SLOW>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_HDMI0>;
+ reset-names = "phy";
+ #phy-cells = <0>;
};
- ehci0: usb at 01c1a000 {
- compatible = "allwinner,sun8i-a83t-ehci", "generic-ehci";
- reg = <0x01c1a000 0x100>;
- interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
+ r_intc: interrupt-controller at 1f00c00 {
+ compatible = "allwinner,sun8i-a83t-r-intc",
+ "allwinner,sun6i-a31-r-intc";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x01f00c00 0x400>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
};
- ohci0: usb at 01c1a400 {
- compatible = "allwinner,sun8i-a83t-ohci", "generic-ohci";
- reg = <0x01c1a400 0x100>;
- interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
+ r_ccu: clock at 1f01400 {
+ compatible = "allwinner,sun8i-a83t-r-ccu";
+ reg = <0x01f01400 0x400>;
+ clocks = <&osc24M>, <&osc16Md512>, <&osc16M>,
+ <&ccu 6>;
+ clock-names = "hosc", "losc", "iosc", "pll-periph";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
};
- ehci1: usb at 01c1b000 {
- compatible = "allwinner,sun8i-a83t-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
+ r_cpucfg at 1f01c00 {
+ compatible = "allwinner,sun8i-a83t-r-cpucfg";
+ reg = <0x1f01c00 0x400>;
};
- r_pio: pinctrl at 01f02c00 {
+ r_pio: pinctrl at 1f02c00 {
compatible = "allwinner,sun8i-a83t-r-pinctrl";
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>,
+ <&osc16Md512>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ r_rsb_pins: r-rsb-pins {
+ pins = "PL0", "PL1";
+ function = "s_rsb";
+ drive-strength = <20>;
+ bias-pull-up;
+ };
+ };
+
+ r_rsb: rsb at 1f03400 {
+ compatible = "allwinner,sun8i-a83t-rsb",
+ "allwinner,sun8i-a23-rsb";
+ reg = <0x01f03400 0x400>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_APB0_RSB>;
+ clock-frequency = <3000000>;
+ resets = <&r_ccu RST_APB0_RSB>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_rsb_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
};
};
diff --git a/include/dt-bindings/clock/sun8i-a83t-ccu.h b/include/dt-bindings/clock/sun8i-a83t-ccu.h
new file mode 100644
index 0000000000..78af5085f6
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-a83t-ccu.h
@@ -0,0 +1,140 @@
+/*
+ * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_
+#define _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_
+
+#define CLK_PLL_PERIPH 6
+
+#define CLK_PLL_DE 9
+
+#define CLK_C0CPUX 11
+#define CLK_C1CPUX 12
+
+#define CLK_BUS_MIPI_DSI 19
+#define CLK_BUS_SS 20
+#define CLK_BUS_DMA 21
+#define CLK_BUS_MMC0 22
+#define CLK_BUS_MMC1 23
+#define CLK_BUS_MMC2 24
+#define CLK_BUS_NAND 25
+#define CLK_BUS_DRAM 26
+#define CLK_BUS_EMAC 27
+#define CLK_BUS_HSTIMER 28
+#define CLK_BUS_SPI0 29
+#define CLK_BUS_SPI1 30
+#define CLK_BUS_OTG 31
+#define CLK_BUS_EHCI0 32
+#define CLK_BUS_EHCI1 33
+#define CLK_BUS_OHCI0 34
+
+#define CLK_BUS_VE 35
+#define CLK_BUS_TCON0 36
+#define CLK_BUS_TCON1 37
+#define CLK_BUS_CSI 38
+#define CLK_BUS_HDMI 39
+#define CLK_BUS_DE 40
+#define CLK_BUS_GPU 41
+#define CLK_BUS_MSGBOX 42
+#define CLK_BUS_SPINLOCK 43
+
+#define CLK_BUS_SPDIF 44
+#define CLK_BUS_PIO 45
+#define CLK_BUS_I2S0 46
+#define CLK_BUS_I2S1 47
+#define CLK_BUS_I2S2 48
+#define CLK_BUS_TDM 49
+
+#define CLK_BUS_I2C0 50
+#define CLK_BUS_I2C1 51
+#define CLK_BUS_I2C2 52
+#define CLK_BUS_UART0 53
+#define CLK_BUS_UART1 54
+#define CLK_BUS_UART2 55
+#define CLK_BUS_UART3 56
+#define CLK_BUS_UART4 57
+
+#define CLK_NAND 59
+#define CLK_MMC0 60
+#define CLK_MMC0_SAMPLE 61
+#define CLK_MMC0_OUTPUT 62
+#define CLK_MMC1 63
+#define CLK_MMC1_SAMPLE 64
+#define CLK_MMC1_OUTPUT 65
+#define CLK_MMC2 66
+#define CLK_MMC2_SAMPLE 67
+#define CLK_MMC2_OUTPUT 68
+#define CLK_SS 69
+#define CLK_SPI0 70
+#define CLK_SPI1 71
+#define CLK_I2S0 72
+#define CLK_I2S1 73
+#define CLK_I2S2 74
+#define CLK_TDM 75
+#define CLK_SPDIF 76
+#define CLK_USB_PHY0 77
+#define CLK_USB_PHY1 78
+#define CLK_USB_HSIC 79
+#define CLK_USB_HSIC_12M 80
+#define CLK_USB_OHCI0 81
+
+#define CLK_DRAM_VE 83
+#define CLK_DRAM_CSI 84
+
+#define CLK_TCON0 85
+#define CLK_TCON1 86
+#define CLK_CSI_MISC 87
+#define CLK_MIPI_CSI 88
+#define CLK_CSI_MCLK 89
+#define CLK_CSI_SCLK 90
+#define CLK_VE 91
+#define CLK_AVS 92
+#define CLK_HDMI 93
+#define CLK_HDMI_SLOW 94
+
+#define CLK_MIPI_DSI0 96
+#define CLK_MIPI_DSI1 97
+#define CLK_GPU_CORE 98
+#define CLK_GPU_MEMORY 99
+#define CLK_GPU_HYD 100
+
+#endif /* _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun8i-a83t-ccu.h b/include/dt-bindings/reset/sun8i-a83t-ccu.h
new file mode 100644
index 0000000000..784f6e1166
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-a83t-ccu.h
@@ -0,0 +1,98 @@
+/*
+ * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_
+#define _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_
+
+#define RST_USB_PHY0 0
+#define RST_USB_PHY1 1
+#define RST_USB_HSIC 2
+
+#define RST_DRAM 3
+#define RST_MBUS 4
+
+#define RST_BUS_MIPI_DSI 5
+#define RST_BUS_SS 6
+#define RST_BUS_DMA 7
+#define RST_BUS_MMC0 8
+#define RST_BUS_MMC1 9
+#define RST_BUS_MMC2 10
+#define RST_BUS_NAND 11
+#define RST_BUS_DRAM 12
+#define RST_BUS_EMAC 13
+#define RST_BUS_HSTIMER 14
+#define RST_BUS_SPI0 15
+#define RST_BUS_SPI1 16
+#define RST_BUS_OTG 17
+#define RST_BUS_EHCI0 18
+#define RST_BUS_EHCI1 19
+#define RST_BUS_OHCI0 20
+
+#define RST_BUS_VE 21
+#define RST_BUS_TCON0 22
+#define RST_BUS_TCON1 23
+#define RST_BUS_CSI 24
+#define RST_BUS_HDMI0 25
+#define RST_BUS_HDMI1 26
+#define RST_BUS_DE 27
+#define RST_BUS_GPU 28
+#define RST_BUS_MSGBOX 29
+#define RST_BUS_SPINLOCK 30
+
+#define RST_BUS_LVDS 31
+
+#define RST_BUS_SPDIF 32
+#define RST_BUS_I2S0 33
+#define RST_BUS_I2S1 34
+#define RST_BUS_I2S2 35
+#define RST_BUS_TDM 36
+
+#define RST_BUS_I2C0 37
+#define RST_BUS_I2C1 38
+#define RST_BUS_I2C2 39
+#define RST_BUS_UART0 40
+#define RST_BUS_UART1 41
+#define RST_BUS_UART2 42
+#define RST_BUS_UART3 43
+#define RST_BUS_UART4 44
+
+#endif /* _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_ */
--
2.17.1
next prev parent reply other threads:[~2018-07-16 8:19 UTC|newest]
Thread overview: 59+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-07-16 8:19 [U-Boot] [PATCH 00/25] sunxi: Enable DM_MMC for U-Boot proper Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 01/25] ARM: dts: sun4i: Sync A10 MMC nodes from Linux Jagan Teki
2018-07-16 9:30 ` Maxime Ripard
2018-07-16 10:28 ` Jagan Teki
2018-07-16 13:37 ` Maxime Ripard
2018-07-16 8:19 ` [U-Boot] [PATCH 02/25] ARM: dts: sun4i: Sync A10 board dts mmc0 node " Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 03/25] ARM: dts: sun4i: Add mmc0 node for iNet 3F Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 04/25] ARM: dts: sun4i: Add mmc0 node for iNet 3W Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 05/25] dm: mmc: sunxi: Refactor ahb gate and clock setup Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 06/25] dm: mmc: sunxi: Add ahb reset0 register write Jagan Teki
2018-07-16 9:39 ` Maxime Ripard
2018-07-16 9:55 ` Jagan Teki
2018-07-16 10:02 ` Maxime Ripard
2018-07-16 10:39 ` Jagan Teki
2018-07-16 13:36 ` Maxime Ripard
2018-07-16 8:19 ` [U-Boot] [PATCH 07/25] ARM: dts: sun7i: Sync A20 MMC nodes from Linux Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 08/25] ARM: dts: sun7i: Add mmc0 node for Primo73 tablet Jagan Teki
2018-07-16 9:40 ` Maxime Ripard
2018-07-16 10:03 ` Jagan Teki
2018-07-16 10:09 ` Chen-Yu Tsai
2018-07-16 8:19 ` [U-Boot] [PATCH 09/25] ARM: dts: sun7i: Add mmc0 node for Ainol AW1 Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 10/25] ARM: dts: sun7i: Add mmc0 node for Mele M5 Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 11/25] ARM: dts: sun7i: Add mmc0 node for Toptech BD1078 Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 12/25] sunxi: A20: Enable DM_MMC Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 13/25] mmc: sunxi: Add mmc, emmc H5/A64 compatible Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 14/25] sunxi: H3_H5: Enable DM_MMC Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 15/25] sunxi: A64: " Jagan Teki
2018-07-16 8:19 ` Jagan Teki [this message]
2018-07-16 8:19 ` [U-Boot] [PATCH 17/25] mmc: sunxi: Add A83T emmc compatible Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 18/25] sunxi: A83T: Enable DM_MMC Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 19/25] ARM: dts: sun8i: Update R40 dts(i) files from Linux Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 20/25] sunxi: V40: Enable DM_MMC Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 21/25] fastboot: sunxi: Update fastboot mmc default device Jagan Teki
2018-07-16 9:46 ` Maxime Ripard
2018-07-16 10:12 ` Jagan Teki
2018-07-16 11:11 ` Alex Kiernan
2018-07-17 11:57 ` Maxime Ripard
2018-07-18 19:15 ` Alex Kiernan
2018-07-19 13:26 ` Maxime Ripard
2018-07-19 18:11 ` Jagan Teki
2018-07-20 7:39 ` Maxime Ripard
2018-07-19 18:43 ` Alex Kiernan
2018-07-20 7:34 ` Maxime Ripard
2018-07-17 11:56 ` Maxime Ripard
2018-07-16 8:19 ` [U-Boot] [PATCH 22/25] env: sunxi: Update default env fat device Jagan Teki
2018-07-16 9:47 ` Maxime Ripard
2018-07-16 10:16 ` Jagan Teki
2018-07-17 11:54 ` Maxime Ripard
2018-07-19 18:21 ` Jagan Teki
2018-07-16 8:19 ` [U-Boot] [PATCH 23/25] sunxi: Use mmc_bootdev=2 for MMC2 boot Jagan Teki
2018-07-16 9:48 ` Maxime Ripard
2018-07-16 10:21 ` Jagan Teki
2018-07-17 11:55 ` Maxime Ripard
2018-07-16 8:19 ` [U-Boot] [DO NOT MERGE PATCH 24/25] sunxi: A13/A31: Enable DM_MMC Jagan Teki
2018-07-16 8:19 ` [U-Boot] [DO NOT MERGE PATCH 25/25] sunxi: A23/A33/V3S: " Jagan Teki
2018-07-16 8:35 ` [U-Boot] [PATCH 00/25] sunxi: Enable DM_MMC for U-Boot proper Chen-Yu Tsai
2018-07-16 9:52 ` Maxime Ripard
2018-07-16 11:08 ` Andre Przywara
2018-07-16 11:42 ` Jagan Teki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180716081956.32434-17-jagan@amarulasolutions.com \
--to=jagan@amarulasolutions.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.