[U-Boot] [PATCH V2 1/8] ARM: dts: imx: dh-imx6: Import DHCOM iMX6 PDK2 DTs from Linux

[U-Boot] [PATCH V2 1/8] ARM: dts: imx: dh-imx6: Import DHCOM iMX6 PDK2 DTs from Linux

[Marek Vasut]

Import DHCOM iMX6 PDK2 device tree from Linux 5.1.1 b724e9356404 .
Enable DT control in full U-Boot .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: No change
---
 arch/arm/dts/Makefile             |   3 +-
 arch/arm/dts/imx6q-dhcom-pdk2.dts | 151 ++++++++++
 arch/arm/dts/imx6q-dhcom-som.dtsi | 477 ++++++++++++++++++++++++++++++
 configs/dh_imx6_defconfig         |   3 +-
 4 files changed, 632 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/dts/imx6q-dhcom-pdk2.dts
 create mode 100644 arch/arm/dts/imx6q-dhcom-som.dtsi

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 0ec7bc987d..98db403c7b 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -586,7 +586,8 @@ dtb-$(CONFIG_MX6ULL) += \
 	imx6ull-dart-6ul.dtb
 
 dtb-$(CONFIG_ARCH_MX6) += \
-	imx6-colibri.dtb
+	imx6-colibri.dtb \
+	imx6q-dhcom-pdk2.dtb
 
 dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \
 	imx7d-sdb-qspi.dtb \
diff --git a/arch/arm/dts/imx6q-dhcom-pdk2.dts b/arch/arm/dts/imx6q-dhcom-pdk2.dts
new file mode 100644
index 0000000000..9c61e3be2d
--- /dev/null
+++ b/arch/arm/dts/imx6q-dhcom-pdk2.dts
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: (GPL-2.0+)
+/*
+ * Copyright (C) 2015 DH electronics GmbH
+ * Copyright (C) 2018 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+#include "imx6q-dhcom-som.dtsi"
+
+/ {
+	model = "Freescale i.MX6 Quad DHCOM Premium Developer Kit (2)";
+	compatible = "dh,imx6q-dhcom-pdk2", "dh,imx6q-dhcom-som", "fsl,imx6q";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_ext>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c2 {
+	sgtl5000: codec at a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clk_ext_audio_codec>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_base &pinctrl_hog>;
+
+	pinctrl_hog: hog-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x400120b0
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x400120b0
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x400120b0
+			MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03	0x400120b0
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x120b0
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20		0x400120b0
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27		0x120b0
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x120b0
+			MX6QDL_PAD_KEY_COL1__GPIO4_IO08		0x400120b0
+			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x400120b0
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x400120b0
+			MX6QDL_PAD_KEY_ROW1__GPIO4_IO09		0x400120b0
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x400120b0
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0x400120b0
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x400120b0
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x400120b0
+			MX6QDL_PAD_SD1_CMD__GPIO1_IO18		0x400120b0
+			MX6QDL_PAD_SD1_DAT0__GPIO1_IO16		0x400120b0
+			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x400120b0
+			MX6QDL_PAD_SD1_DAT2__GPIO1_IO19		0x400120b0
+			MX6QDL_PAD_SD1_CLK__GPIO1_IO20		0x400120b0
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x400120b0
+			MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x400120b0
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06		0x400120b0
+		>;
+	};
+
+	pinctrl_audmux_ext: audmux-ext-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_enet_1G: enet-1G-grp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x100b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x100b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x100b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x100b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x100b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x100b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x000b0
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x000b1
+			MX6QDL_PAD_EIM_D26__GPIO3_IO26		0x000b1
+		>;
+	};
+
+	pinctrl_pcie: pcie-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b1
+		>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&usdhc3 {
+	status = "okay";
+};
diff --git a/arch/arm/dts/imx6q-dhcom-som.dtsi b/arch/arm/dts/imx6q-dhcom-som.dtsi
new file mode 100644
index 0000000000..387801dde0
--- /dev/null
+++ b/arch/arm/dts/imx6q-dhcom-som.dtsi
@@ -0,0 +1,477 @@
+// SPDX-License-Identifier: (GPL-2.0+)
+/*
+ * Copyright (C) 2015 DH electronics GmbH
+ * Copyright (C) 2018 Marek Vasut <marex@denx.de>
+ */
+
+#include "imx6q.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc3;
+		mmc2 = &usdhc4;
+		mmc3 = &usdhc1;
+	};
+
+	memory at 10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_3p3v: regulator-3P3V {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio4 11 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash at 0 {	/* S25FL116K */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+		m25p,fast-read;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_100M>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy at 0 {	/* SMSC LAN8710Ai */
+			reg = <0>;
+			max-speed = <100>;
+			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+			reset-delay-us = <1000>;
+			reset-post-delay-us = <1000>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	ltc3676: pmic at 3c {
+		compatible = "lltc,ltc3676";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic_hw300>;
+		reg = <0x3c>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+
+		regulators {
+			sw1_reg: sw1 {
+				regulator-min-microvolt = <787500>;
+				regulator-max-microvolt = <1527272>;
+				lltc,fb-voltage-divider = <100000 110000>;
+				regulator-suspend-mem-microvolt = <1040000>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1885714>;
+				regulator-max-microvolt = <3657142>;
+				lltc,fb-voltage-divider = <100000 28000>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3_reg: sw3 {
+				regulator-min-microvolt = <787500>;
+				regulator-max-microvolt = <1527272>;
+				lltc,fb-voltage-divider = <100000 110000>;
+				regulator-suspend-mem-microvolt = <980000>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <855571>;
+				regulator-max-microvolt = <1659291>;
+				lltc,fb-voltage-divider = <100000 93100>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: ldo1 {
+				regulator-min-microvolt = <3240306>;
+				regulator-max-microvolt = <3240306>;
+				lltc,fb-voltage-divider = <102000 29400>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: ldo2 {
+				regulator-min-microvolt = <2484708>;
+				regulator-max-microvolt = <2484708>;
+				lltc,fb-voltage-divider = <100000 41200>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	touchscreen at 49 {	/* TSC2004 */
+		compatible = "ti,tsc2004";
+		reg = <0x49>;
+		vio-supply = <&reg_3p3v>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tsc2004_hw300>;
+		interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>;
+		status = "disabled";
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	rtc at 56 {
+		compatible = "rv3029c2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_hw300>;
+		reg = <0x56>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <12 2>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_base>;
+
+	pinctrl_hog_base: hog-base-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19		0x120b0
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06		0x120b0
+			MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x120b0
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x120b0
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21		0x120b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO	0x100b1
+			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK	0x100b1
+			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29	0x1b0b0
+		>;
+	};
+
+	pinctrl_enet_100M: enet-100M-grp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0x000b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x000b1
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x120b0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
+			MX6QDL_PAD_GPIO_8__FLEXCAN1_RX		0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX	0x1b0b0
+			MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_pmic_hw300: pmic-hw300-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1B0B0
+		>;
+	};
+
+	pinctrl_rtc_hw300: rtc-hw300-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x120B0
+		>;
+	};
+
+	pinctrl_tsc2004_hw300: tsc2004-hw300-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x120B0
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D20__UART1_RTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D19__UART1_CTS_B		0x4001b0b1
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x4001b0b1
+			MX6QDL_PAD_EIM_D24__GPIO3_IO24		0x4001b0b1
+			MX6QDL_PAD_EIM_D25__GPIO3_IO25		0x4001b0b1
+			MX6QDL_PAD_EIM_EB3__GPIO2_IO31		0x4001b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B	0x4001b0b1
+		>;
+	};
+
+	pinctrl_usbh1: usbh1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x120B0
+		>;
+	};
+
+	pinctrl_usbotg: usbotg-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x120B0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08		0x120B0
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+		>;
+	};
+};
+
+&reg_arm {
+	vin-supply = <&sw3_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&sw1_reg>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+	dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+	dcd-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	rng-gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	vbus-supply = <&reg_usb_h1_vbus>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
+	fsl,wp-controller;
+	keep-power-in-suspend;
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	non-removable;
+	bus-width = <8>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	status = "okay";
+};
diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig
index deec9f6bad..9aa08bfbcf 100644
--- a/configs/dh_imx6_defconfig
+++ b/configs/dh_imx6_defconfig
@@ -36,6 +36,8 @@ CONFIG_CMD_USB_MASS_STORAGE=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_TIME=y
 CONFIG_CMD_EXT4_WRITE=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6q-dhcom-pdk2"
 CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_DWC_AHSATA=y
 CONFIG_BOOTCOUNT_LIMIT=y
@@ -63,4 +65,3 @@ CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
 CONFIG_CI_UDC=y
 CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_IMX_WATCHDOG=y
-CONFIG_OF_LIBFDT=y
-- 
2.20.1

[U-Boot] [PATCH V2 2/8] ARM: dts: imx: dh-imx6: Fix SPI CS polarity on DHCOM iMX6 PDK2

[Marek Vasut]

The SPI nCS signal is active low, make it so.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: No change
---
 arch/arm/dts/imx6q-dhcom-som.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/dts/imx6q-dhcom-som.dtsi b/arch/arm/dts/imx6q-dhcom-som.dtsi
index 387801dde0..524cd287c6 100644
--- a/arch/arm/dts/imx6q-dhcom-som.dtsi
+++ b/arch/arm/dts/imx6q-dhcom-som.dtsi
@@ -61,7 +61,7 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio4 11 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio4 11 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
-- 
2.20.1

[U-Boot] [PATCH V2 3/8] ARM: imx: dh-imx6: Enable DM pin control

[Marek Vasut]

Enable DM pin control support on DHCOM iMX6 PDK2.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: No change
---
 configs/dh_imx6_defconfig | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig
index 9aa08bfbcf..e048fb2459 100644
--- a/configs/dh_imx6_defconfig
+++ b/configs/dh_imx6_defconfig
@@ -12,6 +12,7 @@ CONFIG_SPL=y
 CONFIG_SPL_SPI_FLASH_SUPPORT=y
 CONFIG_SPL_SPI_SUPPORT=y
 CONFIG_DISTRO_DEFAULTS=y
+# CONFIG_SYS_MALLOC_F is not set
 CONFIG_FIT=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
 CONFIG_BOOTDELAY=3
@@ -55,6 +56,8 @@ CONFIG_PHY_MICREL=y
 CONFIG_PHY_MICREL_KSZ90X1=y
 CONFIG_FEC_MXC=y
 CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
 CONFIG_SPI=y
 CONFIG_MXC_SPI=y
 CONFIG_USB=y
-- 
2.20.1

[U-Boot] [PATCH V2 4/8] ARM: imx: dh-imx6: Enable DM GPIO

[Marek Vasut]

Enable DM GPIO support on DHCOM iMX6 PDK2 and fix up board code
where applicable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: No change
---
 board/dhelectronics/dh_imx6/dh_imx6.c | 10 ++++++++++
 configs/dh_imx6_defconfig             |  1 +
 2 files changed, 11 insertions(+)

diff --git a/board/dhelectronics/dh_imx6/dh_imx6.c b/board/dhelectronics/dh_imx6/dh_imx6.c
index f9ac5c10e1..44f4ef8130 100644
--- a/board/dhelectronics/dh_imx6/dh_imx6.c
+++ b/board/dhelectronics/dh_imx6/dh_imx6.c
@@ -167,6 +167,9 @@ int board_eth_init(bd_t *bis)
 	struct mii_dev *bus = NULL;
 	struct phy_device *phydev = NULL;
 
+	gpio_request(IMX_GPIO_NR(5, 0), "PHY-reset");
+	gpio_request(IMX_GPIO_NR(1, 7), "VIO");
+
 	setup_fec_clock();
 
 	eth_phy_reset();
@@ -224,6 +227,8 @@ int board_mmc_init(bd_t *bis)
 	 * mmc1                    micro SD
 	 * mmc2                    eMMC
 	 */
+	gpio_request(USDHC2_CD_GPIO, "SD2-CD");
+	gpio_request(USDHC3_CD_GPIO, "SD3-CD");
 	gpio_direction_input(USDHC2_CD_GPIO);
 	gpio_direction_input(USDHC3_CD_GPIO);
 
@@ -244,6 +249,7 @@ int board_mmc_init(bd_t *bis)
 #ifdef CONFIG_USB_EHCI_MX6
 static void setup_usb(void)
 {
+	gpio_request(IMX_GPIO_NR(3, 31), "USB-VBUS");
 	/*
 	 * Set daisy chain for otg_pin_id on MX6Q.
 	 * For MX6DL, this bit is reserved.
@@ -379,6 +385,10 @@ static int board_get_hwcode(void)
 {
 	int hw_code;
 
+	gpio_request(HW_CODE_BIT_0, "HW-code-bit-0");
+	gpio_request(HW_CODE_BIT_1, "HW-code-bit-1");
+	gpio_request(HW_CODE_BIT_2, "HW-code-bit-2");
+
 	gpio_direction_input(HW_CODE_BIT_0);
 	gpio_direction_input(HW_CODE_BIT_1);
 	gpio_direction_input(HW_CODE_BIT_2);
diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig
index e048fb2459..9f6ebde777 100644
--- a/configs/dh_imx6_defconfig
+++ b/configs/dh_imx6_defconfig
@@ -43,6 +43,7 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_DWC_AHSATA=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_SYS_BOOTCOUNT_ADDR=0x00900000
+CONFIG_DM_GPIO=y
 CONFIG_FSL_ESDHC=y
 CONFIG_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
-- 
2.20.1

[U-Boot] [PATCH V2 5/8] ARM: imx: dh-imx6: Convert SD/MMC support to DM

[Marek Vasut]

Enable DM block and DM MMC support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: No change
---
 board/dhelectronics/dh_imx6/dh_imx6.c | 59 +--------------------------
 configs/dh_imx6_defconfig             |  1 +
 2 files changed, 3 insertions(+), 57 deletions(-)

diff --git a/board/dhelectronics/dh_imx6/dh_imx6.c b/board/dhelectronics/dh_imx6/dh_imx6.c
index 44f4ef8130..193bb0eade 100644
--- a/board/dhelectronics/dh_imx6/dh_imx6.c
+++ b/board/dhelectronics/dh_imx6/dh_imx6.c
@@ -6,6 +6,8 @@
  */
 
 #include <common.h>
+#include <dm.h>
+#include <dm/device-internal.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/crm_regs.h>
 #include <asm/arch/imx-regs.h>
@@ -189,63 +191,6 @@ int board_eth_init(bd_t *bis)
 }
 #endif
 
-#ifdef CONFIG_FSL_ESDHC
-
-#define USDHC2_CD_GPIO	IMX_GPIO_NR(6, 16)
-#define USDHC3_CD_GPIO	IMX_GPIO_NR(7, 8)
-
-static struct fsl_esdhc_cfg usdhc_cfg[3] = {
-	{ USDHC2_BASE_ADDR },
-	{ USDHC3_BASE_ADDR },
-	{ USDHC4_BASE_ADDR },
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-
-	switch (cfg->esdhc_base) {
-	case USDHC2_BASE_ADDR:
-		return gpio_get_value(USDHC2_CD_GPIO);
-	case USDHC3_BASE_ADDR:
-		return !gpio_get_value(USDHC3_CD_GPIO);
-	case USDHC4_BASE_ADDR:
-		return 1; /* eMMC/uSDHC4 is always present */
-	}
-
-	return 0;
-}
-
-int board_mmc_init(bd_t *bis)
-{
-	int i, ret;
-
-	/*
-	 * According to the board_mmc_init() the following map is done:
-	 * (U-Boot device node)    (Physical Port)
-	 * mmc0                    SD interface
-	 * mmc1                    micro SD
-	 * mmc2                    eMMC
-	 */
-	gpio_request(USDHC2_CD_GPIO, "SD2-CD");
-	gpio_request(USDHC3_CD_GPIO, "SD3-CD");
-	gpio_direction_input(USDHC2_CD_GPIO);
-	gpio_direction_input(USDHC3_CD_GPIO);
-
-	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-	usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
-
-	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
-		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
-		if (ret)
-			return ret;
-	}
-
-	return 0;
-}
-#endif
-
 #ifdef CONFIG_USB_EHCI_MX6
 static void setup_usb(void)
 {
diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig
index 9f6ebde777..839963290c 100644
--- a/configs/dh_imx6_defconfig
+++ b/configs/dh_imx6_defconfig
@@ -44,6 +44,7 @@ CONFIG_DWC_AHSATA=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_SYS_BOOTCOUNT_ADDR=0x00900000
 CONFIG_DM_GPIO=y
+CONFIG_DM_MMC=y
 CONFIG_FSL_ESDHC=y
 CONFIG_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
-- 
2.20.1

[U-Boot] [PATCH V2 6/8] ARM: imx: dh-imx6: Convert SATA support to DM

[Marek Vasut]

Enable DM SATA support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: Drop the ad-hoc sata binding, this is superseded by
    CONFIG_DWC_AHSATA_AHCI=y resp. drivers/ata/dwc_ahsata.c
---
 board/dhelectronics/dh_imx6/dh_imx6.c | 6 ++----
 configs/dh_imx6_defconfig             | 2 ++
 include/configs/dh_imx6.h             | 5 -----
 3 files changed, 4 insertions(+), 9 deletions(-)

diff --git a/board/dhelectronics/dh_imx6/dh_imx6.c b/board/dhelectronics/dh_imx6/dh_imx6.c
index 193bb0eade..737d9c6be3 100644
--- a/board/dhelectronics/dh_imx6/dh_imx6.c
+++ b/board/dhelectronics/dh_imx6/dh_imx6.c
@@ -20,6 +20,8 @@
 #include <asm/mach-imx/iomux-v3.h>
 #include <asm/mach-imx/mxc_i2c.h>
 #include <asm/mach-imx/sata.h>
+#include <ahci.h>
+#include <dwc_ahsata.h>
 #include <environment.h>
 #include <errno.h>
 #include <fsl_esdhc.h>
@@ -302,10 +304,6 @@ int board_init(void)
 	}
 #endif
 
-#ifdef CONFIG_SATA
-	setup_sata();
-#endif
-
 	setup_dhcom_mac_from_fuse();
 
 	return 0;
diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig
index 839963290c..dbb396a752 100644
--- a/configs/dh_imx6_defconfig
+++ b/configs/dh_imx6_defconfig
@@ -11,6 +11,7 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_SPL=y
 CONFIG_SPL_SPI_FLASH_SUPPORT=y
 CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_AHCI=y
 CONFIG_DISTRO_DEFAULTS=y
 # CONFIG_SYS_MALLOC_F is not set
 CONFIG_FIT=y
@@ -60,6 +61,7 @@ CONFIG_FEC_MXC=y
 CONFIG_MII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_SCSI=y
 CONFIG_SPI=y
 CONFIG_MXC_SPI=y
 CONFIG_USB=y
diff --git a/include/configs/dh_imx6.h b/include/configs/dh_imx6.h
index 3eee382a64..e68467dda3 100644
--- a/include/configs/dh_imx6.h
+++ b/include/configs/dh_imx6.h
@@ -63,12 +63,7 @@
 #define CONFIG_SYS_MMC_ENV_DEV		2 /* 1 = SDHC3, 2 = SDHC4 (eMMC) */
 
 /* SATA Configs */
-#ifdef CONFIG_CMD_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE	1
-#define CONFIG_DWC_AHSATA_PORT_ID	0
-#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
 #define CONFIG_LBA48
-#endif
 
 /* SPI Flash Configs */
 
-- 
2.20.1

[U-Boot] [PATCH V2 7/8] ARM: imx: dh-imx6: Convert USB support to DM

[Marek Vasut]

Enable DM USB host support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: No change
---
 configs/dh_imx6_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig
index dbb396a752..9418de10e7 100644
--- a/configs/dh_imx6_defconfig
+++ b/configs/dh_imx6_defconfig
@@ -65,6 +65,7 @@ CONFIG_DM_SCSI=y
 CONFIG_SPI=y
 CONFIG_MXC_SPI=y
 CONFIG_USB=y
+CONFIG_DM_USB=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_MANUFACTURER="dh"
 CONFIG_USB_GADGET_VENDOR_NUM=0x0525
-- 
2.20.1

[U-Boot] [PATCH V2 8/8] ARM: imx: dh-imx6: Convert SPI support to DM

[Marek Vasut]

Enable DM SPI and SF support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: No change
---
 board/dhelectronics/dh_imx6/dh_imx6.c | 10 ----------
 configs/dh_imx6_defconfig             |  4 ++++
 include/configs/dh_imx6.h             |  5 +++++
 3 files changed, 9 insertions(+), 10 deletions(-)

diff --git a/board/dhelectronics/dh_imx6/dh_imx6.c b/board/dhelectronics/dh_imx6/dh_imx6.c
index 737d9c6be3..50e3cb50a3 100644
--- a/board/dhelectronics/dh_imx6/dh_imx6.c
+++ b/board/dhelectronics/dh_imx6/dh_imx6.c
@@ -272,16 +272,6 @@ int board_early_init_f(void)
 	return 0;
 }
 
-#ifdef CONFIG_MXC_SPI
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
-	if (bus == 0 && cs == 0)
-		return IMX_GPIO_NR(2, 30);
-	else
-		return -1;
-}
-#endif
-
 int board_init(void)
 {
 	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig
index 9418de10e7..f2bb87132a 100644
--- a/configs/dh_imx6_defconfig
+++ b/configs/dh_imx6_defconfig
@@ -47,13 +47,16 @@ CONFIG_SYS_BOOTCOUNT_ADDR=0x00900000
 CONFIG_DM_GPIO=y
 CONFIG_DM_MMC=y
 CONFIG_FSL_ESDHC=y
+CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=25000000
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
 CONFIG_SPI_FLASH_GIGADEVICE=y
 CONFIG_SPI_FLASH_MACRONIX=y
 CONFIG_SPI_FLASH_SPANSION=y
 CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPI_FLASH_MTD=y
 CONFIG_PHYLIB=y
 CONFIG_PHY_MICREL=y
 CONFIG_PHY_MICREL_KSZ90X1=y
@@ -63,6 +66,7 @@ CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
 CONFIG_DM_SCSI=y
 CONFIG_SPI=y
+CONFIG_DM_SPI=y
 CONFIG_MXC_SPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
diff --git a/include/configs/dh_imx6.h b/include/configs/dh_imx6.h
index e68467dda3..3b1d0a99a1 100644
--- a/include/configs/dh_imx6.h
+++ b/include/configs/dh_imx6.h
@@ -66,6 +66,11 @@
 #define CONFIG_LBA48
 
 /* SPI Flash Configs */
+#if defined(CONFIG_SPL_BUILD)
+#undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
+#undef CONFIG_SPI_FLASH_MTD
+#endif
 
 /* UART */
 #define CONFIG_MXC_UART
-- 
2.20.1

[U-Boot] [PATCH V2 3/8] ARM: imx: dh-imx6: Enable DM pin control

[sbabic at denx.de]

> Enable DM pin control support on DHCOM iMX6 PDK2.
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Ludwig Zenz <lzenz@dh-electronics.com>
> Cc: Stefano Babic <sbabic@denx.de>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH V2 1/8] ARM: dts: imx: dh-imx6: Import DHCOM iMX6

[sbabic at denx.de]

> Import DHCOM iMX6 PDK2 device tree from Linux 5.1.1 b724e9356404 .
> Enable DT control in full U-Boot .
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Ludwig Zenz <lzenz@dh-electronics.com>
> Cc: Stefano Babic <sbabic@denx.de>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH V2 6/8] ARM: imx: dh-imx6: Convert SATA support to DM

[sbabic at denx.de]

> Enable DM SATA support on DHCOM iMX6 PDK2.
> Convert board code to match the DM support.
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Ludwig Zenz <lzenz@dh-electronics.com>
> Cc: Stefano Babic <sbabic@denx.de>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH V2 4/8] ARM: imx: dh-imx6: Enable DM GPIO

[sbabic at denx.de]

> Enable DM GPIO support on DHCOM iMX6 PDK2 and fix up board code
> where applicable.
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Ludwig Zenz <lzenz@dh-electronics.com>
> Cc: Stefano Babic <sbabic@denx.de>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH V2 8/8] ARM: imx: dh-imx6: Convert SPI support to DM

[sbabic at denx.de]

> Enable DM SPI and SF support on DHCOM iMX6 PDK2.
> Convert board code to match the DM support.
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Ludwig Zenz <lzenz@dh-electronics.com>
> Cc: Stefano Babic <sbabic@denx.de>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH V2 5/8] ARM: imx: dh-imx6: Convert SD/MMC support

[sbabic at denx.de]

> Enable DM block and DM MMC support on DHCOM iMX6 PDK2.
> Convert board code to match the DM support.
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Ludwig Zenz <lzenz@dh-electronics.com>
> Cc: Stefano Babic <sbabic@denx.de>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH V2 7/8] ARM: imx: dh-imx6: Convert USB support to DM

[sbabic at denx.de]

> Enable DM USB host support on DHCOM iMX6 PDK2.
> Convert board code to match the DM support.
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Ludwig Zenz <lzenz@dh-electronics.com>
> Cc: Stefano Babic <sbabic@denx.de>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH V2 2/8] ARM: dts: imx: dh-imx6: Fix SPI CS polarity

[sbabic at denx.de]

> The SPI nCS signal is active low, make it so.
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Ludwig Zenz <lzenz@dh-electronics.com>
> Cc: Stefano Babic <sbabic@denx.de>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================