All of lore.kernel.org
 help / color / mirror / Atom feed
From: Jagan Teki <jagan@amarulasolutions.com>
To: Maxime Ripard <maxime.ripard@bootlin.com>,
	Chen-Yu Tsai <wens@csie.org>, Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-amarula@amarulasolutions.com,
	Jagan Teki <jagan@amarulasolutions.com>
Subject: [PATCH 2/2] arm64: dts: allwinner: a64-amarula-relic: Add OV5640 camera node
Date: Thu, 18 Apr 2019 14:08:13 +0530	[thread overview]
Message-ID: <20190418083813.11776-2-jagan@amarulasolutions.com> (raw)
In-Reply-To: <20190418083813.11776-1-jagan@amarulasolutions.com>

Amarula A64-Relic board by default bound with OV5640 camera,
so add support for it with below pin information.

- PE13, PE12 via i2c-gpio bitbanging
- CLK_CSI_MCLK as external clock
- PE1 as external clock pin muxing
- ALDO1 as AVDD supply
- DLDO3 as DOVDD supply
- ELDO3 as DVDD supply
- PE14 gpio for reset pin
- PE15 gpio for powerdown pin

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---

 .../allwinner/sun50i-a64-amarula-relic.dts    | 53 +++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
index 3819ce396073..56c76b712e3b 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
@@ -22,6 +22,41 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	i2c-csi {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* CSI-SDA: PE13 */
+		scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* CSI-SCK: PE12 */
+		i2c-gpio,delay-us = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ov5640: camera@3c {
+			compatible = "ovti,ov5640";
+			reg = <0x3c>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&csi_mclk_pin>;
+			clocks = <&ccu CLK_CSI_MCLK>;
+			clock-names = "xclk";
+
+			AVDD-supply = <&reg_aldo1>;
+			DOVDD-supply = <&reg_dldo3>;
+			DVDD-supply = <&reg_eldo3>;
+			reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* CSI-RST-R: PE14 */
+			powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* CSI-STBY-R: PE15 */
+
+			port {
+				ov5640_ep: endpoint {
+					remote-endpoint = <&csi_ep>;
+					bus-width = <8>;
+					hsync-active = <1>; /* Active high */
+					vsync-active = <0>; /* Active low */
+					data-active = <1>;  /* Active high */
+					pclk-sample = <1>;  /* Rising */
+				};
+			};
+		};
+	};
+
 	wifi_pwrseq: wifi-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		clocks = <&rtc 1>;
@@ -30,6 +65,24 @@
 	};
 };
 
+&csi {
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi_ep: endpoint {
+			remote-endpoint = <&ov5640_ep>;
+			bus-width = <8>;
+			hsync-active = <1>; /* Active high */
+			vsync-active = <0>; /* Active low */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
 &ehci0 {
 	status = "okay";
 };
-- 
2.18.0.321.gffc6fa0e3


WARNING: multiple messages have this Message-ID (diff)
From: Jagan Teki <jagan@amarulasolutions.com>
To: Maxime Ripard <maxime.ripard@bootlin.com>,
	Chen-Yu Tsai <wens@csie.org>, Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	Jagan Teki <jagan@amarulasolutions.com>,
	Michael Trimarchi <michael@amarulasolutions.com>,
	linux-amarula@amarulasolutions.com,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/2] arm64: dts: allwinner: a64-amarula-relic: Add OV5640 camera node
Date: Thu, 18 Apr 2019 14:08:13 +0530	[thread overview]
Message-ID: <20190418083813.11776-2-jagan@amarulasolutions.com> (raw)
In-Reply-To: <20190418083813.11776-1-jagan@amarulasolutions.com>

Amarula A64-Relic board by default bound with OV5640 camera,
so add support for it with below pin information.

- PE13, PE12 via i2c-gpio bitbanging
- CLK_CSI_MCLK as external clock
- PE1 as external clock pin muxing
- ALDO1 as AVDD supply
- DLDO3 as DOVDD supply
- ELDO3 as DVDD supply
- PE14 gpio for reset pin
- PE15 gpio for powerdown pin

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---

 .../allwinner/sun50i-a64-amarula-relic.dts    | 53 +++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
index 3819ce396073..56c76b712e3b 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
@@ -22,6 +22,41 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	i2c-csi {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* CSI-SDA: PE13 */
+		scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* CSI-SCK: PE12 */
+		i2c-gpio,delay-us = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ov5640: camera@3c {
+			compatible = "ovti,ov5640";
+			reg = <0x3c>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&csi_mclk_pin>;
+			clocks = <&ccu CLK_CSI_MCLK>;
+			clock-names = "xclk";
+
+			AVDD-supply = <&reg_aldo1>;
+			DOVDD-supply = <&reg_dldo3>;
+			DVDD-supply = <&reg_eldo3>;
+			reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* CSI-RST-R: PE14 */
+			powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* CSI-STBY-R: PE15 */
+
+			port {
+				ov5640_ep: endpoint {
+					remote-endpoint = <&csi_ep>;
+					bus-width = <8>;
+					hsync-active = <1>; /* Active high */
+					vsync-active = <0>; /* Active low */
+					data-active = <1>;  /* Active high */
+					pclk-sample = <1>;  /* Rising */
+				};
+			};
+		};
+	};
+
 	wifi_pwrseq: wifi-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		clocks = <&rtc 1>;
@@ -30,6 +65,24 @@
 	};
 };
 
+&csi {
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi_ep: endpoint {
+			remote-endpoint = <&ov5640_ep>;
+			bus-width = <8>;
+			hsync-active = <1>; /* Active high */
+			vsync-active = <0>; /* Active low */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
 &ehci0 {
 	status = "okay";
 };
-- 
2.18.0.321.gffc6fa0e3


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply	other threads:[~2019-04-18  8:38 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-04-18  8:38 [PATCH 1/2] arm64: dts: allwinner: a64: Add pinmux setting for CSI MCLK on PE1 Jagan Teki
2019-04-18  8:38 ` Jagan Teki
2019-04-18  8:38 ` Jagan Teki [this message]
2019-04-18  8:38   ` [PATCH 2/2] arm64: dts: allwinner: a64-amarula-relic: Add OV5640 camera node Jagan Teki
2019-04-18 11:20   ` Maxime Ripard
2019-04-18 11:20     ` Maxime Ripard
2019-04-18 11:20 ` [PATCH 1/2] arm64: dts: allwinner: a64: Add pinmux setting for CSI MCLK on PE1 Maxime Ripard
2019-04-18 11:20   ` Maxime Ripard

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190418083813.11776-2-jagan@amarulasolutions.com \
    --to=jagan@amarulasolutions.com \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-amarula@amarulasolutions.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=maxime.ripard@bootlin.com \
    --cc=michael@amarulasolutions.com \
    --cc=robh+dt@kernel.org \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.