All of lore.kernel.org
 help / color / mirror / Atom feed
From: Jagan Teki <jagan@amarulasolutions.com>
To: Maxime Ripard <maxime.ripard@bootlin.com>,
	Chen-Yu Tsai <wens@csie.org>, Icenowy Zheng <icenowy@aosc.io>,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.com
Cc: Jagan Teki <jagan@openedev.com>
Subject: [RFC PATCH 7/7] arm64: allwinner: h6: orangepi-liet2: Enable AP6356S WiFi support
Date: Thu,  1 Nov 2018 00:06:34 +0530	[thread overview]
Message-ID: <20181031183634.29640-7-jagan@amarulasolutions.com> (raw)
In-Reply-To: <20181031183634.29640-1-jagan@amarulasolutions.com>

From: Jagan Teki <jagan@openedev.com>

Enable AP6356S WiFi/BT combo chip on Orangepi Lite2 board:
- WiFi SDIO interface is connected to MMC1
- WiFi WL-PMU-EN pin connected to gpio PM3: attach to mmc-pwrseq
- WiFi WL-WAKE-AP pin connected to gpio PM0
- 32kHz external oscillator gate clock from RTC

Signed-off-by: Jagan Teki <jagan@openedev.com>
---
Note:
- chip detected, but failed to connect
[  129.084504] brcmfmac: brcmf_sdio_hostmail: mailbox indicates firmware halted
[  135.906409] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout 

 .../allwinner/sun50i-h6-orangepi-lite2.dts    | 27 +++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts
index e098a2475f2d..b8012208c185 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts
@@ -8,4 +8,31 @@
 / {
 	model = "OrangePi Lite2";
 	compatible = "xunlong,orangepi-lite2", "allwinner,sun50i-h6";
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* WL-REG-ON: PM3 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_cldo2>;
+	vqmmc-supply = <&reg_bldo3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>;	/* WL-WAKE-AP: PM0 */
+		interrupt-names = "host-wake";
+	};
 };
-- 
2.18.0.321.gffc6fa0e3


WARNING: multiple messages have this Message-ID (diff)
From: jagan@amarulasolutions.com (Jagan Teki)
To: linux-arm-kernel@lists.infradead.org
Subject: [RFC PATCH 7/7] arm64: allwinner: h6: orangepi-liet2: Enable AP6356S WiFi support
Date: Thu,  1 Nov 2018 00:06:34 +0530	[thread overview]
Message-ID: <20181031183634.29640-7-jagan@amarulasolutions.com> (raw)
In-Reply-To: <20181031183634.29640-1-jagan@amarulasolutions.com>

From: Jagan Teki <jagan@openedev.com>

Enable AP6356S WiFi/BT combo chip on Orangepi Lite2 board:
- WiFi SDIO interface is connected to MMC1
- WiFi WL-PMU-EN pin connected to gpio PM3: attach to mmc-pwrseq
- WiFi WL-WAKE-AP pin connected to gpio PM0
- 32kHz external oscillator gate clock from RTC

Signed-off-by: Jagan Teki <jagan@openedev.com>
---
Note:
- chip detected, but failed to connect
[  129.084504] brcmfmac: brcmf_sdio_hostmail: mailbox indicates firmware halted
[  135.906409] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout 

 .../allwinner/sun50i-h6-orangepi-lite2.dts    | 27 +++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts
index e098a2475f2d..b8012208c185 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts
@@ -8,4 +8,31 @@
 / {
 	model = "OrangePi Lite2";
 	compatible = "xunlong,orangepi-lite2", "allwinner,sun50i-h6";
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* WL-REG-ON: PM3 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_cldo2>;
+	vqmmc-supply = <&reg_bldo3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>;	/* WL-WAKE-AP: PM0 */
+		interrupt-names = "host-wake";
+	};
 };
-- 
2.18.0.321.gffc6fa0e3

  parent reply	other threads:[~2018-10-31 18:37 UTC|newest]

Thread overview: 59+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-10-31 18:36 [PATCH 1/7] clk: sunxi-ng: sun50i: h6: Fix MMC clock mux width Jagan Teki
2018-10-31 18:36 ` Jagan Teki
2018-10-31 18:36 ` [PATCH 2/7] arm64: allwinner: h6: Add common orangepi nodes into dtsi Jagan Teki
2018-10-31 18:36   ` Jagan Teki
2018-10-31 18:36   ` Jagan Teki
2018-11-01  2:53   ` Chen-Yu Tsai
2018-11-01  2:53     ` Chen-Yu Tsai
2018-11-01  2:53     ` Chen-Yu Tsai
2018-11-01  7:13     ` Jagan Teki
2018-11-01  7:13       ` Jagan Teki
2018-11-01  7:13       ` Jagan Teki
2018-11-01  7:20       ` Chen-Yu Tsai
2018-11-01  7:20         ` Chen-Yu Tsai
2018-11-01  7:20         ` Chen-Yu Tsai
2018-10-31 18:36 ` [PATCH 3/7] arm64: allwinner: h6: Add OrangePi Lite2 initial support Jagan Teki
2018-10-31 18:36   ` Jagan Teki
2018-10-31 18:36   ` Jagan Teki
2018-10-31 18:36 ` [PATCH 4/7] arm64: allwinner: h6: Add MMC1 pinmux Jagan Teki
2018-10-31 18:36   ` Jagan Teki
2018-10-31 18:36   ` Jagan Teki
2018-10-31 18:36 ` [PATCH 5/7] arm64: allwinner: h6: Add RTC node Jagan Teki
2018-10-31 18:36   ` Jagan Teki
2018-11-01  2:55   ` Chen-Yu Tsai
2018-11-01  2:55     ` Chen-Yu Tsai
2018-11-01  2:55     ` Chen-Yu Tsai
2018-11-01  7:33     ` Jagan Teki
2018-11-01  7:33       ` Jagan Teki
2018-11-01  7:33       ` Jagan Teki
2018-11-01  7:53       ` Chen-Yu Tsai
2018-11-01  7:53         ` Chen-Yu Tsai
2018-11-01  7:53         ` Chen-Yu Tsai
2018-11-01  9:02         ` Jagan Teki
2018-11-01  9:02           ` Jagan Teki
2018-11-01  9:02           ` Jagan Teki
2018-11-01  9:35           ` Chen-Yu Tsai
2018-11-01  9:35             ` Chen-Yu Tsai
2018-11-01  9:35             ` Chen-Yu Tsai
2018-10-31 18:36 ` [PATCH 6/7] arm64: allwinner: h6: Add RTC clock to phandle 32kHz external oscillator Jagan Teki
2018-10-31 18:36   ` Jagan Teki
2018-10-31 18:36   ` Jagan Teki
2018-11-01  2:57   ` Chen-Yu Tsai
2018-11-01  2:57     ` Chen-Yu Tsai
2018-11-01  2:57     ` Chen-Yu Tsai
2018-10-31 18:36 ` Jagan Teki [this message]
2018-10-31 18:36   ` [RFC PATCH 7/7] arm64: allwinner: h6: orangepi-liet2: Enable AP6356S WiFi support Jagan Teki
2018-11-01  7:35   ` Jagan Teki
2018-11-01  7:35     ` Jagan Teki
2018-11-01  7:35     ` Jagan Teki
2018-11-01  7:58     ` Chen-Yu Tsai
2018-11-01  7:58       ` Chen-Yu Tsai
2018-11-01  7:58       ` Chen-Yu Tsai
2018-11-01  9:08       ` Jagan Teki
2018-11-01  9:08         ` Jagan Teki
2018-11-01  9:08         ` Jagan Teki
2018-11-01  9:49         ` Chen-Yu Tsai
2018-11-01  9:49           ` Chen-Yu Tsai
2018-11-01  9:49           ` Chen-Yu Tsai
2018-11-05  8:41 ` [PATCH 1/7] clk: sunxi-ng: sun50i: h6: Fix MMC clock mux width Maxime Ripard
2018-11-05  8:41   ` Maxime Ripard

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20181031183634.29640-7-jagan@amarulasolutions.com \
    --to=jagan@amarulasolutions.com \
    --cc=devicetree@vger.kernel.org \
    --cc=icenowy@aosc.io \
    --cc=jagan@openedev.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-sunxi@googlegroups.com \
    --cc=maxime.ripard@bootlin.com \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.