* [PATCH v3 0/2] Qualcomm PCIe2 PHY
@ 2019-05-02 0:14 ` Bjorn Andersson
0 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2019-05-02 0:14 UTC (permalink / raw)
Cc: Kishon Vijay Abraham I, Rob Herring, Mark Rutland, linux-arm-msm,
linux-kernel, devicetree
The Qualcomm PCIe2 PHY is based on design from Synopsys and found in
several different platforms where the QMP PHY isn't used.
Bjorn Andersson (2):
dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
phy: qcom: Add Qualcomm PCIe2 PHY driver
.../bindings/phy/qcom-pcie2-phy.txt | 42 +++
drivers/phy/qualcomm/Kconfig | 8 +
drivers/phy/qualcomm/Makefile | 1 +
drivers/phy/qualcomm/phy-qcom-pcie2.c | 331 ++++++++++++++++++
4 files changed, 382 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt
create mode 100644 drivers/phy/qualcomm/phy-qcom-pcie2.c
--
2.18.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 0/2] Qualcomm PCIe2 PHY
@ 2019-05-02 0:14 ` Bjorn Andersson
0 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2019-05-02 0:14 UTC (permalink / raw)
Cc: Kishon Vijay Abraham I, Rob Herring, Mark Rutland, linux-arm-msm,
linux-kernel, devicetree
The Qualcomm PCIe2 PHY is based on design from Synopsys and found in
several different platforms where the QMP PHY isn't used.
Bjorn Andersson (2):
dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
phy: qcom: Add Qualcomm PCIe2 PHY driver
.../bindings/phy/qcom-pcie2-phy.txt | 42 +++
drivers/phy/qualcomm/Kconfig | 8 +
drivers/phy/qualcomm/Makefile | 1 +
drivers/phy/qualcomm/phy-qcom-pcie2.c | 331 ++++++++++++++++++
4 files changed, 382 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt
create mode 100644 drivers/phy/qualcomm/phy-qcom-pcie2.c
--
2.18.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 1/2] dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
2019-05-02 0:14 ` Bjorn Andersson
(?)
@ 2019-05-02 0:14 ` Bjorn Andersson
2019-05-02 21:36 ` Rob Herring
-1 siblings, 1 reply; 6+ messages in thread
From: Bjorn Andersson @ 2019-05-02 0:14 UTC (permalink / raw)
To: Kishon Vijay Abraham I, Rob Herring, Mark Rutland
Cc: linux-arm-msm, linux-kernel, devicetree
The Qualcomm PCIe2 PHY is a Synopsys based PCIe PHY found in a number of
Qualcomm platforms, add a binding to describe this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
Changes since v2:
- Add #clock-cells
.../bindings/phy/qcom-pcie2-phy.txt | 42 +++++++++++++++++++
1 file changed, 42 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt
new file mode 100644
index 000000000000..30064253f290
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt
@@ -0,0 +1,42 @@
+Qualcomm PCIe2 PHY controller
+=============================
+
+The Qualcomm PCIe2 PHY is a Synopsys based phy found in a number of Qualcomm
+platforms.
+
+Required properties:
+ - compatible: compatible list, should be:
+ "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy"
+
+ - reg: offset and length of the PHY register set.
+ - #phy-cells: must be 0.
+
+ - clocks: a clock-specifier pair for the "pipe" clock
+
+ - vdda-vp-supply: phandle to low voltage regulator
+ - vdda-vph-supply: phandle to high voltage regulator
+
+ - resets: reset-specifier pairs for the "phy" and "pipe" resets
+ - reset-names: list of resets, should contain:
+ "phy" and "pipe"
+
+ - clock-output-names: name of the outgoing clock signal from the PHY PLL
+ - #clock-cells: must be 0
+
+Example:
+ phy@7786000 {
+ compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
+ reg = <0x07786000 0xb8>;
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
+ <&gcc GCC_PCIE_0_PIPE_ARES>;
+ reset-names = "phy", "pipe";
+
+ vdda-vp-supply = <&vreg_l3_1p05>;
+ vdda-vph-supply = <&vreg_l5_1p8>;
+
+ clock-output-names = "pcie_0_pipe_clk";
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ };
--
2.18.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 2/2] phy: qcom: Add Qualcomm PCIe2 PHY driver
2019-05-02 0:14 ` Bjorn Andersson
(?)
(?)
@ 2019-05-02 0:14 ` Bjorn Andersson
-1 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2019-05-02 0:14 UTC (permalink / raw)
To: Kishon Vijay Abraham I, Rob Herring, Mark Rutland
Cc: linux-arm-msm, linux-kernel, devicetree
The Qualcomm PCIe2 PHY is based on design from Synopsys and found in
several different platforms where the QMP PHY isn't used.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
Changes since v2:
- None
drivers/phy/qualcomm/Kconfig | 8 +
drivers/phy/qualcomm/Makefile | 1 +
drivers/phy/qualcomm/phy-qcom-pcie2.c | 331 ++++++++++++++++++++++++++
3 files changed, 340 insertions(+)
create mode 100644 drivers/phy/qualcomm/phy-qcom-pcie2.c
diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index 32f7d34eb784..8688ce27d0a6 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -24,6 +24,14 @@ config PHY_QCOM_IPQ806X_SATA
depends on OF
select GENERIC_PHY
+config PHY_QCOM_PCIE2
+ tristate "Qualcomm PCIe Gen2 PHY Driver"
+ depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST)
+ select GENERIC_PHY
+ help
+ Enable this to support the Qualcomm PCIe PHY, used with the Synopsys
+ based PCIe controller.
+
config PHY_QCOM_QMP
tristate "Qualcomm QMP PHY Driver"
depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST)
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index c56efd3af205..283251d6a5d9 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -2,6 +2,7 @@
obj-$(CONFIG_PHY_ATH79_USB) += phy-ath79-usb.o
obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
+obj-$(CONFIG_PHY_QCOM_PCIE2) += phy-qcom-pcie2.o
obj-$(CONFIG_PHY_QCOM_QMP) += phy-qcom-qmp.o
obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
diff --git a/drivers/phy/qualcomm/phy-qcom-pcie2.c b/drivers/phy/qualcomm/phy-qcom-pcie2.c
new file mode 100644
index 000000000000..9dba3594e6d9
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-pcie2.c
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2014-2017, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Linaro Ltd.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/clk.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#include <dt-bindings/phy/phy.h>
+
+#define PCIE20_PARF_PHY_STTS 0x3c
+#define PCIE2_PHY_RESET_CTRL 0x44
+#define PCIE20_PARF_PHY_REFCLK_CTRL2 0xa0
+#define PCIE20_PARF_PHY_REFCLK_CTRL3 0xa4
+#define PCIE20_PARF_PCS_SWING_CTRL1 0x88
+#define PCIE20_PARF_PCS_SWING_CTRL2 0x8c
+#define PCIE20_PARF_PCS_DEEMPH1 0x74
+#define PCIE20_PARF_PCS_DEEMPH2 0x78
+#define PCIE20_PARF_PCS_DEEMPH3 0x7c
+#define PCIE20_PARF_CONFIGBITS 0x84
+#define PCIE20_PARF_PHY_CTRL3 0x94
+#define PCIE20_PARF_PCS_CTRL 0x80
+
+#define TX_AMP_VAL 120
+#define PHY_RX0_EQ_GEN1_VAL 0
+#define PHY_RX0_EQ_GEN2_VAL 4
+#define TX_DEEMPH_GEN1_VAL 24
+#define TX_DEEMPH_GEN2_3_5DB_VAL 26
+#define TX_DEEMPH_GEN2_6DB_VAL 36
+#define PHY_TX0_TERM_OFFST_VAL 0
+
+struct qcom_phy {
+ struct device *dev;
+ void __iomem *base;
+
+ struct regulator_bulk_data vregs[2];
+
+ struct reset_control *phy_reset;
+ struct reset_control *pipe_reset;
+ struct clk *pipe_clk;
+};
+
+static int qcom_pcie2_phy_init(struct phy *phy)
+{
+ struct qcom_phy *qphy = phy_get_drvdata(phy);
+ int ret;
+
+ ret = reset_control_deassert(qphy->phy_reset);
+ if (ret) {
+ dev_err(qphy->dev, "cannot deassert pipe reset\n");
+ return ret;
+ }
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
+ if (ret)
+ reset_control_assert(qphy->phy_reset);
+
+ return ret;
+}
+
+static int qcom_pcie2_phy_power_on(struct phy *phy)
+{
+ struct qcom_phy *qphy = phy_get_drvdata(phy);
+ int ret;
+ u32 val;
+
+ /* Program REF_CLK source */
+ val = readl(qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL2);
+ val &= ~BIT(1);
+ writel(val, qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL2);
+
+ usleep_range(1000, 2000);
+
+ /* Don't use PAD for refclock */
+ val = readl(qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL2);
+ val &= ~BIT(0);
+ writel(val, qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL2);
+
+ /* Program SSP ENABLE */
+ val = readl(qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL3);
+ val |= BIT(0);
+ writel(val, qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL3);
+
+ usleep_range(1000, 2000);
+
+ /* Assert Phy SW Reset */
+ val = readl(qphy->base + PCIE2_PHY_RESET_CTRL);
+ val |= BIT(0);
+ writel(val, qphy->base + PCIE2_PHY_RESET_CTRL);
+
+ /* Program Tx Amplitude */
+ val = readl(qphy->base + PCIE20_PARF_PCS_SWING_CTRL1);
+ val &= ~0x7f;
+ val |= TX_AMP_VAL;
+ writel(val, qphy->base + PCIE20_PARF_PCS_SWING_CTRL1);
+
+ val = readl(qphy->base + PCIE20_PARF_PCS_SWING_CTRL2);
+ val &= ~0x7f;
+ val |= TX_AMP_VAL;
+ writel(val, qphy->base + PCIE20_PARF_PCS_SWING_CTRL2);
+
+ /* Program De-Emphasis */
+ val = readl(qphy->base + PCIE20_PARF_PCS_DEEMPH1);
+ val &= ~0x3f;
+ val |= TX_DEEMPH_GEN2_6DB_VAL;
+ writel(val, qphy->base + PCIE20_PARF_PCS_DEEMPH1);
+
+ val = readl(qphy->base + PCIE20_PARF_PCS_DEEMPH2);
+ val &= ~0x3f;
+ val |= TX_DEEMPH_GEN2_3_5DB_VAL;
+ writel(val, qphy->base + PCIE20_PARF_PCS_DEEMPH2);
+
+ val = readl(qphy->base + PCIE20_PARF_PCS_DEEMPH3);
+ val &= ~0x3f;
+ val |= TX_DEEMPH_GEN1_VAL;
+ writel(val, qphy->base + PCIE20_PARF_PCS_DEEMPH3);
+
+ /* Program Rx_Eq */
+ val = readl(qphy->base + PCIE20_PARF_CONFIGBITS);
+ val &= ~0x7;
+ val |= PHY_RX0_EQ_GEN2_VAL;
+ writel(val, qphy->base + PCIE20_PARF_CONFIGBITS);
+
+ /* Program Tx0_term_offset */
+ val = readl(qphy->base + PCIE20_PARF_PHY_CTRL3);
+ val &= ~0x1f;
+ val |= PHY_TX0_TERM_OFFST_VAL;
+ writel(val, qphy->base + PCIE20_PARF_PHY_CTRL3);
+
+ /* disable Tx2Rx Loopback */
+ val = readl(qphy->base + PCIE20_PARF_PCS_CTRL);
+ val &= ~BIT(1);
+ writel(val, qphy->base + PCIE20_PARF_PCS_CTRL);
+
+ /* De-assert Phy SW Reset */
+ val = readl(qphy->base + PCIE2_PHY_RESET_CTRL);
+ val &= ~BIT(0);
+ writel(val, qphy->base + PCIE2_PHY_RESET_CTRL);
+
+ usleep_range(1000, 2000);
+
+ ret = reset_control_deassert(qphy->pipe_reset);
+ if (ret) {
+ dev_err(qphy->dev, "cannot deassert pipe reset\n");
+ goto out;
+ }
+
+ clk_set_rate(qphy->pipe_clk, 250000000);
+
+ ret = clk_prepare_enable(qphy->pipe_clk);
+ if (ret) {
+ dev_err(qphy->dev, "failed to enable pipe clock\n");
+ goto out;
+ }
+
+ ret = readl_poll_timeout(qphy->base + PCIE20_PARF_PHY_STTS, val,
+ !(val & BIT(0)), 1000, 10);
+ if (ret)
+ dev_err(qphy->dev, "phy initialization failed\n");
+
+out:
+ return ret;
+}
+
+static int qcom_pcie2_phy_power_off(struct phy *phy)
+{
+ struct qcom_phy *qphy = phy_get_drvdata(phy);
+ u32 val;
+
+ val = readl(qphy->base + PCIE2_PHY_RESET_CTRL);
+ val |= BIT(0);
+ writel(val, qphy->base + PCIE2_PHY_RESET_CTRL);
+
+ clk_disable_unprepare(qphy->pipe_clk);
+ reset_control_assert(qphy->pipe_reset);
+
+ return 0;
+}
+
+static int qcom_pcie2_phy_exit(struct phy *phy)
+{
+ struct qcom_phy *qphy = phy_get_drvdata(phy);
+
+ regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
+ reset_control_assert(qphy->phy_reset);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_pcie2_ops = {
+ .init = qcom_pcie2_phy_init,
+ .power_on = qcom_pcie2_phy_power_on,
+ .power_off = qcom_pcie2_phy_power_off,
+ .exit = qcom_pcie2_phy_exit,
+ .owner = THIS_MODULE,
+};
+
+/*
+ * Register a fixed rate pipe clock.
+ *
+ * The <s>_pipe_clksrc generated by PHY goes to the GCC that gate
+ * controls it. The <s>_pipe_clk coming out of the GCC is requested
+ * by the PHY driver for its operations.
+ * We register the <s>_pipe_clksrc here. The gcc driver takes care
+ * of assigning this <s>_pipe_clksrc as parent to <s>_pipe_clk.
+ * Below picture shows this relationship.
+ *
+ * +---------------+
+ * | PHY block |<<---------------------------------------+
+ * | | |
+ * | +-------+ | +-----+ |
+ * I/P---^-->| PLL |---^--->pipe_clksrc--->| GCC |--->pipe_clk---+
+ * clk | +-------+ | +-----+
+ * +---------------+
+ */
+static int phy_pipe_clksrc_register(struct qcom_phy *qphy)
+{
+ struct device_node *np = qphy->dev->of_node;
+ struct clk_fixed_rate *fixed;
+ struct clk_init_data init = { };
+ int ret;
+
+ ret = of_property_read_string(np, "clock-output-names", &init.name);
+ if (ret) {
+ dev_err(qphy->dev, "%s: No clock-output-names\n", np->name);
+ return ret;
+ }
+
+ fixed = devm_kzalloc(qphy->dev, sizeof(*fixed), GFP_KERNEL);
+ if (!fixed)
+ return -ENOMEM;
+
+ init.ops = &clk_fixed_rate_ops;
+
+ /* controllers using QMP phys use 250MHz pipe clock interface */
+ fixed->fixed_rate = 250000000;
+ fixed->hw.init = &init;
+
+ return devm_clk_hw_register(qphy->dev, &fixed->hw);
+}
+
+static int qcom_pcie2_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct qcom_phy *qphy;
+ struct resource *res;
+ struct device *dev = &pdev->dev;
+ struct phy *phy;
+ int ret;
+
+ qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
+ if (!qphy)
+ return -ENOMEM;
+
+ qphy->dev = dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ qphy->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(qphy->base))
+ return PTR_ERR(qphy->base);
+
+ ret = phy_pipe_clksrc_register(qphy);
+ if (ret) {
+ dev_err(dev, "failed to register pipe_clk\n");
+ return ret;
+ }
+
+ qphy->vregs[0].supply = "vdda-vp";
+ qphy->vregs[1].supply = "vdda-vph";
+ ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(qphy->vregs), qphy->vregs);
+ if (ret < 0)
+ return ret;
+
+ qphy->pipe_clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(qphy->pipe_clk)) {
+ dev_err(dev, "failed to acquire pipe clock\n");
+ return PTR_ERR(qphy->pipe_clk);
+ }
+
+ qphy->phy_reset = devm_reset_control_get_exclusive(dev, "phy");
+ if (IS_ERR(qphy->phy_reset)) {
+ dev_err(dev, "failed to acquire phy reset\n");
+ return PTR_ERR(qphy->phy_reset);
+ }
+
+ qphy->pipe_reset = devm_reset_control_get_exclusive(dev, "pipe");
+ if (IS_ERR(qphy->pipe_reset)) {
+ dev_err(dev, "failed to acquire pipe reset\n");
+ return PTR_ERR(qphy->pipe_reset);
+ }
+
+ phy = devm_phy_create(dev, dev->of_node, &qcom_pcie2_ops);
+ if (IS_ERR(phy)) {
+ dev_err(dev, "failed to create phy\n");
+ return PTR_ERR(phy);
+ }
+
+ phy_set_drvdata(phy, qphy);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider))
+ dev_err(dev, "failed to register phy provider\n");
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id qcom_pcie2_phy_match_table[] = {
+ { .compatible = "qcom,pcie2-phy" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, qcom_pcie2_phy_match_table);
+
+static struct platform_driver qcom_pcie2_phy_driver = {
+ .probe = qcom_pcie2_phy_probe,
+ .driver = {
+ .name = "phy-qcom-pcie2",
+ .of_match_table = qcom_pcie2_phy_match_table,
+ },
+};
+
+module_platform_driver(qcom_pcie2_phy_driver);
+
+MODULE_DESCRIPTION("Qualcomm PCIe PHY driver");
+MODULE_LICENSE("GPL v2");
--
2.18.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
2019-05-02 0:14 ` [PATCH v3 1/2] dt-bindings: phy: Add binding for " Bjorn Andersson
@ 2019-05-02 21:36 ` Rob Herring
0 siblings, 0 replies; 6+ messages in thread
From: Rob Herring @ 2019-05-02 21:36 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Kishon Vijay Abraham I, Mark Rutland, linux-arm-msm,
linux-kernel, devicetree
On Wed, 1 May 2019 17:14:05 -0700, Bjorn Andersson wrote:
> The Qualcomm PCIe2 PHY is a Synopsys based PCIe PHY found in a number of
> Qualcomm platforms, add a binding to describe this.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
>
> Changes since v2:
> - Add #clock-cells
>
> .../bindings/phy/qcom-pcie2-phy.txt | 42 +++++++++++++++++++
> 1 file changed, 42 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v3 0/2] Qualcomm PCIe2 PHY
2019-05-02 0:14 ` Bjorn Andersson
` (2 preceding siblings ...)
(?)
@ 2019-05-29 1:00 ` Bjorn Andersson
-1 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2019-05-29 1:00 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Rob Herring, Mark Rutland, linux-arm-msm, linux-kernel, devicetree
On Wed 01 May 17:14 PDT 2019, Bjorn Andersson wrote:
> The Qualcomm PCIe2 PHY is based on design from Synopsys and found in
> several different platforms where the QMP PHY isn't used.
>
Kishon, any feedback on this or would you be willing to pick it up?
Regards,
Bjorn
> Bjorn Andersson (2):
> dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
> phy: qcom: Add Qualcomm PCIe2 PHY driver
>
> .../bindings/phy/qcom-pcie2-phy.txt | 42 +++
> drivers/phy/qualcomm/Kconfig | 8 +
> drivers/phy/qualcomm/Makefile | 1 +
> drivers/phy/qualcomm/phy-qcom-pcie2.c | 331 ++++++++++++++++++
> 4 files changed, 382 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt
> create mode 100644 drivers/phy/qualcomm/phy-qcom-pcie2.c
>
> --
> 2.18.0
>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2019-05-29 1:00 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-02 0:14 [PATCH v3 0/2] Qualcomm PCIe2 PHY Bjorn Andersson
2019-05-02 0:14 ` Bjorn Andersson
2019-05-02 0:14 ` [PATCH v3 1/2] dt-bindings: phy: Add binding for " Bjorn Andersson
2019-05-02 21:36 ` Rob Herring
2019-05-02 0:14 ` [PATCH v3 2/2] phy: qcom: Add Qualcomm PCIe2 PHY driver Bjorn Andersson
2019-05-29 1:00 ` [PATCH v3 0/2] Qualcomm PCIe2 PHY Bjorn Andersson
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.