* [U-Boot] [PATCH V2] ARM: mach-omap2: omap3: Fix GPIO clocking in SPL
@ 2018-12-14 22:28 Adam Ford
2018-12-27 15:47 ` [U-Boot] [U-Boot, " Tom Rini
0 siblings, 1 reply; 2+ messages in thread
From: Adam Ford @ 2018-12-14 22:28 UTC (permalink / raw)
To: u-boot
OMAP3_GPIO_x is needed to enable each GPIO bank on the OMAP3
boards. At one point, the #ifdef's were replaced with
if CONFIG_IS_ENABLED but this won't work for people who need
OMAP3_GPIO_x in SPL since the SPL prefix for this option isn't
used in Kconfig. This patch moves the check to #if defined and
also makes Kconfig select the banks if CMD_GPIO is used which
makes the checks in the code less cumbersome.
Fixes: bd8a9c14c91c ("arm: mach-omap2/omap3/clock.c: Enable
all GPIO with CMD_GPIO")
Reported-by: Liam O'Shaughnessy <liam.o.shaughnessy@gumstix.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
---
V2: change if defined(OMAP3_GPIO_x) to include the CONFIG_ prefix
diff --git a/arch/arm/mach-omap2/omap3/Kconfig b/arch/arm/mach-omap2/omap3/Kconfig
index e0d02fb4e5..0286b0daa3 100644
--- a/arch/arm/mach-omap2/omap3/Kconfig
+++ b/arch/arm/mach-omap2/omap3/Kconfig
@@ -3,18 +3,23 @@ if OMAP34XX
# We only enable the clocks for the GPIO banks that a given board requies.
config OMAP3_GPIO_2
bool
+ default y if CMD_GPIO
config OMAP3_GPIO_3
bool
+ default y if CMD_GPIO
config OMAP3_GPIO_4
bool
+ default y if CMD_GPIO
config OMAP3_GPIO_5
bool
+ default y if CMD_GPIO
config OMAP3_GPIO_6
bool
+ default y if CMD_GPIO
choice
prompt "OMAP3 board select"
diff --git a/arch/arm/mach-omap2/omap3/clock.c b/arch/arm/mach-omap2/omap3/clock.c
index 9a03bfa9d3..cb9e91ebc3 100644
--- a/arch/arm/mach-omap2/omap3/clock.c
+++ b/arch/arm/mach-omap2/omap3/clock.c
@@ -750,23 +750,23 @@ void per_clocks_enable(void)
setbits_le32(&prcm_base->iclken_per, 0x00000800);
#endif
-#if (CONFIG_IS_ENABLED(OMAP3_GPIO_2) || CONFIG_IS_ENABLED(CMD_GPIO))
+#if defined(CONFIG_OMAP3_GPIO_2)
setbits_le32(&prcm_base->fclken_per, 0x00002000);
setbits_le32(&prcm_base->iclken_per, 0x00002000);
#endif
-#if (CONFIG_IS_ENABLED(OMAP3_GPIO_3) || CONFIG_IS_ENABLED(CMD_GPIO))
+#if defined(CONFIG_OMAP3_GPIO_3)
setbits_le32(&prcm_base->fclken_per, 0x00004000);
setbits_le32(&prcm_base->iclken_per, 0x00004000);
#endif
-#if (CONFIG_IS_ENABLED(OMAP3_GPIO_4) || CONFIG_IS_ENABLED(CMD_GPIO))
+#if defined(CONFIG_OMAP3_GPIO_4)
setbits_le32(&prcm_base->fclken_per, 0x00008000);
setbits_le32(&prcm_base->iclken_per, 0x00008000);
#endif
-#if (CONFIG_IS_ENABLED(OMAP3_GPIO_5) || CONFIG_IS_ENABLED(CMD_GPIO))
+#if defined(CONFIG_OMAP3_GPIO_5)
setbits_le32(&prcm_base->fclken_per, 0x00010000);
setbits_le32(&prcm_base->iclken_per, 0x00010000);
#endif
-#if (CONFIG_IS_ENABLED(OMAP3_GPIO_6) || CONFIG_IS_ENABLED(CMD_GPIO))
+#if defined(CONFIG_OMAP3_GPIO_6)
setbits_le32(&prcm_base->fclken_per, 0x00020000);
setbits_le32(&prcm_base->iclken_per, 0x00020000);
#endif
--
2.17.1
^ permalink raw reply related [flat|nested] 2+ messages in thread
* [U-Boot] [U-Boot, V2] ARM: mach-omap2: omap3: Fix GPIO clocking in SPL
2018-12-14 22:28 [U-Boot] [PATCH V2] ARM: mach-omap2: omap3: Fix GPIO clocking in SPL Adam Ford
@ 2018-12-27 15:47 ` Tom Rini
0 siblings, 0 replies; 2+ messages in thread
From: Tom Rini @ 2018-12-27 15:47 UTC (permalink / raw)
To: u-boot
On Fri, Dec 14, 2018 at 04:28:30PM -0600, Adam Ford wrote:
> OMAP3_GPIO_x is needed to enable each GPIO bank on the OMAP3
> boards. At one point, the #ifdef's were replaced with
> if CONFIG_IS_ENABLED but this won't work for people who need
> OMAP3_GPIO_x in SPL since the SPL prefix for this option isn't
> used in Kconfig. This patch moves the check to #if defined and
> also makes Kconfig select the banks if CMD_GPIO is used which
> makes the checks in the code less cumbersome.
>
> Fixes: bd8a9c14c91c ("arm: mach-omap2/omap3/clock.c: Enable
> all GPIO with CMD_GPIO")
>
> Reported-by: Liam O'Shaughnessy <liam.o.shaughnessy@gumstix.com>
> Signed-off-by: Adam Ford <aford173@gmail.com>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20181227/606a9ffa/attachment.sig>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2018-12-27 15:47 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-12-14 22:28 [U-Boot] [PATCH V2] ARM: mach-omap2: omap3: Fix GPIO clocking in SPL Adam Ford
2018-12-27 15:47 ` [U-Boot] [U-Boot, " Tom Rini
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.