* [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-09 2:03 Brian Masney
2019-05-09 2:03 ` [PATCH v2 1/6] drm: msm: remove resv fields from msm_gem_object struct Brian Masney
` (7 more replies)
0 siblings, 8 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark, sean, dri-devel, linux-arm-msm, freedreno, airlied,
daniel, linux-kernel, linus.walleij, jonathan, robh
Here is a patch series that adds initial display support for the LG
Nexus 5 (hammerhead) phone. It's not fully working so that's why some
of these patches are RFC until we can get it fully working.
The phones boots into terminal mode, however there is a several second
(or more) delay when writing to tty1 compared to when the changes are
actually shown on the screen. The following errors are in dmesg:
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:32:plane-0] flip_done timed out
WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1430 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[CRTC:49:crtc-0] vblank wait timed out
Modules linked in:
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.1.0-rc6-next-20190426-00006-g35c0d32a96e1-dirty #191
Hardware name: Generic DT based system
Workqueue: events deferred_probe_work_func
[<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[<c030d5ac>] (show_stack) from [<c0ac134c>] (dump_stack+0x78/0x8c)
[<c0ac134c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[<c03216e0>] (warn_slowpath_fmt) from [<c0761a0c>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[<c0761a0c>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0a98>] (mdp5_complete_commit+0x14/0x40)
[<c07b0a98>] (mdp5_complete_commit) from [<c07ddb80>] (msm_atomic_commit_tail+0xa8/0x140)
[<c07ddb80>] (msm_atomic_commit_tail) from [<c0763304>] (commit_tail+0x40/0x6c)
[<c07633f4>] (drm_atomic_helper_commit) from [<c07667f0>] (restore_fbdev_mode_atomic+0x168/0x1d4)
....
I can get the text console to work with a 4.17 kernel with this patch
https://patchwork.kernel.org/patch/10321845/ plus about a dozen or more
other patches that have been mainlined since that release.
I'm new to the DRM subsystem and continuing to dig into the issue,
however I'd appreciate any suggestions. I suspect the issue lies
somewhere in the second patch in this series.
Changes since v1:
- Shortened problem description above. I'll reply to this email and send
a full dmesg with the boot log with debugging turned on.
- Dropped patch 'fix null pointer dereference in
msm_atomic_prepare_fb()'
- New patch: Remove resv fields from msm_gem_object struct that was
incorrectly being referenced by the prepare_fb callbacks.
- Add drm_plane_enable_fb_damage_clips() to plane init for mdp4, mdp5,
and dpu1.
- Add Linus Walleij's reviewed-by to patches 3-6
Brian Masney (6):
drm: msm: remove resv fields from msm_gem_object struct
drm: msm: add dirty framebuffer helper
ARM: qcom_defconfig: add display-related options
ARM: dts: msm8974: add display support
ARM: dts: qcom: msm8974-hammerhead: add support for backlight
ARM: dts: qcom: msm8974-hammerhead: add support for display
.../qcom-msm8974-lge-nexus5-hammerhead.dts | 79 +++++++++++
arch/arm/boot/dts/qcom-msm8974.dtsi | 132 ++++++++++++++++++
arch/arm/configs/qcom_defconfig | 5 +
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 7 +-
drivers/gpu/drm/msm/disp/mdp4/mdp4_plane.c | 3 +
drivers/gpu/drm/msm/disp/mdp5/mdp5_plane.c | 3 +
drivers/gpu/drm/msm/msm_atomic.c | 4 +-
drivers/gpu/drm/msm/msm_fb.c | 2 +
drivers/gpu/drm/msm/msm_gem.c | 3 -
drivers/gpu/drm/msm/msm_gem.h | 4 -
10 files changed, 229 insertions(+), 13 deletions(-)
--
2.20.1
^ permalink raw reply [flat|nested] 35+ messages in thread
* [PATCH v2 1/6] drm: msm: remove resv fields from msm_gem_object struct
2019-05-09 2:03 [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support Brian Masney
@ 2019-05-09 2:03 ` Brian Masney
2019-05-13 20:32 ` Bjorn Andersson
2019-05-09 2:03 ` [PATCH RFC v2 2/6] drm: msm: add dirty framebuffer helper Brian Masney
` (6 subsequent siblings)
7 siblings, 1 reply; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark, sean, dri-devel, linux-arm-msm, freedreno, airlied,
daniel, linux-kernel, linus.walleij, jonathan, robh
The msm_gem_object structure contains resv and _resv fields that are
no longer needed since the reservation object is now stored on
drm_gem_object. msm_atomic_prepare_fb() and msm_atomic_prepare_fb()
both referenced the wrong reservation object, and would lead to an
attempt to dereference a NULL pointer. Correct those two cases to
point to the correct reservation object.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Fixes: dd55cf6929e6 ("drm: msm: Switch to use drm_gem_object reservation_object")
---
Patch introduced in v2
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 4 +---
drivers/gpu/drm/msm/msm_atomic.c | 4 +---
drivers/gpu/drm/msm/msm_gem.c | 3 ---
drivers/gpu/drm/msm/msm_gem.h | 4 ----
4 files changed, 2 insertions(+), 13 deletions(-)
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
index da1f727d7495..ce1a555e1f31 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
@@ -780,7 +780,6 @@ static int dpu_plane_prepare_fb(struct drm_plane *plane,
struct dpu_plane_state *pstate = to_dpu_plane_state(new_state);
struct dpu_hw_fmt_layout layout;
struct drm_gem_object *obj;
- struct msm_gem_object *msm_obj;
struct dma_fence *fence;
struct dpu_kms *kms = _dpu_plane_get_kms(&pdpu->base);
int ret;
@@ -799,8 +798,7 @@ static int dpu_plane_prepare_fb(struct drm_plane *plane,
* implicit fence and fb prepare by hand here.
*/
obj = msm_framebuffer_bo(new_state->fb, 0);
- msm_obj = to_msm_bo(obj);
- fence = reservation_object_get_excl_rcu(msm_obj->resv);
+ fence = reservation_object_get_excl_rcu(obj->resv);
if (fence)
drm_atomic_set_fence_for_plane(new_state, fence);
diff --git a/drivers/gpu/drm/msm/msm_atomic.c b/drivers/gpu/drm/msm/msm_atomic.c
index f5b1256e32b6..131c23a267ee 100644
--- a/drivers/gpu/drm/msm/msm_atomic.c
+++ b/drivers/gpu/drm/msm/msm_atomic.c
@@ -49,15 +49,13 @@ int msm_atomic_prepare_fb(struct drm_plane *plane,
struct msm_drm_private *priv = plane->dev->dev_private;
struct msm_kms *kms = priv->kms;
struct drm_gem_object *obj;
- struct msm_gem_object *msm_obj;
struct dma_fence *fence;
if (!new_state->fb)
return 0;
obj = msm_framebuffer_bo(new_state->fb, 0);
- msm_obj = to_msm_bo(obj);
- fence = reservation_object_get_excl_rcu(msm_obj->resv);
+ fence = reservation_object_get_excl_rcu(obj->resv);
drm_atomic_set_fence_for_plane(new_state, fence);
diff --git a/drivers/gpu/drm/msm/msm_gem.c b/drivers/gpu/drm/msm/msm_gem.c
index 31d5a744d84f..947508e8269d 100644
--- a/drivers/gpu/drm/msm/msm_gem.c
+++ b/drivers/gpu/drm/msm/msm_gem.c
@@ -973,9 +973,6 @@ static int msm_gem_new_impl(struct drm_device *dev,
msm_obj->flags = flags;
msm_obj->madv = MSM_MADV_WILLNEED;
- if (resv)
- msm_obj->base.resv = resv;
-
INIT_LIST_HEAD(&msm_obj->submit_entry);
INIT_LIST_HEAD(&msm_obj->vmas);
diff --git a/drivers/gpu/drm/msm/msm_gem.h b/drivers/gpu/drm/msm/msm_gem.h
index c5ac781dffee..812d1b1369a5 100644
--- a/drivers/gpu/drm/msm/msm_gem.h
+++ b/drivers/gpu/drm/msm/msm_gem.h
@@ -86,10 +86,6 @@ struct msm_gem_object {
struct llist_node freed;
- /* normally (resv == &_resv) except for imported bo's */
- struct reservation_object *resv;
- struct reservation_object _resv;
-
/* For physically contiguous buffers. Used when we don't have
* an IOMMU. Also used for stolen/splashscreen buffer.
*/
--
2.20.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH RFC v2 2/6] drm: msm: add dirty framebuffer helper
2019-05-09 2:03 [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support Brian Masney
2019-05-09 2:03 ` [PATCH v2 1/6] drm: msm: remove resv fields from msm_gem_object struct Brian Masney
@ 2019-05-09 2:03 ` Brian Masney
2019-05-09 2:03 ` Brian Masney
` (5 subsequent siblings)
7 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark, sean, dri-devel, linux-arm-msm, freedreno, airlied,
daniel, linux-kernel, linus.walleij, jonathan, robh
Use drm_atomic_helper_dirtyfb() as the dirty callback in the
msm_framebuffer_funcs struct. Call drm_plane_enable_fb_damage_clips()
when the planes are initialized in mdp4, mdp5, and dpu1.
Signed-off-by: Brian Masney <masneyb@onstation.org>
---
Changes since v1:
- Add drm_plane_enable_fb_damage_clips() to plane init for mdp4, mdp5,
and dpu1.
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 3 +++
drivers/gpu/drm/msm/disp/mdp4/mdp4_plane.c | 3 +++
drivers/gpu/drm/msm/disp/mdp5/mdp5_plane.c | 3 +++
drivers/gpu/drm/msm/msm_fb.c | 2 ++
4 files changed, 11 insertions(+)
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
index ce1a555e1f31..f3d009a3dc63 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
@@ -21,6 +21,7 @@
#include <linux/debugfs.h>
#include <linux/dma-buf.h>
+#include <drm/drm_damage_helper.h>
#include <drm/drm_atomic_uapi.h>
#include "msm_drv.h"
@@ -1540,6 +1541,8 @@ struct drm_plane *dpu_plane_init(struct drm_device *dev,
if (ret)
DPU_ERROR("failed to install zpos property, rc = %d\n", ret);
+ drm_plane_enable_fb_damage_clips(plane);
+
/* success! finalize initialization */
drm_plane_helper_add(plane, &dpu_plane_helper_funcs);
diff --git a/drivers/gpu/drm/msm/disp/mdp4/mdp4_plane.c b/drivers/gpu/drm/msm/disp/mdp4/mdp4_plane.c
index 005066f7154d..2d46d1126283 100644
--- a/drivers/gpu/drm/msm/disp/mdp4/mdp4_plane.c
+++ b/drivers/gpu/drm/msm/disp/mdp4/mdp4_plane.c
@@ -15,6 +15,7 @@
* this program. If not, see <http://www.gnu.org/licenses/>.
*/
+#include <drm/drm_damage_helper.h>
#include "mdp4_kms.h"
#define DOWN_SCALE_MAX 8
@@ -391,6 +392,8 @@ struct drm_plane *mdp4_plane_init(struct drm_device *dev,
mdp4_plane_install_properties(plane, &plane->base);
+ drm_plane_enable_fb_damage_clips(plane);
+
return plane;
fail:
diff --git a/drivers/gpu/drm/msm/disp/mdp5/mdp5_plane.c b/drivers/gpu/drm/msm/disp/mdp5/mdp5_plane.c
index be13140967b4..fcb6d32c2b38 100644
--- a/drivers/gpu/drm/msm/disp/mdp5/mdp5_plane.c
+++ b/drivers/gpu/drm/msm/disp/mdp5/mdp5_plane.c
@@ -16,6 +16,7 @@
* this program. If not, see <http://www.gnu.org/licenses/>.
*/
+#include <drm/drm_damage_helper.h>
#include <drm/drm_print.h>
#include "mdp5_kms.h"
@@ -1099,6 +1100,8 @@ struct drm_plane *mdp5_plane_init(struct drm_device *dev,
mdp5_plane_install_properties(plane, &plane->base);
+ drm_plane_enable_fb_damage_clips(plane);
+
return plane;
fail:
diff --git a/drivers/gpu/drm/msm/msm_fb.c b/drivers/gpu/drm/msm/msm_fb.c
index 136058978e0f..8624a8e4025f 100644
--- a/drivers/gpu/drm/msm/msm_fb.c
+++ b/drivers/gpu/drm/msm/msm_fb.c
@@ -16,6 +16,7 @@
*/
#include <drm/drm_crtc.h>
+#include <drm/drm_damage_helper.h>
#include <drm/drm_gem_framebuffer_helper.h>
#include <drm/drm_probe_helper.h>
@@ -35,6 +36,7 @@ static struct drm_framebuffer *msm_framebuffer_init(struct drm_device *dev,
static const struct drm_framebuffer_funcs msm_framebuffer_funcs = {
.create_handle = drm_gem_fb_create_handle,
.destroy = drm_gem_fb_destroy,
+ .dirty = drm_atomic_helper_dirtyfb,
};
#ifdef CONFIG_DEBUG_FS
--
2.20.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 3/6] ARM: qcom_defconfig: add display-related options
@ 2019-05-09 2:03 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark, sean, dri-devel, linux-arm-msm, freedreno, airlied,
daniel, linux-kernel, linus.walleij, jonathan, robh
Add the CMA (Contiguous Memory Allocator) for the MSM DRM driver, the
simple panel, and the TI LM3630A driver in order to support the display
on the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes since v1:
- None
arch/arm/configs/qcom_defconfig | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/configs/qcom_defconfig b/arch/arm/configs/qcom_defconfig
index c1854751c99a..4f02636f832e 100644
--- a/arch/arm/configs/qcom_defconfig
+++ b/arch/arm/configs/qcom_defconfig
@@ -37,6 +37,7 @@ CONFIG_ARM_CPUIDLE=y
CONFIG_VFP=y
CONFIG_NEON=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_CMA=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
@@ -146,12 +147,14 @@ CONFIG_REGULATOR_QCOM_SMD_RPM=y
CONFIG_REGULATOR_QCOM_SPMI=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_DRM=y
+CONFIG_DRM_PANEL_SIMPLE=y
CONFIG_FB=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
# CONFIG_LCD_CLASS_DEVICE is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_LM3630A=y
CONFIG_BACKLIGHT_LP855X=y
CONFIG_SOUND=y
CONFIG_SND=y
@@ -262,6 +265,8 @@ CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_UTF8=y
+CONFIG_DMA_CMA=y
+CONFIG_CMA_SIZE_MBYTES=256
CONFIG_PRINTK_TIME=y
CONFIG_DYNAMIC_DEBUG=y
CONFIG_DEBUG_INFO=y
--
2.20.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 3/6] ARM: qcom_defconfig: add display-related options
@ 2019-05-09 2:03 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark-Re5JQEeQqe8AvxtiuMwx3w, sean-p7yTbzM4H96eqtR555YLDQ,
dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
freedreno-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW, airlied-cv59FeDIM0c,
daniel-/w4YWyX8dFk, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linus.walleij-QSEj5FYQhm4dnm+yROfE0A, jonathan-eSc4qw6YbEQ,
robh-DgEjT+Ai2ygdnm+yROfE0A
Add the CMA (Contiguous Memory Allocator) for the MSM DRM driver, the
simple panel, and the TI LM3630A driver in order to support the display
on the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes since v1:
- None
arch/arm/configs/qcom_defconfig | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/configs/qcom_defconfig b/arch/arm/configs/qcom_defconfig
index c1854751c99a..4f02636f832e 100644
--- a/arch/arm/configs/qcom_defconfig
+++ b/arch/arm/configs/qcom_defconfig
@@ -37,6 +37,7 @@ CONFIG_ARM_CPUIDLE=y
CONFIG_VFP=y
CONFIG_NEON=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_CMA=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
@@ -146,12 +147,14 @@ CONFIG_REGULATOR_QCOM_SMD_RPM=y
CONFIG_REGULATOR_QCOM_SPMI=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_DRM=y
+CONFIG_DRM_PANEL_SIMPLE=y
CONFIG_FB=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
# CONFIG_LCD_CLASS_DEVICE is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_LM3630A=y
CONFIG_BACKLIGHT_LP855X=y
CONFIG_SOUND=y
CONFIG_SND=y
@@ -262,6 +265,8 @@ CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_UTF8=y
+CONFIG_DMA_CMA=y
+CONFIG_CMA_SIZE_MBYTES=256
CONFIG_PRINTK_TIME=y
CONFIG_DYNAMIC_DEBUG=y
CONFIG_DEBUG_INFO=y
--
2.20.1
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 4/6] ARM: dts: msm8974: add display support
@ 2019-05-09 2:03 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark, sean, dri-devel, linux-arm-msm, freedreno, airlied,
daniel, linux-kernel, linus.walleij, jonathan, robh
Add the MDP5, DSI and DSI PHY blocks for the display found on the
msm8974 SoCs. This is based on work from msm8916.dtsi and Jonathan
Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes since v1:
- None
arch/arm/boot/dts/qcom-msm8974.dtsi | 132 ++++++++++++++++++++++++++++
1 file changed, 132 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 45b5c8ef0374..3f613c5b95a1 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -3,6 +3,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-msm8974.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/reset/qcom,gcc-msm8974.h>
#include <dt-bindings/gpio/gpio.h>
@@ -1085,6 +1086,137 @@
};
};
};
+
+ mdss: mdss@fd900000 {
+ status = "disabled";
+
+ compatible = "qcom,mdss";
+ reg = <0xfd900000 0x100>,
+ <0xfd924000 0x1000>;
+ reg-names = "mdss_phys",
+ "vbif_phys";
+
+ power-domains = <&mmcc MDSS_GDSC>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_VSYNC_CLK>;
+ clock-names = "iface",
+ "bus",
+ "vsync";
+
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mdp: mdp@fd900000 {
+ status = "disabled";
+
+ compatible = "qcom,mdp5";
+ reg = <0xfd900100 0x22000>;
+ reg-names = "mdp_phys";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0 0>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_MDP_CLK>,
+ <&mmcc MDSS_VSYNC_CLK>;
+ clock-names = "iface",
+ "bus",
+ "core",
+ "vsync";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdp5_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+
+ dsi0: dsi@fd922800 {
+ status = "disabled";
+
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0xfd922800 0x1f8>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+ assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
+ <&mmcc PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&dsi_phy0 0>,
+ <&dsi_phy0 1>;
+
+ clocks = <&mmcc MDSS_MDP_CLK>,
+ <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_BYTE0_CLK>,
+ <&mmcc MDSS_PCLK0_CLK>,
+ <&mmcc MDSS_ESC0_CLK>,
+ <&mmcc MMSS_MISC_AHB_CLK>;
+ clock-names = "mdp_core",
+ "iface",
+ "bus",
+ "byte",
+ "pixel",
+ "core",
+ "core_mmss";
+
+ phys = <&dsi_phy0>;
+ phy-names = "dsi-phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&mdp5_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi_phy0: dsi-phy@fd922a00 {
+ status = "disabled";
+
+ compatible = "qcom,dsi-phy-28nm-hpm";
+ reg = <0xfd922a00 0xd4>,
+ <0xfd922b00 0x280>,
+ <0xfd922d80 0x30>;
+ reg-names = "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+ qcom,dsi-phy-index = <0>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>;
+ clock-names = "iface";
+ };
+ };
};
smd {
--
2.20.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 4/6] ARM: dts: msm8974: add display support
@ 2019-05-09 2:03 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark-Re5JQEeQqe8AvxtiuMwx3w, sean-p7yTbzM4H96eqtR555YLDQ,
dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
freedreno-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW, airlied-cv59FeDIM0c,
daniel-/w4YWyX8dFk, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linus.walleij-QSEj5FYQhm4dnm+yROfE0A, jonathan-eSc4qw6YbEQ,
robh-DgEjT+Ai2ygdnm+yROfE0A
Add the MDP5, DSI and DSI PHY blocks for the display found on the
msm8974 SoCs. This is based on work from msm8916.dtsi and Jonathan
Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes since v1:
- None
arch/arm/boot/dts/qcom-msm8974.dtsi | 132 ++++++++++++++++++++++++++++
1 file changed, 132 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 45b5c8ef0374..3f613c5b95a1 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -3,6 +3,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-msm8974.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/reset/qcom,gcc-msm8974.h>
#include <dt-bindings/gpio/gpio.h>
@@ -1085,6 +1086,137 @@
};
};
};
+
+ mdss: mdss@fd900000 {
+ status = "disabled";
+
+ compatible = "qcom,mdss";
+ reg = <0xfd900000 0x100>,
+ <0xfd924000 0x1000>;
+ reg-names = "mdss_phys",
+ "vbif_phys";
+
+ power-domains = <&mmcc MDSS_GDSC>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_VSYNC_CLK>;
+ clock-names = "iface",
+ "bus",
+ "vsync";
+
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mdp: mdp@fd900000 {
+ status = "disabled";
+
+ compatible = "qcom,mdp5";
+ reg = <0xfd900100 0x22000>;
+ reg-names = "mdp_phys";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0 0>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_MDP_CLK>,
+ <&mmcc MDSS_VSYNC_CLK>;
+ clock-names = "iface",
+ "bus",
+ "core",
+ "vsync";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdp5_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+
+ dsi0: dsi@fd922800 {
+ status = "disabled";
+
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0xfd922800 0x1f8>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+ assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
+ <&mmcc PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&dsi_phy0 0>,
+ <&dsi_phy0 1>;
+
+ clocks = <&mmcc MDSS_MDP_CLK>,
+ <&mmcc MDSS_AHB_CLK>,
+ <&mmcc MDSS_AXI_CLK>,
+ <&mmcc MDSS_BYTE0_CLK>,
+ <&mmcc MDSS_PCLK0_CLK>,
+ <&mmcc MDSS_ESC0_CLK>,
+ <&mmcc MMSS_MISC_AHB_CLK>;
+ clock-names = "mdp_core",
+ "iface",
+ "bus",
+ "byte",
+ "pixel",
+ "core",
+ "core_mmss";
+
+ phys = <&dsi_phy0>;
+ phy-names = "dsi-phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&mdp5_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi_phy0: dsi-phy@fd922a00 {
+ status = "disabled";
+
+ compatible = "qcom,dsi-phy-28nm-hpm";
+ reg = <0xfd922a00 0xd4>,
+ <0xfd922b00 0x280>,
+ <0xfd922d80 0x30>;
+ reg-names = "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+ qcom,dsi-phy-index = <0>;
+
+ clocks = <&mmcc MDSS_AHB_CLK>;
+ clock-names = "iface";
+ };
+ };
};
smd {
--
2.20.1
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 5/6] ARM: dts: qcom: msm8974-hammerhead: add support for backlight
@ 2019-05-09 2:03 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark, sean, dri-devel, linux-arm-msm, freedreno, airlied,
daniel, linux-kernel, linus.walleij, jonathan, robh
Add necessary device tree nodes for the main LCD backlight.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
This requires this series that should be merged soon:
https://lore.kernel.org/lkml/20190424092505.6578-1-masneyb@onstation.org/
The device tree bindings have been reviewed. The driver changes have
received 3 {Reviewed,Acked}-bys.
Changes since v1:
- None
.../qcom-msm8974-lge-nexus5-hammerhead.dts | 34 +++++++++++++++++++
1 file changed, 34 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index b3b04736a159..b7cf4b1019e9 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -289,6 +289,16 @@
};
};
+ i2c11_pins: i2c11 {
+ mux {
+ pins = "gpio83", "gpio84";
+ function = "blsp_i2c11";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
i2c12_pins: i2c12 {
mux {
pins = "gpio87", "gpio88";
@@ -369,6 +379,30 @@
};
};
+ i2c@f9967000 {
+ status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c11_pins>;
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ led-controller@38 {
+ compatible = "ti,lm3630a";
+ status = "ok";
+ reg = <0x38>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ led-sources = <0 1>;
+ label = "lcd-backlight";
+ default-brightness = <200>;
+ };
+ };
+ };
+
i2c@f9968000 {
status = "ok";
pinctrl-names = "default";
--
2.20.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 5/6] ARM: dts: qcom: msm8974-hammerhead: add support for backlight
@ 2019-05-09 2:03 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark-Re5JQEeQqe8AvxtiuMwx3w, sean-p7yTbzM4H96eqtR555YLDQ,
dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
freedreno-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW, airlied-cv59FeDIM0c,
daniel-/w4YWyX8dFk, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linus.walleij-QSEj5FYQhm4dnm+yROfE0A, jonathan-eSc4qw6YbEQ,
robh-DgEjT+Ai2ygdnm+yROfE0A
Add necessary device tree nodes for the main LCD backlight.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
This requires this series that should be merged soon:
https://lore.kernel.org/lkml/20190424092505.6578-1-masneyb@onstation.org/
The device tree bindings have been reviewed. The driver changes have
received 3 {Reviewed,Acked}-bys.
Changes since v1:
- None
.../qcom-msm8974-lge-nexus5-hammerhead.dts | 34 +++++++++++++++++++
1 file changed, 34 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index b3b04736a159..b7cf4b1019e9 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -289,6 +289,16 @@
};
};
+ i2c11_pins: i2c11 {
+ mux {
+ pins = "gpio83", "gpio84";
+ function = "blsp_i2c11";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
i2c12_pins: i2c12 {
mux {
pins = "gpio87", "gpio88";
@@ -369,6 +379,30 @@
};
};
+ i2c@f9967000 {
+ status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c11_pins>;
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ led-controller@38 {
+ compatible = "ti,lm3630a";
+ status = "ok";
+ reg = <0x38>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ led-sources = <0 1>;
+ label = "lcd-backlight";
+ default-brightness = <200>;
+ };
+ };
+ };
+
i2c@f9968000 {
status = "ok";
pinctrl-names = "default";
--
2.20.1
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 6/6] ARM: dts: qcom: msm8974-hammerhead: add support for display
@ 2019-05-09 2:03 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark, sean, dri-devel, linux-arm-msm, freedreno, airlied,
daniel, linux-kernel, linus.walleij, jonathan, robh
Add initial support for the display found on the LG Nexus 5 (hammerhead)
phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes since v1:
- None
.../qcom-msm8974-lge-nexus5-hammerhead.dts | 45 +++++++++++++++++++
1 file changed, 45 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index b7cf4b1019e9..749226e18ab5 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -500,6 +500,51 @@
};
};
};
+
+ mdss@fd900000 {
+ status = "ok";
+
+ mdp@fd900000 {
+ status = "ok";
+ };
+
+ dsi@fd922800 {
+ status = "ok";
+
+ vdda-supply = <&pm8941_l2>;
+ vdd-supply = <&pm8941_lvs3>;
+ vddio-supply = <&pm8941_l12>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+
+ panel: panel@0 {
+ reg = <0>;
+ compatible = "lg,acx467akm-7";
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+ };
+
+ dsi-phy@fd922a00 {
+ status = "ok";
+
+ vddio-supply = <&pm8941_l12>;
+ };
+ };
};
&spmi_bus {
--
2.20.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 6/6] ARM: dts: qcom: msm8974-hammerhead: add support for display
@ 2019-05-09 2:03 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:03 UTC (permalink / raw)
To: robdclark-Re5JQEeQqe8AvxtiuMwx3w, sean-p7yTbzM4H96eqtR555YLDQ,
dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
freedreno-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW, airlied-cv59FeDIM0c,
daniel-/w4YWyX8dFk, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linus.walleij-QSEj5FYQhm4dnm+yROfE0A, jonathan-eSc4qw6YbEQ,
robh-DgEjT+Ai2ygdnm+yROfE0A
Add initial support for the display found on the LG Nexus 5 (hammerhead)
phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes since v1:
- None
.../qcom-msm8974-lge-nexus5-hammerhead.dts | 45 +++++++++++++++++++
1 file changed, 45 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index b7cf4b1019e9..749226e18ab5 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -500,6 +500,51 @@
};
};
};
+
+ mdss@fd900000 {
+ status = "ok";
+
+ mdp@fd900000 {
+ status = "ok";
+ };
+
+ dsi@fd922800 {
+ status = "ok";
+
+ vdda-supply = <&pm8941_l2>;
+ vdd-supply = <&pm8941_lvs3>;
+ vddio-supply = <&pm8941_l12>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+
+ panel: panel@0 {
+ reg = <0>;
+ compatible = "lg,acx467akm-7";
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+ };
+
+ dsi-phy@fd922a00 {
+ status = "ok";
+
+ vddio-supply = <&pm8941_l12>;
+ };
+ };
};
&spmi_bus {
--
2.20.1
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
^ permalink raw reply related [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-09 2:06 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:06 UTC (permalink / raw)
To: robdclark, sean, dri-devel, linux-arm-msm, freedreno, airlied,
daniel, linux-kernel, linus.walleij, jonathan, robh
[-- Attachment #1: Type: text/plain, Size: 611 bytes --]
On Wed, May 08, 2019 at 10:03:46PM -0400, Brian Masney wrote:
> Here is a patch series that adds initial display support for the LG
> Nexus 5 (hammerhead) phone. It's not fully working so that's why some
> of these patches are RFC until we can get it fully working.
>
> The phones boots into terminal mode, however there is a several second
> (or more) delay when writing to tty1 compared to when the changes are
> actually shown on the screen. The following errors are in dmesg:
I attached the full dmesg output with this patch series applied. I
enabled debugging messages for just the DRM subsystem.
Brian
[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 86486 bytes --]
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty (masneyb@ins7386) (gcc version 8.1.1 20180626 (Red Hat Cross 8.1.1-3) (GCC)) #303 SMP PREEMPT Wed May 8 21:59:17 EDT 2019
[ 0.000000] CPU: ARMv7 Processor [512f06f0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: LGE MSM 8974 HAMMERHEAD
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 256 MiB at 0x20000000
[ 0.000000] On node 0 totalpages: 491776
[ 0.000000] Normal zone: 1536 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 164096 pages, LIFO batch:31
[ 0.000000] HighMem zone: 327680 pages, LIFO batch:63
[ 0.000000] percpu: Embedded 17 pages/cpu s39756 r8192 d21684 u69632
[ 0.000000] pcpu-alloc: s39756 r8192 d21684 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 490240
[ 0.000000] Kernel command line: console=tty0 console=ttyMSM0,115200,n8 rootwait androidboot.hardware=hammerhead user_debug=31 maxcpus=2 msm_watchdog_v2.enable=1 PMOS_NO_OUTPUT_REDIRECT=1 uart_console=enable gpt=enable lge.kcal=0|0|0|x lge.rev=rev_11 androidboot.laf androidboot.emmc=true fastboot=true androidboot.serialno=019eef1708e40fd2 androidboot.bootloader=HHZ20h androidboot.baseband=msm androidboot.hardware.sku=D820 androidboot.hardware.ddr=hynix androidboot.hardware.display=orise androidboot.revision=11
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1633208K/1967104K available (8192K kernel code, 834K rwdata, 3436K rodata, 1024K init, 266K bss, 71752K reserved, 262144K cma-reserved, 1310720K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x300/0x490 with crng_init=0
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000017] Switching to timer-based delay loop, resolution 52ns
[ 0.000410] Console: colour dummy device 80x30
[ 0.000785] printk: console [tty0] enabled
[ 0.000823] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000854] pid_max: default: 32768 minimum: 301
[ 0.000984] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001014] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001504] *** VALIDATE proc ***
[ 0.001629] *** VALIDATE cgroup1 ***
[ 0.001651] *** VALIDATE cgroup2 ***
[ 0.001676] CPU: Testing write buffer coherency: ok
[ 0.001939] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.059943] Setting up static identity map for 0x300000 - 0x300060
[ 0.079942] rcu: Hierarchical SRCU implementation.
[ 0.120017] smp: Bringing up secondary CPUs ...
[ 0.200453] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.200671] smp: Brought up 1 node, 2 CPUs
[ 0.200705] SMP: Total of 2 processors activated (76.80 BogoMIPS).
[ 0.200725] CPU: All CPU(s) started in SVC mode.
[ 0.202148] devtmpfs: initialized
[ 0.211750] VFP support v0.3: implementor 51 architecture 64 part 6f variant 2 rev 0
[ 0.212072] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.212111] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.221586] pinctrl core: initialized pinctrl subsystem
[ 0.222779] NET: Registered protocol family 16
[ 0.224668] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.225901] cpuidle: using governor menu
[ 0.226527] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.226553] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.268095] vgaarb: loaded
[ 0.268597] SCSI subsystem initialized
[ 0.268816] libata version 3.00 loaded.
[ 0.269096] usbcore: registered new interface driver usbfs
[ 0.269185] usbcore: registered new interface driver hub
[ 0.269290] usbcore: registered new device driver usb
[ 0.270505] Advanced Linux Sound Architecture Driver Initialized.
[ 0.271640] clocksource: Switched to clocksource arch_sys_counter
[ 0.624778] NET: Registered protocol family 2
[ 0.625271] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.625313] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.625381] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.625472] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.625571] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.625610] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.625774] NET: Registered protocol family 1
[ 0.626294] RPC: Registered named UNIX socket transport module.
[ 0.626319] RPC: Registered udp transport module.
[ 0.626341] RPC: Registered tcp transport module.
[ 0.626363] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.626390] PCI: CLS 0 bytes, default 64
[ 0.626644] Trying to unpack rootfs image as initramfs...
[ 0.830413] Freeing initrd memory: 40224K
[ 0.831171] hw perfevents: enabled with armv7_krait PMU driver, 5 counters available
[ 0.833228] Initialise system trusted keyrings
[ 0.833427] workingset: timestamp_bits=30 max_order=19 bucket_order=0
[ 0.840496] NFS: Registering the id_resolver key type
[ 0.840532] Key type id_resolver registered
[ 0.840554] Key type id_legacy registered
[ 0.841204] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.841533] fuse: init (API version 7.30)
[ 0.841996] Key type asymmetric registered
[ 0.842019] Asymmetric key parser 'x509' registered
[ 0.842090] bounce: pool size: 64 pages
[ 0.842145] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.842172] io scheduler mq-deadline registered
[ 0.842195] io scheduler kyber registered
[ 0.865206] msm_serial f991d000.serial: msm_serial: detected port #0
[ 0.865268] msm_serial f991d000.serial: uartclk = 7372800
[ 0.865339] f991d000.serial: ttyMSM0 at MMIO 0xf991d000 (irq = 27, base_baud = 460800) is a MSM
[ 0.865386] msm_serial: console setup on port #0
[ 1.437147] printk: console [ttyMSM0] enabled
[ 1.442335] msm_serial: driver initialized
[ 1.446406] [drm:drm_core_init] Initialized
[ 1.450208] [drm:msm_drm_register] init
[ 1.454316] [drm:msm_mdp_register]
[ 1.458422] [drm:msm_dsi_register]
[ 1.461972] [drm:msm_edp_register]
[ 1.466480] [drm:mdp5_dev_probe]
[ 1.469612] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 1.472059] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 1.495818] brd: module loaded
[ 1.505768] loop: module loaded
[ 1.506371] SCSI Media Changer driver v0.25
[ 1.508855] spmi spmi-0: PMIC arbiter version v1 (0x20000002)
[ 1.521054] GPIO line 360 (otg-gpio) hogged as output/high
[ 1.526208] s1: supplied by regulator-dummy
[ 1.526582] s2: supplied by regulator-dummy
[ 1.529836] s3: supplied by regulator-dummy
[ 1.534087] s4: Bringing 5100000uV into 5000000-5000000uV
[ 1.538148] l1: supplied by regulator-dummy
[ 1.543792] l2: supplied by regulator-dummy
[ 1.547731] l3: supplied by regulator-dummy
[ 1.551921] l4: supplied by regulator-dummy
[ 1.556056] l5: supplied by regulator-dummy
[ 1.560244] l6: supplied by regulator-dummy
[ 1.564423] l7: supplied by regulator-dummy
[ 1.568574] l8: supplied by regulator-dummy
[ 1.572765] l9: supplied by regulator-dummy
[ 1.576904] l10: supplied by regulator-dummy
[ 1.581084] l11: supplied by regulator-dummy
[ 1.585616] l12: supplied by regulator-dummy
[ 1.589867] l13: supplied by regulator-dummy
[ 1.594118] l14: supplied by regulator-dummy
[ 1.598358] l15: supplied by regulator-dummy
[ 1.602654] l16: supplied by regulator-dummy
[ 1.606863] l17: supplied by regulator-dummy
[ 1.611131] l18: supplied by regulator-dummy
[ 1.615392] l19: supplied by regulator-dummy
[ 1.619644] l20: supplied by regulator-dummy
[ 1.623921] l21: supplied by regulator-dummy
[ 1.628145] l22: supplied by regulator-dummy
[ 1.632434] l23: supplied by regulator-dummy
[ 1.636651] l24: supplied by regulator-dummy
[ 1.640922] lvs1: supplied by regulator-dummy
[ 1.645125] lvs2: supplied by regulator-dummy
[ 1.649354] lvs3: supplied by regulator-dummy
[ 1.653899] 5vs1: supplied by s4
[ 1.658101] 5vs2: supplied by s4
[ 1.662570] libphy: Fixed MDIO Bus: probed
[ 1.664506] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 1.668154] CSLIP: code copyright 1989 Regents of the University of California.
[ 1.677881] usbcore: registered new interface driver ax88179_178a
[ 1.685059] usbcore: registered new interface driver cdc_ether
[ 1.691285] usbcore: registered new interface driver net1080
[ 1.697033] usbcore: registered new interface driver cdc_subset
[ 1.702884] usbcore: registered new interface driver cdc_ncm
[ 1.708638] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.714366] ehci-pci: EHCI PCI platform driver
[ 1.720772] usbcore: registered new interface driver cdc_acm
[ 1.725110] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.746239] rtc-pm8xxx fc4cf000.spmi:pm8941@0:rtc@6000: registered as rtc0
[ 1.746476] i2c /dev entries driver
[ 1.752325] i2c_qup f9923000.i2c:
tx channel not available
[ 1.756240] i2c_qup f9925000.i2c:
tx channel not available
[ 1.770247] lm3630a_bl 2-0038: LM3630A backlight register OK.
[ 1.770594] i2c_qup f9968000.i2c:
tx channel not available
[ 1.776699] qcom-smbb fc4cf000.spmi:pm8941@0:charger@1000: Initializing SMBB rev 3
[ 1.786344] otg-vbus: supplied by 5vs1
[ 1.790745] qcom-tsens fc4a9000.thermal-sensor: tsens calibration failed
[ 1.794029] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations
[ 1.800615] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations
[ 1.807900] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations
[ 1.814941] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations
[ 1.822673] sdhci: Secure Digital Host Controller Interface driver
[ 1.829350] sdhci: Copyright(c) Pierre Ossman
[ 1.835628] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.842527] usbcore: registered new interface driver usbhid
[ 1.845757] usbhid: USB HID core driver
[ 1.854207] oprofile: using timer interrupt.
[ 1.855073] NET: Registered protocol family 17
[ 1.859449] Key type dns_resolver registered
[ 1.864071] Registering SWP/SWPB emulation handler
[ 1.868651] Loading compiled-in X.509 certificates
[ 1.903305] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 1.903386] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 1.931752] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 1.931862] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 1.954303] s1: supplied by regulator-dummy
[ 1.954396] s1: Bringing 0uV into 675000-675000uV
[ 1.961140] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 1.962969] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 1.974984] s2: supplied by regulator-dummy
[ 1.986512] s2: Bringing 0uV into 500000-500000uV
[ 1.990426] s3: supplied by regulator-dummy
[ 1.995072] s3: Bringing 0uV into 1050000-1050000uV
[ 1.999485] s4: supplied by regulator-dummy
[ 2.003931] s4: Bringing 0uV into 815000-815000uV
[ 2.008301] s5: supplied by regulator-dummy
[ 2.013266] s6: supplied by regulator-dummy
[ 2.017204] s7: supplied by regulator-dummy
[ 2.021371] s8: supplied by regulator-dummy
[ 2.025952] s1: supplied by regulator-dummy
[ 2.029413] s1: Bringing 0uV into 1300000-1300000uV
[ 2.036531] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 2.038422] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 2.050730] s2: supplied by regulator-dummy
[ 2.062206] s2: Bringing 0uV into 2150000-2150000uV
[ 2.066310] s3: supplied by regulator-dummy
[ 2.070734] s3: Bringing 0uV into 1800000-1800000uV
[ 2.076623] input: soc:gpio-keys as /devices/platform/soc/soc:gpio-keys/input/input0
[ 2.080214] rtc-pm8xxx fc4cf000.spmi:pm8941@0:rtc@6000: setting system clock to 1970-01-25T07:16:55 UTC (2099815)
[ 2.089736] wl-reg: disabling
[ 2.090219] l1: supplied by s1
[ 2.098016] ALSA device list:
[ 2.100860] l1: Bringing 0uV into 1225000-1225000uV
[ 2.103779] No soundcards found.
[ 2.107214] l2: supplied by s3
[ 2.115377] l2: Bringing 0uV into 1200000-1200000uV
[ 2.115928] l3: supplied by s1
[ 2.116580] Freeing unused kernel memory: 1024K
[ 2.119130] l3: Bringing 0uV into 1225000-1225000uV
[ 2.126986] l4: supplied by s1
[ 2.134682] l4: Bringing 0uV into 1225000-1225000uV
[ 2.137938] l5: supplied by s2
[ 2.142596] l5: Bringing 0uV into 1800000-1800000uV
[ 2.145923] l6: supplied by s2
[ 2.150452] l6: Bringing 0uV into 1800000-1800000uV
[ 2.154552] l7: supplied by s2
[ 2.158357] l7: Bringing 0uV into 1800000-1800000uV
[ 2.161841] l8: supplied by vph-pwr
[ 2.166248] l8: Bringing 0uV into 1800000-1800000uV
[ 2.170238] l9: supplied by vreg-boost
[ 2.174715] Run /init as init process
[ 2.174780] l9: Bringing 0uV into 1800000-1800000uV
[ 2.182142] mmc0: SDHCI controller on f98a4900.sdhci [f98a4900.sdhci] using ADMA
[ 2.187703] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 2.194818] l10: supplied by vreg-boost
[ 2.206363] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 2.210753] l10: Bringing 0uV into 1800000-1800000uV
[ 2.221617] l11: supplied by s1
[ 2.230312] l11: Bringing 0uV into 1300000-1300000uV
[ 2.235025] l12: supplied by s2
[ 2.239432] l12: Bringing 0uV into 1800000-1800000uV
[ 2.242907] l13: supplied by vreg-boost
[ 2.247724] l13: Bringing 0uV into 1800000-1800000uV
[ 2.251575] l14: supplied by s2
[ 2.256385] l14: Bringing 0uV into 1800000-1800000uV
[ 2.259634] l15: supplied by s2
[ 2.264420] l15: Bringing 0uV into 2050000-2050000uV
[ 2.267535] l16: supplied by vph-pwr
[ 2.272518] l16: Bringing 0uV into 2700000-2700000uV
[ 2.276242] l17: supplied by vreg-boost
[ 2.280917] l17: Bringing 0uV into 2850000-2850000uV
[ 2.284949] l18: supplied by vph-pwr
[ 2.289734] l18: Bringing 0uV into 2850000-2850000uV
[ 2.293620] l19: supplied by vph-pwr
[ 2.298259] l19: Bringing 0uV into 3000000-3000000uV
[ 2.302203] l20: supplied by vreg-boost
[ 2.306749] l20: Bringing 0uV into 2950000-2950000uV
[ 2.310787] l21: supplied by vreg-boost
[ 2.315548] l21: Bringing 0uV into 2950000-2950000uV
[ 2.319567] l22: supplied by vreg-boost
[ 2.324319] l22: Bringing 0uV into 3000000-3000000uV
[ 2.328183] l23: supplied by vreg-boost
[ 2.333080] l23: Bringing 0uV into 3000000-3000000uV
[ 2.336953] l24: supplied by vreg-boost
[ 2.341876] l24: Bringing 0uV into 3075000-3075000uV
[ 2.346008] lvs1: supplied by s3
[ 2.350968] lvs2: supplied by s3
[ 2.354222] lvs3: supplied by s3
[ 2.357474] 5vs1: supplied by regulator-dummy
[ 2.360653] 5vs2: supplied by regulator-dummy
[ 2.367752] random: fast init done
[ 2.371038] mmc0: new ultra high speed SDR104 SDIO card at address 0001
[ 2.373113] [drm:pll_28nm_register] 0
[ 2.378626] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_dc_off = 9
[ 2.382375] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_freq_seed = 31289
[ 2.388077] [drm:dsi_pll_28nm_clk_recalc_rate] vco rate = 402333398
[ 2.394525] [drm:dsi_pll_28nm_clk_recalc_rate] returning vco rate = 402333398
[ 2.401711] [drm:msm_dsi_pll_init] DSI:0 PLL registered
[ 2.448289] mmc1: SDHCI controller on f9824900.sdhci [f9824900.sdhci] using ADMA
[ 2.448730] [drm:mdp5_mdss_init]
[ 2.455563] [drm:mdp5_bind]
[ 2.458257] [drm:get_clk] skipping lut
[ 2.461016] [drm:msm_runtime_resume]
[ 2.464538] [drm:mdp5_mdss_enable]
[ 2.468324] [drm:mdp5_runtime_resume]
[ 2.471553] [drm:mdp5_enable]
[ 2.475559] [drm:mdp5_runtime_suspend]
[ 2.478538] [drm:mdp5_disable]
[ 2.482321] msm_mdp fd900100.mdp: [drm:mdp5_bind] MDP5 version v1.2
[ 2.485404] [drm:mdp5_cfg_init] MDP5: msm8x74 hw config selected
[ 2.491686] [drm:mdp5_ctlm_init] Pool of 5 CTLs created.
[ 2.497932] msm fd900000.mdss: bound fd900100.mdp (ops mdp5_ops)
[ 2.503229] [drm:dsi_bind]
[ 2.509184] [drm:dsi_bind] dsi probed=(ptrval)
[ 2.511936] msm_dsi fd922800.dsi: fd922800.dsi supply gdsc not found, using dummy regulator
[ 2.516320] [drm:msm_dsi_host_init] dsi_get_config: Version 3:10010000
[ 2.524587] msm_dsi fd922800.dsi: fd922800.dsi supply gdsc not found, using dummy regulator
[ 2.532920] [drm:msm_dsi_host_init] Dsi Host 0 initialized
[ 2.540829] [drm:msm_dsi_runtime_resume] id=0
[ 2.546386] panel-simple-dsi fd922800.dsi.0: fd922800.dsi.0 supply power not found, using dummy regulator
[ 2.550819] [drm:dsi_host_attach] id=0
[ 2.560278] msm fd900000.mdss: bound fd922800.dsi (ops dsi_ops)
[ 2.563869] [drm] using 16m VRAM carveout
[ 2.569691] [drm:msm_dsi_runtime_suspend]
[ 2.579129] msm fd900000.mdss: [drm:msm_drm_bind] VRAM: 20100000->21100000
[ 2.579284] [drm:mdp5_runtime_resume]
[ 2.584944] [drm:mdp5_enable]
[ 2.595290] mmc1: new HS200 MMC card at address 0001
[ 2.596083] mmcblk1: mmc1:0001 SEM16G 14.7 GiB
[ 2.599616] mmcblk1boot0: mmc1:0001 SEM16G partition 1 4.00 MiB
[ 2.611955] mmcblk1boot1: mmc1:0001 SEM16G partition 2 4.00 MiB
[ 2.612178] mmcblk1rpmb: mmc1:0001 SEM16G partition 3 4.00 MiB, chardev (247:0)
[ 2.617161] msm_mdp fd900100.mdp: [drm:mdp5_kms_init] no iommu, fallback to phys contig buffers for scanout
[ 2.624150] [drm:mdp5_runtime_suspend]
[ 2.633911] [drm:mdp5_disable]
[ 2.637722] msm fd900000.mdss: fall back to the other CTL category for INTF 1!
[ 2.640653] [drm:mdp5_ctlm_request] CTL 0 allocated
[ 2.648547] [drm:mdp5_runtime_resume]
[ 2.653040] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29
[ 2.659516] [drm:mdp5_enable]
[ 2.672935] [drm:mdp5_runtime_suspend]
[ 2.672969] [drm:mdp5_disable]
[ 2.675763] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.678704] [drm] Driver supports precise vblank timestamp query.
[ 2.685346] [drm:drm_irq_install] irq=78
[ 2.691558] [drm:mdp5_runtime_resume]
[ 2.695572] [drm:mdp5_enable]
[ 2.699132] [drm:mdp5_runtime_suspend]
[ 2.702167] [drm:mdp5_disable]
[ 2.705932] [drm:mdp5_runtime_resume]
[ 2.708996] [drm:mdp5_enable]
[ 2.712878] [drm:mdp5_runtime_suspend]
[ 2.715855] [drm:mdp5_disable]
[ 2.719602] [drm:drm_minor_register]
[ 2.723028] [drm:drm_minor_register] new minor registered 128
[ 2.726537] [drm:drm_minor_register]
[ 2.732556] [drm:drm_minor_register] new minor registered 0
[ 2.736029] [drm:drm_sysfs_connector_add] adding "DSI-1" to sysfs
[ 2.741296] [drm:drm_sysfs_hotplug_event] generating hotplug event
[ 2.747642] [drm] Initialized msm 1.5.0 20130625 for fd900000.mdss on minor 0
[ 2.753657] [drm:drm_mode_object_get] OBJ ID: 31 (2)
[ 2.760825] [drm:drm_setup_crtcs]
[ 2.765883] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:31:DSI-1]
[ 2.769079] [drm:dsi_mgr_connector_detect] id=0
[ 2.776303] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:31:DSI-1] status updated from unknown to connected
[ 2.780725] [drm:dsi_mgr_connector_mode_valid]
[ 2.791490] [drm:dsi_mgr_connector_mode_valid] requested=150000000, actual=150000000
[ 2.796056] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:31:DSI-1] probed modes :
[ 2.804007] [drm:drm_mode_debug_printmodeline] Modeline "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0
[ 2.812427] [drm:drm_setup_crtcs] connector 31 enabled? yes
[ 2.823697] [drm:drm_setup_crtcs] Not using firmware configuration
[ 2.829233] [drm:drm_setup_crtcs] looking for cmdline mode on connector 31
[ 2.835510] [drm:drm_setup_crtcs] looking for preferred mode on connector 31 0
[ 2.842363] [drm:drm_setup_crtcs] found mode 1080x1920
[ 2.849539] [drm:drm_setup_crtcs] picking CRTCs for 65535x65535 config
[ 2.854690] [drm:drm_setup_crtcs] desired mode 1080x1920 set on crtc 49 (0,0)
[ 2.861197] [drm:drm_mode_object_get] OBJ ID: 31 (2)
[ 2.868418] [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
[ 2.873457] [drm:msm_fbdev_create] create fbdev: 1080x1920@32 (1080x1920)
[ 2.881142] [drm:msm_alloc_stolen_fb] allocating 8355840 bytes for fb 0
[ 2.888552] [drm:msm_framebuffer_init] create framebuffer: dev=(ptrval), mode_cmd=(ptrval) (1080x1920@XR24)
[ 2.894379] [drm:msm_framebuffer_init] create: FB ID: 50 ((ptrval))
[ 2.904088] [drm:msm_fbdev_create] fbi=(ptrval), dev=(ptrval)
[ 2.910401] [drm:msm_fbdev_create] par=(ptrval), 1080x1920
[ 2.916232] [drm:msm_fbdev_create] allocated 1080x1920 fb
[ 2.922042] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 2.922064] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 2.922081] [drm:drm_atomic_get_plane_state] Added [PLANE:35:plane-1] (ptrval) state to (ptrval)
[ 2.922095] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:35:plane-1] state (ptrval)
[ 2.922112] [drm:drm_atomic_get_plane_state] Added [PLANE:37:plane-2] (ptrval) state to (ptrval)
[ 2.922125] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:37:plane-2] state (ptrval)
[ 2.922142] [drm:drm_atomic_get_plane_state] Added [PLANE:39:plane-3] (ptrval) state to (ptrval)
[ 2.922154] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:39:plane-3] state (ptrval)
[ 2.922170] [drm:drm_atomic_get_plane_state] Added [PLANE:41:plane-4] (ptrval) state to (ptrval)
[ 2.922183] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:41:plane-4] state (ptrval)
[ 2.922199] [drm:drm_atomic_get_plane_state] Added [PLANE:43:plane-5] (ptrval) state to (ptrval)
[ 2.922212] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:43:plane-5] state (ptrval)
[ 2.922228] [drm:drm_atomic_get_plane_state] Added [PLANE:45:plane-6] (ptrval) state to (ptrval)
[ 2.922241] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:45:plane-6] state (ptrval)
[ 2.922257] [drm:drm_atomic_get_plane_state] Added [PLANE:47:plane-7] (ptrval) state to (ptrval)
[ 2.922270] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:47:plane-7] state (ptrval)
[ 2.922288] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 2.922308] [drm:drm_atomic_set_mode_for_crtc] Set [MODE:1080x1920] for [CRTC:49:crtc-0] state (ptrval)
[ 2.922325] [drm:drm_atomic_set_crtc_for_plane] Link [PLANE:32:plane-0] state (ptrval) to [CRTC:49:crtc-0]
[ 2.922339] [drm:drm_atomic_set_fb_for_plane] Set [FB:50] for [PLANE:32:plane-0] state (ptrval)
[ 2.922350] [drm:drm_mode_object_get] OBJ ID: 50 (1)
[ 2.922368] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval)
[ 2.922384] [drm:drm_mode_object_get] OBJ ID: 31 (3)
[ 2.922399] [drm:drm_atomic_get_connector_state] Added [CONNECTOR:31:DSI-1] (ptrval) state to (ptrval)
[ 2.922410] [drm:drm_mode_object_get] OBJ ID: 31 (4)
[ 2.922427] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [CRTC:49:crtc-0]
[ 2.922439] [drm:drm_atomic_check_only] checking (ptrval)
[ 2.922460] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] mode changed
[ 2.922473] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] enable changed
[ 2.922486] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] active changed
[ 2.922497] [drm:dsi_mgr_connector_best_encoder]
[ 2.922513] [drm:drm_atomic_helper_check_modeset] Updating routing for [CONNECTOR:31:DSI-1]
[ 2.922523] [drm:dsi_mgr_connector_best_encoder]
[ 2.922544] [drm:drm_atomic_helper_check_modeset] [CONNECTOR:31:DSI-1] using [ENCODER:30:DSI-30] on [CRTC:49:crtc-0]
[ 2.922559] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] needs all connectors, enable: y, active: y
[ 2.922575] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval)
[ 2.922593] [drm:drm_atomic_add_affected_planes] Adding all current planes for [CRTC:49:crtc-0] to (ptrval)
[ 2.922610] [drm:drm_atomic_normalize_zpos] [CRTC:49:crtc-0] calculating normalized zpos values
[ 2.922625] [drm:drm_atomic_normalize_zpos] [PLANE:32:plane-0] processing zpos value 0
[ 2.922639] [drm:drm_atomic_normalize_zpos] [PLANE:32:plane-0] normalized zpos value 0
[ 2.922654] [drm:mdp5_plane_atomic_check] plane-0: check (0 -> 0)
[ 2.922678] [drm:drm_atomic_get_private_obj_state] Added new private object (ptrval) state (ptrval) to (ptrval)
[ 2.922694] [drm:mdp5_pipe_assign] DMA0: alloc SMP blocks
[ 2.922708] [drm:mdp5_smp_assign] DMA0[0]: request 3 SMP blocks
[ 2.922724] [drm:mdp5_pipe_assign] DMA0: assign to plane plane-0 for caps 0
[ 2.922740] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 2.922755] [drm:mdp5_mixer_assign] assigning Layer Mixer 0 to crtc crtc-0
[ 2.922772] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 2.922785] [drm:drm_atomic_commit] committing (ptrval)
[ 2.922806] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 2.922828] [drm:mdp5_runtime_resume]
[ 2.922839] [drm:mdp5_enable]
[ 2.922884] [drm:mdp5_smp_prepare_commit] assign DMA0:0, 3 blks
[ 2.922896] [drm:mdp5_smp_prepare_commit] assign DMA0:1, 3 blks
[ 2.922908] [drm:mdp5_smp_prepare_commit] assign DMA0:2, 3 blks
[ 2.922951] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 2.922964] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 2.922980] [drm:drm_atomic_helper_commit_modeset_disables] modeset on [CRTC:49:crtc-0]
[ 2.923000] [drm:mdp5_crtc_mode_set_nofb] crtc-0: set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0
[ 2.923018] [drm:drm_atomic_helper_commit_modeset_disables] modeset on [ENCODER:30:DSI-30]
[ 2.923036] [drm:dsi_mgr_bridge_mode_set] set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0
[ 2.923050] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 2.923062] [drm:mdp5_plane_atomic_update] plane-0: update
[ 2.923078] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 2.923090] [drm:mdp5_plane_mode_set] scale config = 0
[ 2.923117] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 2.923146] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 2.923161] [drm:crtc_flush] crtc-0: flush=00000840
[ 2.923179] [drm:drm_atomic_helper_commit_modeset_enables] enabling [CRTC:49:crtc-0]
[ 2.923192] [drm:mdp5_crtc_atomic_enable] crtc-0
[ 2.923210] [drm:drm_crtc_vblank_on] crtc 0, vblank enabled 0, inmodeset 0
[ 2.923238] [drm:mdp5_crtc_mode_set_nofb] crtc-0: set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0
[ 2.923260] [drm:drm_atomic_helper_commit_modeset_enables] enabling [ENCODER:30:DSI-30]
[ 2.923272] [drm:dsi_mgr_bridge_pre_enable] id=0
[ 2.923282] [drm:msm_dsi_host_reset_phy]
[ 2.927146] [drm:dsi_calc_clk_rate_6g] pclk=150000000, bclk=112500000
[ 2.927161] [drm:msm_dsi_phy_enable]
[ 2.927366] [drm:dsi_28nm_phy_enable]
[ 2.927384] [drm:msm_dsi_dphy_timing_calc] PHY timings: 44, 2, 0, 238, 56, 38, 106, 108, 44, 60, 44
[ 2.927428] [drm:msm_dsi_host_power_on]
[ 2.928075] [drm:msm_dsi_runtime_resume] id=0
[ 2.928101] [drm:dsi_link_clk_enable_6g] Set clk rates: pclk=150000, byteclk=112500000
[ 2.928170] [drm:dsi_pll_28nm_clk_set_rate] refclk_cfg = 1
[ 2.928182] [drm:dsi_pll_28nm_clk_set_rate] div_fb = 11718
[ 2.928193] [drm:dsi_pll_28nm_clk_set_rate] frac_n_value = 47054
[ 2.928204] [drm:dsi_pll_28nm_clk_set_rate] Generated VCO Clock: 449971200
[ 2.928215] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg0=0
[ 2.928226] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg1=74
[ 2.928237] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg2=206
[ 2.928248] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg3=183
[ 2.928260] [drm:dsi_pll_28nm_clk_set_rate] cal_cfg10=193, cal_cfg11=1
[ 2.928285] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_dc_off = 10
[ 2.928297] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_freq_seed = 47054
[ 2.928308] [drm:dsi_pll_28nm_clk_recalc_rate] vco rate = 449970703
[ 2.928320] [drm:dsi_pll_28nm_clk_recalc_rate] returning vco rate = 449970703
[ 2.928394] [drm:dsi_pll_28nm_enable_seq_hpm] id=0
[ 2.930017] [drm:pll_28nm_poll_for_ready] DSI PLL is locked
[ 2.930027] [drm:dsi_pll_28nm_enable_seq_hpm] DSI PLL Lock success
[ 2.930040] [drm:msm_dsi_pll_helper_clk_prepare] DSI PLL locked after sequence #1
[ 2.930061] [drm:msm_dsi_host_power_on]
[ 2.930078] [drm:dsi_intr_ctrl] intr=2000000 enable=1
[ 2.930090] [drm:msm_dsi_host_power_on] lane number=4
[ 2.930107] [drm:dsi_intr_ctrl] intr=2000200 enable=1
[ 2.930126] [drm:mdp5_cmd_encoder_mode_set] set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0
[ 2.930157] [drm:mdp5_crtc_vblank_irq] crtc-0: send event: (ptrval)
[ 2.930199] [drm:mdp5_ctl_set_encoder_state] intf_1: on
[ 2.930214] [drm:drm_bridge_enable]
[ 2.930227] [drm:msm_enable_vblank] dev=(ptrval), crtc=0
[ 2.930247] [drm:drm_vblank_enable] enabling vblank on crtc 0, ret: 0
[ 2.930266] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 2.981842] msm fd900000.mdss: pp done time out, lm=0
[ 3.041732] ------------[ cut here ]------------
[ 3.041751] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 3.041759] [CRTC:49:crtc-0] vblank wait timed out
[ 3.041764] Modules linked in:
[ 3.041784] CPU: 0 PID: 100 Comm: kworker/0:2 Not tainted 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 3.041792] Hardware name: Generic DT based system
[ 3.041812] Workqueue: events deferred_probe_work_func
[ 3.041839] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 3.041853] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 3.041871] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 3.041884] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 3.041899] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 3.041916] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 3.041937] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 3.041952] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 3.041963] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 3.041973] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4)
[ 3.041985] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c076a7d0>] (drm_fb_helper_restore_fbdev_mode_unlocked+0x54/0xa4)
[ 3.041996] [<c076a7d0>] (drm_fb_helper_restore_fbdev_mode_unlocked) from [<c076a850>] (drm_fb_helper_set_par+0x30/0x54)
[ 3.042007] [<c076a850>] (drm_fb_helper_set_par) from [<c06ef4c8>] (fbcon_init+0x4b4/0x5d4)
[ 3.042019] [<c06ef4c8>] (fbcon_init) from [<c073bf88>] (visual_init+0xbc/0x104)
[ 3.042030] [<c073bf88>] (visual_init) from [<c073dea8>] (do_bind_con_driver+0x1ec/0x3c4)
[ 3.042040] [<c073dea8>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0)
[ 3.042050] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8)
[ 3.042066] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80)
[ 3.042078] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68)
[ 3.042094] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304)
[ 3.042106] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c)
[ 3.042120] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc)
[ 3.042131] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634)
[ 3.042146] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4)
[ 3.042160] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174)
[ 3.042175] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98)
[ 3.042188] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c)
[ 3.042200] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0)
[ 3.042211] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4)
[ 3.042222] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168)
[ 3.042232] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c)
[ 3.042243] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4)
[ 3.042259] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 3.042273] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 3.042285] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 3.042297] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 3.042306] Exception stack(0xc4e09fb0 to 0xc4e09ff8)
[ 3.042325] 9fa0: 00000000 00000000 00000000 00000000
[ 3.042350] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 3.042371] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 3.042380] ---[ end trace d4b922f6bb6a2602 ]---
[ 3.042416] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 3.042430] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (5)
[ 3.042451] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 3.042514] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 3.042528] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 3.042543] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 3.042556] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 3.042571] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 3.042588] [drm:drm_atomic_get_plane_state] Added [PLANE:35:plane-1] (ptrval) state to (ptrval)
[ 3.042601] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:35:plane-1] state (ptrval)
[ 3.042617] [drm:drm_atomic_get_plane_state] Added [PLANE:37:plane-2] (ptrval) state to (ptrval)
[ 3.042630] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:37:plane-2] state (ptrval)
[ 3.042646] [drm:drm_atomic_get_plane_state] Added [PLANE:39:plane-3] (ptrval) state to (ptrval)
[ 3.042659] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:39:plane-3] state (ptrval)
[ 3.042675] [drm:drm_atomic_get_plane_state] Added [PLANE:41:plane-4] (ptrval) state to (ptrval)
[ 3.042687] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:41:plane-4] state (ptrval)
[ 3.042703] [drm:drm_atomic_get_plane_state] Added [PLANE:43:plane-5] (ptrval) state to (ptrval)
[ 3.042716] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:43:plane-5] state (ptrval)
[ 3.042732] [drm:drm_atomic_get_plane_state] Added [PLANE:45:plane-6] (ptrval) state to (ptrval)
[ 3.042745] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:45:plane-6] state (ptrval)
[ 3.042761] [drm:drm_atomic_get_plane_state] Added [PLANE:47:plane-7] (ptrval) state to (ptrval)
[ 3.042774] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:47:plane-7] state (ptrval)
[ 3.042789] [drm:drm_atomic_set_fb_for_plane] Set [FB:50] for [PLANE:32:plane-0] state (ptrval)
[ 3.042800] [drm:drm_mode_object_get] OBJ ID: 50 (3)
[ 3.042812] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (4)
[ 3.042828] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval)
[ 3.042843] [drm:drm_mode_object_get] OBJ ID: 31 (5)
[ 3.042854] [drm:drm_mode_object_get] OBJ ID: 31 (6)
[ 3.042869] [drm:drm_atomic_get_connector_state] Added [CONNECTOR:31:DSI-1] (ptrval) state to (ptrval)
[ 3.042882] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6)
[ 3.042896] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [NOCRTC]
[ 3.042907] [drm:drm_mode_object_get] OBJ ID: 31 (5)
[ 3.042924] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [CRTC:49:crtc-0]
[ 3.042936] [drm:drm_atomic_check_only] checking (ptrval)
[ 3.042949] [drm:dsi_mgr_connector_best_encoder]
[ 3.042967] [drm:drm_atomic_helper_check_modeset] Updating routing for [CONNECTOR:31:DSI-1]
[ 3.042976] [drm:dsi_mgr_connector_best_encoder]
[ 3.042996] [drm:drm_atomic_helper_check_modeset] [CONNECTOR:31:DSI-1] keeps [ENCODER:30:DSI-30], now on [CRTC:49:crtc-0]
[ 3.043012] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 3.043031] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 3.043047] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 3.043060] [drm:drm_atomic_commit] committing (ptrval)
[ 3.043078] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 3.043135] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 3.043148] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 3.043162] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 3.043173] [drm:mdp5_plane_atomic_update] plane-0: update
[ 3.043188] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 3.043199] [drm:mdp5_plane_mode_set] scale config = 0
[ 3.043223] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 3.043249] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 3.043263] [drm:crtc_flush] crtc-0: flush=00000840
[ 3.043304] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 3.101745] msm fd900000.mdss: pp done time out, lm=0
[ 3.161729] ------------[ cut here ]------------
[ 3.161746] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 3.161754] [CRTC:49:crtc-0] vblank wait timed out
[ 3.161758] Modules linked in:
[ 3.161778] CPU: 0 PID: 100 Comm: kworker/0:2 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 3.161786] Hardware name: Generic DT based system
[ 3.161803] Workqueue: events deferred_probe_work_func
[ 3.161820] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 3.161831] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 3.161844] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 3.161856] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 3.161870] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 3.161885] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 3.161900] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 3.161914] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 3.161926] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 3.161936] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4)
[ 3.161945] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c0766c48>] (drm_fb_helper_pan_display+0xc4/0x1d8)
[ 3.161957] [<c0766c48>] (drm_fb_helper_pan_display) from [<c06e7c38>] (fb_pan_display+0x9c/0x110)
[ 3.161969] [<c06e7c38>] (fb_pan_display) from [<c06f3528>] (bit_update_start+0x14/0x30)
[ 3.161979] [<c06f3528>] (bit_update_start) from [<c06f215c>] (fbcon_switch+0x390/0x514)
[ 3.161989] [<c06f215c>] (fbcon_switch) from [<c073d5d4>] (redraw_screen+0x13c/0x244)
[ 3.161999] [<c073d5d4>] (redraw_screen) from [<c06eef84>] (fbcon_prepare_logo+0x378/0x408)
[ 3.162007] [<c06eef84>] (fbcon_prepare_logo) from [<c06ef438>] (fbcon_init+0x424/0x5d4)
[ 3.162016] [<c06ef438>] (fbcon_init) from [<c073bf88>] (visual_init+0xbc/0x104)
[ 3.162025] [<c073bf88>] (visual_init) from [<c073dea8>] (do_bind_con_driver+0x1ec/0x3c4)
[ 3.162035] [<c073dea8>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0)
[ 3.162044] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8)
[ 3.162057] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80)
[ 3.162067] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68)
[ 3.162079] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304)
[ 3.162091] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c)
[ 3.162105] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc)
[ 3.162116] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634)
[ 3.162129] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4)
[ 3.162142] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174)
[ 3.162155] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98)
[ 3.162167] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c)
[ 3.162178] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0)
[ 3.162189] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4)
[ 3.162199] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168)
[ 3.162210] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c)
[ 3.162220] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4)
[ 3.162233] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 3.162246] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 3.162258] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 3.162268] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 3.162277] Exception stack(0xc4e09fb0 to 0xc4e09ff8)
[ 3.162295] 9fa0: 00000000 00000000 00000000 00000000
[ 3.162319] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 3.162340] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 3.162349] ---[ end trace d4b922f6bb6a2603 ]---
[ 3.162379] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50]
[ 3.162397] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 3.162409] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6)
[ 3.162421] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (5)
[ 3.162433] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2)
[ 3.162446] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3)
[ 3.162461] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 3.162491] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 3.162507] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 3.162519] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 3.162535] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 3.162545] [drm:drm_mode_object_get] OBJ ID: 52 (1)
[ 3.162558] [drm:drm_atomic_check_only] checking (ptrval)
[ 3.162575] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 3.162592] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 3.162609] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 3.162622] [drm:drm_atomic_commit] committing (ptrval)
[ 3.162638] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 3.581980] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 4.109986] EXT4-fs (dm-0): mounted filesystem without journal. Opts: (null)
[ 4.618939] [drm:mdp5_crtc_vblank_irq] crtc-0: send event: (ptrval)
[ 4.618983] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 4.618998] [drm:vblank_disable_fn] disabling vblank on crtc 0
[ 4.619016] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 4.619029] [drm:msm_disable_vblank] dev=(ptrval), crtc=0
[ 4.619112] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 4.619126] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 4.619142] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 4.619156] [drm:mdp5_plane_atomic_update] plane-0: update
[ 4.619173] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 4.619185] [drm:mdp5_plane_mode_set] scale config = 0
[ 4.619212] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 4.619243] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 4.619257] [drm:crtc_flush] crtc-0: flush=00000840
[ 4.619277] [drm:msm_enable_vblank] dev=(ptrval), crtc=0
[ 4.619293] [drm:drm_vblank_enable] enabling vblank on crtc 0, ret: 0
[ 4.619311] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 4.620660] [drm:dsi_host_irq] isr=0x2000700, id=0
[ 4.671711] msm fd900000.mdss: pp done time out, lm=0
[ 4.731689] ------------[ cut here ]------------
[ 4.731716] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 4.731724] [CRTC:49:crtc-0] vblank wait timed out
[ 4.731729] Modules linked in: dm_mod
[ 4.731757] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 4.731765] Hardware name: Generic DT based system
[ 4.731782] Workqueue: events drm_fb_helper_dirty_work
[ 4.731806] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 4.731820] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 4.731837] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 4.731849] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 4.731864] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 4.731885] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 4.731906] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 4.731921] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 4.731933] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 4.731948] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204)
[ 4.731960] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164)
[ 4.731975] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 4.731989] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 4.732002] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 4.732014] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 4.732023] Exception stack(0xde965fb0 to 0xde965ff8)
[ 4.732042] 5fa0: 00000000 00000000 00000000 00000000
[ 4.732067] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 4.732088] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 4.732106] ---[ end trace d4b922f6bb6a2604 ]---
[ 4.732142] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50]
[ 4.732160] [drm:drm_mode_object_put.part.0] OBJ ID: 52 (2)
[ 4.732179] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 4.732192] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2)
[ 4.732207] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3)
[ 4.732222] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 4.758491] Console: switching to colour frame buffer device 135x120
[ 4.758533] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 4.758548] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 4.758564] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 4.758578] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 4.758594] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 4.758612] [drm:drm_atomic_get_plane_state] Added [PLANE:35:plane-1] (ptrval) state to (ptrval)
[ 4.758626] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:35:plane-1] state (ptrval)
[ 4.758643] [drm:drm_atomic_get_plane_state] Added [PLANE:37:plane-2] (ptrval) state to (ptrval)
[ 4.758656] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:37:plane-2] state (ptrval)
[ 4.758673] [drm:drm_atomic_get_plane_state] Added [PLANE:39:plane-3] (ptrval) state to (ptrval)
[ 4.758686] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:39:plane-3] state (ptrval)
[ 4.758703] [drm:drm_atomic_get_plane_state] Added [PLANE:41:plane-4] (ptrval) state to (ptrval)
[ 4.758716] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:41:plane-4] state (ptrval)
[ 4.758733] [drm:drm_atomic_get_plane_state] Added [PLANE:43:plane-5] (ptrval) state to (ptrval)
[ 4.758746] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:43:plane-5] state (ptrval)
[ 4.758763] [drm:drm_atomic_get_plane_state] Added [PLANE:45:plane-6] (ptrval) state to (ptrval)
[ 4.758776] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:45:plane-6] state (ptrval)
[ 4.759026] [drm:drm_atomic_get_plane_state] Added [PLANE:47:plane-7] (ptrval) state to (ptrval)
[ 4.759040] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:47:plane-7] state (ptrval)
[ 4.759057] [drm:drm_atomic_set_fb_for_plane] Set [FB:50] for [PLANE:32:plane-0] state (ptrval)
[ 4.759069] [drm:drm_mode_object_get] OBJ ID: 50 (3)
[ 4.759080] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (4)
[ 4.759097] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval)
[ 4.759114] [drm:drm_mode_object_get] OBJ ID: 31 (5)
[ 4.759125] [drm:drm_mode_object_get] OBJ ID: 31 (6)
[ 4.759140] [drm:drm_atomic_get_connector_state] Added [CONNECTOR:31:DSI-1] (ptrval) state to (ptrval)
[ 4.759153] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6)
[ 4.759168] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [NOCRTC]
[ 4.759180] [drm:drm_mode_object_get] OBJ ID: 31 (5)
[ 4.759196] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [CRTC:49:crtc-0]
[ 4.759209] [drm:drm_atomic_check_only] checking (ptrval)
[ 4.759224] [drm:dsi_mgr_connector_best_encoder]
[ 4.759244] [drm:drm_atomic_helper_check_modeset] Updating routing for [CONNECTOR:31:DSI-1]
[ 4.759254] [drm:dsi_mgr_connector_best_encoder]
[ 4.759275] [drm:drm_atomic_helper_check_modeset] [CONNECTOR:31:DSI-1] keeps [ENCODER:30:DSI-30], now on [CRTC:49:crtc-0]
[ 4.759293] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 4.759316] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 4.759333] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 4.759347] [drm:drm_atomic_commit] committing (ptrval)
[ 4.759369] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 4.759413] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 5.840800] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[ 8.871442] udevd[752]: starting version 3.2.7
[ 8.876350] random: udevd: uninitialized urandom read (16 bytes read)
[ 8.877358] random: udevd: uninitialized urandom read (16 bytes read)
[ 8.877459] random: udevd: uninitialized urandom read (16 bytes read)
[ 8.908690] udevd[753]: starting eudev-3.2.7
[ 9.563857] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 9.588748] inv-mpu6050-i2c 3-0068: mounting matrix not found: using identity...
[ 9.606791] input: pm8941_pwrkey as /devices/platform/soc/fc4cf000.spmi/spmi-0/0-00/fc4cf000.spmi:pm8941@0:pwrkey@800/input/input1
[ 9.679456] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 9.680082] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 9.680093] cfg80211: failed to load regulatory.db
[ 9.797045] ak8975 4-000f: mounting matrix not found: using identity...
[ 9.825968] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2
[ 9.835347] brcmfmac mmc0:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.lge,hammerhead.txt failed with error -2
[ 10.163863] i2c i2c-3: Added multiplexed i2c bus 4
[ 12.344803] e cgroup1: Need name or subsystem set
[ 12.682849] urandom_read: 2 callbacks suppressed
[ 12.682860] random: mktemp: uninitialized urandom read (10 bytes read)
[ 15.201752] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out
[ 18.574025] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 19.368235] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 19.522781] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 19.955263] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 20.160328] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 20.395962] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 23.364779] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 24.303460] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 24.390171] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 25.441747] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:32:plane-0] flip_done timed out
[ 25.441806] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 25.441820] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 25.441835] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 25.441848] [drm:mdp5_plane_atomic_update] plane-0: update
[ 25.441865] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 25.441877] [drm:mdp5_plane_mode_set] scale config = 0
[ 25.441909] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 25.441914] ------------[ cut here ]------------
[ 25.441928] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c:709 mdp5_crtc_atomic_flush+0x174/0x190
[ 25.441933] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod
[ 25.442026] CPU: 0 PID: 100 Comm: kworker/0:2 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 25.442035] Hardware name: Generic DT based system
[ 25.442054] Workqueue: events deferred_probe_work_func
[ 25.442079] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 25.442094] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 25.442110] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 25.442124] [<c0321660>] (__warn.part.3) from [<c03217d8>] (warn_slowpath_null+0x44/0x4c)
[ 25.442137] [<c03217d8>] (warn_slowpath_null) from [<c07ad97c>] (mdp5_crtc_atomic_flush+0x174/0x190)
[ 25.442152] [<c07ad97c>] (mdp5_crtc_atomic_flush) from [<c075f5e0>] (drm_atomic_helper_commit_planes+0x1fc/0x270)
[ 25.442172] [<c075f5e0>] (drm_atomic_helper_commit_planes) from [<c07ddd04>] (msm_atomic_commit_tail+0x44/0x140)
[ 25.442187] [<c07ddd04>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 25.442198] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 25.442210] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4)
[ 25.442219] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c0766c48>] (drm_fb_helper_pan_display+0xc4/0x1d8)
[ 25.442234] [<c0766c48>] (drm_fb_helper_pan_display) from [<c06e7c38>] (fb_pan_display+0x9c/0x110)
[ 25.442247] [<c06e7c38>] (fb_pan_display) from [<c06f3528>] (bit_update_start+0x14/0x30)
[ 25.442257] [<c06f3528>] (bit_update_start) from [<c06f215c>] (fbcon_switch+0x390/0x514)
[ 25.442269] [<c06f215c>] (fbcon_switch) from [<c073d5d4>] (redraw_screen+0x13c/0x244)
[ 25.442280] [<c073d5d4>] (redraw_screen) from [<c073e010>] (do_bind_con_driver+0x354/0x3c4)
[ 25.442291] [<c073e010>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0)
[ 25.442300] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8)
[ 25.442317] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80)
[ 25.442329] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68)
[ 25.442341] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304)
[ 25.442354] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c)
[ 25.442371] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc)
[ 25.442383] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634)
[ 25.442399] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4)
[ 25.442412] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174)
[ 25.442427] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98)
[ 25.442441] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c)
[ 25.442452] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0)
[ 25.442463] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4)
[ 25.442474] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168)
[ 25.442484] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c)
[ 25.442494] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4)
[ 25.442510] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 25.442524] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 25.442537] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 25.442548] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 25.442558] Exception stack(0xc4e09fb0 to 0xc4e09ff8)
[ 25.442577] 9fa0: 00000000 00000000 00000000 00000000
[ 25.442601] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 25.442623] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 25.442632] ---[ end trace d4b922f6bb6a2605 ]---
[ 25.442663] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 25.442677] [drm:crtc_flush] crtc-0: flush=00000840
[ 25.501752] msm fd900000.mdss: pp done time out, lm=0
[ 25.561740] ------------[ cut here ]------------
[ 25.561758] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 25.561766] [CRTC:49:crtc-0] vblank wait timed out
[ 25.561770] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod
[ 25.561854] CPU: 0 PID: 100 Comm: kworker/0:2 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 25.561863] Hardware name: Generic DT based system
[ 25.561879] Workqueue: events deferred_probe_work_func
[ 25.561897] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 25.561908] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 25.561921] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 25.561933] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 25.561947] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 25.561963] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 25.561980] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 25.561993] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 25.562005] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 25.562015] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4)
[ 25.562024] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c0766c48>] (drm_fb_helper_pan_display+0xc4/0x1d8)
[ 25.562036] [<c0766c48>] (drm_fb_helper_pan_display) from [<c06e7c38>] (fb_pan_display+0x9c/0x110)
[ 25.562047] [<c06e7c38>] (fb_pan_display) from [<c06f3528>] (bit_update_start+0x14/0x30)
[ 25.562056] [<c06f3528>] (bit_update_start) from [<c06f215c>] (fbcon_switch+0x390/0x514)
[ 25.562066] [<c06f215c>] (fbcon_switch) from [<c073d5d4>] (redraw_screen+0x13c/0x244)
[ 25.562076] [<c073d5d4>] (redraw_screen) from [<c073e010>] (do_bind_con_driver+0x354/0x3c4)
[ 25.562085] [<c073e010>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0)
[ 25.562095] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8)
[ 25.562107] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80)
[ 25.562118] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68)
[ 25.562129] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304)
[ 25.562142] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c)
[ 25.562156] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc)
[ 25.562166] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634)
[ 25.562179] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4)
[ 25.562192] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174)
[ 25.562206] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98)
[ 25.562218] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c)
[ 25.562229] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0)
[ 25.562239] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4)
[ 25.562250] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168)
[ 25.562260] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c)
[ 25.562271] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4)
[ 25.562284] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 25.562297] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 25.562309] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 25.562319] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 25.562328] Exception stack(0xc4e09fb0 to 0xc4e09ff8)
[ 25.562345] 9fa0: 00000000 00000000 00000000 00000000
[ 25.562370] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 25.562391] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 25.562399] ---[ end trace d4b922f6bb6a2606 ]---
[ 25.562431] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50]
[ 25.562453] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 25.562467] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6)
[ 25.562480] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (5)
[ 25.562493] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2)
[ 25.562507] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3)
[ 25.562526] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 25.571673] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 25.571690] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 25.571705] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 25.571720] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 25.571732] [drm:drm_mode_object_get] OBJ ID: 53 (1)
[ 25.571745] [drm:drm_atomic_check_only] checking (ptrval)
[ 25.571767] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 25.571787] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 25.571804] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 25.571817] [drm:drm_atomic_commit] committing (ptrval)
[ 25.571836] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 26.223530] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 35.681745] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out
[ 40.478585] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 40.531284] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 40.593999] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 40.916158] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 43.157049] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 45.172624] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 45.921742] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:32:plane-0] flip_done timed out
[ 45.921787] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 45.921801] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 45.921814] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 45.921827] [drm:mdp5_plane_atomic_update] plane-0: update
[ 45.921842] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 45.921854] [drm:mdp5_plane_mode_set] scale config = 0
[ 45.921879] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 45.921884] ------------[ cut here ]------------
[ 45.921898] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c:709 mdp5_crtc_atomic_flush+0x174/0x190
[ 45.921902] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod
[ 45.921990] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 45.921998] Hardware name: Generic DT based system
[ 45.922014] Workqueue: events drm_fb_helper_dirty_work
[ 45.922034] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 45.922046] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 45.922061] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 45.922073] [<c0321660>] (__warn.part.3) from [<c03217d8>] (warn_slowpath_null+0x44/0x4c)
[ 45.922086] [<c03217d8>] (warn_slowpath_null) from [<c07ad97c>] (mdp5_crtc_atomic_flush+0x174/0x190)
[ 45.922099] [<c07ad97c>] (mdp5_crtc_atomic_flush) from [<c075f5e0>] (drm_atomic_helper_commit_planes+0x1fc/0x270)
[ 45.922115] [<c075f5e0>] (drm_atomic_helper_commit_planes) from [<c07ddd04>] (msm_atomic_commit_tail+0x44/0x140)
[ 45.922129] [<c07ddd04>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 45.922141] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 45.922156] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204)
[ 45.922169] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164)
[ 45.922182] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 45.922195] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 45.922208] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 45.922219] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 45.922228] Exception stack(0xde965fb0 to 0xde965ff8)
[ 45.922246] 5fa0: 00000000 00000000 00000000 00000000
[ 45.922271] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 45.922291] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 45.922299] ---[ end trace d4b922f6bb6a2607 ]---
[ 45.922328] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 45.922343] [drm:crtc_flush] crtc-0: flush=00000840
[ 45.981760] msm fd900000.mdss: pp done time out, lm=0
[ 46.041730] ------------[ cut here ]------------
[ 46.041748] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 46.041756] [CRTC:49:crtc-0] vblank wait timed out
[ 46.041760] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod
[ 46.041843] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 46.041851] Hardware name: Generic DT based system
[ 46.041866] Workqueue: events drm_fb_helper_dirty_work
[ 46.041884] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 46.041895] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 46.041907] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 46.041919] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 46.041933] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 46.041948] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 46.041964] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 46.041978] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 46.041990] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 46.042003] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204)
[ 46.042014] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164)
[ 46.042026] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 46.042039] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 46.042051] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 46.042061] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 46.042070] Exception stack(0xde965fb0 to 0xde965ff8)
[ 46.042087] 5fa0: 00000000 00000000 00000000 00000000
[ 46.042112] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 46.042134] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 46.042141] ---[ end trace d4b922f6bb6a2608 ]---
[ 46.042171] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50]
[ 46.042187] [drm:drm_mode_object_put.part.0] OBJ ID: 53 (2)
[ 46.042204] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 46.042215] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2)
[ 46.042230] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3)
[ 46.042244] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 46.042273] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 46.042291] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 46.042306] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 46.042320] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 46.042335] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 46.042346] [drm:drm_mode_object_get] OBJ ID: 54 (1)
[ 46.042359] [drm:drm_atomic_check_only] checking (ptrval)
[ 46.042376] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 46.042395] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 46.042411] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 46.042423] [drm:drm_atomic_commit] committing (ptrval)
[ 46.042440] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 56.161749] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out
[ 59.666659] [drm:dsi_host_irq] isr=0x2000700, id=0
[ 61.315067] [drm:mdp5_crtc_vblank_irq] crtc-0: send event: (ptrval)
[ 61.315103] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 61.315117] [drm:vblank_disable_fn] disabling vblank on crtc 0
[ 61.315136] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 61.315147] [drm:msm_disable_vblank] dev=(ptrval), crtc=0
[ 61.315220] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 61.315234] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 61.315247] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 61.315260] [drm:mdp5_plane_atomic_update] plane-0: update
[ 61.315275] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 61.315286] [drm:mdp5_plane_mode_set] scale config = 0
[ 61.315311] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 61.315337] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 61.315351] [drm:crtc_flush] crtc-0: flush=00000840
[ 61.315369] [drm:msm_enable_vblank] dev=(ptrval), crtc=0
[ 61.315388] [drm:drm_vblank_enable] enabling vblank on crtc 0, ret: 0
[ 61.315406] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 61.318527] [drm:dsi_host_irq] isr=0x2000700, id=0
[ 61.371744] msm fd900000.mdss: pp done time out, lm=0
[ 61.431730] ------------[ cut here ]------------
[ 61.431747] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 61.431754] [CRTC:49:crtc-0] vblank wait timed out
[ 61.431758] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod
[ 61.431843] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 61.431851] Hardware name: Generic DT based system
[ 61.431866] Workqueue: events drm_fb_helper_dirty_work
[ 61.431885] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 61.431896] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 61.431909] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 61.431922] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 61.431936] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 61.431952] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 61.431968] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 61.431981] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 61.431993] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 61.432006] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204)
[ 61.432017] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164)
[ 61.432031] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 61.432043] [<c033c4b0>] (process_one_work) from [<c033d384>] (worker_thread+0x2c0/0x584)
[ 61.432055] [<c033d384>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 61.432066] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 61.432075] Exception stack(0xde965fb0 to 0xde965ff8)
[ 61.432092] 5fa0: 00000000 00000000 00000000 00000000
[ 61.432117] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 61.432138] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 61.432147] ---[ end trace d4b922f6bb6a2609 ]---
[ 61.432176] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50]
[ 61.432192] [drm:drm_mode_object_put.part.0] OBJ ID: 54 (2)
[ 61.432207] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 61.432219] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2)
[ 61.432232] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3)
[ 61.432245] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 61.432373] msm fd900000.mdss: fb0: msmdrmfb frame buffer device
[ 61.432405] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 61.432423] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 61.432438] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 61.432452] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 61.432470] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 61.432482] [drm:drm_mode_object_get] OBJ ID: 55 (1)
[ 61.432496] [drm:drm_atomic_check_only] checking (ptrval)
[ 61.432515] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 61.432534] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 61.432552] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 61.432566] [drm:drm_atomic_commit] committing (ptrval)
[ 61.432583] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 62.481750] [drm:drm_sysfs_hotplug_event] generating hotplug event
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-09 2:06 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-09 2:06 UTC (permalink / raw)
To: robdclark-Re5JQEeQqe8AvxtiuMwx3w, sean-p7yTbzM4H96eqtR555YLDQ,
dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
freedreno-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW, airlied-cv59FeDIM0c,
daniel-/w4YWyX8dFk, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linus.walleij-QSEj5FYQhm4dnm+yROfE0A, jonathan-eSc4qw6YbEQ,
robh-DgEjT+Ai2ygdnm+yROfE0A
[-- Attachment #1: Type: text/plain, Size: 611 bytes --]
On Wed, May 08, 2019 at 10:03:46PM -0400, Brian Masney wrote:
> Here is a patch series that adds initial display support for the LG
> Nexus 5 (hammerhead) phone. It's not fully working so that's why some
> of these patches are RFC until we can get it fully working.
>
> The phones boots into terminal mode, however there is a several second
> (or more) delay when writing to tty1 compared to when the changes are
> actually shown on the screen. The following errors are in dmesg:
I attached the full dmesg output with this patch series applied. I
enabled debugging messages for just the DRM subsystem.
Brian
[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 86515 bytes --]
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty (masneyb@ins7386) (gcc version 8.1.1 20180626 (Red Hat Cross 8.1.1-3) (GCC)) #303 SMP PREEMPT Wed May 8 21:59:17 EDT 2019
[ 0.000000] CPU: ARMv7 Processor [512f06f0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: LGE MSM 8974 HAMMERHEAD
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 256 MiB at 0x20000000
[ 0.000000] On node 0 totalpages: 491776
[ 0.000000] Normal zone: 1536 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 164096 pages, LIFO batch:31
[ 0.000000] HighMem zone: 327680 pages, LIFO batch:63
[ 0.000000] percpu: Embedded 17 pages/cpu s39756 r8192 d21684 u69632
[ 0.000000] pcpu-alloc: s39756 r8192 d21684 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 490240
[ 0.000000] Kernel command line: console=tty0 console=ttyMSM0,115200,n8 rootwait androidboot.hardware=hammerhead user_debug=31 maxcpus=2 msm_watchdog_v2.enable=1 PMOS_NO_OUTPUT_REDIRECT=1 uart_console=enable gpt=enable lge.kcal=0|0|0|x lge.rev=rev_11 androidboot.laf androidboot.emmc=true fastboot=true androidboot.serialno=019eef1708e40fd2 androidboot.bootloader=HHZ20h androidboot.baseband=msm androidboot.hardware.sku=D820 androidboot.hardware.ddr=hynix androidboot.hardware.display=orise androidboot.revision=11
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1633208K/1967104K available (8192K kernel code, 834K rwdata, 3436K rodata, 1024K init, 266K bss, 71752K reserved, 262144K cma-reserved, 1310720K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x300/0x490 with crng_init=0
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000017] Switching to timer-based delay loop, resolution 52ns
[ 0.000410] Console: colour dummy device 80x30
[ 0.000785] printk: console [tty0] enabled
[ 0.000823] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000854] pid_max: default: 32768 minimum: 301
[ 0.000984] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001014] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001504] *** VALIDATE proc ***
[ 0.001629] *** VALIDATE cgroup1 ***
[ 0.001651] *** VALIDATE cgroup2 ***
[ 0.001676] CPU: Testing write buffer coherency: ok
[ 0.001939] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.059943] Setting up static identity map for 0x300000 - 0x300060
[ 0.079942] rcu: Hierarchical SRCU implementation.
[ 0.120017] smp: Bringing up secondary CPUs ...
[ 0.200453] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.200671] smp: Brought up 1 node, 2 CPUs
[ 0.200705] SMP: Total of 2 processors activated (76.80 BogoMIPS).
[ 0.200725] CPU: All CPU(s) started in SVC mode.
[ 0.202148] devtmpfs: initialized
[ 0.211750] VFP support v0.3: implementor 51 architecture 64 part 6f variant 2 rev 0
[ 0.212072] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.212111] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.221586] pinctrl core: initialized pinctrl subsystem
[ 0.222779] NET: Registered protocol family 16
[ 0.224668] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.225901] cpuidle: using governor menu
[ 0.226527] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.226553] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.268095] vgaarb: loaded
[ 0.268597] SCSI subsystem initialized
[ 0.268816] libata version 3.00 loaded.
[ 0.269096] usbcore: registered new interface driver usbfs
[ 0.269185] usbcore: registered new interface driver hub
[ 0.269290] usbcore: registered new device driver usb
[ 0.270505] Advanced Linux Sound Architecture Driver Initialized.
[ 0.271640] clocksource: Switched to clocksource arch_sys_counter
[ 0.624778] NET: Registered protocol family 2
[ 0.625271] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.625313] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.625381] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.625472] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.625571] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.625610] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.625774] NET: Registered protocol family 1
[ 0.626294] RPC: Registered named UNIX socket transport module.
[ 0.626319] RPC: Registered udp transport module.
[ 0.626341] RPC: Registered tcp transport module.
[ 0.626363] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.626390] PCI: CLS 0 bytes, default 64
[ 0.626644] Trying to unpack rootfs image as initramfs...
[ 0.830413] Freeing initrd memory: 40224K
[ 0.831171] hw perfevents: enabled with armv7_krait PMU driver, 5 counters available
[ 0.833228] Initialise system trusted keyrings
[ 0.833427] workingset: timestamp_bits=30 max_order=19 bucket_order=0
[ 0.840496] NFS: Registering the id_resolver key type
[ 0.840532] Key type id_resolver registered
[ 0.840554] Key type id_legacy registered
[ 0.841204] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.841533] fuse: init (API version 7.30)
[ 0.841996] Key type asymmetric registered
[ 0.842019] Asymmetric key parser 'x509' registered
[ 0.842090] bounce: pool size: 64 pages
[ 0.842145] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.842172] io scheduler mq-deadline registered
[ 0.842195] io scheduler kyber registered
[ 0.865206] msm_serial f991d000.serial: msm_serial: detected port #0
[ 0.865268] msm_serial f991d000.serial: uartclk = 7372800
[ 0.865339] f991d000.serial: ttyMSM0 at MMIO 0xf991d000 (irq = 27, base_baud = 460800) is a MSM
[ 0.865386] msm_serial: console setup on port #0
[ 1.437147] printk: console [ttyMSM0] enabled
[ 1.442335] msm_serial: driver initialized
[ 1.446406] [drm:drm_core_init] Initialized
[ 1.450208] [drm:msm_drm_register] init
[ 1.454316] [drm:msm_mdp_register]
[ 1.458422] [drm:msm_dsi_register]
[ 1.461972] [drm:msm_edp_register]
[ 1.466480] [drm:mdp5_dev_probe]
[ 1.469612] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 1.472059] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 1.495818] brd: module loaded
[ 1.505768] loop: module loaded
[ 1.506371] SCSI Media Changer driver v0.25
[ 1.508855] spmi spmi-0: PMIC arbiter version v1 (0x20000002)
[ 1.521054] GPIO line 360 (otg-gpio) hogged as output/high
[ 1.526208] s1: supplied by regulator-dummy
[ 1.526582] s2: supplied by regulator-dummy
[ 1.529836] s3: supplied by regulator-dummy
[ 1.534087] s4: Bringing 5100000uV into 5000000-5000000uV
[ 1.538148] l1: supplied by regulator-dummy
[ 1.543792] l2: supplied by regulator-dummy
[ 1.547731] l3: supplied by regulator-dummy
[ 1.551921] l4: supplied by regulator-dummy
[ 1.556056] l5: supplied by regulator-dummy
[ 1.560244] l6: supplied by regulator-dummy
[ 1.564423] l7: supplied by regulator-dummy
[ 1.568574] l8: supplied by regulator-dummy
[ 1.572765] l9: supplied by regulator-dummy
[ 1.576904] l10: supplied by regulator-dummy
[ 1.581084] l11: supplied by regulator-dummy
[ 1.585616] l12: supplied by regulator-dummy
[ 1.589867] l13: supplied by regulator-dummy
[ 1.594118] l14: supplied by regulator-dummy
[ 1.598358] l15: supplied by regulator-dummy
[ 1.602654] l16: supplied by regulator-dummy
[ 1.606863] l17: supplied by regulator-dummy
[ 1.611131] l18: supplied by regulator-dummy
[ 1.615392] l19: supplied by regulator-dummy
[ 1.619644] l20: supplied by regulator-dummy
[ 1.623921] l21: supplied by regulator-dummy
[ 1.628145] l22: supplied by regulator-dummy
[ 1.632434] l23: supplied by regulator-dummy
[ 1.636651] l24: supplied by regulator-dummy
[ 1.640922] lvs1: supplied by regulator-dummy
[ 1.645125] lvs2: supplied by regulator-dummy
[ 1.649354] lvs3: supplied by regulator-dummy
[ 1.653899] 5vs1: supplied by s4
[ 1.658101] 5vs2: supplied by s4
[ 1.662570] libphy: Fixed MDIO Bus: probed
[ 1.664506] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 1.668154] CSLIP: code copyright 1989 Regents of the University of California.
[ 1.677881] usbcore: registered new interface driver ax88179_178a
[ 1.685059] usbcore: registered new interface driver cdc_ether
[ 1.691285] usbcore: registered new interface driver net1080
[ 1.697033] usbcore: registered new interface driver cdc_subset
[ 1.702884] usbcore: registered new interface driver cdc_ncm
[ 1.708638] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.714366] ehci-pci: EHCI PCI platform driver
[ 1.720772] usbcore: registered new interface driver cdc_acm
[ 1.725110] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.746239] rtc-pm8xxx fc4cf000.spmi:pm8941@0:rtc@6000: registered as rtc0
[ 1.746476] i2c /dev entries driver
[ 1.752325] i2c_qup f9923000.i2c:
tx channel not available
[ 1.756240] i2c_qup f9925000.i2c:
tx channel not available
[ 1.770247] lm3630a_bl 2-0038: LM3630A backlight register OK.
[ 1.770594] i2c_qup f9968000.i2c:
tx channel not available
[ 1.776699] qcom-smbb fc4cf000.spmi:pm8941@0:charger@1000: Initializing SMBB rev 3
[ 1.786344] otg-vbus: supplied by 5vs1
[ 1.790745] qcom-tsens fc4a9000.thermal-sensor: tsens calibration failed
[ 1.794029] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations
[ 1.800615] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations
[ 1.807900] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations
[ 1.814941] cpuidle: enable-method property 'qcom,kpss-acc-v2' found operations
[ 1.822673] sdhci: Secure Digital Host Controller Interface driver
[ 1.829350] sdhci: Copyright(c) Pierre Ossman
[ 1.835628] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.842527] usbcore: registered new interface driver usbhid
[ 1.845757] usbhid: USB HID core driver
[ 1.854207] oprofile: using timer interrupt.
[ 1.855073] NET: Registered protocol family 17
[ 1.859449] Key type dns_resolver registered
[ 1.864071] Registering SWP/SWPB emulation handler
[ 1.868651] Loading compiled-in X.509 certificates
[ 1.903305] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 1.903386] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 1.931752] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 1.931862] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 1.954303] s1: supplied by regulator-dummy
[ 1.954396] s1: Bringing 0uV into 675000-675000uV
[ 1.961140] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 1.962969] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 1.974984] s2: supplied by regulator-dummy
[ 1.986512] s2: Bringing 0uV into 500000-500000uV
[ 1.990426] s3: supplied by regulator-dummy
[ 1.995072] s3: Bringing 0uV into 1050000-1050000uV
[ 1.999485] s4: supplied by regulator-dummy
[ 2.003931] s4: Bringing 0uV into 815000-815000uV
[ 2.008301] s5: supplied by regulator-dummy
[ 2.013266] s6: supplied by regulator-dummy
[ 2.017204] s7: supplied by regulator-dummy
[ 2.021371] s8: supplied by regulator-dummy
[ 2.025952] s1: supplied by regulator-dummy
[ 2.029413] s1: Bringing 0uV into 1300000-1300000uV
[ 2.036531] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 2.038422] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 2.050730] s2: supplied by regulator-dummy
[ 2.062206] s2: Bringing 0uV into 2150000-2150000uV
[ 2.066310] s3: supplied by regulator-dummy
[ 2.070734] s3: Bringing 0uV into 1800000-1800000uV
[ 2.076623] input: soc:gpio-keys as /devices/platform/soc/soc:gpio-keys/input/input0
[ 2.080214] rtc-pm8xxx fc4cf000.spmi:pm8941@0:rtc@6000: setting system clock to 1970-01-25T07:16:55 UTC (2099815)
[ 2.089736] wl-reg: disabling
[ 2.090219] l1: supplied by s1
[ 2.098016] ALSA device list:
[ 2.100860] l1: Bringing 0uV into 1225000-1225000uV
[ 2.103779] No soundcards found.
[ 2.107214] l2: supplied by s3
[ 2.115377] l2: Bringing 0uV into 1200000-1200000uV
[ 2.115928] l3: supplied by s1
[ 2.116580] Freeing unused kernel memory: 1024K
[ 2.119130] l3: Bringing 0uV into 1225000-1225000uV
[ 2.126986] l4: supplied by s1
[ 2.134682] l4: Bringing 0uV into 1225000-1225000uV
[ 2.137938] l5: supplied by s2
[ 2.142596] l5: Bringing 0uV into 1800000-1800000uV
[ 2.145923] l6: supplied by s2
[ 2.150452] l6: Bringing 0uV into 1800000-1800000uV
[ 2.154552] l7: supplied by s2
[ 2.158357] l7: Bringing 0uV into 1800000-1800000uV
[ 2.161841] l8: supplied by vph-pwr
[ 2.166248] l8: Bringing 0uV into 1800000-1800000uV
[ 2.170238] l9: supplied by vreg-boost
[ 2.174715] Run /init as init process
[ 2.174780] l9: Bringing 0uV into 1800000-1800000uV
[ 2.182142] mmc0: SDHCI controller on f98a4900.sdhci [f98a4900.sdhci] using ADMA
[ 2.187703] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_regulator_init: failed to init regulator, ret=-517
[ 2.194818] l10: supplied by vreg-boost
[ 2.206363] msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR* dsi_phy_driver_probe: failed to init regulator
[ 2.210753] l10: Bringing 0uV into 1800000-1800000uV
[ 2.221617] l11: supplied by s1
[ 2.230312] l11: Bringing 0uV into 1300000-1300000uV
[ 2.235025] l12: supplied by s2
[ 2.239432] l12: Bringing 0uV into 1800000-1800000uV
[ 2.242907] l13: supplied by vreg-boost
[ 2.247724] l13: Bringing 0uV into 1800000-1800000uV
[ 2.251575] l14: supplied by s2
[ 2.256385] l14: Bringing 0uV into 1800000-1800000uV
[ 2.259634] l15: supplied by s2
[ 2.264420] l15: Bringing 0uV into 2050000-2050000uV
[ 2.267535] l16: supplied by vph-pwr
[ 2.272518] l16: Bringing 0uV into 2700000-2700000uV
[ 2.276242] l17: supplied by vreg-boost
[ 2.280917] l17: Bringing 0uV into 2850000-2850000uV
[ 2.284949] l18: supplied by vph-pwr
[ 2.289734] l18: Bringing 0uV into 2850000-2850000uV
[ 2.293620] l19: supplied by vph-pwr
[ 2.298259] l19: Bringing 0uV into 3000000-3000000uV
[ 2.302203] l20: supplied by vreg-boost
[ 2.306749] l20: Bringing 0uV into 2950000-2950000uV
[ 2.310787] l21: supplied by vreg-boost
[ 2.315548] l21: Bringing 0uV into 2950000-2950000uV
[ 2.319567] l22: supplied by vreg-boost
[ 2.324319] l22: Bringing 0uV into 3000000-3000000uV
[ 2.328183] l23: supplied by vreg-boost
[ 2.333080] l23: Bringing 0uV into 3000000-3000000uV
[ 2.336953] l24: supplied by vreg-boost
[ 2.341876] l24: Bringing 0uV into 3075000-3075000uV
[ 2.346008] lvs1: supplied by s3
[ 2.350968] lvs2: supplied by s3
[ 2.354222] lvs3: supplied by s3
[ 2.357474] 5vs1: supplied by regulator-dummy
[ 2.360653] 5vs2: supplied by regulator-dummy
[ 2.367752] random: fast init done
[ 2.371038] mmc0: new ultra high speed SDR104 SDIO card at address 0001
[ 2.373113] [drm:pll_28nm_register] 0
[ 2.378626] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_dc_off = 9
[ 2.382375] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_freq_seed = 31289
[ 2.388077] [drm:dsi_pll_28nm_clk_recalc_rate] vco rate = 402333398
[ 2.394525] [drm:dsi_pll_28nm_clk_recalc_rate] returning vco rate = 402333398
[ 2.401711] [drm:msm_dsi_pll_init] DSI:0 PLL registered
[ 2.448289] mmc1: SDHCI controller on f9824900.sdhci [f9824900.sdhci] using ADMA
[ 2.448730] [drm:mdp5_mdss_init]
[ 2.455563] [drm:mdp5_bind]
[ 2.458257] [drm:get_clk] skipping lut
[ 2.461016] [drm:msm_runtime_resume]
[ 2.464538] [drm:mdp5_mdss_enable]
[ 2.468324] [drm:mdp5_runtime_resume]
[ 2.471553] [drm:mdp5_enable]
[ 2.475559] [drm:mdp5_runtime_suspend]
[ 2.478538] [drm:mdp5_disable]
[ 2.482321] msm_mdp fd900100.mdp: [drm:mdp5_bind] MDP5 version v1.2
[ 2.485404] [drm:mdp5_cfg_init] MDP5: msm8x74 hw config selected
[ 2.491686] [drm:mdp5_ctlm_init] Pool of 5 CTLs created.
[ 2.497932] msm fd900000.mdss: bound fd900100.mdp (ops mdp5_ops)
[ 2.503229] [drm:dsi_bind]
[ 2.509184] [drm:dsi_bind] dsi probed=(ptrval)
[ 2.511936] msm_dsi fd922800.dsi: fd922800.dsi supply gdsc not found, using dummy regulator
[ 2.516320] [drm:msm_dsi_host_init] dsi_get_config: Version 3:10010000
[ 2.524587] msm_dsi fd922800.dsi: fd922800.dsi supply gdsc not found, using dummy regulator
[ 2.532920] [drm:msm_dsi_host_init] Dsi Host 0 initialized
[ 2.540829] [drm:msm_dsi_runtime_resume] id=0
[ 2.546386] panel-simple-dsi fd922800.dsi.0: fd922800.dsi.0 supply power not found, using dummy regulator
[ 2.550819] [drm:dsi_host_attach] id=0
[ 2.560278] msm fd900000.mdss: bound fd922800.dsi (ops dsi_ops)
[ 2.563869] [drm] using 16m VRAM carveout
[ 2.569691] [drm:msm_dsi_runtime_suspend]
[ 2.579129] msm fd900000.mdss: [drm:msm_drm_bind] VRAM: 20100000->21100000
[ 2.579284] [drm:mdp5_runtime_resume]
[ 2.584944] [drm:mdp5_enable]
[ 2.595290] mmc1: new HS200 MMC card at address 0001
[ 2.596083] mmcblk1: mmc1:0001 SEM16G 14.7 GiB
[ 2.599616] mmcblk1boot0: mmc1:0001 SEM16G partition 1 4.00 MiB
[ 2.611955] mmcblk1boot1: mmc1:0001 SEM16G partition 2 4.00 MiB
[ 2.612178] mmcblk1rpmb: mmc1:0001 SEM16G partition 3 4.00 MiB, chardev (247:0)
[ 2.617161] msm_mdp fd900100.mdp: [drm:mdp5_kms_init] no iommu, fallback to phys contig buffers for scanout
[ 2.624150] [drm:mdp5_runtime_suspend]
[ 2.633911] [drm:mdp5_disable]
[ 2.637722] msm fd900000.mdss: fall back to the other CTL category for INTF 1!
[ 2.640653] [drm:mdp5_ctlm_request] CTL 0 allocated
[ 2.648547] [drm:mdp5_runtime_resume]
[ 2.653040] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29
[ 2.659516] [drm:mdp5_enable]
[ 2.672935] [drm:mdp5_runtime_suspend]
[ 2.672969] [drm:mdp5_disable]
[ 2.675763] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.678704] [drm] Driver supports precise vblank timestamp query.
[ 2.685346] [drm:drm_irq_install] irq=78
[ 2.691558] [drm:mdp5_runtime_resume]
[ 2.695572] [drm:mdp5_enable]
[ 2.699132] [drm:mdp5_runtime_suspend]
[ 2.702167] [drm:mdp5_disable]
[ 2.705932] [drm:mdp5_runtime_resume]
[ 2.708996] [drm:mdp5_enable]
[ 2.712878] [drm:mdp5_runtime_suspend]
[ 2.715855] [drm:mdp5_disable]
[ 2.719602] [drm:drm_minor_register]
[ 2.723028] [drm:drm_minor_register] new minor registered 128
[ 2.726537] [drm:drm_minor_register]
[ 2.732556] [drm:drm_minor_register] new minor registered 0
[ 2.736029] [drm:drm_sysfs_connector_add] adding "DSI-1" to sysfs
[ 2.741296] [drm:drm_sysfs_hotplug_event] generating hotplug event
[ 2.747642] [drm] Initialized msm 1.5.0 20130625 for fd900000.mdss on minor 0
[ 2.753657] [drm:drm_mode_object_get] OBJ ID: 31 (2)
[ 2.760825] [drm:drm_setup_crtcs]
[ 2.765883] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:31:DSI-1]
[ 2.769079] [drm:dsi_mgr_connector_detect] id=0
[ 2.776303] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:31:DSI-1] status updated from unknown to connected
[ 2.780725] [drm:dsi_mgr_connector_mode_valid]
[ 2.791490] [drm:dsi_mgr_connector_mode_valid] requested=150000000, actual=150000000
[ 2.796056] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:31:DSI-1] probed modes :
[ 2.804007] [drm:drm_mode_debug_printmodeline] Modeline "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0
[ 2.812427] [drm:drm_setup_crtcs] connector 31 enabled? yes
[ 2.823697] [drm:drm_setup_crtcs] Not using firmware configuration
[ 2.829233] [drm:drm_setup_crtcs] looking for cmdline mode on connector 31
[ 2.835510] [drm:drm_setup_crtcs] looking for preferred mode on connector 31 0
[ 2.842363] [drm:drm_setup_crtcs] found mode 1080x1920
[ 2.849539] [drm:drm_setup_crtcs] picking CRTCs for 65535x65535 config
[ 2.854690] [drm:drm_setup_crtcs] desired mode 1080x1920 set on crtc 49 (0,0)
[ 2.861197] [drm:drm_mode_object_get] OBJ ID: 31 (2)
[ 2.868418] [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
[ 2.873457] [drm:msm_fbdev_create] create fbdev: 1080x1920@32 (1080x1920)
[ 2.881142] [drm:msm_alloc_stolen_fb] allocating 8355840 bytes for fb 0
[ 2.888552] [drm:msm_framebuffer_init] create framebuffer: dev=(ptrval), mode_cmd=(ptrval) (1080x1920@XR24)
[ 2.894379] [drm:msm_framebuffer_init] create: FB ID: 50 ((ptrval))
[ 2.904088] [drm:msm_fbdev_create] fbi=(ptrval), dev=(ptrval)
[ 2.910401] [drm:msm_fbdev_create] par=(ptrval), 1080x1920
[ 2.916232] [drm:msm_fbdev_create] allocated 1080x1920 fb
[ 2.922042] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 2.922064] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 2.922081] [drm:drm_atomic_get_plane_state] Added [PLANE:35:plane-1] (ptrval) state to (ptrval)
[ 2.922095] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:35:plane-1] state (ptrval)
[ 2.922112] [drm:drm_atomic_get_plane_state] Added [PLANE:37:plane-2] (ptrval) state to (ptrval)
[ 2.922125] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:37:plane-2] state (ptrval)
[ 2.922142] [drm:drm_atomic_get_plane_state] Added [PLANE:39:plane-3] (ptrval) state to (ptrval)
[ 2.922154] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:39:plane-3] state (ptrval)
[ 2.922170] [drm:drm_atomic_get_plane_state] Added [PLANE:41:plane-4] (ptrval) state to (ptrval)
[ 2.922183] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:41:plane-4] state (ptrval)
[ 2.922199] [drm:drm_atomic_get_plane_state] Added [PLANE:43:plane-5] (ptrval) state to (ptrval)
[ 2.922212] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:43:plane-5] state (ptrval)
[ 2.922228] [drm:drm_atomic_get_plane_state] Added [PLANE:45:plane-6] (ptrval) state to (ptrval)
[ 2.922241] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:45:plane-6] state (ptrval)
[ 2.922257] [drm:drm_atomic_get_plane_state] Added [PLANE:47:plane-7] (ptrval) state to (ptrval)
[ 2.922270] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:47:plane-7] state (ptrval)
[ 2.922288] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 2.922308] [drm:drm_atomic_set_mode_for_crtc] Set [MODE:1080x1920] for [CRTC:49:crtc-0] state (ptrval)
[ 2.922325] [drm:drm_atomic_set_crtc_for_plane] Link [PLANE:32:plane-0] state (ptrval) to [CRTC:49:crtc-0]
[ 2.922339] [drm:drm_atomic_set_fb_for_plane] Set [FB:50] for [PLANE:32:plane-0] state (ptrval)
[ 2.922350] [drm:drm_mode_object_get] OBJ ID: 50 (1)
[ 2.922368] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval)
[ 2.922384] [drm:drm_mode_object_get] OBJ ID: 31 (3)
[ 2.922399] [drm:drm_atomic_get_connector_state] Added [CONNECTOR:31:DSI-1] (ptrval) state to (ptrval)
[ 2.922410] [drm:drm_mode_object_get] OBJ ID: 31 (4)
[ 2.922427] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [CRTC:49:crtc-0]
[ 2.922439] [drm:drm_atomic_check_only] checking (ptrval)
[ 2.922460] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] mode changed
[ 2.922473] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] enable changed
[ 2.922486] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] active changed
[ 2.922497] [drm:dsi_mgr_connector_best_encoder]
[ 2.922513] [drm:drm_atomic_helper_check_modeset] Updating routing for [CONNECTOR:31:DSI-1]
[ 2.922523] [drm:dsi_mgr_connector_best_encoder]
[ 2.922544] [drm:drm_atomic_helper_check_modeset] [CONNECTOR:31:DSI-1] using [ENCODER:30:DSI-30] on [CRTC:49:crtc-0]
[ 2.922559] [drm:drm_atomic_helper_check_modeset] [CRTC:49:crtc-0] needs all connectors, enable: y, active: y
[ 2.922575] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval)
[ 2.922593] [drm:drm_atomic_add_affected_planes] Adding all current planes for [CRTC:49:crtc-0] to (ptrval)
[ 2.922610] [drm:drm_atomic_normalize_zpos] [CRTC:49:crtc-0] calculating normalized zpos values
[ 2.922625] [drm:drm_atomic_normalize_zpos] [PLANE:32:plane-0] processing zpos value 0
[ 2.922639] [drm:drm_atomic_normalize_zpos] [PLANE:32:plane-0] normalized zpos value 0
[ 2.922654] [drm:mdp5_plane_atomic_check] plane-0: check (0 -> 0)
[ 2.922678] [drm:drm_atomic_get_private_obj_state] Added new private object (ptrval) state (ptrval) to (ptrval)
[ 2.922694] [drm:mdp5_pipe_assign] DMA0: alloc SMP blocks
[ 2.922708] [drm:mdp5_smp_assign] DMA0[0]: request 3 SMP blocks
[ 2.922724] [drm:mdp5_pipe_assign] DMA0: assign to plane plane-0 for caps 0
[ 2.922740] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 2.922755] [drm:mdp5_mixer_assign] assigning Layer Mixer 0 to crtc crtc-0
[ 2.922772] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 2.922785] [drm:drm_atomic_commit] committing (ptrval)
[ 2.922806] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 2.922828] [drm:mdp5_runtime_resume]
[ 2.922839] [drm:mdp5_enable]
[ 2.922884] [drm:mdp5_smp_prepare_commit] assign DMA0:0, 3 blks
[ 2.922896] [drm:mdp5_smp_prepare_commit] assign DMA0:1, 3 blks
[ 2.922908] [drm:mdp5_smp_prepare_commit] assign DMA0:2, 3 blks
[ 2.922951] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 2.922964] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 2.922980] [drm:drm_atomic_helper_commit_modeset_disables] modeset on [CRTC:49:crtc-0]
[ 2.923000] [drm:mdp5_crtc_mode_set_nofb] crtc-0: set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0
[ 2.923018] [drm:drm_atomic_helper_commit_modeset_disables] modeset on [ENCODER:30:DSI-30]
[ 2.923036] [drm:dsi_mgr_bridge_mode_set] set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0
[ 2.923050] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 2.923062] [drm:mdp5_plane_atomic_update] plane-0: update
[ 2.923078] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 2.923090] [drm:mdp5_plane_mode_set] scale config = 0
[ 2.923117] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 2.923146] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 2.923161] [drm:crtc_flush] crtc-0: flush=00000840
[ 2.923179] [drm:drm_atomic_helper_commit_modeset_enables] enabling [CRTC:49:crtc-0]
[ 2.923192] [drm:mdp5_crtc_atomic_enable] crtc-0
[ 2.923210] [drm:drm_crtc_vblank_on] crtc 0, vblank enabled 0, inmodeset 0
[ 2.923238] [drm:mdp5_crtc_mode_set_nofb] crtc-0: set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0
[ 2.923260] [drm:drm_atomic_helper_commit_modeset_enables] enabling [ENCODER:30:DSI-30]
[ 2.923272] [drm:dsi_mgr_bridge_pre_enable] id=0
[ 2.923282] [drm:msm_dsi_host_reset_phy]
[ 2.927146] [drm:dsi_calc_clk_rate_6g] pclk=150000000, bclk=112500000
[ 2.927161] [drm:msm_dsi_phy_enable]
[ 2.927366] [drm:dsi_28nm_phy_enable]
[ 2.927384] [drm:msm_dsi_dphy_timing_calc] PHY timings: 44, 2, 0, 238, 56, 38, 106, 108, 44, 60, 44
[ 2.927428] [drm:msm_dsi_host_power_on]
[ 2.928075] [drm:msm_dsi_runtime_resume] id=0
[ 2.928101] [drm:dsi_link_clk_enable_6g] Set clk rates: pclk=150000, byteclk=112500000
[ 2.928170] [drm:dsi_pll_28nm_clk_set_rate] refclk_cfg = 1
[ 2.928182] [drm:dsi_pll_28nm_clk_set_rate] div_fb = 11718
[ 2.928193] [drm:dsi_pll_28nm_clk_set_rate] frac_n_value = 47054
[ 2.928204] [drm:dsi_pll_28nm_clk_set_rate] Generated VCO Clock: 449971200
[ 2.928215] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg0=0
[ 2.928226] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg1=74
[ 2.928237] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg2=206
[ 2.928248] [drm:dsi_pll_28nm_clk_set_rate] sdm_cfg3=183
[ 2.928260] [drm:dsi_pll_28nm_clk_set_rate] cal_cfg10=193, cal_cfg11=1
[ 2.928285] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_dc_off = 10
[ 2.928297] [drm:dsi_pll_28nm_clk_recalc_rate] sdm_freq_seed = 47054
[ 2.928308] [drm:dsi_pll_28nm_clk_recalc_rate] vco rate = 449970703
[ 2.928320] [drm:dsi_pll_28nm_clk_recalc_rate] returning vco rate = 449970703
[ 2.928394] [drm:dsi_pll_28nm_enable_seq_hpm] id=0
[ 2.930017] [drm:pll_28nm_poll_for_ready] DSI PLL is locked
[ 2.930027] [drm:dsi_pll_28nm_enable_seq_hpm] DSI PLL Lock success
[ 2.930040] [drm:msm_dsi_pll_helper_clk_prepare] DSI PLL locked after sequence #1
[ 2.930061] [drm:msm_dsi_host_power_on]
[ 2.930078] [drm:dsi_intr_ctrl] intr=2000000 enable=1
[ 2.930090] [drm:msm_dsi_host_power_on] lane number=4
[ 2.930107] [drm:dsi_intr_ctrl] intr=2000200 enable=1
[ 2.930126] [drm:mdp5_cmd_encoder_mode_set] set mode: "1080x1920": 60 150000 1080 1082 1084 1086 1920 1922 1924 1926 0x48 0x0
[ 2.930157] [drm:mdp5_crtc_vblank_irq] crtc-0: send event: (ptrval)
[ 2.930199] [drm:mdp5_ctl_set_encoder_state] intf_1: on
[ 2.930214] [drm:drm_bridge_enable]
[ 2.930227] [drm:msm_enable_vblank] dev=(ptrval), crtc=0
[ 2.930247] [drm:drm_vblank_enable] enabling vblank on crtc 0, ret: 0
[ 2.930266] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 2.981842] msm fd900000.mdss: pp done time out, lm=0
[ 3.041732] ------------[ cut here ]------------
[ 3.041751] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 3.041759] [CRTC:49:crtc-0] vblank wait timed out
[ 3.041764] Modules linked in:
[ 3.041784] CPU: 0 PID: 100 Comm: kworker/0:2 Not tainted 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 3.041792] Hardware name: Generic DT based system
[ 3.041812] Workqueue: events deferred_probe_work_func
[ 3.041839] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 3.041853] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 3.041871] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 3.041884] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 3.041899] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 3.041916] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 3.041937] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 3.041952] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 3.041963] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 3.041973] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4)
[ 3.041985] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c076a7d0>] (drm_fb_helper_restore_fbdev_mode_unlocked+0x54/0xa4)
[ 3.041996] [<c076a7d0>] (drm_fb_helper_restore_fbdev_mode_unlocked) from [<c076a850>] (drm_fb_helper_set_par+0x30/0x54)
[ 3.042007] [<c076a850>] (drm_fb_helper_set_par) from [<c06ef4c8>] (fbcon_init+0x4b4/0x5d4)
[ 3.042019] [<c06ef4c8>] (fbcon_init) from [<c073bf88>] (visual_init+0xbc/0x104)
[ 3.042030] [<c073bf88>] (visual_init) from [<c073dea8>] (do_bind_con_driver+0x1ec/0x3c4)
[ 3.042040] [<c073dea8>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0)
[ 3.042050] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8)
[ 3.042066] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80)
[ 3.042078] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68)
[ 3.042094] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304)
[ 3.042106] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c)
[ 3.042120] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc)
[ 3.042131] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634)
[ 3.042146] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4)
[ 3.042160] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174)
[ 3.042175] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98)
[ 3.042188] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c)
[ 3.042200] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0)
[ 3.042211] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4)
[ 3.042222] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168)
[ 3.042232] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c)
[ 3.042243] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4)
[ 3.042259] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 3.042273] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 3.042285] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 3.042297] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 3.042306] Exception stack(0xc4e09fb0 to 0xc4e09ff8)
[ 3.042325] 9fa0: 00000000 00000000 00000000 00000000
[ 3.042350] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 3.042371] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 3.042380] ---[ end trace d4b922f6bb6a2602 ]---
[ 3.042416] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 3.042430] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (5)
[ 3.042451] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 3.042514] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 3.042528] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 3.042543] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 3.042556] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 3.042571] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 3.042588] [drm:drm_atomic_get_plane_state] Added [PLANE:35:plane-1] (ptrval) state to (ptrval)
[ 3.042601] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:35:plane-1] state (ptrval)
[ 3.042617] [drm:drm_atomic_get_plane_state] Added [PLANE:37:plane-2] (ptrval) state to (ptrval)
[ 3.042630] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:37:plane-2] state (ptrval)
[ 3.042646] [drm:drm_atomic_get_plane_state] Added [PLANE:39:plane-3] (ptrval) state to (ptrval)
[ 3.042659] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:39:plane-3] state (ptrval)
[ 3.042675] [drm:drm_atomic_get_plane_state] Added [PLANE:41:plane-4] (ptrval) state to (ptrval)
[ 3.042687] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:41:plane-4] state (ptrval)
[ 3.042703] [drm:drm_atomic_get_plane_state] Added [PLANE:43:plane-5] (ptrval) state to (ptrval)
[ 3.042716] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:43:plane-5] state (ptrval)
[ 3.042732] [drm:drm_atomic_get_plane_state] Added [PLANE:45:plane-6] (ptrval) state to (ptrval)
[ 3.042745] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:45:plane-6] state (ptrval)
[ 3.042761] [drm:drm_atomic_get_plane_state] Added [PLANE:47:plane-7] (ptrval) state to (ptrval)
[ 3.042774] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:47:plane-7] state (ptrval)
[ 3.042789] [drm:drm_atomic_set_fb_for_plane] Set [FB:50] for [PLANE:32:plane-0] state (ptrval)
[ 3.042800] [drm:drm_mode_object_get] OBJ ID: 50 (3)
[ 3.042812] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (4)
[ 3.042828] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval)
[ 3.042843] [drm:drm_mode_object_get] OBJ ID: 31 (5)
[ 3.042854] [drm:drm_mode_object_get] OBJ ID: 31 (6)
[ 3.042869] [drm:drm_atomic_get_connector_state] Added [CONNECTOR:31:DSI-1] (ptrval) state to (ptrval)
[ 3.042882] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6)
[ 3.042896] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [NOCRTC]
[ 3.042907] [drm:drm_mode_object_get] OBJ ID: 31 (5)
[ 3.042924] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [CRTC:49:crtc-0]
[ 3.042936] [drm:drm_atomic_check_only] checking (ptrval)
[ 3.042949] [drm:dsi_mgr_connector_best_encoder]
[ 3.042967] [drm:drm_atomic_helper_check_modeset] Updating routing for [CONNECTOR:31:DSI-1]
[ 3.042976] [drm:dsi_mgr_connector_best_encoder]
[ 3.042996] [drm:drm_atomic_helper_check_modeset] [CONNECTOR:31:DSI-1] keeps [ENCODER:30:DSI-30], now on [CRTC:49:crtc-0]
[ 3.043012] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 3.043031] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 3.043047] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 3.043060] [drm:drm_atomic_commit] committing (ptrval)
[ 3.043078] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 3.043135] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 3.043148] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 3.043162] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 3.043173] [drm:mdp5_plane_atomic_update] plane-0: update
[ 3.043188] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 3.043199] [drm:mdp5_plane_mode_set] scale config = 0
[ 3.043223] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 3.043249] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 3.043263] [drm:crtc_flush] crtc-0: flush=00000840
[ 3.043304] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 3.101745] msm fd900000.mdss: pp done time out, lm=0
[ 3.161729] ------------[ cut here ]------------
[ 3.161746] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 3.161754] [CRTC:49:crtc-0] vblank wait timed out
[ 3.161758] Modules linked in:
[ 3.161778] CPU: 0 PID: 100 Comm: kworker/0:2 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 3.161786] Hardware name: Generic DT based system
[ 3.161803] Workqueue: events deferred_probe_work_func
[ 3.161820] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 3.161831] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 3.161844] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 3.161856] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 3.161870] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 3.161885] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 3.161900] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 3.161914] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 3.161926] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 3.161936] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4)
[ 3.161945] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c0766c48>] (drm_fb_helper_pan_display+0xc4/0x1d8)
[ 3.161957] [<c0766c48>] (drm_fb_helper_pan_display) from [<c06e7c38>] (fb_pan_display+0x9c/0x110)
[ 3.161969] [<c06e7c38>] (fb_pan_display) from [<c06f3528>] (bit_update_start+0x14/0x30)
[ 3.161979] [<c06f3528>] (bit_update_start) from [<c06f215c>] (fbcon_switch+0x390/0x514)
[ 3.161989] [<c06f215c>] (fbcon_switch) from [<c073d5d4>] (redraw_screen+0x13c/0x244)
[ 3.161999] [<c073d5d4>] (redraw_screen) from [<c06eef84>] (fbcon_prepare_logo+0x378/0x408)
[ 3.162007] [<c06eef84>] (fbcon_prepare_logo) from [<c06ef438>] (fbcon_init+0x424/0x5d4)
[ 3.162016] [<c06ef438>] (fbcon_init) from [<c073bf88>] (visual_init+0xbc/0x104)
[ 3.162025] [<c073bf88>] (visual_init) from [<c073dea8>] (do_bind_con_driver+0x1ec/0x3c4)
[ 3.162035] [<c073dea8>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0)
[ 3.162044] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8)
[ 3.162057] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80)
[ 3.162067] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68)
[ 3.162079] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304)
[ 3.162091] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c)
[ 3.162105] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc)
[ 3.162116] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634)
[ 3.162129] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4)
[ 3.162142] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174)
[ 3.162155] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98)
[ 3.162167] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c)
[ 3.162178] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0)
[ 3.162189] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4)
[ 3.162199] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168)
[ 3.162210] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c)
[ 3.162220] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4)
[ 3.162233] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 3.162246] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 3.162258] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 3.162268] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 3.162277] Exception stack(0xc4e09fb0 to 0xc4e09ff8)
[ 3.162295] 9fa0: 00000000 00000000 00000000 00000000
[ 3.162319] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 3.162340] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 3.162349] ---[ end trace d4b922f6bb6a2603 ]---
[ 3.162379] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50]
[ 3.162397] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 3.162409] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6)
[ 3.162421] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (5)
[ 3.162433] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2)
[ 3.162446] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3)
[ 3.162461] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 3.162491] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 3.162507] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 3.162519] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 3.162535] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 3.162545] [drm:drm_mode_object_get] OBJ ID: 52 (1)
[ 3.162558] [drm:drm_atomic_check_only] checking (ptrval)
[ 3.162575] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 3.162592] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 3.162609] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 3.162622] [drm:drm_atomic_commit] committing (ptrval)
[ 3.162638] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 3.581980] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org
[ 4.109986] EXT4-fs (dm-0): mounted filesystem without journal. Opts: (null)
[ 4.618939] [drm:mdp5_crtc_vblank_irq] crtc-0: send event: (ptrval)
[ 4.618983] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 4.618998] [drm:vblank_disable_fn] disabling vblank on crtc 0
[ 4.619016] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 4.619029] [drm:msm_disable_vblank] dev=(ptrval), crtc=0
[ 4.619112] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 4.619126] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 4.619142] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 4.619156] [drm:mdp5_plane_atomic_update] plane-0: update
[ 4.619173] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 4.619185] [drm:mdp5_plane_mode_set] scale config = 0
[ 4.619212] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 4.619243] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 4.619257] [drm:crtc_flush] crtc-0: flush=00000840
[ 4.619277] [drm:msm_enable_vblank] dev=(ptrval), crtc=0
[ 4.619293] [drm:drm_vblank_enable] enabling vblank on crtc 0, ret: 0
[ 4.619311] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 4.620660] [drm:dsi_host_irq] isr=0x2000700, id=0
[ 4.671711] msm fd900000.mdss: pp done time out, lm=0
[ 4.731689] ------------[ cut here ]------------
[ 4.731716] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 4.731724] [CRTC:49:crtc-0] vblank wait timed out
[ 4.731729] Modules linked in: dm_mod
[ 4.731757] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 4.731765] Hardware name: Generic DT based system
[ 4.731782] Workqueue: events drm_fb_helper_dirty_work
[ 4.731806] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 4.731820] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 4.731837] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 4.731849] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 4.731864] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 4.731885] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 4.731906] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 4.731921] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 4.731933] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 4.731948] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204)
[ 4.731960] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164)
[ 4.731975] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 4.731989] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 4.732002] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 4.732014] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 4.732023] Exception stack(0xde965fb0 to 0xde965ff8)
[ 4.732042] 5fa0: 00000000 00000000 00000000 00000000
[ 4.732067] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 4.732088] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 4.732106] ---[ end trace d4b922f6bb6a2604 ]---
[ 4.732142] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50]
[ 4.732160] [drm:drm_mode_object_put.part.0] OBJ ID: 52 (2)
[ 4.732179] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 4.732192] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2)
[ 4.732207] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3)
[ 4.732222] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 4.758491] Console: switching to colour frame buffer device 135x120
[ 4.758533] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 4.758548] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 4.758564] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 4.758578] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 4.758594] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 4.758612] [drm:drm_atomic_get_plane_state] Added [PLANE:35:plane-1] (ptrval) state to (ptrval)
[ 4.758626] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:35:plane-1] state (ptrval)
[ 4.758643] [drm:drm_atomic_get_plane_state] Added [PLANE:37:plane-2] (ptrval) state to (ptrval)
[ 4.758656] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:37:plane-2] state (ptrval)
[ 4.758673] [drm:drm_atomic_get_plane_state] Added [PLANE:39:plane-3] (ptrval) state to (ptrval)
[ 4.758686] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:39:plane-3] state (ptrval)
[ 4.758703] [drm:drm_atomic_get_plane_state] Added [PLANE:41:plane-4] (ptrval) state to (ptrval)
[ 4.758716] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:41:plane-4] state (ptrval)
[ 4.758733] [drm:drm_atomic_get_plane_state] Added [PLANE:43:plane-5] (ptrval) state to (ptrval)
[ 4.758746] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:43:plane-5] state (ptrval)
[ 4.758763] [drm:drm_atomic_get_plane_state] Added [PLANE:45:plane-6] (ptrval) state to (ptrval)
[ 4.758776] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:45:plane-6] state (ptrval)
[ 4.759026] [drm:drm_atomic_get_plane_state] Added [PLANE:47:plane-7] (ptrval) state to (ptrval)
[ 4.759040] [drm:drm_atomic_set_fb_for_plane] Set [NOFB] for [PLANE:47:plane-7] state (ptrval)
[ 4.759057] [drm:drm_atomic_set_fb_for_plane] Set [FB:50] for [PLANE:32:plane-0] state (ptrval)
[ 4.759069] [drm:drm_mode_object_get] OBJ ID: 50 (3)
[ 4.759080] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (4)
[ 4.759097] [drm:drm_atomic_add_affected_connectors] Adding all current connectors for [CRTC:49:crtc-0] to (ptrval)
[ 4.759114] [drm:drm_mode_object_get] OBJ ID: 31 (5)
[ 4.759125] [drm:drm_mode_object_get] OBJ ID: 31 (6)
[ 4.759140] [drm:drm_atomic_get_connector_state] Added [CONNECTOR:31:DSI-1] (ptrval) state to (ptrval)
[ 4.759153] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6)
[ 4.759168] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [NOCRTC]
[ 4.759180] [drm:drm_mode_object_get] OBJ ID: 31 (5)
[ 4.759196] [drm:drm_atomic_set_crtc_for_connector] Link [CONNECTOR:31:DSI-1] state (ptrval) to [CRTC:49:crtc-0]
[ 4.759209] [drm:drm_atomic_check_only] checking (ptrval)
[ 4.759224] [drm:dsi_mgr_connector_best_encoder]
[ 4.759244] [drm:drm_atomic_helper_check_modeset] Updating routing for [CONNECTOR:31:DSI-1]
[ 4.759254] [drm:dsi_mgr_connector_best_encoder]
[ 4.759275] [drm:drm_atomic_helper_check_modeset] [CONNECTOR:31:DSI-1] keeps [ENCODER:30:DSI-30], now on [CRTC:49:crtc-0]
[ 4.759293] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 4.759316] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 4.759333] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 4.759347] [drm:drm_atomic_commit] committing (ptrval)
[ 4.759369] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 4.759413] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 5.840800] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[ 8.871442] udevd[752]: starting version 3.2.7
[ 8.876350] random: udevd: uninitialized urandom read (16 bytes read)
[ 8.877358] random: udevd: uninitialized urandom read (16 bytes read)
[ 8.877459] random: udevd: uninitialized urandom read (16 bytes read)
[ 8.908690] udevd[753]: starting eudev-3.2.7
[ 9.563857] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 9.588748] inv-mpu6050-i2c 3-0068: mounting matrix not found: using identity...
[ 9.606791] input: pm8941_pwrkey as /devices/platform/soc/fc4cf000.spmi/spmi-0/0-00/fc4cf000.spmi:pm8941@0:pwrkey@800/input/input1
[ 9.679456] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 9.680082] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 9.680093] cfg80211: failed to load regulatory.db
[ 9.797045] ak8975 4-000f: mounting matrix not found: using identity...
[ 9.825968] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2
[ 9.835347] brcmfmac mmc0:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.lge,hammerhead.txt failed with error -2
[ 10.163863] i2c i2c-3: Added multiplexed i2c bus 4
[ 12.344803] e cgroup1: Need name or subsystem set
[ 12.682849] urandom_read: 2 callbacks suppressed
[ 12.682860] random: mktemp: uninitialized urandom read (10 bytes read)
[ 15.201752] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out
[ 18.574025] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 19.368235] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 19.522781] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 19.955263] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 20.160328] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 20.395962] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 23.364779] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 24.303460] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 24.390171] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 25.441747] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:32:plane-0] flip_done timed out
[ 25.441806] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 25.441820] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 25.441835] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 25.441848] [drm:mdp5_plane_atomic_update] plane-0: update
[ 25.441865] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 25.441877] [drm:mdp5_plane_mode_set] scale config = 0
[ 25.441909] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 25.441914] ------------[ cut here ]------------
[ 25.441928] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c:709 mdp5_crtc_atomic_flush+0x174/0x190
[ 25.441933] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod
[ 25.442026] CPU: 0 PID: 100 Comm: kworker/0:2 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 25.442035] Hardware name: Generic DT based system
[ 25.442054] Workqueue: events deferred_probe_work_func
[ 25.442079] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 25.442094] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 25.442110] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 25.442124] [<c0321660>] (__warn.part.3) from [<c03217d8>] (warn_slowpath_null+0x44/0x4c)
[ 25.442137] [<c03217d8>] (warn_slowpath_null) from [<c07ad97c>] (mdp5_crtc_atomic_flush+0x174/0x190)
[ 25.442152] [<c07ad97c>] (mdp5_crtc_atomic_flush) from [<c075f5e0>] (drm_atomic_helper_commit_planes+0x1fc/0x270)
[ 25.442172] [<c075f5e0>] (drm_atomic_helper_commit_planes) from [<c07ddd04>] (msm_atomic_commit_tail+0x44/0x140)
[ 25.442187] [<c07ddd04>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 25.442198] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 25.442210] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4)
[ 25.442219] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c0766c48>] (drm_fb_helper_pan_display+0xc4/0x1d8)
[ 25.442234] [<c0766c48>] (drm_fb_helper_pan_display) from [<c06e7c38>] (fb_pan_display+0x9c/0x110)
[ 25.442247] [<c06e7c38>] (fb_pan_display) from [<c06f3528>] (bit_update_start+0x14/0x30)
[ 25.442257] [<c06f3528>] (bit_update_start) from [<c06f215c>] (fbcon_switch+0x390/0x514)
[ 25.442269] [<c06f215c>] (fbcon_switch) from [<c073d5d4>] (redraw_screen+0x13c/0x244)
[ 25.442280] [<c073d5d4>] (redraw_screen) from [<c073e010>] (do_bind_con_driver+0x354/0x3c4)
[ 25.442291] [<c073e010>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0)
[ 25.442300] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8)
[ 25.442317] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80)
[ 25.442329] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68)
[ 25.442341] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304)
[ 25.442354] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c)
[ 25.442371] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc)
[ 25.442383] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634)
[ 25.442399] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4)
[ 25.442412] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174)
[ 25.442427] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98)
[ 25.442441] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c)
[ 25.442452] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0)
[ 25.442463] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4)
[ 25.442474] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168)
[ 25.442484] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c)
[ 25.442494] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4)
[ 25.442510] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 25.442524] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 25.442537] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 25.442548] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 25.442558] Exception stack(0xc4e09fb0 to 0xc4e09ff8)
[ 25.442577] 9fa0: 00000000 00000000 00000000 00000000
[ 25.442601] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 25.442623] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 25.442632] ---[ end trace d4b922f6bb6a2605 ]---
[ 25.442663] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 25.442677] [drm:crtc_flush] crtc-0: flush=00000840
[ 25.501752] msm fd900000.mdss: pp done time out, lm=0
[ 25.561740] ------------[ cut here ]------------
[ 25.561758] WARNING: CPU: 0 PID: 100 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 25.561766] [CRTC:49:crtc-0] vblank wait timed out
[ 25.561770] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod
[ 25.561854] CPU: 0 PID: 100 Comm: kworker/0:2 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 25.561863] Hardware name: Generic DT based system
[ 25.561879] Workqueue: events deferred_probe_work_func
[ 25.561897] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 25.561908] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 25.561921] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 25.561933] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 25.561947] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 25.561963] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 25.561980] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 25.561993] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 25.562005] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 25.562015] [<c076368c>] (drm_atomic_helper_commit) from [<c0766a88>] (restore_fbdev_mode_atomic+0x168/0x1d4)
[ 25.562024] [<c0766a88>] (restore_fbdev_mode_atomic) from [<c0766c48>] (drm_fb_helper_pan_display+0xc4/0x1d8)
[ 25.562036] [<c0766c48>] (drm_fb_helper_pan_display) from [<c06e7c38>] (fb_pan_display+0x9c/0x110)
[ 25.562047] [<c06e7c38>] (fb_pan_display) from [<c06f3528>] (bit_update_start+0x14/0x30)
[ 25.562056] [<c06f3528>] (bit_update_start) from [<c06f215c>] (fbcon_switch+0x390/0x514)
[ 25.562066] [<c06f215c>] (fbcon_switch) from [<c073d5d4>] (redraw_screen+0x13c/0x244)
[ 25.562076] [<c073d5d4>] (redraw_screen) from [<c073e010>] (do_bind_con_driver+0x354/0x3c4)
[ 25.562085] [<c073e010>] (do_bind_con_driver) from [<c073e44c>] (do_take_over_console+0x150/0x1f0)
[ 25.562095] [<c073e44c>] (do_take_over_console) from [<c06ef97c>] (do_fbcon_takeover+0x78/0xd8)
[ 25.562107] [<c06ef97c>] (do_fbcon_takeover) from [<c0343b04>] (notifier_call_chain+0x48/0x80)
[ 25.562118] [<c0343b04>] (notifier_call_chain) from [<c03442b8>] (blocking_notifier_call_chain+0x50/0x68)
[ 25.562129] [<c03442b8>] (blocking_notifier_call_chain) from [<c06e9794>] (register_framebuffer+0x224/0x304)
[ 25.562142] [<c06e9794>] (register_framebuffer) from [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock+0x2f0/0x53c)
[ 25.562156] [<c076a45c>] (__drm_fb_helper_initial_config_and_unlock) from [<c07e9b18>] (msm_fbdev_init+0x74/0xbc)
[ 25.562166] [<c07e9b18>] (msm_fbdev_init) from [<c07df768>] (msm_drm_bind+0x560/0x634)
[ 25.562179] [<c07df768>] (msm_drm_bind) from [<c07fbb18>] (try_to_bring_up_master+0x1f8/0x2b4)
[ 25.562192] [<c07fbb18>] (try_to_bring_up_master) from [<c07fbc84>] (__component_add+0xb0/0x174)
[ 25.562206] [<c07fbc84>] (__component_add) from [<c08043d4>] (platform_drv_probe+0x48/0x98)
[ 25.562218] [<c08043d4>] (platform_drv_probe) from [<c0802068>] (really_probe+0x248/0x40c)
[ 25.562229] [<c0802068>] (really_probe) from [<c08023dc>] (driver_probe_device+0x74/0x1c0)
[ 25.562239] [<c08023dc>] (driver_probe_device) from [<c08001d0>] (bus_for_each_drv+0x80/0xc4)
[ 25.562250] [<c08001d0>] (bus_for_each_drv) from [<c0801d80>] (__device_attach+0xd0/0x168)
[ 25.562260] [<c0801d80>] (__device_attach) from [<c0800f94>] (bus_probe_device+0x84/0x8c)
[ 25.562271] [<c0800f94>] (bus_probe_device) from [<c08014dc>] (deferred_probe_work_func+0x84/0xc4)
[ 25.562284] [<c08014dc>] (deferred_probe_work_func) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 25.562297] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 25.562309] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 25.562319] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 25.562328] Exception stack(0xc4e09fb0 to 0xc4e09ff8)
[ 25.562345] 9fa0: 00000000 00000000 00000000 00000000
[ 25.562370] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 25.562391] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 25.562399] ---[ end trace d4b922f6bb6a2606 ]---
[ 25.562431] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50]
[ 25.562453] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 25.562467] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (6)
[ 25.562480] [drm:drm_mode_object_put.part.0] OBJ ID: 31 (5)
[ 25.562493] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2)
[ 25.562507] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3)
[ 25.562526] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 25.571673] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 25.571690] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 25.571705] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 25.571720] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 25.571732] [drm:drm_mode_object_get] OBJ ID: 53 (1)
[ 25.571745] [drm:drm_atomic_check_only] checking (ptrval)
[ 25.571767] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 25.571787] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 25.571804] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 25.571817] [drm:drm_atomic_commit] committing (ptrval)
[ 25.571836] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 26.223530] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 35.681745] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out
[ 40.478585] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 40.531284] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 40.593999] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 40.916158] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 43.157049] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 45.172624] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z)
[ 45.921742] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:32:plane-0] flip_done timed out
[ 45.921787] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 45.921801] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 45.921814] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 45.921827] [drm:mdp5_plane_atomic_update] plane-0: update
[ 45.921842] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 45.921854] [drm:mdp5_plane_mode_set] scale config = 0
[ 45.921879] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 45.921884] ------------[ cut here ]------------
[ 45.921898] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c:709 mdp5_crtc_atomic_flush+0x174/0x190
[ 45.921902] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod
[ 45.921990] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 45.921998] Hardware name: Generic DT based system
[ 45.922014] Workqueue: events drm_fb_helper_dirty_work
[ 45.922034] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 45.922046] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 45.922061] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 45.922073] [<c0321660>] (__warn.part.3) from [<c03217d8>] (warn_slowpath_null+0x44/0x4c)
[ 45.922086] [<c03217d8>] (warn_slowpath_null) from [<c07ad97c>] (mdp5_crtc_atomic_flush+0x174/0x190)
[ 45.922099] [<c07ad97c>] (mdp5_crtc_atomic_flush) from [<c075f5e0>] (drm_atomic_helper_commit_planes+0x1fc/0x270)
[ 45.922115] [<c075f5e0>] (drm_atomic_helper_commit_planes) from [<c07ddd04>] (msm_atomic_commit_tail+0x44/0x140)
[ 45.922129] [<c07ddd04>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 45.922141] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 45.922156] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204)
[ 45.922169] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164)
[ 45.922182] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 45.922195] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 45.922208] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 45.922219] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 45.922228] Exception stack(0xde965fb0 to 0xde965ff8)
[ 45.922246] 5fa0: 00000000 00000000 00000000 00000000
[ 45.922271] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 45.922291] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 45.922299] ---[ end trace d4b922f6bb6a2607 ]---
[ 45.922328] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 45.922343] [drm:crtc_flush] crtc-0: flush=00000840
[ 45.981760] msm fd900000.mdss: pp done time out, lm=0
[ 46.041730] ------------[ cut here ]------------
[ 46.041748] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 46.041756] [CRTC:49:crtc-0] vblank wait timed out
[ 46.041760] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod
[ 46.041843] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 46.041851] Hardware name: Generic DT based system
[ 46.041866] Workqueue: events drm_fb_helper_dirty_work
[ 46.041884] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 46.041895] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 46.041907] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 46.041919] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 46.041933] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 46.041948] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 46.041964] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 46.041978] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 46.041990] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 46.042003] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204)
[ 46.042014] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164)
[ 46.042026] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 46.042039] [<c033c4b0>] (process_one_work) from [<c033d108>] (worker_thread+0x44/0x584)
[ 46.042051] [<c033d108>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 46.042061] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 46.042070] Exception stack(0xde965fb0 to 0xde965ff8)
[ 46.042087] 5fa0: 00000000 00000000 00000000 00000000
[ 46.042112] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 46.042134] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 46.042141] ---[ end trace d4b922f6bb6a2608 ]---
[ 46.042171] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50]
[ 46.042187] [drm:drm_mode_object_put.part.0] OBJ ID: 53 (2)
[ 46.042204] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 46.042215] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2)
[ 46.042230] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3)
[ 46.042244] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 46.042273] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 46.042291] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 46.042306] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 46.042320] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 46.042335] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 46.042346] [drm:drm_mode_object_get] OBJ ID: 54 (1)
[ 46.042359] [drm:drm_atomic_check_only] checking (ptrval)
[ 46.042376] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 46.042395] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 46.042411] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 46.042423] [drm:drm_atomic_commit] committing (ptrval)
[ 46.042440] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 56.161749] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:49:crtc-0] flip_done timed out
[ 59.666659] [drm:dsi_host_irq] isr=0x2000700, id=0
[ 61.315067] [drm:mdp5_crtc_vblank_irq] crtc-0: send event: (ptrval)
[ 61.315103] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 61.315117] [drm:vblank_disable_fn] disabling vblank on crtc 0
[ 61.315136] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 61.315147] [drm:msm_disable_vblank] dev=(ptrval), crtc=0
[ 61.315220] [drm:drm_calc_timestamping_constants] crtc 49: hwmode: htotal 1086, vtotal 1926, vdisplay 1920
[ 61.315234] [drm:drm_calc_timestamping_constants] crtc 49: clock 150000 kHz framedur 13944240 linedur 7240
[ 61.315247] [drm:drm_atomic_helper_commit_planes] crtc-0: begin
[ 61.315260] [drm:mdp5_plane_atomic_update] plane-0: update
[ 61.315275] [drm:mdp5_plane_mode_set] plane-0: FB[50] 0,0,1080,1920 -> CRTC[49] 0,0,1080,1920
[ 61.315286] [drm:mdp5_plane_mode_set] scale config = 0
[ 61.315311] [drm:mdp5_crtc_atomic_flush] crtc-0: event: (ptrval)
[ 61.315337] [drm:mdp5_ctl_blend] lm0: blend config = 0x00040000. ext_cfg = 0x00000000
[ 61.315351] [drm:crtc_flush] crtc-0: flush=00000840
[ 61.315369] [drm:msm_enable_vblank] dev=(ptrval), crtc=0
[ 61.315388] [drm:drm_vblank_enable] enabling vblank on crtc 0, ret: 0
[ 61.315406] [drm:drm_update_vblank_count] updating vblank count on crtc 0: current=1, diff=0, hw=0 hw_last=0
[ 61.318527] [drm:dsi_host_irq] isr=0x2000700, id=0
[ 61.371744] msm fd900000.mdss: pp done time out, lm=0
[ 61.431730] ------------[ cut here ]------------
[ 61.431747] WARNING: CPU: 0 PID: 20 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 61.431754] [CRTC:49:crtc-0] vblank wait timed out
[ 61.431758] Modules linked in: brcmfmac brcmutil qcom_spmi_vadc qcom_vadc_common pm8941_pwrkey qcom_spmi_iadc inv_mpu6050_i2c inv_mpu6050 tsl2772 bq24190_charger cfg80211 dm_mod
[ 61.431843] CPU: 0 PID: 20 Comm: kworker/0:1 Tainted: G W 5.1.0-rc6-next-20190426-00009-g75891c3edac4-dirty #303
[ 61.431851] Hardware name: Generic DT based system
[ 61.431866] Workqueue: events drm_fb_helper_dirty_work
[ 61.431885] [<c031229c>] (unwind_backtrace) from [<c030d5ac>] (show_stack+0x10/0x14)
[ 61.431896] [<c030d5ac>] (show_stack) from [<c0ac152c>] (dump_stack+0x78/0x8c)
[ 61.431909] [<c0ac152c>] (dump_stack) from [<c0321660>] (__warn.part.3+0xb8/0xd4)
[ 61.431922] [<c0321660>] (__warn.part.3) from [<c03216e0>] (warn_slowpath_fmt+0x64/0x88)
[ 61.431936] [<c03216e0>] (warn_slowpath_fmt) from [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290)
[ 61.431952] [<c0761ca4>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c07b0d50>] (mdp5_complete_commit+0x14/0x40)
[ 61.431968] [<c07b0d50>] (mdp5_complete_commit) from [<c07ddd68>] (msm_atomic_commit_tail+0xa8/0x140)
[ 61.431981] [<c07ddd68>] (msm_atomic_commit_tail) from [<c076359c>] (commit_tail+0x40/0x6c)
[ 61.431993] [<c076359c>] (commit_tail) from [<c076368c>] (drm_atomic_helper_commit+0xbc/0x128)
[ 61.432006] [<c076368c>] (drm_atomic_helper_commit) from [<c0765800>] (drm_atomic_helper_dirtyfb+0x158/0x204)
[ 61.432017] [<c0765800>] (drm_atomic_helper_dirtyfb) from [<c076711c>] (drm_fb_helper_dirty_work+0x15c/0x164)
[ 61.432031] [<c076711c>] (drm_fb_helper_dirty_work) from [<c033c4b0>] (process_one_work+0x1fc/0x564)
[ 61.432043] [<c033c4b0>] (process_one_work) from [<c033d384>] (worker_thread+0x2c0/0x584)
[ 61.432055] [<c033d384>] (worker_thread) from [<c034247c>] (kthread+0x148/0x150)
[ 61.432066] [<c034247c>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 61.432075] Exception stack(0xde965fb0 to 0xde965ff8)
[ 61.432092] 5fa0: 00000000 00000000 00000000 00000000
[ 61.432117] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 61.432138] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 61.432147] ---[ end trace d4b922f6bb6a2609 ]---
[ 61.432176] [drm:mdp5_plane_cleanup_fb] plane-0: cleanup: FB[50]
[ 61.432192] [drm:drm_mode_object_put.part.0] OBJ ID: 54 (2)
[ 61.432207] [drm:drm_atomic_state_default_clear] Clearing atomic state (ptrval)
[ 61.432219] [drm:drm_mode_object_put.part.0] OBJ ID: 51 (2)
[ 61.432232] [drm:drm_mode_object_put.part.0] OBJ ID: 50 (3)
[ 61.432245] [drm:__drm_atomic_state_free] Freeing atomic state (ptrval)
[ 61.432373] msm fd900000.mdss: fb0: msmdrmfb frame buffer device
[ 61.432405] [drm:drm_atomic_state_init] Allocated atomic state (ptrval)
[ 61.432423] [drm:drm_mode_object_get] OBJ ID: 50 (2)
[ 61.432438] [drm:drm_atomic_get_plane_state] Added [PLANE:32:plane-0] (ptrval) state to (ptrval)
[ 61.432452] [drm:drm_mode_object_get] OBJ ID: 51 (1)
[ 61.432470] [drm:drm_atomic_get_crtc_state] Added [CRTC:49:crtc-0] (ptrval) state to (ptrval)
[ 61.432482] [drm:drm_mode_object_get] OBJ ID: 55 (1)
[ 61.432496] [drm:drm_atomic_check_only] checking (ptrval)
[ 61.432515] [drm:mdp5_plane_atomic_check] plane-0: check (1 -> 1)
[ 61.432534] [drm:mdp5_crtc_atomic_check] crtc-0: check
[ 61.432552] [drm:mdp5_crtc_atomic_check] crtc-0: assign pipe plane-0 on stage=1
[ 61.432566] [drm:drm_atomic_commit] committing (ptrval)
[ 61.432583] [drm:msm_framebuffer_prepare] FB[50]: iova[0]: 20101000 (0)
[ 62.481750] [drm:drm_sysfs_hotplug_event] generating hotplug event
[-- Attachment #3: Type: text/plain, Size: 159 bytes --]
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH v2 1/6] drm: msm: remove resv fields from msm_gem_object struct
2019-05-09 2:03 ` [PATCH v2 1/6] drm: msm: remove resv fields from msm_gem_object struct Brian Masney
@ 2019-05-13 20:32 ` Bjorn Andersson
2019-05-13 22:25 ` Brian Masney
0 siblings, 1 reply; 35+ messages in thread
From: Bjorn Andersson @ 2019-05-13 20:32 UTC (permalink / raw)
To: Brian Masney
Cc: robdclark, sean, dri-devel, linux-arm-msm, freedreno, airlied,
daniel, linux-kernel, linus.walleij, jonathan, robh
On Wed 08 May 19:03 PDT 2019, Brian Masney wrote:
> The msm_gem_object structure contains resv and _resv fields that are
> no longer needed since the reservation object is now stored on
> drm_gem_object. msm_atomic_prepare_fb() and msm_atomic_prepare_fb()
> both referenced the wrong reservation object, and would lead to an
> attempt to dereference a NULL pointer. Correct those two cases to
> point to the correct reservation object.
>
> Signed-off-by: Brian Masney <masneyb@onstation.org>
> Fixes: dd55cf6929e6 ("drm: msm: Switch to use drm_gem_object reservation_object")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This resolves a NULL-pointer dereference about to show up in v5.2-rc1,
so please pick this up for -rc.
Regards,
Bjorn
> ---
> Patch introduced in v2
>
> drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 4 +---
> drivers/gpu/drm/msm/msm_atomic.c | 4 +---
> drivers/gpu/drm/msm/msm_gem.c | 3 ---
> drivers/gpu/drm/msm/msm_gem.h | 4 ----
> 4 files changed, 2 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> index da1f727d7495..ce1a555e1f31 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> @@ -780,7 +780,6 @@ static int dpu_plane_prepare_fb(struct drm_plane *plane,
> struct dpu_plane_state *pstate = to_dpu_plane_state(new_state);
> struct dpu_hw_fmt_layout layout;
> struct drm_gem_object *obj;
> - struct msm_gem_object *msm_obj;
> struct dma_fence *fence;
> struct dpu_kms *kms = _dpu_plane_get_kms(&pdpu->base);
> int ret;
> @@ -799,8 +798,7 @@ static int dpu_plane_prepare_fb(struct drm_plane *plane,
> * implicit fence and fb prepare by hand here.
> */
> obj = msm_framebuffer_bo(new_state->fb, 0);
> - msm_obj = to_msm_bo(obj);
> - fence = reservation_object_get_excl_rcu(msm_obj->resv);
> + fence = reservation_object_get_excl_rcu(obj->resv);
> if (fence)
> drm_atomic_set_fence_for_plane(new_state, fence);
>
> diff --git a/drivers/gpu/drm/msm/msm_atomic.c b/drivers/gpu/drm/msm/msm_atomic.c
> index f5b1256e32b6..131c23a267ee 100644
> --- a/drivers/gpu/drm/msm/msm_atomic.c
> +++ b/drivers/gpu/drm/msm/msm_atomic.c
> @@ -49,15 +49,13 @@ int msm_atomic_prepare_fb(struct drm_plane *plane,
> struct msm_drm_private *priv = plane->dev->dev_private;
> struct msm_kms *kms = priv->kms;
> struct drm_gem_object *obj;
> - struct msm_gem_object *msm_obj;
> struct dma_fence *fence;
>
> if (!new_state->fb)
> return 0;
>
> obj = msm_framebuffer_bo(new_state->fb, 0);
> - msm_obj = to_msm_bo(obj);
> - fence = reservation_object_get_excl_rcu(msm_obj->resv);
> + fence = reservation_object_get_excl_rcu(obj->resv);
>
> drm_atomic_set_fence_for_plane(new_state, fence);
>
> diff --git a/drivers/gpu/drm/msm/msm_gem.c b/drivers/gpu/drm/msm/msm_gem.c
> index 31d5a744d84f..947508e8269d 100644
> --- a/drivers/gpu/drm/msm/msm_gem.c
> +++ b/drivers/gpu/drm/msm/msm_gem.c
> @@ -973,9 +973,6 @@ static int msm_gem_new_impl(struct drm_device *dev,
> msm_obj->flags = flags;
> msm_obj->madv = MSM_MADV_WILLNEED;
>
> - if (resv)
> - msm_obj->base.resv = resv;
> -
> INIT_LIST_HEAD(&msm_obj->submit_entry);
> INIT_LIST_HEAD(&msm_obj->vmas);
>
> diff --git a/drivers/gpu/drm/msm/msm_gem.h b/drivers/gpu/drm/msm/msm_gem.h
> index c5ac781dffee..812d1b1369a5 100644
> --- a/drivers/gpu/drm/msm/msm_gem.h
> +++ b/drivers/gpu/drm/msm/msm_gem.h
> @@ -86,10 +86,6 @@ struct msm_gem_object {
>
> struct llist_node freed;
>
> - /* normally (resv == &_resv) except for imported bo's */
> - struct reservation_object *resv;
> - struct reservation_object _resv;
> -
> /* For physically contiguous buffers. Used when we don't have
> * an IOMMU. Also used for stolen/splashscreen buffer.
> */
> --
> 2.20.1
>
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH v2 1/6] drm: msm: remove resv fields from msm_gem_object struct
2019-05-13 20:32 ` Bjorn Andersson
@ 2019-05-13 22:25 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-13 22:25 UTC (permalink / raw)
To: Bjorn Andersson
Cc: robdclark, sean, dri-devel, linux-arm-msm, freedreno, airlied,
daniel, linux-kernel, linus.walleij, jonathan, robh
On Mon, May 13, 2019 at 01:32:39PM -0700, Bjorn Andersson wrote:
> On Wed 08 May 19:03 PDT 2019, Brian Masney wrote:
>
> > The msm_gem_object structure contains resv and _resv fields that are
> > no longer needed since the reservation object is now stored on
> > drm_gem_object. msm_atomic_prepare_fb() and msm_atomic_prepare_fb()
> > both referenced the wrong reservation object, and would lead to an
> > attempt to dereference a NULL pointer. Correct those two cases to
> > point to the correct reservation object.
> >
> > Signed-off-by: Brian Masney <masneyb@onstation.org>
> > Fixes: dd55cf6929e6 ("drm: msm: Switch to use drm_gem_object reservation_object")
>
> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
>
> This resolves a NULL-pointer dereference about to show up in v5.2-rc1,
> so please pick this up for -rc.
Let me send out another version of just this patch. This snippet below
that I removed needs to stay. I got a little too over eager removing
code.
> > @@ -973,9 +973,6 @@ static int msm_gem_new_impl(struct drm_device *dev,
> > msm_obj->flags = flags;
> > msm_obj->madv = MSM_MADV_WILLNEED;
> >
> > - if (resv)
> > - msm_obj->base.resv = resv;
> > -
> > INIT_LIST_HEAD(&msm_obj->submit_entry);
> > INIT_LIST_HEAD(&msm_obj->vmas);
> >
Brian
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-09 2:03 [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support Brian Masney
` (6 preceding siblings ...)
2019-05-09 2:06 ` Brian Masney
@ 2019-05-28 13:46 ` Linus Walleij
2019-05-29 1:17 ` Brian Masney
7 siblings, 1 reply; 35+ messages in thread
From: Linus Walleij @ 2019-05-28 13:46 UTC (permalink / raw)
To: Brian Masney
Cc: Rob Clark, Sean Paul, open list:DRM PANEL DRIVERS, MSM,
freedreno, Dave Airlie, Daniel Vetter, linux-kernel,
Jonathan Marek, Rob Herring
On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote:
> Here is a patch series that adds initial display support for the LG
> Nexus 5 (hammerhead) phone. It's not fully working so that's why some
> of these patches are RFC until we can get it fully working.
>
> The phones boots into terminal mode, however there is a several second
> (or more) delay when writing to tty1 compared to when the changes are
> actually shown on the screen. The following errors are in dmesg:
I tested to apply patches 2-6 and got the console up on the phone as well.
I see the same timouts, and I also notice the update is slow in the
display, as if the DSI panel was running in low power (LP) mode.
Was booting this to do some other work, but happy to see the progress!
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-28 13:46 ` Linus Walleij
@ 2019-05-29 1:17 ` Brian Masney
2019-05-29 1:32 ` Jeffrey Hugo
` (2 more replies)
0 siblings, 3 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-29 1:17 UTC (permalink / raw)
To: Linus Walleij
Cc: Rob Clark, Sean Paul, open list:DRM PANEL DRIVERS, MSM,
freedreno, Dave Airlie, Daniel Vetter, linux-kernel,
Jonathan Marek, Rob Herring
On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote:
> On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote:
>
> > Here is a patch series that adds initial display support for the LG
> > Nexus 5 (hammerhead) phone. It's not fully working so that's why some
> > of these patches are RFC until we can get it fully working.
> >
> > The phones boots into terminal mode, however there is a several second
> > (or more) delay when writing to tty1 compared to when the changes are
> > actually shown on the screen. The following errors are in dmesg:
>
> I tested to apply patches 2-6 and got the console up on the phone as well.
> I see the same timouts, and I also notice the update is slow in the
> display, as if the DSI panel was running in low power (LP) mode.
>
> Was booting this to do some other work, but happy to see the progress!
Thanks!
I've had three people email me off list regarding the display working on
4.17 before the msm kms/drm driver was converted to the DRM atomic API so
this email is to get some more information out publicly.
I pushed up a branch to my github with 15 patches applied against 4.17
that has a working display:
https://github.com/masneyb/linux/commits/display-works-4.17
It's in low speed mode but its usable. The first 10 patches are in
mainline now and the last 5 are in essence this patch series with the
exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'.
There's a slightly different version of that patch in mainline now.
I'm planning to work on the msm8974 interconnect support once some of
the outstanding interconnect patches for the msm kms/drm driver arrive
in mainline. I'd really like to understand why the display works on
4.17 with those patches though. I assume that it's related to the
vblank events not working properly? Let me preface this with I'm a
total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't
looking for these events in the atomic commits before the migration?
See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic
helper commit"), specifically the drm_atomic_helper_wait_for_vblanks()
call that was added.
Brian
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [Freedreno] [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-29 1:17 ` Brian Masney
@ 2019-05-29 1:32 ` Jeffrey Hugo
2019-05-29 2:14 ` Rob Clark
2019-05-29 6:23 ` Linus Walleij
2 siblings, 0 replies; 35+ messages in thread
From: Jeffrey Hugo @ 2019-05-29 1:32 UTC (permalink / raw)
To: Brian Masney
Cc: Linus Walleij, Sean Paul, Rob Herring, Jonathan Marek,
Dave Airlie, MSM, linux-kernel, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter, freedreno
On Tue, May 28, 2019 at 7:17 PM Brian Masney <masneyb@onstation.org> wrote:
>
> On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote:
> > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote:
> >
> > > Here is a patch series that adds initial display support for the LG
> > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some
> > > of these patches are RFC until we can get it fully working.
> > >
> > > The phones boots into terminal mode, however there is a several second
> > > (or more) delay when writing to tty1 compared to when the changes are
> > > actually shown on the screen. The following errors are in dmesg:
> >
> > I tested to apply patches 2-6 and got the console up on the phone as well.
> > I see the same timouts, and I also notice the update is slow in the
> > display, as if the DSI panel was running in low power (LP) mode.
> >
> > Was booting this to do some other work, but happy to see the progress!
>
> Thanks!
>
> I've had three people email me off list regarding the display working on
> 4.17 before the msm kms/drm driver was converted to the DRM atomic API so
> this email is to get some more information out publicly.
>
> I pushed up a branch to my github with 15 patches applied against 4.17
> that has a working display:
>
> https://github.com/masneyb/linux/commits/display-works-4.17
>
> It's in low speed mode but its usable. The first 10 patches are in
> mainline now and the last 5 are in essence this patch series with the
> exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'.
> There's a slightly different version of that patch in mainline now.
>
> I'm planning to work on the msm8974 interconnect support once some of
> the outstanding interconnect patches for the msm kms/drm driver arrive
> in mainline. I'd really like to understand why the display works on
> 4.17 with those patches though. I assume that it's related to the
> vblank events not working properly? Let me preface this with I'm a
> total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't
> looking for these events in the atomic commits before the migration?
> See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic
> helper commit"), specifically the drm_atomic_helper_wait_for_vblanks()
> call that was added.
Do you know if the nexus 5 has a video or command mode panel? There
is some glitchyness with vblanks and command mode panels.
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-29 1:32 ` Jeffrey Hugo
0 siblings, 0 replies; 35+ messages in thread
From: Jeffrey Hugo @ 2019-05-29 1:32 UTC (permalink / raw)
To: Brian Masney
Cc: Rob Herring, Jonathan Marek, Dave Airlie, MSM, Linus Walleij,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter,
freedreno-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW, Sean Paul
On Tue, May 28, 2019 at 7:17 PM Brian Masney <masneyb@onstation.org> wrote:
>
> On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote:
> > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote:
> >
> > > Here is a patch series that adds initial display support for the LG
> > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some
> > > of these patches are RFC until we can get it fully working.
> > >
> > > The phones boots into terminal mode, however there is a several second
> > > (or more) delay when writing to tty1 compared to when the changes are
> > > actually shown on the screen. The following errors are in dmesg:
> >
> > I tested to apply patches 2-6 and got the console up on the phone as well.
> > I see the same timouts, and I also notice the update is slow in the
> > display, as if the DSI panel was running in low power (LP) mode.
> >
> > Was booting this to do some other work, but happy to see the progress!
>
> Thanks!
>
> I've had three people email me off list regarding the display working on
> 4.17 before the msm kms/drm driver was converted to the DRM atomic API so
> this email is to get some more information out publicly.
>
> I pushed up a branch to my github with 15 patches applied against 4.17
> that has a working display:
>
> https://github.com/masneyb/linux/commits/display-works-4.17
>
> It's in low speed mode but its usable. The first 10 patches are in
> mainline now and the last 5 are in essence this patch series with the
> exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'.
> There's a slightly different version of that patch in mainline now.
>
> I'm planning to work on the msm8974 interconnect support once some of
> the outstanding interconnect patches for the msm kms/drm driver arrive
> in mainline. I'd really like to understand why the display works on
> 4.17 with those patches though. I assume that it's related to the
> vblank events not working properly? Let me preface this with I'm a
> total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't
> looking for these events in the atomic commits before the migration?
> See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic
> helper commit"), specifically the drm_atomic_helper_wait_for_vblanks()
> call that was added.
Do you know if the nexus 5 has a video or command mode panel? There
is some glitchyness with vblanks and command mode panels.
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [Freedreno] [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-29 1:32 ` Jeffrey Hugo
(?)
@ 2019-05-29 1:37 ` Brian Masney
2019-05-29 1:42 ` Jeffrey Hugo
-1 siblings, 1 reply; 35+ messages in thread
From: Brian Masney @ 2019-05-29 1:37 UTC (permalink / raw)
To: Jeffrey Hugo
Cc: Linus Walleij, Sean Paul, Rob Herring, Jonathan Marek,
Dave Airlie, MSM, linux-kernel, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter, freedreno
On Tue, May 28, 2019 at 07:32:14PM -0600, Jeffrey Hugo wrote:
> On Tue, May 28, 2019 at 7:17 PM Brian Masney <masneyb@onstation.org> wrote:
> >
> > On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote:
> > > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote:
> > >
> > > > Here is a patch series that adds initial display support for the LG
> > > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some
> > > > of these patches are RFC until we can get it fully working.
> > > >
> > > > The phones boots into terminal mode, however there is a several second
> > > > (or more) delay when writing to tty1 compared to when the changes are
> > > > actually shown on the screen. The following errors are in dmesg:
> > >
> > > I tested to apply patches 2-6 and got the console up on the phone as well.
> > > I see the same timouts, and I also notice the update is slow in the
> > > display, as if the DSI panel was running in low power (LP) mode.
> > >
> > > Was booting this to do some other work, but happy to see the progress!
> >
> > Thanks!
> >
> > I've had three people email me off list regarding the display working on
> > 4.17 before the msm kms/drm driver was converted to the DRM atomic API so
> > this email is to get some more information out publicly.
> >
> > I pushed up a branch to my github with 15 patches applied against 4.17
> > that has a working display:
> >
> > https://github.com/masneyb/linux/commits/display-works-4.17
> >
> > It's in low speed mode but its usable. The first 10 patches are in
> > mainline now and the last 5 are in essence this patch series with the
> > exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'.
> > There's a slightly different version of that patch in mainline now.
> >
> > I'm planning to work on the msm8974 interconnect support once some of
> > the outstanding interconnect patches for the msm kms/drm driver arrive
> > in mainline. I'd really like to understand why the display works on
> > 4.17 with those patches though. I assume that it's related to the
> > vblank events not working properly? Let me preface this with I'm a
> > total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't
> > looking for these events in the atomic commits before the migration?
> > See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic
> > helper commit"), specifically the drm_atomic_helper_wait_for_vblanks()
> > call that was added.
>
> Do you know if the nexus 5 has a video or command mode panel? There
> is some glitchyness with vblanks and command mode panels.
Its in command mode. I know this because I see two 'pp done time out'
messages, even on 4.17. Based on my understanding, the ping pong code is
only applicable for command mode panels.
Brian
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [Freedreno] [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-29 1:37 ` [Freedreno] " Brian Masney
@ 2019-05-29 1:42 ` Jeffrey Hugo
2019-05-29 2:46 ` Brian Masney
0 siblings, 1 reply; 35+ messages in thread
From: Jeffrey Hugo @ 2019-05-29 1:42 UTC (permalink / raw)
To: Brian Masney
Cc: Linus Walleij, Sean Paul, Rob Herring, Jonathan Marek,
Dave Airlie, MSM, linux-kernel, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter, freedreno
On Tue, May 28, 2019 at 7:37 PM Brian Masney <masneyb@onstation.org> wrote:
>
> On Tue, May 28, 2019 at 07:32:14PM -0600, Jeffrey Hugo wrote:
> > On Tue, May 28, 2019 at 7:17 PM Brian Masney <masneyb@onstation.org> wrote:
> > >
> > > On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote:
> > > > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote:
> > > >
> > > > > Here is a patch series that adds initial display support for the LG
> > > > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some
> > > > > of these patches are RFC until we can get it fully working.
> > > > >
> > > > > The phones boots into terminal mode, however there is a several second
> > > > > (or more) delay when writing to tty1 compared to when the changes are
> > > > > actually shown on the screen. The following errors are in dmesg:
> > > >
> > > > I tested to apply patches 2-6 and got the console up on the phone as well.
> > > > I see the same timouts, and I also notice the update is slow in the
> > > > display, as if the DSI panel was running in low power (LP) mode.
> > > >
> > > > Was booting this to do some other work, but happy to see the progress!
> > >
> > > Thanks!
> > >
> > > I've had three people email me off list regarding the display working on
> > > 4.17 before the msm kms/drm driver was converted to the DRM atomic API so
> > > this email is to get some more information out publicly.
> > >
> > > I pushed up a branch to my github with 15 patches applied against 4.17
> > > that has a working display:
> > >
> > > https://github.com/masneyb/linux/commits/display-works-4.17
> > >
> > > It's in low speed mode but its usable. The first 10 patches are in
> > > mainline now and the last 5 are in essence this patch series with the
> > > exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'.
> > > There's a slightly different version of that patch in mainline now.
> > >
> > > I'm planning to work on the msm8974 interconnect support once some of
> > > the outstanding interconnect patches for the msm kms/drm driver arrive
> > > in mainline. I'd really like to understand why the display works on
> > > 4.17 with those patches though. I assume that it's related to the
> > > vblank events not working properly? Let me preface this with I'm a
> > > total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't
> > > looking for these events in the atomic commits before the migration?
> > > See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic
> > > helper commit"), specifically the drm_atomic_helper_wait_for_vblanks()
> > > call that was added.
> >
> > Do you know if the nexus 5 has a video or command mode panel? There
> > is some glitchyness with vblanks and command mode panels.
>
> Its in command mode. I know this because I see two 'pp done time out'
> messages, even on 4.17. Based on my understanding, the ping pong code is
> only applicable for command mode panels.
Actually, the ping pong element exists in both modes, but 'pp done
time out' is a good indicator that it is command mode.
Are you also seeing vblank timeouts?
Do you have busybox?
Can you run -
sudo busybox devmem 0xFD900614
sudo busybox devmem 0xFD900714
sudo busybox devmem 0xFD900814
sudo busybox devmem 0xFD900914
sudo busybox devmem 0xFD900A14
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-29 1:17 ` Brian Masney
2019-05-29 1:32 ` Jeffrey Hugo
@ 2019-05-29 2:14 ` Rob Clark
2019-05-29 2:24 ` [Freedreno] " Jeffrey Hugo
2019-05-29 6:23 ` Linus Walleij
2 siblings, 1 reply; 35+ messages in thread
From: Rob Clark @ 2019-05-29 2:14 UTC (permalink / raw)
To: Brian Masney
Cc: Linus Walleij, Sean Paul, open list:DRM PANEL DRIVERS, MSM,
freedreno, Dave Airlie, Daniel Vetter, linux-kernel,
Jonathan Marek, Rob Herring
On Tue, May 28, 2019 at 6:17 PM Brian Masney <masneyb@onstation.org> wrote:
>
> On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote:
> > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote:
> >
> > > Here is a patch series that adds initial display support for the LG
> > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some
> > > of these patches are RFC until we can get it fully working.
> > >
> > > The phones boots into terminal mode, however there is a several second
> > > (or more) delay when writing to tty1 compared to when the changes are
> > > actually shown on the screen. The following errors are in dmesg:
> >
> > I tested to apply patches 2-6 and got the console up on the phone as well.
> > I see the same timouts, and I also notice the update is slow in the
> > display, as if the DSI panel was running in low power (LP) mode.
> >
> > Was booting this to do some other work, but happy to see the progress!
>
> Thanks!
>
> I've had three people email me off list regarding the display working on
> 4.17 before the msm kms/drm driver was converted to the DRM atomic API so
> this email is to get some more information out publicly.
>
> I pushed up a branch to my github with 15 patches applied against 4.17
> that has a working display:
>
> https://github.com/masneyb/linux/commits/display-works-4.17
>
> It's in low speed mode but its usable. The first 10 patches are in
> mainline now and the last 5 are in essence this patch series with the
> exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'.
> There's a slightly different version of that patch in mainline now.
>
> I'm planning to work on the msm8974 interconnect support once some of
> the outstanding interconnect patches for the msm kms/drm driver arrive
> in mainline. I'd really like to understand why the display works on
> 4.17 with those patches though. I assume that it's related to the
> vblank events not working properly? Let me preface this with I'm a
> total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't
> looking for these events in the atomic commits before the migration?
> See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic
> helper commit"), specifically the drm_atomic_helper_wait_for_vblanks()
> call that was added.
interconnect probably good to get going anyways (and I need to find
some time to respin those mdp5/dpu patches) but I guess not related to
what you see (ie. I'd expect interconnect issue would trigger
underflow irq's)..
I'm not entirely sure why atomic would break things but cmd mode
panels aren't especially well tested. I can't find it now but there
was a thread (or IRC discussion?) that intf2vblank() should be
returning MDP5_IRQ_PING_PONG_<n>_DONE instead of
MDP5_IRQ_PING_PONG_<n>_RD_PTR, which seems likely and possibly related
to vblank timing issues..
BR,
-R
>
> Brian
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [Freedreno] [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-29 2:14 ` Rob Clark
@ 2019-05-29 2:24 ` Jeffrey Hugo
0 siblings, 0 replies; 35+ messages in thread
From: Jeffrey Hugo @ 2019-05-29 2:24 UTC (permalink / raw)
To: Rob Clark
Cc: Brian Masney, Sean Paul, Rob Herring, Jonathan Marek,
Dave Airlie, MSM, Linus Walleij, linux-kernel,
open list:DRM PANEL DRIVERS, Daniel Vetter, freedreno
On Tue, May 28, 2019 at 8:15 PM Rob Clark <robdclark@gmail.com> wrote:
>
> On Tue, May 28, 2019 at 6:17 PM Brian Masney <masneyb@onstation.org> wrote:
> >
> > On Tue, May 28, 2019 at 03:46:14PM +0200, Linus Walleij wrote:
> > > On Thu, May 9, 2019 at 4:04 AM Brian Masney <masneyb@onstation.org> wrote:
> > >
> > > > Here is a patch series that adds initial display support for the LG
> > > > Nexus 5 (hammerhead) phone. It's not fully working so that's why some
> > > > of these patches are RFC until we can get it fully working.
> > > >
> > > > The phones boots into terminal mode, however there is a several second
> > > > (or more) delay when writing to tty1 compared to when the changes are
> > > > actually shown on the screen. The following errors are in dmesg:
> > >
> > > I tested to apply patches 2-6 and got the console up on the phone as well.
> > > I see the same timouts, and I also notice the update is slow in the
> > > display, as if the DSI panel was running in low power (LP) mode.
> > >
> > > Was booting this to do some other work, but happy to see the progress!
> >
> > Thanks!
> >
> > I've had three people email me off list regarding the display working on
> > 4.17 before the msm kms/drm driver was converted to the DRM atomic API so
> > this email is to get some more information out publicly.
> >
> > I pushed up a branch to my github with 15 patches applied against 4.17
> > that has a working display:
> >
> > https://github.com/masneyb/linux/commits/display-works-4.17
> >
> > It's in low speed mode but its usable. The first 10 patches are in
> > mainline now and the last 5 are in essence this patch series with the
> > exception of 'drm/atomic+msm: add helper to implement legacy dirtyfb'.
> > There's a slightly different version of that patch in mainline now.
> >
> > I'm planning to work on the msm8974 interconnect support once some of
> > the outstanding interconnect patches for the msm kms/drm driver arrive
> > in mainline. I'd really like to understand why the display works on
> > 4.17 with those patches though. I assume that it's related to the
> > vblank events not working properly? Let me preface this with I'm a
> > total DRM newbie, but it looked like the pre-DRM-atomic driver wasn't
> > looking for these events in the atomic commits before the migration?
> > See commit 70db18dca4e0 ("drm/msm: Remove msm_commit/worker, use atomic
> > helper commit"), specifically the drm_atomic_helper_wait_for_vblanks()
> > call that was added.
>
> interconnect probably good to get going anyways (and I need to find
> some time to respin those mdp5/dpu patches) but I guess not related to
> what you see (ie. I'd expect interconnect issue would trigger
> underflow irq's)..
>
> I'm not entirely sure why atomic would break things but cmd mode
> panels aren't especially well tested. I can't find it now but there
> was a thread (or IRC discussion?) that intf2vblank() should be
> returning MDP5_IRQ_PING_PONG_<n>_DONE instead of
> MDP5_IRQ_PING_PONG_<n>_RD_PTR, which seems likely and possibly related
> to vblank timing issues..
That was an irc discussion, and I've changed my mind on that.
My big issue ended up being that autorefresh was enabled (which
basically turns the command panel into a pseudo video mode panel),
which appears incompatible with using the start kick. If FW is
configuring things in autorefresh mode, the driver likely doesn't
know, and will make a mess of things by using the start kick.
Disabling autorefresh would make the driver work as is, but fbcon
wouldn't work well (you'd need to do a start kick per frame, which
doesn't seem to happen). Removing the start kick and using the
autorefresh feature seemed better in my testing, but I haven't cleaned
up my code tree to send something up.
However, lets see how the hardware is actually configured in Brian's case.
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [Freedreno] [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-29 2:46 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-29 2:46 UTC (permalink / raw)
To: Jeffrey Hugo
Cc: Linus Walleij, Sean Paul, Rob Herring, Jonathan Marek,
Dave Airlie, MSM, linux-kernel, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter, freedreno
On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote:
> > > Do you know if the nexus 5 has a video or command mode panel? There
> > > is some glitchyness with vblanks and command mode panels.
> >
> > Its in command mode. I know this because I see two 'pp done time out'
> > messages, even on 4.17. Based on my understanding, the ping pong code is
> > only applicable for command mode panels.
>
> Actually, the ping pong element exists in both modes, but 'pp done
> time out' is a good indicator that it is command mode.
>
> Are you also seeing vblank timeouts?
Yes, here's a snippet of the first one.
[ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 2.556020] [CRTC:49:crtc-0] vblank wait timed out
[ 2.556023] Modules linked in:
[ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426
[ 2.556038] Hardware name: Generic DT based system
[ 2.556056] Workqueue: events deferred_probe_work_func
...
> Do you have busybox?
>
> Can you run -
> sudo busybox devmem 0xFD900614
> sudo busybox devmem 0xFD900714
> sudo busybox devmem 0xFD900814
> sudo busybox devmem 0xFD900914
> sudo busybox devmem 0xFD900A14
# busybox devmem 0xFD900614
0x00020020
# busybox devmem 0xFD900714
0x00000000
# busybox devmem 0xFD900814
0x00000000
# busybox devmem 0xFD900914
0x00000000
# busybox devmem 0xFD900A14
0x00000000
I get the same values with the mainline kernel and 4.17.
Brian
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-29 2:46 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-29 2:46 UTC (permalink / raw)
To: Jeffrey Hugo
Cc: Rob Herring, Jonathan Marek, Dave Airlie, MSM, Linus Walleij,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter,
freedreno-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW, Sean Paul
On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote:
> > > Do you know if the nexus 5 has a video or command mode panel? There
> > > is some glitchyness with vblanks and command mode panels.
> >
> > Its in command mode. I know this because I see two 'pp done time out'
> > messages, even on 4.17. Based on my understanding, the ping pong code is
> > only applicable for command mode panels.
>
> Actually, the ping pong element exists in both modes, but 'pp done
> time out' is a good indicator that it is command mode.
>
> Are you also seeing vblank timeouts?
Yes, here's a snippet of the first one.
[ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
[ 2.556020] [CRTC:49:crtc-0] vblank wait timed out
[ 2.556023] Modules linked in:
[ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426
[ 2.556038] Hardware name: Generic DT based system
[ 2.556056] Workqueue: events deferred_probe_work_func
...
> Do you have busybox?
>
> Can you run -
> sudo busybox devmem 0xFD900614
> sudo busybox devmem 0xFD900714
> sudo busybox devmem 0xFD900814
> sudo busybox devmem 0xFD900914
> sudo busybox devmem 0xFD900A14
# busybox devmem 0xFD900614
0x00020020
# busybox devmem 0xFD900714
0x00000000
# busybox devmem 0xFD900814
0x00000000
# busybox devmem 0xFD900914
0x00000000
# busybox devmem 0xFD900A14
0x00000000
I get the same values with the mainline kernel and 4.17.
Brian
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-29 1:17 ` Brian Masney
2019-05-29 1:32 ` Jeffrey Hugo
2019-05-29 2:14 ` Rob Clark
@ 2019-05-29 6:23 ` Linus Walleij
2019-05-29 9:41 ` Brian Masney
2 siblings, 1 reply; 35+ messages in thread
From: Linus Walleij @ 2019-05-29 6:23 UTC (permalink / raw)
To: Brian Masney
Cc: Rob Clark, Sean Paul, open list:DRM PANEL DRIVERS, MSM,
freedreno, Dave Airlie, Daniel Vetter, linux-kernel,
Jonathan Marek, Rob Herring
On Wed, May 29, 2019 at 3:17 AM Brian Masney <masneyb@onstation.org> wrote:
> It's in low speed mode but its usable.
How low speed is that?
> I assume that it's related to the
> vblank events not working properly?
They are only waiting for 50 ms before timing out, I raised it
to 100ms in the -next kernel. I'm still suspicious about this
even though I think you said this was not the problem.
For a command mode panel in LP mode it will nevertheless
be more than 100ms for sure, the update is visible to the
naked eye.
Raise it to 10000 ms or something and see what happens.
drivers/gpu/drm/drm_atomic_helper.c:
msecs_to_jiffies(50)
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-29 9:41 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-29 9:41 UTC (permalink / raw)
To: Linus Walleij
Cc: Rob Clark, Sean Paul, open list:DRM PANEL DRIVERS, MSM,
freedreno, Dave Airlie, Daniel Vetter, linux-kernel,
Jonathan Marek, Rob Herring
On Wed, May 29, 2019 at 08:23:17AM +0200, Linus Walleij wrote:
> On Wed, May 29, 2019 at 3:17 AM Brian Masney <masneyb@onstation.org> wrote:
>
> > It's in low speed mode but its usable.
>
> How low speed is that?
I don't have a number but my test with 4.17 is to run
'cat /etc/passwd > /dev/tty1' over a serial cable. The first 2-3 calls
will fill up the screen and the file contents appear to show up on the
screen immediately to the human eye. The next time that I run it
requires scrolling the entire console and there is a small fraction of
a second where I see the entire framebuffer contents scroll up. I
don't have a graphics background, but I believe that this is the
tearing effect that I'm seeing based on what I've read. I believe that
disp-te-gpios can be used to mitigate this tearing effect. I have a few
questions about this later once we get the basic display working.
> > I assume that it's related to the
> > vblank events not working properly?
>
> They are only waiting for 50 ms before timing out, I raised it
> to 100ms in the -next kernel. I'm still suspicious about this
> even though I think you said this was not the problem.
>
> For a command mode panel in LP mode it will nevertheless
> be more than 100ms for sure, the update is visible to the
> naked eye.
>
> Raise it to 10000 ms or something and see what happens.
> drivers/gpu/drm/drm_atomic_helper.c:
> msecs_to_jiffies(50)
I previously raised those timeouts as high as 5 seconds and it still
has the same issue. Writing to /dev/tty1 can take anywhere between a few
seconds to 30 seconds or more.
Brian
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-29 9:41 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-29 9:41 UTC (permalink / raw)
To: Linus Walleij
Cc: Sean Paul, Rob Herring, Jonathan Marek, Dave Airlie, MSM,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter,
freedreno-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW
On Wed, May 29, 2019 at 08:23:17AM +0200, Linus Walleij wrote:
> On Wed, May 29, 2019 at 3:17 AM Brian Masney <masneyb@onstation.org> wrote:
>
> > It's in low speed mode but its usable.
>
> How low speed is that?
I don't have a number but my test with 4.17 is to run
'cat /etc/passwd > /dev/tty1' over a serial cable. The first 2-3 calls
will fill up the screen and the file contents appear to show up on the
screen immediately to the human eye. The next time that I run it
requires scrolling the entire console and there is a small fraction of
a second where I see the entire framebuffer contents scroll up. I
don't have a graphics background, but I believe that this is the
tearing effect that I'm seeing based on what I've read. I believe that
disp-te-gpios can be used to mitigate this tearing effect. I have a few
questions about this later once we get the basic display working.
> > I assume that it's related to the
> > vblank events not working properly?
>
> They are only waiting for 50 ms before timing out, I raised it
> to 100ms in the -next kernel. I'm still suspicious about this
> even though I think you said this was not the problem.
>
> For a command mode panel in LP mode it will nevertheless
> be more than 100ms for sure, the update is visible to the
> naked eye.
>
> Raise it to 10000 ms or something and see what happens.
> drivers/gpu/drm/drm_atomic_helper.c:
> msecs_to_jiffies(50)
I previously raised those timeouts as high as 5 seconds and it still
has the same issue. Writing to /dev/tty1 can take anywhere between a few
seconds to 30 seconds or more.
Brian
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [Freedreno] [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-29 10:28 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-29 10:28 UTC (permalink / raw)
To: Jeffrey Hugo
Cc: Linus Walleij, Sean Paul, Rob Herring, Jonathan Marek,
Dave Airlie, MSM, linux-kernel, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter, freedreno
[-- Attachment #1: Type: text/plain, Size: 2022 bytes --]
On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote:
> On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote:
> >
> > On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote:
> > > > > Do you know if the nexus 5 has a video or command mode panel? There
> > > > > is some glitchyness with vblanks and command mode panels.
> > > >
> > > > Its in command mode. I know this because I see two 'pp done time out'
> > > > messages, even on 4.17. Based on my understanding, the ping pong code is
> > > > only applicable for command mode panels.
> > >
> > > Actually, the ping pong element exists in both modes, but 'pp done
> > > time out' is a good indicator that it is command mode.
> > >
> > > Are you also seeing vblank timeouts?
> >
> > Yes, here's a snippet of the first one.
> >
> > [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
> > [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out
> > [ 2.556023] Modules linked in:
> > [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426
> > [ 2.556038] Hardware name: Generic DT based system
> > [ 2.556056] Workqueue: events deferred_probe_work_func
> > ...
> >
> > > Do you have busybox?
> > >
> > > Can you run -
> > > sudo busybox devmem 0xFD900614
> > > sudo busybox devmem 0xFD900714
> > > sudo busybox devmem 0xFD900814
> > > sudo busybox devmem 0xFD900914
> > > sudo busybox devmem 0xFD900A14
> >
> > # busybox devmem 0xFD900614
> > 0x00020020
>
> Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1.
>
> Next one please:
>
> busybox devmem 0xFD912D30
It's 0x00000000 on mainline and 4.17. I used the following script to
dump the entire mdp5 memory region and attached the dump from 4.17 and
5.2rc1.
POS="0XFD900100"
while [ "${POS}" != "0XFD925000" ] ; do
echo -n "${POS} = "
busybox devmem "${POS}"
POS=$(printf '%#X' "$((${POS} + 4))")
done
Brian
[-- Attachment #2: mdp-memory-dump-4.17.txt.gz --]
[-- Type: application/gzip, Size: 102937 bytes --]
[-- Attachment #3: mdp-memory-dump-5.2rc1.txt.gz --]
[-- Type: application/gzip, Size: 103222 bytes --]
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-29 10:28 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-29 10:28 UTC (permalink / raw)
To: Jeffrey Hugo
Cc: Rob Herring, Jonathan Marek, Dave Airlie, MSM, Linus Walleij,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter,
freedreno-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW, Sean Paul
[-- Attachment #1: Type: text/plain, Size: 2048 bytes --]
On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote:
> On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb-1iNe0GrtECGEi8DpZVb4nw@public.gmane.org> wrote:
> >
> > On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote:
> > > > > Do you know if the nexus 5 has a video or command mode panel? There
> > > > > is some glitchyness with vblanks and command mode panels.
> > > >
> > > > Its in command mode. I know this because I see two 'pp done time out'
> > > > messages, even on 4.17. Based on my understanding, the ping pong code is
> > > > only applicable for command mode panels.
> > >
> > > Actually, the ping pong element exists in both modes, but 'pp done
> > > time out' is a good indicator that it is command mode.
> > >
> > > Are you also seeing vblank timeouts?
> >
> > Yes, here's a snippet of the first one.
> >
> > [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
> > [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out
> > [ 2.556023] Modules linked in:
> > [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426
> > [ 2.556038] Hardware name: Generic DT based system
> > [ 2.556056] Workqueue: events deferred_probe_work_func
> > ...
> >
> > > Do you have busybox?
> > >
> > > Can you run -
> > > sudo busybox devmem 0xFD900614
> > > sudo busybox devmem 0xFD900714
> > > sudo busybox devmem 0xFD900814
> > > sudo busybox devmem 0xFD900914
> > > sudo busybox devmem 0xFD900A14
> >
> > # busybox devmem 0xFD900614
> > 0x00020020
>
> Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1.
>
> Next one please:
>
> busybox devmem 0xFD912D30
It's 0x00000000 on mainline and 4.17. I used the following script to
dump the entire mdp5 memory region and attached the dump from 4.17 and
5.2rc1.
POS="0XFD900100"
while [ "${POS}" != "0XFD925000" ] ; do
echo -n "${POS} = "
busybox devmem "${POS}"
POS=$(printf '%#X' "$((${POS} + 4))")
done
Brian
[-- Attachment #2: mdp-memory-dump-4.17.txt.gz --]
[-- Type: application/gzip, Size: 102937 bytes --]
[-- Attachment #3: mdp-memory-dump-5.2rc1.txt.gz --]
[-- Type: application/gzip, Size: 103222 bytes --]
[-- Attachment #4: Type: text/plain, Size: 159 bytes --]
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [Freedreno] [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-29 10:28 ` Brian Masney
(?)
@ 2019-05-29 14:41 ` Jeffrey Hugo
2019-05-29 19:30 ` Brian Masney
-1 siblings, 1 reply; 35+ messages in thread
From: Jeffrey Hugo @ 2019-05-29 14:41 UTC (permalink / raw)
To: Brian Masney
Cc: Linus Walleij, Sean Paul, Rob Herring, Jonathan Marek,
Dave Airlie, MSM, linux-kernel, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter, freedreno
On Wed, May 29, 2019 at 4:28 AM Brian Masney <masneyb@onstation.org> wrote:
>
> On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote:
> > On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote:
> > >
> > > On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote:
> > > > > > Do you know if the nexus 5 has a video or command mode panel? There
> > > > > > is some glitchyness with vblanks and command mode panels.
> > > > >
> > > > > Its in command mode. I know this because I see two 'pp done time out'
> > > > > messages, even on 4.17. Based on my understanding, the ping pong code is
> > > > > only applicable for command mode panels.
> > > >
> > > > Actually, the ping pong element exists in both modes, but 'pp done
> > > > time out' is a good indicator that it is command mode.
> > > >
> > > > Are you also seeing vblank timeouts?
> > >
> > > Yes, here's a snippet of the first one.
> > >
> > > [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
> > > [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out
> > > [ 2.556023] Modules linked in:
> > > [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426
> > > [ 2.556038] Hardware name: Generic DT based system
> > > [ 2.556056] Workqueue: events deferred_probe_work_func
> > > ...
> > >
> > > > Do you have busybox?
> > > >
> > > > Can you run -
> > > > sudo busybox devmem 0xFD900614
> > > > sudo busybox devmem 0xFD900714
> > > > sudo busybox devmem 0xFD900814
> > > > sudo busybox devmem 0xFD900914
> > > > sudo busybox devmem 0xFD900A14
> > >
> > > # busybox devmem 0xFD900614
> > > 0x00020020
> >
> > Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1.
> >
> > Next one please:
> >
> > busybox devmem 0xFD912D30
>
> It's 0x00000000 on mainline and 4.17. I used the following script to
> dump the entire mdp5 memory region and attached the dump from 4.17 and
> 5.2rc1.
>
ok, 0 means autorefresh is not on. Which is fine. My next guess
would be the vblank code checking the hardware vblank counter, which
doesn't exist.
In video mode, there is a frame counter which increments, which can be
used as the vblank counter. Unfortunately, that hardware isn't active
in command mode, and there isn't an equivalent.
So, the vblank code is going to read the register, and look for an
update, which will never happen, thus it will timeout. There is a
backup path which uses timestamps (no hardware), which you can
activate with a quick hack - make max_vblank_count = 0 at the
following line
https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c#L753
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [Freedreno] [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-29 14:41 ` [Freedreno] " Jeffrey Hugo
@ 2019-05-29 19:30 ` Brian Masney
2019-05-29 19:58 ` Jeffrey Hugo
0 siblings, 1 reply; 35+ messages in thread
From: Brian Masney @ 2019-05-29 19:30 UTC (permalink / raw)
To: Jeffrey Hugo
Cc: Linus Walleij, Sean Paul, Rob Herring, Jonathan Marek,
Dave Airlie, MSM, linux-kernel, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter, freedreno
On Wed, May 29, 2019 at 08:41:31AM -0600, Jeffrey Hugo wrote:
> On Wed, May 29, 2019 at 4:28 AM Brian Masney <masneyb@onstation.org> wrote:
> >
> > On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote:
> > > On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote:
> > > >
> > > > On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote:
> > > > > > > Do you know if the nexus 5 has a video or command mode panel? There
> > > > > > > is some glitchyness with vblanks and command mode panels.
> > > > > >
> > > > > > Its in command mode. I know this because I see two 'pp done time out'
> > > > > > messages, even on 4.17. Based on my understanding, the ping pong code is
> > > > > > only applicable for command mode panels.
> > > > >
> > > > > Actually, the ping pong element exists in both modes, but 'pp done
> > > > > time out' is a good indicator that it is command mode.
> > > > >
> > > > > Are you also seeing vblank timeouts?
> > > >
> > > > Yes, here's a snippet of the first one.
> > > >
> > > > [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
> > > > [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out
> > > > [ 2.556023] Modules linked in:
> > > > [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426
> > > > [ 2.556038] Hardware name: Generic DT based system
> > > > [ 2.556056] Workqueue: events deferred_probe_work_func
> > > > ...
> > > >
> > > > > Do you have busybox?
> > > > >
> > > > > Can you run -
> > > > > sudo busybox devmem 0xFD900614
> > > > > sudo busybox devmem 0xFD900714
> > > > > sudo busybox devmem 0xFD900814
> > > > > sudo busybox devmem 0xFD900914
> > > > > sudo busybox devmem 0xFD900A14
> > > >
> > > > # busybox devmem 0xFD900614
> > > > 0x00020020
> > >
> > > Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1.
> > >
> > > Next one please:
> > >
> > > busybox devmem 0xFD912D30
> >
> > It's 0x00000000 on mainline and 4.17. I used the following script to
> > dump the entire mdp5 memory region and attached the dump from 4.17 and
> > 5.2rc1.
> >
>
> ok, 0 means autorefresh is not on. Which is fine. My next guess
> would be the vblank code checking the hardware vblank counter, which
> doesn't exist.
> In video mode, there is a frame counter which increments, which can be
> used as the vblank counter. Unfortunately, that hardware isn't active
> in command mode, and there isn't an equivalent.
>
> So, the vblank code is going to read the register, and look for an
> update, which will never happen, thus it will timeout. There is a
> backup path which uses timestamps (no hardware), which you can
> activate with a quick hack - make max_vblank_count = 0 at the
> following line
> https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c#L753
That fixed the issue!
I previously observed that mdp5_get_vblank_counter, specifically
mdp5_encoder_get_framecount, would always return 0.
What's the best way to fix this in mainline? Set that to zero if any
of the interface modes is MDP5_INTF_DSI_MODE_COMMAND?
Brian
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [Freedreno] [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
2019-05-29 19:30 ` Brian Masney
@ 2019-05-29 19:58 ` Jeffrey Hugo
2019-05-29 21:54 ` Brian Masney
0 siblings, 1 reply; 35+ messages in thread
From: Jeffrey Hugo @ 2019-05-29 19:58 UTC (permalink / raw)
To: Brian Masney, Jeffrey Hugo
Cc: Linus Walleij, Sean Paul, Rob Herring, Jonathan Marek,
Dave Airlie, MSM, linux-kernel, open list:DRM PANEL DRIVERS,
Rob Clark, Daniel Vetter, freedreno
On 5/29/2019 1:30 PM, Brian Masney wrote:
> On Wed, May 29, 2019 at 08:41:31AM -0600, Jeffrey Hugo wrote:
>> On Wed, May 29, 2019 at 4:28 AM Brian Masney <masneyb@onstation.org> wrote:
>>>
>>> On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote:
>>>> On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote:
>>>>>
>>>>> On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote:
>>>>>>>> Do you know if the nexus 5 has a video or command mode panel? There
>>>>>>>> is some glitchyness with vblanks and command mode panels.
>>>>>>>
>>>>>>> Its in command mode. I know this because I see two 'pp done time out'
>>>>>>> messages, even on 4.17. Based on my understanding, the ping pong code is
>>>>>>> only applicable for command mode panels.
>>>>>>
>>>>>> Actually, the ping pong element exists in both modes, but 'pp done
>>>>>> time out' is a good indicator that it is command mode.
>>>>>>
>>>>>> Are you also seeing vblank timeouts?
>>>>>
>>>>> Yes, here's a snippet of the first one.
>>>>>
>>>>> [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
>>>>> [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out
>>>>> [ 2.556023] Modules linked in:
>>>>> [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426
>>>>> [ 2.556038] Hardware name: Generic DT based system
>>>>> [ 2.556056] Workqueue: events deferred_probe_work_func
>>>>> ...
>>>>>
>>>>>> Do you have busybox?
>>>>>>
>>>>>> Can you run -
>>>>>> sudo busybox devmem 0xFD900614
>>>>>> sudo busybox devmem 0xFD900714
>>>>>> sudo busybox devmem 0xFD900814
>>>>>> sudo busybox devmem 0xFD900914
>>>>>> sudo busybox devmem 0xFD900A14
>>>>>
>>>>> # busybox devmem 0xFD900614
>>>>> 0x00020020
>>>>
>>>> Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1.
>>>>
>>>> Next one please:
>>>>
>>>> busybox devmem 0xFD912D30
>>>
>>> It's 0x00000000 on mainline and 4.17. I used the following script to
>>> dump the entire mdp5 memory region and attached the dump from 4.17 and
>>> 5.2rc1.
>>>
>>
>> ok, 0 means autorefresh is not on. Which is fine. My next guess
>> would be the vblank code checking the hardware vblank counter, which
>> doesn't exist.
>> In video mode, there is a frame counter which increments, which can be
>> used as the vblank counter. Unfortunately, that hardware isn't active
>> in command mode, and there isn't an equivalent.
>>
>> So, the vblank code is going to read the register, and look for an
>> update, which will never happen, thus it will timeout. There is a
>> backup path which uses timestamps (no hardware), which you can
>> activate with a quick hack - make max_vblank_count = 0 at the
>> following line
>> https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c#L753
>
> That fixed the issue!
Awesome. I'm glad it was something simple.
>
> I previously observed that mdp5_get_vblank_counter, specifically
> mdp5_encoder_get_framecount, would always return 0.
>
> What's the best way to fix this in mainline? Set that to zero if any
> of the interface modes is MDP5_INTF_DSI_MODE_COMMAND?
>
Short version, yes. Long version:
I still have that hack in my tree and haven't come back to formulating
a proper fix yet. Feel free to run with it.
Thinking about it briefly, we could do two things. We could fake a
hardware counter by just increment an int every time the vblank irq is
processed, but that seems clunky. Otherwise, we could force a
fallback onto the timestamp solution, which seems less invasive.
In theory, we could service multiple displays, with different
properties (ie a combination of command and video mode). The hack
then, is not good, because it would break video mode (at-least we
wouldn't be using the register when we could). It would be great if
the use of the hardware register could be done per display.
Luckily, it looks like someone just made that possible -
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/gpu/drm/drm_vblank.c?h=v5.2-rc2&id=ed20151a7699bb2c77eba3610199789a126940c4
--
Jeffrey Hugo
Qualcomm Datacenter Technologies as an affiliate of Qualcomm
Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [Freedreno] [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-29 21:54 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-29 21:54 UTC (permalink / raw)
To: Jeffrey Hugo
Cc: Jeffrey Hugo, Linus Walleij, Sean Paul, Rob Herring,
Jonathan Marek, Dave Airlie, MSM, linux-kernel,
open list:DRM PANEL DRIVERS, Rob Clark, Daniel Vetter, freedreno
On Wed, May 29, 2019 at 01:58:16PM -0600, Jeffrey Hugo wrote:
> On 5/29/2019 1:30 PM, Brian Masney wrote:
> > On Wed, May 29, 2019 at 08:41:31AM -0600, Jeffrey Hugo wrote:
> > > On Wed, May 29, 2019 at 4:28 AM Brian Masney <masneyb@onstation.org> wrote:
> > > >
> > > > On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote:
> > > > > On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote:
> > > > > >
> > > > > > On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote:
> > > > > > > > > Do you know if the nexus 5 has a video or command mode panel? There
> > > > > > > > > is some glitchyness with vblanks and command mode panels.
> > > > > > > >
> > > > > > > > Its in command mode. I know this because I see two 'pp done time out'
> > > > > > > > messages, even on 4.17. Based on my understanding, the ping pong code is
> > > > > > > > only applicable for command mode panels.
> > > > > > >
> > > > > > > Actually, the ping pong element exists in both modes, but 'pp done
> > > > > > > time out' is a good indicator that it is command mode.
> > > > > > >
> > > > > > > Are you also seeing vblank timeouts?
> > > > > >
> > > > > > Yes, here's a snippet of the first one.
> > > > > >
> > > > > > [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
> > > > > > [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out
> > > > > > [ 2.556023] Modules linked in:
> > > > > > [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426
> > > > > > [ 2.556038] Hardware name: Generic DT based system
> > > > > > [ 2.556056] Workqueue: events deferred_probe_work_func
> > > > > > ...
> > > > > >
> > > > > > > Do you have busybox?
> > > > > > >
> > > > > > > Can you run -
> > > > > > > sudo busybox devmem 0xFD900614
> > > > > > > sudo busybox devmem 0xFD900714
> > > > > > > sudo busybox devmem 0xFD900814
> > > > > > > sudo busybox devmem 0xFD900914
> > > > > > > sudo busybox devmem 0xFD900A14
> > > > > >
> > > > > > # busybox devmem 0xFD900614
> > > > > > 0x00020020
> > > > >
> > > > > Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1.
> > > > >
> > > > > Next one please:
> > > > >
> > > > > busybox devmem 0xFD912D30
> > > >
> > > > It's 0x00000000 on mainline and 4.17. I used the following script to
> > > > dump the entire mdp5 memory region and attached the dump from 4.17 and
> > > > 5.2rc1.
> > > >
> > >
> > > ok, 0 means autorefresh is not on. Which is fine. My next guess
> > > would be the vblank code checking the hardware vblank counter, which
> > > doesn't exist.
> > > In video mode, there is a frame counter which increments, which can be
> > > used as the vblank counter. Unfortunately, that hardware isn't active
> > > in command mode, and there isn't an equivalent.
> > >
> > > So, the vblank code is going to read the register, and look for an
> > > update, which will never happen, thus it will timeout. There is a
> > > backup path which uses timestamps (no hardware), which you can
> > > activate with a quick hack - make max_vblank_count = 0 at the
> > > following line
> > > https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c#L753
> >
> > That fixed the issue!
>
> Awesome. I'm glad it was something simple.
>
> >
> > I previously observed that mdp5_get_vblank_counter, specifically
> > mdp5_encoder_get_framecount, would always return 0.
> >
> > What's the best way to fix this in mainline? Set that to zero if any
> > of the interface modes is MDP5_INTF_DSI_MODE_COMMAND?
> >
>
> Short version, yes. Long version:
>
> I still have that hack in my tree and haven't come back to formulating
> a proper fix yet. Feel free to run with it.
>
> Thinking about it briefly, we could do two things. We could fake a
> hardware counter by just increment an int every time the vblank irq is
> processed, but that seems clunky. Otherwise, we could force a
> fallback onto the timestamp solution, which seems less invasive.
>
> In theory, we could service multiple displays, with different
> properties (ie a combination of command and video mode). The hack
> then, is not good, because it would break video mode (at-least we
> wouldn't be using the register when we could). It would be great if
> the use of the hardware register could be done per display.
>
> Luckily, it looks like someone just made that possible -
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/gpu/drm/drm_vblank.c?h=v5.2-rc2&id=ed20151a7699bb2c77eba3610199789a126940c4
I'll work on this for the msm driver.
Thanks for the info!
Brian
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support
@ 2019-05-29 21:54 ` Brian Masney
0 siblings, 0 replies; 35+ messages in thread
From: Brian Masney @ 2019-05-29 21:54 UTC (permalink / raw)
To: Jeffrey Hugo
Cc: Rob Herring, Jonathan Marek, Jeffrey Hugo, Dave Airlie, MSM,
Linus Walleij, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
open list:DRM PANEL DRIVERS, Rob Clark, Daniel Vetter, freedreno,
Sean Paul
On Wed, May 29, 2019 at 01:58:16PM -0600, Jeffrey Hugo wrote:
> On 5/29/2019 1:30 PM, Brian Masney wrote:
> > On Wed, May 29, 2019 at 08:41:31AM -0600, Jeffrey Hugo wrote:
> > > On Wed, May 29, 2019 at 4:28 AM Brian Masney <masneyb@onstation.org> wrote:
> > > >
> > > > On Tue, May 28, 2019 at 08:53:49PM -0600, Jeffrey Hugo wrote:
> > > > > On Tue, May 28, 2019 at 8:46 PM Brian Masney <masneyb@onstation.org> wrote:
> > > > > >
> > > > > > On Tue, May 28, 2019 at 07:42:19PM -0600, Jeffrey Hugo wrote:
> > > > > > > > > Do you know if the nexus 5 has a video or command mode panel? There
> > > > > > > > > is some glitchyness with vblanks and command mode panels.
> > > > > > > >
> > > > > > > > Its in command mode. I know this because I see two 'pp done time out'
> > > > > > > > messages, even on 4.17. Based on my understanding, the ping pong code is
> > > > > > > > only applicable for command mode panels.
> > > > > > >
> > > > > > > Actually, the ping pong element exists in both modes, but 'pp done
> > > > > > > time out' is a good indicator that it is command mode.
> > > > > > >
> > > > > > > Are you also seeing vblank timeouts?
> > > > > >
> > > > > > Yes, here's a snippet of the first one.
> > > > > >
> > > > > > [ 2.556014] WARNING: CPU: 0 PID: 5 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x288/0x290
> > > > > > [ 2.556020] [CRTC:49:crtc-0] vblank wait timed out
> > > > > > [ 2.556023] Modules linked in:
> > > > > > [ 2.556034] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.2.0-rc1-00178-g72c3c1fd5f86-dirty #426
> > > > > > [ 2.556038] Hardware name: Generic DT based system
> > > > > > [ 2.556056] Workqueue: events deferred_probe_work_func
> > > > > > ...
> > > > > >
> > > > > > > Do you have busybox?
> > > > > > >
> > > > > > > Can you run -
> > > > > > > sudo busybox devmem 0xFD900614
> > > > > > > sudo busybox devmem 0xFD900714
> > > > > > > sudo busybox devmem 0xFD900814
> > > > > > > sudo busybox devmem 0xFD900914
> > > > > > > sudo busybox devmem 0xFD900A14
> > > > > >
> > > > > > # busybox devmem 0xFD900614
> > > > > > 0x00020020
> > > > >
> > > > > Ok, so CTL_0 path, command mode, ping pong 0, with the output going to DSI 1.
> > > > >
> > > > > Next one please:
> > > > >
> > > > > busybox devmem 0xFD912D30
> > > >
> > > > It's 0x00000000 on mainline and 4.17. I used the following script to
> > > > dump the entire mdp5 memory region and attached the dump from 4.17 and
> > > > 5.2rc1.
> > > >
> > >
> > > ok, 0 means autorefresh is not on. Which is fine. My next guess
> > > would be the vblank code checking the hardware vblank counter, which
> > > doesn't exist.
> > > In video mode, there is a frame counter which increments, which can be
> > > used as the vblank counter. Unfortunately, that hardware isn't active
> > > in command mode, and there isn't an equivalent.
> > >
> > > So, the vblank code is going to read the register, and look for an
> > > update, which will never happen, thus it will timeout. There is a
> > > backup path which uses timestamps (no hardware), which you can
> > > activate with a quick hack - make max_vblank_count = 0 at the
> > > following line
> > > https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c#L753
> >
> > That fixed the issue!
>
> Awesome. I'm glad it was something simple.
>
> >
> > I previously observed that mdp5_get_vblank_counter, specifically
> > mdp5_encoder_get_framecount, would always return 0.
> >
> > What's the best way to fix this in mainline? Set that to zero if any
> > of the interface modes is MDP5_INTF_DSI_MODE_COMMAND?
> >
>
> Short version, yes. Long version:
>
> I still have that hack in my tree and haven't come back to formulating
> a proper fix yet. Feel free to run with it.
>
> Thinking about it briefly, we could do two things. We could fake a
> hardware counter by just increment an int every time the vblank irq is
> processed, but that seems clunky. Otherwise, we could force a
> fallback onto the timestamp solution, which seems less invasive.
>
> In theory, we could service multiple displays, with different
> properties (ie a combination of command and video mode). The hack
> then, is not good, because it would break video mode (at-least we
> wouldn't be using the register when we could). It would be great if
> the use of the hardware register could be done per display.
>
> Luckily, it looks like someone just made that possible -
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/gpu/drm/drm_vblank.c?h=v5.2-rc2&id=ed20151a7699bb2c77eba3610199789a126940c4
I'll work on this for the msm driver.
Thanks for the info!
Brian
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno
^ permalink raw reply [flat|nested] 35+ messages in thread
end of thread, other threads:[~2019-05-29 21:54 UTC | newest]
Thread overview: 35+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-09 2:03 [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support Brian Masney
2019-05-09 2:03 ` [PATCH v2 1/6] drm: msm: remove resv fields from msm_gem_object struct Brian Masney
2019-05-13 20:32 ` Bjorn Andersson
2019-05-13 22:25 ` Brian Masney
2019-05-09 2:03 ` [PATCH RFC v2 2/6] drm: msm: add dirty framebuffer helper Brian Masney
2019-05-09 2:03 ` [PATCH v2 3/6] ARM: qcom_defconfig: add display-related options Brian Masney
2019-05-09 2:03 ` Brian Masney
2019-05-09 2:03 ` [PATCH v2 4/6] ARM: dts: msm8974: add display support Brian Masney
2019-05-09 2:03 ` Brian Masney
2019-05-09 2:03 ` [PATCH v2 5/6] ARM: dts: qcom: msm8974-hammerhead: add support for backlight Brian Masney
2019-05-09 2:03 ` Brian Masney
2019-05-09 2:03 ` [PATCH v2 6/6] ARM: dts: qcom: msm8974-hammerhead: add support for display Brian Masney
2019-05-09 2:03 ` Brian Masney
2019-05-09 2:06 ` [PATCH RFC v2 0/6] ARM: qcom: initial Nexus 5 display support Brian Masney
2019-05-09 2:06 ` Brian Masney
2019-05-28 13:46 ` Linus Walleij
2019-05-29 1:17 ` Brian Masney
2019-05-29 1:32 ` [Freedreno] " Jeffrey Hugo
2019-05-29 1:32 ` Jeffrey Hugo
2019-05-29 1:37 ` [Freedreno] " Brian Masney
2019-05-29 1:42 ` Jeffrey Hugo
2019-05-29 2:46 ` Brian Masney
2019-05-29 2:46 ` Brian Masney
[not found] ` <CAOCk7NpC93ACr4jFm7SBOKSvFJSDhq2byX6BAYPX29BuYEkWnQ@mail.gmail.com>
2019-05-29 10:28 ` [Freedreno] " Brian Masney
2019-05-29 10:28 ` Brian Masney
2019-05-29 14:41 ` [Freedreno] " Jeffrey Hugo
2019-05-29 19:30 ` Brian Masney
2019-05-29 19:58 ` Jeffrey Hugo
2019-05-29 21:54 ` Brian Masney
2019-05-29 21:54 ` Brian Masney
2019-05-29 2:14 ` Rob Clark
2019-05-29 2:24 ` [Freedreno] " Jeffrey Hugo
2019-05-29 6:23 ` Linus Walleij
2019-05-29 9:41 ` Brian Masney
2019-05-29 9:41 ` Brian Masney
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.