* [PATCH] tty: serial: 8250_mtk: always resume the device in probe.
@ 2018-11-27 4:49 ` Peter Shih
0 siblings, 0 replies; 3+ messages in thread
From: Peter Shih @ 2018-11-27 4:49 UTC (permalink / raw)
Cc: pihsun, Greg Kroah-Hartman, Jiri Slaby, Matthias Brugger,
linux-serial, linux-arm-kernel, linux-mediatek, linux-kernel
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a255a ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling")
Signed-off-by: Peter Shih <pihsun@chromium.org>
---
drivers/tty/serial/8250/8250_mtk.c | 16 +++++++---------
1 file changed, 7 insertions(+), 9 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index dd5e1cede2b58..c3f933d10295e 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -213,17 +213,17 @@ static int mtk8250_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, data);
- pm_runtime_enable(&pdev->dev);
- if (!pm_runtime_enabled(&pdev->dev)) {
- err = mtk8250_runtime_resume(&pdev->dev);
- if (err)
- return err;
- }
+ err = mtk8250_runtime_resume(&pdev->dev);
+ if (err)
+ return err;
data->line = serial8250_register_8250_port(&uart);
if (data->line < 0)
return data->line;
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+
return 0;
}
@@ -234,13 +234,11 @@ static int mtk8250_remove(struct platform_device *pdev)
pm_runtime_get_sync(&pdev->dev);
serial8250_unregister_port(data->line);
+ mtk8250_runtime_suspend(&pdev->dev);
pm_runtime_disable(&pdev->dev);
pm_runtime_put_noidle(&pdev->dev);
- if (!pm_runtime_status_suspended(&pdev->dev))
- mtk8250_runtime_suspend(&pdev->dev);
-
return 0;
}
--
2.20.0.rc0.387.gc7a69e6b6c-goog
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH] tty: serial: 8250_mtk: always resume the device in probe.
@ 2018-11-27 4:49 ` Peter Shih
0 siblings, 0 replies; 3+ messages in thread
From: Peter Shih @ 2018-11-27 4:49 UTC (permalink / raw)
Cc: pihsun, Greg Kroah-Hartman, Jiri Slaby, Matthias Brugger,
linux-serial, linux-arm-kernel, linux-mediatek, linux-kernel
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a255a ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling")
Signed-off-by: Peter Shih <pihsun@chromium.org>
---
drivers/tty/serial/8250/8250_mtk.c | 16 +++++++---------
1 file changed, 7 insertions(+), 9 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index dd5e1cede2b58..c3f933d10295e 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -213,17 +213,17 @@ static int mtk8250_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, data);
- pm_runtime_enable(&pdev->dev);
- if (!pm_runtime_enabled(&pdev->dev)) {
- err = mtk8250_runtime_resume(&pdev->dev);
- if (err)
- return err;
- }
+ err = mtk8250_runtime_resume(&pdev->dev);
+ if (err)
+ return err;
data->line = serial8250_register_8250_port(&uart);
if (data->line < 0)
return data->line;
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+
return 0;
}
@@ -234,13 +234,11 @@ static int mtk8250_remove(struct platform_device *pdev)
pm_runtime_get_sync(&pdev->dev);
serial8250_unregister_port(data->line);
+ mtk8250_runtime_suspend(&pdev->dev);
pm_runtime_disable(&pdev->dev);
pm_runtime_put_noidle(&pdev->dev);
- if (!pm_runtime_status_suspended(&pdev->dev))
- mtk8250_runtime_suspend(&pdev->dev);
-
return 0;
}
--
2.20.0.rc0.387.gc7a69e6b6c-goog
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH] tty: serial: 8250_mtk: always resume the device in probe.
@ 2018-11-27 4:49 ` Peter Shih
0 siblings, 0 replies; 3+ messages in thread
From: Peter Shih @ 2018-11-27 4:49 UTC (permalink / raw)
To: linux-arm-kernel
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a255a ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling")
Signed-off-by: Peter Shih <pihsun@chromium.org>
---
drivers/tty/serial/8250/8250_mtk.c | 16 +++++++---------
1 file changed, 7 insertions(+), 9 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index dd5e1cede2b58..c3f933d10295e 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -213,17 +213,17 @@ static int mtk8250_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, data);
- pm_runtime_enable(&pdev->dev);
- if (!pm_runtime_enabled(&pdev->dev)) {
- err = mtk8250_runtime_resume(&pdev->dev);
- if (err)
- return err;
- }
+ err = mtk8250_runtime_resume(&pdev->dev);
+ if (err)
+ return err;
data->line = serial8250_register_8250_port(&uart);
if (data->line < 0)
return data->line;
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+
return 0;
}
@@ -234,13 +234,11 @@ static int mtk8250_remove(struct platform_device *pdev)
pm_runtime_get_sync(&pdev->dev);
serial8250_unregister_port(data->line);
+ mtk8250_runtime_suspend(&pdev->dev);
pm_runtime_disable(&pdev->dev);
pm_runtime_put_noidle(&pdev->dev);
- if (!pm_runtime_status_suspended(&pdev->dev))
- mtk8250_runtime_suspend(&pdev->dev);
-
return 0;
}
--
2.20.0.rc0.387.gc7a69e6b6c-goog
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2018-11-27 4:50 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-11-27 4:49 [PATCH] tty: serial: 8250_mtk: always resume the device in probe Peter Shih
2018-11-27 4:49 ` Peter Shih
2018-11-27 4:49 ` Peter Shih
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.