Re: [PATCH 1/2] ARM: dts: rskrza1: Add I2C support

[Simon Horman <horms@verge.net.au>]

On Wed, Mar 20, 2019 at 08:44:09PM +0100, Geert Uytterhoeven wrote:
> Enable the I2C bus, and add the following devices:
>   - Two CAT9554 port expanders (8 GPIOs, interrupt not wired by
>     default),
>   - R1EX24016ASAS0A EEPROM.
> 
> The bus also contains a MAX9856 Audio Codec, which is not yet supported.
> 
> All devices (incl. the audio codec) are documented to support an I2C bus
> running at 400 kHz.
> 
> Pinctrl is based on the RZ/A BSP.
> 
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> ---
> Pending acceptance of the DT binding patches documenting the
> "onnn,cat9554" and "renesas,r1ex24016" compatible values.

Thanks.

I'm marking this series as deferred pending acceptance of the bindings.
Please repost or ping me once that has happened.

> ---
>  arch/arm/boot/dts/r7s72100-rskrza1.dts | 33 ++++++++++++++++++++++++++
>  1 file changed, 33 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/r7s72100-rskrza1.dts b/arch/arm/boot/dts/r7s72100-rskrza1.dts
> index 8ee44a100e9a44c4..60e80ecbbf6826bc 100644
> --- a/arch/arm/boot/dts/r7s72100-rskrza1.dts
> +++ b/arch/arm/boot/dts/r7s72100-rskrza1.dts
> @@ -47,6 +47,34 @@
>  	clock-frequency = <13330000>;
>  };
>  
> +&i2c3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c3_pins>;
> +	status = "okay";
> +
> +	clock-frequency = <400000>;
> +
> +	io_expander1: gpio@20 {
> +		compatible = "onnn,cat9554";
> +		reg = <0x20>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +	};
> +
> +	io_expander2: gpio@21 {
> +		compatible = "onnn,cat9554";
> +		reg = <0x21>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +	};
> +
> +	eeprom@50 {
> +		compatible = "renesas,r1ex24016", "atmel,24c16";
> +		reg = <0x50>;
> +		pagesize = <16>;
> +	};
> +};
> +
>  &usb_x1_clk {
>  	clock-frequency = <48000000>;
>  };
> @@ -56,6 +84,11 @@
>  };
>  
>  &pinctrl {
> +	/* RIIC ch3 (Port Expander, EEPROM (MAC Addr), Audio Codec) */
> +	i2c3_pins: i2c3 {
> +		pinmux = <RZA1_PINMUX(1, 6, 1)>,	/* RIIC3SCL */
> +			 <RZA1_PINMUX(1, 7, 1)>;	/* RIIC3SDA */
> +	};
>  
>  	/* Serial Console */
>  	scif2_pins: serial2 {
> -- 
> 2.17.1
>