* [U-Boot] [PATCH] arc: Add support for IoT development kit
@ 2018-10-04 11:12 Alexey Brodkin
0 siblings, 0 replies; only message in thread
From: Alexey Brodkin @ 2018-10-04 11:12 UTC (permalink / raw)
To: u-boot
The DesignWare ARC IoT Development Kit is a versatile platform
that includes the necessary hardware and software to accelerate
software development and debugging of sensor fusion,
voice recognition and face detection designs.
More information is avaialble here [1] and here [2].
The board is based on real silicon with
ARC EM9D-based Data Fusion IP Subsystem.
It sports a rich set of I/O including
* DW USB OTG
* DW MobileStorage (used for micro SD-card)
* GPIO
* multiple serial interface including DW APB UART
* ADC, PWM and eFlash, SRAM and SPI Flash memory
* Real-Time Clock (RTC)
* Bluetooth module with worldwide regulatory compliance
(FCC, IC, CE, ETSI, TELEC)
* On-board 9-axis sensor (gyro, accelerometer and compass)
Extensible with Arduino, Pmod, mikroBUS connectors and a 2x18
extension header.
One of the most interesting features for developers is built-in
Digilent USB JTAG probe so only micro-USB cable is needed!
[1] https://www.synopsys.com/dw/ipdir.php?ds=arc_iot_development_kit
[2] https://www.synopsys.com/dw/doc.php/ds/cc/iot_dev_kit.pdf
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
---
arch/arc/Kconfig | 5 +
arch/arc/dts/Makefile | 1 +
arch/arc/dts/iot_devkit.dts | 45 +++++++
board/synopsys/iot_devkit/Kconfig | 12 ++
board/synopsys/iot_devkit/MAINTAINERS | 5 +
board/synopsys/iot_devkit/Makefile | 7 ++
board/synopsys/iot_devkit/config.mk | 2 +
board/synopsys/iot_devkit/iot_devkit.c | 168 +++++++++++++++++++++++++
board/synopsys/iot_devkit/u-boot.lds | 77 ++++++++++++
configs/iot_devkit_defconfig | 38 ++++++
include/configs/iot_devkit.h | 84 +++++++++++++
11 files changed, 444 insertions(+)
create mode 100644 arch/arc/dts/iot_devkit.dts
create mode 100644 board/synopsys/iot_devkit/Kconfig
create mode 100644 board/synopsys/iot_devkit/MAINTAINERS
create mode 100644 board/synopsys/iot_devkit/Makefile
create mode 100644 board/synopsys/iot_devkit/config.mk
create mode 100644 board/synopsys/iot_devkit/iot_devkit.c
create mode 100644 board/synopsys/iot_devkit/u-boot.lds
create mode 100644 configs/iot_devkit_defconfig
create mode 100644 include/configs/iot_devkit.h
diff --git a/arch/arc/Kconfig b/arch/arc/Kconfig
index d59aa3ae291e..b24593e137b3 100644
--- a/arch/arc/Kconfig
+++ b/arch/arc/Kconfig
@@ -157,6 +157,10 @@ config TARGET_EMDK
config TARGET_HSDK
bool "Support Synpsys HS DevelopmentKit board"
+config TARGET_IOT_DEVKIT
+ bool "Synopsys Brite IoT Development kit"
+ select CPU_ARCEM6
+
endchoice
source "board/abilis/tb100/Kconfig"
@@ -164,5 +168,6 @@ source "board/synopsys/Kconfig"
source "board/synopsys/axs10x/Kconfig"
source "board/synopsys/emdk/Kconfig"
source "board/synopsys/hsdk/Kconfig"
+source "board/synopsys/iot_devkit/Kconfig"
endmenu
diff --git a/arch/arc/dts/Makefile b/arch/arc/dts/Makefile
index 491a4f40bbc7..17e1405c0c48 100644
--- a/arch/arc/dts/Makefile
+++ b/arch/arc/dts/Makefile
@@ -6,6 +6,7 @@ dtb-$(CONFIG_TARGET_NSIM) += nsim.dtb
dtb-$(CONFIG_TARGET_TB100) += abilis_tb100.dtb
dtb-$(CONFIG_TARGET_EMDK) += emdk.dtb
dtb-$(CONFIG_TARGET_HSDK) += hsdk.dtb
+dtb-$(CONFIG_TARGET_IOT_DEVKIT) += iot_devkit.dtb
targets += $(dtb-y)
diff --git a/arch/arc/dts/iot_devkit.dts b/arch/arc/dts/iot_devkit.dts
new file mode 100644
index 000000000000..ebf5a950f0f2
--- /dev/null
+++ b/arch/arc/dts/iot_devkit.dts
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Synopsys, Inc. All rights reserved.
+ */
+/dts-v1/;
+
+#include "skeleton.dtsi"
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ console = &uart0;
+ };
+
+ cpu_card {
+ core_clk: core_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <144000000>;
+ u-boot,dm-pre-reloc;
+ };
+ };
+
+ uart0: serial0 at 80014000 {
+ compatible = "snps,dw-apb-uart";
+ clock-frequency = <16000000>;
+ reg = <0x80014000 0x1000>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+
+ usb: usb at f0040000 {
+ compatible = "snps,dwc2";
+ reg = <0xf0040000 0x10000>;
+ phys = <&usbphy>;
+ phy-names = "usb2-phy";
+ };
+
+ usbphy: phy {
+ compatible = "nop-phy";
+ #phy-cells = <0>;
+ };
+};
diff --git a/board/synopsys/iot_devkit/Kconfig b/board/synopsys/iot_devkit/Kconfig
new file mode 100644
index 000000000000..ad956b20f770
--- /dev/null
+++ b/board/synopsys/iot_devkit/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_IOT_DEVKIT
+
+config SYS_BOARD
+ default "iot_devkit"
+
+config SYS_VENDOR
+ default "synopsys"
+
+config SYS_CONFIG_NAME
+ default "iot_devkit"
+
+endif
diff --git a/board/synopsys/iot_devkit/MAINTAINERS b/board/synopsys/iot_devkit/MAINTAINERS
new file mode 100644
index 000000000000..06457cfa6ae2
--- /dev/null
+++ b/board/synopsys/iot_devkit/MAINTAINERS
@@ -0,0 +1,5 @@
+IOT DEVKIT BOARD
+M: Alexey Brodkin <abrodkin@synopsys.com>
+S: Maintained
+F: board/synopsys/iot_devkit/
+F: configs/iot_devkit_defconfig
diff --git a/board/synopsys/iot_devkit/Makefile b/board/synopsys/iot_devkit/Makefile
new file mode 100644
index 000000000000..161602464382
--- /dev/null
+++ b/board/synopsys/iot_devkit/Makefile
@@ -0,0 +1,7 @@
+#
+# Copyright (C) 2018 Synopsys, Inc. All rights reserved.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += iot_devkit.o
diff --git a/board/synopsys/iot_devkit/config.mk b/board/synopsys/iot_devkit/config.mk
new file mode 100644
index 000000000000..120733538a40
--- /dev/null
+++ b/board/synopsys/iot_devkit/config.mk
@@ -0,0 +1,2 @@
+PLATFORM_CPPFLAGS += -mlittle-endian -mcode-density -mdiv-rem -mswap -mnorm -mmpy-option=6 -mbarrel-shifter
+LDSCRIPT = $(srctree)/board/synopsys/iot_devkit/u-boot.lds
diff --git a/board/synopsys/iot_devkit/iot_devkit.c b/board/synopsys/iot_devkit/iot_devkit.c
new file mode 100644
index 000000000000..c185d5cdb5cc
--- /dev/null
+++ b/board/synopsys/iot_devkit/iot_devkit.c
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Synopsys, Inc. All rights reserved.
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <dwmmc.h>
+#include <linux/libfdt.h>
+#include <fdtdec.h>
+
+#include <asm/arcregs.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define SYSCON_BASE 0xf000a000
+#define AHBCKDIV (void *)(SYSCON_BASE + 0x04)
+#define APBCKDIV (void *)(SYSCON_BASE + 0x08)
+#define APBCKEN (void *)(SYSCON_BASE + 0x0C)
+#define CLKSEL (void *)(SYSCON_BASE + 0x24)
+#define CLKSTAT (void *)(SYSCON_BASE + 0x28)
+#define PLLCON (void *)(SYSCON_BASE + 0x2C)
+#define APBCKSEL (void *)(SYSCON_BASE + 0x30)
+#define AHBCKEN (void *)(SYSCON_BASE + 0x34)
+#define USBPHY_PLL (void *)(SYSCON_BASE + 0x78)
+#define USBCFG (void *)(SYSCON_BASE + 0x7c)
+
+#define PLL_MASK_0 0xffcfffff
+#define PLL_MASK_1 0xffcfff00
+#define PLL_MASK_2 0xfbcfff00
+
+#define CLKSEL_DEFAULT 0x5a690000
+
+static int set_cpu_freq(unsigned int clk)
+{
+ clk /= 1000000;
+
+ /* Set clk to ext Xtal (LSN value 0) */
+ writel(CLKSEL_DEFAULT, CLKSEL);
+
+ switch (clk) {
+ case 16:
+ /* Bypass mode */
+ return 0;
+
+ case 50:
+ writel(readl(PLLCON) & PLL_MASK_0, PLLCON);
+ /* pll_off=1, M=25, N=1, OD=3, PLL_OUT_CLK=50M */
+ writel((readl(PLLCON) & PLL_MASK_1) | 0x300191, PLLCON);
+ /* pll_off=0, M=25, N=1, OD=3, PLL_OUT_CLK=50M */
+ writel((readl(PLLCON) & PLL_MASK_2) | 0x300191, PLLCON);
+ break;
+
+ case 72:
+ writel(readl(PLLCON) & PLL_MASK_0, PLLCON);
+ /* pll_off=1, M=18, N=1, OD=2, PLL_OUT_CLK=72M */
+ writel((readl(PLLCON) & PLL_MASK_1) | 0x200121, PLLCON);
+ /* pll_off=0, M=18, N=1, OD=2, PLL_OUT_CLK=72M */
+ writel((readl(PLLCON) & PLL_MASK_2) | 0x200121, PLLCON);
+ break;
+
+ case 100:
+ writel(readl(PLLCON) & PLL_MASK_0, PLLCON);
+ /* pll_off=1,M=25, N=1, OD=2, PLL_OUT_CLK=100M */
+ writel((readl(PLLCON) & PLL_MASK_1) | 0x200191, PLLCON);
+ /* pll_off=0,M=25, N=1, OD=2, PLL_OUT_CLK=100M */
+ writel((readl(PLLCON) & PLL_MASK_2) | 0x200191, PLLCON);
+ break;
+
+ case 144:
+ writel(readl(PLLCON) & PLL_MASK_0, PLLCON);
+ /* pll_off=1, M=18, N=1, OD=1, PLL_OUT_CLK=144M */
+ writel((readl(PLLCON) & PLL_MASK_1) | 0x100121, PLLCON);
+ /* pll_off=0, M=18, N=1, OD=1, PLL_OUT_CLK=144M */
+ writel((readl(PLLCON) & PLL_MASK_2) | 0x100121, PLLCON);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ while (!(readl(CLKSTAT) & 0x4))
+ ;
+
+ /* Set clk from PLL on bus (LSN = 1) */
+ writel(CLKSEL_DEFAULT | BIT(0), CLKSEL);
+
+ return 0;
+}
+
+extern u8 __rom_end[];
+extern u8 __ram_start[];
+extern u8 __ram_end[];
+
+/*
+ * Use mach_cpu_init() for .data section copy as board_early_init_f() will be
+ * too late: initf_dm() will use a value of "av_" variable from not yet
+ * initialized (by copy) area.
+ */
+int mach_cpu_init(void)
+{
+ int offset, freq;
+
+ /* Don't relocate U-Boot */
+ gd->flags |= GD_FLG_SKIP_RELOC;
+
+ /* Copy data from ROM to RAM */
+ u8 *src = __rom_end;
+ u8 *dst = __ram_start;
+
+ while (dst < __ram_end)
+ *dst++ = *src++;
+
+ /* Enable debug uart */
+#define DEBUG_UART_BASE 0x80014000
+#define DEBUG_UART_DLF_OFFSET 0xc0
+ write_aux_reg(DEBUG_UART_BASE + DEBUG_UART_DLF_OFFSET, 1);
+
+ offset = fdt_path_offset(gd->fdt_blob, "/cpu_card/core_clk");
+ if (offset < 0)
+ return offset;
+
+ freq = fdtdec_get_int(gd->fdt_blob, offset, "clock-frequency", 0);
+ if (!freq)
+ return -EINVAL;
+
+ /* If CPU freq > 100 MHz, divide eFLASH clock by 2 */
+ if (freq > 100000000) {
+ u32 reg = readl(AHBCKDIV);
+
+ reg &= ~(0xF << 8);
+ reg |= 2 << 8;
+ writel(reg, AHBCKDIV);
+ }
+
+ return set_cpu_freq(freq);
+}
+
+#define ARC_PERIPHERAL_BASE 0xF0000000
+#define SDIO_BASE (ARC_PERIPHERAL_BASE + 0xB000)
+
+int board_mmc_init(bd_t *bis)
+{
+ struct dwmci_host *host = NULL;
+
+ host = malloc(sizeof(struct dwmci_host));
+ if (!host) {
+ printf("dwmci_host malloc fail!\n");
+ return -ENOMEM;
+ }
+
+ memset(host, 0, sizeof(struct dwmci_host));
+ host->name = "Synopsys Mobile storage";
+ host->ioaddr = (void *)SDIO_BASE;
+ host->buswidth = 4;
+ host->dev_index = 0;
+ host->bus_hz = 50000000;
+
+ add_dwmci(host, host->bus_hz / 2, 400000);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: Synopsys IoT Development Kit\n");
+ return 0;
+};
diff --git a/board/synopsys/iot_devkit/u-boot.lds b/board/synopsys/iot_devkit/u-boot.lds
new file mode 100644
index 000000000000..d08316870553
--- /dev/null
+++ b/board/synopsys/iot_devkit/u-boot.lds
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2018 Synopsys, Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <config.h>
+
+MEMORY {
+ ROM : ORIGIN = ROM_BASE, LENGTH = ROM_SIZE
+ RAM : ORIGIN = RAM_DATA_BASE, LENGTH = RAM_DATA_SIZE
+}
+
+OUTPUT_FORMAT("elf32-littlearc", "elf32-littlearc", "elf32-littlearc")
+OUTPUT_ARCH(arc)
+ENTRY(_start)
+SECTIONS
+{
+ . = CONFIG_SYS_MONITOR_BASE;
+ __image_copy_start = .;
+ .ivt :
+ {
+ __ivt_start = .;
+ KEEP(*(.ivt));
+ __ivt_end = .;
+ } > ROM
+
+ . = ALIGN(1024);
+ .text : {
+ __text_start = .;
+ arch/arc/lib/start.o (.text*)
+ *(.text*)
+ __text_end = .;
+ } > ROM
+
+ . = ALIGN(4);
+ .rodata : {
+ *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
+ } > ROM
+
+ . = ALIGN(4);
+ .u_boot_list : {
+ KEEP(*(SORT(.u_boot_list*)));
+
+ /* Mark RAM's LMA */
+ . = ALIGN(4);
+ __rom_end = .;
+ } > ROM
+
+ .data : {
+ /* Mark RAM's VMA */
+ . = ALIGN(4);
+
+ /*
+ * Everything between __ram_start and __ram_start will be
+ * copied from ROM to RAM in board_early_init_f().
+ */
+ __ram_start = .;
+
+ *(.data*)
+
+ __ram_end = .;
+ } > RAM AT > ROM
+
+ .bss : {
+ . = ALIGN(1024);
+ __bss_start = .;
+ *(.bss*)
+ __bss_end = .;
+ } > RAM
+
+ /* Keep relocation-related symbols to make linker happy */
+ __rel_dyn_start = .;
+ __rel_dyn_end = .;
+ __image_copy_end = .;
+ __init_end = .;
+}
diff --git a/configs/iot_devkit_defconfig b/configs/iot_devkit_defconfig
new file mode 100644
index 000000000000..1f0f9c325676
--- /dev/null
+++ b/configs/iot_devkit_defconfig
@@ -0,0 +1,38 @@
+CONFIG_ARC=y
+CONFIG_ISA_ARCV2=y
+CONFIG_CPU_ARCEM6=y
+CONFIG_SYS_ICACHE_OFF=y
+CONFIG_SYS_DCACHE_OFF=y
+CONFIG_TARGET_IOT_DEVKIT=y
+CONFIG_SYS_TEXT_BASE=0x20000000
+CONFIG_SYS_CLK_FREQ=16000000
+# CONFIG_ARCH_FIXUP_FDT_MEMORY is not set
+CONFIG_SYS_PROMPT="IoTDK# "
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_BOOTM is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_NET is not set
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_DEFAULT_DEVICE_TREE="iot_devkit"
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_INTERFACE="mmc"
+CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
+CONFIG_DM=y
+CONFIG_MMC=y
+CONFIG_MMC_DW=y
+CONFIG_DM_SERIAL=y
+CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_DWC2_BUFFER_SIZE=16
+CONFIG_USB_STORAGE=y
+CONFIG_FS_FAT_MAX_CLUSTSIZE=4096
diff --git a/include/configs/iot_devkit.h b/include/configs/iot_devkit.h
new file mode 100644
index 000000000000..4ffe1141d922
--- /dev/null
+++ b/include/configs/iot_devkit.h
@@ -0,0 +1,84 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2018 Synopsys, Inc. All rights reserved.
+ */
+
+#ifndef _CONFIG_IOT_DEVKIT_H_
+#define _CONFIG_IOT_DEVKIT_H_
+
+#include <linux/sizes.h>
+
+/*
+ * MEMORY MAP
+ *
+ * eFlash: 0x0000_0000 - 0x0008_0000 (512K)
+ * ICCM: 0x2000_0000 - 0x2004_0000 (256K)
+ * SRAM: 0x3000_0000 - 0x3002_0000 (128K)
+ * DCCM: 0x8000_0000 - 0x8002_0000 (128K)
+ * Note: only data goes here, as IFQ cannot fetch instructions from DCCM
+ *
+ *
+ * RAM PARTITIONING
+ *
+ * +-----------+----------+---------------------+-------------+
+ * | <-- Stack | .data | Malloc | Environment |
+ * +-----------+----------+---------------------+-------------+
+ * : : : :\___________/
+ * : : : : |
+ * : : : : CONFIG_ENV_SIZE
+ * : : \____________________/
+ * : : |
+ * : : CONFIG_SYS_MALLOC_LEN
+ * : :
+ * : Specified explicitly by CONFIG_SYS_INIT_SP_ADDR
+ * :
+ * Specified explicitly by CONFIG_SYS_SDRAM_BASE
+ *
+ * NOTES:
+ * - Stack starts from CONFIG_SYS_INIT_SP_ADDR and grows down,
+ * i.e. towards CONFIG_SYS_SDRAM_BASE but nothing stops it from crossing
+ * that CONFIG_SYS_SDRAM_BASE in which case data won't be really saved on
+ * stack any longer and values popped from stack will contain garbage
+ * leading to unexpected behavior, typically but not limited to:
+ * - "Returning" back to bogus caller function
+ * - Reading data from weird addresses
+ */
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+
+#define SRAM_BASE 0x30000000
+#define SRAM_SIZE SZ_128K
+
+#define DCCM_BASE 0x80000000
+#define DCCM_SIZE SZ_128K
+
+#define CONFIG_SYS_SDRAM_BASE DCCM_BASE
+#define CONFIG_SYS_SDRAM_SIZE DCCM_SIZE
+
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_32K)
+
+#define CONFIG_SYS_MALLOC_LEN SZ_64K
+#define CONFIG_SYS_BOOTM_LEN SZ_128K
+#define CONFIG_SYS_LOAD_ADDR SRAM_BASE
+
+#define ROM_BASE CONFIG_SYS_MONITOR_BASE
+#define ROM_SIZE SZ_256K
+
+#define RAM_DATA_BASE CONFIG_SYS_INIT_SP_ADDR
+#define RAM_DATA_SIZE CONFIG_SYS_SDRAM_SIZE - \
+ (CONFIG_SYS_INIT_SP_ADDR - \
+ CONFIG_SYS_SDRAM_BASE) - \
+ CONFIG_SYS_MALLOC_LEN - \
+ CONFIG_ENV_SIZE
+
+/* Required by DW MMC driver */
+#define CONFIG_BOUNCE_BUFFER
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_SIZE SZ_4K
+#define CONFIG_BOOTFILE "app.bin"
+#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
+
+#endif /* _CONFIG_IOT_DEVKIT_H_ */
--
2.17.1
^ permalink raw reply related [flat|nested] only message in thread
only message in thread, other threads:[~2018-10-04 11:12 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-10-04 11:12 [U-Boot] [PATCH] arc: Add support for IoT development kit Alexey Brodkin
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.