All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v6 0/5] MTD: Add Initial Hyperbus support
@ 2019-06-18  9:28 ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

Change log:
Since v5:
Fix up DT bindings comments for TI HBMC driver
Move calibration sequence out of core into TI HBMC driver

Since v4:
Fix Rob's comments on dt-bindings of TI HBMC driver

Since v3:
* Drop reading QRY string twice in hyperbus_calibrate()
* Fix doc/misc comments on v3.

Since RFC v2:
* use map_word_xxx() for handling status register to support interleaved
  flashes as suggested by Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
* Report error status/messages on erase/program failure by looking at
  status register bits.
* Add "cfi-flash" as fallback compatible for cypress,hyperflash
* Add support to select between HyperBus and OSPI using mmio mux

Since RFC v1:
* Re-work Hyperbus core to provide separate struct representation for
  controller and slave devices
* Rename all files and func names to have hyperbus_ prefix
* Provide default calibration routine for use by controller drivers
* Fix up errors with patch spliting
* Address comments by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>


Cypress HyperBus is Low Signal Count, High Performance Double Data Rate Bus
interface between a host system master and one or more slave interfaces.
HyperBus is used to connect microprocessor, microcontroller, or ASIC
devices with random access NOR flash memory(called HyperFlash) or
self refresh DRAM(called HyperRAM).

Its a 8-bit data bus (DQ[7:0]) with  Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].

HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since Hyperbus is x8 DDR bus,
its equivalent to x16 parallel NOR flash wrt bits per clk. But Hyperbus
operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.
Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller(HBMC) drivers call hyperbus_register_device() to register a
single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.

This is an early RFC, to know if its okay to use maps framework and existing
CFI compliant flash support code to support Hyperflash
Also would like input on different types of HBMC master IPs out there
and their programming sequences.
Would appreciate any testing/review.

Tested on modified TI AM654 EVM with Cypress Hyperflash S26KS512 by
creating a UBIFS partition and writing and reading files to it.
Stress tested by writing/reading 16MB flash repeatedly at different
offsets using dd commmand.

HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]
TI's HBMC controller details at[3]

[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
    Table 12-5741. HyperFlash Access Sequence


Vignesh Raghavendra (5):
  mtd: cfi_cmdset_0002: Add support for polling status register
  dt-bindings: mtd: Add binding documentation for HyperFlash
  mtd: Add support for HyperBus memory devices
  dt-bindings: mtd: Add bindings for TI's AM654 HyperBus memory
    controller
  mtd: hyperbus: Add driver for TI's HyperBus memory controller

 .../bindings/mtd/cypress,hyperflash.txt       |  13 ++
 .../devicetree/bindings/mtd/ti,am654-hbmc.txt |  51 ++++++
 MAINTAINERS                                   |   8 +
 drivers/mtd/Kconfig                           |   2 +
 drivers/mtd/Makefile                          |   1 +
 drivers/mtd/chips/cfi_cmdset_0002.c           |  90 ++++++++++
 drivers/mtd/hyperbus/Kconfig                  |  23 +++
 drivers/mtd/hyperbus/Makefile                 |   4 +
 drivers/mtd/hyperbus/hbmc-am654.c             | 141 ++++++++++++++++
 drivers/mtd/hyperbus/hyperbus-core.c          | 154 ++++++++++++++++++
 include/linux/mtd/cfi.h                       |   5 +
 include/linux/mtd/hyperbus.h                  |  86 ++++++++++
 12 files changed, 578 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
 create mode 100644 Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
 create mode 100644 drivers/mtd/hyperbus/Kconfig
 create mode 100644 drivers/mtd/hyperbus/Makefile
 create mode 100644 drivers/mtd/hyperbus/hbmc-am654.c
 create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c
 create mode 100644 include/linux/mtd/hyperbus.h

-- 
2.21.0


^ permalink raw reply	[flat|nested] 24+ messages in thread
* [PATCH v6 0/5] MTD: Add Initial Hyperbus support
@ 2019-06-18  9:28 ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Change log:
Since v5:
Fix up DT bindings comments for TI HBMC driver
Move calibration sequence out of core into TI HBMC driver

Since v4:
Fix Rob's comments on dt-bindings of TI HBMC driver

Since v3:
* Drop reading QRY string twice in hyperbus_calibrate()
* Fix doc/misc comments on v3.

Since RFC v2:
* use map_word_xxx() for handling status register to support interleaved
  flashes as suggested by Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
* Report error status/messages on erase/program failure by looking at
  status register bits.
* Add "cfi-flash" as fallback compatible for cypress,hyperflash
* Add support to select between HyperBus and OSPI using mmio mux

Since RFC v1:
* Re-work Hyperbus core to provide separate struct representation for
  controller and slave devices
* Rename all files and func names to have hyperbus_ prefix
* Provide default calibration routine for use by controller drivers
* Fix up errors with patch spliting
* Address comments by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>


Cypress HyperBus is Low Signal Count, High Performance Double Data Rate Bus
interface between a host system master and one or more slave interfaces.
HyperBus is used to connect microprocessor, microcontroller, or ASIC
devices with random access NOR flash memory(called HyperFlash) or
self refresh DRAM(called HyperRAM).

Its a 8-bit data bus (DQ[7:0]) with  Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].

HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since Hyperbus is x8 DDR bus,
its equivalent to x16 parallel NOR flash wrt bits per clk. But Hyperbus
operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.
Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller(HBMC) drivers call hyperbus_register_device() to register a
single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.

This is an early RFC, to know if its okay to use maps framework and existing
CFI compliant flash support code to support Hyperflash
Also would like input on different types of HBMC master IPs out there
and their programming sequences.
Would appreciate any testing/review.

Tested on modified TI AM654 EVM with Cypress Hyperflash S26KS512 by
creating a UBIFS partition and writing and reading files to it.
Stress tested by writing/reading 16MB flash repeatedly at different
offsets using dd commmand.

HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]
TI's HBMC controller details at[3]

[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
    Table 12-5741. HyperFlash Access Sequence


Vignesh Raghavendra (5):
  mtd: cfi_cmdset_0002: Add support for polling status register
  dt-bindings: mtd: Add binding documentation for HyperFlash
  mtd: Add support for HyperBus memory devices
  dt-bindings: mtd: Add bindings for TI's AM654 HyperBus memory
    controller
  mtd: hyperbus: Add driver for TI's HyperBus memory controller

 .../bindings/mtd/cypress,hyperflash.txt       |  13 ++
 .../devicetree/bindings/mtd/ti,am654-hbmc.txt |  51 ++++++
 MAINTAINERS                                   |   8 +
 drivers/mtd/Kconfig                           |   2 +
 drivers/mtd/Makefile                          |   1 +
 drivers/mtd/chips/cfi_cmdset_0002.c           |  90 ++++++++++
 drivers/mtd/hyperbus/Kconfig                  |  23 +++
 drivers/mtd/hyperbus/Makefile                 |   4 +
 drivers/mtd/hyperbus/hbmc-am654.c             | 141 ++++++++++++++++
 drivers/mtd/hyperbus/hyperbus-core.c          | 154 ++++++++++++++++++
 include/linux/mtd/cfi.h                       |   5 +
 include/linux/mtd/hyperbus.h                  |  86 ++++++++++
 12 files changed, 578 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
 create mode 100644 Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
 create mode 100644 drivers/mtd/hyperbus/Kconfig
 create mode 100644 drivers/mtd/hyperbus/Makefile
 create mode 100644 drivers/mtd/hyperbus/hbmc-am654.c
 create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c
 create mode 100644 include/linux/mtd/hyperbus.h

-- 
2.21.0

^ permalink raw reply	[flat|nested] 24+ messages in thread
* [PATCH v6 0/5] MTD: Add Initial Hyperbus support
@ 2019-06-18  9:28 ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Change log:
Since v5:
Fix up DT bindings comments for TI HBMC driver
Move calibration sequence out of core into TI HBMC driver

Since v4:
Fix Rob's comments on dt-bindings of TI HBMC driver

Since v3:
* Drop reading QRY string twice in hyperbus_calibrate()
* Fix doc/misc comments on v3.

Since RFC v2:
* use map_word_xxx() for handling status register to support interleaved
  flashes as suggested by Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
* Report error status/messages on erase/program failure by looking at
  status register bits.
* Add "cfi-flash" as fallback compatible for cypress,hyperflash
* Add support to select between HyperBus and OSPI using mmio mux

Since RFC v1:
* Re-work Hyperbus core to provide separate struct representation for
  controller and slave devices
* Rename all files and func names to have hyperbus_ prefix
* Provide default calibration routine for use by controller drivers
* Fix up errors with patch spliting
* Address comments by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>


Cypress HyperBus is Low Signal Count, High Performance Double Data Rate Bus
interface between a host system master and one or more slave interfaces.
HyperBus is used to connect microprocessor, microcontroller, or ASIC
devices with random access NOR flash memory(called HyperFlash) or
self refresh DRAM(called HyperRAM).

Its a 8-bit data bus (DQ[7:0]) with  Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].

HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since Hyperbus is x8 DDR bus,
its equivalent to x16 parallel NOR flash wrt bits per clk. But Hyperbus
operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.
Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller(HBMC) drivers call hyperbus_register_device() to register a
single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.

This is an early RFC, to know if its okay to use maps framework and existing
CFI compliant flash support code to support Hyperflash
Also would like input on different types of HBMC master IPs out there
and their programming sequences.
Would appreciate any testing/review.

Tested on modified TI AM654 EVM with Cypress Hyperflash S26KS512 by
creating a UBIFS partition and writing and reading files to it.
Stress tested by writing/reading 16MB flash repeatedly at different
offsets using dd commmand.

HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]
TI's HBMC controller details at[3]

[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
    Table 12-5741. HyperFlash Access Sequence


Vignesh Raghavendra (5):
  mtd: cfi_cmdset_0002: Add support for polling status register
  dt-bindings: mtd: Add binding documentation for HyperFlash
  mtd: Add support for HyperBus memory devices
  dt-bindings: mtd: Add bindings for TI's AM654 HyperBus memory
    controller
  mtd: hyperbus: Add driver for TI's HyperBus memory controller

 .../bindings/mtd/cypress,hyperflash.txt       |  13 ++
 .../devicetree/bindings/mtd/ti,am654-hbmc.txt |  51 ++++++
 MAINTAINERS                                   |   8 +
 drivers/mtd/Kconfig                           |   2 +
 drivers/mtd/Makefile                          |   1 +
 drivers/mtd/chips/cfi_cmdset_0002.c           |  90 ++++++++++
 drivers/mtd/hyperbus/Kconfig                  |  23 +++
 drivers/mtd/hyperbus/Makefile                 |   4 +
 drivers/mtd/hyperbus/hbmc-am654.c             | 141 ++++++++++++++++
 drivers/mtd/hyperbus/hyperbus-core.c          | 154 ++++++++++++++++++
 include/linux/mtd/cfi.h                       |   5 +
 include/linux/mtd/hyperbus.h                  |  86 ++++++++++
 12 files changed, 578 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
 create mode 100644 Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
 create mode 100644 drivers/mtd/hyperbus/Kconfig
 create mode 100644 drivers/mtd/hyperbus/Makefile
 create mode 100644 drivers/mtd/hyperbus/hbmc-am654.c
 create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c
 create mode 100644 include/linux/mtd/hyperbus.h

-- 
2.21.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 24+ messages in thread
* [PATCH v6 0/5] MTD: Add Initial Hyperbus support
@ 2019-06-18  9:28 ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Change log:
Since v5:
Fix up DT bindings comments for TI HBMC driver
Move calibration sequence out of core into TI HBMC driver

Since v4:
Fix Rob's comments on dt-bindings of TI HBMC driver

Since v3:
* Drop reading QRY string twice in hyperbus_calibrate()
* Fix doc/misc comments on v3.

Since RFC v2:
* use map_word_xxx() for handling status register to support interleaved
  flashes as suggested by Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
* Report error status/messages on erase/program failure by looking at
  status register bits.
* Add "cfi-flash" as fallback compatible for cypress,hyperflash
* Add support to select between HyperBus and OSPI using mmio mux

Since RFC v1:
* Re-work Hyperbus core to provide separate struct representation for
  controller and slave devices
* Rename all files and func names to have hyperbus_ prefix
* Provide default calibration routine for use by controller drivers
* Fix up errors with patch spliting
* Address comments by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>


Cypress HyperBus is Low Signal Count, High Performance Double Data Rate Bus
interface between a host system master and one or more slave interfaces.
HyperBus is used to connect microprocessor, microcontroller, or ASIC
devices with random access NOR flash memory(called HyperFlash) or
self refresh DRAM(called HyperRAM).

Its a 8-bit data bus (DQ[7:0]) with  Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].

HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since Hyperbus is x8 DDR bus,
its equivalent to x16 parallel NOR flash wrt bits per clk. But Hyperbus
operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.
Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller(HBMC) drivers call hyperbus_register_device() to register a
single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.

This is an early RFC, to know if its okay to use maps framework and existing
CFI compliant flash support code to support Hyperflash
Also would like input on different types of HBMC master IPs out there
and their programming sequences.
Would appreciate any testing/review.

Tested on modified TI AM654 EVM with Cypress Hyperflash S26KS512 by
creating a UBIFS partition and writing and reading files to it.
Stress tested by writing/reading 16MB flash repeatedly at different
offsets using dd commmand.

HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]
TI's HBMC controller details at[3]

[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
    Table 12-5741. HyperFlash Access Sequence


Vignesh Raghavendra (5):
  mtd: cfi_cmdset_0002: Add support for polling status register
  dt-bindings: mtd: Add binding documentation for HyperFlash
  mtd: Add support for HyperBus memory devices
  dt-bindings: mtd: Add bindings for TI's AM654 HyperBus memory
    controller
  mtd: hyperbus: Add driver for TI's HyperBus memory controller

 .../bindings/mtd/cypress,hyperflash.txt       |  13 ++
 .../devicetree/bindings/mtd/ti,am654-hbmc.txt |  51 ++++++
 MAINTAINERS                                   |   8 +
 drivers/mtd/Kconfig                           |   2 +
 drivers/mtd/Makefile                          |   1 +
 drivers/mtd/chips/cfi_cmdset_0002.c           |  90 ++++++++++
 drivers/mtd/hyperbus/Kconfig                  |  23 +++
 drivers/mtd/hyperbus/Makefile                 |   4 +
 drivers/mtd/hyperbus/hbmc-am654.c             | 141 ++++++++++++++++
 drivers/mtd/hyperbus/hyperbus-core.c          | 154 ++++++++++++++++++
 include/linux/mtd/cfi.h                       |   5 +
 include/linux/mtd/hyperbus.h                  |  86 ++++++++++
 12 files changed, 578 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
 create mode 100644 Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
 create mode 100644 drivers/mtd/hyperbus/Kconfig
 create mode 100644 drivers/mtd/hyperbus/Makefile
 create mode 100644 drivers/mtd/hyperbus/hbmc-am654.c
 create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c
 create mode 100644 include/linux/mtd/hyperbus.h

-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 24+ messages in thread
* [PATCH v6 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
  2019-06-18  9:28 ` Vignesh Raghavendra
  (?)
  (?)
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  -1 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command
Set (0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.c can be used as is. But these devices
do not support DQ polling method of determining chip ready/good status.
These flashes provide Status Register whose bits can be polled to know
status of flash operation.

Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu
Extended Query version 1.5. Bit 0 of "Software Features supported" field
of CFI Primary Vendor-Specific Extended Query table indicates
presence/absence of status register and Bit 1 indicates whether or not
DQ polling is supported. Using these bits, its possible to determine
whether flash supports DQ polling or need to use Status Register.

Add support for polling Status Register to know device ready/status of
erase/write operations when DQ polling is not supported.
Print error messages on erase/program failure by looking at related
Status Register bits.

[1] https://www.cypress.com/file/213346/download

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---

v6: no change

 drivers/mtd/chips/cfi_cmdset_0002.c | 90 +++++++++++++++++++++++++++++
 include/linux/mtd/cfi.h             |  5 ++
 2 files changed, 95 insertions(+)

diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c
index c8fa5906bdf9..0f571f162e3b 100644
--- a/drivers/mtd/chips/cfi_cmdset_0002.c
+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -49,6 +49,16 @@
 #define SST49LF008A		0x005a
 #define AT49BV6416		0x00d6
 
+/*
+ * Status Register bit description. Used by flash devices that don't
+ * support DQ polling (e.g. HyperFlash)
+ */
+#define CFI_SR_DRB		BIT(7)
+#define CFI_SR_ESB		BIT(5)
+#define CFI_SR_PSB		BIT(4)
+#define CFI_SR_WBASB		BIT(3)
+#define CFI_SR_SLSB		BIT(1)
+
 static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
 static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
 static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
@@ -97,6 +107,48 @@ static struct mtd_chip_driver cfi_amdstd_chipdrv = {
 	.module		= THIS_MODULE
 };
 
+/*
+ * Use status register to poll for Erase/write completion when DQ is not
+ * supported. This is indicated by Bit[1:0] of SoftwareFeatures field in
+ * CFI Primary Vendor-Specific Extended Query table 1.5
+ */
+static int cfi_use_status_reg(struct cfi_private *cfi)
+{
+	struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
+
+	return extp->MinorVersion >= '5' &&
+		(extp->SoftwareFeatures & 0x3) == 0x1;
+}
+
+static void cfi_check_err_status(struct map_info *map, unsigned long adr)
+{
+	struct cfi_private *cfi = map->fldrv_priv;
+	map_word status;
+
+	if (!cfi_use_status_reg(cfi))
+		return;
+
+	cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+			 cfi->device_type, NULL);
+	status = map_read(map, adr);
+
+	if (map_word_bitsset(map, status, CMD(0x3a))) {
+		unsigned long chipstatus = MERGESTATUS(status);
+
+		if (chipstatus & CFI_SR_ESB)
+			pr_err("%s erase operation failed, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_PSB)
+			pr_err("%s program operation failed, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_WBASB)
+			pr_err("%s buffer program command aborted, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_SLSB)
+			pr_err("%s sector write protected, status %lx\n",
+			       map->name, chipstatus);
+	}
+}
 
 /* #define DEBUG_CFI_FEATURES */
 
@@ -744,8 +796,22 @@ static struct mtd_info *cfi_amdstd_setup(struct mtd_info *mtd)
  */
 static int __xipram chip_ready(struct map_info *map, unsigned long addr)
 {
+	struct cfi_private *cfi = map->fldrv_priv;
 	map_word d, t;
 
+	if (cfi_use_status_reg(cfi)) {
+		map_word ready = CMD(CFI_SR_DRB);
+		/*
+		 * For chips that support status register, check device
+		 * ready bit
+		 */
+		cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+				 cfi->device_type, NULL);
+		d = map_read(map, addr);
+
+		return map_word_andequal(map, d, ready, ready);
+	}
+
 	d = map_read(map, addr);
 	t = map_read(map, addr);
 
@@ -769,8 +835,27 @@ static int __xipram chip_ready(struct map_info *map, unsigned long addr)
  */
 static int __xipram chip_good(struct map_info *map, unsigned long addr, map_word expected)
 {
+	struct cfi_private *cfi = map->fldrv_priv;
 	map_word oldd, curd;
 
+	if (cfi_use_status_reg(cfi)) {
+		map_word ready = CMD(CFI_SR_DRB);
+		map_word err = CMD(CFI_SR_PSB | CFI_SR_ESB);
+		/*
+		 * For chips that support status register, check device
+		 * ready bit and Erase/Program status bit to know if
+		 * operation succeeded.
+		 */
+		cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+				 cfi->device_type, NULL);
+		curd = map_read(map, addr);
+
+		if (map_word_andequal(map, curd, ready, ready))
+			return !map_word_bitsset(map, curd, err);
+
+		return 0;
+	}
+
 	oldd = map_read(map, addr);
 	curd = map_read(map, addr);
 
@@ -1644,6 +1729,7 @@ static int __xipram do_write_oneword(struct map_info *map, struct flchip *chip,
 	/* Did we succeed? */
 	if (!chip_good(map, adr, datum)) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -1901,6 +1987,7 @@ static int __xipram do_write_buffer(struct map_info *map, struct flchip *chip,
 	 * See e.g.
 	 * http://www.spansion.com/Support/Application%20Notes/MirrorBit_Write_Buffer_Prog_Page_Buffer_Read_AN.pdf
 	 */
+	cfi_check_err_status(map, adr);
 	cfi_send_gen_cmd(0xAA, cfi->addr_unlock1, chip->start, map, cfi,
 			 cfi->device_type, NULL);
 	cfi_send_gen_cmd(0x55, cfi->addr_unlock2, chip->start, map, cfi,
@@ -2107,6 +2194,7 @@ static int do_panic_write_oneword(struct map_info *map, struct flchip *chip,
 
 	if (!chip_good(map, adr, datum)) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -2316,6 +2404,7 @@ static int __xipram do_erase_chip(struct map_info *map, struct flchip *chip)
 	/* Did we succeed? */
 	if (ret) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -2412,6 +2501,7 @@ static int __xipram do_erase_oneblock(struct map_info *map, struct flchip *chip,
 	/* Did we succeed? */
 	if (ret) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
diff --git a/include/linux/mtd/cfi.h b/include/linux/mtd/cfi.h
index 208c87cf2e3e..b50416169049 100644
--- a/include/linux/mtd/cfi.h
+++ b/include/linux/mtd/cfi.h
@@ -219,6 +219,11 @@ struct cfi_pri_amdstd {
 	uint8_t  VppMin;
 	uint8_t  VppMax;
 	uint8_t  TopBottom;
+	/* Below field are added from version 1.5 */
+	uint8_t  ProgramSuspend;
+	uint8_t  UnlockBypass;
+	uint8_t  SecureSiliconSector;
+	uint8_t  SoftwareFeatures;
 } __packed;
 
 /* Vendor-Specific PRI for Atmel chips (command set 0x0002) */
-- 
2.21.0


^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command
Set (0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.c can be used as is. But these devices
do not support DQ polling method of determining chip ready/good status.
These flashes provide Status Register whose bits can be polled to know
status of flash operation.

Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu
Extended Query version 1.5. Bit 0 of "Software Features supported" field
of CFI Primary Vendor-Specific Extended Query table indicates
presence/absence of status register and Bit 1 indicates whether or not
DQ polling is supported. Using these bits, its possible to determine
whether flash supports DQ polling or need to use Status Register.

Add support for polling Status Register to know device ready/status of
erase/write operations when DQ polling is not supported.
Print error messages on erase/program failure by looking at related
Status Register bits.

[1] https://www.cypress.com/file/213346/download

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---

v6: no change

 drivers/mtd/chips/cfi_cmdset_0002.c | 90 +++++++++++++++++++++++++++++
 include/linux/mtd/cfi.h             |  5 ++
 2 files changed, 95 insertions(+)

diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c
index c8fa5906bdf9..0f571f162e3b 100644
--- a/drivers/mtd/chips/cfi_cmdset_0002.c
+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -49,6 +49,16 @@
 #define SST49LF008A		0x005a
 #define AT49BV6416		0x00d6
 
+/*
+ * Status Register bit description. Used by flash devices that don't
+ * support DQ polling (e.g. HyperFlash)
+ */
+#define CFI_SR_DRB		BIT(7)
+#define CFI_SR_ESB		BIT(5)
+#define CFI_SR_PSB		BIT(4)
+#define CFI_SR_WBASB		BIT(3)
+#define CFI_SR_SLSB		BIT(1)
+
 static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
 static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
 static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
@@ -97,6 +107,48 @@ static struct mtd_chip_driver cfi_amdstd_chipdrv = {
 	.module		= THIS_MODULE
 };
 
+/*
+ * Use status register to poll for Erase/write completion when DQ is not
+ * supported. This is indicated by Bit[1:0] of SoftwareFeatures field in
+ * CFI Primary Vendor-Specific Extended Query table 1.5
+ */
+static int cfi_use_status_reg(struct cfi_private *cfi)
+{
+	struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
+
+	return extp->MinorVersion >= '5' &&
+		(extp->SoftwareFeatures & 0x3) == 0x1;
+}
+
+static void cfi_check_err_status(struct map_info *map, unsigned long adr)
+{
+	struct cfi_private *cfi = map->fldrv_priv;
+	map_word status;
+
+	if (!cfi_use_status_reg(cfi))
+		return;
+
+	cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+			 cfi->device_type, NULL);
+	status = map_read(map, adr);
+
+	if (map_word_bitsset(map, status, CMD(0x3a))) {
+		unsigned long chipstatus = MERGESTATUS(status);
+
+		if (chipstatus & CFI_SR_ESB)
+			pr_err("%s erase operation failed, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_PSB)
+			pr_err("%s program operation failed, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_WBASB)
+			pr_err("%s buffer program command aborted, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_SLSB)
+			pr_err("%s sector write protected, status %lx\n",
+			       map->name, chipstatus);
+	}
+}
 
 /* #define DEBUG_CFI_FEATURES */
 
@@ -744,8 +796,22 @@ static struct mtd_info *cfi_amdstd_setup(struct mtd_info *mtd)
  */
 static int __xipram chip_ready(struct map_info *map, unsigned long addr)
 {
+	struct cfi_private *cfi = map->fldrv_priv;
 	map_word d, t;
 
+	if (cfi_use_status_reg(cfi)) {
+		map_word ready = CMD(CFI_SR_DRB);
+		/*
+		 * For chips that support status register, check device
+		 * ready bit
+		 */
+		cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+				 cfi->device_type, NULL);
+		d = map_read(map, addr);
+
+		return map_word_andequal(map, d, ready, ready);
+	}
+
 	d = map_read(map, addr);
 	t = map_read(map, addr);
 
@@ -769,8 +835,27 @@ static int __xipram chip_ready(struct map_info *map, unsigned long addr)
  */
 static int __xipram chip_good(struct map_info *map, unsigned long addr, map_word expected)
 {
+	struct cfi_private *cfi = map->fldrv_priv;
 	map_word oldd, curd;
 
+	if (cfi_use_status_reg(cfi)) {
+		map_word ready = CMD(CFI_SR_DRB);
+		map_word err = CMD(CFI_SR_PSB | CFI_SR_ESB);
+		/*
+		 * For chips that support status register, check device
+		 * ready bit and Erase/Program status bit to know if
+		 * operation succeeded.
+		 */
+		cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+				 cfi->device_type, NULL);
+		curd = map_read(map, addr);
+
+		if (map_word_andequal(map, curd, ready, ready))
+			return !map_word_bitsset(map, curd, err);
+
+		return 0;
+	}
+
 	oldd = map_read(map, addr);
 	curd = map_read(map, addr);
 
@@ -1644,6 +1729,7 @@ static int __xipram do_write_oneword(struct map_info *map, struct flchip *chip,
 	/* Did we succeed? */
 	if (!chip_good(map, adr, datum)) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -1901,6 +1987,7 @@ static int __xipram do_write_buffer(struct map_info *map, struct flchip *chip,
 	 * See e.g.
 	 * http://www.spansion.com/Support/Application%20Notes/MirrorBit_Write_Buffer_Prog_Page_Buffer_Read_AN.pdf
 	 */
+	cfi_check_err_status(map, adr);
 	cfi_send_gen_cmd(0xAA, cfi->addr_unlock1, chip->start, map, cfi,
 			 cfi->device_type, NULL);
 	cfi_send_gen_cmd(0x55, cfi->addr_unlock2, chip->start, map, cfi,
@@ -2107,6 +2194,7 @@ static int do_panic_write_oneword(struct map_info *map, struct flchip *chip,
 
 	if (!chip_good(map, adr, datum)) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -2316,6 +2404,7 @@ static int __xipram do_erase_chip(struct map_info *map, struct flchip *chip)
 	/* Did we succeed? */
 	if (ret) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -2412,6 +2501,7 @@ static int __xipram do_erase_oneblock(struct map_info *map, struct flchip *chip,
 	/* Did we succeed? */
 	if (ret) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
diff --git a/include/linux/mtd/cfi.h b/include/linux/mtd/cfi.h
index 208c87cf2e3e..b50416169049 100644
--- a/include/linux/mtd/cfi.h
+++ b/include/linux/mtd/cfi.h
@@ -219,6 +219,11 @@ struct cfi_pri_amdstd {
 	uint8_t  VppMin;
 	uint8_t  VppMax;
 	uint8_t  TopBottom;
+	/* Below field are added from version 1.5 */
+	uint8_t  ProgramSuspend;
+	uint8_t  UnlockBypass;
+	uint8_t  SecureSiliconSector;
+	uint8_t  SoftwareFeatures;
 } __packed;
 
 /* Vendor-Specific PRI for Atmel chips (command set 0x0002) */
-- 
2.21.0

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command
Set (0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.c can be used as is. But these devices
do not support DQ polling method of determining chip ready/good status.
These flashes provide Status Register whose bits can be polled to know
status of flash operation.

Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu
Extended Query version 1.5. Bit 0 of "Software Features supported" field
of CFI Primary Vendor-Specific Extended Query table indicates
presence/absence of status register and Bit 1 indicates whether or not
DQ polling is supported. Using these bits, its possible to determine
whether flash supports DQ polling or need to use Status Register.

Add support for polling Status Register to know device ready/status of
erase/write operations when DQ polling is not supported.
Print error messages on erase/program failure by looking at related
Status Register bits.

[1] https://www.cypress.com/file/213346/download

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---

v6: no change

 drivers/mtd/chips/cfi_cmdset_0002.c | 90 +++++++++++++++++++++++++++++
 include/linux/mtd/cfi.h             |  5 ++
 2 files changed, 95 insertions(+)

diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c
index c8fa5906bdf9..0f571f162e3b 100644
--- a/drivers/mtd/chips/cfi_cmdset_0002.c
+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -49,6 +49,16 @@
 #define SST49LF008A		0x005a
 #define AT49BV6416		0x00d6
 
+/*
+ * Status Register bit description. Used by flash devices that don't
+ * support DQ polling (e.g. HyperFlash)
+ */
+#define CFI_SR_DRB		BIT(7)
+#define CFI_SR_ESB		BIT(5)
+#define CFI_SR_PSB		BIT(4)
+#define CFI_SR_WBASB		BIT(3)
+#define CFI_SR_SLSB		BIT(1)
+
 static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
 static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
 static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
@@ -97,6 +107,48 @@ static struct mtd_chip_driver cfi_amdstd_chipdrv = {
 	.module		= THIS_MODULE
 };
 
+/*
+ * Use status register to poll for Erase/write completion when DQ is not
+ * supported. This is indicated by Bit[1:0] of SoftwareFeatures field in
+ * CFI Primary Vendor-Specific Extended Query table 1.5
+ */
+static int cfi_use_status_reg(struct cfi_private *cfi)
+{
+	struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
+
+	return extp->MinorVersion >= '5' &&
+		(extp->SoftwareFeatures & 0x3) == 0x1;
+}
+
+static void cfi_check_err_status(struct map_info *map, unsigned long adr)
+{
+	struct cfi_private *cfi = map->fldrv_priv;
+	map_word status;
+
+	if (!cfi_use_status_reg(cfi))
+		return;
+
+	cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+			 cfi->device_type, NULL);
+	status = map_read(map, adr);
+
+	if (map_word_bitsset(map, status, CMD(0x3a))) {
+		unsigned long chipstatus = MERGESTATUS(status);
+
+		if (chipstatus & CFI_SR_ESB)
+			pr_err("%s erase operation failed, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_PSB)
+			pr_err("%s program operation failed, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_WBASB)
+			pr_err("%s buffer program command aborted, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_SLSB)
+			pr_err("%s sector write protected, status %lx\n",
+			       map->name, chipstatus);
+	}
+}
 
 /* #define DEBUG_CFI_FEATURES */
 
@@ -744,8 +796,22 @@ static struct mtd_info *cfi_amdstd_setup(struct mtd_info *mtd)
  */
 static int __xipram chip_ready(struct map_info *map, unsigned long addr)
 {
+	struct cfi_private *cfi = map->fldrv_priv;
 	map_word d, t;
 
+	if (cfi_use_status_reg(cfi)) {
+		map_word ready = CMD(CFI_SR_DRB);
+		/*
+		 * For chips that support status register, check device
+		 * ready bit
+		 */
+		cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+				 cfi->device_type, NULL);
+		d = map_read(map, addr);
+
+		return map_word_andequal(map, d, ready, ready);
+	}
+
 	d = map_read(map, addr);
 	t = map_read(map, addr);
 
@@ -769,8 +835,27 @@ static int __xipram chip_ready(struct map_info *map, unsigned long addr)
  */
 static int __xipram chip_good(struct map_info *map, unsigned long addr, map_word expected)
 {
+	struct cfi_private *cfi = map->fldrv_priv;
 	map_word oldd, curd;
 
+	if (cfi_use_status_reg(cfi)) {
+		map_word ready = CMD(CFI_SR_DRB);
+		map_word err = CMD(CFI_SR_PSB | CFI_SR_ESB);
+		/*
+		 * For chips that support status register, check device
+		 * ready bit and Erase/Program status bit to know if
+		 * operation succeeded.
+		 */
+		cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+				 cfi->device_type, NULL);
+		curd = map_read(map, addr);
+
+		if (map_word_andequal(map, curd, ready, ready))
+			return !map_word_bitsset(map, curd, err);
+
+		return 0;
+	}
+
 	oldd = map_read(map, addr);
 	curd = map_read(map, addr);
 
@@ -1644,6 +1729,7 @@ static int __xipram do_write_oneword(struct map_info *map, struct flchip *chip,
 	/* Did we succeed? */
 	if (!chip_good(map, adr, datum)) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -1901,6 +1987,7 @@ static int __xipram do_write_buffer(struct map_info *map, struct flchip *chip,
 	 * See e.g.
 	 * http://www.spansion.com/Support/Application%20Notes/MirrorBit_Write_Buffer_Prog_Page_Buffer_Read_AN.pdf
 	 */
+	cfi_check_err_status(map, adr);
 	cfi_send_gen_cmd(0xAA, cfi->addr_unlock1, chip->start, map, cfi,
 			 cfi->device_type, NULL);
 	cfi_send_gen_cmd(0x55, cfi->addr_unlock2, chip->start, map, cfi,
@@ -2107,6 +2194,7 @@ static int do_panic_write_oneword(struct map_info *map, struct flchip *chip,
 
 	if (!chip_good(map, adr, datum)) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -2316,6 +2404,7 @@ static int __xipram do_erase_chip(struct map_info *map, struct flchip *chip)
 	/* Did we succeed? */
 	if (ret) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -2412,6 +2501,7 @@ static int __xipram do_erase_oneblock(struct map_info *map, struct flchip *chip,
 	/* Did we succeed? */
 	if (ret) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
diff --git a/include/linux/mtd/cfi.h b/include/linux/mtd/cfi.h
index 208c87cf2e3e..b50416169049 100644
--- a/include/linux/mtd/cfi.h
+++ b/include/linux/mtd/cfi.h
@@ -219,6 +219,11 @@ struct cfi_pri_amdstd {
 	uint8_t  VppMin;
 	uint8_t  VppMax;
 	uint8_t  TopBottom;
+	/* Below field are added from version 1.5 */
+	uint8_t  ProgramSuspend;
+	uint8_t  UnlockBypass;
+	uint8_t  SecureSiliconSector;
+	uint8_t  SoftwareFeatures;
 } __packed;
 
 /* Vendor-Specific PRI for Atmel chips (command set 0x0002) */
-- 
2.21.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 1/5] mtd: cfi_cmdset_0002: Add support for polling status register
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command
Set (0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.c can be used as is. But these devices
do not support DQ polling method of determining chip ready/good status.
These flashes provide Status Register whose bits can be polled to know
status of flash operation.

Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu
Extended Query version 1.5. Bit 0 of "Software Features supported" field
of CFI Primary Vendor-Specific Extended Query table indicates
presence/absence of status register and Bit 1 indicates whether or not
DQ polling is supported. Using these bits, its possible to determine
whether flash supports DQ polling or need to use Status Register.

Add support for polling Status Register to know device ready/status of
erase/write operations when DQ polling is not supported.
Print error messages on erase/program failure by looking at related
Status Register bits.

[1] https://www.cypress.com/file/213346/download

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---

v6: no change

 drivers/mtd/chips/cfi_cmdset_0002.c | 90 +++++++++++++++++++++++++++++
 include/linux/mtd/cfi.h             |  5 ++
 2 files changed, 95 insertions(+)

diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c
index c8fa5906bdf9..0f571f162e3b 100644
--- a/drivers/mtd/chips/cfi_cmdset_0002.c
+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -49,6 +49,16 @@
 #define SST49LF008A		0x005a
 #define AT49BV6416		0x00d6
 
+/*
+ * Status Register bit description. Used by flash devices that don't
+ * support DQ polling (e.g. HyperFlash)
+ */
+#define CFI_SR_DRB		BIT(7)
+#define CFI_SR_ESB		BIT(5)
+#define CFI_SR_PSB		BIT(4)
+#define CFI_SR_WBASB		BIT(3)
+#define CFI_SR_SLSB		BIT(1)
+
 static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
 static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
 static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
@@ -97,6 +107,48 @@ static struct mtd_chip_driver cfi_amdstd_chipdrv = {
 	.module		= THIS_MODULE
 };
 
+/*
+ * Use status register to poll for Erase/write completion when DQ is not
+ * supported. This is indicated by Bit[1:0] of SoftwareFeatures field in
+ * CFI Primary Vendor-Specific Extended Query table 1.5
+ */
+static int cfi_use_status_reg(struct cfi_private *cfi)
+{
+	struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
+
+	return extp->MinorVersion >= '5' &&
+		(extp->SoftwareFeatures & 0x3) == 0x1;
+}
+
+static void cfi_check_err_status(struct map_info *map, unsigned long adr)
+{
+	struct cfi_private *cfi = map->fldrv_priv;
+	map_word status;
+
+	if (!cfi_use_status_reg(cfi))
+		return;
+
+	cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+			 cfi->device_type, NULL);
+	status = map_read(map, adr);
+
+	if (map_word_bitsset(map, status, CMD(0x3a))) {
+		unsigned long chipstatus = MERGESTATUS(status);
+
+		if (chipstatus & CFI_SR_ESB)
+			pr_err("%s erase operation failed, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_PSB)
+			pr_err("%s program operation failed, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_WBASB)
+			pr_err("%s buffer program command aborted, status %lx\n",
+			       map->name, chipstatus);
+		if (chipstatus & CFI_SR_SLSB)
+			pr_err("%s sector write protected, status %lx\n",
+			       map->name, chipstatus);
+	}
+}
 
 /* #define DEBUG_CFI_FEATURES */
 
@@ -744,8 +796,22 @@ static struct mtd_info *cfi_amdstd_setup(struct mtd_info *mtd)
  */
 static int __xipram chip_ready(struct map_info *map, unsigned long addr)
 {
+	struct cfi_private *cfi = map->fldrv_priv;
 	map_word d, t;
 
+	if (cfi_use_status_reg(cfi)) {
+		map_word ready = CMD(CFI_SR_DRB);
+		/*
+		 * For chips that support status register, check device
+		 * ready bit
+		 */
+		cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+				 cfi->device_type, NULL);
+		d = map_read(map, addr);
+
+		return map_word_andequal(map, d, ready, ready);
+	}
+
 	d = map_read(map, addr);
 	t = map_read(map, addr);
 
@@ -769,8 +835,27 @@ static int __xipram chip_ready(struct map_info *map, unsigned long addr)
  */
 static int __xipram chip_good(struct map_info *map, unsigned long addr, map_word expected)
 {
+	struct cfi_private *cfi = map->fldrv_priv;
 	map_word oldd, curd;
 
+	if (cfi_use_status_reg(cfi)) {
+		map_word ready = CMD(CFI_SR_DRB);
+		map_word err = CMD(CFI_SR_PSB | CFI_SR_ESB);
+		/*
+		 * For chips that support status register, check device
+		 * ready bit and Erase/Program status bit to know if
+		 * operation succeeded.
+		 */
+		cfi_send_gen_cmd(0x70, cfi->addr_unlock1, 0, map, cfi,
+				 cfi->device_type, NULL);
+		curd = map_read(map, addr);
+
+		if (map_word_andequal(map, curd, ready, ready))
+			return !map_word_bitsset(map, curd, err);
+
+		return 0;
+	}
+
 	oldd = map_read(map, addr);
 	curd = map_read(map, addr);
 
@@ -1644,6 +1729,7 @@ static int __xipram do_write_oneword(struct map_info *map, struct flchip *chip,
 	/* Did we succeed? */
 	if (!chip_good(map, adr, datum)) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -1901,6 +1987,7 @@ static int __xipram do_write_buffer(struct map_info *map, struct flchip *chip,
 	 * See e.g.
 	 * http://www.spansion.com/Support/Application%20Notes/MirrorBit_Write_Buffer_Prog_Page_Buffer_Read_AN.pdf
 	 */
+	cfi_check_err_status(map, adr);
 	cfi_send_gen_cmd(0xAA, cfi->addr_unlock1, chip->start, map, cfi,
 			 cfi->device_type, NULL);
 	cfi_send_gen_cmd(0x55, cfi->addr_unlock2, chip->start, map, cfi,
@@ -2107,6 +2194,7 @@ static int do_panic_write_oneword(struct map_info *map, struct flchip *chip,
 
 	if (!chip_good(map, adr, datum)) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -2316,6 +2404,7 @@ static int __xipram do_erase_chip(struct map_info *map, struct flchip *chip)
 	/* Did we succeed? */
 	if (ret) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
@@ -2412,6 +2501,7 @@ static int __xipram do_erase_oneblock(struct map_info *map, struct flchip *chip,
 	/* Did we succeed? */
 	if (ret) {
 		/* reset on all failures. */
+		cfi_check_err_status(map, adr);
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
diff --git a/include/linux/mtd/cfi.h b/include/linux/mtd/cfi.h
index 208c87cf2e3e..b50416169049 100644
--- a/include/linux/mtd/cfi.h
+++ b/include/linux/mtd/cfi.h
@@ -219,6 +219,11 @@ struct cfi_pri_amdstd {
 	uint8_t  VppMin;
 	uint8_t  VppMax;
 	uint8_t  TopBottom;
+	/* Below field are added from version 1.5 */
+	uint8_t  ProgramSuspend;
+	uint8_t  UnlockBypass;
+	uint8_t  SecureSiliconSector;
+	uint8_t  SoftwareFeatures;
 } __packed;
 
 /* Vendor-Specific PRI for Atmel chips (command set 0x0002) */
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 2/5] dt-bindings: mtd: Add binding documentation for HyperFlash
  2019-06-18  9:28 ` Vignesh Raghavendra
  (?)
  (?)
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  -1 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

Add DT binding documentation for HyperFlash devices.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---

v6: No change

 .../devicetree/bindings/mtd/cypress,hyperflash.txt  | 13 +++++++++++++
 1 file changed, 13 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt

diff --git a/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt b/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
new file mode 100644
index 000000000000..ad42f4db32f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
@@ -0,0 +1,13 @@
+Bindings for HyperFlash NOR flash chips compliant with Cypress HyperBus
+specification and supports Cypress CFI specification 1.5 command set.
+
+Required properties:
+- compatible : "cypress,hyperflash", "cfi-flash" for HyperFlash NOR chips
+- reg : Address of flash's memory map
+
+Example:
+
+	flash@0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0x0 0x4000000>;
+	};
-- 
2.21.0


^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 2/5] dt-bindings: mtd: Add binding documentation for HyperFlash
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

Add DT binding documentation for HyperFlash devices.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---

v6: No change

 .../devicetree/bindings/mtd/cypress,hyperflash.txt  | 13 +++++++++++++
 1 file changed, 13 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt

diff --git a/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt b/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
new file mode 100644
index 000000000000..ad42f4db32f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
@@ -0,0 +1,13 @@
+Bindings for HyperFlash NOR flash chips compliant with Cypress HyperBus
+specification and supports Cypress CFI specification 1.5 command set.
+
+Required properties:
+- compatible : "cypress,hyperflash", "cfi-flash" for HyperFlash NOR chips
+- reg : Address of flash's memory map
+
+Example:
+
+	flash@0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0x0 0x4000000>;
+	};
-- 
2.21.0

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 2/5] dt-bindings: mtd: Add binding documentation for HyperFlash
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Add DT binding documentation for HyperFlash devices.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---

v6: No change

 .../devicetree/bindings/mtd/cypress,hyperflash.txt  | 13 +++++++++++++
 1 file changed, 13 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt

diff --git a/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt b/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
new file mode 100644
index 000000000000..ad42f4db32f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
@@ -0,0 +1,13 @@
+Bindings for HyperFlash NOR flash chips compliant with Cypress HyperBus
+specification and supports Cypress CFI specification 1.5 command set.
+
+Required properties:
+- compatible : "cypress,hyperflash", "cfi-flash" for HyperFlash NOR chips
+- reg : Address of flash's memory map
+
+Example:
+
+	flash@0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0x0 0x4000000>;
+	};
-- 
2.21.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 2/5] dt-bindings: mtd: Add binding documentation for HyperFlash
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Add DT binding documentation for HyperFlash devices.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---

v6: No change

 .../devicetree/bindings/mtd/cypress,hyperflash.txt  | 13 +++++++++++++
 1 file changed, 13 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt

diff --git a/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt b/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
new file mode 100644
index 000000000000..ad42f4db32f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
@@ -0,0 +1,13 @@
+Bindings for HyperFlash NOR flash chips compliant with Cypress HyperBus
+specification and supports Cypress CFI specification 1.5 command set.
+
+Required properties:
+- compatible : "cypress,hyperflash", "cfi-flash" for HyperFlash NOR chips
+- reg : Address of flash's memory map
+
+Example:
+
+	flash@0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0x0 0x4000000>;
+	};
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 3/5] mtd: Add support for HyperBus memory devices
  2019-06-18  9:28 ` Vignesh Raghavendra
  (?)
  (?)
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  -1 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

Cypress' HyperBus is Low Signal Count, High Performance Double Data Rate
Bus interface between a host system master and one or more slave
interfaces. HyperBus is used to connect microprocessor, microcontroller,
or ASIC devices with random access NOR flash memory (called HyperFlash)
or self refresh DRAM (called HyperRAM).

Its a 8-bit data bus (DQ[7:0]) with  Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].

HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since HyperBus is x8 DDR bus,
its equivalent to x16 parallel NOR flash wrt bits per clock cycle. But
HyperBus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.

But, HyperBus memory controllers seem to abstract implementation details
and expose a simple MMIO interface to access connected flash.

Add support for registering HyperFlash devices with MTD framework. MTD
maps framework along with CFI chip support framework are used to support
communicating with flash.

Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller (HBMC) drivers calls hyperbus_register_device() to
register a single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.

HyperRAM is not supported at the moment.

HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]

[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
    Table 12-5741. HyperFlash Access Sequence

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6:
Clarify read16()/write16() APIs
Move calibration code out into TI specific driver

 MAINTAINERS                          |   7 ++
 drivers/mtd/Kconfig                  |   2 +
 drivers/mtd/Makefile                 |   1 +
 drivers/mtd/hyperbus/Kconfig         |  11 ++
 drivers/mtd/hyperbus/Makefile        |   3 +
 drivers/mtd/hyperbus/hyperbus-core.c | 154 +++++++++++++++++++++++++++
 include/linux/mtd/hyperbus.h         |  86 +++++++++++++++
 7 files changed, 264 insertions(+)
 create mode 100644 drivers/mtd/hyperbus/Kconfig
 create mode 100644 drivers/mtd/hyperbus/Makefile
 create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c
 create mode 100644 include/linux/mtd/hyperbus.h

diff --git a/MAINTAINERS b/MAINTAINERS
index ff7c2b7e67b9..58c6ad3dae66 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7353,6 +7353,13 @@ F:	include/asm-generic/mshyperv.h
 F:	tools/hv/
 F:	Documentation/ABI/stable/sysfs-bus-vmbus
 
+HYPERBUS SUPPORT
+M:	Vignesh Raghavendra <vigneshr@ti.com>
+S:	Supported
+F:	drivers/mtd/hyperbus/
+F:	include/linux/mtd/hyperbus.h
+F:	Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
+
 HYPERVISOR VIRTUAL CONSOLE DRIVER
 L:	linuxppc-dev@lists.ozlabs.org
 S:	Odd Fixes
diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig
index fb31a7f649a3..80a6e2dcd085 100644
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -274,4 +274,6 @@ source "drivers/mtd/spi-nor/Kconfig"
 
 source "drivers/mtd/ubi/Kconfig"
 
+source "drivers/mtd/hyperbus/Kconfig"
+
 endif # MTD
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index 806287e80e84..62d649a959e2 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -34,3 +34,4 @@ obj-y		+= chips/ lpddr/ maps/ devices/ nand/ tests/
 
 obj-$(CONFIG_MTD_SPI_NOR)	+= spi-nor/
 obj-$(CONFIG_MTD_UBI)		+= ubi/
+obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus/
diff --git a/drivers/mtd/hyperbus/Kconfig b/drivers/mtd/hyperbus/Kconfig
new file mode 100644
index 000000000000..98147e28caa0
--- /dev/null
+++ b/drivers/mtd/hyperbus/Kconfig
@@ -0,0 +1,11 @@
+menuconfig MTD_HYPERBUS
+	tristate "HyperBus support"
+	select MTD_CFI
+	select MTD_MAP_BANK_WIDTH_2
+	select MTD_CFI_AMDSTD
+	select MTD_COMPLEX_MAPPINGS
+	help
+	  This is the framework for the HyperBus which can be used by
+	  the HyperBus Controller driver to communicate with
+	  HyperFlash. See Cypress HyperBus specification for more
+	  details
diff --git a/drivers/mtd/hyperbus/Makefile b/drivers/mtd/hyperbus/Makefile
new file mode 100644
index 000000000000..ca61dedd730d
--- /dev/null
+++ b/drivers/mtd/hyperbus/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus-core.o
diff --git a/drivers/mtd/hyperbus/hyperbus-core.c b/drivers/mtd/hyperbus/hyperbus-core.c
new file mode 100644
index 000000000000..63a9e64895bc
--- /dev/null
+++ b/drivers/mtd/hyperbus/hyperbus-core.c
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Author: Vignesh Raghavendra <vigneshr@ti.com>
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/hyperbus.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/mtd.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/types.h>
+
+static struct hyperbus_device *map_to_hbdev(struct map_info *map)
+{
+	return container_of(map, struct hyperbus_device, map);
+}
+
+static map_word hyperbus_read16(struct map_info *map, unsigned long addr)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+	map_word read_data;
+
+	read_data.x[0] = ctlr->ops->read16(hbdev, addr);
+
+	return read_data;
+}
+
+static void hyperbus_write16(struct map_info *map, map_word d,
+			     unsigned long addr)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->write16(hbdev, addr, d.x[0]);
+}
+
+static void hyperbus_copy_from(struct map_info *map, void *to,
+			       unsigned long from, ssize_t len)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->copy_from(hbdev, to, from, len);
+}
+
+static void hyperbus_copy_to(struct map_info *map, unsigned long to,
+			     const void *from, ssize_t len)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->copy_to(hbdev, to, from, len);
+}
+
+int hyperbus_register_device(struct hyperbus_device *hbdev)
+{
+	const struct hyperbus_ops *ops;
+	struct hyperbus_ctlr *ctlr;
+	struct device_node *np;
+	struct map_info *map;
+	struct resource res;
+	struct device *dev;
+	int ret;
+
+	if (!hbdev || !hbdev->np || !hbdev->ctlr || !hbdev->ctlr->dev) {
+		pr_err("hyperbus: please fill all the necessary fields!\n");
+		return -EINVAL;
+	}
+
+	np = hbdev->np;
+	ctlr = hbdev->ctlr;
+	if (!of_device_is_compatible(np, "cypress,hyperflash"))
+		return -ENODEV;
+
+	hbdev->memtype = HYPERFLASH;
+
+	ret = of_address_to_resource(np, 0, &res);
+	if (ret)
+		return ret;
+
+	dev = ctlr->dev;
+	map = &hbdev->map;
+	map->size = resource_size(&res);
+	map->virt = devm_ioremap_resource(dev, &res);
+	if (IS_ERR(map->virt))
+		return PTR_ERR(map->virt);
+
+	map->name = dev_name(dev);
+	map->bankwidth = 2;
+	map->device_node = np;
+
+	simple_map_init(map);
+	ops = ctlr->ops;
+	if (ops) {
+		if (ops->read16)
+			map->read = hyperbus_read16;
+		if (ops->write16)
+			map->write = hyperbus_write16;
+		if (ops->copy_to)
+			map->copy_to = hyperbus_copy_to;
+		if (ops->copy_from)
+			map->copy_from = hyperbus_copy_from;
+
+		if (ops->calibrate && !ctlr->calibrated) {
+			ret = ops->calibrate(hbdev);
+			if (!ret) {
+				dev_err(dev, "Calibration failed\n");
+				return -ENODEV;
+			}
+			ctlr->calibrated = true;
+		}
+	}
+
+	hbdev->mtd = do_map_probe("cfi_probe", map);
+	if (!hbdev->mtd) {
+		dev_err(dev, "probing of hyperbus device failed\n");
+		return -ENODEV;
+	}
+
+	hbdev->mtd->dev.parent = dev;
+	mtd_set_of_node(hbdev->mtd, np);
+
+	ret = mtd_device_register(hbdev->mtd, NULL, 0);
+	if (ret) {
+		dev_err(dev, "failed to register mtd device\n");
+		map_destroy(hbdev->mtd);
+		return ret;
+	}
+	hbdev->registered = true;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(hyperbus_register_device);
+
+int hyperbus_unregister_device(struct hyperbus_device *hbdev)
+{
+	int ret = 0;
+
+	if (hbdev && hbdev->mtd && hbdev->registered) {
+		ret = mtd_device_unregister(hbdev->mtd);
+		map_destroy(hbdev->mtd);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(hyperbus_unregister_device);
+
+MODULE_DESCRIPTION("HyperBus Framework");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>");
diff --git a/include/linux/mtd/hyperbus.h b/include/linux/mtd/hyperbus.h
new file mode 100644
index 000000000000..ead969aad35b
--- /dev/null
+++ b/include/linux/mtd/hyperbus.h
@@ -0,0 +1,86 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#ifndef __LINUX_MTD_HYPERBUS_H__
+#define __LINUX_MTD_HYPERBUS_H__
+
+#include <linux/mtd/map.h>
+
+enum hyperbus_memtype {
+	HYPERFLASH,
+	HYPERRAM,
+};
+
+/**
+ * struct hyperbus_device - struct representing HyperBus slave device
+ * @map: map_info struct for accessing MMIO HyperBus flash memory
+ * @np: pointer to HyperBus slave device node
+ * @mtd: pointer to MTD struct
+ * @ctlr: pointer to HyperBus controller struct
+ * @memtype: type of memory device: HyperFlash or HyperRAM
+ * @registered: flag to indicate whether device is registered with MTD core
+ */
+
+struct hyperbus_device {
+	struct map_info map;
+	struct device_node *np;
+	struct mtd_info *mtd;
+	struct hyperbus_ctlr *ctlr;
+	enum hyperbus_memtype memtype;
+	bool registered;
+};
+
+/**
+ * struct hyperbus_ops - struct representing custom HyperBus operations
+ * @read16: read 16 bit of data to flash in a single burst. Used to read
+ *          from non default address space, such as ID/CFI space
+ * @write16: write 16 bit of data to flash in a single burst. Used to
+ *           send cmd to flash or write single 16 bit word at a time
+ * @copy_from: copy data from flash memory
+ * @copy_to: copy data to flash memory
+ * @calibrate: calibrate HyperBus controller
+ */
+
+struct hyperbus_ops {
+	u16 (*read16)(struct hyperbus_device *hbdev, unsigned long addr);
+	void (*write16)(struct hyperbus_device *hbdev,
+			unsigned long addr, u16 val);
+	void (*copy_from)(struct hyperbus_device *hbdev, void *to,
+			  unsigned long from, ssize_t len);
+	void (*copy_to)(struct hyperbus_device *dev, unsigned long to,
+			const void *from, ssize_t len);
+	int (*calibrate)(struct hyperbus_device *dev);
+};
+
+/**
+ * struct hyperbus_ctlr - struct representing HyperBus controller
+ * @dev: pointer to HyperBus controller device
+ * @calibrated: flag to indicate ctlr calibration sequence is complete
+ * @ops: HyperBus controller ops
+ */
+struct hyperbus_ctlr {
+	struct device *dev;
+	bool calibrated;
+
+	const struct hyperbus_ops *ops;
+};
+
+/**
+ * hyperbus_register_device - probe and register a HyperBus slave memory device
+ * @hbdev: hyperbus_device struct with dev, np and ctlr field populated
+ *
+ * Return: 0 for success, others for failure.
+ */
+int hyperbus_register_device(struct hyperbus_device *hbdev);
+
+/**
+ * hyperbus_unregister_device - deregister HyperBus slave memory device
+ * @hbdev: hyperbus_device to be unregistered
+ *
+ * Return: 0 for success, others for failure.
+ */
+int hyperbus_unregister_device(struct hyperbus_device *hbdev);
+
+#endif /* __LINUX_MTD_HYPERBUS_H__ */
-- 
2.21.0


^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 3/5] mtd: Add support for HyperBus memory devices
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

Cypress' HyperBus is Low Signal Count, High Performance Double Data Rate
Bus interface between a host system master and one or more slave
interfaces. HyperBus is used to connect microprocessor, microcontroller,
or ASIC devices with random access NOR flash memory (called HyperFlash)
or self refresh DRAM (called HyperRAM).

Its a 8-bit data bus (DQ[7:0]) with  Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].

HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since HyperBus is x8 DDR bus,
its equivalent to x16 parallel NOR flash wrt bits per clock cycle. But
HyperBus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.

But, HyperBus memory controllers seem to abstract implementation details
and expose a simple MMIO interface to access connected flash.

Add support for registering HyperFlash devices with MTD framework. MTD
maps framework along with CFI chip support framework are used to support
communicating with flash.

Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller (HBMC) drivers calls hyperbus_register_device() to
register a single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.

HyperRAM is not supported at the moment.

HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]

[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
    Table 12-5741. HyperFlash Access Sequence

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6:
Clarify read16()/write16() APIs
Move calibration code out into TI specific driver

 MAINTAINERS                          |   7 ++
 drivers/mtd/Kconfig                  |   2 +
 drivers/mtd/Makefile                 |   1 +
 drivers/mtd/hyperbus/Kconfig         |  11 ++
 drivers/mtd/hyperbus/Makefile        |   3 +
 drivers/mtd/hyperbus/hyperbus-core.c | 154 +++++++++++++++++++++++++++
 include/linux/mtd/hyperbus.h         |  86 +++++++++++++++
 7 files changed, 264 insertions(+)
 create mode 100644 drivers/mtd/hyperbus/Kconfig
 create mode 100644 drivers/mtd/hyperbus/Makefile
 create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c
 create mode 100644 include/linux/mtd/hyperbus.h

diff --git a/MAINTAINERS b/MAINTAINERS
index ff7c2b7e67b9..58c6ad3dae66 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7353,6 +7353,13 @@ F:	include/asm-generic/mshyperv.h
 F:	tools/hv/
 F:	Documentation/ABI/stable/sysfs-bus-vmbus
 
+HYPERBUS SUPPORT
+M:	Vignesh Raghavendra <vigneshr@ti.com>
+S:	Supported
+F:	drivers/mtd/hyperbus/
+F:	include/linux/mtd/hyperbus.h
+F:	Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
+
 HYPERVISOR VIRTUAL CONSOLE DRIVER
 L:	linuxppc-dev@lists.ozlabs.org
 S:	Odd Fixes
diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig
index fb31a7f649a3..80a6e2dcd085 100644
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -274,4 +274,6 @@ source "drivers/mtd/spi-nor/Kconfig"
 
 source "drivers/mtd/ubi/Kconfig"
 
+source "drivers/mtd/hyperbus/Kconfig"
+
 endif # MTD
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index 806287e80e84..62d649a959e2 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -34,3 +34,4 @@ obj-y		+= chips/ lpddr/ maps/ devices/ nand/ tests/
 
 obj-$(CONFIG_MTD_SPI_NOR)	+= spi-nor/
 obj-$(CONFIG_MTD_UBI)		+= ubi/
+obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus/
diff --git a/drivers/mtd/hyperbus/Kconfig b/drivers/mtd/hyperbus/Kconfig
new file mode 100644
index 000000000000..98147e28caa0
--- /dev/null
+++ b/drivers/mtd/hyperbus/Kconfig
@@ -0,0 +1,11 @@
+menuconfig MTD_HYPERBUS
+	tristate "HyperBus support"
+	select MTD_CFI
+	select MTD_MAP_BANK_WIDTH_2
+	select MTD_CFI_AMDSTD
+	select MTD_COMPLEX_MAPPINGS
+	help
+	  This is the framework for the HyperBus which can be used by
+	  the HyperBus Controller driver to communicate with
+	  HyperFlash. See Cypress HyperBus specification for more
+	  details
diff --git a/drivers/mtd/hyperbus/Makefile b/drivers/mtd/hyperbus/Makefile
new file mode 100644
index 000000000000..ca61dedd730d
--- /dev/null
+++ b/drivers/mtd/hyperbus/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus-core.o
diff --git a/drivers/mtd/hyperbus/hyperbus-core.c b/drivers/mtd/hyperbus/hyperbus-core.c
new file mode 100644
index 000000000000..63a9e64895bc
--- /dev/null
+++ b/drivers/mtd/hyperbus/hyperbus-core.c
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Author: Vignesh Raghavendra <vigneshr@ti.com>
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/hyperbus.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/mtd.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/types.h>
+
+static struct hyperbus_device *map_to_hbdev(struct map_info *map)
+{
+	return container_of(map, struct hyperbus_device, map);
+}
+
+static map_word hyperbus_read16(struct map_info *map, unsigned long addr)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+	map_word read_data;
+
+	read_data.x[0] = ctlr->ops->read16(hbdev, addr);
+
+	return read_data;
+}
+
+static void hyperbus_write16(struct map_info *map, map_word d,
+			     unsigned long addr)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->write16(hbdev, addr, d.x[0]);
+}
+
+static void hyperbus_copy_from(struct map_info *map, void *to,
+			       unsigned long from, ssize_t len)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->copy_from(hbdev, to, from, len);
+}
+
+static void hyperbus_copy_to(struct map_info *map, unsigned long to,
+			     const void *from, ssize_t len)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->copy_to(hbdev, to, from, len);
+}
+
+int hyperbus_register_device(struct hyperbus_device *hbdev)
+{
+	const struct hyperbus_ops *ops;
+	struct hyperbus_ctlr *ctlr;
+	struct device_node *np;
+	struct map_info *map;
+	struct resource res;
+	struct device *dev;
+	int ret;
+
+	if (!hbdev || !hbdev->np || !hbdev->ctlr || !hbdev->ctlr->dev) {
+		pr_err("hyperbus: please fill all the necessary fields!\n");
+		return -EINVAL;
+	}
+
+	np = hbdev->np;
+	ctlr = hbdev->ctlr;
+	if (!of_device_is_compatible(np, "cypress,hyperflash"))
+		return -ENODEV;
+
+	hbdev->memtype = HYPERFLASH;
+
+	ret = of_address_to_resource(np, 0, &res);
+	if (ret)
+		return ret;
+
+	dev = ctlr->dev;
+	map = &hbdev->map;
+	map->size = resource_size(&res);
+	map->virt = devm_ioremap_resource(dev, &res);
+	if (IS_ERR(map->virt))
+		return PTR_ERR(map->virt);
+
+	map->name = dev_name(dev);
+	map->bankwidth = 2;
+	map->device_node = np;
+
+	simple_map_init(map);
+	ops = ctlr->ops;
+	if (ops) {
+		if (ops->read16)
+			map->read = hyperbus_read16;
+		if (ops->write16)
+			map->write = hyperbus_write16;
+		if (ops->copy_to)
+			map->copy_to = hyperbus_copy_to;
+		if (ops->copy_from)
+			map->copy_from = hyperbus_copy_from;
+
+		if (ops->calibrate && !ctlr->calibrated) {
+			ret = ops->calibrate(hbdev);
+			if (!ret) {
+				dev_err(dev, "Calibration failed\n");
+				return -ENODEV;
+			}
+			ctlr->calibrated = true;
+		}
+	}
+
+	hbdev->mtd = do_map_probe("cfi_probe", map);
+	if (!hbdev->mtd) {
+		dev_err(dev, "probing of hyperbus device failed\n");
+		return -ENODEV;
+	}
+
+	hbdev->mtd->dev.parent = dev;
+	mtd_set_of_node(hbdev->mtd, np);
+
+	ret = mtd_device_register(hbdev->mtd, NULL, 0);
+	if (ret) {
+		dev_err(dev, "failed to register mtd device\n");
+		map_destroy(hbdev->mtd);
+		return ret;
+	}
+	hbdev->registered = true;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(hyperbus_register_device);
+
+int hyperbus_unregister_device(struct hyperbus_device *hbdev)
+{
+	int ret = 0;
+
+	if (hbdev && hbdev->mtd && hbdev->registered) {
+		ret = mtd_device_unregister(hbdev->mtd);
+		map_destroy(hbdev->mtd);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(hyperbus_unregister_device);
+
+MODULE_DESCRIPTION("HyperBus Framework");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>");
diff --git a/include/linux/mtd/hyperbus.h b/include/linux/mtd/hyperbus.h
new file mode 100644
index 000000000000..ead969aad35b
--- /dev/null
+++ b/include/linux/mtd/hyperbus.h
@@ -0,0 +1,86 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#ifndef __LINUX_MTD_HYPERBUS_H__
+#define __LINUX_MTD_HYPERBUS_H__
+
+#include <linux/mtd/map.h>
+
+enum hyperbus_memtype {
+	HYPERFLASH,
+	HYPERRAM,
+};
+
+/**
+ * struct hyperbus_device - struct representing HyperBus slave device
+ * @map: map_info struct for accessing MMIO HyperBus flash memory
+ * @np: pointer to HyperBus slave device node
+ * @mtd: pointer to MTD struct
+ * @ctlr: pointer to HyperBus controller struct
+ * @memtype: type of memory device: HyperFlash or HyperRAM
+ * @registered: flag to indicate whether device is registered with MTD core
+ */
+
+struct hyperbus_device {
+	struct map_info map;
+	struct device_node *np;
+	struct mtd_info *mtd;
+	struct hyperbus_ctlr *ctlr;
+	enum hyperbus_memtype memtype;
+	bool registered;
+};
+
+/**
+ * struct hyperbus_ops - struct representing custom HyperBus operations
+ * @read16: read 16 bit of data to flash in a single burst. Used to read
+ *          from non default address space, such as ID/CFI space
+ * @write16: write 16 bit of data to flash in a single burst. Used to
+ *           send cmd to flash or write single 16 bit word at a time
+ * @copy_from: copy data from flash memory
+ * @copy_to: copy data to flash memory
+ * @calibrate: calibrate HyperBus controller
+ */
+
+struct hyperbus_ops {
+	u16 (*read16)(struct hyperbus_device *hbdev, unsigned long addr);
+	void (*write16)(struct hyperbus_device *hbdev,
+			unsigned long addr, u16 val);
+	void (*copy_from)(struct hyperbus_device *hbdev, void *to,
+			  unsigned long from, ssize_t len);
+	void (*copy_to)(struct hyperbus_device *dev, unsigned long to,
+			const void *from, ssize_t len);
+	int (*calibrate)(struct hyperbus_device *dev);
+};
+
+/**
+ * struct hyperbus_ctlr - struct representing HyperBus controller
+ * @dev: pointer to HyperBus controller device
+ * @calibrated: flag to indicate ctlr calibration sequence is complete
+ * @ops: HyperBus controller ops
+ */
+struct hyperbus_ctlr {
+	struct device *dev;
+	bool calibrated;
+
+	const struct hyperbus_ops *ops;
+};
+
+/**
+ * hyperbus_register_device - probe and register a HyperBus slave memory device
+ * @hbdev: hyperbus_device struct with dev, np and ctlr field populated
+ *
+ * Return: 0 for success, others for failure.
+ */
+int hyperbus_register_device(struct hyperbus_device *hbdev);
+
+/**
+ * hyperbus_unregister_device - deregister HyperBus slave memory device
+ * @hbdev: hyperbus_device to be unregistered
+ *
+ * Return: 0 for success, others for failure.
+ */
+int hyperbus_unregister_device(struct hyperbus_device *hbdev);
+
+#endif /* __LINUX_MTD_HYPERBUS_H__ */
-- 
2.21.0

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 3/5] mtd: Add support for HyperBus memory devices
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Cypress' HyperBus is Low Signal Count, High Performance Double Data Rate
Bus interface between a host system master and one or more slave
interfaces. HyperBus is used to connect microprocessor, microcontroller,
or ASIC devices with random access NOR flash memory (called HyperFlash)
or self refresh DRAM (called HyperRAM).

Its a 8-bit data bus (DQ[7:0]) with  Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].

HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since HyperBus is x8 DDR bus,
its equivalent to x16 parallel NOR flash wrt bits per clock cycle. But
HyperBus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.

But, HyperBus memory controllers seem to abstract implementation details
and expose a simple MMIO interface to access connected flash.

Add support for registering HyperFlash devices with MTD framework. MTD
maps framework along with CFI chip support framework are used to support
communicating with flash.

Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller (HBMC) drivers calls hyperbus_register_device() to
register a single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.

HyperRAM is not supported at the moment.

HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]

[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
    Table 12-5741. HyperFlash Access Sequence

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6:
Clarify read16()/write16() APIs
Move calibration code out into TI specific driver

 MAINTAINERS                          |   7 ++
 drivers/mtd/Kconfig                  |   2 +
 drivers/mtd/Makefile                 |   1 +
 drivers/mtd/hyperbus/Kconfig         |  11 ++
 drivers/mtd/hyperbus/Makefile        |   3 +
 drivers/mtd/hyperbus/hyperbus-core.c | 154 +++++++++++++++++++++++++++
 include/linux/mtd/hyperbus.h         |  86 +++++++++++++++
 7 files changed, 264 insertions(+)
 create mode 100644 drivers/mtd/hyperbus/Kconfig
 create mode 100644 drivers/mtd/hyperbus/Makefile
 create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c
 create mode 100644 include/linux/mtd/hyperbus.h

diff --git a/MAINTAINERS b/MAINTAINERS
index ff7c2b7e67b9..58c6ad3dae66 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7353,6 +7353,13 @@ F:	include/asm-generic/mshyperv.h
 F:	tools/hv/
 F:	Documentation/ABI/stable/sysfs-bus-vmbus
 
+HYPERBUS SUPPORT
+M:	Vignesh Raghavendra <vigneshr@ti.com>
+S:	Supported
+F:	drivers/mtd/hyperbus/
+F:	include/linux/mtd/hyperbus.h
+F:	Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
+
 HYPERVISOR VIRTUAL CONSOLE DRIVER
 L:	linuxppc-dev@lists.ozlabs.org
 S:	Odd Fixes
diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig
index fb31a7f649a3..80a6e2dcd085 100644
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -274,4 +274,6 @@ source "drivers/mtd/spi-nor/Kconfig"
 
 source "drivers/mtd/ubi/Kconfig"
 
+source "drivers/mtd/hyperbus/Kconfig"
+
 endif # MTD
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index 806287e80e84..62d649a959e2 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -34,3 +34,4 @@ obj-y		+= chips/ lpddr/ maps/ devices/ nand/ tests/
 
 obj-$(CONFIG_MTD_SPI_NOR)	+= spi-nor/
 obj-$(CONFIG_MTD_UBI)		+= ubi/
+obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus/
diff --git a/drivers/mtd/hyperbus/Kconfig b/drivers/mtd/hyperbus/Kconfig
new file mode 100644
index 000000000000..98147e28caa0
--- /dev/null
+++ b/drivers/mtd/hyperbus/Kconfig
@@ -0,0 +1,11 @@
+menuconfig MTD_HYPERBUS
+	tristate "HyperBus support"
+	select MTD_CFI
+	select MTD_MAP_BANK_WIDTH_2
+	select MTD_CFI_AMDSTD
+	select MTD_COMPLEX_MAPPINGS
+	help
+	  This is the framework for the HyperBus which can be used by
+	  the HyperBus Controller driver to communicate with
+	  HyperFlash. See Cypress HyperBus specification for more
+	  details
diff --git a/drivers/mtd/hyperbus/Makefile b/drivers/mtd/hyperbus/Makefile
new file mode 100644
index 000000000000..ca61dedd730d
--- /dev/null
+++ b/drivers/mtd/hyperbus/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus-core.o
diff --git a/drivers/mtd/hyperbus/hyperbus-core.c b/drivers/mtd/hyperbus/hyperbus-core.c
new file mode 100644
index 000000000000..63a9e64895bc
--- /dev/null
+++ b/drivers/mtd/hyperbus/hyperbus-core.c
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Author: Vignesh Raghavendra <vigneshr@ti.com>
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/hyperbus.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/mtd.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/types.h>
+
+static struct hyperbus_device *map_to_hbdev(struct map_info *map)
+{
+	return container_of(map, struct hyperbus_device, map);
+}
+
+static map_word hyperbus_read16(struct map_info *map, unsigned long addr)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+	map_word read_data;
+
+	read_data.x[0] = ctlr->ops->read16(hbdev, addr);
+
+	return read_data;
+}
+
+static void hyperbus_write16(struct map_info *map, map_word d,
+			     unsigned long addr)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->write16(hbdev, addr, d.x[0]);
+}
+
+static void hyperbus_copy_from(struct map_info *map, void *to,
+			       unsigned long from, ssize_t len)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->copy_from(hbdev, to, from, len);
+}
+
+static void hyperbus_copy_to(struct map_info *map, unsigned long to,
+			     const void *from, ssize_t len)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->copy_to(hbdev, to, from, len);
+}
+
+int hyperbus_register_device(struct hyperbus_device *hbdev)
+{
+	const struct hyperbus_ops *ops;
+	struct hyperbus_ctlr *ctlr;
+	struct device_node *np;
+	struct map_info *map;
+	struct resource res;
+	struct device *dev;
+	int ret;
+
+	if (!hbdev || !hbdev->np || !hbdev->ctlr || !hbdev->ctlr->dev) {
+		pr_err("hyperbus: please fill all the necessary fields!\n");
+		return -EINVAL;
+	}
+
+	np = hbdev->np;
+	ctlr = hbdev->ctlr;
+	if (!of_device_is_compatible(np, "cypress,hyperflash"))
+		return -ENODEV;
+
+	hbdev->memtype = HYPERFLASH;
+
+	ret = of_address_to_resource(np, 0, &res);
+	if (ret)
+		return ret;
+
+	dev = ctlr->dev;
+	map = &hbdev->map;
+	map->size = resource_size(&res);
+	map->virt = devm_ioremap_resource(dev, &res);
+	if (IS_ERR(map->virt))
+		return PTR_ERR(map->virt);
+
+	map->name = dev_name(dev);
+	map->bankwidth = 2;
+	map->device_node = np;
+
+	simple_map_init(map);
+	ops = ctlr->ops;
+	if (ops) {
+		if (ops->read16)
+			map->read = hyperbus_read16;
+		if (ops->write16)
+			map->write = hyperbus_write16;
+		if (ops->copy_to)
+			map->copy_to = hyperbus_copy_to;
+		if (ops->copy_from)
+			map->copy_from = hyperbus_copy_from;
+
+		if (ops->calibrate && !ctlr->calibrated) {
+			ret = ops->calibrate(hbdev);
+			if (!ret) {
+				dev_err(dev, "Calibration failed\n");
+				return -ENODEV;
+			}
+			ctlr->calibrated = true;
+		}
+	}
+
+	hbdev->mtd = do_map_probe("cfi_probe", map);
+	if (!hbdev->mtd) {
+		dev_err(dev, "probing of hyperbus device failed\n");
+		return -ENODEV;
+	}
+
+	hbdev->mtd->dev.parent = dev;
+	mtd_set_of_node(hbdev->mtd, np);
+
+	ret = mtd_device_register(hbdev->mtd, NULL, 0);
+	if (ret) {
+		dev_err(dev, "failed to register mtd device\n");
+		map_destroy(hbdev->mtd);
+		return ret;
+	}
+	hbdev->registered = true;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(hyperbus_register_device);
+
+int hyperbus_unregister_device(struct hyperbus_device *hbdev)
+{
+	int ret = 0;
+
+	if (hbdev && hbdev->mtd && hbdev->registered) {
+		ret = mtd_device_unregister(hbdev->mtd);
+		map_destroy(hbdev->mtd);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(hyperbus_unregister_device);
+
+MODULE_DESCRIPTION("HyperBus Framework");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>");
diff --git a/include/linux/mtd/hyperbus.h b/include/linux/mtd/hyperbus.h
new file mode 100644
index 000000000000..ead969aad35b
--- /dev/null
+++ b/include/linux/mtd/hyperbus.h
@@ -0,0 +1,86 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#ifndef __LINUX_MTD_HYPERBUS_H__
+#define __LINUX_MTD_HYPERBUS_H__
+
+#include <linux/mtd/map.h>
+
+enum hyperbus_memtype {
+	HYPERFLASH,
+	HYPERRAM,
+};
+
+/**
+ * struct hyperbus_device - struct representing HyperBus slave device
+ * @map: map_info struct for accessing MMIO HyperBus flash memory
+ * @np: pointer to HyperBus slave device node
+ * @mtd: pointer to MTD struct
+ * @ctlr: pointer to HyperBus controller struct
+ * @memtype: type of memory device: HyperFlash or HyperRAM
+ * @registered: flag to indicate whether device is registered with MTD core
+ */
+
+struct hyperbus_device {
+	struct map_info map;
+	struct device_node *np;
+	struct mtd_info *mtd;
+	struct hyperbus_ctlr *ctlr;
+	enum hyperbus_memtype memtype;
+	bool registered;
+};
+
+/**
+ * struct hyperbus_ops - struct representing custom HyperBus operations
+ * @read16: read 16 bit of data to flash in a single burst. Used to read
+ *          from non default address space, such as ID/CFI space
+ * @write16: write 16 bit of data to flash in a single burst. Used to
+ *           send cmd to flash or write single 16 bit word at a time
+ * @copy_from: copy data from flash memory
+ * @copy_to: copy data to flash memory
+ * @calibrate: calibrate HyperBus controller
+ */
+
+struct hyperbus_ops {
+	u16 (*read16)(struct hyperbus_device *hbdev, unsigned long addr);
+	void (*write16)(struct hyperbus_device *hbdev,
+			unsigned long addr, u16 val);
+	void (*copy_from)(struct hyperbus_device *hbdev, void *to,
+			  unsigned long from, ssize_t len);
+	void (*copy_to)(struct hyperbus_device *dev, unsigned long to,
+			const void *from, ssize_t len);
+	int (*calibrate)(struct hyperbus_device *dev);
+};
+
+/**
+ * struct hyperbus_ctlr - struct representing HyperBus controller
+ * @dev: pointer to HyperBus controller device
+ * @calibrated: flag to indicate ctlr calibration sequence is complete
+ * @ops: HyperBus controller ops
+ */
+struct hyperbus_ctlr {
+	struct device *dev;
+	bool calibrated;
+
+	const struct hyperbus_ops *ops;
+};
+
+/**
+ * hyperbus_register_device - probe and register a HyperBus slave memory device
+ * @hbdev: hyperbus_device struct with dev, np and ctlr field populated
+ *
+ * Return: 0 for success, others for failure.
+ */
+int hyperbus_register_device(struct hyperbus_device *hbdev);
+
+/**
+ * hyperbus_unregister_device - deregister HyperBus slave memory device
+ * @hbdev: hyperbus_device to be unregistered
+ *
+ * Return: 0 for success, others for failure.
+ */
+int hyperbus_unregister_device(struct hyperbus_device *hbdev);
+
+#endif /* __LINUX_MTD_HYPERBUS_H__ */
-- 
2.21.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 3/5] mtd: Add support for HyperBus memory devices
@ 2019-06-18  9:28   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:28 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Cypress' HyperBus is Low Signal Count, High Performance Double Data Rate
Bus interface between a host system master and one or more slave
interfaces. HyperBus is used to connect microprocessor, microcontroller,
or ASIC devices with random access NOR flash memory (called HyperFlash)
or self refresh DRAM (called HyperRAM).

Its a 8-bit data bus (DQ[7:0]) with  Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].

HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since HyperBus is x8 DDR bus,
its equivalent to x16 parallel NOR flash wrt bits per clock cycle. But
HyperBus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.

But, HyperBus memory controllers seem to abstract implementation details
and expose a simple MMIO interface to access connected flash.

Add support for registering HyperFlash devices with MTD framework. MTD
maps framework along with CFI chip support framework are used to support
communicating with flash.

Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller (HBMC) drivers calls hyperbus_register_device() to
register a single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.

HyperRAM is not supported at the moment.

HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]

[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
    Table 12-5741. HyperFlash Access Sequence

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6:
Clarify read16()/write16() APIs
Move calibration code out into TI specific driver

 MAINTAINERS                          |   7 ++
 drivers/mtd/Kconfig                  |   2 +
 drivers/mtd/Makefile                 |   1 +
 drivers/mtd/hyperbus/Kconfig         |  11 ++
 drivers/mtd/hyperbus/Makefile        |   3 +
 drivers/mtd/hyperbus/hyperbus-core.c | 154 +++++++++++++++++++++++++++
 include/linux/mtd/hyperbus.h         |  86 +++++++++++++++
 7 files changed, 264 insertions(+)
 create mode 100644 drivers/mtd/hyperbus/Kconfig
 create mode 100644 drivers/mtd/hyperbus/Makefile
 create mode 100644 drivers/mtd/hyperbus/hyperbus-core.c
 create mode 100644 include/linux/mtd/hyperbus.h

diff --git a/MAINTAINERS b/MAINTAINERS
index ff7c2b7e67b9..58c6ad3dae66 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7353,6 +7353,13 @@ F:	include/asm-generic/mshyperv.h
 F:	tools/hv/
 F:	Documentation/ABI/stable/sysfs-bus-vmbus
 
+HYPERBUS SUPPORT
+M:	Vignesh Raghavendra <vigneshr@ti.com>
+S:	Supported
+F:	drivers/mtd/hyperbus/
+F:	include/linux/mtd/hyperbus.h
+F:	Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
+
 HYPERVISOR VIRTUAL CONSOLE DRIVER
 L:	linuxppc-dev@lists.ozlabs.org
 S:	Odd Fixes
diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig
index fb31a7f649a3..80a6e2dcd085 100644
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -274,4 +274,6 @@ source "drivers/mtd/spi-nor/Kconfig"
 
 source "drivers/mtd/ubi/Kconfig"
 
+source "drivers/mtd/hyperbus/Kconfig"
+
 endif # MTD
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index 806287e80e84..62d649a959e2 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -34,3 +34,4 @@ obj-y		+= chips/ lpddr/ maps/ devices/ nand/ tests/
 
 obj-$(CONFIG_MTD_SPI_NOR)	+= spi-nor/
 obj-$(CONFIG_MTD_UBI)		+= ubi/
+obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus/
diff --git a/drivers/mtd/hyperbus/Kconfig b/drivers/mtd/hyperbus/Kconfig
new file mode 100644
index 000000000000..98147e28caa0
--- /dev/null
+++ b/drivers/mtd/hyperbus/Kconfig
@@ -0,0 +1,11 @@
+menuconfig MTD_HYPERBUS
+	tristate "HyperBus support"
+	select MTD_CFI
+	select MTD_MAP_BANK_WIDTH_2
+	select MTD_CFI_AMDSTD
+	select MTD_COMPLEX_MAPPINGS
+	help
+	  This is the framework for the HyperBus which can be used by
+	  the HyperBus Controller driver to communicate with
+	  HyperFlash. See Cypress HyperBus specification for more
+	  details
diff --git a/drivers/mtd/hyperbus/Makefile b/drivers/mtd/hyperbus/Makefile
new file mode 100644
index 000000000000..ca61dedd730d
--- /dev/null
+++ b/drivers/mtd/hyperbus/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus-core.o
diff --git a/drivers/mtd/hyperbus/hyperbus-core.c b/drivers/mtd/hyperbus/hyperbus-core.c
new file mode 100644
index 000000000000..63a9e64895bc
--- /dev/null
+++ b/drivers/mtd/hyperbus/hyperbus-core.c
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Author: Vignesh Raghavendra <vigneshr@ti.com>
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/hyperbus.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/mtd.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/types.h>
+
+static struct hyperbus_device *map_to_hbdev(struct map_info *map)
+{
+	return container_of(map, struct hyperbus_device, map);
+}
+
+static map_word hyperbus_read16(struct map_info *map, unsigned long addr)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+	map_word read_data;
+
+	read_data.x[0] = ctlr->ops->read16(hbdev, addr);
+
+	return read_data;
+}
+
+static void hyperbus_write16(struct map_info *map, map_word d,
+			     unsigned long addr)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->write16(hbdev, addr, d.x[0]);
+}
+
+static void hyperbus_copy_from(struct map_info *map, void *to,
+			       unsigned long from, ssize_t len)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->copy_from(hbdev, to, from, len);
+}
+
+static void hyperbus_copy_to(struct map_info *map, unsigned long to,
+			     const void *from, ssize_t len)
+{
+	struct hyperbus_device *hbdev = map_to_hbdev(map);
+	struct hyperbus_ctlr *ctlr = hbdev->ctlr;
+
+	ctlr->ops->copy_to(hbdev, to, from, len);
+}
+
+int hyperbus_register_device(struct hyperbus_device *hbdev)
+{
+	const struct hyperbus_ops *ops;
+	struct hyperbus_ctlr *ctlr;
+	struct device_node *np;
+	struct map_info *map;
+	struct resource res;
+	struct device *dev;
+	int ret;
+
+	if (!hbdev || !hbdev->np || !hbdev->ctlr || !hbdev->ctlr->dev) {
+		pr_err("hyperbus: please fill all the necessary fields!\n");
+		return -EINVAL;
+	}
+
+	np = hbdev->np;
+	ctlr = hbdev->ctlr;
+	if (!of_device_is_compatible(np, "cypress,hyperflash"))
+		return -ENODEV;
+
+	hbdev->memtype = HYPERFLASH;
+
+	ret = of_address_to_resource(np, 0, &res);
+	if (ret)
+		return ret;
+
+	dev = ctlr->dev;
+	map = &hbdev->map;
+	map->size = resource_size(&res);
+	map->virt = devm_ioremap_resource(dev, &res);
+	if (IS_ERR(map->virt))
+		return PTR_ERR(map->virt);
+
+	map->name = dev_name(dev);
+	map->bankwidth = 2;
+	map->device_node = np;
+
+	simple_map_init(map);
+	ops = ctlr->ops;
+	if (ops) {
+		if (ops->read16)
+			map->read = hyperbus_read16;
+		if (ops->write16)
+			map->write = hyperbus_write16;
+		if (ops->copy_to)
+			map->copy_to = hyperbus_copy_to;
+		if (ops->copy_from)
+			map->copy_from = hyperbus_copy_from;
+
+		if (ops->calibrate && !ctlr->calibrated) {
+			ret = ops->calibrate(hbdev);
+			if (!ret) {
+				dev_err(dev, "Calibration failed\n");
+				return -ENODEV;
+			}
+			ctlr->calibrated = true;
+		}
+	}
+
+	hbdev->mtd = do_map_probe("cfi_probe", map);
+	if (!hbdev->mtd) {
+		dev_err(dev, "probing of hyperbus device failed\n");
+		return -ENODEV;
+	}
+
+	hbdev->mtd->dev.parent = dev;
+	mtd_set_of_node(hbdev->mtd, np);
+
+	ret = mtd_device_register(hbdev->mtd, NULL, 0);
+	if (ret) {
+		dev_err(dev, "failed to register mtd device\n");
+		map_destroy(hbdev->mtd);
+		return ret;
+	}
+	hbdev->registered = true;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(hyperbus_register_device);
+
+int hyperbus_unregister_device(struct hyperbus_device *hbdev)
+{
+	int ret = 0;
+
+	if (hbdev && hbdev->mtd && hbdev->registered) {
+		ret = mtd_device_unregister(hbdev->mtd);
+		map_destroy(hbdev->mtd);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(hyperbus_unregister_device);
+
+MODULE_DESCRIPTION("HyperBus Framework");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>");
diff --git a/include/linux/mtd/hyperbus.h b/include/linux/mtd/hyperbus.h
new file mode 100644
index 000000000000..ead969aad35b
--- /dev/null
+++ b/include/linux/mtd/hyperbus.h
@@ -0,0 +1,86 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#ifndef __LINUX_MTD_HYPERBUS_H__
+#define __LINUX_MTD_HYPERBUS_H__
+
+#include <linux/mtd/map.h>
+
+enum hyperbus_memtype {
+	HYPERFLASH,
+	HYPERRAM,
+};
+
+/**
+ * struct hyperbus_device - struct representing HyperBus slave device
+ * @map: map_info struct for accessing MMIO HyperBus flash memory
+ * @np: pointer to HyperBus slave device node
+ * @mtd: pointer to MTD struct
+ * @ctlr: pointer to HyperBus controller struct
+ * @memtype: type of memory device: HyperFlash or HyperRAM
+ * @registered: flag to indicate whether device is registered with MTD core
+ */
+
+struct hyperbus_device {
+	struct map_info map;
+	struct device_node *np;
+	struct mtd_info *mtd;
+	struct hyperbus_ctlr *ctlr;
+	enum hyperbus_memtype memtype;
+	bool registered;
+};
+
+/**
+ * struct hyperbus_ops - struct representing custom HyperBus operations
+ * @read16: read 16 bit of data to flash in a single burst. Used to read
+ *          from non default address space, such as ID/CFI space
+ * @write16: write 16 bit of data to flash in a single burst. Used to
+ *           send cmd to flash or write single 16 bit word at a time
+ * @copy_from: copy data from flash memory
+ * @copy_to: copy data to flash memory
+ * @calibrate: calibrate HyperBus controller
+ */
+
+struct hyperbus_ops {
+	u16 (*read16)(struct hyperbus_device *hbdev, unsigned long addr);
+	void (*write16)(struct hyperbus_device *hbdev,
+			unsigned long addr, u16 val);
+	void (*copy_from)(struct hyperbus_device *hbdev, void *to,
+			  unsigned long from, ssize_t len);
+	void (*copy_to)(struct hyperbus_device *dev, unsigned long to,
+			const void *from, ssize_t len);
+	int (*calibrate)(struct hyperbus_device *dev);
+};
+
+/**
+ * struct hyperbus_ctlr - struct representing HyperBus controller
+ * @dev: pointer to HyperBus controller device
+ * @calibrated: flag to indicate ctlr calibration sequence is complete
+ * @ops: HyperBus controller ops
+ */
+struct hyperbus_ctlr {
+	struct device *dev;
+	bool calibrated;
+
+	const struct hyperbus_ops *ops;
+};
+
+/**
+ * hyperbus_register_device - probe and register a HyperBus slave memory device
+ * @hbdev: hyperbus_device struct with dev, np and ctlr field populated
+ *
+ * Return: 0 for success, others for failure.
+ */
+int hyperbus_register_device(struct hyperbus_device *hbdev);
+
+/**
+ * hyperbus_unregister_device - deregister HyperBus slave memory device
+ * @hbdev: hyperbus_device to be unregistered
+ *
+ * Return: 0 for success, others for failure.
+ */
+int hyperbus_unregister_device(struct hyperbus_device *hbdev);
+
+#endif /* __LINUX_MTD_HYPERBUS_H__ */
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 4/5] dt-bindings: mtd: Add bindings for TI's AM654 HyperBus memory controller
  2019-06-18  9:28 ` Vignesh Raghavendra
  (?)
  (?)
@ 2019-06-18  9:29   ` Vignesh Raghavendra
  -1 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:29 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

Add binding documentation for TI's HyperBus memory controller present on
AM654 SoC.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6:
Use generic names for bindings

 .../devicetree/bindings/mtd/ti,am654-hbmc.txt | 51 +++++++++++++++++++
 MAINTAINERS                                   |  1 +
 2 files changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt

diff --git a/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
new file mode 100644
index 000000000000..c06038c136d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
@@ -0,0 +1,51 @@
+Bindings for HyperBus Memory Controller (HBMC) on TI's K3 family of SoCs
+
+Required properties:
+- compatible : "ti,am654-hbmc" for AM654 SoC
+- reg : Two entries:
+	First entry pointed to the register space of HBMC controller
+	Second entry pointing to the memory map region dedicated for
+	MMIO access to attached flash devices
+- ranges : Address translation from offset within CS to allocated MMIO
+	   space in SoC
+
+Optional properties:
+- mux-controls : phandle to the multiplexer that controls selection of
+		 HBMC vs OSPI inside Flash SubSystem (FSS). Default is OSPI,
+		 if property is absent.
+		 See Documentation/devicetree/bindings/mux/reg-mux.txt
+		 for mmio-mux binding details
+
+Example:
+
+	fss: system-controller@47000000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x47000000 0x0 0x100>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hbmc_mux: multiplexer {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4 0x2>; /* 0: reg 0x4, bit 1 */
+		};
+
+		hbmc: hyperbus@47034000 {
+			compatible = "ti,am654-hbmc";
+			reg = <0x0 0x47034000 0x0 0x100>,
+				<0x5 0x00000000 0x1 0x0000000>;
+			power-domains = <&k3_pds 55>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x5 0x00000000 0x4000000>, /* CS0 - 64MB */
+				 <0x1 0x0 0x5 0x04000000 0x4000000>; /* CS1 - 64MB */
+			mux-controls = <&hbmc_mux 0>;
+
+			/* Slave flash node */
+			flash@0,0 {
+				compatible = "cypress,hyperflash", "cfi-flash";
+				reg = <0x0 0x0 0x4000000>;
+			};
+		};
+	};
diff --git a/MAINTAINERS b/MAINTAINERS
index 58c6ad3dae66..0d5a8c36682d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7359,6 +7359,7 @@ S:	Supported
 F:	drivers/mtd/hyperbus/
 F:	include/linux/mtd/hyperbus.h
 F:	Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
+F:	Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
 
 HYPERVISOR VIRTUAL CONSOLE DRIVER
 L:	linuxppc-dev@lists.ozlabs.org
-- 
2.21.0


^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 4/5] dt-bindings: mtd: Add bindings for TI's AM654 HyperBus memory controller
@ 2019-06-18  9:29   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:29 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

Add binding documentation for TI's HyperBus memory controller present on
AM654 SoC.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6:
Use generic names for bindings

 .../devicetree/bindings/mtd/ti,am654-hbmc.txt | 51 +++++++++++++++++++
 MAINTAINERS                                   |  1 +
 2 files changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt

diff --git a/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
new file mode 100644
index 000000000000..c06038c136d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
@@ -0,0 +1,51 @@
+Bindings for HyperBus Memory Controller (HBMC) on TI's K3 family of SoCs
+
+Required properties:
+- compatible : "ti,am654-hbmc" for AM654 SoC
+- reg : Two entries:
+	First entry pointed to the register space of HBMC controller
+	Second entry pointing to the memory map region dedicated for
+	MMIO access to attached flash devices
+- ranges : Address translation from offset within CS to allocated MMIO
+	   space in SoC
+
+Optional properties:
+- mux-controls : phandle to the multiplexer that controls selection of
+		 HBMC vs OSPI inside Flash SubSystem (FSS). Default is OSPI,
+		 if property is absent.
+		 See Documentation/devicetree/bindings/mux/reg-mux.txt
+		 for mmio-mux binding details
+
+Example:
+
+	fss: system-controller@47000000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x47000000 0x0 0x100>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hbmc_mux: multiplexer {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4 0x2>; /* 0: reg 0x4, bit 1 */
+		};
+
+		hbmc: hyperbus@47034000 {
+			compatible = "ti,am654-hbmc";
+			reg = <0x0 0x47034000 0x0 0x100>,
+				<0x5 0x00000000 0x1 0x0000000>;
+			power-domains = <&k3_pds 55>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x5 0x00000000 0x4000000>, /* CS0 - 64MB */
+				 <0x1 0x0 0x5 0x04000000 0x4000000>; /* CS1 - 64MB */
+			mux-controls = <&hbmc_mux 0>;
+
+			/* Slave flash node */
+			flash@0,0 {
+				compatible = "cypress,hyperflash", "cfi-flash";
+				reg = <0x0 0x0 0x4000000>;
+			};
+		};
+	};
diff --git a/MAINTAINERS b/MAINTAINERS
index 58c6ad3dae66..0d5a8c36682d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7359,6 +7359,7 @@ S:	Supported
 F:	drivers/mtd/hyperbus/
 F:	include/linux/mtd/hyperbus.h
 F:	Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
+F:	Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
 
 HYPERVISOR VIRTUAL CONSOLE DRIVER
 L:	linuxppc-dev@lists.ozlabs.org
-- 
2.21.0

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 4/5] dt-bindings: mtd: Add bindings for TI's AM654 HyperBus memory controller
@ 2019-06-18  9:29   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:29 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Add binding documentation for TI's HyperBus memory controller present on
AM654 SoC.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6:
Use generic names for bindings

 .../devicetree/bindings/mtd/ti,am654-hbmc.txt | 51 +++++++++++++++++++
 MAINTAINERS                                   |  1 +
 2 files changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt

diff --git a/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
new file mode 100644
index 000000000000..c06038c136d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
@@ -0,0 +1,51 @@
+Bindings for HyperBus Memory Controller (HBMC) on TI's K3 family of SoCs
+
+Required properties:
+- compatible : "ti,am654-hbmc" for AM654 SoC
+- reg : Two entries:
+	First entry pointed to the register space of HBMC controller
+	Second entry pointing to the memory map region dedicated for
+	MMIO access to attached flash devices
+- ranges : Address translation from offset within CS to allocated MMIO
+	   space in SoC
+
+Optional properties:
+- mux-controls : phandle to the multiplexer that controls selection of
+		 HBMC vs OSPI inside Flash SubSystem (FSS). Default is OSPI,
+		 if property is absent.
+		 See Documentation/devicetree/bindings/mux/reg-mux.txt
+		 for mmio-mux binding details
+
+Example:
+
+	fss: system-controller@47000000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x47000000 0x0 0x100>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hbmc_mux: multiplexer {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4 0x2>; /* 0: reg 0x4, bit 1 */
+		};
+
+		hbmc: hyperbus@47034000 {
+			compatible = "ti,am654-hbmc";
+			reg = <0x0 0x47034000 0x0 0x100>,
+				<0x5 0x00000000 0x1 0x0000000>;
+			power-domains = <&k3_pds 55>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x5 0x00000000 0x4000000>, /* CS0 - 64MB */
+				 <0x1 0x0 0x5 0x04000000 0x4000000>; /* CS1 - 64MB */
+			mux-controls = <&hbmc_mux 0>;
+
+			/* Slave flash node */
+			flash@0,0 {
+				compatible = "cypress,hyperflash", "cfi-flash";
+				reg = <0x0 0x0 0x4000000>;
+			};
+		};
+	};
diff --git a/MAINTAINERS b/MAINTAINERS
index 58c6ad3dae66..0d5a8c36682d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7359,6 +7359,7 @@ S:	Supported
 F:	drivers/mtd/hyperbus/
 F:	include/linux/mtd/hyperbus.h
 F:	Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
+F:	Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
 
 HYPERVISOR VIRTUAL CONSOLE DRIVER
 L:	linuxppc-dev@lists.ozlabs.org
-- 
2.21.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 4/5] dt-bindings: mtd: Add bindings for TI's AM654 HyperBus memory controller
@ 2019-06-18  9:29   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:29 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Add binding documentation for TI's HyperBus memory controller present on
AM654 SoC.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6:
Use generic names for bindings

 .../devicetree/bindings/mtd/ti,am654-hbmc.txt | 51 +++++++++++++++++++
 MAINTAINERS                                   |  1 +
 2 files changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt

diff --git a/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
new file mode 100644
index 000000000000..c06038c136d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
@@ -0,0 +1,51 @@
+Bindings for HyperBus Memory Controller (HBMC) on TI's K3 family of SoCs
+
+Required properties:
+- compatible : "ti,am654-hbmc" for AM654 SoC
+- reg : Two entries:
+	First entry pointed to the register space of HBMC controller
+	Second entry pointing to the memory map region dedicated for
+	MMIO access to attached flash devices
+- ranges : Address translation from offset within CS to allocated MMIO
+	   space in SoC
+
+Optional properties:
+- mux-controls : phandle to the multiplexer that controls selection of
+		 HBMC vs OSPI inside Flash SubSystem (FSS). Default is OSPI,
+		 if property is absent.
+		 See Documentation/devicetree/bindings/mux/reg-mux.txt
+		 for mmio-mux binding details
+
+Example:
+
+	fss: system-controller@47000000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x47000000 0x0 0x100>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hbmc_mux: multiplexer {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4 0x2>; /* 0: reg 0x4, bit 1 */
+		};
+
+		hbmc: hyperbus@47034000 {
+			compatible = "ti,am654-hbmc";
+			reg = <0x0 0x47034000 0x0 0x100>,
+				<0x5 0x00000000 0x1 0x0000000>;
+			power-domains = <&k3_pds 55>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x5 0x00000000 0x4000000>, /* CS0 - 64MB */
+				 <0x1 0x0 0x5 0x04000000 0x4000000>; /* CS1 - 64MB */
+			mux-controls = <&hbmc_mux 0>;
+
+			/* Slave flash node */
+			flash@0,0 {
+				compatible = "cypress,hyperflash", "cfi-flash";
+				reg = <0x0 0x0 0x4000000>;
+			};
+		};
+	};
diff --git a/MAINTAINERS b/MAINTAINERS
index 58c6ad3dae66..0d5a8c36682d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7359,6 +7359,7 @@ S:	Supported
 F:	drivers/mtd/hyperbus/
 F:	include/linux/mtd/hyperbus.h
 F:	Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt
+F:	Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt
 
 HYPERVISOR VIRTUAL CONSOLE DRIVER
 L:	linuxppc-dev@lists.ozlabs.org
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 5/5] mtd: hyperbus: Add driver for TI's HyperBus memory controller
  2019-06-18  9:28 ` Vignesh Raghavendra
  (?)
  (?)
@ 2019-06-18  9:29   ` Vignesh Raghavendra
  -1 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:29 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

Add driver for HyperBus memory controller on TI's AM654 SoC. Programming
IP is pretty simple and provides direct memory mapped access to
connected Flash devices.

Add basic support for the IP without DMA. Second chipSelect is not
supported for now.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6: Move calibration routine here from core.

 drivers/mtd/hyperbus/Kconfig      |  12 +++
 drivers/mtd/hyperbus/Makefile     |   1 +
 drivers/mtd/hyperbus/hbmc-am654.c | 141 ++++++++++++++++++++++++++++++
 3 files changed, 154 insertions(+)
 create mode 100644 drivers/mtd/hyperbus/hbmc-am654.c

diff --git a/drivers/mtd/hyperbus/Kconfig b/drivers/mtd/hyperbus/Kconfig
index 98147e28caa0..cff6bbd226f5 100644
--- a/drivers/mtd/hyperbus/Kconfig
+++ b/drivers/mtd/hyperbus/Kconfig
@@ -9,3 +9,15 @@ menuconfig MTD_HYPERBUS
 	  the HyperBus Controller driver to communicate with
 	  HyperFlash. See Cypress HyperBus specification for more
 	  details
+
+if MTD_HYPERBUS
+
+config HBMC_AM654
+	tristate "HyperBus controller driver for AM65x SoC"
+	select MULTIPLEXER
+	select MUX_MMIO
+	help
+	 This is the driver for HyperBus controller on TI's AM65x and
+	 other SoCs
+
+endif # MTD_HYPERBUS
diff --git a/drivers/mtd/hyperbus/Makefile b/drivers/mtd/hyperbus/Makefile
index ca61dedd730d..8a936e066f48 100644
--- a/drivers/mtd/hyperbus/Makefile
+++ b/drivers/mtd/hyperbus/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0
 
 obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus-core.o
+obj-$(CONFIG_HBMC_AM654)	+= hbmc-am654.o
diff --git a/drivers/mtd/hyperbus/hbmc-am654.c b/drivers/mtd/hyperbus/hbmc-am654.c
new file mode 100644
index 000000000000..ca3fe198169e
--- /dev/null
+++ b/drivers/mtd/hyperbus/hbmc-am654.c
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Author: Vignesh Raghavendra <vigneshr@ti.com>
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/hyperbus.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mux/consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/types.h>
+
+#define AM654_HBMC_CALIB_COUNT 25
+
+struct am654_hbmc_priv {
+	struct hyperbus_ctlr ctlr;
+	struct hyperbus_device hbdev;
+};
+
+static int am654_hbmc_calibrate(struct hyperbus_device *hbdev)
+{
+	struct map_info *map = &hbdev->map;
+	struct cfi_private cfi;
+	int count = AM654_HBMC_CALIB_COUNT;
+	int pass_count = 0;
+	int ret;
+
+	cfi.interleave = 1;
+	cfi.device_type = CFI_DEVICETYPE_X16;
+	cfi_send_gen_cmd(0xF0, 0, 0, map, &cfi, cfi.device_type, NULL);
+	cfi_send_gen_cmd(0x98, 0x55, 0, map, &cfi, cfi.device_type, NULL);
+
+	while (count--) {
+		ret = cfi_qry_present(map, 0, &cfi);
+		if (ret)
+			pass_count++;
+		else
+			pass_count = 0;
+		if (pass_count == 5)
+			break;
+	}
+
+	cfi_qry_mode_off(0, map, &cfi);
+
+	return ret;
+}
+
+static const struct hyperbus_ops am654_hbmc_ops = {
+	.calibrate = am654_hbmc_calibrate,
+};
+
+static int am654_hbmc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct am654_hbmc_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, priv);
+
+	if (of_property_read_bool(dev->of_node, "mux-controls")) {
+		struct mux_control *control = devm_mux_control_get(dev, NULL);
+
+		if (IS_ERR(control))
+			return PTR_ERR(control);
+
+		ret = mux_control_select(control, 1);
+		if (ret) {
+			dev_err(dev, "Failed to select HBMC mux\n");
+			return ret;
+		}
+	}
+
+	pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(dev);
+		goto disable_pm;
+	}
+
+	priv->ctlr.dev = dev;
+	priv->ctlr.ops = &am654_hbmc_ops;
+	priv->hbdev.ctlr = &priv->ctlr;
+	priv->hbdev.np = of_get_next_child(dev->of_node, NULL);
+	ret = hyperbus_register_device(&priv->hbdev);
+	if (ret) {
+		dev_err(dev, "failed to register controller\n");
+		pm_runtime_put_sync(&pdev->dev);
+		goto disable_pm;
+	}
+
+	return 0;
+disable_pm:
+	pm_runtime_disable(dev);
+	return ret;
+}
+
+static int am654_hbmc_remove(struct platform_device *pdev)
+{
+	struct am654_hbmc_priv *priv = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = hyperbus_unregister_device(&priv->hbdev);
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+
+	return ret;
+}
+
+static const struct of_device_id am654_hbmc_dt_ids[] = {
+	{
+		.compatible = "ti,am654-hbmc",
+	},
+	{ /* end of table */ }
+};
+
+MODULE_DEVICE_TABLE(of, am654_hbmc_dt_ids);
+
+static struct platform_driver am654_hbmc_platform_driver = {
+	.probe = am654_hbmc_probe,
+	.remove = am654_hbmc_remove,
+	.driver = {
+		.name = "hbmc-am654",
+		.of_match_table = am654_hbmc_dt_ids,
+	},
+};
+
+module_platform_driver(am654_hbmc_platform_driver);
+
+MODULE_DESCRIPTION("HBMC driver for AM654 SoC");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hbmc-am654");
+MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>");
-- 
2.21.0


^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 5/5] mtd: hyperbus: Add driver for TI's HyperBus memory controller
@ 2019-06-18  9:29   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:29 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: linux-mtd, Tudor Ambarus, Miquel Raynal, Joakim Tjernlund,
	devicetree, Sergei Shtylyov, Mason Yang, linux-arm-kernel,
	linux-kernel

Add driver for HyperBus memory controller on TI's AM654 SoC. Programming
IP is pretty simple and provides direct memory mapped access to
connected Flash devices.

Add basic support for the IP without DMA. Second chipSelect is not
supported for now.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6: Move calibration routine here from core.

 drivers/mtd/hyperbus/Kconfig      |  12 +++
 drivers/mtd/hyperbus/Makefile     |   1 +
 drivers/mtd/hyperbus/hbmc-am654.c | 141 ++++++++++++++++++++++++++++++
 3 files changed, 154 insertions(+)
 create mode 100644 drivers/mtd/hyperbus/hbmc-am654.c

diff --git a/drivers/mtd/hyperbus/Kconfig b/drivers/mtd/hyperbus/Kconfig
index 98147e28caa0..cff6bbd226f5 100644
--- a/drivers/mtd/hyperbus/Kconfig
+++ b/drivers/mtd/hyperbus/Kconfig
@@ -9,3 +9,15 @@ menuconfig MTD_HYPERBUS
 	  the HyperBus Controller driver to communicate with
 	  HyperFlash. See Cypress HyperBus specification for more
 	  details
+
+if MTD_HYPERBUS
+
+config HBMC_AM654
+	tristate "HyperBus controller driver for AM65x SoC"
+	select MULTIPLEXER
+	select MUX_MMIO
+	help
+	 This is the driver for HyperBus controller on TI's AM65x and
+	 other SoCs
+
+endif # MTD_HYPERBUS
diff --git a/drivers/mtd/hyperbus/Makefile b/drivers/mtd/hyperbus/Makefile
index ca61dedd730d..8a936e066f48 100644
--- a/drivers/mtd/hyperbus/Makefile
+++ b/drivers/mtd/hyperbus/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0
 
 obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus-core.o
+obj-$(CONFIG_HBMC_AM654)	+= hbmc-am654.o
diff --git a/drivers/mtd/hyperbus/hbmc-am654.c b/drivers/mtd/hyperbus/hbmc-am654.c
new file mode 100644
index 000000000000..ca3fe198169e
--- /dev/null
+++ b/drivers/mtd/hyperbus/hbmc-am654.c
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Author: Vignesh Raghavendra <vigneshr@ti.com>
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/hyperbus.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mux/consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/types.h>
+
+#define AM654_HBMC_CALIB_COUNT 25
+
+struct am654_hbmc_priv {
+	struct hyperbus_ctlr ctlr;
+	struct hyperbus_device hbdev;
+};
+
+static int am654_hbmc_calibrate(struct hyperbus_device *hbdev)
+{
+	struct map_info *map = &hbdev->map;
+	struct cfi_private cfi;
+	int count = AM654_HBMC_CALIB_COUNT;
+	int pass_count = 0;
+	int ret;
+
+	cfi.interleave = 1;
+	cfi.device_type = CFI_DEVICETYPE_X16;
+	cfi_send_gen_cmd(0xF0, 0, 0, map, &cfi, cfi.device_type, NULL);
+	cfi_send_gen_cmd(0x98, 0x55, 0, map, &cfi, cfi.device_type, NULL);
+
+	while (count--) {
+		ret = cfi_qry_present(map, 0, &cfi);
+		if (ret)
+			pass_count++;
+		else
+			pass_count = 0;
+		if (pass_count == 5)
+			break;
+	}
+
+	cfi_qry_mode_off(0, map, &cfi);
+
+	return ret;
+}
+
+static const struct hyperbus_ops am654_hbmc_ops = {
+	.calibrate = am654_hbmc_calibrate,
+};
+
+static int am654_hbmc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct am654_hbmc_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, priv);
+
+	if (of_property_read_bool(dev->of_node, "mux-controls")) {
+		struct mux_control *control = devm_mux_control_get(dev, NULL);
+
+		if (IS_ERR(control))
+			return PTR_ERR(control);
+
+		ret = mux_control_select(control, 1);
+		if (ret) {
+			dev_err(dev, "Failed to select HBMC mux\n");
+			return ret;
+		}
+	}
+
+	pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(dev);
+		goto disable_pm;
+	}
+
+	priv->ctlr.dev = dev;
+	priv->ctlr.ops = &am654_hbmc_ops;
+	priv->hbdev.ctlr = &priv->ctlr;
+	priv->hbdev.np = of_get_next_child(dev->of_node, NULL);
+	ret = hyperbus_register_device(&priv->hbdev);
+	if (ret) {
+		dev_err(dev, "failed to register controller\n");
+		pm_runtime_put_sync(&pdev->dev);
+		goto disable_pm;
+	}
+
+	return 0;
+disable_pm:
+	pm_runtime_disable(dev);
+	return ret;
+}
+
+static int am654_hbmc_remove(struct platform_device *pdev)
+{
+	struct am654_hbmc_priv *priv = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = hyperbus_unregister_device(&priv->hbdev);
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+
+	return ret;
+}
+
+static const struct of_device_id am654_hbmc_dt_ids[] = {
+	{
+		.compatible = "ti,am654-hbmc",
+	},
+	{ /* end of table */ }
+};
+
+MODULE_DEVICE_TABLE(of, am654_hbmc_dt_ids);
+
+static struct platform_driver am654_hbmc_platform_driver = {
+	.probe = am654_hbmc_probe,
+	.remove = am654_hbmc_remove,
+	.driver = {
+		.name = "hbmc-am654",
+		.of_match_table = am654_hbmc_dt_ids,
+	},
+};
+
+module_platform_driver(am654_hbmc_platform_driver);
+
+MODULE_DESCRIPTION("HBMC driver for AM654 SoC");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hbmc-am654");
+MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>");
-- 
2.21.0

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 5/5] mtd: hyperbus: Add driver for TI's HyperBus memory controller
@ 2019-06-18  9:29   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:29 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Add driver for HyperBus memory controller on TI's AM654 SoC. Programming
IP is pretty simple and provides direct memory mapped access to
connected Flash devices.

Add basic support for the IP without DMA. Second chipSelect is not
supported for now.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6: Move calibration routine here from core.

 drivers/mtd/hyperbus/Kconfig      |  12 +++
 drivers/mtd/hyperbus/Makefile     |   1 +
 drivers/mtd/hyperbus/hbmc-am654.c | 141 ++++++++++++++++++++++++++++++
 3 files changed, 154 insertions(+)
 create mode 100644 drivers/mtd/hyperbus/hbmc-am654.c

diff --git a/drivers/mtd/hyperbus/Kconfig b/drivers/mtd/hyperbus/Kconfig
index 98147e28caa0..cff6bbd226f5 100644
--- a/drivers/mtd/hyperbus/Kconfig
+++ b/drivers/mtd/hyperbus/Kconfig
@@ -9,3 +9,15 @@ menuconfig MTD_HYPERBUS
 	  the HyperBus Controller driver to communicate with
 	  HyperFlash. See Cypress HyperBus specification for more
 	  details
+
+if MTD_HYPERBUS
+
+config HBMC_AM654
+	tristate "HyperBus controller driver for AM65x SoC"
+	select MULTIPLEXER
+	select MUX_MMIO
+	help
+	 This is the driver for HyperBus controller on TI's AM65x and
+	 other SoCs
+
+endif # MTD_HYPERBUS
diff --git a/drivers/mtd/hyperbus/Makefile b/drivers/mtd/hyperbus/Makefile
index ca61dedd730d..8a936e066f48 100644
--- a/drivers/mtd/hyperbus/Makefile
+++ b/drivers/mtd/hyperbus/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0
 
 obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus-core.o
+obj-$(CONFIG_HBMC_AM654)	+= hbmc-am654.o
diff --git a/drivers/mtd/hyperbus/hbmc-am654.c b/drivers/mtd/hyperbus/hbmc-am654.c
new file mode 100644
index 000000000000..ca3fe198169e
--- /dev/null
+++ b/drivers/mtd/hyperbus/hbmc-am654.c
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Author: Vignesh Raghavendra <vigneshr@ti.com>
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/hyperbus.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mux/consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/types.h>
+
+#define AM654_HBMC_CALIB_COUNT 25
+
+struct am654_hbmc_priv {
+	struct hyperbus_ctlr ctlr;
+	struct hyperbus_device hbdev;
+};
+
+static int am654_hbmc_calibrate(struct hyperbus_device *hbdev)
+{
+	struct map_info *map = &hbdev->map;
+	struct cfi_private cfi;
+	int count = AM654_HBMC_CALIB_COUNT;
+	int pass_count = 0;
+	int ret;
+
+	cfi.interleave = 1;
+	cfi.device_type = CFI_DEVICETYPE_X16;
+	cfi_send_gen_cmd(0xF0, 0, 0, map, &cfi, cfi.device_type, NULL);
+	cfi_send_gen_cmd(0x98, 0x55, 0, map, &cfi, cfi.device_type, NULL);
+
+	while (count--) {
+		ret = cfi_qry_present(map, 0, &cfi);
+		if (ret)
+			pass_count++;
+		else
+			pass_count = 0;
+		if (pass_count == 5)
+			break;
+	}
+
+	cfi_qry_mode_off(0, map, &cfi);
+
+	return ret;
+}
+
+static const struct hyperbus_ops am654_hbmc_ops = {
+	.calibrate = am654_hbmc_calibrate,
+};
+
+static int am654_hbmc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct am654_hbmc_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, priv);
+
+	if (of_property_read_bool(dev->of_node, "mux-controls")) {
+		struct mux_control *control = devm_mux_control_get(dev, NULL);
+
+		if (IS_ERR(control))
+			return PTR_ERR(control);
+
+		ret = mux_control_select(control, 1);
+		if (ret) {
+			dev_err(dev, "Failed to select HBMC mux\n");
+			return ret;
+		}
+	}
+
+	pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(dev);
+		goto disable_pm;
+	}
+
+	priv->ctlr.dev = dev;
+	priv->ctlr.ops = &am654_hbmc_ops;
+	priv->hbdev.ctlr = &priv->ctlr;
+	priv->hbdev.np = of_get_next_child(dev->of_node, NULL);
+	ret = hyperbus_register_device(&priv->hbdev);
+	if (ret) {
+		dev_err(dev, "failed to register controller\n");
+		pm_runtime_put_sync(&pdev->dev);
+		goto disable_pm;
+	}
+
+	return 0;
+disable_pm:
+	pm_runtime_disable(dev);
+	return ret;
+}
+
+static int am654_hbmc_remove(struct platform_device *pdev)
+{
+	struct am654_hbmc_priv *priv = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = hyperbus_unregister_device(&priv->hbdev);
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+
+	return ret;
+}
+
+static const struct of_device_id am654_hbmc_dt_ids[] = {
+	{
+		.compatible = "ti,am654-hbmc",
+	},
+	{ /* end of table */ }
+};
+
+MODULE_DEVICE_TABLE(of, am654_hbmc_dt_ids);
+
+static struct platform_driver am654_hbmc_platform_driver = {
+	.probe = am654_hbmc_probe,
+	.remove = am654_hbmc_remove,
+	.driver = {
+		.name = "hbmc-am654",
+		.of_match_table = am654_hbmc_dt_ids,
+	},
+};
+
+module_platform_driver(am654_hbmc_platform_driver);
+
+MODULE_DESCRIPTION("HBMC driver for AM654 SoC");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hbmc-am654");
+MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>");
-- 
2.21.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply related	[flat|nested] 24+ messages in thread
* [PATCH v6 5/5] mtd: hyperbus: Add driver for TI's HyperBus memory controller
@ 2019-06-18  9:29   ` Vignesh Raghavendra
  0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2019-06-18  9:29 UTC (permalink / raw)
  To: Vignesh Raghavendra, David Woodhouse, Brian Norris,
	Boris Brezillon, Marek Vasut, Richard Weinberger, Rob Herring
  Cc: devicetree, Sergei Shtylyov, Tudor Ambarus, linux-kernel,
	Joakim Tjernlund, linux-mtd, Miquel Raynal, Mason Yang,
	linux-arm-kernel

Add driver for HyperBus memory controller on TI's AM654 SoC. Programming
IP is pretty simple and provides direct memory mapped access to
connected Flash devices.

Add basic support for the IP without DMA. Second chipSelect is not
supported for now.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
v6: Move calibration routine here from core.

 drivers/mtd/hyperbus/Kconfig      |  12 +++
 drivers/mtd/hyperbus/Makefile     |   1 +
 drivers/mtd/hyperbus/hbmc-am654.c | 141 ++++++++++++++++++++++++++++++
 3 files changed, 154 insertions(+)
 create mode 100644 drivers/mtd/hyperbus/hbmc-am654.c

diff --git a/drivers/mtd/hyperbus/Kconfig b/drivers/mtd/hyperbus/Kconfig
index 98147e28caa0..cff6bbd226f5 100644
--- a/drivers/mtd/hyperbus/Kconfig
+++ b/drivers/mtd/hyperbus/Kconfig
@@ -9,3 +9,15 @@ menuconfig MTD_HYPERBUS
 	  the HyperBus Controller driver to communicate with
 	  HyperFlash. See Cypress HyperBus specification for more
 	  details
+
+if MTD_HYPERBUS
+
+config HBMC_AM654
+	tristate "HyperBus controller driver for AM65x SoC"
+	select MULTIPLEXER
+	select MUX_MMIO
+	help
+	 This is the driver for HyperBus controller on TI's AM65x and
+	 other SoCs
+
+endif # MTD_HYPERBUS
diff --git a/drivers/mtd/hyperbus/Makefile b/drivers/mtd/hyperbus/Makefile
index ca61dedd730d..8a936e066f48 100644
--- a/drivers/mtd/hyperbus/Makefile
+++ b/drivers/mtd/hyperbus/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0
 
 obj-$(CONFIG_MTD_HYPERBUS)	+= hyperbus-core.o
+obj-$(CONFIG_HBMC_AM654)	+= hbmc-am654.o
diff --git a/drivers/mtd/hyperbus/hbmc-am654.c b/drivers/mtd/hyperbus/hbmc-am654.c
new file mode 100644
index 000000000000..ca3fe198169e
--- /dev/null
+++ b/drivers/mtd/hyperbus/hbmc-am654.c
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Author: Vignesh Raghavendra <vigneshr@ti.com>
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/hyperbus.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mux/consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/types.h>
+
+#define AM654_HBMC_CALIB_COUNT 25
+
+struct am654_hbmc_priv {
+	struct hyperbus_ctlr ctlr;
+	struct hyperbus_device hbdev;
+};
+
+static int am654_hbmc_calibrate(struct hyperbus_device *hbdev)
+{
+	struct map_info *map = &hbdev->map;
+	struct cfi_private cfi;
+	int count = AM654_HBMC_CALIB_COUNT;
+	int pass_count = 0;
+	int ret;
+
+	cfi.interleave = 1;
+	cfi.device_type = CFI_DEVICETYPE_X16;
+	cfi_send_gen_cmd(0xF0, 0, 0, map, &cfi, cfi.device_type, NULL);
+	cfi_send_gen_cmd(0x98, 0x55, 0, map, &cfi, cfi.device_type, NULL);
+
+	while (count--) {
+		ret = cfi_qry_present(map, 0, &cfi);
+		if (ret)
+			pass_count++;
+		else
+			pass_count = 0;
+		if (pass_count == 5)
+			break;
+	}
+
+	cfi_qry_mode_off(0, map, &cfi);
+
+	return ret;
+}
+
+static const struct hyperbus_ops am654_hbmc_ops = {
+	.calibrate = am654_hbmc_calibrate,
+};
+
+static int am654_hbmc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct am654_hbmc_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, priv);
+
+	if (of_property_read_bool(dev->of_node, "mux-controls")) {
+		struct mux_control *control = devm_mux_control_get(dev, NULL);
+
+		if (IS_ERR(control))
+			return PTR_ERR(control);
+
+		ret = mux_control_select(control, 1);
+		if (ret) {
+			dev_err(dev, "Failed to select HBMC mux\n");
+			return ret;
+		}
+	}
+
+	pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(dev);
+		goto disable_pm;
+	}
+
+	priv->ctlr.dev = dev;
+	priv->ctlr.ops = &am654_hbmc_ops;
+	priv->hbdev.ctlr = &priv->ctlr;
+	priv->hbdev.np = of_get_next_child(dev->of_node, NULL);
+	ret = hyperbus_register_device(&priv->hbdev);
+	if (ret) {
+		dev_err(dev, "failed to register controller\n");
+		pm_runtime_put_sync(&pdev->dev);
+		goto disable_pm;
+	}
+
+	return 0;
+disable_pm:
+	pm_runtime_disable(dev);
+	return ret;
+}
+
+static int am654_hbmc_remove(struct platform_device *pdev)
+{
+	struct am654_hbmc_priv *priv = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = hyperbus_unregister_device(&priv->hbdev);
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+
+	return ret;
+}
+
+static const struct of_device_id am654_hbmc_dt_ids[] = {
+	{
+		.compatible = "ti,am654-hbmc",
+	},
+	{ /* end of table */ }
+};
+
+MODULE_DEVICE_TABLE(of, am654_hbmc_dt_ids);
+
+static struct platform_driver am654_hbmc_platform_driver = {
+	.probe = am654_hbmc_probe,
+	.remove = am654_hbmc_remove,
+	.driver = {
+		.name = "hbmc-am654",
+		.of_match_table = am654_hbmc_dt_ids,
+	},
+};
+
+module_platform_driver(am654_hbmc_platform_driver);
+
+MODULE_DESCRIPTION("HBMC driver for AM654 SoC");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:hbmc-am654");
+MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>");
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 24+ messages in thread
end of thread, other threads:[~2019-06-18  9:32 UTC | newest]

Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-06-18  9:28 [PATCH v6 0/5] MTD: Add Initial Hyperbus support Vignesh Raghavendra
2019-06-18  9:28 ` Vignesh Raghavendra
2019-06-18  9:28 ` Vignesh Raghavendra
2019-06-18  9:28 ` Vignesh Raghavendra
2019-06-18  9:28 ` [PATCH v6 1/5] mtd: cfi_cmdset_0002: Add support for polling status register Vignesh Raghavendra
2019-06-18  9:28   ` Vignesh Raghavendra
2019-06-18  9:28   ` Vignesh Raghavendra
2019-06-18  9:28   ` Vignesh Raghavendra
2019-06-18  9:28 ` [PATCH v6 2/5] dt-bindings: mtd: Add binding documentation for HyperFlash Vignesh Raghavendra
2019-06-18  9:28   ` Vignesh Raghavendra
2019-06-18  9:28   ` Vignesh Raghavendra
2019-06-18  9:28   ` Vignesh Raghavendra
2019-06-18  9:28 ` [PATCH v6 3/5] mtd: Add support for HyperBus memory devices Vignesh Raghavendra
2019-06-18  9:28   ` Vignesh Raghavendra
2019-06-18  9:28   ` Vignesh Raghavendra
2019-06-18  9:28   ` Vignesh Raghavendra
2019-06-18  9:29 ` [PATCH v6 4/5] dt-bindings: mtd: Add bindings for TI's AM654 HyperBus memory controller Vignesh Raghavendra
2019-06-18  9:29   ` Vignesh Raghavendra
2019-06-18  9:29   ` Vignesh Raghavendra
2019-06-18  9:29   ` Vignesh Raghavendra
2019-06-18  9:29 ` [PATCH v6 5/5] mtd: hyperbus: Add driver for TI's " Vignesh Raghavendra
2019-06-18  9:29   ` Vignesh Raghavendra
2019-06-18  9:29   ` Vignesh Raghavendra
2019-06-18  9:29   ` Vignesh Raghavendra

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.