* [PATCH] arm64: dts: add LX2160AQDS board support
@ 2018-09-21 14:17 ` Pankaj Bansal
0 siblings, 0 replies; 18+ messages in thread
From: Pankaj Bansal @ 2018-09-21 14:17 UTC (permalink / raw)
To: linux-arm-kernel, Shawn Guo, Li Yang
Cc: Mark Rutland, devicetree, Yogesh Narayan Gaur, Pankaj Bansal,
Rob Herring, Vabhav Sharma, Sriram Dash
The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
development platform, supporting QorIQ LX2160A processor.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
---
Notes:
This patch is dependent on [1] and [2]
[1] https://lore.kernel.org/patchwork/patch/985935/
[2] https://lore.kernel.org/patchwork/patch/985938/
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/fsl-lx2160a-qds.dts | 88 ++++++++++++++++++
2 files changed, 89 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 445b72bd5a36..ae80fc5c45f7 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -14,3 +14,4 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
new file mode 100644
index 000000000000..5cf2fe279f73
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160AQDS
+//
+// Copyright 2018 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+ model = "NXP Layerscape LX2160AQDS";
+ compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ i2c-mux@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ power-monitor@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+
+ power-monitor@41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ temperature-sensor@4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ };
+
+ temperature-sensor@4d {
+ compatible = "nxp,sa56004";
+ reg = <0x4d>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+ };
+ };
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
--
2.17.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH] arm64: dts: add LX2160AQDS board support
@ 2018-09-21 14:17 ` Pankaj Bansal
0 siblings, 0 replies; 18+ messages in thread
From: Pankaj Bansal @ 2018-09-21 14:17 UTC (permalink / raw)
To: linux-arm-kernel
The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
development platform, supporting QorIQ LX2160A processor.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
---
Notes:
This patch is dependent on [1] and [2]
[1] https://lore.kernel.org/patchwork/patch/985935/
[2] https://lore.kernel.org/patchwork/patch/985938/
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/fsl-lx2160a-qds.dts | 88 ++++++++++++++++++
2 files changed, 89 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 445b72bd5a36..ae80fc5c45f7 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -14,3 +14,4 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
new file mode 100644
index 000000000000..5cf2fe279f73
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160AQDS
+//
+// Copyright 2018 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+ model = "NXP Layerscape LX2160AQDS";
+ compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ i2c-mux at 77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ power-monitor at 40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+
+ power-monitor at 41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ temperature-sensor at 4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ };
+
+ temperature-sensor at 4d {
+ compatible = "nxp,sa56004";
+ reg = <0x4d>;
+ };
+
+ rtc at 51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+ };
+ };
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
--
2.17.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH] arm64: dts: add LX2160AQDS board support
2018-09-21 14:17 ` Pankaj Bansal
@ 2018-09-28 9:00 ` Shawn Guo
-1 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2018-09-28 9:00 UTC (permalink / raw)
To: Pankaj Bansal
Cc: Mark Rutland, devicetree, Yogesh Narayan Gaur, Li Yang,
Rob Herring, Vabhav Sharma, Sriram Dash, linux-arm-kernel
On Fri, Sep 21, 2018 at 07:47:20PM +0530, Pankaj Bansal wrote:
> The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
> development platform, supporting QorIQ LX2160A processor.
>
> Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
> ---
>
> Notes:
> This patch is dependent on [1] and [2]
> [1] https://lore.kernel.org/patchwork/patch/985935/
> [2] https://lore.kernel.org/patchwork/patch/985938/
I did not receive these.
>
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../boot/dts/freescale/fsl-lx2160a-qds.dts | 88 ++++++++++++++++++
> 2 files changed, 89 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 445b72bd5a36..ae80fc5c45f7 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -14,3 +14,4 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
Please keep them in alphabetic order.
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> new file mode 100644
> index 000000000000..5cf2fe279f73
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> @@ -0,0 +1,88 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160AQDS
> +//
> +// Copyright 2018 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a.dtsi"
> +
> +/ {
> + model = "NXP Layerscape LX2160AQDS";
> + compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&i2c0 {
Sort these labeled nodes alphabetically, so that new additions can find
their place easier.
> + status = "okay";
Have a newline between property list and child node.
Shawn
> + i2c-mux@77 {
> + compatible = "nxp,pca9547";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x2>;
> +
> + power-monitor@40 {
> + compatible = "ti,ina220";
> + reg = <0x40>;
> + shunt-resistor = <500>;
> + };
> +
> + power-monitor@41 {
> + compatible = "ti,ina220";
> + reg = <0x41>;
> + shunt-resistor = <1000>;
> + };
> + };
> +
> + i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x3>;
> +
> + temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + };
> +
> + temperature-sensor@4d {
> + compatible = "nxp,sa56004";
> + reg = <0x4d>;
> + };
> +
> + rtc@51 {
> + compatible = "nxp,pcf2129";
> + reg = <0x51>;
> + };
> + };
> + };
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&usb1 {
> + status = "okay";
> +};
> +
> +&crypto {
> + status = "okay";
> +};
> +
> --
> 2.17.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH] arm64: dts: add LX2160AQDS board support
@ 2018-09-28 9:00 ` Shawn Guo
0 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2018-09-28 9:00 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Sep 21, 2018 at 07:47:20PM +0530, Pankaj Bansal wrote:
> The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
> development platform, supporting QorIQ LX2160A processor.
>
> Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
> ---
>
> Notes:
> This patch is dependent on [1] and [2]
> [1] https://lore.kernel.org/patchwork/patch/985935/
> [2] https://lore.kernel.org/patchwork/patch/985938/
I did not receive these.
>
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../boot/dts/freescale/fsl-lx2160a-qds.dts | 88 ++++++++++++++++++
> 2 files changed, 89 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 445b72bd5a36..ae80fc5c45f7 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -14,3 +14,4 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
Please keep them in alphabetic order.
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> new file mode 100644
> index 000000000000..5cf2fe279f73
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> @@ -0,0 +1,88 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160AQDS
> +//
> +// Copyright 2018 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a.dtsi"
> +
> +/ {
> + model = "NXP Layerscape LX2160AQDS";
> + compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&i2c0 {
Sort these labeled nodes alphabetically, so that new additions can find
their place easier.
> + status = "okay";
Have a newline between property list and child node.
Shawn
> + i2c-mux at 77 {
> + compatible = "nxp,pca9547";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c at 2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x2>;
> +
> + power-monitor at 40 {
> + compatible = "ti,ina220";
> + reg = <0x40>;
> + shunt-resistor = <500>;
> + };
> +
> + power-monitor at 41 {
> + compatible = "ti,ina220";
> + reg = <0x41>;
> + shunt-resistor = <1000>;
> + };
> + };
> +
> + i2c at 3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x3>;
> +
> + temperature-sensor at 4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + };
> +
> + temperature-sensor at 4d {
> + compatible = "nxp,sa56004";
> + reg = <0x4d>;
> + };
> +
> + rtc at 51 {
> + compatible = "nxp,pcf2129";
> + reg = <0x51>;
> + };
> + };
> + };
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&usb1 {
> + status = "okay";
> +};
> +
> +&crypto {
> + status = "okay";
> +};
> +
> --
> 2.17.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH] arm64: dts: add LX2160AQDS board support
2018-09-28 9:00 ` Shawn Guo
@ 2018-09-28 19:20 ` Li Yang
-1 siblings, 0 replies; 18+ messages in thread
From: Li Yang @ 2018-09-28 19:20 UTC (permalink / raw)
To: Shawn Guo
Cc: Mark Rutland,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
yogeshnarayan.gaur, pankaj.bansal, Rob Herring, vabhav.sharma,
Sriram Dash,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Fri, Sep 28, 2018 at 4:01 AM Shawn Guo <shawnguo@kernel.org> wrote:
>
> On Fri, Sep 21, 2018 at 07:47:20PM +0530, Pankaj Bansal wrote:
> > The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
> > development platform, supporting QorIQ LX2160A processor.
> >
> > Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> > Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
> > ---
> >
> > Notes:
> > This patch is dependent on [1] and [2]
> > [1] https://lore.kernel.org/patchwork/patch/985935/
> > [2] https://lore.kernel.org/patchwork/patch/985938/
>
> I did not receive these.
Please add the Shawn Guo and me in "to" recipients when you send next
version of these patches. And, btw, I find there is a v3 now, but
your link is still pointing to the v2.
>
> >
> > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > .../boot/dts/freescale/fsl-lx2160a-qds.dts | 88 ++++++++++++++++++
> > 2 files changed, 89 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index 445b72bd5a36..ae80fc5c45f7 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -14,3 +14,4 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
> > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
> > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
> > +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
>
> Please keep them in alphabetic order.
>
> > diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> > new file mode 100644
> > index 000000000000..5cf2fe279f73
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> > @@ -0,0 +1,88 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +//
> > +// Device Tree file for LX2160AQDS
> > +//
> > +// Copyright 2018 NXP
> > +
> > +/dts-v1/;
> > +
> > +#include "fsl-lx2160a.dtsi"
> > +
> > +/ {
> > + model = "NXP Layerscape LX2160AQDS";
> > + compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
>
> Sort these labeled nodes alphabetically, so that new additions can find
> their place easier.
>
> > + status = "okay";
>
> Have a newline between property list and child node.
>
> Shawn
>
> > + i2c-mux@77 {
> > + compatible = "nxp,pca9547";
> > + reg = <0x77>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + i2c@2 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x2>;
> > +
> > + power-monitor@40 {
> > + compatible = "ti,ina220";
> > + reg = <0x40>;
> > + shunt-resistor = <500>;
> > + };
> > +
> > + power-monitor@41 {
> > + compatible = "ti,ina220";
> > + reg = <0x41>;
> > + shunt-resistor = <1000>;
> > + };
> > + };
> > +
> > + i2c@3 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x3>;
> > +
> > + temperature-sensor@4c {
> > + compatible = "nxp,sa56004";
> > + reg = <0x4c>;
> > + };
> > +
> > + temperature-sensor@4d {
> > + compatible = "nxp,sa56004";
> > + reg = <0x4d>;
> > + };
> > +
> > + rtc@51 {
> > + compatible = "nxp,pcf2129";
> > + reg = <0x51>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&usb0 {
> > + status = "okay";
> > +};
> > +
> > +&usb1 {
> > + status = "okay";
> > +};
> > +
> > +&crypto {
> > + status = "okay";
> > +};
> > +
> > --
> > 2.17.1
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH] arm64: dts: add LX2160AQDS board support
@ 2018-09-28 19:20 ` Li Yang
0 siblings, 0 replies; 18+ messages in thread
From: Li Yang @ 2018-09-28 19:20 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Sep 28, 2018 at 4:01 AM Shawn Guo <shawnguo@kernel.org> wrote:
>
> On Fri, Sep 21, 2018 at 07:47:20PM +0530, Pankaj Bansal wrote:
> > The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
> > development platform, supporting QorIQ LX2160A processor.
> >
> > Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> > Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
> > ---
> >
> > Notes:
> > This patch is dependent on [1] and [2]
> > [1] https://lore.kernel.org/patchwork/patch/985935/
> > [2] https://lore.kernel.org/patchwork/patch/985938/
>
> I did not receive these.
Please add the Shawn Guo and me in "to" recipients when you send next
version of these patches. And, btw, I find there is a v3 now, but
your link is still pointing to the v2.
>
> >
> > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > .../boot/dts/freescale/fsl-lx2160a-qds.dts | 88 ++++++++++++++++++
> > 2 files changed, 89 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index 445b72bd5a36..ae80fc5c45f7 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -14,3 +14,4 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
> > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
> > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
> > +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
>
> Please keep them in alphabetic order.
>
> > diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> > new file mode 100644
> > index 000000000000..5cf2fe279f73
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> > @@ -0,0 +1,88 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +//
> > +// Device Tree file for LX2160AQDS
> > +//
> > +// Copyright 2018 NXP
> > +
> > +/dts-v1/;
> > +
> > +#include "fsl-lx2160a.dtsi"
> > +
> > +/ {
> > + model = "NXP Layerscape LX2160AQDS";
> > + compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
>
> Sort these labeled nodes alphabetically, so that new additions can find
> their place easier.
>
> > + status = "okay";
>
> Have a newline between property list and child node.
>
> Shawn
>
> > + i2c-mux at 77 {
> > + compatible = "nxp,pca9547";
> > + reg = <0x77>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + i2c at 2 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x2>;
> > +
> > + power-monitor at 40 {
> > + compatible = "ti,ina220";
> > + reg = <0x40>;
> > + shunt-resistor = <500>;
> > + };
> > +
> > + power-monitor at 41 {
> > + compatible = "ti,ina220";
> > + reg = <0x41>;
> > + shunt-resistor = <1000>;
> > + };
> > + };
> > +
> > + i2c at 3 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x3>;
> > +
> > + temperature-sensor at 4c {
> > + compatible = "nxp,sa56004";
> > + reg = <0x4c>;
> > + };
> > +
> > + temperature-sensor at 4d {
> > + compatible = "nxp,sa56004";
> > + reg = <0x4d>;
> > + };
> > +
> > + rtc at 51 {
> > + compatible = "nxp,pcf2129";
> > + reg = <0x51>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&usb0 {
> > + status = "okay";
> > +};
> > +
> > +&usb1 {
> > + status = "okay";
> > +};
> > +
> > +&crypto {
> > + status = "okay";
> > +};
> > +
> > --
> > 2.17.1
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
* RE: [PATCH] arm64: dts: add LX2160AQDS board support
2018-09-28 19:20 ` Li Yang
@ 2018-09-29 1:54 ` Pankaj Bansal
-1 siblings, 0 replies; 18+ messages in thread
From: Pankaj Bansal @ 2018-09-29 1:54 UTC (permalink / raw)
To: Leo Li, Shawn Guo
Cc: Mark Rutland,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Yogesh Narayan Gaur, Rob Herring, Varun Sethi, Vabhav Sharma,
Sriram Dash,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
Hi Leo,
> -----Original Message-----
> From: Li Yang [mailto:leoyang.li@nxp.com]
> Sent: Saturday, September 29, 2018 12:51 AM
> To: Shawn Guo <shawnguo@kernel.org>
> Cc: Pankaj Bansal <pankaj.bansal@nxp.com>; moderated
> list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE <linux-arm-
> kernel@lists.infradead.org>; Mark Rutland <mark.rutland@arm.com>;
> open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
> <devicetree@vger.kernel.org>; Yogesh Narayan Gaur
> <yogeshnarayan.gaur@nxp.com>; Rob Herring <robh+dt@kernel.org>;
> Vabhav Sharma <vabhav.sharma@nxp.com>; Sriram Dash
> <sriram.dash@nxp.com>
> Subject: Re: [PATCH] arm64: dts: add LX2160AQDS board support
>
> On Fri, Sep 28, 2018 at 4:01 AM Shawn Guo <shawnguo@kernel.org>
> wrote:
> >
> > On Fri, Sep 21, 2018 at 07:47:20PM +0530, Pankaj Bansal wrote:
> > > The LX2160A QorIQ Development System (QDS) is a test, evaluation,
> > > and development platform, supporting QorIQ LX2160A processor.
> > >
> > > Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> > > Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
> > > ---
> > >
> > > Notes:
> > > This patch is dependent on [1] and [2]
> > > [1]
> https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flo
> re.kernel.org%2Fpatchwork%2Fpatch%2F985935%2F&data=02%7C01
> %7Cpankaj.bansal%40nxp.com%7C9463713031ba421c0b7808d625778d4d
> %7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C6367375927397
> 12471&sdata=n8dSYL1yq2zsaVHy4LnnpglK%2Fjn0f4sED0LX3XQma5Y
> %3D&reserved=0
> > > [2]
> > >
> https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fl
> > >
> ore.kernel.org%2Fpatchwork%2Fpatch%2F985938%2F&data=02%7C0
> 1%7Cpa
> > >
> nkaj.bansal%40nxp.com%7C9463713031ba421c0b7808d625778d4d%7C6
> 86ea1d3b
> > >
> c2b4c6fa92cd99c5c301635%7C0%7C0%7C636737592739712471&sd
> ata=SWxih
> > > D1cQTvjnUslr2%2BfBndYvmsCJveIGboc4i5fssU%3D&reserved=0
> >
> > I did not receive these.
>
> Please add the Shawn Guo and me in "to" recipients when you send next
> version of these patches. And, btw, I find there is a v3 now, but your link is
> still pointing to the v2.
Vabhav Sharma sent the patches for LX2160A SOC support. I will ask him to include you and Shawn Guo to add in to list.
I have sent only this patch for LX2160AQDS board, which depends on LX2160A SOC support.
When I sent this patch V2 of SOC patches was the latest version.
I will update the links to V3 SOC support patches, when I send V2 of this patch.
>
> >
> > >
> > > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > > .../boot/dts/freescale/fsl-lx2160a-qds.dts | 88 ++++++++++++++++++
> > > 2 files changed, 89 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/freescale/Makefile
> > > b/arch/arm64/boot/dts/freescale/Makefile
> > > index 445b72bd5a36..ae80fc5c45f7 100644
> > > --- a/arch/arm64/boot/dts/freescale/Makefile
> > > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > > @@ -14,3 +14,4 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) +=
> > > fsl-ls2080a-simu.dtb
> > > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
> > > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> > > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
> > > +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
> >
> > Please keep them in alphabetic order.
Ok.
> >
> > > diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> > > b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> > > new file mode 100644
> > > index 000000000000..5cf2fe279f73
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> > > @@ -0,0 +1,88 @@
> > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) // // Device Tree file
> > > +for LX2160AQDS // // Copyright 2018 NXP
> > > +
> > > +/dts-v1/;
> > > +
> > > +#include "fsl-lx2160a.dtsi"
> > > +
> > > +/ {
> > > + model = "NXP Layerscape LX2160AQDS";
> > > + compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
> > > +
> > > + chosen {
> > > + stdout-path = "serial0:115200n8";
> > > + };
> > > +};
> > > +
> > > +&uart0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&i2c0 {
> >
> > Sort these labeled nodes alphabetically, so that new additions can
> > find their place easier.
Ok.
> >
> > > + status = "okay";
> >
> > Have a newline between property list and child node.
Ok.
> >
> > Shawn
> >
> > > + i2c-mux@77 {
> > > + compatible = "nxp,pca9547";
> > > + reg = <0x77>;
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > +
> > > + i2c@2 {
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > + reg = <0x2>;
> > > +
> > > + power-monitor@40 {
> > > + compatible = "ti,ina220";
> > > + reg = <0x40>;
> > > + shunt-resistor = <500>;
> > > + };
> > > +
> > > + power-monitor@41 {
> > > + compatible = "ti,ina220";
> > > + reg = <0x41>;
> > > + shunt-resistor = <1000>;
> > > + };
> > > + };
> > > +
> > > + i2c@3 {
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > + reg = <0x3>;
> > > +
> > > + temperature-sensor@4c {
> > > + compatible = "nxp,sa56004";
> > > + reg = <0x4c>;
> > > + };
> > > +
> > > + temperature-sensor@4d {
> > > + compatible = "nxp,sa56004";
> > > + reg = <0x4d>;
> > > + };
> > > +
> > > + rtc@51 {
> > > + compatible = "nxp,pcf2129";
> > > + reg = <0x51>;
> > > + };
> > > + };
> > > + };
> > > +};
> > > +
> > > +&usb0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usb1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&crypto {
> > > + status = "okay";
> > > +};
> > > +
> > > --
> > > 2.17.1
> > >
> > >
> > > _______________________________________________
> > > linux-arm-kernel mailing list
> > > linux-arm-kernel@lists.infradead.org
> > >
> https://emea01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fli
> > > sts.infradead.org%2Fmailman%2Flistinfo%2Flinux-arm-
> kernel&data=0
> > >
> 2%7C01%7Cpankaj.bansal%40nxp.com%7C9463713031ba421c0b7808d62
> 5778d4d%
> > >
> 7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C63673759273971
> 2471&
> > >
> sdata=zjGNGbbV8ODaRnL%2F762TTTtRdBC12rbEwD2Gcq3LI0c%3D&r
> eserved=
> > > 0
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH] arm64: dts: add LX2160AQDS board support
@ 2018-09-29 1:54 ` Pankaj Bansal
0 siblings, 0 replies; 18+ messages in thread
From: Pankaj Bansal @ 2018-09-29 1:54 UTC (permalink / raw)
To: linux-arm-kernel
Hi Leo,
> -----Original Message-----
> From: Li Yang [mailto:leoyang.li at nxp.com]
> Sent: Saturday, September 29, 2018 12:51 AM
> To: Shawn Guo <shawnguo@kernel.org>
> Cc: Pankaj Bansal <pankaj.bansal@nxp.com>; moderated
> list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE <linux-arm-
> kernel at lists.infradead.org>; Mark Rutland <mark.rutland@arm.com>;
> open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
> <devicetree@vger.kernel.org>; Yogesh Narayan Gaur
> <yogeshnarayan.gaur@nxp.com>; Rob Herring <robh+dt@kernel.org>;
> Vabhav Sharma <vabhav.sharma@nxp.com>; Sriram Dash
> <sriram.dash@nxp.com>
> Subject: Re: [PATCH] arm64: dts: add LX2160AQDS board support
>
> On Fri, Sep 28, 2018 at 4:01 AM Shawn Guo <shawnguo@kernel.org>
> wrote:
> >
> > On Fri, Sep 21, 2018 at 07:47:20PM +0530, Pankaj Bansal wrote:
> > > The LX2160A QorIQ Development System (QDS) is a test, evaluation,
> > > and development platform, supporting QorIQ LX2160A processor.
> > >
> > > Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> > > Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
> > > ---
> > >
> > > Notes:
> > > This patch is dependent on [1] and [2]
> > > [1]
> https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flo
> re.kernel.org%2Fpatchwork%2Fpatch%2F985935%2F&data=02%7C01
> %7Cpankaj.bansal%40nxp.com%7C9463713031ba421c0b7808d625778d4d
> %7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C6367375927397
> 12471&sdata=n8dSYL1yq2zsaVHy4LnnpglK%2Fjn0f4sED0LX3XQma5Y
> %3D&reserved=0
> > > [2]
> > >
> https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fl
> > >
> ore.kernel.org%2Fpatchwork%2Fpatch%2F985938%2F&data=02%7C0
> 1%7Cpa
> > >
> nkaj.bansal%40nxp.com%7C9463713031ba421c0b7808d625778d4d%7C6
> 86ea1d3b
> > >
> c2b4c6fa92cd99c5c301635%7C0%7C0%7C636737592739712471&sd
> ata=SWxih
> > > D1cQTvjnUslr2%2BfBndYvmsCJveIGboc4i5fssU%3D&reserved=0
> >
> > I did not receive these.
>
> Please add the Shawn Guo and me in "to" recipients when you send next
> version of these patches. And, btw, I find there is a v3 now, but your link is
> still pointing to the v2.
Vabhav Sharma sent the patches for LX2160A SOC support. I will ask him to include you and Shawn Guo to add in to list.
I have sent only this patch for LX2160AQDS board, which depends on LX2160A SOC support.
When I sent this patch V2 of SOC patches was the latest version.
I will update the links to V3 SOC support patches, when I send V2 of this patch.
>
> >
> > >
> > > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > > .../boot/dts/freescale/fsl-lx2160a-qds.dts | 88 ++++++++++++++++++
> > > 2 files changed, 89 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/freescale/Makefile
> > > b/arch/arm64/boot/dts/freescale/Makefile
> > > index 445b72bd5a36..ae80fc5c45f7 100644
> > > --- a/arch/arm64/boot/dts/freescale/Makefile
> > > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > > @@ -14,3 +14,4 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) +=
> > > fsl-ls2080a-simu.dtb
> > > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
> > > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> > > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
> > > +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
> >
> > Please keep them in alphabetic order.
Ok.
> >
> > > diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> > > b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> > > new file mode 100644
> > > index 000000000000..5cf2fe279f73
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> > > @@ -0,0 +1,88 @@
> > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) // // Device Tree file
> > > +for LX2160AQDS // // Copyright 2018 NXP
> > > +
> > > +/dts-v1/;
> > > +
> > > +#include "fsl-lx2160a.dtsi"
> > > +
> > > +/ {
> > > + model = "NXP Layerscape LX2160AQDS";
> > > + compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
> > > +
> > > + chosen {
> > > + stdout-path = "serial0:115200n8";
> > > + };
> > > +};
> > > +
> > > +&uart0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&i2c0 {
> >
> > Sort these labeled nodes alphabetically, so that new additions can
> > find their place easier.
Ok.
> >
> > > + status = "okay";
> >
> > Have a newline between property list and child node.
Ok.
> >
> > Shawn
> >
> > > + i2c-mux at 77 {
> > > + compatible = "nxp,pca9547";
> > > + reg = <0x77>;
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > +
> > > + i2c at 2 {
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > + reg = <0x2>;
> > > +
> > > + power-monitor at 40 {
> > > + compatible = "ti,ina220";
> > > + reg = <0x40>;
> > > + shunt-resistor = <500>;
> > > + };
> > > +
> > > + power-monitor at 41 {
> > > + compatible = "ti,ina220";
> > > + reg = <0x41>;
> > > + shunt-resistor = <1000>;
> > > + };
> > > + };
> > > +
> > > + i2c at 3 {
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > + reg = <0x3>;
> > > +
> > > + temperature-sensor at 4c {
> > > + compatible = "nxp,sa56004";
> > > + reg = <0x4c>;
> > > + };
> > > +
> > > + temperature-sensor at 4d {
> > > + compatible = "nxp,sa56004";
> > > + reg = <0x4d>;
> > > + };
> > > +
> > > + rtc at 51 {
> > > + compatible = "nxp,pcf2129";
> > > + reg = <0x51>;
> > > + };
> > > + };
> > > + };
> > > +};
> > > +
> > > +&usb0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usb1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&crypto {
> > > + status = "okay";
> > > +};
> > > +
> > > --
> > > 2.17.1
> > >
> > >
> > > _______________________________________________
> > > linux-arm-kernel mailing list
> > > linux-arm-kernel at lists.infradead.org
> > >
> https://emea01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fli
> > > sts.infradead.org%2Fmailman%2Flistinfo%2Flinux-arm-
> kernel&data=0
> > >
> 2%7C01%7Cpankaj.bansal%40nxp.com%7C9463713031ba421c0b7808d62
> 5778d4d%
> > >
> 7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C63673759273971
> 2471&
> > >
> sdata=zjGNGbbV8ODaRnL%2F762TTTtRdBC12rbEwD2Gcq3LI0c%3D&r
> eserved=
> > > 0
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v2] arm64: dts: add LX2160AQDS board support
2018-09-21 14:17 ` Pankaj Bansal
@ 2018-10-05 8:10 ` Pankaj Bansal
-1 siblings, 0 replies; 18+ messages in thread
From: Pankaj Bansal @ 2018-10-05 8:10 UTC (permalink / raw)
To: linux-arm-kernel, Shawn Guo, Li Yang
Cc: Mark Rutland, devicetree, Yogesh Narayan Gaur, Pankaj Bansal,
Rob Herring, Vabhav Sharma, Sriram Dash
The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
development platform, supporting QorIQ LX2160A processor.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
---
Notes:
V2:
- Sorted the nodes alphabetically
- Sorted the files' in Makefile alphabetically
- Added newline between property list and sub nodes
- Added and defined vcc-supply property to temperature sensor node in device tree
This patch is dependent on below patches
[1] https://lore.kernel.org/patchwork/patch/995430/
[2] https://lore.kernel.org/patchwork/patch/995433/
[3] https://lore.kernel.org/patchwork/patch/995434/
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/fsl-lx2160a-qds.dts | 100 +++++++++++++++++
2 files changed, 101 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 445b72bd5a36..46b1479b7a6b 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -13,4 +13,5 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
new file mode 100644
index 000000000000..e1df5758c3e4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160AQDS
+//
+// Copyright 2018 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+ model = "NXP Layerscape LX2160AQDS";
+ compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ sb_3v3: regulator-fixed {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ power-monitor@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+
+ power-monitor@41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ temperature-sensor@4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ };
+
+ temperature-sensor@4d {
+ compatible = "nxp,sa56004";
+ reg = <0x4d>;
+ vcc-supply = <&sb_3v3>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
--
2.17.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v2] arm64: dts: add LX2160AQDS board support
@ 2018-10-05 8:10 ` Pankaj Bansal
0 siblings, 0 replies; 18+ messages in thread
From: Pankaj Bansal @ 2018-10-05 8:10 UTC (permalink / raw)
To: linux-arm-kernel
The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
development platform, supporting QorIQ LX2160A processor.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
---
Notes:
V2:
- Sorted the nodes alphabetically
- Sorted the files' in Makefile alphabetically
- Added newline between property list and sub nodes
- Added and defined vcc-supply property to temperature sensor node in device tree
This patch is dependent on below patches
[1] https://lore.kernel.org/patchwork/patch/995430/
[2] https://lore.kernel.org/patchwork/patch/995433/
[3] https://lore.kernel.org/patchwork/patch/995434/
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/fsl-lx2160a-qds.dts | 100 +++++++++++++++++
2 files changed, 101 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 445b72bd5a36..46b1479b7a6b 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -13,4 +13,5 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
new file mode 100644
index 000000000000..e1df5758c3e4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160AQDS
+//
+// Copyright 2018 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+ model = "NXP Layerscape LX2160AQDS";
+ compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ sb_3v3: regulator-fixed {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ i2c-mux at 77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ power-monitor at 40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+
+ power-monitor at 41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ temperature-sensor at 4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ };
+
+ temperature-sensor at 4d {
+ compatible = "nxp,sa56004";
+ reg = <0x4d>;
+ vcc-supply = <&sb_3v3>;
+ };
+
+ rtc at 51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
--
2.17.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v3] arm64: dts: add LX2160AQDS board support
2018-10-05 8:10 ` Pankaj Bansal
@ 2018-10-17 10:32 ` Pankaj Bansal
-1 siblings, 0 replies; 18+ messages in thread
From: Pankaj Bansal @ 2018-10-17 10:32 UTC (permalink / raw)
To: linux-arm-kernel, Shawn Guo, Leo Li
Cc: Mark Rutland, devicetree, Yogesh Narayan Gaur, Pankaj Bansal,
Rob Herring, Vabhav Sharma, Sriram Dash
The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
development platform, supporting QorIQ LX2160A processor.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
---
Notes:
V3:
- Updated temperature sensor regulator name in board device tree
- Added esdhc controller nodes in board device tree
- Added aliases for uart/crypto nodes
V2:
- Sorted the nodes alphabetically
- Sorted the files' in Makefile alphabetically
- Added newline between property list and sub nodes
- Added and defined vcc-supply property to temperature sensor node in device tree
This patch is dependent on below patches
[1] https://lore.kernel.org/patchwork/project/lkml/list/?series=369563
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/fsl-lx2160a-qds.dts | 112 +++++++++++++++++
2 files changed, 113 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 445b72bd5a36..46b1479b7a6b 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -13,4 +13,5 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
new file mode 100644
index 000000000000..99a22abbe725
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160AQDS
+//
+// Copyright 2018 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+ model = "NXP Layerscape LX2160AQDS";
+ compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
+
+ aliases {
+ crypto = &crypto;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ sb_3v3: regulator-sb3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "MC34717-3.3VSB";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+&esdhc0 {
+ status = "okay";
+};
+
+&esdhc1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ power-monitor@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+
+ power-monitor@41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ temperature-sensor@4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ };
+
+ temperature-sensor@4d {
+ compatible = "nxp,sa56004";
+ reg = <0x4d>;
+ vcc-supply = <&sb_3v3>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v3] arm64: dts: add LX2160AQDS board support
@ 2018-10-17 10:32 ` Pankaj Bansal
0 siblings, 0 replies; 18+ messages in thread
From: Pankaj Bansal @ 2018-10-17 10:32 UTC (permalink / raw)
To: linux-arm-kernel
The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
development platform, supporting QorIQ LX2160A processor.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
---
Notes:
V3:
- Updated temperature sensor regulator name in board device tree
- Added esdhc controller nodes in board device tree
- Added aliases for uart/crypto nodes
V2:
- Sorted the nodes alphabetically
- Sorted the files' in Makefile alphabetically
- Added newline between property list and sub nodes
- Added and defined vcc-supply property to temperature sensor node in device tree
This patch is dependent on below patches
[1] https://lore.kernel.org/patchwork/project/lkml/list/?series=369563
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/fsl-lx2160a-qds.dts | 112 +++++++++++++++++
2 files changed, 113 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 445b72bd5a36..46b1479b7a6b 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -13,4 +13,5 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
new file mode 100644
index 000000000000..99a22abbe725
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160AQDS
+//
+// Copyright 2018 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+ model = "NXP Layerscape LX2160AQDS";
+ compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
+
+ aliases {
+ crypto = &crypto;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ sb_3v3: regulator-sb3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "MC34717-3.3VSB";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+&esdhc0 {
+ status = "okay";
+};
+
+&esdhc1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ i2c-mux at 77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ power-monitor at 40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+
+ power-monitor at 41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ temperature-sensor at 4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ };
+
+ temperature-sensor at 4d {
+ compatible = "nxp,sa56004";
+ reg = <0x4d>;
+ vcc-supply = <&sb_3v3>;
+ };
+
+ rtc at 51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v3] arm64: dts: add LX2160AQDS board support
2018-10-17 10:32 ` Pankaj Bansal
@ 2018-10-19 4:16 ` Shawn Guo
-1 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2018-10-19 4:16 UTC (permalink / raw)
To: Pankaj Bansal
Cc: Mark Rutland, devicetree, Yogesh Narayan Gaur, Leo Li,
Rob Herring, Vabhav Sharma, Sriram Dash, linux-arm-kernel
On Wed, Oct 17, 2018 at 10:32:45AM +0000, Pankaj Bansal wrote:
> The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
> development platform, supporting QorIQ LX2160A processor.
>
> Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Looks good to me. @Leo, are you okay with it?
Shawn
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v3] arm64: dts: add LX2160AQDS board support
@ 2018-10-19 4:16 ` Shawn Guo
0 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2018-10-19 4:16 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Oct 17, 2018 at 10:32:45AM +0000, Pankaj Bansal wrote:
> The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
> development platform, supporting QorIQ LX2160A processor.
>
> Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Looks good to me. @Leo, are you okay with it?
Shawn
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v3] arm64: dts: add LX2160AQDS board support
2018-10-19 4:16 ` Shawn Guo
@ 2018-10-22 20:58 ` Li Yang
-1 siblings, 0 replies; 18+ messages in thread
From: Li Yang @ 2018-10-22 20:58 UTC (permalink / raw)
To: Shawn Guo
Cc: Mark Rutland,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
yogeshnarayan.gaur, pankaj.bansal, Rob Herring, Vabhav Sharma,
Sriram Dash,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Thu, Oct 18, 2018 at 11:17 PM Shawn Guo <shawnguo@kernel.org> wrote:
>
> On Wed, Oct 17, 2018 at 10:32:45AM +0000, Pankaj Bansal wrote:
> > The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
> > development platform, supporting QorIQ LX2160A processor.
> >
> > Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> > Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
>
> Looks good to me. @Leo, are you okay with it?
Yes. But be aware that the dependency patches of this patch are not
applied yet.
Acked-by: Li Yang <leoyang.li@nxp.com>
>
> Shawn
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v3] arm64: dts: add LX2160AQDS board support
@ 2018-10-22 20:58 ` Li Yang
0 siblings, 0 replies; 18+ messages in thread
From: Li Yang @ 2018-10-22 20:58 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Oct 18, 2018 at 11:17 PM Shawn Guo <shawnguo@kernel.org> wrote:
>
> On Wed, Oct 17, 2018 at 10:32:45AM +0000, Pankaj Bansal wrote:
> > The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
> > development platform, supporting QorIQ LX2160A processor.
> >
> > Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> > Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
>
> Looks good to me. @Leo, are you okay with it?
Yes. But be aware that the dependency patches of this patch are not
applied yet.
Acked-by: Li Yang <leoyang.li@nxp.com>
>
> Shawn
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v3] arm64: dts: add LX2160AQDS board support
2018-10-17 10:32 ` Pankaj Bansal
@ 2018-10-31 6:27 ` Shawn Guo
-1 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2018-10-31 6:27 UTC (permalink / raw)
To: Pankaj Bansal
Cc: Mark Rutland, devicetree, Yogesh Narayan Gaur, Leo Li,
Rob Herring, Vabhav Sharma, Sriram Dash, linux-arm-kernel
On Wed, Oct 17, 2018 at 10:32:45AM +0000, Pankaj Bansal wrote:
> The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
> development platform, supporting QorIQ LX2160A processor.
>
> Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Applied, thanks.
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v3] arm64: dts: add LX2160AQDS board support
@ 2018-10-31 6:27 ` Shawn Guo
0 siblings, 0 replies; 18+ messages in thread
From: Shawn Guo @ 2018-10-31 6:27 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Oct 17, 2018 at 10:32:45AM +0000, Pankaj Bansal wrote:
> The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
> development platform, supporting QorIQ LX2160A processor.
>
> Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Applied, thanks.
^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2018-10-31 6:27 UTC | newest]
Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-09-21 14:17 [PATCH] arm64: dts: add LX2160AQDS board support Pankaj Bansal
2018-09-21 14:17 ` Pankaj Bansal
2018-09-28 9:00 ` Shawn Guo
2018-09-28 9:00 ` Shawn Guo
2018-09-28 19:20 ` Li Yang
2018-09-28 19:20 ` Li Yang
2018-09-29 1:54 ` Pankaj Bansal
2018-09-29 1:54 ` Pankaj Bansal
2018-10-05 8:10 ` [PATCH v2] " Pankaj Bansal
2018-10-05 8:10 ` Pankaj Bansal
2018-10-17 10:32 ` [PATCH v3] " Pankaj Bansal
2018-10-17 10:32 ` Pankaj Bansal
2018-10-19 4:16 ` Shawn Guo
2018-10-19 4:16 ` Shawn Guo
2018-10-22 20:58 ` Li Yang
2018-10-22 20:58 ` Li Yang
2018-10-31 6:27 ` Shawn Guo
2018-10-31 6:27 ` Shawn Guo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.