From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Andy Gross <agross@kernel.org>, David Brown <david.brown@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v3] arm64: dts: qcom: qcs404: Add PCIe related nodes
Date: Wed, 1 May 2019 17:24:08 -0700 [thread overview]
Message-ID: <20190502002408.10719-1-bjorn.andersson@linaro.org> (raw)
The QCS404 has a PCIe2 PHY and a Qualcomm PCIe controller, add these to
the platform dtsi and enable them for the EVB with the perst gpio
and analog supplies defined.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
The patch depends on the acceptance of:
https://lore.kernel.org/lkml/20190502002138.10646-1-bjorn.andersson@linaro.org/
https://lore.kernel.org/lkml/20190502001406.10431-2-bjorn.andersson@linaro.org/
https://lore.kernel.org/lkml/20190502001955.10575-3-bjorn.andersson@linaro.org/
Changes since v2:
- None
arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 25 +++++++++
arch/arm64/boot/dts/qcom/qcs404.dtsi | 67 ++++++++++++++++++++++++
2 files changed, 92 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index 2c3127167e3c..988d21ca0df1 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -68,6 +68,22 @@
};
};
+&pcie {
+ status = "ok";
+
+ perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&perst_state>;
+};
+
+&pcie_phy {
+ status = "ok";
+
+ vdda-vp-supply = <&vreg_l3_1p05>;
+ vdda-vph-supply = <&vreg_l5_1p8>;
+};
+
&remoteproc_adsp {
status = "ok";
};
@@ -184,6 +200,15 @@
};
&tlmm {
+ perst_state: perst {
+ pins = "gpio43";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
sdc1_on: sdc1-on {
clk {
pins = "sdc1_clk";
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index ffedf9640af7..f41feab8996c 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -4,6 +4,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-qcs404.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/gpio/gpio.h>
/ {
interrupt-parent = <&intc>;
@@ -383,6 +384,7 @@
compatible = "qcom,gcc-qcs404";
reg = <0x01800000 0x80000>;
#clock-cells = <1>;
+ #reset-cells = <1>;
assigned-clocks = <&gcc GCC_APSS_AHB_CLK_SRC>;
assigned-clock-rates = <19200000>;
@@ -411,6 +413,21 @@
#interrupt-cells = <4>;
};
+ pcie_phy: phy@7786000 {
+ compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
+ reg = <0x07786000 0xb8>;
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
+ <&gcc GCC_PCIE_0_PIPE_ARES>;
+ reset-names = "phy", "pipe";
+
+ clock-output-names = "pcie_0_pipe_clk";
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
sdcc1: sdcc@7804000 {
compatible = "qcom,sdhci-msm-v5";
reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
@@ -796,6 +813,56 @@
status = "disabled";
};
};
+
+ pcie: pci@10000000 {
+ compatible = "qcom,pcie-qcs404", "snps,dw-pcie";
+ reg = <0x10000000 0xf1d>,
+ <0x10000f20 0xa8>,
+ <0x07780000 0x2000>,
+ <0x10001000 0x2000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0 0x10003000 0 0x00010000>, /* I/O */
+ <0x82000000 0 0x10013000 0x10013000 0 0x007ed000>; /* memory */
+
+ interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+ clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_AXI_CLK>;
+ clock-names = "iface", "aux", "master_bus", "slave_bus";
+
+ resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>,
+ <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>,
+ <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>,
+ <&gcc GCC_PCIE_0_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE_0_BCR>,
+ <&gcc GCC_PCIE_0_AHB_ARES>;
+ reset-names = "axi_m",
+ "axi_s",
+ "axi_m_sticky",
+ "pipe_sticky",
+ "pwr",
+ "ahb";
+
+ phys = <&pcie_phy>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
};
timer {
--
2.18.0
next reply other threads:[~2019-05-02 0:24 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-02 0:24 Bjorn Andersson [this message]
2019-05-02 11:51 ` [PATCH v3] arm64: dts: qcom: qcs404: Add PCIe related nodes Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190502002408.10719-1-bjorn.andersson@linaro.org \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.