[PATCH v3 0/4] serial: sh-sci: Clean up previous RZ/A2 support

[PATCH v3 0/4] serial: sh-sci: Clean up previous RZ/A2 support

[Chris Brandt]

This patch series doesn't really provide much new functionality, but
rather provides a cleaner solution for adding RZ/A2 support.

This series applies on top of tty-next

v3:
* removed a line of code that wasn't needed
v2:
* Incorporated feedback from Geert
* Added Reviewed-by

Chris Brandt (4):
  serial: sh-sci: Improve interrupts description
  serial: sh-sci: Allow for compressed SCIF address
  serial: sh-sci: Remove SCIx_RZ_SCIFA_REGTYPE
  serial: sh-sci: Improve support for separate TEI and DRI interrupts

 .../bindings/serial/renesas,sci-serial.txt         |  16 ++-
 drivers/tty/serial/sh-sci.c                        | 147 ++++++++-------------
 include/linux/serial_sci.h                         |   1 -
 3 files changed, 70 insertions(+), 94 deletions(-)

-- 
2.16.1

[PATCH v3 1/4] serial: sh-sci: Improve interrupts description

[Chris Brandt]

Describe interrupts property in more detail, especially when there are
more than one interrupt.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 .../devicetree/bindings/serial/renesas,sci-serial.txt    | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
index a7cda6550100..eaca9da79d83 100644
--- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
+++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
@@ -73,7 +73,21 @@ Required properties:
     family-specific and/or generic versions.
 
   - reg: Base address and length of the I/O registers used by the UART.
-  - interrupts: Must contain an interrupt-specifier for the SCIx interrupt.
+  - interrupts: Must contain one or more interrupt-specifiers for the SCIx.
+                If a single interrupt is expressed, then all events are
+                multiplexed into this single interrupt.
+
+                If multiple interrupts are provided by the hardware, the order
+                in which the interrupts are listed must match order below. Note
+                that some HW interrupt events may be muxed together resulting
+                in duplicate entries.
+                The interrupt order is as follows:
+                  1. Error (ERI)
+                  2. Receive buffer full (RXI)
+                  3. Transmit buffer empty (TXI)
+                  4. Break (BRI)
+                  5. Data Ready (DRI)
+                  6. Transmit End (TEI)
 
   - clocks: Must contain a phandle and clock-specifier pair for each entry
     in clock-names.
-- 
2.16.1

[PATCH v3 2/4] serial: sh-sci: Allow for compressed SCIF address

[Chris Brandt]

Some devices with SCIx_SH4_SCIF_REGTYPE have no space between registers.
Use the register area size to determine the spacing between register.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
---
v2:
* adjust for case of SCIx_PROBE_REGTYPE
---
 drivers/tty/serial/sh-sci.c | 25 +++++++++++++++----------
 1 file changed, 15 insertions(+), 10 deletions(-)

diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index 6ff6f2bf3b9b..c29244f76057 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -348,15 +348,15 @@ static const struct sci_port_params sci_port_params[SCIx_NR_REGTYPES] = {
 	[SCIx_SH4_SCIF_REGTYPE] = {
 		.regs = {
 			[SCSMR]		= { 0x00, 16 },
-			[SCBRR]		= { 0x04,  8 },
-			[SCSCR]		= { 0x08, 16 },
-			[SCxTDR]	= { 0x0c,  8 },
-			[SCxSR]		= { 0x10, 16 },
-			[SCxRDR]	= { 0x14,  8 },
-			[SCFCR]		= { 0x18, 16 },
-			[SCFDR]		= { 0x1c, 16 },
-			[SCSPTR]	= { 0x20, 16 },
-			[SCLSR]		= { 0x24, 16 },
+			[SCBRR]		= { 0x02,  8 },
+			[SCSCR]		= { 0x04, 16 },
+			[SCxTDR]	= { 0x06,  8 },
+			[SCxSR]		= { 0x08, 16 },
+			[SCxRDR]	= { 0x0a,  8 },
+			[SCFCR]		= { 0x0c, 16 },
+			[SCFDR]		= { 0x0e, 16 },
+			[SCSPTR]	= { 0x10, 16 },
+			[SCLSR]		= { 0x12, 16 },
 		},
 		.fifosize = 16,
 		.overrun_reg = SCLSR,
@@ -2848,7 +2848,7 @@ static int sci_init_single(struct platform_device *dev,
 {
 	struct uart_port *port = &sci_port->port;
 	const struct resource *res;
-	unsigned int i;
+	unsigned int i, regtype;
 	int ret;
 
 	sci_port->cfg	= p;
@@ -2885,6 +2885,7 @@ static int sci_init_single(struct platform_device *dev,
 	if (unlikely(sci_port->params == NULL))
 		return -EINVAL;
 
+	regtype = sci_port->params - sci_port_params;
 	switch (p->type) {
 	case PORT_SCIFB:
 		sci_port->rx_trigger = 48;
@@ -2939,6 +2940,10 @@ static int sci_init_single(struct platform_device *dev,
 			port->regshift = 1;
 	}
 
+	if (regtype == SCIx_SH4_SCIF_REGTYPE)
+		if (sci_port->reg_size >= 0x20)
+			port->regshift = 1;
+
 	/*
 	 * The UART port needs an IRQ value, so we peg this to the RX IRQ
 	 * for the multi-IRQ ports, which is where we are primarily
-- 
2.16.1

[PATCH v3 3/4] serial: sh-sci: Remove SCIx_RZ_SCIFA_REGTYPE

[Chris Brandt]

There is no more need for SCIx_RZ_SCIFA_REGTYPE now that
SCIx_SH4_SCIF_REGTYPE can provide the same register/address definitions.

Also, R7S9210 no longer needs a special compatible since the standard
"renesas,scif" will work just fine.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
v2:
* add Reviewed-by
---
 drivers/tty/serial/sh-sci.c | 31 -------------------------------
 include/linux/serial_sci.h  |  1 -
 2 files changed, 32 deletions(-)

diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index c29244f76057..54ea58bbe3c9 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -293,33 +293,6 @@ static const struct sci_port_params sci_port_params[SCIx_NR_REGTYPES] = {
 		.error_clear = SCIF_ERROR_CLEAR,
 	},
 
-	/*
-	 * The "SCIFA" that is in RZ/T and RZ/A2.
-	 * It looks like a normal SCIF with FIFO data, but with a
-	 * compressed address space. Also, the break out of interrupts
-	 * are different: ERI/BRI, RXI, TXI, TEI, DRI.
-	 */
-	[SCIx_RZ_SCIFA_REGTYPE] = {
-		.regs = {
-			[SCSMR]		= { 0x00, 16 },
-			[SCBRR]		= { 0x02,  8 },
-			[SCSCR]		= { 0x04, 16 },
-			[SCxTDR]	= { 0x06,  8 },
-			[SCxSR]		= { 0x08, 16 },
-			[SCxRDR]	= { 0x0A,  8 },
-			[SCFCR]		= { 0x0C, 16 },
-			[SCFDR]		= { 0x0E, 16 },
-			[SCSPTR]	= { 0x10, 16 },
-			[SCLSR]		= { 0x12, 16 },
-		},
-		.fifosize = 16,
-		.overrun_reg = SCLSR,
-		.overrun_mask = SCLSR_ORER,
-		.sampling_rate_mask = SCI_SR(32),
-		.error_mask = SCIF_DEFAULT_ERROR_MASK,
-		.error_clear = SCIF_ERROR_CLEAR,
-	},
-
 	/*
 	 * Common SH-3 SCIF definitions.
 	 */
@@ -3148,10 +3121,6 @@ static const struct of_device_id of_sci_match[] = {
 		.compatible = "renesas,scif-r7s72100",
 		.data = SCI_OF_DATA(PORT_SCIF, SCIx_SH2_SCIF_FIFODATA_REGTYPE),
 	},
-	{
-		.compatible = "renesas,scif-r7s9210",
-		.data = SCI_OF_DATA(PORT_SCIF, SCIx_RZ_SCIFA_REGTYPE),
-	},
 	/* Family-specific types */
 	{
 		.compatible = "renesas,rcar-gen1-scif",
diff --git a/include/linux/serial_sci.h b/include/linux/serial_sci.h
index 1c89611e0e06..c0e795d95477 100644
--- a/include/linux/serial_sci.h
+++ b/include/linux/serial_sci.h
@@ -36,7 +36,6 @@ enum {
 	SCIx_SH4_SCIF_FIFODATA_REGTYPE,
 	SCIx_SH7705_SCIF_REGTYPE,
 	SCIx_HSCIF_REGTYPE,
-	SCIx_RZ_SCIFA_REGTYPE,
 
 	SCIx_NR_REGTYPES,
 };
-- 
2.16.1

[PATCH v3 4/4] serial: sh-sci: Improve support for separate TEI and DRI interrupts

[Chris Brandt]

Some SCIF versions mux error and break interrupts together and then provide
a separate interrupt ID for just TEI/DRI.

Allow all 6 types of interrupts to be specified via platform data (or DT)
and for any signals that are muxed together (have the same interrupt
number) simply register one handler.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
v3:
* Setting string to NULL first is no longer needed
v2:
* Removed - 1 from loop
* Added Reviewed-by
---
 drivers/tty/serial/sh-sci.c | 91 ++++++++++++++++++++-------------------------
 1 file changed, 40 insertions(+), 51 deletions(-)

diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index 54ea58bbe3c9..ac4424bf6b13 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -65,7 +65,8 @@ enum {
 	SCIx_RXI_IRQ,
 	SCIx_TXI_IRQ,
 	SCIx_BRI_IRQ,
-	SCIx_TEIDRI_IRQ,
+	SCIx_DRI_IRQ,
+	SCIx_TEI_IRQ,
 	SCIx_NR_IRQS,
 
 	SCIx_MUX_IRQ = SCIx_NR_IRQS,	/* special case */
@@ -77,9 +78,6 @@ enum {
 	((port)->irqs[SCIx_ERI_IRQ] &&	\
 	 ((port)->irqs[SCIx_RXI_IRQ] < 0))
 
-#define SCIx_TEIDRI_IRQ_EXISTS(port)		\
-	((port)->irqs[SCIx_TEIDRI_IRQ] > 0)
-
 enum SCI_CLKS {
 	SCI_FCK,		/* Functional Clock */
 	SCI_SCK,		/* Optional External Clock */
@@ -1685,14 +1683,23 @@ static irqreturn_t sci_tx_interrupt(int irq, void *ptr)
 	return IRQ_HANDLED;
 }
 
-static irqreturn_t sci_br_interrupt(int irq, void *ptr);
+static irqreturn_t sci_br_interrupt(int irq, void *ptr)
+{
+	struct uart_port *port = ptr;
+
+	/* Handle BREAKs */
+	sci_handle_breaks(port);
+	sci_clear_SCxSR(port, SCxSR_BREAK_CLEAR(port));
+
+	return IRQ_HANDLED;
+}
 
 static irqreturn_t sci_er_interrupt(int irq, void *ptr)
 {
 	struct uart_port *port = ptr;
 	struct sci_port *s = to_sci_port(port);
 
-	if (SCIx_TEIDRI_IRQ_EXISTS(s)) {
+	if (s->irqs[SCIx_ERI_IRQ] == s->irqs[SCIx_BRI_IRQ]) {
 		/* Break and Error interrupts are muxed */
 		unsigned short ssr_status = serial_port_in(port, SCxSR);
 
@@ -1727,17 +1734,6 @@ static irqreturn_t sci_er_interrupt(int irq, void *ptr)
 	return IRQ_HANDLED;
 }
 
-static irqreturn_t sci_br_interrupt(int irq, void *ptr)
-{
-	struct uart_port *port = ptr;
-
-	/* Handle BREAKs */
-	sci_handle_breaks(port);
-	sci_clear_SCxSR(port, SCxSR_BREAK_CLEAR(port));
-
-	return IRQ_HANDLED;
-}
-
 static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr)
 {
 	unsigned short ssr_status, scr_status, err_enabled, orer_status = 0;
@@ -1811,6 +1807,16 @@ static const struct sci_irq_desc {
 		.handler = sci_br_interrupt,
 	},
 
+	[SCIx_DRI_IRQ] = {
+		.desc = "rx ready",
+		.handler = sci_rx_interrupt,
+	},
+
+	[SCIx_TEI_IRQ] = {
+		.desc = "tx end",
+		.handler = sci_tx_interrupt,
+	},
+
 	/*
 	 * Special muxed handler.
 	 */
@@ -1823,12 +1829,19 @@ static const struct sci_irq_desc {
 static int sci_request_irq(struct sci_port *port)
 {
 	struct uart_port *up = &port->port;
-	int i, j, ret = 0;
+	int i, j, w, ret = 0;
 
 	for (i = j = 0; i < SCIx_NR_IRQS; i++, j++) {
 		const struct sci_irq_desc *desc;
 		int irq;
 
+		/* Check if already registered (muxed) */
+		for (w = 0; w < i; w++)
+			if (port->irqs[w] == port->irqs[i])
+				w = i + 1;
+		if (w > i)
+			continue;
+
 		if (SCIx_IRQ_IS_MUXED(port)) {
 			i = SCIx_MUX_IRQ;
 			irq = up->irq;
@@ -1844,32 +1857,8 @@ static int sci_request_irq(struct sci_port *port)
 		}
 
 		desc = sci_irq_desc + i;
-		port->irqstr[j] = NULL;
-		if (SCIx_TEIDRI_IRQ_EXISTS(port)) {
-			/*
-			 * ERI and BRI are muxed, just register ERI and
-			 * ignore BRI.
-			 * TEI and DRI are muxed, but only DRI
-			 * is enabled, so use RXI handler
-			 */
-			if (i == SCIx_ERI_IRQ)
-				port->irqstr[j] = kasprintf(GFP_KERNEL,
-							    "%s:err + break",
-							    dev_name(up->dev));
-			if (i == SCIx_BRI_IRQ)
-				continue;
-			if (i == SCIx_TEIDRI_IRQ) {
-				port->irqstr[j] = kasprintf(GFP_KERNEL,
-							    "%s:tx end + rx ready",
-							    dev_name(up->dev));
-				desc = sci_irq_desc + SCIx_RXI_IRQ;
-			}
-		}
-
-		if (!port->irqstr[j])
-			port->irqstr[j] = kasprintf(GFP_KERNEL, "%s:%s",
-						    dev_name(up->dev),
-						    desc->desc);
+		port->irqstr[j] = kasprintf(GFP_KERNEL, "%s:%s",
+					    dev_name(up->dev), desc->desc);
 		if (!port->irqstr[j]) {
 			ret = -ENOMEM;
 			goto out_nomem;
@@ -2842,17 +2831,17 @@ static int sci_init_single(struct platform_device *dev,
 
 	/* The SCI generates several interrupts. They can be muxed together or
 	 * connected to different interrupt lines. In the muxed case only one
-	 * interrupt resource is specified. In the non-muxed case three or four
-	 * interrupt resources are specified, as the BRI interrupt is optional.
+	 * interrupt resource is specified as there is only one interrupt ID.
+	 * In the non-muxed case, up to 6 interrupt signals might be generated
+	 * from the SCI, however those signals might have their own individual
+	 * interrupt ID numbers, or muxed together with another interrupt.
 	 */
 	if (sci_port->irqs[0] < 0)
 		return -ENXIO;
 
-	if (sci_port->irqs[1] < 0) {
-		sci_port->irqs[1] = sci_port->irqs[0];
-		sci_port->irqs[2] = sci_port->irqs[0];
-		sci_port->irqs[3] = sci_port->irqs[0];
-	}
+	if (sci_port->irqs[1] < 0)
+		for (i = 1; i < ARRAY_SIZE(sci_port->irqs); i++)
+			sci_port->irqs[i] = sci_port->irqs[0];
 
 	sci_port->params = sci_probe_regmap(p);
 	if (unlikely(sci_port->params == NULL))
-- 
2.16.1

Re: [PATCH v3 1/4] serial: sh-sci: Improve interrupts description

[Rob Herring]

On Tue, Jul 31, 2018 at 05:41:36AM -0500, Chris Brandt wrote:
> Describe interrupts property in more detail, especially when there are
> more than one interrupt.
> 
> Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
> ---
>  .../devicetree/bindings/serial/renesas,sci-serial.txt    | 16 +++++++++++++++-
>  1 file changed, 15 insertions(+), 1 deletion(-)

Reviewed-by: Rob Herring <robh@kernel.org>