[U-Boot] [PATCH v2 05/11] mtd: spi: Switch to new SPI NOR framework

[Vignesh R <vigneshr@ti.com>]

Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/defintions

Keep U-Boot feature SPI_FLASH_BAR as is.

Signed-off-by: Vignesh R <vigneshr@ti.com>
---
 common/spl/Kconfig             |  13 +-
 drivers/mtd/spi/Kconfig        |  16 ++-
 drivers/mtd/spi/Makefile       |   4 +-
 drivers/mtd/spi/sandbox.c      |  36 +++---
 drivers/mtd/spi/sf_dataflash.c |  11 +-
 drivers/mtd/spi/sf_internal.h  | 225 ++++++---------------------------
 drivers/mtd/spi/sf_probe.c     |  33 +++--
 drivers/mtd/spi/spi-nor-core.c | 220 +++++++++++++++++++++++---------
 drivers/spi/stm32_qspi.c       |   4 +-
 include/linux/mtd/spi-nor.h    |   9 ++
 include/spi_flash.h            | 105 ++++-----------
 11 files changed, 303 insertions(+), 373 deletions(-)

diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 953841ebe761..9d8405b7daa8 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -729,13 +729,24 @@ config SPL_SPI_FLASH_SUPPORT
 	  lines). This enables the drivers in drivers/mtd/spi as part of an
 	  SPL build. This normally requires SPL_SPI_SUPPORT.
 
+if SPL_SPI_FLASH_SUPPORT
+
+config SPL_SPI_FLASH_SFDP_SUPPORT
+	bool "SFDP table parsing support for SPI NOR flashes"
+	depends on !SPI_FLASH_BAR
+	help
+	 Enable support for parsing and auto discovery of parameters for
+	 SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP)
+	 tables as per JESD216 standard in SPL.
+
 config SPL_SPI_LOAD
 	bool "Support loading from SPI flash"
-	depends on SPL_SPI_FLASH_SUPPORT
 	help
 	  Enable support for loading next stage, U-Boot or otherwise, from
 	  SPI NOR in U-Boot SPL.
 
+endif # SPL_SPI_FLASH_SUPPORT
+
 config SPL_SPI_SUPPORT
 	bool "Support SPI drivers"
 	help
diff --git a/drivers/mtd/spi/Kconfig b/drivers/mtd/spi/Kconfig
index 76d5a1d11527..e3b40fc157d6 100644
--- a/drivers/mtd/spi/Kconfig
+++ b/drivers/mtd/spi/Kconfig
@@ -27,6 +27,8 @@ config SPI_FLASH_SANDBOX
 
 config SPI_FLASH
 	bool "Legacy SPI Flash Interface support"
+	depends on SPI
+	select SPI_MEM
 	help
 	  Enable the legacy SPI flash support. This will include basic
 	  standard support for things like probing, read / write, and
@@ -34,9 +36,18 @@ config SPI_FLASH
 
 	  If unsure, say N
 
+if SPI_FLASH
+
+config SPI_FLASH_SFDP_SUPPORT
+	bool "SFDP table parsing support for SPI NOR flashes"
+	depends on !SPI_FLASH_BAR
+	help
+	 Enable support for parsing and auto discovery of parameters for
+	 SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP)
+	 tables as per JESD216 standard.
+
 config SPI_FLASH_BAR
 	bool "SPI flash Bank/Extended address register support"
-	depends on SPI_FLASH
 	help
 	  Enable the SPI flash Bank/Extended address register support.
 	  Bank/Extended address registers are used to access the flash
@@ -44,13 +55,10 @@ config SPI_FLASH_BAR
 
 config SF_DUAL_FLASH
 	bool "SPI DUAL flash memory support"
-	depends on SPI_FLASH
 	help
 	  Enable this option to support two flash memories connected to a single
 	  controller. Currently Xilinx Zynq qspi supports this.
 
-if SPI_FLASH
-
 config SPI_FLASH_ATMEL
 	bool "Atmel SPI flash support"
 	help
diff --git a/drivers/mtd/spi/Makefile b/drivers/mtd/spi/Makefile
index b4c7e1c98bd5..70058d3df2b9 100644
--- a/drivers/mtd/spi/Makefile
+++ b/drivers/mtd/spi/Makefile
@@ -9,7 +9,7 @@ ifdef CONFIG_SPL_BUILD
 obj-$(CONFIG_SPL_SPI_BOOT)	+= fsl_espi_spl.o
 endif
 
-obj-$(CONFIG_SPI_FLASH) += sf_probe.o spi_flash.o spi_flash_ids.o sf.o
-obj-$(CONFIG_SPI_FLASH_DATAFLASH) += sf_dataflash.o
+obj-$(CONFIG_SPI_FLASH) += sf_probe.o spi-nor-core.o
+obj-$(CONFIG_SPI_FLASH_DATAFLASH) += sf_dataflash.o sf.o
 obj-$(CONFIG_SPI_FLASH_MTD) += sf_mtd.o
 obj-$(CONFIG_SPI_FLASH_SANDBOX) += sandbox.o
diff --git a/drivers/mtd/spi/sandbox.c b/drivers/mtd/spi/sandbox.c
index 7b9891cb981c..084c66e9840b 100644
--- a/drivers/mtd/spi/sandbox.c
+++ b/drivers/mtd/spi/sandbox.c
@@ -92,7 +92,7 @@ struct sandbox_spi_flash {
 	/* The current flash status (see STAT_XXX defines above) */
 	u16 status;
 	/* Data describing the flash we're emulating */
-	const struct spi_flash_info *data;
+	const struct flash_info *data;
 	/* The file on disk to serv up data from */
 	int fd;
 };
@@ -122,7 +122,7 @@ static int sandbox_sf_probe(struct udevice *dev)
 	/* spec = idcode:file */
 	struct sandbox_spi_flash *sbsf = dev_get_priv(dev);
 	size_t len, idname_len;
-	const struct spi_flash_info *data;
+	const struct flash_info *data;
 	struct sandbox_spi_flash_plat_data *pdata = dev_get_platdata(dev);
 	struct sandbox_state *state = state_get_current();
 	struct dm_spi_slave_platdata *slave_plat;
@@ -155,7 +155,7 @@ static int sandbox_sf_probe(struct udevice *dev)
 	idname_len = strlen(spec);
 	debug("%s: device='%s'\n", __func__, spec);
 
-	for (data = spi_flash_ids; data->name; data++) {
+	for (data = spi_nor_ids; data->name; data++) {
 		len = strlen(data->name);
 		if (idname_len != len)
 			continue;
@@ -243,43 +243,43 @@ static int sandbox_sf_process_cmd(struct sandbox_spi_flash *sbsf, const u8 *rx,
 
 	sbsf->cmd = rx[0];
 	switch (sbsf->cmd) {
-	case CMD_READ_ID:
+	case SPINOR_OP_RDID:
 		sbsf->state = SF_ID;
 		sbsf->cmd = SF_ID;
 		break;
-	case CMD_READ_ARRAY_FAST:
+	case SPINOR_OP_READ_FAST:
 		sbsf->pad_addr_bytes = 1;
-	case CMD_READ_ARRAY_SLOW:
-	case CMD_PAGE_PROGRAM:
+	case SPINOR_OP_READ:
+	case SPINOR_OP_PP:
 		sbsf->state = SF_ADDR;
 		break;
-	case CMD_WRITE_DISABLE:
+	case SPINOR_OP_WRDI:
 		debug(" write disabled\n");
 		sbsf->status &= ~STAT_WEL;
 		break;
-	case CMD_READ_STATUS:
+	case SPINOR_OP_RDSR:
 		sbsf->state = SF_READ_STATUS;
 		break;
-	case CMD_READ_STATUS1:
+	case SPINOR_OP_RDSR2:
 		sbsf->state = SF_READ_STATUS1;
 		break;
-	case CMD_WRITE_ENABLE:
+	case SPINOR_OP_WREN:
 		debug(" write enabled\n");
 		sbsf->status |= STAT_WEL;
 		break;
-	case CMD_WRITE_STATUS:
+	case SPINOR_OP_WRSR:
 		sbsf->state = SF_WRITE_STATUS;
 		break;
 	default: {
 		int flags = sbsf->data->flags;
 
 		/* we only support erase here */
-		if (sbsf->cmd == CMD_ERASE_CHIP) {
+		if (sbsf->cmd == SPINOR_OP_CHIP_ERASE) {
 			sbsf->erase_size = sbsf->data->sector_size *
 				sbsf->data->n_sectors;
-		} else if (sbsf->cmd == CMD_ERASE_4K && (flags & SECT_4K)) {
+		} else if (sbsf->cmd == SPINOR_OP_BE_4K && (flags & SECT_4K)) {
 			sbsf->erase_size = 4 << 10;
-		} else if (sbsf->cmd == CMD_ERASE_64K && !(flags & SECT_4K)) {
+		} else if (sbsf->cmd == SPINOR_OP_SE && !(flags & SECT_4K)) {
 			sbsf->erase_size = 64 << 10;
 		} else {
 			debug(" cmd unknown: %#x\n", sbsf->cmd);
@@ -380,11 +380,11 @@ static int sandbox_sf_xfer(struct udevice *dev, unsigned int bitlen,
 				return -EIO;
 			}
 			switch (sbsf->cmd) {
-			case CMD_READ_ARRAY_FAST:
-			case CMD_READ_ARRAY_SLOW:
+			case SPINOR_OP_READ_FAST:
+			case SPINOR_OP_READ:
 				sbsf->state = SF_READ;
 				break;
-			case CMD_PAGE_PROGRAM:
+			case SPINOR_OP_PP:
 				sbsf->state = SF_WRITE;
 				break;
 			default:
diff --git a/drivers/mtd/spi/sf_dataflash.c b/drivers/mtd/spi/sf_dataflash.c
index 4a60c1b2b43a..b6a2631747a9 100644
--- a/drivers/mtd/spi/sf_dataflash.c
+++ b/drivers/mtd/spi/sf_dataflash.c
@@ -18,6 +18,7 @@
 
 #include "sf_internal.h"
 
+#define CMD_READ_ID		0x9f
 /* reads can bypass the buffers */
 #define OP_READ_CONTINUOUS	0xE8
 #define OP_READ_PAGE		0xD2
@@ -441,7 +442,7 @@ static int add_dataflash(struct udevice *dev, char *name, int nr_pages,
 	return 0;
 }
 
-struct flash_info {
+struct data_flash_info {
 	char		*name;
 
 	/*
@@ -460,7 +461,7 @@ struct flash_info {
 #define IS_POW2PS	0x0001		/* uses 2^N byte pages */
 };
 
-static struct flash_info dataflash_data[] = {
+static struct data_flash_info dataflash_data[] = {
 	/*
 	 * NOTE:  chips with SUP_POW2PS (rev D and up) need two entries,
 	 * one with IS_POW2PS and the other without.  The entry with the
@@ -501,12 +502,12 @@ static struct flash_info dataflash_data[] = {
 	{ "at45db642d",  0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS},
 };
 
-static struct flash_info *jedec_probe(struct spi_slave *spi)
+static struct data_flash_info *jedec_probe(struct spi_slave *spi)
 {
 	int			tmp;
 	uint8_t			id[5];
 	uint32_t		jedec;
-	struct flash_info	*info;
+	struct data_flash_info	*info;
 	int status;
 
 	/*
@@ -583,7 +584,7 @@ static int spi_dataflash_probe(struct udevice *dev)
 {
 	struct spi_slave *spi = dev_get_parent_priv(dev);
 	struct spi_flash *spi_flash;
-	struct flash_info *info;
+	struct data_flash_info *info;
 	int status;
 
 	spi_flash = dev_get_uclass_priv(dev);
diff --git a/drivers/mtd/spi/sf_internal.h b/drivers/mtd/spi/sf_internal.h
index 46a504441751..fd00e0d1b23b 100644
--- a/drivers/mtd/spi/sf_internal.h
+++ b/drivers/mtd/spi/sf_internal.h
@@ -12,142 +12,63 @@
 #include <linux/types.h>
 #include <linux/compiler.h>
 
-/* Dual SPI flash memories - see SPI_COMM_DUAL_... */
-enum spi_dual_flash {
-	SF_SINGLE_FLASH	= 0,
-	SF_DUAL_STACKED_FLASH	= BIT(0),
-	SF_DUAL_PARALLEL_FLASH	= BIT(1),
-};
-
-enum spi_nor_option_flags {
-	SNOR_F_SST_WR		= BIT(0),
-	SNOR_F_USE_FSR		= BIT(1),
-	SNOR_F_USE_UPAGE	= BIT(3),
-};
-
-#define SPI_FLASH_3B_ADDR_LEN		3
-#define SPI_FLASH_CMD_LEN		(1 + SPI_FLASH_3B_ADDR_LEN)
-#define SPI_FLASH_16MB_BOUN		0x1000000
-
-/* CFI Manufacture ID's */
-#define SPI_FLASH_CFI_MFR_SPANSION	0x01
-#define SPI_FLASH_CFI_MFR_STMICRO	0x20
-#define SPI_FLASH_CFI_MFR_MICRON	0x2C
-#define SPI_FLASH_CFI_MFR_MACRONIX	0xc2
-#define SPI_FLASH_CFI_MFR_SST		0xbf
-#define SPI_FLASH_CFI_MFR_WINBOND	0xef
-#define SPI_FLASH_CFI_MFR_ATMEL		0x1f
-
-/* Erase commands */
-#define CMD_ERASE_4K			0x20
-#define CMD_ERASE_CHIP			0xc7
-#define CMD_ERASE_64K			0xd8
-
-/* Write commands */
-#define CMD_WRITE_STATUS		0x01
-#define CMD_PAGE_PROGRAM		0x02
-#define CMD_WRITE_DISABLE		0x04
-#define CMD_WRITE_ENABLE		0x06
-#define CMD_QUAD_PAGE_PROGRAM		0x32
-
-/* Read commands */
-#define CMD_READ_ARRAY_SLOW		0x03
-#define CMD_READ_ARRAY_FAST		0x0b
-#define CMD_READ_DUAL_OUTPUT_FAST	0x3b
-#define CMD_READ_DUAL_IO_FAST		0xbb
-#define CMD_READ_QUAD_OUTPUT_FAST	0x6b
-#define CMD_READ_QUAD_IO_FAST		0xeb
-#define CMD_READ_ID			0x9f
-#define CMD_READ_STATUS			0x05
-#define CMD_READ_STATUS1		0x35
-#define CMD_READ_CONFIG			0x35
-#define CMD_FLAG_STATUS			0x70
-
-/* Bank addr access commands */
-#ifdef CONFIG_SPI_FLASH_BAR
-# define CMD_BANKADDR_BRWR		0x17
-# define CMD_BANKADDR_BRRD		0x16
-# define CMD_EXTNADDR_WREAR		0xC5
-# define CMD_EXTNADDR_RDEAR		0xC8
-#endif
-
-/* Common status */
-#define STATUS_WIP			BIT(0)
-#define STATUS_QEB_WINSPAN		BIT(1)
-#define STATUS_QEB_MXIC			BIT(6)
-#define STATUS_PEC			BIT(7)
-#define SR_BP0				BIT(2)  /* Block protect 0 */
-#define SR_BP1				BIT(3)  /* Block protect 1 */
-#define SR_BP2				BIT(4)  /* Block protect 2 */
-
-/* Flash timeout values */
-#define SPI_FLASH_PROG_TIMEOUT		(2 * CONFIG_SYS_HZ)
-#define SPI_FLASH_PAGE_ERASE_TIMEOUT	(5 * CONFIG_SYS_HZ)
-#define SPI_FLASH_SECTOR_ERASE_TIMEOUT	(10 * CONFIG_SYS_HZ)
-
-/* SST specific */
-#ifdef CONFIG_SPI_FLASH_SST
-#define SST26_CMD_READ_BPR		0x72
-#define SST26_CMD_WRITE_BPR		0x42
-
-#define SST26_BPR_8K_NUM		4
-#define SST26_MAX_BPR_REG_LEN		(18 + 1)
-#define SST26_BOUND_REG_SIZE		((32 + SST26_BPR_8K_NUM * 8) * SZ_1K)
-
-enum lock_ctl {
-	SST26_CTL_LOCK,
-	SST26_CTL_UNLOCK,
-	SST26_CTL_CHECK
-};
-
-# define CMD_SST_BP		0x02    /* Byte Program */
-# define CMD_SST_AAI_WP		0xAD	/* Auto Address Incr Word Program */
-
-int sst_write_wp(struct spi_flash *flash, u32 offset, size_t len,
-		const void *buf);
-int sst_write_bp(struct spi_flash *flash, u32 offset, size_t len,
-		const void *buf);
-#endif
-
-#define JEDEC_MFR(info)		((info)->id[0])
-#define JEDEC_ID(info)		(((info)->id[1]) << 8 | ((info)->id[2]))
-#define JEDEC_EXT(info)		(((info)->id[3]) << 8 | ((info)->id[4]))
-#define SPI_FLASH_MAX_ID_LEN	6
+#define SPI_NOR_MAX_ID_LEN	6
+#define SPI_NOR_MAX_ADDR_WIDTH	4
 
-struct spi_flash_info {
-	/* Device name ([MANUFLETTER][DEVTYPE][DENSITY][EXTRAINFO]) */
-	const char	*name;
+struct flash_info {
+	char		*name;
 
 	/*
 	 * This array stores the ID bytes.
 	 * The first three bytes are the JEDIC ID.
 	 * JEDEC ID zero means "no ID" (mostly older chips).
 	 */
-	u8		id[SPI_FLASH_MAX_ID_LEN];
+	u8		id[SPI_NOR_MAX_ID_LEN];
 	u8		id_len;
 
-	/*
-	 * The size listed here is what works with SPINOR_OP_SE, which isn't
+	/* The size listed here is what works with SPINOR_OP_SE, which isn't
 	 * necessarily called a "sector" by the vendor.
 	 */
-	u32		sector_size;
-	u32		n_sectors;
+	unsigned int	sector_size;
+	u16		n_sectors;
 
 	u16		page_size;
+	u16		addr_width;
 
 	u16		flags;
-#define SECT_4K			BIT(0)	/* CMD_ERASE_4K works uniformly */
-#define E_FSR			BIT(1)	/* use flag status register for */
-#define SST_WR			BIT(2)	/* use SST byte/word programming */
-#define WR_QPP			BIT(3)	/* use Quad Page Program */
-#define RD_QUAD			BIT(4)	/* use Quad Read */
-#define RD_DUAL			BIT(5)	/* use Dual Read */
-#define RD_QUADIO		BIT(6)	/* use Quad IO Read */
-#define RD_DUALIO		BIT(7)	/* use Dual IO Read */
-#define RD_FULL			(RD_QUAD | RD_DUAL | RD_QUADIO | RD_DUALIO)
+#define SECT_4K			BIT(0)	/* SPINOR_OP_BE_4K works uniformly */
+#define SPI_NOR_NO_ERASE	BIT(1)	/* No erase command needed */
+#define SST_WRITE		BIT(2)	/* use SST byte programming */
+#define SPI_NOR_NO_FR		BIT(3)	/* Can't do fastread */
+#define SECT_4K_PMC		BIT(4)	/* SPINOR_OP_BE_4K_PMC works uniformly */
+#define SPI_NOR_DUAL_READ	BIT(5)	/* Flash supports Dual Read */
+#define SPI_NOR_QUAD_READ	BIT(6)	/* Flash supports Quad Read */
+#define USE_FSR			BIT(7)	/* use flag status register */
+#define SPI_NOR_HAS_LOCK	BIT(8)	/* Flash supports lock/unlock via SR */
+#define SPI_NOR_HAS_TB		BIT(9)	/*
+					 * Flash SR has Top/Bottom (TB) protect
+					 * bit. Must be used with
+					 * SPI_NOR_HAS_LOCK.
+					 */
+#define	SPI_S3AN		BIT(10)	/*
+					 * Xilinx Spartan 3AN In-System Flash
+					 * (MFR cannot be used for probing
+					 * because it has the same value as
+					 * ATMEL flashes)
+					 */
+#define SPI_NOR_4B_OPCODES	BIT(11)	/*
+					 * Use dedicated 4byte address op codes
+					 * to support memory size above 128Mib.
+					 */
+#define NO_CHIP_ERASE		BIT(12) /* Chip does not support chip erase */
+#define SPI_NOR_SKIP_SFDP	BIT(13)	/* Skip parsing of SFDP tables */
+#define USE_CLSR		BIT(14)	/* use CLSR command */
 };
 
-extern const struct spi_flash_info spi_flash_ids[];
+extern const struct flash_info spi_nor_ids[];
+
+#define JEDEC_MFR(info)	((info)->id[0])
+#define JEDEC_ID(info)		(((info)->id[1]) << 8 | ((info)->id[2]))
 
 /* Send a single-byte command to the device and read the response */
 int spi_flash_cmd(struct spi_slave *spi, u8 cmd, void *response, size_t len);
@@ -167,78 +88,12 @@ int spi_flash_cmd_write(struct spi_slave *spi, const u8 *cmd, size_t cmd_len,
 		const void *data, size_t data_len);
 
 
-/* Flash erase(sectors) operation, support all possible erase commands */
-int spi_flash_cmd_erase_ops(struct spi_flash *flash, u32 offset, size_t len);
-
 /* Get software write-protect value (BP bits) */
 int spi_flash_cmd_get_sw_write_prot(struct spi_flash *flash);
 
-/* Lock stmicro spi flash region */
-int stm_lock(struct spi_flash *flash, u32 ofs, size_t len);
-
-/* Unlock stmicro spi flash region */
-int stm_unlock(struct spi_flash *flash, u32 ofs, size_t len);
-
-/* Check if a stmicro spi flash region is completely locked */
-int stm_is_locked(struct spi_flash *flash, u32 ofs, size_t len);
-
-/* Enable writing on the SPI flash */
-static inline int spi_flash_cmd_write_enable(struct spi_flash *flash)
-{
-	return spi_flash_cmd(flash->spi, CMD_WRITE_ENABLE, NULL, 0);
-}
-
-/* Disable writing on the SPI flash */
-static inline int spi_flash_cmd_write_disable(struct spi_flash *flash)
-{
-	return spi_flash_cmd(flash->spi, CMD_WRITE_DISABLE, NULL, 0);
-}
-
-/*
- * Used for spi_flash write operation
- * - SPI claim
- * - spi_flash_cmd_write_enable
- * - spi_flash_cmd_write
- * - spi_flash_wait_till_ready
- * - SPI release
- */
-int spi_flash_write_common(struct spi_flash *flash, const u8 *cmd,
-		size_t cmd_len, const void *buf, size_t buf_len);
-
-/*
- * Flash write operation, support all possible write commands.
- * Write the requested data out breaking it up into multiple write
- * commands as needed per the write size.
- */
-int spi_flash_cmd_write_ops(struct spi_flash *flash, u32 offset,
-		size_t len, const void *buf);
-
-/*
- * Same as spi_flash_cmd_read() except it also claims/releases the SPI
- * bus. Used as common part of the ->read() operation.
- */
-int spi_flash_read_common(struct spi_flash *flash, const u8 *cmd,
-		size_t cmd_len, void *data, size_t data_len);
-
-/* Flash read operation, support all possible read commands */
-int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset,
-		size_t len, void *data);
 
 #ifdef CONFIG_SPI_FLASH_MTD
 int spi_flash_mtd_register(struct spi_flash *flash);
 void spi_flash_mtd_unregister(void);
 #endif
-
-/**
- * spi_flash_scan - scan the SPI FLASH
- * @flash:	the spi flash structure
- *
- * The drivers can use this fuction to scan the SPI FLASH.
- * In the scanning, it will try to get all the necessary information to
- * fill the spi_flash{}.
- *
- * Return: 0 for success, others for failure.
- */
-int spi_flash_scan(struct spi_flash *flash);
-
 #endif /* _SF_INTERNAL_H_ */
diff --git a/drivers/mtd/spi/sf_probe.c b/drivers/mtd/spi/sf_probe.c
index 00f8558e7019..7f1378f4946d 100644
--- a/drivers/mtd/spi/sf_probe.c
+++ b/drivers/mtd/spi/sf_probe.c
@@ -40,7 +40,7 @@ static int spi_flash_probe_slave(struct spi_flash *flash)
 		return ret;
 	}
 
-	ret = spi_flash_scan(flash);
+	ret = spi_nor_scan(flash);
 	if (ret)
 		goto err_read_id;
 
@@ -96,32 +96,38 @@ static int spi_flash_std_read(struct udevice *dev, u32 offset, size_t len,
 			      void *buf)
 {
 	struct spi_flash *flash = dev_get_uclass_priv(dev);
+	struct mtd_info *mtd = &flash->mtd;
+	size_t retlen;
 
-	return log_ret(spi_flash_cmd_read_ops(flash, offset, len, buf));
+	return log_ret(mtd->_read(mtd, offset, len, &retlen, buf));
 }
 
 static int spi_flash_std_write(struct udevice *dev, u32 offset, size_t len,
 			       const void *buf)
 {
 	struct spi_flash *flash = dev_get_uclass_priv(dev);
+	struct mtd_info *mtd = &flash->mtd;
+	size_t retlen;
 
-#if defined(CONFIG_SPI_FLASH_SST)
-	if (flash->flags & SNOR_F_SST_WR) {
-		if (flash->spi->mode & SPI_TX_BYTE)
-			return sst_write_bp(flash, offset, len, buf);
-		else
-			return sst_write_wp(flash, offset, len, buf);
-	}
-#endif
-
-	return spi_flash_cmd_write_ops(flash, offset, len, buf);
+	return mtd->_write(mtd, offset, len, &retlen, buf);
 }
 
 static int spi_flash_std_erase(struct udevice *dev, u32 offset, size_t len)
 {
 	struct spi_flash *flash = dev_get_uclass_priv(dev);
+	struct mtd_info *mtd = &flash->mtd;
+	struct erase_info instr;
+
+	if (offset % mtd->erasesize || len % mtd->erasesize) {
+		printf("SF: Erase offset/length not multiple of erase size\n");
+		return -EINVAL;
+	}
+
+	memset(&instr, 0, sizeof(instr));
+	instr.addr = offset;
+	instr.len = len;
 
-	return spi_flash_cmd_erase_ops(flash, offset, len);
+	return mtd->_erase(mtd, &instr);
 }
 
 static int spi_flash_std_get_sw_write_prot(struct udevice *dev)
@@ -161,6 +167,7 @@ static const struct dm_spi_flash_ops spi_flash_std_ops = {
 
 static const struct udevice_id spi_flash_std_ids[] = {
 	{ .compatible = "spi-flash" },
+	{ .compatible = "jedec,spi-nor" },
 	{ }
 };
 
diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c
index 597898d3b4af..c2e5f9320b95 100644
--- a/drivers/mtd/spi/spi-nor-core.c
+++ b/drivers/mtd/spi/spi-nor-core.c
@@ -21,6 +21,8 @@
 #include <spi-mem.h>
 #include <spi.h>
 
+#include "sf_internal.h"
+
 /* Define max times to check status register before we give up. */
 
 /*
@@ -32,63 +34,6 @@
 
 #define DEFAULT_READY_WAIT_JIFFIES		(40UL * HZ)
 
-#define SPI_NOR_MAX_ID_LEN	6
-#define SPI_NOR_MAX_ADDR_WIDTH	4
-
-struct flash_info {
-	char		*name;
-
-	/*
-	 * This array stores the ID bytes.
-	 * The first three bytes are the JEDIC ID.
-	 * JEDEC ID zero means "no ID" (mostly older chips).
-	 */
-	u8		id[SPI_NOR_MAX_ID_LEN];
-	u8		id_len;
-
-	/* The size listed here is what works with SPINOR_OP_SE, which isn't
-	 * necessarily called a "sector" by the vendor.
-	 */
-	unsigned int	sector_size;
-	u16		n_sectors;
-
-	u16		page_size;
-	u16		addr_width;
-
-	u16		flags;
-#define SECT_4K			BIT(0)	/* SPINOR_OP_BE_4K works uniformly */
-#define SPI_NOR_NO_ERASE	BIT(1)	/* No erase command needed */
-#define SST_WRITE		BIT(2)	/* use SST byte programming */
-#define SPI_NOR_NO_FR		BIT(3)	/* Can't do fastread */
-#define SECT_4K_PMC		BIT(4)	/* SPINOR_OP_BE_4K_PMC works uniformly */
-#define SPI_NOR_DUAL_READ	BIT(5)	/* Flash supports Dual Read */
-#define SPI_NOR_QUAD_READ	BIT(6)	/* Flash supports Quad Read */
-#define USE_FSR			BIT(7)	/* use flag status register */
-#define SPI_NOR_HAS_LOCK	BIT(8)	/* Flash supports lock/unlock via SR */
-#define SPI_NOR_HAS_TB		BIT(9)	/*
-					 * Flash SR has Top/Bottom (TB) protect
-					 * bit. Must be used with
-					 * SPI_NOR_HAS_LOCK.
-					 */
-#define	SPI_S3AN		BIT(10)	/*
-					 * Xilinx Spartan 3AN In-System Flash
-					 * (MFR cannot be used for probing
-					 * because it has the same value as
-					 * ATMEL flashes)
-					 */
-#define SPI_NOR_4B_OPCODES	BIT(11)	/*
-					 * Use dedicated 4byte address op codes
-					 * to support memory size above 128Mib.
-					 */
-#define NO_CHIP_ERASE		BIT(12) /* Chip does not support chip erase */
-#define SPI_NOR_SKIP_SFDP	BIT(13)	/* Skip parsing of SFDP tables */
-#define USE_CLSR		BIT(14)	/* use CLSR command */
-
-	int	(*quad_enable)(struct spi_nor *nor);
-};
-
-#define JEDEC_MFR(info)	((info)->id[0])
-
 static int spi_nor_read_write_reg(struct spi_nor *nor, struct spi_mem_op
 		*op, void *buf)
 {
@@ -291,6 +236,7 @@ static struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
 	return mtd->priv;
 }
 
+#ifndef CONFIG_SPI_FLASH_BAR
 static u8 spi_nor_convert_opcode(u8 opcode, const u8 table[][2], size_t size)
 {
 	size_t i;
@@ -365,6 +311,7 @@ static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
 	nor->program_opcode = spi_nor_convert_3to4_program(nor->program_opcode);
 	nor->erase_opcode = spi_nor_convert_3to4_erase(nor->erase_opcode);
 }
+#endif /* !CONFIG_SPI_FLASH_BAR */
 
 /* Enable/disable 4-byte addressing mode. */
 static int set_4byte(struct spi_nor *nor, const struct flash_info *info,
@@ -501,6 +448,79 @@ static int spi_nor_wait_till_ready(struct spi_nor *nor)
 						    DEFAULT_READY_WAIT_JIFFIES);
 }
 
+#ifdef CONFIG_SPI_FLASH_BAR
+/*
+ * This "clean_bar" is necessary in a situation when one was accessing
+ * spi flash memory > 16 MiB by using Bank Address Register's BA24 bit.
+ *
+ * After it the BA24 bit shall be cleared to allow access to correct
+ * memory region after SW reset (by calling "reset" command).
+ *
+ * Otherwise, the BA24 bit may be left set and then after reset, the
+ * ROM would read/write/erase SPL from 16 MiB * bank_sel address.
+ */
+static int clean_bar(struct spi_nor *nor)
+{
+	u8 cmd, bank_sel = 0;
+
+	if (nor->bank_curr == 0)
+		return 0;
+	cmd = nor->bank_write_cmd;
+	nor->bank_curr = 0;
+	write_enable(nor);
+
+	return nor->write_reg(nor, cmd, &bank_sel, 1);
+}
+
+static int write_bar(struct spi_nor *nor, u32 offset)
+{
+	u8 cmd, bank_sel;
+	int ret;
+
+	bank_sel = offset / SZ_16M;
+	if (bank_sel == nor->bank_curr)
+		goto bar_end;
+
+	cmd = nor->bank_write_cmd;
+	write_enable(nor);
+	ret = nor->write_reg(nor, cmd, &bank_sel, 1);
+	if (ret < 0) {
+		debug("SF: fail to write bank register\n");
+		return ret;
+	}
+
+bar_end:
+	nor->bank_curr = bank_sel;
+	return nor->bank_curr;
+}
+
+static int read_bar(struct spi_nor *nor, const struct flash_info *info)
+{
+	u8 curr_bank = 0;
+	int ret;
+
+	switch (JEDEC_MFR(info)) {
+	case SNOR_MFR_SPANSION:
+		nor->bank_read_cmd = SPINOR_OP_BRRD;
+		nor->bank_write_cmd = SPINOR_OP_BRWR;
+		break;
+	default:
+		nor->bank_read_cmd = SPINOR_OP_RDEAR;
+		nor->bank_write_cmd = SPINOR_OP_WREAR;
+	}
+
+	ret = nor->read_reg(nor, nor->bank_read_cmd,
+				    &curr_bank, 1);
+	if (ret) {
+		debug("SF: fail to read bank addr register\n");
+		return ret;
+	}
+	nor->bank_curr = curr_bank;
+
+	return 0;
+}
+#endif
+
 /*
  * Initiate the erasure of a single sector
  */
@@ -545,6 +565,11 @@ static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
 	len = instr->len;
 
 	while (len) {
+#ifdef CONFIG_SPI_FLASH_BAR
+		ret = write_bar(nor, addr);
+		if (ret < 0)
+			return ret;
+#endif
 		write_enable(nor);
 
 		ret = spi_nor_erase_sector(nor, addr);
@@ -559,9 +584,12 @@ static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
 			goto erase_err;
 	}
 
+erase_err:
+#ifdef CONFIG_SPI_FLASH_BAR
+	ret = clean_bar(nor);
+#endif
 	write_disable(nor);
 
-erase_err:
 	return ret;
 }
 
@@ -1140,14 +1168,33 @@ static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
 			size_t *retlen, u_char *buf)
 {
 	struct spi_nor *nor = mtd_to_spi_nor(mtd);
+	struct spi_slave *spi = nor->spi;
 	int ret;
 
 	dev_dbg(nor->dev, "from 0x%08x, len %zd\n", (u32)from, len);
 
 	while (len) {
 		loff_t addr = from;
+		size_t read_len = len;
+
+#ifdef CONFIG_SPI_FLASH_BAR
+		u32 remain_len;
+
+		ret = write_bar(nor, addr);
+		if (ret < 0)
+			return log_ret(ret);
+		remain_len = (SZ_16M * (nor->bank_curr + 1)) - addr;
+
+		if (len < remain_len)
+			read_len = len;
+		else
+			read_len = remain_len;
+#endif
+
+		if (spi->max_read_size)
+			read_len = min(read_len, (size_t)spi->max_read_size);
 
-		ret = nor->read(nor, addr, len, buf);
+		ret = nor->read(nor, addr, read_len, buf);
 		if (ret == 0) {
 			/* We shouldn't see 0-length reads */
 			ret = -EIO;
@@ -1164,18 +1211,49 @@ static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
 	ret = 0;
 
 read_err:
+#ifdef CONFIG_SPI_FLASH_BAR
+	ret = clean_bar(nor);
+#endif
 	return ret;
 }
 
 #ifdef CONFIG_SPI_FLASH_SST
+static int sst_write_byteprogram(struct spi_nor *nor, loff_t to, size_t len,
+				 size_t *retlen, const u_char *buf)
+{
+	size_t actual;
+	int ret = 0;
+
+	for (actual = 0; actual < len; actual++) {
+		nor->program_opcode = SPINOR_OP_BP;
+
+		write_enable(nor);
+		/* write one byte. */
+		ret = nor->write(nor, to, 1, buf + actual);
+		if (ret < 0)
+			goto sst_write_err;
+		ret = spi_nor_wait_till_ready(nor);
+		if (ret)
+			goto sst_write_err;
+		to++;
+	}
+
+sst_write_err:
+	write_disable(nor);
+	return ret;
+}
+
 static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
 		     size_t *retlen, const u_char *buf)
 {
 	struct spi_nor *nor = mtd_to_spi_nor(mtd);
+	struct spi_slave *spi = nor->spi;
 	size_t actual;
 	int ret;
 
 	dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+	if (spi->mode & SPI_TX_BYTE)
+		return sst_write_byteprogram(nor, to, len, retlen, buf);
 
 	write_enable(nor);
 
@@ -1245,6 +1323,7 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
 	size_t *retlen, const u_char *buf)
 {
 	struct spi_nor *nor = mtd_to_spi_nor(mtd);
+	struct spi_slave *spi = nor->spi;
 	size_t page_offset, page_remain, i;
 	ssize_t ret;
 
@@ -1273,6 +1352,16 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
 		page_remain = min_t(size_t,
 				    nor->page_size - page_offset, len - i);
 
+		if (spi->max_write_size)
+			page_remain = min(page_remain,
+					  (size_t)(spi->max_write_size -
+					  (nor->addr_width + 1)));
+
+#ifdef CONFIG_SPI_FLASH_BAR
+		ret = write_bar(nor, addr);
+		if (ret < 0)
+			return ret;
+#endif
 		write_enable(nor);
 		ret = nor->write(nor, addr, page_remain, buf + i);
 		if (ret < 0)
@@ -1291,6 +1380,9 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
 	}
 
 write_err:
+#ifdef CONFIG_SPI_FLASH_BAR
+	ret = clean_bar(nor);
+#endif
 	return ret;
 }
 
@@ -2534,12 +2626,20 @@ int spi_nor_scan(struct spi_nor *nor)
 		/* already configured from SFDP */
 	} else if (info->addr_width) {
 		nor->addr_width = info->addr_width;
-	} else if (mtd->size > 0x1000000) {
+	} else if (mtd->size > SZ_16M) {
+#ifndef CONFIG_SPI_FLASH_BAR
 		/* enable 4-byte addressing if the device exceeds 16MiB */
 		nor->addr_width = 4;
 		if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
 		    info->flags & SPI_NOR_4B_OPCODES)
 			spi_nor_set_4byte_opcodes(nor, info);
+#else
+	/* Configure the BAR - discover bank cmds and read current bank */
+	nor->addr_width = 3;
+	ret = read_bar(nor, info);
+	if (ret < 0)
+		return ret;
+#endif
 	} else {
 		nor->addr_width = 3;
 	}
diff --git a/drivers/spi/stm32_qspi.c b/drivers/spi/stm32_qspi.c
index 3b92254a5ce1..8b60d7c3b224 100644
--- a/drivers/spi/stm32_qspi.c
+++ b/drivers/spi/stm32_qspi.c
@@ -271,9 +271,9 @@ static void _stm32_qspi_enable_mmap(struct stm32_qspi_priv *priv,
 {
 	unsigned int ccr_reg;
 
-	priv->command = flash->read_cmd | CMD_HAS_ADR | CMD_HAS_DATA
+	priv->command = flash->read_opcode | CMD_HAS_ADR | CMD_HAS_DATA
 			| CMD_HAS_DUMMY;
-	priv->dummycycles = flash->dummy_byte * 8;
+	priv->dummycycles = flash->read_dummy;
 
 	ccr_reg = _stm32_qspi_gen_ccr(priv, STM32_QSPI_CCR_MEM_MAP);
 
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 507458a76076..88e80af57941 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -105,6 +105,7 @@
 
 /* Used for Spansion flashes only. */
 #define SPINOR_OP_BRWR		0x17	/* Bank register write */
+#define SPINOR_OP_BRRD		0x16	/* Bank register read */
 #define SPINOR_OP_CLSR		0x30	/* Clear status register 1 */
 
 /* Used for Micron flashes only. */
@@ -256,6 +257,9 @@ struct flash_info;
  * @read_opcode:	the read opcode
  * @read_dummy:		the dummy needed by the read operation
  * @program_opcode:	the program opcode
+ * @bank_read_cmd:	Bank read cmd
+ * @bank_write_cmd:	Bank write cmd
+ * @bank_curr:		Current flash bank
  * @sst_write_second:	used by the SST write operation
  * @flags:		flag options for the current SPI-NOR (SNOR_F_*)
  * @read_proto:		the SPI protocol for read operations
@@ -291,6 +295,11 @@ struct spi_nor {
 	u8			read_opcode;
 	u8			read_dummy;
 	u8			program_opcode;
+#ifdef CONFIG_SPI_FLASH_BAR
+	u8			bank_read_cmd;
+	u8			bank_write_cmd;
+	u8			bank_curr;
+#endif
 	enum spi_nor_protocol	read_proto;
 	enum spi_nor_protocol	write_proto;
 	enum spi_nor_protocol	reg_proto;
diff --git a/include/spi_flash.h b/include/spi_flash.h
index e427e960d54f..7f691e8559cd 100644
--- a/include/spi_flash.h
+++ b/include/spi_flash.h
@@ -11,6 +11,7 @@
 
 #include <dm.h>	/* Because we dereference struct udevice here */
 #include <linux/types.h>
+#include <linux/mtd/spi-nor.h>
 
 #ifndef CONFIG_SF_DEFAULT_SPEED
 # define CONFIG_SF_DEFAULT_SPEED	1000000
@@ -27,86 +28,6 @@
 
 struct spi_slave;
 
-/**
- * struct spi_flash - SPI flash structure
- *
- * @spi:		SPI slave
- * @dev:		SPI flash device
- * @name:		Name of SPI flash
- * @dual_flash:		Indicates dual flash memories - dual stacked, parallel
- * @shift:		Flash shift useful in dual parallel
- * @flags:		Indication of spi flash flags
- * @size:		Total flash size
- * @page_size:		Write (page) size
- * @sector_size:	Sector size
- * @erase_size:		Erase size
- * @bank_read_cmd:	Bank read cmd
- * @bank_write_cmd:	Bank write cmd
- * @bank_curr:		Current flash bank
- * @erase_cmd:		Erase cmd 4K, 32K, 64K
- * @read_cmd:		Read cmd - Array Fast, Extn read and quad read.
- * @write_cmd:		Write cmd - page and quad program.
- * @dummy_byte:		Dummy cycles for read operation.
- * @memory_map:		Address of read-only SPI flash access
- * @flash_lock:		lock a region of the SPI Flash
- * @flash_unlock:	unlock a region of the SPI Flash
- * @flash_is_locked:	check if a region of the SPI Flash is completely locked
- * @read:		Flash read ops: Read len bytes at offset into buf
- *			Supported cmds: Fast Array Read
- * @write:		Flash write ops: Write len bytes from buf into offset
- *			Supported cmds: Page Program
- * @erase:		Flash erase ops: Erase len bytes from offset
- *			Supported cmds: Sector erase 4K, 32K, 64K
- * return 0 - Success, 1 - Failure
- */
-struct spi_flash {
-	struct spi_slave *spi;
-#ifdef CONFIG_DM_SPI_FLASH
-	struct udevice *dev;
-#endif
-	const char *name;
-	u8 dual_flash;
-	u8 shift;
-	u16 flags;
-
-	u32 size;
-	u32 page_size;
-	u32 sector_size;
-	u32 erase_size;
-#ifdef CONFIG_SPI_FLASH_BAR
-	u8 bank_read_cmd;
-	u8 bank_write_cmd;
-	u8 bank_curr;
-#endif
-	u8 erase_cmd;
-	u8 read_cmd;
-	u8 write_cmd;
-	u8 dummy_byte;
-
-	void *memory_map;
-
-	int (*flash_lock)(struct spi_flash *flash, u32 ofs, size_t len);
-	int (*flash_unlock)(struct spi_flash *flash, u32 ofs, size_t len);
-	int (*flash_is_locked)(struct spi_flash *flash, u32 ofs, size_t len);
-#ifndef CONFIG_DM_SPI_FLASH
-	/*
-	 * These are not strictly needed for driver model, but keep them here
-	 * while the transition is in progress.
-	 *
-	 * Normally each driver would provide its own operations, but for
-	 * SPI flash most chips use the same algorithms. One approach is
-	 * to create a 'common' SPI flash device which knows how to talk
-	 * to most devices, and then allow other drivers to be used instead
-	 * if required, perhaps with a way of scanning through the list to
-	 * find the driver that matches the device.
-	 */
-	int (*read)(struct spi_flash *flash, u32 offset, size_t len, void *buf);
-	int (*write)(struct spi_flash *flash, u32 offset, size_t len,
-			const void *buf);
-	int (*erase)(struct spi_flash *flash, u32 offset, size_t len);
-#endif
-};
-
 struct dm_spi_flash_ops {
 	int (*read)(struct udevice *dev, u32 offset, size_t len, void *buf);
 	int (*write)(struct udevice *dev, u32 offset, size_t len,
@@ -225,19 +146,37 @@ void spi_flash_free(struct spi_flash *flash);
 static inline int spi_flash_read(struct spi_flash *flash, u32 offset,
 		size_t len, void *buf)
 {
-	return flash->read(flash, offset, len, buf);
+	struct mtd_info *mtd = &flash->mtd;
+	size_t retlen;
+
+	return mtd->_read(mtd, offset, len, &retlen, buf);
 }
 
 static inline int spi_flash_write(struct spi_flash *flash, u32 offset,
 		size_t len, const void *buf)
 {
-	return flash->write(flash, offset, len, buf);
+	struct mtd_info *mtd = &flash->mtd;
+	size_t retlen;
+
+	return mtd->_write(mtd, offset, len, &retlen, buf);
 }
 
 static inline int spi_flash_erase(struct spi_flash *flash, u32 offset,
 		size_t len)
 {
-	return flash->erase(flash, offset, len);
+	struct mtd_info *mtd = &flash->mtd;
+	struct erase_info instr;
+
+	if (offset % mtd->erasesize || len % mtd->erasesize) {
+		printf("SF: Erase offset/length not multiple of erase size\n");
+		return -EINVAL;
+	}
+
+	memset(&instr, 0, sizeof(instr));
+	instr.addr = offset;
+	instr.len = len;
+
+	return mtd->_erase(mtd, &instr);
 }
 #endif
 
-- 
2.20.1