* [U-Boot] [PATCH u-boot 0/2] Add support for the FriendlyElec NanoPi K2 board
@ 2018-06-25 14:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2018-06-25 14:50 UTC (permalink / raw)
To: u-boot
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
A sync with Linux 4.17 to get the device tree is also necessary.
Neil Armstrong (1):
ARM: dts: sync meson-gxbb-nanopi-k2 from Linux 4.17
Thomas McKahan (1):
boards: amlogic: Add FriendlyElec NanoPi K2 board support
arch/arm/dts/Makefile | 2 +
arch/arm/dts/meson-gxbb-nanopi-k2.dts | 323 ++++++++++++++++++++++++++++++++++
arch/arm/mach-meson/Kconfig | 8 +
board/amlogic/nanopi-k2/Kconfig | 12 ++
board/amlogic/nanopi-k2/MAINTAINERS | 6 +
board/amlogic/nanopi-k2/Makefile | 7 +
board/amlogic/nanopi-k2/README | 99 +++++++++++
board/amlogic/nanopi-k2/nanopi-k2.c | 61 +++++++
configs/nanopi-k2_defconfig | 40 +++++
include/configs/nanopi-k2.h | 18 ++
10 files changed, 576 insertions(+)
create mode 100644 arch/arm/dts/meson-gxbb-nanopi-k2.dts
create mode 100644 board/amlogic/nanopi-k2/Kconfig
create mode 100644 board/amlogic/nanopi-k2/MAINTAINERS
create mode 100644 board/amlogic/nanopi-k2/Makefile
create mode 100644 board/amlogic/nanopi-k2/README
create mode 100644 board/amlogic/nanopi-k2/nanopi-k2.c
create mode 100644 configs/nanopi-k2_defconfig
create mode 100644 include/configs/nanopi-k2.h
--
2.7.4
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH u-boot 0/2] Add support for the FriendlyElec NanoPi K2 board
@ 2018-06-25 14:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2018-06-25 14:50 UTC (permalink / raw)
To: linus-amlogic
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
A sync with Linux 4.17 to get the device tree is also necessary.
Neil Armstrong (1):
ARM: dts: sync meson-gxbb-nanopi-k2 from Linux 4.17
Thomas McKahan (1):
boards: amlogic: Add FriendlyElec NanoPi K2 board support
arch/arm/dts/Makefile | 2 +
arch/arm/dts/meson-gxbb-nanopi-k2.dts | 323 ++++++++++++++++++++++++++++++++++
arch/arm/mach-meson/Kconfig | 8 +
board/amlogic/nanopi-k2/Kconfig | 12 ++
board/amlogic/nanopi-k2/MAINTAINERS | 6 +
board/amlogic/nanopi-k2/Makefile | 7 +
board/amlogic/nanopi-k2/README | 99 +++++++++++
board/amlogic/nanopi-k2/nanopi-k2.c | 61 +++++++
configs/nanopi-k2_defconfig | 40 +++++
include/configs/nanopi-k2.h | 18 ++
10 files changed, 576 insertions(+)
create mode 100644 arch/arm/dts/meson-gxbb-nanopi-k2.dts
create mode 100644 board/amlogic/nanopi-k2/Kconfig
create mode 100644 board/amlogic/nanopi-k2/MAINTAINERS
create mode 100644 board/amlogic/nanopi-k2/Makefile
create mode 100644 board/amlogic/nanopi-k2/README
create mode 100644 board/amlogic/nanopi-k2/nanopi-k2.c
create mode 100644 configs/nanopi-k2_defconfig
create mode 100644 include/configs/nanopi-k2.h
--
2.7.4
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH u-boot 1/2] ARM: dts: sync meson-gxbb-nanopi-k2 from Linux 4.17
2018-06-25 14:50 ` Neil Armstrong
@ 2018-06-25 14:50 ` Neil Armstrong
-1 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2018-06-25 14:50 UTC (permalink / raw)
To: u-boot
Get the meson-gxbb-nanopi-k2.dts file from Linux 4.17.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/meson-gxbb-nanopi-k2.dts | 323 ++++++++++++++++++++++++++++++++++
2 files changed, 324 insertions(+)
create mode 100644 arch/arm/dts/meson-gxbb-nanopi-k2.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 493652e..bcbaae2 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -53,6 +53,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3399-puma-ddr1866.dtb \
rv1108-evb.dtb
dtb-$(CONFIG_ARCH_MESON) += \
+ meson-gxbb-nanopi-k2.dtb \
meson-gxbb-odroidc2.dtb \
meson-gxl-s905x-p212.dtb \
meson-gxl-s905x-libretech-cc.dtb \
diff --git a/arch/arm/dts/meson-gxbb-nanopi-k2.dts b/arch/arm/dts/meson-gxbb-nanopi-k2.dts
new file mode 100644
index 0000000..7d5709c
--- /dev/null
+++ b/arch/arm/dts/meson-gxbb-nanopi-k2.dts
@@ -0,0 +1,323 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ */
+
+/dts-v1/;
+
+#include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
+
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ stat {
+ label = "nanopi-k2:blue:stat";
+ gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ panic-indicator;
+ };
+ };
+
+ vdd_5v: regulator-vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vddio_ao18: regulator-vddio-ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddio_ao3v3: regulator-vddio-ao3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vddio_tf: regulator-vddio-tf {
+ compatible = "regulator-gpio";
+
+ regulator-name = "VDDIO_TF";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0>,
+ <1800000 1>;
+
+ regulator-settling-time-up-us = <100>;
+ regulator-settling-time-down-us = <5000>;
+ };
+
+ wifi_32k: wifi-32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi_32k>;
+ clock-names = "ext_clock";
+ };
+
+ vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_rgmii_pins>;
+ pinctrl-names = "default";
+
+ phy-handle = <ð_phy0>;
+ phy-mode = "rgmii";
+
+ amlogic,tx-delay-ns = <2>;
+
+ snps,reset-gpio = <&gpio GPIOZ_14 0>;
+ snps,reset-delays-us = <0 10000 1000000>;
+ snps,reset-active-low;
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ eth_phy0: ethernet-phy at 0 {
+ /* Realtek RTL8211F (0x001cc916) */
+ reg = <0>;
+ interrupt-parent = <&gpio_intc>;
+ /* MAC_INTR on GPIOZ_15 */
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&pinctrl_aobus {
+ gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
+ "VCCK En", "CON1 Header Pin31",
+ "I2S Header Pin6", "IR In", "I2S Header Pin7",
+ "I2S Header Pin3", "I2S Header Pin4",
+ "I2S Header Pin5", "HDMI CEC", "SYS LED",
+ /* GPIO_TEST_N */
+ "";
+};
+
+&pinctrl_periphs {
+ gpio-line-names = /* Bank GPIOZ */
+ "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
+ "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
+ "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
+ "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
+ "Eth PHY nRESET", "Eth PHY Intc",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL",
+ "CON1 Header Pin33",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
+ "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
+ "eMMC Reset", "eMMC CMD",
+ "", "", "", "", "eMMC DS",
+ "", "",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "",
+ "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+ "VDDEE Regulator", "VCCK Regulator",
+ /* Bank GPIOY */
+ "CON1 Header Pin7", "CON1 Header Pin11",
+ "CON1 Header Pin13", "CON1 Header Pin15",
+ "CON1 Header Pin18", "CON1 Header Pin19",
+ "CON1 Header Pin22", "CON1 Header Pin21",
+ "CON1 Header Pin24", "CON1 Header Pin23",
+ "CON1 Header Pin26", "CON1 Header Pin29",
+ "CON1 Header Pin32", "CON1 Header Pin8",
+ "CON1 Header Pin10", "CON1 Header Pin16",
+ "CON1 Header Pin12",
+ /* Bank GPIOX */
+ "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+ "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+ "WIFI Power Enable", "WIFI WAKE HOST",
+ "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+ "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+ "Bluetooth UART TX", "Bluetooth UART RX",
+ "Bluetooth UART CTS", "Bluetooth UART RTS",
+ "", "", "", "WIFI 32K", "Bluetooth Enable",
+ "Bluetooth WAKE HOST", "",
+ /* Bank GPIOCLK */
+ "", "CON1 Header Pin35", "", "";
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao18>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <200000000>;
+
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddio_ao3v3>;
+ vqmmc-supply = <&vddio_ao18>;
+
+ brcmf: wifi at 1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+ };
+};
+
+/* SD */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+
+ vmmc-supply = <&vddio_ao3v3>;
+ vqmmc-supply = <&vddio_tf>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "disabled";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc3v3>;
+ vqmmc-supply = <&vcc1v8>;
+};
+
+/* DBG_UART */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* Bluetooth on AP6212 */
+&uart_A {
+ status = "disabled";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+};
+
+/* 40-pin CON1 */
+&uart_C {
+ status = "disabled";
+ pinctrl-0 = <&uart_c_pins>;
+ pinctrl-names = "default";
+};
+
+&usb0_phy {
+ status = "okay";
+ phy-supply = <&vdd_5v>;
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH u-boot 1/2] ARM: dts: sync meson-gxbb-nanopi-k2 from Linux 4.17
@ 2018-06-25 14:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2018-06-25 14:50 UTC (permalink / raw)
To: linus-amlogic
Get the meson-gxbb-nanopi-k2.dts file from Linux 4.17.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/meson-gxbb-nanopi-k2.dts | 323 ++++++++++++++++++++++++++++++++++
2 files changed, 324 insertions(+)
create mode 100644 arch/arm/dts/meson-gxbb-nanopi-k2.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 493652e..bcbaae2 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -53,6 +53,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3399-puma-ddr1866.dtb \
rv1108-evb.dtb
dtb-$(CONFIG_ARCH_MESON) += \
+ meson-gxbb-nanopi-k2.dtb \
meson-gxbb-odroidc2.dtb \
meson-gxl-s905x-p212.dtb \
meson-gxl-s905x-libretech-cc.dtb \
diff --git a/arch/arm/dts/meson-gxbb-nanopi-k2.dts b/arch/arm/dts/meson-gxbb-nanopi-k2.dts
new file mode 100644
index 0000000..7d5709c
--- /dev/null
+++ b/arch/arm/dts/meson-gxbb-nanopi-k2.dts
@@ -0,0 +1,323 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas F?rber
+ */
+
+/dts-v1/;
+
+#include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
+
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ stat {
+ label = "nanopi-k2:blue:stat";
+ gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ panic-indicator;
+ };
+ };
+
+ vdd_5v: regulator-vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vddio_ao18: regulator-vddio-ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddio_ao3v3: regulator-vddio-ao3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vddio_tf: regulator-vddio-tf {
+ compatible = "regulator-gpio";
+
+ regulator-name = "VDDIO_TF";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0>,
+ <1800000 1>;
+
+ regulator-settling-time-up-us = <100>;
+ regulator-settling-time-down-us = <5000>;
+ };
+
+ wifi_32k: wifi-32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi_32k>;
+ clock-names = "ext_clock";
+ };
+
+ vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_rgmii_pins>;
+ pinctrl-names = "default";
+
+ phy-handle = <ð_phy0>;
+ phy-mode = "rgmii";
+
+ amlogic,tx-delay-ns = <2>;
+
+ snps,reset-gpio = <&gpio GPIOZ_14 0>;
+ snps,reset-delays-us = <0 10000 1000000>;
+ snps,reset-active-low;
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ eth_phy0: ethernet-phy at 0 {
+ /* Realtek RTL8211F (0x001cc916) */
+ reg = <0>;
+ interrupt-parent = <&gpio_intc>;
+ /* MAC_INTR on GPIOZ_15 */
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&pinctrl_aobus {
+ gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
+ "VCCK En", "CON1 Header Pin31",
+ "I2S Header Pin6", "IR In", "I2S Header Pin7",
+ "I2S Header Pin3", "I2S Header Pin4",
+ "I2S Header Pin5", "HDMI CEC", "SYS LED",
+ /* GPIO_TEST_N */
+ "";
+};
+
+&pinctrl_periphs {
+ gpio-line-names = /* Bank GPIOZ */
+ "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
+ "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
+ "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
+ "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
+ "Eth PHY nRESET", "Eth PHY Intc",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL",
+ "CON1 Header Pin33",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
+ "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
+ "eMMC Reset", "eMMC CMD",
+ "", "", "", "", "eMMC DS",
+ "", "",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "",
+ "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+ "VDDEE Regulator", "VCCK Regulator",
+ /* Bank GPIOY */
+ "CON1 Header Pin7", "CON1 Header Pin11",
+ "CON1 Header Pin13", "CON1 Header Pin15",
+ "CON1 Header Pin18", "CON1 Header Pin19",
+ "CON1 Header Pin22", "CON1 Header Pin21",
+ "CON1 Header Pin24", "CON1 Header Pin23",
+ "CON1 Header Pin26", "CON1 Header Pin29",
+ "CON1 Header Pin32", "CON1 Header Pin8",
+ "CON1 Header Pin10", "CON1 Header Pin16",
+ "CON1 Header Pin12",
+ /* Bank GPIOX */
+ "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+ "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+ "WIFI Power Enable", "WIFI WAKE HOST",
+ "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+ "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+ "Bluetooth UART TX", "Bluetooth UART RX",
+ "Bluetooth UART CTS", "Bluetooth UART RTS",
+ "", "", "", "WIFI 32K", "Bluetooth Enable",
+ "Bluetooth WAKE HOST", "",
+ /* Bank GPIOCLK */
+ "", "CON1 Header Pin35", "", "";
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao18>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <200000000>;
+
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddio_ao3v3>;
+ vqmmc-supply = <&vddio_ao18>;
+
+ brcmf: wifi at 1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+ };
+};
+
+/* SD */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+
+ vmmc-supply = <&vddio_ao3v3>;
+ vqmmc-supply = <&vddio_tf>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "disabled";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc3v3>;
+ vqmmc-supply = <&vcc1v8>;
+};
+
+/* DBG_UART */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* Bluetooth on AP6212 */
+&uart_A {
+ status = "disabled";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+};
+
+/* 40-pin CON1 */
+&uart_C {
+ status = "disabled";
+ pinctrl-0 = <&uart_c_pins>;
+ pinctrl-names = "default";
+};
+
+&usb0_phy {
+ status = "okay";
+ phy-supply = <&vdd_5v>;
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH u-boot 2/2] boards: amlogic: Add FriendlyElec NanoPi K2 board support
2018-06-25 14:50 ` Neil Armstrong
@ 2018-06-25 14:50 ` Neil Armstrong
-1 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2018-06-25 14:50 UTC (permalink / raw)
To: u-boot
From: Thomas McKahan <tonymckahan@gmail.com>
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/mach-meson/Kconfig | 8 +++
board/amlogic/nanopi-k2/Kconfig | 12 +++++
board/amlogic/nanopi-k2/MAINTAINERS | 6 +++
board/amlogic/nanopi-k2/Makefile | 7 +++
board/amlogic/nanopi-k2/README | 99 +++++++++++++++++++++++++++++++++++++
board/amlogic/nanopi-k2/nanopi-k2.c | 61 +++++++++++++++++++++++
configs/nanopi-k2_defconfig | 40 +++++++++++++++
include/configs/nanopi-k2.h | 18 +++++++
9 files changed, 252 insertions(+)
create mode 100644 board/amlogic/nanopi-k2/Kconfig
create mode 100644 board/amlogic/nanopi-k2/MAINTAINERS
create mode 100644 board/amlogic/nanopi-k2/Makefile
create mode 100644 board/amlogic/nanopi-k2/README
create mode 100644 board/amlogic/nanopi-k2/nanopi-k2.c
create mode 100644 configs/nanopi-k2_defconfig
create mode 100644 include/configs/nanopi-k2.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index bcbaae2..62fc442 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -55,6 +55,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
dtb-$(CONFIG_ARCH_MESON) += \
meson-gxbb-nanopi-k2.dtb \
meson-gxbb-odroidc2.dtb \
+ meson-gxbb-nanopi-k2.dtb \
meson-gxl-s905x-p212.dtb \
meson-gxl-s905x-libretech-cc.dtb \
meson-gxl-s905x-khadas-vim.dtb
diff --git a/arch/arm/mach-meson/Kconfig b/arch/arm/mach-meson/Kconfig
index 9a06ccc..cc3383a 100644
--- a/arch/arm/mach-meson/Kconfig
+++ b/arch/arm/mach-meson/Kconfig
@@ -29,6 +29,12 @@ config TARGET_ODROID_C2
with 2 GiB of RAM, Gigabit Ethernet, HDMI, 4 USB, micro-SD
slot, eMMC, IR receiver and a 40-pin GPIO header.
+config TARGET_NANOPI_K2
+ bool "NANOPI_K2"
+ help
+ NANOPI_K2 is a single board computer based on Meson GXBaby
+ with 2 GiB of RAM, Gigabit Ethernet,AP6212 Wifi, HDMI, 4 USB,
+ micro-SD slot, eMMC, IR receiver and a 40-pin GPIO header.
endif
if MESON_GXL
@@ -64,6 +70,8 @@ config SYS_MALLOC_F_LEN
source "board/amlogic/odroid-c2/Kconfig"
+source "board/amlogic/nanopi-k2/Kconfig"
+
source "board/amlogic/p212/Kconfig"
source "board/amlogic/libretech-cc/Kconfig"
diff --git a/board/amlogic/nanopi-k2/Kconfig b/board/amlogic/nanopi-k2/Kconfig
new file mode 100644
index 0000000..374bda2
--- /dev/null
+++ b/board/amlogic/nanopi-k2/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_NANOPI_K2
+
+config SYS_BOARD
+ default "nanopi-k2"
+
+config SYS_VENDOR
+ default "amlogic"
+
+config SYS_CONFIG_NAME
+ default "nanopi-k2"
+
+endif
diff --git a/board/amlogic/nanopi-k2/MAINTAINERS b/board/amlogic/nanopi-k2/MAINTAINERS
new file mode 100644
index 0000000..0452bd1
--- /dev/null
+++ b/board/amlogic/nanopi-k2/MAINTAINERS
@@ -0,0 +1,6 @@
+NANOPI-K2
+M: Neil Armstrong <narmstrong@baylibre.com>
+S: Maintained
+F: board/amlogic/nanopi-k2/
+F: include/configs/nanopi-k2.h
+F: configs/nanopi-k2_defconfig
diff --git a/board/amlogic/nanopi-k2/Makefile b/board/amlogic/nanopi-k2/Makefile
new file mode 100644
index 0000000..7d9b666
--- /dev/null
+++ b/board/amlogic/nanopi-k2/Makefile
@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2018 Thomas McKahan
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := nanopi-k2.o
diff --git a/board/amlogic/nanopi-k2/README b/board/amlogic/nanopi-k2/README
new file mode 100644
index 0000000..d450d3c
--- /dev/null
+++ b/board/amlogic/nanopi-k2/README
@@ -0,0 +1,99 @@
+U-Boot for NanoPi-K2
+====================
+
+NanoPi-K2 is a single board computer manufactured by FriendlyElec
+with the following specifications:
+
+ - Amlogic S905 ARM Cortex-A53 quad-core SoC @ 1.5GHz
+ - ARM Mali 450 GPU
+ - 2GB DDR3 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 40-pin GPIO header
+ - 4 x USB 2.0 Host, 1 x USB OTG
+ - eMMC, microSD
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make nanopi-k2_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b libretech-cc amlogic-u-boot
+ > git clone https://github.com/friendlyarm/u-boot.git -b nanopi-k2-v2015.01 amlogic-u-boot
+ > cd amlogic-u-boot
+ > sed -i 's/aarch64-linux-gnu-/aarch64-none-elf-/' Makefile
+ > sed -i 's/arm-linux-/arm-none-eabi-/' arch/arm/cpu/armv8/gxb/firmware/scp_task/Makefile
+ > make nanopi-k2_defconfig
+ > make
+ > export FIPDIR=$PWD/fip
+
+Go back to mainline U-Boot source tree then :
+ > mkdir fip
+
+ > cp $FIPDIR/gxb/bl2.bin fip/
+ > cp $FIPDIR/gxb/acs.bin fip/
+ > cp $FIPDIR/gxb/bl21.bin fip/
+ > cp $FIPDIR/gxb/bl30.bin fip/
+ > cp $FIPDIR/gxb/bl301.bin fip/
+ > cp $FIPDIR/gxb/bl31.img fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl30.bin \
+ fip/zero_tmp \
+ fip/bl30_zero.bin \
+ fip/bl301.bin \
+ fip/bl301_zero.bin \
+ fip/bl30_new.bin \
+ bl30
+
+ > $FIPDIR/fip_create \
+ --bl30 fip/bl30_new.bin \
+ --bl31 fip/bl31.img \
+ --bl33 fip/bl33.bin \
+ fip/fip.bin
+
+ > python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl2_acs.bin \
+ fip/zero_tmp \
+ fip/bl2_zero.bin \
+ fip/bl21.bin \
+ fip/bl21_zero.bin \
+ fip/bl2_new.bin \
+ bl2
+
+ > cat fip/bl2_new.bin fip/fip.bin > fip/boot_new.bin
+
+ > $FIPDIR/gxb/aml_encrypt_gxb --bootsig \
+ --input fip/boot_new.bin
+ --output fip/u-boot.bin
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin of=$DEV conv=fsync,notrunc bs=512 seek=1
diff --git a/board/amlogic/nanopi-k2/nanopi-k2.c b/board/amlogic/nanopi-k2/nanopi-k2.c
new file mode 100644
index 0000000..339dbb8
--- /dev/null
+++ b/board/amlogic/nanopi-k2/nanopi-k2.c
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2018 Thomas McKahan
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <environment.h>
+#include <asm/io.h>
+#include <asm/arch/gx.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+#include <asm/arch/mem.h>
+
+#define EFUSE_SN_OFFSET 20
+#define EFUSE_SN_SIZE 16
+#define EFUSE_MAC_OFFSET 52
+#define EFUSE_MAC_SIZE 6
+
+int board_init(void)
+{
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ u8 mac_addr[EFUSE_MAC_SIZE];
+ char serial[EFUSE_SN_SIZE];
+ ssize_t len;
+
+ meson_gx_eth_init(PHY_INTERFACE_MODE_RGMII, 0);
+
+ /* Reset PHY on GPIOZ_14 */
+ clrbits_le32(GX_GPIO_EN(3), BIT(14));
+ clrbits_le32(GX_GPIO_OUT(3), BIT(14));
+ mdelay(10);
+ setbits_le32(GX_GPIO_OUT(3), BIT(14));
+
+ if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+ len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+ mac_addr, EFUSE_MAC_SIZE);
+ if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr))
+ eth_env_set_enetaddr("ethaddr", mac_addr);
+ }
+
+ if (!env_get("serial#")) {
+ len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+ EFUSE_SN_SIZE);
+ if (len == EFUSE_SN_SIZE)
+ env_set("serial#", serial);
+ }
+
+ return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ meson_gx_init_reserved_memory(blob);
+
+ return 0;
+}
diff --git a/configs/nanopi-k2_defconfig b/configs/nanopi-k2_defconfig
new file mode 100644
index 0000000..8a0dbf0
--- /dev/null
+++ b/configs/nanopi-k2_defconfig
@@ -0,0 +1,40 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_MESON_GXBB=y
+CONFIG_TARGET_NANOPI_K2=y
+CONFIG_DEBUG_UART_BASE=0xc81004c0
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" nanopi-k2"
+CONFIG_DEFAULT_DEVICE_TREE="meson-gxbb-nanopi-k2"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MESON=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_GXBB=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/include/configs/nanopi-k2.h b/include/configs/nanopi-k2.h
new file mode 100644
index 0000000..f7ecb7b
--- /dev/null
+++ b/include/configs/nanopi-k2.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration for NANOPI-K2
+ * (C) Copyright 2018 Thomas McKahan
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MISC_INIT_R
+
+/* Serial setup */
+
+#define MESON_FDTFILE_SETTING "fdtfile=amlogic/meson-gxbb-nanopi-k2.dtb\0"
+
+#include <configs/meson-gx-common.h>
+
+#endif /* __CONFIG_H */
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH u-boot 2/2] boards: amlogic: Add FriendlyElec NanoPi K2 board support
@ 2018-06-25 14:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2018-06-25 14:50 UTC (permalink / raw)
To: linus-amlogic
From: Thomas McKahan <tonymckahan@gmail.com>
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/mach-meson/Kconfig | 8 +++
board/amlogic/nanopi-k2/Kconfig | 12 +++++
board/amlogic/nanopi-k2/MAINTAINERS | 6 +++
board/amlogic/nanopi-k2/Makefile | 7 +++
board/amlogic/nanopi-k2/README | 99 +++++++++++++++++++++++++++++++++++++
board/amlogic/nanopi-k2/nanopi-k2.c | 61 +++++++++++++++++++++++
configs/nanopi-k2_defconfig | 40 +++++++++++++++
include/configs/nanopi-k2.h | 18 +++++++
9 files changed, 252 insertions(+)
create mode 100644 board/amlogic/nanopi-k2/Kconfig
create mode 100644 board/amlogic/nanopi-k2/MAINTAINERS
create mode 100644 board/amlogic/nanopi-k2/Makefile
create mode 100644 board/amlogic/nanopi-k2/README
create mode 100644 board/amlogic/nanopi-k2/nanopi-k2.c
create mode 100644 configs/nanopi-k2_defconfig
create mode 100644 include/configs/nanopi-k2.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index bcbaae2..62fc442 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -55,6 +55,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
dtb-$(CONFIG_ARCH_MESON) += \
meson-gxbb-nanopi-k2.dtb \
meson-gxbb-odroidc2.dtb \
+ meson-gxbb-nanopi-k2.dtb \
meson-gxl-s905x-p212.dtb \
meson-gxl-s905x-libretech-cc.dtb \
meson-gxl-s905x-khadas-vim.dtb
diff --git a/arch/arm/mach-meson/Kconfig b/arch/arm/mach-meson/Kconfig
index 9a06ccc..cc3383a 100644
--- a/arch/arm/mach-meson/Kconfig
+++ b/arch/arm/mach-meson/Kconfig
@@ -29,6 +29,12 @@ config TARGET_ODROID_C2
with 2 GiB of RAM, Gigabit Ethernet, HDMI, 4 USB, micro-SD
slot, eMMC, IR receiver and a 40-pin GPIO header.
+config TARGET_NANOPI_K2
+ bool "NANOPI_K2"
+ help
+ NANOPI_K2 is a single board computer based on Meson GXBaby
+ with 2 GiB of RAM, Gigabit Ethernet,AP6212 Wifi, HDMI, 4 USB,
+ micro-SD slot, eMMC, IR receiver and a 40-pin GPIO header.
endif
if MESON_GXL
@@ -64,6 +70,8 @@ config SYS_MALLOC_F_LEN
source "board/amlogic/odroid-c2/Kconfig"
+source "board/amlogic/nanopi-k2/Kconfig"
+
source "board/amlogic/p212/Kconfig"
source "board/amlogic/libretech-cc/Kconfig"
diff --git a/board/amlogic/nanopi-k2/Kconfig b/board/amlogic/nanopi-k2/Kconfig
new file mode 100644
index 0000000..374bda2
--- /dev/null
+++ b/board/amlogic/nanopi-k2/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_NANOPI_K2
+
+config SYS_BOARD
+ default "nanopi-k2"
+
+config SYS_VENDOR
+ default "amlogic"
+
+config SYS_CONFIG_NAME
+ default "nanopi-k2"
+
+endif
diff --git a/board/amlogic/nanopi-k2/MAINTAINERS b/board/amlogic/nanopi-k2/MAINTAINERS
new file mode 100644
index 0000000..0452bd1
--- /dev/null
+++ b/board/amlogic/nanopi-k2/MAINTAINERS
@@ -0,0 +1,6 @@
+NANOPI-K2
+M: Neil Armstrong <narmstrong@baylibre.com>
+S: Maintained
+F: board/amlogic/nanopi-k2/
+F: include/configs/nanopi-k2.h
+F: configs/nanopi-k2_defconfig
diff --git a/board/amlogic/nanopi-k2/Makefile b/board/amlogic/nanopi-k2/Makefile
new file mode 100644
index 0000000..7d9b666
--- /dev/null
+++ b/board/amlogic/nanopi-k2/Makefile
@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2018 Thomas McKahan
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := nanopi-k2.o
diff --git a/board/amlogic/nanopi-k2/README b/board/amlogic/nanopi-k2/README
new file mode 100644
index 0000000..d450d3c
--- /dev/null
+++ b/board/amlogic/nanopi-k2/README
@@ -0,0 +1,99 @@
+U-Boot for NanoPi-K2
+====================
+
+NanoPi-K2 is a single board computer manufactured by FriendlyElec
+with the following specifications:
+
+ - Amlogic S905 ARM Cortex-A53 quad-core SoC @ 1.5GHz
+ - ARM Mali 450 GPU
+ - 2GB DDR3 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 40-pin GPIO header
+ - 4 x USB 2.0 Host, 1 x USB OTG
+ - eMMC, microSD
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make nanopi-k2_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b libretech-cc amlogic-u-boot
+ > git clone https://github.com/friendlyarm/u-boot.git -b nanopi-k2-v2015.01 amlogic-u-boot
+ > cd amlogic-u-boot
+ > sed -i 's/aarch64-linux-gnu-/aarch64-none-elf-/' Makefile
+ > sed -i 's/arm-linux-/arm-none-eabi-/' arch/arm/cpu/armv8/gxb/firmware/scp_task/Makefile
+ > make nanopi-k2_defconfig
+ > make
+ > export FIPDIR=$PWD/fip
+
+Go back to mainline U-Boot source tree then :
+ > mkdir fip
+
+ > cp $FIPDIR/gxb/bl2.bin fip/
+ > cp $FIPDIR/gxb/acs.bin fip/
+ > cp $FIPDIR/gxb/bl21.bin fip/
+ > cp $FIPDIR/gxb/bl30.bin fip/
+ > cp $FIPDIR/gxb/bl301.bin fip/
+ > cp $FIPDIR/gxb/bl31.img fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl30.bin \
+ fip/zero_tmp \
+ fip/bl30_zero.bin \
+ fip/bl301.bin \
+ fip/bl301_zero.bin \
+ fip/bl30_new.bin \
+ bl30
+
+ > $FIPDIR/fip_create \
+ --bl30 fip/bl30_new.bin \
+ --bl31 fip/bl31.img \
+ --bl33 fip/bl33.bin \
+ fip/fip.bin
+
+ > python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl2_acs.bin \
+ fip/zero_tmp \
+ fip/bl2_zero.bin \
+ fip/bl21.bin \
+ fip/bl21_zero.bin \
+ fip/bl2_new.bin \
+ bl2
+
+ > cat fip/bl2_new.bin fip/fip.bin > fip/boot_new.bin
+
+ > $FIPDIR/gxb/aml_encrypt_gxb --bootsig \
+ --input fip/boot_new.bin
+ --output fip/u-boot.bin
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin of=$DEV conv=fsync,notrunc bs=512 seek=1
diff --git a/board/amlogic/nanopi-k2/nanopi-k2.c b/board/amlogic/nanopi-k2/nanopi-k2.c
new file mode 100644
index 0000000..339dbb8
--- /dev/null
+++ b/board/amlogic/nanopi-k2/nanopi-k2.c
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2018 Thomas McKahan
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <environment.h>
+#include <asm/io.h>
+#include <asm/arch/gx.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+#include <asm/arch/mem.h>
+
+#define EFUSE_SN_OFFSET 20
+#define EFUSE_SN_SIZE 16
+#define EFUSE_MAC_OFFSET 52
+#define EFUSE_MAC_SIZE 6
+
+int board_init(void)
+{
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ u8 mac_addr[EFUSE_MAC_SIZE];
+ char serial[EFUSE_SN_SIZE];
+ ssize_t len;
+
+ meson_gx_eth_init(PHY_INTERFACE_MODE_RGMII, 0);
+
+ /* Reset PHY on GPIOZ_14 */
+ clrbits_le32(GX_GPIO_EN(3), BIT(14));
+ clrbits_le32(GX_GPIO_OUT(3), BIT(14));
+ mdelay(10);
+ setbits_le32(GX_GPIO_OUT(3), BIT(14));
+
+ if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+ len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+ mac_addr, EFUSE_MAC_SIZE);
+ if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr))
+ eth_env_set_enetaddr("ethaddr", mac_addr);
+ }
+
+ if (!env_get("serial#")) {
+ len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+ EFUSE_SN_SIZE);
+ if (len == EFUSE_SN_SIZE)
+ env_set("serial#", serial);
+ }
+
+ return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ meson_gx_init_reserved_memory(blob);
+
+ return 0;
+}
diff --git a/configs/nanopi-k2_defconfig b/configs/nanopi-k2_defconfig
new file mode 100644
index 0000000..8a0dbf0
--- /dev/null
+++ b/configs/nanopi-k2_defconfig
@@ -0,0 +1,40 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_MESON_GXBB=y
+CONFIG_TARGET_NANOPI_K2=y
+CONFIG_DEBUG_UART_BASE=0xc81004c0
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" nanopi-k2"
+CONFIG_DEFAULT_DEVICE_TREE="meson-gxbb-nanopi-k2"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MESON=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_GXBB=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/include/configs/nanopi-k2.h b/include/configs/nanopi-k2.h
new file mode 100644
index 0000000..f7ecb7b
--- /dev/null
+++ b/include/configs/nanopi-k2.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration for NANOPI-K2
+ * (C) Copyright 2018 Thomas McKahan
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MISC_INIT_R
+
+/* Serial setup */
+
+#define MESON_FDTFILE_SETTING "fdtfile=amlogic/meson-gxbb-nanopi-k2.dtb\0"
+
+#include <configs/meson-gx-common.h>
+
+#endif /* __CONFIG_H */
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [U-Boot, u-boot, 1/2] ARM: dts: sync meson-gxbb-nanopi-k2 from Linux 4.17
2018-06-25 14:50 ` Neil Armstrong
@ 2018-07-20 12:35 ` Tom Rini
-1 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2018-07-20 12:35 UTC (permalink / raw)
To: u-boot
On Mon, Jun 25, 2018 at 04:50:16PM +0200, Neil Armstrong wrote:
> Get the meson-gxbb-nanopi-k2.dts file from Linux 4.17.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180720/5d0c1b1b/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot, u-boot, 1/2] ARM: dts: sync meson-gxbb-nanopi-k2 from Linux 4.17
@ 2018-07-20 12:35 ` Tom Rini
0 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2018-07-20 12:35 UTC (permalink / raw)
To: linus-amlogic
On Mon, Jun 25, 2018 at 04:50:16PM +0200, Neil Armstrong wrote:
> Get the meson-gxbb-nanopi-k2.dts file from Linux 4.17.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-amlogic/attachments/20180720/5d0c1b1b/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [U-Boot, u-boot, 2/2] boards: amlogic: Add FriendlyElec NanoPi K2 board support
2018-06-25 14:50 ` Neil Armstrong
@ 2018-07-20 12:35 ` Tom Rini
-1 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2018-07-20 12:35 UTC (permalink / raw)
To: u-boot
On Mon, Jun 25, 2018 at 04:50:17PM +0200, Neil Armstrong wrote:
> From: Thomas McKahan <tonymckahan@gmail.com>
>
> This adds platform code for the FriendlyElec NanoPi K2 board based on a
> Meson GXBB (S905) SoC with the Meson GXBB configuration.
>
> This initial submission only supports:
> - UART
> - MMC/SDCard
> - Ethernet
> - Reset Controller
> - Clock controller
>
> Cc: Yuefei Tan <yftan@friendlyarm.com>
> Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Applied to u-boot/master, thanks! But please note:
CHECK: Alignment should match open parenthesis
#277: FILE: board/amlogic/nanopi-k2/nanopi-k2.c:48:
+ len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+ EFUSE_SN_SIZE);
A follow-up when you're in these files next would be appreciated,
thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180720/2bb67800/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot, u-boot, 2/2] boards: amlogic: Add FriendlyElec NanoPi K2 board support
@ 2018-07-20 12:35 ` Tom Rini
0 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2018-07-20 12:35 UTC (permalink / raw)
To: linus-amlogic
On Mon, Jun 25, 2018 at 04:50:17PM +0200, Neil Armstrong wrote:
> From: Thomas McKahan <tonymckahan@gmail.com>
>
> This adds platform code for the FriendlyElec NanoPi K2 board based on a
> Meson GXBB (S905) SoC with the Meson GXBB configuration.
>
> This initial submission only supports:
> - UART
> - MMC/SDCard
> - Ethernet
> - Reset Controller
> - Clock controller
>
> Cc: Yuefei Tan <yftan@friendlyarm.com>
> Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Applied to u-boot/master, thanks! But please note:
CHECK: Alignment should match open parenthesis
#277: FILE: board/amlogic/nanopi-k2/nanopi-k2.c:48:
+ len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+ EFUSE_SN_SIZE);
A follow-up when you're in these files next would be appreciated,
thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-amlogic/attachments/20180720/2bb67800/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [U-Boot, u-boot, 2/2] boards: amlogic: Add FriendlyElec NanoPi K2 board support
2018-07-20 12:35 ` Tom Rini
@ 2018-07-20 12:59 ` Neil Armstrong
-1 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2018-07-20 12:59 UTC (permalink / raw)
To: u-boot
Hi Tom,
On 20/07/2018 14:35, Tom Rini wrote:
> On Mon, Jun 25, 2018 at 04:50:17PM +0200, Neil Armstrong wrote:
>
>> From: Thomas McKahan <tonymckahan@gmail.com>
>>
>> This adds platform code for the FriendlyElec NanoPi K2 board based on a
>> Meson GXBB (S905) SoC with the Meson GXBB configuration.
>>
>> This initial submission only supports:
>> - UART
>> - MMC/SDCard
>> - Ethernet
>> - Reset Controller
>> - Clock controller
>>
>> Cc: Yuefei Tan <yftan@friendlyarm.com>
>> Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>
> Applied to u-boot/master, thanks! But please note:
> CHECK: Alignment should match open parenthesis
> #277: FILE: board/amlogic/nanopi-k2/nanopi-k2.c:48:
> + len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
> + EFUSE_SN_SIZE);
>
> A follow-up when you're in these files next would be appreciated,
> thanks!
>
Ok, I need to do a cleanup of all these boards anyway, will fix this in the same time.
thanks,
Neil
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180720/0bb6223c/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot, u-boot, 2/2] boards: amlogic: Add FriendlyElec NanoPi K2 board support
@ 2018-07-20 12:59 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2018-07-20 12:59 UTC (permalink / raw)
To: linus-amlogic
Hi Tom,
On 20/07/2018 14:35, Tom Rini wrote:
> On Mon, Jun 25, 2018 at 04:50:17PM +0200, Neil Armstrong wrote:
>
>> From: Thomas McKahan <tonymckahan@gmail.com>
>>
>> This adds platform code for the FriendlyElec NanoPi K2 board based on a
>> Meson GXBB (S905) SoC with the Meson GXBB configuration.
>>
>> This initial submission only supports:
>> - UART
>> - MMC/SDCard
>> - Ethernet
>> - Reset Controller
>> - Clock controller
>>
>> Cc: Yuefei Tan <yftan@friendlyarm.com>
>> Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>
> Applied to u-boot/master, thanks! But please note:
> CHECK: Alignment should match open parenthesis
> #277: FILE: board/amlogic/nanopi-k2/nanopi-k2.c:48:
> + len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
> + EFUSE_SN_SIZE);
>
> A follow-up when you're in these files next would be appreciated,
> thanks!
>
Ok, I need to do a cleanup of all these boards anyway, will fix this in the same time.
thanks,
Neil
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-amlogic/attachments/20180720/0bb6223c/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2018-07-20 12:59 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-06-25 14:50 [U-Boot] [PATCH u-boot 0/2] Add support for the FriendlyElec NanoPi K2 board Neil Armstrong
2018-06-25 14:50 ` Neil Armstrong
2018-06-25 14:50 ` [U-Boot] [PATCH u-boot 1/2] ARM: dts: sync meson-gxbb-nanopi-k2 from Linux 4.17 Neil Armstrong
2018-06-25 14:50 ` Neil Armstrong
2018-07-20 12:35 ` [U-Boot] [U-Boot, u-boot, " Tom Rini
2018-07-20 12:35 ` Tom Rini
2018-06-25 14:50 ` [U-Boot] [PATCH u-boot 2/2] boards: amlogic: Add FriendlyElec NanoPi K2 board support Neil Armstrong
2018-06-25 14:50 ` Neil Armstrong
2018-07-20 12:35 ` [U-Boot] [U-Boot, u-boot, " Tom Rini
2018-07-20 12:35 ` Tom Rini
2018-07-20 12:59 ` [U-Boot] " Neil Armstrong
2018-07-20 12:59 ` Neil Armstrong
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.