[PATCH net-next 01/10] dt-bindings: doc: net: keystone-netcp: document cpts

[Grygorii Strashko <grygorii.strashko@ti.com>]

The Keystone 2 66AK2HK/E/L 1G Ethernet Switch Subsystems contains The
Common Platform Time Sync (CPTS) module which is in general compatible with
CPTS module found on TI AM3/4/5 SoCs. So, the basic support for
Keystone 2 CPTS is available by default, but not documented.
The Keystone 2 CPTS module supports also some additional features like time
sync reference (RFTCLK) clock selection through CPTS_RFTCLK_SEL register
(offset: x08) in CPTS module, which is modelled as multiplexer clock.

This patch adds missed binding documentation for Keystone 2 66AK2HK/E/L
CPTS module.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
 .../bindings/net/keystone-netcp.txt           | 44 +++++++++++++++++++
 1 file changed, 44 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt
index 6262c2f293b0..24f11e042f8d 100644
--- a/Documentation/devicetree/bindings/net/keystone-netcp.txt
+++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt
@@ -104,6 +104,23 @@ Required properties:
 			- 10Gb mac<->mac forced mode : 11
 ----phy-handle:	phandle to PHY device
 
+- cpts:		sub-node time synchronization (CPTS) submodule configuration
+-- clocks:	CPTS reference clock. Should point on cpts-refclk-mux clock.
+-- clock-names: should be "cpts"
+-- cpts-refclk-mux: multiplexer clock definition sub-node for CPTS reference (RFTCLK) clock
+--- #clock-cells: should be 0
+--- clocks:	list of CPTS reference (RFTCLK) clock's parents as defined in Data manual
+--- ti,mux-tbl: array of multiplexer indexes as defined in Data manual
+--- assigned-clocks: should point on cpts-refclk-mux clock
+--- assigned-clock-parents: should point on required RFTCLK clock parent to be selected
+-- cpts_clock_mult: (optional) Numerator to convert input clock ticks
+		into nanoseconds
+-- cpts_clock_shift: (optional) Denominator to convert input clock ticks into
+		nanoseconds.
+		Mult and shift will be calculated basing on CPTS
+		rftclk frequency if both cpts_clock_shift and
+		cpts_clock_mult properties are not provided.
+
 Optional properties:
 - enable-ale:	NetCP driver keeps the address learning feature in the ethernet
 		switch module disabled. This attribute is to enable the address
@@ -168,6 +185,23 @@ netcp: netcp@2000000 {
 			tx-queue = <648>;
 			tx-channel = <8>;
 
+			cpts {
+				clocks = <&cpts_refclk_mux>;
+				clock-names = "cpts";
+
+				cpts_refclk_mux: cpts-refclk-mux {
+					#clock-cells = <0>;
+					clocks = <&chipclk12>, <&chipclk13>,
+						 <&timi0>, <&timi1>,
+						 <&tsipclka>, <&tsrefclk>,
+						 <&tsipclkb>;
+					ti,mux-tbl = <0x0>, <0x1>, <0x2>,
+						<0x3>, <0x4>, <0x8>, <0xC>;
+					assigned-clocks = <&cpts_refclk_mux>;
+					assigned-clock-parents = <&chipclk12>;
+				};
+			};
+
 			interfaces {
 				gbe0: interface-0 {
 					slave-port = <0>;
@@ -219,3 +253,13 @@ netcp: netcp@2000000 {
 		};
 	};
 };
+
+CPTS board configuration - select external CPTS RFTCLK:
+
+&tsrefclk{
+	clock-frequency = <500000000>;
+};
+
+&cpts_refclk_mux {
+	assigned-clock-parents = <&tsrefclk>;
+};
-- 
2.17.1