From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> To: andy.gross@linaro.org Cc: linux-leds@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-rockchip@lists.infradead.org, linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org, daniel.thompson@linaro.org, amit.kucheria@linaro.org, linus.walleij@linaro.org, koen.kooi@linaro.org, nicolas.dechesne@linaro.org Subject: Re: [PATCH v3 7/7] arm64: dts: qcom: apq8016-sbc: Standardize LED labels Date: Fri, 21 Dec 2018 08:05:57 +0530 [thread overview] Message-ID: <20181221023554.GB3233@Mani-XPS-13-9360> (raw) In-Reply-To: <20181029094245.7886-8-manivannan.sadhasivam@linaro.org> On Mon, Oct 29, 2018 at 03:12:45PM +0530, Manivannan Sadhasivam wrote: > For all 96Boards, the following standard is used for onboard LEDs. > > green:user1 default-trigger: heartbeat > green:user2 default-trigger: mmc0/disk-activity(onboard-storage) > green:user3 default-trigger: mmc1 (SD-card) > green:user4 default-trigger: none, panic-indicator > yellow:wlan default-trigger: phy0tx > blue:bt default-trigger: hci0-power > > So lets adopt the same for APQ8016 SBC (Dragonboard410c), which is > one of the 96Boards CE platform. > Hello, Any update on this patch? Regards, Mani > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > Acked-by: Amit Kucheria <amit.kucheria@linaro.org> > --- > arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 12 ++++++------ > 1 file changed, 6 insertions(+), 6 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi > index 46feedf7c989..35f95154316b 100644 > --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi > +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi > @@ -300,28 +300,28 @@ > compatible = "gpio-leds"; > > led@1 { > - label = "apq8016-sbc:green:user1"; > + label = "green:user1"; > gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "heartbeat"; > default-state = "off"; > }; > > led@2 { > - label = "apq8016-sbc:green:user2"; > + label = "green:user2"; > gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "mmc0"; > default-state = "off"; > }; > > led@3 { > - label = "apq8016-sbc:green:user3"; > + label = "green:user3"; > gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "mmc1"; > default-state = "off"; > }; > > led@4 { > - label = "apq8016-sbc:green:user4"; > + label = "green:user4"; > gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "none"; > panic-indicator; > @@ -329,14 +329,14 @@ > }; > > led@5 { > - label = "apq8016-sbc:yellow:wlan"; > + label = "yellow:wlan"; > gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "phy0tx"; > default-state = "off"; > }; > > led@6 { > - label = "apq8016-sbc:blue:bt"; > + label = "blue:bt"; > gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "bluetooth-power"; > default-state = "off"; > -- > 2.17.1 >
WARNING: multiple messages have this Message-ID (diff)
From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> To: andy.gross@linaro.org Cc: devicetree@vger.kernel.org, daniel.thompson@linaro.org, linux-arm-msm@vger.kernel.org, linus.walleij@linaro.org, linux-kernel@vger.kernel.org, amit.kucheria@linaro.org, linux-rockchip@lists.infradead.org, koen.kooi@linaro.org, linux-leds@vger.kernel.org, nicolas.dechesne@linaro.org, linux-soc@vger.kernel.org, linux-arm-kernel@lists.infradead.org Subject: Re: [PATCH v3 7/7] arm64: dts: qcom: apq8016-sbc: Standardize LED labels Date: Fri, 21 Dec 2018 08:05:57 +0530 [thread overview] Message-ID: <20181221023554.GB3233@Mani-XPS-13-9360> (raw) In-Reply-To: <20181029094245.7886-8-manivannan.sadhasivam@linaro.org> On Mon, Oct 29, 2018 at 03:12:45PM +0530, Manivannan Sadhasivam wrote: > For all 96Boards, the following standard is used for onboard LEDs. > > green:user1 default-trigger: heartbeat > green:user2 default-trigger: mmc0/disk-activity(onboard-storage) > green:user3 default-trigger: mmc1 (SD-card) > green:user4 default-trigger: none, panic-indicator > yellow:wlan default-trigger: phy0tx > blue:bt default-trigger: hci0-power > > So lets adopt the same for APQ8016 SBC (Dragonboard410c), which is > one of the 96Boards CE platform. > Hello, Any update on this patch? Regards, Mani > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > Acked-by: Amit Kucheria <amit.kucheria@linaro.org> > --- > arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 12 ++++++------ > 1 file changed, 6 insertions(+), 6 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi > index 46feedf7c989..35f95154316b 100644 > --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi > +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi > @@ -300,28 +300,28 @@ > compatible = "gpio-leds"; > > led@1 { > - label = "apq8016-sbc:green:user1"; > + label = "green:user1"; > gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "heartbeat"; > default-state = "off"; > }; > > led@2 { > - label = "apq8016-sbc:green:user2"; > + label = "green:user2"; > gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "mmc0"; > default-state = "off"; > }; > > led@3 { > - label = "apq8016-sbc:green:user3"; > + label = "green:user3"; > gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "mmc1"; > default-state = "off"; > }; > > led@4 { > - label = "apq8016-sbc:green:user4"; > + label = "green:user4"; > gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "none"; > panic-indicator; > @@ -329,14 +329,14 @@ > }; > > led@5 { > - label = "apq8016-sbc:yellow:wlan"; > + label = "yellow:wlan"; > gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "phy0tx"; > default-state = "off"; > }; > > led@6 { > - label = "apq8016-sbc:blue:bt"; > + label = "blue:bt"; > gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>; > linux,default-trigger = "bluetooth-power"; > default-state = "off"; > -- > 2.17.1 > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2018-12-21 2:35 UTC|newest] Thread overview: 50+ messages / expand[flat|nested] mbox.gz Atom feed top 2018-10-29 9:42 [PATCH v3 0/7] Standardize onboard LED support for 96Boards Manivannan Sadhasivam 2018-10-29 9:42 ` Manivannan Sadhasivam 2018-10-29 9:42 ` [PATCH v3 1/7] arm64: dts: rockchip: ficus: Add on-board LED support Manivannan Sadhasivam 2018-10-29 9:42 ` Manivannan Sadhasivam 2018-12-11 19:11 ` Heiko Stuebner 2018-12-11 19:11 ` Heiko Stuebner 2018-10-29 9:42 ` [PATCH v3 2/7] arm64: dts: rockchip: rock960: " Manivannan Sadhasivam 2018-10-29 9:42 ` Manivannan Sadhasivam 2018-12-11 19:11 ` Heiko Stuebner 2018-12-11 19:11 ` Heiko Stuebner 2018-10-29 9:42 ` [PATCH v3 3/7] arm64: dts: hisilicon: hikey: Standardize LED labels and triggers Manivannan Sadhasivam 2018-10-29 9:42 ` Manivannan Sadhasivam 2018-10-29 9:42 ` [PATCH v3 4/7] arm64: dts: hisilicon: hikey960: " Manivannan Sadhasivam 2018-10-29 9:42 ` Manivannan Sadhasivam 2018-10-29 9:42 ` [PATCH v3 5/7] arm64: dts: hisilicon: poplar: " Manivannan Sadhasivam 2018-10-29 9:42 ` Manivannan Sadhasivam 2018-10-29 9:42 ` [PATCH v3 6/7] arm64: dts: xilinx: ultra96: " Manivannan Sadhasivam 2018-10-29 9:42 ` Manivannan Sadhasivam 2018-12-21 2:37 ` Manivannan Sadhasivam 2018-12-21 2:37 ` Manivannan Sadhasivam 2018-12-21 6:50 ` Michal Simek 2018-12-21 6:50 ` Michal Simek 2018-12-21 6:50 ` Michal Simek 2019-01-24 16:49 ` Rob Herring 2019-01-24 16:49 ` Rob Herring 2019-01-24 16:49 ` Rob Herring 2019-01-29 13:17 ` Michal Simek 2019-01-29 13:17 ` Michal Simek 2019-01-29 13:17 ` Michal Simek 2018-10-29 9:42 ` [PATCH v3 7/7] arm64: dts: qcom: apq8016-sbc: Standardize LED labels Manivannan Sadhasivam 2018-10-29 9:42 ` Manivannan Sadhasivam 2018-12-21 2:35 ` Manivannan Sadhasivam [this message] 2018-12-21 2:35 ` Manivannan Sadhasivam 2019-02-05 19:00 ` Nicolas Dechesne 2019-02-05 19:00 ` Nicolas Dechesne 2019-02-05 19:24 ` Bjorn Andersson 2019-02-05 19:24 ` Bjorn Andersson 2018-10-31 13:38 ` [PATCH v3 0/7] Standardize onboard LED support for 96Boards Linus Walleij 2018-10-31 13:38 ` Linus Walleij 2018-10-31 13:38 ` Linus Walleij 2018-10-31 15:46 ` Michal Simek 2018-10-31 21:17 ` Linus Walleij 2018-10-31 21:17 ` Linus Walleij 2018-10-31 21:17 ` Linus Walleij 2018-11-01 10:49 ` Heiko Stübner 2018-11-01 10:49 ` Heiko Stübner 2018-11-01 10:49 ` Heiko Stübner 2018-11-29 15:42 ` Wei Xu 2018-11-29 15:42 ` Wei Xu 2018-11-29 15:42 ` Wei Xu
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20181221023554.GB3233@Mani-XPS-13-9360 \ --to=manivannan.sadhasivam@linaro.org \ --cc=amit.kucheria@linaro.org \ --cc=andy.gross@linaro.org \ --cc=daniel.thompson@linaro.org \ --cc=devicetree@vger.kernel.org \ --cc=koen.kooi@linaro.org \ --cc=linus.walleij@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-arm-msm@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-leds@vger.kernel.org \ --cc=linux-rockchip@lists.infradead.org \ --cc=linux-soc@vger.kernel.org \ --cc=nicolas.dechesne@linaro.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.