[PATCH v8 1/3] [media] imx214: device tree binding

* [PATCH v8 1/3] [media] imx214: device tree binding
@ 2018-10-05 12:49 Ricardo Ribalda Delgado
  2018-10-05 12:49 ` [PATCH v8 2/3] [media] imx214: Add imx214 camera sensor driver Ricardo Ribalda Delgado
                   ` (3 more replies)
  0 siblings, 4 replies; 5+ messages in thread
From: Ricardo Ribalda Delgado @ 2018-10-05 12:49 UTC (permalink / raw)
  To: Hans Verkuil, Laurent Pinchart, Sakari Ailus,
	Mauro Carvalho Chehab, linux-kernel, linux-media, jacopo
  Cc: Ricardo Ribalda, devicetree

From: Ricardo Ribalda <ricardo.ribalda@gmail.com>

Document bindings for imx214 camera sensor

Cc: devicetree@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
---
 .../devicetree/bindings/media/i2c/imx214.txt  | 53 +++++++++++++++++++
 1 file changed, 53 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/imx214.txt

diff --git a/Documentation/devicetree/bindings/media/i2c/imx214.txt b/Documentation/devicetree/bindings/media/i2c/imx214.txt
new file mode 100644
index 000000000000..421a019ab7f9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imx214.txt
@@ -0,0 +1,53 @@
+* Sony 1/3.06-Inch 13.13Mp CMOS Digital Image Sensor
+
+The Sony imx214 is a 1/3.06-inch CMOS active pixel digital image sensor with
+an active array size of 4224H x 3200V. It is programmable through an I2C
+interface. The I2C address can be configured to 0x1a or 0x10, depending on
+how the hardware is wired.
+Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a maximum
+throughput of 1.2Gbps/lane.
+
+
+Required Properties:
+- compatible: value should be "sony,imx214" for imx214 sensor
+- reg: I2C bus address of the device
+- enable-gpios: GPIO descriptor for the enable pin.
+- vdddo-supply: Chip digital IO regulator (1.8V).
+- vdda-supply: Chip analog regulator (2.7V).
+- vddd-supply: Chip digital core regulator (1.12V).
+- clocks: Reference to the xclk clock.
+- clock-names:  Shall be "xclk".
+
+Optional Properties:
+- flash-leds: See ../video-interfaces.txt
+- lens-focus: See ../video-interfaces.txt
+
+The imx214 device node shall contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Required Properties on endpoint:
+- data-lanes: check ../video-interfaces.txt
+- link-frequencies: check ../video-interfaces.txt
+- remote-endpoint: check ../video-interfaces.txt
+
+Example:
+
+	camera_rear@1a {
+		compatible = "sony,imx214";
+		reg = <0x1a>;
+		vdddo-supply = <&pm8994_lvs1>;
+		vddd-supply = <&camera_vddd_1v12>;
+		vdda-supply = <&pm8994_l17>;
+		lens-focus = <&ad5820>;
+		enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>;
+		clocks = <&mmcc CAMSS_MCLK0_CLK>;
+		clock-names = "xclk";
+		port {
+			imx214_ep: endpoint {
+				data-lanes = <1 2 3 4>;
+				link-frequencies = /bits/ 64 <480000000>;
+				remote-endpoint = <&csiphy0_ep>;
+			};
+		};
+	};
-- 
2.19.0


^ permalink raw reply related	[flat|nested] 5+ messages in thread