* [PATCH 0/6] arm64: Add initial support for Odroid-N2
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: baylibre-upstreaming, Neil Armstrong, linux-amlogic,
linux-arm-kernel, linux-kernel
This patchset adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC
The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12A has additional clocks like for CSI an other components
Dependencies :
- Patch 1, 3, 4, 5 : None
- Patch 2 : Depends on the v5.2 meson-clk PULL request
- Patch 6 depends on the G12A Display DT patchset at [2]
Changes since RFC at [1]:
- Added bindings review tags
- Moved the fclk_div3 CRITICAL flags to the gate
- Removed invalid CRITICAL flags on the cpu clocks
[1] https://lkml.kernel.org/r/20190327103308.25058-1-narmstrong@baylibre.com
[2] https://lkml.kernel.org/r/20190325145914.32391-1-narmstrong@baylibre.com
Neil Armstrong (6):
dt-bindings: clk: meson: add g12b periph clock controller bindings
clk: meson: g12a: Add support for G12B CPUB clocks
clk: meson: g12a: mark fclk_div3 as critical
dt-bindings: arm: amlogic: add G12B bindings
dt-bindings: arm: amlogic: add Odroid-N2 binding
arm64: dts: meson: Add minimal support for Odroid-N2
.../devicetree/bindings/arm/amlogic.txt | 6 +
.../bindings/clock/amlogic,gxbb-clkc.txt | 1 +
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 178 +++++++
arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 ++++
drivers/clk/meson/g12a.c | 451 ++++++++++++++++++
drivers/clk/meson/g12a.h | 20 +-
7 files changed, 738 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
--
2.21.0
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH 0/6] arm64: Add initial support for Odroid-N2
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: baylibre-upstreaming, linux-amlogic, linux-kernel,
linux-arm-kernel, Neil Armstrong
This patchset adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC
The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12A has additional clocks like for CSI an other components
Dependencies :
- Patch 1, 3, 4, 5 : None
- Patch 2 : Depends on the v5.2 meson-clk PULL request
- Patch 6 depends on the G12A Display DT patchset at [2]
Changes since RFC at [1]:
- Added bindings review tags
- Moved the fclk_div3 CRITICAL flags to the gate
- Removed invalid CRITICAL flags on the cpu clocks
[1] https://lkml.kernel.org/r/20190327103308.25058-1-narmstrong@baylibre.com
[2] https://lkml.kernel.org/r/20190325145914.32391-1-narmstrong@baylibre.com
Neil Armstrong (6):
dt-bindings: clk: meson: add g12b periph clock controller bindings
clk: meson: g12a: Add support for G12B CPUB clocks
clk: meson: g12a: mark fclk_div3 as critical
dt-bindings: arm: amlogic: add G12B bindings
dt-bindings: arm: amlogic: add Odroid-N2 binding
arm64: dts: meson: Add minimal support for Odroid-N2
.../devicetree/bindings/arm/amlogic.txt | 6 +
.../bindings/clock/amlogic,gxbb-clkc.txt | 1 +
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 178 +++++++
arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 ++++
drivers/clk/meson/g12a.c | 451 ++++++++++++++++++
drivers/clk/meson/g12a.h | 20 +-
7 files changed, 738 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
--
2.21.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH 0/6] arm64: Add initial support for Odroid-N2
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: baylibre-upstreaming, linux-amlogic, linux-kernel,
linux-arm-kernel, Neil Armstrong
This patchset adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC
The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12A has additional clocks like for CSI an other components
Dependencies :
- Patch 1, 3, 4, 5 : None
- Patch 2 : Depends on the v5.2 meson-clk PULL request
- Patch 6 depends on the G12A Display DT patchset at [2]
Changes since RFC at [1]:
- Added bindings review tags
- Moved the fclk_div3 CRITICAL flags to the gate
- Removed invalid CRITICAL flags on the cpu clocks
[1] https://lkml.kernel.org/r/20190327103308.25058-1-narmstrong@baylibre.com
[2] https://lkml.kernel.org/r/20190325145914.32391-1-narmstrong@baylibre.com
Neil Armstrong (6):
dt-bindings: clk: meson: add g12b periph clock controller bindings
clk: meson: g12a: Add support for G12B CPUB clocks
clk: meson: g12a: mark fclk_div3 as critical
dt-bindings: arm: amlogic: add G12B bindings
dt-bindings: arm: amlogic: add Odroid-N2 binding
arm64: dts: meson: Add minimal support for Odroid-N2
.../devicetree/bindings/arm/amlogic.txt | 6 +
.../bindings/clock/amlogic,gxbb-clkc.txt | 1 +
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 178 +++++++
arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 ++++
drivers/clk/meson/g12a.c | 451 ++++++++++++++++++
drivers/clk/meson/g12a.h | 20 +-
7 files changed, 738 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
--
2.21.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH 1/6] dt-bindings: clk: meson: add g12b periph clock controller bindings
2019-04-04 15:05 ` Neil Armstrong
(?)
@ 2019-04-04 15:05 ` Neil Armstrong
-1 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, devicetree, jbrunet
Cc: baylibre-upstreaming, Neil Armstrong, linux-amlogic,
linux-arm-kernel, linux-kernel, Rob Herring
This patch adds the specific Amlogic G12B clock driver compatible.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12A has additional clocks like for CSI an other components
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt
index 5c8b105be4d6..6eaa52092313 100644
--- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt
+++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt
@@ -10,6 +10,7 @@ Required Properties:
"amlogic,gxl-clkc" for GXL and GXM SoC,
"amlogic,axg-clkc" for AXG SoC.
"amlogic,g12a-clkc" for G12A SoC.
+ "amlogic,g12b-clkc" for G12B SoC.
- clocks : list of clock phandle, one for each entry clock-names.
- clock-names : should contain the following:
* "xtal": the platform xtal
--
2.21.0
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 1/6] dt-bindings: clk: meson: add g12b periph clock controller bindings
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, devicetree, jbrunet
Cc: Rob Herring, Neil Armstrong, baylibre-upstreaming, linux-kernel,
linux-amlogic, linux-arm-kernel
This patch adds the specific Amlogic G12B clock driver compatible.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12A has additional clocks like for CSI an other components
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt
index 5c8b105be4d6..6eaa52092313 100644
--- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt
+++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt
@@ -10,6 +10,7 @@ Required Properties:
"amlogic,gxl-clkc" for GXL and GXM SoC,
"amlogic,axg-clkc" for AXG SoC.
"amlogic,g12a-clkc" for G12A SoC.
+ "amlogic,g12b-clkc" for G12B SoC.
- clocks : list of clock phandle, one for each entry clock-names.
- clock-names : should contain the following:
* "xtal": the platform xtal
--
2.21.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 1/6] dt-bindings: clk: meson: add g12b periph clock controller bindings
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, devicetree, jbrunet
Cc: Rob Herring, Neil Armstrong, baylibre-upstreaming, linux-kernel,
linux-amlogic, linux-arm-kernel
This patch adds the specific Amlogic G12B clock driver compatible.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12A has additional clocks like for CSI an other components
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt
index 5c8b105be4d6..6eaa52092313 100644
--- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt
+++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt
@@ -10,6 +10,7 @@ Required Properties:
"amlogic,gxl-clkc" for GXL and GXM SoC,
"amlogic,axg-clkc" for AXG SoC.
"amlogic,g12a-clkc" for G12A SoC.
+ "amlogic,g12b-clkc" for G12B SoC.
- clocks : list of clock phandle, one for each entry clock-names.
- clock-names : should contain the following:
* "xtal": the platform xtal
--
2.21.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 2/6] clk: meson: g12a: Add support for G12B CPUB clocks
2019-04-04 15:05 ` Neil Armstrong
(?)
@ 2019-04-04 15:05 ` Neil Armstrong
-1 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: baylibre-upstreaming, Neil Armstrong, linux-amlogic,
linux-arm-kernel, linux-kernel, linux-clk
This patch support for the specific Amlogic G12B clocks.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12A has additional clocks like for CSI an other components
Here only the cpu clock tree is handled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
drivers/clk/meson/g12a.c | 441 +++++++++++++++++++++++++++++++++++++++
drivers/clk/meson/g12a.h | 20 +-
2 files changed, 460 insertions(+), 1 deletion(-)
diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
index fb698778a614..14aaa02bb621 100644
--- a/drivers/clk/meson/g12a.c
+++ b/drivers/clk/meson/g12a.c
@@ -150,6 +150,57 @@ static struct clk_regmap g12a_sys_pll = {
},
};
+static struct clk_regmap g12b_sys1_pll_dco = {
+ .data = &(struct meson_clk_pll_data){
+ .en = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .m = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 0,
+ .width = 8,
+ },
+ .n = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 10,
+ .width = 5,
+ },
+ .l = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 31,
+ .width = 1,
+ },
+ .rst = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 29,
+ .width = 1,
+ },
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys1_pll_dco",
+ .ops = &meson_clk_pll_ro_ops,
+ .parent_names = (const char *[]){ IN_PREFIX "xtal" },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap g12b_sys1_pll = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = HHI_SYS1_PLL_CNTL0,
+ .shift = 16,
+ .width = 3,
+ .flags = CLK_DIVIDER_POWER_OF_TWO,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys1_pll",
+ .ops = &clk_regmap_divider_ro_ops,
+ .parent_names = (const char *[]){ "sys1_pll_dco" },
+ .num_parents = 1,
+ },
+};
+
static struct clk_regmap g12a_sys_pll_div16_en = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_SYS_CPU_CLK_CNTL1,
@@ -306,6 +357,150 @@ static struct clk_regmap g12a_cpu_clk = {
},
};
+/* Datasheet names this field as "Final_mux_sel" */
+static struct clk_regmap g12b_cpu_clk = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPU_CLK_CNTL0,
+ .mask = 0x1,
+ .shift = 11,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpu_clk",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpu_clk_dyn",
+ "sys1_pll" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "premux0" */
+static struct clk_regmap g12b_cpub_clk_dyn0_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x3,
+ .shift = 0,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn0_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ IN_PREFIX "xtal",
+ "fclk_div2",
+ "fclk_div3" },
+ .num_parents = 3,
+ },
+};
+
+/* Datasheet names this field as "mux0_divn_tcnt" */
+static struct clk_regmap g12b_cpub_clk_dyn0_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .shift = 4,
+ .width = 6,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn0_div",
+ .ops = &clk_regmap_divider_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn0_sel" },
+ .num_parents = 1,
+ },
+};
+
+/* Datasheet names this field as "postmux0" */
+static struct clk_regmap g12b_cpub_clk_dyn0 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 2,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn0",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn0_sel",
+ "cpub_clk_dyn0_div" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "premux1" */
+static struct clk_regmap g12b_cpub_clk_dyn1_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x3,
+ .shift = 16,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn1_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ IN_PREFIX "xtal",
+ "fclk_div2",
+ "fclk_div3" },
+ .num_parents = 3,
+ },
+};
+
+/* Datasheet names this field as "Mux1_divn_tcnt" */
+static struct clk_regmap g12b_cpub_clk_dyn1_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .shift = 20,
+ .width = 6,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn1_div",
+ .ops = &clk_regmap_divider_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn1_sel" },
+ .num_parents = 1,
+ },
+};
+
+/* Datasheet names this field as "postmux1" */
+static struct clk_regmap g12b_cpub_clk_dyn1 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 18,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn1",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn1_sel",
+ "cpub_clk_dyn1_div" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "Final_dyn_mux_sel" */
+static struct clk_regmap g12b_cpub_clk_dyn = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn0",
+ "cpub_clk_dyn1" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "Final_mux_sel" */
+static struct clk_regmap g12b_cpub_clk = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 11,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn",
+ "sys_pll" },
+ .num_parents = 2,
+ },
+};
+
static struct clk_regmap g12a_cpu_clk_div16_en = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_SYS_CPU_CLK_CNTL1,
@@ -2798,6 +2993,234 @@ static struct clk_hw_onecell_data g12a_hw_onecell_data = {
.num = NR_CLKS,
};
+static struct clk_hw_onecell_data g12b_hw_onecell_data = {
+ .hws = {
+ [CLKID_SYS_PLL] = &g12a_sys_pll.hw,
+ [CLKID_FIXED_PLL] = &g12a_fixed_pll.hw,
+ [CLKID_FCLK_DIV2] = &g12a_fclk_div2.hw,
+ [CLKID_FCLK_DIV3] = &g12a_fclk_div3.hw,
+ [CLKID_FCLK_DIV4] = &g12a_fclk_div4.hw,
+ [CLKID_FCLK_DIV5] = &g12a_fclk_div5.hw,
+ [CLKID_FCLK_DIV7] = &g12a_fclk_div7.hw,
+ [CLKID_FCLK_DIV2P5] = &g12a_fclk_div2p5.hw,
+ [CLKID_GP0_PLL] = &g12a_gp0_pll.hw,
+ [CLKID_MPEG_SEL] = &g12a_mpeg_clk_sel.hw,
+ [CLKID_MPEG_DIV] = &g12a_mpeg_clk_div.hw,
+ [CLKID_CLK81] = &g12a_clk81.hw,
+ [CLKID_MPLL0] = &g12a_mpll0.hw,
+ [CLKID_MPLL1] = &g12a_mpll1.hw,
+ [CLKID_MPLL2] = &g12a_mpll2.hw,
+ [CLKID_MPLL3] = &g12a_mpll3.hw,
+ [CLKID_DDR] = &g12a_ddr.hw,
+ [CLKID_DOS] = &g12a_dos.hw,
+ [CLKID_AUDIO_LOCKER] = &g12a_audio_locker.hw,
+ [CLKID_MIPI_DSI_HOST] = &g12a_mipi_dsi_host.hw,
+ [CLKID_ETH_PHY] = &g12a_eth_phy.hw,
+ [CLKID_ISA] = &g12a_isa.hw,
+ [CLKID_PL301] = &g12a_pl301.hw,
+ [CLKID_PERIPHS] = &g12a_periphs.hw,
+ [CLKID_SPICC0] = &g12a_spicc_0.hw,
+ [CLKID_I2C] = &g12a_i2c.hw,
+ [CLKID_SANA] = &g12a_sana.hw,
+ [CLKID_SD] = &g12a_sd.hw,
+ [CLKID_RNG0] = &g12a_rng0.hw,
+ [CLKID_UART0] = &g12a_uart0.hw,
+ [CLKID_SPICC1] = &g12a_spicc_1.hw,
+ [CLKID_HIU_IFACE] = &g12a_hiu_reg.hw,
+ [CLKID_MIPI_DSI_PHY] = &g12a_mipi_dsi_phy.hw,
+ [CLKID_ASSIST_MISC] = &g12a_assist_misc.hw,
+ [CLKID_SD_EMMC_A] = &g12a_emmc_a.hw,
+ [CLKID_SD_EMMC_B] = &g12a_emmc_b.hw,
+ [CLKID_SD_EMMC_C] = &g12a_emmc_c.hw,
+ [CLKID_AUDIO_CODEC] = &g12a_audio_codec.hw,
+ [CLKID_AUDIO] = &g12a_audio.hw,
+ [CLKID_ETH] = &g12a_eth_core.hw,
+ [CLKID_DEMUX] = &g12a_demux.hw,
+ [CLKID_AUDIO_IFIFO] = &g12a_audio_ififo.hw,
+ [CLKID_ADC] = &g12a_adc.hw,
+ [CLKID_UART1] = &g12a_uart1.hw,
+ [CLKID_G2D] = &g12a_g2d.hw,
+ [CLKID_RESET] = &g12a_reset.hw,
+ [CLKID_PCIE_COMB] = &g12a_pcie_comb.hw,
+ [CLKID_PARSER] = &g12a_parser.hw,
+ [CLKID_USB] = &g12a_usb_general.hw,
+ [CLKID_PCIE_PHY] = &g12a_pcie_phy.hw,
+ [CLKID_AHB_ARB0] = &g12a_ahb_arb0.hw,
+ [CLKID_AHB_DATA_BUS] = &g12a_ahb_data_bus.hw,
+ [CLKID_AHB_CTRL_BUS] = &g12a_ahb_ctrl_bus.hw,
+ [CLKID_HTX_HDCP22] = &g12a_htx_hdcp22.hw,
+ [CLKID_HTX_PCLK] = &g12a_htx_pclk.hw,
+ [CLKID_BT656] = &g12a_bt656.hw,
+ [CLKID_USB1_DDR_BRIDGE] = &g12a_usb1_to_ddr.hw,
+ [CLKID_MMC_PCLK] = &g12a_mmc_pclk.hw,
+ [CLKID_UART2] = &g12a_uart2.hw,
+ [CLKID_VPU_INTR] = &g12a_vpu_intr.hw,
+ [CLKID_GIC] = &g12a_gic.hw,
+ [CLKID_SD_EMMC_A_CLK0_SEL] = &g12a_sd_emmc_a_clk0_sel.hw,
+ [CLKID_SD_EMMC_A_CLK0_DIV] = &g12a_sd_emmc_a_clk0_div.hw,
+ [CLKID_SD_EMMC_A_CLK0] = &g12a_sd_emmc_a_clk0.hw,
+ [CLKID_SD_EMMC_B_CLK0_SEL] = &g12a_sd_emmc_b_clk0_sel.hw,
+ [CLKID_SD_EMMC_B_CLK0_DIV] = &g12a_sd_emmc_b_clk0_div.hw,
+ [CLKID_SD_EMMC_B_CLK0] = &g12a_sd_emmc_b_clk0.hw,
+ [CLKID_SD_EMMC_C_CLK0_SEL] = &g12a_sd_emmc_c_clk0_sel.hw,
+ [CLKID_SD_EMMC_C_CLK0_DIV] = &g12a_sd_emmc_c_clk0_div.hw,
+ [CLKID_SD_EMMC_C_CLK0] = &g12a_sd_emmc_c_clk0.hw,
+ [CLKID_MPLL0_DIV] = &g12a_mpll0_div.hw,
+ [CLKID_MPLL1_DIV] = &g12a_mpll1_div.hw,
+ [CLKID_MPLL2_DIV] = &g12a_mpll2_div.hw,
+ [CLKID_MPLL3_DIV] = &g12a_mpll3_div.hw,
+ [CLKID_FCLK_DIV2_DIV] = &g12a_fclk_div2_div.hw,
+ [CLKID_FCLK_DIV3_DIV] = &g12a_fclk_div3_div.hw,
+ [CLKID_FCLK_DIV4_DIV] = &g12a_fclk_div4_div.hw,
+ [CLKID_FCLK_DIV5_DIV] = &g12a_fclk_div5_div.hw,
+ [CLKID_FCLK_DIV7_DIV] = &g12a_fclk_div7_div.hw,
+ [CLKID_FCLK_DIV2P5_DIV] = &g12a_fclk_div2p5_div.hw,
+ [CLKID_HIFI_PLL] = &g12a_hifi_pll.hw,
+ [CLKID_VCLK2_VENCI0] = &g12a_vclk2_venci0.hw,
+ [CLKID_VCLK2_VENCI1] = &g12a_vclk2_venci1.hw,
+ [CLKID_VCLK2_VENCP0] = &g12a_vclk2_vencp0.hw,
+ [CLKID_VCLK2_VENCP1] = &g12a_vclk2_vencp1.hw,
+ [CLKID_VCLK2_VENCT0] = &g12a_vclk2_venct0.hw,
+ [CLKID_VCLK2_VENCT1] = &g12a_vclk2_venct1.hw,
+ [CLKID_VCLK2_OTHER] = &g12a_vclk2_other.hw,
+ [CLKID_VCLK2_ENCI] = &g12a_vclk2_enci.hw,
+ [CLKID_VCLK2_ENCP] = &g12a_vclk2_encp.hw,
+ [CLKID_DAC_CLK] = &g12a_dac_clk.hw,
+ [CLKID_AOCLK] = &g12a_aoclk_gate.hw,
+ [CLKID_IEC958] = &g12a_iec958_gate.hw,
+ [CLKID_ENC480P] = &g12a_enc480p.hw,
+ [CLKID_RNG1] = &g12a_rng1.hw,
+ [CLKID_VCLK2_ENCT] = &g12a_vclk2_enct.hw,
+ [CLKID_VCLK2_ENCL] = &g12a_vclk2_encl.hw,
+ [CLKID_VCLK2_VENCLMMC] = &g12a_vclk2_venclmmc.hw,
+ [CLKID_VCLK2_VENCL] = &g12a_vclk2_vencl.hw,
+ [CLKID_VCLK2_OTHER1] = &g12a_vclk2_other1.hw,
+ [CLKID_FIXED_PLL_DCO] = &g12a_fixed_pll_dco.hw,
+ [CLKID_SYS_PLL_DCO] = &g12a_sys_pll_dco.hw,
+ [CLKID_GP0_PLL_DCO] = &g12a_gp0_pll_dco.hw,
+ [CLKID_HIFI_PLL_DCO] = &g12a_hifi_pll_dco.hw,
+ [CLKID_DMA] = &g12a_dma.hw,
+ [CLKID_EFUSE] = &g12a_efuse.hw,
+ [CLKID_ROM_BOOT] = &g12a_rom_boot.hw,
+ [CLKID_RESET_SEC] = &g12a_reset_sec.hw,
+ [CLKID_SEC_AHB_APB3] = &g12a_sec_ahb_apb3.hw,
+ [CLKID_MPLL_PREDIV] = &g12a_mpll_prediv.hw,
+ [CLKID_VPU_0_SEL] = &g12a_vpu_0_sel.hw,
+ [CLKID_VPU_0_DIV] = &g12a_vpu_0_div.hw,
+ [CLKID_VPU_0] = &g12a_vpu_0.hw,
+ [CLKID_VPU_1_SEL] = &g12a_vpu_1_sel.hw,
+ [CLKID_VPU_1_DIV] = &g12a_vpu_1_div.hw,
+ [CLKID_VPU_1] = &g12a_vpu_1.hw,
+ [CLKID_VPU] = &g12a_vpu.hw,
+ [CLKID_VAPB_0_SEL] = &g12a_vapb_0_sel.hw,
+ [CLKID_VAPB_0_DIV] = &g12a_vapb_0_div.hw,
+ [CLKID_VAPB_0] = &g12a_vapb_0.hw,
+ [CLKID_VAPB_1_SEL] = &g12a_vapb_1_sel.hw,
+ [CLKID_VAPB_1_DIV] = &g12a_vapb_1_div.hw,
+ [CLKID_VAPB_1] = &g12a_vapb_1.hw,
+ [CLKID_VAPB_SEL] = &g12a_vapb_sel.hw,
+ [CLKID_VAPB] = &g12a_vapb.hw,
+ [CLKID_HDMI_PLL_DCO] = &g12a_hdmi_pll_dco.hw,
+ [CLKID_HDMI_PLL_OD] = &g12a_hdmi_pll_od.hw,
+ [CLKID_HDMI_PLL_OD2] = &g12a_hdmi_pll_od2.hw,
+ [CLKID_HDMI_PLL] = &g12a_hdmi_pll.hw,
+ [CLKID_VID_PLL] = &g12a_vid_pll_div.hw,
+ [CLKID_VID_PLL_SEL] = &g12a_vid_pll_sel.hw,
+ [CLKID_VID_PLL_DIV] = &g12a_vid_pll.hw,
+ [CLKID_VCLK_SEL] = &g12a_vclk_sel.hw,
+ [CLKID_VCLK2_SEL] = &g12a_vclk2_sel.hw,
+ [CLKID_VCLK_INPUT] = &g12a_vclk_input.hw,
+ [CLKID_VCLK2_INPUT] = &g12a_vclk2_input.hw,
+ [CLKID_VCLK_DIV] = &g12a_vclk_div.hw,
+ [CLKID_VCLK2_DIV] = &g12a_vclk2_div.hw,
+ [CLKID_VCLK] = &g12a_vclk.hw,
+ [CLKID_VCLK2] = &g12a_vclk2.hw,
+ [CLKID_VCLK_DIV1] = &g12a_vclk_div1.hw,
+ [CLKID_VCLK_DIV2_EN] = &g12a_vclk_div2_en.hw,
+ [CLKID_VCLK_DIV4_EN] = &g12a_vclk_div4_en.hw,
+ [CLKID_VCLK_DIV6_EN] = &g12a_vclk_div6_en.hw,
+ [CLKID_VCLK_DIV12_EN] = &g12a_vclk_div12_en.hw,
+ [CLKID_VCLK2_DIV1] = &g12a_vclk2_div1.hw,
+ [CLKID_VCLK2_DIV2_EN] = &g12a_vclk2_div2_en.hw,
+ [CLKID_VCLK2_DIV4_EN] = &g12a_vclk2_div4_en.hw,
+ [CLKID_VCLK2_DIV6_EN] = &g12a_vclk2_div6_en.hw,
+ [CLKID_VCLK2_DIV12_EN] = &g12a_vclk2_div12_en.hw,
+ [CLKID_VCLK_DIV2] = &g12a_vclk_div2.hw,
+ [CLKID_VCLK_DIV4] = &g12a_vclk_div4.hw,
+ [CLKID_VCLK_DIV6] = &g12a_vclk_div6.hw,
+ [CLKID_VCLK_DIV12] = &g12a_vclk_div12.hw,
+ [CLKID_VCLK2_DIV2] = &g12a_vclk2_div2.hw,
+ [CLKID_VCLK2_DIV4] = &g12a_vclk2_div4.hw,
+ [CLKID_VCLK2_DIV6] = &g12a_vclk2_div6.hw,
+ [CLKID_VCLK2_DIV12] = &g12a_vclk2_div12.hw,
+ [CLKID_CTS_ENCI_SEL] = &g12a_cts_enci_sel.hw,
+ [CLKID_CTS_ENCP_SEL] = &g12a_cts_encp_sel.hw,
+ [CLKID_CTS_VDAC_SEL] = &g12a_cts_vdac_sel.hw,
+ [CLKID_HDMI_TX_SEL] = &g12a_hdmi_tx_sel.hw,
+ [CLKID_CTS_ENCI] = &g12a_cts_enci.hw,
+ [CLKID_CTS_ENCP] = &g12a_cts_encp.hw,
+ [CLKID_CTS_VDAC] = &g12a_cts_vdac.hw,
+ [CLKID_HDMI_TX] = &g12a_hdmi_tx.hw,
+ [CLKID_HDMI_SEL] = &g12a_hdmi_sel.hw,
+ [CLKID_HDMI_DIV] = &g12a_hdmi_div.hw,
+ [CLKID_HDMI] = &g12a_hdmi.hw,
+ [CLKID_MALI_0_SEL] = &g12a_mali_0_sel.hw,
+ [CLKID_MALI_0_DIV] = &g12a_mali_0_div.hw,
+ [CLKID_MALI_0] = &g12a_mali_0.hw,
+ [CLKID_MALI_1_SEL] = &g12a_mali_1_sel.hw,
+ [CLKID_MALI_1_DIV] = &g12a_mali_1_div.hw,
+ [CLKID_MALI_1] = &g12a_mali_1.hw,
+ [CLKID_MALI] = &g12a_mali.hw,
+ [CLKID_MPLL_5OM_DIV] = &g12a_mpll_50m_div.hw,
+ [CLKID_MPLL_5OM] = &g12a_mpll_50m.hw,
+ [CLKID_SYS_PLL_DIV16_EN] = &g12a_sys_pll_div16_en.hw,
+ [CLKID_SYS_PLL_DIV16] = &g12a_sys_pll_div16.hw,
+ [CLKID_CPU_CLK_DYN0_SEL] = &g12a_cpu_clk_dyn0_sel.hw,
+ [CLKID_CPU_CLK_DYN0_DIV] = &g12a_cpu_clk_dyn0_div.hw,
+ [CLKID_CPU_CLK_DYN0] = &g12a_cpu_clk_dyn0.hw,
+ [CLKID_CPU_CLK_DYN1_SEL] = &g12a_cpu_clk_dyn1_sel.hw,
+ [CLKID_CPU_CLK_DYN1_DIV] = &g12a_cpu_clk_dyn1_div.hw,
+ [CLKID_CPU_CLK_DYN1] = &g12a_cpu_clk_dyn1.hw,
+ [CLKID_CPU_CLK_DYN] = &g12a_cpu_clk_dyn.hw,
+ [CLKID_CPU_CLK] = &g12b_cpu_clk.hw,
+ [CLKID_CPU_CLK_DIV16_EN] = &g12a_cpu_clk_div16_en.hw,
+ [CLKID_CPU_CLK_DIV16] = &g12a_cpu_clk_div16.hw,
+ [CLKID_CPU_CLK_APB_DIV] = &g12a_cpu_clk_apb_div.hw,
+ [CLKID_CPU_CLK_APB] = &g12a_cpu_clk_apb.hw,
+ [CLKID_CPU_CLK_ATB_DIV] = &g12a_cpu_clk_atb_div.hw,
+ [CLKID_CPU_CLK_ATB] = &g12a_cpu_clk_atb.hw,
+ [CLKID_CPU_CLK_AXI_DIV] = &g12a_cpu_clk_axi_div.hw,
+ [CLKID_CPU_CLK_AXI] = &g12a_cpu_clk_axi.hw,
+ [CLKID_CPU_CLK_TRACE_DIV] = &g12a_cpu_clk_trace_div.hw,
+ [CLKID_CPU_CLK_TRACE] = &g12a_cpu_clk_trace.hw,
+ [CLKID_PCIE_PLL_DCO] = &g12a_pcie_pll_dco.hw,
+ [CLKID_PCIE_PLL_DCO_DIV2] = &g12a_pcie_pll_dco_div2.hw,
+ [CLKID_PCIE_PLL_OD] = &g12a_pcie_pll_od.hw,
+ [CLKID_PCIE_PLL] = &g12a_pcie_pll.hw,
+ [CLKID_VDEC_1_SEL] = &g12a_vdec_1_sel.hw,
+ [CLKID_VDEC_1_DIV] = &g12a_vdec_1_div.hw,
+ [CLKID_VDEC_1] = &g12a_vdec_1.hw,
+ [CLKID_VDEC_HEVC_SEL] = &g12a_vdec_hevc_sel.hw,
+ [CLKID_VDEC_HEVC_DIV] = &g12a_vdec_hevc_div.hw,
+ [CLKID_VDEC_HEVC] = &g12a_vdec_hevc.hw,
+ [CLKID_VDEC_HEVCF_SEL] = &g12a_vdec_hevcf_sel.hw,
+ [CLKID_VDEC_HEVCF_DIV] = &g12a_vdec_hevcf_div.hw,
+ [CLKID_VDEC_HEVCF] = &g12a_vdec_hevcf.hw,
+ [CLKID_SYS1_PLL_DCO] = &g12b_sys1_pll_dco.hw,
+ [CLKID_SYS1_PLL] = &g12b_sys1_pll.hw,
+ [CLKID_CPUB_CLK_DYN0_SEL] = &g12b_cpub_clk_dyn0_sel.hw,
+ [CLKID_CPUB_CLK_DYN0_DIV] = &g12b_cpub_clk_dyn0_div.hw,
+ [CLKID_CPUB_CLK_DYN0] = &g12b_cpub_clk_dyn0.hw,
+ [CLKID_CPUB_CLK_DYN1_SEL] = &g12b_cpub_clk_dyn1_sel.hw,
+ [CLKID_CPUB_CLK_DYN1_DIV] = &g12b_cpub_clk_dyn1_div.hw,
+ [CLKID_CPUB_CLK_DYN1] = &g12b_cpub_clk_dyn1.hw,
+ [CLKID_CPUB_CLK_DYN] = &g12b_cpub_clk_dyn.hw,
+ [CLKID_CPUB_CLK] = &g12b_cpub_clk.hw,
+ [NR_CLKS] = NULL,
+ },
+ .num = NR_CLKS,
+};
+
/* Convenience table to populate regmap in .probe */
static struct clk_regmap *const g12a_clk_regmaps[] = {
&g12a_clk81,
@@ -2990,6 +3413,17 @@ static struct clk_regmap *const g12a_clk_regmaps[] = {
&g12a_vdec_hevcf_sel,
&g12a_vdec_hevcf_div,
&g12a_vdec_hevcf,
+ &g12b_cpu_clk,
+ &g12b_sys1_pll_dco,
+ &g12b_sys1_pll,
+ &g12b_cpub_clk_dyn0_sel,
+ &g12b_cpub_clk_dyn0_div,
+ &g12b_cpub_clk_dyn0,
+ &g12b_cpub_clk_dyn1_sel,
+ &g12b_cpub_clk_dyn1_div,
+ &g12b_cpub_clk_dyn1,
+ &g12b_cpub_clk_dyn,
+ &g12b_cpub_clk,
};
static const struct reg_sequence g12a_init_regs[] = {
@@ -3004,8 +3438,15 @@ static const struct meson_eeclkc_data g12a_clkc_data = {
.init_count = ARRAY_SIZE(g12a_init_regs),
};
+static const struct meson_eeclkc_data g12b_clkc_data = {
+ .regmap_clks = g12a_clk_regmaps,
+ .regmap_clk_num = ARRAY_SIZE(g12a_clk_regmaps),
+ .hw_onecell_data = &g12b_hw_onecell_data
+};
+
static const struct of_device_id clkc_match_table[] = {
{ .compatible = "amlogic,g12a-clkc", .data = &g12a_clkc_data },
+ { .compatible = "amlogic,g12b-clkc", .data = &g12b_clkc_data },
{}
};
diff --git a/drivers/clk/meson/g12a.h b/drivers/clk/meson/g12a.h
index 39c41af70804..efe3f71edc8b 100644
--- a/drivers/clk/meson/g12a.h
+++ b/drivers/clk/meson/g12a.h
@@ -69,6 +69,7 @@
#define HHI_VDEC4_CLK_CNTL 0x1EC
#define HHI_HDCP22_CLK_CNTL 0x1F0
#define HHI_VAPBCLK_CNTL 0x1F4
+#define HHI_SYS_CPUB_CLK_CNTL 0x208
#define HHI_VPU_CLKB_CNTL 0x20C
#define HHI_GEN_CLK_CNTL 0x228
#define HHI_VDIN_MEAS_CLK_CNTL 0x250
@@ -102,6 +103,13 @@
#define HHI_HDMI_PLL_CNTL5 0x334
#define HHI_HDMI_PLL_CNTL6 0x338
#define HHI_SPICC_CLK_CNTL 0x3dc
+#define HHI_SYS1_PLL_CNTL0 0x380
+#define HHI_SYS1_PLL_CNTL1 0x384
+#define HHI_SYS1_PLL_CNTL2 0x388
+#define HHI_SYS1_PLL_CNTL3 0x38c
+#define HHI_SYS1_PLL_CNTL4 0x390
+#define HHI_SYS1_PLL_CNTL5 0x394
+#define HHI_SYS1_PLL_CNTL6 0x398
/*
* CLKID index values
@@ -195,8 +203,18 @@
#define CLKID_VDEC_HEVC_DIV 206
#define CLKID_VDEC_HEVCF_SEL 208
#define CLKID_VDEC_HEVCF_DIV 209
+#define CLKID_SYS1_PLL_DCO 211
+#define CLKID_SYS1_PLL 212
+#define CLKID_CPUB_CLK_DYN0_SEL 213
+#define CLKID_CPUB_CLK_DYN0_DIV 214
+#define CLKID_CPUB_CLK_DYN0 215
+#define CLKID_CPUB_CLK_DYN1_SEL 216
+#define CLKID_CPUB_CLK_DYN1_DIV 217
+#define CLKID_CPUB_CLK_DYN1 218
+#define CLKID_CPUB_CLK_DYN 219
+#define CLKID_CPUB_CLK 220
-#define NR_CLKS 211
+#define NR_CLKS 221
/* include the CLKIDs that have been made part of the DT binding */
#include <dt-bindings/clock/g12a-clkc.h>
--
2.21.0
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 2/6] clk: meson: g12a: Add support for G12B CPUB clocks
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: Neil Armstrong, baylibre-upstreaming, linux-kernel,
linux-amlogic, linux-clk, linux-arm-kernel
This patch support for the specific Amlogic G12B clocks.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12A has additional clocks like for CSI an other components
Here only the cpu clock tree is handled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
drivers/clk/meson/g12a.c | 441 +++++++++++++++++++++++++++++++++++++++
drivers/clk/meson/g12a.h | 20 +-
2 files changed, 460 insertions(+), 1 deletion(-)
diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
index fb698778a614..14aaa02bb621 100644
--- a/drivers/clk/meson/g12a.c
+++ b/drivers/clk/meson/g12a.c
@@ -150,6 +150,57 @@ static struct clk_regmap g12a_sys_pll = {
},
};
+static struct clk_regmap g12b_sys1_pll_dco = {
+ .data = &(struct meson_clk_pll_data){
+ .en = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .m = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 0,
+ .width = 8,
+ },
+ .n = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 10,
+ .width = 5,
+ },
+ .l = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 31,
+ .width = 1,
+ },
+ .rst = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 29,
+ .width = 1,
+ },
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys1_pll_dco",
+ .ops = &meson_clk_pll_ro_ops,
+ .parent_names = (const char *[]){ IN_PREFIX "xtal" },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap g12b_sys1_pll = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = HHI_SYS1_PLL_CNTL0,
+ .shift = 16,
+ .width = 3,
+ .flags = CLK_DIVIDER_POWER_OF_TWO,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys1_pll",
+ .ops = &clk_regmap_divider_ro_ops,
+ .parent_names = (const char *[]){ "sys1_pll_dco" },
+ .num_parents = 1,
+ },
+};
+
static struct clk_regmap g12a_sys_pll_div16_en = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_SYS_CPU_CLK_CNTL1,
@@ -306,6 +357,150 @@ static struct clk_regmap g12a_cpu_clk = {
},
};
+/* Datasheet names this field as "Final_mux_sel" */
+static struct clk_regmap g12b_cpu_clk = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPU_CLK_CNTL0,
+ .mask = 0x1,
+ .shift = 11,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpu_clk",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpu_clk_dyn",
+ "sys1_pll" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "premux0" */
+static struct clk_regmap g12b_cpub_clk_dyn0_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x3,
+ .shift = 0,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn0_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ IN_PREFIX "xtal",
+ "fclk_div2",
+ "fclk_div3" },
+ .num_parents = 3,
+ },
+};
+
+/* Datasheet names this field as "mux0_divn_tcnt" */
+static struct clk_regmap g12b_cpub_clk_dyn0_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .shift = 4,
+ .width = 6,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn0_div",
+ .ops = &clk_regmap_divider_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn0_sel" },
+ .num_parents = 1,
+ },
+};
+
+/* Datasheet names this field as "postmux0" */
+static struct clk_regmap g12b_cpub_clk_dyn0 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 2,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn0",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn0_sel",
+ "cpub_clk_dyn0_div" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "premux1" */
+static struct clk_regmap g12b_cpub_clk_dyn1_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x3,
+ .shift = 16,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn1_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ IN_PREFIX "xtal",
+ "fclk_div2",
+ "fclk_div3" },
+ .num_parents = 3,
+ },
+};
+
+/* Datasheet names this field as "Mux1_divn_tcnt" */
+static struct clk_regmap g12b_cpub_clk_dyn1_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .shift = 20,
+ .width = 6,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn1_div",
+ .ops = &clk_regmap_divider_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn1_sel" },
+ .num_parents = 1,
+ },
+};
+
+/* Datasheet names this field as "postmux1" */
+static struct clk_regmap g12b_cpub_clk_dyn1 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 18,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn1",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn1_sel",
+ "cpub_clk_dyn1_div" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "Final_dyn_mux_sel" */
+static struct clk_regmap g12b_cpub_clk_dyn = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn0",
+ "cpub_clk_dyn1" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "Final_mux_sel" */
+static struct clk_regmap g12b_cpub_clk = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 11,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn",
+ "sys_pll" },
+ .num_parents = 2,
+ },
+};
+
static struct clk_regmap g12a_cpu_clk_div16_en = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_SYS_CPU_CLK_CNTL1,
@@ -2798,6 +2993,234 @@ static struct clk_hw_onecell_data g12a_hw_onecell_data = {
.num = NR_CLKS,
};
+static struct clk_hw_onecell_data g12b_hw_onecell_data = {
+ .hws = {
+ [CLKID_SYS_PLL] = &g12a_sys_pll.hw,
+ [CLKID_FIXED_PLL] = &g12a_fixed_pll.hw,
+ [CLKID_FCLK_DIV2] = &g12a_fclk_div2.hw,
+ [CLKID_FCLK_DIV3] = &g12a_fclk_div3.hw,
+ [CLKID_FCLK_DIV4] = &g12a_fclk_div4.hw,
+ [CLKID_FCLK_DIV5] = &g12a_fclk_div5.hw,
+ [CLKID_FCLK_DIV7] = &g12a_fclk_div7.hw,
+ [CLKID_FCLK_DIV2P5] = &g12a_fclk_div2p5.hw,
+ [CLKID_GP0_PLL] = &g12a_gp0_pll.hw,
+ [CLKID_MPEG_SEL] = &g12a_mpeg_clk_sel.hw,
+ [CLKID_MPEG_DIV] = &g12a_mpeg_clk_div.hw,
+ [CLKID_CLK81] = &g12a_clk81.hw,
+ [CLKID_MPLL0] = &g12a_mpll0.hw,
+ [CLKID_MPLL1] = &g12a_mpll1.hw,
+ [CLKID_MPLL2] = &g12a_mpll2.hw,
+ [CLKID_MPLL3] = &g12a_mpll3.hw,
+ [CLKID_DDR] = &g12a_ddr.hw,
+ [CLKID_DOS] = &g12a_dos.hw,
+ [CLKID_AUDIO_LOCKER] = &g12a_audio_locker.hw,
+ [CLKID_MIPI_DSI_HOST] = &g12a_mipi_dsi_host.hw,
+ [CLKID_ETH_PHY] = &g12a_eth_phy.hw,
+ [CLKID_ISA] = &g12a_isa.hw,
+ [CLKID_PL301] = &g12a_pl301.hw,
+ [CLKID_PERIPHS] = &g12a_periphs.hw,
+ [CLKID_SPICC0] = &g12a_spicc_0.hw,
+ [CLKID_I2C] = &g12a_i2c.hw,
+ [CLKID_SANA] = &g12a_sana.hw,
+ [CLKID_SD] = &g12a_sd.hw,
+ [CLKID_RNG0] = &g12a_rng0.hw,
+ [CLKID_UART0] = &g12a_uart0.hw,
+ [CLKID_SPICC1] = &g12a_spicc_1.hw,
+ [CLKID_HIU_IFACE] = &g12a_hiu_reg.hw,
+ [CLKID_MIPI_DSI_PHY] = &g12a_mipi_dsi_phy.hw,
+ [CLKID_ASSIST_MISC] = &g12a_assist_misc.hw,
+ [CLKID_SD_EMMC_A] = &g12a_emmc_a.hw,
+ [CLKID_SD_EMMC_B] = &g12a_emmc_b.hw,
+ [CLKID_SD_EMMC_C] = &g12a_emmc_c.hw,
+ [CLKID_AUDIO_CODEC] = &g12a_audio_codec.hw,
+ [CLKID_AUDIO] = &g12a_audio.hw,
+ [CLKID_ETH] = &g12a_eth_core.hw,
+ [CLKID_DEMUX] = &g12a_demux.hw,
+ [CLKID_AUDIO_IFIFO] = &g12a_audio_ififo.hw,
+ [CLKID_ADC] = &g12a_adc.hw,
+ [CLKID_UART1] = &g12a_uart1.hw,
+ [CLKID_G2D] = &g12a_g2d.hw,
+ [CLKID_RESET] = &g12a_reset.hw,
+ [CLKID_PCIE_COMB] = &g12a_pcie_comb.hw,
+ [CLKID_PARSER] = &g12a_parser.hw,
+ [CLKID_USB] = &g12a_usb_general.hw,
+ [CLKID_PCIE_PHY] = &g12a_pcie_phy.hw,
+ [CLKID_AHB_ARB0] = &g12a_ahb_arb0.hw,
+ [CLKID_AHB_DATA_BUS] = &g12a_ahb_data_bus.hw,
+ [CLKID_AHB_CTRL_BUS] = &g12a_ahb_ctrl_bus.hw,
+ [CLKID_HTX_HDCP22] = &g12a_htx_hdcp22.hw,
+ [CLKID_HTX_PCLK] = &g12a_htx_pclk.hw,
+ [CLKID_BT656] = &g12a_bt656.hw,
+ [CLKID_USB1_DDR_BRIDGE] = &g12a_usb1_to_ddr.hw,
+ [CLKID_MMC_PCLK] = &g12a_mmc_pclk.hw,
+ [CLKID_UART2] = &g12a_uart2.hw,
+ [CLKID_VPU_INTR] = &g12a_vpu_intr.hw,
+ [CLKID_GIC] = &g12a_gic.hw,
+ [CLKID_SD_EMMC_A_CLK0_SEL] = &g12a_sd_emmc_a_clk0_sel.hw,
+ [CLKID_SD_EMMC_A_CLK0_DIV] = &g12a_sd_emmc_a_clk0_div.hw,
+ [CLKID_SD_EMMC_A_CLK0] = &g12a_sd_emmc_a_clk0.hw,
+ [CLKID_SD_EMMC_B_CLK0_SEL] = &g12a_sd_emmc_b_clk0_sel.hw,
+ [CLKID_SD_EMMC_B_CLK0_DIV] = &g12a_sd_emmc_b_clk0_div.hw,
+ [CLKID_SD_EMMC_B_CLK0] = &g12a_sd_emmc_b_clk0.hw,
+ [CLKID_SD_EMMC_C_CLK0_SEL] = &g12a_sd_emmc_c_clk0_sel.hw,
+ [CLKID_SD_EMMC_C_CLK0_DIV] = &g12a_sd_emmc_c_clk0_div.hw,
+ [CLKID_SD_EMMC_C_CLK0] = &g12a_sd_emmc_c_clk0.hw,
+ [CLKID_MPLL0_DIV] = &g12a_mpll0_div.hw,
+ [CLKID_MPLL1_DIV] = &g12a_mpll1_div.hw,
+ [CLKID_MPLL2_DIV] = &g12a_mpll2_div.hw,
+ [CLKID_MPLL3_DIV] = &g12a_mpll3_div.hw,
+ [CLKID_FCLK_DIV2_DIV] = &g12a_fclk_div2_div.hw,
+ [CLKID_FCLK_DIV3_DIV] = &g12a_fclk_div3_div.hw,
+ [CLKID_FCLK_DIV4_DIV] = &g12a_fclk_div4_div.hw,
+ [CLKID_FCLK_DIV5_DIV] = &g12a_fclk_div5_div.hw,
+ [CLKID_FCLK_DIV7_DIV] = &g12a_fclk_div7_div.hw,
+ [CLKID_FCLK_DIV2P5_DIV] = &g12a_fclk_div2p5_div.hw,
+ [CLKID_HIFI_PLL] = &g12a_hifi_pll.hw,
+ [CLKID_VCLK2_VENCI0] = &g12a_vclk2_venci0.hw,
+ [CLKID_VCLK2_VENCI1] = &g12a_vclk2_venci1.hw,
+ [CLKID_VCLK2_VENCP0] = &g12a_vclk2_vencp0.hw,
+ [CLKID_VCLK2_VENCP1] = &g12a_vclk2_vencp1.hw,
+ [CLKID_VCLK2_VENCT0] = &g12a_vclk2_venct0.hw,
+ [CLKID_VCLK2_VENCT1] = &g12a_vclk2_venct1.hw,
+ [CLKID_VCLK2_OTHER] = &g12a_vclk2_other.hw,
+ [CLKID_VCLK2_ENCI] = &g12a_vclk2_enci.hw,
+ [CLKID_VCLK2_ENCP] = &g12a_vclk2_encp.hw,
+ [CLKID_DAC_CLK] = &g12a_dac_clk.hw,
+ [CLKID_AOCLK] = &g12a_aoclk_gate.hw,
+ [CLKID_IEC958] = &g12a_iec958_gate.hw,
+ [CLKID_ENC480P] = &g12a_enc480p.hw,
+ [CLKID_RNG1] = &g12a_rng1.hw,
+ [CLKID_VCLK2_ENCT] = &g12a_vclk2_enct.hw,
+ [CLKID_VCLK2_ENCL] = &g12a_vclk2_encl.hw,
+ [CLKID_VCLK2_VENCLMMC] = &g12a_vclk2_venclmmc.hw,
+ [CLKID_VCLK2_VENCL] = &g12a_vclk2_vencl.hw,
+ [CLKID_VCLK2_OTHER1] = &g12a_vclk2_other1.hw,
+ [CLKID_FIXED_PLL_DCO] = &g12a_fixed_pll_dco.hw,
+ [CLKID_SYS_PLL_DCO] = &g12a_sys_pll_dco.hw,
+ [CLKID_GP0_PLL_DCO] = &g12a_gp0_pll_dco.hw,
+ [CLKID_HIFI_PLL_DCO] = &g12a_hifi_pll_dco.hw,
+ [CLKID_DMA] = &g12a_dma.hw,
+ [CLKID_EFUSE] = &g12a_efuse.hw,
+ [CLKID_ROM_BOOT] = &g12a_rom_boot.hw,
+ [CLKID_RESET_SEC] = &g12a_reset_sec.hw,
+ [CLKID_SEC_AHB_APB3] = &g12a_sec_ahb_apb3.hw,
+ [CLKID_MPLL_PREDIV] = &g12a_mpll_prediv.hw,
+ [CLKID_VPU_0_SEL] = &g12a_vpu_0_sel.hw,
+ [CLKID_VPU_0_DIV] = &g12a_vpu_0_div.hw,
+ [CLKID_VPU_0] = &g12a_vpu_0.hw,
+ [CLKID_VPU_1_SEL] = &g12a_vpu_1_sel.hw,
+ [CLKID_VPU_1_DIV] = &g12a_vpu_1_div.hw,
+ [CLKID_VPU_1] = &g12a_vpu_1.hw,
+ [CLKID_VPU] = &g12a_vpu.hw,
+ [CLKID_VAPB_0_SEL] = &g12a_vapb_0_sel.hw,
+ [CLKID_VAPB_0_DIV] = &g12a_vapb_0_div.hw,
+ [CLKID_VAPB_0] = &g12a_vapb_0.hw,
+ [CLKID_VAPB_1_SEL] = &g12a_vapb_1_sel.hw,
+ [CLKID_VAPB_1_DIV] = &g12a_vapb_1_div.hw,
+ [CLKID_VAPB_1] = &g12a_vapb_1.hw,
+ [CLKID_VAPB_SEL] = &g12a_vapb_sel.hw,
+ [CLKID_VAPB] = &g12a_vapb.hw,
+ [CLKID_HDMI_PLL_DCO] = &g12a_hdmi_pll_dco.hw,
+ [CLKID_HDMI_PLL_OD] = &g12a_hdmi_pll_od.hw,
+ [CLKID_HDMI_PLL_OD2] = &g12a_hdmi_pll_od2.hw,
+ [CLKID_HDMI_PLL] = &g12a_hdmi_pll.hw,
+ [CLKID_VID_PLL] = &g12a_vid_pll_div.hw,
+ [CLKID_VID_PLL_SEL] = &g12a_vid_pll_sel.hw,
+ [CLKID_VID_PLL_DIV] = &g12a_vid_pll.hw,
+ [CLKID_VCLK_SEL] = &g12a_vclk_sel.hw,
+ [CLKID_VCLK2_SEL] = &g12a_vclk2_sel.hw,
+ [CLKID_VCLK_INPUT] = &g12a_vclk_input.hw,
+ [CLKID_VCLK2_INPUT] = &g12a_vclk2_input.hw,
+ [CLKID_VCLK_DIV] = &g12a_vclk_div.hw,
+ [CLKID_VCLK2_DIV] = &g12a_vclk2_div.hw,
+ [CLKID_VCLK] = &g12a_vclk.hw,
+ [CLKID_VCLK2] = &g12a_vclk2.hw,
+ [CLKID_VCLK_DIV1] = &g12a_vclk_div1.hw,
+ [CLKID_VCLK_DIV2_EN] = &g12a_vclk_div2_en.hw,
+ [CLKID_VCLK_DIV4_EN] = &g12a_vclk_div4_en.hw,
+ [CLKID_VCLK_DIV6_EN] = &g12a_vclk_div6_en.hw,
+ [CLKID_VCLK_DIV12_EN] = &g12a_vclk_div12_en.hw,
+ [CLKID_VCLK2_DIV1] = &g12a_vclk2_div1.hw,
+ [CLKID_VCLK2_DIV2_EN] = &g12a_vclk2_div2_en.hw,
+ [CLKID_VCLK2_DIV4_EN] = &g12a_vclk2_div4_en.hw,
+ [CLKID_VCLK2_DIV6_EN] = &g12a_vclk2_div6_en.hw,
+ [CLKID_VCLK2_DIV12_EN] = &g12a_vclk2_div12_en.hw,
+ [CLKID_VCLK_DIV2] = &g12a_vclk_div2.hw,
+ [CLKID_VCLK_DIV4] = &g12a_vclk_div4.hw,
+ [CLKID_VCLK_DIV6] = &g12a_vclk_div6.hw,
+ [CLKID_VCLK_DIV12] = &g12a_vclk_div12.hw,
+ [CLKID_VCLK2_DIV2] = &g12a_vclk2_div2.hw,
+ [CLKID_VCLK2_DIV4] = &g12a_vclk2_div4.hw,
+ [CLKID_VCLK2_DIV6] = &g12a_vclk2_div6.hw,
+ [CLKID_VCLK2_DIV12] = &g12a_vclk2_div12.hw,
+ [CLKID_CTS_ENCI_SEL] = &g12a_cts_enci_sel.hw,
+ [CLKID_CTS_ENCP_SEL] = &g12a_cts_encp_sel.hw,
+ [CLKID_CTS_VDAC_SEL] = &g12a_cts_vdac_sel.hw,
+ [CLKID_HDMI_TX_SEL] = &g12a_hdmi_tx_sel.hw,
+ [CLKID_CTS_ENCI] = &g12a_cts_enci.hw,
+ [CLKID_CTS_ENCP] = &g12a_cts_encp.hw,
+ [CLKID_CTS_VDAC] = &g12a_cts_vdac.hw,
+ [CLKID_HDMI_TX] = &g12a_hdmi_tx.hw,
+ [CLKID_HDMI_SEL] = &g12a_hdmi_sel.hw,
+ [CLKID_HDMI_DIV] = &g12a_hdmi_div.hw,
+ [CLKID_HDMI] = &g12a_hdmi.hw,
+ [CLKID_MALI_0_SEL] = &g12a_mali_0_sel.hw,
+ [CLKID_MALI_0_DIV] = &g12a_mali_0_div.hw,
+ [CLKID_MALI_0] = &g12a_mali_0.hw,
+ [CLKID_MALI_1_SEL] = &g12a_mali_1_sel.hw,
+ [CLKID_MALI_1_DIV] = &g12a_mali_1_div.hw,
+ [CLKID_MALI_1] = &g12a_mali_1.hw,
+ [CLKID_MALI] = &g12a_mali.hw,
+ [CLKID_MPLL_5OM_DIV] = &g12a_mpll_50m_div.hw,
+ [CLKID_MPLL_5OM] = &g12a_mpll_50m.hw,
+ [CLKID_SYS_PLL_DIV16_EN] = &g12a_sys_pll_div16_en.hw,
+ [CLKID_SYS_PLL_DIV16] = &g12a_sys_pll_div16.hw,
+ [CLKID_CPU_CLK_DYN0_SEL] = &g12a_cpu_clk_dyn0_sel.hw,
+ [CLKID_CPU_CLK_DYN0_DIV] = &g12a_cpu_clk_dyn0_div.hw,
+ [CLKID_CPU_CLK_DYN0] = &g12a_cpu_clk_dyn0.hw,
+ [CLKID_CPU_CLK_DYN1_SEL] = &g12a_cpu_clk_dyn1_sel.hw,
+ [CLKID_CPU_CLK_DYN1_DIV] = &g12a_cpu_clk_dyn1_div.hw,
+ [CLKID_CPU_CLK_DYN1] = &g12a_cpu_clk_dyn1.hw,
+ [CLKID_CPU_CLK_DYN] = &g12a_cpu_clk_dyn.hw,
+ [CLKID_CPU_CLK] = &g12b_cpu_clk.hw,
+ [CLKID_CPU_CLK_DIV16_EN] = &g12a_cpu_clk_div16_en.hw,
+ [CLKID_CPU_CLK_DIV16] = &g12a_cpu_clk_div16.hw,
+ [CLKID_CPU_CLK_APB_DIV] = &g12a_cpu_clk_apb_div.hw,
+ [CLKID_CPU_CLK_APB] = &g12a_cpu_clk_apb.hw,
+ [CLKID_CPU_CLK_ATB_DIV] = &g12a_cpu_clk_atb_div.hw,
+ [CLKID_CPU_CLK_ATB] = &g12a_cpu_clk_atb.hw,
+ [CLKID_CPU_CLK_AXI_DIV] = &g12a_cpu_clk_axi_div.hw,
+ [CLKID_CPU_CLK_AXI] = &g12a_cpu_clk_axi.hw,
+ [CLKID_CPU_CLK_TRACE_DIV] = &g12a_cpu_clk_trace_div.hw,
+ [CLKID_CPU_CLK_TRACE] = &g12a_cpu_clk_trace.hw,
+ [CLKID_PCIE_PLL_DCO] = &g12a_pcie_pll_dco.hw,
+ [CLKID_PCIE_PLL_DCO_DIV2] = &g12a_pcie_pll_dco_div2.hw,
+ [CLKID_PCIE_PLL_OD] = &g12a_pcie_pll_od.hw,
+ [CLKID_PCIE_PLL] = &g12a_pcie_pll.hw,
+ [CLKID_VDEC_1_SEL] = &g12a_vdec_1_sel.hw,
+ [CLKID_VDEC_1_DIV] = &g12a_vdec_1_div.hw,
+ [CLKID_VDEC_1] = &g12a_vdec_1.hw,
+ [CLKID_VDEC_HEVC_SEL] = &g12a_vdec_hevc_sel.hw,
+ [CLKID_VDEC_HEVC_DIV] = &g12a_vdec_hevc_div.hw,
+ [CLKID_VDEC_HEVC] = &g12a_vdec_hevc.hw,
+ [CLKID_VDEC_HEVCF_SEL] = &g12a_vdec_hevcf_sel.hw,
+ [CLKID_VDEC_HEVCF_DIV] = &g12a_vdec_hevcf_div.hw,
+ [CLKID_VDEC_HEVCF] = &g12a_vdec_hevcf.hw,
+ [CLKID_SYS1_PLL_DCO] = &g12b_sys1_pll_dco.hw,
+ [CLKID_SYS1_PLL] = &g12b_sys1_pll.hw,
+ [CLKID_CPUB_CLK_DYN0_SEL] = &g12b_cpub_clk_dyn0_sel.hw,
+ [CLKID_CPUB_CLK_DYN0_DIV] = &g12b_cpub_clk_dyn0_div.hw,
+ [CLKID_CPUB_CLK_DYN0] = &g12b_cpub_clk_dyn0.hw,
+ [CLKID_CPUB_CLK_DYN1_SEL] = &g12b_cpub_clk_dyn1_sel.hw,
+ [CLKID_CPUB_CLK_DYN1_DIV] = &g12b_cpub_clk_dyn1_div.hw,
+ [CLKID_CPUB_CLK_DYN1] = &g12b_cpub_clk_dyn1.hw,
+ [CLKID_CPUB_CLK_DYN] = &g12b_cpub_clk_dyn.hw,
+ [CLKID_CPUB_CLK] = &g12b_cpub_clk.hw,
+ [NR_CLKS] = NULL,
+ },
+ .num = NR_CLKS,
+};
+
/* Convenience table to populate regmap in .probe */
static struct clk_regmap *const g12a_clk_regmaps[] = {
&g12a_clk81,
@@ -2990,6 +3413,17 @@ static struct clk_regmap *const g12a_clk_regmaps[] = {
&g12a_vdec_hevcf_sel,
&g12a_vdec_hevcf_div,
&g12a_vdec_hevcf,
+ &g12b_cpu_clk,
+ &g12b_sys1_pll_dco,
+ &g12b_sys1_pll,
+ &g12b_cpub_clk_dyn0_sel,
+ &g12b_cpub_clk_dyn0_div,
+ &g12b_cpub_clk_dyn0,
+ &g12b_cpub_clk_dyn1_sel,
+ &g12b_cpub_clk_dyn1_div,
+ &g12b_cpub_clk_dyn1,
+ &g12b_cpub_clk_dyn,
+ &g12b_cpub_clk,
};
static const struct reg_sequence g12a_init_regs[] = {
@@ -3004,8 +3438,15 @@ static const struct meson_eeclkc_data g12a_clkc_data = {
.init_count = ARRAY_SIZE(g12a_init_regs),
};
+static const struct meson_eeclkc_data g12b_clkc_data = {
+ .regmap_clks = g12a_clk_regmaps,
+ .regmap_clk_num = ARRAY_SIZE(g12a_clk_regmaps),
+ .hw_onecell_data = &g12b_hw_onecell_data
+};
+
static const struct of_device_id clkc_match_table[] = {
{ .compatible = "amlogic,g12a-clkc", .data = &g12a_clkc_data },
+ { .compatible = "amlogic,g12b-clkc", .data = &g12b_clkc_data },
{}
};
diff --git a/drivers/clk/meson/g12a.h b/drivers/clk/meson/g12a.h
index 39c41af70804..efe3f71edc8b 100644
--- a/drivers/clk/meson/g12a.h
+++ b/drivers/clk/meson/g12a.h
@@ -69,6 +69,7 @@
#define HHI_VDEC4_CLK_CNTL 0x1EC
#define HHI_HDCP22_CLK_CNTL 0x1F0
#define HHI_VAPBCLK_CNTL 0x1F4
+#define HHI_SYS_CPUB_CLK_CNTL 0x208
#define HHI_VPU_CLKB_CNTL 0x20C
#define HHI_GEN_CLK_CNTL 0x228
#define HHI_VDIN_MEAS_CLK_CNTL 0x250
@@ -102,6 +103,13 @@
#define HHI_HDMI_PLL_CNTL5 0x334
#define HHI_HDMI_PLL_CNTL6 0x338
#define HHI_SPICC_CLK_CNTL 0x3dc
+#define HHI_SYS1_PLL_CNTL0 0x380
+#define HHI_SYS1_PLL_CNTL1 0x384
+#define HHI_SYS1_PLL_CNTL2 0x388
+#define HHI_SYS1_PLL_CNTL3 0x38c
+#define HHI_SYS1_PLL_CNTL4 0x390
+#define HHI_SYS1_PLL_CNTL5 0x394
+#define HHI_SYS1_PLL_CNTL6 0x398
/*
* CLKID index values
@@ -195,8 +203,18 @@
#define CLKID_VDEC_HEVC_DIV 206
#define CLKID_VDEC_HEVCF_SEL 208
#define CLKID_VDEC_HEVCF_DIV 209
+#define CLKID_SYS1_PLL_DCO 211
+#define CLKID_SYS1_PLL 212
+#define CLKID_CPUB_CLK_DYN0_SEL 213
+#define CLKID_CPUB_CLK_DYN0_DIV 214
+#define CLKID_CPUB_CLK_DYN0 215
+#define CLKID_CPUB_CLK_DYN1_SEL 216
+#define CLKID_CPUB_CLK_DYN1_DIV 217
+#define CLKID_CPUB_CLK_DYN1 218
+#define CLKID_CPUB_CLK_DYN 219
+#define CLKID_CPUB_CLK 220
-#define NR_CLKS 211
+#define NR_CLKS 221
/* include the CLKIDs that have been made part of the DT binding */
#include <dt-bindings/clock/g12a-clkc.h>
--
2.21.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 2/6] clk: meson: g12a: Add support for G12B CPUB clocks
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: Neil Armstrong, baylibre-upstreaming, linux-kernel,
linux-amlogic, linux-clk, linux-arm-kernel
This patch support for the specific Amlogic G12B clocks.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12A has additional clocks like for CSI an other components
Here only the cpu clock tree is handled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
drivers/clk/meson/g12a.c | 441 +++++++++++++++++++++++++++++++++++++++
drivers/clk/meson/g12a.h | 20 +-
2 files changed, 460 insertions(+), 1 deletion(-)
diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
index fb698778a614..14aaa02bb621 100644
--- a/drivers/clk/meson/g12a.c
+++ b/drivers/clk/meson/g12a.c
@@ -150,6 +150,57 @@ static struct clk_regmap g12a_sys_pll = {
},
};
+static struct clk_regmap g12b_sys1_pll_dco = {
+ .data = &(struct meson_clk_pll_data){
+ .en = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .m = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 0,
+ .width = 8,
+ },
+ .n = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 10,
+ .width = 5,
+ },
+ .l = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 31,
+ .width = 1,
+ },
+ .rst = {
+ .reg_off = HHI_SYS1_PLL_CNTL0,
+ .shift = 29,
+ .width = 1,
+ },
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys1_pll_dco",
+ .ops = &meson_clk_pll_ro_ops,
+ .parent_names = (const char *[]){ IN_PREFIX "xtal" },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap g12b_sys1_pll = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = HHI_SYS1_PLL_CNTL0,
+ .shift = 16,
+ .width = 3,
+ .flags = CLK_DIVIDER_POWER_OF_TWO,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys1_pll",
+ .ops = &clk_regmap_divider_ro_ops,
+ .parent_names = (const char *[]){ "sys1_pll_dco" },
+ .num_parents = 1,
+ },
+};
+
static struct clk_regmap g12a_sys_pll_div16_en = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_SYS_CPU_CLK_CNTL1,
@@ -306,6 +357,150 @@ static struct clk_regmap g12a_cpu_clk = {
},
};
+/* Datasheet names this field as "Final_mux_sel" */
+static struct clk_regmap g12b_cpu_clk = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPU_CLK_CNTL0,
+ .mask = 0x1,
+ .shift = 11,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpu_clk",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpu_clk_dyn",
+ "sys1_pll" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "premux0" */
+static struct clk_regmap g12b_cpub_clk_dyn0_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x3,
+ .shift = 0,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn0_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ IN_PREFIX "xtal",
+ "fclk_div2",
+ "fclk_div3" },
+ .num_parents = 3,
+ },
+};
+
+/* Datasheet names this field as "mux0_divn_tcnt" */
+static struct clk_regmap g12b_cpub_clk_dyn0_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .shift = 4,
+ .width = 6,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn0_div",
+ .ops = &clk_regmap_divider_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn0_sel" },
+ .num_parents = 1,
+ },
+};
+
+/* Datasheet names this field as "postmux0" */
+static struct clk_regmap g12b_cpub_clk_dyn0 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 2,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn0",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn0_sel",
+ "cpub_clk_dyn0_div" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "premux1" */
+static struct clk_regmap g12b_cpub_clk_dyn1_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x3,
+ .shift = 16,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn1_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ IN_PREFIX "xtal",
+ "fclk_div2",
+ "fclk_div3" },
+ .num_parents = 3,
+ },
+};
+
+/* Datasheet names this field as "Mux1_divn_tcnt" */
+static struct clk_regmap g12b_cpub_clk_dyn1_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .shift = 20,
+ .width = 6,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn1_div",
+ .ops = &clk_regmap_divider_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn1_sel" },
+ .num_parents = 1,
+ },
+};
+
+/* Datasheet names this field as "postmux1" */
+static struct clk_regmap g12b_cpub_clk_dyn1 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 18,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn1",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn1_sel",
+ "cpub_clk_dyn1_div" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "Final_dyn_mux_sel" */
+static struct clk_regmap g12b_cpub_clk_dyn = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk_dyn",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn0",
+ "cpub_clk_dyn1" },
+ .num_parents = 2,
+ },
+};
+
+/* Datasheet names this field as "Final_mux_sel" */
+static struct clk_regmap g12b_cpub_clk = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = HHI_SYS_CPUB_CLK_CNTL,
+ .mask = 0x1,
+ .shift = 11,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cpub_clk",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_names = (const char *[]){ "cpub_clk_dyn",
+ "sys_pll" },
+ .num_parents = 2,
+ },
+};
+
static struct clk_regmap g12a_cpu_clk_div16_en = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_SYS_CPU_CLK_CNTL1,
@@ -2798,6 +2993,234 @@ static struct clk_hw_onecell_data g12a_hw_onecell_data = {
.num = NR_CLKS,
};
+static struct clk_hw_onecell_data g12b_hw_onecell_data = {
+ .hws = {
+ [CLKID_SYS_PLL] = &g12a_sys_pll.hw,
+ [CLKID_FIXED_PLL] = &g12a_fixed_pll.hw,
+ [CLKID_FCLK_DIV2] = &g12a_fclk_div2.hw,
+ [CLKID_FCLK_DIV3] = &g12a_fclk_div3.hw,
+ [CLKID_FCLK_DIV4] = &g12a_fclk_div4.hw,
+ [CLKID_FCLK_DIV5] = &g12a_fclk_div5.hw,
+ [CLKID_FCLK_DIV7] = &g12a_fclk_div7.hw,
+ [CLKID_FCLK_DIV2P5] = &g12a_fclk_div2p5.hw,
+ [CLKID_GP0_PLL] = &g12a_gp0_pll.hw,
+ [CLKID_MPEG_SEL] = &g12a_mpeg_clk_sel.hw,
+ [CLKID_MPEG_DIV] = &g12a_mpeg_clk_div.hw,
+ [CLKID_CLK81] = &g12a_clk81.hw,
+ [CLKID_MPLL0] = &g12a_mpll0.hw,
+ [CLKID_MPLL1] = &g12a_mpll1.hw,
+ [CLKID_MPLL2] = &g12a_mpll2.hw,
+ [CLKID_MPLL3] = &g12a_mpll3.hw,
+ [CLKID_DDR] = &g12a_ddr.hw,
+ [CLKID_DOS] = &g12a_dos.hw,
+ [CLKID_AUDIO_LOCKER] = &g12a_audio_locker.hw,
+ [CLKID_MIPI_DSI_HOST] = &g12a_mipi_dsi_host.hw,
+ [CLKID_ETH_PHY] = &g12a_eth_phy.hw,
+ [CLKID_ISA] = &g12a_isa.hw,
+ [CLKID_PL301] = &g12a_pl301.hw,
+ [CLKID_PERIPHS] = &g12a_periphs.hw,
+ [CLKID_SPICC0] = &g12a_spicc_0.hw,
+ [CLKID_I2C] = &g12a_i2c.hw,
+ [CLKID_SANA] = &g12a_sana.hw,
+ [CLKID_SD] = &g12a_sd.hw,
+ [CLKID_RNG0] = &g12a_rng0.hw,
+ [CLKID_UART0] = &g12a_uart0.hw,
+ [CLKID_SPICC1] = &g12a_spicc_1.hw,
+ [CLKID_HIU_IFACE] = &g12a_hiu_reg.hw,
+ [CLKID_MIPI_DSI_PHY] = &g12a_mipi_dsi_phy.hw,
+ [CLKID_ASSIST_MISC] = &g12a_assist_misc.hw,
+ [CLKID_SD_EMMC_A] = &g12a_emmc_a.hw,
+ [CLKID_SD_EMMC_B] = &g12a_emmc_b.hw,
+ [CLKID_SD_EMMC_C] = &g12a_emmc_c.hw,
+ [CLKID_AUDIO_CODEC] = &g12a_audio_codec.hw,
+ [CLKID_AUDIO] = &g12a_audio.hw,
+ [CLKID_ETH] = &g12a_eth_core.hw,
+ [CLKID_DEMUX] = &g12a_demux.hw,
+ [CLKID_AUDIO_IFIFO] = &g12a_audio_ififo.hw,
+ [CLKID_ADC] = &g12a_adc.hw,
+ [CLKID_UART1] = &g12a_uart1.hw,
+ [CLKID_G2D] = &g12a_g2d.hw,
+ [CLKID_RESET] = &g12a_reset.hw,
+ [CLKID_PCIE_COMB] = &g12a_pcie_comb.hw,
+ [CLKID_PARSER] = &g12a_parser.hw,
+ [CLKID_USB] = &g12a_usb_general.hw,
+ [CLKID_PCIE_PHY] = &g12a_pcie_phy.hw,
+ [CLKID_AHB_ARB0] = &g12a_ahb_arb0.hw,
+ [CLKID_AHB_DATA_BUS] = &g12a_ahb_data_bus.hw,
+ [CLKID_AHB_CTRL_BUS] = &g12a_ahb_ctrl_bus.hw,
+ [CLKID_HTX_HDCP22] = &g12a_htx_hdcp22.hw,
+ [CLKID_HTX_PCLK] = &g12a_htx_pclk.hw,
+ [CLKID_BT656] = &g12a_bt656.hw,
+ [CLKID_USB1_DDR_BRIDGE] = &g12a_usb1_to_ddr.hw,
+ [CLKID_MMC_PCLK] = &g12a_mmc_pclk.hw,
+ [CLKID_UART2] = &g12a_uart2.hw,
+ [CLKID_VPU_INTR] = &g12a_vpu_intr.hw,
+ [CLKID_GIC] = &g12a_gic.hw,
+ [CLKID_SD_EMMC_A_CLK0_SEL] = &g12a_sd_emmc_a_clk0_sel.hw,
+ [CLKID_SD_EMMC_A_CLK0_DIV] = &g12a_sd_emmc_a_clk0_div.hw,
+ [CLKID_SD_EMMC_A_CLK0] = &g12a_sd_emmc_a_clk0.hw,
+ [CLKID_SD_EMMC_B_CLK0_SEL] = &g12a_sd_emmc_b_clk0_sel.hw,
+ [CLKID_SD_EMMC_B_CLK0_DIV] = &g12a_sd_emmc_b_clk0_div.hw,
+ [CLKID_SD_EMMC_B_CLK0] = &g12a_sd_emmc_b_clk0.hw,
+ [CLKID_SD_EMMC_C_CLK0_SEL] = &g12a_sd_emmc_c_clk0_sel.hw,
+ [CLKID_SD_EMMC_C_CLK0_DIV] = &g12a_sd_emmc_c_clk0_div.hw,
+ [CLKID_SD_EMMC_C_CLK0] = &g12a_sd_emmc_c_clk0.hw,
+ [CLKID_MPLL0_DIV] = &g12a_mpll0_div.hw,
+ [CLKID_MPLL1_DIV] = &g12a_mpll1_div.hw,
+ [CLKID_MPLL2_DIV] = &g12a_mpll2_div.hw,
+ [CLKID_MPLL3_DIV] = &g12a_mpll3_div.hw,
+ [CLKID_FCLK_DIV2_DIV] = &g12a_fclk_div2_div.hw,
+ [CLKID_FCLK_DIV3_DIV] = &g12a_fclk_div3_div.hw,
+ [CLKID_FCLK_DIV4_DIV] = &g12a_fclk_div4_div.hw,
+ [CLKID_FCLK_DIV5_DIV] = &g12a_fclk_div5_div.hw,
+ [CLKID_FCLK_DIV7_DIV] = &g12a_fclk_div7_div.hw,
+ [CLKID_FCLK_DIV2P5_DIV] = &g12a_fclk_div2p5_div.hw,
+ [CLKID_HIFI_PLL] = &g12a_hifi_pll.hw,
+ [CLKID_VCLK2_VENCI0] = &g12a_vclk2_venci0.hw,
+ [CLKID_VCLK2_VENCI1] = &g12a_vclk2_venci1.hw,
+ [CLKID_VCLK2_VENCP0] = &g12a_vclk2_vencp0.hw,
+ [CLKID_VCLK2_VENCP1] = &g12a_vclk2_vencp1.hw,
+ [CLKID_VCLK2_VENCT0] = &g12a_vclk2_venct0.hw,
+ [CLKID_VCLK2_VENCT1] = &g12a_vclk2_venct1.hw,
+ [CLKID_VCLK2_OTHER] = &g12a_vclk2_other.hw,
+ [CLKID_VCLK2_ENCI] = &g12a_vclk2_enci.hw,
+ [CLKID_VCLK2_ENCP] = &g12a_vclk2_encp.hw,
+ [CLKID_DAC_CLK] = &g12a_dac_clk.hw,
+ [CLKID_AOCLK] = &g12a_aoclk_gate.hw,
+ [CLKID_IEC958] = &g12a_iec958_gate.hw,
+ [CLKID_ENC480P] = &g12a_enc480p.hw,
+ [CLKID_RNG1] = &g12a_rng1.hw,
+ [CLKID_VCLK2_ENCT] = &g12a_vclk2_enct.hw,
+ [CLKID_VCLK2_ENCL] = &g12a_vclk2_encl.hw,
+ [CLKID_VCLK2_VENCLMMC] = &g12a_vclk2_venclmmc.hw,
+ [CLKID_VCLK2_VENCL] = &g12a_vclk2_vencl.hw,
+ [CLKID_VCLK2_OTHER1] = &g12a_vclk2_other1.hw,
+ [CLKID_FIXED_PLL_DCO] = &g12a_fixed_pll_dco.hw,
+ [CLKID_SYS_PLL_DCO] = &g12a_sys_pll_dco.hw,
+ [CLKID_GP0_PLL_DCO] = &g12a_gp0_pll_dco.hw,
+ [CLKID_HIFI_PLL_DCO] = &g12a_hifi_pll_dco.hw,
+ [CLKID_DMA] = &g12a_dma.hw,
+ [CLKID_EFUSE] = &g12a_efuse.hw,
+ [CLKID_ROM_BOOT] = &g12a_rom_boot.hw,
+ [CLKID_RESET_SEC] = &g12a_reset_sec.hw,
+ [CLKID_SEC_AHB_APB3] = &g12a_sec_ahb_apb3.hw,
+ [CLKID_MPLL_PREDIV] = &g12a_mpll_prediv.hw,
+ [CLKID_VPU_0_SEL] = &g12a_vpu_0_sel.hw,
+ [CLKID_VPU_0_DIV] = &g12a_vpu_0_div.hw,
+ [CLKID_VPU_0] = &g12a_vpu_0.hw,
+ [CLKID_VPU_1_SEL] = &g12a_vpu_1_sel.hw,
+ [CLKID_VPU_1_DIV] = &g12a_vpu_1_div.hw,
+ [CLKID_VPU_1] = &g12a_vpu_1.hw,
+ [CLKID_VPU] = &g12a_vpu.hw,
+ [CLKID_VAPB_0_SEL] = &g12a_vapb_0_sel.hw,
+ [CLKID_VAPB_0_DIV] = &g12a_vapb_0_div.hw,
+ [CLKID_VAPB_0] = &g12a_vapb_0.hw,
+ [CLKID_VAPB_1_SEL] = &g12a_vapb_1_sel.hw,
+ [CLKID_VAPB_1_DIV] = &g12a_vapb_1_div.hw,
+ [CLKID_VAPB_1] = &g12a_vapb_1.hw,
+ [CLKID_VAPB_SEL] = &g12a_vapb_sel.hw,
+ [CLKID_VAPB] = &g12a_vapb.hw,
+ [CLKID_HDMI_PLL_DCO] = &g12a_hdmi_pll_dco.hw,
+ [CLKID_HDMI_PLL_OD] = &g12a_hdmi_pll_od.hw,
+ [CLKID_HDMI_PLL_OD2] = &g12a_hdmi_pll_od2.hw,
+ [CLKID_HDMI_PLL] = &g12a_hdmi_pll.hw,
+ [CLKID_VID_PLL] = &g12a_vid_pll_div.hw,
+ [CLKID_VID_PLL_SEL] = &g12a_vid_pll_sel.hw,
+ [CLKID_VID_PLL_DIV] = &g12a_vid_pll.hw,
+ [CLKID_VCLK_SEL] = &g12a_vclk_sel.hw,
+ [CLKID_VCLK2_SEL] = &g12a_vclk2_sel.hw,
+ [CLKID_VCLK_INPUT] = &g12a_vclk_input.hw,
+ [CLKID_VCLK2_INPUT] = &g12a_vclk2_input.hw,
+ [CLKID_VCLK_DIV] = &g12a_vclk_div.hw,
+ [CLKID_VCLK2_DIV] = &g12a_vclk2_div.hw,
+ [CLKID_VCLK] = &g12a_vclk.hw,
+ [CLKID_VCLK2] = &g12a_vclk2.hw,
+ [CLKID_VCLK_DIV1] = &g12a_vclk_div1.hw,
+ [CLKID_VCLK_DIV2_EN] = &g12a_vclk_div2_en.hw,
+ [CLKID_VCLK_DIV4_EN] = &g12a_vclk_div4_en.hw,
+ [CLKID_VCLK_DIV6_EN] = &g12a_vclk_div6_en.hw,
+ [CLKID_VCLK_DIV12_EN] = &g12a_vclk_div12_en.hw,
+ [CLKID_VCLK2_DIV1] = &g12a_vclk2_div1.hw,
+ [CLKID_VCLK2_DIV2_EN] = &g12a_vclk2_div2_en.hw,
+ [CLKID_VCLK2_DIV4_EN] = &g12a_vclk2_div4_en.hw,
+ [CLKID_VCLK2_DIV6_EN] = &g12a_vclk2_div6_en.hw,
+ [CLKID_VCLK2_DIV12_EN] = &g12a_vclk2_div12_en.hw,
+ [CLKID_VCLK_DIV2] = &g12a_vclk_div2.hw,
+ [CLKID_VCLK_DIV4] = &g12a_vclk_div4.hw,
+ [CLKID_VCLK_DIV6] = &g12a_vclk_div6.hw,
+ [CLKID_VCLK_DIV12] = &g12a_vclk_div12.hw,
+ [CLKID_VCLK2_DIV2] = &g12a_vclk2_div2.hw,
+ [CLKID_VCLK2_DIV4] = &g12a_vclk2_div4.hw,
+ [CLKID_VCLK2_DIV6] = &g12a_vclk2_div6.hw,
+ [CLKID_VCLK2_DIV12] = &g12a_vclk2_div12.hw,
+ [CLKID_CTS_ENCI_SEL] = &g12a_cts_enci_sel.hw,
+ [CLKID_CTS_ENCP_SEL] = &g12a_cts_encp_sel.hw,
+ [CLKID_CTS_VDAC_SEL] = &g12a_cts_vdac_sel.hw,
+ [CLKID_HDMI_TX_SEL] = &g12a_hdmi_tx_sel.hw,
+ [CLKID_CTS_ENCI] = &g12a_cts_enci.hw,
+ [CLKID_CTS_ENCP] = &g12a_cts_encp.hw,
+ [CLKID_CTS_VDAC] = &g12a_cts_vdac.hw,
+ [CLKID_HDMI_TX] = &g12a_hdmi_tx.hw,
+ [CLKID_HDMI_SEL] = &g12a_hdmi_sel.hw,
+ [CLKID_HDMI_DIV] = &g12a_hdmi_div.hw,
+ [CLKID_HDMI] = &g12a_hdmi.hw,
+ [CLKID_MALI_0_SEL] = &g12a_mali_0_sel.hw,
+ [CLKID_MALI_0_DIV] = &g12a_mali_0_div.hw,
+ [CLKID_MALI_0] = &g12a_mali_0.hw,
+ [CLKID_MALI_1_SEL] = &g12a_mali_1_sel.hw,
+ [CLKID_MALI_1_DIV] = &g12a_mali_1_div.hw,
+ [CLKID_MALI_1] = &g12a_mali_1.hw,
+ [CLKID_MALI] = &g12a_mali.hw,
+ [CLKID_MPLL_5OM_DIV] = &g12a_mpll_50m_div.hw,
+ [CLKID_MPLL_5OM] = &g12a_mpll_50m.hw,
+ [CLKID_SYS_PLL_DIV16_EN] = &g12a_sys_pll_div16_en.hw,
+ [CLKID_SYS_PLL_DIV16] = &g12a_sys_pll_div16.hw,
+ [CLKID_CPU_CLK_DYN0_SEL] = &g12a_cpu_clk_dyn0_sel.hw,
+ [CLKID_CPU_CLK_DYN0_DIV] = &g12a_cpu_clk_dyn0_div.hw,
+ [CLKID_CPU_CLK_DYN0] = &g12a_cpu_clk_dyn0.hw,
+ [CLKID_CPU_CLK_DYN1_SEL] = &g12a_cpu_clk_dyn1_sel.hw,
+ [CLKID_CPU_CLK_DYN1_DIV] = &g12a_cpu_clk_dyn1_div.hw,
+ [CLKID_CPU_CLK_DYN1] = &g12a_cpu_clk_dyn1.hw,
+ [CLKID_CPU_CLK_DYN] = &g12a_cpu_clk_dyn.hw,
+ [CLKID_CPU_CLK] = &g12b_cpu_clk.hw,
+ [CLKID_CPU_CLK_DIV16_EN] = &g12a_cpu_clk_div16_en.hw,
+ [CLKID_CPU_CLK_DIV16] = &g12a_cpu_clk_div16.hw,
+ [CLKID_CPU_CLK_APB_DIV] = &g12a_cpu_clk_apb_div.hw,
+ [CLKID_CPU_CLK_APB] = &g12a_cpu_clk_apb.hw,
+ [CLKID_CPU_CLK_ATB_DIV] = &g12a_cpu_clk_atb_div.hw,
+ [CLKID_CPU_CLK_ATB] = &g12a_cpu_clk_atb.hw,
+ [CLKID_CPU_CLK_AXI_DIV] = &g12a_cpu_clk_axi_div.hw,
+ [CLKID_CPU_CLK_AXI] = &g12a_cpu_clk_axi.hw,
+ [CLKID_CPU_CLK_TRACE_DIV] = &g12a_cpu_clk_trace_div.hw,
+ [CLKID_CPU_CLK_TRACE] = &g12a_cpu_clk_trace.hw,
+ [CLKID_PCIE_PLL_DCO] = &g12a_pcie_pll_dco.hw,
+ [CLKID_PCIE_PLL_DCO_DIV2] = &g12a_pcie_pll_dco_div2.hw,
+ [CLKID_PCIE_PLL_OD] = &g12a_pcie_pll_od.hw,
+ [CLKID_PCIE_PLL] = &g12a_pcie_pll.hw,
+ [CLKID_VDEC_1_SEL] = &g12a_vdec_1_sel.hw,
+ [CLKID_VDEC_1_DIV] = &g12a_vdec_1_div.hw,
+ [CLKID_VDEC_1] = &g12a_vdec_1.hw,
+ [CLKID_VDEC_HEVC_SEL] = &g12a_vdec_hevc_sel.hw,
+ [CLKID_VDEC_HEVC_DIV] = &g12a_vdec_hevc_div.hw,
+ [CLKID_VDEC_HEVC] = &g12a_vdec_hevc.hw,
+ [CLKID_VDEC_HEVCF_SEL] = &g12a_vdec_hevcf_sel.hw,
+ [CLKID_VDEC_HEVCF_DIV] = &g12a_vdec_hevcf_div.hw,
+ [CLKID_VDEC_HEVCF] = &g12a_vdec_hevcf.hw,
+ [CLKID_SYS1_PLL_DCO] = &g12b_sys1_pll_dco.hw,
+ [CLKID_SYS1_PLL] = &g12b_sys1_pll.hw,
+ [CLKID_CPUB_CLK_DYN0_SEL] = &g12b_cpub_clk_dyn0_sel.hw,
+ [CLKID_CPUB_CLK_DYN0_DIV] = &g12b_cpub_clk_dyn0_div.hw,
+ [CLKID_CPUB_CLK_DYN0] = &g12b_cpub_clk_dyn0.hw,
+ [CLKID_CPUB_CLK_DYN1_SEL] = &g12b_cpub_clk_dyn1_sel.hw,
+ [CLKID_CPUB_CLK_DYN1_DIV] = &g12b_cpub_clk_dyn1_div.hw,
+ [CLKID_CPUB_CLK_DYN1] = &g12b_cpub_clk_dyn1.hw,
+ [CLKID_CPUB_CLK_DYN] = &g12b_cpub_clk_dyn.hw,
+ [CLKID_CPUB_CLK] = &g12b_cpub_clk.hw,
+ [NR_CLKS] = NULL,
+ },
+ .num = NR_CLKS,
+};
+
/* Convenience table to populate regmap in .probe */
static struct clk_regmap *const g12a_clk_regmaps[] = {
&g12a_clk81,
@@ -2990,6 +3413,17 @@ static struct clk_regmap *const g12a_clk_regmaps[] = {
&g12a_vdec_hevcf_sel,
&g12a_vdec_hevcf_div,
&g12a_vdec_hevcf,
+ &g12b_cpu_clk,
+ &g12b_sys1_pll_dco,
+ &g12b_sys1_pll,
+ &g12b_cpub_clk_dyn0_sel,
+ &g12b_cpub_clk_dyn0_div,
+ &g12b_cpub_clk_dyn0,
+ &g12b_cpub_clk_dyn1_sel,
+ &g12b_cpub_clk_dyn1_div,
+ &g12b_cpub_clk_dyn1,
+ &g12b_cpub_clk_dyn,
+ &g12b_cpub_clk,
};
static const struct reg_sequence g12a_init_regs[] = {
@@ -3004,8 +3438,15 @@ static const struct meson_eeclkc_data g12a_clkc_data = {
.init_count = ARRAY_SIZE(g12a_init_regs),
};
+static const struct meson_eeclkc_data g12b_clkc_data = {
+ .regmap_clks = g12a_clk_regmaps,
+ .regmap_clk_num = ARRAY_SIZE(g12a_clk_regmaps),
+ .hw_onecell_data = &g12b_hw_onecell_data
+};
+
static const struct of_device_id clkc_match_table[] = {
{ .compatible = "amlogic,g12a-clkc", .data = &g12a_clkc_data },
+ { .compatible = "amlogic,g12b-clkc", .data = &g12b_clkc_data },
{}
};
diff --git a/drivers/clk/meson/g12a.h b/drivers/clk/meson/g12a.h
index 39c41af70804..efe3f71edc8b 100644
--- a/drivers/clk/meson/g12a.h
+++ b/drivers/clk/meson/g12a.h
@@ -69,6 +69,7 @@
#define HHI_VDEC4_CLK_CNTL 0x1EC
#define HHI_HDCP22_CLK_CNTL 0x1F0
#define HHI_VAPBCLK_CNTL 0x1F4
+#define HHI_SYS_CPUB_CLK_CNTL 0x208
#define HHI_VPU_CLKB_CNTL 0x20C
#define HHI_GEN_CLK_CNTL 0x228
#define HHI_VDIN_MEAS_CLK_CNTL 0x250
@@ -102,6 +103,13 @@
#define HHI_HDMI_PLL_CNTL5 0x334
#define HHI_HDMI_PLL_CNTL6 0x338
#define HHI_SPICC_CLK_CNTL 0x3dc
+#define HHI_SYS1_PLL_CNTL0 0x380
+#define HHI_SYS1_PLL_CNTL1 0x384
+#define HHI_SYS1_PLL_CNTL2 0x388
+#define HHI_SYS1_PLL_CNTL3 0x38c
+#define HHI_SYS1_PLL_CNTL4 0x390
+#define HHI_SYS1_PLL_CNTL5 0x394
+#define HHI_SYS1_PLL_CNTL6 0x398
/*
* CLKID index values
@@ -195,8 +203,18 @@
#define CLKID_VDEC_HEVC_DIV 206
#define CLKID_VDEC_HEVCF_SEL 208
#define CLKID_VDEC_HEVCF_DIV 209
+#define CLKID_SYS1_PLL_DCO 211
+#define CLKID_SYS1_PLL 212
+#define CLKID_CPUB_CLK_DYN0_SEL 213
+#define CLKID_CPUB_CLK_DYN0_DIV 214
+#define CLKID_CPUB_CLK_DYN0 215
+#define CLKID_CPUB_CLK_DYN1_SEL 216
+#define CLKID_CPUB_CLK_DYN1_DIV 217
+#define CLKID_CPUB_CLK_DYN1 218
+#define CLKID_CPUB_CLK_DYN 219
+#define CLKID_CPUB_CLK 220
-#define NR_CLKS 211
+#define NR_CLKS 221
/* include the CLKIDs that have been made part of the DT binding */
#include <dt-bindings/clock/g12a-clkc.h>
--
2.21.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 3/6] clk: meson: g12a: mark fclk_div3 as critical
2019-04-04 15:05 ` Neil Armstrong
(?)
@ 2019-04-04 15:05 ` Neil Armstrong
-1 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: baylibre-upstreaming, Neil Armstrong, linux-amlogic,
linux-arm-kernel, linux-kernel, linux-clk
On Amlogic Meson G12b platform, the fclk_div3 seems to be necessary for
the system to operate correctly.
Disabling it cause the entire system to freeze, including peripherals.
This patch patch marks this clock as critical, fixing boot on G12b platforms.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
drivers/clk/meson/g12a.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
index 14aaa02bb621..3554d1172169 100644
--- a/drivers/clk/meson/g12a.c
+++ b/drivers/clk/meson/g12a.c
@@ -1060,6 +1060,16 @@ static struct clk_regmap g12a_fclk_div3 = {
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "fclk_div3_div" },
.num_parents = 1,
+ /*
+ * This clock is used by the resident firmware and is required
+ * by the platform to operate correctly.
+ * Until the following condition are met, we need this clock to
+ * be marked as critical:
+ * a) Mark the clock used by a firmware resource, if possible
+ * b) CCF has a clock hand-off mechanism to make the sure the
+ * clock stays on until the proper driver comes along
+ */
+ .flags = CLK_IS_CRITICAL,
},
};
--
2.21.0
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 3/6] clk: meson: g12a: mark fclk_div3 as critical
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: Neil Armstrong, baylibre-upstreaming, linux-kernel,
linux-amlogic, linux-clk, linux-arm-kernel
On Amlogic Meson G12b platform, the fclk_div3 seems to be necessary for
the system to operate correctly.
Disabling it cause the entire system to freeze, including peripherals.
This patch patch marks this clock as critical, fixing boot on G12b platforms.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
drivers/clk/meson/g12a.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
index 14aaa02bb621..3554d1172169 100644
--- a/drivers/clk/meson/g12a.c
+++ b/drivers/clk/meson/g12a.c
@@ -1060,6 +1060,16 @@ static struct clk_regmap g12a_fclk_div3 = {
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "fclk_div3_div" },
.num_parents = 1,
+ /*
+ * This clock is used by the resident firmware and is required
+ * by the platform to operate correctly.
+ * Until the following condition are met, we need this clock to
+ * be marked as critical:
+ * a) Mark the clock used by a firmware resource, if possible
+ * b) CCF has a clock hand-off mechanism to make the sure the
+ * clock stays on until the proper driver comes along
+ */
+ .flags = CLK_IS_CRITICAL,
},
};
--
2.21.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 3/6] clk: meson: g12a: mark fclk_div3 as critical
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: Neil Armstrong, baylibre-upstreaming, linux-kernel,
linux-amlogic, linux-clk, linux-arm-kernel
On Amlogic Meson G12b platform, the fclk_div3 seems to be necessary for
the system to operate correctly.
Disabling it cause the entire system to freeze, including peripherals.
This patch patch marks this clock as critical, fixing boot on G12b platforms.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
drivers/clk/meson/g12a.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
index 14aaa02bb621..3554d1172169 100644
--- a/drivers/clk/meson/g12a.c
+++ b/drivers/clk/meson/g12a.c
@@ -1060,6 +1060,16 @@ static struct clk_regmap g12a_fclk_div3 = {
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "fclk_div3_div" },
.num_parents = 1,
+ /*
+ * This clock is used by the resident firmware and is required
+ * by the platform to operate correctly.
+ * Until the following condition are met, we need this clock to
+ * be marked as critical:
+ * a) Mark the clock used by a firmware resource, if possible
+ * b) CCF has a clock hand-off mechanism to make the sure the
+ * clock stays on until the proper driver comes along
+ */
+ .flags = CLK_IS_CRITICAL,
},
};
--
2.21.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 4/6] dt-bindings: arm: amlogic: add G12B bindings
2019-04-04 15:05 ` Neil Armstrong
(?)
@ 2019-04-04 15:05 ` Neil Armstrong
-1 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, devicetree, jbrunet
Cc: baylibre-upstreaming, Neil Armstrong, linux-amlogic,
linux-arm-kernel, linux-kernel, Rob Herring
Add compatible for the Amlogic G12B SoC, sharing most of the
features and architecture with the G12A SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/amlogic.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 061f7b98a07f..94bbcc646e10 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -61,6 +61,10 @@ Boards with the Amlogic Meson G12A S905D2 SoC shall have the following propertie
Required root node property:
compatible: "amlogic,g12a";
+Boards with the Amlogic Meson G12B S922X SoC shall have the following properties:
+ Required root node property:
+ compatible: "amlogic,g12b";
+
Board compatible values (alphabetically, grouped by SoC):
- "geniatech,atv1200" (Meson6)
--
2.21.0
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 4/6] dt-bindings: arm: amlogic: add G12B bindings
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, devicetree, jbrunet
Cc: Rob Herring, Neil Armstrong, baylibre-upstreaming, linux-kernel,
linux-amlogic, linux-arm-kernel
Add compatible for the Amlogic G12B SoC, sharing most of the
features and architecture with the G12A SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/amlogic.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 061f7b98a07f..94bbcc646e10 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -61,6 +61,10 @@ Boards with the Amlogic Meson G12A S905D2 SoC shall have the following propertie
Required root node property:
compatible: "amlogic,g12a";
+Boards with the Amlogic Meson G12B S922X SoC shall have the following properties:
+ Required root node property:
+ compatible: "amlogic,g12b";
+
Board compatible values (alphabetically, grouped by SoC):
- "geniatech,atv1200" (Meson6)
--
2.21.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 4/6] dt-bindings: arm: amlogic: add G12B bindings
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, devicetree, jbrunet
Cc: Rob Herring, Neil Armstrong, baylibre-upstreaming, linux-kernel,
linux-amlogic, linux-arm-kernel
Add compatible for the Amlogic G12B SoC, sharing most of the
features and architecture with the G12A SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/amlogic.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 061f7b98a07f..94bbcc646e10 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -61,6 +61,10 @@ Boards with the Amlogic Meson G12A S905D2 SoC shall have the following propertie
Required root node property:
compatible: "amlogic,g12a";
+Boards with the Amlogic Meson G12B S922X SoC shall have the following properties:
+ Required root node property:
+ compatible: "amlogic,g12b";
+
Board compatible values (alphabetically, grouped by SoC):
- "geniatech,atv1200" (Meson6)
--
2.21.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 5/6] dt-bindings: arm: amlogic: add Odroid-N2 binding
2019-04-04 15:05 ` Neil Armstrong
(?)
@ 2019-04-04 15:05 ` Neil Armstrong
-1 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, devicetree, jbrunet
Cc: baylibre-upstreaming, Neil Armstrong, linux-amlogic,
linux-arm-kernel, linux-kernel, Rob Herring
Add compatible for the Amlogic G12B (S922X) SoC based Odroid-N2 SBC
from HardKernel.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/amlogic.txt | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 94bbcc646e10..eff41128268e 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -116,6 +116,8 @@ Board compatible values (alphabetically, grouped by SoC):
- "amediatech,x96-max" (Meson g12a s905x2)
- "seirobotics,sei510" (Meson g12a s905x2)
+ - "hardkernel,odroid-n2" (Meson g12b s922x)
+
Amlogic Meson Firmware registers Interface
------------------------------------------
--
2.21.0
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 5/6] dt-bindings: arm: amlogic: add Odroid-N2 binding
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, devicetree, jbrunet
Cc: Rob Herring, Neil Armstrong, baylibre-upstreaming, linux-kernel,
linux-amlogic, linux-arm-kernel
Add compatible for the Amlogic G12B (S922X) SoC based Odroid-N2 SBC
from HardKernel.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/amlogic.txt | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 94bbcc646e10..eff41128268e 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -116,6 +116,8 @@ Board compatible values (alphabetically, grouped by SoC):
- "amediatech,x96-max" (Meson g12a s905x2)
- "seirobotics,sei510" (Meson g12a s905x2)
+ - "hardkernel,odroid-n2" (Meson g12b s922x)
+
Amlogic Meson Firmware registers Interface
------------------------------------------
--
2.21.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 5/6] dt-bindings: arm: amlogic: add Odroid-N2 binding
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, devicetree, jbrunet
Cc: Rob Herring, Neil Armstrong, baylibre-upstreaming, linux-kernel,
linux-amlogic, linux-arm-kernel
Add compatible for the Amlogic G12B (S922X) SoC based Odroid-N2 SBC
from HardKernel.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/amlogic.txt | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 94bbcc646e10..eff41128268e 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -116,6 +116,8 @@ Board compatible values (alphabetically, grouped by SoC):
- "amediatech,x96-max" (Meson g12a s905x2)
- "seirobotics,sei510" (Meson g12a s905x2)
+ - "hardkernel,odroid-n2" (Meson g12b s922x)
+
Amlogic Meson Firmware registers Interface
------------------------------------------
--
2.21.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 6/6] arm64: dts: meson: Add minimal support for Odroid-N2
2019-04-04 15:05 ` Neil Armstrong
(?)
@ 2019-04-04 15:05 ` Neil Armstrong
-1 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: baylibre-upstreaming, Neil Armstrong, linux-amlogic,
linux-arm-kernel, linux-kernel
This patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC
The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 178 ++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 ++++++++
3 files changed, 261 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index e129c03ced14..07b861fe5fa5 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
new file mode 100644
index 000000000000..9dd6e05cfd0e
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+ compatible = "hardkernel,odroid-n2", "amlogic,g12b";
+ model = "Hardkernel ODROID-N2";
+
+ aliases {
+ serial0 = &uart_AO;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "n2:blue";
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ main_12v: regulator-main_12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vcc_1v8: regulator-vcc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ hub_5v: regulator-hub_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "HUB_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_pwr_en: regulator-usb_pwr_en {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR_EN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&hub_5v>;
+
+ gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vddao_1v8: regulator-vddao_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-always-on;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&gpio {
+ /*
+ * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
+ * to be turned high in order to be detected by the USB Controller
+ * This signal should be handled by a USB specific power sequence
+ * in order to reset the Hub when USB bus is powered down.
+ */
+ usb-hub {
+ gpio-hog;
+ gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-hub-reset";
+ };
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb2_phy0 {
+ phy-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy1 {
+ phy-supply = <&vcc_5v>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
new file mode 100644
index 000000000000..0359539ba884
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12a.dtsi"
+
+/ {
+ compatible = "amlogic,g12b";
+
+ cpus {
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&cpu100>;
+ };
+
+ core1 {
+ cpu = <&cpu101>;
+ };
+
+ core2 {
+ cpu = <&cpu102>;
+ };
+
+ core3 {
+ cpu = <&cpu103>;
+ };
+ };
+ };
+
+ /delete-node/ cpu@2;
+ /delete-node/ cpu@3;
+
+ cpu100: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu101: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu102: cpu@102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x102>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu103: cpu@103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x103>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+ };
+};
+
+&clkc {
+ compatible = "amlogic,g12b-clkc";
+};
--
2.21.0
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 6/6] arm64: dts: meson: Add minimal support for Odroid-N2
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: baylibre-upstreaming, linux-amlogic, linux-kernel,
linux-arm-kernel, Neil Armstrong
This patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC
The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 178 ++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 ++++++++
3 files changed, 261 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index e129c03ced14..07b861fe5fa5 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
new file mode 100644
index 000000000000..9dd6e05cfd0e
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+ compatible = "hardkernel,odroid-n2", "amlogic,g12b";
+ model = "Hardkernel ODROID-N2";
+
+ aliases {
+ serial0 = &uart_AO;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "n2:blue";
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ main_12v: regulator-main_12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vcc_1v8: regulator-vcc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ hub_5v: regulator-hub_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "HUB_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_pwr_en: regulator-usb_pwr_en {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR_EN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&hub_5v>;
+
+ gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vddao_1v8: regulator-vddao_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-always-on;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&gpio {
+ /*
+ * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
+ * to be turned high in order to be detected by the USB Controller
+ * This signal should be handled by a USB specific power sequence
+ * in order to reset the Hub when USB bus is powered down.
+ */
+ usb-hub {
+ gpio-hog;
+ gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-hub-reset";
+ };
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb2_phy0 {
+ phy-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy1 {
+ phy-supply = <&vcc_5v>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
new file mode 100644
index 000000000000..0359539ba884
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12a.dtsi"
+
+/ {
+ compatible = "amlogic,g12b";
+
+ cpus {
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&cpu100>;
+ };
+
+ core1 {
+ cpu = <&cpu101>;
+ };
+
+ core2 {
+ cpu = <&cpu102>;
+ };
+
+ core3 {
+ cpu = <&cpu103>;
+ };
+ };
+ };
+
+ /delete-node/ cpu@2;
+ /delete-node/ cpu@3;
+
+ cpu100: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu101: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu102: cpu@102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x102>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu103: cpu@103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x103>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+ };
+};
+
+&clkc {
+ compatible = "amlogic,g12b-clkc";
+};
--
2.21.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 6/6] arm64: dts: meson: Add minimal support for Odroid-N2
@ 2019-04-04 15:05 ` Neil Armstrong
0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2019-04-04 15:05 UTC (permalink / raw)
To: khilman, jbrunet
Cc: baylibre-upstreaming, linux-amlogic, linux-kernel,
linux-arm-kernel, Neil Armstrong
This patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC
The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 178 ++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 ++++++++
3 files changed, 261 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index e129c03ced14..07b861fe5fa5 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
new file mode 100644
index 000000000000..9dd6e05cfd0e
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+ compatible = "hardkernel,odroid-n2", "amlogic,g12b";
+ model = "Hardkernel ODROID-N2";
+
+ aliases {
+ serial0 = &uart_AO;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "n2:blue";
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ main_12v: regulator-main_12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vcc_1v8: regulator-vcc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ hub_5v: regulator-hub_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "HUB_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_pwr_en: regulator-usb_pwr_en {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR_EN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&hub_5v>;
+
+ gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vddao_1v8: regulator-vddao_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-always-on;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&gpio {
+ /*
+ * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
+ * to be turned high in order to be detected by the USB Controller
+ * This signal should be handled by a USB specific power sequence
+ * in order to reset the Hub when USB bus is powered down.
+ */
+ usb-hub {
+ gpio-hog;
+ gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-hub-reset";
+ };
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb2_phy0 {
+ phy-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy1 {
+ phy-supply = <&vcc_5v>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
new file mode 100644
index 000000000000..0359539ba884
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12a.dtsi"
+
+/ {
+ compatible = "amlogic,g12b";
+
+ cpus {
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&cpu100>;
+ };
+
+ core1 {
+ cpu = <&cpu101>;
+ };
+
+ core2 {
+ cpu = <&cpu102>;
+ };
+
+ core3 {
+ cpu = <&cpu103>;
+ };
+ };
+ };
+
+ /delete-node/ cpu@2;
+ /delete-node/ cpu@3;
+
+ cpu100: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu101: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu102: cpu@102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x102>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu103: cpu@103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x103>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+ };
+};
+
+&clkc {
+ compatible = "amlogic,g12b-clkc";
+};
--
2.21.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH 0/6] arm64: Add initial support for Odroid-N2
2019-04-04 15:05 ` Neil Armstrong
(?)
@ 2019-04-16 18:37 ` Kevin Hilman
-1 siblings, 0 replies; 24+ messages in thread
From: Kevin Hilman @ 2019-04-16 18:37 UTC (permalink / raw)
To: Neil Armstrong, jbrunet
Cc: baylibre-upstreaming, Neil Armstrong, linux-amlogic,
linux-arm-kernel, linux-kernel
Neil Armstrong <narmstrong@baylibre.com> writes:
> This patchset adds basic support for :
> - Amlogic G12B, which is very similar to G12A
> - The HardKernel Odroid-N2 based on the S922X SoC
>
> The Amlogic G12B SoC is very similar with the G12A SoC, sharing
> most of the features and architecture, but with these differences :
> - The first CPU cluster only has 2xCortex-A53 instead of 4
> - G12B has a second cluster of 4xCortex-A73
> - Both cluster can achieve 2GHz instead of 1,8GHz for G12A
> - CPU Clock architecture is difference, thus needing a different
> compatible to handle this slight difference
> - Supports a MIPI CSI input
> - Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
>
> Actual support is done in the same way as for the GXM support, including
> the G12A dtsi and redefining the CPU clusters.
> Unlike GXM, the first cluster is different, thus needing to remove
> the last 2 cpu nodes of the first cluster.
>
> G12B clock driver is very close, the main differences are :
> - the clock tree is duplicated for the both clusters, and the
> SYS_PLL are swapped between the clusters
> - G12A has additional clocks like for CSI an other components
>
> Dependencies :
> - Patch 1, 3, 4, 5 : None
> - Patch 2 : Depends on the v5.2 meson-clk PULL request
> - Patch 6 depends on the G12A Display DT patchset at [2]
These deps are merged/queued.
I'm assuming you'll take patches 1-3 via clk-meson. After you have a
stable tag there, i can take the 4-6 via my tree.
Kevin
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 0/6] arm64: Add initial support for Odroid-N2
@ 2019-04-16 18:37 ` Kevin Hilman
0 siblings, 0 replies; 24+ messages in thread
From: Kevin Hilman @ 2019-04-16 18:37 UTC (permalink / raw)
To: Neil Armstrong, jbrunet
Cc: baylibre-upstreaming, linux-amlogic, linux-kernel,
linux-arm-kernel, Neil Armstrong
Neil Armstrong <narmstrong@baylibre.com> writes:
> This patchset adds basic support for :
> - Amlogic G12B, which is very similar to G12A
> - The HardKernel Odroid-N2 based on the S922X SoC
>
> The Amlogic G12B SoC is very similar with the G12A SoC, sharing
> most of the features and architecture, but with these differences :
> - The first CPU cluster only has 2xCortex-A53 instead of 4
> - G12B has a second cluster of 4xCortex-A73
> - Both cluster can achieve 2GHz instead of 1,8GHz for G12A
> - CPU Clock architecture is difference, thus needing a different
> compatible to handle this slight difference
> - Supports a MIPI CSI input
> - Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
>
> Actual support is done in the same way as for the GXM support, including
> the G12A dtsi and redefining the CPU clusters.
> Unlike GXM, the first cluster is different, thus needing to remove
> the last 2 cpu nodes of the first cluster.
>
> G12B clock driver is very close, the main differences are :
> - the clock tree is duplicated for the both clusters, and the
> SYS_PLL are swapped between the clusters
> - G12A has additional clocks like for CSI an other components
>
> Dependencies :
> - Patch 1, 3, 4, 5 : None
> - Patch 2 : Depends on the v5.2 meson-clk PULL request
> - Patch 6 depends on the G12A Display DT patchset at [2]
These deps are merged/queued.
I'm assuming you'll take patches 1-3 via clk-meson. After you have a
stable tag there, i can take the 4-6 via my tree.
Kevin
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 0/6] arm64: Add initial support for Odroid-N2
@ 2019-04-16 18:37 ` Kevin Hilman
0 siblings, 0 replies; 24+ messages in thread
From: Kevin Hilman @ 2019-04-16 18:37 UTC (permalink / raw)
To: Neil Armstrong, jbrunet
Cc: baylibre-upstreaming, linux-amlogic, linux-kernel,
linux-arm-kernel, Neil Armstrong
Neil Armstrong <narmstrong@baylibre.com> writes:
> This patchset adds basic support for :
> - Amlogic G12B, which is very similar to G12A
> - The HardKernel Odroid-N2 based on the S922X SoC
>
> The Amlogic G12B SoC is very similar with the G12A SoC, sharing
> most of the features and architecture, but with these differences :
> - The first CPU cluster only has 2xCortex-A53 instead of 4
> - G12B has a second cluster of 4xCortex-A73
> - Both cluster can achieve 2GHz instead of 1,8GHz for G12A
> - CPU Clock architecture is difference, thus needing a different
> compatible to handle this slight difference
> - Supports a MIPI CSI input
> - Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
>
> Actual support is done in the same way as for the GXM support, including
> the G12A dtsi and redefining the CPU clusters.
> Unlike GXM, the first cluster is different, thus needing to remove
> the last 2 cpu nodes of the first cluster.
>
> G12B clock driver is very close, the main differences are :
> - the clock tree is duplicated for the both clusters, and the
> SYS_PLL are swapped between the clusters
> - G12A has additional clocks like for CSI an other components
>
> Dependencies :
> - Patch 1, 3, 4, 5 : None
> - Patch 2 : Depends on the v5.2 meson-clk PULL request
> - Patch 6 depends on the G12A Display DT patchset at [2]
These deps are merged/queued.
I'm assuming you'll take patches 1-3 via clk-meson. After you have a
stable tag there, i can take the 4-6 via my tree.
Kevin
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 24+ messages in thread
end of thread, other threads:[~2019-04-16 18:38 UTC | newest]
Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-04-04 15:05 [PATCH 0/6] arm64: Add initial support for Odroid-N2 Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` [PATCH 1/6] dt-bindings: clk: meson: add g12b periph clock controller bindings Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` [PATCH 2/6] clk: meson: g12a: Add support for G12B CPUB clocks Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` [PATCH 3/6] clk: meson: g12a: mark fclk_div3 as critical Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` [PATCH 4/6] dt-bindings: arm: amlogic: add G12B bindings Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` [PATCH 5/6] dt-bindings: arm: amlogic: add Odroid-N2 binding Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` [PATCH 6/6] arm64: dts: meson: Add minimal support for Odroid-N2 Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-04 15:05 ` Neil Armstrong
2019-04-16 18:37 ` [PATCH 0/6] arm64: Add initial " Kevin Hilman
2019-04-16 18:37 ` Kevin Hilman
2019-04-16 18:37 ` Kevin Hilman
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.