* [PATCH v2 0/6] arm64: dts: DB820c: Add display and audio support
@ 2019-01-30 11:04 ` Srinivas Kandagatla
0 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: linux-arm-msm, Srinivas Kandagatla, linux-arm-kernel, devicetree
Hi Andy,
Now that most of the bits are in mainline, its good time to add display
and audio support to DB820c.
These patches are being tested in integration branch from long time.
Am resending 2 SMMU patches (https://patchwork.kernel.org/cover/10726329/)
in this series to keep all the display and sound patches together.
Can you pick these up for 5.1
thanks,
srini
Changes since v1:
- GPU node updated by Jordan.
- deleted extra lines from sound card dt patch
Archit Taneja (3):
arm64: dts: msm8996: Add display smmu node
arm64: qcom: msm8996.dtsi: Add Display nodes
arm64: dts: apq8096-db820c: Add HDMI display support
Jordan Crouse (2):
arm64: dts: msm8996: Add graphics smmu node
arm64: dts: Add Adreno GPU definitions
Srinivas Kandagatla (1):
arm64: dts: db820c: Add sound card support
.../boot/dts/qcom/apq8096-db820c-pins.dtsi | 52 +++
.../dts/qcom/apq8096-db820c-pmic-pins.dtsi | 8 +
arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 121 ++++++
arch/arm64/boot/dts/qcom/msm8996-pins.dtsi | 43 ++
arch/arm64/boot/dts/qcom/msm8996.dtsi | 380 ++++++++++++++++++
5 files changed, 604 insertions(+)
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2 1/6] arm64: dts: msm8996: Add graphics smmu node
2019-01-30 11:04 ` Srinivas Kandagatla
@ 2019-01-30 11:04 ` Srinivas Kandagatla
-1 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: devicetree, linux-arm-msm, Jordan Crouse, Srinivas Kandagatla,
Vivek Gautam, linux-arm-kernel
From: Jordan Crouse <jcrouse@codeaurora.org>
Add device node for graphics smmu, aka. adreno_smmu.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 6ba96916c66d..c9b80d175fd4 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1138,6 +1138,23 @@
};
};
+ adreno_smmu: arm,smmu@b40000 {
+ compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
+ reg = <0xb40000 0x10000>;
+
+ #global-interrupts = <1>;
+ interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
+ #iommu-cells = <1>;
+
+ clocks = <&mmcc GPU_AHB_CLK>,
+ <&gcc GCC_MMSS_BIMC_GFX_CLK>;
+ clock-names = "iface", "bus";
+
+ power-domains = <&mmcc GPU_GDSC>;
+ };
+
agnoc@0 {
power-domains = <&gcc AGGRE0_NOC_GDSC>;
compatible = "simple-pm-bus";
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v2 1/6] arm64: dts: msm8996: Add graphics smmu node
@ 2019-01-30 11:04 ` Srinivas Kandagatla
0 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: devicetree, linux-arm-msm, Jordan Crouse, Srinivas Kandagatla,
Vivek Gautam, linux-arm-kernel
From: Jordan Crouse <jcrouse@codeaurora.org>
Add device node for graphics smmu, aka. adreno_smmu.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 6ba96916c66d..c9b80d175fd4 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1138,6 +1138,23 @@
};
};
+ adreno_smmu: arm,smmu@b40000 {
+ compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
+ reg = <0xb40000 0x10000>;
+
+ #global-interrupts = <1>;
+ interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
+ #iommu-cells = <1>;
+
+ clocks = <&mmcc GPU_AHB_CLK>,
+ <&gcc GCC_MMSS_BIMC_GFX_CLK>;
+ clock-names = "iface", "bus";
+
+ power-domains = <&mmcc GPU_GDSC>;
+ };
+
agnoc@0 {
power-domains = <&gcc AGGRE0_NOC_GDSC>;
compatible = "simple-pm-bus";
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 2/6] arm64: dts: msm8996: Add display smmu node
2019-01-30 11:04 ` Srinivas Kandagatla
@ 2019-01-30 11:04 ` Srinivas Kandagatla
-1 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: devicetree, Archit Taneja, linux-arm-msm, Srinivas Kandagatla,
Vivek Gautam, linux-arm-kernel
From: Archit Taneja <architt@codeaurora.org>
Add device node for display smmu, aka. mdp_smmu.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index c9b80d175fd4..96adda520bd5 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1155,6 +1155,23 @@
power-domains = <&mmcc GPU_GDSC>;
};
+ mdp_smmu: arm,smmu@d00000 {
+ compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
+ reg = <0xd00000 0x10000>;
+
+ #global-interrupts = <1>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>;
+ #iommu-cells = <1>;
+
+ clocks = <&mmcc SMMU_MDP_AHB_CLK>,
+ <&mmcc SMMU_MDP_AXI_CLK>;
+ clock-names = "iface", "bus";
+
+ power-domains = <&mmcc MDSS_GDSC>;
+ };
+
agnoc@0 {
power-domains = <&gcc AGGRE0_NOC_GDSC>;
compatible = "simple-pm-bus";
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v2 2/6] arm64: dts: msm8996: Add display smmu node
@ 2019-01-30 11:04 ` Srinivas Kandagatla
0 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: devicetree, Archit Taneja, linux-arm-msm, Srinivas Kandagatla,
Vivek Gautam, linux-arm-kernel
From: Archit Taneja <architt@codeaurora.org>
Add device node for display smmu, aka. mdp_smmu.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index c9b80d175fd4..96adda520bd5 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1155,6 +1155,23 @@
power-domains = <&mmcc GPU_GDSC>;
};
+ mdp_smmu: arm,smmu@d00000 {
+ compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
+ reg = <0xd00000 0x10000>;
+
+ #global-interrupts = <1>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>;
+ #iommu-cells = <1>;
+
+ clocks = <&mmcc SMMU_MDP_AHB_CLK>,
+ <&mmcc SMMU_MDP_AXI_CLK>;
+ clock-names = "iface", "bus";
+
+ power-domains = <&mmcc MDSS_GDSC>;
+ };
+
agnoc@0 {
power-domains = <&gcc AGGRE0_NOC_GDSC>;
compatible = "simple-pm-bus";
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 3/6] arm64: qcom: msm8996.dtsi: Add Display nodes
2019-01-30 11:04 ` Srinivas Kandagatla
@ 2019-01-30 11:04 ` Srinivas Kandagatla
-1 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: devicetree, Archit Taneja, linux-arm-msm, Srinivas Kandagatla,
Vivek Gautam, linux-arm-kernel
From: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
[Removed instances of mmagic clocks;
Use qcom,msm8996-smmu-v2 bindings]
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 120 ++++++++++++++++++++++++++
1 file changed, 120 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 96adda520bd5..0d0b9482aa4d 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1337,6 +1337,126 @@
"bus_slave";
};
};
+
+ mdss: mdss@900000 {
+ compatible = "qcom,mdss";
+
+ reg = <0x900000 0x1000>,
+ <0x9b0000 0x1040>,
+ <0x9b8000 0x1040>;
+ reg-names = "mdss_phys",
+ "vbif_phys",
+ "vbif_nrt_phys";
+
+ power-domains = <&mmcc MDSS_GDSC>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>;
+ clock-names = "iface_clk";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mdp: mdp@901000 {
+ compatible = "qcom,mdp5";
+ reg = <0x901000 0x90000>;
+ reg-names = "mdp_phys";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_MDP_CLK>,
+ <&mmcc SMMU_MDP_AXI_CLK>,
+ <&mmcc MDSS_VSYNC_CLK>;
+ clock-names = "iface_clk",
+ "bus_clk",
+ "core_clk",
+ "iommu_clk",
+ "vsync_clk";
+
+ iommus = <&mdp_smmu 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdp5_intf3_out: endpoint {
+ remote-endpoint = <&hdmi_in>;
+ };
+ };
+ };
+ };
+
+ hdmi: hdmi-tx@9a0000 {
+ compatible = "qcom,hdmi-tx-8996";
+ reg = <0x009a0000 0x50c>,
+ <0x00070000 0x6158>,
+ <0x009e0000 0xfff>;
+ reg-names = "core_physical",
+ "qfprom_physical",
+ "hdcp_physical";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&mmcc MDSS_MDP_CLK>,
+ <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_HDMI_CLK>,
+ <&mmcc MDSS_HDMI_AHB_CLK>,
+ <&mmcc MDSS_EXTPCLK_CLK>;
+ clock-names =
+ "mdp_core_clk",
+ "iface_clk",
+ "core_clk",
+ "alt_iface_clk",
+ "extp_clk";
+
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi_phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ hdmi_in: endpoint {
+ remote-endpoint = <&mdp5_intf3_out>;
+ };
+ };
+ };
+ };
+
+ hdmi_phy: hdmi-phy@9a0600 {
+ #phy-cells = <0>;
+ compatible = "qcom,hdmi-phy-8996";
+ reg = <0x9a0600 0x1c4>,
+ <0x9a0a00 0x124>,
+ <0x9a0c00 0x124>,
+ <0x9a0e00 0x124>,
+ <0x9a1000 0x124>,
+ <0x9a1200 0x0c8>;
+ reg-names = "hdmi_pll",
+ "hdmi_tx_l0",
+ "hdmi_tx_l1",
+ "hdmi_tx_l2",
+ "hdmi_tx_l3",
+ "hdmi_phy";
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&gcc GCC_HDMI_CLKREF_CLK>;
+ clock-names = "iface_clk",
+ "ref_clk";
+ };
+ };
};
adsp-pil {
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v2 3/6] arm64: qcom: msm8996.dtsi: Add Display nodes
@ 2019-01-30 11:04 ` Srinivas Kandagatla
0 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: devicetree, Archit Taneja, linux-arm-msm, Srinivas Kandagatla,
Vivek Gautam, linux-arm-kernel
From: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
[Removed instances of mmagic clocks;
Use qcom,msm8996-smmu-v2 bindings]
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 120 ++++++++++++++++++++++++++
1 file changed, 120 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 96adda520bd5..0d0b9482aa4d 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1337,6 +1337,126 @@
"bus_slave";
};
};
+
+ mdss: mdss@900000 {
+ compatible = "qcom,mdss";
+
+ reg = <0x900000 0x1000>,
+ <0x9b0000 0x1040>,
+ <0x9b8000 0x1040>;
+ reg-names = "mdss_phys",
+ "vbif_phys",
+ "vbif_nrt_phys";
+
+ power-domains = <&mmcc MDSS_GDSC>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>;
+ clock-names = "iface_clk";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mdp: mdp@901000 {
+ compatible = "qcom,mdp5";
+ reg = <0x901000 0x90000>;
+ reg-names = "mdp_phys";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_MDP_CLK>,
+ <&mmcc SMMU_MDP_AXI_CLK>,
+ <&mmcc MDSS_VSYNC_CLK>;
+ clock-names = "iface_clk",
+ "bus_clk",
+ "core_clk",
+ "iommu_clk",
+ "vsync_clk";
+
+ iommus = <&mdp_smmu 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdp5_intf3_out: endpoint {
+ remote-endpoint = <&hdmi_in>;
+ };
+ };
+ };
+ };
+
+ hdmi: hdmi-tx@9a0000 {
+ compatible = "qcom,hdmi-tx-8996";
+ reg = <0x009a0000 0x50c>,
+ <0x00070000 0x6158>,
+ <0x009e0000 0xfff>;
+ reg-names = "core_physical",
+ "qfprom_physical",
+ "hdcp_physical";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&mmcc MDSS_MDP_CLK>,
+ <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_HDMI_CLK>,
+ <&mmcc MDSS_HDMI_AHB_CLK>,
+ <&mmcc MDSS_EXTPCLK_CLK>;
+ clock-names =
+ "mdp_core_clk",
+ "iface_clk",
+ "core_clk",
+ "alt_iface_clk",
+ "extp_clk";
+
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi_phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ hdmi_in: endpoint {
+ remote-endpoint = <&mdp5_intf3_out>;
+ };
+ };
+ };
+ };
+
+ hdmi_phy: hdmi-phy@9a0600 {
+ #phy-cells = <0>;
+ compatible = "qcom,hdmi-phy-8996";
+ reg = <0x9a0600 0x1c4>,
+ <0x9a0a00 0x124>,
+ <0x9a0c00 0x124>,
+ <0x9a0e00 0x124>,
+ <0x9a1000 0x124>,
+ <0x9a1200 0x0c8>;
+ reg-names = "hdmi_pll",
+ "hdmi_tx_l0",
+ "hdmi_tx_l1",
+ "hdmi_tx_l2",
+ "hdmi_tx_l3",
+ "hdmi_phy";
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&gcc GCC_HDMI_CLKREF_CLK>;
+ clock-names = "iface_clk",
+ "ref_clk";
+ };
+ };
};
adsp-pil {
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 4/6] arm64: dts: Add Adreno GPU definitions
2019-01-30 11:04 ` Srinivas Kandagatla
@ 2019-01-30 11:04 ` Srinivas Kandagatla
-1 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: devicetree, linux-arm-msm, Jordan Crouse, Srinivas Kandagatla,
Vivek Gautam, linux-arm-kernel
From: Jordan Crouse <jcrouse@codeaurora.org>
Add an initial node for the Adreno GPU.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 86 +++++++++++++++++++++++++++
1 file changed, 86 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 0d0b9482aa4d..095041589954 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -84,6 +84,12 @@
qcom,client-id = <1>;
qcom,vmid = <15>;
};
+
+ zap_shader_region: gpu@8f200000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x90b00000 0x0 0xa00000>;
+ no-map;
+ };
};
cpus {
@@ -796,6 +802,11 @@
reg = <0x24f 0x1>;
bits = <1 4>;
};
+
+ gpu_speed_bin: gpu_speed_bin@133 {
+ reg = <0x133 0x1>;
+ bits = <5 3>;
+ };
};
phy@34000 {
@@ -1338,6 +1349,81 @@
};
};
+ gpu@b00000 {
+ compatible = "qcom,adreno-530.2", "qcom,adreno";
+ #stream-id-cells = <16>;
+
+ reg = <0xb00000 0x3f000>;
+ reg-names = "kgsl_3d0_reg_memory";
+
+ interrupts = <0 300 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&mmcc GPU_GX_GFX3D_CLK>,
+ <&mmcc GPU_AHB_CLK>,
+ <&mmcc GPU_GX_RBBMTIMER_CLK>,
+ <&gcc GCC_BIMC_GFX_CLK>,
+ <&gcc GCC_MMSS_BIMC_GFX_CLK>;
+
+ clock-names = "core",
+ "iface",
+ "rbbmtimer",
+ "mem",
+ "mem_iface";
+
+ power-domains = <&mmcc GPU_GDSC>;
+ iommus = <&adreno_smmu 0>;
+
+ nvmem-cells = <&gpu_speed_bin>;
+ nvmem-cell-names = "speed_bin";
+
+ qcom,gpu-quirk-two-pass-use-wfi;
+ qcom,gpu-quirk-fault-detect-mask;
+
+ operating-points-v2 = <&gpu_opp_table>;
+
+ gpu_opp_table: opp-table {
+ compatible ="operating-points-v2";
+
+ /*
+ * 624Mhz and 560Mhz are only available on speed
+ * bin (1 << 0). All the rest are available on
+ * all bins of the hardware
+ */
+ opp-624000000 {
+ opp-hz = /bits/ 64 <624000000>;
+ opp-supported-hw = <0x01>;
+ };
+ opp-560000000 {
+ opp-hz = /bits/ 64 <560000000>;
+ opp-supported-hw = <0x01>;
+ };
+ opp-510000000 {
+ opp-hz = /bits/ 64 <510000000>;
+ opp-supported-hw = <0xFF>;
+ };
+ opp-401800000 {
+ opp-hz = /bits/ 64 <401800000>;
+ opp-supported-hw = <0xFF>;
+ };
+ opp-315000000 {
+ opp-hz = /bits/ 64 <315000000>;
+ opp-supported-hw = <0xFF>;
+ };
+ opp-214000000 {
+ opp-hz = /bits/ 64 <214000000>;
+ opp-supported-hw = <0xFF>;
+ };
+ opp-133000000 {
+ opp-hz = /bits/ 64 <133000000>;
+ opp-supported-hw = <0xFF>;
+ };
+ };
+
+ zap-shader {
+ memory-region = <&zap_shader_region>;
+ };
+ };
+
mdss: mdss@900000 {
compatible = "qcom,mdss";
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v2 4/6] arm64: dts: Add Adreno GPU definitions
@ 2019-01-30 11:04 ` Srinivas Kandagatla
0 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: devicetree, linux-arm-msm, Jordan Crouse, Srinivas Kandagatla,
Vivek Gautam, linux-arm-kernel
From: Jordan Crouse <jcrouse@codeaurora.org>
Add an initial node for the Adreno GPU.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 86 +++++++++++++++++++++++++++
1 file changed, 86 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 0d0b9482aa4d..095041589954 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -84,6 +84,12 @@
qcom,client-id = <1>;
qcom,vmid = <15>;
};
+
+ zap_shader_region: gpu@8f200000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x90b00000 0x0 0xa00000>;
+ no-map;
+ };
};
cpus {
@@ -796,6 +802,11 @@
reg = <0x24f 0x1>;
bits = <1 4>;
};
+
+ gpu_speed_bin: gpu_speed_bin@133 {
+ reg = <0x133 0x1>;
+ bits = <5 3>;
+ };
};
phy@34000 {
@@ -1338,6 +1349,81 @@
};
};
+ gpu@b00000 {
+ compatible = "qcom,adreno-530.2", "qcom,adreno";
+ #stream-id-cells = <16>;
+
+ reg = <0xb00000 0x3f000>;
+ reg-names = "kgsl_3d0_reg_memory";
+
+ interrupts = <0 300 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&mmcc GPU_GX_GFX3D_CLK>,
+ <&mmcc GPU_AHB_CLK>,
+ <&mmcc GPU_GX_RBBMTIMER_CLK>,
+ <&gcc GCC_BIMC_GFX_CLK>,
+ <&gcc GCC_MMSS_BIMC_GFX_CLK>;
+
+ clock-names = "core",
+ "iface",
+ "rbbmtimer",
+ "mem",
+ "mem_iface";
+
+ power-domains = <&mmcc GPU_GDSC>;
+ iommus = <&adreno_smmu 0>;
+
+ nvmem-cells = <&gpu_speed_bin>;
+ nvmem-cell-names = "speed_bin";
+
+ qcom,gpu-quirk-two-pass-use-wfi;
+ qcom,gpu-quirk-fault-detect-mask;
+
+ operating-points-v2 = <&gpu_opp_table>;
+
+ gpu_opp_table: opp-table {
+ compatible ="operating-points-v2";
+
+ /*
+ * 624Mhz and 560Mhz are only available on speed
+ * bin (1 << 0). All the rest are available on
+ * all bins of the hardware
+ */
+ opp-624000000 {
+ opp-hz = /bits/ 64 <624000000>;
+ opp-supported-hw = <0x01>;
+ };
+ opp-560000000 {
+ opp-hz = /bits/ 64 <560000000>;
+ opp-supported-hw = <0x01>;
+ };
+ opp-510000000 {
+ opp-hz = /bits/ 64 <510000000>;
+ opp-supported-hw = <0xFF>;
+ };
+ opp-401800000 {
+ opp-hz = /bits/ 64 <401800000>;
+ opp-supported-hw = <0xFF>;
+ };
+ opp-315000000 {
+ opp-hz = /bits/ 64 <315000000>;
+ opp-supported-hw = <0xFF>;
+ };
+ opp-214000000 {
+ opp-hz = /bits/ 64 <214000000>;
+ opp-supported-hw = <0xFF>;
+ };
+ opp-133000000 {
+ opp-hz = /bits/ 64 <133000000>;
+ opp-supported-hw = <0xFF>;
+ };
+ };
+
+ zap-shader {
+ memory-region = <&zap_shader_region>;
+ };
+ };
+
mdss: mdss@900000 {
compatible = "qcom,mdss";
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 5/6] arm64: dts: apq8096-db820c: Add HDMI display support
2019-01-30 11:04 ` Srinivas Kandagatla
@ 2019-01-30 11:04 ` Srinivas Kandagatla
-1 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: linux-arm-msm, Archit Taneja, Srinivas Kandagatla,
linux-arm-kernel, devicetree
From: Archit Taneja <architt@codeaurora.org>
The APQ8096 DB820c platform provides HDMI output. The MDSS block on
8x96 supports a direct HDMI out. Populate the MDSS, MDP and HDMI DT
nodes. Also, add the HDMI HPD and DDC pinctrl nodes with the bias
and driver strength specified for this platform.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
.../boot/dts/qcom/apq8096-db820c-pins.dtsi | 52 +++++++++++++++++++
arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 27 ++++++++++
2 files changed, 79 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi
index 6a573875d45a..1c0d06f59d00 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi
@@ -62,4 +62,56 @@
bias-disable;
};
};
+
+ hdmi_hpd_active: hdmi_hpd_active {
+ mux {
+ pins = "gpio34";
+ function = "hdmi_hot";
+ };
+
+ config {
+ pins = "gpio34";
+ bias-pull-down;
+ drive-strength = <16>;
+ };
+ };
+
+ hdmi_hpd_suspend: hdmi_hpd_suspend {
+ mux {
+ pins = "gpio34";
+ function = "hdmi_hot";
+ };
+
+ config {
+ pins = "gpio34";
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+ };
+
+ hdmi_ddc_active: hdmi_ddc_active {
+ mux {
+ pins = "gpio32", "gpio33";
+ function = "hdmi_ddc";
+ };
+
+ config {
+ pins = "gpio32", "gpio33";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ hdmi_ddc_suspend: hdmi_ddc_suspend {
+ mux {
+ pins = "gpio32", "gpio33";
+ function = "hdmi_ddc";
+ };
+
+ config {
+ pins = "gpio32", "gpio33";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
};
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index 6d50449fbcdf..1e78f0b47c89 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -452,6 +452,33 @@
perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
};
};
+
+ mdss@900000 {
+ status = "okay";
+
+ mdp@901000 {
+ status = "okay";
+ };
+
+ hdmi-phy@9a0600 {
+ status = "okay";
+
+ vddio-supply = <&pm8994_l12>;
+ vcca-supply = <&pm8994_l28>;
+ #phy-cells = <0>;
+ };
+
+ hdmi-tx@9a0000 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
+ pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
+
+ core-vdda-supply = <&pm8994_l12>;
+ core-vcc-supply = <&pm8994_s4>;
+ };
+ };
};
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v2 5/6] arm64: dts: apq8096-db820c: Add HDMI display support
@ 2019-01-30 11:04 ` Srinivas Kandagatla
0 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: linux-arm-msm, Archit Taneja, Srinivas Kandagatla,
linux-arm-kernel, devicetree
From: Archit Taneja <architt@codeaurora.org>
The APQ8096 DB820c platform provides HDMI output. The MDSS block on
8x96 supports a direct HDMI out. Populate the MDSS, MDP and HDMI DT
nodes. Also, add the HDMI HPD and DDC pinctrl nodes with the bias
and driver strength specified for this platform.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
.../boot/dts/qcom/apq8096-db820c-pins.dtsi | 52 +++++++++++++++++++
arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 27 ++++++++++
2 files changed, 79 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi
index 6a573875d45a..1c0d06f59d00 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi
@@ -62,4 +62,56 @@
bias-disable;
};
};
+
+ hdmi_hpd_active: hdmi_hpd_active {
+ mux {
+ pins = "gpio34";
+ function = "hdmi_hot";
+ };
+
+ config {
+ pins = "gpio34";
+ bias-pull-down;
+ drive-strength = <16>;
+ };
+ };
+
+ hdmi_hpd_suspend: hdmi_hpd_suspend {
+ mux {
+ pins = "gpio34";
+ function = "hdmi_hot";
+ };
+
+ config {
+ pins = "gpio34";
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+ };
+
+ hdmi_ddc_active: hdmi_ddc_active {
+ mux {
+ pins = "gpio32", "gpio33";
+ function = "hdmi_ddc";
+ };
+
+ config {
+ pins = "gpio32", "gpio33";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ hdmi_ddc_suspend: hdmi_ddc_suspend {
+ mux {
+ pins = "gpio32", "gpio33";
+ function = "hdmi_ddc";
+ };
+
+ config {
+ pins = "gpio32", "gpio33";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
};
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index 6d50449fbcdf..1e78f0b47c89 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -452,6 +452,33 @@
perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
};
};
+
+ mdss@900000 {
+ status = "okay";
+
+ mdp@901000 {
+ status = "okay";
+ };
+
+ hdmi-phy@9a0600 {
+ status = "okay";
+
+ vddio-supply = <&pm8994_l12>;
+ vcca-supply = <&pm8994_l28>;
+ #phy-cells = <0>;
+ };
+
+ hdmi-tx@9a0000 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
+ pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
+
+ core-vdda-supply = <&pm8994_l12>;
+ core-vcc-supply = <&pm8994_s4>;
+ };
+ };
};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 6/6] arm64: dts: db820c: Add sound card support
2019-01-30 11:04 ` Srinivas Kandagatla
@ 2019-01-30 11:04 ` Srinivas Kandagatla
-1 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: linux-arm-msm, Srinivas Kandagatla, linux-arm-kernel, devicetree
This patch adds support both digital and analog audio on DB820c.
This board has HDMI port and 3.5mm audio jack to support both digital
and analog audio respectively.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
.../dts/qcom/apq8096-db820c-pmic-pins.dtsi | 8 +
arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 94 ++++++++++++
arch/arm64/boot/dts/qcom/msm8996-pins.dtsi | 43 ++++++
arch/arm64/boot/dts/qcom/msm8996.dtsi | 140 ++++++++++++++++++
4 files changed, 285 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi
index a6ad3d7fe655..31a3e3311ad5 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi
@@ -36,6 +36,14 @@
};
};
+ audio_mclk: clk_div1 {
+ pinconf {
+ pins = "gpio15";
+ function = "func1";
+ power-source = <PM8994_GPIO_S4>; // 1.8V
+ };
+ };
+
volume_up_gpio: pm8996_gpio2 {
pinconf {
pins = "gpio2";
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index 1e78f0b47c89..7f4a8a08a029 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -18,6 +18,8 @@
#include "apq8096-db820c-pmic-pins.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
/*
* GPIO name legend: proper name = the GPIO line is used as GPIO
@@ -63,6 +65,7 @@
};
clocks {
+ compatible = "simple-bus";
divclk4: divclk4 {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -72,6 +75,15 @@
pinctrl-names = "default";
pinctrl-0 = <&divclk4_pin_a>;
};
+
+ div1_mclk: divclk1 {
+ compatible = "gpio-gate-clock";
+ pinctrl-0 = <&audio_mclk>;
+ pinctrl-names = "default";
+ clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+ #clock-cells = <0>;
+ enable-gpios = <&pm8994_gpios 15 0>;
+ };
};
soc {
@@ -453,6 +465,16 @@
};
};
+ slim_msm: slim@91c0000 {
+ ngd@1 {
+ wcd9335: codec@1{
+ clock-names = "mclk", "slimbus";
+ clocks = <&div1_mclk>,
+ <&rpmcc RPM_SMD_BB_CLK1>;
+ };
+ };
+ };
+
mdss@900000 {
status = "okay";
@@ -666,3 +688,75 @@
};
};
};
+
+&sound {
+ compatible = "qcom,apq8096-sndcard";
+ model = "DB820c";
+ audio-routing = "RX_BIAS", "MCLK";
+
+ mm1-dai-link {
+ link-name = "MultiMedia1";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+ };
+ };
+
+ mm2-dai-link {
+ link-name = "MultiMedia2";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
+ };
+ };
+
+ mm3-dai-link {
+ link-name = "MultiMedia3";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
+ };
+ };
+
+ hdmi-dai-link {
+ link-name = "HDMI";
+ cpu {
+ sound-dai = <&q6afedai HDMI_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&hdmi 0>;
+ };
+ };
+
+ slim-dai-link {
+ link-name = "SLIM Playback";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_6_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9335 6>;
+ };
+ };
+
+ slimcap-dai-link {
+ link-name = "SLIM Capture";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_0_TX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9335 1>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi
index 131878db9852..fba2229b6236 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi
@@ -13,6 +13,49 @@
&msmgpio {
+ wcd9xxx_intr {
+ wcd_intr_default: wcd_intr_default{
+ mux {
+ pins = "gpio54";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio54";
+ drive-strength = <2>; /* 2 mA */
+ bias-pull-down; /* pull down */
+ input-enable;
+ };
+ };
+ };
+
+ cdc_reset_ctrl {
+ cdc_reset_sleep: cdc_reset_sleep {
+ mux {
+ pins = "gpio64";
+ function = "gpio";
+ };
+ config {
+ pins = "gpio64";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+ };
+ cdc_reset_active:cdc_reset_active {
+ mux {
+ pins = "gpio64";
+ function = "gpio";
+ };
+ config {
+ pins = "gpio64";
+ drive-strength = <16>;
+ bias-pull-down;
+ output-high;
+ };
+ };
+ };
+
blsp1_spi0_default: blsp1_spi0_default {
pinmux {
function = "blsp_spi1";
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 095041589954..79fa666a4522 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -14,6 +14,7 @@
#include <dt-bindings/clock/qcom,gcc-msm8996.h>
#include <dt-bindings/clock/qcom,mmcc-msm8996.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/soc/qcom,apr.h>
/ {
interrupt-parent = <&intc>;
@@ -1183,6 +1184,33 @@
power-domains = <&mmcc MDSS_GDSC>;
};
+ lpass_q6_smmu: arm,smmu-lpass_q6@1600000 {
+ compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
+ reg = <0x1600000 0x20000>;
+ #iommu-cells = <1>;
+ power-domains = <&gcc HLOS1_VOTE_LPASS_CORE_GDSC>;
+
+ #global-interrupts = <1>;
+ interrupts = <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&gcc GCC_HLOS1_VOTE_LPASS_CORE_SMMU_CLK>,
+ <&gcc GCC_HLOS1_VOTE_LPASS_ADSP_SMMU_CLK>;
+ clock-names = "iface", "bus";
+ status = "okay";
+ };
+
agnoc@0 {
power-domains = <&gcc AGGRE0_NOC_GDSC>;
compatible = "simple-pm-bus";
@@ -1349,6 +1377,66 @@
};
};
+ slimbam:dma@9184000
+ {
+ compatible = "qcom,bam-v1.7.0";
+ qcom,controlled-remotely;
+ reg = <0x9184000 0x32000>;
+ num-channels = <31>;
+ interrupts = <0 164 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ qcom,ee = <1>;
+ qcom,num-ees = <2>;
+ };
+
+ slim_msm: slim@91c0000 {
+ compatible = "qcom,slim-ngd-v1.5.0";
+ reg = <0x91c0000 0x2C000>;
+ reg-names = "ctrl";
+ interrupts = <0 163 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&slimbam 3>, <&slimbam 4>,
+ <&slimbam 5>, <&slimbam 6>;
+ dma-names = "rx", "tx", "tx2", "rx2";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ngd@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ tasha_ifd: tas-ifd {
+ compatible = "slim217,1a0";
+ reg = <0 0>;
+ };
+
+ wcd9335: codec@1{
+ pinctrl-0 = <&cdc_reset_active &wcd_intr_default>;
+ pinctrl-names = "default";
+
+ compatible = "slim217,1a0";
+ reg = <1 0>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <54 IRQ_TYPE_LEVEL_HIGH>,
+ <53 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "intr1", "intr2";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reset-gpios = <&msmgpio 64 0>;
+
+ slim-ifc-dev = <&tasha_ifd>;
+
+ vdd-buck-supply = <&pm8994_s4>;
+ vdd-buck-sido-supply = <&pm8994_s4>;
+ vdd-tx-supply = <&pm8994_s4>;
+ vdd-rx-supply = <&pm8994_s4>;
+ vdd-io-supply = <&pm8994_s4>;
+
+ #sound-dai-cells = <1>;
+ };
+ };
+ };
+
gpu@b00000 {
compatible = "qcom,adreno-530.2", "qcom,adreno";
#stream-id-cells = <16>;
@@ -1507,6 +1595,7 @@
phys = <&hdmi_phy>;
phy-names = "hdmi_phy";
+ #sound-dai-cells = <1>;
ports {
#address-cells = <1>;
@@ -1545,6 +1634,9 @@
};
};
+ sound: sound {
+ };
+
adsp-pil {
compatible = "qcom,msm8996-adsp-pil";
@@ -1571,6 +1663,54 @@
mboxes = <&apcs_glb 8>;
qcom,smd-edge = <1>;
qcom,remote-pid = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ apr {
+ power-domains = <&gcc HLOS1_VOTE_LPASS_ADSP_GDSC>;
+ compatible = "qcom,apr-v2";
+ qcom,smd-channels = "apr_audio_svc";
+ reg = <APR_DOMAIN_ADSP>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ q6core {
+ reg = <APR_SVC_ADSP_CORE>;
+ compatible = "qcom,q6core";
+ };
+
+ q6afe: q6afe {
+ compatible = "qcom,q6afe";
+ reg = <APR_SVC_AFE>;
+ q6afedai: dais {
+ compatible = "qcom,q6afe-dais";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+ hdmi@1 {
+ reg = <1>;
+ };
+ };
+ };
+
+ q6asm: q6asm {
+ compatible = "qcom,q6asm";
+ reg = <APR_SVC_ASM>;
+ q6asmdai: dais {
+ compatible = "qcom,q6asm-dais";
+ #sound-dai-cells = <1>;
+ iommus = <&lpass_q6_smmu 1>;
+ };
+ };
+
+ q6adm: q6adm {
+ compatible = "qcom,q6adm";
+ reg = <APR_SVC_ADM>;
+ q6routing: routing {
+ compatible = "qcom,q6adm-routing";
+ #sound-dai-cells = <0>;
+ };
+ };
+ };
};
};
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v2 6/6] arm64: dts: db820c: Add sound card support
@ 2019-01-30 11:04 ` Srinivas Kandagatla
0 siblings, 0 replies; 14+ messages in thread
From: Srinivas Kandagatla @ 2019-01-30 11:04 UTC (permalink / raw)
To: andy.gross
Cc: linux-arm-msm, Srinivas Kandagatla, linux-arm-kernel, devicetree
This patch adds support both digital and analog audio on DB820c.
This board has HDMI port and 3.5mm audio jack to support both digital
and analog audio respectively.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
.../dts/qcom/apq8096-db820c-pmic-pins.dtsi | 8 +
arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 94 ++++++++++++
arch/arm64/boot/dts/qcom/msm8996-pins.dtsi | 43 ++++++
arch/arm64/boot/dts/qcom/msm8996.dtsi | 140 ++++++++++++++++++
4 files changed, 285 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi
index a6ad3d7fe655..31a3e3311ad5 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi
@@ -36,6 +36,14 @@
};
};
+ audio_mclk: clk_div1 {
+ pinconf {
+ pins = "gpio15";
+ function = "func1";
+ power-source = <PM8994_GPIO_S4>; // 1.8V
+ };
+ };
+
volume_up_gpio: pm8996_gpio2 {
pinconf {
pins = "gpio2";
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index 1e78f0b47c89..7f4a8a08a029 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -18,6 +18,8 @@
#include "apq8096-db820c-pmic-pins.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
/*
* GPIO name legend: proper name = the GPIO line is used as GPIO
@@ -63,6 +65,7 @@
};
clocks {
+ compatible = "simple-bus";
divclk4: divclk4 {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -72,6 +75,15 @@
pinctrl-names = "default";
pinctrl-0 = <&divclk4_pin_a>;
};
+
+ div1_mclk: divclk1 {
+ compatible = "gpio-gate-clock";
+ pinctrl-0 = <&audio_mclk>;
+ pinctrl-names = "default";
+ clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+ #clock-cells = <0>;
+ enable-gpios = <&pm8994_gpios 15 0>;
+ };
};
soc {
@@ -453,6 +465,16 @@
};
};
+ slim_msm: slim@91c0000 {
+ ngd@1 {
+ wcd9335: codec@1{
+ clock-names = "mclk", "slimbus";
+ clocks = <&div1_mclk>,
+ <&rpmcc RPM_SMD_BB_CLK1>;
+ };
+ };
+ };
+
mdss@900000 {
status = "okay";
@@ -666,3 +688,75 @@
};
};
};
+
+&sound {
+ compatible = "qcom,apq8096-sndcard";
+ model = "DB820c";
+ audio-routing = "RX_BIAS", "MCLK";
+
+ mm1-dai-link {
+ link-name = "MultiMedia1";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+ };
+ };
+
+ mm2-dai-link {
+ link-name = "MultiMedia2";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
+ };
+ };
+
+ mm3-dai-link {
+ link-name = "MultiMedia3";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
+ };
+ };
+
+ hdmi-dai-link {
+ link-name = "HDMI";
+ cpu {
+ sound-dai = <&q6afedai HDMI_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&hdmi 0>;
+ };
+ };
+
+ slim-dai-link {
+ link-name = "SLIM Playback";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_6_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9335 6>;
+ };
+ };
+
+ slimcap-dai-link {
+ link-name = "SLIM Capture";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_0_TX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9335 1>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi
index 131878db9852..fba2229b6236 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi
@@ -13,6 +13,49 @@
&msmgpio {
+ wcd9xxx_intr {
+ wcd_intr_default: wcd_intr_default{
+ mux {
+ pins = "gpio54";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio54";
+ drive-strength = <2>; /* 2 mA */
+ bias-pull-down; /* pull down */
+ input-enable;
+ };
+ };
+ };
+
+ cdc_reset_ctrl {
+ cdc_reset_sleep: cdc_reset_sleep {
+ mux {
+ pins = "gpio64";
+ function = "gpio";
+ };
+ config {
+ pins = "gpio64";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+ };
+ cdc_reset_active:cdc_reset_active {
+ mux {
+ pins = "gpio64";
+ function = "gpio";
+ };
+ config {
+ pins = "gpio64";
+ drive-strength = <16>;
+ bias-pull-down;
+ output-high;
+ };
+ };
+ };
+
blsp1_spi0_default: blsp1_spi0_default {
pinmux {
function = "blsp_spi1";
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 095041589954..79fa666a4522 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -14,6 +14,7 @@
#include <dt-bindings/clock/qcom,gcc-msm8996.h>
#include <dt-bindings/clock/qcom,mmcc-msm8996.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/soc/qcom,apr.h>
/ {
interrupt-parent = <&intc>;
@@ -1183,6 +1184,33 @@
power-domains = <&mmcc MDSS_GDSC>;
};
+ lpass_q6_smmu: arm,smmu-lpass_q6@1600000 {
+ compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
+ reg = <0x1600000 0x20000>;
+ #iommu-cells = <1>;
+ power-domains = <&gcc HLOS1_VOTE_LPASS_CORE_GDSC>;
+
+ #global-interrupts = <1>;
+ interrupts = <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&gcc GCC_HLOS1_VOTE_LPASS_CORE_SMMU_CLK>,
+ <&gcc GCC_HLOS1_VOTE_LPASS_ADSP_SMMU_CLK>;
+ clock-names = "iface", "bus";
+ status = "okay";
+ };
+
agnoc@0 {
power-domains = <&gcc AGGRE0_NOC_GDSC>;
compatible = "simple-pm-bus";
@@ -1349,6 +1377,66 @@
};
};
+ slimbam:dma@9184000
+ {
+ compatible = "qcom,bam-v1.7.0";
+ qcom,controlled-remotely;
+ reg = <0x9184000 0x32000>;
+ num-channels = <31>;
+ interrupts = <0 164 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ qcom,ee = <1>;
+ qcom,num-ees = <2>;
+ };
+
+ slim_msm: slim@91c0000 {
+ compatible = "qcom,slim-ngd-v1.5.0";
+ reg = <0x91c0000 0x2C000>;
+ reg-names = "ctrl";
+ interrupts = <0 163 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&slimbam 3>, <&slimbam 4>,
+ <&slimbam 5>, <&slimbam 6>;
+ dma-names = "rx", "tx", "tx2", "rx2";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ngd@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ tasha_ifd: tas-ifd {
+ compatible = "slim217,1a0";
+ reg = <0 0>;
+ };
+
+ wcd9335: codec@1{
+ pinctrl-0 = <&cdc_reset_active &wcd_intr_default>;
+ pinctrl-names = "default";
+
+ compatible = "slim217,1a0";
+ reg = <1 0>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <54 IRQ_TYPE_LEVEL_HIGH>,
+ <53 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "intr1", "intr2";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reset-gpios = <&msmgpio 64 0>;
+
+ slim-ifc-dev = <&tasha_ifd>;
+
+ vdd-buck-supply = <&pm8994_s4>;
+ vdd-buck-sido-supply = <&pm8994_s4>;
+ vdd-tx-supply = <&pm8994_s4>;
+ vdd-rx-supply = <&pm8994_s4>;
+ vdd-io-supply = <&pm8994_s4>;
+
+ #sound-dai-cells = <1>;
+ };
+ };
+ };
+
gpu@b00000 {
compatible = "qcom,adreno-530.2", "qcom,adreno";
#stream-id-cells = <16>;
@@ -1507,6 +1595,7 @@
phys = <&hdmi_phy>;
phy-names = "hdmi_phy";
+ #sound-dai-cells = <1>;
ports {
#address-cells = <1>;
@@ -1545,6 +1634,9 @@
};
};
+ sound: sound {
+ };
+
adsp-pil {
compatible = "qcom,msm8996-adsp-pil";
@@ -1571,6 +1663,54 @@
mboxes = <&apcs_glb 8>;
qcom,smd-edge = <1>;
qcom,remote-pid = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ apr {
+ power-domains = <&gcc HLOS1_VOTE_LPASS_ADSP_GDSC>;
+ compatible = "qcom,apr-v2";
+ qcom,smd-channels = "apr_audio_svc";
+ reg = <APR_DOMAIN_ADSP>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ q6core {
+ reg = <APR_SVC_ADSP_CORE>;
+ compatible = "qcom,q6core";
+ };
+
+ q6afe: q6afe {
+ compatible = "qcom,q6afe";
+ reg = <APR_SVC_AFE>;
+ q6afedai: dais {
+ compatible = "qcom,q6afe-dais";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+ hdmi@1 {
+ reg = <1>;
+ };
+ };
+ };
+
+ q6asm: q6asm {
+ compatible = "qcom,q6asm";
+ reg = <APR_SVC_ASM>;
+ q6asmdai: dais {
+ compatible = "qcom,q6asm-dais";
+ #sound-dai-cells = <1>;
+ iommus = <&lpass_q6_smmu 1>;
+ };
+ };
+
+ q6adm: q6adm {
+ compatible = "qcom,q6adm";
+ reg = <APR_SVC_ADM>;
+ q6routing: routing {
+ compatible = "qcom,q6adm-routing";
+ #sound-dai-cells = <0>;
+ };
+ };
+ };
};
};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread