[U-Boot] [PATCH] imx: Add variscite DART-6UL Evaluation Kit

* [U-Boot] [PATCH] imx: Add variscite DART-6UL Evaluation Kit
@ 2019-04-17 22:04 Parthiban Nallathambi
  2019-04-26  9:38 ` [U-Boot] " sbabic at denx.de
  0 siblings, 1 reply; 4+ messages in thread
From: Parthiban Nallathambi @ 2019-04-17 22:04 UTC (permalink / raw)
  To: u-boot

Port for the DART-6UL Evaluation Kit SBC. Based on the variscite
DART-6UL iMX6ULL SoM.

CPU:   Freescale i.MX6ULL rev1.1 900 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 43C
Reset cause: POR
Model: Variscite DART-6UL Evaluation Kit
Board: Variscite DART-6UL Evaluation Kit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial at 02020000
Out:   serial at 02020000
Err:   serial at 02020000
Net:   FEC0

Working:
 - Eth0
 - i2c
 - MMC/SD
 - eMMC
 - USB host
 - UART 1

Note: LCDIF porting needs DM_VIDEO
https://lists.denx.de/pipermail/u-boot/2019-April/365506.html

Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
---
 arch/arm/Kconfig                     |   1 +
 arch/arm/dts/Makefile                |   1 +
 arch/arm/dts/imx6ull-dart-6ul.dts    |  39 ++++
 arch/arm/dts/imx6ull-dart-6ul.dtsi   | 261 +++++++++++++++++++++++++++
 arch/arm/mach-imx/mx6/Kconfig        |  12 ++
 board/variscite/dart_6ul/Kconfig     |  12 ++
 board/variscite/dart_6ul/MAINTAINERS |   8 +
 board/variscite/dart_6ul/Makefile    |   4 +
 board/variscite/dart_6ul/README      |  41 +++++
 board/variscite/dart_6ul/dart_6ul.c  | 228 +++++++++++++++++++++++
 board/variscite/dart_6ul/spl.c       | 215 ++++++++++++++++++++++
 configs/variscite_dart6ul_defconfig  |  55 ++++++
 include/configs/dart_6ul.h           | 131 ++++++++++++++
 13 files changed, 1008 insertions(+)
 create mode 100644 arch/arm/dts/imx6ull-dart-6ul.dts
 create mode 100644 arch/arm/dts/imx6ull-dart-6ul.dtsi
 create mode 100644 board/variscite/dart_6ul/Kconfig
 create mode 100644 board/variscite/dart_6ul/MAINTAINERS
 create mode 100644 board/variscite/dart_6ul/Makefile
 create mode 100644 board/variscite/dart_6ul/README
 create mode 100644 board/variscite/dart_6ul/dart_6ul.c
 create mode 100644 board/variscite/dart_6ul/spl.c
 create mode 100644 configs/variscite_dart6ul_defconfig
 create mode 100644 include/configs/dart_6ul.h

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 4640f3b3bd..c20866c86a 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1635,6 +1635,7 @@ source "board/tcl/sl50/Kconfig"
 source "board/ucRobotics/bubblegum_96/Kconfig"
 source "board/birdland/bav335x/Kconfig"
 source "board/toradex/colibri_pxa270/Kconfig"
+source "board/variscite/dart_6ul/Kconfig"
 source "board/vscom/baltos/Kconfig"
 source "board/woodburn/Kconfig"
 source "board/xilinx/Kconfig"
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 0aee8dfde0..6fb545dc9f 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -549,6 +549,7 @@ dtb-$(CONFIG_MX6UL) += \
 dtb-$(CONFIG_MX6ULL) += \
 	imx6ull-14x14-evk.dtb \
 	imx6ull-colibri.dtb \
+	imx6ull-dart-6ul.dtb
 
 dtb-$(CONFIG_ARCH_MX6) += \
 	imx6-colibri.dtb
diff --git a/arch/arm/dts/imx6ull-dart-6ul.dts b/arch/arm/dts/imx6ull-dart-6ul.dts
new file mode 100644
index 0000000000..4cab1a048b
--- /dev/null
+++ b/arch/arm/dts/imx6ull-dart-6ul.dts
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull.dtsi"
+#include "imx6ull-dart-6ul.dtsi"
+
+/ {
+	model = "Variscite DART-6UL Evaluation Kit";
+	compatible = "variscite,imx6ull-dart-6ul", "fsl,imx6ull";
+};
+
+&usdhc2 {
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID    0x17059
+		>;
+	};
+
+};
diff --git a/arch/arm/dts/imx6ull-dart-6ul.dtsi b/arch/arm/dts/imx6ull-dart-6ul.dtsi
new file mode 100644
index 0000000000..e96669f493
--- /dev/null
+++ b/arch/arm/dts/imx6ull-dart-6ul.dtsi
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+
+/ {
+	model = "Variscite DART-6UL i.MX6 Ultra Low Lite SOM";
+	compatible = "variscite,imx6ull-dart-6ul", "fsl,imx6ull";
+
+	memory {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio1: mdio1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy at 1 {
+			reg = <1>;
+			micrel,led-mode = <1>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio2: mdio2 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy at 2 {
+			reg = <2>;
+			micrel,led-mode = <1>;
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	fsl,no-blockmark-swap;
+	status = "disabled";
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	partition at 0 {
+		label = "uboot";
+		reg = <0x0 0x400000>;
+	};
+
+	partition at 400000 {
+		label = "uboot-env";
+		reg = <0x400000 0x100000>;
+	};
+
+	partition at 500000 {
+		label = "root";
+		reg = <0x500000 0x0>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	eeprom at 50 {
+		compatible = "cat,24c32";
+		reg = <0x50>;
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	#pwm-cells = <3>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	bus-width = <0x4>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	keep-power-in-suspend;
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0X1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0X1b0b0
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__RAWNAND_DQS		0x0b0b1
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0x0b0b1
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0x0b0b1
+			MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B	0x0b0b1
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0x0b000
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0x0b0b1
+			MX6UL_PAD_NAND_CE1_B__RAWNAND_CE1_B	0x0b0b1
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0x0b0b1
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0x0b0b1
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x0b0b1
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x0b0b1
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0x0b0b1
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0x0b0b1
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0x0b0b1
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0x0b0b1
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0x0b0b1
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0x0b0b1
+		>;
+	};
+
+	pinctrl_i2c1: i2cgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL       0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA       0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1grp_gpio {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
+		>;
+	};
+
+	pinctrl_i2c2: i2cgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL       0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA       0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2grp_gpio {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x1b8b0
+			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31	0x1b8b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__GPIO3_IO05	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
+
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170f9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170f9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170f9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170f9
+		>;
+	};
+};
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index e782859b1e..f513c4c06f 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -161,6 +161,18 @@ config TARGET_COLIBRI_IMX6ULL
 	select DM_THERMAL
 	select MX6ULL
 
+config TARGET_DART_6UL
+	bool "Variscite imx6ULL dart(DART-SOM-6ULL)"
+	select MX6ULL
+	select DM
+	select DM_ETH
+	select DM_GPIO
+	select DM_I2C
+	select DM_MMC
+	select DM_SERIAL
+	select DM_THERMAL
+	select SUPPORT_SPL
+
 config TARGET_DHCOMIMX6
 	bool "dh_imx6"
 	select BOARD_EARLY_INIT_F
diff --git a/board/variscite/dart_6ul/Kconfig b/board/variscite/dart_6ul/Kconfig
new file mode 100644
index 0000000000..1765af1d82
--- /dev/null
+++ b/board/variscite/dart_6ul/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_DART_6UL
+
+config SYS_BOARD
+	default "dart_6ul"
+
+config SYS_VENDOR
+	default "variscite"
+
+config SYS_CONFIG_NAME
+	default "dart_6ul"
+
+endif
diff --git a/board/variscite/dart_6ul/MAINTAINERS b/board/variscite/dart_6ul/MAINTAINERS
new file mode 100644
index 0000000000..339f93fa66
--- /dev/null
+++ b/board/variscite/dart_6ul/MAINTAINERS
@@ -0,0 +1,8 @@
+MX6UL_DART BOARD
+M:	Parthiban Nallathambi <parthitce@gmail.com>
+S:	Maintained
+F:	arch/arm/dts/imx6ull-dart-6ul.dts
+F:	arch/arm/dts/imx6ull-dart-6ul.dtsi
+F:	board/variscite/dart_6ul/
+F:	configs/variscite_dart6ul_defconfig
+F:	include/configs/dart_6ul.h
diff --git a/board/variscite/dart_6ul/Makefile b/board/variscite/dart_6ul/Makefile
new file mode 100644
index 0000000000..48aa361bf2
--- /dev/null
+++ b/board/variscite/dart_6ul/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier:	GPL-2.0+
+
+obj-y  := dart_6ul.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
diff --git a/board/variscite/dart_6ul/README b/board/variscite/dart_6ul/README
new file mode 100644
index 0000000000..d76b997e22
--- /dev/null
+++ b/board/variscite/dart_6ul/README
@@ -0,0 +1,41 @@
+How to use U-Boot on variscite DART-6UL Evaluation Kit
+------------------------------------------------------
+
+- Configure and build U-Boot for DART-6UL iMX6ULL:
+
+    $ make mrproper
+    $ make variscite_dart6ul_defconfig
+    $ make
+
+  This will generate SPL and u-boot-dtb.img images.
+
+Boot from MMC/SD:
+- The SPL and u-boot-dtb.img images need to be flashed into the micro SD card:
+
+    $ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+    $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Boot mode settings:
+
+  Boot switch position: SW1 -> 0
+			SW2 -> 0
+
+Boot from eMMC:
+- if bootpart is not enabled by default, to enable under Linux
+	echo 0 >/sys/block/mmcblk1boot0/force_ro
+	mmc bootpart enable 1 1 /dev/mmcblk1boot0
+
+- Flash the SPL and u-boot-dtb.img to mmcblk1boot0
+    $ sudo dd if=SPL of=/dev/mmcblk1boot0 bs=1k seek=1; sync
+    $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk1boot0 bs=1k seek=69; sync
+
+- Boot mode settings:
+
+  Boot switch position: SW1 -> 0
+			SW2 -> 1
+
+- Connect the Serial cable to UART0 and the PC for the console.
+
+- Insert the micro SD card in the board and power it up.
+
+- U-Boot messages should come up.
diff --git a/board/variscite/dart_6ul/dart_6ul.c b/board/variscite/dart_6ul/dart_6ul.c
new file mode 100644
index 0000000000..4765595af1
--- /dev/null
+++ b/board/variscite/dart_6ul/dart_6ul.c
@@ -0,0 +1,228 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015-2019 Variscite Ltd.
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc.h>
+#include <linux/bitops.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
+
+#ifdef CONFIG_NAND_MXS
+#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
+#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
+			PAD_CTL_SRE_FAST)
+#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
+static iomux_v3_cfg_t const nand_pads[] = {
+	MX6_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA02__RAWNAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA03__RAWNAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA04__RAWNAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA05__RAWNAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA06__RAWNAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA07__RAWNAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_CLE__RAWNAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_ALE__RAWNAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_RE_B__RAWNAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_WE_B__RAWNAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_READY_B__RAWNAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DQS__RAWNAND_DQS | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+};
+
+static void setup_gpmi_nand(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	/* config gpmi nand iomux */
+	imx_iomux_v3_setup_multiple_pads(nand_pads, ARRAY_SIZE(nand_pads));
+
+	clrbits_le32(&mxc_ccm->CCGR4,
+		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+
+	/*
+	 * config gpmi and bch clock to 100 MHz
+	 * bch/gpmi select PLL2 PFD2 400M
+	 * 100M = 400M / 4
+	 */
+	clrbits_le32(&mxc_ccm->cscmr1,
+		     MXC_CCM_CSCMR1_BCH_CLK_SEL |
+		     MXC_CCM_CSCMR1_GPMI_CLK_SEL);
+	clrsetbits_le32(&mxc_ccm->cscdr1,
+			MXC_CCM_CSCDR1_BCH_PODF_MASK |
+			MXC_CCM_CSCDR1_GPMI_PODF_MASK,
+			(3 << MXC_CCM_CSCDR1_BCH_PODF_OFFSET) |
+			(3 << MXC_CCM_CSCDR1_GPMI_PODF_OFFSET));
+
+	/* enable gpmi and bch clock gating */
+	setbits_le32(&mxc_ccm->CCGR4,
+		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+
+	/* enable apbh clock gating */
+	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
+#define ENET_PAD_CTRL     (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE       | \
+			   PAD_CTL_SPEED_HIGH  | PAD_CTL_DSE_48ohm | \
+			   PAD_CTL_SRE_FAST)
+#define MDIO_PAD_CTRL     (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE      | \
+			   PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST | \
+			   PAD_CTL_ODE)
+/*
+ * pin conflicts for fec1 and fec2, GPIO1_IO06 and GPIO1_IO07 can only
+ * be used for ENET1 or ENET2, cannot be used for both.
+ */
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const fec2_pads[] = {
+	MX6_PAD_GPIO1_IO06__ENET2_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO07__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_EN__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_ER__ENET2_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_EN__ENET2_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_fec(int fec_id)
+{
+	if (fec_id == 0)
+		imx_iomux_v3_setup_multiple_pads(fec1_pads,
+						 ARRAY_SIZE(fec1_pads));
+	else
+		imx_iomux_v3_setup_multiple_pads(fec2_pads,
+						 ARRAY_SIZE(fec2_pads));
+}
+
+int board_eth_init(bd_t *bis)
+{
+	int ret = 0;
+
+	ret = fecmxc_initialize_multi(bis, CONFIG_FEC_ENET_DEV,
+				      CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+
+#if defined(CONFIG_CI_UDC) && defined(CONFIG_USB_ETHER)
+	/* USB Ethernet Gadget */
+	usb_eth_initialize(bis);
+#endif
+	return ret;
+}
+
+static int setup_fec(int fec_id)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	if (fec_id == 0) {
+		/*
+		 * Use 50M anatop loopback REF_CLK1 for ENET1,
+		 * clear gpr1[13], set gpr1[17].
+		 */
+		clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+				IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+	} else {
+		/*
+		 * Use 50M anatop loopback REF_CLK2 for ENET2,
+		 * clear gpr1[14], set gpr1[18].
+		 */
+		clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
+				IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+	}
+
+	ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	enable_enet_clk(1);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/*
+	 * Defaults + Enable status LEDs (LED1: Activity, LED0: Link) & select
+	 * 50 MHz RMII clock mode.
+	 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif /* CONFIG_FEC_MXC */
+
+int board_early_init_f(void)
+{
+	setup_iomux_fec(CONFIG_FEC_ENET_DEV);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec(CONFIG_FEC_ENET_DEV);
+#endif
+
+#ifdef CONFIG_NAND_MXS
+	setup_gpmi_nand();
+#endif
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: Variscite DART-6UL Evaluation Kit\n");
+
+	return 0;
+}
diff --git a/board/variscite/dart_6ul/spl.c b/board/variscite/dart_6ul/spl.c
new file mode 100644
index 0000000000..f7e6ab6325
--- /dev/null
+++ b/board/variscite/dart_6ul/spl.c
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015-2019 Variscite Ltd.
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/arch/clock.h>
+#include <asm/io.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/crm_regs.h>
+#include <fsl_esdhc.h>
+
+#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_addds = 0x00000030,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_b0ds = 0x00000030,
+	.grp_ctlds = 0x00000030,
+	.grp_b1ds = 0x00000030,
+	.grp_ddrpke = 0x00000000,
+	.grp_ddrmode = 0x00020000,
+	.grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_dqm0 = 0x00000030,
+	.dram_dqm1 = 0x00000030,
+	.dram_ras = 0x00000030,
+	.dram_cas = 0x00000030,
+	.dram_odt0 = 0x00000030,
+	.dram_odt1 = 0x00000030,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdclk_0 = 0x00000008,
+	.dram_sdqs0 = 0x00000038,
+	.dram_sdqs1 = 0x00000030,
+	.dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 = 0x00000000,
+	.p0_mpdgctrl0   = 0x414C0158,
+	.p0_mprddlctl   = 0x40403A3A,
+	.p0_mpwrdlctl   = 0x40405A56,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+	.dsize = 0,
+	.cs_density = 20,
+	.ncs = 1,
+	.cs1_mirror = 0,
+	.rtt_wr = 2,
+	.rtt_nom = 1,		/* RTT_Nom = RZQ/2 */
+	.walat = 1,		/* Write additional latency */
+	.ralat = 5,		/* Read additional latency */
+	.mif3_mode = 3,		/* Command prediction working mode */
+	.bi_on = 1,		/* Bank interleaving enabled */
+	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 800,
+	.density = 4,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 15,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0xFFFFFFFF, &ccm->CCGR0);
+	writel(0xFFFFFFFF, &ccm->CCGR1);
+	writel(0xFFFFFFFF, &ccm->CCGR2);
+	writel(0xFFFFFFFF, &ccm->CCGR3);
+	writel(0xFFFFFFFF, &ccm->CCGR4);
+	writel(0xFFFFFFFF, &ccm->CCGR5);
+	writel(0xFFFFFFFF, &ccm->CCGR6);
+	writel(0xFFFFFFFF, &ccm->CCGR7);
+	/* Enable Audio Clock for SOM codec */
+	writel(0x01130100, (long *)CCM_CCOSR);
+}
+
+static void spl_dram_init(void)
+{
+	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifndef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+#endif
+
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{
+		.esdhc_base = USDHC1_BASE_ADDR,
+		.max_bus_width = 4,
+	},
+#ifndef CONFIG_NAND_MXS
+	{
+		.esdhc_base = USDHC2_BASE_ADDR,
+		.max_bus_width = 8,
+	},
+#endif
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			SETUP_IOMUX_PADS(usdhc1_pads);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+#ifndef CONFIG_NAND_MXS
+		case 1:
+			SETUP_IOMUX_PADS(usdhc2_pads);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+#endif
+		default:
+			printf("Warning - USDHC%d controller not supporting\n",
+			       i + 1);
+			return 0;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret) {
+			printf("Warning: failed to initialize mmc dev %d\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+void board_init_f(ulong dummy)
+{
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+
+	/* setup GP timer */
+	timer_init();
+
+	setup_iomux_uart();
+
+	/* iomux and setup of i2c */
+	board_early_init_f();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
diff --git a/configs/variscite_dart6ul_defconfig b/configs/variscite_dart6ul_defconfig
new file mode 100644
index 0000000000..a1cdd05619
--- /dev/null
+++ b/configs/variscite_dart6ul_defconfig
@@ -0,0 +1,55 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x86000000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_TARGET_DART_6UL=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL=y
+# CONFIG_CMD_DEKBLOB is not set
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_NR_DRAM_BANKS=8
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
+# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_USB_HOST_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+# CONFIG_RANDOM_UUID is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_NET=y
+# CONFIG_ISO_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6ull-dart-6ul"
+CONFIG_DM_I2C_GPIO=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_MXC_UART=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Variscite"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_LZO=y
diff --git a/include/configs/dart_6ul.h b/include/configs/dart_6ul.h
new file mode 100644
index 0000000000..fb1b899d71
--- /dev/null
+++ b/include/configs/dart_6ul.h
@@ -0,0 +1,131 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Board configuration file for Variscite DART-6UL Evaluation Kit
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+#ifndef __DART_6UL_H
+#define __DART_6UL_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* SPL options */
+#include "imx6_spl.h"
+
+/* NAND pin conflicts with usdhc2 */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_SYS_FSL_USDHC_NUM        1
+#else
+#define CONFIG_SYS_FSL_USDHC_NUM        2
+#endif
+
+#ifdef CONFIG_CMD_NET
+#define CONFIG_FEC_ENET_DEV		0
+
+#if (CONFIG_FEC_ENET_DEV == 0)
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR		0x1
+#define CONFIG_FEC_XCV_TYPE		RMII
+#define CONFIG_ETHPRIME			"eth0"
+#elif (CONFIG_FEC_ENET_DEV == 1)
+#define IMX_FEC_BASE			ENET2_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR		0x3
+#define CONFIG_FEC_XCV_TYPE		RMII
+#define CONFIG_ETHPRIME			"eth1"
+#endif
+#endif
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
+
+/* Environment settings */
+#define CONFIG_ENV_SIZE			SZ_8K
+#define CONFIG_ENV_OFFSET		(14 * SZ_64K)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_OFFSET_REDUND	\
+	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* Environment in SD */
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_SYS_MMC_ENV_PART		0
+#define MMC_ROOTFS_DEV			0
+#define MMC_ROOTFS_PART			2
+
+/* Console configs */
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_FSL_USDHC
+
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC2_BASE_ADDR
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+/* I2C configs */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_SPEED		100000
+#endif
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x8000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+/* Physical Memory Map */
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE			SZ_512M
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
+
+#define CONFIG_IMX_THERMAL
+
+#define ENV_MMC \
+	"mmcdev=" __stringify(MMC_ROOTFS_DEV) "\0" \
+	"mmcpart=" __stringify(MMC_ROOTFS_PART) "\0" \
+	"fitpart=1\0" \
+	"bootdelay=3\0" \
+	"silent=1\0" \
+	"optargs=rw rootwait\0" \
+	"mmcautodetect=yes\0" \
+	"mmcrootfstype=ext4\0" \
+	"mmcfit_name=fitImage\0" \
+	"mmcloadfit=fatload mmc ${mmcdev}:${fitpart} ${fit_addr} " \
+		    "${mmcfit_name}\0" \
+	"mmcargs=setenv bootargs " \
+		"root=/dev/mmcblk${mmcdev}p${mmcpart} ${optargs} " \
+		"console=${console} rootfstype=${mmcrootfstype}\0" \
+	"mmc_mmc_fit=run mmcloadfit;run mmcargs addcon; bootm ${fit_addr}\0" \
+
+/* Default environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"fdt_high=0xffffffff\0" \
+	"console=ttymxc0,115200n8\0" \
+	"addcon=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \
+	"fit_addr=0x82000000\0" \
+	ENV_MMC
+
+#define CONFIG_BOOTCOMMAND		"run mmc_mmc_fit"
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 0) \
+	func(MMC, mmc, 1) \
+	func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+#endif /* __DART_6UL_H */
-- 
2.17.2

^ permalink raw reply related	[flat|nested] 4+ messages in thread