* [PATCH 1/2] ath10k: add default value for num_peers in WMI TLV init @ 2018-09-13 14:45 ` Erik Stromdahl 0 siblings, 0 replies; 6+ messages in thread From: Erik Stromdahl @ 2018-09-13 14:45 UTC (permalink / raw) To: kvalo, linux-wireless, ath10k; +Cc: Erik Stromdahl The hw_params value will only be used if it was explicitly set in the global hw_params array. This makes it possible to have the num_peers member unset. Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> --- drivers/net/wireless/ath/ath10k/wmi-tlv.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c index 2640bc389f1d..e8e4ec5443e7 100644 --- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c +++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c @@ -1569,7 +1569,10 @@ static struct sk_buff *ath10k_wmi_tlv_op_gen_init(struct ath10k *ar) cfg->num_vdevs = __cpu_to_le32(TARGET_TLV_NUM_VDEVS); - cfg->num_peers = __cpu_to_le32(ar->hw_params.num_peers); + if (ar->hw_params.num_peers) + cfg->num_peers = __cpu_to_le32(ar->hw_params.num_peers); + else + cfg->num_peers = __cpu_to_le32(TARGET_TLV_NUM_PEERS); cfg->ast_skid_limit = __cpu_to_le32(ar->hw_params.ast_skid_limit); cfg->num_wds_entries = __cpu_to_le32(ar->hw_params.num_wds_entries); -- 2.18.0 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 1/2] ath10k: add default value for num_peers in WMI TLV init @ 2018-09-13 14:45 ` Erik Stromdahl 0 siblings, 0 replies; 6+ messages in thread From: Erik Stromdahl @ 2018-09-13 14:45 UTC (permalink / raw) To: kvalo, linux-wireless, ath10k; +Cc: Erik Stromdahl The hw_params value will only be used if it was explicitly set in the global hw_params array. This makes it possible to have the num_peers member unset. Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> --- drivers/net/wireless/ath/ath10k/wmi-tlv.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c index 2640bc389f1d..e8e4ec5443e7 100644 --- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c +++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c @@ -1569,7 +1569,10 @@ static struct sk_buff *ath10k_wmi_tlv_op_gen_init(struct ath10k *ar) cfg->num_vdevs = __cpu_to_le32(TARGET_TLV_NUM_VDEVS); - cfg->num_peers = __cpu_to_le32(ar->hw_params.num_peers); + if (ar->hw_params.num_peers) + cfg->num_peers = __cpu_to_le32(ar->hw_params.num_peers); + else + cfg->num_peers = __cpu_to_le32(TARGET_TLV_NUM_PEERS); cfg->ast_skid_limit = __cpu_to_le32(ar->hw_params.ast_skid_limit); cfg->num_wds_entries = __cpu_to_le32(ar->hw_params.num_wds_entries); -- 2.18.0 _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] ath10k: remove num_peers in hw_params for most targets 2018-09-13 14:45 ` Erik Stromdahl @ 2018-09-13 14:45 ` Erik Stromdahl -1 siblings, 0 replies; 6+ messages in thread From: Erik Stromdahl @ 2018-09-13 14:45 UTC (permalink / raw) To: kvalo, linux-wireless, ath10k; +Cc: Erik Stromdahl >From commit "ath10k: add per target config of max_num_peers", the num_peers value in struct ath10k_hw_params is used to override the value obtained from the WMI op version in the firmware file. Currently, only high latency devices (USB and SDIO) need to use this value, since the value obtained from the WMI op version is not applicable for these devices. Many devices in ath10k_hw_params_list have the wrong value set. An example of this is the QCA9880 hw2.0 chipset that had (before this patch) num_peers set to TARGET_TLV_NUM_PEERS although the firmware uses WMI version ATH10K_FW_WMI_OP_VERSION_10_2_4. Using the wrong value for the QCA9880 chip results in a fw crash: ath10k_pci 0000:01:00.0: firmware crashed! (guid ddf39880-3e64-4edf-b4e4-979d31724503) ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000 ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 0 ath10k_pci 0000:01:00.0: firmware ver 10.2.4-1.0-00037 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 ath10k_pci 0000:01:00.0: htt-ver 0.0 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 ath10k_pci 0000:01:00.0: firmware register dump: ath10k_pci 0000:01:00.0: [00]: 0x4100016C 0x000015B3 0x009B54B7 0x00955B31 ath10k_pci 0000:01:00.0: [04]: 0x009B54B7 0x00060530 0x00000011 0x00400000 ath10k_pci 0000:01:00.0: [08]: 0x000001B8 0x00000007 0x00443138 0x00955A00 ath10k_pci 0000:01:00.0: [12]: 0x00000009 0x00000000 0x009B548E 0x009B54AB ath10k_pci 0000:01:00.0: [16]: 0x00958080 0x0094078E 0x00000000 0x00000000 ath10k_pci 0000:01:00.0: [20]: 0x409B54B7 0x0040AC64 0x00400000 0x00000087 ath10k_pci 0000:01:00.0: [24]: 0x809A3831 0x0040ACC4 0x000001B1 0xC09B54B7 ath10k_pci 0000:01:00.0: [28]: 0x809A2F08 0x0040AD04 0x00410410 0x00000001 ath10k_pci 0000:01:00.0: [32]: 0x80988856 0x0040AD24 0x00410410 0x00000001 ath10k_pci 0000:01:00.0: [36]: 0x8098AF64 0x0040AD44 0x00410410 0x00000001 ath10k_pci 0000:01:00.0: [40]: 0x809B5DEC 0x0040AD84 0x00410410 0x00410FF4 ath10k_pci 0000:01:00.0: [44]: 0x809B1F20 0x0040ADA4 0x00400000 0x00416C54 ath10k_pci 0000:01:00.0: [48]: 0x809C0295 0x0040ADE4 0x0040AE08 0x00411DC8 ath10k_pci 0000:01:00.0: [52]: 0x809486FA 0x0040AE04 0x00000001 0x00000000 ath10k_pci 0000:01:00.0: [56]: 0x80948E2C 0x0040AEA4 0x0041F290 0x004123D4 ath10k_pci 0000:01:00.0: Copy Engine register dump: ath10k_pci 0000:01:00.0: [00]: 0x00057400 10 10 3 3 ath10k_pci 0000:01:00.0: [01]: 0x00057800 3 3 8 9 ath10k_pci 0000:01:00.0: [02]: 0x00057c00 2 2 1 2 ath10k_pci 0000:01:00.0: [03]: 0x00058000 1 1 2 1 ath10k_pci 0000:01:00.0: [04]: 0x00058400 0 0 40 0 ath10k_pci 0000:01:00.0: [05]: 0x00058800 1 1 0 1 ath10k_pci 0000:01:00.0: [06]: 0x00058c00 0 0 0 0 ath10k_pci 0000:01:00.0: [07]: 0x00059000 0 0 0 0 Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> --- drivers/net/wireless/ath/ath10k/core.c | 13 ------------- 1 file changed, 13 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c index 039ddafdb3b9..11ce6c886d7c 100644 --- a/drivers/net/wireless/ath/ath10k/core.c +++ b/drivers/net/wireless/ath/ath10k/core.c @@ -86,7 +86,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -120,7 +119,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -156,7 +154,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -191,7 +188,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -226,7 +222,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -261,7 +256,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -299,7 +293,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -340,7 +333,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 11, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -388,7 +380,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 1560, .vht160_mcs_tx_highest = 1560, .n_cipher_suites = 11, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -433,7 +424,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 780, .vht160_mcs_tx_highest = 780, .n_cipher_suites = 11, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -468,7 +458,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -505,7 +494,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -599,7 +587,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 11, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, -- 2.18.0 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] ath10k: remove num_peers in hw_params for most targets @ 2018-09-13 14:45 ` Erik Stromdahl 0 siblings, 0 replies; 6+ messages in thread From: Erik Stromdahl @ 2018-09-13 14:45 UTC (permalink / raw) To: kvalo, linux-wireless, ath10k; +Cc: Erik Stromdahl From commit "ath10k: add per target config of max_num_peers", the num_peers value in struct ath10k_hw_params is used to override the value obtained from the WMI op version in the firmware file. Currently, only high latency devices (USB and SDIO) need to use this value, since the value obtained from the WMI op version is not applicable for these devices. Many devices in ath10k_hw_params_list have the wrong value set. An example of this is the QCA9880 hw2.0 chipset that had (before this patch) num_peers set to TARGET_TLV_NUM_PEERS although the firmware uses WMI version ATH10K_FW_WMI_OP_VERSION_10_2_4. Using the wrong value for the QCA9880 chip results in a fw crash: ath10k_pci 0000:01:00.0: firmware crashed! (guid ddf39880-3e64-4edf-b4e4-979d31724503) ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000 ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 0 ath10k_pci 0000:01:00.0: firmware ver 10.2.4-1.0-00037 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 ath10k_pci 0000:01:00.0: htt-ver 0.0 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 ath10k_pci 0000:01:00.0: firmware register dump: ath10k_pci 0000:01:00.0: [00]: 0x4100016C 0x000015B3 0x009B54B7 0x00955B31 ath10k_pci 0000:01:00.0: [04]: 0x009B54B7 0x00060530 0x00000011 0x00400000 ath10k_pci 0000:01:00.0: [08]: 0x000001B8 0x00000007 0x00443138 0x00955A00 ath10k_pci 0000:01:00.0: [12]: 0x00000009 0x00000000 0x009B548E 0x009B54AB ath10k_pci 0000:01:00.0: [16]: 0x00958080 0x0094078E 0x00000000 0x00000000 ath10k_pci 0000:01:00.0: [20]: 0x409B54B7 0x0040AC64 0x00400000 0x00000087 ath10k_pci 0000:01:00.0: [24]: 0x809A3831 0x0040ACC4 0x000001B1 0xC09B54B7 ath10k_pci 0000:01:00.0: [28]: 0x809A2F08 0x0040AD04 0x00410410 0x00000001 ath10k_pci 0000:01:00.0: [32]: 0x80988856 0x0040AD24 0x00410410 0x00000001 ath10k_pci 0000:01:00.0: [36]: 0x8098AF64 0x0040AD44 0x00410410 0x00000001 ath10k_pci 0000:01:00.0: [40]: 0x809B5DEC 0x0040AD84 0x00410410 0x00410FF4 ath10k_pci 0000:01:00.0: [44]: 0x809B1F20 0x0040ADA4 0x00400000 0x00416C54 ath10k_pci 0000:01:00.0: [48]: 0x809C0295 0x0040ADE4 0x0040AE08 0x00411DC8 ath10k_pci 0000:01:00.0: [52]: 0x809486FA 0x0040AE04 0x00000001 0x00000000 ath10k_pci 0000:01:00.0: [56]: 0x80948E2C 0x0040AEA4 0x0041F290 0x004123D4 ath10k_pci 0000:01:00.0: Copy Engine register dump: ath10k_pci 0000:01:00.0: [00]: 0x00057400 10 10 3 3 ath10k_pci 0000:01:00.0: [01]: 0x00057800 3 3 8 9 ath10k_pci 0000:01:00.0: [02]: 0x00057c00 2 2 1 2 ath10k_pci 0000:01:00.0: [03]: 0x00058000 1 1 2 1 ath10k_pci 0000:01:00.0: [04]: 0x00058400 0 0 40 0 ath10k_pci 0000:01:00.0: [05]: 0x00058800 1 1 0 1 ath10k_pci 0000:01:00.0: [06]: 0x00058c00 0 0 0 0 ath10k_pci 0000:01:00.0: [07]: 0x00059000 0 0 0 0 Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> --- drivers/net/wireless/ath/ath10k/core.c | 13 ------------- 1 file changed, 13 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c index 039ddafdb3b9..11ce6c886d7c 100644 --- a/drivers/net/wireless/ath/ath10k/core.c +++ b/drivers/net/wireless/ath/ath10k/core.c @@ -86,7 +86,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -120,7 +119,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -156,7 +154,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -191,7 +188,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -226,7 +222,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -261,7 +256,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -299,7 +293,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -340,7 +333,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 11, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -388,7 +380,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 1560, .vht160_mcs_tx_highest = 1560, .n_cipher_suites = 11, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -433,7 +424,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 780, .vht160_mcs_tx_highest = 780, .n_cipher_suites = 11, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -468,7 +458,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -505,7 +494,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 8, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, @@ -599,7 +587,6 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .vht160_mcs_rx_highest = 0, .vht160_mcs_tx_highest = 0, .n_cipher_suites = 11, - .num_peers = TARGET_TLV_NUM_PEERS, .ast_skid_limit = 0x10, .num_wds_entries = 0x20, .target_64bit = false, -- 2.18.0 _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] ath10k: add default value for num_peers in WMI TLV init 2018-09-13 14:45 ` Erik Stromdahl (?) (?) @ 2018-10-01 13:55 ` Kalle Valo -1 siblings, 0 replies; 6+ messages in thread From: Kalle Valo @ 2018-10-01 13:55 UTC (permalink / raw) To: Erik Stromdahl; +Cc: kvalo, linux-wireless, ath10k Erik Stromdahl <erik.stromdahl@gmail.com> wrote: > The hw_params value will only be used if it was explicitly set in the > global hw_params array. > > This makes it possible to have the num_peers member unset. > > Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> > Signed-off-by: Kalle Valo <kvalo@codeaurora.org> 2 patches applied to ath-next branch of ath.git, thanks. 8e8374db3424 ath10k: add default value for num_peers in WMI TLV init 08fafd646d63 ath10k: remove num_peers in hw_params for most targets -- https://patchwork.kernel.org/patch/10599685/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] ath10k: add default value for num_peers in WMI TLV init 2018-09-13 14:45 ` Erik Stromdahl ` (2 preceding siblings ...) (?) @ 2018-10-01 13:55 ` Kalle Valo -1 siblings, 0 replies; 6+ messages in thread From: Kalle Valo @ 2018-10-01 13:55 UTC (permalink / raw) To: Erik Stromdahl; +Cc: kvalo, linux-wireless, ath10k, Erik Stromdahl Erik Stromdahl <erik.stromdahl@gmail.com> wrote: > The hw_params value will only be used if it was explicitly set in the > global hw_params array. > > This makes it possible to have the num_peers member unset. > > Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> > Signed-off-by: Kalle Valo <kvalo@codeaurora.org> 2 patches applied to ath-next branch of ath.git, thanks. 8e8374db3424 ath10k: add default value for num_peers in WMI TLV init 08fafd646d63 ath10k: remove num_peers in hw_params for most targets -- https://patchwork.kernel.org/patch/10599685/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2018-10-01 13:56 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2018-09-13 14:45 [PATCH 1/2] ath10k: add default value for num_peers in WMI TLV init Erik Stromdahl 2018-09-13 14:45 ` Erik Stromdahl 2018-09-13 14:45 ` [PATCH 2/2] ath10k: remove num_peers in hw_params for most targets Erik Stromdahl 2018-09-13 14:45 ` Erik Stromdahl 2018-10-01 13:55 ` [PATCH 1/2] ath10k: add default value for num_peers in WMI TLV init Kalle Valo 2018-10-01 13:55 ` Kalle Valo
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.