* [PATCH v3 0/3] Qualcomm UFS device reset support
@ 2019-06-08 5:04 ` Bjorn Andersson
0 siblings, 0 replies; 10+ messages in thread
From: Bjorn Andersson @ 2019-06-08 5:04 UTC (permalink / raw)
Cc: Rob Herring, Mark Rutland, Andy Gross, Alim Akhtar, Avri Altman,
Pedro Sousa, James E.J. Bottomley, Martin K. Petersen,
devicetree, linux-kernel, linux-arm-msm, linux-scsi
This series adds a new ufs vops to allow platform specific methods for
resetting an attached UFS device, then implements this for the Qualcomm driver.
Bjorn Andersson (3):
scsi: ufs: Introduce vops for resetting device
scsi: ufs-qcom: Implement device_reset vops
arm64: dts: qcom: sdm845-mtp: Specify UFS device-reset GPIO
.../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 2 ++
arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 2 ++
drivers/scsi/ufs/ufs-qcom.c | 32 +++++++++++++++++++
drivers/scsi/ufs/ufs-qcom.h | 4 +++
drivers/scsi/ufs/ufshcd.c | 6 ++++
drivers/scsi/ufs/ufshcd.h | 8 +++++
6 files changed, 54 insertions(+)
--
2.18.0
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v3 1/3] scsi: ufs: Introduce vops for resetting device
2019-06-08 5:04 ` Bjorn Andersson
(?)
@ 2019-06-08 5:04 ` Bjorn Andersson
2019-06-25 12:41 ` Alim Akhtar
-1 siblings, 1 reply; 10+ messages in thread
From: Bjorn Andersson @ 2019-06-08 5:04 UTC (permalink / raw)
To: Alim Akhtar, Avri Altman, Pedro Sousa, James E.J. Bottomley,
Martin K. Petersen
Cc: Rob Herring, Mark Rutland, Andy Gross, devicetree, linux-kernel,
linux-arm-msm, linux-scsi
Some UFS memory devices needs their reset line toggled in order to get
them into a good state for initialization. Provide a new vops to allow
the platform driver to implement this operation.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
Changes since v2:
- New patch, to allow moving implementation to platform driver
drivers/scsi/ufs/ufshcd.c | 6 ++++++
drivers/scsi/ufs/ufshcd.h | 8 ++++++++
2 files changed, 14 insertions(+)
diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 04d3686511c8..ee895a625456 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -6191,6 +6191,9 @@ static int ufshcd_reset_and_restore(struct ufs_hba *hba)
int retries = MAX_HOST_RESET_RETRIES;
do {
+ /* Reset the attached device */
+ ufshcd_vops_device_reset(hba);
+
err = ufshcd_host_reset_and_restore(hba);
} while (err && --retries);
@@ -8322,6 +8325,9 @@ int ufshcd_init(struct ufs_hba *hba, void __iomem *mmio_base, unsigned int irq)
goto exit_gating;
}
+ /* Reset the attached device */
+ ufshcd_vops_device_reset(hba);
+
/* Host controller enable */
err = ufshcd_hba_enable(hba);
if (err) {
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index 994d73d03207..cd8139052ed6 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -298,6 +298,7 @@ struct ufs_pwr_mode_info {
* @resume: called during host controller PM callback
* @dbg_register_dump: used to dump controller debug information
* @phy_initialization: used to initialize phys
+ * @device_reset: called to issue a reset pulse on the UFS device
*/
struct ufs_hba_variant_ops {
const char *name;
@@ -326,6 +327,7 @@ struct ufs_hba_variant_ops {
int (*resume)(struct ufs_hba *, enum ufs_pm_op);
void (*dbg_register_dump)(struct ufs_hba *hba);
int (*phy_initialization)(struct ufs_hba *);
+ void (*device_reset)(struct ufs_hba *);
};
/* clock gating state */
@@ -1045,6 +1047,12 @@ static inline void ufshcd_vops_dbg_register_dump(struct ufs_hba *hba)
hba->vops->dbg_register_dump(hba);
}
+static inline void ufshcd_vops_device_reset(struct ufs_hba *hba)
+{
+ if (hba->vops && hba->vops->device_reset)
+ hba->vops->device_reset(hba);
+}
+
extern struct ufs_pm_lvl_states ufs_pm_lvl_states[];
/*
--
2.18.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v3 1/3] scsi: ufs: Introduce vops for resetting device
2019-06-08 5:04 ` [PATCH v3 1/3] scsi: ufs: Introduce vops for resetting device Bjorn Andersson
@ 2019-06-25 12:41 ` Alim Akhtar
2019-06-26 3:45 ` Bjorn Andersson
0 siblings, 1 reply; 10+ messages in thread
From: Alim Akhtar @ 2019-06-25 12:41 UTC (permalink / raw)
To: Bjorn Andersson, Avri Altman, Pedro Sousa, James E.J. Bottomley,
Martin K. Petersen
Cc: Rob Herring, Mark Rutland, Andy Gross, devicetree, linux-kernel,
linux-arm-msm, linux-scsi
Hi Bjorn,
Are you planning to address Bean's comment on patch#2 and want to
re-spin this series?
I am ok with taking this patch as it is and take a Softreset patch as a
separate patch.
On 6/8/19 10:34 AM, Bjorn Andersson wrote:
> Some UFS memory devices needs their reset line toggled in order to get
> them into a good state for initialization. Provide a new vops to allow
> the platform driver to implement this operation.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
feel free to add
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
>
> Changes since v2:
> - New patch, to allow moving implementation to platform driver
>
> drivers/scsi/ufs/ufshcd.c | 6 ++++++
> drivers/scsi/ufs/ufshcd.h | 8 ++++++++
> 2 files changed, 14 insertions(+)
>
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index 04d3686511c8..ee895a625456 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -6191,6 +6191,9 @@ static int ufshcd_reset_and_restore(struct ufs_hba *hba)
> int retries = MAX_HOST_RESET_RETRIES;
>
> do {
> + /* Reset the attached device */
> + ufshcd_vops_device_reset(hba);
> +
> err = ufshcd_host_reset_and_restore(hba);
> } while (err && --retries);
>
> @@ -8322,6 +8325,9 @@ int ufshcd_init(struct ufs_hba *hba, void __iomem *mmio_base, unsigned int irq)
> goto exit_gating;
> }
>
> + /* Reset the attached device */
> + ufshcd_vops_device_reset(hba);
> +
> /* Host controller enable */
> err = ufshcd_hba_enable(hba);
> if (err) {
> diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
> index 994d73d03207..cd8139052ed6 100644
> --- a/drivers/scsi/ufs/ufshcd.h
> +++ b/drivers/scsi/ufs/ufshcd.h
> @@ -298,6 +298,7 @@ struct ufs_pwr_mode_info {
> * @resume: called during host controller PM callback
> * @dbg_register_dump: used to dump controller debug information
> * @phy_initialization: used to initialize phys
> + * @device_reset: called to issue a reset pulse on the UFS device
> */
> struct ufs_hba_variant_ops {
> const char *name;
> @@ -326,6 +327,7 @@ struct ufs_hba_variant_ops {
> int (*resume)(struct ufs_hba *, enum ufs_pm_op);
> void (*dbg_register_dump)(struct ufs_hba *hba);
> int (*phy_initialization)(struct ufs_hba *);
> + void (*device_reset)(struct ufs_hba *);
> };
>
> /* clock gating state */
> @@ -1045,6 +1047,12 @@ static inline void ufshcd_vops_dbg_register_dump(struct ufs_hba *hba)
> hba->vops->dbg_register_dump(hba);
> }
>
> +static inline void ufshcd_vops_device_reset(struct ufs_hba *hba)
> +{
> + if (hba->vops && hba->vops->device_reset)
> + hba->vops->device_reset(hba);
> +}
> +
> extern struct ufs_pm_lvl_states ufs_pm_lvl_states[];
>
> /*
>
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 1/3] scsi: ufs: Introduce vops for resetting device
2019-06-25 12:41 ` Alim Akhtar
@ 2019-06-26 3:45 ` Bjorn Andersson
0 siblings, 0 replies; 10+ messages in thread
From: Bjorn Andersson @ 2019-06-26 3:45 UTC (permalink / raw)
To: Alim Akhtar
Cc: Avri Altman, Pedro Sousa, James E.J. Bottomley,
Martin K. Petersen, Rob Herring, Mark Rutland, Andy Gross,
devicetree, linux-kernel, linux-arm-msm, linux-scsi
On Tue 25 Jun 05:41 PDT 2019, Alim Akhtar wrote:
> Hi Bjorn,
> Are you planning to address Bean's comment on patch#2 and want to
> re-spin this series?
> I am ok with taking this patch as it is and take a Softreset patch as a
> separate patch.
>
I still intend to attempt to implement a softreset "fallback", per
Bean's suggestion - just haven't found the time yet. But I would be
happy to see these patches merged in the meantime, as they do resolve
the issue of failing to being up the UFS link on a significant number of
Qualcomm devices.
I think it's best if you take patch 1 and 2 through your tree and we
take the dts patch through the Qualcomm/arm-soc tree.
Thanks,
Bjorn
> On 6/8/19 10:34 AM, Bjorn Andersson wrote:
> > Some UFS memory devices needs their reset line toggled in order to get
> > them into a good state for initialization. Provide a new vops to allow
> > the platform driver to implement this operation.
> >
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> > ---
> feel free to add
> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
> >
> > Changes since v2:
> > - New patch, to allow moving implementation to platform driver
> >
> > drivers/scsi/ufs/ufshcd.c | 6 ++++++
> > drivers/scsi/ufs/ufshcd.h | 8 ++++++++
> > 2 files changed, 14 insertions(+)
> >
> > diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> > index 04d3686511c8..ee895a625456 100644
> > --- a/drivers/scsi/ufs/ufshcd.c
> > +++ b/drivers/scsi/ufs/ufshcd.c
> > @@ -6191,6 +6191,9 @@ static int ufshcd_reset_and_restore(struct ufs_hba *hba)
> > int retries = MAX_HOST_RESET_RETRIES;
> >
> > do {
> > + /* Reset the attached device */
> > + ufshcd_vops_device_reset(hba);
> > +
> > err = ufshcd_host_reset_and_restore(hba);
> > } while (err && --retries);
> >
> > @@ -8322,6 +8325,9 @@ int ufshcd_init(struct ufs_hba *hba, void __iomem *mmio_base, unsigned int irq)
> > goto exit_gating;
> > }
> >
> > + /* Reset the attached device */
> > + ufshcd_vops_device_reset(hba);
> > +
> > /* Host controller enable */
> > err = ufshcd_hba_enable(hba);
> > if (err) {
> > diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
> > index 994d73d03207..cd8139052ed6 100644
> > --- a/drivers/scsi/ufs/ufshcd.h
> > +++ b/drivers/scsi/ufs/ufshcd.h
> > @@ -298,6 +298,7 @@ struct ufs_pwr_mode_info {
> > * @resume: called during host controller PM callback
> > * @dbg_register_dump: used to dump controller debug information
> > * @phy_initialization: used to initialize phys
> > + * @device_reset: called to issue a reset pulse on the UFS device
> > */
> > struct ufs_hba_variant_ops {
> > const char *name;
> > @@ -326,6 +327,7 @@ struct ufs_hba_variant_ops {
> > int (*resume)(struct ufs_hba *, enum ufs_pm_op);
> > void (*dbg_register_dump)(struct ufs_hba *hba);
> > int (*phy_initialization)(struct ufs_hba *);
> > + void (*device_reset)(struct ufs_hba *);
> > };
> >
> > /* clock gating state */
> > @@ -1045,6 +1047,12 @@ static inline void ufshcd_vops_dbg_register_dump(struct ufs_hba *hba)
> > hba->vops->dbg_register_dump(hba);
> > }
> >
> > +static inline void ufshcd_vops_device_reset(struct ufs_hba *hba)
> > +{
> > + if (hba->vops && hba->vops->device_reset)
> > + hba->vops->device_reset(hba);
> > +}
> > +
> > extern struct ufs_pm_lvl_states ufs_pm_lvl_states[];
> >
> > /*
> >
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v3 2/3] scsi: ufs-qcom: Implement device_reset vops
2019-06-08 5:04 ` Bjorn Andersson
(?)
(?)
@ 2019-06-08 5:04 ` Bjorn Andersson
2019-06-11 16:08 ` [EXT] " Bean Huo (beanhuo)
-1 siblings, 1 reply; 10+ messages in thread
From: Bjorn Andersson @ 2019-06-08 5:04 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Alim Akhtar, Avri Altman, Pedro Sousa,
James E.J. Bottomley, Martin K. Petersen
Cc: Andy Gross, devicetree, linux-kernel, linux-arm-msm, linux-scsi
The UFS_RESET pin on Qualcomm SoCs are controlled by TLMM and exposed
through the GPIO framework. Acquire the device-reset GPIO and use this
to implement the device_reset vops, to allow resetting the attached
memory.
Based on downstream support implemented by Subhash Jadavani
<subhashj@codeaurora.org>.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
Changes since v2:
- Moved implementation to Qualcomm driver
.../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 2 ++
drivers/scsi/ufs/ufs-qcom.c | 32 +++++++++++++++++++
drivers/scsi/ufs/ufs-qcom.h | 4 +++
3 files changed, 38 insertions(+)
diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
index a74720486ee2..d562d8b4919c 100644
--- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
+++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
@@ -54,6 +54,8 @@ Optional properties:
PHY reset from the UFS controller.
- resets : reset node register
- reset-names : describe reset node register, the "rst" corresponds to reset the whole UFS IP.
+- device-reset-gpios : A phandle and gpio specifier denoting the GPIO connected
+ to the RESET pin of the UFS memory device.
Note: If above properties are not defined it can be assumed that the supply
regulators or clocks are always on.
diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c
index ea7219407309..efaf57ba618a 100644
--- a/drivers/scsi/ufs/ufs-qcom.c
+++ b/drivers/scsi/ufs/ufs-qcom.c
@@ -16,6 +16,7 @@
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/phy/phy.h>
+#include <linux/gpio/consumer.h>
#include <linux/reset-controller.h>
#include "ufshcd.h"
@@ -1141,6 +1142,15 @@ static int ufs_qcom_init(struct ufs_hba *hba)
goto out_variant_clear;
}
+ host->device_reset = devm_gpiod_get_optional(dev, "device-reset",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(host->device_reset)) {
+ err = PTR_ERR(host->device_reset);
+ if (err != -EPROBE_DEFER)
+ dev_err(dev, "failed to acquire reset gpio: %d\n", err);
+ goto out_variant_clear;
+ }
+
err = ufs_qcom_bus_register(host);
if (err)
goto out_variant_clear;
@@ -1546,6 +1556,27 @@ static void ufs_qcom_dump_dbg_regs(struct ufs_hba *hba)
usleep_range(1000, 1100);
}
+/**
+ * ufs_qcom_device_reset() - toggle the (optional) device reset line
+ * @hba: per-adapter instance
+ *
+ * Toggles the (optional) reset line to reset the attached device.
+ */
+static void ufs_qcom_device_reset(struct ufs_hba *hba)
+{
+ struct ufs_qcom_host *host = ufshcd_get_variant(hba);
+
+ /*
+ * The UFS device shall detect reset pulses of 1us, sleep for 10us to
+ * be on the safe side.
+ */
+ gpiod_set_value_cansleep(host->device_reset, 1);
+ usleep_range(10, 15);
+
+ gpiod_set_value_cansleep(host->device_reset, 0);
+ usleep_range(10, 15);
+}
+
/**
* struct ufs_hba_qcom_vops - UFS QCOM specific variant operations
*
@@ -1566,6 +1597,7 @@ static struct ufs_hba_variant_ops ufs_hba_qcom_vops = {
.suspend = ufs_qcom_suspend,
.resume = ufs_qcom_resume,
.dbg_register_dump = ufs_qcom_dump_dbg_regs,
+ .device_reset = ufs_qcom_device_reset,
};
/**
diff --git a/drivers/scsi/ufs/ufs-qcom.h b/drivers/scsi/ufs/ufs-qcom.h
index 68a880185752..b96ffb6804e4 100644
--- a/drivers/scsi/ufs/ufs-qcom.h
+++ b/drivers/scsi/ufs/ufs-qcom.h
@@ -204,6 +204,8 @@ struct ufs_qcom_testbus {
u8 select_minor;
};
+struct gpio_desc;
+
struct ufs_qcom_host {
/*
* Set this capability if host controller supports the QUniPro mode
@@ -241,6 +243,8 @@ struct ufs_qcom_host {
struct ufs_qcom_testbus testbus;
struct reset_controller_dev rcdev;
+
+ struct gpio_desc *device_reset;
};
static inline u32
--
2.18.0
^ permalink raw reply related [flat|nested] 10+ messages in thread
* RE: [EXT] [PATCH v3 2/3] scsi: ufs-qcom: Implement device_reset vops
2019-06-08 5:04 ` [PATCH v3 2/3] scsi: ufs-qcom: Implement device_reset vops Bjorn Andersson
@ 2019-06-11 16:08 ` Bean Huo (beanhuo)
2019-06-12 6:31 ` Bjorn Andersson
0 siblings, 1 reply; 10+ messages in thread
From: Bean Huo (beanhuo) @ 2019-06-11 16:08 UTC (permalink / raw)
To: Bjorn Andersson, Rob Herring, Mark Rutland, Alim Akhtar,
Avri Altman, Pedro Sousa, James E.J. Bottomley,
Martin K. Petersen
Cc: Andy Gross, devicetree, linux-kernel, linux-arm-msm, linux-scsi
Hi, Bjorn
This HW reset is dedicated to QUALCOMM based platform case.
how about adding a SW reset as to be default reset routine if platform doesn't support HW reset?
>-----Original Message-----
>From: linux-scsi-owner@vger.kernel.org <linux-scsi-owner@vger.kernel.org>
>On Behalf Of Bjorn Andersson
>Sent: Saturday, June 8, 2019 7:05 AM
>To: Rob Herring <robh+dt@kernel.org>; Mark Rutland
><mark.rutland@arm.com>; Alim Akhtar <alim.akhtar@samsung.com>; Avri
>Altman <avri.altman@wdc.com>; Pedro Sousa
><pedrom.sousa@synopsys.com>; James E.J. Bottomley <jejb@linux.ibm.com>;
>Martin K. Petersen <martin.petersen@oracle.com>
>Cc: Andy Gross <agross@kernel.org>; devicetree@vger.kernel.org; linux-
>kernel@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux-
>scsi@vger.kernel.org
>Subject: [EXT] [PATCH v3 2/3] scsi: ufs-qcom: Implement device_reset vops
>
>The UFS_RESET pin on Qualcomm SoCs are controlled by TLMM and exposed
>through the GPIO framework. Acquire the device-reset GPIO and use this to
>implement the device_reset vops, to allow resetting the attached memory.
>
>Based on downstream support implemented by Subhash Jadavani
><subhashj@codeaurora.org>.
>
>Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
>---
>
>Changes since v2:
>- Moved implementation to Qualcomm driver
>
> .../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 2 ++
> drivers/scsi/ufs/ufs-qcom.c | 32 +++++++++++++++++++
> drivers/scsi/ufs/ufs-qcom.h | 4 +++
> 3 files changed, 38 insertions(+)
>
>diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>index a74720486ee2..d562d8b4919c 100644
>--- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>+++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>@@ -54,6 +54,8 @@ Optional properties:
> PHY reset from the UFS controller.
> - resets : reset node register
> - reset-names : describe reset node register, the "rst" corresponds to
>reset the whole UFS IP.
>+- device-reset-gpios : A phandle and gpio specifier denoting the GPIO
>connected
>+ to the RESET pin of the UFS memory device.
>
> Note: If above properties are not defined it can be assumed that the supply
>regulators or clocks are always on.
>diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c index
>ea7219407309..efaf57ba618a 100644
>--- a/drivers/scsi/ufs/ufs-qcom.c
>+++ b/drivers/scsi/ufs/ufs-qcom.c
>@@ -16,6 +16,7 @@
> #include <linux/of.h>
> #include <linux/platform_device.h>
> #include <linux/phy/phy.h>
>+#include <linux/gpio/consumer.h>
> #include <linux/reset-controller.h>
>
> #include "ufshcd.h"
>@@ -1141,6 +1142,15 @@ static int ufs_qcom_init(struct ufs_hba *hba)
> goto out_variant_clear;
> }
>
>+ host->device_reset = devm_gpiod_get_optional(dev, "device-reset",
>+ GPIOD_OUT_HIGH);
>+ if (IS_ERR(host->device_reset)) {
>+ err = PTR_ERR(host->device_reset);
>+ if (err != -EPROBE_DEFER)
>+ dev_err(dev, "failed to acquire reset gpio: %d\n", err);
>+ goto out_variant_clear;
>+ }
>+
> err = ufs_qcom_bus_register(host);
> if (err)
> goto out_variant_clear;
>@@ -1546,6 +1556,27 @@ static void ufs_qcom_dump_dbg_regs(struct
>ufs_hba *hba)
> usleep_range(1000, 1100);
> }
>
>+/**
>+ * ufs_qcom_device_reset() - toggle the (optional) device reset line
>+ * @hba: per-adapter instance
>+ *
>+ * Toggles the (optional) reset line to reset the attached device.
>+ */
>+static void ufs_qcom_device_reset(struct ufs_hba *hba) {
>+ struct ufs_qcom_host *host = ufshcd_get_variant(hba);
>+
>+ /*
>+ * The UFS device shall detect reset pulses of 1us, sleep for 10us to
>+ * be on the safe side.
>+ */
>+ gpiod_set_value_cansleep(host->device_reset, 1);
>+ usleep_range(10, 15);
>+
>+ gpiod_set_value_cansleep(host->device_reset, 0);
>+ usleep_range(10, 15);
>+}
>+
> /**
> * struct ufs_hba_qcom_vops - UFS QCOM specific variant operations
> *
>@@ -1566,6 +1597,7 @@ static struct ufs_hba_variant_ops
>ufs_hba_qcom_vops = {
> .suspend = ufs_qcom_suspend,
> .resume = ufs_qcom_resume,
> .dbg_register_dump = ufs_qcom_dump_dbg_regs,
>+ .device_reset = ufs_qcom_device_reset,
> };
>
> /**
>diff --git a/drivers/scsi/ufs/ufs-qcom.h b/drivers/scsi/ufs/ufs-qcom.h index
>68a880185752..b96ffb6804e4 100644
>--- a/drivers/scsi/ufs/ufs-qcom.h
>+++ b/drivers/scsi/ufs/ufs-qcom.h
>@@ -204,6 +204,8 @@ struct ufs_qcom_testbus {
> u8 select_minor;
> };
>
>+struct gpio_desc;
>+
> struct ufs_qcom_host {
> /*
> * Set this capability if host controller supports the QUniPro mode
>@@ -241,6 +243,8 @@ struct ufs_qcom_host {
> struct ufs_qcom_testbus testbus;
>
> struct reset_controller_dev rcdev;
>+
>+ struct gpio_desc *device_reset;
> };
>
> static inline u32
>--
>2.18.0
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [EXT] [PATCH v3 2/3] scsi: ufs-qcom: Implement device_reset vops
2019-06-11 16:08 ` [EXT] " Bean Huo (beanhuo)
@ 2019-06-12 6:31 ` Bjorn Andersson
2019-06-14 7:42 ` Bean Huo (beanhuo)
0 siblings, 1 reply; 10+ messages in thread
From: Bjorn Andersson @ 2019-06-12 6:31 UTC (permalink / raw)
To: Bean Huo (beanhuo)
Cc: Rob Herring, Mark Rutland, Alim Akhtar, Avri Altman, Pedro Sousa,
James E.J. Bottomley, Martin K. Petersen, Andy Gross, devicetree,
linux-kernel, linux-arm-msm, linux-scsi
On Tue 11 Jun 09:08 PDT 2019, Bean Huo (beanhuo) wrote:
> Hi, Bjorn
> This HW reset is dedicated to QUALCOMM based platform case.
> how about adding a SW reset as to be default reset routine if platform doesn't support HW reset?
>
Can you please advice how I perform such software reset?
Regards,
Bjorn
> >-----Original Message-----
> >From: linux-scsi-owner@vger.kernel.org <linux-scsi-owner@vger.kernel.org>
> >On Behalf Of Bjorn Andersson
> >Sent: Saturday, June 8, 2019 7:05 AM
> >To: Rob Herring <robh+dt@kernel.org>; Mark Rutland
> ><mark.rutland@arm.com>; Alim Akhtar <alim.akhtar@samsung.com>; Avri
> >Altman <avri.altman@wdc.com>; Pedro Sousa
> ><pedrom.sousa@synopsys.com>; James E.J. Bottomley <jejb@linux.ibm.com>;
> >Martin K. Petersen <martin.petersen@oracle.com>
> >Cc: Andy Gross <agross@kernel.org>; devicetree@vger.kernel.org; linux-
> >kernel@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux-
> >scsi@vger.kernel.org
> >Subject: [EXT] [PATCH v3 2/3] scsi: ufs-qcom: Implement device_reset vops
> >
> >The UFS_RESET pin on Qualcomm SoCs are controlled by TLMM and exposed
> >through the GPIO framework. Acquire the device-reset GPIO and use this to
> >implement the device_reset vops, to allow resetting the attached memory.
> >
> >Based on downstream support implemented by Subhash Jadavani
> ><subhashj@codeaurora.org>.
> >
> >Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> >---
> >
> >Changes since v2:
> >- Moved implementation to Qualcomm driver
> >
> > .../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 2 ++
> > drivers/scsi/ufs/ufs-qcom.c | 32 +++++++++++++++++++
> > drivers/scsi/ufs/ufs-qcom.h | 4 +++
> > 3 files changed, 38 insertions(+)
> >
> >diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> >b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> >index a74720486ee2..d562d8b4919c 100644
> >--- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> >+++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> >@@ -54,6 +54,8 @@ Optional properties:
> > PHY reset from the UFS controller.
> > - resets : reset node register
> > - reset-names : describe reset node register, the "rst" corresponds to
> >reset the whole UFS IP.
> >+- device-reset-gpios : A phandle and gpio specifier denoting the GPIO
> >connected
> >+ to the RESET pin of the UFS memory device.
> >
> > Note: If above properties are not defined it can be assumed that the supply
> >regulators or clocks are always on.
> >diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c index
> >ea7219407309..efaf57ba618a 100644
> >--- a/drivers/scsi/ufs/ufs-qcom.c
> >+++ b/drivers/scsi/ufs/ufs-qcom.c
> >@@ -16,6 +16,7 @@
> > #include <linux/of.h>
> > #include <linux/platform_device.h>
> > #include <linux/phy/phy.h>
> >+#include <linux/gpio/consumer.h>
> > #include <linux/reset-controller.h>
> >
> > #include "ufshcd.h"
> >@@ -1141,6 +1142,15 @@ static int ufs_qcom_init(struct ufs_hba *hba)
> > goto out_variant_clear;
> > }
> >
> >+ host->device_reset = devm_gpiod_get_optional(dev, "device-reset",
> >+ GPIOD_OUT_HIGH);
> >+ if (IS_ERR(host->device_reset)) {
> >+ err = PTR_ERR(host->device_reset);
> >+ if (err != -EPROBE_DEFER)
> >+ dev_err(dev, "failed to acquire reset gpio: %d\n", err);
> >+ goto out_variant_clear;
> >+ }
> >+
> > err = ufs_qcom_bus_register(host);
> > if (err)
> > goto out_variant_clear;
> >@@ -1546,6 +1556,27 @@ static void ufs_qcom_dump_dbg_regs(struct
> >ufs_hba *hba)
> > usleep_range(1000, 1100);
> > }
> >
> >+/**
> >+ * ufs_qcom_device_reset() - toggle the (optional) device reset line
> >+ * @hba: per-adapter instance
> >+ *
> >+ * Toggles the (optional) reset line to reset the attached device.
> >+ */
> >+static void ufs_qcom_device_reset(struct ufs_hba *hba) {
> >+ struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> >+
> >+ /*
> >+ * The UFS device shall detect reset pulses of 1us, sleep for 10us to
> >+ * be on the safe side.
> >+ */
> >+ gpiod_set_value_cansleep(host->device_reset, 1);
> >+ usleep_range(10, 15);
> >+
> >+ gpiod_set_value_cansleep(host->device_reset, 0);
> >+ usleep_range(10, 15);
> >+}
> >+
> > /**
> > * struct ufs_hba_qcom_vops - UFS QCOM specific variant operations
> > *
> >@@ -1566,6 +1597,7 @@ static struct ufs_hba_variant_ops
> >ufs_hba_qcom_vops = {
> > .suspend = ufs_qcom_suspend,
> > .resume = ufs_qcom_resume,
> > .dbg_register_dump = ufs_qcom_dump_dbg_regs,
> >+ .device_reset = ufs_qcom_device_reset,
> > };
> >
> > /**
> >diff --git a/drivers/scsi/ufs/ufs-qcom.h b/drivers/scsi/ufs/ufs-qcom.h index
> >68a880185752..b96ffb6804e4 100644
> >--- a/drivers/scsi/ufs/ufs-qcom.h
> >+++ b/drivers/scsi/ufs/ufs-qcom.h
> >@@ -204,6 +204,8 @@ struct ufs_qcom_testbus {
> > u8 select_minor;
> > };
> >
> >+struct gpio_desc;
> >+
> > struct ufs_qcom_host {
> > /*
> > * Set this capability if host controller supports the QUniPro mode
> >@@ -241,6 +243,8 @@ struct ufs_qcom_host {
> > struct ufs_qcom_testbus testbus;
> >
> > struct reset_controller_dev rcdev;
> >+
> >+ struct gpio_desc *device_reset;
> > };
> >
> > static inline u32
> >--
> >2.18.0
>
^ permalink raw reply [flat|nested] 10+ messages in thread
* RE: [EXT] [PATCH v3 2/3] scsi: ufs-qcom: Implement device_reset vops
2019-06-12 6:31 ` Bjorn Andersson
@ 2019-06-14 7:42 ` Bean Huo (beanhuo)
0 siblings, 0 replies; 10+ messages in thread
From: Bean Huo (beanhuo) @ 2019-06-14 7:42 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Rob Herring, Mark Rutland, Alim Akhtar, Avri Altman, Pedro Sousa,
James E.J. Bottomley, Martin K. Petersen, Andy Gross, devicetree,
linux-kernel, linux-arm-msm, linux-scsi
Hi, Bjorn
Sorry just saw your message.
You can use UIC command,through function ufshcd_send_uic_cmd( ) with UIC_CMD_DME_END_PT_RST command.
DME_ENDPOINTRESET: It is used when UFS host wants the UFS device to perform a reset.
//bean
>On Tue 11 Jun 09:08 PDT 2019, Bean Huo (beanhuo) wrote:
>
>> Hi, Bjorn
>> This HW reset is dedicated to QUALCOMM based platform case.
>> how about adding a SW reset as to be default reset routine if platform
>doesn't support HW reset?
>>
>
>Can you please advice how I perform such software reset?
>
>Regards,
>Bjorn
>
>> >-----Original Message-----
>> >From: linux-scsi-owner@vger.kernel.org
>> ><linux-scsi-owner@vger.kernel.org>
>> >On Behalf Of Bjorn Andersson
>> >Sent: Saturday, June 8, 2019 7:05 AM
>> >To: Rob Herring <robh+dt@kernel.org>; Mark Rutland
>> ><mark.rutland@arm.com>; Alim Akhtar <alim.akhtar@samsung.com>; Avri
>> >Altman <avri.altman@wdc.com>; Pedro Sousa
>> ><pedrom.sousa@synopsys.com>; James E.J. Bottomley
>> ><jejb@linux.ibm.com>; Martin K. Petersen <martin.petersen@oracle.com>
>> >Cc: Andy Gross <agross@kernel.org>; devicetree@vger.kernel.org;
>> >linux- kernel@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux-
>> >scsi@vger.kernel.org
>> >Subject: [EXT] [PATCH v3 2/3] scsi: ufs-qcom: Implement device_reset
>> >vops
>> >
>> >The UFS_RESET pin on Qualcomm SoCs are controlled by TLMM and
>exposed
>> >through the GPIO framework. Acquire the device-reset GPIO and use
>> >this to implement the device_reset vops, to allow resetting the attached
>memory.
>> >
>> >Based on downstream support implemented by Subhash Jadavani
>> ><subhashj@codeaurora.org>.
>> >
>> >Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
>> >---
>> >
>> >Changes since v2:
>> >- Moved implementation to Qualcomm driver
>> >
>> > .../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 2 ++
>> > drivers/scsi/ufs/ufs-qcom.c | 32 +++++++++++++++++++
>> > drivers/scsi/ufs/ufs-qcom.h | 4 +++
>> > 3 files changed, 38 insertions(+)
>> >
>> >diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> >b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> >index a74720486ee2..d562d8b4919c 100644
>> >--- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> >+++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
>> >@@ -54,6 +54,8 @@ Optional properties:
>> > PHY reset from the UFS controller.
>> > - resets : reset node register
>> > - reset-names : describe reset node register, the "rst" corresponds to
>> >reset the whole UFS IP.
>> >+- device-reset-gpios : A phandle and gpio specifier denoting the
>GPIO
>> >connected
>> >+ to the RESET pin of the UFS memory device.
>> >
>> > Note: If above properties are not defined it can be assumed that the
>> >supply regulators or clocks are always on.
>> >diff --git a/drivers/scsi/ufs/ufs-qcom.c
>> >b/drivers/scsi/ufs/ufs-qcom.c index ea7219407309..efaf57ba618a 100644
>> >--- a/drivers/scsi/ufs/ufs-qcom.c
>> >+++ b/drivers/scsi/ufs/ufs-qcom.c
>> >@@ -16,6 +16,7 @@
>> > #include <linux/of.h>
>> > #include <linux/platform_device.h>
>> > #include <linux/phy/phy.h>
>> >+#include <linux/gpio/consumer.h>
>> > #include <linux/reset-controller.h>
>> >
>> > #include "ufshcd.h"
>> >@@ -1141,6 +1142,15 @@ static int ufs_qcom_init(struct ufs_hba *hba)
>> > goto out_variant_clear;
>> > }
>> >
>> >+ host->device_reset = devm_gpiod_get_optional(dev, "device-reset",
>> >+ GPIOD_OUT_HIGH);
>> >+ if (IS_ERR(host->device_reset)) {
>> >+ err = PTR_ERR(host->device_reset);
>> >+ if (err != -EPROBE_DEFER)
>> >+ dev_err(dev, "failed to acquire reset gpio: %d\n", err);
>> >+ goto out_variant_clear;
>> >+ }
>> >+
>> > err = ufs_qcom_bus_register(host);
>> > if (err)
>> > goto out_variant_clear;
>> >@@ -1546,6 +1556,27 @@ static void ufs_qcom_dump_dbg_regs(struct
>> >ufs_hba *hba)
>> > usleep_range(1000, 1100);
>> > }
>> >
>> >+/**
>> >+ * ufs_qcom_device_reset() - toggle the (optional) device reset line
>> >+ * @hba: per-adapter instance
>> >+ *
>> >+ * Toggles the (optional) reset line to reset the attached device.
>> >+ */
>> >+static void ufs_qcom_device_reset(struct ufs_hba *hba) {
>> >+ struct ufs_qcom_host *host = ufshcd_get_variant(hba);
>> >+
>> >+ /*
>> >+ * The UFS device shall detect reset pulses of 1us, sleep for 10us to
>> >+ * be on the safe side.
>> >+ */
>> >+ gpiod_set_value_cansleep(host->device_reset, 1);
>> >+ usleep_range(10, 15);
>> >+
>> >+ gpiod_set_value_cansleep(host->device_reset, 0);
>> >+ usleep_range(10, 15);
>> >+}
>> >+
>> > /**
>> > * struct ufs_hba_qcom_vops - UFS QCOM specific variant operations
>> > *
>> >@@ -1566,6 +1597,7 @@ static struct ufs_hba_variant_ops
>> >ufs_hba_qcom_vops = {
>> > .suspend = ufs_qcom_suspend,
>> > .resume = ufs_qcom_resume,
>> > .dbg_register_dump = ufs_qcom_dump_dbg_regs,
>> >+ .device_reset = ufs_qcom_device_reset,
>> > };
>> >
>> > /**
>> >diff --git a/drivers/scsi/ufs/ufs-qcom.h
>> >b/drivers/scsi/ufs/ufs-qcom.h index
>> >68a880185752..b96ffb6804e4 100644
>> >--- a/drivers/scsi/ufs/ufs-qcom.h
>> >+++ b/drivers/scsi/ufs/ufs-qcom.h
>> >@@ -204,6 +204,8 @@ struct ufs_qcom_testbus {
>> > u8 select_minor;
>> > };
>> >
>> >+struct gpio_desc;
>> >+
>> > struct ufs_qcom_host {
>> > /*
>> > * Set this capability if host controller supports the QUniPro mode
>> >@@ -241,6 +243,8 @@ struct ufs_qcom_host {
>> > struct ufs_qcom_testbus testbus;
>> >
>> > struct reset_controller_dev rcdev;
>> >+
>> >+ struct gpio_desc *device_reset;
>> > };
>> >
>> > static inline u32
>> >--
>> >2.18.0
>>
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v3 3/3] arm64: dts: qcom: sdm845-mtp: Specify UFS device-reset GPIO
2019-06-08 5:04 ` Bjorn Andersson
` (2 preceding siblings ...)
(?)
@ 2019-06-08 5:04 ` Bjorn Andersson
-1 siblings, 0 replies; 10+ messages in thread
From: Bjorn Andersson @ 2019-06-08 5:04 UTC (permalink / raw)
To: Andy Gross
Cc: Rob Herring, Mark Rutland, Alim Akhtar, Avri Altman, Pedro Sousa,
James E.J. Bottomley, Martin K. Petersen, devicetree,
linux-kernel, linux-arm-msm, linux-scsi
Specify the UFS device-reset gpio, so that the controller will issue a
reset of the UFS device.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
Changes since v2:
- None
arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
index 80189807b4e5..441045847e9f 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
@@ -467,6 +467,8 @@
&ufs_mem_hc {
status = "okay";
+ device-reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
vcc-supply = <&vreg_l20a_2p95>;
vcc-max-microamp = <600000>;
};
--
2.18.0
^ permalink raw reply related [flat|nested] 10+ messages in thread