[CI v13 01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state

[CI v13 01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state

[Manasi Navare]

Basic DSC parameters and DSC configuration data needs to be computed
for each of the requested mode during atomic check. This is
required since for certain modes, valid DSC parameters and config
data might not be computed in which case compression cannot be
enabled for that mode.
For that reason we need to add these params and config structure
to the intel_crtc_state so that if valid this state information
can directly be used while enabling DSC in atomic commit.

v2:
* Rebase on drm-tip (Manasi)

Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h  | 1 +
 drivers/gpu/drm/i915/intel_drv.h | 9 +++++++++
 2 files changed, 10 insertions(+)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index f763b30f98d9..183aae996305 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -53,6 +53,7 @@
 #include <drm/drm_auth.h>
 #include <drm/drm_cache.h>
 #include <drm/drm_util.h>
+#include <drm/drm_dsc.h>
 
 #include "i915_fixed.h"
 #include "i915_params.h"
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index a62d77b76291..270212fa43a0 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -937,6 +937,15 @@ struct intel_crtc_state {
 
 	/* Output down scaling is done in LSPCON device */
 	bool lspcon_downsampling;
+
+	/* Display Stream compression state */
+	struct {
+		bool compression_enable;
+		bool dsc_split;
+		u16 compressed_bpp;
+		u8 slice_count;
+	} dsc_params;
+	struct drm_dsc_config dp_dsc_cfg;
 };
 
 struct intel_crtc {
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 02/17] drm/i915/dp: Compute DSC pipe config in atomic check

[Manasi Navare]

DSC params like the enable, compressed bpp, slice count and
dsc_split are added to the intel_crtc_state. These parameters
are set based on the requested mode and available link parameters
during the pipe configuration in atomic check phase.
These values are then later used to populate the remaining DSC
and RC parameters before enbaling DSC in atomic commit.

v14:
Remove leftovers, use dsc_bpc, refine dsc_compute_config (Ville)
v13:
* Compute DSC bpc only when DSC is req to be enabled (Ville)
v12:
* Override bpp with dsc dpcd color depth (Manasi)
v11:
* Const crtc_state, reject DSC on DP without FEC (Ville)
* Dont set dsc_split to false (Ville)
v10:
* Add a helper for dp_dsc support (Ville)
* Set pipe_config to max bpp, link params for DSC for now (Ville)
* Compute bpp - use dp dsc support helper (Ville)
v9:
* Rebase on top of drm-tip that now uses fast_narrow config
for edp (Manasi)
v8:
* Check for DSC bpc not 0 (manasi)

v7:
* Fix indentation in compute_m_n (Manasi)

v6 (From Gaurav):
* Remove function call of intel_dp_compute_dsc_params() and
invoke intel_dp_compute_dsc_params() in the patch where
it is defined to fix compilation warning (Gaurav)

v5:
Add drm_dsc_cfg in intel_crtc_state (Manasi)

v4:
* Rebase on refactoring of intel_dp_compute_config on tip (Manasi)
* Add a comment why we need to check PSR while enabling DSC (Gaurav)

v3:
* Check PPR > max_cdclock to use 2 VDSC instances (Ville)

v2:
* Add if-else for eDP/DP (Gaurav)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
---
 drivers/gpu/drm/i915/intel_display.c |   2 +-
 drivers/gpu/drm/i915/intel_display.h |   2 +-
 drivers/gpu/drm/i915/intel_dp.c      | 192 ++++++++++++++++++++++++---
 3 files changed, 172 insertions(+), 24 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index e9f4e22b2a4e..69bb0b75a806 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -6724,7 +6724,7 @@ static void compute_m_n(unsigned int m, unsigned int n,
 }
 
 void
-intel_link_compute_m_n(int bits_per_pixel, int nlanes,
+intel_link_compute_m_n(u16 bits_per_pixel, int nlanes,
 		       int pixel_clock, int link_clock,
 		       struct intel_link_m_n *m_n,
 		       bool constant_n)
diff --git a/drivers/gpu/drm/i915/intel_display.h b/drivers/gpu/drm/i915/intel_display.h
index 5f2955b944da..5e253f741d29 100644
--- a/drivers/gpu/drm/i915/intel_display.h
+++ b/drivers/gpu/drm/i915/intel_display.h
@@ -423,7 +423,7 @@ struct intel_link_m_n {
 	     (__i)++) \
 		for_each_if(plane)
 
-void intel_link_compute_m_n(int bpp, int nlanes,
+void intel_link_compute_m_n(u16 bpp, int nlanes,
 			    int pixel_clock, int link_clock,
 			    struct intel_link_m_n *m_n,
 			    bool constant_n);
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 70ae3d57316b..a2780733768a 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -47,6 +47,8 @@
 
 /* DP DSC small joiner has 2 FIFOs each of 640 x 6 bytes */
 #define DP_DSC_MAX_SMALL_JOINER_RAM_BUFFER	61440
+#define DP_DSC_MIN_SUPPORTED_BPC		8
+#define DP_DSC_MAX_SUPPORTED_BPC		10
 
 /* DP DSC throughput values used for slice count calculations KPixels/s */
 #define DP_DSC_PEAK_PIXEL_RATE			2720000
@@ -1708,6 +1710,26 @@ struct link_config_limits {
 	int min_bpp, max_bpp;
 };
 
+static bool intel_dp_source_supports_dsc(struct intel_dp *intel_dp,
+					 const struct intel_crtc_state *pipe_config)
+{
+	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
+
+	/* FIXME: FEC needed for external DP until then reject DSC on DP */
+	if (!intel_dp_is_edp(intel_dp))
+		return false;
+
+	return INTEL_GEN(dev_priv) >= 10 &&
+		pipe_config->cpu_transcoder != TRANSCODER_A;
+}
+
+static bool intel_dp_supports_dsc(struct intel_dp *intel_dp,
+				  const struct intel_crtc_state *pipe_config)
+{
+	return intel_dp_source_supports_dsc(intel_dp, pipe_config) &&
+		drm_dp_sink_supports_dsc(intel_dp->dsc_dpcd);
+}
+
 static int intel_dp_compute_bpp(struct intel_dp *intel_dp,
 				struct intel_crtc_state *pipe_config)
 {
@@ -1842,14 +1864,115 @@ intel_dp_compute_link_config_fast(struct intel_dp *intel_dp,
 	return false;
 }
 
+static int intel_dp_dsc_compute_bpp(struct intel_dp *intel_dp, u8 dsc_max_bpc)
+{
+	int i, num_bpc;
+	u8 dsc_bpc[3] = {0};
+
+	num_bpc = drm_dp_dsc_sink_supported_input_bpcs(intel_dp->dsc_dpcd,
+						       dsc_bpc);
+	for (i = 0; i < num_bpc; i++) {
+		if (dsc_max_bpc >= dsc_bpc[i])
+			return dsc_bpc[i] * 3;
+	}
+
+	return 0;
+}
+
+static bool intel_dp_dsc_compute_config(struct intel_dp *intel_dp,
+					struct intel_crtc_state *pipe_config,
+					struct drm_connector_state *conn_state,
+					struct link_config_limits *limits)
+{
+	struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
+	struct drm_i915_private *dev_priv = to_i915(dig_port->base.base.dev);
+	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
+	u8 dsc_max_bpc;
+	int pipe_bpp;
+
+	if (!intel_dp_supports_dsc(intel_dp, pipe_config))
+		return false;
+
+	dsc_max_bpc = min_t(u8, DP_DSC_MAX_SUPPORTED_BPC,
+			    conn_state->max_requested_bpc);
+
+	pipe_bpp = intel_dp_dsc_compute_bpp(intel_dp, dsc_max_bpc);
+	if (pipe_bpp < DP_DSC_MIN_SUPPORTED_BPC * 3) {
+		DRM_DEBUG_KMS("No DSC support for less than 8bpc\n");
+		return false;
+	}
+
+	/*
+	 * For now enable DSC for max bpp, max link rate, max lane count.
+	 * Optimize this later for the minimum possible link rate/lane count
+	 * with DSC enabled for the requested mode.
+	 */
+	pipe_config->pipe_bpp = pipe_bpp;
+	pipe_config->port_clock = intel_dp->common_rates[limits->max_clock];
+	pipe_config->lane_count = limits->max_lane_count;
+
+	if (intel_dp_is_edp(intel_dp)) {
+		pipe_config->dsc_params.compressed_bpp =
+			min_t(u16, drm_edp_dsc_sink_output_bpp(intel_dp->dsc_dpcd) >> 4,
+			      pipe_config->pipe_bpp);
+		pipe_config->dsc_params.slice_count =
+			drm_dp_dsc_sink_max_slice_count(intel_dp->dsc_dpcd,
+							true);
+	} else {
+		u16 dsc_max_output_bpp;
+		u8 dsc_dp_slice_count;
+
+		dsc_max_output_bpp =
+			intel_dp_dsc_get_output_bpp(pipe_config->port_clock,
+						    pipe_config->lane_count,
+						    adjusted_mode->crtc_clock,
+						    adjusted_mode->crtc_hdisplay);
+		dsc_dp_slice_count =
+			intel_dp_dsc_get_slice_count(intel_dp,
+						     adjusted_mode->crtc_clock,
+						     adjusted_mode->crtc_hdisplay);
+		if (!dsc_max_output_bpp || !dsc_dp_slice_count) {
+			DRM_DEBUG_KMS("Compressed BPP/Slice Count not supported\n");
+			return false;
+		}
+		pipe_config->dsc_params.compressed_bpp = min_t(u16,
+							       dsc_max_output_bpp >> 4,
+							       pipe_config->pipe_bpp);
+		pipe_config->dsc_params.slice_count = dsc_dp_slice_count;
+	}
+	/*
+	 * VDSC engine operates at 1 Pixel per clock, so if peak pixel rate
+	 * is greater than the maximum Cdclock and if slice count is even
+	 * then we need to use 2 VDSC instances.
+	 */
+	if (adjusted_mode->crtc_clock > dev_priv->max_cdclk_freq) {
+		if (pipe_config->dsc_params.slice_count > 1) {
+			pipe_config->dsc_params.dsc_split = true;
+		} else {
+			DRM_DEBUG_KMS("Cannot split stream to use 2 VDSC instances\n");
+			return false;
+		}
+	}
+	pipe_config->dsc_params.compression_enable = true;
+	DRM_DEBUG_KMS("DP DSC computed with Input Bpp = %d "
+		      "Compressed Bpp = %d Slice Count = %d\n",
+		      pipe_config->pipe_bpp,
+		      pipe_config->dsc_params.compressed_bpp,
+		      pipe_config->dsc_params.slice_count);
+
+	return true;
+}
+
 static bool
 intel_dp_compute_link_config(struct intel_encoder *encoder,
-			     struct intel_crtc_state *pipe_config)
+			     struct intel_crtc_state *pipe_config,
+			     struct drm_connector_state *conn_state)
 {
 	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
 	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
 	struct link_config_limits limits;
 	int common_len;
+	bool ret;
 
 	common_len = intel_dp_common_len_rate_limit(intel_dp,
 						    intel_dp->max_link_rate);
@@ -1888,7 +2011,7 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
 		      intel_dp->common_rates[limits.max_clock],
 		      limits.max_bpp, adjusted_mode->crtc_clock);
 
-	if (intel_dp_is_edp(intel_dp)) {
+	if (intel_dp_is_edp(intel_dp))
 		/*
 		 * Optimize for fast and narrow. eDP 1.3 section 3.3 and eDP 1.4
 		 * section A.1: "It is recommended that the minimum number of
@@ -1898,26 +2021,42 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
 		 * Note that we use the max clock and lane count for eDP 1.3 and
 		 * earlier, and fast vs. wide is irrelevant.
 		 */
-		if (!intel_dp_compute_link_config_fast(intel_dp, pipe_config,
-						       &limits))
-			return false;
-	} else {
+		ret = intel_dp_compute_link_config_fast(intel_dp, pipe_config,
+							&limits);
+	else
 		/* Optimize for slow and wide. */
-		if (!intel_dp_compute_link_config_wide(intel_dp, pipe_config,
-						       &limits))
+		ret = intel_dp_compute_link_config_wide(intel_dp, pipe_config,
+							&limits);
+
+	/* enable compression if the mode doesn't fit available BW */
+	if (!ret) {
+		if (!intel_dp_dsc_compute_config(intel_dp, pipe_config,
+						 conn_state, &limits))
 			return false;
 	}
 
-	DRM_DEBUG_KMS("DP lane count %d clock %d bpp %d\n",
-		      pipe_config->lane_count, pipe_config->port_clock,
-		      pipe_config->pipe_bpp);
+	if (pipe_config->dsc_params.compression_enable) {
+		DRM_DEBUG_KMS("DP lane count %d clock %d Input bpp %d Compressed bpp %d\n",
+			      pipe_config->lane_count, pipe_config->port_clock,
+			      pipe_config->pipe_bpp,
+			      pipe_config->dsc_params.compressed_bpp);
 
-	DRM_DEBUG_KMS("DP link rate required %i available %i\n",
-		      intel_dp_link_required(adjusted_mode->crtc_clock,
-					     pipe_config->pipe_bpp),
-		      intel_dp_max_data_rate(pipe_config->port_clock,
-					     pipe_config->lane_count));
+		DRM_DEBUG_KMS("DP link rate required %i available %i\n",
+			      intel_dp_link_required(adjusted_mode->crtc_clock,
+						     pipe_config->dsc_params.compressed_bpp),
+			      intel_dp_max_data_rate(pipe_config->port_clock,
+						     pipe_config->lane_count));
+	} else {
+		DRM_DEBUG_KMS("DP lane count %d clock %d bpp %d\n",
+			      pipe_config->lane_count, pipe_config->port_clock,
+			      pipe_config->pipe_bpp);
 
+		DRM_DEBUG_KMS("DP link rate required %i available %i\n",
+			      intel_dp_link_required(adjusted_mode->crtc_clock,
+						     pipe_config->pipe_bpp),
+			      intel_dp_max_data_rate(pipe_config->port_clock,
+						     pipe_config->lane_count));
+	}
 	return true;
 }
 
@@ -1983,7 +2122,7 @@ intel_dp_compute_config(struct intel_encoder *encoder,
 	if (adjusted_mode->flags & DRM_MODE_FLAG_DBLCLK)
 		return false;
 
-	if (!intel_dp_compute_link_config(encoder, pipe_config))
+	if (!intel_dp_compute_link_config(encoder, pipe_config, conn_state))
 		return false;
 
 	if (intel_conn_state->broadcast_rgb == INTEL_BROADCAST_RGB_AUTO) {
@@ -2001,11 +2140,20 @@ intel_dp_compute_config(struct intel_encoder *encoder,
 			intel_conn_state->broadcast_rgb == INTEL_BROADCAST_RGB_LIMITED;
 	}
 
-	intel_link_compute_m_n(pipe_config->pipe_bpp, pipe_config->lane_count,
-			       adjusted_mode->crtc_clock,
-			       pipe_config->port_clock,
-			       &pipe_config->dp_m_n,
-			       constant_n);
+	if (!pipe_config->dsc_params.compression_enable)
+		intel_link_compute_m_n(pipe_config->pipe_bpp,
+				       pipe_config->lane_count,
+				       adjusted_mode->crtc_clock,
+				       pipe_config->port_clock,
+				       &pipe_config->dp_m_n,
+				       constant_n);
+	else
+		intel_link_compute_m_n(pipe_config->dsc_params.compression_enable,
+				       pipe_config->lane_count,
+				       adjusted_mode->crtc_clock,
+				       pipe_config->port_clock,
+				       &pipe_config->dp_m_n,
+				       constant_n);
 
 	if (intel_connector->panel.downclock_mode != NULL &&
 		dev_priv->drrs.type == SEAMLESS_DRRS_SUPPORT) {
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 03/17] drm/i915/dp: Do not enable PSR2 if DSC is enabled

[Manasi Navare]

If a eDP panel supports both PSR2 and VDSC, our HW cannot
support both at a time. Give priority to PSR2 if a requested
resolution can be supported without compression else enable
VDSC and keep PSR2 disabled.

v4:
Fix the unrealted stuff removed during rebase (Ville)
v3:
* Rebase
v2:
* Add warning for DSC and PSR2 enabled together (DK)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
---
 drivers/gpu/drm/i915/intel_psr.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_psr.c b/drivers/gpu/drm/i915/intel_psr.c
index 572e626eadff..2084784f320d 100644
--- a/drivers/gpu/drm/i915/intel_psr.c
+++ b/drivers/gpu/drm/i915/intel_psr.c
@@ -75,6 +75,10 @@ static bool intel_psr2_enabled(struct drm_i915_private *dev_priv,
 	if (i915_modparams.enable_psr == -1)
 		return false;
 
+	/* Cannot enable DSC and PSR2 simultaneously */
+	WARN_ON(crtc_state->dsc_params.compression_enable &&
+		crtc_state->has_psr2);
+
 	switch (dev_priv->psr.debug & I915_PSR_DEBUG_MODE_MASK) {
 	case I915_PSR_DEBUG_FORCE_PSR1:
 		return false;
@@ -502,6 +506,16 @@ static bool intel_psr2_config_valid(struct intel_dp *intel_dp,
 	if (!dev_priv->psr.sink_psr2_support)
 		return false;
 
+	/*
+	 * DSC and PSR2 cannot be enabled simultaneously. If a requested
+	 * resolution requires DSC to be enabled, priority is given to DSC
+	 * over PSR2.
+	 */
+	if (crtc_state->dsc_params.compression_enable) {
+		DRM_DEBUG_KMS("PSR2 cannot be enabled since DSC is enabled\n");
+		return false;
+	}
+
 	if (INTEL_GEN(dev_priv) >= 10 || IS_GEMINILAKE(dev_priv)) {
 		psr_max_h = 4096;
 		psr_max_v = 2304;
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 04/17] drm/i915/dsc: Define & Compute VESA DSC params

[Manasi Navare]

From: Gaurav K Singh <gaurav.k.singh@intel.com>

This patches does the following:

1. This patch defines all the DSC parameters as per the VESA
DSC specification. These are stored in the encoder and used
to compute the PPS parameters to be sent to the Sink.
2. Compute all the DSC parameters which are derived from DSC
state of intel_crtc_state.
3. Compute all parameters that are VESA DSC specific

This computation happens in the atomic check phase during
compute_config() to validate if display stream compression
can be enabled for the requested mode.

v8 (From Manasi):
* DEBUG_KMS instead of DRM_ERROR for user triggerable
errors (Ville)
v7: (From Manasi)
* Dont use signed int for rc_range_params (Manasi)
* Mask the range_bpg_offset to use only 6 bits
* Add SPDX identifier (Chris Wilson)
v6 (From Manasi):
* Add a check for line_buf_depth return value (Anusha)
* Remove DRM DSC constants to different patch (Manasi)
v5 (From Manasi):
* Add logic to limit the max line buf depth for DSC 1.1 to 13
as per DSC 1.1 spec
* Fix dim checkpatch warnings/checks

v4 (From Gaurav):
* Rebase on latest drm tip
* rename variable name(Manasi)
* Populate linebuf_depth variable(Manasi)

v3 (From Gaurav):
* Rebase my previous patches on top of Manasi's latest patch
series
* Using >>n rather than /2^n (Manasi)
* Change the commit message to explain what the patch is doing(Gaurav)

Fixed review comments from Ville:
* Don't use macro TWOS_COMPLEMENT
* Mention in comment about the source of RC params
* Return directly from case statements
* Using single asssignment for assigning rc_range_params
* Using <<n rather than *2^n and removing the comments
about the fixed point numbers

v2 (From Manasi):
* Update logic for minor version to consider the dpcd value
and what supported by the HW platform
* Use DRM DSC config struct instead of intel_dp struct
* Move the DSC constants to DRM DSC header file
* Use u16, u8 where bigger data types not needed
* * Compute the DSC parameters as part of DSC compute config
since the computation can fail (Manasi)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Co-developed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
---
 drivers/gpu/drm/i915/Makefile     |   3 +-
 drivers/gpu/drm/i915/intel_dp.c   |   7 +
 drivers/gpu/drm/i915/intel_drv.h  |   4 +
 drivers/gpu/drm/i915/intel_vdsc.c | 456 ++++++++++++++++++++++++++++++
 include/drm/drm_dp_helper.h       |   3 +
 5 files changed, 472 insertions(+), 1 deletion(-)
 create mode 100644 drivers/gpu/drm/i915/intel_vdsc.c

diff --git a/drivers/gpu/drm/i915/Makefile b/drivers/gpu/drm/i915/Makefile
index 0ff878c994e2..8370b9de6e4f 100644
--- a/drivers/gpu/drm/i915/Makefile
+++ b/drivers/gpu/drm/i915/Makefile
@@ -157,7 +157,8 @@ i915-y += dvo_ch7017.o \
 	  intel_sdvo.o \
 	  intel_tv.o \
 	  vlv_dsi.o \
-	  vlv_dsi_pll.o
+	  vlv_dsi_pll.o \
+	  intel_vdsc.o
 
 # Post-mortem debug and GPU hang state capture
 i915-$(CONFIG_DRM_I915_CAPTURE_ERROR) += i915_gpu_error.o
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index a2780733768a..3b612eb134e7 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -1953,6 +1953,13 @@ static bool intel_dp_dsc_compute_config(struct intel_dp *intel_dp,
 			return false;
 		}
 	}
+	if (intel_dp_compute_dsc_params(intel_dp, pipe_config) < 0) {
+		DRM_DEBUG_KMS("Cannot compute valid DSC parameters for Input Bpp = %d "
+			      "Compressed BPP = %d\n",
+			      pipe_config->pipe_bpp,
+			      pipe_config->dsc_params.compressed_bpp);
+		return false;
+	}
 	pipe_config->dsc_params.compression_enable = true;
 	DRM_DEBUG_KMS("DP DSC computed with Input Bpp = %d "
 		      "Compressed Bpp = %d Slice Count = %d\n",
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index 270212fa43a0..316ec1e107bf 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -1852,6 +1852,10 @@ uint16_t intel_dp_dsc_get_output_bpp(int link_clock, uint8_t lane_count,
 uint8_t intel_dp_dsc_get_slice_count(struct intel_dp *intel_dp, int mode_clock,
 				     int mode_hdisplay);
 
+/* intel_vdsc.c */
+int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
+				struct intel_crtc_state *pipe_config);
+
 static inline unsigned int intel_dp_unused_lane_mask(int lane_count)
 {
 	return ~((1 << lane_count) - 1) & 0xf;
diff --git a/drivers/gpu/drm/i915/intel_vdsc.c b/drivers/gpu/drm/i915/intel_vdsc.c
new file mode 100644
index 000000000000..4ce6f0c453bb
--- /dev/null
+++ b/drivers/gpu/drm/i915/intel_vdsc.c
@@ -0,0 +1,456 @@
+// SPDX-License-Identifier: MIT
+/*
+ * Copyright © 2018 Intel Corporation
+ *
+ * Author: Gaurav K Singh <gaurav.k.singh@intel.com>
+ *         Manasi Navare <manasi.d.navare@intel.com>
+ */
+
+#include <drm/drmP.h>
+#include <drm/i915_drm.h>
+#include "i915_drv.h"
+#include "intel_drv.h"
+
+enum ROW_INDEX_BPP {
+	ROW_INDEX_6BPP = 0,
+	ROW_INDEX_8BPP,
+	ROW_INDEX_10BPP,
+	ROW_INDEX_12BPP,
+	ROW_INDEX_15BPP,
+	MAX_ROW_INDEX
+};
+
+enum COLUMN_INDEX_BPC {
+	COLUMN_INDEX_8BPC = 0,
+	COLUMN_INDEX_10BPC,
+	COLUMN_INDEX_12BPC,
+	COLUMN_INDEX_14BPC,
+	COLUMN_INDEX_16BPC,
+	MAX_COLUMN_INDEX
+};
+
+#define DSC_SUPPORTED_VERSION_MIN		1
+
+/* From DSC_v1.11 spec, rc_parameter_Set syntax element typically constant */
+static u16 rc_buf_thresh[] = {
+	896, 1792, 2688, 3584, 4480, 5376, 6272, 6720, 7168, 7616,
+	7744, 7872, 8000, 8064
+};
+
+struct rc_parameters {
+	u16 initial_xmit_delay;
+	u8 first_line_bpg_offset;
+	u16 initial_offset;
+	u8 flatness_min_qp;
+	u8 flatness_max_qp;
+	u8 rc_quant_incr_limit0;
+	u8 rc_quant_incr_limit1;
+	struct drm_dsc_rc_range_parameters rc_range_params[DSC_NUM_BUF_RANGES];
+};
+
+/*
+ * Selected Rate Control Related Parameter Recommended Values
+ * from DSC_v1.11 spec & C Model release: DSC_model_20161212
+ */
+static struct rc_parameters rc_params[][MAX_COLUMN_INDEX] = {
+{
+	/* 6BPP/8BPC */
+	{ 768, 15, 6144, 3, 13, 11, 11, {
+		{ 0, 4, 0 }, { 1, 6, -2 }, { 3, 8, -2 }, { 4, 8, -4 },
+		{ 5, 9, -6 }, { 5, 9, -6 }, { 6, 9, -6 }, { 6, 10, -8 },
+		{ 7, 11, -8 }, { 8, 12, -10 }, { 9, 12, -10 }, { 10, 12, -12 },
+		{ 10, 12, -12 }, { 11, 12, -12 }, { 13, 14, -12 }
+		}
+	},
+	/* 6BPP/10BPC */
+	{ 768, 15, 6144, 7, 17, 15, 15, {
+		{ 0, 8, 0 }, { 3, 10, -2 }, { 7, 12, -2 }, { 8, 12, -4 },
+		{ 9, 13, -6 }, { 9, 13, -6 }, { 10, 13, -6 }, { 10, 14, -8 },
+		{ 11, 15, -8 }, { 12, 16, -10 }, { 13, 16, -10 },
+		{ 14, 16, -12 }, { 14, 16, -12 }, { 15, 16, -12 },
+		{ 17, 18, -12 }
+		}
+	},
+	/* 6BPP/12BPC */
+	{ 768, 15, 6144, 11, 21, 19, 19, {
+		{ 0, 12, 0 }, { 5, 14, -2 }, { 11, 16, -2 }, { 12, 16, -4 },
+		{ 13, 17, -6 }, { 13, 17, -6 }, { 14, 17, -6 }, { 14, 18, -8 },
+		{ 15, 19, -8 }, { 16, 20, -10 }, { 17, 20, -10 },
+		{ 18, 20, -12 }, { 18, 20, -12 }, { 19, 20, -12 },
+		{ 21, 22, -12 }
+		}
+	},
+	/* 6BPP/14BPC */
+	{ 768, 15, 6144, 15, 25, 23, 27, {
+		{ 0, 16, 0 }, { 7, 18, -2 }, { 15, 20, -2 }, { 16, 20, -4 },
+		{ 17, 21, -6 }, { 17, 21, -6 }, { 18, 21, -6 }, { 18, 22, -8 },
+		{ 19, 23, -8 }, { 20, 24, -10 }, { 21, 24, -10 },
+		{ 22, 24, -12 }, { 22, 24, -12 }, { 23, 24, -12 },
+		{ 25, 26, -12 }
+		}
+	},
+	/* 6BPP/16BPC */
+	{ 768, 15, 6144, 19, 29, 27, 27, {
+		{ 0, 20, 0 }, { 9, 22, -2 }, { 19, 24, -2 }, { 20, 24, -4 },
+		{ 21, 25, -6 }, { 21, 25, -6 }, { 22, 25, -6 }, { 22, 26, -8 },
+		{ 23, 27, -8 }, { 24, 28, -10 }, { 25, 28, -10 },
+		{ 26, 28, -12 }, { 26, 28, -12 }, { 27, 28, -12 },
+		{ 29, 30, -12 }
+		}
+	},
+},
+{
+	/* 8BPP/8BPC */
+	{ 512, 12, 6144, 3, 12, 11, 11, {
+		{ 0, 4, 2 }, { 0, 4, 0 }, { 1, 5, 0 }, { 1, 6, -2 },
+		{ 3, 7, -4 }, { 3, 7, -6 }, { 3, 7, -8 }, { 3, 8, -8 },
+		{ 3, 9, -8 }, { 3, 10, -10 }, { 5, 11, -10 }, { 5, 12, -12 },
+		{ 5, 13, -12 }, { 7, 13, -12 }, { 13, 15, -12 }
+		}
+	},
+	/* 8BPP/10BPC */
+	{ 512, 12, 6144, 7, 16, 15, 15, {
+		{ 0, 4, 2 }, { 4, 8, 0 }, { 5, 9, 0 }, { 5, 10, -2 },
+		{ 7, 11, -4 }, { 7, 11, -6 }, { 7, 11, -8 }, { 7, 12, -8 },
+		{ 7, 13, -8 }, { 7, 14, -10 }, { 9, 15, -10 }, { 9, 16, -12 },
+		{ 9, 17, -12 }, { 11, 17, -12 }, { 17, 19, -12 }
+		}
+	},
+	/* 8BPP/12BPC */
+	{ 512, 12, 6144, 11, 20, 19, 19, {
+		{ 0, 12, 2 }, { 4, 12, 0 }, { 9, 13, 0 }, { 9, 14, -2 },
+		{ 11, 15, -4 }, { 11, 15, -6 }, { 11, 15, -8 }, { 11, 16, -8 },
+		{ 11, 17, -8 }, { 11, 18, -10 }, { 13, 19, -10 },
+		{ 13, 20, -12 }, { 13, 21, -12 }, { 15, 21, -12 },
+		{ 21, 23, -12 }
+		}
+	},
+	/* 8BPP/14BPC */
+	{ 512, 12, 6144, 15, 24, 23, 23, {
+		{ 0, 12, 0 }, { 5, 13, 0 }, { 11, 15, 0 }, { 12, 17, -2 },
+		{ 15, 19, -4 }, { 15, 19, -6 }, { 15, 19, -8 }, { 15, 20, -8 },
+		{ 15, 21, -8 }, { 15, 22, -10 }, { 17, 22, -10 },
+		{ 17, 23, -12 }, { 17, 23, -12 }, { 21, 24, -12 },
+		{ 24, 25, -12 }
+		}
+	},
+	/* 8BPP/16BPC */
+	{ 512, 12, 6144, 19, 28, 27, 27, {
+		{ 0, 12, 2 }, { 6, 14, 0 }, { 13, 17, 0 }, { 15, 20, -2 },
+		{ 19, 23, -4 }, { 19, 23, -6 }, { 19, 23, -8 }, { 19, 24, -8 },
+		{ 19, 25, -8 }, { 19, 26, -10 }, { 21, 26, -10 },
+		{ 21, 27, -12 }, { 21, 27, -12 }, { 25, 28, -12 },
+		{ 28, 29, -12 }
+		}
+	},
+},
+{
+	/* 10BPP/8BPC */
+	{ 410, 15, 5632, 3, 12, 11, 11, {
+		{ 0, 3, 2 }, { 0, 4, 0 }, { 1, 5, 0 }, { 2, 6, -2 },
+		{ 3, 7, -4 }, { 3, 7, -6 }, { 3, 7, -8 }, { 3, 8, -8 },
+		{ 3, 9, -8 }, { 3, 9, -10 }, { 5, 10, -10 }, { 5, 10, -10 },
+		{ 5, 11, -12 }, { 7, 11, -12 }, { 11, 12, -12 }
+		}
+	},
+	/* 10BPP/10BPC */
+	{ 410, 15, 5632, 7, 16, 15, 15, {
+		{ 0, 7, 2 }, { 4, 8, 0 }, { 5, 9, 0 }, { 6, 10, -2 },
+		{ 7, 11, -4 }, { 7, 11, -6 }, { 7, 11, -8 }, { 7, 12, -8 },
+		{ 7, 13, -8 }, { 7, 13, -10 }, { 9, 14, -10 }, { 9, 14, -10 },
+		{ 9, 15, -12 }, { 11, 15, -12 }, { 15, 16, -12 }
+		}
+	},
+	/* 10BPP/12BPC */
+	{ 410, 15, 5632, 11, 20, 19, 19, {
+		{ 0, 11, 2 }, { 4, 12, 0 }, { 9, 13, 0 }, { 10, 14, -2 },
+		{ 11, 15, -4 }, { 11, 15, -6 }, { 11, 15, -8 }, { 11, 16, -8 },
+		{ 11, 17, -8 }, { 11, 17, -10 }, { 13, 18, -10 },
+		{ 13, 18, -10 }, { 13, 19, -12 }, { 15, 19, -12 },
+		{ 19, 20, -12 }
+		}
+	},
+	/* 10BPP/14BPC */
+	{ 410, 15, 5632, 15, 24, 23, 23, {
+		{ 0, 11, 2 }, { 5, 13, 0 }, { 11, 15, 0 }, { 13, 18, -2 },
+		{ 15, 19, -4 }, { 15, 19, -6 }, { 15, 19, -8 }, { 15, 20, -8 },
+		{ 15, 21, -8 }, { 15, 21, -10 }, { 17, 22, -10 },
+		{ 17, 22, -10 }, { 17, 23, -12 }, { 19, 23, -12 },
+		{ 23, 24, -12 }
+		}
+	},
+	/* 10BPP/16BPC */
+	{ 410, 15, 5632, 19, 28, 27, 27, {
+		{ 0, 11, 2 }, { 6, 14, 0 }, { 13, 17, 0 }, { 16, 20, -2 },
+		{ 19, 23, -4 }, { 19, 23, -6 }, { 19, 23, -8 }, { 19, 24, -8 },
+		{ 19, 25, -8 }, { 19, 25, -10 }, { 21, 26, -10 },
+		{ 21, 26, -10 }, { 21, 27, -12 }, { 23, 27, -12 },
+		{ 27, 28, -12 }
+		}
+	},
+},
+{
+	/* 12BPP/8BPC */
+	{ 341, 15, 2048, 3, 12, 11, 11, {
+		{ 0, 2, 2 }, { 0, 4, 0 }, { 1, 5, 0 }, { 1, 6, -2 },
+		{ 3, 7, -4 }, { 3, 7, -6 }, { 3, 7, -8 }, { 3, 8, -8 },
+		{ 3, 9, -8 }, { 3, 10, -10 }, { 5, 11, -10 },
+		{ 5, 12, -12 }, { 5, 13, -12 }, { 7, 13, -12 }, { 13, 15, -12 }
+		}
+	},
+	/* 12BPP/10BPC */
+	{ 341, 15, 2048, 7, 16, 15, 15, {
+		{ 0, 2, 2 }, { 2, 5, 0 }, { 3, 7, 0 }, { 4, 8, -2 },
+		{ 6, 9, -4 }, { 7, 10, -6 }, { 7, 11, -8 }, { 7, 12, -8 },
+		{ 7, 13, -8 }, { 7, 14, -10 }, { 9, 15, -10 }, { 9, 16, -12 },
+		{ 9, 17, -12 }, { 11, 17, -12 }, { 17, 19, -12 }
+		}
+	},
+	/* 12BPP/12BPC */
+	{ 341, 15, 2048, 11, 20, 19, 19, {
+		{ 0, 6, 2 }, { 4, 9, 0 }, { 7, 11, 0 }, { 8, 12, -2 },
+		{ 10, 13, -4 }, { 11, 14, -6 }, { 11, 15, -8 }, { 11, 16, -8 },
+		{ 11, 17, -8 }, { 11, 18, -10 }, { 13, 19, -10 },
+		{ 13, 20, -12 }, { 13, 21, -12 }, { 15, 21, -12 },
+		{ 21, 23, -12 }
+		}
+	},
+	/* 12BPP/14BPC */
+	{ 341, 15, 2048, 15, 24, 23, 23, {
+		{ 0, 6, 2 }, { 7, 10, 0 }, { 9, 13, 0 }, { 11, 16, -2 },
+		{ 14, 17, -4 }, { 15, 18, -6 }, { 15, 19, -8 }, { 15, 20, -8 },
+		{ 15, 20, -8 }, { 15, 21, -10 }, { 17, 21, -10 },
+		{ 17, 21, -12 }, { 17, 21, -12 }, { 19, 22, -12 },
+		{ 22, 23, -12 }
+		}
+	},
+	/* 12BPP/16BPC */
+	{ 341, 15, 2048, 19, 28, 27, 27, {
+		{ 0, 6, 2 }, { 6, 11, 0 }, { 11, 15, 0 }, { 14, 18, -2 },
+		{ 18, 21, -4 }, { 19, 22, -6 }, { 19, 23, -8 }, { 19, 24, -8 },
+		{ 19, 24, -8 }, { 19, 25, -10 }, { 21, 25, -10 },
+		{ 21, 25, -12 }, { 21, 25, -12 }, { 23, 26, -12 },
+		{ 26, 27, -12 }
+		}
+	},
+},
+{
+	/* 15BPP/8BPC */
+	{ 273, 15, 2048, 3, 12, 11, 11, {
+		{ 0, 0, 10 }, { 0, 1, 8 }, { 0, 1, 6 }, { 0, 2, 4 },
+		{ 1, 2, 2 }, { 1, 3, 0 }, { 1, 3, -2 }, { 2, 4, -4 },
+		{ 2, 5, -6 }, { 3, 5, -8 }, { 4, 6, -10 }, { 4, 7, -10 },
+		{ 5, 7, -12 }, { 7, 8, -12 }, { 8, 9, -12 }
+		}
+	},
+	/* 15BPP/10BPC */
+	{ 273, 15, 2048, 7, 16, 15, 15, {
+		{ 0, 2, 10 }, { 2, 5, 8 }, { 3, 5, 6 }, { 4, 6, 4 },
+		{ 5, 6, 2 }, { 5, 7, 0 }, { 5, 7, -2 }, { 6, 8, -4 },
+		{ 6, 9, -6 }, { 7, 9, -8 }, { 8, 10, -10 }, { 8, 11, -10 },
+		{ 9, 11, -12 }, { 11, 12, -12 }, { 12, 13, -12 }
+		}
+	},
+	/* 15BPP/12BPC */
+	{ 273, 15, 2048, 11, 20, 19, 19, {
+		{ 0, 4, 10 }, { 2, 7, 8 }, { 4, 9, 6 }, { 6, 11, 4 },
+		{ 9, 11, 2 }, { 9, 11, 0 }, { 9, 12, -2 }, { 10, 12, -4 },
+		{ 11, 13, -6 }, { 11, 13, -8 }, { 12, 14, -10 },
+		{ 13, 15, -10 }, { 13, 15, -12 }, { 15, 16, -12 },
+		{ 16, 17, -12 }
+		}
+	},
+	/* 15BPP/14BPC */
+	{ 273, 15, 2048, 15, 24, 23, 23, {
+		{ 0, 4, 10 }, { 3, 8, 8 }, { 6, 11, 6 }, { 9, 14, 4 },
+		{ 13, 15, 2 }, { 13, 15, 0 }, { 13, 16, -2 }, { 14, 16, -4 },
+		{ 15, 17, -6 }, { 15, 17, -8 }, { 16, 18, -10 },
+		{ 17, 19, -10 }, { 17, 19, -12 }, { 19, 20, -12 },
+		{ 20, 21, -12 }
+		}
+	},
+	/* 15BPP/16BPC */
+	{ 273, 15, 2048, 19, 28, 27, 27, {
+		{ 0, 4, 10 }, { 4, 9, 8 }, { 8, 13, 6 }, { 12, 17, 4 },
+		{ 17, 19, 2 }, { 17, 20, 0 }, { 17, 20, -2 }, { 18, 20, -4 },
+		{ 19, 21, -6 }, { 19, 21, -8 }, { 20, 22, -10 },
+		{ 21, 23, -10 }, { 21, 23, -12 }, { 23, 24, -12 },
+		{ 24, 25, -12 }
+		}
+	}
+}
+
+};
+
+static int get_row_index_for_rc_params(u16 compressed_bpp)
+{
+	switch (compressed_bpp) {
+	case 6:
+		return ROW_INDEX_6BPP;
+	case 8:
+		return ROW_INDEX_8BPP;
+	case 10:
+		return ROW_INDEX_10BPP;
+	case 12:
+		return ROW_INDEX_12BPP;
+	case 15:
+		return ROW_INDEX_15BPP;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int get_column_index_for_rc_params(u8 bits_per_component)
+{
+	switch (bits_per_component) {
+	case 8:
+		return COLUMN_INDEX_8BPC;
+	case 10:
+		return COLUMN_INDEX_10BPC;
+	case 12:
+		return COLUMN_INDEX_12BPC;
+	case 14:
+		return COLUMN_INDEX_14BPC;
+	case 16:
+		return COLUMN_INDEX_16BPC;
+	default:
+		return -EINVAL;
+	}
+}
+
+int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
+				struct intel_crtc_state *pipe_config)
+{
+	struct drm_dsc_config *vdsc_cfg = &pipe_config->dp_dsc_cfg;
+	u16 compressed_bpp = pipe_config->dsc_params.compressed_bpp;
+	u8 i = 0;
+	u8 row_index = 0;
+	u8 column_index = 0;
+	u8 line_buf_depth = 0;
+
+	vdsc_cfg->pic_width = pipe_config->base.adjusted_mode.crtc_hdisplay;
+	vdsc_cfg->pic_height = pipe_config->base.adjusted_mode.crtc_vdisplay;
+	vdsc_cfg->slice_width = DIV_ROUND_UP(vdsc_cfg->pic_width,
+					     pipe_config->dsc_params.slice_count);
+	/*
+	 * Slice Height of 8 works for all currently available panels. So start
+	 * with that if pic_height is an integral multiple of 8.
+	 * Eventually add logic to try multiple slice heights.
+	 */
+	if (vdsc_cfg->pic_height % 8 == 0)
+		vdsc_cfg->slice_height = 8;
+	else if (vdsc_cfg->pic_height % 4 == 0)
+		vdsc_cfg->slice_height = 4;
+	else
+		vdsc_cfg->slice_height = 2;
+
+	/* Values filled from DSC Sink DPCD */
+	vdsc_cfg->dsc_version_major =
+		(intel_dp->dsc_dpcd[DP_DSC_REV - DP_DSC_SUPPORT] &
+		 DP_DSC_MAJOR_MASK) >> DP_DSC_MAJOR_SHIFT;
+	vdsc_cfg->dsc_version_minor =
+		min(DSC_SUPPORTED_VERSION_MIN,
+		    (intel_dp->dsc_dpcd[DP_DSC_REV - DP_DSC_SUPPORT] &
+		     DP_DSC_MINOR_MASK) >> DP_DSC_MINOR_SHIFT);
+
+	vdsc_cfg->convert_rgb = intel_dp->dsc_dpcd[DP_DSC_DEC_COLOR_FORMAT_CAP - DP_DSC_SUPPORT] &
+		DP_DSC_RGB;
+
+	line_buf_depth = drm_dp_dsc_sink_line_buf_depth(intel_dp->dsc_dpcd);
+	if (!line_buf_depth) {
+		DRM_DEBUG_KMS("DSC Sink Line Buffer Depth invalid\n");
+		return -EINVAL;
+	}
+	if (vdsc_cfg->dsc_version_minor == 2)
+		vdsc_cfg->line_buf_depth = (line_buf_depth == DSC_1_2_MAX_LINEBUF_DEPTH_BITS) ?
+			DSC_1_2_MAX_LINEBUF_DEPTH_VAL : line_buf_depth;
+	else
+		vdsc_cfg->line_buf_depth = (line_buf_depth > DSC_1_1_MAX_LINEBUF_DEPTH_BITS) ?
+			DSC_1_1_MAX_LINEBUF_DEPTH_BITS : line_buf_depth;
+
+	/* Gen 11 does not support YCbCr */
+	vdsc_cfg->enable422 = false;
+	/* Gen 11 does not support VBR */
+	vdsc_cfg->vbr_enable = false;
+	vdsc_cfg->block_pred_enable =
+			intel_dp->dsc_dpcd[DP_DSC_BLK_PREDICTION_SUPPORT - DP_DSC_SUPPORT] &
+		DP_DSC_BLK_PREDICTION_IS_SUPPORTED;
+
+	/* Gen 11 only supports integral values of bpp */
+	vdsc_cfg->bits_per_pixel = compressed_bpp << 4;
+	vdsc_cfg->bits_per_component = pipe_config->pipe_bpp / 3;
+
+	for (i = 0; i < DSC_NUM_BUF_RANGES - 1; i++) {
+		/*
+		 * six 0s are appended to the lsb of each threshold value
+		 * internally in h/w.
+		 * Only 8 bits are allowed for programming RcBufThreshold
+		 */
+		vdsc_cfg->rc_buf_thresh[i] = rc_buf_thresh[i] >> 6;
+	}
+
+	/*
+	 * For 6bpp, RC Buffer threshold 12 and 13 need a different value
+	 * as per C Model
+	 */
+	if (compressed_bpp == 6) {
+		vdsc_cfg->rc_buf_thresh[12] = 0x7C;
+		vdsc_cfg->rc_buf_thresh[13] = 0x7D;
+	}
+
+	row_index = get_row_index_for_rc_params(compressed_bpp);
+	column_index =
+		get_column_index_for_rc_params(vdsc_cfg->bits_per_component);
+
+	if (row_index < 0 || column_index < 0)
+		return -EINVAL;
+
+	vdsc_cfg->first_line_bpg_offset =
+		rc_params[row_index][column_index].first_line_bpg_offset;
+	vdsc_cfg->initial_xmit_delay =
+		rc_params[row_index][column_index].initial_xmit_delay;
+	vdsc_cfg->initial_offset =
+		rc_params[row_index][column_index].initial_offset;
+	vdsc_cfg->flatness_min_qp =
+		rc_params[row_index][column_index].flatness_min_qp;
+	vdsc_cfg->flatness_max_qp =
+		rc_params[row_index][column_index].flatness_max_qp;
+	vdsc_cfg->rc_quant_incr_limit0 =
+		rc_params[row_index][column_index].rc_quant_incr_limit0;
+	vdsc_cfg->rc_quant_incr_limit1 =
+		rc_params[row_index][column_index].rc_quant_incr_limit1;
+
+	for (i = 0; i < DSC_NUM_BUF_RANGES; i++) {
+		vdsc_cfg->rc_range_params[i].range_min_qp =
+			rc_params[row_index][column_index].rc_range_params[i].range_min_qp;
+		vdsc_cfg->rc_range_params[i].range_max_qp =
+			rc_params[row_index][column_index].rc_range_params[i].range_max_qp;
+		/*
+		 * Range BPG Offset uses 2's complement and is only a 6 bits. So
+		 * mask it to get only 6 bits.
+		 */
+		vdsc_cfg->rc_range_params[i].range_bpg_offset =
+			rc_params[row_index][column_index].rc_range_params[i].range_bpg_offset &
+			DSC_RANGE_BPG_OFFSET_MASK;
+	}
+
+	/*
+	 * BitsPerComponent value determines mux_word_size:
+	 * When BitsPerComponent is 12bpc, muxWordSize will be equal to 64 bits
+	 * When BitsPerComponent is 8 or 10bpc, muxWordSize will be equal to
+	 * 48 bits
+	 */
+	if (vdsc_cfg->bits_per_component == 8 ||
+	    vdsc_cfg->bits_per_component == 10)
+		vdsc_cfg->mux_word_size = DSC_MUX_WORD_SIZE_8_10_BPC;
+	else if (vdsc_cfg->bits_per_component == 12)
+		vdsc_cfg->mux_word_size = DSC_MUX_WORD_SIZE_12_BPC;
+
+	/* RC_MODEL_SIZE is a constant across all configurations */
+	vdsc_cfg->rc_model_size = DSC_RC_MODEL_SIZE_CONST;
+	/* InitialScaleValue is a 6 bit value with 3 fractional bits (U3.3) */
+	vdsc_cfg->initial_scale_value = (vdsc_cfg->rc_model_size << 3) /
+		(vdsc_cfg->rc_model_size - vdsc_cfg->initial_offset);
+
+	return 0;
+}
diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
index 5736c942c85b..61c6ecc0a02b 100644
--- a/include/drm/drm_dp_helper.h
+++ b/include/drm/drm_dp_helper.h
@@ -187,6 +187,9 @@
 
 #define DP_GUID				    0x030   /* 1.2 */
 
+#define DP_DSC_RC_PIXELS_PER_GROUP		3
+#define DP_DSC_SCALE_DECREMENT_INTERVAL_MAX	4095
+
 #define DP_DSC_SUPPORT                      0x060   /* DP 1.4 */
 # define DP_DSC_DECOMPRESSION_IS_SUPPORTED  (1 << 0)
 
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 05/17] drm/i915/dsc: Compute Rate Control parameters for DSC

[Manasi Navare]

From: Gaurav K Singh <gaurav.k.singh@intel.com>

This computation of RC params happens in the atomic commit phase
during compute_config() to validate if display stream compression
can be enabled for the requested mode.

v7 (From Manasi):
* Use DRM_DEBUG instead of DRM_ERROR (Ville)
* Use Error numberinstead of -1 (Ville)
v6 (From Manasi):
* Use 9 instead of 0x9 for consistency (Anusha)

v5 (From Manasi):
* Fix dim checkpatch warnings/checks
v4(From Gaurav):
* No change.Rebase on drm-tip

v3 (From Gaurav):
* Rebase on top of Manasi's latest series
* Return -ve value in case of failure scenarios (Manasi)

Fix review comments from Ville:
* Remove unnecessary comments
* Remove unnecessary paranthesis
* Add comments for few RC params calculations

v2 (From Manasi):
* Rebase Gaurav's patch from intel-gfx to gfx-internal
* Use struct drm_dsc_cfg instead of struct intel_dp
as a parameter

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
---
 drivers/gpu/drm/i915/intel_vdsc.c | 125 +++++++++++++++++++++++++++++-
 1 file changed, 124 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/i915/intel_vdsc.c b/drivers/gpu/drm/i915/intel_vdsc.c
index 4ce6f0c453bb..39baff618ed8 100644
--- a/drivers/gpu/drm/i915/intel_vdsc.c
+++ b/drivers/gpu/drm/i915/intel_vdsc.c
@@ -318,6 +318,129 @@ static int get_column_index_for_rc_params(u8 bits_per_component)
 	}
 }
 
+static int intel_compute_rc_parameters(struct drm_dsc_config *vdsc_cfg)
+{
+	unsigned long groups_per_line = 0;
+	unsigned long groups_total = 0;
+	unsigned long num_extra_mux_bits = 0;
+	unsigned long slice_bits = 0;
+	unsigned long hrd_delay = 0;
+	unsigned long final_scale = 0;
+	unsigned long rbs_min = 0;
+
+	/* Number of groups used to code each line of a slice */
+	groups_per_line = DIV_ROUND_UP(vdsc_cfg->slice_width,
+				       DSC_RC_PIXELS_PER_GROUP);
+
+	/* chunksize in Bytes */
+	vdsc_cfg->slice_chunk_size = DIV_ROUND_UP(vdsc_cfg->slice_width *
+						  vdsc_cfg->bits_per_pixel,
+						  (8 * 16));
+
+	if (vdsc_cfg->convert_rgb)
+		num_extra_mux_bits = 3 * (vdsc_cfg->mux_word_size +
+					  (4 * vdsc_cfg->bits_per_component + 4)
+					  - 2);
+	else
+		num_extra_mux_bits = 3 * vdsc_cfg->mux_word_size +
+			(4 * vdsc_cfg->bits_per_component + 4) +
+			2 * (4 * vdsc_cfg->bits_per_component) - 2;
+	/* Number of bits in one Slice */
+	slice_bits = 8 * vdsc_cfg->slice_chunk_size * vdsc_cfg->slice_height;
+
+	while ((num_extra_mux_bits > 0) &&
+	       ((slice_bits - num_extra_mux_bits) % vdsc_cfg->mux_word_size))
+		num_extra_mux_bits--;
+
+	if (groups_per_line < vdsc_cfg->initial_scale_value - 8)
+		vdsc_cfg->initial_scale_value = groups_per_line + 8;
+
+	/* scale_decrement_interval calculation according to DSC spec 1.11 */
+	if (vdsc_cfg->initial_scale_value > 8)
+		vdsc_cfg->scale_decrement_interval = groups_per_line /
+			(vdsc_cfg->initial_scale_value - 8);
+	else
+		vdsc_cfg->scale_decrement_interval = DSC_SCALE_DECREMENT_INTERVAL_MAX;
+
+	vdsc_cfg->final_offset = vdsc_cfg->rc_model_size -
+		(vdsc_cfg->initial_xmit_delay *
+		 vdsc_cfg->bits_per_pixel + 8) / 16 + num_extra_mux_bits;
+
+	if (vdsc_cfg->final_offset >= vdsc_cfg->rc_model_size) {
+		DRM_DEBUG_KMS("FinalOfs < RcModelSze for this InitialXmitDelay\n");
+		return -ERANGE;
+	}
+
+	final_scale = (vdsc_cfg->rc_model_size * 8) /
+		(vdsc_cfg->rc_model_size - vdsc_cfg->final_offset);
+	if (vdsc_cfg->slice_height > 1)
+		/*
+		 * NflBpgOffset is 16 bit value with 11 fractional bits
+		 * hence we multiply by 2^11 for preserving the
+		 * fractional part
+		 */
+		vdsc_cfg->nfl_bpg_offset = DIV_ROUND_UP((vdsc_cfg->first_line_bpg_offset << 11),
+							(vdsc_cfg->slice_height - 1));
+	else
+		vdsc_cfg->nfl_bpg_offset = 0;
+
+	/* 2^16 - 1 */
+	if (vdsc_cfg->nfl_bpg_offset > 65535) {
+		DRM_DEBUG_KMS("NflBpgOffset is too large for this slice height\n");
+		return -ERANGE;
+	}
+
+	/* Number of groups used to code the entire slice */
+	groups_total = groups_per_line * vdsc_cfg->slice_height;
+
+	/* slice_bpg_offset is 16 bit value with 11 fractional bits */
+	vdsc_cfg->slice_bpg_offset = DIV_ROUND_UP(((vdsc_cfg->rc_model_size -
+						    vdsc_cfg->initial_offset +
+						    num_extra_mux_bits) << 11),
+						  groups_total);
+
+	if (final_scale > 9) {
+		/*
+		 * ScaleIncrementInterval =
+		 * finaloffset/((NflBpgOffset + SliceBpgOffset)*8(finalscale - 1.125))
+		 * as (NflBpgOffset + SliceBpgOffset) has 11 bit fractional value,
+		 * we need divide by 2^11 from pstDscCfg values
+		 */
+		vdsc_cfg->scale_increment_interval =
+				(vdsc_cfg->final_offset * (1 << 11)) /
+				((vdsc_cfg->nfl_bpg_offset +
+				vdsc_cfg->slice_bpg_offset) *
+				(final_scale - 9));
+	} else {
+		/*
+		 * If finalScaleValue is less than or equal to 9, a value of 0 should
+		 * be used to disable the scale increment at the end of the slice
+		 */
+		vdsc_cfg->scale_increment_interval = 0;
+	}
+
+	if (vdsc_cfg->scale_increment_interval > 65535) {
+		DRM_DEBUG_KMS("ScaleIncrementInterval is large for slice height\n");
+		return -ERANGE;
+	}
+
+	/*
+	 * DSC spec mentions that bits_per_pixel specifies the target
+	 * bits/pixel (bpp) rate that is used by the encoder,
+	 * in steps of 1/16 of a bit per pixel
+	 */
+	rbs_min = vdsc_cfg->rc_model_size - vdsc_cfg->initial_offset +
+		DIV_ROUND_UP(vdsc_cfg->initial_xmit_delay *
+			     vdsc_cfg->bits_per_pixel, 16) +
+		groups_per_line * vdsc_cfg->first_line_bpg_offset;
+
+	hrd_delay = DIV_ROUND_UP((rbs_min * 16), vdsc_cfg->bits_per_pixel);
+	vdsc_cfg->rc_bits = (hrd_delay * vdsc_cfg->bits_per_pixel) / 16;
+	vdsc_cfg->initial_dec_delay = hrd_delay - vdsc_cfg->initial_xmit_delay;
+
+	return 0;
+}
+
 int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
 				struct intel_crtc_state *pipe_config)
 {
@@ -452,5 +575,5 @@ int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
 	vdsc_cfg->initial_scale_value = (vdsc_cfg->rc_model_size << 3) /
 		(vdsc_cfg->rc_model_size - vdsc_cfg->initial_offset);
 
-	return 0;
+	return intel_compute_rc_parameters(vdsc_cfg);
 }
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 06/17] drm/i915/dp: Enable/Disable DSC in DP Sink

[Manasi Navare]

From: Gaurav K Singh <gaurav.k.singh@intel.com>

This patch enables decompression support in sink device
before link training and disables the same during the
DDI disabling.

v3 (From manasi):
* Pass bool state to enable/disable (Ville)
v2:(From Manasi)
* Change the enable/disable function to take crtc_state
instead of intel_dp as an argument (Manasi)
* Use the compression_enable flag as part of crtc_state (Manasi)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
---
 drivers/gpu/drm/i915/intel_ddi.c |  5 +++++
 drivers/gpu/drm/i915/intel_dp.c  | 16 ++++++++++++++++
 drivers/gpu/drm/i915/intel_drv.h |  3 +++
 3 files changed, 24 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index ad11540ac436..fa5ad62cd0db 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -3134,6 +3134,8 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
 	intel_ddi_init_dp_buf_reg(encoder);
 	if (!is_mst)
 		intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
+	intel_dp_sink_set_decompression_state(intel_dp, crtc_state,
+					      true);
 	intel_dp_start_link_train(intel_dp);
 	if (port != PORT_A || INTEL_GEN(dev_priv) >= 9)
 		intel_dp_stop_link_train(intel_dp);
@@ -3491,6 +3493,9 @@ static void intel_disable_ddi_dp(struct intel_encoder *encoder,
 	intel_edp_drrs_disable(intel_dp, old_crtc_state);
 	intel_psr_disable(intel_dp, old_crtc_state);
 	intel_edp_backlight_off(old_conn_state);
+	/* Disable the decompression in DP Sink */
+	intel_dp_sink_set_decompression_state(intel_dp, old_crtc_state,
+					      false);
 }
 
 static void intel_disable_ddi_hdmi(struct intel_encoder *encoder,
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 3b612eb134e7..4e65dd1a6c07 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -2857,6 +2857,22 @@ static bool downstream_hpd_needs_d0(struct intel_dp *intel_dp)
 		intel_dp->downstream_ports[0] & DP_DS_PORT_HPD;
 }
 
+void intel_dp_sink_set_decompression_state(struct intel_dp *intel_dp,
+					   const struct intel_crtc_state *crtc_state,
+					   bool enable)
+{
+	int ret;
+
+	if (!crtc_state->dsc_params.compression_enable)
+		return;
+
+	ret = drm_dp_dpcd_writeb(&intel_dp->aux, DP_DSC_ENABLE,
+				 enable ? DP_DECOMPRESSION_EN : 0);
+	if (ret < 0)
+		DRM_DEBUG_KMS("Failed to %s sink decompression state\n",
+			      enable ? "enable" : "disable");
+}
+
 /* If the sink supports it, try to set the power state appropriately */
 void intel_dp_sink_dpms(struct intel_dp *intel_dp, int mode)
 {
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index 316ec1e107bf..fa452fbb16c6 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -1797,6 +1797,9 @@ void intel_dp_stop_link_train(struct intel_dp *intel_dp);
 int intel_dp_retrain_link(struct intel_encoder *encoder,
 			  struct drm_modeset_acquire_ctx *ctx);
 void intel_dp_sink_dpms(struct intel_dp *intel_dp, int mode);
+void intel_dp_sink_set_decompression_state(struct intel_dp *intel_dp,
+					   const struct intel_crtc_state *crtc_state,
+					   bool enable);
 void intel_dp_encoder_reset(struct drm_encoder *encoder);
 void intel_dp_encoder_suspend(struct intel_encoder *intel_encoder);
 void intel_dp_encoder_destroy(struct drm_encoder *encoder);
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 07/17] drm/i915/dsc: Add a power domain for VDSC on eDP/MIPI DSI

[Manasi Navare]

On Icelake, a separate power well PG2 is created for
VDSC engine used for eDP/MIPI DSI. This patch adds a new
display power domain for Power well 2.

v3:
* Call it POWER_DOMAIN_TRANSCODER_EDP_VDSC (Ville)
* Move it around TRANSCODER power domain defs (Ville)

v2:
* Fix the power well mismatch CI error (Ville)
* Rename as VDSC_PIPE_A (Imre)
* Fix a whitespace (Anusha)
* Fix Comments (Imre)

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
---
 drivers/gpu/drm/i915/intel_display.h    | 1 +
 drivers/gpu/drm/i915/intel_runtime_pm.c | 4 +++-
 2 files changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/i915/intel_display.h b/drivers/gpu/drm/i915/intel_display.h
index 5e253f741d29..b41b06dc8347 100644
--- a/drivers/gpu/drm/i915/intel_display.h
+++ b/drivers/gpu/drm/i915/intel_display.h
@@ -242,6 +242,7 @@ enum intel_display_power_domain {
 	POWER_DOMAIN_TRANSCODER_B,
 	POWER_DOMAIN_TRANSCODER_C,
 	POWER_DOMAIN_TRANSCODER_EDP,
+	POWER_DOMAIN_TRANSCODER_EDP_VDSC,
 	POWER_DOMAIN_TRANSCODER_DSI_A,
 	POWER_DOMAIN_TRANSCODER_DSI_C,
 	POWER_DOMAIN_PORT_DDI_A_LANES,
diff --git a/drivers/gpu/drm/i915/intel_runtime_pm.c b/drivers/gpu/drm/i915/intel_runtime_pm.c
index 1c2de9b69a19..4350a5270423 100644
--- a/drivers/gpu/drm/i915/intel_runtime_pm.c
+++ b/drivers/gpu/drm/i915/intel_runtime_pm.c
@@ -76,6 +76,8 @@ intel_display_power_domain_str(enum intel_display_power_domain domain)
 		return "TRANSCODER_C";
 	case POWER_DOMAIN_TRANSCODER_EDP:
 		return "TRANSCODER_EDP";
+	case POWER_DOMAIN_TRANSCODER_EDP_VDSC:
+		return "TRANSCODER_EDP_VDSC";
 	case POWER_DOMAIN_TRANSCODER_DSI_A:
 		return "TRANSCODER_DSI_A";
 	case POWER_DOMAIN_TRANSCODER_DSI_C:
@@ -2028,9 +2030,9 @@ void intel_display_power_put(struct drm_i915_private *dev_priv,
 	 */
 #define ICL_PW_2_POWER_DOMAINS (			\
 	ICL_PW_3_POWER_DOMAINS |			\
+	BIT_ULL(POWER_DOMAIN_TRANSCODER_EDP_VDSC) |		\
 	BIT_ULL(POWER_DOMAIN_INIT))
 	/*
-	 * - eDP/DSI VDSC
 	 * - KVMR (HW control)
 	 */
 #define ICL_DISPLAY_DC_OFF_POWER_DOMAINS (		\
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 08/17] drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling

[Manasi Navare]

After encoder->pre_enable() hook, after link training sequence is
completed, PPS registers for DSC encoder are configured using the
DSC state parameters in intel_crtc_state as part of DSC enabling
routine in the source. DSC enabling routine is called after
encoder->pre_enable() before enbaling the pipe and after
compression is enabled on the sink.

v7:
* Remove unnecessary comments, leftovers (Ville)
* No need for explicit val &= ~ (Ville)
v6:
intel_dsc_enable to be part of pre_enable hook (Ville)
v5:
* make crtc_state const (Ville)
v4:
* Use cpu_transcoder instead of encoder->type for using EDP transcoder
DSC registers(Ville)
* Keep all PSS regs together (Anusha)

v3:
* Configure Pic_width/2 for each VDSC engine when two VDSC engines per pipe
are used (Manasi)
* Add DSC slice_row_per_frame in PPS16 (Manasi)

v2:
* Enable PG2 power well for VDSC on eDP

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h   |   2 +
 drivers/gpu/drm/i915/intel_ddi.c  |   2 +
 drivers/gpu/drm/i915/intel_vdsc.c | 407 ++++++++++++++++++++++++++++++
 3 files changed, 411 insertions(+)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 183aae996305..9dc8731907af 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3343,6 +3343,8 @@ extern void intel_rps_mark_interactive(struct drm_i915_private *i915,
 				       bool interactive);
 extern bool intel_set_memory_cxsr(struct drm_i915_private *dev_priv,
 				  bool enable);
+void intel_dsc_enable(struct intel_encoder *encoder,
+		      const struct intel_crtc_state *crtc_state);
 
 int i915_reg_read_ioctl(struct drm_device *dev, void *data,
 			struct drm_file *file);
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index fa5ad62cd0db..339be10986d7 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -3144,6 +3144,8 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
 
 	if (!is_mst)
 		intel_ddi_enable_pipe_clock(crtc_state);
+
+	intel_dsc_enable(encoder, crtc_state);
 }
 
 static void intel_ddi_pre_enable_hdmi(struct intel_encoder *encoder,
diff --git a/drivers/gpu/drm/i915/intel_vdsc.c b/drivers/gpu/drm/i915/intel_vdsc.c
index 39baff618ed8..a76e77a3231b 100644
--- a/drivers/gpu/drm/i915/intel_vdsc.c
+++ b/drivers/gpu/drm/i915/intel_vdsc.c
@@ -577,3 +577,410 @@ int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
 
 	return intel_compute_rc_parameters(vdsc_cfg);
 }
+
+static void intel_configure_pps_for_dsc_encoder(struct intel_encoder *encoder,
+						const struct intel_crtc_state *crtc_state)
+{
+	struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+	const struct drm_dsc_config *vdsc_cfg = &crtc_state->dp_dsc_cfg;
+	enum pipe pipe = crtc->pipe;
+	enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
+	u32 pps_val = 0;
+	u32 rc_buf_thresh_dword[4];
+	u32 rc_range_params_dword[8];
+	u8 num_vdsc_instances = (crtc_state->dsc_params.dsc_split) ? 2 : 1;
+	int i = 0;
+
+	/* Populate PICTURE_PARAMETER_SET_0 registers */
+	pps_val = DSC_VER_MAJ | vdsc_cfg->dsc_version_minor <<
+		DSC_VER_MIN_SHIFT |
+		vdsc_cfg->bits_per_component << DSC_BPC_SHIFT |
+		vdsc_cfg->line_buf_depth << DSC_LINE_BUF_DEPTH_SHIFT;
+	if (vdsc_cfg->block_pred_enable)
+		pps_val |= DSC_BLOCK_PREDICTION;
+	if (vdsc_cfg->convert_rgb)
+		pps_val |= DSC_COLOR_SPACE_CONVERSION;
+	if (vdsc_cfg->enable422)
+		pps_val |= DSC_422_ENABLE;
+	if (vdsc_cfg->vbr_enable)
+		pps_val |= DSC_VBR_ENABLE;
+	DRM_INFO("PPS0 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_0, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_0, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_0(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_0(pipe),
+				   pps_val);
+	}
+
+	/* Populate PICTURE_PARAMETER_SET_1 registers */
+	pps_val = 0;
+	pps_val |= DSC_BPP(vdsc_cfg->bits_per_pixel);
+	DRM_INFO("PPS1 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_1, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_1, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_1(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_1(pipe),
+				   pps_val);
+	}
+
+	/* Populate PICTURE_PARAMETER_SET_2 registers */
+	pps_val = 0;
+	pps_val |= DSC_PIC_HEIGHT(vdsc_cfg->pic_height) |
+		DSC_PIC_WIDTH(vdsc_cfg->pic_width / num_vdsc_instances);
+	DRM_INFO("PPS2 = 0x%08x\n", pps_val);
+	if (encoder->type == INTEL_OUTPUT_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_2, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_2, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_2(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_2(pipe),
+				   pps_val);
+	}
+
+	/* Populate PICTURE_PARAMETER_SET_3 registers */
+	pps_val = 0;
+	pps_val |= DSC_SLICE_HEIGHT(vdsc_cfg->slice_height) |
+		DSC_SLICE_WIDTH(vdsc_cfg->slice_width);
+	DRM_INFO("PPS3 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_3, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_3, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_3(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_3(pipe),
+				   pps_val);
+	}
+
+	/* Populate PICTURE_PARAMETER_SET_4 registers */
+	pps_val = 0;
+	pps_val |= DSC_INITIAL_XMIT_DELAY(vdsc_cfg->initial_xmit_delay) |
+		DSC_INITIAL_DEC_DELAY(vdsc_cfg->initial_dec_delay);
+	DRM_INFO("PPS4 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_4, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_4, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_4(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_4(pipe),
+				   pps_val);
+	}
+
+	/* Populate PICTURE_PARAMETER_SET_5 registers */
+	pps_val = 0;
+	pps_val |= DSC_SCALE_INC_INT(vdsc_cfg->scale_increment_interval) |
+		DSC_SCALE_DEC_INT(vdsc_cfg->scale_decrement_interval);
+	DRM_INFO("PPS5 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_5, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_5, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_5(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_5(pipe),
+				   pps_val);
+	}
+
+	/* Populate PICTURE_PARAMETER_SET_6 registers */
+	pps_val = 0;
+	pps_val |= DSC_INITIAL_SCALE_VALUE(vdsc_cfg->initial_scale_value) |
+		DSC_FIRST_LINE_BPG_OFFSET(vdsc_cfg->first_line_bpg_offset) |
+		DSC_FLATNESS_MIN_QP(vdsc_cfg->flatness_min_qp) |
+		DSC_FLATNESS_MAX_QP(vdsc_cfg->flatness_max_qp);
+	DRM_INFO("PPS6 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_6, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_6, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_6(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_6(pipe),
+				   pps_val);
+	}
+
+	/* Populate PICTURE_PARAMETER_SET_7 registers */
+	pps_val = 0;
+	pps_val |= DSC_SLICE_BPG_OFFSET(vdsc_cfg->slice_bpg_offset) |
+		DSC_NFL_BPG_OFFSET(vdsc_cfg->nfl_bpg_offset);
+	DRM_INFO("PPS7 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_7, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_7, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_7(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_7(pipe),
+				   pps_val);
+	}
+
+	/* Populate PICTURE_PARAMETER_SET_8 registers */
+	pps_val = 0;
+	pps_val |= DSC_FINAL_OFFSET(vdsc_cfg->final_offset) |
+		DSC_INITIAL_OFFSET(vdsc_cfg->initial_offset);
+	DRM_INFO("PPS8 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_8, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_8, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_8(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_8(pipe),
+				   pps_val);
+	}
+
+	/* Populate PICTURE_PARAMETER_SET_9 registers */
+	pps_val = 0;
+	pps_val |= DSC_RC_MODEL_SIZE(DSC_RC_MODEL_SIZE_CONST) |
+		DSC_RC_EDGE_FACTOR(DSC_RC_EDGE_FACTOR_CONST);
+	DRM_INFO("PPS9 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_9, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_9, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_9(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_9(pipe),
+				   pps_val);
+	}
+
+	/* Populate PICTURE_PARAMETER_SET_10 registers */
+	pps_val = 0;
+	pps_val |= DSC_RC_QUANT_INC_LIMIT0(vdsc_cfg->rc_quant_incr_limit0) |
+		DSC_RC_QUANT_INC_LIMIT1(vdsc_cfg->rc_quant_incr_limit1) |
+		DSC_RC_TARGET_OFF_HIGH(DSC_RC_TGT_OFFSET_HI_CONST) |
+		DSC_RC_TARGET_OFF_LOW(DSC_RC_TGT_OFFSET_LO_CONST);
+	DRM_INFO("PPS10 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_10, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_10, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_10(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_10(pipe),
+				   pps_val);
+	}
+
+	/* Populate Picture parameter set 16 */
+	pps_val = 0;
+	pps_val |= DSC_SLICE_CHUNK_SIZE(vdsc_cfg->slice_chunk_size) |
+		DSC_SLICE_PER_LINE((vdsc_cfg->pic_width / num_vdsc_instances) /
+				   vdsc_cfg->slice_width) |
+		DSC_SLICE_ROW_PER_FRAME(vdsc_cfg->pic_height /
+					vdsc_cfg->slice_height);
+	DRM_INFO("PPS16 = 0x%08x\n", pps_val);
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_PICTURE_PARAMETER_SET_16, pps_val);
+		/*
+		 * If 2 VDSC instances are needed, configure PPS for second
+		 * VDSC
+		 */
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(DSCC_PICTURE_PARAMETER_SET_16, pps_val);
+	} else {
+		I915_WRITE(ICL_DSC0_PICTURE_PARAMETER_SET_16(pipe), pps_val);
+		if (crtc_state->dsc_params.dsc_split)
+			I915_WRITE(ICL_DSC1_PICTURE_PARAMETER_SET_16(pipe),
+				   pps_val);
+	}
+
+	/* Populate the RC_BUF_THRESH registers */
+	memset(rc_buf_thresh_dword, 0, sizeof(rc_buf_thresh_dword));
+	for (i = 0; i < DSC_NUM_BUF_RANGES - 1; i++) {
+		rc_buf_thresh_dword[i / 4] |= (u32)(vdsc_cfg->rc_buf_thresh[i] <<
+						    BITS_PER_BYTE * (i % 4));
+		DRM_INFO(" RC_BUF_THRESH%d = 0x%08x\n", i,
+			 rc_buf_thresh_dword[i / 4]);
+	}
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_RC_BUF_THRESH_0, rc_buf_thresh_dword[0]);
+		I915_WRITE(DSCA_RC_BUF_THRESH_0_UDW, rc_buf_thresh_dword[1]);
+		I915_WRITE(DSCA_RC_BUF_THRESH_1, rc_buf_thresh_dword[2]);
+		I915_WRITE(DSCA_RC_BUF_THRESH_1_UDW, rc_buf_thresh_dword[3]);
+		if (crtc_state->dsc_params.dsc_split) {
+			I915_WRITE(DSCC_RC_BUF_THRESH_0,
+				   rc_buf_thresh_dword[0]);
+			I915_WRITE(DSCC_RC_BUF_THRESH_0_UDW,
+				   rc_buf_thresh_dword[1]);
+			I915_WRITE(DSCC_RC_BUF_THRESH_1,
+				   rc_buf_thresh_dword[2]);
+			I915_WRITE(DSCC_RC_BUF_THRESH_1_UDW,
+				   rc_buf_thresh_dword[3]);
+		}
+	} else {
+		I915_WRITE(ICL_DSC0_RC_BUF_THRESH_0(pipe),
+			   rc_buf_thresh_dword[0]);
+		I915_WRITE(ICL_DSC0_RC_BUF_THRESH_0_UDW(pipe),
+			   rc_buf_thresh_dword[1]);
+		I915_WRITE(ICL_DSC0_RC_BUF_THRESH_1(pipe),
+			   rc_buf_thresh_dword[2]);
+		I915_WRITE(ICL_DSC0_RC_BUF_THRESH_1_UDW(pipe),
+			   rc_buf_thresh_dword[3]);
+		if (crtc_state->dsc_params.dsc_split) {
+			I915_WRITE(ICL_DSC1_RC_BUF_THRESH_0(pipe),
+				   rc_buf_thresh_dword[0]);
+			I915_WRITE(ICL_DSC1_RC_BUF_THRESH_0_UDW(pipe),
+				   rc_buf_thresh_dword[1]);
+			I915_WRITE(ICL_DSC1_RC_BUF_THRESH_1(pipe),
+				   rc_buf_thresh_dword[2]);
+			I915_WRITE(ICL_DSC1_RC_BUF_THRESH_1_UDW(pipe),
+				   rc_buf_thresh_dword[3]);
+		}
+	}
+
+	/* Populate the RC_RANGE_PARAMETERS registers */
+	memset(rc_range_params_dword, 0, sizeof(rc_range_params_dword));
+	for (i = 0; i < DSC_NUM_BUF_RANGES; i++) {
+		rc_range_params_dword[i / 2] |= (u32)(((vdsc_cfg->rc_range_params[i].range_bpg_offset <<
+							RC_BPG_OFFSET_SHIFT) |
+						       (vdsc_cfg->rc_range_params[i].range_max_qp <<
+							RC_MAX_QP_SHIFT) |
+						       (vdsc_cfg->rc_range_params[i].range_min_qp <<
+							RC_MIN_QP_SHIFT)) << 16 * (i % 2));
+		DRM_INFO(" RC_RANGE_PARAM_%d = 0x%08x\n", i,
+			 rc_range_params_dword[i / 2]);
+	}
+	if (cpu_transcoder == TRANSCODER_EDP) {
+		I915_WRITE(DSCA_RC_RANGE_PARAMETERS_0,
+			   rc_range_params_dword[0]);
+		I915_WRITE(DSCA_RC_RANGE_PARAMETERS_0_UDW,
+			   rc_range_params_dword[1]);
+		I915_WRITE(DSCA_RC_RANGE_PARAMETERS_1,
+			   rc_range_params_dword[2]);
+		I915_WRITE(DSCA_RC_RANGE_PARAMETERS_1_UDW,
+			   rc_range_params_dword[3]);
+		I915_WRITE(DSCA_RC_RANGE_PARAMETERS_2,
+			   rc_range_params_dword[4]);
+		I915_WRITE(DSCA_RC_RANGE_PARAMETERS_2_UDW,
+			   rc_range_params_dword[5]);
+		I915_WRITE(DSCA_RC_RANGE_PARAMETERS_3,
+			   rc_range_params_dword[6]);
+		I915_WRITE(DSCA_RC_RANGE_PARAMETERS_3_UDW,
+			   rc_range_params_dword[7]);
+		if (crtc_state->dsc_params.dsc_split) {
+			I915_WRITE(DSCC_RC_RANGE_PARAMETERS_0,
+				   rc_range_params_dword[0]);
+			I915_WRITE(DSCC_RC_RANGE_PARAMETERS_0_UDW,
+				   rc_range_params_dword[1]);
+			I915_WRITE(DSCC_RC_RANGE_PARAMETERS_1,
+				   rc_range_params_dword[2]);
+			I915_WRITE(DSCC_RC_RANGE_PARAMETERS_1_UDW,
+				   rc_range_params_dword[3]);
+			I915_WRITE(DSCC_RC_RANGE_PARAMETERS_2,
+				   rc_range_params_dword[4]);
+			I915_WRITE(DSCC_RC_RANGE_PARAMETERS_2_UDW,
+				   rc_range_params_dword[5]);
+			I915_WRITE(DSCC_RC_RANGE_PARAMETERS_3,
+				   rc_range_params_dword[6]);
+			I915_WRITE(DSCC_RC_RANGE_PARAMETERS_3_UDW,
+				   rc_range_params_dword[7]);
+		}
+	} else {
+		I915_WRITE(ICL_DSC0_RC_RANGE_PARAMETERS_0(pipe),
+			   rc_range_params_dword[0]);
+		I915_WRITE(ICL_DSC0_RC_RANGE_PARAMETERS_0_UDW(pipe),
+			   rc_range_params_dword[1]);
+		I915_WRITE(ICL_DSC0_RC_RANGE_PARAMETERS_1(pipe),
+			   rc_range_params_dword[2]);
+		I915_WRITE(ICL_DSC0_RC_RANGE_PARAMETERS_1_UDW(pipe),
+			   rc_range_params_dword[3]);
+		I915_WRITE(ICL_DSC0_RC_RANGE_PARAMETERS_2(pipe),
+			   rc_range_params_dword[4]);
+		I915_WRITE(ICL_DSC0_RC_RANGE_PARAMETERS_2_UDW(pipe),
+			   rc_range_params_dword[5]);
+		I915_WRITE(ICL_DSC0_RC_RANGE_PARAMETERS_3(pipe),
+			   rc_range_params_dword[6]);
+		I915_WRITE(ICL_DSC0_RC_RANGE_PARAMETERS_3_UDW(pipe),
+			   rc_range_params_dword[7]);
+		if (crtc_state->dsc_params.dsc_split) {
+			I915_WRITE(ICL_DSC1_RC_RANGE_PARAMETERS_0(pipe),
+				   rc_range_params_dword[0]);
+			I915_WRITE(ICL_DSC1_RC_RANGE_PARAMETERS_0_UDW(pipe),
+				   rc_range_params_dword[1]);
+			I915_WRITE(ICL_DSC1_RC_RANGE_PARAMETERS_1(pipe),
+				   rc_range_params_dword[2]);
+			I915_WRITE(ICL_DSC1_RC_RANGE_PARAMETERS_1_UDW(pipe),
+				   rc_range_params_dword[3]);
+			I915_WRITE(ICL_DSC1_RC_RANGE_PARAMETERS_2(pipe),
+				   rc_range_params_dword[4]);
+			I915_WRITE(ICL_DSC1_RC_RANGE_PARAMETERS_2_UDW(pipe),
+				   rc_range_params_dword[5]);
+			I915_WRITE(ICL_DSC1_RC_RANGE_PARAMETERS_3(pipe),
+				   rc_range_params_dword[6]);
+			I915_WRITE(ICL_DSC1_RC_RANGE_PARAMETERS_3_UDW(pipe),
+				   rc_range_params_dword[7]);
+		}
+	}
+}
+
+void intel_dsc_enable(struct intel_encoder *encoder,
+		      const struct intel_crtc_state *crtc_state)
+{
+	if (!crtc_state->dsc_params.compression_enable)
+		return;
+
+	intel_configure_pps_for_dsc_encoder(encoder, crtc_state);
+}
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 09/17] drm/i915/dp: Use the existing write_infoframe() for DSC PPS SDPs

[Manasi Navare]

Infoframes are used to send secondary data packets. This patch
adds support for DSC Picture parameter set secondary data packets
in the existing write_infoframe helpers.

v3:
* Unused variables cleanup (Ville)
v2:
* Rebase on drm-tip (Manasi)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
---
 drivers/gpu/drm/i915/i915_reg.h   |  1 +
 drivers/gpu/drm/i915/intel_hdmi.c | 21 +++++++++++++++++++--
 2 files changed, 20 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 47baf2fe8f71..eadd880b0ef6 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -4570,6 +4570,7 @@ enum {
  * of the infoframe structure specified by CEA-861. */
 #define   VIDEO_DIP_DATA_SIZE	32
 #define   VIDEO_DIP_VSC_DATA_SIZE	36
+#define   VIDEO_DIP_PPS_DATA_SIZE	132
 #define VIDEO_DIP_CTL		_MMIO(0x61170)
 /* Pre HSW: */
 #define   VIDEO_DIP_ENABLE		(1 << 31)
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index e2c6a2b3e8f2..07e803a604bd 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -115,6 +115,8 @@ static u32 hsw_infoframe_enable(unsigned int type)
 	switch (type) {
 	case DP_SDP_VSC:
 		return VIDEO_DIP_ENABLE_VSC_HSW;
+	case DP_SDP_PPS:
+		return VDIP_ENABLE_PPS;
 	case HDMI_INFOFRAME_TYPE_AVI:
 		return VIDEO_DIP_ENABLE_AVI_HSW;
 	case HDMI_INFOFRAME_TYPE_SPD:
@@ -136,6 +138,8 @@ hsw_dip_data_reg(struct drm_i915_private *dev_priv,
 	switch (type) {
 	case DP_SDP_VSC:
 		return HSW_TVIDEO_DIP_VSC_DATA(cpu_transcoder, i);
+	case DP_SDP_PPS:
+		return ICL_VIDEO_DIP_PPS_DATA(cpu_transcoder, i);
 	case HDMI_INFOFRAME_TYPE_AVI:
 		return HSW_TVIDEO_DIP_AVI_DATA(cpu_transcoder, i);
 	case HDMI_INFOFRAME_TYPE_SPD:
@@ -148,6 +152,18 @@ hsw_dip_data_reg(struct drm_i915_private *dev_priv,
 	}
 }
 
+static int hsw_dip_data_size(unsigned int type)
+{
+	switch (type) {
+	case DP_SDP_VSC:
+		return VIDEO_DIP_VSC_DATA_SIZE;
+	case DP_SDP_PPS:
+		return VIDEO_DIP_PPS_DATA_SIZE;
+	default:
+		return VIDEO_DIP_DATA_SIZE;
+	}
+}
+
 static void g4x_write_infoframe(struct intel_encoder *encoder,
 				const struct intel_crtc_state *crtc_state,
 				unsigned int type,
@@ -382,11 +398,12 @@ static void hsw_write_infoframe(struct intel_encoder *encoder,
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
 	enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
 	i915_reg_t ctl_reg = HSW_TVIDEO_DIP_CTL(cpu_transcoder);
-	int data_size = type == DP_SDP_VSC ?
-		VIDEO_DIP_VSC_DATA_SIZE : VIDEO_DIP_DATA_SIZE;
+	int data_size;
 	int i;
 	u32 val = I915_READ(ctl_reg);
 
+	data_size = hsw_dip_data_size(type);
+
 	val &= ~hsw_infoframe_enable(type);
 	I915_WRITE(ctl_reg, val);
 
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 10/17] drm/i915/dp: Populate DSC PPS SDP and send PPS infoframes

[Manasi Navare]

DSC PPS secondary data packet infoframes are filled with
DSC picure parameter set metadata according to the DSC standard.
These infoframes are sent to the sink device and used during DSC
decoding.

v3:
* Rename to intel_dp_write_pps_sdp (Ville)
* Use const intel_crtc_state (Ville)
v2:
* Rebase ond drm-tip

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
---
 drivers/gpu/drm/i915/intel_vdsc.c | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_vdsc.c b/drivers/gpu/drm/i915/intel_vdsc.c
index a76e77a3231b..56290093d43f 100644
--- a/drivers/gpu/drm/i915/intel_vdsc.c
+++ b/drivers/gpu/drm/i915/intel_vdsc.c
@@ -976,6 +976,25 @@ static void intel_configure_pps_for_dsc_encoder(struct intel_encoder *encoder,
 	}
 }
 
+static void intel_dp_write_dsc_pps_sdp(struct intel_encoder *encoder,
+				       const struct intel_crtc_state *crtc_state)
+{
+	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
+	struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp);
+	const struct drm_dsc_config *vdsc_cfg = &crtc_state->dp_dsc_cfg;
+	struct drm_dsc_pps_infoframe dp_dsc_pps_sdp;
+
+	/* Prepare DP SDP PPS header as per DP 1.4 spec, Table 2-123 */
+	drm_dsc_dp_pps_header_init(&dp_dsc_pps_sdp);
+
+	/* Fill the PPS payload bytes as per DSC spec 1.2 Table 4-1 */
+	drm_dsc_pps_infoframe_pack(&dp_dsc_pps_sdp, vdsc_cfg);
+
+	intel_dig_port->write_infoframe(encoder, crtc_state,
+					DP_SDP_PPS, &dp_dsc_pps_sdp,
+					sizeof(dp_dsc_pps_sdp));
+}
+
 void intel_dsc_enable(struct intel_encoder *encoder,
 		      const struct intel_crtc_state *crtc_state)
 {
@@ -983,4 +1002,6 @@ void intel_dsc_enable(struct intel_encoder *encoder,
 		return;
 
 	intel_configure_pps_for_dsc_encoder(encoder, crtc_state);
+
+	intel_dp_write_dsc_pps_sdp(encoder, crtc_state);
 }
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 11/17] drm/i915/dp: Configure Display stream splitter registers during DSC enable

[Manasi Navare]

Display Stream Splitter registers need to be programmed to enable
the joiner if two DSC engines are used and also to enable
the left and the right DSC engines. This happens as part of
the DSC enabling routine in the source in atomic commit.

v4:
* Remove redundant comment (Ville)
v3:
* Use cpu_transcoder instead of encoder->type (Ville)
v2:
* Rebase (Manasi)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intelcom>
---
 drivers/gpu/drm/i915/intel_vdsc.c | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_vdsc.c b/drivers/gpu/drm/i915/intel_vdsc.c
index 56290093d43f..38f391329b8c 100644
--- a/drivers/gpu/drm/i915/intel_vdsc.c
+++ b/drivers/gpu/drm/i915/intel_vdsc.c
@@ -998,10 +998,32 @@ static void intel_dp_write_dsc_pps_sdp(struct intel_encoder *encoder,
 void intel_dsc_enable(struct intel_encoder *encoder,
 		      const struct intel_crtc_state *crtc_state)
 {
+	struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+	enum pipe pipe = crtc->pipe;
+	i915_reg_t dss_ctl1_reg, dss_ctl2_reg;
+	u32 dss_ctl1_val = 0;
+	u32 dss_ctl2_val = 0;
+
 	if (!crtc_state->dsc_params.compression_enable)
 		return;
 
 	intel_configure_pps_for_dsc_encoder(encoder, crtc_state);
 
 	intel_dp_write_dsc_pps_sdp(encoder, crtc_state);
+
+	if (crtc_state->cpu_transcoder == TRANSCODER_EDP) {
+		dss_ctl1_reg = DSS_CTL1;
+		dss_ctl2_reg = DSS_CTL2;
+	} else {
+		dss_ctl1_reg = ICL_PIPE_DSS_CTL1(pipe);
+		dss_ctl2_reg = ICL_PIPE_DSS_CTL2(pipe);
+	}
+	dss_ctl2_val |= LEFT_BRANCH_VDSC_ENABLE;
+	if (crtc_state->dsc_params.dsc_split) {
+		dss_ctl2_val |= RIGHT_BRANCH_VDSC_ENABLE;
+		dss_ctl1_val |= JOINER_ENABLE;
+	}
+	I915_WRITE(dss_ctl1_reg, dss_ctl1_val);
+	I915_WRITE(dss_ctl2_reg, dss_ctl2_val);
 }
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 12/17] drm/i915/dp: Disable DSC in source by disabling DSS CTL bits

[Manasi Navare]

1. Disable Left/right VDSC branch in DSS Ctrl reg
    depending on the number of VDSC engines being used
2. Disable joiner in DSS Ctrl reg

v4:
* Remove encoder, make crtc_state const (Ville)
v3 (From Manasi):
* Add Disable PG2 for VDSC on eDP
v2 (From Manasi):
* Use old_crtc_state to find dsc params
* Add a condition to disable only if
dsc state compression is enabled
* Use correct DSS CTL regs

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h      |  1 +
 drivers/gpu/drm/i915/intel_display.c |  2 ++
 drivers/gpu/drm/i915/intel_vdsc.c    | 31 ++++++++++++++++++++++++++++
 3 files changed, 34 insertions(+)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 9dc8731907af..5fe5d8f2d061 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -3345,6 +3345,7 @@ extern bool intel_set_memory_cxsr(struct drm_i915_private *dev_priv,
 				  bool enable);
 void intel_dsc_enable(struct intel_encoder *encoder,
 		      const struct intel_crtc_state *crtc_state);
+void intel_dsc_disable(const struct intel_crtc_state *crtc_state);
 
 int i915_reg_read_ioctl(struct drm_device *dev, void *data,
 			struct drm_file *file);
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 69bb0b75a806..7a221fb9ca66 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -5889,6 +5889,8 @@ static void haswell_crtc_disable(struct intel_crtc_state *old_crtc_state,
 	if (!transcoder_is_dsi(cpu_transcoder))
 		intel_ddi_disable_transcoder_func(old_crtc_state);
 
+	intel_dsc_disable(old_crtc_state);
+
 	if (INTEL_GEN(dev_priv) >= 9)
 		skylake_scaler_disable(intel_crtc);
 	else
diff --git a/drivers/gpu/drm/i915/intel_vdsc.c b/drivers/gpu/drm/i915/intel_vdsc.c
index 38f391329b8c..f1892f690220 100644
--- a/drivers/gpu/drm/i915/intel_vdsc.c
+++ b/drivers/gpu/drm/i915/intel_vdsc.c
@@ -1027,3 +1027,34 @@ void intel_dsc_enable(struct intel_encoder *encoder,
 	I915_WRITE(dss_ctl1_reg, dss_ctl1_val);
 	I915_WRITE(dss_ctl2_reg, dss_ctl2_val);
 }
+
+void intel_dsc_disable(const struct intel_crtc_state *old_crtc_state)
+{
+	struct intel_crtc *crtc = to_intel_crtc(old_crtc_state->base.crtc);
+	struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
+	enum pipe pipe = crtc->pipe;
+	i915_reg_t dss_ctl1_reg, dss_ctl2_reg;
+	u32 dss_ctl1_val = 0, dss_ctl2_val = 0;
+
+	if (!old_crtc_state->dsc_params.compression_enable)
+		return;
+
+	if (old_crtc_state->cpu_transcoder == TRANSCODER_EDP) {
+		dss_ctl1_reg = DSS_CTL1;
+		dss_ctl2_reg = DSS_CTL2;
+	} else {
+		dss_ctl1_reg = ICL_PIPE_DSS_CTL1(pipe);
+		dss_ctl2_reg = ICL_PIPE_DSS_CTL2(pipe);
+	}
+	dss_ctl1_val = I915_READ(dss_ctl1_reg);
+	if (dss_ctl1_val & JOINER_ENABLE)
+		dss_ctl1_val &= ~JOINER_ENABLE;
+	I915_WRITE(dss_ctl1_reg, dss_ctl1_val);
+
+	dss_ctl2_val = I915_READ(dss_ctl2_reg);
+	if (dss_ctl2_val & LEFT_BRANCH_VDSC_ENABLE ||
+	    dss_ctl2_val & RIGHT_BRANCH_VDSC_ENABLE)
+		dss_ctl2_val &= ~(LEFT_BRANCH_VDSC_ENABLE |
+				  RIGHT_BRANCH_VDSC_ENABLE);
+	I915_WRITE(dss_ctl2_reg, dss_ctl2_val);
+}
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 13/17] drm/i915/dsc: Enable and disable appropriate power wells for VDSC

[Manasi Navare]

A separate power well 2 (PG2) is required for VDSC on eDP transcoder
whereas all other transcoders use the power wells associated with the
transcoders for VDSC.
This patch adds a helper to obtain correct power domain depending on
transcoder being used and enables/disables the power wells during
VDSC enabling/disabling.

v4:
* Get VDSC power domain only if compression en is set
in crtc_state (Ville, Imre)
v3:
* Call it intel_dsc_power_domain, add to
intel_ddi_get_power_domains (Ville)
v2:
* Fix tabs, const crtc_state, fix comments (Ville)

Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
---
 drivers/gpu/drm/i915/intel_ddi.c  |  6 ++++++
 drivers/gpu/drm/i915/intel_drv.h  |  2 ++
 drivers/gpu/drm/i915/intel_vdsc.c | 26 ++++++++++++++++++++++++++
 3 files changed, 34 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index 339be10986d7..6533624226a7 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -2154,6 +2154,12 @@ static u64 intel_ddi_get_power_domains(struct intel_encoder *encoder,
 	    intel_port_is_tc(dev_priv, encoder->port))
 		domains |= BIT_ULL(intel_ddi_main_link_aux_domain(dig_port));
 
+	/*
+	 * VDSC power is needed when DSC is enabled
+	 */
+	if (crtc_state->dsc_params.compression_enable)
+		domains |= BIT_ULL(intel_dsc_power_domain(crtc_state));
+
 	return domains;
 }
 
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index fa452fbb16c6..b5693cac26d7 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -1858,6 +1858,8 @@ uint8_t intel_dp_dsc_get_slice_count(struct intel_dp *intel_dp, int mode_clock,
 /* intel_vdsc.c */
 int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
 				struct intel_crtc_state *pipe_config);
+enum intel_display_power_domain
+intel_dsc_power_domain(const struct intel_crtc_state *crtc_state);
 
 static inline unsigned int intel_dp_unused_lane_mask(int lane_count)
 {
diff --git a/drivers/gpu/drm/i915/intel_vdsc.c b/drivers/gpu/drm/i915/intel_vdsc.c
index f1892f690220..0696deaf75cb 100644
--- a/drivers/gpu/drm/i915/intel_vdsc.c
+++ b/drivers/gpu/drm/i915/intel_vdsc.c
@@ -578,6 +578,24 @@ int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
 	return intel_compute_rc_parameters(vdsc_cfg);
 }
 
+enum intel_display_power_domain
+intel_dsc_power_domain(const struct intel_crtc_state *crtc_state)
+{
+	enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
+
+	/*
+	 * On ICL VDSC/joining for eDP transcoder uses a separate power well PW2
+	 * This requires POWER_DOMAIN_TRANSCODER_EDP_VDSC power domain.
+	 * For any other transcoder, VDSC/joining uses the power well associated
+	 * with the pipe/transcoder in use. Hence another reference on the
+	 * transcoder power domain will suffice.
+	 */
+	if (cpu_transcoder == TRANSCODER_EDP)
+		return POWER_DOMAIN_TRANSCODER_EDP_VDSC;
+	else
+		return POWER_DOMAIN_TRANSCODER(cpu_transcoder);
+}
+
 static void intel_configure_pps_for_dsc_encoder(struct intel_encoder *encoder,
 						const struct intel_crtc_state *crtc_state)
 {
@@ -1008,6 +1026,10 @@ void intel_dsc_enable(struct intel_encoder *encoder,
 	if (!crtc_state->dsc_params.compression_enable)
 		return;
 
+	/* Enable Power wells for VDSC/joining */
+	intel_display_power_get(dev_priv,
+				intel_dsc_power_domain(crtc_state));
+
 	intel_configure_pps_for_dsc_encoder(encoder, crtc_state);
 
 	intel_dp_write_dsc_pps_sdp(encoder, crtc_state);
@@ -1057,4 +1079,8 @@ void intel_dsc_disable(const struct intel_crtc_state *old_crtc_state)
 		dss_ctl2_val &= ~(LEFT_BRANCH_VDSC_ENABLE |
 				  RIGHT_BRANCH_VDSC_ENABLE);
 	I915_WRITE(dss_ctl2_reg, dss_ctl2_val);
+
+	/* Disable Power wells for VDSC/joining */
+	intel_display_power_put(dev_priv,
+				intel_dsc_power_domain(old_crtc_state));
 }
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 14/17] i915/dp/fec: Add fec_enable to the crtc state.

[Manasi Navare]

From: Anusha Srivatsa <anusha.srivatsa@intel.com>

For DP 1.4 and above, Display Stream compression can be
enabled only if Forward Error Correctin can be performed.

Add a crtc state for FEC. Currently, the state
is determined by platform, DP and DSC being
enabled. Moving forward we can use the state
to have error correction on other scenarios too
if needed.

v2:
- Control compression_enable with the fec_enable
parameter in crtc state and with intel_dp_supports_fec()
(Ville)

- intel_dp_can_fec()/intel_dp_supports_fec()(manasi)

v3: Check for FEC support along with setting crtc state.

v4: add checks to intel_dp_source_supports_dsc.(manasi)
- Move intel_dp_supports_fec() closer to
intel_dp_supports_dsc() (Anusha)

v5: Move fec check to intel_dp_supports_dsc(Ville)

v6: Remove warning. rebase.

v7: change crtc state to include DP sink and fec capability
of source.(Manasi)

v8: Set fec_enable in crtc in intel_dp_compute_config().

v9 (From Manasi):
* Combine the !edp and !fec_support check
* Derive dev_priv from intel_dp directly

v10 (From Manasi):
* Rebase

Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
---
 drivers/gpu/drm/i915/intel_dp.c  | 28 +++++++++++++++++++++++-----
 drivers/gpu/drm/i915/intel_drv.h |  3 +++
 2 files changed, 26 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 4e65dd1a6c07..38a6e82153fd 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -545,7 +545,7 @@ intel_dp_mode_valid(struct drm_connector *connector,
 			dsc_slice_count =
 				drm_dp_dsc_sink_max_slice_count(intel_dp->dsc_dpcd,
 								true);
-		} else {
+		} else if (drm_dp_sink_supports_fec(intel_dp->fec_capable)) {
 			dsc_max_output_bpp =
 				intel_dp_dsc_get_output_bpp(max_link_clock,
 							    max_lanes,
@@ -1710,14 +1710,26 @@ struct link_config_limits {
 	int min_bpp, max_bpp;
 };
 
-static bool intel_dp_source_supports_dsc(struct intel_dp *intel_dp,
+static bool intel_dp_source_supports_fec(struct intel_dp *intel_dp,
 					 const struct intel_crtc_state *pipe_config)
 {
 	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
 
-	/* FIXME: FEC needed for external DP until then reject DSC on DP */
-	if (!intel_dp_is_edp(intel_dp))
-		return false;
+	return INTEL_GEN(dev_priv) >= 11 &&
+		pipe_config->cpu_transcoder != TRANSCODER_A;
+}
+
+static bool intel_dp_supports_fec(struct intel_dp *intel_dp,
+				  const struct intel_crtc_state *pipe_config)
+{
+	return intel_dp_source_supports_fec(intel_dp, pipe_config) &&
+		drm_dp_sink_supports_fec(intel_dp->fec_capable);
+}
+
+static bool intel_dp_source_supports_dsc(struct intel_dp *intel_dp,
+					 const struct intel_crtc_state *pipe_config)
+{
+	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
 
 	return INTEL_GEN(dev_priv) >= 10 &&
 		pipe_config->cpu_transcoder != TRANSCODER_A;
@@ -1726,6 +1738,9 @@ static bool intel_dp_source_supports_dsc(struct intel_dp *intel_dp,
 static bool intel_dp_supports_dsc(struct intel_dp *intel_dp,
 				  const struct intel_crtc_state *pipe_config)
 {
+	if (!intel_dp_is_edp(intel_dp) && !pipe_config->fec_enable)
+		return false;
+
 	return intel_dp_source_supports_dsc(intel_dp, pipe_config) &&
 		drm_dp_sink_supports_dsc(intel_dp->dsc_dpcd);
 }
@@ -2129,6 +2144,9 @@ intel_dp_compute_config(struct intel_encoder *encoder,
 	if (adjusted_mode->flags & DRM_MODE_FLAG_DBLCLK)
 		return false;
 
+	pipe_config->fec_enable = !intel_dp_is_edp(intel_dp) &&
+				  intel_dp_supports_fec(intel_dp, pipe_config);
+
 	if (!intel_dp_compute_link_config(encoder, pipe_config, conn_state))
 		return false;
 
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index b5693cac26d7..8c582d53c00a 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -946,6 +946,9 @@ struct intel_crtc_state {
 		u8 slice_count;
 	} dsc_params;
 	struct drm_dsc_config dp_dsc_cfg;
+
+	/* Forward Error correction State */
+	bool fec_enable;
 };
 
 struct intel_crtc {
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 15/17] drm/i915/fec: Set FEC_READY in FEC_CONFIGURATION

[Manasi Navare]

From: Anusha Srivatsa <anusha.srivatsa@intel.com>

If the panel supports FEC, the driver has to
set the FEC_READY bit in the dpcd register:
FEC_CONFIGURATION.

This has to happen before link training.

v2: s/intel_dp_set_fec_ready/intel_dp_sink_set_fec_ready
   - change commit message. (Gaurav)

v3: rebased. (r-b Manasi)

v4: Use fec crtc state, before setting FEC_READY
bit. (Anusha)

v5: Move to intel_ddi.c
- Make the function static (Anusha)

v6: Dont pass state as a separate argument (Ville)

v7: (From Manasi)
* Correct the debug print (Ville)

Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
---
 drivers/gpu/drm/i915/intel_ddi.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index 6533624226a7..4c74bbe1cf73 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -3102,6 +3102,16 @@ static void icl_program_mg_dp_mode(struct intel_digital_port *intel_dig_port)
 	I915_WRITE(MG_DP_MODE(port, 1), ln1);
 }
 
+static void intel_dp_sink_set_fec_ready(struct intel_dp *intel_dp,
+					const struct intel_crtc_state *crtc_state)
+{
+	if (!crtc_state->fec_enable)
+		return;
+
+	if (drm_dp_dpcd_writeb(&intel_dp->aux, DP_FEC_CONFIGURATION, DP_FEC_READY) <= 0)
+		DRM_DEBUG_KMS("Failed to set FEC_READY in the sink\n");
+}
+
 static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
 				    const struct intel_crtc_state *crtc_state,
 				    const struct drm_connector_state *conn_state)
@@ -3142,6 +3152,7 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
 		intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
 	intel_dp_sink_set_decompression_state(intel_dp, crtc_state,
 					      true);
+	intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
 	intel_dp_start_link_train(intel_dp);
 	if (port != PORT_A || INTEL_GEN(dev_priv) >= 9)
 		intel_dp_stop_link_train(intel_dp);
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 16/17] i915/dp/fec: Configure the Forward Error Correction bits.

[Manasi Navare]

From: Anusha Srivatsa <anusha.srivatsa@intel.com>

If FEC is supported, the corresponding
DP_TP_CTL register bits have to be configured.

The driver has to program the FEC_ENABLE in DP_TP_CTL[30] register
and wait till FEC_STATUS in DP_TP_CTL[28] is 1.
Also add the warn message to make sure that the control
register is already active while enabling FEC.

v2:
- Change commit message. Configure fec state after
  link training (Manasi, Gaurav)
- Remove redundent checks (Manasi)
- Remove the registers that get added automagically (Anusha)

v3: s/intel_dp_set_fec_state()/intel_dp_enable_fec_state() (Gaurav)

v4: rebased.

v5:
- Move the code to the proper spot, according to spec.(Ville)
- Use fec state as a check too.

v6: Pass intel_encoder, instead of intel_dp. (Ville)

v7: Remove unwanted comments (Manasi)

Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
---
 drivers/gpu/drm/i915/i915_reg.h  |  2 ++
 drivers/gpu/drm/i915/intel_ddi.c | 23 +++++++++++++++++++++++
 2 files changed, 25 insertions(+)

diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index eadd880b0ef6..d3ef97915455 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -9198,6 +9198,7 @@ enum skl_power_gate {
 #define _DP_TP_CTL_B			0x64140
 #define DP_TP_CTL(port) _MMIO_PORT(port, _DP_TP_CTL_A, _DP_TP_CTL_B)
 #define  DP_TP_CTL_ENABLE			(1 << 31)
+#define  DP_TP_CTL_FEC_ENABLE			(1 << 30)
 #define  DP_TP_CTL_MODE_SST			(0 << 27)
 #define  DP_TP_CTL_MODE_MST			(1 << 27)
 #define  DP_TP_CTL_FORCE_ACT			(1 << 25)
@@ -9216,6 +9217,7 @@ enum skl_power_gate {
 #define _DP_TP_STATUS_A			0x64044
 #define _DP_TP_STATUS_B			0x64144
 #define DP_TP_STATUS(port) _MMIO_PORT(port, _DP_TP_STATUS_A, _DP_TP_STATUS_B)
+#define  DP_TP_STATUS_FEC_ENABLE_LIVE		(1 << 28)
 #define  DP_TP_STATUS_IDLE_DONE			(1 << 25)
 #define  DP_TP_STATUS_ACT_SENT			(1 << 24)
 #define  DP_TP_STATUS_MODE_STATUS_MST		(1 << 23)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index 4c74bbe1cf73..12acdb08a750 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -3112,6 +3112,27 @@ static void intel_dp_sink_set_fec_ready(struct intel_dp *intel_dp,
 		DRM_DEBUG_KMS("Failed to set FEC_READY in the sink\n");
 }
 
+static void intel_ddi_enable_fec(struct intel_encoder *encoder,
+				 const struct intel_crtc_state *crtc_state)
+{
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+	enum port port = encoder->port;
+	u32 val;
+
+	if (!crtc_state->fec_enable)
+		return;
+
+	val = I915_READ(DP_TP_CTL(port));
+	val |= DP_TP_CTL_FEC_ENABLE;
+	I915_WRITE(DP_TP_CTL(port), val);
+
+	if (intel_wait_for_register(dev_priv, DP_TP_STATUS(port),
+				    DP_TP_STATUS_FEC_ENABLE_LIVE,
+				    DP_TP_STATUS_FEC_ENABLE_LIVE,
+				    1))
+		DRM_ERROR("Timed out waiting for FEC Enable Status\n");
+}
+
 static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
 				    const struct intel_crtc_state *crtc_state,
 				    const struct drm_connector_state *conn_state)
@@ -3157,6 +3178,8 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
 	if (port != PORT_A || INTEL_GEN(dev_priv) >= 9)
 		intel_dp_stop_link_train(intel_dp);
 
+	intel_ddi_enable_fec(encoder, crtc_state);
+
 	icl_enable_phy_clock_gating(dig_port);
 
 	if (!is_mst)
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v13 17/17] drm/i915/fec: Disable FEC state.

[Manasi Navare]

From: Anusha Srivatsa <anusha.srivatsa@intel.com>

Set the suitable bits in DP_TP_CTL to stop
bit correction when DSC is disabled.

v2:
- rebased.
- Add additional check for compression state. (Gaurav)

v3: rebased.

v4:
- Move the code to the proper spot according to spec (Ville)
- Use proper checks (manasi)

v5: Remove unnecessary checks (Ville)

v6: Resolve warnings. Add crtc_state as an argument to
intel_disable_ddi_buf(). (Manasi)

Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
---
 drivers/gpu/drm/i915/intel_ddi.c | 28 ++++++++++++++++++++++++----
 1 file changed, 24 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index 12acdb08a750..61d7145f93bf 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -3133,6 +3133,22 @@ static void intel_ddi_enable_fec(struct intel_encoder *encoder,
 		DRM_ERROR("Timed out waiting for FEC Enable Status\n");
 }
 
+static void intel_ddi_disable_fec_state(struct intel_encoder *encoder,
+					const struct intel_crtc_state *crtc_state)
+{
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+	enum port port = encoder->port;
+	u32 val;
+
+	if (!crtc_state->fec_enable)
+		return;
+
+	val = I915_READ(DP_TP_CTL(port));
+	val &= ~DP_TP_CTL_FEC_ENABLE;
+	I915_WRITE(DP_TP_CTL(port), val);
+	POSTING_READ(DP_TP_CTL(port));
+}
+
 static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
 				    const struct intel_crtc_state *crtc_state,
 				    const struct drm_connector_state *conn_state)
@@ -3272,7 +3288,8 @@ static void intel_ddi_pre_enable(struct intel_encoder *encoder,
 	}
 }
 
-static void intel_disable_ddi_buf(struct intel_encoder *encoder)
+static void intel_disable_ddi_buf(struct intel_encoder *encoder,
+				  const struct intel_crtc_state *crtc_state)
 {
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
 	enum port port = encoder->port;
@@ -3291,6 +3308,9 @@ static void intel_disable_ddi_buf(struct intel_encoder *encoder)
 	val |= DP_TP_CTL_LINK_TRAIN_PAT1;
 	I915_WRITE(DP_TP_CTL(port), val);
 
+	/* Disable FEC in DP Sink */
+	intel_ddi_disable_fec_state(encoder, crtc_state);
+
 	if (wait)
 		intel_wait_ddi_buf_idle(dev_priv, port);
 }
@@ -3314,7 +3334,7 @@ static void intel_ddi_post_disable_dp(struct intel_encoder *encoder,
 		intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);
 	}
 
-	intel_disable_ddi_buf(encoder);
+	intel_disable_ddi_buf(encoder, old_crtc_state);
 
 	intel_edp_panel_vdd_on(intel_dp);
 	intel_edp_panel_off(intel_dp);
@@ -3337,7 +3357,7 @@ static void intel_ddi_post_disable_hdmi(struct intel_encoder *encoder,
 
 	intel_ddi_disable_pipe_clock(old_crtc_state);
 
-	intel_disable_ddi_buf(encoder);
+	intel_disable_ddi_buf(encoder, old_crtc_state);
 
 	intel_display_power_put(dev_priv, dig_port->ddi_io_power_domain);
 
@@ -3388,7 +3408,7 @@ void intel_ddi_fdi_post_disable(struct intel_encoder *encoder,
 	val &= ~FDI_RX_ENABLE;
 	I915_WRITE(FDI_RX_CTL(PIPE_A), val);
 
-	intel_disable_ddi_buf(encoder);
+	intel_disable_ddi_buf(encoder, old_crtc_state);
 	intel_ddi_clk_disable(encoder);
 
 	val = I915_READ(FDI_RX_MISC(PIPE_A));
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

✗ Fi.CI.BAT: failure for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state

[Patchwork]

== Series Details ==

Series: series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state
URL   : https://patchwork.freedesktop.org/series/53184/
State : failure

== Summary ==

Applying: drm/i915/dp: Add DSC params and DSC config to intel_crtc_state
Applying: drm/i915/dp: Compute DSC pipe config in atomic check
Using index info to reconstruct a base tree...
M	drivers/gpu/drm/i915/intel_display.c
M	drivers/gpu/drm/i915/intel_display.h
Falling back to patching base and 3-way merge...
Auto-merging drivers/gpu/drm/i915/intel_display.h
CONFLICT (content): Merge conflict in drivers/gpu/drm/i915/intel_display.h
Auto-merging drivers/gpu/drm/i915/intel_display.c
error: Failed to merge in the changes.
Patch failed at 0002 drm/i915/dp: Compute DSC pipe config in atomic check
Use 'git am --show-current-patch' to see the failed patch
When you have resolved this problem, run "git am --continue".
If you prefer to skip this patch, run "git am --skip" instead.
To restore the original branch and stop patching, run "git am --abort".

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[PATCH v14 02/17] drm/i915/dp: Compute DSC pipe config in atomic check

[Manasi Navare]

DSC params like the enable, compressed bpp, slice count and
dsc_split are added to the intel_crtc_state. These parameters
are set based on the requested mode and available link parameters
during the pipe configuration in atomic check phase.
These values are then later used to populate the remaining DSC
and RC parameters before enbaling DSC in atomic commit.

v15:
* Rebase over drm-tip
v14:
Remove leftovers, use dsc_bpc, refine dsc_compute_config (Ville)
v13:
* Compute DSC bpc only when DSC is req to be enabled (Ville)
v12:
* Override bpp with dsc dpcd color depth (Manasi)
v11:
* Const crtc_state, reject DSC on DP without FEC (Ville)
* Dont set dsc_split to false (Ville)
v10:
* Add a helper for dp_dsc support (Ville)
* Set pipe_config to max bpp, link params for DSC for now (Ville)
* Compute bpp - use dp dsc support helper (Ville)
v9:
* Rebase on top of drm-tip that now uses fast_narrow config
for edp (Manasi)
v8:
* Check for DSC bpc not 0 (manasi)

v7:
* Fix indentation in compute_m_n (Manasi)

v6 (From Gaurav):
* Remove function call of intel_dp_compute_dsc_params() and
invoke intel_dp_compute_dsc_params() in the patch where
it is defined to fix compilation warning (Gaurav)

v5:
Add drm_dsc_cfg in intel_crtc_state (Manasi)

v4:
* Rebase on refactoring of intel_dp_compute_config on tip (Manasi)
* Add a comment why we need to check PSR while enabling DSC (Gaurav)

v3:
* Check PPR > max_cdclock to use 2 VDSC instances (Ville)

v2:
* Add if-else for eDP/DP (Gaurav)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
---
 drivers/gpu/drm/i915/intel_display.c |   2 +-
 drivers/gpu/drm/i915/intel_display.h |   3 +-
 drivers/gpu/drm/i915/intel_dp.c      | 192 ++++++++++++++++++++++++---
 3 files changed, 172 insertions(+), 25 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index d07fa4456150..18ab713f9a6b 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -6736,7 +6736,7 @@ static void compute_m_n(unsigned int m, unsigned int n,
 }
 
 void
-intel_link_compute_m_n(int bits_per_pixel, int nlanes,
+intel_link_compute_m_n(u16 bits_per_pixel, int nlanes,
 		       int pixel_clock, int link_clock,
 		       struct intel_link_m_n *m_n,
 		       bool constant_n)
diff --git a/drivers/gpu/drm/i915/intel_display.h b/drivers/gpu/drm/i915/intel_display.h
index a7ceb8f904f7..3ec704c93d6e 100644
--- a/drivers/gpu/drm/i915/intel_display.h
+++ b/drivers/gpu/drm/i915/intel_display.h
@@ -440,10 +440,9 @@ struct intel_link_m_n {
 	     (__i)++) \
 		for_each_if(crtc)
 
-void intel_link_compute_m_n(int bpp, int nlanes,
+void intel_link_compute_m_n(u16 bpp, int nlanes,
 			    int pixel_clock, int link_clock,
 			    struct intel_link_m_n *m_n,
 			    bool constant_n);
-
 bool is_ccs_modifier(u64 modifier);
 #endif
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 70ae3d57316b..a2780733768a 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -47,6 +47,8 @@
 
 /* DP DSC small joiner has 2 FIFOs each of 640 x 6 bytes */
 #define DP_DSC_MAX_SMALL_JOINER_RAM_BUFFER	61440
+#define DP_DSC_MIN_SUPPORTED_BPC		8
+#define DP_DSC_MAX_SUPPORTED_BPC		10
 
 /* DP DSC throughput values used for slice count calculations KPixels/s */
 #define DP_DSC_PEAK_PIXEL_RATE			2720000
@@ -1708,6 +1710,26 @@ struct link_config_limits {
 	int min_bpp, max_bpp;
 };
 
+static bool intel_dp_source_supports_dsc(struct intel_dp *intel_dp,
+					 const struct intel_crtc_state *pipe_config)
+{
+	struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
+
+	/* FIXME: FEC needed for external DP until then reject DSC on DP */
+	if (!intel_dp_is_edp(intel_dp))
+		return false;
+
+	return INTEL_GEN(dev_priv) >= 10 &&
+		pipe_config->cpu_transcoder != TRANSCODER_A;
+}
+
+static bool intel_dp_supports_dsc(struct intel_dp *intel_dp,
+				  const struct intel_crtc_state *pipe_config)
+{
+	return intel_dp_source_supports_dsc(intel_dp, pipe_config) &&
+		drm_dp_sink_supports_dsc(intel_dp->dsc_dpcd);
+}
+
 static int intel_dp_compute_bpp(struct intel_dp *intel_dp,
 				struct intel_crtc_state *pipe_config)
 {
@@ -1842,14 +1864,115 @@ intel_dp_compute_link_config_fast(struct intel_dp *intel_dp,
 	return false;
 }
 
+static int intel_dp_dsc_compute_bpp(struct intel_dp *intel_dp, u8 dsc_max_bpc)
+{
+	int i, num_bpc;
+	u8 dsc_bpc[3] = {0};
+
+	num_bpc = drm_dp_dsc_sink_supported_input_bpcs(intel_dp->dsc_dpcd,
+						       dsc_bpc);
+	for (i = 0; i < num_bpc; i++) {
+		if (dsc_max_bpc >= dsc_bpc[i])
+			return dsc_bpc[i] * 3;
+	}
+
+	return 0;
+}
+
+static bool intel_dp_dsc_compute_config(struct intel_dp *intel_dp,
+					struct intel_crtc_state *pipe_config,
+					struct drm_connector_state *conn_state,
+					struct link_config_limits *limits)
+{
+	struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
+	struct drm_i915_private *dev_priv = to_i915(dig_port->base.base.dev);
+	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
+	u8 dsc_max_bpc;
+	int pipe_bpp;
+
+	if (!intel_dp_supports_dsc(intel_dp, pipe_config))
+		return false;
+
+	dsc_max_bpc = min_t(u8, DP_DSC_MAX_SUPPORTED_BPC,
+			    conn_state->max_requested_bpc);
+
+	pipe_bpp = intel_dp_dsc_compute_bpp(intel_dp, dsc_max_bpc);
+	if (pipe_bpp < DP_DSC_MIN_SUPPORTED_BPC * 3) {
+		DRM_DEBUG_KMS("No DSC support for less than 8bpc\n");
+		return false;
+	}
+
+	/*
+	 * For now enable DSC for max bpp, max link rate, max lane count.
+	 * Optimize this later for the minimum possible link rate/lane count
+	 * with DSC enabled for the requested mode.
+	 */
+	pipe_config->pipe_bpp = pipe_bpp;
+	pipe_config->port_clock = intel_dp->common_rates[limits->max_clock];
+	pipe_config->lane_count = limits->max_lane_count;
+
+	if (intel_dp_is_edp(intel_dp)) {
+		pipe_config->dsc_params.compressed_bpp =
+			min_t(u16, drm_edp_dsc_sink_output_bpp(intel_dp->dsc_dpcd) >> 4,
+			      pipe_config->pipe_bpp);
+		pipe_config->dsc_params.slice_count =
+			drm_dp_dsc_sink_max_slice_count(intel_dp->dsc_dpcd,
+							true);
+	} else {
+		u16 dsc_max_output_bpp;
+		u8 dsc_dp_slice_count;
+
+		dsc_max_output_bpp =
+			intel_dp_dsc_get_output_bpp(pipe_config->port_clock,
+						    pipe_config->lane_count,
+						    adjusted_mode->crtc_clock,
+						    adjusted_mode->crtc_hdisplay);
+		dsc_dp_slice_count =
+			intel_dp_dsc_get_slice_count(intel_dp,
+						     adjusted_mode->crtc_clock,
+						     adjusted_mode->crtc_hdisplay);
+		if (!dsc_max_output_bpp || !dsc_dp_slice_count) {
+			DRM_DEBUG_KMS("Compressed BPP/Slice Count not supported\n");
+			return false;
+		}
+		pipe_config->dsc_params.compressed_bpp = min_t(u16,
+							       dsc_max_output_bpp >> 4,
+							       pipe_config->pipe_bpp);
+		pipe_config->dsc_params.slice_count = dsc_dp_slice_count;
+	}
+	/*
+	 * VDSC engine operates at 1 Pixel per clock, so if peak pixel rate
+	 * is greater than the maximum Cdclock and if slice count is even
+	 * then we need to use 2 VDSC instances.
+	 */
+	if (adjusted_mode->crtc_clock > dev_priv->max_cdclk_freq) {
+		if (pipe_config->dsc_params.slice_count > 1) {
+			pipe_config->dsc_params.dsc_split = true;
+		} else {
+			DRM_DEBUG_KMS("Cannot split stream to use 2 VDSC instances\n");
+			return false;
+		}
+	}
+	pipe_config->dsc_params.compression_enable = true;
+	DRM_DEBUG_KMS("DP DSC computed with Input Bpp = %d "
+		      "Compressed Bpp = %d Slice Count = %d\n",
+		      pipe_config->pipe_bpp,
+		      pipe_config->dsc_params.compressed_bpp,
+		      pipe_config->dsc_params.slice_count);
+
+	return true;
+}
+
 static bool
 intel_dp_compute_link_config(struct intel_encoder *encoder,
-			     struct intel_crtc_state *pipe_config)
+			     struct intel_crtc_state *pipe_config,
+			     struct drm_connector_state *conn_state)
 {
 	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
 	struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
 	struct link_config_limits limits;
 	int common_len;
+	bool ret;
 
 	common_len = intel_dp_common_len_rate_limit(intel_dp,
 						    intel_dp->max_link_rate);
@@ -1888,7 +2011,7 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
 		      intel_dp->common_rates[limits.max_clock],
 		      limits.max_bpp, adjusted_mode->crtc_clock);
 
-	if (intel_dp_is_edp(intel_dp)) {
+	if (intel_dp_is_edp(intel_dp))
 		/*
 		 * Optimize for fast and narrow. eDP 1.3 section 3.3 and eDP 1.4
 		 * section A.1: "It is recommended that the minimum number of
@@ -1898,26 +2021,42 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
 		 * Note that we use the max clock and lane count for eDP 1.3 and
 		 * earlier, and fast vs. wide is irrelevant.
 		 */
-		if (!intel_dp_compute_link_config_fast(intel_dp, pipe_config,
-						       &limits))
-			return false;
-	} else {
+		ret = intel_dp_compute_link_config_fast(intel_dp, pipe_config,
+							&limits);
+	else
 		/* Optimize for slow and wide. */
-		if (!intel_dp_compute_link_config_wide(intel_dp, pipe_config,
-						       &limits))
+		ret = intel_dp_compute_link_config_wide(intel_dp, pipe_config,
+							&limits);
+
+	/* enable compression if the mode doesn't fit available BW */
+	if (!ret) {
+		if (!intel_dp_dsc_compute_config(intel_dp, pipe_config,
+						 conn_state, &limits))
 			return false;
 	}
 
-	DRM_DEBUG_KMS("DP lane count %d clock %d bpp %d\n",
-		      pipe_config->lane_count, pipe_config->port_clock,
-		      pipe_config->pipe_bpp);
+	if (pipe_config->dsc_params.compression_enable) {
+		DRM_DEBUG_KMS("DP lane count %d clock %d Input bpp %d Compressed bpp %d\n",
+			      pipe_config->lane_count, pipe_config->port_clock,
+			      pipe_config->pipe_bpp,
+			      pipe_config->dsc_params.compressed_bpp);
 
-	DRM_DEBUG_KMS("DP link rate required %i available %i\n",
-		      intel_dp_link_required(adjusted_mode->crtc_clock,
-					     pipe_config->pipe_bpp),
-		      intel_dp_max_data_rate(pipe_config->port_clock,
-					     pipe_config->lane_count));
+		DRM_DEBUG_KMS("DP link rate required %i available %i\n",
+			      intel_dp_link_required(adjusted_mode->crtc_clock,
+						     pipe_config->dsc_params.compressed_bpp),
+			      intel_dp_max_data_rate(pipe_config->port_clock,
+						     pipe_config->lane_count));
+	} else {
+		DRM_DEBUG_KMS("DP lane count %d clock %d bpp %d\n",
+			      pipe_config->lane_count, pipe_config->port_clock,
+			      pipe_config->pipe_bpp);
 
+		DRM_DEBUG_KMS("DP link rate required %i available %i\n",
+			      intel_dp_link_required(adjusted_mode->crtc_clock,
+						     pipe_config->pipe_bpp),
+			      intel_dp_max_data_rate(pipe_config->port_clock,
+						     pipe_config->lane_count));
+	}
 	return true;
 }
 
@@ -1983,7 +2122,7 @@ intel_dp_compute_config(struct intel_encoder *encoder,
 	if (adjusted_mode->flags & DRM_MODE_FLAG_DBLCLK)
 		return false;
 
-	if (!intel_dp_compute_link_config(encoder, pipe_config))
+	if (!intel_dp_compute_link_config(encoder, pipe_config, conn_state))
 		return false;
 
 	if (intel_conn_state->broadcast_rgb == INTEL_BROADCAST_RGB_AUTO) {
@@ -2001,11 +2140,20 @@ intel_dp_compute_config(struct intel_encoder *encoder,
 			intel_conn_state->broadcast_rgb == INTEL_BROADCAST_RGB_LIMITED;
 	}
 
-	intel_link_compute_m_n(pipe_config->pipe_bpp, pipe_config->lane_count,
-			       adjusted_mode->crtc_clock,
-			       pipe_config->port_clock,
-			       &pipe_config->dp_m_n,
-			       constant_n);
+	if (!pipe_config->dsc_params.compression_enable)
+		intel_link_compute_m_n(pipe_config->pipe_bpp,
+				       pipe_config->lane_count,
+				       adjusted_mode->crtc_clock,
+				       pipe_config->port_clock,
+				       &pipe_config->dp_m_n,
+				       constant_n);
+	else
+		intel_link_compute_m_n(pipe_config->dsc_params.compression_enable,
+				       pipe_config->lane_count,
+				       adjusted_mode->crtc_clock,
+				       pipe_config->port_clock,
+				       &pipe_config->dp_m_n,
+				       constant_n);
 
 	if (intel_connector->panel.downclock_mode != NULL &&
 		dev_priv->drrs.type == SEAMLESS_DRRS_SUPPORT) {
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

✗ Fi.CI.CHECKPATCH: warning for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev2)

[Patchwork]

== Series Details ==

Series: series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev2)
URL   : https://patchwork.freedesktop.org/series/53184/
State : warning

== Summary ==

$ dim checkpatch origin/drm-tip
6cc046b0e53f drm/i915/dp: Add DSC params and DSC config to intel_crtc_state
-:49: CHECK:BOOL_MEMBER: Avoid using bool structure members because of possible alignment issues - see: https://lkml.org/lkml/2017/11/21/384
#49: FILE: drivers/gpu/drm/i915/intel_drv.h:948:
+		bool compression_enable;

-:50: CHECK:BOOL_MEMBER: Avoid using bool structure members because of possible alignment issues - see: https://lkml.org/lkml/2017/11/21/384
#50: FILE: drivers/gpu/drm/i915/intel_drv.h:949:
+		bool dsc_split;

total: 0 errors, 0 warnings, 2 checks, 22 lines checked
3251c57ea8f7 drm/i915/dp: Compute DSC pipe config in atomic check
7e99dcca72b9 drm/i915/dp: Do not enable PSR2 if DSC is enabled
682f70ba2e90 drm/i915/dsc: Define & Compute VESA DSC params
-:68: WARNING:BAD_SIGN_OFF: Non-standard signature: Co-developed-by:
#68: 
Co-developed-by: Manasi Navare <manasi.d.navare@intel.com>

-:119: WARNING:FILE_PATH_CHANGES: added, moved or deleted file(s), does MAINTAINERS need updating?
#119: 
new file mode 100644

total: 0 errors, 2 warnings, 0 checks, 497 lines checked
f0efd1a5bded drm/i915/dsc: Compute Rate Control parameters for DSC
5a207b28b067 drm/i915/dp: Enable/Disable DSC in DP Sink
0541a790e095 drm/i915/dsc: Add a power domain for VDSC on eDP/MIPI DSI
f078f264482d drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling
-:391: WARNING:LONG_LINE: line over 100 characters
#391: FILE: drivers/gpu/drm/i915/intel_vdsc.c:897:
+		rc_range_params_dword[i / 2] |= (u32)(((vdsc_cfg->rc_range_params[i].range_bpg_offset <<

total: 0 errors, 1 warnings, 0 checks, 426 lines checked
909a40d71447 drm/i915/dp: Use the existing write_infoframe() for DSC PPS SDPs
ad3fbff47ade drm/i915/dp: Populate DSC PPS SDP and send PPS infoframes
ca153c0dbe0a drm/i915/dp: Configure Display stream splitter registers during DSC enable
1cfac339f7ea drm/i915/dp: Disable DSC in source by disabling DSS CTL bits
2f4fb87c9b59 drm/i915/dsc: Enable and disable appropriate power wells for VDSC
9211bdb6b64b i915/dp/fec: Add fec_enable to the crtc state.
-:126: CHECK:BOOL_MEMBER: Avoid using bool structure members because of possible alignment issues - see: https://lkml.org/lkml/2017/11/21/384
#126: FILE: drivers/gpu/drm/i915/intel_drv.h:956:
+	bool fec_enable;

total: 0 errors, 0 warnings, 1 checks, 65 lines checked
2cb9fde528c3 drm/i915/fec: Set FEC_READY in FEC_CONFIGURATION
303f000edcd4 i915/dp/fec: Configure the Forward Error Correction bits.
c878df13f9c0 drm/i915/fec: Disable FEC state.

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

✗ Fi.CI.SPARSE: warning for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev2)

[Patchwork]

== Series Details ==

Series: series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev2)
URL   : https://patchwork.freedesktop.org/series/53184/
State : warning

== Summary ==

$ dim sparse origin/drm-tip
Sparse version: v0.5.2
Commit: drm/i915/dp: Add DSC params and DSC config to intel_crtc_state
-drivers/gpu/drm/i915/selftests/../i915_drv.h:3566:16: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/selftests/../i915_drv.h:3567:16: warning: expression using sizeof(void)

Commit: drm/i915/dp: Compute DSC pipe config in atomic check
+drivers/gpu/drm/i915/intel_dp.c:1896:23: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/intel_dp.c:1916:25: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/intel_dp.c:1916:25: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/intel_dp.c:1938:58: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/intel_dp.c:1938:58: warning: expression using sizeof(void)

Commit: drm/i915/dp: Do not enable PSR2 if DSC is enabled
Okay!

Commit: drm/i915/dsc: Define & Compute VESA DSC params
+drivers/gpu/drm/i915/intel_vdsc.c:352:17: warning: expression using sizeof(void)
+./include/uapi/linux/perf_event.h:147:56: warning: cast truncates bits from constant value (8000000000000000 becomes 0)

Commit: drm/i915/dsc: Compute Rate Control parameters for DSC
Okay!

Commit: drm/i915/dp: Enable/Disable DSC in DP Sink
Okay!

Commit: drm/i915/dsc: Add a power domain for VDSC on eDP/MIPI DSI
Okay!

Commit: drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling
-drivers/gpu/drm/i915/selftests/../i915_drv.h:3567:16: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/selftests/../i915_drv.h:3569:16: warning: expression using sizeof(void)

Commit: drm/i915/dp: Use the existing write_infoframe() for DSC PPS SDPs
Okay!

Commit: drm/i915/dp: Populate DSC PPS SDP and send PPS infoframes
Okay!

Commit: drm/i915/dp: Configure Display stream splitter registers during DSC enable
Okay!

Commit: drm/i915/dp: Disable DSC in source by disabling DSS CTL bits
-drivers/gpu/drm/i915/selftests/../i915_drv.h:3569:16: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/selftests/../i915_drv.h:3570:16: warning: expression using sizeof(void)

Commit: drm/i915/dsc: Enable and disable appropriate power wells for VDSC
Okay!

Commit: i915/dp/fec: Add fec_enable to the crtc state.
Okay!

Commit: drm/i915/fec: Set FEC_READY in FEC_CONFIGURATION
Okay!

Commit: i915/dp/fec: Configure the Forward Error Correction bits.
Okay!

Commit: drm/i915/fec: Disable FEC state.
Okay!

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

✓ Fi.CI.BAT: success for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev2)

[Patchwork]

== Series Details ==

Series: series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev2)
URL   : https://patchwork.freedesktop.org/series/53184/
State : success

== Summary ==

CI Bug Log - changes from CI_DRM_5217 -> Patchwork_10939
====================================================

Summary
-------

  **SUCCESS**

  No regressions found.

  External URL: https://patchwork.freedesktop.org/api/1.0/series/53184/revisions/2/mbox/

Known issues
------------

  Here are the changes found in Patchwork_10939 that come from known issues:

### IGT changes ###

#### Issues hit ####

  * igt@i915_selftest@live_contexts:
    - fi-bsw-kefka:       PASS -> DMESG-FAIL [fdo#108626] / [fdo#108656]

  * igt@kms_frontbuffer_tracking@basic:
    - fi-byt-clapper:     PASS -> FAIL [fdo#103167]

  * igt@kms_pipe_crc_basic@nonblocking-crc-pipe-a-frame-sequence:
    - fi-byt-clapper:     PASS -> FAIL [fdo#103191] / [fdo#107362]

  
  [fdo#103167]: https://bugs.freedesktop.org/show_bug.cgi?id=103167
  [fdo#103191]: https://bugs.freedesktop.org/show_bug.cgi?id=103191
  [fdo#107362]: https://bugs.freedesktop.org/show_bug.cgi?id=107362
  [fdo#108626]: https://bugs.freedesktop.org/show_bug.cgi?id=108626
  [fdo#108656]: https://bugs.freedesktop.org/show_bug.cgi?id=108656


Participating hosts (49 -> 42)
------------------------------

  Missing    (7): fi-kbl-soraka fi-ilk-m540 fi-hsw-4200u fi-byt-j1900 fi-byt-squawks fi-bsw-cyan fi-ctg-p8600 


Build changes
-------------

    * Linux: CI_DRM_5217 -> Patchwork_10939

  CI_DRM_5217: 3b8acd938b1edc326fb69d377cbceca8791df177 @ git://anongit.freedesktop.org/gfx-ci/linux
  IGT_4735: b05c028ccdb6ac8e8d8499a041bb14dfe358ee26 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
  Patchwork_10939: c878df13f9c00451f7281d105e0f2246cd65748c @ git://anongit.freedesktop.org/gfx-ci/linux


== Linux commits ==

c878df13f9c0 drm/i915/fec: Disable FEC state.
303f000edcd4 i915/dp/fec: Configure the Forward Error Correction bits.
2cb9fde528c3 drm/i915/fec: Set FEC_READY in FEC_CONFIGURATION
9211bdb6b64b i915/dp/fec: Add fec_enable to the crtc state.
2f4fb87c9b59 drm/i915/dsc: Enable and disable appropriate power wells for VDSC
1cfac339f7ea drm/i915/dp: Disable DSC in source by disabling DSS CTL bits
ca153c0dbe0a drm/i915/dp: Configure Display stream splitter registers during DSC enable
ad3fbff47ade drm/i915/dp: Populate DSC PPS SDP and send PPS infoframes
909a40d71447 drm/i915/dp: Use the existing write_infoframe() for DSC PPS SDPs
f078f264482d drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling
0541a790e095 drm/i915/dsc: Add a power domain for VDSC on eDP/MIPI DSI
5a207b28b067 drm/i915/dp: Enable/Disable DSC in DP Sink
f0efd1a5bded drm/i915/dsc: Compute Rate Control parameters for DSC
682f70ba2e90 drm/i915/dsc: Define & Compute VESA DSC params
7e99dcca72b9 drm/i915/dp: Do not enable PSR2 if DSC is enabled
3251c57ea8f7 drm/i915/dp: Compute DSC pipe config in atomic check
6cc046b0e53f drm/i915/dp: Add DSC params and DSC config to intel_crtc_state

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10939/
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

✓ Fi.CI.IGT: success for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev2)

[Patchwork]

== Series Details ==

Series: series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev2)
URL   : https://patchwork.freedesktop.org/series/53184/
State : success

== Summary ==

CI Bug Log - changes from CI_DRM_5217_full -> Patchwork_10939_full
====================================================

Summary
-------

  **WARNING**

  Minor unknown changes coming with Patchwork_10939_full need to be verified
  manually.
  
  If you think the reported changes have nothing to do with the changes
  introduced in Patchwork_10939_full, please notify your bug team to allow them
  to document this new failure mode, which will reduce false positives in CI.

  

Possible new issues
-------------------

  Here are the unknown changes that may have been introduced in Patchwork_10939_full:

### IGT changes ###

#### Warnings ####

  * igt@kms_vblank@pipe-a-ts-continuation-modeset:
    - shard-snb:          PASS -> SKIP

  * igt@kms_vblank@pipe-a-ts-continuation-modeset-hang:
    - shard-snb:          SKIP -> PASS

  * igt@perf_pmu@rc6:
    - shard-kbl:          SKIP -> PASS

  
Known issues
------------

  Here are the changes found in Patchwork_10939_full that come from known issues:

### IGT changes ###

#### Issues hit ####

  * igt@gem_eio@in-flight-10ms:
    - {shard-iclb}:       PASS -> INCOMPLETE [fdo#108343]

  * igt@gem_workarounds@suspend-resume-fd:
    - shard-skl:          PASS -> INCOMPLETE [fdo#104108] / [fdo#107773]

  * igt@kms_busy@extended-modeset-hang-newfb-render-b:
    - shard-skl:          NOTRUN -> DMESG-WARN [fdo#107956]

  * igt@kms_busy@extended-modeset-hang-newfb-with-reset-render-a:
    - shard-skl:          PASS -> DMESG-WARN [fdo#107956]

  * igt@kms_ccs@pipe-c-crc-primary-rotation-180:
    - {shard-iclb}:       NOTRUN -> FAIL [fdo#107725]

  * igt@kms_chv_cursor_fail@pipe-a-128x128-bottom-edge:
    - {shard-iclb}:       PASS -> DMESG-WARN [fdo#107724] / [fdo#108336] +1

  * igt@kms_color@pipe-a-degamma:
    - shard-apl:          PASS -> FAIL [fdo#104782] / [fdo#108145]

  * igt@kms_cursor_crc@cursor-128x128-suspend:
    - shard-apl:          PASS -> FAIL [fdo#103191] / [fdo#103232]

  * igt@kms_cursor_crc@cursor-256x256-dpms:
    - shard-skl:          NOTRUN -> FAIL [fdo#103232]

  * igt@kms_cursor_crc@cursor-64x21-random:
    - {shard-iclb}:       NOTRUN -> FAIL [fdo#103232]

  * igt@kms_cursor_crc@cursor-64x64-onscreen:
    - shard-snb:          NOTRUN -> INCOMPLETE [fdo#105411]

  * igt@kms_cursor_legacy@pipe-c-torture-move:
    - shard-apl:          PASS -> INCOMPLETE [fdo#103927]

  * igt@kms_draw_crc@draw-method-xrgb8888-mmap-cpu-xtiled:
    - {shard-iclb}:       PASS -> WARN [fdo#108336]

  * igt@kms_frontbuffer_tracking@fbc-suspend:
    - shard-skl:          PASS -> INCOMPLETE [fdo#104108] / [fdo#105959] / [fdo#107773]

  * igt@kms_frontbuffer_tracking@fbcpsr-stridechange:
    - shard-skl:          NOTRUN -> FAIL [fdo#105683]

  * igt@kms_frontbuffer_tracking@psr-1p-primscrn-spr-indfb-draw-render:
    - shard-skl:          NOTRUN -> FAIL [fdo#103167]

  * igt@kms_frontbuffer_tracking@psr-1p-primscrn-spr-indfb-fullscreen:
    - {shard-iclb}:       PASS -> FAIL [fdo#103167] +7

  * igt@kms_plane@plane-panning-bottom-right-suspend-pipe-b-planes:
    - {shard-iclb}:       PASS -> DMESG-FAIL [fdo#103166] / [fdo#107724]
    - shard-skl:          PASS -> INCOMPLETE [fdo#104108]

  * igt@kms_plane@plane-position-covered-pipe-a-planes:
    - {shard-iclb}:       PASS -> FAIL [fdo#103166] +2

  * igt@kms_plane_alpha_blend@pipe-a-alpha-opaque-fb:
    - shard-apl:          PASS -> FAIL [fdo#108145]

  * igt@kms_plane_alpha_blend@pipe-b-constant-alpha-max:
    - shard-glk:          PASS -> FAIL [fdo#108145]

  * igt@kms_plane_alpha_blend@pipe-c-alpha-transparant-fb:
    - shard-skl:          NOTRUN -> FAIL [fdo#108145] +2

  * igt@kms_plane_multiple@atomic-pipe-c-tiling-y:
    - shard-glk:          PASS -> FAIL [fdo#103166] +1

  * igt@kms_plane_scaling@pipe-b-scaler-with-pixel-format:
    - {shard-iclb}:       PASS -> DMESG-WARN [fdo#107724] +7

  * igt@kms_plane_scaling@pipe-b-scaler-with-rotation:
    - {shard-iclb}:       NOTRUN -> DMESG-WARN [fdo#107724] +1

  * igt@kms_setmode@basic:
    - shard-hsw:          PASS -> FAIL [fdo#99912]

  * igt@pm_rpm@gem-execbuf:
    - shard-skl:          PASS -> INCOMPLETE [fdo#107803] / [fdo#107807]

  * igt@pm_rpm@modeset-stress-extra-wait:
    - shard-skl:          PASS -> INCOMPLETE [fdo#107807] +1

  * igt@pm_rps@waitboost:
    - {shard-iclb}:       NOTRUN -> FAIL [fdo#102250] / [fdo#108059]

  
#### Possible fixes ####

  * igt@drm_import_export@import-close-race-flink:
    - shard-skl:          TIMEOUT [fdo#108667] -> PASS

  * igt@gem_ctx_isolation@vecs0-s3:
    - shard-kbl:          INCOMPLETE [fdo#103665] -> PASS

  * igt@gem_softpin@noreloc-s3:
    - shard-skl:          INCOMPLETE [fdo#104108] / [fdo#107773] -> PASS

  * igt@kms_ccs@pipe-a-crc-primary-basic:
    - shard-skl:          FAIL [fdo#107725] -> PASS

  * igt@kms_color@pipe-a-gamma:
    - shard-skl:          FAIL [fdo#104782] -> PASS

  * igt@kms_cursor_crc@cursor-256x85-onscreen:
    - shard-apl:          FAIL [fdo#103232] -> PASS +3

  * igt@kms_draw_crc@draw-method-rgb565-mmap-wc-xtiled:
    - {shard-iclb}:       WARN [fdo#108336] -> PASS

  * igt@kms_flip@plain-flip-fb-recreate:
    - shard-skl:          FAIL [fdo#100368] -> PASS

  * igt@kms_flip_tiling@flip-to-y-tiled:
    - shard-skl:          FAIL [fdo#107931] -> PASS

  * igt@kms_frontbuffer_tracking@fbc-1p-primscrn-cur-indfb-draw-pwrite:
    - {shard-iclb}:       FAIL [fdo#103167] -> PASS

  * igt@kms_frontbuffer_tracking@fbc-1p-primscrn-cur-indfb-move:
    - {shard-iclb}:       DMESG-FAIL [fdo#107724] -> PASS +4

  * igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-draw-mmap-wc:
    - shard-glk:          FAIL [fdo#103167] -> PASS +1

  * igt@kms_frontbuffer_tracking@fbc-1p-rte:
    - shard-apl:          FAIL [fdo#103167] / [fdo#105682] -> PASS

  * igt@kms_frontbuffer_tracking@fbc-shrfb-scaledprimary:
    - shard-skl:          FAIL [fdo#103167] -> PASS +3

  * igt@kms_frontbuffer_tracking@psr-1p-primscrn-pri-shrfb-draw-mmap-gtt:
    - {shard-iclb}:       DMESG-WARN [fdo#107724] / [fdo#108336] -> PASS +6

  * igt@kms_pipe_crc_basic@read-crc-pipe-a:
    - shard-apl:          DMESG-WARN [fdo#103558] / [fdo#105602] -> PASS +17

  * igt@kms_plane@plane-position-covered-pipe-c-planes:
    - shard-apl:          FAIL [fdo#103166] -> PASS +1
    - shard-glk:          FAIL [fdo#103166] -> PASS +1
    - {shard-iclb}:       FAIL [fdo#103166] -> PASS

  * igt@kms_psr@no_drrs:
    - {shard-iclb}:       FAIL [fdo#108341] -> PASS

  * igt@pm_rpm@cursor:
    - shard-skl:          INCOMPLETE [fdo#107807] -> PASS

  * igt@pm_rpm@debugfs-read:
    - {shard-iclb}:       DMESG-WARN [fdo#107724] -> PASS +9

  * igt@pm_rpm@i2c:
    - {shard-iclb}:       FAIL [fdo#104097] -> PASS

  * igt@pm_rpm@modeset-pc8-residency-stress:
    - shard-skl:          INCOMPLETE [fdo#107807] -> SKIP +1

  * igt@pm_rpm@universal-planes:
    - {shard-iclb}:       DMESG-WARN [fdo#108654] / [fdo#108756] -> PASS

  * igt@syncobj_wait@multi-wait-for-submit-unsubmitted-signaled:
    - shard-snb:          INCOMPLETE [fdo#105411] / [fdo#107469] -> PASS

  
#### Warnings ####

  * igt@kms_cursor_crc@cursor-128x42-random:
    - {shard-iclb}:       DMESG-WARN [fdo#107724] / [fdo#108336] -> FAIL [fdo#103232]

  * igt@kms_cursor_crc@cursor-64x64-suspend:
    - {shard-iclb}:       FAIL [fdo#103232] -> DMESG-FAIL [fdo#103232] / [fdo#107724]

  * igt@kms_plane@pixel-format-pipe-a-planes:
    - {shard-iclb}:       DMESG-WARN [fdo#107724] / [fdo#108336] -> FAIL [fdo#103166]

  
  {name}: This element is suppressed. This means it is ignored when computing
          the status of the difference (SUCCESS, WARNING, or FAILURE).

  [fdo#100368]: https://bugs.freedesktop.org/show_bug.cgi?id=100368
  [fdo#102250]: https://bugs.freedesktop.org/show_bug.cgi?id=102250
  [fdo#103166]: https://bugs.freedesktop.org/show_bug.cgi?id=103166
  [fdo#103167]: https://bugs.freedesktop.org/show_bug.cgi?id=103167
  [fdo#103191]: https://bugs.freedesktop.org/show_bug.cgi?id=103191
  [fdo#103232]: https://bugs.freedesktop.org/show_bug.cgi?id=103232
  [fdo#103558]: https://bugs.freedesktop.org/show_bug.cgi?id=103558
  [fdo#103665]: https://bugs.freedesktop.org/show_bug.cgi?id=103665
  [fdo#103927]: https://bugs.freedesktop.org/show_bug.cgi?id=103927
  [fdo#104097]: https://bugs.freedesktop.org/show_bug.cgi?id=104097
  [fdo#104108]: https://bugs.freedesktop.org/show_bug.cgi?id=104108
  [fdo#104782]: https://bugs.freedesktop.org/show_bug.cgi?id=104782
  [fdo#105411]: https://bugs.freedesktop.org/show_bug.cgi?id=105411
  [fdo#105602]: https://bugs.freedesktop.org/show_bug.cgi?id=105602
  [fdo#105682]: https://bugs.freedesktop.org/show_bug.cgi?id=105682
  [fdo#105683]: https://bugs.freedesktop.org/show_bug.cgi?id=105683
  [fdo#105959]: https://bugs.freedesktop.org/show_bug.cgi?id=105959
  [fdo#107469]: https://bugs.freedesktop.org/show_bug.cgi?id=107469
  [fdo#107724]: https://bugs.freedesktop.org/show_bug.cgi?id=107724
  [fdo#107725]: https://bugs.freedesktop.org/show_bug.cgi?id=107725
  [fdo#107773]: https://bugs.freedesktop.org/show_bug.cgi?id=107773
  [fdo#107803]: https://bugs.freedesktop.org/show_bug.cgi?id=107803
  [fdo#107807]: https://bugs.freedesktop.org/show_bug.cgi?id=107807
  [fdo#107931]: https://bugs.freedesktop.org/show_bug.cgi?id=107931
  [fdo#107956]: https://bugs.freedesktop.org/show_bug.cgi?id=107956
  [fdo#108059]: https://bugs.freedesktop.org/show_bug.cgi?id=108059
  [fdo#108145]: https://bugs.freedesktop.org/show_bug.cgi?id=108145
  [fdo#108336]: https://bugs.freedesktop.org/show_bug.cgi?id=108336
  [fdo#108341]: https://bugs.freedesktop.org/show_bug.cgi?id=108341
  [fdo#108343]: https://bugs.freedesktop.org/show_bug.cgi?id=108343
  [fdo#108654]: https://bugs.freedesktop.org/show_bug.cgi?id=108654
  [fdo#108667]: https://bugs.freedesktop.org/show_bug.cgi?id=108667
  [fdo#108756]: https://bugs.freedesktop.org/show_bug.cgi?id=108756
  [fdo#99912]: https://bugs.freedesktop.org/show_bug.cgi?id=99912


Participating hosts (7 -> 7)
------------------------------

  No changes in participating hosts


Build changes
-------------

    * Linux: CI_DRM_5217 -> Patchwork_10939

  CI_DRM_5217: 3b8acd938b1edc326fb69d377cbceca8791df177 @ git://anongit.freedesktop.org/gfx-ci/linux
  IGT_4735: b05c028ccdb6ac8e8d8499a041bb14dfe358ee26 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
  Patchwork_10939: c878df13f9c00451f7281d105e0f2246cd65748c @ git://anongit.freedesktop.org/gfx-ci/linux
  piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10939/shards.html
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

[CI v15 04/17] drm/i915/dsc: Define & Compute VESA DSC params

[Manasi Navare]

From: Gaurav K Singh <gaurav.k.singh@intel.com>

This patches does the following:

1. This patch defines all the DSC parameters as per the VESA
DSC specification. These are stored in the encoder and used
to compute the PPS parameters to be sent to the Sink.
2. Compute all the DSC parameters which are derived from DSC
state of intel_crtc_state.
3. Compute all parameters that are VESA DSC specific

This computation happens in the atomic check phase during
compute_config() to validate if display stream compression
can be enabled for the requested mode.

v8 (From Manasi):
* DEBUG_KMS instead of DRM_ERROR for user triggerable
errors (Ville)
v7: (From Manasi)
* Dont use signed int for rc_range_params (Manasi)
* Mask the range_bpg_offset to use only 6 bits
* Add SPDX identifier (Chris Wilson)
v6 (From Manasi):
* Add a check for line_buf_depth return value (Anusha)
* Remove DRM DSC constants to different patch (Manasi)
v5 (From Manasi):
* Add logic to limit the max line buf depth for DSC 1.1 to 13
as per DSC 1.1 spec
* Fix dim checkpatch warnings/checks

v4 (From Gaurav):
* Rebase on latest drm tip
* rename variable name(Manasi)
* Populate linebuf_depth variable(Manasi)

v3 (From Gaurav):
* Rebase my previous patches on top of Manasi's latest patch
series
* Using >>n rather than /2^n (Manasi)
* Change the commit message to explain what the patch is doing(Gaurav)

Fixed review comments from Ville:
* Don't use macro TWOS_COMPLEMENT
* Mention in comment about the source of RC params
* Return directly from case statements
* Using single asssignment for assigning rc_range_params
* Using <<n rather than *2^n and removing the comments
about the fixed point numbers

v2 (From Manasi):
* Update logic for minor version to consider the dpcd value
and what supported by the HW platform
* Use DRM DSC config struct instead of intel_dp struct
* Move the DSC constants to DRM DSC header file
* Use u16, u8 where bigger data types not needed
* * Compute the DSC parameters as part of DSC compute config
since the computation can fail (Manasi)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Co-developed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
---
 drivers/gpu/drm/i915/Makefile     |   3 +-
 drivers/gpu/drm/i915/intel_dp.c   |   7 +
 drivers/gpu/drm/i915/intel_drv.h  |   4 +
 drivers/gpu/drm/i915/intel_vdsc.c | 456 ++++++++++++++++++++++++++++++
 4 files changed, 469 insertions(+), 1 deletion(-)
 create mode 100644 drivers/gpu/drm/i915/intel_vdsc.c

diff --git a/drivers/gpu/drm/i915/Makefile b/drivers/gpu/drm/i915/Makefile
index 0ff878c994e2..8370b9de6e4f 100644
--- a/drivers/gpu/drm/i915/Makefile
+++ b/drivers/gpu/drm/i915/Makefile
@@ -157,7 +157,8 @@ i915-y += dvo_ch7017.o \
 	  intel_sdvo.o \
 	  intel_tv.o \
 	  vlv_dsi.o \
-	  vlv_dsi_pll.o
+	  vlv_dsi_pll.o \
+	  intel_vdsc.o
 
 # Post-mortem debug and GPU hang state capture
 i915-$(CONFIG_DRM_I915_CAPTURE_ERROR) += i915_gpu_error.o
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index a2780733768a..3b612eb134e7 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -1953,6 +1953,13 @@ static bool intel_dp_dsc_compute_config(struct intel_dp *intel_dp,
 			return false;
 		}
 	}
+	if (intel_dp_compute_dsc_params(intel_dp, pipe_config) < 0) {
+		DRM_DEBUG_KMS("Cannot compute valid DSC parameters for Input Bpp = %d "
+			      "Compressed BPP = %d\n",
+			      pipe_config->pipe_bpp,
+			      pipe_config->dsc_params.compressed_bpp);
+		return false;
+	}
 	pipe_config->dsc_params.compression_enable = true;
 	DRM_DEBUG_KMS("DP DSC computed with Input Bpp = %d "
 		      "Compressed Bpp = %d Slice Count = %d\n",
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index 5577f0f31b99..44a5b21799f5 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -1857,6 +1857,10 @@ uint16_t intel_dp_dsc_get_output_bpp(int link_clock, uint8_t lane_count,
 uint8_t intel_dp_dsc_get_slice_count(struct intel_dp *intel_dp, int mode_clock,
 				     int mode_hdisplay);
 
+/* intel_vdsc.c */
+int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
+				struct intel_crtc_state *pipe_config);
+
 static inline unsigned int intel_dp_unused_lane_mask(int lane_count)
 {
 	return ~((1 << lane_count) - 1) & 0xf;
diff --git a/drivers/gpu/drm/i915/intel_vdsc.c b/drivers/gpu/drm/i915/intel_vdsc.c
new file mode 100644
index 000000000000..5e0f9ac5667b
--- /dev/null
+++ b/drivers/gpu/drm/i915/intel_vdsc.c
@@ -0,0 +1,456 @@
+// SPDX-License-Identifier: MIT
+/*
+ * Copyright © 2018 Intel Corporation
+ *
+ * Author: Gaurav K Singh <gaurav.k.singh@intel.com>
+ *         Manasi Navare <manasi.d.navare@intel.com>
+ */
+
+#include <drm/drmP.h>
+#include <drm/i915_drm.h>
+#include "i915_drv.h"
+#include "intel_drv.h"
+
+enum ROW_INDEX_BPP {
+	ROW_INDEX_6BPP = 0,
+	ROW_INDEX_8BPP,
+	ROW_INDEX_10BPP,
+	ROW_INDEX_12BPP,
+	ROW_INDEX_15BPP,
+	MAX_ROW_INDEX
+};
+
+enum COLUMN_INDEX_BPC {
+	COLUMN_INDEX_8BPC = 0,
+	COLUMN_INDEX_10BPC,
+	COLUMN_INDEX_12BPC,
+	COLUMN_INDEX_14BPC,
+	COLUMN_INDEX_16BPC,
+	MAX_COLUMN_INDEX
+};
+
+#define DSC_SUPPORTED_VERSION_MIN		1
+
+/* From DSC_v1.11 spec, rc_parameter_Set syntax element typically constant */
+static u16 rc_buf_thresh[] = {
+	896, 1792, 2688, 3584, 4480, 5376, 6272, 6720, 7168, 7616,
+	7744, 7872, 8000, 8064
+};
+
+struct rc_parameters {
+	u16 initial_xmit_delay;
+	u8 first_line_bpg_offset;
+	u16 initial_offset;
+	u8 flatness_min_qp;
+	u8 flatness_max_qp;
+	u8 rc_quant_incr_limit0;
+	u8 rc_quant_incr_limit1;
+	struct drm_dsc_rc_range_parameters rc_range_params[DSC_NUM_BUF_RANGES];
+};
+
+/*
+ * Selected Rate Control Related Parameter Recommended Values
+ * from DSC_v1.11 spec & C Model release: DSC_model_20161212
+ */
+static struct rc_parameters rc_params[][MAX_COLUMN_INDEX] = {
+{
+	/* 6BPP/8BPC */
+	{ 768, 15, 6144, 3, 13, 11, 11, {
+		{ 0, 4, 0 }, { 1, 6, -2 }, { 3, 8, -2 }, { 4, 8, -4 },
+		{ 5, 9, -6 }, { 5, 9, -6 }, { 6, 9, -6 }, { 6, 10, -8 },
+		{ 7, 11, -8 }, { 8, 12, -10 }, { 9, 12, -10 }, { 10, 12, -12 },
+		{ 10, 12, -12 }, { 11, 12, -12 }, { 13, 14, -12 }
+		}
+	},
+	/* 6BPP/10BPC */
+	{ 768, 15, 6144, 7, 17, 15, 15, {
+		{ 0, 8, 0 }, { 3, 10, -2 }, { 7, 12, -2 }, { 8, 12, -4 },
+		{ 9, 13, -6 }, { 9, 13, -6 }, { 10, 13, -6 }, { 10, 14, -8 },
+		{ 11, 15, -8 }, { 12, 16, -10 }, { 13, 16, -10 },
+		{ 14, 16, -12 }, { 14, 16, -12 }, { 15, 16, -12 },
+		{ 17, 18, -12 }
+		}
+	},
+	/* 6BPP/12BPC */
+	{ 768, 15, 6144, 11, 21, 19, 19, {
+		{ 0, 12, 0 }, { 5, 14, -2 }, { 11, 16, -2 }, { 12, 16, -4 },
+		{ 13, 17, -6 }, { 13, 17, -6 }, { 14, 17, -6 }, { 14, 18, -8 },
+		{ 15, 19, -8 }, { 16, 20, -10 }, { 17, 20, -10 },
+		{ 18, 20, -12 }, { 18, 20, -12 }, { 19, 20, -12 },
+		{ 21, 22, -12 }
+		}
+	},
+	/* 6BPP/14BPC */
+	{ 768, 15, 6144, 15, 25, 23, 27, {
+		{ 0, 16, 0 }, { 7, 18, -2 }, { 15, 20, -2 }, { 16, 20, -4 },
+		{ 17, 21, -6 }, { 17, 21, -6 }, { 18, 21, -6 }, { 18, 22, -8 },
+		{ 19, 23, -8 }, { 20, 24, -10 }, { 21, 24, -10 },
+		{ 22, 24, -12 }, { 22, 24, -12 }, { 23, 24, -12 },
+		{ 25, 26, -12 }
+		}
+	},
+	/* 6BPP/16BPC */
+	{ 768, 15, 6144, 19, 29, 27, 27, {
+		{ 0, 20, 0 }, { 9, 22, -2 }, { 19, 24, -2 }, { 20, 24, -4 },
+		{ 21, 25, -6 }, { 21, 25, -6 }, { 22, 25, -6 }, { 22, 26, -8 },
+		{ 23, 27, -8 }, { 24, 28, -10 }, { 25, 28, -10 },
+		{ 26, 28, -12 }, { 26, 28, -12 }, { 27, 28, -12 },
+		{ 29, 30, -12 }
+		}
+	},
+},
+{
+	/* 8BPP/8BPC */
+	{ 512, 12, 6144, 3, 12, 11, 11, {
+		{ 0, 4, 2 }, { 0, 4, 0 }, { 1, 5, 0 }, { 1, 6, -2 },
+		{ 3, 7, -4 }, { 3, 7, -6 }, { 3, 7, -8 }, { 3, 8, -8 },
+		{ 3, 9, -8 }, { 3, 10, -10 }, { 5, 11, -10 }, { 5, 12, -12 },
+		{ 5, 13, -12 }, { 7, 13, -12 }, { 13, 15, -12 }
+		}
+	},
+	/* 8BPP/10BPC */
+	{ 512, 12, 6144, 7, 16, 15, 15, {
+		{ 0, 4, 2 }, { 4, 8, 0 }, { 5, 9, 0 }, { 5, 10, -2 },
+		{ 7, 11, -4 }, { 7, 11, -6 }, { 7, 11, -8 }, { 7, 12, -8 },
+		{ 7, 13, -8 }, { 7, 14, -10 }, { 9, 15, -10 }, { 9, 16, -12 },
+		{ 9, 17, -12 }, { 11, 17, -12 }, { 17, 19, -12 }
+		}
+	},
+	/* 8BPP/12BPC */
+	{ 512, 12, 6144, 11, 20, 19, 19, {
+		{ 0, 12, 2 }, { 4, 12, 0 }, { 9, 13, 0 }, { 9, 14, -2 },
+		{ 11, 15, -4 }, { 11, 15, -6 }, { 11, 15, -8 }, { 11, 16, -8 },
+		{ 11, 17, -8 }, { 11, 18, -10 }, { 13, 19, -10 },
+		{ 13, 20, -12 }, { 13, 21, -12 }, { 15, 21, -12 },
+		{ 21, 23, -12 }
+		}
+	},
+	/* 8BPP/14BPC */
+	{ 512, 12, 6144, 15, 24, 23, 23, {
+		{ 0, 12, 0 }, { 5, 13, 0 }, { 11, 15, 0 }, { 12, 17, -2 },
+		{ 15, 19, -4 }, { 15, 19, -6 }, { 15, 19, -8 }, { 15, 20, -8 },
+		{ 15, 21, -8 }, { 15, 22, -10 }, { 17, 22, -10 },
+		{ 17, 23, -12 }, { 17, 23, -12 }, { 21, 24, -12 },
+		{ 24, 25, -12 }
+		}
+	},
+	/* 8BPP/16BPC */
+	{ 512, 12, 6144, 19, 28, 27, 27, {
+		{ 0, 12, 2 }, { 6, 14, 0 }, { 13, 17, 0 }, { 15, 20, -2 },
+		{ 19, 23, -4 }, { 19, 23, -6 }, { 19, 23, -8 }, { 19, 24, -8 },
+		{ 19, 25, -8 }, { 19, 26, -10 }, { 21, 26, -10 },
+		{ 21, 27, -12 }, { 21, 27, -12 }, { 25, 28, -12 },
+		{ 28, 29, -12 }
+		}
+	},
+},
+{
+	/* 10BPP/8BPC */
+	{ 410, 15, 5632, 3, 12, 11, 11, {
+		{ 0, 3, 2 }, { 0, 4, 0 }, { 1, 5, 0 }, { 2, 6, -2 },
+		{ 3, 7, -4 }, { 3, 7, -6 }, { 3, 7, -8 }, { 3, 8, -8 },
+		{ 3, 9, -8 }, { 3, 9, -10 }, { 5, 10, -10 }, { 5, 10, -10 },
+		{ 5, 11, -12 }, { 7, 11, -12 }, { 11, 12, -12 }
+		}
+	},
+	/* 10BPP/10BPC */
+	{ 410, 15, 5632, 7, 16, 15, 15, {
+		{ 0, 7, 2 }, { 4, 8, 0 }, { 5, 9, 0 }, { 6, 10, -2 },
+		{ 7, 11, -4 }, { 7, 11, -6 }, { 7, 11, -8 }, { 7, 12, -8 },
+		{ 7, 13, -8 }, { 7, 13, -10 }, { 9, 14, -10 }, { 9, 14, -10 },
+		{ 9, 15, -12 }, { 11, 15, -12 }, { 15, 16, -12 }
+		}
+	},
+	/* 10BPP/12BPC */
+	{ 410, 15, 5632, 11, 20, 19, 19, {
+		{ 0, 11, 2 }, { 4, 12, 0 }, { 9, 13, 0 }, { 10, 14, -2 },
+		{ 11, 15, -4 }, { 11, 15, -6 }, { 11, 15, -8 }, { 11, 16, -8 },
+		{ 11, 17, -8 }, { 11, 17, -10 }, { 13, 18, -10 },
+		{ 13, 18, -10 }, { 13, 19, -12 }, { 15, 19, -12 },
+		{ 19, 20, -12 }
+		}
+	},
+	/* 10BPP/14BPC */
+	{ 410, 15, 5632, 15, 24, 23, 23, {
+		{ 0, 11, 2 }, { 5, 13, 0 }, { 11, 15, 0 }, { 13, 18, -2 },
+		{ 15, 19, -4 }, { 15, 19, -6 }, { 15, 19, -8 }, { 15, 20, -8 },
+		{ 15, 21, -8 }, { 15, 21, -10 }, { 17, 22, -10 },
+		{ 17, 22, -10 }, { 17, 23, -12 }, { 19, 23, -12 },
+		{ 23, 24, -12 }
+		}
+	},
+	/* 10BPP/16BPC */
+	{ 410, 15, 5632, 19, 28, 27, 27, {
+		{ 0, 11, 2 }, { 6, 14, 0 }, { 13, 17, 0 }, { 16, 20, -2 },
+		{ 19, 23, -4 }, { 19, 23, -6 }, { 19, 23, -8 }, { 19, 24, -8 },
+		{ 19, 25, -8 }, { 19, 25, -10 }, { 21, 26, -10 },
+		{ 21, 26, -10 }, { 21, 27, -12 }, { 23, 27, -12 },
+		{ 27, 28, -12 }
+		}
+	},
+},
+{
+	/* 12BPP/8BPC */
+	{ 341, 15, 2048, 3, 12, 11, 11, {
+		{ 0, 2, 2 }, { 0, 4, 0 }, { 1, 5, 0 }, { 1, 6, -2 },
+		{ 3, 7, -4 }, { 3, 7, -6 }, { 3, 7, -8 }, { 3, 8, -8 },
+		{ 3, 9, -8 }, { 3, 10, -10 }, { 5, 11, -10 },
+		{ 5, 12, -12 }, { 5, 13, -12 }, { 7, 13, -12 }, { 13, 15, -12 }
+		}
+	},
+	/* 12BPP/10BPC */
+	{ 341, 15, 2048, 7, 16, 15, 15, {
+		{ 0, 2, 2 }, { 2, 5, 0 }, { 3, 7, 0 }, { 4, 8, -2 },
+		{ 6, 9, -4 }, { 7, 10, -6 }, { 7, 11, -8 }, { 7, 12, -8 },
+		{ 7, 13, -8 }, { 7, 14, -10 }, { 9, 15, -10 }, { 9, 16, -12 },
+		{ 9, 17, -12 }, { 11, 17, -12 }, { 17, 19, -12 }
+		}
+	},
+	/* 12BPP/12BPC */
+	{ 341, 15, 2048, 11, 20, 19, 19, {
+		{ 0, 6, 2 }, { 4, 9, 0 }, { 7, 11, 0 }, { 8, 12, -2 },
+		{ 10, 13, -4 }, { 11, 14, -6 }, { 11, 15, -8 }, { 11, 16, -8 },
+		{ 11, 17, -8 }, { 11, 18, -10 }, { 13, 19, -10 },
+		{ 13, 20, -12 }, { 13, 21, -12 }, { 15, 21, -12 },
+		{ 21, 23, -12 }
+		}
+	},
+	/* 12BPP/14BPC */
+	{ 341, 15, 2048, 15, 24, 23, 23, {
+		{ 0, 6, 2 }, { 7, 10, 0 }, { 9, 13, 0 }, { 11, 16, -2 },
+		{ 14, 17, -4 }, { 15, 18, -6 }, { 15, 19, -8 }, { 15, 20, -8 },
+		{ 15, 20, -8 }, { 15, 21, -10 }, { 17, 21, -10 },
+		{ 17, 21, -12 }, { 17, 21, -12 }, { 19, 22, -12 },
+		{ 22, 23, -12 }
+		}
+	},
+	/* 12BPP/16BPC */
+	{ 341, 15, 2048, 19, 28, 27, 27, {
+		{ 0, 6, 2 }, { 6, 11, 0 }, { 11, 15, 0 }, { 14, 18, -2 },
+		{ 18, 21, -4 }, { 19, 22, -6 }, { 19, 23, -8 }, { 19, 24, -8 },
+		{ 19, 24, -8 }, { 19, 25, -10 }, { 21, 25, -10 },
+		{ 21, 25, -12 }, { 21, 25, -12 }, { 23, 26, -12 },
+		{ 26, 27, -12 }
+		}
+	},
+},
+{
+	/* 15BPP/8BPC */
+	{ 273, 15, 2048, 3, 12, 11, 11, {
+		{ 0, 0, 10 }, { 0, 1, 8 }, { 0, 1, 6 }, { 0, 2, 4 },
+		{ 1, 2, 2 }, { 1, 3, 0 }, { 1, 3, -2 }, { 2, 4, -4 },
+		{ 2, 5, -6 }, { 3, 5, -8 }, { 4, 6, -10 }, { 4, 7, -10 },
+		{ 5, 7, -12 }, { 7, 8, -12 }, { 8, 9, -12 }
+		}
+	},
+	/* 15BPP/10BPC */
+	{ 273, 15, 2048, 7, 16, 15, 15, {
+		{ 0, 2, 10 }, { 2, 5, 8 }, { 3, 5, 6 }, { 4, 6, 4 },
+		{ 5, 6, 2 }, { 5, 7, 0 }, { 5, 7, -2 }, { 6, 8, -4 },
+		{ 6, 9, -6 }, { 7, 9, -8 }, { 8, 10, -10 }, { 8, 11, -10 },
+		{ 9, 11, -12 }, { 11, 12, -12 }, { 12, 13, -12 }
+		}
+	},
+	/* 15BPP/12BPC */
+	{ 273, 15, 2048, 11, 20, 19, 19, {
+		{ 0, 4, 10 }, { 2, 7, 8 }, { 4, 9, 6 }, { 6, 11, 4 },
+		{ 9, 11, 2 }, { 9, 11, 0 }, { 9, 12, -2 }, { 10, 12, -4 },
+		{ 11, 13, -6 }, { 11, 13, -8 }, { 12, 14, -10 },
+		{ 13, 15, -10 }, { 13, 15, -12 }, { 15, 16, -12 },
+		{ 16, 17, -12 }
+		}
+	},
+	/* 15BPP/14BPC */
+	{ 273, 15, 2048, 15, 24, 23, 23, {
+		{ 0, 4, 10 }, { 3, 8, 8 }, { 6, 11, 6 }, { 9, 14, 4 },
+		{ 13, 15, 2 }, { 13, 15, 0 }, { 13, 16, -2 }, { 14, 16, -4 },
+		{ 15, 17, -6 }, { 15, 17, -8 }, { 16, 18, -10 },
+		{ 17, 19, -10 }, { 17, 19, -12 }, { 19, 20, -12 },
+		{ 20, 21, -12 }
+		}
+	},
+	/* 15BPP/16BPC */
+	{ 273, 15, 2048, 19, 28, 27, 27, {
+		{ 0, 4, 10 }, { 4, 9, 8 }, { 8, 13, 6 }, { 12, 17, 4 },
+		{ 17, 19, 2 }, { 17, 20, 0 }, { 17, 20, -2 }, { 18, 20, -4 },
+		{ 19, 21, -6 }, { 19, 21, -8 }, { 20, 22, -10 },
+		{ 21, 23, -10 }, { 21, 23, -12 }, { 23, 24, -12 },
+		{ 24, 25, -12 }
+		}
+	}
+}
+
+};
+
+static int get_row_index_for_rc_params(u16 compressed_bpp)
+{
+	switch (compressed_bpp) {
+	case 6:
+		return ROW_INDEX_6BPP;
+	case 8:
+		return ROW_INDEX_8BPP;
+	case 10:
+		return ROW_INDEX_10BPP;
+	case 12:
+		return ROW_INDEX_12BPP;
+	case 15:
+		return ROW_INDEX_15BPP;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int get_column_index_for_rc_params(u8 bits_per_component)
+{
+	switch (bits_per_component) {
+	case 8:
+		return COLUMN_INDEX_8BPC;
+	case 10:
+		return COLUMN_INDEX_10BPC;
+	case 12:
+		return COLUMN_INDEX_12BPC;
+	case 14:
+		return COLUMN_INDEX_14BPC;
+	case 16:
+		return COLUMN_INDEX_16BPC;
+	default:
+		return -EINVAL;
+	}
+}
+
+int intel_dp_compute_dsc_params(struct intel_dp *intel_dp,
+				struct intel_crtc_state *pipe_config)
+{
+	struct drm_dsc_config *vdsc_cfg = &pipe_config->dp_dsc_cfg;
+	u16 compressed_bpp = pipe_config->dsc_params.compressed_bpp;
+	u8 i = 0;
+	int row_index = 0;
+	int column_index = 0;
+	u8 line_buf_depth = 0;
+
+	vdsc_cfg->pic_width = pipe_config->base.adjusted_mode.crtc_hdisplay;
+	vdsc_cfg->pic_height = pipe_config->base.adjusted_mode.crtc_vdisplay;
+	vdsc_cfg->slice_width = DIV_ROUND_UP(vdsc_cfg->pic_width,
+					     pipe_config->dsc_params.slice_count);
+	/*
+	 * Slice Height of 8 works for all currently available panels. So start
+	 * with that if pic_height is an integral multiple of 8.
+	 * Eventually add logic to try multiple slice heights.
+	 */
+	if (vdsc_cfg->pic_height % 8 == 0)
+		vdsc_cfg->slice_height = 8;
+	else if (vdsc_cfg->pic_height % 4 == 0)
+		vdsc_cfg->slice_height = 4;
+	else
+		vdsc_cfg->slice_height = 2;
+
+	/* Values filled from DSC Sink DPCD */
+	vdsc_cfg->dsc_version_major =
+		(intel_dp->dsc_dpcd[DP_DSC_REV - DP_DSC_SUPPORT] &
+		 DP_DSC_MAJOR_MASK) >> DP_DSC_MAJOR_SHIFT;
+	vdsc_cfg->dsc_version_minor =
+		min(DSC_SUPPORTED_VERSION_MIN,
+		    (intel_dp->dsc_dpcd[DP_DSC_REV - DP_DSC_SUPPORT] &
+		     DP_DSC_MINOR_MASK) >> DP_DSC_MINOR_SHIFT);
+
+	vdsc_cfg->convert_rgb = intel_dp->dsc_dpcd[DP_DSC_DEC_COLOR_FORMAT_CAP - DP_DSC_SUPPORT] &
+		DP_DSC_RGB;
+
+	line_buf_depth = drm_dp_dsc_sink_line_buf_depth(intel_dp->dsc_dpcd);
+	if (!line_buf_depth) {
+		DRM_DEBUG_KMS("DSC Sink Line Buffer Depth invalid\n");
+		return -EINVAL;
+	}
+	if (vdsc_cfg->dsc_version_minor == 2)
+		vdsc_cfg->line_buf_depth = (line_buf_depth == DSC_1_2_MAX_LINEBUF_DEPTH_BITS) ?
+			DSC_1_2_MAX_LINEBUF_DEPTH_VAL : line_buf_depth;
+	else
+		vdsc_cfg->line_buf_depth = (line_buf_depth > DSC_1_1_MAX_LINEBUF_DEPTH_BITS) ?
+			DSC_1_1_MAX_LINEBUF_DEPTH_BITS : line_buf_depth;
+
+	/* Gen 11 does not support YCbCr */
+	vdsc_cfg->enable422 = false;
+	/* Gen 11 does not support VBR */
+	vdsc_cfg->vbr_enable = false;
+	vdsc_cfg->block_pred_enable =
+			intel_dp->dsc_dpcd[DP_DSC_BLK_PREDICTION_SUPPORT - DP_DSC_SUPPORT] &
+		DP_DSC_BLK_PREDICTION_IS_SUPPORTED;
+
+	/* Gen 11 only supports integral values of bpp */
+	vdsc_cfg->bits_per_pixel = compressed_bpp << 4;
+	vdsc_cfg->bits_per_component = pipe_config->pipe_bpp / 3;
+
+	for (i = 0; i < DSC_NUM_BUF_RANGES - 1; i++) {
+		/*
+		 * six 0s are appended to the lsb of each threshold value
+		 * internally in h/w.
+		 * Only 8 bits are allowed for programming RcBufThreshold
+		 */
+		vdsc_cfg->rc_buf_thresh[i] = rc_buf_thresh[i] >> 6;
+	}
+
+	/*
+	 * For 6bpp, RC Buffer threshold 12 and 13 need a different value
+	 * as per C Model
+	 */
+	if (compressed_bpp == 6) {
+		vdsc_cfg->rc_buf_thresh[12] = 0x7C;
+		vdsc_cfg->rc_buf_thresh[13] = 0x7D;
+	}
+
+	row_index = get_row_index_for_rc_params(compressed_bpp);
+	column_index =
+		get_column_index_for_rc_params(vdsc_cfg->bits_per_component);
+
+	if (row_index < 0 || column_index < 0)
+		return -EINVAL;
+
+	vdsc_cfg->first_line_bpg_offset =
+		rc_params[row_index][column_index].first_line_bpg_offset;
+	vdsc_cfg->initial_xmit_delay =
+		rc_params[row_index][column_index].initial_xmit_delay;
+	vdsc_cfg->initial_offset =
+		rc_params[row_index][column_index].initial_offset;
+	vdsc_cfg->flatness_min_qp =
+		rc_params[row_index][column_index].flatness_min_qp;
+	vdsc_cfg->flatness_max_qp =
+		rc_params[row_index][column_index].flatness_max_qp;
+	vdsc_cfg->rc_quant_incr_limit0 =
+		rc_params[row_index][column_index].rc_quant_incr_limit0;
+	vdsc_cfg->rc_quant_incr_limit1 =
+		rc_params[row_index][column_index].rc_quant_incr_limit1;
+
+	for (i = 0; i < DSC_NUM_BUF_RANGES; i++) {
+		vdsc_cfg->rc_range_params[i].range_min_qp =
+			rc_params[row_index][column_index].rc_range_params[i].range_min_qp;
+		vdsc_cfg->rc_range_params[i].range_max_qp =
+			rc_params[row_index][column_index].rc_range_params[i].range_max_qp;
+		/*
+		 * Range BPG Offset uses 2's complement and is only a 6 bits. So
+		 * mask it to get only 6 bits.
+		 */
+		vdsc_cfg->rc_range_params[i].range_bpg_offset =
+			rc_params[row_index][column_index].rc_range_params[i].range_bpg_offset &
+			DSC_RANGE_BPG_OFFSET_MASK;
+	}
+
+	/*
+	 * BitsPerComponent value determines mux_word_size:
+	 * When BitsPerComponent is 12bpc, muxWordSize will be equal to 64 bits
+	 * When BitsPerComponent is 8 or 10bpc, muxWordSize will be equal to
+	 * 48 bits
+	 */
+	if (vdsc_cfg->bits_per_component == 8 ||
+	    vdsc_cfg->bits_per_component == 10)
+		vdsc_cfg->mux_word_size = DSC_MUX_WORD_SIZE_8_10_BPC;
+	else if (vdsc_cfg->bits_per_component == 12)
+		vdsc_cfg->mux_word_size = DSC_MUX_WORD_SIZE_12_BPC;
+
+	/* RC_MODEL_SIZE is a constant across all configurations */
+	vdsc_cfg->rc_model_size = DSC_RC_MODEL_SIZE_CONST;
+	/* InitialScaleValue is a 6 bit value with 3 fractional bits (U3.3) */
+	vdsc_cfg->initial_scale_value = (vdsc_cfg->rc_model_size << 3) /
+		(vdsc_cfg->rc_model_size - vdsc_cfg->initial_offset);
+
+	return 0;
+}
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

✗ Fi.CI.CHECKPATCH: warning for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev3)

[Patchwork]

== Series Details ==

Series: series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev3)
URL   : https://patchwork.freedesktop.org/series/53184/
State : warning

== Summary ==

$ dim checkpatch origin/drm-tip
cf74ed403002 drm/i915/dp: Add DSC params and DSC config to intel_crtc_state
-:49: CHECK:BOOL_MEMBER: Avoid using bool structure members because of possible alignment issues - see: https://lkml.org/lkml/2017/11/21/384
#49: FILE: drivers/gpu/drm/i915/intel_drv.h:948:
+		bool compression_enable;

-:50: CHECK:BOOL_MEMBER: Avoid using bool structure members because of possible alignment issues - see: https://lkml.org/lkml/2017/11/21/384
#50: FILE: drivers/gpu/drm/i915/intel_drv.h:949:
+		bool dsc_split;

total: 0 errors, 0 warnings, 2 checks, 22 lines checked
f4c722992aee drm/i915/dp: Compute DSC pipe config in atomic check
ce2f079b691f drm/i915/dp: Do not enable PSR2 if DSC is enabled
4578253d135c drm/i915/dsc: Define & Compute VESA DSC params
-:68: WARNING:BAD_SIGN_OFF: Non-standard signature: Co-developed-by:
#68: 
Co-developed-by: Manasi Navare <manasi.d.navare@intel.com>

-:119: WARNING:FILE_PATH_CHANGES: added, moved or deleted file(s), does MAINTAINERS need updating?
#119: 
new file mode 100644

total: 0 errors, 2 warnings, 0 checks, 488 lines checked
e6dd78c8b893 drm/i915/dsc: Compute Rate Control parameters for DSC
b4cbbbfeb28a drm/i915/dp: Enable/Disable DSC in DP Sink
d9ac811835a4 drm/i915/dsc: Add a power domain for VDSC on eDP/MIPI DSI
51aa0ec34c42 drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling
-:391: WARNING:LONG_LINE: line over 100 characters
#391: FILE: drivers/gpu/drm/i915/intel_vdsc.c:897:
+		rc_range_params_dword[i / 2] |= (u32)(((vdsc_cfg->rc_range_params[i].range_bpg_offset <<

total: 0 errors, 1 warnings, 0 checks, 426 lines checked
030d1fd500a0 drm/i915/dp: Use the existing write_infoframe() for DSC PPS SDPs
924582574b2f drm/i915/dp: Populate DSC PPS SDP and send PPS infoframes
d2c1b3c51630 drm/i915/dp: Configure Display stream splitter registers during DSC enable
0c808e718014 drm/i915/dp: Disable DSC in source by disabling DSS CTL bits
8f9d717516c7 drm/i915/dsc: Enable and disable appropriate power wells for VDSC
7c08c67d8ce9 i915/dp/fec: Add fec_enable to the crtc state.
-:126: CHECK:BOOL_MEMBER: Avoid using bool structure members because of possible alignment issues - see: https://lkml.org/lkml/2017/11/21/384
#126: FILE: drivers/gpu/drm/i915/intel_drv.h:956:
+	bool fec_enable;

total: 0 errors, 0 warnings, 1 checks, 65 lines checked
f8545a54cbcb drm/i915/fec: Set FEC_READY in FEC_CONFIGURATION
fd072dec2471 i915/dp/fec: Configure the Forward Error Correction bits.
bbc5b58c45f5 drm/i915/fec: Disable FEC state.

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

✗ Fi.CI.SPARSE: warning for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev3)

[Patchwork]

== Series Details ==

Series: series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev3)
URL   : https://patchwork.freedesktop.org/series/53184/
State : warning

== Summary ==

$ dim sparse origin/drm-tip
Sparse version: v0.5.2
Commit: drm/i915/dp: Add DSC params and DSC config to intel_crtc_state
-drivers/gpu/drm/i915/selftests/../i915_drv.h:3566:16: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/selftests/../i915_drv.h:3567:16: warning: expression using sizeof(void)

Commit: drm/i915/dp: Compute DSC pipe config in atomic check
+drivers/gpu/drm/i915/intel_dp.c:1896:23: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/intel_dp.c:1916:25: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/intel_dp.c:1916:25: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/intel_dp.c:1938:58: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/intel_dp.c:1938:58: warning: expression using sizeof(void)

Commit: drm/i915/dp: Do not enable PSR2 if DSC is enabled
Okay!

Commit: drm/i915/dsc: Define & Compute VESA DSC params
+drivers/gpu/drm/i915/intel_vdsc.c:352:17: warning: expression using sizeof(void)
+./include/uapi/linux/perf_event.h:147:56: warning: cast truncates bits from constant value (8000000000000000 becomes 0)

Commit: drm/i915/dsc: Compute Rate Control parameters for DSC
Okay!

Commit: drm/i915/dp: Enable/Disable DSC in DP Sink
Okay!

Commit: drm/i915/dsc: Add a power domain for VDSC on eDP/MIPI DSI
Okay!

Commit: drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling
-drivers/gpu/drm/i915/selftests/../i915_drv.h:3567:16: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/selftests/../i915_drv.h:3569:16: warning: expression using sizeof(void)

Commit: drm/i915/dp: Use the existing write_infoframe() for DSC PPS SDPs
Okay!

Commit: drm/i915/dp: Populate DSC PPS SDP and send PPS infoframes
Okay!

Commit: drm/i915/dp: Configure Display stream splitter registers during DSC enable
Okay!

Commit: drm/i915/dp: Disable DSC in source by disabling DSS CTL bits
-drivers/gpu/drm/i915/selftests/../i915_drv.h:3569:16: warning: expression using sizeof(void)
+drivers/gpu/drm/i915/selftests/../i915_drv.h:3570:16: warning: expression using sizeof(void)

Commit: drm/i915/dsc: Enable and disable appropriate power wells for VDSC
Okay!

Commit: i915/dp/fec: Add fec_enable to the crtc state.
Okay!

Commit: drm/i915/fec: Set FEC_READY in FEC_CONFIGURATION
Okay!

Commit: i915/dp/fec: Configure the Forward Error Correction bits.
Okay!

Commit: drm/i915/fec: Disable FEC state.
Okay!

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

✓ Fi.CI.BAT: success for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev3)

[Patchwork]

== Series Details ==

Series: series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev3)
URL   : https://patchwork.freedesktop.org/series/53184/
State : success

== Summary ==

CI Bug Log - changes from CI_DRM_5224 -> Patchwork_10963
====================================================

Summary
-------

  **SUCCESS**

  No regressions found.

  External URL: https://patchwork.freedesktop.org/api/1.0/series/53184/revisions/3/mbox/

Known issues
------------

  Here are the changes found in Patchwork_10963 that come from known issues:

### IGT changes ###

#### Issues hit ####

  * igt@kms_pipe_crc_basic@nonblocking-crc-pipe-a:
    - fi-byt-clapper:     PASS -> FAIL [fdo#107362]

  
#### Possible fixes ####

  * igt@kms_pipe_crc_basic@nonblocking-crc-pipe-a-frame-sequence:
    - fi-byt-clapper:     FAIL [fdo#103191] / [fdo#107362] -> PASS

  
  [fdo#103191]: https://bugs.freedesktop.org/show_bug.cgi?id=103191
  [fdo#107362]: https://bugs.freedesktop.org/show_bug.cgi?id=107362


Participating hosts (50 -> 44)
------------------------------

  Missing    (6): fi-kbl-soraka fi-ilk-m540 fi-hsw-4200u fi-byt-squawks fi-bsw-cyan fi-ctg-p8600 


Build changes
-------------

    * Linux: CI_DRM_5224 -> Patchwork_10963

  CI_DRM_5224: 67ee0d0da79f5b32636d496fd2127da1eecf6262 @ git://anongit.freedesktop.org/gfx-ci/linux
  IGT_4736: 285ebfb3b7adc56586031afa5150c4e5ad40c229 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
  Patchwork_10963: bbc5b58c45f5879b861b2c8b01493a0bc958170a @ git://anongit.freedesktop.org/gfx-ci/linux


== Linux commits ==

bbc5b58c45f5 drm/i915/fec: Disable FEC state.
fd072dec2471 i915/dp/fec: Configure the Forward Error Correction bits.
f8545a54cbcb drm/i915/fec: Set FEC_READY in FEC_CONFIGURATION
7c08c67d8ce9 i915/dp/fec: Add fec_enable to the crtc state.
8f9d717516c7 drm/i915/dsc: Enable and disable appropriate power wells for VDSC
0c808e718014 drm/i915/dp: Disable DSC in source by disabling DSS CTL bits
d2c1b3c51630 drm/i915/dp: Configure Display stream splitter registers during DSC enable
924582574b2f drm/i915/dp: Populate DSC PPS SDP and send PPS infoframes
030d1fd500a0 drm/i915/dp: Use the existing write_infoframe() for DSC PPS SDPs
51aa0ec34c42 drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling
d9ac811835a4 drm/i915/dsc: Add a power domain for VDSC on eDP/MIPI DSI
b4cbbbfeb28a drm/i915/dp: Enable/Disable DSC in DP Sink
e6dd78c8b893 drm/i915/dsc: Compute Rate Control parameters for DSC
4578253d135c drm/i915/dsc: Define & Compute VESA DSC params
ce2f079b691f drm/i915/dp: Do not enable PSR2 if DSC is enabled
f4c722992aee drm/i915/dp: Compute DSC pipe config in atomic check
cf74ed403002 drm/i915/dp: Add DSC params and DSC config to intel_crtc_state

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10963/
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

Re: [CI v13 01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state

[Manasi Navare]

Pushed to dinq, thanks for the patch and the review.

Manasi

On Wed, Nov 28, 2018 at 12:26:12PM -0800, Manasi Navare wrote:
> Basic DSC parameters and DSC configuration data needs to be computed
> for each of the requested mode during atomic check. This is
> required since for certain modes, valid DSC parameters and config
> data might not be computed in which case compression cannot be
> enabled for that mode.
> For that reason we need to add these params and config structure
> to the intel_crtc_state so that if valid this state information
> can directly be used while enabling DSC in atomic commit.
> 
> v2:
> * Rebase on drm-tip (Manasi)
> 
> Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
> Cc: Jani Nikula <jani.nikula@linux.intel.com>
> Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
> Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
> Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
> ---
>  drivers/gpu/drm/i915/i915_drv.h  | 1 +
>  drivers/gpu/drm/i915/intel_drv.h | 9 +++++++++
>  2 files changed, 10 insertions(+)
> 
> diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
> index f763b30f98d9..183aae996305 100644
> --- a/drivers/gpu/drm/i915/i915_drv.h
> +++ b/drivers/gpu/drm/i915/i915_drv.h
> @@ -53,6 +53,7 @@
>  #include <drm/drm_auth.h>
>  #include <drm/drm_cache.h>
>  #include <drm/drm_util.h>
> +#include <drm/drm_dsc.h>
>  
>  #include "i915_fixed.h"
>  #include "i915_params.h"
> diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
> index a62d77b76291..270212fa43a0 100644
> --- a/drivers/gpu/drm/i915/intel_drv.h
> +++ b/drivers/gpu/drm/i915/intel_drv.h
> @@ -937,6 +937,15 @@ struct intel_crtc_state {
>  
>  	/* Output down scaling is done in LSPCON device */
>  	bool lspcon_downsampling;
> +
> +	/* Display Stream compression state */
> +	struct {
> +		bool compression_enable;
> +		bool dsc_split;
> +		u16 compressed_bpp;
> +		u8 slice_count;
> +	} dsc_params;
> +	struct drm_dsc_config dp_dsc_cfg;
>  };
>  
>  struct intel_crtc {
> -- 
> 2.19.1
> 
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

✗ Fi.CI.IGT: failure for series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev3)

[Patchwork]

== Series Details ==

Series: series starting with [CI,v13,01/17] drm/i915/dp: Add DSC params and DSC config to intel_crtc_state (rev3)
URL   : https://patchwork.freedesktop.org/series/53184/
State : failure

== Summary ==

CI Bug Log - changes from CI_DRM_5224_full -> Patchwork_10963_full
====================================================

Summary
-------

  **FAILURE**

  Serious unknown changes coming with Patchwork_10963_full absolutely need to be
  verified manually.
  
  If you think the reported changes have nothing to do with the changes
  introduced in Patchwork_10963_full, please notify your bug team to allow them
  to document this new failure mode, which will reduce false positives in CI.

  

Possible new issues
-------------------

  Here are the unknown changes that may have been introduced in Patchwork_10963_full:

### IGT changes ###

#### Possible regressions ####

  * igt@gem_eio@reset-stress:
    - shard-glk:          PASS -> FAIL

  
#### Warnings ####

  * igt@pm_rc6_residency@rc6-accuracy:
    - shard-snb:          SKIP -> PASS

  
Known issues
------------

  Here are the changes found in Patchwork_10963_full that come from known issues:

### IGT changes ###

#### Issues hit ####

  * igt@gem_exec_schedule@pi-ringfull-bsd:
    - shard-skl:          NOTRUN -> FAIL [fdo#103158] +1

  * igt@gem_ppgtt@blt-vs-render-ctx0:
    - shard-skl:          PASS -> TIMEOUT [fdo#108039]

  * igt@kms_busy@extended-modeset-hang-newfb-render-a:
    - {shard-iclb}:       PASS -> DMESG-WARN [fdo#107956]

  * igt@kms_busy@extended-modeset-hang-newfb-render-b:
    - shard-skl:          NOTRUN -> DMESG-WARN [fdo#107956]

  * igt@kms_ccs@pipe-a-crc-sprite-planes-basic:
    - shard-glk:          PASS -> FAIL [fdo#108145]

  * igt@kms_cursor_crc@cursor-128x128-sliding:
    - shard-skl:          NOTRUN -> FAIL [fdo#103232]

  * igt@kms_cursor_crc@cursor-256x256-random:
    - shard-glk:          PASS -> FAIL [fdo#103232] +1

  * igt@kms_draw_crc@draw-method-xrgb2101010-mmap-cpu-untiled:
    - shard-skl:          PASS -> FAIL [fdo#103184]

  * igt@kms_flip@flip-vs-expired-vblank-interruptible:
    - shard-skl:          NOTRUN -> FAIL [fdo#105363]

  * igt@kms_flip@plain-flip-fb-recreate-interruptible:
    - shard-skl:          PASS -> FAIL [fdo#100368]

  * igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-draw-mmap-cpu:
    - shard-apl:          PASS -> FAIL [fdo#103167] +1

  * igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-draw-mmap-gtt:
    - shard-glk:          PASS -> FAIL [fdo#103167] +2

  * igt@kms_frontbuffer_tracking@psr-1p-primscrn-spr-indfb-draw-blt:
    - {shard-iclb}:       PASS -> FAIL [fdo#103167] +1

  * igt@kms_plane_alpha_blend@pipe-b-alpha-7efc:
    - shard-skl:          NOTRUN -> FAIL [fdo#107815] / [fdo#108145]

  * igt@kms_plane_alpha_blend@pipe-b-constant-alpha-min:
    - shard-skl:          NOTRUN -> FAIL [fdo#108145]

  * igt@kms_plane_multiple@atomic-pipe-c-tiling-y:
    - shard-glk:          PASS -> FAIL [fdo#103166] +1
    - shard-apl:          PASS -> FAIL [fdo#103166] +1

  * igt@kms_psr@suspend:
    - shard-skl:          PASS -> INCOMPLETE [fdo#107773]

  * igt@kms_rmfb@close-fd:
    - {shard-iclb}:       PASS -> DMESG-WARN [fdo#107724] +1

  * igt@kms_setmode@basic:
    - shard-apl:          PASS -> FAIL [fdo#99912]

  * igt@kms_vblank@pipe-c-ts-continuation-suspend:
    - shard-hsw:          PASS -> FAIL [fdo#104894]

  * igt@pm_rpm@legacy-planes:
    - {shard-iclb}:       PASS -> DMESG-WARN [fdo#108654]

  * igt@pm_rpm@modeset-lpsp-stress:
    - shard-skl:          PASS -> INCOMPLETE [fdo#107807]

  * {igt@runner@aborted}:
    - {shard-iclb}:       NOTRUN -> ( 2 FAIL ) [fdo#108315] / [fdo#108756]

  
#### Possible fixes ####

  * igt@gem_userptr_blits@readonly-unsync:
    - shard-skl:          TIMEOUT [fdo#108887] -> PASS

  * igt@kms_busy@extended-pageflip-hang-newfb-render-b:
    - shard-apl:          DMESG-WARN [fdo#107956] -> PASS

  * igt@kms_ccs@pipe-b-crc-sprite-planes-basic:
    - shard-glk:          FAIL [fdo#108145] -> PASS

  * igt@kms_cursor_crc@cursor-64x64-onscreen:
    - shard-apl:          FAIL [fdo#103232] -> PASS

  * igt@kms_cursor_crc@cursor-size-change:
    - shard-glk:          FAIL [fdo#103232] -> PASS +1

  * igt@kms_flip@2x-modeset-vs-vblank-race-interruptible:
    - shard-glk:          FAIL [fdo#103060] -> PASS

  * igt@kms_frontbuffer_tracking@fbc-2p-primscrn-cur-indfb-draw-mmap-wc:
    - shard-glk:          FAIL [fdo#103167] -> PASS

  * igt@kms_frontbuffer_tracking@psr-1p-primscrn-spr-indfb-draw-mmap-wc:
    - {shard-iclb}:       FAIL [fdo#103167] -> PASS

  * igt@kms_plane_alpha_blend@pipe-b-coverage-7efc:
    - shard-skl:          FAIL [fdo#107815] -> PASS

  * igt@pm_rpm@modeset-non-lpsp-stress-no-wait:
    - shard-skl:          INCOMPLETE [fdo#107807] -> SKIP

  * igt@pm_rpm@system-suspend-execbuf:
    - shard-skl:          INCOMPLETE [fdo#104108] / [fdo#107807] -> PASS

  
#### Warnings ####

  * igt@i915_selftest@live_contexts:
    - {shard-iclb}:       DMESG-FAIL [fdo#108569] -> INCOMPLETE [fdo#108315]

  
  {name}: This element is suppressed. This means it is ignored when computing
          the status of the difference (SUCCESS, WARNING, or FAILURE).

  [fdo#100368]: https://bugs.freedesktop.org/show_bug.cgi?id=100368
  [fdo#103060]: https://bugs.freedesktop.org/show_bug.cgi?id=103060
  [fdo#103158]: https://bugs.freedesktop.org/show_bug.cgi?id=103158
  [fdo#103166]: https://bugs.freedesktop.org/show_bug.cgi?id=103166
  [fdo#103167]: https://bugs.freedesktop.org/show_bug.cgi?id=103167
  [fdo#103184]: https://bugs.freedesktop.org/show_bug.cgi?id=103184
  [fdo#103232]: https://bugs.freedesktop.org/show_bug.cgi?id=103232
  [fdo#104108]: https://bugs.freedesktop.org/show_bug.cgi?id=104108
  [fdo#104894]: https://bugs.freedesktop.org/show_bug.cgi?id=104894
  [fdo#105363]: https://bugs.freedesktop.org/show_bug.cgi?id=105363
  [fdo#107724]: https://bugs.freedesktop.org/show_bug.cgi?id=107724
  [fdo#107773]: https://bugs.freedesktop.org/show_bug.cgi?id=107773
  [fdo#107807]: https://bugs.freedesktop.org/show_bug.cgi?id=107807
  [fdo#107815]: https://bugs.freedesktop.org/show_bug.cgi?id=107815
  [fdo#107956]: https://bugs.freedesktop.org/show_bug.cgi?id=107956
  [fdo#108039]: https://bugs.freedesktop.org/show_bug.cgi?id=108039
  [fdo#108145]: https://bugs.freedesktop.org/show_bug.cgi?id=108145
  [fdo#108315]: https://bugs.freedesktop.org/show_bug.cgi?id=108315
  [fdo#108569]: https://bugs.freedesktop.org/show_bug.cgi?id=108569
  [fdo#108654]: https://bugs.freedesktop.org/show_bug.cgi?id=108654
  [fdo#108756]: https://bugs.freedesktop.org/show_bug.cgi?id=108756
  [fdo#108887]: https://bugs.freedesktop.org/show_bug.cgi?id=108887
  [fdo#99912]: https://bugs.freedesktop.org/show_bug.cgi?id=99912


Participating hosts (7 -> 7)
------------------------------

  No changes in participating hosts


Build changes
-------------

    * Linux: CI_DRM_5224 -> Patchwork_10963

  CI_DRM_5224: 67ee0d0da79f5b32636d496fd2127da1eecf6262 @ git://anongit.freedesktop.org/gfx-ci/linux
  IGT_4736: 285ebfb3b7adc56586031afa5150c4e5ad40c229 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
  Patchwork_10963: bbc5b58c45f5879b861b2c8b01493a0bc958170a @ git://anongit.freedesktop.org/gfx-ci/linux
  piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10963/
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx