[PATCH 0/5] arch: riscv: add board and SoC DT file support

[PATCH 0/5] arch: riscv: add board and SoC DT file support

[Paul Walmsley]

Add support for building flattened DT files from DT source files under
arch/riscv/boot/dts.  Follow existing kernel precedent from other SoC
architectures.  Start our board support by adding initial support for
the SiFive FU540 SoC and the first development board that uses it, the
SiFive HiFive Unleashed A00.

This third version of the patch set adds I2C data for the chip,
incorporates all remaining changes that riscv-pk was making
automatically, and addresses a comment from Rob Herring
<robh@kernel.org>.

Boot-tested on v5.2-rc1 on a HiFive Unleashed A00 board, using the
BBL and open-source FSBL, with modifications to pass in the DTB
file generated by these patches.

This patch series can be found, along with the PRCI patch set
and the DT macro prerequisite patch, at:

https://github.com/sifive/riscv-linux/tree/dev/paulw/dts-v5.2-rc1


- Paul


Paul Walmsley (5):
  arch: riscv: add support for building DTB files from DT source data
  dt-bindings: riscv: sifive: add YAML documentation for the SiFive
    FU540
  dt-bindings: riscv: convert cpu binding to json-schema
  riscv: dts: add initial support for the SiFive FU540-C000 SoC
  riscv: dts: add initial board data for the SiFive HiFive Unleashed

 .../devicetree/bindings/riscv/cpus.yaml       | 168 ++++++++++++++
 .../devicetree/bindings/riscv/sifive.yaml     |  25 ++
 MAINTAINERS                                   |   9 +
 arch/riscv/boot/dts/Makefile                  |   2 +
 arch/riscv/boot/dts/sifive/Makefile           |   2 +
 arch/riscv/boot/dts/sifive/fu540-c000.dtsi    | 215 ++++++++++++++++++
 .../boot/dts/sifive/hifive-unleashed-a00.dts  |  67 ++++++
 7 files changed, 488 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/riscv/cpus.yaml
 create mode 100644 Documentation/devicetree/bindings/riscv/sifive.yaml
 create mode 100644 arch/riscv/boot/dts/Makefile
 create mode 100644 arch/riscv/boot/dts/sifive/Makefile
 create mode 100644 arch/riscv/boot/dts/sifive/fu540-c000.dtsi
 create mode 100644 arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts

-- 
2.20.1

[PATCH 0/5] arch: riscv: add board and SoC DT file support

[Paul Walmsley]

Add support for building flattened DT files from DT source files under
arch/riscv/boot/dts.  Follow existing kernel precedent from other SoC
architectures.  Start our board support by adding initial support for
the SiFive FU540 SoC and the first development board that uses it, the
SiFive HiFive Unleashed A00.

This third version of the patch set adds I2C data for the chip,
incorporates all remaining changes that riscv-pk was making
automatically, and addresses a comment from Rob Herring
<robh@kernel.org>.

Boot-tested on v5.2-rc1 on a HiFive Unleashed A00 board, using the
BBL and open-source FSBL, with modifications to pass in the DTB
file generated by these patches.

This patch series can be found, along with the PRCI patch set
and the DT macro prerequisite patch, at:

https://github.com/sifive/riscv-linux/tree/dev/paulw/dts-v5.2-rc1


- Paul


Paul Walmsley (5):
  arch: riscv: add support for building DTB files from DT source data
  dt-bindings: riscv: sifive: add YAML documentation for the SiFive
    FU540
  dt-bindings: riscv: convert cpu binding to json-schema
  riscv: dts: add initial support for the SiFive FU540-C000 SoC
  riscv: dts: add initial board data for the SiFive HiFive Unleashed

 .../devicetree/bindings/riscv/cpus.yaml       | 168 ++++++++++++++
 .../devicetree/bindings/riscv/sifive.yaml     |  25 ++
 MAINTAINERS                                   |   9 +
 arch/riscv/boot/dts/Makefile                  |   2 +
 arch/riscv/boot/dts/sifive/Makefile           |   2 +
 arch/riscv/boot/dts/sifive/fu540-c000.dtsi    | 215 ++++++++++++++++++
 .../boot/dts/sifive/hifive-unleashed-a00.dts  |  67 ++++++
 7 files changed, 488 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/riscv/cpus.yaml
 create mode 100644 Documentation/devicetree/bindings/riscv/sifive.yaml
 create mode 100644 arch/riscv/boot/dts/Makefile
 create mode 100644 arch/riscv/boot/dts/sifive/Makefile
 create mode 100644 arch/riscv/boot/dts/sifive/fu540-c000.dtsi
 create mode 100644 arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts

-- 
2.20.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH 1/5] arch: riscv: add support for building DTB files from DT source data

[Paul Walmsley]

Similar to ARM64, add support for building DTB files from DT source
data for RISC-V boards.

This patch starts with the infrastructure needed for SiFive boards.
Boards from other vendors would add support here in a similar form.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
---
 arch/riscv/boot/dts/Makefile | 2 ++
 1 file changed, 2 insertions(+)
 create mode 100644 arch/riscv/boot/dts/Makefile

diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
new file mode 100644
index 000000000000..dcc3ada78455
--- /dev/null
+++ b/arch/riscv/boot/dts/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+subdir-y += sifive
-- 
2.20.1

[PATCH 1/5] arch: riscv: add support for building DTB files from DT source data

[Paul Walmsley]

Similar to ARM64, add support for building DTB files from DT source
data for RISC-V boards.

This patch starts with the infrastructure needed for SiFive boards.
Boards from other vendors would add support here in a similar form.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
---
 arch/riscv/boot/dts/Makefile | 2 ++
 1 file changed, 2 insertions(+)
 create mode 100644 arch/riscv/boot/dts/Makefile

diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
new file mode 100644
index 000000000000..dcc3ada78455
--- /dev/null
+++ b/arch/riscv/boot/dts/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+subdir-y += sifive
-- 
2.20.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH 2/5] dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540

[Paul Walmsley]

Add YAML DT binding documentation for the SiFive FU540 SoC.  This
SoC is documented at:

    https://static.dev.sifive.com/FU540-C000-v1.0.pdf

Passes dt-doc-validate, as of yaml-bindings commit 4c79d42e9216.

This second version incorporates review feedback from Rob Herring
<robh@kernel.org>.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 .../devicetree/bindings/riscv/sifive.yaml     | 25 +++++++++++++++++++
 MAINTAINERS                                   |  9 +++++++
 2 files changed, 34 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/riscv/sifive.yaml

diff --git a/Documentation/devicetree/bindings/riscv/sifive.yaml b/Documentation/devicetree/bindings/riscv/sifive.yaml
new file mode 100644
index 000000000000..ce7ca191789e
--- /dev/null
+++ b/Documentation/devicetree/bindings/riscv/sifive.yaml
@@ -0,0 +1,25 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/riscv/sifive.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SiFive SoC-based boards
+
+maintainers:
+  - Paul Walmsley <paul.walmsley@sifive.com>
+  - Palmer Dabbelt <palmer@sifive.com>
+
+description:
+  SiFive SoC-based boards
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    items:
+      - enum:
+          - sifive,freedom-unleashed-a00
+      - const: sifive,fu540-c000
+      - const: sifive,fu540
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 5cfbea4ce575..8a64051cf5fc 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14322,6 +14322,15 @@ S:	Supported
 K:	sifive
 N:	sifive
 
+SIFIVE FU540 SYSTEM-ON-CHIP
+M:	Paul Walmsley <paul.walmsley@sifive.com>
+M:	Palmer Dabbelt <palmer@sifive.com>
+L:	linux-riscv@lists.infradead.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/pjw/sifive.git
+S:	Supported
+K:	fu540
+N:	fu540
+
 SILEAD TOUCHSCREEN DRIVER
 M:	Hans de Goede <hdegoede@redhat.com>
 L:	linux-input@vger.kernel.org
-- 
2.20.1

[PATCH 2/5] dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540

[Paul Walmsley]

Add YAML DT binding documentation for the SiFive FU540 SoC.  This
SoC is documented at:

    https://static.dev.sifive.com/FU540-C000-v1.0.pdf

Passes dt-doc-validate, as of yaml-bindings commit 4c79d42e9216.

This second version incorporates review feedback from Rob Herring
<robh@kernel.org>.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 .../devicetree/bindings/riscv/sifive.yaml     | 25 +++++++++++++++++++
 MAINTAINERS                                   |  9 +++++++
 2 files changed, 34 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/riscv/sifive.yaml

diff --git a/Documentation/devicetree/bindings/riscv/sifive.yaml b/Documentation/devicetree/bindings/riscv/sifive.yaml
new file mode 100644
index 000000000000..ce7ca191789e
--- /dev/null
+++ b/Documentation/devicetree/bindings/riscv/sifive.yaml
@@ -0,0 +1,25 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/riscv/sifive.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SiFive SoC-based boards
+
+maintainers:
+  - Paul Walmsley <paul.walmsley@sifive.com>
+  - Palmer Dabbelt <palmer@sifive.com>
+
+description:
+  SiFive SoC-based boards
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    items:
+      - enum:
+          - sifive,freedom-unleashed-a00
+      - const: sifive,fu540-c000
+      - const: sifive,fu540
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 5cfbea4ce575..8a64051cf5fc 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14322,6 +14322,15 @@ S:	Supported
 K:	sifive
 N:	sifive
 
+SIFIVE FU540 SYSTEM-ON-CHIP
+M:	Paul Walmsley <paul.walmsley@sifive.com>
+M:	Palmer Dabbelt <palmer@sifive.com>
+L:	linux-riscv@lists.infradead.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/pjw/sifive.git
+S:	Supported
+K:	fu540
+N:	fu540
+
 SILEAD TOUCHSCREEN DRIVER
 M:	Hans de Goede <hdegoede@redhat.com>
 L:	linux-input@vger.kernel.org
-- 
2.20.1

[PATCH 2/5] dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540

[Paul Walmsley]

Add YAML DT binding documentation for the SiFive FU540 SoC.  This
SoC is documented at:

    https://static.dev.sifive.com/FU540-C000-v1.0.pdf

Passes dt-doc-validate, as of yaml-bindings commit 4c79d42e9216.

This second version incorporates review feedback from Rob Herring
<robh@kernel.org>.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 .../devicetree/bindings/riscv/sifive.yaml     | 25 +++++++++++++++++++
 MAINTAINERS                                   |  9 +++++++
 2 files changed, 34 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/riscv/sifive.yaml

diff --git a/Documentation/devicetree/bindings/riscv/sifive.yaml b/Documentation/devicetree/bindings/riscv/sifive.yaml
new file mode 100644
index 000000000000..ce7ca191789e
--- /dev/null
+++ b/Documentation/devicetree/bindings/riscv/sifive.yaml
@@ -0,0 +1,25 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/riscv/sifive.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SiFive SoC-based boards
+
+maintainers:
+  - Paul Walmsley <paul.walmsley@sifive.com>
+  - Palmer Dabbelt <palmer@sifive.com>
+
+description:
+  SiFive SoC-based boards
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    items:
+      - enum:
+          - sifive,freedom-unleashed-a00
+      - const: sifive,fu540-c000
+      - const: sifive,fu540
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 5cfbea4ce575..8a64051cf5fc 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14322,6 +14322,15 @@ S:	Supported
 K:	sifive
 N:	sifive
 
+SIFIVE FU540 SYSTEM-ON-CHIP
+M:	Paul Walmsley <paul.walmsley@sifive.com>
+M:	Palmer Dabbelt <palmer@sifive.com>
+L:	linux-riscv@lists.infradead.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/pjw/sifive.git
+S:	Supported
+K:	fu540
+N:	fu540
+
 SILEAD TOUCHSCREEN DRIVER
 M:	Hans de Goede <hdegoede@redhat.com>
 L:	linux-input@vger.kernel.org
-- 
2.20.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH 3/5] dt-bindings: riscv: convert cpu binding to json-schema

[Paul Walmsley]

At Rob's request, we're starting to migrate our DT binding
documentation to json-schema YAML format.  Start by converting our cpu
binding documentation.  While doing so, document more properties and
nodes.  This includes adding binding documentation support for the E51
and U54 CPU cores ("harts") that are present on this SoC.  These cores
are described in:

    https://static.dev.sifive.com/FU540-C000-v1.0.pdf

This cpus.yaml file is intended to be a starting point and to
evolve over time.  It passes dt-doc-validate as of the yaml-bindings
commit 4c79d42e9216.

This patch was originally based on the ARM json-schema binding
documentation as added by commit 672951cbd1b7 ("dt-bindings: arm: Convert
cpu binding to json-schema").

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
---
 .../devicetree/bindings/riscv/cpus.yaml       | 168 ++++++++++++++++++
 1 file changed, 168 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/riscv/cpus.yaml

diff --git a/Documentation/devicetree/bindings/riscv/cpus.yaml b/Documentation/devicetree/bindings/riscv/cpus.yaml
new file mode 100644
index 000000000000..6e8d55d9d4e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/riscv/cpus.yaml
@@ -0,0 +1,168 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/riscv/cpus.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RISC-V bindings for 'cpus' DT nodes
+
+maintainers:
+  - Paul Walmsley <paul.walmsley@sifive.com>
+  - Palmer Dabbelt <palmer@sifive.com>
+
+allOf:
+  - $ref: /schemas/cpus.yaml#
+
+properties:
+  $nodename:
+    const: cpus
+    description: Container of cpu nodes
+
+  '#address-cells':
+    const: 1
+    description: |
+      A single unsigned 32-bit integer uniquely identifies each RISC-V
+      hart in a system.  (See the "reg" node under the "cpu" node,
+      below).
+
+  '#size-cells':
+    const: 0
+
+patternProperties:
+  '^cpu@[0-9a-f]+$':
+    properties:
+      compatible:
+        type: array
+        items:
+          - enum:
+              - sifive,rocket0
+              - sifive,e5
+              - sifive,e51
+              - sifive,u54-mc
+              - sifive,u54
+              - sifive,u5
+          - const: riscv
+        description:
+          Identifies that the hart uses the RISC-V instruction set
+          and identifies the type of the hart.
+
+      mmu-type:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/string"
+          - enum:
+              - riscv,sv32
+              - riscv,sv39
+              - riscv,sv48
+        description:
+          Identifies the MMU address translation mode used on this
+          hart.  These values originate from the RISC-V Privileged
+          Specification document, available from
+          https://riscv.org/specifications/
+
+      riscv,isa:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/string"
+          - enum:
+              - rv64imac
+              - rv64imafdc
+        description:
+          Identifies the specific RISC-V instruction set architecture
+          supported by the hart.  These are documented in the RISC-V
+          User-Level ISA document, available from
+          https://riscv.org/specifications/
+
+      timebase-frequency:
+        type: integer
+        minimum: 1
+        description:
+          Specifies the clock frequency of the system timer in Hz.
+          This value is common to all harts on a single system image.
+
+      interrupt-controller:
+        type: object
+        description: Describes the CPU's local interrupt controller
+
+        properties:
+          '#interrupt-cells':
+            const: 1
+
+          compatible:
+            const: riscv,cpu-intc
+
+          interrupt-controller: true
+
+        required:
+          - '#interrupt-cells'
+          - compatible
+          - interrupt-controller
+
+    required:
+      - riscv,isa
+      - timebase-frequency
+      - interrupt-controller
+
+examples:
+  - |
+    // Example 1: SiFive Freedom U540G Development Kit
+    cpus {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        timebase-frequency = <1000000>;
+        cpu@0 {
+                clock-frequency = <0>;
+                compatible = "sifive,rocket0", "riscv";
+                device_type = "cpu";
+                i-cache-block-size = <64>;
+                i-cache-sets = <128>;
+                i-cache-size = <16384>;
+                reg = <0>;
+                riscv,isa = "rv64imac";
+                cpu_intc0: interrupt-controller {
+                        #interrupt-cells = <1>;
+                        compatible = "riscv,cpu-intc";
+                        interrupt-controller;
+                };
+        };
+        cpu@1 {
+                clock-frequency = <0>;
+                compatible = "sifive,rocket0", "riscv";
+                d-cache-block-size = <64>;
+                d-cache-sets = <64>;
+                d-cache-size = <32768>;
+                d-tlb-sets = <1>;
+                d-tlb-size = <32>;
+                device_type = "cpu";
+                i-cache-block-size = <64>;
+                i-cache-sets = <64>;
+                i-cache-size = <32768>;
+                i-tlb-sets = <1>;
+                i-tlb-size = <32>;
+                mmu-type = "riscv,sv39";
+                reg = <1>;
+                riscv,isa = "rv64imafdc";
+                tlb-split;
+                cpu_intc1: interrupt-controller {
+                        #interrupt-cells = <1>;
+                        compatible = "riscv,cpu-intc";
+                        interrupt-controller;
+                };
+        };
+    };
+
+  - |
+    // Example 2: Spike ISA Simulator with 1 Hart
+    cpus {
+            cpu@0 {
+                    device_type = "cpu";
+                    reg = <0>;
+                    compatible = "riscv";
+                    riscv,isa = "rv64imafdc";
+                    mmu-type = "riscv,sv48";
+                    interrupt-controller {
+                            #interrupt-cells = <1>;
+                            interrupt-controller;
+                            compatible = "riscv,cpu-intc";
+                    };
+            };
+    };
+...
-- 
2.20.1

[PATCH 3/5] dt-bindings: riscv: convert cpu binding to json-schema

[Paul Walmsley]

At Rob's request, we're starting to migrate our DT binding
documentation to json-schema YAML format.  Start by converting our cpu
binding documentation.  While doing so, document more properties and
nodes.  This includes adding binding documentation support for the E51
and U54 CPU cores ("harts") that are present on this SoC.  These cores
are described in:

    https://static.dev.sifive.com/FU540-C000-v1.0.pdf

This cpus.yaml file is intended to be a starting point and to
evolve over time.  It passes dt-doc-validate as of the yaml-bindings
commit 4c79d42e9216.

This patch was originally based on the ARM json-schema binding
documentation as added by commit 672951cbd1b7 ("dt-bindings: arm: Convert
cpu binding to json-schema").

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
---
 .../devicetree/bindings/riscv/cpus.yaml       | 168 ++++++++++++++++++
 1 file changed, 168 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/riscv/cpus.yaml

diff --git a/Documentation/devicetree/bindings/riscv/cpus.yaml b/Documentation/devicetree/bindings/riscv/cpus.yaml
new file mode 100644
index 000000000000..6e8d55d9d4e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/riscv/cpus.yaml
@@ -0,0 +1,168 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/riscv/cpus.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RISC-V bindings for 'cpus' DT nodes
+
+maintainers:
+  - Paul Walmsley <paul.walmsley@sifive.com>
+  - Palmer Dabbelt <palmer@sifive.com>
+
+allOf:
+  - $ref: /schemas/cpus.yaml#
+
+properties:
+  $nodename:
+    const: cpus
+    description: Container of cpu nodes
+
+  '#address-cells':
+    const: 1
+    description: |
+      A single unsigned 32-bit integer uniquely identifies each RISC-V
+      hart in a system.  (See the "reg" node under the "cpu" node,
+      below).
+
+  '#size-cells':
+    const: 0
+
+patternProperties:
+  '^cpu@[0-9a-f]+$':
+    properties:
+      compatible:
+        type: array
+        items:
+          - enum:
+              - sifive,rocket0
+              - sifive,e5
+              - sifive,e51
+              - sifive,u54-mc
+              - sifive,u54
+              - sifive,u5
+          - const: riscv
+        description:
+          Identifies that the hart uses the RISC-V instruction set
+          and identifies the type of the hart.
+
+      mmu-type:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/string"
+          - enum:
+              - riscv,sv32
+              - riscv,sv39
+              - riscv,sv48
+        description:
+          Identifies the MMU address translation mode used on this
+          hart.  These values originate from the RISC-V Privileged
+          Specification document, available from
+          https://riscv.org/specifications/
+
+      riscv,isa:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/string"
+          - enum:
+              - rv64imac
+              - rv64imafdc
+        description:
+          Identifies the specific RISC-V instruction set architecture
+          supported by the hart.  These are documented in the RISC-V
+          User-Level ISA document, available from
+          https://riscv.org/specifications/
+
+      timebase-frequency:
+        type: integer
+        minimum: 1
+        description:
+          Specifies the clock frequency of the system timer in Hz.
+          This value is common to all harts on a single system image.
+
+      interrupt-controller:
+        type: object
+        description: Describes the CPU's local interrupt controller
+
+        properties:
+          '#interrupt-cells':
+            const: 1
+
+          compatible:
+            const: riscv,cpu-intc
+
+          interrupt-controller: true
+
+        required:
+          - '#interrupt-cells'
+          - compatible
+          - interrupt-controller
+
+    required:
+      - riscv,isa
+      - timebase-frequency
+      - interrupt-controller
+
+examples:
+  - |
+    // Example 1: SiFive Freedom U540G Development Kit
+    cpus {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        timebase-frequency = <1000000>;
+        cpu@0 {
+                clock-frequency = <0>;
+                compatible = "sifive,rocket0", "riscv";
+                device_type = "cpu";
+                i-cache-block-size = <64>;
+                i-cache-sets = <128>;
+                i-cache-size = <16384>;
+                reg = <0>;
+                riscv,isa = "rv64imac";
+                cpu_intc0: interrupt-controller {
+                        #interrupt-cells = <1>;
+                        compatible = "riscv,cpu-intc";
+                        interrupt-controller;
+                };
+        };
+        cpu@1 {
+                clock-frequency = <0>;
+                compatible = "sifive,rocket0", "riscv";
+                d-cache-block-size = <64>;
+                d-cache-sets = <64>;
+                d-cache-size = <32768>;
+                d-tlb-sets = <1>;
+                d-tlb-size = <32>;
+                device_type = "cpu";
+                i-cache-block-size = <64>;
+                i-cache-sets = <64>;
+                i-cache-size = <32768>;
+                i-tlb-sets = <1>;
+                i-tlb-size = <32>;
+                mmu-type = "riscv,sv39";
+                reg = <1>;
+                riscv,isa = "rv64imafdc";
+                tlb-split;
+                cpu_intc1: interrupt-controller {
+                        #interrupt-cells = <1>;
+                        compatible = "riscv,cpu-intc";
+                        interrupt-controller;
+                };
+        };
+    };
+
+  - |
+    // Example 2: Spike ISA Simulator with 1 Hart
+    cpus {
+            cpu@0 {
+                    device_type = "cpu";
+                    reg = <0>;
+                    compatible = "riscv";
+                    riscv,isa = "rv64imafdc";
+                    mmu-type = "riscv,sv48";
+                    interrupt-controller {
+                            #interrupt-cells = <1>;
+                            interrupt-controller;
+                            compatible = "riscv,cpu-intc";
+                    };
+            };
+    };
+...
-- 
2.20.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH 4/5] riscv: dts: add initial support for the SiFive FU540-C000 SoC

[Paul Walmsley]

Add initial support for the SiFive FU540-C000 SoC.  This is a 28nm SoC
based around the SiFive U54-MC core complex and a TileLink
interconnect.

This file is expected to grow as more device drivers are added to the
kernel.

This patch includes a fix to the QSPI memory map due to a
documentation bug, found by ShihPo Hung <shihpo.hung@sifive.com>, adds
entries for the I2C controller, and merges all DT changes that
formerly were made dynamically by the riscv-pk BBL proxy kernel.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: ShihPo Hung <shihpo.hung@sifive.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 arch/riscv/boot/dts/sifive/fu540-c000.dtsi | 215 +++++++++++++++++++++
 1 file changed, 215 insertions(+)
 create mode 100644 arch/riscv/boot/dts/sifive/fu540-c000.dtsi

diff --git a/arch/riscv/boot/dts/sifive/fu540-c000.dtsi b/arch/riscv/boot/dts/sifive/fu540-c000.dtsi
new file mode 100644
index 000000000000..3c06ee4b2b29
--- /dev/null
+++ b/arch/riscv/boot/dts/sifive/fu540-c000.dtsi
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2018-2019 SiFive, Inc */
+
+/dts-v1/;
+
+#include <dt-bindings/clock/sifive-fu540-prci.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	compatible = "sifive,fu540-c000", "sifive,fu540";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		timebase-frequency = <1000000>;
+		cpu0: cpu@0 {
+			compatible = "sifive,e51", "sifive,rocket0", "riscv";
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <128>;
+			i-cache-size = <16384>;
+			reg = <0>;
+			riscv,isa = "rv64imac";
+			status = "disabled";
+			cpu0_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+		cpu1: cpu@1 {
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <1>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			cpu1_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+		cpu2: cpu@2 {
+			clock-frequency = <0>;
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <2>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			cpu2_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+		cpu3: cpu@3 {
+			clock-frequency = <0>;
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <3>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			cpu3_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+		cpu4: cpu@4 {
+			clock-frequency = <0>;
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <4>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			cpu4_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+	};
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "sifive,fu540-c000", "sifive,fu540", "simple-bus";
+		ranges;
+		plic0: interrupt-controller@c000000 {
+			#interrupt-cells = <1>;
+			compatible = "sifive,plic-1.0.0";
+			reg = <0x0 0xc000000 0x0 0x4000000>;
+			riscv,ndev = <53>;
+			interrupt-controller;
+			interrupts-extended = <
+				&cpu0_intc 0xffffffff
+				&cpu1_intc 0xffffffff &cpu1_intc 9
+				&cpu2_intc 0xffffffff &cpu2_intc 9
+				&cpu3_intc 0xffffffff &cpu3_intc 9
+				&cpu4_intc 0xffffffff &cpu4_intc 9>;
+		};
+		prci: clock-controller@10000000 {
+			compatible = "sifive,fu540-c000-prci";
+			reg = <0x0 0x10000000 0x0 0x1000>;
+			clocks = <&hfclk>, <&rtcclk>;
+			#clock-cells = <1>;
+		};
+		uart0: serial@10010000 {
+			compatible = "sifive,fu540-c000-uart", "sifive,uart0";
+			reg = <0x0 0x10010000 0x0 0x1000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <4>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+		};
+		uart1: serial@10011000 {
+			compatible = "sifive,fu540-c000-uart", "sifive,uart0";
+			reg = <0x0 0x10011000 0x0 0x1000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <5>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+		};
+		i2c0: i2c@10030000 {
+			compatible = "sifive,fu540-c000-i2c", "sifive,i2c0";
+			reg = <0x0 0x10030000 0x0 0x1000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <50>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+			reg-shift = <2>;
+			reg-io-width = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		qspi0: spi@10040000 {
+			compatible = "sifive,fu540-c000-spi", "sifive,spi0";
+			reg = <0x0 0x10040000 0x0 0x1000
+			       0x0 0x20000000 0x0 0x10000000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <51>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		qspi1: spi@10041000 {
+			compatible = "sifive,fu540-c000-spi", "sifive,spi0";
+			reg = <0x0 0x10041000 0x0 0x1000
+			       0x0 0x30000000 0x0 0x10000000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <52>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		qspi2: spi@10050000 {
+			compatible = "sifive,fu540-c000-spi", "sifive,spi0";
+			reg = <0x0 0x10050000 0x0 0x1000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <6>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
-- 
2.20.1

[PATCH 4/5] riscv: dts: add initial support for the SiFive FU540-C000 SoC

[Paul Walmsley]

Add initial support for the SiFive FU540-C000 SoC.  This is a 28nm SoC
based around the SiFive U54-MC core complex and a TileLink
interconnect.

This file is expected to grow as more device drivers are added to the
kernel.

This patch includes a fix to the QSPI memory map due to a
documentation bug, found by ShihPo Hung <shihpo.hung@sifive.com>, adds
entries for the I2C controller, and merges all DT changes that
formerly were made dynamically by the riscv-pk BBL proxy kernel.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: ShihPo Hung <shihpo.hung@sifive.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 arch/riscv/boot/dts/sifive/fu540-c000.dtsi | 215 +++++++++++++++++++++
 1 file changed, 215 insertions(+)
 create mode 100644 arch/riscv/boot/dts/sifive/fu540-c000.dtsi

diff --git a/arch/riscv/boot/dts/sifive/fu540-c000.dtsi b/arch/riscv/boot/dts/sifive/fu540-c000.dtsi
new file mode 100644
index 000000000000..3c06ee4b2b29
--- /dev/null
+++ b/arch/riscv/boot/dts/sifive/fu540-c000.dtsi
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2018-2019 SiFive, Inc */
+
+/dts-v1/;
+
+#include <dt-bindings/clock/sifive-fu540-prci.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	compatible = "sifive,fu540-c000", "sifive,fu540";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		timebase-frequency = <1000000>;
+		cpu0: cpu@0 {
+			compatible = "sifive,e51", "sifive,rocket0", "riscv";
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <128>;
+			i-cache-size = <16384>;
+			reg = <0>;
+			riscv,isa = "rv64imac";
+			status = "disabled";
+			cpu0_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+		cpu1: cpu@1 {
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <1>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			cpu1_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+		cpu2: cpu@2 {
+			clock-frequency = <0>;
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <2>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			cpu2_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+		cpu3: cpu@3 {
+			clock-frequency = <0>;
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <3>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			cpu3_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+		cpu4: cpu@4 {
+			clock-frequency = <0>;
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <4>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			cpu4_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+	};
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "sifive,fu540-c000", "sifive,fu540", "simple-bus";
+		ranges;
+		plic0: interrupt-controller@c000000 {
+			#interrupt-cells = <1>;
+			compatible = "sifive,plic-1.0.0";
+			reg = <0x0 0xc000000 0x0 0x4000000>;
+			riscv,ndev = <53>;
+			interrupt-controller;
+			interrupts-extended = <
+				&cpu0_intc 0xffffffff
+				&cpu1_intc 0xffffffff &cpu1_intc 9
+				&cpu2_intc 0xffffffff &cpu2_intc 9
+				&cpu3_intc 0xffffffff &cpu3_intc 9
+				&cpu4_intc 0xffffffff &cpu4_intc 9>;
+		};
+		prci: clock-controller@10000000 {
+			compatible = "sifive,fu540-c000-prci";
+			reg = <0x0 0x10000000 0x0 0x1000>;
+			clocks = <&hfclk>, <&rtcclk>;
+			#clock-cells = <1>;
+		};
+		uart0: serial@10010000 {
+			compatible = "sifive,fu540-c000-uart", "sifive,uart0";
+			reg = <0x0 0x10010000 0x0 0x1000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <4>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+		};
+		uart1: serial@10011000 {
+			compatible = "sifive,fu540-c000-uart", "sifive,uart0";
+			reg = <0x0 0x10011000 0x0 0x1000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <5>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+		};
+		i2c0: i2c@10030000 {
+			compatible = "sifive,fu540-c000-i2c", "sifive,i2c0";
+			reg = <0x0 0x10030000 0x0 0x1000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <50>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+			reg-shift = <2>;
+			reg-io-width = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		qspi0: spi@10040000 {
+			compatible = "sifive,fu540-c000-spi", "sifive,spi0";
+			reg = <0x0 0x10040000 0x0 0x1000
+			       0x0 0x20000000 0x0 0x10000000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <51>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		qspi1: spi@10041000 {
+			compatible = "sifive,fu540-c000-spi", "sifive,spi0";
+			reg = <0x0 0x10041000 0x0 0x1000
+			       0x0 0x30000000 0x0 0x10000000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <52>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		qspi2: spi@10050000 {
+			compatible = "sifive,fu540-c000-spi", "sifive,spi0";
+			reg = <0x0 0x10050000 0x0 0x1000>;
+			interrupt-parent = <&plic0>;
+			interrupts = <6>;
+			clocks = <&prci PRCI_CLK_TLCLK>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
-- 
2.20.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH 5/5] riscv: dts: add initial board data for the SiFive HiFive Unleashed

[Paul Walmsley]

Add initial board data for the SiFive HiFive Unleashed A00.

Currently the data populated in this DT file describes the board
DRAM configuration and the external clock sources that supply the
PRCI.

This third version incorporates changes based on more comments from
Rob Herring <robh+dt@kernel.org>.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 arch/riscv/boot/dts/sifive/Makefile           |  2 +
 .../boot/dts/sifive/hifive-unleashed-a00.dts  | 67 +++++++++++++++++++
 2 files changed, 69 insertions(+)
 create mode 100644 arch/riscv/boot/dts/sifive/Makefile
 create mode 100644 arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts

diff --git a/arch/riscv/boot/dts/sifive/Makefile b/arch/riscv/boot/dts/sifive/Makefile
new file mode 100644
index 000000000000..baaeef9efdcb
--- /dev/null
+++ b/arch/riscv/boot/dts/sifive/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-y += hifive-unleashed-a00.dtb
diff --git a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
new file mode 100644
index 000000000000..1de4ea1577d5
--- /dev/null
+++ b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2018-2019 SiFive, Inc */
+
+/dts-v1/;
+
+#include "fu540-c000.dtsi"
+
+/* Clock frequency (in Hz) of the PCB crystal for rtcclk */
+#define RTCCLK_FREQ		1000000
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	model = "SiFive HiFive Unleashed A00";
+	compatible = "sifive,hifive-unleashed-a00", "sifive,fu540-c000";
+
+	chosen {
+	};
+
+	cpus {
+		timebase-frequency = <RTCCLK_FREQ>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x2 0x00000000>;
+	};
+
+	soc {
+	};
+
+	hfclk: hfclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <33333333>;
+		clock-output-names = "hfclk";
+	};
+
+	rtcclk: rtcclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <RTCCLK_FREQ>;
+		clock-output-names = "rtcclk";
+	};
+};
+
+&qspi0 {
+	flash@0 {
+		compatible = "issi,is25wp256", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&qspi2 {
+	status = "okay";
+	mmc@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		voltage-ranges = <3300 3300>;
+		disable-wp;
+	};
+};
-- 
2.20.1

[PATCH 5/5] riscv: dts: add initial board data for the SiFive HiFive Unleashed

[Paul Walmsley]

Add initial board data for the SiFive HiFive Unleashed A00.

Currently the data populated in this DT file describes the board
DRAM configuration and the external clock sources that supply the
PRCI.

This third version incorporates changes based on more comments from
Rob Herring <robh+dt@kernel.org>.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 arch/riscv/boot/dts/sifive/Makefile           |  2 +
 .../boot/dts/sifive/hifive-unleashed-a00.dts  | 67 +++++++++++++++++++
 2 files changed, 69 insertions(+)
 create mode 100644 arch/riscv/boot/dts/sifive/Makefile
 create mode 100644 arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts

diff --git a/arch/riscv/boot/dts/sifive/Makefile b/arch/riscv/boot/dts/sifive/Makefile
new file mode 100644
index 000000000000..baaeef9efdcb
--- /dev/null
+++ b/arch/riscv/boot/dts/sifive/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-y += hifive-unleashed-a00.dtb
diff --git a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
new file mode 100644
index 000000000000..1de4ea1577d5
--- /dev/null
+++ b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2018-2019 SiFive, Inc */
+
+/dts-v1/;
+
+#include "fu540-c000.dtsi"
+
+/* Clock frequency (in Hz) of the PCB crystal for rtcclk */
+#define RTCCLK_FREQ		1000000
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	model = "SiFive HiFive Unleashed A00";
+	compatible = "sifive,hifive-unleashed-a00", "sifive,fu540-c000";
+
+	chosen {
+	};
+
+	cpus {
+		timebase-frequency = <RTCCLK_FREQ>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x2 0x00000000>;
+	};
+
+	soc {
+	};
+
+	hfclk: hfclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <33333333>;
+		clock-output-names = "hfclk";
+	};
+
+	rtcclk: rtcclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <RTCCLK_FREQ>;
+		clock-output-names = "rtcclk";
+	};
+};
+
+&qspi0 {
+	flash@0 {
+		compatible = "issi,is25wp256", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&qspi2 {
+	status = "okay";
+	mmc@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		voltage-ranges = <3300 3300>;
+		disable-wp;
+	};
+};
-- 
2.20.1

[PATCH 5/5] riscv: dts: add initial board data for the SiFive HiFive Unleashed

[Paul Walmsley]

Add initial board data for the SiFive HiFive Unleashed A00.

Currently the data populated in this DT file describes the board
DRAM configuration and the external clock sources that supply the
PRCI.

This third version incorporates changes based on more comments from
Rob Herring <robh+dt@kernel.org>.

Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 arch/riscv/boot/dts/sifive/Makefile           |  2 +
 .../boot/dts/sifive/hifive-unleashed-a00.dts  | 67 +++++++++++++++++++
 2 files changed, 69 insertions(+)
 create mode 100644 arch/riscv/boot/dts/sifive/Makefile
 create mode 100644 arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts

diff --git a/arch/riscv/boot/dts/sifive/Makefile b/arch/riscv/boot/dts/sifive/Makefile
new file mode 100644
index 000000000000..baaeef9efdcb
--- /dev/null
+++ b/arch/riscv/boot/dts/sifive/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-y += hifive-unleashed-a00.dtb
diff --git a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
new file mode 100644
index 000000000000..1de4ea1577d5
--- /dev/null
+++ b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2018-2019 SiFive, Inc */
+
+/dts-v1/;
+
+#include "fu540-c000.dtsi"
+
+/* Clock frequency (in Hz) of the PCB crystal for rtcclk */
+#define RTCCLK_FREQ		1000000
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	model = "SiFive HiFive Unleashed A00";
+	compatible = "sifive,hifive-unleashed-a00", "sifive,fu540-c000";
+
+	chosen {
+	};
+
+	cpus {
+		timebase-frequency = <RTCCLK_FREQ>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x2 0x00000000>;
+	};
+
+	soc {
+	};
+
+	hfclk: hfclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <33333333>;
+		clock-output-names = "hfclk";
+	};
+
+	rtcclk: rtcclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <RTCCLK_FREQ>;
+		clock-output-names = "rtcclk";
+	};
+};
+
+&qspi0 {
+	flash@0 {
+		compatible = "issi,is25wp256", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&qspi2 {
+	status = "okay";
+	mmc@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		voltage-ranges = <3300 3300>;
+		disable-wp;
+	};
+};
-- 
2.20.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH 3/5] dt-bindings: riscv: convert cpu binding to json-schema

[Rob Herring]

On Sun, Jun 2, 2019 at 2:01 AM Paul Walmsley <paul.walmsley@sifive.com> wrote:
>
> At Rob's request, we're starting to migrate our DT binding
> documentation to json-schema YAML format.  Start by converting our cpu
> binding documentation.  While doing so, document more properties and
> nodes.  This includes adding binding documentation support for the E51
> and U54 CPU cores ("harts") that are present on this SoC.  These cores
> are described in:
>
>     https://static.dev.sifive.com/FU540-C000-v1.0.pdf
>
> This cpus.yaml file is intended to be a starting point and to
> evolve over time.  It passes dt-doc-validate as of the yaml-bindings
> commit 4c79d42e9216.
>
> This patch was originally based on the ARM json-schema binding
> documentation as added by commit 672951cbd1b7 ("dt-bindings: arm: Convert
> cpu binding to json-schema").
>
> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
> Signed-off-by: Paul Walmsley <paul@pwsan.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
> Cc: devicetree@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-riscv@lists.infradead.org
> ---
>  .../devicetree/bindings/riscv/cpus.yaml       | 168 ++++++++++++++++++
>  1 file changed, 168 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/riscv/cpus.yaml

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH 3/5] dt-bindings: riscv: convert cpu binding to json-schema

[Rob Herring]

On Sun, Jun 2, 2019 at 2:01 AM Paul Walmsley <paul.walmsley@sifive.com> wrote:
>
> At Rob's request, we're starting to migrate our DT binding
> documentation to json-schema YAML format.  Start by converting our cpu
> binding documentation.  While doing so, document more properties and
> nodes.  This includes adding binding documentation support for the E51
> and U54 CPU cores ("harts") that are present on this SoC.  These cores
> are described in:
>
>     https://static.dev.sifive.com/FU540-C000-v1.0.pdf
>
> This cpus.yaml file is intended to be a starting point and to
> evolve over time.  It passes dt-doc-validate as of the yaml-bindings
> commit 4c79d42e9216.
>
> This patch was originally based on the ARM json-schema binding
> documentation as added by commit 672951cbd1b7 ("dt-bindings: arm: Convert
> cpu binding to json-schema").
>
> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
> Signed-off-by: Paul Walmsley <paul@pwsan.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
> Cc: devicetree@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-riscv@lists.infradead.org
> ---
>  .../devicetree/bindings/riscv/cpus.yaml       | 168 ++++++++++++++++++
>  1 file changed, 168 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/riscv/cpus.yaml

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH 3/5] dt-bindings: riscv: convert cpu binding to json-schema

[Rob Herring]

On Sun, Jun 2, 2019 at 2:01 AM Paul Walmsley <paul.walmsley@sifive.com> wrote:
>
> At Rob's request, we're starting to migrate our DT binding
> documentation to json-schema YAML format.  Start by converting our cpu
> binding documentation.  While doing so, document more properties and
> nodes.  This includes adding binding documentation support for the E51
> and U54 CPU cores ("harts") that are present on this SoC.  These cores
> are described in:
>
>     https://static.dev.sifive.com/FU540-C000-v1.0.pdf
>
> This cpus.yaml file is intended to be a starting point and to
> evolve over time.  It passes dt-doc-validate as of the yaml-bindings
> commit 4c79d42e9216.
>
> This patch was originally based on the ARM json-schema binding
> documentation as added by commit 672951cbd1b7 ("dt-bindings: arm: Convert
> cpu binding to json-schema").
>
> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
> Signed-off-by: Paul Walmsley <paul@pwsan.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
> Cc: devicetree@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-riscv@lists.infradead.org
> ---
>  .../devicetree/bindings/riscv/cpus.yaml       | 168 ++++++++++++++++++
>  1 file changed, 168 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/riscv/cpus.yaml

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH 3/5] dt-bindings: riscv: convert cpu binding to json-schema

[Rob Herring]

On Mon, Jun 10, 2019 at 3:46 PM Rob Herring <robh+dt@kernel.org> wrote:
>
> On Sun, Jun 2, 2019 at 2:01 AM Paul Walmsley <paul.walmsley@sifive.com> wrote:
> >
> > At Rob's request, we're starting to migrate our DT binding
> > documentation to json-schema YAML format.  Start by converting our cpu
> > binding documentation.  While doing so, document more properties and
> > nodes.  This includes adding binding documentation support for the E51
> > and U54 CPU cores ("harts") that are present on this SoC.  These cores
> > are described in:
> >
> >     https://static.dev.sifive.com/FU540-C000-v1.0.pdf
> >
> > This cpus.yaml file is intended to be a starting point and to
> > evolve over time.  It passes dt-doc-validate as of the yaml-bindings
> > commit 4c79d42e9216.
> >
> > This patch was originally based on the ARM json-schema binding
> > documentation as added by commit 672951cbd1b7 ("dt-bindings: arm: Convert
> > cpu binding to json-schema").
> >
> > Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
> > Signed-off-by: Paul Walmsley <paul@pwsan.com>
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: Mark Rutland <mark.rutland@arm.com>
> > Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
> > Cc: devicetree@vger.kernel.org
> > Cc: linux-kernel@vger.kernel.org
> > Cc: linux-riscv@lists.infradead.org
> > ---
> >  .../devicetree/bindings/riscv/cpus.yaml       | 168 ++++++++++++++++++
> >  1 file changed, 168 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/riscv/cpus.yaml
>
> Reviewed-by: Rob Herring <robh@kernel.org>

You all have applied this now leaving the binding checks broken. I
have a fix for one issue validating the schema, but there's a
dependency on schemas/cpus.yaml which I gave feedback on.

Rob

Re: [PATCH 3/5] dt-bindings: riscv: convert cpu binding to json-schema

[Rob Herring]

On Mon, Jun 10, 2019 at 3:46 PM Rob Herring <robh+dt@kernel.org> wrote:
>
> On Sun, Jun 2, 2019 at 2:01 AM Paul Walmsley <paul.walmsley@sifive.com> wrote:
> >
> > At Rob's request, we're starting to migrate our DT binding
> > documentation to json-schema YAML format.  Start by converting our cpu
> > binding documentation.  While doing so, document more properties and
> > nodes.  This includes adding binding documentation support for the E51
> > and U54 CPU cores ("harts") that are present on this SoC.  These cores
> > are described in:
> >
> >     https://static.dev.sifive.com/FU540-C000-v1.0.pdf
> >
> > This cpus.yaml file is intended to be a starting point and to
> > evolve over time.  It passes dt-doc-validate as of the yaml-bindings
> > commit 4c79d42e9216.
> >
> > This patch was originally based on the ARM json-schema binding
> > documentation as added by commit 672951cbd1b7 ("dt-bindings: arm: Convert
> > cpu binding to json-schema").
> >
> > Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
> > Signed-off-by: Paul Walmsley <paul@pwsan.com>
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: Mark Rutland <mark.rutland@arm.com>
> > Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
> > Cc: devicetree@vger.kernel.org
> > Cc: linux-kernel@vger.kernel.org
> > Cc: linux-riscv@lists.infradead.org
> > ---
> >  .../devicetree/bindings/riscv/cpus.yaml       | 168 ++++++++++++++++++
> >  1 file changed, 168 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/riscv/cpus.yaml
>
> Reviewed-by: Rob Herring <robh@kernel.org>

You all have applied this now leaving the binding checks broken. I
have a fix for one issue validating the schema, but there's a
dependency on schemas/cpus.yaml which I gave feedback on.

Rob

Re: [PATCH 3/5] dt-bindings: riscv: convert cpu binding to json-schema

[Rob Herring]

On Mon, Jun 10, 2019 at 3:46 PM Rob Herring <robh+dt@kernel.org> wrote:
>
> On Sun, Jun 2, 2019 at 2:01 AM Paul Walmsley <paul.walmsley@sifive.com> wrote:
> >
> > At Rob's request, we're starting to migrate our DT binding
> > documentation to json-schema YAML format.  Start by converting our cpu
> > binding documentation.  While doing so, document more properties and
> > nodes.  This includes adding binding documentation support for the E51
> > and U54 CPU cores ("harts") that are present on this SoC.  These cores
> > are described in:
> >
> >     https://static.dev.sifive.com/FU540-C000-v1.0.pdf
> >
> > This cpus.yaml file is intended to be a starting point and to
> > evolve over time.  It passes dt-doc-validate as of the yaml-bindings
> > commit 4c79d42e9216.
> >
> > This patch was originally based on the ARM json-schema binding
> > documentation as added by commit 672951cbd1b7 ("dt-bindings: arm: Convert
> > cpu binding to json-schema").
> >
> > Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
> > Signed-off-by: Paul Walmsley <paul@pwsan.com>
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: Mark Rutland <mark.rutland@arm.com>
> > Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
> > Cc: devicetree@vger.kernel.org
> > Cc: linux-kernel@vger.kernel.org
> > Cc: linux-riscv@lists.infradead.org
> > ---
> >  .../devicetree/bindings/riscv/cpus.yaml       | 168 ++++++++++++++++++
> >  1 file changed, 168 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/riscv/cpus.yaml
>
> Reviewed-by: Rob Herring <robh@kernel.org>

You all have applied this now leaving the binding checks broken. I
have a fix for one issue validating the schema, but there's a
dependency on schemas/cpus.yaml which I gave feedback on.

Rob

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH 3/5] dt-bindings: riscv: convert cpu binding to json-schema

[Paul Walmsley]

On Fri, 21 Jun 2019, Rob Herring wrote:

> On Mon, Jun 10, 2019 at 3:46 PM Rob Herring <robh+dt@kernel.org> wrote:
> >
> > On Sun, Jun 2, 2019 at 2:01 AM Paul Walmsley <paul.walmsley@sifive.com> wrote:
> > >
> > > At Rob's request, we're starting to migrate our DT binding
> > > documentation to json-schema YAML format.  Start by converting our cpu
> > > binding documentation.  While doing so, document more properties and
> > > nodes.  This includes adding binding documentation support for the E51
> > > and U54 CPU cores ("harts") that are present on this SoC. 

[ ... ]

> > Reviewed-by: Rob Herring <robh@kernel.org>
> 
> You all have applied this now leaving the binding checks broken. I
> have a fix for one issue validating the schema, but there's a
> dependency on schemas/cpus.yaml which I gave feedback on.

Sorry about that, Rob - will follow up.


- Paul

Re: [PATCH 3/5] dt-bindings: riscv: convert cpu binding to json-schema

[Paul Walmsley]

On Fri, 21 Jun 2019, Rob Herring wrote:

> On Mon, Jun 10, 2019 at 3:46 PM Rob Herring <robh+dt@kernel.org> wrote:
> >
> > On Sun, Jun 2, 2019 at 2:01 AM Paul Walmsley <paul.walmsley@sifive.com> wrote:
> > >
> > > At Rob's request, we're starting to migrate our DT binding
> > > documentation to json-schema YAML format.  Start by converting our cpu
> > > binding documentation.  While doing so, document more properties and
> > > nodes.  This includes adding binding documentation support for the E51
> > > and U54 CPU cores ("harts") that are present on this SoC. 

[ ... ]

> > Reviewed-by: Rob Herring <robh@kernel.org>
> 
> You all have applied this now leaving the binding checks broken. I
> have a fix for one issue validating the schema, but there's a
> dependency on schemas/cpus.yaml which I gave feedback on.

Sorry about that, Rob - will follow up.


- Paul

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv