* [PATCH v6 0/8] drm/rockchip: migrate to common dw-mipi-dsi bridge and dual-dsi @ 2018-10-01 12:38 ` Heiko Stuebner 0 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: architt, hjc, a.hajda Cc: briannorris, hoegsberg, philippe.cornu, dri-devel, yannick.fertre, linux-rockchip, nickey.yang, mka, seanpaul, linux-arm-kernel The Rockchip DSI driver was separate till now, not using the common bridge driver that was introduced a bit later. So this series migrates over to use that common bridge driver and then also adds support for dual-dsi to both the bridge and Rockchip glue code. The bridge-migration itself is based on Nickeys earlier v8 work, but adapted to current kernels and with a new split between probe and bind, so that we do not create and drop the dsi-host on each deferred bind attempt. changes in v2: - rebase against newer drm code (dsi-bridge+rockchip changes) - add SPDX header to new glue driver - expect regular interface lanes from panel (like 4) not the double number Similar to tegra - keep links to both master and slave changes in v3: - don't defer in bridge_attach, instead add ability to check for finalized panel attachement, for example in bind - address bridge-conversion comments from Andrzej: - include ordering - moved hwaccess from mode_set to enable callback - move pllref_clk enablement to bind (needed by bridge mode_set->lane_mbps) - limited slave settings to dw_mipi_dsi_set_slave - address dual-dsi comments from Philippe: - remove unneeded separate variables - remove unneeded second slave settings - disable slave before master - lane-sum calculation comments changes in v4: - rebase against some legacy rockchip-dsi changes - add dsi-component only after panel has attached to dsi host This solves quite some concurrency problems that happen when trying to determine dsi-panel availability changes in v5: - use driver-internal method to find second host - drop of-graph based dsi method for it changes in v6: - patch7 don't add component on empty local dsi-bus, as some dsi bridges might live on an i2c bus or so and attach from there. Instead check for a slave in dsi-attach and add the slave-component from there if needed - Go back to reading dsi-slave from dt, to prevent possible driver- probe races Heiko Stuebner (4): drm/bridge/synopsys: dsi: move mipi_dsi_host_unregister to __dw_mipi_dsi_remove drm/bridge/synopsys: dsi: don't call __dw_mipi_dsi_probe from dw_mipi_dsi_bind drm/bridge/synopsys: dsi: add ability to have glue-specific attach and detach drm/rockchip: dsi: add dual mipi support Nickey Yang (3): dt-bindings: display: rockchip: update DSI controller drm/rockchip: dsi: migrate to use dw-mipi-dsi bridge driver drm/bridge/synopsys: dsi: add dual-dsi support .../display/rockchip/dw_mipi_dsi_rockchip.txt | 23 +- drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 114 +- drivers/gpu/drm/rockchip/Kconfig | 2 +- drivers/gpu/drm/rockchip/Makefile | 2 +- .../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 1075 +++++++++++++ drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 1349 ----------------- drivers/gpu/drm/rockchip/rockchip_drm_drv.c | 2 +- drivers/gpu/drm/rockchip/rockchip_drm_drv.h | 3 +- drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 3 + drivers/gpu/drm/rockchip/rockchip_drm_vop.h | 4 + drivers/gpu/drm/rockchip/rockchip_vop_reg.c | 1 + include/drm/bridge/dw_mipi_dsi.h | 14 +- 12 files changed, 1213 insertions(+), 1379 deletions(-) create mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c delete mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi.c -- 2.18.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v6 0/8] drm/rockchip: migrate to common dw-mipi-dsi bridge and dual-dsi @ 2018-10-01 12:38 ` Heiko Stuebner 0 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: linux-arm-kernel The Rockchip DSI driver was separate till now, not using the common bridge driver that was introduced a bit later. So this series migrates over to use that common bridge driver and then also adds support for dual-dsi to both the bridge and Rockchip glue code. The bridge-migration itself is based on Nickeys earlier v8 work, but adapted to current kernels and with a new split between probe and bind, so that we do not create and drop the dsi-host on each deferred bind attempt. changes in v2: - rebase against newer drm code (dsi-bridge+rockchip changes) - add SPDX header to new glue driver - expect regular interface lanes from panel (like 4) not the double number Similar to tegra - keep links to both master and slave changes in v3: - don't defer in bridge_attach, instead add ability to check for finalized panel attachement, for example in bind - address bridge-conversion comments from Andrzej: - include ordering - moved hwaccess from mode_set to enable callback - move pllref_clk enablement to bind (needed by bridge mode_set->lane_mbps) - limited slave settings to dw_mipi_dsi_set_slave - address dual-dsi comments from Philippe: - remove unneeded separate variables - remove unneeded second slave settings - disable slave before master - lane-sum calculation comments changes in v4: - rebase against some legacy rockchip-dsi changes - add dsi-component only after panel has attached to dsi host This solves quite some concurrency problems that happen when trying to determine dsi-panel availability changes in v5: - use driver-internal method to find second host - drop of-graph based dsi method for it changes in v6: - patch7 don't add component on empty local dsi-bus, as some dsi bridges might live on an i2c bus or so and attach from there. Instead check for a slave in dsi-attach and add the slave-component from there if needed - Go back to reading dsi-slave from dt, to prevent possible driver- probe races Heiko Stuebner (4): drm/bridge/synopsys: dsi: move mipi_dsi_host_unregister to __dw_mipi_dsi_remove drm/bridge/synopsys: dsi: don't call __dw_mipi_dsi_probe from dw_mipi_dsi_bind drm/bridge/synopsys: dsi: add ability to have glue-specific attach and detach drm/rockchip: dsi: add dual mipi support Nickey Yang (3): dt-bindings: display: rockchip: update DSI controller drm/rockchip: dsi: migrate to use dw-mipi-dsi bridge driver drm/bridge/synopsys: dsi: add dual-dsi support .../display/rockchip/dw_mipi_dsi_rockchip.txt | 23 +- drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 114 +- drivers/gpu/drm/rockchip/Kconfig | 2 +- drivers/gpu/drm/rockchip/Makefile | 2 +- .../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 1075 +++++++++++++ drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 1349 ----------------- drivers/gpu/drm/rockchip/rockchip_drm_drv.c | 2 +- drivers/gpu/drm/rockchip/rockchip_drm_drv.h | 3 +- drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 3 + drivers/gpu/drm/rockchip/rockchip_drm_vop.h | 4 + drivers/gpu/drm/rockchip/rockchip_vop_reg.c | 1 + include/drm/bridge/dw_mipi_dsi.h | 14 +- 12 files changed, 1213 insertions(+), 1379 deletions(-) create mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c delete mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi.c -- 2.18.0 ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v6 1/7] drm/bridge/synopsys: dsi: move mipi_dsi_host_unregister to __dw_mipi_dsi_remove 2018-10-01 12:38 ` Heiko Stuebner @ 2018-10-01 12:38 ` Heiko Stuebner -1 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: architt, hjc, a.hajda Cc: briannorris, hoegsberg, philippe.cornu, dri-devel, yannick.fertre, linux-rockchip, nickey.yang, mka, seanpaul, linux-arm-kernel Right now the host is only unregistered when the driver is used via the bridge api and not via the component api, leading to the host staying registered in cases like probe deferral. So move the host unregister to the general remove function, so that it gets cleaned up in all cases. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> --- drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c index fd7999642cf8..07cde255cab2 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c @@ -941,6 +941,8 @@ __dw_mipi_dsi_probe(struct platform_device *pdev, static void __dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi) { + mipi_dsi_host_unregister(&dsi->dsi_host); + pm_runtime_disable(dsi->dev); } @@ -957,8 +959,6 @@ EXPORT_SYMBOL_GPL(dw_mipi_dsi_probe); void dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi) { - mipi_dsi_host_unregister(&dsi->dsi_host); - __dw_mipi_dsi_remove(dsi); } EXPORT_SYMBOL_GPL(dw_mipi_dsi_remove); -- 2.18.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 1/7] drm/bridge/synopsys: dsi: move mipi_dsi_host_unregister to __dw_mipi_dsi_remove @ 2018-10-01 12:38 ` Heiko Stuebner 0 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: linux-arm-kernel Right now the host is only unregistered when the driver is used via the bridge api and not via the component api, leading to the host staying registered in cases like probe deferral. So move the host unregister to the general remove function, so that it gets cleaned up in all cases. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> --- drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c index fd7999642cf8..07cde255cab2 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c @@ -941,6 +941,8 @@ __dw_mipi_dsi_probe(struct platform_device *pdev, static void __dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi) { + mipi_dsi_host_unregister(&dsi->dsi_host); + pm_runtime_disable(dsi->dev); } @@ -957,8 +959,6 @@ EXPORT_SYMBOL_GPL(dw_mipi_dsi_probe); void dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi) { - mipi_dsi_host_unregister(&dsi->dsi_host); - __dw_mipi_dsi_remove(dsi); } EXPORT_SYMBOL_GPL(dw_mipi_dsi_remove); -- 2.18.0 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 2/7] drm/bridge/synopsys: dsi: don't call __dw_mipi_dsi_probe from dw_mipi_dsi_bind 2018-10-01 12:38 ` Heiko Stuebner @ 2018-10-01 12:38 ` Heiko Stuebner -1 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: architt, hjc, a.hajda Cc: briannorris, hoegsberg, philippe.cornu, dri-devel, yannick.fertre, linux-rockchip, nickey.yang, mka, seanpaul, linux-arm-kernel __dw_mipi_dsi_probe() does all the grabbing of resources and does it using devm-helpers. So this is happening on each try of master bringup possibly slowing down things a lot. Drivers using the component framework may instead want to call dw_mipi_dsi_probe separately in their probe function to setup resources early. That way the dsi bus also gets created earlier and also not recreated on each bind-try, so that attached panels can load their modules and be probed way before the bridge-attach in the bind call. So drop the call to __dw_mipi_dsi_probe and modify the function to take a struct dw_mipi_dsi instead of the platform-device. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> --- drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 15 +++------------ include/drm/bridge/dw_mipi_dsi.h | 5 +---- 2 files changed, 4 insertions(+), 16 deletions(-) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c index 07cde255cab2..bb4aeca5c0f9 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c @@ -966,31 +966,22 @@ EXPORT_SYMBOL_GPL(dw_mipi_dsi_remove); /* * Bind/unbind API, used from platforms based on the component framework. */ -struct dw_mipi_dsi * -dw_mipi_dsi_bind(struct platform_device *pdev, struct drm_encoder *encoder, - const struct dw_mipi_dsi_plat_data *plat_data) +int dw_mipi_dsi_bind(struct dw_mipi_dsi *dsi, struct drm_encoder *encoder) { - struct dw_mipi_dsi *dsi; int ret; - dsi = __dw_mipi_dsi_probe(pdev, plat_data); - if (IS_ERR(dsi)) - return dsi; - ret = drm_bridge_attach(encoder, &dsi->bridge, NULL); if (ret) { - dw_mipi_dsi_remove(dsi); DRM_ERROR("Failed to initialize bridge with drm\n"); - return ERR_PTR(ret); + return ret; } - return dsi; + return ret; } EXPORT_SYMBOL_GPL(dw_mipi_dsi_bind); void dw_mipi_dsi_unbind(struct dw_mipi_dsi *dsi) { - __dw_mipi_dsi_remove(dsi); } EXPORT_SYMBOL_GPL(dw_mipi_dsi_unbind); diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h index d9c6d549f971..6d7f8eb5d9f2 100644 --- a/include/drm/bridge/dw_mipi_dsi.h +++ b/include/drm/bridge/dw_mipi_dsi.h @@ -35,10 +35,7 @@ struct dw_mipi_dsi *dw_mipi_dsi_probe(struct platform_device *pdev, const struct dw_mipi_dsi_plat_data *plat_data); void dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi); -struct dw_mipi_dsi *dw_mipi_dsi_bind(struct platform_device *pdev, - struct drm_encoder *encoder, - const struct dw_mipi_dsi_plat_data - *plat_data); +int dw_mipi_dsi_bind(struct dw_mipi_dsi *dsi, struct drm_encoder *encoder); void dw_mipi_dsi_unbind(struct dw_mipi_dsi *dsi); #endif /* __DW_MIPI_DSI__ */ -- 2.18.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 2/7] drm/bridge/synopsys: dsi: don't call __dw_mipi_dsi_probe from dw_mipi_dsi_bind @ 2018-10-01 12:38 ` Heiko Stuebner 0 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: linux-arm-kernel __dw_mipi_dsi_probe() does all the grabbing of resources and does it using devm-helpers. So this is happening on each try of master bringup possibly slowing down things a lot. Drivers using the component framework may instead want to call dw_mipi_dsi_probe separately in their probe function to setup resources early. That way the dsi bus also gets created earlier and also not recreated on each bind-try, so that attached panels can load their modules and be probed way before the bridge-attach in the bind call. So drop the call to __dw_mipi_dsi_probe and modify the function to take a struct dw_mipi_dsi instead of the platform-device. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> --- drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 15 +++------------ include/drm/bridge/dw_mipi_dsi.h | 5 +---- 2 files changed, 4 insertions(+), 16 deletions(-) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c index 07cde255cab2..bb4aeca5c0f9 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c @@ -966,31 +966,22 @@ EXPORT_SYMBOL_GPL(dw_mipi_dsi_remove); /* * Bind/unbind API, used from platforms based on the component framework. */ -struct dw_mipi_dsi * -dw_mipi_dsi_bind(struct platform_device *pdev, struct drm_encoder *encoder, - const struct dw_mipi_dsi_plat_data *plat_data) +int dw_mipi_dsi_bind(struct dw_mipi_dsi *dsi, struct drm_encoder *encoder) { - struct dw_mipi_dsi *dsi; int ret; - dsi = __dw_mipi_dsi_probe(pdev, plat_data); - if (IS_ERR(dsi)) - return dsi; - ret = drm_bridge_attach(encoder, &dsi->bridge, NULL); if (ret) { - dw_mipi_dsi_remove(dsi); DRM_ERROR("Failed to initialize bridge with drm\n"); - return ERR_PTR(ret); + return ret; } - return dsi; + return ret; } EXPORT_SYMBOL_GPL(dw_mipi_dsi_bind); void dw_mipi_dsi_unbind(struct dw_mipi_dsi *dsi) { - __dw_mipi_dsi_remove(dsi); } EXPORT_SYMBOL_GPL(dw_mipi_dsi_unbind); diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h index d9c6d549f971..6d7f8eb5d9f2 100644 --- a/include/drm/bridge/dw_mipi_dsi.h +++ b/include/drm/bridge/dw_mipi_dsi.h @@ -35,10 +35,7 @@ struct dw_mipi_dsi *dw_mipi_dsi_probe(struct platform_device *pdev, const struct dw_mipi_dsi_plat_data *plat_data); void dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi); -struct dw_mipi_dsi *dw_mipi_dsi_bind(struct platform_device *pdev, - struct drm_encoder *encoder, - const struct dw_mipi_dsi_plat_data - *plat_data); +int dw_mipi_dsi_bind(struct dw_mipi_dsi *dsi, struct drm_encoder *encoder); void dw_mipi_dsi_unbind(struct dw_mipi_dsi *dsi); #endif /* __DW_MIPI_DSI__ */ -- 2.18.0 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 3/7] drm/bridge/synopsys: dsi: add ability to have glue-specific attach and detach 2018-10-01 12:38 ` Heiko Stuebner @ 2018-10-01 12:38 ` Heiko Stuebner -1 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: architt, hjc, a.hajda Cc: briannorris, hoegsberg, philippe.cornu, dri-devel, yannick.fertre, linux-rockchip, nickey.yang, mka, seanpaul, linux-arm-kernel With the regular means of adding the dsi-component in probe it creates a race condition with the panel probing, as the panel device only gets created after the dsi-bus got created. When the panel-driver is build as a module it currently fails hard as the panel cannot be probed directly: dw_mipi_dsi_bind() __dw_mipi_dsi_probe() creates dsi bus creates panel device triggers panel module load panel not probed (module not loaded or panel probe slow) drm_bridge_attach fails with -EINVAL due to empty panel_bridge Additionally the panel probing can run concurrently with dsi bringup making it possible that the panel can already be found but dsi-attach hasn't finished running. To solve that cleanly we may want to only create the component after the panel has finished probing, by calling component_add from the host-attach dsi callback. As that is specific to glue drivers, add a new struct for host_ops so that glue drivers can tell the bridge to call specific functions after the common host-attach and before the common host-detach run. Suggested-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 15 +++++++++++++++ include/drm/bridge/dw_mipi_dsi.h | 8 ++++++++ 2 files changed, 23 insertions(+) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c index bb4aeca5c0f9..3962e5d84e1e 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c @@ -270,6 +270,7 @@ static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host, struct mipi_dsi_device *device) { struct dw_mipi_dsi *dsi = host_to_dsi(host); + const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data; struct drm_bridge *bridge; struct drm_panel *panel; int ret; @@ -300,6 +301,12 @@ static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host, drm_bridge_add(&dsi->bridge); + if (pdata->host_ops && pdata->host_ops->attach) { + ret = pdata->host_ops->attach(pdata->priv_data, device); + if (ret < 0) + return ret; + } + return 0; } @@ -307,6 +314,14 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host, struct mipi_dsi_device *device) { struct dw_mipi_dsi *dsi = host_to_dsi(host); + const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data; + int ret; + + if (pdata->host_ops && pdata->host_ops->detach) { + ret = pdata->host_ops->detach(pdata->priv_data, device); + if (ret < 0) + return ret; + } drm_of_panel_bridge_remove(host->dev->of_node, 1, 0); diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h index 6d7f8eb5d9f2..a9c03099cf3e 100644 --- a/include/drm/bridge/dw_mipi_dsi.h +++ b/include/drm/bridge/dw_mipi_dsi.h @@ -19,6 +19,13 @@ struct dw_mipi_dsi_phy_ops { unsigned int *lane_mbps); }; +struct dw_mipi_dsi_host_ops { + int (*attach)(void *priv_data, + struct mipi_dsi_device *dsi); + int (*detach)(void *priv_data, + struct mipi_dsi_device *dsi); +}; + struct dw_mipi_dsi_plat_data { void __iomem *base; unsigned int max_data_lanes; @@ -27,6 +34,7 @@ struct dw_mipi_dsi_plat_data { const struct drm_display_mode *mode); const struct dw_mipi_dsi_phy_ops *phy_ops; + const struct dw_mipi_dsi_host_ops *host_ops; void *priv_data; }; -- 2.18.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 3/7] drm/bridge/synopsys: dsi: add ability to have glue-specific attach and detach @ 2018-10-01 12:38 ` Heiko Stuebner 0 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: linux-arm-kernel With the regular means of adding the dsi-component in probe it creates a race condition with the panel probing, as the panel device only gets created after the dsi-bus got created. When the panel-driver is build as a module it currently fails hard as the panel cannot be probed directly: dw_mipi_dsi_bind() __dw_mipi_dsi_probe() creates dsi bus creates panel device triggers panel module load panel not probed (module not loaded or panel probe slow) drm_bridge_attach fails with -EINVAL due to empty panel_bridge Additionally the panel probing can run concurrently with dsi bringup making it possible that the panel can already be found but dsi-attach hasn't finished running. To solve that cleanly we may want to only create the component after the panel has finished probing, by calling component_add from the host-attach dsi callback. As that is specific to glue drivers, add a new struct for host_ops so that glue drivers can tell the bridge to call specific functions after the common host-attach and before the common host-detach run. Suggested-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 15 +++++++++++++++ include/drm/bridge/dw_mipi_dsi.h | 8 ++++++++ 2 files changed, 23 insertions(+) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c index bb4aeca5c0f9..3962e5d84e1e 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c @@ -270,6 +270,7 @@ static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host, struct mipi_dsi_device *device) { struct dw_mipi_dsi *dsi = host_to_dsi(host); + const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data; struct drm_bridge *bridge; struct drm_panel *panel; int ret; @@ -300,6 +301,12 @@ static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host, drm_bridge_add(&dsi->bridge); + if (pdata->host_ops && pdata->host_ops->attach) { + ret = pdata->host_ops->attach(pdata->priv_data, device); + if (ret < 0) + return ret; + } + return 0; } @@ -307,6 +314,14 @@ static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host, struct mipi_dsi_device *device) { struct dw_mipi_dsi *dsi = host_to_dsi(host); + const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data; + int ret; + + if (pdata->host_ops && pdata->host_ops->detach) { + ret = pdata->host_ops->detach(pdata->priv_data, device); + if (ret < 0) + return ret; + } drm_of_panel_bridge_remove(host->dev->of_node, 1, 0); diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h index 6d7f8eb5d9f2..a9c03099cf3e 100644 --- a/include/drm/bridge/dw_mipi_dsi.h +++ b/include/drm/bridge/dw_mipi_dsi.h @@ -19,6 +19,13 @@ struct dw_mipi_dsi_phy_ops { unsigned int *lane_mbps); }; +struct dw_mipi_dsi_host_ops { + int (*attach)(void *priv_data, + struct mipi_dsi_device *dsi); + int (*detach)(void *priv_data, + struct mipi_dsi_device *dsi); +}; + struct dw_mipi_dsi_plat_data { void __iomem *base; unsigned int max_data_lanes; @@ -27,6 +34,7 @@ struct dw_mipi_dsi_plat_data { const struct drm_display_mode *mode); const struct dw_mipi_dsi_phy_ops *phy_ops; + const struct dw_mipi_dsi_host_ops *host_ops; void *priv_data; }; -- 2.18.0 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 4/7] dt-bindings: display: rockchip: update DSI controller 2018-10-01 12:38 ` Heiko Stuebner @ 2018-10-01 12:38 ` Heiko Stuebner -1 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: architt, hjc, a.hajda Cc: briannorris, hoegsberg, philippe.cornu, dri-devel, yannick.fertre, linux-rockchip, nickey.yang, mka, seanpaul, linux-arm-kernel From: Nickey Yang <nickey.yang@rock-chips.com> This patch update describe panel/port links, including unit addresses in documentation of device tree bindings for the rockchip DSI controller based on the Synopsys DesignWare MIPI DSI host controller. Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- .../display/rockchip/dw_mipi_dsi_rockchip.txt | 23 +++++++++++++++++-- 1 file changed, 21 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt index 6bb59ab39f2f..ce4c1fc9116c 100644 --- a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt +++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt @@ -14,6 +14,8 @@ Required properties: - rockchip,grf: this soc should set GRF regs to mux vopl/vopb. - ports: contain a port node with endpoint definitions as defined in [2]. For vopb,set the reg = <0> and set the reg = <1> for vopl. +- video port 0 for the VOP input, the remote endpoint maybe vopb or vopl +- video port 1 for either a panel or subsequent encoder Optional properties: - power-domains: a phandle to mipi dsi power domain node. @@ -40,11 +42,12 @@ Example: ports { #address-cells = <1>; #size-cells = <0>; - reg = <1>; - mipi_in: port { + mipi_in: port@0 { + reg = <0>; #address-cells = <1>; #size-cells = <0>; + mipi_in_vopb: endpoint@0 { reg = <0>; remote-endpoint = <&vopb_out_mipi>; @@ -54,6 +57,16 @@ Example: remote-endpoint = <&vopl_out_mipi>; }; }; + + mipi_out: port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + mipi_out_panel: endpoint { + remote-endpoint = <&panel_in_mipi>; + }; + }; }; panel { @@ -64,5 +77,11 @@ Example: pinctrl-names = "default"; pinctrl-0 = <&lcd_en>; backlight = <&backlight>; + + port { + panel_in_mipi: endpoint { + remote-endpoint = <&mipi_out_panel>; + }; + }; }; }; -- 2.18.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 4/7] dt-bindings: display: rockchip: update DSI controller @ 2018-10-01 12:38 ` Heiko Stuebner 0 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: linux-arm-kernel From: Nickey Yang <nickey.yang@rock-chips.com> This patch update describe panel/port links, including unit addresses in documentation of device tree bindings for the rockchip DSI controller based on the Synopsys DesignWare MIPI DSI host controller. Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- .../display/rockchip/dw_mipi_dsi_rockchip.txt | 23 +++++++++++++++++-- 1 file changed, 21 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt index 6bb59ab39f2f..ce4c1fc9116c 100644 --- a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt +++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt @@ -14,6 +14,8 @@ Required properties: - rockchip,grf: this soc should set GRF regs to mux vopl/vopb. - ports: contain a port node with endpoint definitions as defined in [2]. For vopb,set the reg = <0> and set the reg = <1> for vopl. +- video port 0 for the VOP input, the remote endpoint maybe vopb or vopl +- video port 1 for either a panel or subsequent encoder Optional properties: - power-domains: a phandle to mipi dsi power domain node. @@ -40,11 +42,12 @@ Example: ports { #address-cells = <1>; #size-cells = <0>; - reg = <1>; - mipi_in: port { + mipi_in: port at 0 { + reg = <0>; #address-cells = <1>; #size-cells = <0>; + mipi_in_vopb: endpoint at 0 { reg = <0>; remote-endpoint = <&vopb_out_mipi>; @@ -54,6 +57,16 @@ Example: remote-endpoint = <&vopl_out_mipi>; }; }; + + mipi_out: port at 1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + mipi_out_panel: endpoint { + remote-endpoint = <&panel_in_mipi>; + }; + }; }; panel { @@ -64,5 +77,11 @@ Example: pinctrl-names = "default"; pinctrl-0 = <&lcd_en>; backlight = <&backlight>; + + port { + panel_in_mipi: endpoint { + remote-endpoint = <&mipi_out_panel>; + }; + }; }; }; -- 2.18.0 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 5/7] drm/rockchip: dsi: migrate to use dw-mipi-dsi bridge driver 2018-10-01 12:38 ` Heiko Stuebner @ 2018-10-01 12:38 ` Heiko Stuebner -1 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: architt, hjc, a.hajda Cc: briannorris, hoegsberg, philippe.cornu, dri-devel, yannick.fertre, linux-rockchip, nickey.yang, mka, seanpaul, linux-arm-kernel From: Nickey Yang <nickey.yang@rock-chips.com> Add the ROCKCHIP DSI controller driver that uses the Synopsys DesignWare MIPI DSI host controller bridge and remove the old separate one. changes: v2: add err_pllref, remove unnecessary encoder.enable & disable correct spelling mistakes v3: call dw_mipi_dsi_unbind() in dw_mipi_dsi_rockchip_unbind() fix typo, use of_device_get_match_data(), change some bind() logic into probe() add 'dev_set_drvdata()' v4: return -EINVAL when can not get best_freq add a clarifying comment when get vco add review tag v5: keep our power domain enabled while touching GRF v6: change func name dw_mipi_encoder_disable to dw_mipi_dsi_encoder_disable v7: none v8: Heiko add Archit's Review tag adapt to recent changes in the original rockchip-dsi driver beautify grf-handling split hw-setup (resources, dsi-host) from bind into probe v2-new: Heiko add SPDX header instead of license blurb drop old versioning to not confuse people v3-new: Heiko include ordering moved hwaccess from mode_set to enable callback move pllref_clk enablement to bind (needed by bridge mode_set->lane_mbps) v4-new: Heiko rebase against recent rockchip-dsi changes move to call component_add in the new glue host-attach Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Archit Taneja <architt@codeaurora.org> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- drivers/gpu/drm/rockchip/Kconfig | 2 +- drivers/gpu/drm/rockchip/Makefile | 2 +- .../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 939 ++++++++++++ drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 1349 ----------------- drivers/gpu/drm/rockchip/rockchip_drm_drv.c | 2 +- drivers/gpu/drm/rockchip/rockchip_drm_drv.h | 2 +- 6 files changed, 943 insertions(+), 1353 deletions(-) create mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c delete mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi.c diff --git a/drivers/gpu/drm/rockchip/Kconfig b/drivers/gpu/drm/rockchip/Kconfig index 26438d45732b..1e75196f9659 100644 --- a/drivers/gpu/drm/rockchip/Kconfig +++ b/drivers/gpu/drm/rockchip/Kconfig @@ -7,7 +7,7 @@ config DRM_ROCKCHIP select VIDEOMODE_HELPERS select DRM_ANALOGIX_DP if ROCKCHIP_ANALOGIX_DP select DRM_DW_HDMI if ROCKCHIP_DW_HDMI - select DRM_MIPI_DSI if ROCKCHIP_DW_MIPI_DSI + select DRM_DW_MIPI_DSI if ROCKCHIP_DW_MIPI_DSI select DRM_RGB if ROCKCHIP_RGB select SND_SOC_HDMI_CODEC if ROCKCHIP_CDN_DP && SND_SOC help diff --git a/drivers/gpu/drm/rockchip/Makefile b/drivers/gpu/drm/rockchip/Makefile index 868263ff0302..f6fc9d5dd0ad 100644 --- a/drivers/gpu/drm/rockchip/Makefile +++ b/drivers/gpu/drm/rockchip/Makefile @@ -11,7 +11,7 @@ rockchipdrm-$(CONFIG_DRM_FBDEV_EMULATION) += rockchip_drm_fbdev.o rockchipdrm-$(CONFIG_ROCKCHIP_ANALOGIX_DP) += analogix_dp-rockchip.o rockchipdrm-$(CONFIG_ROCKCHIP_CDN_DP) += cdn-dp-core.o cdn-dp-reg.o rockchipdrm-$(CONFIG_ROCKCHIP_DW_HDMI) += dw_hdmi-rockchip.o -rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi.o +rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi-rockchip.o rockchipdrm-$(CONFIG_ROCKCHIP_INNO_HDMI) += inno_hdmi.o rockchipdrm-$(CONFIG_ROCKCHIP_LVDS) += rockchip_lvds.o rockchipdrm-$(CONFIG_ROCKCHIP_RGB) += rockchip_rgb.o diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c new file mode 100644 index 000000000000..b3aae8439aa3 --- /dev/null +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c @@ -0,0 +1,939 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd + * Author: + * Chris Zhong <zyw@rock-chips.com> + * Nickey Yang <nickey.yang@rock-chips.com> + */ + +#include <drm/drmP.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/bridge/dw_mipi_dsi.h> +#include <drm/drm_of.h> +#include <linux/clk.h> +#include <linux/iopoll.h> +#include <linux/math64.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/pm_runtime.h> +#include <linux/regmap.h> +#include <video/mipi_display.h> + +#include "rockchip_drm_drv.h" +#include "rockchip_drm_vop.h" + +#define DSI_PHY_RSTZ 0xa0 +#define PHY_DISFORCEPLL 0 +#define PHY_ENFORCEPLL BIT(3) +#define PHY_DISABLECLK 0 +#define PHY_ENABLECLK BIT(2) +#define PHY_RSTZ 0 +#define PHY_UNRSTZ BIT(1) +#define PHY_SHUTDOWNZ 0 +#define PHY_UNSHUTDOWNZ BIT(0) + +#define DSI_PHY_IF_CFG 0xa4 +#define N_LANES(n) ((((n) - 1) & 0x3) << 0) +#define PHY_STOP_WAIT_TIME(cycle) (((cycle) & 0xff) << 8) + +#define DSI_PHY_STATUS 0xb0 +#define LOCK BIT(0) +#define STOP_STATE_CLK_LANE BIT(2) + +#define DSI_PHY_TST_CTRL0 0xb4 +#define PHY_TESTCLK BIT(1) +#define PHY_UNTESTCLK 0 +#define PHY_TESTCLR BIT(0) +#define PHY_UNTESTCLR 0 + +#define DSI_PHY_TST_CTRL1 0xb8 +#define PHY_TESTEN BIT(16) +#define PHY_UNTESTEN 0 +#define PHY_TESTDOUT(n) (((n) & 0xff) << 8) +#define PHY_TESTDIN(n) (((n) & 0xff) << 0) + +#define DSI_INT_ST0 0xbc +#define DSI_INT_ST1 0xc0 +#define DSI_INT_MSK0 0xc4 +#define DSI_INT_MSK1 0xc8 + +#define PHY_STATUS_TIMEOUT_US 10000 +#define CMD_PKT_STATUS_TIMEOUT_US 20000 + +#define BYPASS_VCO_RANGE BIT(7) +#define VCO_RANGE_CON_SEL(val) (((val) & 0x7) << 3) +#define VCO_IN_CAP_CON_DEFAULT (0x0 << 1) +#define VCO_IN_CAP_CON_LOW (0x1 << 1) +#define VCO_IN_CAP_CON_HIGH (0x2 << 1) +#define REF_BIAS_CUR_SEL BIT(0) + +#define CP_CURRENT_3UA 0x1 +#define CP_CURRENT_4_5UA 0x2 +#define CP_CURRENT_7_5UA 0x6 +#define CP_CURRENT_6UA 0x9 +#define CP_CURRENT_12UA 0xb +#define CP_CURRENT_SEL(val) ((val) & 0xf) +#define CP_PROGRAM_EN BIT(7) + +#define LPF_RESISTORS_15_5KOHM 0x1 +#define LPF_RESISTORS_13KOHM 0x2 +#define LPF_RESISTORS_11_5KOHM 0x4 +#define LPF_RESISTORS_10_5KOHM 0x8 +#define LPF_RESISTORS_8KOHM 0x10 +#define LPF_PROGRAM_EN BIT(6) +#define LPF_RESISTORS_SEL(val) ((val) & 0x3f) + +#define HSFREQRANGE_SEL(val) (((val) & 0x3f) << 1) + +#define INPUT_DIVIDER(val) (((val) - 1) & 0x7f) +#define LOW_PROGRAM_EN 0 +#define HIGH_PROGRAM_EN BIT(7) +#define LOOP_DIV_LOW_SEL(val) (((val) - 1) & 0x1f) +#define LOOP_DIV_HIGH_SEL(val) ((((val) - 1) >> 5) & 0xf) +#define PLL_LOOP_DIV_EN BIT(5) +#define PLL_INPUT_DIV_EN BIT(4) + +#define POWER_CONTROL BIT(6) +#define INTERNAL_REG_CURRENT BIT(3) +#define BIAS_BLOCK_ON BIT(2) +#define BANDGAP_ON BIT(0) + +#define TER_RESISTOR_HIGH BIT(7) +#define TER_RESISTOR_LOW 0 +#define LEVEL_SHIFTERS_ON BIT(6) +#define TER_CAL_DONE BIT(5) +#define SETRD_MAX (0x7 << 2) +#define POWER_MANAGE BIT(1) +#define TER_RESISTORS_ON BIT(0) + +#define BIASEXTR_SEL(val) ((val) & 0x7) +#define BANDGAP_SEL(val) ((val) & 0x7) +#define TLP_PROGRAM_EN BIT(7) +#define THS_PRE_PROGRAM_EN BIT(7) +#define THS_ZERO_PROGRAM_EN BIT(6) + +#define PLL_BIAS_CUR_SEL_CAP_VCO_CONTROL 0x10 +#define PLL_CP_CONTROL_PLL_LOCK_BYPASS 0x11 +#define PLL_LPF_AND_CP_CONTROL 0x12 +#define PLL_INPUT_DIVIDER_RATIO 0x17 +#define PLL_LOOP_DIVIDER_RATIO 0x18 +#define PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL 0x19 +#define BANDGAP_AND_BIAS_CONTROL 0x20 +#define TERMINATION_RESISTER_CONTROL 0x21 +#define AFE_BIAS_BANDGAP_ANALOG_PROGRAMMABILITY 0x22 +#define HS_RX_CONTROL_OF_LANE_0 0x44 +#define HS_TX_CLOCK_LANE_REQUEST_STATE_TIME_CONTROL 0x60 +#define HS_TX_CLOCK_LANE_PREPARE_STATE_TIME_CONTROL 0x61 +#define HS_TX_CLOCK_LANE_HS_ZERO_STATE_TIME_CONTROL 0x62 +#define HS_TX_CLOCK_LANE_TRAIL_STATE_TIME_CONTROL 0x63 +#define HS_TX_CLOCK_LANE_EXIT_STATE_TIME_CONTROL 0x64 +#define HS_TX_CLOCK_LANE_POST_TIME_CONTROL 0x65 +#define HS_TX_DATA_LANE_REQUEST_STATE_TIME_CONTROL 0x70 +#define HS_TX_DATA_LANE_PREPARE_STATE_TIME_CONTROL 0x71 +#define HS_TX_DATA_LANE_HS_ZERO_STATE_TIME_CONTROL 0x72 +#define HS_TX_DATA_LANE_TRAIL_STATE_TIME_CONTROL 0x73 +#define HS_TX_DATA_LANE_EXIT_STATE_TIME_CONTROL 0x74 + +#define DW_MIPI_NEEDS_PHY_CFG_CLK BIT(0) +#define DW_MIPI_NEEDS_GRF_CLK BIT(1) + +#define RK3288_GRF_SOC_CON6 0x025c +#define RK3288_DSI0_LCDC_SEL BIT(6) +#define RK3288_DSI1_LCDC_SEL BIT(9) + +#define RK3399_GRF_SOC_CON20 0x6250 +#define RK3399_DSI0_LCDC_SEL BIT(0) +#define RK3399_DSI1_LCDC_SEL BIT(4) + +#define RK3399_GRF_SOC_CON22 0x6258 +#define RK3399_DSI0_TURNREQUEST (0xf << 12) +#define RK3399_DSI0_TURNDISABLE (0xf << 8) +#define RK3399_DSI0_FORCETXSTOPMODE (0xf << 4) +#define RK3399_DSI0_FORCERXMODE (0xf << 0) + +#define RK3399_GRF_SOC_CON23 0x625c +#define RK3399_DSI1_TURNDISABLE (0xf << 12) +#define RK3399_DSI1_FORCETXSTOPMODE (0xf << 8) +#define RK3399_DSI1_FORCERXMODE (0xf << 4) +#define RK3399_DSI1_ENABLE (0xf << 0) + +#define RK3399_GRF_SOC_CON24 0x6260 +#define RK3399_TXRX_MASTERSLAVEZ BIT(7) +#define RK3399_TXRX_ENABLECLK BIT(6) +#define RK3399_TXRX_BASEDIR BIT(5) + +#define HIWORD_UPDATE(val, mask) (val | (mask) << 16) + +#define to_dsi(nm) container_of(nm, struct dw_mipi_dsi_rockchip, nm) + +enum { + BANDGAP_97_07, + BANDGAP_98_05, + BANDGAP_99_02, + BANDGAP_100_00, + BANDGAP_93_17, + BANDGAP_94_15, + BANDGAP_95_12, + BANDGAP_96_10, +}; + +enum { + BIASEXTR_87_1, + BIASEXTR_91_5, + BIASEXTR_95_9, + BIASEXTR_100, + BIASEXTR_105_94, + BIASEXTR_111_88, + BIASEXTR_118_8, + BIASEXTR_127_7, +}; + +struct rockchip_dw_dsi_chip_data { + u32 reg; + + u32 lcdsel_grf_reg; + u32 lcdsel_big; + u32 lcdsel_lit; + + u32 enable_grf_reg; + u32 enable; + + u32 lanecfg1_grf_reg; + u32 lanecfg1; + u32 lanecfg2_grf_reg; + u32 lanecfg2; + + unsigned int flags; + unsigned int max_data_lanes; +}; + +struct dw_mipi_dsi_rockchip { + struct device *dev; + struct drm_encoder encoder; + void __iomem *base; + + struct regmap *grf_regmap; + struct clk *pllref_clk; + struct clk *grf_clk; + struct clk *phy_cfg_clk; + + unsigned int lane_mbps; /* per lane */ + u16 input_div; + u16 feedback_div; + u32 format; + + struct dw_mipi_dsi *dmd; + const struct rockchip_dw_dsi_chip_data *cdata; + struct dw_mipi_dsi_plat_data pdata; +}; + +struct dphy_pll_parameter_map { + unsigned int max_mbps; + u8 hsfreqrange; + u8 icpctrl; + u8 lpfctrl; +}; + +/* The table is based on 27MHz DPHY pll reference clock. */ +static const struct dphy_pll_parameter_map dppa_map[] = { + { 89, 0x00, CP_CURRENT_3UA, LPF_RESISTORS_13KOHM }, + { 99, 0x10, CP_CURRENT_3UA, LPF_RESISTORS_13KOHM }, + { 109, 0x20, CP_CURRENT_3UA, LPF_RESISTORS_13KOHM }, + { 129, 0x01, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 139, 0x11, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 149, 0x21, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 169, 0x02, CP_CURRENT_6UA, LPF_RESISTORS_13KOHM }, + { 179, 0x12, CP_CURRENT_6UA, LPF_RESISTORS_13KOHM }, + { 199, 0x22, CP_CURRENT_6UA, LPF_RESISTORS_13KOHM }, + { 219, 0x03, CP_CURRENT_4_5UA, LPF_RESISTORS_13KOHM }, + { 239, 0x13, CP_CURRENT_4_5UA, LPF_RESISTORS_13KOHM }, + { 249, 0x23, CP_CURRENT_4_5UA, LPF_RESISTORS_13KOHM }, + { 269, 0x04, CP_CURRENT_6UA, LPF_RESISTORS_11_5KOHM }, + { 299, 0x14, CP_CURRENT_6UA, LPF_RESISTORS_11_5KOHM }, + { 329, 0x05, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 359, 0x15, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 399, 0x25, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 449, 0x06, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 499, 0x16, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 549, 0x07, CP_CURRENT_7_5UA, LPF_RESISTORS_10_5KOHM }, + { 599, 0x17, CP_CURRENT_7_5UA, LPF_RESISTORS_10_5KOHM }, + { 649, 0x08, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 699, 0x18, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 749, 0x09, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 799, 0x19, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 849, 0x29, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 899, 0x39, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 949, 0x0a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM }, + { 999, 0x1a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM }, + {1049, 0x2a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM }, + {1099, 0x3a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM }, + {1149, 0x0b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1199, 0x1b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1249, 0x2b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1299, 0x3b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1349, 0x0c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1399, 0x1c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1449, 0x2c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1500, 0x3c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM } +}; + +static int max_mbps_to_parameter(unsigned int max_mbps) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(dppa_map); i++) + if (dppa_map[i].max_mbps >= max_mbps) + return i; + + return -EINVAL; +} + +static inline void dsi_write(struct dw_mipi_dsi_rockchip *dsi, u32 reg, u32 val) +{ + writel(val, dsi->base + reg); +} + +static inline u32 dsi_read(struct dw_mipi_dsi_rockchip *dsi, u32 reg) +{ + return readl(dsi->base + reg); +} + +static inline void dsi_set(struct dw_mipi_dsi_rockchip *dsi, u32 reg, u32 mask) +{ + dsi_write(dsi, reg, dsi_read(dsi, reg) | mask); +} + +static inline void dsi_update_bits(struct dw_mipi_dsi_rockchip *dsi, u32 reg, + u32 mask, u32 val) +{ + dsi_write(dsi, reg, (dsi_read(dsi, reg) & ~mask) | val); +} + +static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi_rockchip *dsi, + u8 test_code, + u8 test_data) +{ + /* + * With the falling edge on TESTCLK, the TESTDIN[7:0] signal content + * is latched internally as the current test code. Test data is + * programmed internally by rising edge on TESTCLK. + */ + dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); + + dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_TESTEN | PHY_TESTDOUT(0) | + PHY_TESTDIN(test_code)); + + dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLK | PHY_UNTESTCLR); + + dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_UNTESTEN | PHY_TESTDOUT(0) | + PHY_TESTDIN(test_data)); + + dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); +} + +/** + * ns2bc - Nanoseconds to byte clock cycles + */ +static inline unsigned int ns2bc(struct dw_mipi_dsi_rockchip *dsi, int ns) +{ + return DIV_ROUND_UP(ns * dsi->lane_mbps / 8, 1000); +} + +/** + * ns2ui - Nanoseconds to UI time periods + */ +static inline unsigned int ns2ui(struct dw_mipi_dsi_rockchip *dsi, int ns) +{ + return DIV_ROUND_UP(ns * dsi->lane_mbps, 1000); +} + +static int dw_mipi_dsi_phy_init(void *priv_data) +{ + struct dw_mipi_dsi_rockchip *dsi = priv_data; + int ret, i, vco; + + /* + * Get vco from frequency(lane_mbps) + * vco frequency table + * 000 - between 80 and 200 MHz + * 001 - between 200 and 300 MHz + * 010 - between 300 and 500 MHz + * 011 - between 500 and 700 MHz + * 100 - between 700 and 900 MHz + * 101 - between 900 and 1100 MHz + * 110 - between 1100 and 1300 MHz + * 111 - between 1300 and 1500 MHz + */ + vco = (dsi->lane_mbps < 200) ? 0 : (dsi->lane_mbps + 100) / 200; + + i = max_mbps_to_parameter(dsi->lane_mbps); + if (i < 0) { + DRM_DEV_ERROR(dsi->dev, + "failed to get parameter for %dmbps clock\n", + dsi->lane_mbps); + return i; + } + + ret = clk_prepare_enable(dsi->phy_cfg_clk); + if (ret) { + DRM_DEV_ERROR(dsi->dev, "Failed to enable phy_cfg_clk\n"); + return ret; + } + + dw_mipi_dsi_phy_write(dsi, PLL_BIAS_CUR_SEL_CAP_VCO_CONTROL, + BYPASS_VCO_RANGE | + VCO_RANGE_CON_SEL(vco) | + VCO_IN_CAP_CON_LOW | + REF_BIAS_CUR_SEL); + + dw_mipi_dsi_phy_write(dsi, PLL_CP_CONTROL_PLL_LOCK_BYPASS, + CP_CURRENT_SEL(dppa_map[i].icpctrl)); + dw_mipi_dsi_phy_write(dsi, PLL_LPF_AND_CP_CONTROL, + CP_PROGRAM_EN | LPF_PROGRAM_EN | + LPF_RESISTORS_SEL(dppa_map[i].lpfctrl)); + + dw_mipi_dsi_phy_write(dsi, HS_RX_CONTROL_OF_LANE_0, + HSFREQRANGE_SEL(dppa_map[i].hsfreqrange)); + + dw_mipi_dsi_phy_write(dsi, PLL_INPUT_DIVIDER_RATIO, + INPUT_DIVIDER(dsi->input_div)); + dw_mipi_dsi_phy_write(dsi, PLL_LOOP_DIVIDER_RATIO, + LOOP_DIV_LOW_SEL(dsi->feedback_div) | + LOW_PROGRAM_EN); + /* + * We need set PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL immediately + * to make the configured LSB effective according to IP simulation + * and lab test results. + * Only in this way can we get correct mipi phy pll frequency. + */ + dw_mipi_dsi_phy_write(dsi, PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL, + PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN); + dw_mipi_dsi_phy_write(dsi, PLL_LOOP_DIVIDER_RATIO, + LOOP_DIV_HIGH_SEL(dsi->feedback_div) | + HIGH_PROGRAM_EN); + dw_mipi_dsi_phy_write(dsi, PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL, + PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN); + + dw_mipi_dsi_phy_write(dsi, AFE_BIAS_BANDGAP_ANALOG_PROGRAMMABILITY, + LOW_PROGRAM_EN | BIASEXTR_SEL(BIASEXTR_127_7)); + dw_mipi_dsi_phy_write(dsi, AFE_BIAS_BANDGAP_ANALOG_PROGRAMMABILITY, + HIGH_PROGRAM_EN | BANDGAP_SEL(BANDGAP_96_10)); + + dw_mipi_dsi_phy_write(dsi, BANDGAP_AND_BIAS_CONTROL, + POWER_CONTROL | INTERNAL_REG_CURRENT | + BIAS_BLOCK_ON | BANDGAP_ON); + + dw_mipi_dsi_phy_write(dsi, TERMINATION_RESISTER_CONTROL, + TER_RESISTOR_LOW | TER_CAL_DONE | + SETRD_MAX | TER_RESISTORS_ON); + dw_mipi_dsi_phy_write(dsi, TERMINATION_RESISTER_CONTROL, + TER_RESISTOR_HIGH | LEVEL_SHIFTERS_ON | + SETRD_MAX | POWER_MANAGE | + TER_RESISTORS_ON); + + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_REQUEST_STATE_TIME_CONTROL, + TLP_PROGRAM_EN | ns2bc(dsi, 500)); + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_PREPARE_STATE_TIME_CONTROL, + THS_PRE_PROGRAM_EN | ns2ui(dsi, 40)); + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_HS_ZERO_STATE_TIME_CONTROL, + THS_ZERO_PROGRAM_EN | ns2bc(dsi, 300)); + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_TRAIL_STATE_TIME_CONTROL, + THS_PRE_PROGRAM_EN | ns2ui(dsi, 100)); + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_EXIT_STATE_TIME_CONTROL, + BIT(5) | ns2bc(dsi, 100)); + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_POST_TIME_CONTROL, + BIT(5) | (ns2bc(dsi, 60) + 7)); + + dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_REQUEST_STATE_TIME_CONTROL, + TLP_PROGRAM_EN | ns2bc(dsi, 500)); + dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_PREPARE_STATE_TIME_CONTROL, + THS_PRE_PROGRAM_EN | (ns2ui(dsi, 50) + 20)); + dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_HS_ZERO_STATE_TIME_CONTROL, + THS_ZERO_PROGRAM_EN | (ns2bc(dsi, 140) + 2)); + dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_TRAIL_STATE_TIME_CONTROL, + THS_PRE_PROGRAM_EN | (ns2ui(dsi, 60) + 8)); + dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_EXIT_STATE_TIME_CONTROL, + BIT(5) | ns2bc(dsi, 100)); + + clk_disable_unprepare(dsi->phy_cfg_clk); + + return ret; +} + +static int +dw_mipi_dsi_get_lane_mbps(void *priv_data, struct drm_display_mode *mode, + unsigned long mode_flags, u32 lanes, u32 format, + unsigned int *lane_mbps) +{ + struct dw_mipi_dsi_rockchip *dsi = priv_data; + int bpp; + unsigned long mpclk, tmp; + unsigned int target_mbps = 1000; + unsigned int max_mbps = dppa_map[ARRAY_SIZE(dppa_map) - 1].max_mbps; + unsigned long best_freq = 0; + unsigned long fvco_min, fvco_max, fin, fout; + unsigned int min_prediv, max_prediv; + unsigned int _prediv, uninitialized_var(best_prediv); + unsigned long _fbdiv, uninitialized_var(best_fbdiv); + unsigned long min_delta = ULONG_MAX; + + dsi->format = format; + bpp = mipi_dsi_pixel_format_to_bpp(dsi->format); + if (bpp < 0) { + DRM_DEV_ERROR(dsi->dev, + "failed to get bpp for pixel format %d\n", + dsi->format); + return bpp; + } + + mpclk = DIV_ROUND_UP(mode->clock, MSEC_PER_SEC); + if (mpclk) { + /* take 1 / 0.8, since mbps must big than bandwidth of RGB */ + tmp = mpclk * (bpp / lanes) * 10 / 8; + if (tmp < max_mbps) + target_mbps = tmp; + else + DRM_DEV_ERROR(dsi->dev, + "DPHY clock frequency is out of range\n"); + } + + fin = clk_get_rate(dsi->pllref_clk); + fout = target_mbps * USEC_PER_SEC; + + /* constraint: 5Mhz <= Fref / N <= 40MHz */ + min_prediv = DIV_ROUND_UP(fin, 40 * USEC_PER_SEC); + max_prediv = fin / (5 * USEC_PER_SEC); + + /* constraint: 80MHz <= Fvco <= 1500Mhz */ + fvco_min = 80 * USEC_PER_SEC; + fvco_max = 1500 * USEC_PER_SEC; + + for (_prediv = min_prediv; _prediv <= max_prediv; _prediv++) { + u64 tmp; + u32 delta; + /* Fvco = Fref * M / N */ + tmp = (u64)fout * _prediv; + do_div(tmp, fin); + _fbdiv = tmp; + /* + * Due to the use of a "by 2 pre-scaler," the range of the + * feedback multiplication value M is limited to even division + * numbers, and m must be greater than 6, not bigger than 512. + */ + if (_fbdiv < 6 || _fbdiv > 512) + continue; + + _fbdiv += _fbdiv % 2; + + tmp = (u64)_fbdiv * fin; + do_div(tmp, _prediv); + if (tmp < fvco_min || tmp > fvco_max) + continue; + + delta = abs(fout - tmp); + if (delta < min_delta) { + best_prediv = _prediv; + best_fbdiv = _fbdiv; + min_delta = delta; + best_freq = tmp; + } + } + + if (best_freq) { + dsi->lane_mbps = DIV_ROUND_UP(best_freq, USEC_PER_SEC); + *lane_mbps = dsi->lane_mbps; + dsi->input_div = best_prediv; + dsi->feedback_div = best_fbdiv; + } else { + DRM_DEV_ERROR(dsi->dev, "Can not find best_freq for DPHY\n"); + return -EINVAL; + } + + return 0; +} + +static const struct dw_mipi_dsi_phy_ops dw_mipi_dsi_rockchip_phy_ops = { + .init = dw_mipi_dsi_phy_init, + .get_lane_mbps = dw_mipi_dsi_get_lane_mbps, +}; + +static void dw_mipi_dsi_rockchip_config(struct dw_mipi_dsi_rockchip *dsi, + int mux) +{ + if (dsi->cdata->lcdsel_grf_reg) + regmap_write(dsi->grf_regmap, dsi->cdata->lcdsel_grf_reg, + mux ? dsi->cdata->lcdsel_lit : dsi->cdata->lcdsel_big); + + if (dsi->cdata->lanecfg1_grf_reg) + regmap_write(dsi->grf_regmap, dsi->cdata->lanecfg1_grf_reg, + dsi->cdata->lanecfg1); + + if (dsi->cdata->lanecfg2_grf_reg) + regmap_write(dsi->grf_regmap, dsi->cdata->lanecfg2_grf_reg, + dsi->cdata->lanecfg2); + + if (dsi->cdata->enable_grf_reg) + regmap_write(dsi->grf_regmap, dsi->cdata->enable_grf_reg, + dsi->cdata->enable); +} + +static int +dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder, + struct drm_crtc_state *crtc_state, + struct drm_connector_state *conn_state) +{ + struct rockchip_crtc_state *s = to_rockchip_crtc_state(crtc_state); + struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); + + switch (dsi->format) { + case MIPI_DSI_FMT_RGB888: + s->output_mode = ROCKCHIP_OUT_MODE_P888; + break; + case MIPI_DSI_FMT_RGB666: + s->output_mode = ROCKCHIP_OUT_MODE_P666; + break; + case MIPI_DSI_FMT_RGB565: + s->output_mode = ROCKCHIP_OUT_MODE_P565; + break; + default: + WARN_ON(1); + return -EINVAL; + } + + s->output_type = DRM_MODE_CONNECTOR_DSI; + + return 0; +} + +static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) +{ + struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); + int ret, mux; + + mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, + &dsi->encoder); + if (mux < 0) + return; + + pm_runtime_get_sync(dsi->dev); + + /* + * For the RK3399, the clk of grf must be enabled before writing grf + * register. And for RK3288 or other soc, this grf_clk must be NULL, + * the clk_prepare_enable return true directly. + */ + ret = clk_prepare_enable(dsi->grf_clk); + if (ret) { + DRM_DEV_ERROR(dsi->dev, "Failed to enable grf_clk: %d\n", ret); + return; + } + + dw_mipi_dsi_rockchip_config(dsi, mux); + + clk_disable_unprepare(dsi->grf_clk); +} + +static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) +{ + struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); + + pm_runtime_put(dsi->dev); +} + +static const struct drm_encoder_helper_funcs +dw_mipi_dsi_encoder_helper_funcs = { + .atomic_check = dw_mipi_dsi_encoder_atomic_check, + .enable = dw_mipi_dsi_encoder_enable, + .disable = dw_mipi_dsi_encoder_disable, +}; + +static const struct drm_encoder_funcs dw_mipi_dsi_encoder_funcs = { + .destroy = drm_encoder_cleanup, +}; + +static int rockchip_dsi_drm_create_encoder(struct dw_mipi_dsi_rockchip *dsi, + struct drm_device *drm_dev) +{ + struct drm_encoder *encoder = &dsi->encoder; + int ret; + + encoder->possible_crtcs = drm_of_find_possible_crtcs(drm_dev, + dsi->dev->of_node); + + ret = drm_encoder_init(drm_dev, encoder, &dw_mipi_dsi_encoder_funcs, + DRM_MODE_ENCODER_DSI, NULL); + if (ret) { + DRM_ERROR("Failed to initialize encoder with drm\n"); + return ret; + } + + drm_encoder_helper_add(encoder, &dw_mipi_dsi_encoder_helper_funcs); + + return 0; +} + +static int dw_mipi_dsi_rockchip_bind(struct device *dev, + struct device *master, + void *data) +{ + struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); + struct drm_device *drm_dev = data; + int ret; + + ret = clk_prepare_enable(dsi->pllref_clk); + if (ret) { + DRM_DEV_ERROR(dev, "Failed to enable pllref_clk: %d\n", ret); + return ret; + } + + ret = rockchip_dsi_drm_create_encoder(dsi, drm_dev); + if (ret) { + DRM_DEV_ERROR(dev, "Failed to create drm encoder\n"); + return ret; + } + + ret = dw_mipi_dsi_bind(dsi->dmd, &dsi->encoder); + if (ret) { + DRM_DEV_ERROR(dev, "Failed to bind: %d\n", ret); + return ret; + } + + return 0; +} + +static void dw_mipi_dsi_rockchip_unbind(struct device *dev, + struct device *master, + void *data) +{ + struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); + + dw_mipi_dsi_unbind(dsi->dmd); + + clk_disable_unprepare(dsi->pllref_clk); +} + +static const struct component_ops dw_mipi_dsi_rockchip_ops = { + .bind = dw_mipi_dsi_rockchip_bind, + .unbind = dw_mipi_dsi_rockchip_unbind, +}; + +static int dw_mipi_dsi_rockchip_host_attach(void *priv_data, + struct mipi_dsi_device *device) +{ + struct dw_mipi_dsi_rockchip *dsi = priv_data; + int ret; + + ret = component_add(dsi->dev, &dw_mipi_dsi_rockchip_ops); + if (ret) { + DRM_DEV_ERROR(dsi->dev, "Failed to register component: %d\n", + ret); + return ret; + } + + return 0; +} + +static int dw_mipi_dsi_rockchip_host_detach(void *priv_data, + struct mipi_dsi_device *device) +{ + struct dw_mipi_dsi_rockchip *dsi = priv_data; + + component_del(dsi->dev, &dw_mipi_dsi_rockchip_ops); + + return 0; +} + +static const struct dw_mipi_dsi_host_ops dw_mipi_dsi_rockchip_host_ops = { + .attach = dw_mipi_dsi_rockchip_host_attach, + .detach = dw_mipi_dsi_rockchip_host_detach, +}; + +static int dw_mipi_dsi_rockchip_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct dw_mipi_dsi_rockchip *dsi; + struct resource *res; + const struct rockchip_dw_dsi_chip_data *cdata = + of_device_get_match_data(dev); + int ret, i; + + dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL); + if (!dsi) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + dsi->base = devm_ioremap_resource(dev, res); + if (IS_ERR(dsi->base)) { + DRM_DEV_ERROR(dev, "Unable to get dsi registers\n"); + return PTR_ERR(dsi->base); + } + + i = 0; + while (cdata[i].reg) { + if (cdata[i].reg == res->start) { + dsi->cdata = &cdata[i]; + break; + } + + i++; + } + + if (!dsi->cdata) { + dev_err(dev, "no dsi-config for %s node\n", np->name); + return -EINVAL; + } + + dsi->pllref_clk = devm_clk_get(dev, "ref"); + if (IS_ERR(dsi->pllref_clk)) { + ret = PTR_ERR(dsi->pllref_clk); + DRM_DEV_ERROR(dev, + "Unable to get pll reference clock: %d\n", ret); + return ret; + } + + if (dsi->cdata->flags & DW_MIPI_NEEDS_PHY_CFG_CLK) { + dsi->phy_cfg_clk = devm_clk_get(dev, "phy_cfg"); + if (IS_ERR(dsi->phy_cfg_clk)) { + ret = PTR_ERR(dsi->phy_cfg_clk); + DRM_DEV_ERROR(dev, + "Unable to get phy_cfg_clk: %d\n", ret); + return ret; + } + } + + if (dsi->cdata->flags & DW_MIPI_NEEDS_GRF_CLK) { + dsi->grf_clk = devm_clk_get(dev, "grf"); + if (IS_ERR(dsi->grf_clk)) { + ret = PTR_ERR(dsi->grf_clk); + DRM_DEV_ERROR(dev, "Unable to get grf_clk: %d\n", ret); + return ret; + } + } + + dsi->grf_regmap = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); + if (IS_ERR(dsi->grf_regmap)) { + DRM_DEV_ERROR(dsi->dev, "Unable to get rockchip,grf\n"); + return PTR_ERR(dsi->grf_regmap); + } + + dsi->dev = dev; + dsi->pdata.base = dsi->base; + dsi->pdata.max_data_lanes = dsi->cdata->max_data_lanes; + dsi->pdata.phy_ops = &dw_mipi_dsi_rockchip_phy_ops; + dsi->pdata.host_ops = &dw_mipi_dsi_rockchip_host_ops; + dsi->pdata.priv_data = dsi; + platform_set_drvdata(pdev, dsi); + + dsi->dmd = dw_mipi_dsi_probe(pdev, &dsi->pdata); + if (IS_ERR(dsi->dmd)) { + ret = PTR_ERR(dsi->dmd); + if (ret != -EPROBE_DEFER) + DRM_DEV_ERROR(dev, + "Failed to probe dw_mipi_dsi: %d\n", ret); + goto err_clkdisable; + } + + return 0; + +err_clkdisable: + clk_disable_unprepare(dsi->pllref_clk); + return ret; +} + +static int dw_mipi_dsi_rockchip_remove(struct platform_device *pdev) +{ + struct dw_mipi_dsi_rockchip *dsi = platform_get_drvdata(pdev); + + dw_mipi_dsi_remove(dsi->dmd); + + return 0; +} + +static const struct rockchip_dw_dsi_chip_data rk3288_chip_data[] = { + { + .reg = 0xff960000, + .lcdsel_grf_reg = RK3288_GRF_SOC_CON6, + .lcdsel_big = HIWORD_UPDATE(0, RK3288_DSI0_LCDC_SEL), + .lcdsel_lit = HIWORD_UPDATE(RK3288_DSI0_LCDC_SEL, RK3288_DSI0_LCDC_SEL), + + .max_data_lanes = 4, + }, + { + .reg = 0xff964000, + .lcdsel_grf_reg = RK3288_GRF_SOC_CON6, + .lcdsel_big = HIWORD_UPDATE(0, RK3288_DSI1_LCDC_SEL), + .lcdsel_lit = HIWORD_UPDATE(RK3288_DSI1_LCDC_SEL, RK3288_DSI1_LCDC_SEL), + + .max_data_lanes = 4, + }, + { /* sentinel */ } +}; + +static const struct rockchip_dw_dsi_chip_data rk3399_chip_data[] = { + { + .reg = 0xff960000, + .lcdsel_grf_reg = RK3399_GRF_SOC_CON20, + .lcdsel_big = HIWORD_UPDATE(0, RK3399_DSI0_LCDC_SEL), + .lcdsel_lit = HIWORD_UPDATE(RK3399_DSI0_LCDC_SEL, + RK3399_DSI0_LCDC_SEL), + + .lanecfg1_grf_reg = RK3399_GRF_SOC_CON22, + .lanecfg1 = HIWORD_UPDATE(0, RK3399_DSI0_TURNREQUEST | + RK3399_DSI0_TURNDISABLE | + RK3399_DSI0_FORCETXSTOPMODE | + RK3399_DSI0_FORCERXMODE), + + .flags = DW_MIPI_NEEDS_PHY_CFG_CLK | DW_MIPI_NEEDS_GRF_CLK, + .max_data_lanes = 4, + }, + { + .reg = 0xff968000, + .lcdsel_grf_reg = RK3399_GRF_SOC_CON20, + .lcdsel_big = HIWORD_UPDATE(0, RK3399_DSI1_LCDC_SEL), + .lcdsel_lit = HIWORD_UPDATE(RK3399_DSI1_LCDC_SEL, + RK3399_DSI1_LCDC_SEL), + + .lanecfg1_grf_reg = RK3399_GRF_SOC_CON23, + .lanecfg1 = HIWORD_UPDATE(0, RK3399_DSI1_TURNDISABLE | + RK3399_DSI1_FORCETXSTOPMODE | + RK3399_DSI1_FORCERXMODE | + RK3399_DSI1_ENABLE), + + .lanecfg2_grf_reg = RK3399_GRF_SOC_CON24, + .lanecfg2 = HIWORD_UPDATE(RK3399_TXRX_MASTERSLAVEZ | + RK3399_TXRX_ENABLECLK, + RK3399_TXRX_MASTERSLAVEZ | + RK3399_TXRX_ENABLECLK | + RK3399_TXRX_BASEDIR), + + .enable_grf_reg = RK3399_GRF_SOC_CON23, + .enable = HIWORD_UPDATE(RK3399_DSI1_ENABLE, RK3399_DSI1_ENABLE), + + .flags = DW_MIPI_NEEDS_PHY_CFG_CLK | DW_MIPI_NEEDS_GRF_CLK, + .max_data_lanes = 4, + }, + { /* sentinel */ } +}; + +static const struct of_device_id dw_mipi_dsi_rockchip_dt_ids[] = { + { + .compatible = "rockchip,rk3288-mipi-dsi", + .data = &rk3288_chip_data, + }, { + .compatible = "rockchip,rk3399-mipi-dsi", + .data = &rk3399_chip_data, + }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, dw_mipi_dsi_rockchip_dt_ids); + +struct platform_driver dw_mipi_dsi_rockchip_driver = { + .probe = dw_mipi_dsi_rockchip_probe, + .remove = dw_mipi_dsi_rockchip_remove, + .driver = { + .of_match_table = dw_mipi_dsi_rockchip_dt_ids, + .name = "dw-mipi-dsi-rockchip", + }, +}; diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c deleted file mode 100644 index 662b6cb5d3f0..000000000000 --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c +++ /dev/null @@ -1,1349 +0,0 @@ -/* - * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ -#include <linux/clk.h> -#include <linux/component.h> -#include <linux/iopoll.h> -#include <linux/math64.h> -#include <linux/module.h> -#include <linux/of_device.h> -#include <linux/pm_runtime.h> -#include <linux/regmap.h> -#include <linux/reset.h> -#include <linux/mfd/syscon.h> -#include <drm/drm_atomic_helper.h> -#include <drm/drm_crtc.h> -#include <drm/drm_crtc_helper.h> -#include <drm/drm_mipi_dsi.h> -#include <drm/drm_of.h> -#include <drm/drm_panel.h> -#include <drm/drmP.h> -#include <video/mipi_display.h> - -#include "rockchip_drm_drv.h" -#include "rockchip_drm_vop.h" - -#define DRIVER_NAME "dw-mipi-dsi" - -#define RK3288_GRF_SOC_CON6 0x025c -#define RK3288_DSI0_SEL_VOP_LIT BIT(6) -#define RK3288_DSI1_SEL_VOP_LIT BIT(9) - -#define RK3399_GRF_SOC_CON20 0x6250 -#define RK3399_DSI0_SEL_VOP_LIT BIT(0) -#define RK3399_DSI1_SEL_VOP_LIT BIT(4) - -/* disable turnrequest, turndisable, forcetxstopmode, forcerxmode */ -#define RK3399_GRF_SOC_CON22 0x6258 -#define RK3399_GRF_DSI_MODE 0xffff0000 - -#define DSI_VERSION 0x00 -#define DSI_PWR_UP 0x04 -#define RESET 0 -#define POWERUP BIT(0) - -#define DSI_CLKMGR_CFG 0x08 -#define TO_CLK_DIVIDSION(div) (((div) & 0xff) << 8) -#define TX_ESC_CLK_DIVIDSION(div) (((div) & 0xff) << 0) - -#define DSI_DPI_VCID 0x0c -#define DPI_VID(vid) (((vid) & 0x3) << 0) - -#define DSI_DPI_COLOR_CODING 0x10 -#define EN18_LOOSELY BIT(8) -#define DPI_COLOR_CODING_16BIT_1 0x0 -#define DPI_COLOR_CODING_16BIT_2 0x1 -#define DPI_COLOR_CODING_16BIT_3 0x2 -#define DPI_COLOR_CODING_18BIT_1 0x3 -#define DPI_COLOR_CODING_18BIT_2 0x4 -#define DPI_COLOR_CODING_24BIT 0x5 - -#define DSI_DPI_CFG_POL 0x14 -#define COLORM_ACTIVE_LOW BIT(4) -#define SHUTD_ACTIVE_LOW BIT(3) -#define HSYNC_ACTIVE_LOW BIT(2) -#define VSYNC_ACTIVE_LOW BIT(1) -#define DATAEN_ACTIVE_LOW BIT(0) - -#define DSI_DPI_LP_CMD_TIM 0x18 -#define OUTVACT_LPCMD_TIME(p) (((p) & 0xff) << 16) -#define INVACT_LPCMD_TIME(p) ((p) & 0xff) - -#define DSI_DBI_CFG 0x20 -#define DSI_DBI_CMDSIZE 0x28 - -#define DSI_PCKHDL_CFG 0x2c -#define EN_CRC_RX BIT(4) -#define EN_ECC_RX BIT(3) -#define EN_BTA BIT(2) -#define EN_EOTP_RX BIT(1) -#define EN_EOTP_TX BIT(0) - -#define DSI_MODE_CFG 0x34 -#define ENABLE_VIDEO_MODE 0 -#define ENABLE_CMD_MODE BIT(0) - -#define DSI_VID_MODE_CFG 0x38 -#define FRAME_BTA_ACK BIT(14) -#define ENABLE_LOW_POWER (0x3f << 8) -#define ENABLE_LOW_POWER_MASK (0x3f << 8) -#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES 0x0 -#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS 0x1 -#define VID_MODE_TYPE_BURST 0x2 -#define VID_MODE_TYPE_MASK 0x3 - -#define DSI_VID_PKT_SIZE 0x3c -#define VID_PKT_SIZE(p) (((p) & 0x3fff) << 0) -#define VID_PKT_MAX_SIZE 0x3fff - -#define DSI_VID_HSA_TIME 0x48 -#define DSI_VID_HBP_TIME 0x4c -#define DSI_VID_HLINE_TIME 0x50 -#define DSI_VID_VSA_LINES 0x54 -#define DSI_VID_VBP_LINES 0x58 -#define DSI_VID_VFP_LINES 0x5c -#define DSI_VID_VACTIVE_LINES 0x60 -#define DSI_CMD_MODE_CFG 0x68 -#define MAX_RD_PKT_SIZE_LP BIT(24) -#define DCS_LW_TX_LP BIT(19) -#define DCS_SR_0P_TX_LP BIT(18) -#define DCS_SW_1P_TX_LP BIT(17) -#define DCS_SW_0P_TX_LP BIT(16) -#define GEN_LW_TX_LP BIT(14) -#define GEN_SR_2P_TX_LP BIT(13) -#define GEN_SR_1P_TX_LP BIT(12) -#define GEN_SR_0P_TX_LP BIT(11) -#define GEN_SW_2P_TX_LP BIT(10) -#define GEN_SW_1P_TX_LP BIT(9) -#define GEN_SW_0P_TX_LP BIT(8) -#define EN_ACK_RQST BIT(1) -#define EN_TEAR_FX BIT(0) - -#define CMD_MODE_ALL_LP (MAX_RD_PKT_SIZE_LP | \ - DCS_LW_TX_LP | \ - DCS_SR_0P_TX_LP | \ - DCS_SW_1P_TX_LP | \ - DCS_SW_0P_TX_LP | \ - GEN_LW_TX_LP | \ - GEN_SR_2P_TX_LP | \ - GEN_SR_1P_TX_LP | \ - GEN_SR_0P_TX_LP | \ - GEN_SW_2P_TX_LP | \ - GEN_SW_1P_TX_LP | \ - GEN_SW_0P_TX_LP) - -#define DSI_GEN_HDR 0x6c -#define GEN_HDATA(data) (((data) & 0xffff) << 8) -#define GEN_HDATA_MASK (0xffff << 8) -#define GEN_HTYPE(type) (((type) & 0xff) << 0) -#define GEN_HTYPE_MASK 0xff - -#define DSI_GEN_PLD_DATA 0x70 - -#define DSI_CMD_PKT_STATUS 0x74 -#define GEN_CMD_EMPTY BIT(0) -#define GEN_CMD_FULL BIT(1) -#define GEN_PLD_W_EMPTY BIT(2) -#define GEN_PLD_W_FULL BIT(3) -#define GEN_PLD_R_EMPTY BIT(4) -#define GEN_PLD_R_FULL BIT(5) -#define GEN_RD_CMD_BUSY BIT(6) - -#define DSI_TO_CNT_CFG 0x78 -#define HSTX_TO_CNT(p) (((p) & 0xffff) << 16) -#define LPRX_TO_CNT(p) ((p) & 0xffff) - -#define DSI_BTA_TO_CNT 0x8c -#define DSI_LPCLK_CTRL 0x94 -#define AUTO_CLKLANE_CTRL BIT(1) -#define PHY_TXREQUESTCLKHS BIT(0) - -#define DSI_PHY_TMR_LPCLK_CFG 0x98 -#define PHY_CLKHS2LP_TIME(lbcc) (((lbcc) & 0x3ff) << 16) -#define PHY_CLKLP2HS_TIME(lbcc) ((lbcc) & 0x3ff) - -#define DSI_PHY_TMR_CFG 0x9c -#define PHY_HS2LP_TIME(lbcc) (((lbcc) & 0xff) << 24) -#define PHY_LP2HS_TIME(lbcc) (((lbcc) & 0xff) << 16) -#define MAX_RD_TIME(lbcc) ((lbcc) & 0x7fff) - -#define DSI_PHY_RSTZ 0xa0 -#define PHY_DISFORCEPLL 0 -#define PHY_ENFORCEPLL BIT(3) -#define PHY_DISABLECLK 0 -#define PHY_ENABLECLK BIT(2) -#define PHY_RSTZ 0 -#define PHY_UNRSTZ BIT(1) -#define PHY_SHUTDOWNZ 0 -#define PHY_UNSHUTDOWNZ BIT(0) - -#define DSI_PHY_IF_CFG 0xa4 -#define N_LANES(n) ((((n) - 1) & 0x3) << 0) -#define PHY_STOP_WAIT_TIME(cycle) (((cycle) & 0xff) << 8) - -#define DSI_PHY_STATUS 0xb0 -#define LOCK BIT(0) -#define STOP_STATE_CLK_LANE BIT(2) - -#define DSI_PHY_TST_CTRL0 0xb4 -#define PHY_TESTCLK BIT(1) -#define PHY_UNTESTCLK 0 -#define PHY_TESTCLR BIT(0) -#define PHY_UNTESTCLR 0 - -#define DSI_PHY_TST_CTRL1 0xb8 -#define PHY_TESTEN BIT(16) -#define PHY_UNTESTEN 0 -#define PHY_TESTDOUT(n) (((n) & 0xff) << 8) -#define PHY_TESTDIN(n) (((n) & 0xff) << 0) - -#define DSI_INT_ST0 0xbc -#define DSI_INT_ST1 0xc0 -#define DSI_INT_MSK0 0xc4 -#define DSI_INT_MSK1 0xc8 - -#define PHY_STATUS_TIMEOUT_US 10000 -#define CMD_PKT_STATUS_TIMEOUT_US 20000 - -#define BYPASS_VCO_RANGE BIT(7) -#define VCO_RANGE_CON_SEL(val) (((val) & 0x7) << 3) -#define VCO_IN_CAP_CON_DEFAULT (0x0 << 1) -#define VCO_IN_CAP_CON_LOW (0x1 << 1) -#define VCO_IN_CAP_CON_HIGH (0x2 << 1) -#define REF_BIAS_CUR_SEL BIT(0) - -#define CP_CURRENT_3MA BIT(3) -#define CP_PROGRAM_EN BIT(7) -#define LPF_PROGRAM_EN BIT(6) -#define LPF_RESISTORS_20_KOHM 0 - -#define HSFREQRANGE_SEL(val) (((val) & 0x3f) << 1) - -#define INPUT_DIVIDER(val) (((val) - 1) & 0x7f) -#define LOW_PROGRAM_EN 0 -#define HIGH_PROGRAM_EN BIT(7) -#define LOOP_DIV_LOW_SEL(val) (((val) - 1) & 0x1f) -#define LOOP_DIV_HIGH_SEL(val) ((((val) - 1) >> 5) & 0x1f) -#define PLL_LOOP_DIV_EN BIT(5) -#define PLL_INPUT_DIV_EN BIT(4) - -#define POWER_CONTROL BIT(6) -#define INTERNAL_REG_CURRENT BIT(3) -#define BIAS_BLOCK_ON BIT(2) -#define BANDGAP_ON BIT(0) - -#define TER_RESISTOR_HIGH BIT(7) -#define TER_RESISTOR_LOW 0 -#define LEVEL_SHIFTERS_ON BIT(6) -#define TER_CAL_DONE BIT(5) -#define SETRD_MAX (0x7 << 2) -#define POWER_MANAGE BIT(1) -#define TER_RESISTORS_ON BIT(0) - -#define BIASEXTR_SEL(val) ((val) & 0x7) -#define BANDGAP_SEL(val) ((val) & 0x7) -#define TLP_PROGRAM_EN BIT(7) -#define THS_PRE_PROGRAM_EN BIT(7) -#define THS_ZERO_PROGRAM_EN BIT(6) - -#define DW_MIPI_NEEDS_PHY_CFG_CLK BIT(0) -#define DW_MIPI_NEEDS_GRF_CLK BIT(1) - -enum { - BANDGAP_97_07, - BANDGAP_98_05, - BANDGAP_99_02, - BANDGAP_100_00, - BANDGAP_93_17, - BANDGAP_94_15, - BANDGAP_95_12, - BANDGAP_96_10, -}; - -enum { - BIASEXTR_87_1, - BIASEXTR_91_5, - BIASEXTR_95_9, - BIASEXTR_100, - BIASEXTR_105_94, - BIASEXTR_111_88, - BIASEXTR_118_8, - BIASEXTR_127_7, -}; - -struct dw_mipi_dsi_plat_data { - u32 dsi0_en_bit; - u32 dsi1_en_bit; - u32 grf_switch_reg; - u32 grf_dsi0_mode; - u32 grf_dsi0_mode_reg; - unsigned int flags; - unsigned int max_data_lanes; -}; - -struct dw_mipi_dsi { - struct drm_encoder encoder; - struct drm_connector connector; - struct mipi_dsi_host dsi_host; - struct drm_panel *panel; - struct device *dev; - struct regmap *grf_regmap; - void __iomem *base; - - struct clk *grf_clk; - struct clk *pllref_clk; - struct clk *pclk; - struct clk *phy_cfg_clk; - - int dpms_mode; - unsigned int lane_mbps; /* per lane */ - u32 channel; - u32 lanes; - u32 format; - u16 input_div; - u16 feedback_div; - unsigned long mode_flags; - - const struct dw_mipi_dsi_plat_data *pdata; -}; - -enum dw_mipi_dsi_mode { - DW_MIPI_DSI_CMD_MODE, - DW_MIPI_DSI_VID_MODE, -}; - -struct dphy_pll_testdin_map { - unsigned int max_mbps; - u8 testdin; -}; - -/* The table is based on 27MHz DPHY pll reference clock. */ -static const struct dphy_pll_testdin_map dptdin_map[] = { - { 90, 0x00}, { 100, 0x10}, { 110, 0x20}, { 130, 0x01}, - { 140, 0x11}, { 150, 0x21}, { 170, 0x02}, { 180, 0x12}, - { 200, 0x22}, { 220, 0x03}, { 240, 0x13}, { 250, 0x23}, - { 270, 0x04}, { 300, 0x14}, { 330, 0x05}, { 360, 0x15}, - { 400, 0x25}, { 450, 0x06}, { 500, 0x16}, { 550, 0x07}, - { 600, 0x17}, { 650, 0x08}, { 700, 0x18}, { 750, 0x09}, - { 800, 0x19}, { 850, 0x29}, { 900, 0x39}, { 950, 0x0a}, - {1000, 0x1a}, {1050, 0x2a}, {1100, 0x3a}, {1150, 0x0b}, - {1200, 0x1b}, {1250, 0x2b}, {1300, 0x3b}, {1350, 0x0c}, - {1400, 0x1c}, {1450, 0x2c}, {1500, 0x3c} -}; - -static int max_mbps_to_testdin(unsigned int max_mbps) -{ - int i; - - for (i = 0; i < ARRAY_SIZE(dptdin_map); i++) - if (dptdin_map[i].max_mbps > max_mbps) - return dptdin_map[i].testdin; - - return -EINVAL; -} - -/* - * The controller should generate 2 frames before - * preparing the peripheral. - */ -static void dw_mipi_dsi_wait_for_two_frames(struct drm_display_mode *mode) -{ - int refresh, two_frames; - - refresh = drm_mode_vrefresh(mode); - two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2; - msleep(two_frames); -} - -static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host) -{ - return container_of(host, struct dw_mipi_dsi, dsi_host); -} - -static inline struct dw_mipi_dsi *con_to_dsi(struct drm_connector *con) -{ - return container_of(con, struct dw_mipi_dsi, connector); -} - -static inline struct dw_mipi_dsi *encoder_to_dsi(struct drm_encoder *encoder) -{ - return container_of(encoder, struct dw_mipi_dsi, encoder); -} - -static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val) -{ - writel(val, dsi->base + reg); -} - -static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg) -{ - return readl(dsi->base + reg); -} - -static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi *dsi, u8 test_code, - u8 test_data) -{ - /* - * With the falling edge on TESTCLK, the TESTDIN[7:0] signal content - * is latched internally as the current test code. Test data is - * programmed internally by rising edge on TESTCLK. - */ - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); - - dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_TESTEN | PHY_TESTDOUT(0) | - PHY_TESTDIN(test_code)); - - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLK | PHY_UNTESTCLR); - - dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_UNTESTEN | PHY_TESTDOUT(0) | - PHY_TESTDIN(test_data)); - - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); -} - -/** - * ns2bc - Nanoseconds to byte clock cycles - */ -static inline unsigned int ns2bc(struct dw_mipi_dsi *dsi, int ns) -{ - return DIV_ROUND_UP(ns * dsi->lane_mbps / 8, 1000); -} - -/** - * ns2ui - Nanoseconds to UI time periods - */ -static inline unsigned int ns2ui(struct dw_mipi_dsi *dsi, int ns) -{ - return DIV_ROUND_UP(ns * dsi->lane_mbps, 1000); -} - -static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi) -{ - int ret, testdin, vco, val; - - vco = (dsi->lane_mbps < 200) ? 0 : (dsi->lane_mbps + 100) / 200; - - testdin = max_mbps_to_testdin(dsi->lane_mbps); - if (testdin < 0) { - DRM_DEV_ERROR(dsi->dev, - "failed to get testdin for %dmbps lane clock\n", - dsi->lane_mbps); - return testdin; - } - - /* Start by clearing PHY state */ - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR); - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR); - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR); - - ret = clk_prepare_enable(dsi->phy_cfg_clk); - if (ret) { - DRM_DEV_ERROR(dsi->dev, "Failed to enable phy_cfg_clk\n"); - return ret; - } - - dw_mipi_dsi_phy_write(dsi, 0x10, BYPASS_VCO_RANGE | - VCO_RANGE_CON_SEL(vco) | - VCO_IN_CAP_CON_LOW | - REF_BIAS_CUR_SEL); - - dw_mipi_dsi_phy_write(dsi, 0x11, CP_CURRENT_3MA); - dw_mipi_dsi_phy_write(dsi, 0x12, CP_PROGRAM_EN | LPF_PROGRAM_EN | - LPF_RESISTORS_20_KOHM); - - dw_mipi_dsi_phy_write(dsi, 0x44, HSFREQRANGE_SEL(testdin)); - - dw_mipi_dsi_phy_write(dsi, 0x17, INPUT_DIVIDER(dsi->input_div)); - dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_LOW_SEL(dsi->feedback_div) | - LOW_PROGRAM_EN); - dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_HIGH_SEL(dsi->feedback_div) | - HIGH_PROGRAM_EN); - dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN); - - dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN | - BIASEXTR_SEL(BIASEXTR_127_7)); - dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN | - BANDGAP_SEL(BANDGAP_96_10)); - - dw_mipi_dsi_phy_write(dsi, 0x20, POWER_CONTROL | INTERNAL_REG_CURRENT | - BIAS_BLOCK_ON | BANDGAP_ON); - - dw_mipi_dsi_phy_write(dsi, 0x21, TER_RESISTOR_LOW | TER_CAL_DONE | - SETRD_MAX | TER_RESISTORS_ON); - dw_mipi_dsi_phy_write(dsi, 0x21, TER_RESISTOR_HIGH | LEVEL_SHIFTERS_ON | - SETRD_MAX | POWER_MANAGE | - TER_RESISTORS_ON); - - dw_mipi_dsi_phy_write(dsi, 0x60, TLP_PROGRAM_EN | ns2bc(dsi, 500)); - dw_mipi_dsi_phy_write(dsi, 0x61, THS_PRE_PROGRAM_EN | ns2ui(dsi, 40)); - dw_mipi_dsi_phy_write(dsi, 0x62, THS_ZERO_PROGRAM_EN | ns2bc(dsi, 300)); - dw_mipi_dsi_phy_write(dsi, 0x63, THS_PRE_PROGRAM_EN | ns2ui(dsi, 100)); - dw_mipi_dsi_phy_write(dsi, 0x64, BIT(5) | ns2bc(dsi, 100)); - dw_mipi_dsi_phy_write(dsi, 0x65, BIT(5) | (ns2bc(dsi, 60) + 7)); - - dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | ns2bc(dsi, 500)); - dw_mipi_dsi_phy_write(dsi, 0x71, - THS_PRE_PROGRAM_EN | (ns2ui(dsi, 50) + 5)); - dw_mipi_dsi_phy_write(dsi, 0x72, - THS_ZERO_PROGRAM_EN | (ns2bc(dsi, 140) + 2)); - dw_mipi_dsi_phy_write(dsi, 0x73, - THS_PRE_PROGRAM_EN | (ns2ui(dsi, 60) + 8)); - dw_mipi_dsi_phy_write(dsi, 0x74, BIT(5) | ns2bc(dsi, 100)); - - dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK | - PHY_UNRSTZ | PHY_UNSHUTDOWNZ); - - ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS, - val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US); - if (ret < 0) { - DRM_DEV_ERROR(dsi->dev, "failed to wait for phy lock state\n"); - goto phy_init_end; - } - - ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS, - val, val & STOP_STATE_CLK_LANE, 1000, - PHY_STATUS_TIMEOUT_US); - if (ret < 0) - DRM_DEV_ERROR(dsi->dev, - "failed to wait for phy clk lane stop state\n"); - -phy_init_end: - clk_disable_unprepare(dsi->phy_cfg_clk); - - return ret; -} - -static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode) -{ - unsigned int i, pre; - unsigned long mpclk, pllref, tmp; - unsigned int m = 1, n = 1, target_mbps = 1000; - unsigned int max_mbps = dptdin_map[ARRAY_SIZE(dptdin_map) - 1].max_mbps; - int bpp; - - bpp = mipi_dsi_pixel_format_to_bpp(dsi->format); - if (bpp < 0) { - DRM_DEV_ERROR(dsi->dev, - "failed to get bpp for pixel format %d\n", - dsi->format); - return bpp; - } - - mpclk = DIV_ROUND_UP(mode->clock, MSEC_PER_SEC); - if (mpclk) { - /* take 1 / 0.8, since mbps must big than bandwidth of RGB */ - tmp = mpclk * (bpp / dsi->lanes) * 10 / 8; - if (tmp < max_mbps) - target_mbps = tmp; - else - DRM_DEV_ERROR(dsi->dev, - "DPHY clock frequency is out of range\n"); - } - - pllref = DIV_ROUND_UP(clk_get_rate(dsi->pllref_clk), USEC_PER_SEC); - tmp = pllref; - - /* - * The limits on the PLL divisor are: - * - * 5MHz <= (pllref / n) <= 40MHz - * - * we walk over these values in descreasing order so that if we hit - * an exact match for target_mbps it is more likely that "m" will be - * even. - * - * TODO: ensure that "m" is even after this loop. - */ - for (i = pllref / 5; i > (pllref / 40); i--) { - pre = pllref / i; - if ((tmp > (target_mbps % pre)) && (target_mbps / pre < 512)) { - tmp = target_mbps % pre; - n = i; - m = target_mbps / pre; - } - if (tmp == 0) - break; - } - - dsi->lane_mbps = pllref / n * m; - dsi->input_div = n; - dsi->feedback_div = m; - - return 0; -} - -static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host, - struct mipi_dsi_device *device) -{ - struct dw_mipi_dsi *dsi = host_to_dsi(host); - - if (device->lanes > dsi->pdata->max_data_lanes) { - DRM_DEV_ERROR(dsi->dev, - "the number of data lanes(%u) is too many\n", - device->lanes); - return -EINVAL; - } - - dsi->lanes = device->lanes; - dsi->channel = device->channel; - dsi->format = device->format; - dsi->mode_flags = device->mode_flags; - dsi->panel = of_drm_find_panel(device->dev.of_node); - if (!IS_ERR(dsi->panel)) - return drm_panel_attach(dsi->panel, &dsi->connector); - - return -EINVAL; -} - -static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host, - struct mipi_dsi_device *device) -{ - struct dw_mipi_dsi *dsi = host_to_dsi(host); - - drm_panel_detach(dsi->panel); - - return 0; -} - -static void dw_mipi_message_config(struct dw_mipi_dsi *dsi, - const struct mipi_dsi_msg *msg) -{ - bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM; - u32 val = 0; - - if (msg->flags & MIPI_DSI_MSG_REQ_ACK) - val |= EN_ACK_RQST; - if (lpm) - val |= CMD_MODE_ALL_LP; - - dsi_write(dsi, DSI_LPCLK_CTRL, lpm ? 0 : PHY_TXREQUESTCLKHS); - dsi_write(dsi, DSI_CMD_MODE_CFG, val); -} - -static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val) -{ - int ret; - u32 val, mask; - - ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS, - val, !(val & GEN_CMD_FULL), 1000, - CMD_PKT_STATUS_TIMEOUT_US); - if (ret < 0) { - DRM_DEV_ERROR(dsi->dev, - "failed to get available command FIFO\n"); - return ret; - } - - dsi_write(dsi, DSI_GEN_HDR, hdr_val); - - mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY; - ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS, - val, (val & mask) == mask, - 1000, CMD_PKT_STATUS_TIMEOUT_US); - if (ret < 0) { - DRM_DEV_ERROR(dsi->dev, "failed to write command FIFO\n"); - return ret; - } - - return 0; -} - -static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi, - const struct mipi_dsi_msg *msg) -{ - const u8 *tx_buf = msg->tx_buf; - u16 data = 0; - u32 val; - - if (msg->tx_len > 0) - data |= tx_buf[0]; - if (msg->tx_len > 1) - data |= tx_buf[1] << 8; - - if (msg->tx_len > 2) { - DRM_DEV_ERROR(dsi->dev, - "too long tx buf length %zu for short write\n", - msg->tx_len); - return -EINVAL; - } - - val = GEN_HDATA(data) | GEN_HTYPE(msg->type); - return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val); -} - -static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi, - const struct mipi_dsi_msg *msg) -{ - const u8 *tx_buf = msg->tx_buf; - int len = msg->tx_len, pld_data_bytes = sizeof(u32), ret; - u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type); - u32 remainder; - u32 val; - - if (msg->tx_len < 3) { - DRM_DEV_ERROR(dsi->dev, - "wrong tx buf length %zu for long write\n", - msg->tx_len); - return -EINVAL; - } - - while (DIV_ROUND_UP(len, pld_data_bytes)) { - if (len < pld_data_bytes) { - remainder = 0; - memcpy(&remainder, tx_buf, len); - dsi_write(dsi, DSI_GEN_PLD_DATA, remainder); - len = 0; - } else { - memcpy(&remainder, tx_buf, pld_data_bytes); - dsi_write(dsi, DSI_GEN_PLD_DATA, remainder); - tx_buf += pld_data_bytes; - len -= pld_data_bytes; - } - - ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS, - val, !(val & GEN_PLD_W_FULL), 1000, - CMD_PKT_STATUS_TIMEOUT_US); - if (ret < 0) { - DRM_DEV_ERROR(dsi->dev, - "failed to get available write payload FIFO\n"); - return ret; - } - } - - return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val); -} - -static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host, - const struct mipi_dsi_msg *msg) -{ - struct dw_mipi_dsi *dsi = host_to_dsi(host); - int ret; - - dw_mipi_message_config(dsi, msg); - - switch (msg->type) { - case MIPI_DSI_DCS_SHORT_WRITE: - case MIPI_DSI_DCS_SHORT_WRITE_PARAM: - case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE: - ret = dw_mipi_dsi_dcs_short_write(dsi, msg); - break; - case MIPI_DSI_DCS_LONG_WRITE: - ret = dw_mipi_dsi_dcs_long_write(dsi, msg); - break; - default: - DRM_DEV_ERROR(dsi->dev, "unsupported message type 0x%02x\n", - msg->type); - ret = -EINVAL; - } - - return ret; -} - -static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = { - .attach = dw_mipi_dsi_host_attach, - .detach = dw_mipi_dsi_host_detach, - .transfer = dw_mipi_dsi_host_transfer, -}; - -static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi) -{ - u32 val; - - val = ENABLE_LOW_POWER; - - if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) - val |= VID_MODE_TYPE_BURST; - else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE) - val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES; - else - val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS; - - dsi_write(dsi, DSI_VID_MODE_CFG, val); -} - -static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi, - enum dw_mipi_dsi_mode mode) -{ - if (mode == DW_MIPI_DSI_CMD_MODE) { - dsi_write(dsi, DSI_PWR_UP, RESET); - dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE); - dsi_write(dsi, DSI_PWR_UP, POWERUP); - } else { - dsi_write(dsi, DSI_PWR_UP, RESET); - dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE); - dw_mipi_dsi_video_mode_config(dsi); - dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS); - dsi_write(dsi, DSI_PWR_UP, POWERUP); - } -} - -static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi) -{ - dsi_write(dsi, DSI_PWR_UP, RESET); - dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ); -} - -static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi) -{ - /* - * The maximum permitted escape clock is 20MHz and it is derived from - * lanebyteclk, which is running at "lane_mbps / 8". Thus we want: - * - * (lane_mbps >> 3) / esc_clk_division < 20 - * which is: - * (lane_mbps >> 3) / 20 > esc_clk_division - */ - u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1; - - dsi_write(dsi, DSI_PWR_UP, RESET); - dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK - | PHY_RSTZ | PHY_SHUTDOWNZ); - dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) | - TX_ESC_CLK_DIVIDSION(esc_clk_division)); -} - -static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode) -{ - u32 val = 0, color = 0; - - switch (dsi->format) { - case MIPI_DSI_FMT_RGB888: - color = DPI_COLOR_CODING_24BIT; - break; - case MIPI_DSI_FMT_RGB666: - color = DPI_COLOR_CODING_18BIT_2 | EN18_LOOSELY; - break; - case MIPI_DSI_FMT_RGB666_PACKED: - color = DPI_COLOR_CODING_18BIT_1; - break; - case MIPI_DSI_FMT_RGB565: - color = DPI_COLOR_CODING_16BIT_1; - break; - } - - if (mode->flags & DRM_MODE_FLAG_NVSYNC) - val |= VSYNC_ACTIVE_LOW; - if (mode->flags & DRM_MODE_FLAG_NHSYNC) - val |= HSYNC_ACTIVE_LOW; - - dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel)); - dsi_write(dsi, DSI_DPI_COLOR_CODING, color); - dsi_write(dsi, DSI_DPI_CFG_POL, val); - dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(4) - | INVACT_LPCMD_TIME(4)); -} - -static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi) -{ - dsi_write(dsi, DSI_PCKHDL_CFG, EN_CRC_RX | EN_ECC_RX | EN_BTA); -} - -static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode) -{ - dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay)); -} - -static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi) -{ - dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000)); - dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00); - dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE); -} - -/* Get lane byte clock cycles. */ -static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode, - u32 hcomponent) -{ - u32 frac, lbcc; - - lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8; - - frac = lbcc % mode->clock; - lbcc = lbcc / mode->clock; - if (frac) - lbcc++; - - return lbcc; -} - -static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode) -{ - u32 htotal, hsa, hbp, lbcc; - - htotal = mode->htotal; - hsa = mode->hsync_end - mode->hsync_start; - hbp = mode->htotal - mode->hsync_end; - - lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal); - dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc); - - lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa); - dsi_write(dsi, DSI_VID_HSA_TIME, lbcc); - - lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp); - dsi_write(dsi, DSI_VID_HBP_TIME, lbcc); -} - -static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode) -{ - u32 vactive, vsa, vfp, vbp; - - vactive = mode->vdisplay; - vsa = mode->vsync_end - mode->vsync_start; - vfp = mode->vsync_start - mode->vdisplay; - vbp = mode->vtotal - mode->vsync_end; - - dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive); - dsi_write(dsi, DSI_VID_VSA_LINES, vsa); - dsi_write(dsi, DSI_VID_VFP_LINES, vfp); - dsi_write(dsi, DSI_VID_VBP_LINES, vbp); -} - -static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi) -{ - dsi_write(dsi, DSI_PHY_TMR_CFG, PHY_HS2LP_TIME(0x40) - | PHY_LP2HS_TIME(0x40) | MAX_RD_TIME(10000)); - - dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG, PHY_CLKHS2LP_TIME(0x40) - | PHY_CLKLP2HS_TIME(0x40)); -} - -static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi) -{ - dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) | - N_LANES(dsi->lanes)); -} - -static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi) -{ - dsi_read(dsi, DSI_INT_ST0); - dsi_read(dsi, DSI_INT_ST1); - dsi_write(dsi, DSI_INT_MSK0, 0); - dsi_write(dsi, DSI_INT_MSK1, 0); -} - -static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) -{ - struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder); - - if (dsi->dpms_mode != DRM_MODE_DPMS_ON) - return; - - if (clk_prepare_enable(dsi->pclk)) { - DRM_DEV_ERROR(dsi->dev, "Failed to enable pclk\n"); - return; - } - - drm_panel_disable(dsi->panel); - - dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE); - drm_panel_unprepare(dsi->panel); - - dw_mipi_dsi_disable(dsi); - pm_runtime_put(dsi->dev); - clk_disable_unprepare(dsi->pclk); - dsi->dpms_mode = DRM_MODE_DPMS_OFF; -} - -static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) -{ - struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder); - struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode; - const struct dw_mipi_dsi_plat_data *pdata = dsi->pdata; - int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder); - u32 val; - int ret; - - ret = dw_mipi_dsi_get_lane_bps(dsi, mode); - if (ret < 0) - return; - - if (dsi->dpms_mode == DRM_MODE_DPMS_ON) - return; - - if (clk_prepare_enable(dsi->pclk)) { - DRM_DEV_ERROR(dsi->dev, "Failed to enable pclk\n"); - return; - } - - pm_runtime_get_sync(dsi->dev); - dw_mipi_dsi_init(dsi); - dw_mipi_dsi_dpi_config(dsi, mode); - dw_mipi_dsi_packet_handler_config(dsi); - dw_mipi_dsi_video_mode_config(dsi); - dw_mipi_dsi_video_packet_config(dsi, mode); - dw_mipi_dsi_command_mode_config(dsi); - dw_mipi_dsi_line_timer_config(dsi, mode); - dw_mipi_dsi_vertical_timing_config(dsi, mode); - dw_mipi_dsi_dphy_timing_config(dsi); - dw_mipi_dsi_dphy_interface_config(dsi); - dw_mipi_dsi_clear_err(dsi); - - /* - * For the RK3399, the clk of grf must be enabled before writing grf - * register. And for RK3288 or other soc, this grf_clk must be NULL, - * the clk_prepare_enable return true directly. - */ - ret = clk_prepare_enable(dsi->grf_clk); - if (ret) { - DRM_DEV_ERROR(dsi->dev, "Failed to enable grf_clk: %d\n", ret); - return; - } - - if (pdata->grf_dsi0_mode_reg) - regmap_write(dsi->grf_regmap, pdata->grf_dsi0_mode_reg, - pdata->grf_dsi0_mode); - - dw_mipi_dsi_phy_init(dsi); - dw_mipi_dsi_wait_for_two_frames(mode); - - dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE); - if (drm_panel_prepare(dsi->panel)) - DRM_DEV_ERROR(dsi->dev, "failed to prepare panel\n"); - - dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE); - drm_panel_enable(dsi->panel); - - clk_disable_unprepare(dsi->pclk); - - if (mux) - val = pdata->dsi0_en_bit | (pdata->dsi0_en_bit << 16); - else - val = pdata->dsi0_en_bit << 16; - - regmap_write(dsi->grf_regmap, pdata->grf_switch_reg, val); - DRM_DEV_DEBUG(dsi->dev, - "vop %s output to dsi0\n", (mux) ? "LIT" : "BIG"); - dsi->dpms_mode = DRM_MODE_DPMS_ON; - - clk_disable_unprepare(dsi->grf_clk); -} - -static int -dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder, - struct drm_crtc_state *crtc_state, - struct drm_connector_state *conn_state) -{ - struct rockchip_crtc_state *s = to_rockchip_crtc_state(crtc_state); - struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder); - - switch (dsi->format) { - case MIPI_DSI_FMT_RGB888: - s->output_mode = ROCKCHIP_OUT_MODE_P888; - break; - case MIPI_DSI_FMT_RGB666: - s->output_mode = ROCKCHIP_OUT_MODE_P666; - break; - case MIPI_DSI_FMT_RGB565: - s->output_mode = ROCKCHIP_OUT_MODE_P565; - break; - default: - WARN_ON(1); - return -EINVAL; - } - - s->output_type = DRM_MODE_CONNECTOR_DSI; - - return 0; -} - -static const struct drm_encoder_helper_funcs -dw_mipi_dsi_encoder_helper_funcs = { - .enable = dw_mipi_dsi_encoder_enable, - .disable = dw_mipi_dsi_encoder_disable, - .atomic_check = dw_mipi_dsi_encoder_atomic_check, -}; - -static const struct drm_encoder_funcs dw_mipi_dsi_encoder_funcs = { - .destroy = drm_encoder_cleanup, -}; - -static int dw_mipi_dsi_connector_get_modes(struct drm_connector *connector) -{ - struct dw_mipi_dsi *dsi = con_to_dsi(connector); - - return drm_panel_get_modes(dsi->panel); -} - -static struct drm_connector_helper_funcs dw_mipi_dsi_connector_helper_funcs = { - .get_modes = dw_mipi_dsi_connector_get_modes, -}; - -static void dw_mipi_dsi_drm_connector_destroy(struct drm_connector *connector) -{ - drm_connector_unregister(connector); - drm_connector_cleanup(connector); -} - -static const struct drm_connector_funcs dw_mipi_dsi_atomic_connector_funcs = { - .fill_modes = drm_helper_probe_single_connector_modes, - .destroy = dw_mipi_dsi_drm_connector_destroy, - .reset = drm_atomic_helper_connector_reset, - .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, - .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, -}; - -static int dw_mipi_dsi_register(struct drm_device *drm, - struct dw_mipi_dsi *dsi) -{ - struct drm_encoder *encoder = &dsi->encoder; - struct drm_connector *connector = &dsi->connector; - struct device *dev = dsi->dev; - int ret; - - encoder->possible_crtcs = drm_of_find_possible_crtcs(drm, - dev->of_node); - /* - * If we failed to find the CRTC(s) which this encoder is - * supposed to be connected to, it's because the CRTC has - * not been registered yet. Defer probing, and hope that - * the required CRTC is added later. - */ - if (encoder->possible_crtcs == 0) - return -EPROBE_DEFER; - - drm_encoder_helper_add(&dsi->encoder, - &dw_mipi_dsi_encoder_helper_funcs); - ret = drm_encoder_init(drm, &dsi->encoder, &dw_mipi_dsi_encoder_funcs, - DRM_MODE_ENCODER_DSI, NULL); - if (ret) { - DRM_DEV_ERROR(dev, "Failed to initialize encoder with drm\n"); - return ret; - } - - drm_connector_helper_add(connector, - &dw_mipi_dsi_connector_helper_funcs); - - drm_connector_init(drm, &dsi->connector, - &dw_mipi_dsi_atomic_connector_funcs, - DRM_MODE_CONNECTOR_DSI); - - drm_connector_attach_encoder(connector, encoder); - - return 0; -} - -static int rockchip_mipi_parse_dt(struct dw_mipi_dsi *dsi) -{ - struct device_node *np = dsi->dev->of_node; - - dsi->grf_regmap = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); - if (IS_ERR(dsi->grf_regmap)) { - DRM_DEV_ERROR(dsi->dev, "Unable to get rockchip,grf\n"); - return PTR_ERR(dsi->grf_regmap); - } - - return 0; -} - -static struct dw_mipi_dsi_plat_data rk3288_mipi_dsi_drv_data = { - .dsi0_en_bit = RK3288_DSI0_SEL_VOP_LIT, - .dsi1_en_bit = RK3288_DSI1_SEL_VOP_LIT, - .grf_switch_reg = RK3288_GRF_SOC_CON6, - .max_data_lanes = 4, -}; - -static struct dw_mipi_dsi_plat_data rk3399_mipi_dsi_drv_data = { - .dsi0_en_bit = RK3399_DSI0_SEL_VOP_LIT, - .dsi1_en_bit = RK3399_DSI1_SEL_VOP_LIT, - .grf_switch_reg = RK3399_GRF_SOC_CON20, - .grf_dsi0_mode = RK3399_GRF_DSI_MODE, - .grf_dsi0_mode_reg = RK3399_GRF_SOC_CON22, - .flags = DW_MIPI_NEEDS_PHY_CFG_CLK | DW_MIPI_NEEDS_GRF_CLK, - .max_data_lanes = 4, -}; - -static const struct of_device_id dw_mipi_dsi_dt_ids[] = { - { - .compatible = "rockchip,rk3288-mipi-dsi", - .data = &rk3288_mipi_dsi_drv_data, - }, { - .compatible = "rockchip,rk3399-mipi-dsi", - .data = &rk3399_mipi_dsi_drv_data, - }, - { /* sentinel */ } -}; -MODULE_DEVICE_TABLE(of, dw_mipi_dsi_dt_ids); - -static int dw_mipi_dsi_bind(struct device *dev, struct device *master, - void *data) -{ - const struct of_device_id *of_id = - of_match_device(dw_mipi_dsi_dt_ids, dev); - const struct dw_mipi_dsi_plat_data *pdata = of_id->data; - struct platform_device *pdev = to_platform_device(dev); - struct reset_control *apb_rst; - struct drm_device *drm = data; - struct dw_mipi_dsi *dsi; - struct resource *res; - int ret; - - dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL); - if (!dsi) - return -ENOMEM; - - dsi->dev = dev; - dsi->pdata = pdata; - dsi->dpms_mode = DRM_MODE_DPMS_OFF; - - ret = rockchip_mipi_parse_dt(dsi); - if (ret) - return ret; - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - dsi->base = devm_ioremap_resource(dev, res); - if (IS_ERR(dsi->base)) - return PTR_ERR(dsi->base); - - dsi->pllref_clk = devm_clk_get(dev, "ref"); - if (IS_ERR(dsi->pllref_clk)) { - ret = PTR_ERR(dsi->pllref_clk); - DRM_DEV_ERROR(dev, - "Unable to get pll reference clock: %d\n", ret); - return ret; - } - - dsi->pclk = devm_clk_get(dev, "pclk"); - if (IS_ERR(dsi->pclk)) { - ret = PTR_ERR(dsi->pclk); - DRM_DEV_ERROR(dev, "Unable to get pclk: %d\n", ret); - return ret; - } - - /* - * Note that the reset was not defined in the initial device tree, so - * we have to be prepared for it not being found. - */ - apb_rst = devm_reset_control_get(dev, "apb"); - if (IS_ERR(apb_rst)) { - ret = PTR_ERR(apb_rst); - if (ret == -ENOENT) { - apb_rst = NULL; - } else { - DRM_DEV_ERROR(dev, - "Unable to get reset control: %d\n", ret); - return ret; - } - } - - if (apb_rst) { - ret = clk_prepare_enable(dsi->pclk); - if (ret) { - DRM_DEV_ERROR(dev, "Failed to enable pclk\n"); - return ret; - } - - reset_control_assert(apb_rst); - usleep_range(10, 20); - reset_control_deassert(apb_rst); - - clk_disable_unprepare(dsi->pclk); - } - - if (pdata->flags & DW_MIPI_NEEDS_PHY_CFG_CLK) { - dsi->phy_cfg_clk = devm_clk_get(dev, "phy_cfg"); - if (IS_ERR(dsi->phy_cfg_clk)) { - ret = PTR_ERR(dsi->phy_cfg_clk); - DRM_DEV_ERROR(dev, - "Unable to get phy_cfg_clk: %d\n", ret); - return ret; - } - } - - if (pdata->flags & DW_MIPI_NEEDS_GRF_CLK) { - dsi->grf_clk = devm_clk_get(dev, "grf"); - if (IS_ERR(dsi->grf_clk)) { - ret = PTR_ERR(dsi->grf_clk); - DRM_DEV_ERROR(dev, "Unable to get grf_clk: %d\n", ret); - return ret; - } - } - - ret = clk_prepare_enable(dsi->pllref_clk); - if (ret) { - DRM_DEV_ERROR(dev, "Failed to enable pllref_clk\n"); - return ret; - } - - ret = dw_mipi_dsi_register(drm, dsi); - if (ret) { - DRM_DEV_ERROR(dev, "Failed to register mipi_dsi: %d\n", ret); - goto err_pllref; - } - - dsi->dsi_host.ops = &dw_mipi_dsi_host_ops; - dsi->dsi_host.dev = dev; - ret = mipi_dsi_host_register(&dsi->dsi_host); - if (ret) { - DRM_DEV_ERROR(dev, "Failed to register MIPI host: %d\n", ret); - goto err_cleanup; - } - - if (!dsi->panel) { - ret = -EPROBE_DEFER; - goto err_mipi_dsi_host; - } - - dev_set_drvdata(dev, dsi); - pm_runtime_enable(dev); - return 0; - -err_mipi_dsi_host: - mipi_dsi_host_unregister(&dsi->dsi_host); -err_cleanup: - dsi->connector.funcs->destroy(&dsi->connector); - dsi->encoder.funcs->destroy(&dsi->encoder); -err_pllref: - clk_disable_unprepare(dsi->pllref_clk); - return ret; -} - -static void dw_mipi_dsi_unbind(struct device *dev, struct device *master, - void *data) -{ - struct dw_mipi_dsi *dsi = dev_get_drvdata(dev); - - mipi_dsi_host_unregister(&dsi->dsi_host); - pm_runtime_disable(dev); - - dsi->connector.funcs->destroy(&dsi->connector); - dsi->encoder.funcs->destroy(&dsi->encoder); - - clk_disable_unprepare(dsi->pllref_clk); -} - -static const struct component_ops dw_mipi_dsi_ops = { - .bind = dw_mipi_dsi_bind, - .unbind = dw_mipi_dsi_unbind, -}; - -static int dw_mipi_dsi_probe(struct platform_device *pdev) -{ - return component_add(&pdev->dev, &dw_mipi_dsi_ops); -} - -static int dw_mipi_dsi_remove(struct platform_device *pdev) -{ - component_del(&pdev->dev, &dw_mipi_dsi_ops); - return 0; -} - -struct platform_driver dw_mipi_dsi_driver = { - .probe = dw_mipi_dsi_probe, - .remove = dw_mipi_dsi_remove, - .driver = { - .of_match_table = dw_mipi_dsi_dt_ids, - .name = DRIVER_NAME, - }, -}; diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.c b/drivers/gpu/drm/rockchip/rockchip_drm_drv.c index 941f35233b1f..37f9a3b651ab 100644 --- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.c +++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.c @@ -489,7 +489,7 @@ static int __init rockchip_drm_init(void) ADD_ROCKCHIP_SUB_DRIVER(cdn_dp_driver, CONFIG_ROCKCHIP_CDN_DP); ADD_ROCKCHIP_SUB_DRIVER(dw_hdmi_rockchip_pltfm_driver, CONFIG_ROCKCHIP_DW_HDMI); - ADD_ROCKCHIP_SUB_DRIVER(dw_mipi_dsi_driver, + ADD_ROCKCHIP_SUB_DRIVER(dw_mipi_dsi_rockchip_driver, CONFIG_ROCKCHIP_DW_MIPI_DSI); ADD_ROCKCHIP_SUB_DRIVER(inno_hdmi_driver, CONFIG_ROCKCHIP_INNO_HDMI); diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h index 21a023a97bb8..453fef6a55b9 100644 --- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h +++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h @@ -67,7 +67,7 @@ int rockchip_drm_wait_vact_end(struct drm_crtc *crtc, unsigned int mstimeout); int rockchip_drm_endpoint_is_subdriver(struct device_node *ep); extern struct platform_driver cdn_dp_driver; extern struct platform_driver dw_hdmi_rockchip_pltfm_driver; -extern struct platform_driver dw_mipi_dsi_driver; +extern struct platform_driver dw_mipi_dsi_rockchip_driver; extern struct platform_driver inno_hdmi_driver; extern struct platform_driver rockchip_dp_driver; extern struct platform_driver rockchip_lvds_driver; -- 2.18.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 5/7] drm/rockchip: dsi: migrate to use dw-mipi-dsi bridge driver @ 2018-10-01 12:38 ` Heiko Stuebner 0 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: linux-arm-kernel From: Nickey Yang <nickey.yang@rock-chips.com> Add the ROCKCHIP DSI controller driver that uses the Synopsys DesignWare MIPI DSI host controller bridge and remove the old separate one. changes: v2: add err_pllref, remove unnecessary encoder.enable & disable correct spelling mistakes v3: call dw_mipi_dsi_unbind() in dw_mipi_dsi_rockchip_unbind() fix typo, use of_device_get_match_data(), change some bind() logic into probe() add 'dev_set_drvdata()' v4: return -EINVAL when can not get best_freq add a clarifying comment when get vco add review tag v5: keep our power domain enabled while touching GRF v6: change func name dw_mipi_encoder_disable to dw_mipi_dsi_encoder_disable v7: none v8: Heiko add Archit's Review tag adapt to recent changes in the original rockchip-dsi driver beautify grf-handling split hw-setup (resources, dsi-host) from bind into probe v2-new: Heiko add SPDX header instead of license blurb drop old versioning to not confuse people v3-new: Heiko include ordering moved hwaccess from mode_set to enable callback move pllref_clk enablement to bind (needed by bridge mode_set->lane_mbps) v4-new: Heiko rebase against recent rockchip-dsi changes move to call component_add in the new glue host-attach Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Archit Taneja <architt@codeaurora.org> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- drivers/gpu/drm/rockchip/Kconfig | 2 +- drivers/gpu/drm/rockchip/Makefile | 2 +- .../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 939 ++++++++++++ drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 1349 ----------------- drivers/gpu/drm/rockchip/rockchip_drm_drv.c | 2 +- drivers/gpu/drm/rockchip/rockchip_drm_drv.h | 2 +- 6 files changed, 943 insertions(+), 1353 deletions(-) create mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c delete mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi.c diff --git a/drivers/gpu/drm/rockchip/Kconfig b/drivers/gpu/drm/rockchip/Kconfig index 26438d45732b..1e75196f9659 100644 --- a/drivers/gpu/drm/rockchip/Kconfig +++ b/drivers/gpu/drm/rockchip/Kconfig @@ -7,7 +7,7 @@ config DRM_ROCKCHIP select VIDEOMODE_HELPERS select DRM_ANALOGIX_DP if ROCKCHIP_ANALOGIX_DP select DRM_DW_HDMI if ROCKCHIP_DW_HDMI - select DRM_MIPI_DSI if ROCKCHIP_DW_MIPI_DSI + select DRM_DW_MIPI_DSI if ROCKCHIP_DW_MIPI_DSI select DRM_RGB if ROCKCHIP_RGB select SND_SOC_HDMI_CODEC if ROCKCHIP_CDN_DP && SND_SOC help diff --git a/drivers/gpu/drm/rockchip/Makefile b/drivers/gpu/drm/rockchip/Makefile index 868263ff0302..f6fc9d5dd0ad 100644 --- a/drivers/gpu/drm/rockchip/Makefile +++ b/drivers/gpu/drm/rockchip/Makefile @@ -11,7 +11,7 @@ rockchipdrm-$(CONFIG_DRM_FBDEV_EMULATION) += rockchip_drm_fbdev.o rockchipdrm-$(CONFIG_ROCKCHIP_ANALOGIX_DP) += analogix_dp-rockchip.o rockchipdrm-$(CONFIG_ROCKCHIP_CDN_DP) += cdn-dp-core.o cdn-dp-reg.o rockchipdrm-$(CONFIG_ROCKCHIP_DW_HDMI) += dw_hdmi-rockchip.o -rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi.o +rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi-rockchip.o rockchipdrm-$(CONFIG_ROCKCHIP_INNO_HDMI) += inno_hdmi.o rockchipdrm-$(CONFIG_ROCKCHIP_LVDS) += rockchip_lvds.o rockchipdrm-$(CONFIG_ROCKCHIP_RGB) += rockchip_rgb.o diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c new file mode 100644 index 000000000000..b3aae8439aa3 --- /dev/null +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c @@ -0,0 +1,939 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd + * Author: + * Chris Zhong <zyw@rock-chips.com> + * Nickey Yang <nickey.yang@rock-chips.com> + */ + +#include <drm/drmP.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/bridge/dw_mipi_dsi.h> +#include <drm/drm_of.h> +#include <linux/clk.h> +#include <linux/iopoll.h> +#include <linux/math64.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/pm_runtime.h> +#include <linux/regmap.h> +#include <video/mipi_display.h> + +#include "rockchip_drm_drv.h" +#include "rockchip_drm_vop.h" + +#define DSI_PHY_RSTZ 0xa0 +#define PHY_DISFORCEPLL 0 +#define PHY_ENFORCEPLL BIT(3) +#define PHY_DISABLECLK 0 +#define PHY_ENABLECLK BIT(2) +#define PHY_RSTZ 0 +#define PHY_UNRSTZ BIT(1) +#define PHY_SHUTDOWNZ 0 +#define PHY_UNSHUTDOWNZ BIT(0) + +#define DSI_PHY_IF_CFG 0xa4 +#define N_LANES(n) ((((n) - 1) & 0x3) << 0) +#define PHY_STOP_WAIT_TIME(cycle) (((cycle) & 0xff) << 8) + +#define DSI_PHY_STATUS 0xb0 +#define LOCK BIT(0) +#define STOP_STATE_CLK_LANE BIT(2) + +#define DSI_PHY_TST_CTRL0 0xb4 +#define PHY_TESTCLK BIT(1) +#define PHY_UNTESTCLK 0 +#define PHY_TESTCLR BIT(0) +#define PHY_UNTESTCLR 0 + +#define DSI_PHY_TST_CTRL1 0xb8 +#define PHY_TESTEN BIT(16) +#define PHY_UNTESTEN 0 +#define PHY_TESTDOUT(n) (((n) & 0xff) << 8) +#define PHY_TESTDIN(n) (((n) & 0xff) << 0) + +#define DSI_INT_ST0 0xbc +#define DSI_INT_ST1 0xc0 +#define DSI_INT_MSK0 0xc4 +#define DSI_INT_MSK1 0xc8 + +#define PHY_STATUS_TIMEOUT_US 10000 +#define CMD_PKT_STATUS_TIMEOUT_US 20000 + +#define BYPASS_VCO_RANGE BIT(7) +#define VCO_RANGE_CON_SEL(val) (((val) & 0x7) << 3) +#define VCO_IN_CAP_CON_DEFAULT (0x0 << 1) +#define VCO_IN_CAP_CON_LOW (0x1 << 1) +#define VCO_IN_CAP_CON_HIGH (0x2 << 1) +#define REF_BIAS_CUR_SEL BIT(0) + +#define CP_CURRENT_3UA 0x1 +#define CP_CURRENT_4_5UA 0x2 +#define CP_CURRENT_7_5UA 0x6 +#define CP_CURRENT_6UA 0x9 +#define CP_CURRENT_12UA 0xb +#define CP_CURRENT_SEL(val) ((val) & 0xf) +#define CP_PROGRAM_EN BIT(7) + +#define LPF_RESISTORS_15_5KOHM 0x1 +#define LPF_RESISTORS_13KOHM 0x2 +#define LPF_RESISTORS_11_5KOHM 0x4 +#define LPF_RESISTORS_10_5KOHM 0x8 +#define LPF_RESISTORS_8KOHM 0x10 +#define LPF_PROGRAM_EN BIT(6) +#define LPF_RESISTORS_SEL(val) ((val) & 0x3f) + +#define HSFREQRANGE_SEL(val) (((val) & 0x3f) << 1) + +#define INPUT_DIVIDER(val) (((val) - 1) & 0x7f) +#define LOW_PROGRAM_EN 0 +#define HIGH_PROGRAM_EN BIT(7) +#define LOOP_DIV_LOW_SEL(val) (((val) - 1) & 0x1f) +#define LOOP_DIV_HIGH_SEL(val) ((((val) - 1) >> 5) & 0xf) +#define PLL_LOOP_DIV_EN BIT(5) +#define PLL_INPUT_DIV_EN BIT(4) + +#define POWER_CONTROL BIT(6) +#define INTERNAL_REG_CURRENT BIT(3) +#define BIAS_BLOCK_ON BIT(2) +#define BANDGAP_ON BIT(0) + +#define TER_RESISTOR_HIGH BIT(7) +#define TER_RESISTOR_LOW 0 +#define LEVEL_SHIFTERS_ON BIT(6) +#define TER_CAL_DONE BIT(5) +#define SETRD_MAX (0x7 << 2) +#define POWER_MANAGE BIT(1) +#define TER_RESISTORS_ON BIT(0) + +#define BIASEXTR_SEL(val) ((val) & 0x7) +#define BANDGAP_SEL(val) ((val) & 0x7) +#define TLP_PROGRAM_EN BIT(7) +#define THS_PRE_PROGRAM_EN BIT(7) +#define THS_ZERO_PROGRAM_EN BIT(6) + +#define PLL_BIAS_CUR_SEL_CAP_VCO_CONTROL 0x10 +#define PLL_CP_CONTROL_PLL_LOCK_BYPASS 0x11 +#define PLL_LPF_AND_CP_CONTROL 0x12 +#define PLL_INPUT_DIVIDER_RATIO 0x17 +#define PLL_LOOP_DIVIDER_RATIO 0x18 +#define PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL 0x19 +#define BANDGAP_AND_BIAS_CONTROL 0x20 +#define TERMINATION_RESISTER_CONTROL 0x21 +#define AFE_BIAS_BANDGAP_ANALOG_PROGRAMMABILITY 0x22 +#define HS_RX_CONTROL_OF_LANE_0 0x44 +#define HS_TX_CLOCK_LANE_REQUEST_STATE_TIME_CONTROL 0x60 +#define HS_TX_CLOCK_LANE_PREPARE_STATE_TIME_CONTROL 0x61 +#define HS_TX_CLOCK_LANE_HS_ZERO_STATE_TIME_CONTROL 0x62 +#define HS_TX_CLOCK_LANE_TRAIL_STATE_TIME_CONTROL 0x63 +#define HS_TX_CLOCK_LANE_EXIT_STATE_TIME_CONTROL 0x64 +#define HS_TX_CLOCK_LANE_POST_TIME_CONTROL 0x65 +#define HS_TX_DATA_LANE_REQUEST_STATE_TIME_CONTROL 0x70 +#define HS_TX_DATA_LANE_PREPARE_STATE_TIME_CONTROL 0x71 +#define HS_TX_DATA_LANE_HS_ZERO_STATE_TIME_CONTROL 0x72 +#define HS_TX_DATA_LANE_TRAIL_STATE_TIME_CONTROL 0x73 +#define HS_TX_DATA_LANE_EXIT_STATE_TIME_CONTROL 0x74 + +#define DW_MIPI_NEEDS_PHY_CFG_CLK BIT(0) +#define DW_MIPI_NEEDS_GRF_CLK BIT(1) + +#define RK3288_GRF_SOC_CON6 0x025c +#define RK3288_DSI0_LCDC_SEL BIT(6) +#define RK3288_DSI1_LCDC_SEL BIT(9) + +#define RK3399_GRF_SOC_CON20 0x6250 +#define RK3399_DSI0_LCDC_SEL BIT(0) +#define RK3399_DSI1_LCDC_SEL BIT(4) + +#define RK3399_GRF_SOC_CON22 0x6258 +#define RK3399_DSI0_TURNREQUEST (0xf << 12) +#define RK3399_DSI0_TURNDISABLE (0xf << 8) +#define RK3399_DSI0_FORCETXSTOPMODE (0xf << 4) +#define RK3399_DSI0_FORCERXMODE (0xf << 0) + +#define RK3399_GRF_SOC_CON23 0x625c +#define RK3399_DSI1_TURNDISABLE (0xf << 12) +#define RK3399_DSI1_FORCETXSTOPMODE (0xf << 8) +#define RK3399_DSI1_FORCERXMODE (0xf << 4) +#define RK3399_DSI1_ENABLE (0xf << 0) + +#define RK3399_GRF_SOC_CON24 0x6260 +#define RK3399_TXRX_MASTERSLAVEZ BIT(7) +#define RK3399_TXRX_ENABLECLK BIT(6) +#define RK3399_TXRX_BASEDIR BIT(5) + +#define HIWORD_UPDATE(val, mask) (val | (mask) << 16) + +#define to_dsi(nm) container_of(nm, struct dw_mipi_dsi_rockchip, nm) + +enum { + BANDGAP_97_07, + BANDGAP_98_05, + BANDGAP_99_02, + BANDGAP_100_00, + BANDGAP_93_17, + BANDGAP_94_15, + BANDGAP_95_12, + BANDGAP_96_10, +}; + +enum { + BIASEXTR_87_1, + BIASEXTR_91_5, + BIASEXTR_95_9, + BIASEXTR_100, + BIASEXTR_105_94, + BIASEXTR_111_88, + BIASEXTR_118_8, + BIASEXTR_127_7, +}; + +struct rockchip_dw_dsi_chip_data { + u32 reg; + + u32 lcdsel_grf_reg; + u32 lcdsel_big; + u32 lcdsel_lit; + + u32 enable_grf_reg; + u32 enable; + + u32 lanecfg1_grf_reg; + u32 lanecfg1; + u32 lanecfg2_grf_reg; + u32 lanecfg2; + + unsigned int flags; + unsigned int max_data_lanes; +}; + +struct dw_mipi_dsi_rockchip { + struct device *dev; + struct drm_encoder encoder; + void __iomem *base; + + struct regmap *grf_regmap; + struct clk *pllref_clk; + struct clk *grf_clk; + struct clk *phy_cfg_clk; + + unsigned int lane_mbps; /* per lane */ + u16 input_div; + u16 feedback_div; + u32 format; + + struct dw_mipi_dsi *dmd; + const struct rockchip_dw_dsi_chip_data *cdata; + struct dw_mipi_dsi_plat_data pdata; +}; + +struct dphy_pll_parameter_map { + unsigned int max_mbps; + u8 hsfreqrange; + u8 icpctrl; + u8 lpfctrl; +}; + +/* The table is based on 27MHz DPHY pll reference clock. */ +static const struct dphy_pll_parameter_map dppa_map[] = { + { 89, 0x00, CP_CURRENT_3UA, LPF_RESISTORS_13KOHM }, + { 99, 0x10, CP_CURRENT_3UA, LPF_RESISTORS_13KOHM }, + { 109, 0x20, CP_CURRENT_3UA, LPF_RESISTORS_13KOHM }, + { 129, 0x01, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 139, 0x11, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 149, 0x21, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 169, 0x02, CP_CURRENT_6UA, LPF_RESISTORS_13KOHM }, + { 179, 0x12, CP_CURRENT_6UA, LPF_RESISTORS_13KOHM }, + { 199, 0x22, CP_CURRENT_6UA, LPF_RESISTORS_13KOHM }, + { 219, 0x03, CP_CURRENT_4_5UA, LPF_RESISTORS_13KOHM }, + { 239, 0x13, CP_CURRENT_4_5UA, LPF_RESISTORS_13KOHM }, + { 249, 0x23, CP_CURRENT_4_5UA, LPF_RESISTORS_13KOHM }, + { 269, 0x04, CP_CURRENT_6UA, LPF_RESISTORS_11_5KOHM }, + { 299, 0x14, CP_CURRENT_6UA, LPF_RESISTORS_11_5KOHM }, + { 329, 0x05, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 359, 0x15, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 399, 0x25, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM }, + { 449, 0x06, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 499, 0x16, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 549, 0x07, CP_CURRENT_7_5UA, LPF_RESISTORS_10_5KOHM }, + { 599, 0x17, CP_CURRENT_7_5UA, LPF_RESISTORS_10_5KOHM }, + { 649, 0x08, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 699, 0x18, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 749, 0x09, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 799, 0x19, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 849, 0x29, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 899, 0x39, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM }, + { 949, 0x0a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM }, + { 999, 0x1a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM }, + {1049, 0x2a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM }, + {1099, 0x3a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM }, + {1149, 0x0b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1199, 0x1b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1249, 0x2b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1299, 0x3b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1349, 0x0c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1399, 0x1c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1449, 0x2c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM }, + {1500, 0x3c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM } +}; + +static int max_mbps_to_parameter(unsigned int max_mbps) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(dppa_map); i++) + if (dppa_map[i].max_mbps >= max_mbps) + return i; + + return -EINVAL; +} + +static inline void dsi_write(struct dw_mipi_dsi_rockchip *dsi, u32 reg, u32 val) +{ + writel(val, dsi->base + reg); +} + +static inline u32 dsi_read(struct dw_mipi_dsi_rockchip *dsi, u32 reg) +{ + return readl(dsi->base + reg); +} + +static inline void dsi_set(struct dw_mipi_dsi_rockchip *dsi, u32 reg, u32 mask) +{ + dsi_write(dsi, reg, dsi_read(dsi, reg) | mask); +} + +static inline void dsi_update_bits(struct dw_mipi_dsi_rockchip *dsi, u32 reg, + u32 mask, u32 val) +{ + dsi_write(dsi, reg, (dsi_read(dsi, reg) & ~mask) | val); +} + +static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi_rockchip *dsi, + u8 test_code, + u8 test_data) +{ + /* + * With the falling edge on TESTCLK, the TESTDIN[7:0] signal content + * is latched internally as the current test code. Test data is + * programmed internally by rising edge on TESTCLK. + */ + dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); + + dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_TESTEN | PHY_TESTDOUT(0) | + PHY_TESTDIN(test_code)); + + dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLK | PHY_UNTESTCLR); + + dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_UNTESTEN | PHY_TESTDOUT(0) | + PHY_TESTDIN(test_data)); + + dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); +} + +/** + * ns2bc - Nanoseconds to byte clock cycles + */ +static inline unsigned int ns2bc(struct dw_mipi_dsi_rockchip *dsi, int ns) +{ + return DIV_ROUND_UP(ns * dsi->lane_mbps / 8, 1000); +} + +/** + * ns2ui - Nanoseconds to UI time periods + */ +static inline unsigned int ns2ui(struct dw_mipi_dsi_rockchip *dsi, int ns) +{ + return DIV_ROUND_UP(ns * dsi->lane_mbps, 1000); +} + +static int dw_mipi_dsi_phy_init(void *priv_data) +{ + struct dw_mipi_dsi_rockchip *dsi = priv_data; + int ret, i, vco; + + /* + * Get vco from frequency(lane_mbps) + * vco frequency table + * 000 - between 80 and 200 MHz + * 001 - between 200 and 300 MHz + * 010 - between 300 and 500 MHz + * 011 - between 500 and 700 MHz + * 100 - between 700 and 900 MHz + * 101 - between 900 and 1100 MHz + * 110 - between 1100 and 1300 MHz + * 111 - between 1300 and 1500 MHz + */ + vco = (dsi->lane_mbps < 200) ? 0 : (dsi->lane_mbps + 100) / 200; + + i = max_mbps_to_parameter(dsi->lane_mbps); + if (i < 0) { + DRM_DEV_ERROR(dsi->dev, + "failed to get parameter for %dmbps clock\n", + dsi->lane_mbps); + return i; + } + + ret = clk_prepare_enable(dsi->phy_cfg_clk); + if (ret) { + DRM_DEV_ERROR(dsi->dev, "Failed to enable phy_cfg_clk\n"); + return ret; + } + + dw_mipi_dsi_phy_write(dsi, PLL_BIAS_CUR_SEL_CAP_VCO_CONTROL, + BYPASS_VCO_RANGE | + VCO_RANGE_CON_SEL(vco) | + VCO_IN_CAP_CON_LOW | + REF_BIAS_CUR_SEL); + + dw_mipi_dsi_phy_write(dsi, PLL_CP_CONTROL_PLL_LOCK_BYPASS, + CP_CURRENT_SEL(dppa_map[i].icpctrl)); + dw_mipi_dsi_phy_write(dsi, PLL_LPF_AND_CP_CONTROL, + CP_PROGRAM_EN | LPF_PROGRAM_EN | + LPF_RESISTORS_SEL(dppa_map[i].lpfctrl)); + + dw_mipi_dsi_phy_write(dsi, HS_RX_CONTROL_OF_LANE_0, + HSFREQRANGE_SEL(dppa_map[i].hsfreqrange)); + + dw_mipi_dsi_phy_write(dsi, PLL_INPUT_DIVIDER_RATIO, + INPUT_DIVIDER(dsi->input_div)); + dw_mipi_dsi_phy_write(dsi, PLL_LOOP_DIVIDER_RATIO, + LOOP_DIV_LOW_SEL(dsi->feedback_div) | + LOW_PROGRAM_EN); + /* + * We need set PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL immediately + * to make the configured LSB effective according to IP simulation + * and lab test results. + * Only in this way can we get correct mipi phy pll frequency. + */ + dw_mipi_dsi_phy_write(dsi, PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL, + PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN); + dw_mipi_dsi_phy_write(dsi, PLL_LOOP_DIVIDER_RATIO, + LOOP_DIV_HIGH_SEL(dsi->feedback_div) | + HIGH_PROGRAM_EN); + dw_mipi_dsi_phy_write(dsi, PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL, + PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN); + + dw_mipi_dsi_phy_write(dsi, AFE_BIAS_BANDGAP_ANALOG_PROGRAMMABILITY, + LOW_PROGRAM_EN | BIASEXTR_SEL(BIASEXTR_127_7)); + dw_mipi_dsi_phy_write(dsi, AFE_BIAS_BANDGAP_ANALOG_PROGRAMMABILITY, + HIGH_PROGRAM_EN | BANDGAP_SEL(BANDGAP_96_10)); + + dw_mipi_dsi_phy_write(dsi, BANDGAP_AND_BIAS_CONTROL, + POWER_CONTROL | INTERNAL_REG_CURRENT | + BIAS_BLOCK_ON | BANDGAP_ON); + + dw_mipi_dsi_phy_write(dsi, TERMINATION_RESISTER_CONTROL, + TER_RESISTOR_LOW | TER_CAL_DONE | + SETRD_MAX | TER_RESISTORS_ON); + dw_mipi_dsi_phy_write(dsi, TERMINATION_RESISTER_CONTROL, + TER_RESISTOR_HIGH | LEVEL_SHIFTERS_ON | + SETRD_MAX | POWER_MANAGE | + TER_RESISTORS_ON); + + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_REQUEST_STATE_TIME_CONTROL, + TLP_PROGRAM_EN | ns2bc(dsi, 500)); + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_PREPARE_STATE_TIME_CONTROL, + THS_PRE_PROGRAM_EN | ns2ui(dsi, 40)); + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_HS_ZERO_STATE_TIME_CONTROL, + THS_ZERO_PROGRAM_EN | ns2bc(dsi, 300)); + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_TRAIL_STATE_TIME_CONTROL, + THS_PRE_PROGRAM_EN | ns2ui(dsi, 100)); + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_EXIT_STATE_TIME_CONTROL, + BIT(5) | ns2bc(dsi, 100)); + dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_POST_TIME_CONTROL, + BIT(5) | (ns2bc(dsi, 60) + 7)); + + dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_REQUEST_STATE_TIME_CONTROL, + TLP_PROGRAM_EN | ns2bc(dsi, 500)); + dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_PREPARE_STATE_TIME_CONTROL, + THS_PRE_PROGRAM_EN | (ns2ui(dsi, 50) + 20)); + dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_HS_ZERO_STATE_TIME_CONTROL, + THS_ZERO_PROGRAM_EN | (ns2bc(dsi, 140) + 2)); + dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_TRAIL_STATE_TIME_CONTROL, + THS_PRE_PROGRAM_EN | (ns2ui(dsi, 60) + 8)); + dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_EXIT_STATE_TIME_CONTROL, + BIT(5) | ns2bc(dsi, 100)); + + clk_disable_unprepare(dsi->phy_cfg_clk); + + return ret; +} + +static int +dw_mipi_dsi_get_lane_mbps(void *priv_data, struct drm_display_mode *mode, + unsigned long mode_flags, u32 lanes, u32 format, + unsigned int *lane_mbps) +{ + struct dw_mipi_dsi_rockchip *dsi = priv_data; + int bpp; + unsigned long mpclk, tmp; + unsigned int target_mbps = 1000; + unsigned int max_mbps = dppa_map[ARRAY_SIZE(dppa_map) - 1].max_mbps; + unsigned long best_freq = 0; + unsigned long fvco_min, fvco_max, fin, fout; + unsigned int min_prediv, max_prediv; + unsigned int _prediv, uninitialized_var(best_prediv); + unsigned long _fbdiv, uninitialized_var(best_fbdiv); + unsigned long min_delta = ULONG_MAX; + + dsi->format = format; + bpp = mipi_dsi_pixel_format_to_bpp(dsi->format); + if (bpp < 0) { + DRM_DEV_ERROR(dsi->dev, + "failed to get bpp for pixel format %d\n", + dsi->format); + return bpp; + } + + mpclk = DIV_ROUND_UP(mode->clock, MSEC_PER_SEC); + if (mpclk) { + /* take 1 / 0.8, since mbps must big than bandwidth of RGB */ + tmp = mpclk * (bpp / lanes) * 10 / 8; + if (tmp < max_mbps) + target_mbps = tmp; + else + DRM_DEV_ERROR(dsi->dev, + "DPHY clock frequency is out of range\n"); + } + + fin = clk_get_rate(dsi->pllref_clk); + fout = target_mbps * USEC_PER_SEC; + + /* constraint: 5Mhz <= Fref / N <= 40MHz */ + min_prediv = DIV_ROUND_UP(fin, 40 * USEC_PER_SEC); + max_prediv = fin / (5 * USEC_PER_SEC); + + /* constraint: 80MHz <= Fvco <= 1500Mhz */ + fvco_min = 80 * USEC_PER_SEC; + fvco_max = 1500 * USEC_PER_SEC; + + for (_prediv = min_prediv; _prediv <= max_prediv; _prediv++) { + u64 tmp; + u32 delta; + /* Fvco = Fref * M / N */ + tmp = (u64)fout * _prediv; + do_div(tmp, fin); + _fbdiv = tmp; + /* + * Due to the use of a "by 2 pre-scaler," the range of the + * feedback multiplication value M is limited to even division + * numbers, and m must be greater than 6, not bigger than 512. + */ + if (_fbdiv < 6 || _fbdiv > 512) + continue; + + _fbdiv += _fbdiv % 2; + + tmp = (u64)_fbdiv * fin; + do_div(tmp, _prediv); + if (tmp < fvco_min || tmp > fvco_max) + continue; + + delta = abs(fout - tmp); + if (delta < min_delta) { + best_prediv = _prediv; + best_fbdiv = _fbdiv; + min_delta = delta; + best_freq = tmp; + } + } + + if (best_freq) { + dsi->lane_mbps = DIV_ROUND_UP(best_freq, USEC_PER_SEC); + *lane_mbps = dsi->lane_mbps; + dsi->input_div = best_prediv; + dsi->feedback_div = best_fbdiv; + } else { + DRM_DEV_ERROR(dsi->dev, "Can not find best_freq for DPHY\n"); + return -EINVAL; + } + + return 0; +} + +static const struct dw_mipi_dsi_phy_ops dw_mipi_dsi_rockchip_phy_ops = { + .init = dw_mipi_dsi_phy_init, + .get_lane_mbps = dw_mipi_dsi_get_lane_mbps, +}; + +static void dw_mipi_dsi_rockchip_config(struct dw_mipi_dsi_rockchip *dsi, + int mux) +{ + if (dsi->cdata->lcdsel_grf_reg) + regmap_write(dsi->grf_regmap, dsi->cdata->lcdsel_grf_reg, + mux ? dsi->cdata->lcdsel_lit : dsi->cdata->lcdsel_big); + + if (dsi->cdata->lanecfg1_grf_reg) + regmap_write(dsi->grf_regmap, dsi->cdata->lanecfg1_grf_reg, + dsi->cdata->lanecfg1); + + if (dsi->cdata->lanecfg2_grf_reg) + regmap_write(dsi->grf_regmap, dsi->cdata->lanecfg2_grf_reg, + dsi->cdata->lanecfg2); + + if (dsi->cdata->enable_grf_reg) + regmap_write(dsi->grf_regmap, dsi->cdata->enable_grf_reg, + dsi->cdata->enable); +} + +static int +dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder, + struct drm_crtc_state *crtc_state, + struct drm_connector_state *conn_state) +{ + struct rockchip_crtc_state *s = to_rockchip_crtc_state(crtc_state); + struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); + + switch (dsi->format) { + case MIPI_DSI_FMT_RGB888: + s->output_mode = ROCKCHIP_OUT_MODE_P888; + break; + case MIPI_DSI_FMT_RGB666: + s->output_mode = ROCKCHIP_OUT_MODE_P666; + break; + case MIPI_DSI_FMT_RGB565: + s->output_mode = ROCKCHIP_OUT_MODE_P565; + break; + default: + WARN_ON(1); + return -EINVAL; + } + + s->output_type = DRM_MODE_CONNECTOR_DSI; + + return 0; +} + +static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) +{ + struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); + int ret, mux; + + mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, + &dsi->encoder); + if (mux < 0) + return; + + pm_runtime_get_sync(dsi->dev); + + /* + * For the RK3399, the clk of grf must be enabled before writing grf + * register. And for RK3288 or other soc, this grf_clk must be NULL, + * the clk_prepare_enable return true directly. + */ + ret = clk_prepare_enable(dsi->grf_clk); + if (ret) { + DRM_DEV_ERROR(dsi->dev, "Failed to enable grf_clk: %d\n", ret); + return; + } + + dw_mipi_dsi_rockchip_config(dsi, mux); + + clk_disable_unprepare(dsi->grf_clk); +} + +static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) +{ + struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); + + pm_runtime_put(dsi->dev); +} + +static const struct drm_encoder_helper_funcs +dw_mipi_dsi_encoder_helper_funcs = { + .atomic_check = dw_mipi_dsi_encoder_atomic_check, + .enable = dw_mipi_dsi_encoder_enable, + .disable = dw_mipi_dsi_encoder_disable, +}; + +static const struct drm_encoder_funcs dw_mipi_dsi_encoder_funcs = { + .destroy = drm_encoder_cleanup, +}; + +static int rockchip_dsi_drm_create_encoder(struct dw_mipi_dsi_rockchip *dsi, + struct drm_device *drm_dev) +{ + struct drm_encoder *encoder = &dsi->encoder; + int ret; + + encoder->possible_crtcs = drm_of_find_possible_crtcs(drm_dev, + dsi->dev->of_node); + + ret = drm_encoder_init(drm_dev, encoder, &dw_mipi_dsi_encoder_funcs, + DRM_MODE_ENCODER_DSI, NULL); + if (ret) { + DRM_ERROR("Failed to initialize encoder with drm\n"); + return ret; + } + + drm_encoder_helper_add(encoder, &dw_mipi_dsi_encoder_helper_funcs); + + return 0; +} + +static int dw_mipi_dsi_rockchip_bind(struct device *dev, + struct device *master, + void *data) +{ + struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); + struct drm_device *drm_dev = data; + int ret; + + ret = clk_prepare_enable(dsi->pllref_clk); + if (ret) { + DRM_DEV_ERROR(dev, "Failed to enable pllref_clk: %d\n", ret); + return ret; + } + + ret = rockchip_dsi_drm_create_encoder(dsi, drm_dev); + if (ret) { + DRM_DEV_ERROR(dev, "Failed to create drm encoder\n"); + return ret; + } + + ret = dw_mipi_dsi_bind(dsi->dmd, &dsi->encoder); + if (ret) { + DRM_DEV_ERROR(dev, "Failed to bind: %d\n", ret); + return ret; + } + + return 0; +} + +static void dw_mipi_dsi_rockchip_unbind(struct device *dev, + struct device *master, + void *data) +{ + struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); + + dw_mipi_dsi_unbind(dsi->dmd); + + clk_disable_unprepare(dsi->pllref_clk); +} + +static const struct component_ops dw_mipi_dsi_rockchip_ops = { + .bind = dw_mipi_dsi_rockchip_bind, + .unbind = dw_mipi_dsi_rockchip_unbind, +}; + +static int dw_mipi_dsi_rockchip_host_attach(void *priv_data, + struct mipi_dsi_device *device) +{ + struct dw_mipi_dsi_rockchip *dsi = priv_data; + int ret; + + ret = component_add(dsi->dev, &dw_mipi_dsi_rockchip_ops); + if (ret) { + DRM_DEV_ERROR(dsi->dev, "Failed to register component: %d\n", + ret); + return ret; + } + + return 0; +} + +static int dw_mipi_dsi_rockchip_host_detach(void *priv_data, + struct mipi_dsi_device *device) +{ + struct dw_mipi_dsi_rockchip *dsi = priv_data; + + component_del(dsi->dev, &dw_mipi_dsi_rockchip_ops); + + return 0; +} + +static const struct dw_mipi_dsi_host_ops dw_mipi_dsi_rockchip_host_ops = { + .attach = dw_mipi_dsi_rockchip_host_attach, + .detach = dw_mipi_dsi_rockchip_host_detach, +}; + +static int dw_mipi_dsi_rockchip_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct dw_mipi_dsi_rockchip *dsi; + struct resource *res; + const struct rockchip_dw_dsi_chip_data *cdata = + of_device_get_match_data(dev); + int ret, i; + + dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL); + if (!dsi) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + dsi->base = devm_ioremap_resource(dev, res); + if (IS_ERR(dsi->base)) { + DRM_DEV_ERROR(dev, "Unable to get dsi registers\n"); + return PTR_ERR(dsi->base); + } + + i = 0; + while (cdata[i].reg) { + if (cdata[i].reg == res->start) { + dsi->cdata = &cdata[i]; + break; + } + + i++; + } + + if (!dsi->cdata) { + dev_err(dev, "no dsi-config for %s node\n", np->name); + return -EINVAL; + } + + dsi->pllref_clk = devm_clk_get(dev, "ref"); + if (IS_ERR(dsi->pllref_clk)) { + ret = PTR_ERR(dsi->pllref_clk); + DRM_DEV_ERROR(dev, + "Unable to get pll reference clock: %d\n", ret); + return ret; + } + + if (dsi->cdata->flags & DW_MIPI_NEEDS_PHY_CFG_CLK) { + dsi->phy_cfg_clk = devm_clk_get(dev, "phy_cfg"); + if (IS_ERR(dsi->phy_cfg_clk)) { + ret = PTR_ERR(dsi->phy_cfg_clk); + DRM_DEV_ERROR(dev, + "Unable to get phy_cfg_clk: %d\n", ret); + return ret; + } + } + + if (dsi->cdata->flags & DW_MIPI_NEEDS_GRF_CLK) { + dsi->grf_clk = devm_clk_get(dev, "grf"); + if (IS_ERR(dsi->grf_clk)) { + ret = PTR_ERR(dsi->grf_clk); + DRM_DEV_ERROR(dev, "Unable to get grf_clk: %d\n", ret); + return ret; + } + } + + dsi->grf_regmap = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); + if (IS_ERR(dsi->grf_regmap)) { + DRM_DEV_ERROR(dsi->dev, "Unable to get rockchip,grf\n"); + return PTR_ERR(dsi->grf_regmap); + } + + dsi->dev = dev; + dsi->pdata.base = dsi->base; + dsi->pdata.max_data_lanes = dsi->cdata->max_data_lanes; + dsi->pdata.phy_ops = &dw_mipi_dsi_rockchip_phy_ops; + dsi->pdata.host_ops = &dw_mipi_dsi_rockchip_host_ops; + dsi->pdata.priv_data = dsi; + platform_set_drvdata(pdev, dsi); + + dsi->dmd = dw_mipi_dsi_probe(pdev, &dsi->pdata); + if (IS_ERR(dsi->dmd)) { + ret = PTR_ERR(dsi->dmd); + if (ret != -EPROBE_DEFER) + DRM_DEV_ERROR(dev, + "Failed to probe dw_mipi_dsi: %d\n", ret); + goto err_clkdisable; + } + + return 0; + +err_clkdisable: + clk_disable_unprepare(dsi->pllref_clk); + return ret; +} + +static int dw_mipi_dsi_rockchip_remove(struct platform_device *pdev) +{ + struct dw_mipi_dsi_rockchip *dsi = platform_get_drvdata(pdev); + + dw_mipi_dsi_remove(dsi->dmd); + + return 0; +} + +static const struct rockchip_dw_dsi_chip_data rk3288_chip_data[] = { + { + .reg = 0xff960000, + .lcdsel_grf_reg = RK3288_GRF_SOC_CON6, + .lcdsel_big = HIWORD_UPDATE(0, RK3288_DSI0_LCDC_SEL), + .lcdsel_lit = HIWORD_UPDATE(RK3288_DSI0_LCDC_SEL, RK3288_DSI0_LCDC_SEL), + + .max_data_lanes = 4, + }, + { + .reg = 0xff964000, + .lcdsel_grf_reg = RK3288_GRF_SOC_CON6, + .lcdsel_big = HIWORD_UPDATE(0, RK3288_DSI1_LCDC_SEL), + .lcdsel_lit = HIWORD_UPDATE(RK3288_DSI1_LCDC_SEL, RK3288_DSI1_LCDC_SEL), + + .max_data_lanes = 4, + }, + { /* sentinel */ } +}; + +static const struct rockchip_dw_dsi_chip_data rk3399_chip_data[] = { + { + .reg = 0xff960000, + .lcdsel_grf_reg = RK3399_GRF_SOC_CON20, + .lcdsel_big = HIWORD_UPDATE(0, RK3399_DSI0_LCDC_SEL), + .lcdsel_lit = HIWORD_UPDATE(RK3399_DSI0_LCDC_SEL, + RK3399_DSI0_LCDC_SEL), + + .lanecfg1_grf_reg = RK3399_GRF_SOC_CON22, + .lanecfg1 = HIWORD_UPDATE(0, RK3399_DSI0_TURNREQUEST | + RK3399_DSI0_TURNDISABLE | + RK3399_DSI0_FORCETXSTOPMODE | + RK3399_DSI0_FORCERXMODE), + + .flags = DW_MIPI_NEEDS_PHY_CFG_CLK | DW_MIPI_NEEDS_GRF_CLK, + .max_data_lanes = 4, + }, + { + .reg = 0xff968000, + .lcdsel_grf_reg = RK3399_GRF_SOC_CON20, + .lcdsel_big = HIWORD_UPDATE(0, RK3399_DSI1_LCDC_SEL), + .lcdsel_lit = HIWORD_UPDATE(RK3399_DSI1_LCDC_SEL, + RK3399_DSI1_LCDC_SEL), + + .lanecfg1_grf_reg = RK3399_GRF_SOC_CON23, + .lanecfg1 = HIWORD_UPDATE(0, RK3399_DSI1_TURNDISABLE | + RK3399_DSI1_FORCETXSTOPMODE | + RK3399_DSI1_FORCERXMODE | + RK3399_DSI1_ENABLE), + + .lanecfg2_grf_reg = RK3399_GRF_SOC_CON24, + .lanecfg2 = HIWORD_UPDATE(RK3399_TXRX_MASTERSLAVEZ | + RK3399_TXRX_ENABLECLK, + RK3399_TXRX_MASTERSLAVEZ | + RK3399_TXRX_ENABLECLK | + RK3399_TXRX_BASEDIR), + + .enable_grf_reg = RK3399_GRF_SOC_CON23, + .enable = HIWORD_UPDATE(RK3399_DSI1_ENABLE, RK3399_DSI1_ENABLE), + + .flags = DW_MIPI_NEEDS_PHY_CFG_CLK | DW_MIPI_NEEDS_GRF_CLK, + .max_data_lanes = 4, + }, + { /* sentinel */ } +}; + +static const struct of_device_id dw_mipi_dsi_rockchip_dt_ids[] = { + { + .compatible = "rockchip,rk3288-mipi-dsi", + .data = &rk3288_chip_data, + }, { + .compatible = "rockchip,rk3399-mipi-dsi", + .data = &rk3399_chip_data, + }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, dw_mipi_dsi_rockchip_dt_ids); + +struct platform_driver dw_mipi_dsi_rockchip_driver = { + .probe = dw_mipi_dsi_rockchip_probe, + .remove = dw_mipi_dsi_rockchip_remove, + .driver = { + .of_match_table = dw_mipi_dsi_rockchip_dt_ids, + .name = "dw-mipi-dsi-rockchip", + }, +}; diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c deleted file mode 100644 index 662b6cb5d3f0..000000000000 --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c +++ /dev/null @@ -1,1349 +0,0 @@ -/* - * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ -#include <linux/clk.h> -#include <linux/component.h> -#include <linux/iopoll.h> -#include <linux/math64.h> -#include <linux/module.h> -#include <linux/of_device.h> -#include <linux/pm_runtime.h> -#include <linux/regmap.h> -#include <linux/reset.h> -#include <linux/mfd/syscon.h> -#include <drm/drm_atomic_helper.h> -#include <drm/drm_crtc.h> -#include <drm/drm_crtc_helper.h> -#include <drm/drm_mipi_dsi.h> -#include <drm/drm_of.h> -#include <drm/drm_panel.h> -#include <drm/drmP.h> -#include <video/mipi_display.h> - -#include "rockchip_drm_drv.h" -#include "rockchip_drm_vop.h" - -#define DRIVER_NAME "dw-mipi-dsi" - -#define RK3288_GRF_SOC_CON6 0x025c -#define RK3288_DSI0_SEL_VOP_LIT BIT(6) -#define RK3288_DSI1_SEL_VOP_LIT BIT(9) - -#define RK3399_GRF_SOC_CON20 0x6250 -#define RK3399_DSI0_SEL_VOP_LIT BIT(0) -#define RK3399_DSI1_SEL_VOP_LIT BIT(4) - -/* disable turnrequest, turndisable, forcetxstopmode, forcerxmode */ -#define RK3399_GRF_SOC_CON22 0x6258 -#define RK3399_GRF_DSI_MODE 0xffff0000 - -#define DSI_VERSION 0x00 -#define DSI_PWR_UP 0x04 -#define RESET 0 -#define POWERUP BIT(0) - -#define DSI_CLKMGR_CFG 0x08 -#define TO_CLK_DIVIDSION(div) (((div) & 0xff) << 8) -#define TX_ESC_CLK_DIVIDSION(div) (((div) & 0xff) << 0) - -#define DSI_DPI_VCID 0x0c -#define DPI_VID(vid) (((vid) & 0x3) << 0) - -#define DSI_DPI_COLOR_CODING 0x10 -#define EN18_LOOSELY BIT(8) -#define DPI_COLOR_CODING_16BIT_1 0x0 -#define DPI_COLOR_CODING_16BIT_2 0x1 -#define DPI_COLOR_CODING_16BIT_3 0x2 -#define DPI_COLOR_CODING_18BIT_1 0x3 -#define DPI_COLOR_CODING_18BIT_2 0x4 -#define DPI_COLOR_CODING_24BIT 0x5 - -#define DSI_DPI_CFG_POL 0x14 -#define COLORM_ACTIVE_LOW BIT(4) -#define SHUTD_ACTIVE_LOW BIT(3) -#define HSYNC_ACTIVE_LOW BIT(2) -#define VSYNC_ACTIVE_LOW BIT(1) -#define DATAEN_ACTIVE_LOW BIT(0) - -#define DSI_DPI_LP_CMD_TIM 0x18 -#define OUTVACT_LPCMD_TIME(p) (((p) & 0xff) << 16) -#define INVACT_LPCMD_TIME(p) ((p) & 0xff) - -#define DSI_DBI_CFG 0x20 -#define DSI_DBI_CMDSIZE 0x28 - -#define DSI_PCKHDL_CFG 0x2c -#define EN_CRC_RX BIT(4) -#define EN_ECC_RX BIT(3) -#define EN_BTA BIT(2) -#define EN_EOTP_RX BIT(1) -#define EN_EOTP_TX BIT(0) - -#define DSI_MODE_CFG 0x34 -#define ENABLE_VIDEO_MODE 0 -#define ENABLE_CMD_MODE BIT(0) - -#define DSI_VID_MODE_CFG 0x38 -#define FRAME_BTA_ACK BIT(14) -#define ENABLE_LOW_POWER (0x3f << 8) -#define ENABLE_LOW_POWER_MASK (0x3f << 8) -#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES 0x0 -#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS 0x1 -#define VID_MODE_TYPE_BURST 0x2 -#define VID_MODE_TYPE_MASK 0x3 - -#define DSI_VID_PKT_SIZE 0x3c -#define VID_PKT_SIZE(p) (((p) & 0x3fff) << 0) -#define VID_PKT_MAX_SIZE 0x3fff - -#define DSI_VID_HSA_TIME 0x48 -#define DSI_VID_HBP_TIME 0x4c -#define DSI_VID_HLINE_TIME 0x50 -#define DSI_VID_VSA_LINES 0x54 -#define DSI_VID_VBP_LINES 0x58 -#define DSI_VID_VFP_LINES 0x5c -#define DSI_VID_VACTIVE_LINES 0x60 -#define DSI_CMD_MODE_CFG 0x68 -#define MAX_RD_PKT_SIZE_LP BIT(24) -#define DCS_LW_TX_LP BIT(19) -#define DCS_SR_0P_TX_LP BIT(18) -#define DCS_SW_1P_TX_LP BIT(17) -#define DCS_SW_0P_TX_LP BIT(16) -#define GEN_LW_TX_LP BIT(14) -#define GEN_SR_2P_TX_LP BIT(13) -#define GEN_SR_1P_TX_LP BIT(12) -#define GEN_SR_0P_TX_LP BIT(11) -#define GEN_SW_2P_TX_LP BIT(10) -#define GEN_SW_1P_TX_LP BIT(9) -#define GEN_SW_0P_TX_LP BIT(8) -#define EN_ACK_RQST BIT(1) -#define EN_TEAR_FX BIT(0) - -#define CMD_MODE_ALL_LP (MAX_RD_PKT_SIZE_LP | \ - DCS_LW_TX_LP | \ - DCS_SR_0P_TX_LP | \ - DCS_SW_1P_TX_LP | \ - DCS_SW_0P_TX_LP | \ - GEN_LW_TX_LP | \ - GEN_SR_2P_TX_LP | \ - GEN_SR_1P_TX_LP | \ - GEN_SR_0P_TX_LP | \ - GEN_SW_2P_TX_LP | \ - GEN_SW_1P_TX_LP | \ - GEN_SW_0P_TX_LP) - -#define DSI_GEN_HDR 0x6c -#define GEN_HDATA(data) (((data) & 0xffff) << 8) -#define GEN_HDATA_MASK (0xffff << 8) -#define GEN_HTYPE(type) (((type) & 0xff) << 0) -#define GEN_HTYPE_MASK 0xff - -#define DSI_GEN_PLD_DATA 0x70 - -#define DSI_CMD_PKT_STATUS 0x74 -#define GEN_CMD_EMPTY BIT(0) -#define GEN_CMD_FULL BIT(1) -#define GEN_PLD_W_EMPTY BIT(2) -#define GEN_PLD_W_FULL BIT(3) -#define GEN_PLD_R_EMPTY BIT(4) -#define GEN_PLD_R_FULL BIT(5) -#define GEN_RD_CMD_BUSY BIT(6) - -#define DSI_TO_CNT_CFG 0x78 -#define HSTX_TO_CNT(p) (((p) & 0xffff) << 16) -#define LPRX_TO_CNT(p) ((p) & 0xffff) - -#define DSI_BTA_TO_CNT 0x8c -#define DSI_LPCLK_CTRL 0x94 -#define AUTO_CLKLANE_CTRL BIT(1) -#define PHY_TXREQUESTCLKHS BIT(0) - -#define DSI_PHY_TMR_LPCLK_CFG 0x98 -#define PHY_CLKHS2LP_TIME(lbcc) (((lbcc) & 0x3ff) << 16) -#define PHY_CLKLP2HS_TIME(lbcc) ((lbcc) & 0x3ff) - -#define DSI_PHY_TMR_CFG 0x9c -#define PHY_HS2LP_TIME(lbcc) (((lbcc) & 0xff) << 24) -#define PHY_LP2HS_TIME(lbcc) (((lbcc) & 0xff) << 16) -#define MAX_RD_TIME(lbcc) ((lbcc) & 0x7fff) - -#define DSI_PHY_RSTZ 0xa0 -#define PHY_DISFORCEPLL 0 -#define PHY_ENFORCEPLL BIT(3) -#define PHY_DISABLECLK 0 -#define PHY_ENABLECLK BIT(2) -#define PHY_RSTZ 0 -#define PHY_UNRSTZ BIT(1) -#define PHY_SHUTDOWNZ 0 -#define PHY_UNSHUTDOWNZ BIT(0) - -#define DSI_PHY_IF_CFG 0xa4 -#define N_LANES(n) ((((n) - 1) & 0x3) << 0) -#define PHY_STOP_WAIT_TIME(cycle) (((cycle) & 0xff) << 8) - -#define DSI_PHY_STATUS 0xb0 -#define LOCK BIT(0) -#define STOP_STATE_CLK_LANE BIT(2) - -#define DSI_PHY_TST_CTRL0 0xb4 -#define PHY_TESTCLK BIT(1) -#define PHY_UNTESTCLK 0 -#define PHY_TESTCLR BIT(0) -#define PHY_UNTESTCLR 0 - -#define DSI_PHY_TST_CTRL1 0xb8 -#define PHY_TESTEN BIT(16) -#define PHY_UNTESTEN 0 -#define PHY_TESTDOUT(n) (((n) & 0xff) << 8) -#define PHY_TESTDIN(n) (((n) & 0xff) << 0) - -#define DSI_INT_ST0 0xbc -#define DSI_INT_ST1 0xc0 -#define DSI_INT_MSK0 0xc4 -#define DSI_INT_MSK1 0xc8 - -#define PHY_STATUS_TIMEOUT_US 10000 -#define CMD_PKT_STATUS_TIMEOUT_US 20000 - -#define BYPASS_VCO_RANGE BIT(7) -#define VCO_RANGE_CON_SEL(val) (((val) & 0x7) << 3) -#define VCO_IN_CAP_CON_DEFAULT (0x0 << 1) -#define VCO_IN_CAP_CON_LOW (0x1 << 1) -#define VCO_IN_CAP_CON_HIGH (0x2 << 1) -#define REF_BIAS_CUR_SEL BIT(0) - -#define CP_CURRENT_3MA BIT(3) -#define CP_PROGRAM_EN BIT(7) -#define LPF_PROGRAM_EN BIT(6) -#define LPF_RESISTORS_20_KOHM 0 - -#define HSFREQRANGE_SEL(val) (((val) & 0x3f) << 1) - -#define INPUT_DIVIDER(val) (((val) - 1) & 0x7f) -#define LOW_PROGRAM_EN 0 -#define HIGH_PROGRAM_EN BIT(7) -#define LOOP_DIV_LOW_SEL(val) (((val) - 1) & 0x1f) -#define LOOP_DIV_HIGH_SEL(val) ((((val) - 1) >> 5) & 0x1f) -#define PLL_LOOP_DIV_EN BIT(5) -#define PLL_INPUT_DIV_EN BIT(4) - -#define POWER_CONTROL BIT(6) -#define INTERNAL_REG_CURRENT BIT(3) -#define BIAS_BLOCK_ON BIT(2) -#define BANDGAP_ON BIT(0) - -#define TER_RESISTOR_HIGH BIT(7) -#define TER_RESISTOR_LOW 0 -#define LEVEL_SHIFTERS_ON BIT(6) -#define TER_CAL_DONE BIT(5) -#define SETRD_MAX (0x7 << 2) -#define POWER_MANAGE BIT(1) -#define TER_RESISTORS_ON BIT(0) - -#define BIASEXTR_SEL(val) ((val) & 0x7) -#define BANDGAP_SEL(val) ((val) & 0x7) -#define TLP_PROGRAM_EN BIT(7) -#define THS_PRE_PROGRAM_EN BIT(7) -#define THS_ZERO_PROGRAM_EN BIT(6) - -#define DW_MIPI_NEEDS_PHY_CFG_CLK BIT(0) -#define DW_MIPI_NEEDS_GRF_CLK BIT(1) - -enum { - BANDGAP_97_07, - BANDGAP_98_05, - BANDGAP_99_02, - BANDGAP_100_00, - BANDGAP_93_17, - BANDGAP_94_15, - BANDGAP_95_12, - BANDGAP_96_10, -}; - -enum { - BIASEXTR_87_1, - BIASEXTR_91_5, - BIASEXTR_95_9, - BIASEXTR_100, - BIASEXTR_105_94, - BIASEXTR_111_88, - BIASEXTR_118_8, - BIASEXTR_127_7, -}; - -struct dw_mipi_dsi_plat_data { - u32 dsi0_en_bit; - u32 dsi1_en_bit; - u32 grf_switch_reg; - u32 grf_dsi0_mode; - u32 grf_dsi0_mode_reg; - unsigned int flags; - unsigned int max_data_lanes; -}; - -struct dw_mipi_dsi { - struct drm_encoder encoder; - struct drm_connector connector; - struct mipi_dsi_host dsi_host; - struct drm_panel *panel; - struct device *dev; - struct regmap *grf_regmap; - void __iomem *base; - - struct clk *grf_clk; - struct clk *pllref_clk; - struct clk *pclk; - struct clk *phy_cfg_clk; - - int dpms_mode; - unsigned int lane_mbps; /* per lane */ - u32 channel; - u32 lanes; - u32 format; - u16 input_div; - u16 feedback_div; - unsigned long mode_flags; - - const struct dw_mipi_dsi_plat_data *pdata; -}; - -enum dw_mipi_dsi_mode { - DW_MIPI_DSI_CMD_MODE, - DW_MIPI_DSI_VID_MODE, -}; - -struct dphy_pll_testdin_map { - unsigned int max_mbps; - u8 testdin; -}; - -/* The table is based on 27MHz DPHY pll reference clock. */ -static const struct dphy_pll_testdin_map dptdin_map[] = { - { 90, 0x00}, { 100, 0x10}, { 110, 0x20}, { 130, 0x01}, - { 140, 0x11}, { 150, 0x21}, { 170, 0x02}, { 180, 0x12}, - { 200, 0x22}, { 220, 0x03}, { 240, 0x13}, { 250, 0x23}, - { 270, 0x04}, { 300, 0x14}, { 330, 0x05}, { 360, 0x15}, - { 400, 0x25}, { 450, 0x06}, { 500, 0x16}, { 550, 0x07}, - { 600, 0x17}, { 650, 0x08}, { 700, 0x18}, { 750, 0x09}, - { 800, 0x19}, { 850, 0x29}, { 900, 0x39}, { 950, 0x0a}, - {1000, 0x1a}, {1050, 0x2a}, {1100, 0x3a}, {1150, 0x0b}, - {1200, 0x1b}, {1250, 0x2b}, {1300, 0x3b}, {1350, 0x0c}, - {1400, 0x1c}, {1450, 0x2c}, {1500, 0x3c} -}; - -static int max_mbps_to_testdin(unsigned int max_mbps) -{ - int i; - - for (i = 0; i < ARRAY_SIZE(dptdin_map); i++) - if (dptdin_map[i].max_mbps > max_mbps) - return dptdin_map[i].testdin; - - return -EINVAL; -} - -/* - * The controller should generate 2 frames before - * preparing the peripheral. - */ -static void dw_mipi_dsi_wait_for_two_frames(struct drm_display_mode *mode) -{ - int refresh, two_frames; - - refresh = drm_mode_vrefresh(mode); - two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2; - msleep(two_frames); -} - -static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host) -{ - return container_of(host, struct dw_mipi_dsi, dsi_host); -} - -static inline struct dw_mipi_dsi *con_to_dsi(struct drm_connector *con) -{ - return container_of(con, struct dw_mipi_dsi, connector); -} - -static inline struct dw_mipi_dsi *encoder_to_dsi(struct drm_encoder *encoder) -{ - return container_of(encoder, struct dw_mipi_dsi, encoder); -} - -static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val) -{ - writel(val, dsi->base + reg); -} - -static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg) -{ - return readl(dsi->base + reg); -} - -static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi *dsi, u8 test_code, - u8 test_data) -{ - /* - * With the falling edge on TESTCLK, the TESTDIN[7:0] signal content - * is latched internally as the current test code. Test data is - * programmed internally by rising edge on TESTCLK. - */ - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); - - dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_TESTEN | PHY_TESTDOUT(0) | - PHY_TESTDIN(test_code)); - - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLK | PHY_UNTESTCLR); - - dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_UNTESTEN | PHY_TESTDOUT(0) | - PHY_TESTDIN(test_data)); - - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); -} - -/** - * ns2bc - Nanoseconds to byte clock cycles - */ -static inline unsigned int ns2bc(struct dw_mipi_dsi *dsi, int ns) -{ - return DIV_ROUND_UP(ns * dsi->lane_mbps / 8, 1000); -} - -/** - * ns2ui - Nanoseconds to UI time periods - */ -static inline unsigned int ns2ui(struct dw_mipi_dsi *dsi, int ns) -{ - return DIV_ROUND_UP(ns * dsi->lane_mbps, 1000); -} - -static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi) -{ - int ret, testdin, vco, val; - - vco = (dsi->lane_mbps < 200) ? 0 : (dsi->lane_mbps + 100) / 200; - - testdin = max_mbps_to_testdin(dsi->lane_mbps); - if (testdin < 0) { - DRM_DEV_ERROR(dsi->dev, - "failed to get testdin for %dmbps lane clock\n", - dsi->lane_mbps); - return testdin; - } - - /* Start by clearing PHY state */ - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR); - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR); - dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR); - - ret = clk_prepare_enable(dsi->phy_cfg_clk); - if (ret) { - DRM_DEV_ERROR(dsi->dev, "Failed to enable phy_cfg_clk\n"); - return ret; - } - - dw_mipi_dsi_phy_write(dsi, 0x10, BYPASS_VCO_RANGE | - VCO_RANGE_CON_SEL(vco) | - VCO_IN_CAP_CON_LOW | - REF_BIAS_CUR_SEL); - - dw_mipi_dsi_phy_write(dsi, 0x11, CP_CURRENT_3MA); - dw_mipi_dsi_phy_write(dsi, 0x12, CP_PROGRAM_EN | LPF_PROGRAM_EN | - LPF_RESISTORS_20_KOHM); - - dw_mipi_dsi_phy_write(dsi, 0x44, HSFREQRANGE_SEL(testdin)); - - dw_mipi_dsi_phy_write(dsi, 0x17, INPUT_DIVIDER(dsi->input_div)); - dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_LOW_SEL(dsi->feedback_div) | - LOW_PROGRAM_EN); - dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_HIGH_SEL(dsi->feedback_div) | - HIGH_PROGRAM_EN); - dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN); - - dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN | - BIASEXTR_SEL(BIASEXTR_127_7)); - dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN | - BANDGAP_SEL(BANDGAP_96_10)); - - dw_mipi_dsi_phy_write(dsi, 0x20, POWER_CONTROL | INTERNAL_REG_CURRENT | - BIAS_BLOCK_ON | BANDGAP_ON); - - dw_mipi_dsi_phy_write(dsi, 0x21, TER_RESISTOR_LOW | TER_CAL_DONE | - SETRD_MAX | TER_RESISTORS_ON); - dw_mipi_dsi_phy_write(dsi, 0x21, TER_RESISTOR_HIGH | LEVEL_SHIFTERS_ON | - SETRD_MAX | POWER_MANAGE | - TER_RESISTORS_ON); - - dw_mipi_dsi_phy_write(dsi, 0x60, TLP_PROGRAM_EN | ns2bc(dsi, 500)); - dw_mipi_dsi_phy_write(dsi, 0x61, THS_PRE_PROGRAM_EN | ns2ui(dsi, 40)); - dw_mipi_dsi_phy_write(dsi, 0x62, THS_ZERO_PROGRAM_EN | ns2bc(dsi, 300)); - dw_mipi_dsi_phy_write(dsi, 0x63, THS_PRE_PROGRAM_EN | ns2ui(dsi, 100)); - dw_mipi_dsi_phy_write(dsi, 0x64, BIT(5) | ns2bc(dsi, 100)); - dw_mipi_dsi_phy_write(dsi, 0x65, BIT(5) | (ns2bc(dsi, 60) + 7)); - - dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | ns2bc(dsi, 500)); - dw_mipi_dsi_phy_write(dsi, 0x71, - THS_PRE_PROGRAM_EN | (ns2ui(dsi, 50) + 5)); - dw_mipi_dsi_phy_write(dsi, 0x72, - THS_ZERO_PROGRAM_EN | (ns2bc(dsi, 140) + 2)); - dw_mipi_dsi_phy_write(dsi, 0x73, - THS_PRE_PROGRAM_EN | (ns2ui(dsi, 60) + 8)); - dw_mipi_dsi_phy_write(dsi, 0x74, BIT(5) | ns2bc(dsi, 100)); - - dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK | - PHY_UNRSTZ | PHY_UNSHUTDOWNZ); - - ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS, - val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US); - if (ret < 0) { - DRM_DEV_ERROR(dsi->dev, "failed to wait for phy lock state\n"); - goto phy_init_end; - } - - ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS, - val, val & STOP_STATE_CLK_LANE, 1000, - PHY_STATUS_TIMEOUT_US); - if (ret < 0) - DRM_DEV_ERROR(dsi->dev, - "failed to wait for phy clk lane stop state\n"); - -phy_init_end: - clk_disable_unprepare(dsi->phy_cfg_clk); - - return ret; -} - -static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode) -{ - unsigned int i, pre; - unsigned long mpclk, pllref, tmp; - unsigned int m = 1, n = 1, target_mbps = 1000; - unsigned int max_mbps = dptdin_map[ARRAY_SIZE(dptdin_map) - 1].max_mbps; - int bpp; - - bpp = mipi_dsi_pixel_format_to_bpp(dsi->format); - if (bpp < 0) { - DRM_DEV_ERROR(dsi->dev, - "failed to get bpp for pixel format %d\n", - dsi->format); - return bpp; - } - - mpclk = DIV_ROUND_UP(mode->clock, MSEC_PER_SEC); - if (mpclk) { - /* take 1 / 0.8, since mbps must big than bandwidth of RGB */ - tmp = mpclk * (bpp / dsi->lanes) * 10 / 8; - if (tmp < max_mbps) - target_mbps = tmp; - else - DRM_DEV_ERROR(dsi->dev, - "DPHY clock frequency is out of range\n"); - } - - pllref = DIV_ROUND_UP(clk_get_rate(dsi->pllref_clk), USEC_PER_SEC); - tmp = pllref; - - /* - * The limits on the PLL divisor are: - * - * 5MHz <= (pllref / n) <= 40MHz - * - * we walk over these values in descreasing order so that if we hit - * an exact match for target_mbps it is more likely that "m" will be - * even. - * - * TODO: ensure that "m" is even after this loop. - */ - for (i = pllref / 5; i > (pllref / 40); i--) { - pre = pllref / i; - if ((tmp > (target_mbps % pre)) && (target_mbps / pre < 512)) { - tmp = target_mbps % pre; - n = i; - m = target_mbps / pre; - } - if (tmp == 0) - break; - } - - dsi->lane_mbps = pllref / n * m; - dsi->input_div = n; - dsi->feedback_div = m; - - return 0; -} - -static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host, - struct mipi_dsi_device *device) -{ - struct dw_mipi_dsi *dsi = host_to_dsi(host); - - if (device->lanes > dsi->pdata->max_data_lanes) { - DRM_DEV_ERROR(dsi->dev, - "the number of data lanes(%u) is too many\n", - device->lanes); - return -EINVAL; - } - - dsi->lanes = device->lanes; - dsi->channel = device->channel; - dsi->format = device->format; - dsi->mode_flags = device->mode_flags; - dsi->panel = of_drm_find_panel(device->dev.of_node); - if (!IS_ERR(dsi->panel)) - return drm_panel_attach(dsi->panel, &dsi->connector); - - return -EINVAL; -} - -static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host, - struct mipi_dsi_device *device) -{ - struct dw_mipi_dsi *dsi = host_to_dsi(host); - - drm_panel_detach(dsi->panel); - - return 0; -} - -static void dw_mipi_message_config(struct dw_mipi_dsi *dsi, - const struct mipi_dsi_msg *msg) -{ - bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM; - u32 val = 0; - - if (msg->flags & MIPI_DSI_MSG_REQ_ACK) - val |= EN_ACK_RQST; - if (lpm) - val |= CMD_MODE_ALL_LP; - - dsi_write(dsi, DSI_LPCLK_CTRL, lpm ? 0 : PHY_TXREQUESTCLKHS); - dsi_write(dsi, DSI_CMD_MODE_CFG, val); -} - -static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val) -{ - int ret; - u32 val, mask; - - ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS, - val, !(val & GEN_CMD_FULL), 1000, - CMD_PKT_STATUS_TIMEOUT_US); - if (ret < 0) { - DRM_DEV_ERROR(dsi->dev, - "failed to get available command FIFO\n"); - return ret; - } - - dsi_write(dsi, DSI_GEN_HDR, hdr_val); - - mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY; - ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS, - val, (val & mask) == mask, - 1000, CMD_PKT_STATUS_TIMEOUT_US); - if (ret < 0) { - DRM_DEV_ERROR(dsi->dev, "failed to write command FIFO\n"); - return ret; - } - - return 0; -} - -static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi, - const struct mipi_dsi_msg *msg) -{ - const u8 *tx_buf = msg->tx_buf; - u16 data = 0; - u32 val; - - if (msg->tx_len > 0) - data |= tx_buf[0]; - if (msg->tx_len > 1) - data |= tx_buf[1] << 8; - - if (msg->tx_len > 2) { - DRM_DEV_ERROR(dsi->dev, - "too long tx buf length %zu for short write\n", - msg->tx_len); - return -EINVAL; - } - - val = GEN_HDATA(data) | GEN_HTYPE(msg->type); - return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val); -} - -static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi, - const struct mipi_dsi_msg *msg) -{ - const u8 *tx_buf = msg->tx_buf; - int len = msg->tx_len, pld_data_bytes = sizeof(u32), ret; - u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type); - u32 remainder; - u32 val; - - if (msg->tx_len < 3) { - DRM_DEV_ERROR(dsi->dev, - "wrong tx buf length %zu for long write\n", - msg->tx_len); - return -EINVAL; - } - - while (DIV_ROUND_UP(len, pld_data_bytes)) { - if (len < pld_data_bytes) { - remainder = 0; - memcpy(&remainder, tx_buf, len); - dsi_write(dsi, DSI_GEN_PLD_DATA, remainder); - len = 0; - } else { - memcpy(&remainder, tx_buf, pld_data_bytes); - dsi_write(dsi, DSI_GEN_PLD_DATA, remainder); - tx_buf += pld_data_bytes; - len -= pld_data_bytes; - } - - ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS, - val, !(val & GEN_PLD_W_FULL), 1000, - CMD_PKT_STATUS_TIMEOUT_US); - if (ret < 0) { - DRM_DEV_ERROR(dsi->dev, - "failed to get available write payload FIFO\n"); - return ret; - } - } - - return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val); -} - -static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host, - const struct mipi_dsi_msg *msg) -{ - struct dw_mipi_dsi *dsi = host_to_dsi(host); - int ret; - - dw_mipi_message_config(dsi, msg); - - switch (msg->type) { - case MIPI_DSI_DCS_SHORT_WRITE: - case MIPI_DSI_DCS_SHORT_WRITE_PARAM: - case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE: - ret = dw_mipi_dsi_dcs_short_write(dsi, msg); - break; - case MIPI_DSI_DCS_LONG_WRITE: - ret = dw_mipi_dsi_dcs_long_write(dsi, msg); - break; - default: - DRM_DEV_ERROR(dsi->dev, "unsupported message type 0x%02x\n", - msg->type); - ret = -EINVAL; - } - - return ret; -} - -static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = { - .attach = dw_mipi_dsi_host_attach, - .detach = dw_mipi_dsi_host_detach, - .transfer = dw_mipi_dsi_host_transfer, -}; - -static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi) -{ - u32 val; - - val = ENABLE_LOW_POWER; - - if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) - val |= VID_MODE_TYPE_BURST; - else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE) - val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES; - else - val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS; - - dsi_write(dsi, DSI_VID_MODE_CFG, val); -} - -static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi, - enum dw_mipi_dsi_mode mode) -{ - if (mode == DW_MIPI_DSI_CMD_MODE) { - dsi_write(dsi, DSI_PWR_UP, RESET); - dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE); - dsi_write(dsi, DSI_PWR_UP, POWERUP); - } else { - dsi_write(dsi, DSI_PWR_UP, RESET); - dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE); - dw_mipi_dsi_video_mode_config(dsi); - dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS); - dsi_write(dsi, DSI_PWR_UP, POWERUP); - } -} - -static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi) -{ - dsi_write(dsi, DSI_PWR_UP, RESET); - dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ); -} - -static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi) -{ - /* - * The maximum permitted escape clock is 20MHz and it is derived from - * lanebyteclk, which is running at "lane_mbps / 8". Thus we want: - * - * (lane_mbps >> 3) / esc_clk_division < 20 - * which is: - * (lane_mbps >> 3) / 20 > esc_clk_division - */ - u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1; - - dsi_write(dsi, DSI_PWR_UP, RESET); - dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK - | PHY_RSTZ | PHY_SHUTDOWNZ); - dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) | - TX_ESC_CLK_DIVIDSION(esc_clk_division)); -} - -static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode) -{ - u32 val = 0, color = 0; - - switch (dsi->format) { - case MIPI_DSI_FMT_RGB888: - color = DPI_COLOR_CODING_24BIT; - break; - case MIPI_DSI_FMT_RGB666: - color = DPI_COLOR_CODING_18BIT_2 | EN18_LOOSELY; - break; - case MIPI_DSI_FMT_RGB666_PACKED: - color = DPI_COLOR_CODING_18BIT_1; - break; - case MIPI_DSI_FMT_RGB565: - color = DPI_COLOR_CODING_16BIT_1; - break; - } - - if (mode->flags & DRM_MODE_FLAG_NVSYNC) - val |= VSYNC_ACTIVE_LOW; - if (mode->flags & DRM_MODE_FLAG_NHSYNC) - val |= HSYNC_ACTIVE_LOW; - - dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel)); - dsi_write(dsi, DSI_DPI_COLOR_CODING, color); - dsi_write(dsi, DSI_DPI_CFG_POL, val); - dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(4) - | INVACT_LPCMD_TIME(4)); -} - -static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi) -{ - dsi_write(dsi, DSI_PCKHDL_CFG, EN_CRC_RX | EN_ECC_RX | EN_BTA); -} - -static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode) -{ - dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay)); -} - -static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi) -{ - dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000)); - dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00); - dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE); -} - -/* Get lane byte clock cycles. */ -static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode, - u32 hcomponent) -{ - u32 frac, lbcc; - - lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8; - - frac = lbcc % mode->clock; - lbcc = lbcc / mode->clock; - if (frac) - lbcc++; - - return lbcc; -} - -static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode) -{ - u32 htotal, hsa, hbp, lbcc; - - htotal = mode->htotal; - hsa = mode->hsync_end - mode->hsync_start; - hbp = mode->htotal - mode->hsync_end; - - lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal); - dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc); - - lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa); - dsi_write(dsi, DSI_VID_HSA_TIME, lbcc); - - lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp); - dsi_write(dsi, DSI_VID_HBP_TIME, lbcc); -} - -static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi, - struct drm_display_mode *mode) -{ - u32 vactive, vsa, vfp, vbp; - - vactive = mode->vdisplay; - vsa = mode->vsync_end - mode->vsync_start; - vfp = mode->vsync_start - mode->vdisplay; - vbp = mode->vtotal - mode->vsync_end; - - dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive); - dsi_write(dsi, DSI_VID_VSA_LINES, vsa); - dsi_write(dsi, DSI_VID_VFP_LINES, vfp); - dsi_write(dsi, DSI_VID_VBP_LINES, vbp); -} - -static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi) -{ - dsi_write(dsi, DSI_PHY_TMR_CFG, PHY_HS2LP_TIME(0x40) - | PHY_LP2HS_TIME(0x40) | MAX_RD_TIME(10000)); - - dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG, PHY_CLKHS2LP_TIME(0x40) - | PHY_CLKLP2HS_TIME(0x40)); -} - -static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi) -{ - dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) | - N_LANES(dsi->lanes)); -} - -static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi) -{ - dsi_read(dsi, DSI_INT_ST0); - dsi_read(dsi, DSI_INT_ST1); - dsi_write(dsi, DSI_INT_MSK0, 0); - dsi_write(dsi, DSI_INT_MSK1, 0); -} - -static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) -{ - struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder); - - if (dsi->dpms_mode != DRM_MODE_DPMS_ON) - return; - - if (clk_prepare_enable(dsi->pclk)) { - DRM_DEV_ERROR(dsi->dev, "Failed to enable pclk\n"); - return; - } - - drm_panel_disable(dsi->panel); - - dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE); - drm_panel_unprepare(dsi->panel); - - dw_mipi_dsi_disable(dsi); - pm_runtime_put(dsi->dev); - clk_disable_unprepare(dsi->pclk); - dsi->dpms_mode = DRM_MODE_DPMS_OFF; -} - -static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) -{ - struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder); - struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode; - const struct dw_mipi_dsi_plat_data *pdata = dsi->pdata; - int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder); - u32 val; - int ret; - - ret = dw_mipi_dsi_get_lane_bps(dsi, mode); - if (ret < 0) - return; - - if (dsi->dpms_mode == DRM_MODE_DPMS_ON) - return; - - if (clk_prepare_enable(dsi->pclk)) { - DRM_DEV_ERROR(dsi->dev, "Failed to enable pclk\n"); - return; - } - - pm_runtime_get_sync(dsi->dev); - dw_mipi_dsi_init(dsi); - dw_mipi_dsi_dpi_config(dsi, mode); - dw_mipi_dsi_packet_handler_config(dsi); - dw_mipi_dsi_video_mode_config(dsi); - dw_mipi_dsi_video_packet_config(dsi, mode); - dw_mipi_dsi_command_mode_config(dsi); - dw_mipi_dsi_line_timer_config(dsi, mode); - dw_mipi_dsi_vertical_timing_config(dsi, mode); - dw_mipi_dsi_dphy_timing_config(dsi); - dw_mipi_dsi_dphy_interface_config(dsi); - dw_mipi_dsi_clear_err(dsi); - - /* - * For the RK3399, the clk of grf must be enabled before writing grf - * register. And for RK3288 or other soc, this grf_clk must be NULL, - * the clk_prepare_enable return true directly. - */ - ret = clk_prepare_enable(dsi->grf_clk); - if (ret) { - DRM_DEV_ERROR(dsi->dev, "Failed to enable grf_clk: %d\n", ret); - return; - } - - if (pdata->grf_dsi0_mode_reg) - regmap_write(dsi->grf_regmap, pdata->grf_dsi0_mode_reg, - pdata->grf_dsi0_mode); - - dw_mipi_dsi_phy_init(dsi); - dw_mipi_dsi_wait_for_two_frames(mode); - - dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE); - if (drm_panel_prepare(dsi->panel)) - DRM_DEV_ERROR(dsi->dev, "failed to prepare panel\n"); - - dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE); - drm_panel_enable(dsi->panel); - - clk_disable_unprepare(dsi->pclk); - - if (mux) - val = pdata->dsi0_en_bit | (pdata->dsi0_en_bit << 16); - else - val = pdata->dsi0_en_bit << 16; - - regmap_write(dsi->grf_regmap, pdata->grf_switch_reg, val); - DRM_DEV_DEBUG(dsi->dev, - "vop %s output to dsi0\n", (mux) ? "LIT" : "BIG"); - dsi->dpms_mode = DRM_MODE_DPMS_ON; - - clk_disable_unprepare(dsi->grf_clk); -} - -static int -dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder, - struct drm_crtc_state *crtc_state, - struct drm_connector_state *conn_state) -{ - struct rockchip_crtc_state *s = to_rockchip_crtc_state(crtc_state); - struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder); - - switch (dsi->format) { - case MIPI_DSI_FMT_RGB888: - s->output_mode = ROCKCHIP_OUT_MODE_P888; - break; - case MIPI_DSI_FMT_RGB666: - s->output_mode = ROCKCHIP_OUT_MODE_P666; - break; - case MIPI_DSI_FMT_RGB565: - s->output_mode = ROCKCHIP_OUT_MODE_P565; - break; - default: - WARN_ON(1); - return -EINVAL; - } - - s->output_type = DRM_MODE_CONNECTOR_DSI; - - return 0; -} - -static const struct drm_encoder_helper_funcs -dw_mipi_dsi_encoder_helper_funcs = { - .enable = dw_mipi_dsi_encoder_enable, - .disable = dw_mipi_dsi_encoder_disable, - .atomic_check = dw_mipi_dsi_encoder_atomic_check, -}; - -static const struct drm_encoder_funcs dw_mipi_dsi_encoder_funcs = { - .destroy = drm_encoder_cleanup, -}; - -static int dw_mipi_dsi_connector_get_modes(struct drm_connector *connector) -{ - struct dw_mipi_dsi *dsi = con_to_dsi(connector); - - return drm_panel_get_modes(dsi->panel); -} - -static struct drm_connector_helper_funcs dw_mipi_dsi_connector_helper_funcs = { - .get_modes = dw_mipi_dsi_connector_get_modes, -}; - -static void dw_mipi_dsi_drm_connector_destroy(struct drm_connector *connector) -{ - drm_connector_unregister(connector); - drm_connector_cleanup(connector); -} - -static const struct drm_connector_funcs dw_mipi_dsi_atomic_connector_funcs = { - .fill_modes = drm_helper_probe_single_connector_modes, - .destroy = dw_mipi_dsi_drm_connector_destroy, - .reset = drm_atomic_helper_connector_reset, - .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, - .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, -}; - -static int dw_mipi_dsi_register(struct drm_device *drm, - struct dw_mipi_dsi *dsi) -{ - struct drm_encoder *encoder = &dsi->encoder; - struct drm_connector *connector = &dsi->connector; - struct device *dev = dsi->dev; - int ret; - - encoder->possible_crtcs = drm_of_find_possible_crtcs(drm, - dev->of_node); - /* - * If we failed to find the CRTC(s) which this encoder is - * supposed to be connected to, it's because the CRTC has - * not been registered yet. Defer probing, and hope that - * the required CRTC is added later. - */ - if (encoder->possible_crtcs == 0) - return -EPROBE_DEFER; - - drm_encoder_helper_add(&dsi->encoder, - &dw_mipi_dsi_encoder_helper_funcs); - ret = drm_encoder_init(drm, &dsi->encoder, &dw_mipi_dsi_encoder_funcs, - DRM_MODE_ENCODER_DSI, NULL); - if (ret) { - DRM_DEV_ERROR(dev, "Failed to initialize encoder with drm\n"); - return ret; - } - - drm_connector_helper_add(connector, - &dw_mipi_dsi_connector_helper_funcs); - - drm_connector_init(drm, &dsi->connector, - &dw_mipi_dsi_atomic_connector_funcs, - DRM_MODE_CONNECTOR_DSI); - - drm_connector_attach_encoder(connector, encoder); - - return 0; -} - -static int rockchip_mipi_parse_dt(struct dw_mipi_dsi *dsi) -{ - struct device_node *np = dsi->dev->of_node; - - dsi->grf_regmap = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); - if (IS_ERR(dsi->grf_regmap)) { - DRM_DEV_ERROR(dsi->dev, "Unable to get rockchip,grf\n"); - return PTR_ERR(dsi->grf_regmap); - } - - return 0; -} - -static struct dw_mipi_dsi_plat_data rk3288_mipi_dsi_drv_data = { - .dsi0_en_bit = RK3288_DSI0_SEL_VOP_LIT, - .dsi1_en_bit = RK3288_DSI1_SEL_VOP_LIT, - .grf_switch_reg = RK3288_GRF_SOC_CON6, - .max_data_lanes = 4, -}; - -static struct dw_mipi_dsi_plat_data rk3399_mipi_dsi_drv_data = { - .dsi0_en_bit = RK3399_DSI0_SEL_VOP_LIT, - .dsi1_en_bit = RK3399_DSI1_SEL_VOP_LIT, - .grf_switch_reg = RK3399_GRF_SOC_CON20, - .grf_dsi0_mode = RK3399_GRF_DSI_MODE, - .grf_dsi0_mode_reg = RK3399_GRF_SOC_CON22, - .flags = DW_MIPI_NEEDS_PHY_CFG_CLK | DW_MIPI_NEEDS_GRF_CLK, - .max_data_lanes = 4, -}; - -static const struct of_device_id dw_mipi_dsi_dt_ids[] = { - { - .compatible = "rockchip,rk3288-mipi-dsi", - .data = &rk3288_mipi_dsi_drv_data, - }, { - .compatible = "rockchip,rk3399-mipi-dsi", - .data = &rk3399_mipi_dsi_drv_data, - }, - { /* sentinel */ } -}; -MODULE_DEVICE_TABLE(of, dw_mipi_dsi_dt_ids); - -static int dw_mipi_dsi_bind(struct device *dev, struct device *master, - void *data) -{ - const struct of_device_id *of_id = - of_match_device(dw_mipi_dsi_dt_ids, dev); - const struct dw_mipi_dsi_plat_data *pdata = of_id->data; - struct platform_device *pdev = to_platform_device(dev); - struct reset_control *apb_rst; - struct drm_device *drm = data; - struct dw_mipi_dsi *dsi; - struct resource *res; - int ret; - - dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL); - if (!dsi) - return -ENOMEM; - - dsi->dev = dev; - dsi->pdata = pdata; - dsi->dpms_mode = DRM_MODE_DPMS_OFF; - - ret = rockchip_mipi_parse_dt(dsi); - if (ret) - return ret; - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - dsi->base = devm_ioremap_resource(dev, res); - if (IS_ERR(dsi->base)) - return PTR_ERR(dsi->base); - - dsi->pllref_clk = devm_clk_get(dev, "ref"); - if (IS_ERR(dsi->pllref_clk)) { - ret = PTR_ERR(dsi->pllref_clk); - DRM_DEV_ERROR(dev, - "Unable to get pll reference clock: %d\n", ret); - return ret; - } - - dsi->pclk = devm_clk_get(dev, "pclk"); - if (IS_ERR(dsi->pclk)) { - ret = PTR_ERR(dsi->pclk); - DRM_DEV_ERROR(dev, "Unable to get pclk: %d\n", ret); - return ret; - } - - /* - * Note that the reset was not defined in the initial device tree, so - * we have to be prepared for it not being found. - */ - apb_rst = devm_reset_control_get(dev, "apb"); - if (IS_ERR(apb_rst)) { - ret = PTR_ERR(apb_rst); - if (ret == -ENOENT) { - apb_rst = NULL; - } else { - DRM_DEV_ERROR(dev, - "Unable to get reset control: %d\n", ret); - return ret; - } - } - - if (apb_rst) { - ret = clk_prepare_enable(dsi->pclk); - if (ret) { - DRM_DEV_ERROR(dev, "Failed to enable pclk\n"); - return ret; - } - - reset_control_assert(apb_rst); - usleep_range(10, 20); - reset_control_deassert(apb_rst); - - clk_disable_unprepare(dsi->pclk); - } - - if (pdata->flags & DW_MIPI_NEEDS_PHY_CFG_CLK) { - dsi->phy_cfg_clk = devm_clk_get(dev, "phy_cfg"); - if (IS_ERR(dsi->phy_cfg_clk)) { - ret = PTR_ERR(dsi->phy_cfg_clk); - DRM_DEV_ERROR(dev, - "Unable to get phy_cfg_clk: %d\n", ret); - return ret; - } - } - - if (pdata->flags & DW_MIPI_NEEDS_GRF_CLK) { - dsi->grf_clk = devm_clk_get(dev, "grf"); - if (IS_ERR(dsi->grf_clk)) { - ret = PTR_ERR(dsi->grf_clk); - DRM_DEV_ERROR(dev, "Unable to get grf_clk: %d\n", ret); - return ret; - } - } - - ret = clk_prepare_enable(dsi->pllref_clk); - if (ret) { - DRM_DEV_ERROR(dev, "Failed to enable pllref_clk\n"); - return ret; - } - - ret = dw_mipi_dsi_register(drm, dsi); - if (ret) { - DRM_DEV_ERROR(dev, "Failed to register mipi_dsi: %d\n", ret); - goto err_pllref; - } - - dsi->dsi_host.ops = &dw_mipi_dsi_host_ops; - dsi->dsi_host.dev = dev; - ret = mipi_dsi_host_register(&dsi->dsi_host); - if (ret) { - DRM_DEV_ERROR(dev, "Failed to register MIPI host: %d\n", ret); - goto err_cleanup; - } - - if (!dsi->panel) { - ret = -EPROBE_DEFER; - goto err_mipi_dsi_host; - } - - dev_set_drvdata(dev, dsi); - pm_runtime_enable(dev); - return 0; - -err_mipi_dsi_host: - mipi_dsi_host_unregister(&dsi->dsi_host); -err_cleanup: - dsi->connector.funcs->destroy(&dsi->connector); - dsi->encoder.funcs->destroy(&dsi->encoder); -err_pllref: - clk_disable_unprepare(dsi->pllref_clk); - return ret; -} - -static void dw_mipi_dsi_unbind(struct device *dev, struct device *master, - void *data) -{ - struct dw_mipi_dsi *dsi = dev_get_drvdata(dev); - - mipi_dsi_host_unregister(&dsi->dsi_host); - pm_runtime_disable(dev); - - dsi->connector.funcs->destroy(&dsi->connector); - dsi->encoder.funcs->destroy(&dsi->encoder); - - clk_disable_unprepare(dsi->pllref_clk); -} - -static const struct component_ops dw_mipi_dsi_ops = { - .bind = dw_mipi_dsi_bind, - .unbind = dw_mipi_dsi_unbind, -}; - -static int dw_mipi_dsi_probe(struct platform_device *pdev) -{ - return component_add(&pdev->dev, &dw_mipi_dsi_ops); -} - -static int dw_mipi_dsi_remove(struct platform_device *pdev) -{ - component_del(&pdev->dev, &dw_mipi_dsi_ops); - return 0; -} - -struct platform_driver dw_mipi_dsi_driver = { - .probe = dw_mipi_dsi_probe, - .remove = dw_mipi_dsi_remove, - .driver = { - .of_match_table = dw_mipi_dsi_dt_ids, - .name = DRIVER_NAME, - }, -}; diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.c b/drivers/gpu/drm/rockchip/rockchip_drm_drv.c index 941f35233b1f..37f9a3b651ab 100644 --- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.c +++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.c @@ -489,7 +489,7 @@ static int __init rockchip_drm_init(void) ADD_ROCKCHIP_SUB_DRIVER(cdn_dp_driver, CONFIG_ROCKCHIP_CDN_DP); ADD_ROCKCHIP_SUB_DRIVER(dw_hdmi_rockchip_pltfm_driver, CONFIG_ROCKCHIP_DW_HDMI); - ADD_ROCKCHIP_SUB_DRIVER(dw_mipi_dsi_driver, + ADD_ROCKCHIP_SUB_DRIVER(dw_mipi_dsi_rockchip_driver, CONFIG_ROCKCHIP_DW_MIPI_DSI); ADD_ROCKCHIP_SUB_DRIVER(inno_hdmi_driver, CONFIG_ROCKCHIP_INNO_HDMI); diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h index 21a023a97bb8..453fef6a55b9 100644 --- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h +++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h @@ -67,7 +67,7 @@ int rockchip_drm_wait_vact_end(struct drm_crtc *crtc, unsigned int mstimeout); int rockchip_drm_endpoint_is_subdriver(struct device_node *ep); extern struct platform_driver cdn_dp_driver; extern struct platform_driver dw_hdmi_rockchip_pltfm_driver; -extern struct platform_driver dw_mipi_dsi_driver; +extern struct platform_driver dw_mipi_dsi_rockchip_driver; extern struct platform_driver inno_hdmi_driver; extern struct platform_driver rockchip_dp_driver; extern struct platform_driver rockchip_lvds_driver; -- 2.18.0 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 6/7] drm/bridge/synopsys: dsi: add dual-dsi support 2018-10-01 12:38 ` Heiko Stuebner @ 2018-10-01 12:38 ` Heiko Stuebner -1 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: architt, hjc, a.hajda Cc: briannorris, hoegsberg, philippe.cornu, dri-devel, yannick.fertre, linux-rockchip, nickey.yang, mka, seanpaul, linux-arm-kernel From: Nickey Yang <nickey.yang@rock-chips.com> Allow to also drive a slave dw-mipi-dsi controller in a dual-dsi setup. This will require additional implementation-specific code to look up the slave instance and do specific setup. Also will probably need code in the specific crtcs as dual-dsi does not equal two separate dsi outputs. To activate, the implementation-specific code should set the slave using dw_mipi_dsi_set_slave() before calling __dw_mipi_dsi_bind(). v2: - expect real interface number of lanes - keep links to both master and slave v3: - remove unneeded separate variables - remove unneeded second slave settings - disable slave before master - lane-sum calculation comments Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> --- drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 80 +++++++++++++++++-- include/drm/bridge/dw_mipi_dsi.h | 1 + 2 files changed, 75 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c index 3962e5d84e1e..2f4b145b73af 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c @@ -230,9 +230,20 @@ struct dw_mipi_dsi { u32 format; unsigned long mode_flags; + struct dw_mipi_dsi *master; /* dual-dsi master ptr */ + struct dw_mipi_dsi *slave; /* dual-dsi slave ptr */ + const struct dw_mipi_dsi_plat_data *plat_data; }; +/* + * Check if either a link to a master or slave is present + */ +static inline bool dw_mipi_is_dual_mode(struct dw_mipi_dsi *dsi) +{ + return dsi->slave || dsi->master; +} + /* * The controller should generate 2 frames before * preparing the peripheral. @@ -456,10 +467,17 @@ static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host, } dw_mipi_message_config(dsi, msg); + if (dsi->slave) + dw_mipi_message_config(dsi->slave, msg); ret = dw_mipi_dsi_write(dsi, &packet); if (ret) return ret; + if (dsi->slave) { + ret = dw_mipi_dsi_write(dsi->slave, &packet); + if (ret) + return ret; + } if (msg->rx_buf && msg->rx_len) { ret = dw_mipi_dsi_read(dsi, msg); @@ -598,7 +616,11 @@ static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi, * DSI_VNPCR.NPSIZE... especially because this driver supports * non-burst video modes, see dw_mipi_dsi_video_mode_config()... */ - dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay)); + + dsi_write(dsi, DSI_VID_PKT_SIZE, + dw_mipi_is_dual_mode(dsi) ? + VID_PKT_SIZE(mode->hdisplay / 2) : + VID_PKT_SIZE(mode->hdisplay)); } static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi) @@ -770,24 +792,43 @@ static void dw_mipi_dsi_bridge_post_disable(struct drm_bridge *bridge) */ dsi->panel_bridge->funcs->post_disable(dsi->panel_bridge); + if (dsi->slave) { + dw_mipi_dsi_disable(dsi->slave); + clk_disable_unprepare(dsi->slave->pclk); + pm_runtime_put(dsi->slave->dev); + } dw_mipi_dsi_disable(dsi); + clk_disable_unprepare(dsi->pclk); pm_runtime_put(dsi->dev); } -static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge, - struct drm_display_mode *mode, - struct drm_display_mode *adjusted_mode) +static unsigned int dw_mipi_dsi_get_lanes(struct dw_mipi_dsi *dsi) +{ + /* this instance is the slave, so add the master's lanes */ + if (dsi->master) + return dsi->master->lanes + dsi->lanes; + + /* this instance is the master, so add the slave's lanes */ + if (dsi->slave) + return dsi->lanes + dsi->slave->lanes; + + /* single-dsi, so no other instance to consider */ + return dsi->lanes; +} + +static void dw_mipi_dsi_mode_set(struct dw_mipi_dsi *dsi, + struct drm_display_mode *adjusted_mode) { - struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops; void *priv_data = dsi->plat_data->priv_data; int ret; + u32 lanes = dw_mipi_dsi_get_lanes(dsi); clk_prepare_enable(dsi->pclk); ret = phy_ops->get_lane_mbps(priv_data, adjusted_mode, dsi->mode_flags, - dsi->lanes, dsi->format, &dsi->lane_mbps); + lanes, dsi->format, &dsi->lane_mbps); if (ret) DRM_DEBUG_DRIVER("Phy get_lane_mbps() failed\n"); @@ -819,12 +860,25 @@ static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge, dw_mipi_dsi_set_mode(dsi, 0); } +static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); + + dw_mipi_dsi_mode_set(dsi, adjusted_mode); + if (dsi->slave) + dw_mipi_dsi_mode_set(dsi->slave, adjusted_mode); +} + static void dw_mipi_dsi_bridge_enable(struct drm_bridge *bridge) { struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); /* Switch to video mode for panel-bridge enable & panel enable */ dw_mipi_dsi_set_mode(dsi, MIPI_DSI_MODE_VIDEO); + if (dsi->slave) + dw_mipi_dsi_set_mode(dsi->slave, MIPI_DSI_MODE_VIDEO); } static enum drm_mode_status @@ -961,6 +1015,20 @@ static void __dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi) pm_runtime_disable(dsi->dev); } +void dw_mipi_dsi_set_slave(struct dw_mipi_dsi *dsi, struct dw_mipi_dsi *slave) +{ + /* introduce controllers to each other */ + dsi->slave = slave; + dsi->slave->master = dsi; + + /* migrate settings for already attached displays */ + dsi->slave->lanes = dsi->lanes; + dsi->slave->channel = dsi->channel; + dsi->slave->format = dsi->format; + dsi->slave->mode_flags = dsi->mode_flags; +} +EXPORT_SYMBOL_GPL(dw_mipi_dsi_set_slave); + /* * Probe/remove API, used from platforms based on the DRM bridge API. */ diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h index a9c03099cf3e..48a671e782ca 100644 --- a/include/drm/bridge/dw_mipi_dsi.h +++ b/include/drm/bridge/dw_mipi_dsi.h @@ -45,5 +45,6 @@ struct dw_mipi_dsi *dw_mipi_dsi_probe(struct platform_device *pdev, void dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi); int dw_mipi_dsi_bind(struct dw_mipi_dsi *dsi, struct drm_encoder *encoder); void dw_mipi_dsi_unbind(struct dw_mipi_dsi *dsi); +void dw_mipi_dsi_set_slave(struct dw_mipi_dsi *dsi, struct dw_mipi_dsi *slave); #endif /* __DW_MIPI_DSI__ */ -- 2.18.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 6/7] drm/bridge/synopsys: dsi: add dual-dsi support @ 2018-10-01 12:38 ` Heiko Stuebner 0 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: linux-arm-kernel From: Nickey Yang <nickey.yang@rock-chips.com> Allow to also drive a slave dw-mipi-dsi controller in a dual-dsi setup. This will require additional implementation-specific code to look up the slave instance and do specific setup. Also will probably need code in the specific crtcs as dual-dsi does not equal two separate dsi outputs. To activate, the implementation-specific code should set the slave using dw_mipi_dsi_set_slave() before calling __dw_mipi_dsi_bind(). v2: - expect real interface number of lanes - keep links to both master and slave v3: - remove unneeded separate variables - remove unneeded second slave settings - disable slave before master - lane-sum calculation comments Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> --- drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 80 +++++++++++++++++-- include/drm/bridge/dw_mipi_dsi.h | 1 + 2 files changed, 75 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c index 3962e5d84e1e..2f4b145b73af 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c @@ -230,9 +230,20 @@ struct dw_mipi_dsi { u32 format; unsigned long mode_flags; + struct dw_mipi_dsi *master; /* dual-dsi master ptr */ + struct dw_mipi_dsi *slave; /* dual-dsi slave ptr */ + const struct dw_mipi_dsi_plat_data *plat_data; }; +/* + * Check if either a link to a master or slave is present + */ +static inline bool dw_mipi_is_dual_mode(struct dw_mipi_dsi *dsi) +{ + return dsi->slave || dsi->master; +} + /* * The controller should generate 2 frames before * preparing the peripheral. @@ -456,10 +467,17 @@ static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host, } dw_mipi_message_config(dsi, msg); + if (dsi->slave) + dw_mipi_message_config(dsi->slave, msg); ret = dw_mipi_dsi_write(dsi, &packet); if (ret) return ret; + if (dsi->slave) { + ret = dw_mipi_dsi_write(dsi->slave, &packet); + if (ret) + return ret; + } if (msg->rx_buf && msg->rx_len) { ret = dw_mipi_dsi_read(dsi, msg); @@ -598,7 +616,11 @@ static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi, * DSI_VNPCR.NPSIZE... especially because this driver supports * non-burst video modes, see dw_mipi_dsi_video_mode_config()... */ - dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay)); + + dsi_write(dsi, DSI_VID_PKT_SIZE, + dw_mipi_is_dual_mode(dsi) ? + VID_PKT_SIZE(mode->hdisplay / 2) : + VID_PKT_SIZE(mode->hdisplay)); } static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi) @@ -770,24 +792,43 @@ static void dw_mipi_dsi_bridge_post_disable(struct drm_bridge *bridge) */ dsi->panel_bridge->funcs->post_disable(dsi->panel_bridge); + if (dsi->slave) { + dw_mipi_dsi_disable(dsi->slave); + clk_disable_unprepare(dsi->slave->pclk); + pm_runtime_put(dsi->slave->dev); + } dw_mipi_dsi_disable(dsi); + clk_disable_unprepare(dsi->pclk); pm_runtime_put(dsi->dev); } -static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge, - struct drm_display_mode *mode, - struct drm_display_mode *adjusted_mode) +static unsigned int dw_mipi_dsi_get_lanes(struct dw_mipi_dsi *dsi) +{ + /* this instance is the slave, so add the master's lanes */ + if (dsi->master) + return dsi->master->lanes + dsi->lanes; + + /* this instance is the master, so add the slave's lanes */ + if (dsi->slave) + return dsi->lanes + dsi->slave->lanes; + + /* single-dsi, so no other instance to consider */ + return dsi->lanes; +} + +static void dw_mipi_dsi_mode_set(struct dw_mipi_dsi *dsi, + struct drm_display_mode *adjusted_mode) { - struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops; void *priv_data = dsi->plat_data->priv_data; int ret; + u32 lanes = dw_mipi_dsi_get_lanes(dsi); clk_prepare_enable(dsi->pclk); ret = phy_ops->get_lane_mbps(priv_data, adjusted_mode, dsi->mode_flags, - dsi->lanes, dsi->format, &dsi->lane_mbps); + lanes, dsi->format, &dsi->lane_mbps); if (ret) DRM_DEBUG_DRIVER("Phy get_lane_mbps() failed\n"); @@ -819,12 +860,25 @@ static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge, dw_mipi_dsi_set_mode(dsi, 0); } +static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); + + dw_mipi_dsi_mode_set(dsi, adjusted_mode); + if (dsi->slave) + dw_mipi_dsi_mode_set(dsi->slave, adjusted_mode); +} + static void dw_mipi_dsi_bridge_enable(struct drm_bridge *bridge) { struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); /* Switch to video mode for panel-bridge enable & panel enable */ dw_mipi_dsi_set_mode(dsi, MIPI_DSI_MODE_VIDEO); + if (dsi->slave) + dw_mipi_dsi_set_mode(dsi->slave, MIPI_DSI_MODE_VIDEO); } static enum drm_mode_status @@ -961,6 +1015,20 @@ static void __dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi) pm_runtime_disable(dsi->dev); } +void dw_mipi_dsi_set_slave(struct dw_mipi_dsi *dsi, struct dw_mipi_dsi *slave) +{ + /* introduce controllers to each other */ + dsi->slave = slave; + dsi->slave->master = dsi; + + /* migrate settings for already attached displays */ + dsi->slave->lanes = dsi->lanes; + dsi->slave->channel = dsi->channel; + dsi->slave->format = dsi->format; + dsi->slave->mode_flags = dsi->mode_flags; +} +EXPORT_SYMBOL_GPL(dw_mipi_dsi_set_slave); + /* * Probe/remove API, used from platforms based on the DRM bridge API. */ diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h index a9c03099cf3e..48a671e782ca 100644 --- a/include/drm/bridge/dw_mipi_dsi.h +++ b/include/drm/bridge/dw_mipi_dsi.h @@ -45,5 +45,6 @@ struct dw_mipi_dsi *dw_mipi_dsi_probe(struct platform_device *pdev, void dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi); int dw_mipi_dsi_bind(struct dw_mipi_dsi *dsi, struct drm_encoder *encoder); void dw_mipi_dsi_unbind(struct dw_mipi_dsi *dsi); +void dw_mipi_dsi_set_slave(struct dw_mipi_dsi *dsi, struct dw_mipi_dsi *slave); #endif /* __DW_MIPI_DSI__ */ -- 2.18.0 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 7/7] drm/rockchip: dsi: add dual mipi support 2018-10-01 12:38 ` Heiko Stuebner @ 2018-10-01 12:38 ` Heiko Stuebner -1 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: architt, hjc, a.hajda Cc: briannorris, hoegsberg, philippe.cornu, dri-devel, yannick.fertre, linux-rockchip, nickey.yang, mka, seanpaul, linux-arm-kernel Add the Rockchip-sepcific dual-dsi setup and hook it into the VOP as well. As described in the general dual-dsi devicetree binding, the panel should define two input ports and point each of them to one of the used dsi- controllers, as well as declare one of them as clock-master. This is used to determine the dual-dsi state and get access to both controller instances. v6: handle master+slave component in dsi-attach v5: use driver-internal mechanism to find dual dsi slave v4: add component directly in probe when adding empty dsi slave controller Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- .../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 136 ++++++++++++++++++ drivers/gpu/drm/rockchip/rockchip_drm_drv.h | 1 + drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 3 + drivers/gpu/drm/rockchip/rockchip_drm_vop.h | 4 + drivers/gpu/drm/rockchip/rockchip_vop_reg.c | 1 + 5 files changed, 145 insertions(+) diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c index b3aae8439aa3..63b028602d08 100644 --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c @@ -218,6 +218,10 @@ struct dw_mipi_dsi_rockchip { struct clk *grf_clk; struct clk *phy_cfg_clk; + /* dual-channel */ + bool is_slave; + struct dw_mipi_dsi_rockchip *slave; + unsigned int lane_mbps; /* per lane */ u16 input_div; u16 feedback_div; @@ -226,6 +230,7 @@ struct dw_mipi_dsi_rockchip { struct dw_mipi_dsi *dmd; const struct rockchip_dw_dsi_chip_data *cdata; struct dw_mipi_dsi_plat_data pdata; + int devcnt; }; struct dphy_pll_parameter_map { @@ -602,6 +607,8 @@ dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder, } s->output_type = DRM_MODE_CONNECTOR_DSI; + if (dsi->slave) + s->output_flags = ROCKCHIP_OUTPUT_DSI_DUAL; return 0; } @@ -617,6 +624,8 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) return; pm_runtime_get_sync(dsi->dev); + if (dsi->slave) + pm_runtime_get_sync(dsi->slave->dev); /* * For the RK3399, the clk of grf must be enabled before writing grf @@ -630,6 +639,8 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) } dw_mipi_dsi_rockchip_config(dsi, mux); + if (dsi->slave) + dw_mipi_dsi_rockchip_config(dsi->slave, mux); clk_disable_unprepare(dsi->grf_clk); } @@ -638,6 +649,8 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) { struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); + if (dsi->slave) + pm_runtime_put(dsi->slave->dev); pm_runtime_put(dsi->dev); } @@ -673,14 +686,113 @@ static int rockchip_dsi_drm_create_encoder(struct dw_mipi_dsi_rockchip *dsi, return 0; } +static struct device +*dw_mipi_dsi_rockchip_find_second(struct dw_mipi_dsi_rockchip *dsi) +{ + const struct of_device_id *match; + struct device_node *node = NULL, *local; + + match = of_match_device(dsi->dev->driver->of_match_table, dsi->dev); + + local = of_graph_get_remote_node(dsi->dev->of_node, 1, 0); + if (!local) + return NULL; + + while ((node = of_find_compatible_node(node, NULL, + match->compatible))) { + struct device_node *remote; + + /* found ourself */ + if (node == dsi->dev->of_node) + continue; + + remote = of_graph_get_remote_node(node, 1, 0); + if (!remote) + continue; + + /* same display device in port1-ep0 for both */ + if (remote == local) { + struct dw_mipi_dsi_rockchip *dsi2; + struct platform_device *pdev; + + pdev = of_find_device_by_node(node); + + /* + * we have found the second, so will either return it + * or return with an error. In any case won't need the + * nodes anymore nor continue the loop. + */ + of_node_put(remote); + of_node_put(node); + of_node_put(local); + + if (!pdev) + return ERR_PTR(-EPROBE_DEFER); + + dsi2 = platform_get_drvdata(pdev); + if (!dsi2) { + platform_device_put(pdev); + return ERR_PTR(-EPROBE_DEFER); + } + + return &pdev->dev; + } + + of_node_put(remote); + } + + of_node_put(local); + + return NULL; +} + static int dw_mipi_dsi_rockchip_bind(struct device *dev, struct device *master, void *data) { struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); struct drm_device *drm_dev = data; + struct device *second; + bool master1, master2; int ret; + second = dw_mipi_dsi_rockchip_find_second(dsi); + if (IS_ERR(second)) + return PTR_ERR(second); + + if (second) { + master1 = of_property_read_bool(dsi->dev->of_node, + "clock-master"); + master2 = of_property_read_bool(second->of_node, + "clock-master"); + + if (master1 && master2) { + DRM_DEV_ERROR(dsi->dev, "only one clock-master allowed\n"); + return -EINVAL; + } + + if (!master1 && !master2) { + DRM_DEV_ERROR(dsi->dev, "no clock-master defined\n"); + return -EINVAL; + } + + /* we are the slave in dual-DSI */ + if (!master1) { + dsi->is_slave = true; + return 0; + } + + dsi->slave = dev_get_drvdata(second); + if (!dsi->slave) { + DRM_DEV_ERROR(dev, "could not get slaves data\n"); + return -ENODEV; + } + + dsi->slave->is_slave = true; + dw_mipi_dsi_set_slave(dsi->dmd, dsi->slave->dmd); + put_device(second); + } + ret = clk_prepare_enable(dsi->pllref_clk); if (ret) { DRM_DEV_ERROR(dev, "Failed to enable pllref_clk: %d\n", ret); @@ -708,6 +819,9 @@ static void dw_mipi_dsi_rockchip_unbind(struct device *dev, { struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); + if (dsi->is_slave) + return; + dw_mipi_dsi_unbind(dsi->dmd); clk_disable_unprepare(dsi->pllref_clk); @@ -722,6 +836,7 @@ static int dw_mipi_dsi_rockchip_host_attach(void *priv_data, struct mipi_dsi_device *device) { struct dw_mipi_dsi_rockchip *dsi = priv_data; + struct device *second; int ret; ret = component_add(dsi->dev, &dw_mipi_dsi_rockchip_ops); @@ -731,6 +846,19 @@ static int dw_mipi_dsi_rockchip_host_attach(void *priv_data, return ret; } + second = dw_mipi_dsi_rockchip_find_second(dsi); + if (IS_ERR(second)) + return PTR_ERR(second); + if (second) { + ret = component_add(second, &dw_mipi_dsi_rockchip_ops); + if (ret) { + DRM_DEV_ERROR(second, + "Failed to register component: %d\n", + ret); + return ret; + } + } + return 0; } @@ -738,6 +866,11 @@ static int dw_mipi_dsi_rockchip_host_detach(void *priv_data, struct mipi_dsi_device *device) { struct dw_mipi_dsi_rockchip *dsi = priv_data; + struct device *second; + + second = dw_mipi_dsi_rockchip_find_second(dsi); + if (second && !IS_ERR(second)) + component_del(second, &dw_mipi_dsi_rockchip_ops); component_del(dsi->dev, &dw_mipi_dsi_rockchip_ops); @@ -846,6 +979,9 @@ static int dw_mipi_dsi_rockchip_remove(struct platform_device *pdev) { struct dw_mipi_dsi_rockchip *dsi = platform_get_drvdata(pdev); + if (dsi->devcnt == 0) + component_del(dsi->dev, &dw_mipi_dsi_rockchip_ops); + dw_mipi_dsi_remove(dsi->dmd); return 0; diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h index 453fef6a55b9..ce48568ec8a0 100644 --- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h +++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h @@ -37,6 +37,7 @@ struct rockchip_crtc_state { int output_type; int output_mode; int output_bpc; + int output_flags; }; #define to_rockchip_crtc_state(s) \ container_of(s, struct rockchip_crtc_state, base) diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c index 0c35a88e33dd..fb70fb486fbf 100644 --- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c +++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c @@ -916,6 +916,7 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc, pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC) ? BIT(VSYNC_POSITIVE) : 0; VOP_REG_SET(vop, output, pin_pol, pin_pol); + VOP_REG_SET(vop, output, mipi_dual_channel_en, 0); switch (s->output_type) { case DRM_MODE_CONNECTOR_LVDS: @@ -933,6 +934,8 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc, case DRM_MODE_CONNECTOR_DSI: VOP_REG_SET(vop, output, mipi_pin_pol, pin_pol); VOP_REG_SET(vop, output, mipi_en, 1); + VOP_REG_SET(vop, output, mipi_dual_channel_en, + !!(s->output_flags & ROCKCHIP_OUTPUT_DSI_DUAL)); break; case DRM_MODE_CONNECTOR_DisplayPort: pin_pol &= ~BIT(DCLK_INVERT); diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.h b/drivers/gpu/drm/rockchip/rockchip_drm_vop.h index fd5765dfd637..0fe40e1983d9 100644 --- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.h +++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.h @@ -60,6 +60,7 @@ struct vop_output { struct vop_reg edp_en; struct vop_reg hdmi_en; struct vop_reg mipi_en; + struct vop_reg mipi_dual_channel_en; struct vop_reg rgb_en; }; @@ -214,6 +215,9 @@ struct vop_data { /* for use special outface */ #define ROCKCHIP_OUT_MODE_AAAA 15 +/* output flags */ +#define ROCKCHIP_OUTPUT_DSI_DUAL BIT(0) + enum alpha_mode { ALPHA_STRAIGHT, ALPHA_INVERSE, diff --git a/drivers/gpu/drm/rockchip/rockchip_vop_reg.c b/drivers/gpu/drm/rockchip/rockchip_vop_reg.c index 047a8867af90..08fc40af52c8 100644 --- a/drivers/gpu/drm/rockchip/rockchip_vop_reg.c +++ b/drivers/gpu/drm/rockchip/rockchip_vop_reg.c @@ -634,6 +634,7 @@ static const struct vop_output rk3399_output = { .hdmi_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 13), .edp_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 14), .mipi_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 15), + .mipi_dual_channel_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 3), }; static const struct vop_data rk3399_vop_big = { -- 2.18.0 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v6 7/7] drm/rockchip: dsi: add dual mipi support @ 2018-10-01 12:38 ` Heiko Stuebner 0 siblings, 0 replies; 20+ messages in thread From: Heiko Stuebner @ 2018-10-01 12:38 UTC (permalink / raw) To: linux-arm-kernel Add the Rockchip-sepcific dual-dsi setup and hook it into the VOP as well. As described in the general dual-dsi devicetree binding, the panel should define two input ports and point each of them to one of the used dsi- controllers, as well as declare one of them as clock-master. This is used to determine the dual-dsi state and get access to both controller instances. v6: handle master+slave component in dsi-attach v5: use driver-internal mechanism to find dual dsi slave v4: add component directly in probe when adding empty dsi slave controller Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- .../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 136 ++++++++++++++++++ drivers/gpu/drm/rockchip/rockchip_drm_drv.h | 1 + drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 3 + drivers/gpu/drm/rockchip/rockchip_drm_vop.h | 4 + drivers/gpu/drm/rockchip/rockchip_vop_reg.c | 1 + 5 files changed, 145 insertions(+) diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c index b3aae8439aa3..63b028602d08 100644 --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c @@ -218,6 +218,10 @@ struct dw_mipi_dsi_rockchip { struct clk *grf_clk; struct clk *phy_cfg_clk; + /* dual-channel */ + bool is_slave; + struct dw_mipi_dsi_rockchip *slave; + unsigned int lane_mbps; /* per lane */ u16 input_div; u16 feedback_div; @@ -226,6 +230,7 @@ struct dw_mipi_dsi_rockchip { struct dw_mipi_dsi *dmd; const struct rockchip_dw_dsi_chip_data *cdata; struct dw_mipi_dsi_plat_data pdata; + int devcnt; }; struct dphy_pll_parameter_map { @@ -602,6 +607,8 @@ dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder, } s->output_type = DRM_MODE_CONNECTOR_DSI; + if (dsi->slave) + s->output_flags = ROCKCHIP_OUTPUT_DSI_DUAL; return 0; } @@ -617,6 +624,8 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) return; pm_runtime_get_sync(dsi->dev); + if (dsi->slave) + pm_runtime_get_sync(dsi->slave->dev); /* * For the RK3399, the clk of grf must be enabled before writing grf @@ -630,6 +639,8 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) } dw_mipi_dsi_rockchip_config(dsi, mux); + if (dsi->slave) + dw_mipi_dsi_rockchip_config(dsi->slave, mux); clk_disable_unprepare(dsi->grf_clk); } @@ -638,6 +649,8 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) { struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); + if (dsi->slave) + pm_runtime_put(dsi->slave->dev); pm_runtime_put(dsi->dev); } @@ -673,14 +686,113 @@ static int rockchip_dsi_drm_create_encoder(struct dw_mipi_dsi_rockchip *dsi, return 0; } +static struct device +*dw_mipi_dsi_rockchip_find_second(struct dw_mipi_dsi_rockchip *dsi) +{ + const struct of_device_id *match; + struct device_node *node = NULL, *local; + + match = of_match_device(dsi->dev->driver->of_match_table, dsi->dev); + + local = of_graph_get_remote_node(dsi->dev->of_node, 1, 0); + if (!local) + return NULL; + + while ((node = of_find_compatible_node(node, NULL, + match->compatible))) { + struct device_node *remote; + + /* found ourself */ + if (node == dsi->dev->of_node) + continue; + + remote = of_graph_get_remote_node(node, 1, 0); + if (!remote) + continue; + + /* same display device in port1-ep0 for both */ + if (remote == local) { + struct dw_mipi_dsi_rockchip *dsi2; + struct platform_device *pdev; + + pdev = of_find_device_by_node(node); + + /* + * we have found the second, so will either return it + * or return with an error. In any case won't need the + * nodes anymore nor continue the loop. + */ + of_node_put(remote); + of_node_put(node); + of_node_put(local); + + if (!pdev) + return ERR_PTR(-EPROBE_DEFER); + + dsi2 = platform_get_drvdata(pdev); + if (!dsi2) { + platform_device_put(pdev); + return ERR_PTR(-EPROBE_DEFER); + } + + return &pdev->dev; + } + + of_node_put(remote); + } + + of_node_put(local); + + return NULL; +} + static int dw_mipi_dsi_rockchip_bind(struct device *dev, struct device *master, void *data) { struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); struct drm_device *drm_dev = data; + struct device *second; + bool master1, master2; int ret; + second = dw_mipi_dsi_rockchip_find_second(dsi); + if (IS_ERR(second)) + return PTR_ERR(second); + + if (second) { + master1 = of_property_read_bool(dsi->dev->of_node, + "clock-master"); + master2 = of_property_read_bool(second->of_node, + "clock-master"); + + if (master1 && master2) { + DRM_DEV_ERROR(dsi->dev, "only one clock-master allowed\n"); + return -EINVAL; + } + + if (!master1 && !master2) { + DRM_DEV_ERROR(dsi->dev, "no clock-master defined\n"); + return -EINVAL; + } + + /* we are the slave in dual-DSI */ + if (!master1) { + dsi->is_slave = true; + return 0; + } + + dsi->slave = dev_get_drvdata(second); + if (!dsi->slave) { + DRM_DEV_ERROR(dev, "could not get slaves data\n"); + return -ENODEV; + } + + dsi->slave->is_slave = true; + dw_mipi_dsi_set_slave(dsi->dmd, dsi->slave->dmd); + put_device(second); + } + ret = clk_prepare_enable(dsi->pllref_clk); if (ret) { DRM_DEV_ERROR(dev, "Failed to enable pllref_clk: %d\n", ret); @@ -708,6 +819,9 @@ static void dw_mipi_dsi_rockchip_unbind(struct device *dev, { struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); + if (dsi->is_slave) + return; + dw_mipi_dsi_unbind(dsi->dmd); clk_disable_unprepare(dsi->pllref_clk); @@ -722,6 +836,7 @@ static int dw_mipi_dsi_rockchip_host_attach(void *priv_data, struct mipi_dsi_device *device) { struct dw_mipi_dsi_rockchip *dsi = priv_data; + struct device *second; int ret; ret = component_add(dsi->dev, &dw_mipi_dsi_rockchip_ops); @@ -731,6 +846,19 @@ static int dw_mipi_dsi_rockchip_host_attach(void *priv_data, return ret; } + second = dw_mipi_dsi_rockchip_find_second(dsi); + if (IS_ERR(second)) + return PTR_ERR(second); + if (second) { + ret = component_add(second, &dw_mipi_dsi_rockchip_ops); + if (ret) { + DRM_DEV_ERROR(second, + "Failed to register component: %d\n", + ret); + return ret; + } + } + return 0; } @@ -738,6 +866,11 @@ static int dw_mipi_dsi_rockchip_host_detach(void *priv_data, struct mipi_dsi_device *device) { struct dw_mipi_dsi_rockchip *dsi = priv_data; + struct device *second; + + second = dw_mipi_dsi_rockchip_find_second(dsi); + if (second && !IS_ERR(second)) + component_del(second, &dw_mipi_dsi_rockchip_ops); component_del(dsi->dev, &dw_mipi_dsi_rockchip_ops); @@ -846,6 +979,9 @@ static int dw_mipi_dsi_rockchip_remove(struct platform_device *pdev) { struct dw_mipi_dsi_rockchip *dsi = platform_get_drvdata(pdev); + if (dsi->devcnt == 0) + component_del(dsi->dev, &dw_mipi_dsi_rockchip_ops); + dw_mipi_dsi_remove(dsi->dmd); return 0; diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h index 453fef6a55b9..ce48568ec8a0 100644 --- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h +++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h @@ -37,6 +37,7 @@ struct rockchip_crtc_state { int output_type; int output_mode; int output_bpc; + int output_flags; }; #define to_rockchip_crtc_state(s) \ container_of(s, struct rockchip_crtc_state, base) diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c index 0c35a88e33dd..fb70fb486fbf 100644 --- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c +++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c @@ -916,6 +916,7 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc, pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC) ? BIT(VSYNC_POSITIVE) : 0; VOP_REG_SET(vop, output, pin_pol, pin_pol); + VOP_REG_SET(vop, output, mipi_dual_channel_en, 0); switch (s->output_type) { case DRM_MODE_CONNECTOR_LVDS: @@ -933,6 +934,8 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc, case DRM_MODE_CONNECTOR_DSI: VOP_REG_SET(vop, output, mipi_pin_pol, pin_pol); VOP_REG_SET(vop, output, mipi_en, 1); + VOP_REG_SET(vop, output, mipi_dual_channel_en, + !!(s->output_flags & ROCKCHIP_OUTPUT_DSI_DUAL)); break; case DRM_MODE_CONNECTOR_DisplayPort: pin_pol &= ~BIT(DCLK_INVERT); diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.h b/drivers/gpu/drm/rockchip/rockchip_drm_vop.h index fd5765dfd637..0fe40e1983d9 100644 --- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.h +++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.h @@ -60,6 +60,7 @@ struct vop_output { struct vop_reg edp_en; struct vop_reg hdmi_en; struct vop_reg mipi_en; + struct vop_reg mipi_dual_channel_en; struct vop_reg rgb_en; }; @@ -214,6 +215,9 @@ struct vop_data { /* for use special outface */ #define ROCKCHIP_OUT_MODE_AAAA 15 +/* output flags */ +#define ROCKCHIP_OUTPUT_DSI_DUAL BIT(0) + enum alpha_mode { ALPHA_STRAIGHT, ALPHA_INVERSE, diff --git a/drivers/gpu/drm/rockchip/rockchip_vop_reg.c b/drivers/gpu/drm/rockchip/rockchip_vop_reg.c index 047a8867af90..08fc40af52c8 100644 --- a/drivers/gpu/drm/rockchip/rockchip_vop_reg.c +++ b/drivers/gpu/drm/rockchip/rockchip_vop_reg.c @@ -634,6 +634,7 @@ static const struct vop_output rk3399_output = { .hdmi_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 13), .edp_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 14), .mipi_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 15), + .mipi_dual_channel_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 3), }; static const struct vop_data rk3399_vop_big = { -- 2.18.0 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH v6 7/7] drm/rockchip: dsi: add dual mipi support 2018-10-01 12:38 ` Heiko Stuebner @ 2018-10-29 14:15 ` Andrzej Hajda -1 siblings, 0 replies; 20+ messages in thread From: Andrzej Hajda @ 2018-10-29 14:15 UTC (permalink / raw) To: Heiko Stuebner, architt, hjc Cc: briannorris, hoegsberg, philippe.cornu, dri-devel, yannick.fertre, linux-rockchip, nickey.yang, mka, seanpaul, linux-arm-kernel On 01.10.2018 14:38, Heiko Stuebner wrote: > Add the Rockchip-sepcific dual-dsi setup and hook it into the VOP as well. > As described in the general dual-dsi devicetree binding, the panel should > define two input ports and point each of them to one of the used dsi- > controllers, as well as declare one of them as clock-master. > This is used to determine the dual-dsi state and get access to both > controller instances. > > v6: > handle master+slave component in dsi-attach > v5: > use driver-internal mechanism to find dual dsi slave > v4: > add component directly in probe when adding empty dsi slave controller > > Signed-off-by: Heiko Stuebner <heiko@sntech.de> This is not what I really like (putting dual display functionality into poor dsi driver), but it at least works. So: Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> The patchset is quite long on the list so if there will be no objections I will merge it tomorrow. -- Regards Andrzej > --- > .../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 136 ++++++++++++++++++ > drivers/gpu/drm/rockchip/rockchip_drm_drv.h | 1 + > drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 3 + > drivers/gpu/drm/rockchip/rockchip_drm_vop.h | 4 + > drivers/gpu/drm/rockchip/rockchip_vop_reg.c | 1 + > 5 files changed, 145 insertions(+) > > diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c > index b3aae8439aa3..63b028602d08 100644 > --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c > +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c > @@ -218,6 +218,10 @@ struct dw_mipi_dsi_rockchip { > struct clk *grf_clk; > struct clk *phy_cfg_clk; > > + /* dual-channel */ > + bool is_slave; > + struct dw_mipi_dsi_rockchip *slave; > + > unsigned int lane_mbps; /* per lane */ > u16 input_div; > u16 feedback_div; > @@ -226,6 +230,7 @@ struct dw_mipi_dsi_rockchip { > struct dw_mipi_dsi *dmd; > const struct rockchip_dw_dsi_chip_data *cdata; > struct dw_mipi_dsi_plat_data pdata; > + int devcnt; > }; > > struct dphy_pll_parameter_map { > @@ -602,6 +607,8 @@ dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder, > } > > s->output_type = DRM_MODE_CONNECTOR_DSI; > + if (dsi->slave) > + s->output_flags = ROCKCHIP_OUTPUT_DSI_DUAL; > > return 0; > } > @@ -617,6 +624,8 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) > return; > > pm_runtime_get_sync(dsi->dev); > + if (dsi->slave) > + pm_runtime_get_sync(dsi->slave->dev); > > /* > * For the RK3399, the clk of grf must be enabled before writing grf > @@ -630,6 +639,8 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) > } > > dw_mipi_dsi_rockchip_config(dsi, mux); > + if (dsi->slave) > + dw_mipi_dsi_rockchip_config(dsi->slave, mux); > > clk_disable_unprepare(dsi->grf_clk); > } > @@ -638,6 +649,8 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) > { > struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); > > + if (dsi->slave) > + pm_runtime_put(dsi->slave->dev); > pm_runtime_put(dsi->dev); > } > > @@ -673,14 +686,113 @@ static int rockchip_dsi_drm_create_encoder(struct dw_mipi_dsi_rockchip *dsi, > return 0; > } > > +static struct device > +*dw_mipi_dsi_rockchip_find_second(struct dw_mipi_dsi_rockchip *dsi) > +{ > + const struct of_device_id *match; > + struct device_node *node = NULL, *local; > + > + match = of_match_device(dsi->dev->driver->of_match_table, dsi->dev); > + > + local = of_graph_get_remote_node(dsi->dev->of_node, 1, 0); > + if (!local) > + return NULL; > + > + while ((node = of_find_compatible_node(node, NULL, > + match->compatible))) { > + struct device_node *remote; > + > + /* found ourself */ > + if (node == dsi->dev->of_node) > + continue; > + > + remote = of_graph_get_remote_node(node, 1, 0); > + if (!remote) > + continue; > + > + /* same display device in port1-ep0 for both */ > + if (remote == local) { > + struct dw_mipi_dsi_rockchip *dsi2; > + struct platform_device *pdev; > + > + pdev = of_find_device_by_node(node); > + > + /* > + * we have found the second, so will either return it > + * or return with an error. In any case won't need the > + * nodes anymore nor continue the loop. > + */ > + of_node_put(remote); > + of_node_put(node); > + of_node_put(local); > + > + if (!pdev) > + return ERR_PTR(-EPROBE_DEFER); > + > + dsi2 = platform_get_drvdata(pdev); > + if (!dsi2) { > + platform_device_put(pdev); > + return ERR_PTR(-EPROBE_DEFER); > + } > + > + return &pdev->dev; > + } > + > + of_node_put(remote); > + } > + > + of_node_put(local); > + > + return NULL; > +} > + > static int dw_mipi_dsi_rockchip_bind(struct device *dev, > struct device *master, > void *data) > { > struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); > struct drm_device *drm_dev = data; > + struct device *second; > + bool master1, master2; > int ret; > > + second = dw_mipi_dsi_rockchip_find_second(dsi); > + if (IS_ERR(second)) > + return PTR_ERR(second); > + > + if (second) { > + master1 = of_property_read_bool(dsi->dev->of_node, > + "clock-master"); > + master2 = of_property_read_bool(second->of_node, > + "clock-master"); > + > + if (master1 && master2) { > + DRM_DEV_ERROR(dsi->dev, "only one clock-master allowed\n"); > + return -EINVAL; > + } > + > + if (!master1 && !master2) { > + DRM_DEV_ERROR(dsi->dev, "no clock-master defined\n"); > + return -EINVAL; > + } > + > + /* we are the slave in dual-DSI */ > + if (!master1) { > + dsi->is_slave = true; > + return 0; > + } > + > + dsi->slave = dev_get_drvdata(second); > + if (!dsi->slave) { > + DRM_DEV_ERROR(dev, "could not get slaves data\n"); > + return -ENODEV; > + } > + > + dsi->slave->is_slave = true; > + dw_mipi_dsi_set_slave(dsi->dmd, dsi->slave->dmd); > + put_device(second); > + } > + > ret = clk_prepare_enable(dsi->pllref_clk); > if (ret) { > DRM_DEV_ERROR(dev, "Failed to enable pllref_clk: %d\n", ret); > @@ -708,6 +819,9 @@ static void dw_mipi_dsi_rockchip_unbind(struct device *dev, > { > struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); > > + if (dsi->is_slave) > + return; > + > dw_mipi_dsi_unbind(dsi->dmd); > > clk_disable_unprepare(dsi->pllref_clk); > @@ -722,6 +836,7 @@ static int dw_mipi_dsi_rockchip_host_attach(void *priv_data, > struct mipi_dsi_device *device) > { > struct dw_mipi_dsi_rockchip *dsi = priv_data; > + struct device *second; > int ret; > > ret = component_add(dsi->dev, &dw_mipi_dsi_rockchip_ops); > @@ -731,6 +846,19 @@ static int dw_mipi_dsi_rockchip_host_attach(void *priv_data, > return ret; > } > > + second = dw_mipi_dsi_rockchip_find_second(dsi); > + if (IS_ERR(second)) > + return PTR_ERR(second); > + if (second) { > + ret = component_add(second, &dw_mipi_dsi_rockchip_ops); > + if (ret) { > + DRM_DEV_ERROR(second, > + "Failed to register component: %d\n", > + ret); > + return ret; > + } > + } > + > return 0; > } > > @@ -738,6 +866,11 @@ static int dw_mipi_dsi_rockchip_host_detach(void *priv_data, > struct mipi_dsi_device *device) > { > struct dw_mipi_dsi_rockchip *dsi = priv_data; > + struct device *second; > + > + second = dw_mipi_dsi_rockchip_find_second(dsi); > + if (second && !IS_ERR(second)) > + component_del(second, &dw_mipi_dsi_rockchip_ops); > > component_del(dsi->dev, &dw_mipi_dsi_rockchip_ops); > > @@ -846,6 +979,9 @@ static int dw_mipi_dsi_rockchip_remove(struct platform_device *pdev) > { > struct dw_mipi_dsi_rockchip *dsi = platform_get_drvdata(pdev); > > + if (dsi->devcnt == 0) > + component_del(dsi->dev, &dw_mipi_dsi_rockchip_ops); > + > dw_mipi_dsi_remove(dsi->dmd); > > return 0; > diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h > index 453fef6a55b9..ce48568ec8a0 100644 > --- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h > +++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h > @@ -37,6 +37,7 @@ struct rockchip_crtc_state { > int output_type; > int output_mode; > int output_bpc; > + int output_flags; > }; > #define to_rockchip_crtc_state(s) \ > container_of(s, struct rockchip_crtc_state, base) > diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c > index 0c35a88e33dd..fb70fb486fbf 100644 > --- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c > +++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c > @@ -916,6 +916,7 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc, > pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC) ? > BIT(VSYNC_POSITIVE) : 0; > VOP_REG_SET(vop, output, pin_pol, pin_pol); > + VOP_REG_SET(vop, output, mipi_dual_channel_en, 0); > > switch (s->output_type) { > case DRM_MODE_CONNECTOR_LVDS: > @@ -933,6 +934,8 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc, > case DRM_MODE_CONNECTOR_DSI: > VOP_REG_SET(vop, output, mipi_pin_pol, pin_pol); > VOP_REG_SET(vop, output, mipi_en, 1); > + VOP_REG_SET(vop, output, mipi_dual_channel_en, > + !!(s->output_flags & ROCKCHIP_OUTPUT_DSI_DUAL)); > break; > case DRM_MODE_CONNECTOR_DisplayPort: > pin_pol &= ~BIT(DCLK_INVERT); > diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.h b/drivers/gpu/drm/rockchip/rockchip_drm_vop.h > index fd5765dfd637..0fe40e1983d9 100644 > --- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.h > +++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.h > @@ -60,6 +60,7 @@ struct vop_output { > struct vop_reg edp_en; > struct vop_reg hdmi_en; > struct vop_reg mipi_en; > + struct vop_reg mipi_dual_channel_en; > struct vop_reg rgb_en; > }; > > @@ -214,6 +215,9 @@ struct vop_data { > /* for use special outface */ > #define ROCKCHIP_OUT_MODE_AAAA 15 > > +/* output flags */ > +#define ROCKCHIP_OUTPUT_DSI_DUAL BIT(0) > + > enum alpha_mode { > ALPHA_STRAIGHT, > ALPHA_INVERSE, > diff --git a/drivers/gpu/drm/rockchip/rockchip_vop_reg.c b/drivers/gpu/drm/rockchip/rockchip_vop_reg.c > index 047a8867af90..08fc40af52c8 100644 > --- a/drivers/gpu/drm/rockchip/rockchip_vop_reg.c > +++ b/drivers/gpu/drm/rockchip/rockchip_vop_reg.c > @@ -634,6 +634,7 @@ static const struct vop_output rk3399_output = { > .hdmi_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 13), > .edp_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 14), > .mipi_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 15), > + .mipi_dual_channel_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 3), > }; > > static const struct vop_data rk3399_vop_big = { _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v6 7/7] drm/rockchip: dsi: add dual mipi support @ 2018-10-29 14:15 ` Andrzej Hajda 0 siblings, 0 replies; 20+ messages in thread From: Andrzej Hajda @ 2018-10-29 14:15 UTC (permalink / raw) To: linux-arm-kernel On 01.10.2018 14:38, Heiko Stuebner wrote: > Add the Rockchip-sepcific dual-dsi setup and hook it into the VOP as well. > As described in the general dual-dsi devicetree binding, the panel should > define two input ports and point each of them to one of the used dsi- > controllers, as well as declare one of them as clock-master. > This is used to determine the dual-dsi state and get access to both > controller instances. > > v6: > handle master+slave component in dsi-attach > v5: > use driver-internal mechanism to find dual dsi slave > v4: > add component directly in probe when adding empty dsi slave controller > > Signed-off-by: Heiko Stuebner <heiko@sntech.de> This is not what I really like (putting dual display functionality into poor dsi driver), but it at least works. So: Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> The patchset is quite long on the list so if there will be no objections I will merge it tomorrow. ?-- Regards Andrzej > --- > .../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 136 ++++++++++++++++++ > drivers/gpu/drm/rockchip/rockchip_drm_drv.h | 1 + > drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 3 + > drivers/gpu/drm/rockchip/rockchip_drm_vop.h | 4 + > drivers/gpu/drm/rockchip/rockchip_vop_reg.c | 1 + > 5 files changed, 145 insertions(+) > > diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c > index b3aae8439aa3..63b028602d08 100644 > --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c > +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c > @@ -218,6 +218,10 @@ struct dw_mipi_dsi_rockchip { > struct clk *grf_clk; > struct clk *phy_cfg_clk; > > + /* dual-channel */ > + bool is_slave; > + struct dw_mipi_dsi_rockchip *slave; > + > unsigned int lane_mbps; /* per lane */ > u16 input_div; > u16 feedback_div; > @@ -226,6 +230,7 @@ struct dw_mipi_dsi_rockchip { > struct dw_mipi_dsi *dmd; > const struct rockchip_dw_dsi_chip_data *cdata; > struct dw_mipi_dsi_plat_data pdata; > + int devcnt; > }; > > struct dphy_pll_parameter_map { > @@ -602,6 +607,8 @@ dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder, > } > > s->output_type = DRM_MODE_CONNECTOR_DSI; > + if (dsi->slave) > + s->output_flags = ROCKCHIP_OUTPUT_DSI_DUAL; > > return 0; > } > @@ -617,6 +624,8 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) > return; > > pm_runtime_get_sync(dsi->dev); > + if (dsi->slave) > + pm_runtime_get_sync(dsi->slave->dev); > > /* > * For the RK3399, the clk of grf must be enabled before writing grf > @@ -630,6 +639,8 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder) > } > > dw_mipi_dsi_rockchip_config(dsi, mux); > + if (dsi->slave) > + dw_mipi_dsi_rockchip_config(dsi->slave, mux); > > clk_disable_unprepare(dsi->grf_clk); > } > @@ -638,6 +649,8 @@ static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) > { > struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder); > > + if (dsi->slave) > + pm_runtime_put(dsi->slave->dev); > pm_runtime_put(dsi->dev); > } > > @@ -673,14 +686,113 @@ static int rockchip_dsi_drm_create_encoder(struct dw_mipi_dsi_rockchip *dsi, > return 0; > } > > +static struct device > +*dw_mipi_dsi_rockchip_find_second(struct dw_mipi_dsi_rockchip *dsi) > +{ > + const struct of_device_id *match; > + struct device_node *node = NULL, *local; > + > + match = of_match_device(dsi->dev->driver->of_match_table, dsi->dev); > + > + local = of_graph_get_remote_node(dsi->dev->of_node, 1, 0); > + if (!local) > + return NULL; > + > + while ((node = of_find_compatible_node(node, NULL, > + match->compatible))) { > + struct device_node *remote; > + > + /* found ourself */ > + if (node == dsi->dev->of_node) > + continue; > + > + remote = of_graph_get_remote_node(node, 1, 0); > + if (!remote) > + continue; > + > + /* same display device in port1-ep0 for both */ > + if (remote == local) { > + struct dw_mipi_dsi_rockchip *dsi2; > + struct platform_device *pdev; > + > + pdev = of_find_device_by_node(node); > + > + /* > + * we have found the second, so will either return it > + * or return with an error. In any case won't need the > + * nodes anymore nor continue the loop. > + */ > + of_node_put(remote); > + of_node_put(node); > + of_node_put(local); > + > + if (!pdev) > + return ERR_PTR(-EPROBE_DEFER); > + > + dsi2 = platform_get_drvdata(pdev); > + if (!dsi2) { > + platform_device_put(pdev); > + return ERR_PTR(-EPROBE_DEFER); > + } > + > + return &pdev->dev; > + } > + > + of_node_put(remote); > + } > + > + of_node_put(local); > + > + return NULL; > +} > + > static int dw_mipi_dsi_rockchip_bind(struct device *dev, > struct device *master, > void *data) > { > struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); > struct drm_device *drm_dev = data; > + struct device *second; > + bool master1, master2; > int ret; > > + second = dw_mipi_dsi_rockchip_find_second(dsi); > + if (IS_ERR(second)) > + return PTR_ERR(second); > + > + if (second) { > + master1 = of_property_read_bool(dsi->dev->of_node, > + "clock-master"); > + master2 = of_property_read_bool(second->of_node, > + "clock-master"); > + > + if (master1 && master2) { > + DRM_DEV_ERROR(dsi->dev, "only one clock-master allowed\n"); > + return -EINVAL; > + } > + > + if (!master1 && !master2) { > + DRM_DEV_ERROR(dsi->dev, "no clock-master defined\n"); > + return -EINVAL; > + } > + > + /* we are the slave in dual-DSI */ > + if (!master1) { > + dsi->is_slave = true; > + return 0; > + } > + > + dsi->slave = dev_get_drvdata(second); > + if (!dsi->slave) { > + DRM_DEV_ERROR(dev, "could not get slaves data\n"); > + return -ENODEV; > + } > + > + dsi->slave->is_slave = true; > + dw_mipi_dsi_set_slave(dsi->dmd, dsi->slave->dmd); > + put_device(second); > + } > + > ret = clk_prepare_enable(dsi->pllref_clk); > if (ret) { > DRM_DEV_ERROR(dev, "Failed to enable pllref_clk: %d\n", ret); > @@ -708,6 +819,9 @@ static void dw_mipi_dsi_rockchip_unbind(struct device *dev, > { > struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev); > > + if (dsi->is_slave) > + return; > + > dw_mipi_dsi_unbind(dsi->dmd); > > clk_disable_unprepare(dsi->pllref_clk); > @@ -722,6 +836,7 @@ static int dw_mipi_dsi_rockchip_host_attach(void *priv_data, > struct mipi_dsi_device *device) > { > struct dw_mipi_dsi_rockchip *dsi = priv_data; > + struct device *second; > int ret; > > ret = component_add(dsi->dev, &dw_mipi_dsi_rockchip_ops); > @@ -731,6 +846,19 @@ static int dw_mipi_dsi_rockchip_host_attach(void *priv_data, > return ret; > } > > + second = dw_mipi_dsi_rockchip_find_second(dsi); > + if (IS_ERR(second)) > + return PTR_ERR(second); > + if (second) { > + ret = component_add(second, &dw_mipi_dsi_rockchip_ops); > + if (ret) { > + DRM_DEV_ERROR(second, > + "Failed to register component: %d\n", > + ret); > + return ret; > + } > + } > + > return 0; > } > > @@ -738,6 +866,11 @@ static int dw_mipi_dsi_rockchip_host_detach(void *priv_data, > struct mipi_dsi_device *device) > { > struct dw_mipi_dsi_rockchip *dsi = priv_data; > + struct device *second; > + > + second = dw_mipi_dsi_rockchip_find_second(dsi); > + if (second && !IS_ERR(second)) > + component_del(second, &dw_mipi_dsi_rockchip_ops); > > component_del(dsi->dev, &dw_mipi_dsi_rockchip_ops); > > @@ -846,6 +979,9 @@ static int dw_mipi_dsi_rockchip_remove(struct platform_device *pdev) > { > struct dw_mipi_dsi_rockchip *dsi = platform_get_drvdata(pdev); > > + if (dsi->devcnt == 0) > + component_del(dsi->dev, &dw_mipi_dsi_rockchip_ops); > + > dw_mipi_dsi_remove(dsi->dmd); > > return 0; > diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h > index 453fef6a55b9..ce48568ec8a0 100644 > --- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h > +++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h > @@ -37,6 +37,7 @@ struct rockchip_crtc_state { > int output_type; > int output_mode; > int output_bpc; > + int output_flags; > }; > #define to_rockchip_crtc_state(s) \ > container_of(s, struct rockchip_crtc_state, base) > diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c > index 0c35a88e33dd..fb70fb486fbf 100644 > --- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c > +++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c > @@ -916,6 +916,7 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc, > pin_pol |= (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC) ? > BIT(VSYNC_POSITIVE) : 0; > VOP_REG_SET(vop, output, pin_pol, pin_pol); > + VOP_REG_SET(vop, output, mipi_dual_channel_en, 0); > > switch (s->output_type) { > case DRM_MODE_CONNECTOR_LVDS: > @@ -933,6 +934,8 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc, > case DRM_MODE_CONNECTOR_DSI: > VOP_REG_SET(vop, output, mipi_pin_pol, pin_pol); > VOP_REG_SET(vop, output, mipi_en, 1); > + VOP_REG_SET(vop, output, mipi_dual_channel_en, > + !!(s->output_flags & ROCKCHIP_OUTPUT_DSI_DUAL)); > break; > case DRM_MODE_CONNECTOR_DisplayPort: > pin_pol &= ~BIT(DCLK_INVERT); > diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.h b/drivers/gpu/drm/rockchip/rockchip_drm_vop.h > index fd5765dfd637..0fe40e1983d9 100644 > --- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.h > +++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.h > @@ -60,6 +60,7 @@ struct vop_output { > struct vop_reg edp_en; > struct vop_reg hdmi_en; > struct vop_reg mipi_en; > + struct vop_reg mipi_dual_channel_en; > struct vop_reg rgb_en; > }; > > @@ -214,6 +215,9 @@ struct vop_data { > /* for use special outface */ > #define ROCKCHIP_OUT_MODE_AAAA 15 > > +/* output flags */ > +#define ROCKCHIP_OUTPUT_DSI_DUAL BIT(0) > + > enum alpha_mode { > ALPHA_STRAIGHT, > ALPHA_INVERSE, > diff --git a/drivers/gpu/drm/rockchip/rockchip_vop_reg.c b/drivers/gpu/drm/rockchip/rockchip_vop_reg.c > index 047a8867af90..08fc40af52c8 100644 > --- a/drivers/gpu/drm/rockchip/rockchip_vop_reg.c > +++ b/drivers/gpu/drm/rockchip/rockchip_vop_reg.c > @@ -634,6 +634,7 @@ static const struct vop_output rk3399_output = { > .hdmi_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 13), > .edp_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 14), > .mipi_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 15), > + .mipi_dual_channel_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 3), > }; > > static const struct vop_data rk3399_vop_big = { ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v6 0/8] drm/rockchip: migrate to common dw-mipi-dsi bridge and dual-dsi 2018-10-01 12:38 ` Heiko Stuebner @ 2018-10-30 13:57 ` Andrzej Hajda -1 siblings, 0 replies; 20+ messages in thread From: Andrzej Hajda @ 2018-10-30 13:57 UTC (permalink / raw) To: Heiko Stuebner, architt, hjc Cc: briannorris, hoegsberg, philippe.cornu, dri-devel, yannick.fertre, linux-rockchip, nickey.yang, mka, seanpaul, linux-arm-kernel On 01.10.2018 14:38, Heiko Stuebner wrote: > The Rockchip DSI driver was separate till now, not using the common > bridge driver that was introduced a bit later. So this series migrates > over to use that common bridge driver and then also adds support for > dual-dsi to both the bridge and Rockchip glue code. Queued to drm-misc-next. Regards Andrzej _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v6 0/8] drm/rockchip: migrate to common dw-mipi-dsi bridge and dual-dsi @ 2018-10-30 13:57 ` Andrzej Hajda 0 siblings, 0 replies; 20+ messages in thread From: Andrzej Hajda @ 2018-10-30 13:57 UTC (permalink / raw) To: linux-arm-kernel On 01.10.2018 14:38, Heiko Stuebner wrote: > The Rockchip DSI driver was separate till now, not using the common > bridge driver that was introduced a bit later. So this series migrates > over to use that common bridge driver and then also adds support for > dual-dsi to both the bridge and Rockchip glue code. Queued to drm-misc-next. Regards Andrzej ^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2018-10-30 13:57 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <CGME20181001132341epcas3p18117df45780e88a4121e0fe22e47e8e7@epcas3p1.samsung.com>
2018-10-01 12:38 ` [PATCH v6 0/8] drm/rockchip: migrate to common dw-mipi-dsi bridge and dual-dsi Heiko Stuebner
2018-10-01 12:38 ` Heiko Stuebner
2018-10-01 12:38 ` [PATCH v6 1/7] drm/bridge/synopsys: dsi: move mipi_dsi_host_unregister to __dw_mipi_dsi_remove Heiko Stuebner
2018-10-01 12:38 ` Heiko Stuebner
2018-10-01 12:38 ` [PATCH v6 2/7] drm/bridge/synopsys: dsi: don't call __dw_mipi_dsi_probe from dw_mipi_dsi_bind Heiko Stuebner
2018-10-01 12:38 ` Heiko Stuebner
2018-10-01 12:38 ` [PATCH v6 3/7] drm/bridge/synopsys: dsi: add ability to have glue-specific attach and detach Heiko Stuebner
2018-10-01 12:38 ` Heiko Stuebner
2018-10-01 12:38 ` [PATCH v6 4/7] dt-bindings: display: rockchip: update DSI controller Heiko Stuebner
2018-10-01 12:38 ` Heiko Stuebner
2018-10-01 12:38 ` [PATCH v6 5/7] drm/rockchip: dsi: migrate to use dw-mipi-dsi bridge driver Heiko Stuebner
2018-10-01 12:38 ` Heiko Stuebner
2018-10-01 12:38 ` [PATCH v6 6/7] drm/bridge/synopsys: dsi: add dual-dsi support Heiko Stuebner
2018-10-01 12:38 ` Heiko Stuebner
2018-10-01 12:38 ` [PATCH v6 7/7] drm/rockchip: dsi: add dual mipi support Heiko Stuebner
2018-10-01 12:38 ` Heiko Stuebner
2018-10-29 14:15 ` Andrzej Hajda
2018-10-29 14:15 ` Andrzej Hajda
2018-10-30 13:57 ` [PATCH v6 0/8] drm/rockchip: migrate to common dw-mipi-dsi bridge and dual-dsi Andrzej Hajda
2018-10-30 13:57 ` Andrzej Hajda
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.