[PATCH v7 00/11] Add initial RDA8810PL SoC and Orange Pi boards support

All of lore.kernel.org
 help / color / mirror / Atom feed

* [PATCH v7 00/11] Add initial RDA8810PL SoC and Orange Pi boards support
@ 2018-12-18 15:02 ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

Hello Maintainers,

This patch series adds initial RDA8810PL SoC and Orange Pi boards (2G IoT and
i96) support. RDA8810PL is an ARM Cortex A5 based SoC with Vivante's GC860
GPU. The SoC has been added as a new ARM sub architecture with myself as the
maintainer.

More information about the boards can be found in below links:

1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/

All patches are reviewed by the corresponding subsystem maintainers. The
clocksource and irqchip patches are reviewed and merged while the serial
driver got review from Greg but I'm not sure who will apply it.

So as per my discussion with Arnd, sending the individual patches instead
of a Pull request so that the rest of the patches can go through the
ARM SoC tree.

Please consider applying it.

Thanks,
Mani

Andreas Färber (4):
  dt-bindings: Add RDA Micro vendor prefix
  dt-bindings: arm: Document RDA8810PL and reference boards
  ARM: Prepare RDA8810PL SoC
  dt-bindings: serial: Document RDA Micro UART

Manivannan Sadhasivam (7):
  ARM: dts: Add devicetree for RDA8810PL SoC
  ARM: dts: Add devicetree for OrangePi 2G IoT board
  ARM: dts: Add devicetree for OrangePi i96 board
  ARM: dts: rda8810pl: Add timer support
  ARM: dts: rda8810pl: Add interrupt support for UART
  tty: serial: Add RDA8810PL UART driver
  MAINTAINERS: Add entry for RDA Micro SoC architecture

 .../admin-guide/kernel-parameters.txt         |   6 +
 Documentation/devicetree/bindings/arm/rda.txt |  17 +
 .../bindings/serial/rda,8810pl-uart.txt       |  17 +
 .../devicetree/bindings/vendor-prefixes.txt   |   1 +
 MAINTAINERS                                   |  14 +
 arch/arm/Kconfig                              |   2 +
 arch/arm/Makefile                             |   1 +
 arch/arm/boot/dts/Makefile                    |   3 +
 .../boot/dts/rda8810pl-orangepi-2g-iot.dts    |  50 ++
 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts  |  50 ++
 arch/arm/boot/dts/rda8810pl.dtsi              |  99 +++
 arch/arm/mach-rda/Kconfig                     |   7 +
 arch/arm/mach-rda/Makefile                    |   1 +
 drivers/tty/serial/Kconfig                    |  19 +
 drivers/tty/serial/Makefile                   |   1 +
 drivers/tty/serial/rda-uart.c                 | 831 ++++++++++++++++++
 include/uapi/linux/serial_core.h              |   3 +
 17 files changed, 1122 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/rda.txt
 create mode 100644 Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts
 create mode 100644 arch/arm/boot/dts/rda8810pl.dtsi
 create mode 100644 arch/arm/mach-rda/Kconfig
 create mode 100644 arch/arm/mach-rda/Makefile
 create mode 100644 drivers/tty/serial/rda-uart.c

-- 
2.17.1


^ permalink raw reply	[flat|nested] 29+ messages in thread

* [PATCH v7 00/11] Add initial RDA8810PL SoC and Orange Pi boards support
@ 2018-12-18 15:02 ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

Hello Maintainers,

This patch series adds initial RDA8810PL SoC and Orange Pi boards (2G IoT and
i96) support. RDA8810PL is an ARM Cortex A5 based SoC with Vivante's GC860
GPU. The SoC has been added as a new ARM sub architecture with myself as the
maintainer.

More information about the boards can be found in below links:

1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/

All patches are reviewed by the corresponding subsystem maintainers. The
clocksource and irqchip patches are reviewed and merged while the serial
driver got review from Greg but I'm not sure who will apply it.

So as per my discussion with Arnd, sending the individual patches instead
of a Pull request so that the rest of the patches can go through the
ARM SoC tree.

Please consider applying it.

Thanks,
Mani

Andreas Färber (4):
  dt-bindings: Add RDA Micro vendor prefix
  dt-bindings: arm: Document RDA8810PL and reference boards
  ARM: Prepare RDA8810PL SoC
  dt-bindings: serial: Document RDA Micro UART

Manivannan Sadhasivam (7):
  ARM: dts: Add devicetree for RDA8810PL SoC
  ARM: dts: Add devicetree for OrangePi 2G IoT board
  ARM: dts: Add devicetree for OrangePi i96 board
  ARM: dts: rda8810pl: Add timer support
  ARM: dts: rda8810pl: Add interrupt support for UART
  tty: serial: Add RDA8810PL UART driver
  MAINTAINERS: Add entry for RDA Micro SoC architecture

 .../admin-guide/kernel-parameters.txt         |   6 +
 Documentation/devicetree/bindings/arm/rda.txt |  17 +
 .../bindings/serial/rda,8810pl-uart.txt       |  17 +
 .../devicetree/bindings/vendor-prefixes.txt   |   1 +
 MAINTAINERS                                   |  14 +
 arch/arm/Kconfig                              |   2 +
 arch/arm/Makefile                             |   1 +
 arch/arm/boot/dts/Makefile                    |   3 +
 .../boot/dts/rda8810pl-orangepi-2g-iot.dts    |  50 ++
 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts  |  50 ++
 arch/arm/boot/dts/rda8810pl.dtsi              |  99 +++
 arch/arm/mach-rda/Kconfig                     |   7 +
 arch/arm/mach-rda/Makefile                    |   1 +
 drivers/tty/serial/Kconfig                    |  19 +
 drivers/tty/serial/Makefile                   |   1 +
 drivers/tty/serial/rda-uart.c                 | 831 ++++++++++++++++++
 include/uapi/linux/serial_core.h              |   3 +
 17 files changed, 1122 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/rda.txt
 create mode 100644 Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts
 create mode 100644 arch/arm/boot/dts/rda8810pl.dtsi
 create mode 100644 arch/arm/mach-rda/Kconfig
 create mode 100644 arch/arm/mach-rda/Makefile
 create mode 100644 drivers/tty/serial/rda-uart.c

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 29+ messages in thread

* [PATCH v7 01/11] dt-bindings: Add RDA Micro vendor prefix
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

From: Andreas Färber <afaerber@suse.de>

Add vendor prefix for RDA Micro which now merged into Unisoc
Communications Inc.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 4b1a2a8fcc16..37826fac7684 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -320,6 +320,7 @@ ralink	Mediatek/Ralink Technology Corp.
 ramtron	Ramtron International
 raspberrypi	Raspberry Pi Foundation
 raydium	Raydium Semiconductor Corp.
+rda	Unisoc Communications, Inc.
 realtek Realtek Semiconductor Corp.
 renesas	Renesas Electronics Corporation
 richtek	Richtek Technology Corporation
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 01/11] dt-bindings: Add RDA Micro vendor prefix
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

From: Andreas Färber <afaerber@suse.de>

Add vendor prefix for RDA Micro which now merged into Unisoc
Communications Inc.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 4b1a2a8fcc16..37826fac7684 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -320,6 +320,7 @@ ralink	Mediatek/Ralink Technology Corp.
 ramtron	Ramtron International
 raspberrypi	Raspberry Pi Foundation
 raydium	Raydium Semiconductor Corp.
+rda	Unisoc Communications, Inc.
 realtek Realtek Semiconductor Corp.
 renesas	Renesas Electronics Corporation
 richtek	Richtek Technology Corporation
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 02/11] dt-bindings: arm: Document RDA8810PL and reference boards
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

From: Andreas Färber <afaerber@suse.de>

Add bindings for RDA Micro RDA8810PL SoC and below reference boards:

1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/

Cc: zhao_steven@263.net
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 Documentation/devicetree/bindings/arm/rda.txt | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/rda.txt

diff --git a/Documentation/devicetree/bindings/arm/rda.txt b/Documentation/devicetree/bindings/arm/rda.txt
new file mode 100644
index 000000000000..43c80762c428
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/rda.txt
@@ -0,0 +1,17 @@
+RDA Micro platforms device tree bindings
+----------------------------------------
+
+RDA8810PL SoC
+=============
+
+Required root node properties:
+
+ - compatible :  must contain "rda,8810pl"
+
+
+Boards:
+
+Root node property compatible must contain, depending on board:
+
+ - Orange Pi 2G-IoT: "xunlong,orangepi-2g-iot"
+ - Orange Pi i96: "xunlong,orangepi-i96"
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 02/11] dt-bindings: arm: Document RDA8810PL and reference boards
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

From: Andreas Färber <afaerber@suse.de>

Add bindings for RDA Micro RDA8810PL SoC and below reference boards:

1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/

Cc: zhao_steven@263.net
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 Documentation/devicetree/bindings/arm/rda.txt | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/rda.txt

diff --git a/Documentation/devicetree/bindings/arm/rda.txt b/Documentation/devicetree/bindings/arm/rda.txt
new file mode 100644
index 000000000000..43c80762c428
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/rda.txt
@@ -0,0 +1,17 @@
+RDA Micro platforms device tree bindings
+----------------------------------------
+
+RDA8810PL SoC
+=============
+
+Required root node properties:
+
+ - compatible :  must contain "rda,8810pl"
+
+
+Boards:
+
+Root node property compatible must contain, depending on board:
+
+ - Orange Pi 2G-IoT: "xunlong,orangepi-2g-iot"
+ - Orange Pi i96: "xunlong,orangepi-i96"
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 03/11] ARM: Prepare RDA8810PL SoC
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

From: Andreas Färber <afaerber@suse.de>

Introduce ARCH_RDA and mach-rda for RDA Micro SoCs.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/Kconfig           | 2 ++
 arch/arm/Makefile          | 1 +
 arch/arm/mach-rda/Kconfig  | 7 +++++++
 arch/arm/mach-rda/Makefile | 1 +
 4 files changed, 11 insertions(+)
 create mode 100644 arch/arm/mach-rda/Kconfig
 create mode 100644 arch/arm/mach-rda/Makefile

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 91be74d8df65..084f0983e6b2 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -804,6 +804,8 @@ source "arch/arm/plat-pxa/Kconfig"
 
 source "arch/arm/mach-qcom/Kconfig"
 
+source "arch/arm/mach-rda/Kconfig"
+
 source "arch/arm/mach-realview/Kconfig"
 
 source "arch/arm/mach-rockchip/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 05a91d8b89f3..10056ccdb8be 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -202,6 +202,7 @@ machine-$(CONFIG_ARCH_ORION5X)		+= orion5x
 machine-$(CONFIG_ARCH_PICOXCELL)	+= picoxcell
 machine-$(CONFIG_ARCH_PXA)		+= pxa
 machine-$(CONFIG_ARCH_QCOM)		+= qcom
+machine-$(CONFIG_ARCH_RDA)		+= rda
 machine-$(CONFIG_ARCH_REALVIEW)		+= realview
 machine-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip
 machine-$(CONFIG_ARCH_RPC)		+= rpc
diff --git a/arch/arm/mach-rda/Kconfig b/arch/arm/mach-rda/Kconfig
new file mode 100644
index 000000000000..4df8b8ee1a9d
--- /dev/null
+++ b/arch/arm/mach-rda/Kconfig
@@ -0,0 +1,7 @@
+menuconfig ARCH_RDA
+	bool "RDA Micro SoCs"
+	depends on ARCH_MULTI_V7
+	select RDA_INTC
+	select RDA_TIMER
+	help
+	  This enables support for the RDA Micro 8810PL SoC family.
diff --git a/arch/arm/mach-rda/Makefile b/arch/arm/mach-rda/Makefile
new file mode 100644
index 000000000000..6bea3d3a2dd7
--- /dev/null
+++ b/arch/arm/mach-rda/Makefile
@@ -0,0 +1 @@
+obj- += dummy.o
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 03/11] ARM: Prepare RDA8810PL SoC
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

From: Andreas Färber <afaerber@suse.de>

Introduce ARCH_RDA and mach-rda for RDA Micro SoCs.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/Kconfig           | 2 ++
 arch/arm/Makefile          | 1 +
 arch/arm/mach-rda/Kconfig  | 7 +++++++
 arch/arm/mach-rda/Makefile | 1 +
 4 files changed, 11 insertions(+)
 create mode 100644 arch/arm/mach-rda/Kconfig
 create mode 100644 arch/arm/mach-rda/Makefile

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 91be74d8df65..084f0983e6b2 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -804,6 +804,8 @@ source "arch/arm/plat-pxa/Kconfig"
 
 source "arch/arm/mach-qcom/Kconfig"
 
+source "arch/arm/mach-rda/Kconfig"
+
 source "arch/arm/mach-realview/Kconfig"
 
 source "arch/arm/mach-rockchip/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 05a91d8b89f3..10056ccdb8be 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -202,6 +202,7 @@ machine-$(CONFIG_ARCH_ORION5X)		+= orion5x
 machine-$(CONFIG_ARCH_PICOXCELL)	+= picoxcell
 machine-$(CONFIG_ARCH_PXA)		+= pxa
 machine-$(CONFIG_ARCH_QCOM)		+= qcom
+machine-$(CONFIG_ARCH_RDA)		+= rda
 machine-$(CONFIG_ARCH_REALVIEW)		+= realview
 machine-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip
 machine-$(CONFIG_ARCH_RPC)		+= rpc
diff --git a/arch/arm/mach-rda/Kconfig b/arch/arm/mach-rda/Kconfig
new file mode 100644
index 000000000000..4df8b8ee1a9d
--- /dev/null
+++ b/arch/arm/mach-rda/Kconfig
@@ -0,0 +1,7 @@
+menuconfig ARCH_RDA
+	bool "RDA Micro SoCs"
+	depends on ARCH_MULTI_V7
+	select RDA_INTC
+	select RDA_TIMER
+	help
+	  This enables support for the RDA Micro 8810PL SoC family.
diff --git a/arch/arm/mach-rda/Makefile b/arch/arm/mach-rda/Makefile
new file mode 100644
index 000000000000..6bea3d3a2dd7
--- /dev/null
+++ b/arch/arm/mach-rda/Makefile
@@ -0,0 +1 @@
+obj- += dummy.o
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 04/11] ARM: dts: Add devicetree for RDA8810PL SoC
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

Add initial device tree for RDA8810PL SoC from RDA Microelectronics.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/rda8810pl.dtsi | 86 ++++++++++++++++++++++++++++++++
 1 file changed, 86 insertions(+)
 create mode 100644 arch/arm/boot/dts/rda8810pl.dtsi

diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/rda8810pl.dtsi
new file mode 100644
index 000000000000..15547b138977
--- /dev/null
+++ b/arch/arm/boot/dts/rda8810pl.dtsi
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * RDA8810PL SoC
+ *
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+/ {
+	compatible = "rda,8810pl";
+	interrupt-parent = <&intc>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a5";
+			reg = <0x0>;
+		};
+	};
+
+	sram@100000 {
+		compatible = "mmio-sram";
+		reg = <0x100000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+	};
+
+	apb@20800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x20800000 0x100000>;
+
+		intc: interrupt-controller@0 {
+			compatible = "rda,8810pl-intc";
+			reg = <0x0 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	apb@20900000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x20900000 0x100000>;
+	};
+
+	apb@20a00000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x20a00000 0x100000>;
+
+		uart1: serial@0 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x0 0x1000>;
+			status = "disabled";
+		};
+
+		uart2: serial@10000 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x10000 0x1000>;
+			status = "disabled";
+		};
+
+		uart3: serial@90000 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x90000 0x1000>;
+			status = "disabled";
+		};
+	};
+
+	l2: cache-controller@21100000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x21100000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+};
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 04/11] ARM: dts: Add devicetree for RDA8810PL SoC
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

Add initial device tree for RDA8810PL SoC from RDA Microelectronics.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/rda8810pl.dtsi | 86 ++++++++++++++++++++++++++++++++
 1 file changed, 86 insertions(+)
 create mode 100644 arch/arm/boot/dts/rda8810pl.dtsi

diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/rda8810pl.dtsi
new file mode 100644
index 000000000000..15547b138977
--- /dev/null
+++ b/arch/arm/boot/dts/rda8810pl.dtsi
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * RDA8810PL SoC
+ *
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+/ {
+	compatible = "rda,8810pl";
+	interrupt-parent = <&intc>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a5";
+			reg = <0x0>;
+		};
+	};
+
+	sram@100000 {
+		compatible = "mmio-sram";
+		reg = <0x100000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+	};
+
+	apb@20800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x20800000 0x100000>;
+
+		intc: interrupt-controller@0 {
+			compatible = "rda,8810pl-intc";
+			reg = <0x0 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	apb@20900000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x20900000 0x100000>;
+	};
+
+	apb@20a00000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x20a00000 0x100000>;
+
+		uart1: serial@0 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x0 0x1000>;
+			status = "disabled";
+		};
+
+		uart2: serial@10000 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x10000 0x1000>;
+			status = "disabled";
+		};
+
+		uart3: serial@90000 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x90000 0x1000>;
+			status = "disabled";
+		};
+	};
+
+	l2: cache-controller@21100000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x21100000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 05/11] ARM: dts: Add devicetree for OrangePi 2G IoT board
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

Add initial devicetree support for OrangePi 2G IoT board from Xunlong.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/Makefile                    |  2 +
 .../boot/dts/rda8810pl-orangepi-2g-iot.dts    | 50 +++++++++++++++++++
 2 files changed, 52 insertions(+)
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b0e966d625b9..a0fdad8f10dd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -806,6 +806,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8974-sony-xperia-castor.dtb \
 	qcom-msm8974-sony-xperia-honami.dtb \
 	qcom-mdm9615-wp8548-mangoh-green.dtb
+dtb-$(CONFIG_ARCH_RDA) += \
+	rda8810pl-orangepi-2g-iot.dtb
 dtb-$(CONFIG_ARCH_REALVIEW) += \
 	arm-realview-pb1176.dtb \
 	arm-realview-pb11mp.dtb \
diff --git a/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts b/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts
new file mode 100644
index 000000000000..98e34248ae80
--- /dev/null
+++ b/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+
+#include "rda8810pl.dtsi"
+
+/ {
+	compatible = "xunlong,orangepi-2g-iot", "rda,8810pl";
+	model = "Orange Pi 2G-IoT";
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial2:921600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	uart_clk: uart-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <921600>;
+		#clock-cells = <0>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart2 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart3 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 05/11] ARM: dts: Add devicetree for OrangePi 2G IoT board
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

Add initial devicetree support for OrangePi 2G IoT board from Xunlong.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/Makefile                    |  2 +
 .../boot/dts/rda8810pl-orangepi-2g-iot.dts    | 50 +++++++++++++++++++
 2 files changed, 52 insertions(+)
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b0e966d625b9..a0fdad8f10dd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -806,6 +806,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8974-sony-xperia-castor.dtb \
 	qcom-msm8974-sony-xperia-honami.dtb \
 	qcom-mdm9615-wp8548-mangoh-green.dtb
+dtb-$(CONFIG_ARCH_RDA) += \
+	rda8810pl-orangepi-2g-iot.dtb
 dtb-$(CONFIG_ARCH_REALVIEW) += \
 	arm-realview-pb1176.dtb \
 	arm-realview-pb11mp.dtb \
diff --git a/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts b/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts
new file mode 100644
index 000000000000..98e34248ae80
--- /dev/null
+++ b/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+
+#include "rda8810pl.dtsi"
+
+/ {
+	compatible = "xunlong,orangepi-2g-iot", "rda,8810pl";
+	model = "Orange Pi 2G-IoT";
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial2:921600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	uart_clk: uart-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <921600>;
+		#clock-cells = <0>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart2 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart3 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 06/11] ARM: dts: Add devicetree for OrangePi i96 board
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

Add initial devicetree for Orange Pi i96 board from Xunlong. It
is one of the 96Boards IoT Edition board.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/Makefile                   |  3 +-
 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts | 50 ++++++++++++++++++++
 2 files changed, 52 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a0fdad8f10dd..cfb08ea33872 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -807,7 +807,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8974-sony-xperia-honami.dtb \
 	qcom-mdm9615-wp8548-mangoh-green.dtb
 dtb-$(CONFIG_ARCH_RDA) += \
-	rda8810pl-orangepi-2g-iot.dtb
+	rda8810pl-orangepi-2g-iot.dtb \
+	rda8810pl-orangepi-i96.dtb
 dtb-$(CONFIG_ARCH_REALVIEW) += \
 	arm-realview-pb1176.dtb \
 	arm-realview-pb11mp.dtb \
diff --git a/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts b/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts
new file mode 100644
index 000000000000..728f76931b99
--- /dev/null
+++ b/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+
+#include "rda8810pl.dtsi"
+
+/ {
+	compatible = "xunlong,orangepi-i96", "rda,8810pl";
+	model = "Orange Pi i96";
+
+	aliases {
+		serial0 = &uart2;
+		serial1 = &uart1;
+		serial2 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial2:921600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	uart_clk: uart-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <921600>;
+		#clock-cells = <0>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart2 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart3 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 06/11] ARM: dts: Add devicetree for OrangePi i96 board
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

Add initial devicetree for Orange Pi i96 board from Xunlong. It
is one of the 96Boards IoT Edition board.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/Makefile                   |  3 +-
 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts | 50 ++++++++++++++++++++
 2 files changed, 52 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/rda8810pl-orangepi-i96.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a0fdad8f10dd..cfb08ea33872 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -807,7 +807,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8974-sony-xperia-honami.dtb \
 	qcom-mdm9615-wp8548-mangoh-green.dtb
 dtb-$(CONFIG_ARCH_RDA) += \
-	rda8810pl-orangepi-2g-iot.dtb
+	rda8810pl-orangepi-2g-iot.dtb \
+	rda8810pl-orangepi-i96.dtb
 dtb-$(CONFIG_ARCH_REALVIEW) += \
 	arm-realview-pb1176.dtb \
 	arm-realview-pb11mp.dtb \
diff --git a/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts b/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts
new file mode 100644
index 000000000000..728f76931b99
--- /dev/null
+++ b/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+
+#include "rda8810pl.dtsi"
+
+/ {
+	compatible = "xunlong,orangepi-i96", "rda,8810pl";
+	model = "Orange Pi i96";
+
+	aliases {
+		serial0 = &uart2;
+		serial1 = &uart1;
+		serial2 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial2:921600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	uart_clk: uart-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <921600>;
+		#clock-cells = <0>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart2 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
+
+&uart3 {
+	status = "okay";
+	clocks = <&uart_clk>;
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 07/11] ARM: dts: rda8810pl: Add timer support
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

Add timer support for RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/rda8810pl.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/rda8810pl.dtsi
index 15547b138977..84baa4c0a14c 100644
--- a/arch/arm/boot/dts/rda8810pl.dtsi
+++ b/arch/arm/boot/dts/rda8810pl.dtsi
@@ -6,6 +6,8 @@
  * Copyright (c) 2018 Manivannan Sadhasivam
  */
 
+#include <dt-bindings/interrupt-controller/irq.h>
+
 / {
 	compatible = "rda,8810pl";
 	interrupt-parent = <&intc>;
@@ -50,6 +52,14 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0 0x20900000 0x100000>;
+
+		timer@10000 {
+			compatible = "rda,8810pl-timer";
+			reg = <0x10000 0x1000>;
+			interrupts = <16 IRQ_TYPE_LEVEL_HIGH>,
+				     <17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hwtimer", "ostimer";
+		};
 	};
 
 	apb@20a00000 {
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 07/11] ARM: dts: rda8810pl: Add timer support
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

Add timer support for RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/rda8810pl.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/rda8810pl.dtsi
index 15547b138977..84baa4c0a14c 100644
--- a/arch/arm/boot/dts/rda8810pl.dtsi
+++ b/arch/arm/boot/dts/rda8810pl.dtsi
@@ -6,6 +6,8 @@
  * Copyright (c) 2018 Manivannan Sadhasivam
  */
 
+#include <dt-bindings/interrupt-controller/irq.h>
+
 / {
 	compatible = "rda,8810pl";
 	interrupt-parent = <&intc>;
@@ -50,6 +52,14 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0 0x20900000 0x100000>;
+
+		timer@10000 {
+			compatible = "rda,8810pl-timer";
+			reg = <0x10000 0x1000>;
+			interrupts = <16 IRQ_TYPE_LEVEL_HIGH>,
+				     <17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hwtimer", "ostimer";
+		};
 	};
 
 	apb@20a00000 {
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 08/11] dt-bindings: serial: Document RDA Micro UART
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

From: Andreas Färber <afaerber@suse.de>

Add an initial binding for the UART in RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 .../bindings/serial/rda,8810pl-uart.txt         | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt

diff --git a/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
new file mode 100644
index 000000000000..a08df97a69e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
@@ -0,0 +1,17 @@
+RDA Micro UART
+
+Required properties:
+- compatible :  "rda,8810pl-uart" for RDA8810PL SoCs.
+- reg        :  Offset and length of the register set for the device.
+- interrupts :  Should contain UART interrupt.
+- clocks     :  Phandle to the input clock.
+
+
+Example:
+
+		uart2: serial@20a90000 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x20a90000 0x1000>;
+			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>;
+		};
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 08/11] dt-bindings: serial: Document RDA Micro UART
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

From: Andreas Färber <afaerber@suse.de>

Add an initial binding for the UART in RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 .../bindings/serial/rda,8810pl-uart.txt         | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt

diff --git a/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
new file mode 100644
index 000000000000..a08df97a69e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
@@ -0,0 +1,17 @@
+RDA Micro UART
+
+Required properties:
+- compatible :  "rda,8810pl-uart" for RDA8810PL SoCs.
+- reg        :  Offset and length of the register set for the device.
+- interrupts :  Should contain UART interrupt.
+- clocks     :  Phandle to the input clock.
+
+
+Example:
+
+		uart2: serial@20a90000 {
+			compatible = "rda,8810pl-uart";
+			reg = <0x20a90000 0x1000>;
+			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>;
+		};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 09/11] ARM: dts: rda8810pl: Add interrupt support for UART
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

Add interrupt support for UART in RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/rda8810pl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/rda8810pl.dtsi
index 84baa4c0a14c..19cde895bf65 100644
--- a/arch/arm/boot/dts/rda8810pl.dtsi
+++ b/arch/arm/boot/dts/rda8810pl.dtsi
@@ -71,18 +71,21 @@
 		uart1: serial@0 {
 			compatible = "rda,8810pl-uart";
 			reg = <0x0 0x1000>;
+			interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
 		uart2: serial@10000 {
 			compatible = "rda,8810pl-uart";
 			reg = <0x10000 0x1000>;
+			interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
 		uart3: serial@90000 {
 			compatible = "rda,8810pl-uart";
 			reg = <0x90000 0x1000>;
+			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 	};
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 09/11] ARM: dts: rda8810pl: Add interrupt support for UART
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

Add interrupt support for UART in RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/rda8810pl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/rda8810pl.dtsi
index 84baa4c0a14c..19cde895bf65 100644
--- a/arch/arm/boot/dts/rda8810pl.dtsi
+++ b/arch/arm/boot/dts/rda8810pl.dtsi
@@ -71,18 +71,21 @@
 		uart1: serial@0 {
 			compatible = "rda,8810pl-uart";
 			reg = <0x0 0x1000>;
+			interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
 		uart2: serial@10000 {
 			compatible = "rda,8810pl-uart";
 			reg = <0x10000 0x1000>;
+			interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
 		uart3: serial@90000 {
 			compatible = "rda,8810pl-uart";
 			reg = <0x90000 0x1000>;
+			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 	};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 10/11] tty: serial: Add RDA8810PL UART driver
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

Add UART driver for RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 .../admin-guide/kernel-parameters.txt         |   6 +
 drivers/tty/serial/Kconfig                    |  19 +
 drivers/tty/serial/Makefile                   |   1 +
 drivers/tty/serial/rda-uart.c                 | 831 ++++++++++++++++++
 include/uapi/linux/serial_core.h              |   3 +
 5 files changed, 860 insertions(+)
 create mode 100644 drivers/tty/serial/rda-uart.c

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index aefd358a5ca3..98ee9eaa52be 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -1021,6 +1021,12 @@
 			specified address. The serial port must already be
 			setup and configured. Options are not yet supported.
 
+		rda,<addr>
+			Start an early, polled-mode console on a serial port
+			of an RDA Micro SoC, such as RDA8810PL, at the
+			specified address. The serial port must already be
+			setup and configured. Options are not yet supported.
+
 		smh	Use ARM semihosting calls for early console.
 
 		s3c2410,<addr>
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 32886c304641..67b9bf3b500e 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1529,6 +1529,25 @@ config SERIAL_OWL_CONSOLE
 	  Say 'Y' here if you wish to use Actions Semiconductor S500/S900 UART
 	  as the system console.
 
+config SERIAL_RDA
+	bool "RDA Micro serial port support"
+	depends on ARCH_RDA || COMPILE_TEST
+	select SERIAL_CORE
+	help
+	  This driver is for RDA8810PL SoC's UART.
+	  Say 'Y' here if you wish to use the on-board serial port.
+	  Otherwise, say 'N'.
+
+config SERIAL_RDA_CONSOLE
+	bool "Console on RDA Micro serial port"
+	depends on SERIAL_RDA=y
+	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
+	default y
+	help
+	  Say 'Y' here if you wish to use the RDA8810PL UART as the system
+	  console. Only earlycon is implemented currently.
+
 endmenu
 
 config SERIAL_MCTRL_GPIO
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index daac675612df..8c303736b7e8 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -89,6 +89,7 @@ obj-$(CONFIG_SERIAL_MVEBU_UART)	+= mvebu-uart.o
 obj-$(CONFIG_SERIAL_PIC32)	+= pic32_uart.o
 obj-$(CONFIG_SERIAL_MPS2_UART)	+= mps2-uart.o
 obj-$(CONFIG_SERIAL_OWL)	+= owl-uart.o
+obj-$(CONFIG_SERIAL_RDA)	+= rda-uart.o
 
 # GPIOLIB helpers for modem control lines
 obj-$(CONFIG_SERIAL_MCTRL_GPIO)	+= serial_mctrl_gpio.o
diff --git a/drivers/tty/serial/rda-uart.c b/drivers/tty/serial/rda-uart.c
new file mode 100644
index 000000000000..284623eefaeb
--- /dev/null
+++ b/drivers/tty/serial/rda-uart.c
@@ -0,0 +1,831 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * RDA8810PL serial device driver
+ *
+ * Copyright RDA Microelectronics Company Limited
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+
+#define RDA_UART_PORT_NUM 3
+#define RDA_UART_DEV_NAME "ttyRDA"
+
+#define RDA_UART_CTRL		0x00
+#define RDA_UART_STATUS		0x04
+#define RDA_UART_RXTX_BUFFER	0x08
+#define RDA_UART_IRQ_MASK	0x0c
+#define RDA_UART_IRQ_CAUSE	0x10
+#define RDA_UART_IRQ_TRIGGERS	0x14
+#define RDA_UART_CMD_SET	0x18
+#define RDA_UART_CMD_CLR	0x1c
+
+/* UART_CTRL Bits */
+#define RDA_UART_ENABLE			BIT(0)
+#define RDA_UART_DBITS_8		BIT(1)
+#define RDA_UART_TX_SBITS_2		BIT(2)
+#define RDA_UART_PARITY_EN		BIT(3)
+#define RDA_UART_PARITY(x)		(((x) & 0x3) << 4)
+#define RDA_UART_PARITY_ODD		RDA_UART_PARITY(0)
+#define RDA_UART_PARITY_EVEN		RDA_UART_PARITY(1)
+#define RDA_UART_PARITY_SPACE		RDA_UART_PARITY(2)
+#define RDA_UART_PARITY_MARK		RDA_UART_PARITY(3)
+#define RDA_UART_DIV_MODE		BIT(20)
+#define RDA_UART_IRDA_EN		BIT(21)
+#define RDA_UART_DMA_EN			BIT(22)
+#define RDA_UART_FLOW_CNT_EN		BIT(23)
+#define RDA_UART_LOOP_BACK_EN		BIT(24)
+#define RDA_UART_RX_LOCK_ERR		BIT(25)
+#define RDA_UART_RX_BREAK_LEN(x)	(((x) & 0xf) << 28)
+
+/* UART_STATUS Bits */
+#define RDA_UART_RX_FIFO(x)		(((x) & 0x7f) << 0)
+#define RDA_UART_RX_FIFO_MASK		(0x7f << 0)
+#define RDA_UART_TX_FIFO(x)		(((x) & 0x1f) << 8)
+#define RDA_UART_TX_FIFO_MASK		(0x1f << 8)
+#define RDA_UART_TX_ACTIVE		BIT(14)
+#define RDA_UART_RX_ACTIVE		BIT(15)
+#define RDA_UART_RX_OVERFLOW_ERR	BIT(16)
+#define RDA_UART_TX_OVERFLOW_ERR	BIT(17)
+#define RDA_UART_RX_PARITY_ERR		BIT(18)
+#define RDA_UART_RX_FRAMING_ERR		BIT(19)
+#define RDA_UART_RX_BREAK_INT		BIT(20)
+#define RDA_UART_DCTS			BIT(24)
+#define RDA_UART_CTS			BIT(25)
+#define RDA_UART_DTR			BIT(28)
+#define RDA_UART_CLK_ENABLED		BIT(31)
+
+/* UART_RXTX_BUFFER Bits */
+#define RDA_UART_RX_DATA(x)		(((x) & 0xff) << 0)
+#define RDA_UART_TX_DATA(x)		(((x) & 0xff) << 0)
+
+/* UART_IRQ_MASK Bits */
+#define RDA_UART_TX_MODEM_STATUS	BIT(0)
+#define RDA_UART_RX_DATA_AVAILABLE	BIT(1)
+#define RDA_UART_TX_DATA_NEEDED		BIT(2)
+#define RDA_UART_RX_TIMEOUT		BIT(3)
+#define RDA_UART_RX_LINE_ERR		BIT(4)
+#define RDA_UART_TX_DMA_DONE		BIT(5)
+#define RDA_UART_RX_DMA_DONE		BIT(6)
+#define RDA_UART_RX_DMA_TIMEOUT		BIT(7)
+#define RDA_UART_DTR_RISE		BIT(8)
+#define RDA_UART_DTR_FALL		BIT(9)
+
+/* UART_IRQ_CAUSE Bits */
+#define RDA_UART_TX_MODEM_STATUS_U	BIT(16)
+#define RDA_UART_RX_DATA_AVAILABLE_U	BIT(17)
+#define RDA_UART_TX_DATA_NEEDED_U	BIT(18)
+#define RDA_UART_RX_TIMEOUT_U		BIT(19)
+#define RDA_UART_RX_LINE_ERR_U		BIT(20)
+#define RDA_UART_TX_DMA_DONE_U		BIT(21)
+#define RDA_UART_RX_DMA_DONE_U		BIT(22)
+#define RDA_UART_RX_DMA_TIMEOUT_U	BIT(23)
+#define RDA_UART_DTR_RISE_U		BIT(24)
+#define RDA_UART_DTR_FALL_U		BIT(25)
+
+/* UART_TRIGGERS Bits */
+#define RDA_UART_RX_TRIGGER(x)		(((x) & 0x1f) << 0)
+#define RDA_UART_TX_TRIGGER(x)		(((x) & 0xf) << 8)
+#define RDA_UART_AFC_LEVEL(x)		(((x) & 0x1f) << 16)
+
+/* UART_CMD_SET Bits */
+#define RDA_UART_RI			BIT(0)
+#define RDA_UART_DCD			BIT(1)
+#define RDA_UART_DSR			BIT(2)
+#define RDA_UART_TX_BREAK_CONTROL	BIT(3)
+#define RDA_UART_TX_FINISH_N_WAIT	BIT(4)
+#define RDA_UART_RTS			BIT(5)
+#define RDA_UART_RX_FIFO_RESET		BIT(6)
+#define RDA_UART_TX_FIFO_RESET		BIT(7)
+
+#define RDA_UART_TX_FIFO_SIZE	16
+
+static struct uart_driver rda_uart_driver;
+
+struct rda_uart_port {
+	struct uart_port port;
+	struct clk *clk;
+};
+
+#define to_rda_uart_port(port) container_of(port, struct rda_uart_port, port)
+
+static struct rda_uart_port *rda_uart_ports[RDA_UART_PORT_NUM];
+
+static inline void rda_uart_write(struct uart_port *port, u32 val,
+				  unsigned int off)
+{
+	writel(val, port->membase + off);
+}
+
+static inline u32 rda_uart_read(struct uart_port *port, unsigned int off)
+{
+	return readl(port->membase + off);
+}
+
+static unsigned int rda_uart_tx_empty(struct uart_port *port)
+{
+	unsigned long flags;
+	unsigned int ret;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	val = rda_uart_read(port, RDA_UART_STATUS);
+	ret = (val & RDA_UART_TX_FIFO_MASK) ? TIOCSER_TEMT : 0;
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	return ret;
+}
+
+static unsigned int rda_uart_get_mctrl(struct uart_port *port)
+{
+	unsigned int mctrl = 0;
+	u32 cmd_set, status;
+
+	cmd_set = rda_uart_read(port, RDA_UART_CMD_SET);
+	status = rda_uart_read(port, RDA_UART_STATUS);
+	if (cmd_set & RDA_UART_RTS)
+		mctrl |= TIOCM_RTS;
+	if (!(status & RDA_UART_CTS))
+		mctrl |= TIOCM_CTS;
+
+	return mctrl;
+}
+
+static void rda_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	u32 val;
+
+	if (mctrl & TIOCM_RTS) {
+		val = rda_uart_read(port, RDA_UART_CMD_SET);
+		rda_uart_write(port, (val | RDA_UART_RTS), RDA_UART_CMD_SET);
+	} else {
+		/* Clear RTS to stop to receive. */
+		val = rda_uart_read(port, RDA_UART_CMD_CLR);
+		rda_uart_write(port, (val | RDA_UART_RTS), RDA_UART_CMD_CLR);
+	}
+
+	val = rda_uart_read(port, RDA_UART_CTRL);
+
+	if (mctrl & TIOCM_LOOP)
+		val |= RDA_UART_LOOP_BACK_EN;
+	else
+		val &= ~RDA_UART_LOOP_BACK_EN;
+
+	rda_uart_write(port, val, RDA_UART_CTRL);
+}
+
+static void rda_uart_stop_tx(struct uart_port *port)
+{
+	u32 val;
+
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val &= ~RDA_UART_TX_DATA_NEEDED;
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+
+	val = rda_uart_read(port, RDA_UART_CMD_SET);
+	val |= RDA_UART_TX_FIFO_RESET;
+	rda_uart_write(port, val, RDA_UART_CMD_SET);
+}
+
+static void rda_uart_stop_rx(struct uart_port *port)
+{
+	u32 val;
+
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val &= ~(RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT);
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+
+	/* Read Rx buffer before reset to avoid Rx timeout interrupt */
+	val = rda_uart_read(port, RDA_UART_RXTX_BUFFER);
+
+	val = rda_uart_read(port, RDA_UART_CMD_SET);
+	val |= RDA_UART_RX_FIFO_RESET;
+	rda_uart_write(port, val, RDA_UART_CMD_SET);
+}
+
+static void rda_uart_start_tx(struct uart_port *port)
+{
+	u32 val;
+
+	if (uart_tx_stopped(port)) {
+		rda_uart_stop_tx(port);
+		return;
+	}
+
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val |= RDA_UART_TX_DATA_NEEDED;
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+}
+
+static void rda_uart_change_baudrate(struct rda_uart_port *rda_port,
+				     unsigned long baud)
+{
+	clk_set_rate(rda_port->clk, baud * 8);
+}
+
+static void rda_uart_set_termios(struct uart_port *port,
+				 struct ktermios *termios,
+				 struct ktermios *old)
+{
+	struct rda_uart_port *rda_port = to_rda_uart_port(port);
+	unsigned long flags;
+	unsigned int ctrl, cmd_set, cmd_clr, triggers;
+	unsigned int baud;
+	u32 irq_mask;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	baud = uart_get_baud_rate(port, termios, old, 9600, port->uartclk / 4);
+	rda_uart_change_baudrate(rda_port, baud);
+
+	ctrl = rda_uart_read(port, RDA_UART_CTRL);
+	cmd_set = rda_uart_read(port, RDA_UART_CMD_SET);
+	cmd_clr = rda_uart_read(port, RDA_UART_CMD_CLR);
+
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+	case CS6:
+		dev_warn(port->dev, "bit size not supported, using 7 bits\n");
+		/* Fall through */
+	case CS7:
+		ctrl &= ~RDA_UART_DBITS_8;
+		break;
+	default:
+		ctrl |= RDA_UART_DBITS_8;
+		break;
+	}
+
+	/* stop bits */
+	if (termios->c_cflag & CSTOPB)
+		ctrl |= RDA_UART_TX_SBITS_2;
+	else
+		ctrl &= ~RDA_UART_TX_SBITS_2;
+
+	/* parity check */
+	if (termios->c_cflag & PARENB) {
+		ctrl |= RDA_UART_PARITY_EN;
+
+		/* Mark or Space parity */
+		if (termios->c_cflag & CMSPAR) {
+			if (termios->c_cflag & PARODD)
+				ctrl |= RDA_UART_PARITY_MARK;
+			else
+				ctrl |= RDA_UART_PARITY_SPACE;
+		} else if (termios->c_cflag & PARODD) {
+			ctrl |= RDA_UART_PARITY_ODD;
+		} else {
+			ctrl |= RDA_UART_PARITY_EVEN;
+		}
+	} else {
+		ctrl &= ~RDA_UART_PARITY_EN;
+	}
+
+	/* Hardware handshake (RTS/CTS) */
+	if (termios->c_cflag & CRTSCTS) {
+		ctrl   |= RDA_UART_FLOW_CNT_EN;
+		cmd_set |= RDA_UART_RTS;
+	} else {
+		ctrl   &= ~RDA_UART_FLOW_CNT_EN;
+		cmd_clr |= RDA_UART_RTS;
+	}
+
+	ctrl |= RDA_UART_ENABLE;
+	ctrl &= ~RDA_UART_DMA_EN;
+
+	triggers  = (RDA_UART_AFC_LEVEL(20) | RDA_UART_RX_TRIGGER(16));
+	irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+
+	rda_uart_write(port, triggers, RDA_UART_IRQ_TRIGGERS);
+	rda_uart_write(port, ctrl, RDA_UART_CTRL);
+	rda_uart_write(port, cmd_set, RDA_UART_CMD_SET);
+	rda_uart_write(port, cmd_clr, RDA_UART_CMD_CLR);
+
+	rda_uart_write(port, irq_mask, RDA_UART_IRQ_MASK);
+
+	/* Don't rewrite B0 */
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+
+	/* update the per-port timeout */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void rda_uart_send_chars(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->state->xmit;
+	unsigned int ch;
+	u32 val;
+
+	if (uart_tx_stopped(port))
+		return;
+
+	if (port->x_char) {
+		while (!(rda_uart_read(port, RDA_UART_STATUS) &
+			 RDA_UART_TX_FIFO_MASK))
+			cpu_relax();
+
+		rda_uart_write(port, port->x_char, RDA_UART_RXTX_BUFFER);
+		port->icount.tx++;
+		port->x_char = 0;
+	}
+
+	while (rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK) {
+		if (uart_circ_empty(xmit))
+			break;
+
+		ch = xmit->buf[xmit->tail];
+		rda_uart_write(port, ch, RDA_UART_RXTX_BUFFER);
+		xmit->tail = (xmit->tail + 1) & (SERIAL_XMIT_SIZE - 1);
+		port->icount.tx++;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (!uart_circ_empty(xmit)) {
+		/* Re-enable Tx FIFO interrupt */
+		val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+		val |= RDA_UART_TX_DATA_NEEDED;
+		rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+	}
+}
+
+static void rda_uart_receive_chars(struct uart_port *port)
+{
+	u32 status, val;
+
+	status = rda_uart_read(port, RDA_UART_STATUS);
+	while ((status & RDA_UART_RX_FIFO_MASK)) {
+		char flag = TTY_NORMAL;
+
+		if (status & RDA_UART_RX_PARITY_ERR) {
+			port->icount.parity++;
+			flag = TTY_PARITY;
+		}
+
+		if (status & RDA_UART_RX_FRAMING_ERR) {
+			port->icount.frame++;
+			flag = TTY_FRAME;
+		}
+
+		if (status & RDA_UART_RX_OVERFLOW_ERR) {
+			port->icount.overrun++;
+			flag = TTY_OVERRUN;
+		}
+
+		val = rda_uart_read(port, RDA_UART_RXTX_BUFFER);
+		val &= 0xff;
+
+		port->icount.rx++;
+		tty_insert_flip_char(&port->state->port, val, flag);
+
+		status = rda_uart_read(port, RDA_UART_STATUS);
+	}
+
+	spin_unlock(&port->lock);
+	tty_flip_buffer_push(&port->state->port);
+	spin_lock(&port->lock);
+}
+
+static irqreturn_t rda_interrupt(int irq, void *dev_id)
+{
+	struct uart_port *port = dev_id;
+	unsigned long flags;
+	u32 val, irq_mask;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* Clear IRQ cause */
+	val = rda_uart_read(port, RDA_UART_IRQ_CAUSE);
+	rda_uart_write(port, val, RDA_UART_IRQ_CAUSE);
+
+	if (val & (RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT))
+		rda_uart_receive_chars(port);
+
+	if (val & (RDA_UART_TX_DATA_NEEDED)) {
+		irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
+		irq_mask &= ~RDA_UART_TX_DATA_NEEDED;
+		rda_uart_write(port, irq_mask, RDA_UART_IRQ_MASK);
+
+		rda_uart_send_chars(port);
+	}
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+static int rda_uart_startup(struct uart_port *port)
+{
+	unsigned long flags;
+	int ret;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	ret = request_irq(port->irq, rda_interrupt, IRQF_NO_SUSPEND,
+			  "rda-uart", port);
+	if (ret)
+		return ret;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	val = rda_uart_read(port, RDA_UART_CTRL);
+	val |= RDA_UART_ENABLE;
+	rda_uart_write(port, val, RDA_UART_CTRL);
+
+	/* enable rx interrupt */
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val |= (RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT);
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	return 0;
+}
+
+static void rda_uart_shutdown(struct uart_port *port)
+{
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	rda_uart_stop_tx(port);
+	rda_uart_stop_rx(port);
+
+	val = rda_uart_read(port, RDA_UART_CTRL);
+	val &= ~RDA_UART_ENABLE;
+	rda_uart_write(port, val, RDA_UART_CTRL);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *rda_uart_type(struct uart_port *port)
+{
+	return (port->type == PORT_RDA) ? "rda-uart" : NULL;
+}
+
+static int rda_uart_request_port(struct uart_port *port)
+{
+	struct platform_device *pdev = to_platform_device(port->dev);
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENXIO;
+
+	if (!devm_request_mem_region(port->dev, port->mapbase,
+				     resource_size(res), dev_name(port->dev)))
+		return -EBUSY;
+
+	if (port->flags & UPF_IOREMAP) {
+		port->membase = devm_ioremap_nocache(port->dev, port->mapbase,
+						     resource_size(res));
+		if (!port->membase)
+			return -EBUSY;
+	}
+
+	return 0;
+}
+
+static void rda_uart_config_port(struct uart_port *port, int flags)
+{
+	unsigned long irq_flags;
+
+	if (flags & UART_CONFIG_TYPE) {
+		port->type = PORT_RDA;
+		rda_uart_request_port(port);
+	}
+
+	spin_lock_irqsave(&port->lock, irq_flags);
+
+	/* Clear mask, so no surprise interrupts. */
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+
+	/* Clear status register */
+	rda_uart_write(port, 0, RDA_UART_STATUS);
+
+	spin_unlock_irqrestore(&port->lock, irq_flags);
+}
+
+static void rda_uart_release_port(struct uart_port *port)
+{
+	struct platform_device *pdev = to_platform_device(port->dev);
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return;
+
+	if (port->flags & UPF_IOREMAP) {
+		devm_release_mem_region(port->dev, port->mapbase,
+					resource_size(res));
+		devm_iounmap(port->dev, port->membase);
+		port->membase = NULL;
+	}
+}
+
+static int rda_uart_verify_port(struct uart_port *port,
+				struct serial_struct *ser)
+{
+	if (port->type != PORT_RDA)
+		return -EINVAL;
+
+	if (port->irq != ser->irq)
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct uart_ops rda_uart_ops = {
+	.tx_empty       = rda_uart_tx_empty,
+	.get_mctrl      = rda_uart_get_mctrl,
+	.set_mctrl      = rda_uart_set_mctrl,
+	.start_tx       = rda_uart_start_tx,
+	.stop_tx        = rda_uart_stop_tx,
+	.stop_rx        = rda_uart_stop_rx,
+	.startup        = rda_uart_startup,
+	.shutdown       = rda_uart_shutdown,
+	.set_termios    = rda_uart_set_termios,
+	.type           = rda_uart_type,
+	.request_port	= rda_uart_request_port,
+	.release_port	= rda_uart_release_port,
+	.config_port	= rda_uart_config_port,
+	.verify_port	= rda_uart_verify_port,
+};
+
+#ifdef CONFIG_SERIAL_RDA_CONSOLE
+
+static void rda_console_putchar(struct uart_port *port, int ch)
+{
+	if (!port->membase)
+		return;
+
+	while (!(rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK))
+		cpu_relax();
+
+	rda_uart_write(port, ch, RDA_UART_RXTX_BUFFER);
+}
+
+static void rda_uart_port_write(struct uart_port *port, const char *s,
+				u_int count)
+{
+	u32 old_irq_mask;
+	unsigned long flags;
+	int locked;
+
+	local_irq_save(flags);
+
+	if (port->sysrq) {
+		locked = 0;
+	} else if (oops_in_progress) {
+		locked = spin_trylock(&port->lock);
+	} else {
+		spin_lock(&port->lock);
+		locked = 1;
+	}
+
+	old_irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+
+	uart_console_write(port, s, count, rda_console_putchar);
+
+	/* wait until all contents have been sent out */
+	while (!(rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK))
+		cpu_relax();
+
+	rda_uart_write(port, old_irq_mask, RDA_UART_IRQ_MASK);
+
+	if (locked)
+		spin_unlock(&port->lock);
+
+	local_irq_restore(flags);
+}
+
+static void rda_uart_console_write(struct console *co, const char *s,
+				   u_int count)
+{
+	struct rda_uart_port *rda_port;
+
+	rda_port = rda_uart_ports[co->index];
+	if (!rda_port)
+		return;
+
+	rda_uart_port_write(&rda_port->port, s, count);
+}
+
+static int rda_uart_console_setup(struct console *co, char *options)
+{
+	struct rda_uart_port *rda_port;
+	int baud = 921600;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index < 0 || co->index >= RDA_UART_PORT_NUM)
+		return -EINVAL;
+
+	rda_port = rda_uart_ports[co->index];
+	if (!rda_port || !rda_port->port.membase)
+		return -ENODEV;
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(&rda_port->port, co, baud, parity, bits, flow);
+}
+
+static struct console rda_uart_console = {
+	.name = RDA_UART_DEV_NAME,
+	.write = rda_uart_console_write,
+	.device = uart_console_device,
+	.setup = rda_uart_console_setup,
+	.flags = CON_PRINTBUFFER,
+	.index = -1,
+	.data = &rda_uart_driver,
+};
+
+static int __init rda_uart_console_init(void)
+{
+	register_console(&rda_uart_console);
+
+	return 0;
+}
+console_initcall(rda_uart_console_init);
+
+static void rda_uart_early_console_write(struct console *co,
+					 const char *s,
+					 u_int count)
+{
+	struct earlycon_device *dev = co->data;
+
+	rda_uart_port_write(&dev->port, s, count);
+}
+
+static int __init
+rda_uart_early_console_setup(struct earlycon_device *device, const char *opt)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = rda_uart_early_console_write;
+
+	return 0;
+}
+
+OF_EARLYCON_DECLARE(rda, "rda,8810pl-uart",
+		    rda_uart_early_console_setup);
+
+#define RDA_UART_CONSOLE (&rda_uart_console)
+#else
+#define RDA_UART_CONSOLE NULL
+#endif /* CONFIG_SERIAL_RDA_CONSOLE */
+
+static struct uart_driver rda_uart_driver = {
+	.owner = THIS_MODULE,
+	.driver_name = "rda-uart",
+	.dev_name = RDA_UART_DEV_NAME,
+	.nr = RDA_UART_PORT_NUM,
+	.cons = RDA_UART_CONSOLE,
+};
+
+static const struct of_device_id rda_uart_dt_matches[] = {
+	{ .compatible = "rda,8810pl-uart" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, rda_uart_dt_matches);
+
+static int rda_uart_probe(struct platform_device *pdev)
+{
+	struct resource *res_mem;
+	struct rda_uart_port *rda_port;
+	int ret, irq;
+
+	if (pdev->dev.of_node)
+		pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
+
+	if (pdev->id < 0 || pdev->id >= RDA_UART_PORT_NUM) {
+		dev_err(&pdev->dev, "id %d out of range\n", pdev->id);
+		return -EINVAL;
+	}
+
+	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res_mem) {
+		dev_err(&pdev->dev, "could not get mem\n");
+		return -ENODEV;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "could not get irq\n");
+		return irq;
+	}
+
+	if (rda_uart_ports[pdev->id]) {
+		dev_err(&pdev->dev, "port %d already allocated\n", pdev->id);
+		return -EBUSY;
+	}
+
+	rda_port = devm_kzalloc(&pdev->dev, sizeof(*rda_port), GFP_KERNEL);
+	if (!rda_port)
+		return -ENOMEM;
+
+	rda_port->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(rda_port->clk)) {
+		dev_err(&pdev->dev, "could not get clk\n");
+		return PTR_ERR(rda_port->clk);
+	}
+
+	rda_port->port.dev = &pdev->dev;
+	rda_port->port.regshift = 0;
+	rda_port->port.line = pdev->id;
+	rda_port->port.type = PORT_RDA;
+	rda_port->port.iotype = UPIO_MEM;
+	rda_port->port.mapbase = res_mem->start;
+	rda_port->port.irq = irq;
+	rda_port->port.uartclk = clk_get_rate(rda_port->clk);
+	if (rda_port->port.uartclk == 0) {
+		dev_err(&pdev->dev, "clock rate is zero\n");
+		return -EINVAL;
+	}
+	rda_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP |
+			       UPF_LOW_LATENCY;
+	rda_port->port.x_char = 0;
+	rda_port->port.fifosize = RDA_UART_TX_FIFO_SIZE;
+	rda_port->port.ops = &rda_uart_ops;
+
+	rda_uart_ports[pdev->id] = rda_port;
+	platform_set_drvdata(pdev, rda_port);
+
+	ret = uart_add_one_port(&rda_uart_driver, &rda_port->port);
+	if (ret)
+		rda_uart_ports[pdev->id] = NULL;
+
+	return ret;
+}
+
+static int rda_uart_remove(struct platform_device *pdev)
+{
+	struct rda_uart_port *rda_port = platform_get_drvdata(pdev);
+
+	uart_remove_one_port(&rda_uart_driver, &rda_port->port);
+	rda_uart_ports[pdev->id] = NULL;
+
+	return 0;
+}
+
+static struct platform_driver rda_uart_platform_driver = {
+	.probe = rda_uart_probe,
+	.remove = rda_uart_remove,
+	.driver = {
+		.name = "rda-uart",
+		.of_match_table = rda_uart_dt_matches,
+	},
+};
+
+static int __init rda_uart_init(void)
+{
+	int ret;
+
+	ret = uart_register_driver(&rda_uart_driver);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&rda_uart_platform_driver);
+	if (ret)
+		uart_unregister_driver(&rda_uart_driver);
+
+	return ret;
+}
+
+static void __init rda_uart_exit(void)
+{
+	platform_driver_unregister(&rda_uart_platform_driver);
+	uart_unregister_driver(&rda_uart_driver);
+}
+
+module_init(rda_uart_init);
+module_exit(rda_uart_exit);
+
+MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>");
+MODULE_DESCRIPTION("RDA8810PL serial device driver");
+MODULE_LICENSE("GPL");
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index dce5f9dae121..df4a7534e239 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -281,4 +281,7 @@
 /* MediaTek BTIF */
 #define PORT_MTK_BTIF	117
 
+/* RDA UART */
+#define PORT_RDA	118
+
 #endif /* _UAPILINUX_SERIAL_CORE_H */
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 10/11] tty: serial: Add RDA8810PL UART driver
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

Add UART driver for RDA Micro RDA8810PL SoC.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 .../admin-guide/kernel-parameters.txt         |   6 +
 drivers/tty/serial/Kconfig                    |  19 +
 drivers/tty/serial/Makefile                   |   1 +
 drivers/tty/serial/rda-uart.c                 | 831 ++++++++++++++++++
 include/uapi/linux/serial_core.h              |   3 +
 5 files changed, 860 insertions(+)
 create mode 100644 drivers/tty/serial/rda-uart.c

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index aefd358a5ca3..98ee9eaa52be 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -1021,6 +1021,12 @@
 			specified address. The serial port must already be
 			setup and configured. Options are not yet supported.
 
+		rda,<addr>
+			Start an early, polled-mode console on a serial port
+			of an RDA Micro SoC, such as RDA8810PL, at the
+			specified address. The serial port must already be
+			setup and configured. Options are not yet supported.
+
 		smh	Use ARM semihosting calls for early console.
 
 		s3c2410,<addr>
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 32886c304641..67b9bf3b500e 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1529,6 +1529,25 @@ config SERIAL_OWL_CONSOLE
 	  Say 'Y' here if you wish to use Actions Semiconductor S500/S900 UART
 	  as the system console.
 
+config SERIAL_RDA
+	bool "RDA Micro serial port support"
+	depends on ARCH_RDA || COMPILE_TEST
+	select SERIAL_CORE
+	help
+	  This driver is for RDA8810PL SoC's UART.
+	  Say 'Y' here if you wish to use the on-board serial port.
+	  Otherwise, say 'N'.
+
+config SERIAL_RDA_CONSOLE
+	bool "Console on RDA Micro serial port"
+	depends on SERIAL_RDA=y
+	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
+	default y
+	help
+	  Say 'Y' here if you wish to use the RDA8810PL UART as the system
+	  console. Only earlycon is implemented currently.
+
 endmenu
 
 config SERIAL_MCTRL_GPIO
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index daac675612df..8c303736b7e8 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -89,6 +89,7 @@ obj-$(CONFIG_SERIAL_MVEBU_UART)	+= mvebu-uart.o
 obj-$(CONFIG_SERIAL_PIC32)	+= pic32_uart.o
 obj-$(CONFIG_SERIAL_MPS2_UART)	+= mps2-uart.o
 obj-$(CONFIG_SERIAL_OWL)	+= owl-uart.o
+obj-$(CONFIG_SERIAL_RDA)	+= rda-uart.o
 
 # GPIOLIB helpers for modem control lines
 obj-$(CONFIG_SERIAL_MCTRL_GPIO)	+= serial_mctrl_gpio.o
diff --git a/drivers/tty/serial/rda-uart.c b/drivers/tty/serial/rda-uart.c
new file mode 100644
index 000000000000..284623eefaeb
--- /dev/null
+++ b/drivers/tty/serial/rda-uart.c
@@ -0,0 +1,831 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * RDA8810PL serial device driver
+ *
+ * Copyright RDA Microelectronics Company Limited
+ * Copyright (c) 2017 Andreas Färber
+ * Copyright (c) 2018 Manivannan Sadhasivam
+ */
+
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+
+#define RDA_UART_PORT_NUM 3
+#define RDA_UART_DEV_NAME "ttyRDA"
+
+#define RDA_UART_CTRL		0x00
+#define RDA_UART_STATUS		0x04
+#define RDA_UART_RXTX_BUFFER	0x08
+#define RDA_UART_IRQ_MASK	0x0c
+#define RDA_UART_IRQ_CAUSE	0x10
+#define RDA_UART_IRQ_TRIGGERS	0x14
+#define RDA_UART_CMD_SET	0x18
+#define RDA_UART_CMD_CLR	0x1c
+
+/* UART_CTRL Bits */
+#define RDA_UART_ENABLE			BIT(0)
+#define RDA_UART_DBITS_8		BIT(1)
+#define RDA_UART_TX_SBITS_2		BIT(2)
+#define RDA_UART_PARITY_EN		BIT(3)
+#define RDA_UART_PARITY(x)		(((x) & 0x3) << 4)
+#define RDA_UART_PARITY_ODD		RDA_UART_PARITY(0)
+#define RDA_UART_PARITY_EVEN		RDA_UART_PARITY(1)
+#define RDA_UART_PARITY_SPACE		RDA_UART_PARITY(2)
+#define RDA_UART_PARITY_MARK		RDA_UART_PARITY(3)
+#define RDA_UART_DIV_MODE		BIT(20)
+#define RDA_UART_IRDA_EN		BIT(21)
+#define RDA_UART_DMA_EN			BIT(22)
+#define RDA_UART_FLOW_CNT_EN		BIT(23)
+#define RDA_UART_LOOP_BACK_EN		BIT(24)
+#define RDA_UART_RX_LOCK_ERR		BIT(25)
+#define RDA_UART_RX_BREAK_LEN(x)	(((x) & 0xf) << 28)
+
+/* UART_STATUS Bits */
+#define RDA_UART_RX_FIFO(x)		(((x) & 0x7f) << 0)
+#define RDA_UART_RX_FIFO_MASK		(0x7f << 0)
+#define RDA_UART_TX_FIFO(x)		(((x) & 0x1f) << 8)
+#define RDA_UART_TX_FIFO_MASK		(0x1f << 8)
+#define RDA_UART_TX_ACTIVE		BIT(14)
+#define RDA_UART_RX_ACTIVE		BIT(15)
+#define RDA_UART_RX_OVERFLOW_ERR	BIT(16)
+#define RDA_UART_TX_OVERFLOW_ERR	BIT(17)
+#define RDA_UART_RX_PARITY_ERR		BIT(18)
+#define RDA_UART_RX_FRAMING_ERR		BIT(19)
+#define RDA_UART_RX_BREAK_INT		BIT(20)
+#define RDA_UART_DCTS			BIT(24)
+#define RDA_UART_CTS			BIT(25)
+#define RDA_UART_DTR			BIT(28)
+#define RDA_UART_CLK_ENABLED		BIT(31)
+
+/* UART_RXTX_BUFFER Bits */
+#define RDA_UART_RX_DATA(x)		(((x) & 0xff) << 0)
+#define RDA_UART_TX_DATA(x)		(((x) & 0xff) << 0)
+
+/* UART_IRQ_MASK Bits */
+#define RDA_UART_TX_MODEM_STATUS	BIT(0)
+#define RDA_UART_RX_DATA_AVAILABLE	BIT(1)
+#define RDA_UART_TX_DATA_NEEDED		BIT(2)
+#define RDA_UART_RX_TIMEOUT		BIT(3)
+#define RDA_UART_RX_LINE_ERR		BIT(4)
+#define RDA_UART_TX_DMA_DONE		BIT(5)
+#define RDA_UART_RX_DMA_DONE		BIT(6)
+#define RDA_UART_RX_DMA_TIMEOUT		BIT(7)
+#define RDA_UART_DTR_RISE		BIT(8)
+#define RDA_UART_DTR_FALL		BIT(9)
+
+/* UART_IRQ_CAUSE Bits */
+#define RDA_UART_TX_MODEM_STATUS_U	BIT(16)
+#define RDA_UART_RX_DATA_AVAILABLE_U	BIT(17)
+#define RDA_UART_TX_DATA_NEEDED_U	BIT(18)
+#define RDA_UART_RX_TIMEOUT_U		BIT(19)
+#define RDA_UART_RX_LINE_ERR_U		BIT(20)
+#define RDA_UART_TX_DMA_DONE_U		BIT(21)
+#define RDA_UART_RX_DMA_DONE_U		BIT(22)
+#define RDA_UART_RX_DMA_TIMEOUT_U	BIT(23)
+#define RDA_UART_DTR_RISE_U		BIT(24)
+#define RDA_UART_DTR_FALL_U		BIT(25)
+
+/* UART_TRIGGERS Bits */
+#define RDA_UART_RX_TRIGGER(x)		(((x) & 0x1f) << 0)
+#define RDA_UART_TX_TRIGGER(x)		(((x) & 0xf) << 8)
+#define RDA_UART_AFC_LEVEL(x)		(((x) & 0x1f) << 16)
+
+/* UART_CMD_SET Bits */
+#define RDA_UART_RI			BIT(0)
+#define RDA_UART_DCD			BIT(1)
+#define RDA_UART_DSR			BIT(2)
+#define RDA_UART_TX_BREAK_CONTROL	BIT(3)
+#define RDA_UART_TX_FINISH_N_WAIT	BIT(4)
+#define RDA_UART_RTS			BIT(5)
+#define RDA_UART_RX_FIFO_RESET		BIT(6)
+#define RDA_UART_TX_FIFO_RESET		BIT(7)
+
+#define RDA_UART_TX_FIFO_SIZE	16
+
+static struct uart_driver rda_uart_driver;
+
+struct rda_uart_port {
+	struct uart_port port;
+	struct clk *clk;
+};
+
+#define to_rda_uart_port(port) container_of(port, struct rda_uart_port, port)
+
+static struct rda_uart_port *rda_uart_ports[RDA_UART_PORT_NUM];
+
+static inline void rda_uart_write(struct uart_port *port, u32 val,
+				  unsigned int off)
+{
+	writel(val, port->membase + off);
+}
+
+static inline u32 rda_uart_read(struct uart_port *port, unsigned int off)
+{
+	return readl(port->membase + off);
+}
+
+static unsigned int rda_uart_tx_empty(struct uart_port *port)
+{
+	unsigned long flags;
+	unsigned int ret;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	val = rda_uart_read(port, RDA_UART_STATUS);
+	ret = (val & RDA_UART_TX_FIFO_MASK) ? TIOCSER_TEMT : 0;
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	return ret;
+}
+
+static unsigned int rda_uart_get_mctrl(struct uart_port *port)
+{
+	unsigned int mctrl = 0;
+	u32 cmd_set, status;
+
+	cmd_set = rda_uart_read(port, RDA_UART_CMD_SET);
+	status = rda_uart_read(port, RDA_UART_STATUS);
+	if (cmd_set & RDA_UART_RTS)
+		mctrl |= TIOCM_RTS;
+	if (!(status & RDA_UART_CTS))
+		mctrl |= TIOCM_CTS;
+
+	return mctrl;
+}
+
+static void rda_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	u32 val;
+
+	if (mctrl & TIOCM_RTS) {
+		val = rda_uart_read(port, RDA_UART_CMD_SET);
+		rda_uart_write(port, (val | RDA_UART_RTS), RDA_UART_CMD_SET);
+	} else {
+		/* Clear RTS to stop to receive. */
+		val = rda_uart_read(port, RDA_UART_CMD_CLR);
+		rda_uart_write(port, (val | RDA_UART_RTS), RDA_UART_CMD_CLR);
+	}
+
+	val = rda_uart_read(port, RDA_UART_CTRL);
+
+	if (mctrl & TIOCM_LOOP)
+		val |= RDA_UART_LOOP_BACK_EN;
+	else
+		val &= ~RDA_UART_LOOP_BACK_EN;
+
+	rda_uart_write(port, val, RDA_UART_CTRL);
+}
+
+static void rda_uart_stop_tx(struct uart_port *port)
+{
+	u32 val;
+
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val &= ~RDA_UART_TX_DATA_NEEDED;
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+
+	val = rda_uart_read(port, RDA_UART_CMD_SET);
+	val |= RDA_UART_TX_FIFO_RESET;
+	rda_uart_write(port, val, RDA_UART_CMD_SET);
+}
+
+static void rda_uart_stop_rx(struct uart_port *port)
+{
+	u32 val;
+
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val &= ~(RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT);
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+
+	/* Read Rx buffer before reset to avoid Rx timeout interrupt */
+	val = rda_uart_read(port, RDA_UART_RXTX_BUFFER);
+
+	val = rda_uart_read(port, RDA_UART_CMD_SET);
+	val |= RDA_UART_RX_FIFO_RESET;
+	rda_uart_write(port, val, RDA_UART_CMD_SET);
+}
+
+static void rda_uart_start_tx(struct uart_port *port)
+{
+	u32 val;
+
+	if (uart_tx_stopped(port)) {
+		rda_uart_stop_tx(port);
+		return;
+	}
+
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val |= RDA_UART_TX_DATA_NEEDED;
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+}
+
+static void rda_uart_change_baudrate(struct rda_uart_port *rda_port,
+				     unsigned long baud)
+{
+	clk_set_rate(rda_port->clk, baud * 8);
+}
+
+static void rda_uart_set_termios(struct uart_port *port,
+				 struct ktermios *termios,
+				 struct ktermios *old)
+{
+	struct rda_uart_port *rda_port = to_rda_uart_port(port);
+	unsigned long flags;
+	unsigned int ctrl, cmd_set, cmd_clr, triggers;
+	unsigned int baud;
+	u32 irq_mask;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	baud = uart_get_baud_rate(port, termios, old, 9600, port->uartclk / 4);
+	rda_uart_change_baudrate(rda_port, baud);
+
+	ctrl = rda_uart_read(port, RDA_UART_CTRL);
+	cmd_set = rda_uart_read(port, RDA_UART_CMD_SET);
+	cmd_clr = rda_uart_read(port, RDA_UART_CMD_CLR);
+
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+	case CS6:
+		dev_warn(port->dev, "bit size not supported, using 7 bits\n");
+		/* Fall through */
+	case CS7:
+		ctrl &= ~RDA_UART_DBITS_8;
+		break;
+	default:
+		ctrl |= RDA_UART_DBITS_8;
+		break;
+	}
+
+	/* stop bits */
+	if (termios->c_cflag & CSTOPB)
+		ctrl |= RDA_UART_TX_SBITS_2;
+	else
+		ctrl &= ~RDA_UART_TX_SBITS_2;
+
+	/* parity check */
+	if (termios->c_cflag & PARENB) {
+		ctrl |= RDA_UART_PARITY_EN;
+
+		/* Mark or Space parity */
+		if (termios->c_cflag & CMSPAR) {
+			if (termios->c_cflag & PARODD)
+				ctrl |= RDA_UART_PARITY_MARK;
+			else
+				ctrl |= RDA_UART_PARITY_SPACE;
+		} else if (termios->c_cflag & PARODD) {
+			ctrl |= RDA_UART_PARITY_ODD;
+		} else {
+			ctrl |= RDA_UART_PARITY_EVEN;
+		}
+	} else {
+		ctrl &= ~RDA_UART_PARITY_EN;
+	}
+
+	/* Hardware handshake (RTS/CTS) */
+	if (termios->c_cflag & CRTSCTS) {
+		ctrl   |= RDA_UART_FLOW_CNT_EN;
+		cmd_set |= RDA_UART_RTS;
+	} else {
+		ctrl   &= ~RDA_UART_FLOW_CNT_EN;
+		cmd_clr |= RDA_UART_RTS;
+	}
+
+	ctrl |= RDA_UART_ENABLE;
+	ctrl &= ~RDA_UART_DMA_EN;
+
+	triggers  = (RDA_UART_AFC_LEVEL(20) | RDA_UART_RX_TRIGGER(16));
+	irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+
+	rda_uart_write(port, triggers, RDA_UART_IRQ_TRIGGERS);
+	rda_uart_write(port, ctrl, RDA_UART_CTRL);
+	rda_uart_write(port, cmd_set, RDA_UART_CMD_SET);
+	rda_uart_write(port, cmd_clr, RDA_UART_CMD_CLR);
+
+	rda_uart_write(port, irq_mask, RDA_UART_IRQ_MASK);
+
+	/* Don't rewrite B0 */
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+
+	/* update the per-port timeout */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void rda_uart_send_chars(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->state->xmit;
+	unsigned int ch;
+	u32 val;
+
+	if (uart_tx_stopped(port))
+		return;
+
+	if (port->x_char) {
+		while (!(rda_uart_read(port, RDA_UART_STATUS) &
+			 RDA_UART_TX_FIFO_MASK))
+			cpu_relax();
+
+		rda_uart_write(port, port->x_char, RDA_UART_RXTX_BUFFER);
+		port->icount.tx++;
+		port->x_char = 0;
+	}
+
+	while (rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK) {
+		if (uart_circ_empty(xmit))
+			break;
+
+		ch = xmit->buf[xmit->tail];
+		rda_uart_write(port, ch, RDA_UART_RXTX_BUFFER);
+		xmit->tail = (xmit->tail + 1) & (SERIAL_XMIT_SIZE - 1);
+		port->icount.tx++;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (!uart_circ_empty(xmit)) {
+		/* Re-enable Tx FIFO interrupt */
+		val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+		val |= RDA_UART_TX_DATA_NEEDED;
+		rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+	}
+}
+
+static void rda_uart_receive_chars(struct uart_port *port)
+{
+	u32 status, val;
+
+	status = rda_uart_read(port, RDA_UART_STATUS);
+	while ((status & RDA_UART_RX_FIFO_MASK)) {
+		char flag = TTY_NORMAL;
+
+		if (status & RDA_UART_RX_PARITY_ERR) {
+			port->icount.parity++;
+			flag = TTY_PARITY;
+		}
+
+		if (status & RDA_UART_RX_FRAMING_ERR) {
+			port->icount.frame++;
+			flag = TTY_FRAME;
+		}
+
+		if (status & RDA_UART_RX_OVERFLOW_ERR) {
+			port->icount.overrun++;
+			flag = TTY_OVERRUN;
+		}
+
+		val = rda_uart_read(port, RDA_UART_RXTX_BUFFER);
+		val &= 0xff;
+
+		port->icount.rx++;
+		tty_insert_flip_char(&port->state->port, val, flag);
+
+		status = rda_uart_read(port, RDA_UART_STATUS);
+	}
+
+	spin_unlock(&port->lock);
+	tty_flip_buffer_push(&port->state->port);
+	spin_lock(&port->lock);
+}
+
+static irqreturn_t rda_interrupt(int irq, void *dev_id)
+{
+	struct uart_port *port = dev_id;
+	unsigned long flags;
+	u32 val, irq_mask;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* Clear IRQ cause */
+	val = rda_uart_read(port, RDA_UART_IRQ_CAUSE);
+	rda_uart_write(port, val, RDA_UART_IRQ_CAUSE);
+
+	if (val & (RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT))
+		rda_uart_receive_chars(port);
+
+	if (val & (RDA_UART_TX_DATA_NEEDED)) {
+		irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
+		irq_mask &= ~RDA_UART_TX_DATA_NEEDED;
+		rda_uart_write(port, irq_mask, RDA_UART_IRQ_MASK);
+
+		rda_uart_send_chars(port);
+	}
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+static int rda_uart_startup(struct uart_port *port)
+{
+	unsigned long flags;
+	int ret;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	ret = request_irq(port->irq, rda_interrupt, IRQF_NO_SUSPEND,
+			  "rda-uart", port);
+	if (ret)
+		return ret;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	val = rda_uart_read(port, RDA_UART_CTRL);
+	val |= RDA_UART_ENABLE;
+	rda_uart_write(port, val, RDA_UART_CTRL);
+
+	/* enable rx interrupt */
+	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	val |= (RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT);
+	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	return 0;
+}
+
+static void rda_uart_shutdown(struct uart_port *port)
+{
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	rda_uart_stop_tx(port);
+	rda_uart_stop_rx(port);
+
+	val = rda_uart_read(port, RDA_UART_CTRL);
+	val &= ~RDA_UART_ENABLE;
+	rda_uart_write(port, val, RDA_UART_CTRL);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *rda_uart_type(struct uart_port *port)
+{
+	return (port->type == PORT_RDA) ? "rda-uart" : NULL;
+}
+
+static int rda_uart_request_port(struct uart_port *port)
+{
+	struct platform_device *pdev = to_platform_device(port->dev);
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENXIO;
+
+	if (!devm_request_mem_region(port->dev, port->mapbase,
+				     resource_size(res), dev_name(port->dev)))
+		return -EBUSY;
+
+	if (port->flags & UPF_IOREMAP) {
+		port->membase = devm_ioremap_nocache(port->dev, port->mapbase,
+						     resource_size(res));
+		if (!port->membase)
+			return -EBUSY;
+	}
+
+	return 0;
+}
+
+static void rda_uart_config_port(struct uart_port *port, int flags)
+{
+	unsigned long irq_flags;
+
+	if (flags & UART_CONFIG_TYPE) {
+		port->type = PORT_RDA;
+		rda_uart_request_port(port);
+	}
+
+	spin_lock_irqsave(&port->lock, irq_flags);
+
+	/* Clear mask, so no surprise interrupts. */
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+
+	/* Clear status register */
+	rda_uart_write(port, 0, RDA_UART_STATUS);
+
+	spin_unlock_irqrestore(&port->lock, irq_flags);
+}
+
+static void rda_uart_release_port(struct uart_port *port)
+{
+	struct platform_device *pdev = to_platform_device(port->dev);
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return;
+
+	if (port->flags & UPF_IOREMAP) {
+		devm_release_mem_region(port->dev, port->mapbase,
+					resource_size(res));
+		devm_iounmap(port->dev, port->membase);
+		port->membase = NULL;
+	}
+}
+
+static int rda_uart_verify_port(struct uart_port *port,
+				struct serial_struct *ser)
+{
+	if (port->type != PORT_RDA)
+		return -EINVAL;
+
+	if (port->irq != ser->irq)
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct uart_ops rda_uart_ops = {
+	.tx_empty       = rda_uart_tx_empty,
+	.get_mctrl      = rda_uart_get_mctrl,
+	.set_mctrl      = rda_uart_set_mctrl,
+	.start_tx       = rda_uart_start_tx,
+	.stop_tx        = rda_uart_stop_tx,
+	.stop_rx        = rda_uart_stop_rx,
+	.startup        = rda_uart_startup,
+	.shutdown       = rda_uart_shutdown,
+	.set_termios    = rda_uart_set_termios,
+	.type           = rda_uart_type,
+	.request_port	= rda_uart_request_port,
+	.release_port	= rda_uart_release_port,
+	.config_port	= rda_uart_config_port,
+	.verify_port	= rda_uart_verify_port,
+};
+
+#ifdef CONFIG_SERIAL_RDA_CONSOLE
+
+static void rda_console_putchar(struct uart_port *port, int ch)
+{
+	if (!port->membase)
+		return;
+
+	while (!(rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK))
+		cpu_relax();
+
+	rda_uart_write(port, ch, RDA_UART_RXTX_BUFFER);
+}
+
+static void rda_uart_port_write(struct uart_port *port, const char *s,
+				u_int count)
+{
+	u32 old_irq_mask;
+	unsigned long flags;
+	int locked;
+
+	local_irq_save(flags);
+
+	if (port->sysrq) {
+		locked = 0;
+	} else if (oops_in_progress) {
+		locked = spin_trylock(&port->lock);
+	} else {
+		spin_lock(&port->lock);
+		locked = 1;
+	}
+
+	old_irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
+	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
+
+	uart_console_write(port, s, count, rda_console_putchar);
+
+	/* wait until all contents have been sent out */
+	while (!(rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK))
+		cpu_relax();
+
+	rda_uart_write(port, old_irq_mask, RDA_UART_IRQ_MASK);
+
+	if (locked)
+		spin_unlock(&port->lock);
+
+	local_irq_restore(flags);
+}
+
+static void rda_uart_console_write(struct console *co, const char *s,
+				   u_int count)
+{
+	struct rda_uart_port *rda_port;
+
+	rda_port = rda_uart_ports[co->index];
+	if (!rda_port)
+		return;
+
+	rda_uart_port_write(&rda_port->port, s, count);
+}
+
+static int rda_uart_console_setup(struct console *co, char *options)
+{
+	struct rda_uart_port *rda_port;
+	int baud = 921600;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index < 0 || co->index >= RDA_UART_PORT_NUM)
+		return -EINVAL;
+
+	rda_port = rda_uart_ports[co->index];
+	if (!rda_port || !rda_port->port.membase)
+		return -ENODEV;
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(&rda_port->port, co, baud, parity, bits, flow);
+}
+
+static struct console rda_uart_console = {
+	.name = RDA_UART_DEV_NAME,
+	.write = rda_uart_console_write,
+	.device = uart_console_device,
+	.setup = rda_uart_console_setup,
+	.flags = CON_PRINTBUFFER,
+	.index = -1,
+	.data = &rda_uart_driver,
+};
+
+static int __init rda_uart_console_init(void)
+{
+	register_console(&rda_uart_console);
+
+	return 0;
+}
+console_initcall(rda_uart_console_init);
+
+static void rda_uart_early_console_write(struct console *co,
+					 const char *s,
+					 u_int count)
+{
+	struct earlycon_device *dev = co->data;
+
+	rda_uart_port_write(&dev->port, s, count);
+}
+
+static int __init
+rda_uart_early_console_setup(struct earlycon_device *device, const char *opt)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = rda_uart_early_console_write;
+
+	return 0;
+}
+
+OF_EARLYCON_DECLARE(rda, "rda,8810pl-uart",
+		    rda_uart_early_console_setup);
+
+#define RDA_UART_CONSOLE (&rda_uart_console)
+#else
+#define RDA_UART_CONSOLE NULL
+#endif /* CONFIG_SERIAL_RDA_CONSOLE */
+
+static struct uart_driver rda_uart_driver = {
+	.owner = THIS_MODULE,
+	.driver_name = "rda-uart",
+	.dev_name = RDA_UART_DEV_NAME,
+	.nr = RDA_UART_PORT_NUM,
+	.cons = RDA_UART_CONSOLE,
+};
+
+static const struct of_device_id rda_uart_dt_matches[] = {
+	{ .compatible = "rda,8810pl-uart" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, rda_uart_dt_matches);
+
+static int rda_uart_probe(struct platform_device *pdev)
+{
+	struct resource *res_mem;
+	struct rda_uart_port *rda_port;
+	int ret, irq;
+
+	if (pdev->dev.of_node)
+		pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
+
+	if (pdev->id < 0 || pdev->id >= RDA_UART_PORT_NUM) {
+		dev_err(&pdev->dev, "id %d out of range\n", pdev->id);
+		return -EINVAL;
+	}
+
+	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res_mem) {
+		dev_err(&pdev->dev, "could not get mem\n");
+		return -ENODEV;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "could not get irq\n");
+		return irq;
+	}
+
+	if (rda_uart_ports[pdev->id]) {
+		dev_err(&pdev->dev, "port %d already allocated\n", pdev->id);
+		return -EBUSY;
+	}
+
+	rda_port = devm_kzalloc(&pdev->dev, sizeof(*rda_port), GFP_KERNEL);
+	if (!rda_port)
+		return -ENOMEM;
+
+	rda_port->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(rda_port->clk)) {
+		dev_err(&pdev->dev, "could not get clk\n");
+		return PTR_ERR(rda_port->clk);
+	}
+
+	rda_port->port.dev = &pdev->dev;
+	rda_port->port.regshift = 0;
+	rda_port->port.line = pdev->id;
+	rda_port->port.type = PORT_RDA;
+	rda_port->port.iotype = UPIO_MEM;
+	rda_port->port.mapbase = res_mem->start;
+	rda_port->port.irq = irq;
+	rda_port->port.uartclk = clk_get_rate(rda_port->clk);
+	if (rda_port->port.uartclk == 0) {
+		dev_err(&pdev->dev, "clock rate is zero\n");
+		return -EINVAL;
+	}
+	rda_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP |
+			       UPF_LOW_LATENCY;
+	rda_port->port.x_char = 0;
+	rda_port->port.fifosize = RDA_UART_TX_FIFO_SIZE;
+	rda_port->port.ops = &rda_uart_ops;
+
+	rda_uart_ports[pdev->id] = rda_port;
+	platform_set_drvdata(pdev, rda_port);
+
+	ret = uart_add_one_port(&rda_uart_driver, &rda_port->port);
+	if (ret)
+		rda_uart_ports[pdev->id] = NULL;
+
+	return ret;
+}
+
+static int rda_uart_remove(struct platform_device *pdev)
+{
+	struct rda_uart_port *rda_port = platform_get_drvdata(pdev);
+
+	uart_remove_one_port(&rda_uart_driver, &rda_port->port);
+	rda_uart_ports[pdev->id] = NULL;
+
+	return 0;
+}
+
+static struct platform_driver rda_uart_platform_driver = {
+	.probe = rda_uart_probe,
+	.remove = rda_uart_remove,
+	.driver = {
+		.name = "rda-uart",
+		.of_match_table = rda_uart_dt_matches,
+	},
+};
+
+static int __init rda_uart_init(void)
+{
+	int ret;
+
+	ret = uart_register_driver(&rda_uart_driver);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&rda_uart_platform_driver);
+	if (ret)
+		uart_unregister_driver(&rda_uart_driver);
+
+	return ret;
+}
+
+static void __init rda_uart_exit(void)
+{
+	platform_driver_unregister(&rda_uart_platform_driver);
+	uart_unregister_driver(&rda_uart_driver);
+}
+
+module_init(rda_uart_init);
+module_exit(rda_uart_exit);
+
+MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>");
+MODULE_DESCRIPTION("RDA8810PL serial device driver");
+MODULE_LICENSE("GPL");
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index dce5f9dae121..df4a7534e239 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -281,4 +281,7 @@
 /* MediaTek BTIF */
 #define PORT_MTK_BTIF	117
 
+/* RDA UART */
+#define PORT_RDA	118
+
 #endif /* _UAPILINUX_SERIAL_CORE_H */
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 11/11] MAINTAINERS: Add entry for RDA Micro SoC architecture
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: robh+dt, gregkh, jslaby, linux-unisoc, afaerber, linux-kernel,
	devicetree, linux-serial, amit.kucheria, linus.walleij,
	zhao_steven, Manivannan Sadhasivam

Add MAINTAINERS entry for RDA Micro SoC architecture with myself
as the maintainer.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 MAINTAINERS | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 3318f30903b2..da2149949fd7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1950,6 +1950,20 @@ M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 
+ARM/RDA MICRO ARCHITECTURE
+M:	Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L:	linux-unisoc@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	arch/arm/boot/dts/rda8810pl-*
+F:	drivers/clocksource/timer-rda.c
+F:	drivers/irqchip/irq-rda-intc.c
+F:	drivers/tty/serial/rda-uart.c
+F:	Documentation/devicetree/bindings/arm/rda.txt
+F:	Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt
+F:	Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
+F:	Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt
+
 ARM/REALTEK ARCHITECTURE
 M:	Andreas Färber <afaerber@suse.de>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 29+ messages in thread

* [PATCH v7 11/11] MAINTAINERS: Add entry for RDA Micro SoC architecture
@ 2018-12-18 15:02   ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2018-12-18 15:02 UTC (permalink / raw)
  To: olof, arnd, arm, linux-arm-kernel
  Cc: devicetree, gregkh, linus.walleij, Manivannan Sadhasivam,
	linux-kernel, amit.kucheria, linux-unisoc, robh+dt, linux-serial,
	jslaby, afaerber, zhao_steven

Add MAINTAINERS entry for RDA Micro SoC architecture with myself
as the maintainer.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
 MAINTAINERS | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 3318f30903b2..da2149949fd7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1950,6 +1950,20 @@ M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 
+ARM/RDA MICRO ARCHITECTURE
+M:	Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L:	linux-unisoc@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	arch/arm/boot/dts/rda8810pl-*
+F:	drivers/clocksource/timer-rda.c
+F:	drivers/irqchip/irq-rda-intc.c
+F:	drivers/tty/serial/rda-uart.c
+F:	Documentation/devicetree/bindings/arm/rda.txt
+F:	Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt
+F:	Documentation/devicetree/bindings/serial/rda,8810pl-uart.txt
+F:	Documentation/devicetree/bindings/timer/rda,8810pl-timer.txt
+
 ARM/REALTEK ARCHITECTURE
 M:	Andreas Färber <afaerber@suse.de>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 29+ messages in thread

* Re: [PATCH v7 00/11] Add initial RDA8810PL SoC and Orange Pi boards support
  2018-12-18 15:02 ` Manivannan Sadhasivam
@ 2018-12-31 21:13   ` Olof Johansson
  -1 siblings, 0 replies; 29+ messages in thread
From: Olof Johansson @ 2018-12-31 21:13 UTC (permalink / raw)
  To: Manivannan Sadhasivam
  Cc: arnd, arm, linux-arm-kernel, robh+dt, gregkh, jslaby,
	linux-unisoc, afaerber, linux-kernel, devicetree, linux-serial,
	amit.kucheria, linus.walleij, zhao_steven

On Tue, Dec 18, 2018 at 08:32:27PM +0530, Manivannan Sadhasivam wrote:
> Hello Maintainers,
> 
> This patch series adds initial RDA8810PL SoC and Orange Pi boards (2G IoT and
> i96) support. RDA8810PL is an ARM Cortex A5 based SoC with Vivante's GC860
> GPU. The SoC has been added as a new ARM sub architecture with myself as the
> maintainer.
> 
> More information about the boards can be found in below links:
> 
> 1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
> 2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/
> 
> All patches are reviewed by the corresponding subsystem maintainers. The
> clocksource and irqchip patches are reviewed and merged while the serial
> driver got review from Greg but I'm not sure who will apply it.
> 
> So as per my discussion with Arnd, sending the individual patches instead
> of a Pull request so that the rest of the patches can go through the
> ARM SoC tree.
> 
> Please consider applying it.

Hi,

I've applied this series to our next/late branch. It's a branch we'll try to
get merged by the end of the merge window, but it's not a guarantee that we'll
be able to get it done. If not, the material will be moved to the next release
instead.


Thanks!


-Olof

^ permalink raw reply	[flat|nested] 29+ messages in thread

* Re: [PATCH v7 00/11] Add initial RDA8810PL SoC and Orange Pi boards support
@ 2018-12-31 21:13   ` Olof Johansson
  0 siblings, 0 replies; 29+ messages in thread
From: Olof Johansson @ 2018-12-31 21:13 UTC (permalink / raw)
  To: Manivannan Sadhasivam
  Cc: devicetree, arm, arnd, gregkh, linus.walleij, linux-kernel,
	amit.kucheria, linux-unisoc, robh+dt, linux-serial, jslaby,
	afaerber, linux-arm-kernel, zhao_steven

On Tue, Dec 18, 2018 at 08:32:27PM +0530, Manivannan Sadhasivam wrote:
> Hello Maintainers,
> 
> This patch series adds initial RDA8810PL SoC and Orange Pi boards (2G IoT and
> i96) support. RDA8810PL is an ARM Cortex A5 based SoC with Vivante's GC860
> GPU. The SoC has been added as a new ARM sub architecture with myself as the
> maintainer.
> 
> More information about the boards can be found in below links:
> 
> 1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
> 2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/
> 
> All patches are reviewed by the corresponding subsystem maintainers. The
> clocksource and irqchip patches are reviewed and merged while the serial
> driver got review from Greg but I'm not sure who will apply it.
> 
> So as per my discussion with Arnd, sending the individual patches instead
> of a Pull request so that the rest of the patches can go through the
> ARM SoC tree.
> 
> Please consider applying it.

Hi,

I've applied this series to our next/late branch. It's a branch we'll try to
get merged by the end of the merge window, but it's not a guarantee that we'll
be able to get it done. If not, the material will be moved to the next release
instead.


Thanks!


-Olof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 29+ messages in thread

* Re: [PATCH v7 00/11] Add initial RDA8810PL SoC and Orange Pi boards support
  2018-12-31 21:13   ` Olof Johansson
  (?)
@ 2019-01-01  3:02     ` Manivannan Sadhasivam
  -1 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2019-01-01  3:02 UTC (permalink / raw)
  To: Olof Johansson
  Cc: arnd, arm, linux-arm-kernel, robh+dt, gregkh, jslaby,
	linux-unisoc, afaerber, linux-kernel, devicetree, linux-serial,
	amit.kucheria, linus.walleij, zhao_steven

Hi Olof,

On Mon, Dec 31, 2018 at 01:13:42PM -0800, Olof Johansson wrote:
> On Tue, Dec 18, 2018 at 08:32:27PM +0530, Manivannan Sadhasivam wrote:
> > Hello Maintainers,
> > 
> > This patch series adds initial RDA8810PL SoC and Orange Pi boards (2G IoT and
> > i96) support. RDA8810PL is an ARM Cortex A5 based SoC with Vivante's GC860
> > GPU. The SoC has been added as a new ARM sub architecture with myself as the
> > maintainer.
> > 
> > More information about the boards can be found in below links:
> > 
> > 1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
> > 2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/
> > 
> > All patches are reviewed by the corresponding subsystem maintainers. The
> > clocksource and irqchip patches are reviewed and merged while the serial
> > driver got review from Greg but I'm not sure who will apply it.
> > 
> > So as per my discussion with Arnd, sending the individual patches instead
> > of a Pull request so that the rest of the patches can go through the
> > ARM SoC tree.
> > 
> > Please consider applying it.
> 
> Hi,
> 
> I've applied this series to our next/late branch. It's a branch we'll try to
> get merged by the end of the merge window, but it's not a guarantee that we'll
> be able to get it done. If not, the material will be moved to the next release
> instead.
>

Okay, thanks for the update!

Regards,
Mani

> 
> Thanks!
> 
> 
> -Olof

^ permalink raw reply	[flat|nested] 29+ messages in thread

* Re: [PATCH v7 00/11] Add initial RDA8810PL SoC and Orange Pi boards support
@ 2019-01-01  3:02     ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2019-01-01  3:02 UTC (permalink / raw)
  To: Olof Johansson
  Cc: devicetree, arm, arnd, gregkh, linus.walleij, linux-kernel,
	amit.kucheria, linux-unisoc, robh+dt, linux-serial, jslaby,
	afaerber, linux-arm-kernel, zhao_steven

Hi Olof,

On Mon, Dec 31, 2018 at 01:13:42PM -0800, Olof Johansson wrote:
> On Tue, Dec 18, 2018 at 08:32:27PM +0530, Manivannan Sadhasivam wrote:
> > Hello Maintainers,
> > 
> > This patch series adds initial RDA8810PL SoC and Orange Pi boards (2G IoT and
> > i96) support. RDA8810PL is an ARM Cortex A5 based SoC with Vivante's GC860
> > GPU. The SoC has been added as a new ARM sub architecture with myself as the
> > maintainer.
> > 
> > More information about the boards can be found in below links:
> > 
> > 1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
> > 2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/
> > 
> > All patches are reviewed by the corresponding subsystem maintainers. The
> > clocksource and irqchip patches are reviewed and merged while the serial
> > driver got review from Greg but I'm not sure who will apply it.
> > 
> > So as per my discussion with Arnd, sending the individual patches instead
> > of a Pull request so that the rest of the patches can go through the
> > ARM SoC tree.
> > 
> > Please consider applying it.
> 
> Hi,
> 
> I've applied this series to our next/late branch. It's a branch we'll try to
> get merged by the end of the merge window, but it's not a guarantee that we'll
> be able to get it done. If not, the material will be moved to the next release
> instead.
>

Okay, thanks for the update!

Regards,
Mani

> 
> Thanks!
> 
> 
> -Olof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 29+ messages in thread

* Re: [PATCH v7 00/11] Add initial RDA8810PL SoC and Orange Pi boards support
@ 2019-01-01  3:02     ` Manivannan Sadhasivam
  0 siblings, 0 replies; 29+ messages in thread
From: Manivannan Sadhasivam @ 2019-01-01  3:02 UTC (permalink / raw)
  To: Olof Johansson
  Cc: devicetree, arm, arnd, gregkh, linus.walleij, linux-kernel,
	amit.kucheria, linux-unisoc, robh+dt, linux-serial, jslaby,
	afaerber, linux-arm-kernel, zhao_steven

Hi Olof,

On Mon, Dec 31, 2018 at 01:13:42PM -0800, Olof Johansson wrote:
> On Tue, Dec 18, 2018 at 08:32:27PM +0530, Manivannan Sadhasivam wrote:
> > Hello Maintainers,
> > 
> > This patch series adds initial RDA8810PL SoC and Orange Pi boards (2G IoT and
> > i96) support. RDA8810PL is an ARM Cortex A5 based SoC with Vivante's GC860
> > GPU. The SoC has been added as a new ARM sub architecture with myself as the
> > maintainer.
> > 
> > More information about the boards can be found in below links:
> > 
> > 1. Orange Pi 2G-IoT - http://www.orangepi.org/OrangePi2GIOT/
> > 2. Orange Pi i96 - https://www.96boards.org/product/orangepi-i96/
> > 
> > All patches are reviewed by the corresponding subsystem maintainers. The
> > clocksource and irqchip patches are reviewed and merged while the serial
> > driver got review from Greg but I'm not sure who will apply it.
> > 
> > So as per my discussion with Arnd, sending the individual patches instead
> > of a Pull request so that the rest of the patches can go through the
> > ARM SoC tree.
> > 
> > Please consider applying it.
> 
> Hi,
> 
> I've applied this series to our next/late branch. It's a branch we'll try to
> get merged by the end of the merge window, but it's not a guarantee that we'll
> be able to get it done. If not, the material will be moved to the next release
> instead.
>

Okay, thanks for the update!

Regards,
Mani

> 
> Thanks!
> 
> 
> -Olof

^ permalink raw reply	[flat|nested] 29+ messages in thread

end of thread, other threads:[~2019-01-01  3:03 UTC | newest]

Thread overview: 29+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-12-18 15:02 [PATCH v7 00/11] Add initial RDA8810PL SoC and Orange Pi boards support Manivannan Sadhasivam
2018-12-18 15:02 ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 01/11] dt-bindings: Add RDA Micro vendor prefix Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 02/11] dt-bindings: arm: Document RDA8810PL and reference boards Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 03/11] ARM: Prepare RDA8810PL SoC Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 04/11] ARM: dts: Add devicetree for " Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 05/11] ARM: dts: Add devicetree for OrangePi 2G IoT board Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 06/11] ARM: dts: Add devicetree for OrangePi i96 board Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 07/11] ARM: dts: rda8810pl: Add timer support Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 08/11] dt-bindings: serial: Document RDA Micro UART Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 09/11] ARM: dts: rda8810pl: Add interrupt support for UART Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 10/11] tty: serial: Add RDA8810PL UART driver Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-18 15:02 ` [PATCH v7 11/11] MAINTAINERS: Add entry for RDA Micro SoC architecture Manivannan Sadhasivam
2018-12-18 15:02   ` Manivannan Sadhasivam
2018-12-31 21:13 ` [PATCH v7 00/11] Add initial RDA8810PL SoC and Orange Pi boards support Olof Johansson
2018-12-31 21:13   ` Olof Johansson
2019-01-01  3:02   ` Manivannan Sadhasivam
2019-01-01  3:02     ` Manivannan Sadhasivam
2019-01-01  3:02     ` Manivannan Sadhasivam

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.