All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v3 1/3] ARM: dts: i.MX6: imx6dl-mamoj: Add parallel display support
@ 2018-07-17  9:25 ` Jagan Teki
  0 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2018-07-17  9:25 UTC (permalink / raw)
  To: Shawn Guo, Sascha Hauer, Fabio Estevam
  Cc: linux-arm-kernel, devicetree, linux-kernel, Rob Herring,
	Mark Rutland, Fabio maggi, lamiaposta71, Andrea CORTESE,
	Davide Bonfanti, Shyam Saini, Michael Trimarchi, Jagan Teki,
	Simone CIANNI, Raffaele RECALCATI

This patch adds parallel display support for i.MX6DL Mamoj board
along with relevant backlight through pwm.

LCD power sequence is added by 'Michael Trimarchi'.

Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes for v3:
- update node name lcd_display as display
- Use proper vlaue with VDOUT_RESET pin 
- updtae pinctrl_lcd_power iomux label as pinctrl_ipu1_lcdif_pwr
Changes for v2:
- collect Fabio r-w-b tag

 arch/arm/boot/dts/imx6dl-mamoj.dts | 185 +++++++++++++++++++++++++++++
 1 file changed, 185 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/imx6dl-mamoj.dts
index 6b2d29138bed..38e94fd11a3f 100644
--- a/arch/arm/boot/dts/imx6dl-mamoj.dts
+++ b/arch/arm/boot/dts/imx6dl-mamoj.dts
@@ -6,11 +6,133 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include "imx6dl.dtsi"
 
 / {
 	model = "BTicino i.MX6DL Mamoj board";
 	compatible = "bticino,imx6dl-mamoj", "fsl,imx6dl";
+
+	backlight_lcd: backlight-lcd {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 25000>; /* 25000ns -> 40kHz */
+		brightness-levels = <0 4 8 16 32 64 128 160 192 224 255>;
+		default-brightness-level = <7>;
+	};
+
+	display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel-lcd {
+		compatible = "rocktech,rk070er9427";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_lcd_lr>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif_pwr>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_lcd_3v3: regulator-lcd-dvdd {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-dvdd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 1 0>;
+		enable-active-high;
+		startup-delay-us = <21000>;
+	};
+
+	reg_lcd_power: regulator-lcd-power {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-enable";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 6 0>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_3v3>;
+	};
+
+	reg_lcd_vgl: regulator-lcd-vgl {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-vgl";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <6000>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_power>;
+	};
+
+	reg_lcd_vgh: regulator-lcd-vgh {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-vgh";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <6000>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_avdd>;
+	};
+
+	reg_lcd_vcom: regulator-lcd-vcom {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-vcom";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <11000>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_vgh>;
+	};
+
+	reg_lcd_lr: regulator-lcd-lr {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-lr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_vcom>;
+	};
+
+	reg_lcd_avdd: regulator-lcd-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-avdd";
+		regulator-min-microvolt = <10280000>;
+		regulator-max-microvolt = <10280000>;
+		gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <6000>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_vgl>;
+	};
 };
 
 &fec {
@@ -147,6 +269,16 @@
 	};
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
@@ -200,6 +332,59 @@
 		>;
 	};
 
+	pinctrl_ipu1_lcdif: pinctrlipu1lcdif { /* parallel port 24-bit */
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 /* VDOUT_PCLK */
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02        0x10 /* VDOUT_HSYNC */
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03        0x10 /* VDOUT_VSYNC */
+			MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04	   0x10 /* VDOUT_RESET */
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00   0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01   0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02   0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17  0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18  0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19  0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20  0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21  0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22  0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23  0x10
+		>;
+	};
+
+	pinctrl_ipu1_lcdif_pwr: ipu1lcdifpwrgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA1__GPIO3_IO01		0x40013058 /* EN_LCD33V */
+			MX6QDL_PAD_SD4_DAT5__GPIO2_IO13		0x4001b0b0 /* EN_AVDD */
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x40013058 /* ENVGH */
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20		0x40013058 /* ENVGL */
+			MX6QDL_PAD_EIM_DA6__GPIO3_IO06		0x40013058 /* LCD_POWER */
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x40013058 /* EN_VCOM_LCD */
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x40013058 /* LCD_L_R */
+			MX6QDL_PAD_EIM_DA2__GPIO3_IO02		0x40013058 /* LCD_U_D */
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+		>;
+	};
+
 	pinctrl_uart3: uart3grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 8+ messages in thread
* [PATCH v3 1/3] ARM: dts: i.MX6: imx6dl-mamoj: Add parallel display support
@ 2018-07-17  9:25 ` Jagan Teki
  0 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2018-07-17  9:25 UTC (permalink / raw)
  To: linux-arm-kernel

This patch adds parallel display support for i.MX6DL Mamoj board
along with relevant backlight through pwm.

LCD power sequence is added by 'Michael Trimarchi'.

Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes for v3:
- update node name lcd_display as display
- Use proper vlaue with VDOUT_RESET pin 
- updtae pinctrl_lcd_power iomux label as pinctrl_ipu1_lcdif_pwr
Changes for v2:
- collect Fabio r-w-b tag

 arch/arm/boot/dts/imx6dl-mamoj.dts | 185 +++++++++++++++++++++++++++++
 1 file changed, 185 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/imx6dl-mamoj.dts
index 6b2d29138bed..38e94fd11a3f 100644
--- a/arch/arm/boot/dts/imx6dl-mamoj.dts
+++ b/arch/arm/boot/dts/imx6dl-mamoj.dts
@@ -6,11 +6,133 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include "imx6dl.dtsi"
 
 / {
 	model = "BTicino i.MX6DL Mamoj board";
 	compatible = "bticino,imx6dl-mamoj", "fsl,imx6dl";
+
+	backlight_lcd: backlight-lcd {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 25000>; /* 25000ns -> 40kHz */
+		brightness-levels = <0 4 8 16 32 64 128 160 192 224 255>;
+		default-brightness-level = <7>;
+	};
+
+	display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
+		status = "okay";
+
+		port at 0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port at 1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel-lcd {
+		compatible = "rocktech,rk070er9427";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_lcd_lr>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif_pwr>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_lcd_3v3: regulator-lcd-dvdd {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-dvdd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 1 0>;
+		enable-active-high;
+		startup-delay-us = <21000>;
+	};
+
+	reg_lcd_power: regulator-lcd-power {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-enable";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 6 0>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_3v3>;
+	};
+
+	reg_lcd_vgl: regulator-lcd-vgl {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-vgl";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <6000>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_power>;
+	};
+
+	reg_lcd_vgh: regulator-lcd-vgh {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-vgh";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <6000>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_avdd>;
+	};
+
+	reg_lcd_vcom: regulator-lcd-vcom {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-vcom";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <11000>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_vgh>;
+	};
+
+	reg_lcd_lr: regulator-lcd-lr {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-lr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_vcom>;
+	};
+
+	reg_lcd_avdd: regulator-lcd-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-avdd";
+		regulator-min-microvolt = <10280000>;
+		regulator-max-microvolt = <10280000>;
+		gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <6000>;
+		enable-active-high;
+		vin-supply = <&reg_lcd_vgl>;
+	};
 };
 
 &fec {
@@ -147,6 +269,16 @@
 	};
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
@@ -200,6 +332,59 @@
 		>;
 	};
 
+	pinctrl_ipu1_lcdif: pinctrlipu1lcdif { /* parallel port 24-bit */
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 /* VDOUT_PCLK */
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02        0x10 /* VDOUT_HSYNC */
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03        0x10 /* VDOUT_VSYNC */
+			MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04	   0x10 /* VDOUT_RESET */
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00   0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01   0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02   0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17  0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18  0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19  0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20  0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21  0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22  0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23  0x10
+		>;
+	};
+
+	pinctrl_ipu1_lcdif_pwr: ipu1lcdifpwrgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA1__GPIO3_IO01		0x40013058 /* EN_LCD33V */
+			MX6QDL_PAD_SD4_DAT5__GPIO2_IO13		0x4001b0b0 /* EN_AVDD */
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x40013058 /* ENVGH */
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20		0x40013058 /* ENVGL */
+			MX6QDL_PAD_EIM_DA6__GPIO3_IO06		0x40013058 /* LCD_POWER */
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x40013058 /* EN_VCOM_LCD */
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x40013058 /* LCD_L_R */
+			MX6QDL_PAD_EIM_DA2__GPIO3_IO02		0x40013058 /* LCD_U_D */
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+		>;
+	};
+
 	pinctrl_uart3: uart3grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
-- 
2.17.1

^ permalink raw reply related	[flat|nested] 8+ messages in thread
* [PATCH v3 2/3] ARM: dts: i.MX6: imx6dl-mamoj: Add Wifi support
  2018-07-17  9:25 ` Jagan Teki
@ 2018-07-17  9:25   ` Jagan Teki
  -1 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2018-07-17  9:25 UTC (permalink / raw)
  To: Shawn Guo, Sascha Hauer, Fabio Estevam
  Cc: linux-arm-kernel, devicetree, linux-kernel, Rob Herring,
	Mark Rutland, Fabio maggi, lamiaposta71, Andrea CORTESE,
	Davide Bonfanti, Shyam Saini, Michael Trimarchi, Jagan Teki,
	Simone CIANNI, Raffaele RECALCATI

Add TI WL18XX Wifi for BTicino i.MX6DL board.

Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes for v3:
- wlan is replace with wlangrp on iomux node
Changes for v2:
- collect Fabio r-w-b tag

 arch/arm/boot/dts/imx6dl-mamoj.dts | 53 ++++++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/imx6dl-mamoj.dts
index 38e94fd11a3f..530cb20ccc86 100644
--- a/arch/arm/boot/dts/imx6dl-mamoj.dts
+++ b/arch/arm/boot/dts/imx6dl-mamoj.dts
@@ -133,6 +133,18 @@
 		enable-active-high;
 		vin-supply = <&reg_lcd_vgl>;
 	};
+
+	reg_wl18xx_vmmc:  regulator-wl18xx-vmcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1807";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wlan>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio6 21 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
 };
 
 &fec {
@@ -285,6 +297,30 @@
 	status = "okay";
 };
 
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_wl18xx_vmmc>;
+	no-1-8-v;
+	non-removable;
+	wakeup-source;
+	keep-power-in-suspend;
+	cap-power-off-card;
+	max-frequency = <25000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1837";
+		reg = <2>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+		tcxo-clock-frequency = <26000000>;
+	};
+};
+
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
@@ -392,6 +428,17 @@
 		>;
 	};
 
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17069
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10079
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17069
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17069
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17069
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17069
+		>;
+	};
+
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x17059
@@ -406,4 +453,10 @@
 			MX6QDL_PAD_SD3_DAT7__SD3_DATA7	0x17059
 		>;
 	};
+
+	pinctrl_wlan: wlangrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD1__GPIO6_IO21	0x4001b0b0
+		>;
+	};
 };
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 8+ messages in thread
* [PATCH v3 2/3] ARM: dts: i.MX6: imx6dl-mamoj: Add Wifi support
@ 2018-07-17  9:25   ` Jagan Teki
  0 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2018-07-17  9:25 UTC (permalink / raw)
  To: linux-arm-kernel

Add TI WL18XX Wifi for BTicino i.MX6DL board.

Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes for v3:
- wlan is replace with wlangrp on iomux node
Changes for v2:
- collect Fabio r-w-b tag

 arch/arm/boot/dts/imx6dl-mamoj.dts | 53 ++++++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/imx6dl-mamoj.dts
index 38e94fd11a3f..530cb20ccc86 100644
--- a/arch/arm/boot/dts/imx6dl-mamoj.dts
+++ b/arch/arm/boot/dts/imx6dl-mamoj.dts
@@ -133,6 +133,18 @@
 		enable-active-high;
 		vin-supply = <&reg_lcd_vgl>;
 	};
+
+	reg_wl18xx_vmmc:  regulator-wl18xx-vmcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1807";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wlan>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio6 21 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
 };
 
 &fec {
@@ -285,6 +297,30 @@
 	status = "okay";
 };
 
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_wl18xx_vmmc>;
+	no-1-8-v;
+	non-removable;
+	wakeup-source;
+	keep-power-in-suspend;
+	cap-power-off-card;
+	max-frequency = <25000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wlcore: wlcore at 2 {
+		compatible = "ti,wl1837";
+		reg = <2>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+		tcxo-clock-frequency = <26000000>;
+	};
+};
+
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
@@ -392,6 +428,17 @@
 		>;
 	};
 
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17069
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10079
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17069
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17069
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17069
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17069
+		>;
+	};
+
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x17059
@@ -406,4 +453,10 @@
 			MX6QDL_PAD_SD3_DAT7__SD3_DATA7	0x17059
 		>;
 	};
+
+	pinctrl_wlan: wlangrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD1__GPIO6_IO21	0x4001b0b0
+		>;
+	};
 };
-- 
2.17.1

^ permalink raw reply related	[flat|nested] 8+ messages in thread
* [PATCH v3 3/3] ARM: dts: i.MX6: imx6dl-mamoj: Add usb host and device support
  2018-07-17  9:25 ` Jagan Teki
@ 2018-07-17  9:25   ` Jagan Teki
  -1 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2018-07-17  9:25 UTC (permalink / raw)
  To: Shawn Guo, Sascha Hauer, Fabio Estevam
  Cc: linux-arm-kernel, devicetree, linux-kernel, Rob Herring,
	Mark Rutland, Fabio maggi, lamiaposta71, Andrea CORTESE,
	Davide Bonfanti, Shyam Saini, Michael Trimarchi, Simone CIANNI,
	Raffaele RECALCATI, Jagan Teki

From: Michael Trimarchi <michael@amarulasolutions.com>

Add USB host and device support for BTicino i.MX6DL Mamoj board.

Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes for v3:
- usbhost is replace with usbhostgrp on iomux node
Changes for v2:
- collect Fabio r-w-b tag

 arch/arm/boot/dts/imx6dl-mamoj.dts | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/imx6dl-mamoj.dts
index 530cb20ccc86..df8607fe4142 100644
--- a/arch/arm/boot/dts/imx6dl-mamoj.dts
+++ b/arch/arm/boot/dts/imx6dl-mamoj.dts
@@ -134,6 +134,17 @@
 		vin-supply = <&reg_lcd_vgl>;
 	};
 
+	reg_usb_host: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usbhost-vbus";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbhost>;
+		regulator-min-microvolt = <50000000>;
+		regulator-max-microvolt = <50000000>;
+		gpio = <&gpio6 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	reg_wl18xx_vmmc:  regulator-wl18xx-vmcc {
 		compatible = "regulator-fixed";
 		regulator-name = "vwl1807";
@@ -297,6 +308,16 @@
 	status = "okay";
 };
 
+&usbh1 {
+	vbus-supply = <&reg_usb_host>;
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
@@ -428,6 +449,12 @@
 		>;
 	};
 
+	pinctrl_usbhost: usbhostgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06		0x4001b0b0
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17069
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 8+ messages in thread
* [PATCH v3 3/3] ARM: dts: i.MX6: imx6dl-mamoj: Add usb host and device support
@ 2018-07-17  9:25   ` Jagan Teki
  0 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2018-07-17  9:25 UTC (permalink / raw)
  To: linux-arm-kernel

From: Michael Trimarchi <michael@amarulasolutions.com>

Add USB host and device support for BTicino i.MX6DL Mamoj board.

Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes for v3:
- usbhost is replace with usbhostgrp on iomux node
Changes for v2:
- collect Fabio r-w-b tag

 arch/arm/boot/dts/imx6dl-mamoj.dts | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/imx6dl-mamoj.dts
index 530cb20ccc86..df8607fe4142 100644
--- a/arch/arm/boot/dts/imx6dl-mamoj.dts
+++ b/arch/arm/boot/dts/imx6dl-mamoj.dts
@@ -134,6 +134,17 @@
 		vin-supply = <&reg_lcd_vgl>;
 	};
 
+	reg_usb_host: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usbhost-vbus";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbhost>;
+		regulator-min-microvolt = <50000000>;
+		regulator-max-microvolt = <50000000>;
+		gpio = <&gpio6 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	reg_wl18xx_vmmc:  regulator-wl18xx-vmcc {
 		compatible = "regulator-fixed";
 		regulator-name = "vwl1807";
@@ -297,6 +308,16 @@
 	status = "okay";
 };
 
+&usbh1 {
+	vbus-supply = <&reg_usb_host>;
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
@@ -428,6 +449,12 @@
 		>;
 	};
 
+	pinctrl_usbhost: usbhostgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06		0x4001b0b0
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17069
-- 
2.17.1

^ permalink raw reply related	[flat|nested] 8+ messages in thread
* Re: [PATCH v3 1/3] ARM: dts: i.MX6: imx6dl-mamoj: Add parallel display support
  2018-07-17  9:25 ` Jagan Teki
@ 2018-07-19  2:46   ` Shawn Guo
  -1 siblings, 0 replies; 8+ messages in thread
From: Shawn Guo @ 2018-07-19  2:46 UTC (permalink / raw)
  To: Jagan Teki
  Cc: Sascha Hauer, Fabio Estevam, linux-arm-kernel, devicetree,
	linux-kernel, Rob Herring, Mark Rutland, Fabio maggi,
	lamiaposta71, Andrea CORTESE, Davide Bonfanti, Shyam Saini,
	Michael Trimarchi, Simone CIANNI, Raffaele RECALCATI

On Tue, Jul 17, 2018 at 02:55:24PM +0530, Jagan Teki wrote:
> This patch adds parallel display support for i.MX6DL Mamoj board
> along with relevant backlight through pwm.
> 
> LCD power sequence is added by 'Michael Trimarchi'.
> 
> Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

'ARM: dts: imx6dl-mamoj: ...' being prefix is good enough.  I fixed it
up and applied all.

Shawn

^ permalink raw reply	[flat|nested] 8+ messages in thread
* [PATCH v3 1/3] ARM: dts: i.MX6: imx6dl-mamoj: Add parallel display support
@ 2018-07-19  2:46   ` Shawn Guo
  0 siblings, 0 replies; 8+ messages in thread
From: Shawn Guo @ 2018-07-19  2:46 UTC (permalink / raw)
  To: linux-arm-kernel

On Tue, Jul 17, 2018 at 02:55:24PM +0530, Jagan Teki wrote:
> This patch adds parallel display support for i.MX6DL Mamoj board
> along with relevant backlight through pwm.
> 
> LCD power sequence is added by 'Michael Trimarchi'.
> 
> Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

'ARM: dts: imx6dl-mamoj: ...' being prefix is good enough.  I fixed it
up and applied all.

Shawn

^ permalink raw reply	[flat|nested] 8+ messages in thread
end of thread, other threads:[~2018-07-19  2:46 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-07-17  9:25 [PATCH v3 1/3] ARM: dts: i.MX6: imx6dl-mamoj: Add parallel display support Jagan Teki
2018-07-17  9:25 ` Jagan Teki
2018-07-17  9:25 ` [PATCH v3 2/3] ARM: dts: i.MX6: imx6dl-mamoj: Add Wifi support Jagan Teki
2018-07-17  9:25   ` Jagan Teki
2018-07-17  9:25 ` [PATCH v3 3/3] ARM: dts: i.MX6: imx6dl-mamoj: Add usb host and device support Jagan Teki
2018-07-17  9:25   ` Jagan Teki
2018-07-19  2:46 ` [PATCH v3 1/3] ARM: dts: i.MX6: imx6dl-mamoj: Add parallel display support Shawn Guo
2018-07-19  2:46   ` Shawn Guo

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.