[PATCH AUTOSEL 4.9 01/14] ASoC: wm8804: Add ACPI support

[PATCH AUTOSEL 4.9 01/14] ASoC: wm8804: Add ACPI support

[Sasha Levin]

From: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>

[ Upstream commit 960cdd50ca9fdfeb82c2757107bcb7f93c8d7d41 ]

HID made of either Wolfson/CirrusLogic PCI ID + 8804 identifier.

This helps enumerate the HifiBerry Digi+ HAT boards on the Up2 platform.

The scripts at https://github.com/thesofproject/acpi-scripts can be
used to add the ACPI initrd overlays.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 sound/soc/codecs/wm8804-i2c.c | 15 ++++++++++++++-
 1 file changed, 14 insertions(+), 1 deletion(-)

diff --git a/sound/soc/codecs/wm8804-i2c.c b/sound/soc/codecs/wm8804-i2c.c
index f27464c2c5ba..79541960f45d 100644
--- a/sound/soc/codecs/wm8804-i2c.c
+++ b/sound/soc/codecs/wm8804-i2c.c
@@ -13,6 +13,7 @@
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/i2c.h>
+#include <linux/acpi.h>
 
 #include "wm8804.h"
 
@@ -40,17 +41,29 @@ static const struct i2c_device_id wm8804_i2c_id[] = {
 };
 MODULE_DEVICE_TABLE(i2c, wm8804_i2c_id);
 
+#if defined(CONFIG_OF)
 static const struct of_device_id wm8804_of_match[] = {
 	{ .compatible = "wlf,wm8804", },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, wm8804_of_match);
+#endif
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id wm8804_acpi_match[] = {
+	{ "1AEC8804", 0 }, /* Wolfson PCI ID + part ID */
+	{ "10138804", 0 }, /* Cirrus Logic PCI ID + part ID */
+	{ },
+};
+MODULE_DEVICE_TABLE(acpi, wm8804_acpi_match);
+#endif
 
 static struct i2c_driver wm8804_i2c_driver = {
 	.driver = {
 		.name = "wm8804",
 		.pm = &wm8804_pm,
-		.of_match_table = wm8804_of_match,
+		.of_match_table = of_match_ptr(wm8804_of_match),
+		.acpi_match_table = ACPI_PTR(wm8804_acpi_match),
 	},
 	.probe = wm8804_i2c_probe,
 	.remove = wm8804_i2c_remove,
-- 
2.17.1

[PATCH AUTOSEL 4.9 02/14] ASoC: sigmadsp: safeload should not have lower byte limit

[Sasha Levin]

From: Danny Smith <danny.smith@axis.com>

[ Upstream commit 5ea752c6efdf5aa8a57aed816d453a8f479f1b0a ]

Fixed range in safeload conditional to allow safeload to up to 20 bytes,
without a lower limit.

Signed-off-by: Danny Smith <dannys@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 sound/soc/codecs/sigmadsp.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/sound/soc/codecs/sigmadsp.c b/sound/soc/codecs/sigmadsp.c
index d53680ac78e4..6df158669420 100644
--- a/sound/soc/codecs/sigmadsp.c
+++ b/sound/soc/codecs/sigmadsp.c
@@ -117,8 +117,7 @@ static int sigmadsp_ctrl_write(struct sigmadsp *sigmadsp,
 	struct sigmadsp_control *ctrl, void *data)
 {
 	/* safeload loads up to 20 bytes in a atomic operation */
-	if (ctrl->num_bytes > 4 && ctrl->num_bytes <= 20 && sigmadsp->ops &&
-	    sigmadsp->ops->safeload)
+	if (ctrl->num_bytes <= 20 && sigmadsp->ops && sigmadsp->ops->safeload)
 		return sigmadsp->ops->safeload(sigmadsp, ctrl->addr, data,
 			ctrl->num_bytes);
 	else
-- 
2.17.1

[PATCH AUTOSEL 4.9 03/14] selftests/efivarfs: add required kernel configs

[Sasha Levin]

From: Lei Yang <Lei.Yang@windriver.com>

[ Upstream commit 53cf59d6c0ad3edc4f4449098706a8f8986258b6 ]

add config file

Signed-off-by: Lei Yang <Lei.Yang@windriver.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 tools/testing/selftests/efivarfs/config | 1 +
 1 file changed, 1 insertion(+)
 create mode 100644 tools/testing/selftests/efivarfs/config

diff --git a/tools/testing/selftests/efivarfs/config b/tools/testing/selftests/efivarfs/config
new file mode 100644
index 000000000000..4e151f1005b2
--- /dev/null
+++ b/tools/testing/selftests/efivarfs/config
@@ -0,0 +1 @@
+CONFIG_EFIVAR_FS=y
-- 
2.17.1

[PATCH AUTOSEL 4.9 04/14] selftests: memory-hotplug: add required configs

[Sasha Levin]

From: Lei Yang <Lei.Yang@windriver.com>

[ Upstream commit 4d85af102a66ee6aeefa596f273169e77fb2b48e ]

add CONFIG_MEMORY_HOTREMOVE=y in config
without this config, /sys/devices/system/memory/memory*/removable
always return 0, I endup getting an early skip during test

Signed-off-by: Lei Yang <Lei.Yang@windriver.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 tools/testing/selftests/memory-hotplug/config | 1 +
 1 file changed, 1 insertion(+)

diff --git a/tools/testing/selftests/memory-hotplug/config b/tools/testing/selftests/memory-hotplug/config
index 2fde30191a47..a7e8cd5bb265 100644
--- a/tools/testing/selftests/memory-hotplug/config
+++ b/tools/testing/selftests/memory-hotplug/config
@@ -2,3 +2,4 @@ CONFIG_MEMORY_HOTPLUG=y
 CONFIG_MEMORY_HOTPLUG_SPARSE=y
 CONFIG_NOTIFIER_ERROR_INJECTION=y
 CONFIG_MEMORY_NOTIFIER_ERROR_INJECT=m
+CONFIG_MEMORY_HOTREMOVE=y
-- 
2.17.1

[PATCH AUTOSEL 4.9 05/14] mfd: omap-usb-host: Fix dts probe of children

[Sasha Levin]

From: Tony Lindgren <tony@atomide.com>

[ Upstream commit 10492ee8ed9188d6d420e1f79b2b9bdbc0624e65 ]

It currently only works if the parent bus uses "simple-bus". We
currently try to probe children with non-existing compatible values.
And we're missing .probe.

I noticed this while testing devices configured to probe using ti-sysc
interconnect target module driver. For that we also may want to rebind
the driver, so let's remove __init and __exit.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/mfd/omap-usb-host.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)

diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 7aab376ecb84..3785c638d530 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -548,8 +548,8 @@ static int usbhs_omap_get_dt_pdata(struct device *dev,
 }
 
 static const struct of_device_id usbhs_child_match_table[] = {
-	{ .compatible = "ti,omap-ehci", },
-	{ .compatible = "ti,omap-ohci", },
+	{ .compatible = "ti,ehci-omap", },
+	{ .compatible = "ti,ohci-omap3", },
 	{ }
 };
 
@@ -875,6 +875,7 @@ static struct platform_driver usbhs_omap_driver = {
 		.pm		= &usbhsomap_dev_pm_ops,
 		.of_match_table = usbhs_omap_dt_ids,
 	},
+	.probe		= usbhs_omap_probe,
 	.remove		= usbhs_omap_remove,
 };
 
@@ -884,9 +885,9 @@ MODULE_ALIAS("platform:" USBHS_DRIVER_NAME);
 MODULE_LICENSE("GPL v2");
 MODULE_DESCRIPTION("usb host common core driver for omap EHCI and OHCI");
 
-static int __init omap_usbhs_drvinit(void)
+static int omap_usbhs_drvinit(void)
 {
-	return platform_driver_probe(&usbhs_omap_driver, usbhs_omap_probe);
+	return platform_driver_register(&usbhs_omap_driver);
 }
 
 /*
@@ -898,7 +899,7 @@ static int __init omap_usbhs_drvinit(void)
  */
 fs_initcall_sync(omap_usbhs_drvinit);
 
-static void __exit omap_usbhs_drvexit(void)
+static void omap_usbhs_drvexit(void)
 {
 	platform_driver_unregister(&usbhs_omap_driver);
 }
-- 
2.17.1

[PATCH AUTOSEL 4.9 06/14] scsi: iscsi: target: Don't use stack buffer for scatterlist

[Sasha Levin]

From: Laura Abbott <labbott@redhat.com>

[ Upstream commit 679fcae46c8b2352bba3485d521da070cfbe68e6 ]

Fedora got a bug report of a crash with iSCSI:

kernel BUG at include/linux/scatterlist.h:143!
...
RIP: 0010:iscsit_do_crypto_hash_buf+0x154/0x180 [iscsi_target_mod]
...
 Call Trace:
  ? iscsi_target_tx_thread+0x200/0x200 [iscsi_target_mod]
  iscsit_get_rx_pdu+0x4cd/0xa90 [iscsi_target_mod]
  ? native_sched_clock+0x3e/0xa0
  ? iscsi_target_tx_thread+0x200/0x200 [iscsi_target_mod]
  iscsi_target_rx_thread+0x81/0xf0 [iscsi_target_mod]
  kthread+0x120/0x140
  ? kthread_create_worker_on_cpu+0x70/0x70
  ret_from_fork+0x3a/0x50

This is a BUG_ON for using a stack buffer with a scatterlist.  There
are two cases that trigger this bug. Switch to using a dynamically
allocated buffer for one case and do not assign a NULL buffer in
another case.

Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/target/iscsi/iscsi_target.c | 22 ++++++++++++++--------
 1 file changed, 14 insertions(+), 8 deletions(-)

diff --git a/drivers/target/iscsi/iscsi_target.c b/drivers/target/iscsi/iscsi_target.c
index 04d2b6e25503..80205f3362d4 100644
--- a/drivers/target/iscsi/iscsi_target.c
+++ b/drivers/target/iscsi/iscsi_target.c
@@ -1435,7 +1435,8 @@ static void iscsit_do_crypto_hash_buf(
 
 	sg_init_table(sg, ARRAY_SIZE(sg));
 	sg_set_buf(sg, buf, payload_length);
-	sg_set_buf(sg + 1, pad_bytes, padding);
+	if (padding)
+		sg_set_buf(sg + 1, pad_bytes, padding);
 
 	ahash_request_set_crypt(hash, sg, data_crc, payload_length + padding);
 
@@ -3949,10 +3950,14 @@ static bool iscsi_target_check_conn_state(struct iscsi_conn *conn)
 static void iscsit_get_rx_pdu(struct iscsi_conn *conn)
 {
 	int ret;
-	u8 buffer[ISCSI_HDR_LEN], opcode;
+	u8 *buffer, opcode;
 	u32 checksum = 0, digest = 0;
 	struct kvec iov;
 
+	buffer = kcalloc(ISCSI_HDR_LEN, sizeof(*buffer), GFP_KERNEL);
+	if (!buffer)
+		return;
+
 	while (!kthread_should_stop()) {
 		/*
 		 * Ensure that both TX and RX per connection kthreads
@@ -3960,7 +3965,6 @@ static void iscsit_get_rx_pdu(struct iscsi_conn *conn)
 		 */
 		iscsit_thread_check_cpumask(conn, current, 0);
 
-		memset(buffer, 0, ISCSI_HDR_LEN);
 		memset(&iov, 0, sizeof(struct kvec));
 
 		iov.iov_base	= buffer;
@@ -3969,7 +3973,7 @@ static void iscsit_get_rx_pdu(struct iscsi_conn *conn)
 		ret = rx_data(conn, &iov, 1, ISCSI_HDR_LEN);
 		if (ret != ISCSI_HDR_LEN) {
 			iscsit_rx_thread_wait_for_tcp(conn);
-			return;
+			break;
 		}
 
 		if (conn->conn_ops->HeaderDigest) {
@@ -3979,7 +3983,7 @@ static void iscsit_get_rx_pdu(struct iscsi_conn *conn)
 			ret = rx_data(conn, &iov, 1, ISCSI_CRC_LEN);
 			if (ret != ISCSI_CRC_LEN) {
 				iscsit_rx_thread_wait_for_tcp(conn);
-				return;
+				break;
 			}
 
 			iscsit_do_crypto_hash_buf(conn->conn_rx_hash,
@@ -4003,7 +4007,7 @@ static void iscsit_get_rx_pdu(struct iscsi_conn *conn)
 		}
 
 		if (conn->conn_state == TARG_CONN_STATE_IN_LOGOUT)
-			return;
+			break;
 
 		opcode = buffer[0] & ISCSI_OPCODE_MASK;
 
@@ -4014,13 +4018,15 @@ static void iscsit_get_rx_pdu(struct iscsi_conn *conn)
 			" while in Discovery Session, rejecting.\n", opcode);
 			iscsit_add_reject(conn, ISCSI_REASON_PROTOCOL_ERROR,
 					  buffer);
-			return;
+			break;
 		}
 
 		ret = iscsi_target_rx_opcode(conn, buffer);
 		if (ret < 0)
-			return;
+			break;
 	}
+
+	kfree(buffer);
 }
 
 int iscsi_target_rx_thread(void *arg)
-- 
2.17.1

[PATCH AUTOSEL 4.9 07/14] scsi: qla2xxx: Fix an endian bug in fcpcmd_is_corrupted()

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit cbe3fd39d223f14b1c60c80fe9347a3dd08c2edb ]

We should first do the le16_to_cpu endian conversion and then apply the
FCP_CMD_LENGTH_MASK mask.

Fixes: 5f35509db179 ("qla2xxx: Terminate exchange if corrupted")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Quinn Tran <Quinn.Tran@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/scsi/qla2xxx/qla_target.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/qla2xxx/qla_target.h b/drivers/scsi/qla2xxx/qla_target.h
index 0824a8164a24..07ea4fcf4f88 100644
--- a/drivers/scsi/qla2xxx/qla_target.h
+++ b/drivers/scsi/qla2xxx/qla_target.h
@@ -440,8 +440,8 @@ struct atio_from_isp {
 static inline int fcpcmd_is_corrupted(struct atio *atio)
 {
 	if (atio->entry_type == ATIO_TYPE7 &&
-	    (le16_to_cpu(atio->attr_n_length & FCP_CMD_LENGTH_MASK) <
-	    FCP_CMD_LENGTH_MIN))
+	    ((le16_to_cpu(atio->attr_n_length) & FCP_CMD_LENGTH_MASK) <
+	     FCP_CMD_LENGTH_MIN))
 		return 1;
 	else
 		return 0;
-- 
2.17.1

[PATCH AUTOSEL 4.9 08/14] sound: enable interrupt after dma buffer initialization

[Sasha Levin]

From: Yu Zhao <yuzhao@google.com>

[ Upstream commit b61749a89f826eb61fc59794d9e4697bd246eb61 ]

In snd_hdac_bus_init_chip(), we enable interrupt before
snd_hdac_bus_init_cmd_io() initializing dma buffers. If irq has
been acquired and irq handler uses the dma buffer, kernel may crash
when interrupt comes in.

Fix the problem by postponing enabling irq after dma buffer
initialization. And warn once on null dma buffer pointer during the
initialization.

Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 sound/hda/hdac_controller.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/sound/hda/hdac_controller.c b/sound/hda/hdac_controller.c
index 8761877207ec..00c6af2ae1c2 100644
--- a/sound/hda/hdac_controller.c
+++ b/sound/hda/hdac_controller.c
@@ -40,6 +40,8 @@ static void azx_clear_corbrp(struct hdac_bus *bus)
  */
 void snd_hdac_bus_init_cmd_io(struct hdac_bus *bus)
 {
+	WARN_ON_ONCE(!bus->rb.area);
+
 	spin_lock_irq(&bus->reg_lock);
 	/* CORB set up */
 	bus->corb.addr = bus->rb.addr;
@@ -478,13 +480,15 @@ bool snd_hdac_bus_init_chip(struct hdac_bus *bus, bool full_reset)
 	/* reset controller */
 	azx_reset(bus, full_reset);
 
-	/* initialize interrupts */
+	/* clear interrupts */
 	azx_int_clear(bus);
-	azx_int_enable(bus);
 
 	/* initialize the codec command I/O */
 	snd_hdac_bus_init_cmd_io(bus);
 
+	/* enable interrupts after CORB/RIRB buffers are initialized above */
+	azx_int_enable(bus);
+
 	/* program the position buffer */
 	if (bus->use_posbuf && bus->posbuf.addr) {
 		snd_hdac_chip_writel(bus, DPLBASE, (u32)bus->posbuf.addr);
-- 
2.17.1

[PATCH AUTOSEL 4.9 09/14] stmmac: fix valid numbers of unicast filter entries

[Sasha Levin]

From: Jongsung Kim <neidhard.kim@lge.com>

[ Upstream commit edf2ef7242805e53ec2e0841db26e06d8bc7da70 ]

Synopsys DWC Ethernet MAC can be configured to have 1..32, 64, or
128 unicast filter entries. (Table 7-8 MAC Address Registers from
databook) Fix dwmac1000_validate_ucast_entries() to accept values
between 1 and 32 in addition.

Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 890e4b083f4f..2019e163e0e9 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -71,7 +71,7 @@ static int dwmac1000_validate_mcast_bins(int mcast_bins)
  * Description:
  * This function validates the number of Unicast address entries supported
  * by a particular Synopsys 10/100/1000 controller. The Synopsys controller
- * supports 1, 32, 64, or 128 Unicast filter entries for it's Unicast filter
+ * supports 1..32, 64, or 128 Unicast filter entries for it's Unicast filter
  * logic. This function validates a valid, supported configuration is
  * selected, and defaults to 1 Unicast address if an unsupported
  * configuration is selected.
@@ -81,8 +81,7 @@ static int dwmac1000_validate_ucast_entries(int ucast_entries)
 	int x = ucast_entries;
 
 	switch (x) {
-	case 1:
-	case 32:
+	case 1 ... 32:
 	case 64:
 	case 128:
 		break;
-- 
2.17.1

[PATCH AUTOSEL 4.9 10/14] net: macb: disable scatter-gather for macb on sama5d3

[Sasha Levin]

From: Nicolas Ferre <nicolas.ferre@microchip.com>

[ Upstream commit eb4ed8e2d7fecb5f40db38e4498b9ee23cddf196 ]

Create a new configuration for the sama5d3-macb new compatibility string.
This configuration disables scatter-gather because we experienced lock down
of the macb interface of this particular SoC under very high load.

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/net/ethernet/cadence/macb.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/net/ethernet/cadence/macb.c b/drivers/net/ethernet/cadence/macb.c
index ec09fcece711..c4ccbb4453f2 100644
--- a/drivers/net/ethernet/cadence/macb.c
+++ b/drivers/net/ethernet/cadence/macb.c
@@ -2861,6 +2861,13 @@ static const struct macb_config at91sam9260_config = {
 	.init = macb_init,
 };
 
+static const struct macb_config sama5d3macb_config = {
+	.caps = MACB_CAPS_SG_DISABLED
+	      | MACB_CAPS_USRIO_HAS_CLKEN | MACB_CAPS_USRIO_DEFAULT_IS_MII_GMII,
+	.clk_init = macb_clk_init,
+	.init = macb_init,
+};
+
 static const struct macb_config pc302gem_config = {
 	.caps = MACB_CAPS_SG_DISABLED | MACB_CAPS_GIGABIT_MODE_AVAILABLE,
 	.dma_burst_length = 16,
@@ -2925,6 +2932,7 @@ static const struct of_device_id macb_dt_ids[] = {
 	{ .compatible = "cdns,gem", .data = &pc302gem_config },
 	{ .compatible = "atmel,sama5d2-gem", .data = &sama5d2_config },
 	{ .compatible = "atmel,sama5d3-gem", .data = &sama5d3_config },
+	{ .compatible = "atmel,sama5d3-macb", .data = &sama5d3macb_config },
 	{ .compatible = "atmel,sama5d4-gem", .data = &sama5d4_config },
 	{ .compatible = "cdns,at91rm9200-emac", .data = &emac_config },
 	{ .compatible = "cdns,emac", .data = &emac_config },
-- 
2.17.1

[PATCH AUTOSEL 4.9 11/14] ARM: dts: at91: add new compatibility string for macb on sama5d3

[Sasha Levin]

From: Nicolas Ferre <nicolas.ferre@microchip.com>

[ Upstream commit 321cc359d899a8e988f3725d87c18a628e1cc624 ]

We need this new compatibility string as we experienced different behavior
for this 10/100Mbits/s macb interface on this particular SoC.
Backward compatibility is preserved as we keep the alternative strings.

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 Documentation/devicetree/bindings/net/macb.txt | 1 +
 arch/arm/boot/dts/sama5d3_emac.dtsi            | 2 +-
 2 files changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt
index 1506e948610c..d1f435c92912 100644
--- a/Documentation/devicetree/bindings/net/macb.txt
+++ b/Documentation/devicetree/bindings/net/macb.txt
@@ -10,6 +10,7 @@ Required properties:
   Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on
   the Cadence GEM, or the generic form: "cdns,gem".
   Use "atmel,sama5d2-gem" for the GEM IP (10/100) available on Atmel sama5d2 SoCs.
+  Use "atmel,sama5d3-macb" for the 10/100Mbit IP available on Atmel sama5d3 SoCs.
   Use "atmel,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs.
   Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs.
   Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC.
diff --git a/arch/arm/boot/dts/sama5d3_emac.dtsi b/arch/arm/boot/dts/sama5d3_emac.dtsi
index 7cb235ef0fb6..6e9e1c2f9def 100644
--- a/arch/arm/boot/dts/sama5d3_emac.dtsi
+++ b/arch/arm/boot/dts/sama5d3_emac.dtsi
@@ -41,7 +41,7 @@
 			};
 
 			macb1: ethernet@f802c000 {
-				compatible = "cdns,at91sam9260-macb", "cdns,macb";
+				compatible = "atmel,sama5d3-macb", "cdns,at91sam9260-macb", "cdns,macb";
 				reg = <0xf802c000 0x100>;
 				interrupts = <35 IRQ_TYPE_LEVEL_HIGH 3>;
 				pinctrl-names = "default";
-- 
2.17.1

[PATCH AUTOSEL 4.9 12/14] x86/kvm/lapic: always disable MMIO interface in x2APIC mode

[Sasha Levin]

From: Vitaly Kuznetsov <vkuznets@redhat.com>

[ Upstream commit d1766202779e81d0f2a94c4650a6ba31497d369d ]

When VMX is used with flexpriority disabled (because of no support or
if disabled with module parameter) MMIO interface to lAPIC is still
available in x2APIC mode while it shouldn't be (kvm-unit-tests):

PASS: apic_disable: Local apic enabled in x2APIC mode
PASS: apic_disable: CPUID.1H:EDX.APIC[bit 9] is set
FAIL: apic_disable: *0xfee00030: 50014

The issue appears because we basically do nothing while switching to
x2APIC mode when APIC access page is not used. apic_mmio_{read,write}
only check if lAPIC is disabled before proceeding to actual write.

When APIC access is virtualized we correctly manipulate with VMX controls
in vmx_set_virtual_apic_mode() and we don't get vmexits from memory writes
in x2APIC mode so there's no issue.

Disabling MMIO interface seems to be easy. The question is: what do we
do with these reads and writes? If we add apic_x2apic_mode() check to
apic_mmio_in_range() and return -EOPNOTSUPP these reads and writes will
go to userspace. When lAPIC is in kernel, Qemu uses this interface to
inject MSIs only (see kvm_apic_mem_write() in hw/i386/kvm/apic.c). This
somehow works with disabled lAPIC but when we're in xAPIC mode we will
get a real injected MSI from every write to lAPIC. Not good.

The simplest solution seems to be to just ignore writes to the region
and return ~0 for all reads when we're in x2APIC mode. This is what this
patch does. However, this approach is inconsistent with what currently
happens when flexpriority is enabled: we allocate APIC access page and
create KVM memory region so in x2APIC modes all reads and writes go to
this pre-allocated page which is, btw, the same for all vCPUs.

Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 arch/x86/include/uapi/asm/kvm.h |  1 +
 arch/x86/kvm/lapic.c            | 22 +++++++++++++++++++---
 2 files changed, 20 insertions(+), 3 deletions(-)

diff --git a/arch/x86/include/uapi/asm/kvm.h b/arch/x86/include/uapi/asm/kvm.h
index 739c0c594022..1bb90fafcdc3 100644
--- a/arch/x86/include/uapi/asm/kvm.h
+++ b/arch/x86/include/uapi/asm/kvm.h
@@ -356,5 +356,6 @@ struct kvm_sync_regs {
 
 #define KVM_X86_QUIRK_LINT0_REENABLED	(1 << 0)
 #define KVM_X86_QUIRK_CD_NW_CLEARED	(1 << 1)
+#define KVM_X86_QUIRK_LAPIC_MMIO_HOLE	(1 << 2)
 
 #endif /* _ASM_X86_KVM_H */
diff --git a/arch/x86/kvm/lapic.c b/arch/x86/kvm/lapic.c
index a8a86be8cf15..69a81a7daa24 100644
--- a/arch/x86/kvm/lapic.c
+++ b/arch/x86/kvm/lapic.c
@@ -1220,9 +1220,8 @@ EXPORT_SYMBOL_GPL(kvm_lapic_reg_read);
 
 static int apic_mmio_in_range(struct kvm_lapic *apic, gpa_t addr)
 {
-	return kvm_apic_hw_enabled(apic) &&
-	    addr >= apic->base_address &&
-	    addr < apic->base_address + LAPIC_MMIO_LENGTH;
+	return addr >= apic->base_address &&
+		addr < apic->base_address + LAPIC_MMIO_LENGTH;
 }
 
 static int apic_mmio_read(struct kvm_vcpu *vcpu, struct kvm_io_device *this,
@@ -1234,6 +1233,15 @@ static int apic_mmio_read(struct kvm_vcpu *vcpu, struct kvm_io_device *this,
 	if (!apic_mmio_in_range(apic, address))
 		return -EOPNOTSUPP;
 
+	if (!kvm_apic_hw_enabled(apic) || apic_x2apic_mode(apic)) {
+		if (!kvm_check_has_quirk(vcpu->kvm,
+					 KVM_X86_QUIRK_LAPIC_MMIO_HOLE))
+			return -EOPNOTSUPP;
+
+		memset(data, 0xff, len);
+		return 0;
+	}
+
 	kvm_lapic_reg_read(apic, offset, len, data);
 
 	return 0;
@@ -1646,6 +1654,14 @@ static int apic_mmio_write(struct kvm_vcpu *vcpu, struct kvm_io_device *this,
 	if (!apic_mmio_in_range(apic, address))
 		return -EOPNOTSUPP;
 
+	if (!kvm_apic_hw_enabled(apic) || apic_x2apic_mode(apic)) {
+		if (!kvm_check_has_quirk(vcpu->kvm,
+					 KVM_X86_QUIRK_LAPIC_MMIO_HOLE))
+			return -EOPNOTSUPP;
+
+		return 0;
+	}
+
 	/*
 	 * APIC register must be aligned on 128-bits boundary.
 	 * 32/64/128 bits registers must be accessed thru 32 bits.
-- 
2.17.1

[PATCH AUTOSEL 4.9 13/14] drm/amdgpu: Fix SDMA HQD destroy error on gfx_v7

[Sasha Levin]

From: Amber Lin <Amber.Lin@amd.com>

[ Upstream commit caaa4c8a6be2a275bd14f2369ee364978ff74704 ]

A wrong register bit was examinated for checking SDMA status so it reports
false failures. This typo only appears on gfx_v7. gfx_v8 checks the correct
bit.

Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gfx_v7.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gfx_v7.c b/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gfx_v7.c
index 47951f4775b9..d47c32a18da8 100644
--- a/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gfx_v7.c
+++ b/drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_gfx_v7.c
@@ -505,7 +505,7 @@ static int kgd_hqd_sdma_destroy(struct kgd_dev *kgd, void *mqd,
 
 	while (true) {
 		temp = RREG32(sdma_base_addr + mmSDMA0_RLC0_CONTEXT_STATUS);
-		if (temp & SDMA0_STATUS_REG__RB_CMD_IDLE__SHIFT)
+		if (temp & SDMA0_RLC0_CONTEXT_STATUS__IDLE_MASK)
 			break;
 		if (timeout <= 0)
 			return -ETIME;
-- 
2.17.1

[PATCH AUTOSEL 4.9 14/14] ubifs: Check for name being NULL while mounting

[Sasha Levin]

From: Richard Weinberger <richard@nod.at>

[ Upstream commit 37f31b6ca4311b94d985fb398a72e5399ad57925 ]

The requested device name can be NULL or an empty string.
Check for that and refuse to continue. UBIFS has to do this manually
since we cannot use mount_bdev(), which checks for this condition.

Fixes: 1e51764a3c2ac ("UBIFS: add new flash file system")
Reported-by: syzbot+38bd0f7865e5c6379280@syzkaller.appspotmail.com
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 fs/ubifs/super.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/fs/ubifs/super.c b/fs/ubifs/super.c
index 03dda1cbe485..727a9e3fa806 100644
--- a/fs/ubifs/super.c
+++ b/fs/ubifs/super.c
@@ -1918,6 +1918,9 @@ static struct ubi_volume_desc *open_ubi(const char *name, int mode)
 	int dev, vol;
 	char *endptr;
 
+	if (!name || !*name)
+		return ERR_PTR(-EINVAL);
+
 	/* First, try to open using the device node path method */
 	ubi = ubi_open_volume_path(name, mode);
 	if (!IS_ERR(ubi))
-- 
2.17.1