[U-Boot] [PATCH v2 1/5] colibri_imx7: use UUID for rootfs

[U-Boot] [PATCH v2 1/5] colibri_imx7: use UUID for rootfs

[Igor Opaniuk]

From: Igor Opaniuk <igor.opaniuk@toradex.com>

Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.

Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
---
 include/configs/colibri_imx7.h | 47 ++++++++++++++++++++--------------
 1 file changed, 28 insertions(+), 19 deletions(-)

diff --git a/include/configs/colibri_imx7.h b/include/configs/colibri_imx7.h
index 5a4b9801cb..8bc75aba59 100644
--- a/include/configs/colibri_imx7.h
+++ b/include/configs/colibri_imx7.h
@@ -51,14 +51,22 @@
 #define CONFIG_SERVERIP			192.168.10.1
 
 #define EMMC_BOOTCMD \
-	"emmcargs=ip=off root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait\0" \
-	"emmcboot=run setup; " \
+	"set_emmcargs=setenv emmcargs ip=off root=PARTUUID=${uuid} ro " \
+		"rootfstype=ext4 rootwait\0" \
+	"emmcboot=run setup; run emmcfinduuid; run set_emmcargs; " \
 		"setenv bootargs ${defargs} ${emmcargs} ${setupargs} " \
 		"${vidargs}; echo Booting from internal eMMC chip...; " \
 		"run m4boot && " \
-		"load mmc 0:1 ${fdt_addr_r} ${soc}-colibri-emmc-${fdt_board}.dtb && " \
-		"load mmc 0:1 ${kernel_addr_r} ${boot_file} && " \
-		"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0"
+		"load mmc ${emmcdev}:${emmcbootpart} ${fdt_addr_r} " \
+		"${soc}-colibri-emmc-${fdt_board}.dtb && " \
+		"load mmc ${emmcdev}:${emmcbootpart} ${kernel_addr_r} " \
+		"${boot_file} && run fdt_fixup && " \
+		"bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
+	"emmcbootpart=1\0" \
+	"emmcdev=0\0" \
+	"emmcfinduuid=part uuid mmc ${emmcdev}:${emmcrootpart} uuid\0" \
+	"emmcrootpart=2\0"
+
 
 #define MEM_LAYOUT_ENV_SETTINGS \
 	"bootm_size=0x10000000\0" \
@@ -69,24 +77,25 @@
 	"ramdisk_addr_r=0x82100000\0"
 
 #if defined(CONFIG_TARGET_COLIBRI_IMX7_NAND)
-#define SD_BOOTCMD \
-	"sdargs=root=/dev/mmcblk0p2 ro rootwait\0" \
-	"sdboot=run setup; setenv bootargs ${defargs} ${sdargs} " \
-	"${setupargs} ${vidargs}; echo Booting from MMC/SD card...; " \
-	"run m4boot && " \
-	"load mmc 0:1 ${kernel_addr_r} ${kernel_file} && " \
-	"load mmc 0:1 ${fdt_addr_r} ${soc}-colibri-${fdt_board}.dtb && " \
-	"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0"
+#define SD_BOOTDEV 0
 #elif defined(CONFIG_TARGET_COLIBRI_IMX7_EMMC)
+#define SD_BOOTDEV 1
+#endif
+
 #define SD_BOOTCMD \
-	"sdargs=root=/dev/mmcblk1p2 ro rootwait\0" \
-	"sdboot=run setup; setenv bootargs ${defargs} ${sdargs} " \
+	"set_sdargs=setenv sdargs root=PARTUUID=${uuid} ro rootwait\0" \
+	"sdboot=run setup; run sdfinduuid; run set_sdargs; " \
+	"setenv bootargs ${defargs} ${sdargs} " \
 	"${setupargs} ${vidargs}; echo Booting from MMC/SD card...; " \
 	"run m4boot && " \
-	"load mmc 1:1 ${kernel_addr_r} ${kernel_file} && " \
-	"load mmc 1:1 ${fdt_addr_r} ${soc}-colibri-${fdt_board}.dtb && " \
-	"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0"
-#endif
+	"load mmc ${sddev}:${sdbootpart} ${kernel_addr_r} ${kernel_file} && " \
+	"load mmc ${sddev}:${sdbootpart} ${fdt_addr_r} " \
+	"${soc}-colibri-${fdt_board}.dtb && " \
+	"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
+	"sdbootpart=1\0" \
+	"sddev=" __stringify(SD_BOOTDEV) "\0" \
+	"sdfinduuid=part uuid mmc ${sddev}:${sdrootpart} uuid\0" \
+	"sdrootpart=2\0"
 
 
 #define NFS_BOOTCMD \
-- 
2.17.1

[U-Boot] [PATCH v2 2/5] colibri-imx6ull: use UUID for rootfs

[Igor Opaniuk]

From: Igor Opaniuk <igor.opaniuk@toradex.com>

Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.

Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
---
 include/configs/colibri-imx6ull.h | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)

diff --git a/include/configs/colibri-imx6ull.h b/include/configs/colibri-imx6ull.h
index 7cf550cf9e..2ba0ce5b79 100644
--- a/include/configs/colibri-imx6ull.h
+++ b/include/configs/colibri-imx6ull.h
@@ -66,12 +66,17 @@
 		"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
 
 #define SD_BOOTCMD \
-	"sdargs=root=/dev/mmcblk0p2 ro rootwait\0" \
-	"sdboot=run setup; setenv bootargs ${defargs} ${sdargs} " \
+	"set_sdargs=setenv sdargs root=PARTUUID=${uuid} ro rootwait\0" \
+	"sdboot=run setup; run sdfinduuid; run set_sdargs; " \
+	"setenv bootargs ${defargs} ${sdargs} " \
 	"${setupargs} ${vidargs}; echo Booting from MMC/SD card...; " \
-	"load mmc 0:1 ${kernel_addr_r} ${kernel_file} && " \
-	"load mmc 0:1 ${fdt_addr_r} " FDT_FILE " && " \
+	"load mmc ${sddev}:${sdbootpart} ${kernel_addr_r} ${kernel_file} && " \
+	"load mmc ${sddev}:${sdbootpart} ${fdt_addr_r} " FDT_FILE " && " \
 	"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
+	"sdbootpart=1\0" \
+	"sddev=0\0" \
+	"sdfinduuid=part uuid mmc ${sddev}:${sdrootpart} uuid\0" \
+	"sdrootpart=2\0"
 
 #define UBI_BOOTCMD \
 	"ubiargs=ubi.mtd=ubi root=ubi0:rootfs rw rootfstype=ubifs " \
-- 
2.17.1

[U-Boot] [PATCH v2 3/5] colibri_vf: use UUID for rootfs

[Igor Opaniuk]

From: Igor Opaniuk <igor.opaniuk@toradex.com>

Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.

Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
---
 include/configs/colibri_vf.h | 15 +++++++++++----
 1 file changed, 11 insertions(+), 4 deletions(-)

diff --git a/include/configs/colibri_vf.h b/include/configs/colibri_vf.h
index 0d57e303a1..da9a8426ec 100644
--- a/include/configs/colibri_vf.h
+++ b/include/configs/colibri_vf.h
@@ -68,12 +68,19 @@
 	"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
 
 #define SD_BOOTCMD \
-	"sdargs=root=/dev/mmcblk0p2 ro rootwait\0"	\
-	"sdboot=run setup; setenv bootargs ${defargs} ${sdargs} ${mtdparts} " \
+	"set_sdargs=setenv sdargs root=PARTUUID=${uuid} ro rootwait\0"	\
+	"sdboot=run setup; run sdfinduuid; run set_sdargs; " \
+	"setenv bootargs ${defargs} ${sdargs} ${mtdparts} " \
 	"${setupargs} ${vidargs}; echo Booting from MMC/SD card...; " \
-	"load mmc 0:1 ${kernel_addr_r} ${kernel_file} && " \
-	"load mmc 0:1 ${fdt_addr_r} ${soc}-colibri-${fdt_board}.dtb && " \
+	"load mmc ${sddev}:${sdbootpart} ${kernel_addr_r} ${kernel_file} && " \
+	"load mmc ${sddev}:${sdbootpart} ${fdt_addr_r} " \
+		"${soc}-colibri-${fdt_board}.dtb && " \
 	"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
+	"sdbootpart=1\0" \
+	"sddev=0\0" \
+	"sdfinduuid=part uuid mmc ${sddev}:${sdrootpart} uuid\0" \
+	"sdrootpart=2\0"
+
 
 #define UBI_BOOTCMD \
 	"ubiargs=ubi.mtd=ubi root=ubi0:rootfs rootfstype=ubifs " \
-- 
2.17.1

[U-Boot] [PATCH v2 4/5] apalis_imx6: use UUID for rootfs

[Igor Opaniuk]

From: Igor Opaniuk <igor.opaniuk@toradex.com>

1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).

Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
---
 include/configs/apalis_imx6.h | 64 +++++++++++++++++++++++------------
 1 file changed, 43 insertions(+), 21 deletions(-)

diff --git a/include/configs/apalis_imx6.h b/include/configs/apalis_imx6.h
index 96169f55f0..4f0f7b5129 100644
--- a/include/configs/apalis_imx6.h
+++ b/include/configs/apalis_imx6.h
@@ -125,16 +125,21 @@
 	"imx6q-apalis-cam-eval.dtb fat 0 1"
 
 #define EMMC_BOOTCMD \
-	"emmcargs=ip=off root=/dev/mmcblk0p2 rw,noatime rootfstype=ext4 " \
-		"rootwait\0" \
-	"emmcboot=run setup; " \
+	"set_emmcargs emmcargs ip=off root=PARTUUID=${uuid} ro,noatime " \
+		"rootfstype=ext4 rootwait\0" \
+	"emmcboot=run setup; run emmcfinduuid; run set_emmcargs; " \
 		"setenv bootargs ${defargs} ${emmcargs} ${setupargs} " \
 		"${vidargs}; echo Booting from internal eMMC chip...; "	\
-		"run emmcdtbload; load mmc 0:1 ${kernel_addr_r} " \
-		"${boot_file} && run fdt_fixup && " \
+		"run emmcdtbload; load mmc ${emmcdev}:${emmcbootpart} " \
+		"${kernel_addr_r} ${boot_file} && run fdt_fixup && " \
 		"bootz ${kernel_addr_r} ${dtbparam}\0" \
-	"emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} " \
-		"${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+	"emmcbootpart=1\0" \
+	"emmcdev=0\0" \
+	"emmcdtbload=setenv dtbparam; load mmc ${emmcdev}:${emmcbootpart} " \
+		"${fdt_addr_r} ${fdt_file} && " \
+		"setenv dtbparam \" - ${fdt_addr_r}\" && true\0" \
+	"emmcfinduuid=part uuid mmc ${mmcdev}:${emmcrootpart} uuid\0" \
+	"emmcrootpart=2\0"
 
 #define MEM_LAYOUT_ENV_SETTINGS \
 	"bootm_size=0x20000000\0" \
@@ -147,7 +152,7 @@
 	"scriptaddr=0x17000000\0"
 
 #define NFS_BOOTCMD \
-	"nfsargs=ip=:::::eth0:on root=/dev/nfs rw\0" \
+	"nfsargs=ip=:::::eth0:on root=/dev/nfs ro\0" \
 	"nfsboot=run setup; " \
 		"setenv bootargs ${defargs} ${nfsargs} ${setupargs} " \
 		"${vidargs}; echo Booting via DHCP/TFTP/NFS...; " \
@@ -157,27 +162,43 @@
 		"&& setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
 
 #define SD_BOOTCMD \
-	"sdargs=ip=off root=/dev/mmcblk1p2 rw,noatime rootfstype=ext4 " \
-		"rootwait\0" \
-	"sdboot=run setup; " \
+	"set_sdargs=setenv sdargs ip=off root=PARTUUID=${uuid} ro,noatime " \
+		"rootfstype=ext4 rootwait\0" \
+	"sdboot=run setup; run sdfinduuid; run set_sdargs; " \
 		"setenv bootargs ${defargs} ${sdargs} ${setupargs} " \
 		"${vidargs}; echo Booting from SD card; " \
-		"run sddtbload; load mmc 1:1 ${kernel_addr_r} " \
-		"${boot_file} && run fdt_fixup && " \
+		"run sddtbload; load mmc ${sddev}:${sdbootpart} " \
+		"${kernel_addr_r} ${boot_file} && run fdt_fixup && " \
 		"bootz ${kernel_addr_r} ${dtbparam}\0" \
-	"sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} " \
-		"${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+	"sdbootpart=1\0" \
+	"sddev=1\0" \
+	"sddtbload=setenv dtbparam; load mmc ${sddev}:${sdbootpart} " \
+		"${fdt_addr_r} " \
+		"${fdt_file} && setenv dtbparam \" - " \
+		"${fdt_addr_r}\" && true\0" \
+	"sdfinduuid=part uuid mmc ${sddev}:${sdrootpart} uuid\0" \
+	"sdrootpart=2\0"
+
 
 #define USB_BOOTCMD \
-	"usbargs=ip=off root=/dev/sda2 rw,noatime rootfstype=ext4 " \
-		"rootwait\0" \
-	"usbboot=run setup; setenv bootargs ${defargs} ${setupargs} " \
+	"set_usbargs=setenv usbargs ip=off root=PARTUUID=${uuid} ro,noatime " \
+		"rootfstype=ext4 rootwait\0" \
+	"usbboot=run setup; usb start; run usbfinduuid; run set_usbargs; " \
+		"setenv bootargs ${defargs} ${setupargs} " \
 		"${usbargs} ${vidargs}; echo Booting from USB stick...; " \
-		"usb start && run usbdtbload; load usb 0:1 ${kernel_addr_r} " \
+		"run usbdtbload; load usb " \
+		"${usbdev}:${usbbootpart} ${kernel_addr_r} " \
 		"${boot_file} && run fdt_fixup && " \
 		"bootz ${kernel_addr_r} ${dtbparam}\0" \
-	"usbdtbload=setenv dtbparam; load usb 0:1 ${fdt_addr_r} " \
-		"${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+	"usbbootpart=1\0" \
+	"usbdev=0\0" \
+	"usbdtbload=setenv dtbparam; load usb ${usbdev}:${usbbootpart} "\
+		"${fdt_addr_r} " \
+		"${fdt_file} && setenv dtbparam \" - " \
+		"${fdt_addr_r}\" && true\0" \
+	"usbfinduuid=part uuid usb ${usbdev}:${usbrootpart} uuid\0" \
+	"usbrootpart=2\0"
+
 
 #ifndef CONFIG_TDX_APALIS_IMX6_V1_0
 #define FDT_FILE "imx6q-apalis-eval.dtb"
@@ -201,6 +222,7 @@
 	MEM_LAYOUT_ENV_SETTINGS \
 	NFS_BOOTCMD \
 	SD_BOOTCMD \
+	USB_BOOTCMD \
 	"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
 		"00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \
 		"flash_eth.img && source ${loadaddr}\0" \
-- 
2.17.1

[U-Boot] [PATCH v2 5/5] apalis-tk1: use UUID for rootfs

[Igor Opaniuk]

From: Igor Opaniuk <igor.opaniuk@toradex.com>

1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).

Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
---
 include/configs/apalis-tk1.h | 62 ++++++++++++++++++++++++------------
 1 file changed, 41 insertions(+), 21 deletions(-)

diff --git a/include/configs/apalis-tk1.h b/include/configs/apalis-tk1.h
index 1d296ba51a..a026df8f50 100644
--- a/include/configs/apalis-tk1.h
+++ b/include/configs/apalis-tk1.h
@@ -51,15 +51,22 @@
 				"tegra124-apalis-eval.dtb fat 0 1 mmcpart 0"
 
 #define EMMC_BOOTCMD \
-	"emmcargs=ip=off root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait\0" \
-	"emmcboot=run setup; setenv bootargs ${defargs} ${emmcargs} " \
-		"${setupargs} ${vidargs}; echo Booting from internal eMMC " \
-		"chip...; run emmcdtbload; load mmc 0:1 ${kernel_addr_r} " \
+	"set_emmcargs=setenv emmcargs ip=off root=PARTUUID=${uuid} " \
+		"ro rootfstype=ext4 rootwait\0" \
+	"emmcboot=run setup; run emmcfinduuid; run set_emmcargs; " \
+		"setenv bootargs ${defargs} ${emmcargs} " \
+		"${setupargs} ${vidargs}; echo Booting from internal eMMC; " \
+		"run emmcdtbload; " \
+		"load mmc ${emmcdev}:${emmcbootpart} ${kernel_addr_r} " \
 		"${boot_file} && run fdt_fixup && " \
 		"bootm ${kernel_addr_r} - ${dtbparam}\0" \
-	"emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} " \
-		"${soc}-apalis-${fdt_board}.dtb && " \
-		"setenv dtbparam ${fdt_addr_r}\0"
+	"emmcbootpart=1\0" \
+	"emmcdev=0\0" \
+	"emmcdtbload=setenv dtbparam; load mmc ${emmcdev}:${emmcbootpart} " \
+		"${fdt_addr_r} ${soc}-apalis-${fdt_board}.dtb && " \
+		"setenv dtbparam ${fdt_addr_r}\0" \
+	"emmcfinduuid=part uuid mmc ${mmcdev}:${emmcrootpart} uuid\0" \
+	"emmcrootpart=2\0"
 
 #define NFS_BOOTCMD \
 	"nfsargs=ip=:::::eth0:on root=/dev/nfs rw\0" \
@@ -72,26 +79,38 @@
 		"&& setenv dtbparam ${fdt_addr_r}\0"
 
 #define SD_BOOTCMD \
-	"sdargs=ip=off root=/dev/mmcblk1p2 rw rootfstype=ext4 rootwait\0" \
-	"sdboot=run setup; setenv bootargs ${defargs} ${sdargs} ${setupargs} " \
+	"set_sdargs=setenv sdargs ip=off root=PARTUUID=${uuid} ro " \
+	"rootfstype=ext4 rootwait\0" \
+	"sdboot=run setup; run sdfinduuid; run set_sdargs; " \
+		"setenv bootargs ${defargs} ${sdargs} ${setupargs} " \
 		"${vidargs}; echo Booting from SD card in 8bit slot...; " \
-		"run sddtbload; load mmc 1:1 ${kernel_addr_r} " \
-		"${boot_file} && run fdt_fixup && " \
+		"run sddtbload; load mmc ${sddev}:${sdbootpart} " \
+		"${kernel_addr_r} ${boot_file} && run fdt_fixup && " \
 		"bootm ${kernel_addr_r} - ${dtbparam}\0" \
-	"sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} " \
-		"${soc}-apalis-${fdt_board}.dtb " \
-		"&& setenv dtbparam ${fdt_addr_r}\0"
+	"sdbootpart=1\0" \
+	"sddev=1\0" \
+	"sddtbload=setenv dtbparam; load mmc ${sddev}:${sdbootpart} " \
+		"${fdt_addr_r} ${soc}-apalis-${fdt_board}.dtb " \
+		"&& setenv dtbparam ${fdt_addr_r}\0" \
+	"sdfinduuid=part uuid mmc ${sddev}:${sdrootpart} uuid\0" \
+	"sdrootpart=2\0"
 
 #define USB_BOOTCMD \
-	"usbargs=ip=off root=/dev/sda2 rw rootfstype=ext4 rootwait\0" \
-	"usbboot=run setup; setenv bootargs ${defargs} ${setupargs} " \
+	"set_usbargs=setenv usbargs ip=off root=PARTUUID=${uuid} ro " \
+		"rootfstype=ext4 rootwait\0" \
+	"usbboot=run setup; usb start; run usbfinduuid; run set_usbargs; " \
+		"setenv bootargs ${defargs} ${setupargs} " \
 		"${usbargs} ${vidargs}; echo Booting from USB stick...; " \
-		"usb start && run usbdtbload; load usb 0:1 ${kernel_addr_r} " \
-		"${boot_file} && run fdt_fixup && " \
+		"run usbdtbload; load usb ${usbdev}:${usbbootpart} " \
+		"${kernel_addr_r} ${boot_file} && run fdt_fixup && " \
 		"bootm ${kernel_addr_r} - ${dtbparam}\0" \
-	"usbdtbload=setenv dtbparam; load usb 0:1 ${fdt_addr_r} " \
-		"${soc}-apalis-${fdt_board}.dtb " \
-		"&& setenv dtbparam ${fdt_addr_r}\0"
+	"usbbootpart=1\0" \
+	"usbdev=0\0" \
+	"usbdtbload=setenv dtbparam; load usb ${usbdev}:${usbbootpart} " \
+		"${fdt_addr_r} ${soc}-apalis-${fdt_board}.dtb " \
+		"&& setenv dtbparam ${fdt_addr_r}\0" \
+	"usbfinduuid=part uuid usb ${usbdev}:${usbrootpart} uuid\0" \
+	"usbrootpart=2\0"
 
 #define BOARD_EXTRA_ENV_SETTINGS \
 	"boot_file=uImage\0" \
@@ -104,6 +123,7 @@
 	"fdt_fixup=;\0" \
 	NFS_BOOTCMD \
 	SD_BOOTCMD \
+	USB_BOOTCMD \
 	"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
 		"00:14:2d:00:00:00; fi; pci enum && tftpboot ${loadaddr} " \
 		"flash_eth.img && source ${loadaddr}\0" \
-- 
2.17.1

[U-Boot] [PATCH v2 3/5] colibri_vf: use UUID for rootfs

[sbabic at denx.de]

> From: Igor Opaniuk <igor.opaniuk@toradex.com>
> Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
> partition. This fixes the issue, when MMC controllers are probed in
> a different order in U-boot and Linux kernel.
> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v2 2/5] colibri-imx6ull: use UUID for rootfs

[sbabic at denx.de]

> From: Igor Opaniuk <igor.opaniuk@toradex.com>
> Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
> partition. This fixes the issue, when MMC controllers are probed in
> a different order in U-boot and Linux kernel.
> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v2 1/5] colibri_imx7: use UUID for rootfs

[sbabic at denx.de]

> From: Igor Opaniuk <igor.opaniuk@toradex.com>
> Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
> partition. This fixes the issue, when MMC controllers are probed in
> a different order in U-boot and Linux kernel.
> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v2 5/5] apalis-tk1: use UUID for rootfs

[sbabic at denx.de]

> From: Igor Opaniuk <igor.opaniuk@toradex.com>
> 1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
> partition. This fixes the issue, when MMC controllers are probed in
> a different order in U-boot and Linux kernel.
> 2. Fix legacy USB command (both sdboot and usbboot can be used now).
> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v2 4/5] apalis_imx6: use UUID for rootfs

[sbabic at denx.de]

> From: Igor Opaniuk <igor.opaniuk@toradex.com>
> 1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
> partition. This fixes the issue, when MMC controllers are probed in
> a different order in U-boot and Linux kernel.
> 2. Fix legacy USB command (both sdboot and usbboot can be used now).
> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================