[PATCH AUTOSEL 4.4 01/44] ALSA: hda: Flush interrupts on disabling

[PATCH AUTOSEL 4.4 01/44] ALSA: hda: Flush interrupts on disabling

[Sasha Levin]

From: Chris Wilson <chris@chris-wilson.co.uk>

[ Upstream commit caa8422d01e983782548648e125fd617cadcec3f ]

I was looking at

<4> [241.835158] general protection fault: 0000 [#1] PREEMPT SMP PTI
<4> [241.835181] CPU: 1 PID: 214 Comm: kworker/1:3 Tainted: G     U            5.2.0-CI-CI_DRM_6509+ #1
<4> [241.835199] Hardware name: Dell Inc.                 OptiPlex 745                 /0GW726, BIOS 2.3.1  05/21/2007
<4> [241.835234] Workqueue: events snd_hdac_bus_process_unsol_events [snd_hda_core]
<4> [241.835256] RIP: 0010:input_handle_event+0x16d/0x5e0
<4> [241.835270] Code: 48 8b 93 58 01 00 00 8b 52 08 89 50 04 8b 83 f8 06 00 00 48 8b 93 00 07 00 00 8d 70 01 48 8d 04 c2 83 e1 08 89 b3 f8 06 00 00 <66> 89 28 66 44 89 60 02 44 89 68 04 8b 93 f8 06 00 00 0f 84 fd fe
<4> [241.835304] RSP: 0018:ffffc9000019fda0 EFLAGS: 00010046
<4> [241.835317] RAX: 6b6b6b6ec6c6c6c3 RBX: ffff8880290fefc8 RCX: 0000000000000000
<4> [241.835332] RDX: 000000006b6b6b6b RSI: 000000006b6b6b6c RDI: 0000000000000046
<4> [241.835347] RBP: 0000000000000005 R08: 0000000000000000 R09: 0000000000000001
<4> [241.835362] R10: ffffc9000019faa0 R11: 0000000000000000 R12: 0000000000000004
<4> [241.835377] R13: 0000000000000000 R14: ffff8880290ff1d0 R15: 0000000000000293
<4> [241.835392] FS:  0000000000000000(0000) GS:ffff88803de80000(0000) knlGS:0000000000000000
<4> [241.835409] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [241.835422] CR2: 00007ffe9a99e9b7 CR3: 000000002f588000 CR4: 00000000000006e0
<4> [241.835436] Call Trace:
<4> [241.835449]  input_event+0x45/0x70
<4> [241.835464]  snd_jack_report+0xdc/0x100
<4> [241.835490]  snd_hda_jack_report_sync+0x83/0xc0 [snd_hda_codec]
<4> [241.835512]  snd_hdac_bus_process_unsol_events+0x5a/0x70 [snd_hda_core]
<4> [241.835530]  process_one_work+0x245/0x610

which has the hallmarks of a worker queued from interrupt after it was
supposedly cancelled (note the POISON_FREE), and I could not see where
the interrupt would be flushed on shutdown so added the likely suspects.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111174
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/hda/hdac_controller.c | 2 ++
 sound/pci/hda/hda_intel.c   | 2 +-
 2 files changed, 3 insertions(+), 1 deletion(-)

diff --git a/sound/hda/hdac_controller.c b/sound/hda/hdac_controller.c
index 4727f5b80e76d..acc2c7dbfb151 100644
--- a/sound/hda/hdac_controller.c
+++ b/sound/hda/hdac_controller.c
@@ -340,6 +340,8 @@ static void azx_int_disable(struct hdac_bus *bus)
 	list_for_each_entry(azx_dev, &bus->stream_list, list)
 		snd_hdac_stream_updateb(azx_dev, SD_CTL, SD_INT_MASK, 0);
 
+	synchronize_irq(bus->irq);
+
 	/* disable SIE for all streams */
 	snd_hdac_chip_writeb(bus, INTCTL, 0);
 
diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c
index ef8955abd9186..96ccab15da836 100644
--- a/sound/pci/hda/hda_intel.c
+++ b/sound/pci/hda/hda_intel.c
@@ -1274,9 +1274,9 @@ static int azx_free(struct azx *chip)
 	}
 
 	if (bus->chip_init) {
+		azx_stop_chip(chip);
 		azx_clear_irq_pending(chip);
 		azx_stop_all_streams(chip);
-		azx_stop_chip(chip);
 	}
 
 	if (bus->irq >= 0)
-- 
2.20.1

[PATCH AUTOSEL 4.4 02/44] ASoC: sgtl5000: Fix charge pump source assignment

[Sasha Levin]

From: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

[ Upstream commit b6319b061ba279577fd7030a9848fbd6a17151e3 ]

If VDDA != VDDIO and any of them is greater than 3.1V, charge pump
source can be assigned automatically [1].

[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-7-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/sgtl5000.c | 15 ++++++++++-----
 1 file changed, 10 insertions(+), 5 deletions(-)

diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
index 08b40460663c2..549f853c40924 100644
--- a/sound/soc/codecs/sgtl5000.c
+++ b/sound/soc/codecs/sgtl5000.c
@@ -1166,12 +1166,17 @@ static int sgtl5000_set_power_regs(struct snd_soc_codec *codec)
 					SGTL5000_INT_OSC_EN);
 		/* Enable VDDC charge pump */
 		ana_pwr |= SGTL5000_VDDC_CHRGPMP_POWERUP;
-	} else if (vddio >= 3100 && vdda >= 3100) {
+	} else {
 		ana_pwr &= ~SGTL5000_VDDC_CHRGPMP_POWERUP;
-		/* VDDC use VDDIO rail */
-		lreg_ctrl |= SGTL5000_VDDC_ASSN_OVRD;
-		lreg_ctrl |= SGTL5000_VDDC_MAN_ASSN_VDDIO <<
-			    SGTL5000_VDDC_MAN_ASSN_SHIFT;
+		/*
+		 * if vddio == vdda the source of charge pump should be
+		 * assigned manually to VDDIO
+		 */
+		if (vddio == vdda) {
+			lreg_ctrl |= SGTL5000_VDDC_ASSN_OVRD;
+			lreg_ctrl |= SGTL5000_VDDC_MAN_ASSN_VDDIO <<
+				    SGTL5000_VDDC_MAN_ASSN_SHIFT;
+		}
 	}
 
 	snd_soc_write(codec, SGTL5000_CHIP_LINREG_CTRL, lreg_ctrl);
-- 
2.20.1

[PATCH AUTOSEL 4.4 03/44] dmaengine: bcm2835: Print error in case setting DMA mask fails

[Sasha Levin]

From: Stefan Wahren <wahrenst@gmx.net>

[ Upstream commit 72503b25ee363827aafffc3e8d872e6a92a7e422 ]

During enabling of the RPi 4, we found out that the driver doesn't provide
a helpful error message in case setting DMA mask fails. So add one.

Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/1563297318-4900-1-git-send-email-wahrenst@gmx.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/dma/bcm2835-dma.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/dma/bcm2835-dma.c b/drivers/dma/bcm2835-dma.c
index 996c4b00d323e..d6cdc3be03fcc 100644
--- a/drivers/dma/bcm2835-dma.c
+++ b/drivers/dma/bcm2835-dma.c
@@ -595,8 +595,10 @@ static int bcm2835_dma_probe(struct platform_device *pdev)
 		pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
 
 	rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
-	if (rc)
+	if (rc) {
+		dev_err(&pdev->dev, "Unable to set DMA mask\n");
 		return rc;
+	}
 
 	od = devm_kzalloc(&pdev->dev, sizeof(*od), GFP_KERNEL);
 	if (!od)
-- 
2.20.1

[PATCH AUTOSEL 4.4 04/44] leds: leds-lp5562 allow firmware files up to the maximum length

[Sasha Levin]

From: Nick Stoughton <nstoughton@logitech.com>

[ Upstream commit ed2abfebb041473092b41527903f93390d38afa7 ]

Firmware files are in ASCII, using 2 hex characters per byte. The
maximum length of a firmware string is therefore

16 (commands) * 2 (bytes per command) * 2 (characters per byte) = 64

Fixes: ff45262a85db ("leds: add new LP5562 LED driver")
Signed-off-by: Nick Stoughton <nstoughton@logitech.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/leds/leds-lp5562.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/leds/leds-lp5562.c b/drivers/leds/leds-lp5562.c
index 0360c59dbdc91..fc8b2e7bcfef6 100644
--- a/drivers/leds/leds-lp5562.c
+++ b/drivers/leds/leds-lp5562.c
@@ -263,7 +263,11 @@ static void lp5562_firmware_loaded(struct lp55xx_chip *chip)
 {
 	const struct firmware *fw = chip->fw;
 
-	if (fw->size > LP5562_PROGRAM_LENGTH) {
+	/*
+	 * the firmware is encoded in ascii hex character, with 2 chars
+	 * per byte
+	 */
+	if (fw->size > (LP5562_PROGRAM_LENGTH * 2)) {
 		dev_err(&chip->cl->dev, "firmware data size overflow: %zu\n",
 			fw->size);
 		return;
-- 
2.20.1

[PATCH AUTOSEL 4.4 05/44] media: dib0700: fix link error for dibx000_i2c_set_speed

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit 765bb8610d305ee488b35d07e2a04ae52fb2df9c ]

When CONFIG_DVB_DIB9000 is disabled, we can still compile code that
now fails to link against dibx000_i2c_set_speed:

drivers/media/usb/dvb-usb/dib0700_devices.o: In function `dib01x0_pmu_update.constprop.7':
dib0700_devices.c:(.text.unlikely+0x1c9c): undefined reference to `dibx000_i2c_set_speed'

The call sites are both through dib01x0_pmu_update(), which gets passed
an 'i2c' pointer from dib9000_get_i2c_master(), which has returned
NULL. Checking this pointer seems to be a good idea anyway, and it avoids
the link failure in most cases.

Sean Young found another case that is not fixed by that, where certain
gcc versions leave an unused function in place that causes the link error,
but adding an explict IS_ENABLED() check also solves this.

Fixes: b7f54910ce01 ("V4L/DVB (4647): Added module for DiB0700 based devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/dvb-usb/dib0700_devices.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/media/usb/dvb-usb/dib0700_devices.c b/drivers/media/usb/dvb-usb/dib0700_devices.c
index 38c03283a4417..e1316c7b7c2e5 100644
--- a/drivers/media/usb/dvb-usb/dib0700_devices.c
+++ b/drivers/media/usb/dvb-usb/dib0700_devices.c
@@ -2418,9 +2418,13 @@ static int dib9090_tuner_attach(struct dvb_usb_adapter *adap)
 		8, 0x0486,
 	};
 
+	if (!IS_ENABLED(CONFIG_DVB_DIB9000))
+		return -ENODEV;
 	if (dvb_attach(dib0090_fw_register, adap->fe_adap[0].fe, i2c, &dib9090_dib0090_config) == NULL)
 		return -ENODEV;
 	i2c = dib9000_get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_GPIO_1_2, 0);
+	if (!i2c)
+		return -ENODEV;
 	if (dib01x0_pmu_update(i2c, data_dib190, 10) != 0)
 		return -ENODEV;
 	dib0700_set_i2c_speed(adap->dev, 1500);
@@ -2496,10 +2500,14 @@ static int nim9090md_tuner_attach(struct dvb_usb_adapter *adap)
 		0, 0x00ef,
 		8, 0x0406,
 	};
+	if (!IS_ENABLED(CONFIG_DVB_DIB9000))
+		return -ENODEV;
 	i2c = dib9000_get_tuner_interface(adap->fe_adap[0].fe);
 	if (dvb_attach(dib0090_fw_register, adap->fe_adap[0].fe, i2c, &nim9090md_dib0090_config[0]) == NULL)
 		return -ENODEV;
 	i2c = dib9000_get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_GPIO_1_2, 0);
+	if (!i2c)
+		return -ENODEV;
 	if (dib01x0_pmu_update(i2c, data_dib190, 10) < 0)
 		return -ENODEV;
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 06/44] media: hdpvr: Add device num check and handling

[Sasha Levin]

From: Luke Nowakowski-Krijger <lnowakow@eng.ucsd.edu>

[ Upstream commit d4a6a9537bc32811486282206ecfb7c53754b74d ]

Add hdpvr device num check and error handling

We need to increment the device count atomically before we checkout a
device to make sure that we do not reach the max count, otherwise we get
out-of-bounds errors as reported by syzbot.

Reported-and-tested-by: syzbot+aac8d0d7205f112045d2@syzkaller.appspotmail.com

Signed-off-by: Luke Nowakowski-Krijger <lnowakow@eng.ucsd.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/hdpvr/hdpvr-core.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)

diff --git a/drivers/media/usb/hdpvr/hdpvr-core.c b/drivers/media/usb/hdpvr/hdpvr-core.c
index 08f0ca7aa012e..924517b09fc9f 100644
--- a/drivers/media/usb/hdpvr/hdpvr-core.c
+++ b/drivers/media/usb/hdpvr/hdpvr-core.c
@@ -278,6 +278,7 @@ static int hdpvr_probe(struct usb_interface *interface,
 #endif
 	size_t buffer_size;
 	int i;
+	int dev_num;
 	int retval = -ENOMEM;
 
 	/* allocate memory for our device state and initialize it */
@@ -386,8 +387,17 @@ static int hdpvr_probe(struct usb_interface *interface,
 	}
 #endif
 
+	dev_num = atomic_inc_return(&dev_nr);
+	if (dev_num >= HDPVR_MAX) {
+		v4l2_err(&dev->v4l2_dev,
+			 "max device number reached, device register failed\n");
+		atomic_dec(&dev_nr);
+		retval = -ENODEV;
+		goto reg_fail;
+	}
+
 	retval = hdpvr_register_videodev(dev, &interface->dev,
-				    video_nr[atomic_inc_return(&dev_nr)]);
+				    video_nr[dev_num]);
 	if (retval < 0) {
 		v4l2_err(&dev->v4l2_dev, "registering videodev failed\n");
 		goto reg_fail;
-- 
2.20.1

[PATCH AUTOSEL 4.4 07/44] sched/fair: Fix imbalance due to CPU affinity

[Sasha Levin]

From: Vincent Guittot <vincent.guittot@linaro.org>

[ Upstream commit f6cad8df6b30a5d2bbbd2e698f74b4cafb9fb82b ]

The load_balance() has a dedicated mecanism to detect when an imbalance
is due to CPU affinity and must be handled at parent level. In this case,
the imbalance field of the parent's sched_group is set.

The description of sg_imbalanced() gives a typical example of two groups
of 4 CPUs each and 4 tasks each with a cpumask covering 1 CPU of the first
group and 3 CPUs of the second group. Something like:

	{ 0 1 2 3 } { 4 5 6 7 }
	        *     * * *

But the load_balance fails to fix this UC on my octo cores system
made of 2 clusters of quad cores.

Whereas the load_balance is able to detect that the imbalanced is due to
CPU affinity, it fails to fix it because the imbalance field is cleared
before letting parent level a chance to run. In fact, when the imbalance is
detected, the load_balance reruns without the CPU with pinned tasks. But
there is no other running tasks in the situation described above and
everything looks balanced this time so the imbalance field is immediately
cleared.

The imbalance field should not be cleared if there is no other task to move
when the imbalance is detected.

Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1561996022-28829-1-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/sched/fair.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/kernel/sched/fair.c b/kernel/sched/fair.c
index 19d735ab44db4..cd2fb8384fbe3 100644
--- a/kernel/sched/fair.c
+++ b/kernel/sched/fair.c
@@ -7313,9 +7313,10 @@ static int load_balance(int this_cpu, struct rq *this_rq,
 out_balanced:
 	/*
 	 * We reach balance although we may have faced some affinity
-	 * constraints. Clear the imbalance flag if it was set.
+	 * constraints. Clear the imbalance flag only if other tasks got
+	 * a chance to move and fix the imbalance.
 	 */
-	if (sd_parent) {
+	if (sd_parent && !(env.flags & LBF_ALL_PINNED)) {
 		int *group_imbalance = &sd_parent->groups->sgc->imbalance;
 
 		if (*group_imbalance)
-- 
2.20.1

[PATCH AUTOSEL 4.4 08/44] sched/core: Fix CPU controller for !RT_GROUP_SCHED

[Sasha Levin]

From: Juri Lelli <juri.lelli@redhat.com>

[ Upstream commit a07db5c0865799ebed1f88be0df50c581fb65029 ]

On !CONFIG_RT_GROUP_SCHED configurations it is currently not possible to
move RT tasks between cgroups to which CPU controller has been attached;
but it is oddly possible to first move tasks around and then make them
RT (setschedule to FIFO/RR).

E.g.:

  # mkdir /sys/fs/cgroup/cpu,cpuacct/group1
  # chrt -fp 10 $$
  # echo $$ > /sys/fs/cgroup/cpu,cpuacct/group1/tasks
  bash: echo: write error: Invalid argument
  # chrt -op 0 $$
  # echo $$ > /sys/fs/cgroup/cpu,cpuacct/group1/tasks
  # chrt -fp 10 $$
  # cat /sys/fs/cgroup/cpu,cpuacct/group1/tasks
  2345
  2598
  # chrt -p 2345
  pid 2345's current scheduling policy: SCHED_FIFO
  pid 2345's current scheduling priority: 10

Also, as Michal noted, it is currently not possible to enable CPU
controller on unified hierarchy with !CONFIG_RT_GROUP_SCHED (if there
are any kernel RT threads in root cgroup, they can't be migrated to the
newly created CPU controller's root in cgroup_update_dfl_csses()).

Existing code comes with a comment saying the "we don't support RT-tasks
being in separate groups". Such comment is however stale and belongs to
pre-RT_GROUP_SCHED times. Also, it doesn't make much sense for
!RT_GROUP_ SCHED configurations, since checks related to RT bandwidth
are not performed at all in these cases.

Make moving RT tasks between CPU controller groups viable by removing
special case check for RT (and DEADLINE) tasks.

Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: lizefan@huawei.com
Cc: longman@redhat.com
Cc: luca.abeni@santannapisa.it
Cc: rostedt@goodmis.org
Link: https://lkml.kernel.org/r/20190719063455.27328-1-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/sched/core.c | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/kernel/sched/core.c b/kernel/sched/core.c
index 0e70bfeded7fd..d81bcc6362fff 100644
--- a/kernel/sched/core.c
+++ b/kernel/sched/core.c
@@ -8339,10 +8339,6 @@ static int cpu_cgroup_can_attach(struct cgroup_taskset *tset)
 #ifdef CONFIG_RT_GROUP_SCHED
 		if (!sched_rt_can_attach(css_tg(css), task))
 			return -EINVAL;
-#else
-		/* We don't support RT-tasks being in separate groups */
-		if (task->sched_class != &fair_sched_class)
-			return -EINVAL;
 #endif
 	}
 	return 0;
-- 
2.20.1

[PATCH AUTOSEL 4.4 09/44] x86/reboot: Always use NMI fallback when shutdown via reboot vector IPI fails

[Sasha Levin]

From: Grzegorz Halat <ghalat@redhat.com>

[ Upstream commit 747d5a1bf293dcb33af755a6d285d41b8c1ea010 ]

A reboot request sends an IPI via the reboot vector and waits for all other
CPUs to stop. If one or more CPUs are in critical regions with interrupts
disabled then the IPI is not handled on those CPUs and the shutdown hangs
if native_stop_other_cpus() is called with the wait argument set.

Such a situation can happen when one CPU was stopped within a lock held
section and another CPU is trying to acquire that lock with interrupts
disabled. There are other scenarios which can cause such a lockup as well.

In theory the shutdown should be attempted by an NMI IPI after the timeout
period elapsed. Though the wait loop after sending the reboot vector IPI
prevents this. It checks the wait request argument and the timeout. If wait
is set, which is true for sys_reboot() then it won't fall through to the
NMI shutdown method after the timeout period has finished.

This was an oversight when the NMI shutdown mechanism was added to handle
the 'reboot IPI is not working' situation. The mechanism was added to deal
with stuck panic shutdowns, which do not have the wait request set, so the
'wait request' case was probably not considered.

Remove the wait check from the post reboot vector IPI wait loop and enforce
that the wait loop in the NMI fallback path is invoked even if NMI IPIs are
disabled or the registration of the NMI handler fails. That second wait
loop will then hang if not all CPUs shutdown and the wait argument is set.

[ tglx: Avoid the hard to parse line break in the NMI fallback path,
  	add comments and massage the changelog ]

Fixes: 7d007d21e539 ("x86/reboot: Use NMI to assist in shutting down if IRQ fails")
Signed-off-by: Grzegorz Halat <ghalat@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Don Zickus <dzickus@redhat.com>
Link: https://lkml.kernel.org/r/20190628122813.15500-1-ghalat@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/kernel/smp.c | 46 +++++++++++++++++++++++++------------------
 1 file changed, 27 insertions(+), 19 deletions(-)

diff --git a/arch/x86/kernel/smp.c b/arch/x86/kernel/smp.c
index 12c8286206ce2..6a0ba9d09b0ed 100644
--- a/arch/x86/kernel/smp.c
+++ b/arch/x86/kernel/smp.c
@@ -176,6 +176,12 @@ asmlinkage __visible void smp_reboot_interrupt(void)
 	irq_exit();
 }
 
+static int register_stop_handler(void)
+{
+	return register_nmi_handler(NMI_LOCAL, smp_stop_nmi_callback,
+				    NMI_FLAG_FIRST, "smp_stop");
+}
+
 static void native_stop_other_cpus(int wait)
 {
 	unsigned long flags;
@@ -209,39 +215,41 @@ static void native_stop_other_cpus(int wait)
 		apic->send_IPI_allbutself(REBOOT_VECTOR);
 
 		/*
-		 * Don't wait longer than a second if the caller
-		 * didn't ask us to wait.
+		 * Don't wait longer than a second for IPI completion. The
+		 * wait request is not checked here because that would
+		 * prevent an NMI shutdown attempt in case that not all
+		 * CPUs reach shutdown state.
 		 */
 		timeout = USEC_PER_SEC;
-		while (num_online_cpus() > 1 && (wait || timeout--))
+		while (num_online_cpus() > 1 && timeout--)
 			udelay(1);
 	}
-	
-	/* if the REBOOT_VECTOR didn't work, try with the NMI */
-	if ((num_online_cpus() > 1) && (!smp_no_nmi_ipi))  {
-		if (register_nmi_handler(NMI_LOCAL, smp_stop_nmi_callback,
-					 NMI_FLAG_FIRST, "smp_stop"))
-			/* Note: we ignore failures here */
-			/* Hope the REBOOT_IRQ is good enough */
-			goto finish;
-
-		/* sync above data before sending IRQ */
-		wmb();
 
-		pr_emerg("Shutting down cpus with NMI\n");
+	/* if the REBOOT_VECTOR didn't work, try with the NMI */
+	if (num_online_cpus() > 1) {
+		/*
+		 * If NMI IPI is enabled, try to register the stop handler
+		 * and send the IPI. In any case try to wait for the other
+		 * CPUs to stop.
+		 */
+		if (!smp_no_nmi_ipi && !register_stop_handler()) {
+			/* Sync above data before sending IRQ */
+			wmb();
 
-		apic->send_IPI_allbutself(NMI_VECTOR);
+			pr_emerg("Shutting down cpus with NMI\n");
 
+			apic->send_IPI_allbutself(NMI_VECTOR);
+		}
 		/*
-		 * Don't wait longer than a 10 ms if the caller
-		 * didn't ask us to wait.
+		 * Don't wait longer than 10 ms if the caller didn't
+		 * reqeust it. If wait is true, the machine hangs here if
+		 * one or more CPUs do not reach shutdown state.
 		 */
 		timeout = USEC_PER_MSEC * 10;
 		while (num_online_cpus() > 1 && (wait || timeout--))
 			udelay(1);
 	}
 
-finish:
 	local_irq_save(flags);
 	disable_local_APIC();
 	mcheck_cpu_clear(this_cpu_ptr(&cpu_info));
-- 
2.20.1

[PATCH AUTOSEL 4.4 10/44] x86/apic: Soft disable APIC before initializing it

[Sasha Levin]

From: Thomas Gleixner <tglx@linutronix.de>

[ Upstream commit 2640da4cccf5cc613bf26f0998b9e340f4b5f69c ]

If the APIC was already enabled on entry of setup_local_APIC() then
disabling it soft via the SPIV register makes a lot of sense.

That masks all LVT entries and brings it into a well defined state.

Otherwise previously enabled LVTs which are not touched in the setup
function stay unmasked and might surprise the just booting kernel.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190722105219.068290579@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/kernel/apic/apic.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/x86/kernel/apic/apic.c b/arch/x86/kernel/apic/apic.c
index 834d1b5b43557..be3d4dcf3a10a 100644
--- a/arch/x86/kernel/apic/apic.c
+++ b/arch/x86/kernel/apic/apic.c
@@ -1265,6 +1265,14 @@ void setup_local_APIC(void)
 		return;
 	}
 
+	/*
+	 * If this comes from kexec/kcrash the APIC might be enabled in
+	 * SPIV. Soft disable it before doing further initialization.
+	 */
+	value = apic_read(APIC_SPIV);
+	value &= ~APIC_SPIV_APIC_ENABLED;
+	apic_write(APIC_SPIV, value);
+
 #ifdef CONFIG_X86_32
 	/* Pound the ESR really hard over the head with a big hammer - mbligh */
 	if (lapic_is_integrated() && apic->disable_esr) {
-- 
2.20.1

[PATCH AUTOSEL 4.4 11/44] ALSA: hda - Show the fatal CORB/RIRB error more clearly

[Sasha Levin]

From: Takashi Iwai <tiwai@suse.de>

[ Upstream commit dd65f7e19c6961ba6a69f7c925021b7a270cb950 ]

The last fallback of CORB/RIRB communication error recovery is to turn
on the single command mode, and this last resort usually means that
something is really screwed up.  Instead of a normal dev_err(), show
the error more clearly with dev_WARN() with the caller stack trace.

Also, show the bus-reset fallback also as an error, too.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/pci/hda/hda_controller.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/sound/pci/hda/hda_controller.c b/sound/pci/hda/hda_controller.c
index 273364c39171c..9cdf86f04e037 100644
--- a/sound/pci/hda/hda_controller.c
+++ b/sound/pci/hda/hda_controller.c
@@ -667,10 +667,13 @@ static int azx_rirb_get_response(struct hdac_bus *bus, unsigned int addr,
 	 */
 	if (hbus->allow_bus_reset && !hbus->response_reset && !hbus->in_reset) {
 		hbus->response_reset = 1;
+		dev_err(chip->card->dev,
+			"No response from codec, resetting bus: last cmd=0x%08x\n",
+			bus->last_cmd[addr]);
 		return -EAGAIN; /* give a chance to retry */
 	}
 
-	dev_err(chip->card->dev,
+	dev_WARN(chip->card->dev,
 		"azx_get_response timeout, switching to single_cmd mode: last cmd=0x%08x\n",
 		bus->last_cmd[addr]);
 	chip->single_cmd = 1;
-- 
2.20.1

[PATCH AUTOSEL 4.4 12/44] ALSA: i2c: ak4xxx-adda: Fix a possible null pointer dereference in build_adc_controls()

[Sasha Levin]

From: Jia-Ju Bai <baijiaju1990@gmail.com>

[ Upstream commit 2127c01b7f63b06a21559f56a8c81a3c6535bd1a ]

In build_adc_controls(), there is an if statement on line 773 to check
whether ak->adc_info is NULL:
    if (! ak->adc_info ||
        ! ak->adc_info[mixer_ch].switch_name)

When ak->adc_info is NULL, it is used on line 792:
    knew.name = ak->adc_info[mixer_ch].selector_name;

Thus, a possible null-pointer dereference may occur.

To fix this bug, referring to lines 773 and 774, ak->adc_info
and ak->adc_info[mixer_ch].selector_name are checked before being used.

This bug is found by a static analysis tool STCheck written by us.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/i2c/other/ak4xxx-adda.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/sound/i2c/other/ak4xxx-adda.c b/sound/i2c/other/ak4xxx-adda.c
index bf377dc192aa7..d33e02c317129 100644
--- a/sound/i2c/other/ak4xxx-adda.c
+++ b/sound/i2c/other/ak4xxx-adda.c
@@ -789,11 +789,12 @@ static int build_adc_controls(struct snd_akm4xxx *ak)
 				return err;
 
 			memset(&knew, 0, sizeof(knew));
-			knew.name = ak->adc_info[mixer_ch].selector_name;
-			if (!knew.name) {
+			if (!ak->adc_info ||
+				!ak->adc_info[mixer_ch].selector_name) {
 				knew.name = "Capture Channel";
 				knew.index = mixer_ch + ak->idx_offset * 2;
-			}
+			} else
+				knew.name = ak->adc_info[mixer_ch].selector_name;
 
 			knew.iface = SNDRV_CTL_ELEM_IFACE_MIXER;
 			knew.info = ak4xxx_capture_source_info;
-- 
2.20.1

[PATCH AUTOSEL 4.4 13/44] media: iguanair: add sanity checks

[Sasha Levin]

From: Oliver Neukum <oneukum@suse.com>

[ Upstream commit ab1cbdf159beba7395a13ab70bc71180929ca064 ]

The driver needs to check the endpoint types, too, as opposed
to the number of endpoints. This also requires moving the check earlier.

Reported-by: syzbot+01a77b82edaa374068e1@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/rc/iguanair.c | 15 +++++++--------
 1 file changed, 7 insertions(+), 8 deletions(-)

diff --git a/drivers/media/rc/iguanair.c b/drivers/media/rc/iguanair.c
index ee60e17fba05d..cda4ce612dcf5 100644
--- a/drivers/media/rc/iguanair.c
+++ b/drivers/media/rc/iguanair.c
@@ -430,6 +430,10 @@ static int iguanair_probe(struct usb_interface *intf,
 	int ret, pipein, pipeout;
 	struct usb_host_interface *idesc;
 
+	idesc = intf->altsetting;
+	if (idesc->desc.bNumEndpoints < 2)
+		return -ENODEV;
+
 	ir = kzalloc(sizeof(*ir), GFP_KERNEL);
 	rc = rc_allocate_device();
 	if (!ir || !rc) {
@@ -444,18 +448,13 @@ static int iguanair_probe(struct usb_interface *intf,
 	ir->urb_in = usb_alloc_urb(0, GFP_KERNEL);
 	ir->urb_out = usb_alloc_urb(0, GFP_KERNEL);
 
-	if (!ir->buf_in || !ir->packet || !ir->urb_in || !ir->urb_out) {
+	if (!ir->buf_in || !ir->packet || !ir->urb_in || !ir->urb_out ||
+	    !usb_endpoint_is_int_in(&idesc->endpoint[0].desc) ||
+	    !usb_endpoint_is_int_out(&idesc->endpoint[1].desc)) {
 		ret = -ENOMEM;
 		goto out;
 	}
 
-	idesc = intf->altsetting;
-
-	if (idesc->desc.bNumEndpoints < 2) {
-		ret = -ENODEV;
-		goto out;
-	}
-
 	ir->rc = rc;
 	ir->dev = &intf->dev;
 	ir->udev = udev;
-- 
2.20.1

[PATCH AUTOSEL 4.4 14/44] base: soc: Export soc_device_register/unregister APIs

[Sasha Levin]

From: Vinod Koul <vkoul@kernel.org>

[ Upstream commit f7ccc7a397cf2ef64aebb2f726970b93203858d2 ]

Qcom Socinfo driver can be built as a module, so
export these two APIs.

Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/base/soc.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/base/soc.c b/drivers/base/soc.c
index 75b98aad6fafd..84242e6b2897f 100644
--- a/drivers/base/soc.c
+++ b/drivers/base/soc.c
@@ -146,6 +146,7 @@ struct soc_device *soc_device_register(struct soc_device_attribute *soc_dev_attr
 out1:
 	return ERR_PTR(ret);
 }
+EXPORT_SYMBOL_GPL(soc_device_register);
 
 /* Ensure soc_dev->attr is freed prior to calling soc_device_unregister. */
 void soc_device_unregister(struct soc_device *soc_dev)
@@ -154,6 +155,7 @@ void soc_device_unregister(struct soc_device *soc_dev)
 
 	device_unregister(&soc_dev->dev);
 }
+EXPORT_SYMBOL_GPL(soc_device_unregister);
 
 static int __init soc_bus_register(void)
 {
-- 
2.20.1

[PATCH AUTOSEL 4.4 15/44] ALSA: usb-audio: Skip bSynchAddress endpoint check if it is invalid

[Sasha Levin]

From: Ard van Breemen <ard@kwaak.net>

[ Upstream commit 1b34121d9f26d272b0b2334209af6b6fc82d4bf1 ]

The Linux kernel assumes that get_endpoint(alts,0) and
get_endpoint(alts,1) are eachothers feedback endpoints.
To reassure that validity it will test bsynchaddress to comply with that
assumption. But if the bsyncaddress is 0 (invalid), it will flag that as
a wrong assumption and return an error.
Fix: Skip the test if bSynchAddress is 0.
Note: those with a valid bSynchAddress should have a code quirck added.

Signed-off-by: Ard van Breemen <ard@kwaak.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/usb/pcm.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/sound/usb/pcm.c b/sound/usb/pcm.c
index 1ea1384bc2369..f84c55ecd0fb4 100644
--- a/sound/usb/pcm.c
+++ b/sound/usb/pcm.c
@@ -460,6 +460,7 @@ static int set_sync_endpoint(struct snd_usb_substream *subs,
 	}
 	ep = get_endpoint(alts, 1)->bEndpointAddress;
 	if (get_endpoint(alts, 0)->bLength >= USB_DT_ENDPOINT_AUDIO_SIZE &&
+	    get_endpoint(alts, 0)->bSynchAddress != 0 &&
 	    ((is_playback && ep != (unsigned int)(get_endpoint(alts, 0)->bSynchAddress | USB_DIR_IN)) ||
 	     (!is_playback && ep != (unsigned int)(get_endpoint(alts, 0)->bSynchAddress & ~USB_DIR_IN)))) {
 		dev_err(&dev->dev,
-- 
2.20.1

[PATCH AUTOSEL 4.4 16/44] ia64:unwind: fix double free for mod->arch.init_unw_table

[Sasha Levin]

From: chenzefeng <chenzefeng2@huawei.com>

[ Upstream commit c5e5c48c16422521d363c33cfb0dcf58f88c119b ]

The function free_module in file kernel/module.c as follow:

void free_module(struct module *mod) {
	......
	module_arch_cleanup(mod);
	......
	module_arch_freeing_init(mod);
	......
}

Both module_arch_cleanup and module_arch_freeing_init function
would free the mod->arch.init_unw_table, which cause double free.

Here, set mod->arch.init_unw_table = NULL after remove the unwind
table to avoid double free.

Signed-off-by: chenzefeng <chenzefeng2@huawei.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/ia64/kernel/module.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/ia64/kernel/module.c b/arch/ia64/kernel/module.c
index 36b2c94a8eb5d..14c7184daaf64 100644
--- a/arch/ia64/kernel/module.c
+++ b/arch/ia64/kernel/module.c
@@ -912,8 +912,12 @@ module_finalize (const Elf_Ehdr *hdr, const Elf_Shdr *sechdrs, struct module *mo
 void
 module_arch_cleanup (struct module *mod)
 {
-	if (mod->arch.init_unw_table)
+	if (mod->arch.init_unw_table) {
 		unw_remove_unwind_table(mod->arch.init_unw_table);
-	if (mod->arch.core_unw_table)
+		mod->arch.init_unw_table = NULL;
+	}
+	if (mod->arch.core_unw_table) {
 		unw_remove_unwind_table(mod->arch.core_unw_table);
+		mod->arch.core_unw_table = NULL;
+	}
 }
-- 
2.20.1

[PATCH AUTOSEL 4.4 16/44] ia64:unwind: fix double free for mod->arch.init_unw_table

[Sasha Levin]

From: chenzefeng <chenzefeng2@huawei.com>

[ Upstream commit c5e5c48c16422521d363c33cfb0dcf58f88c119b ]

The function free_module in file kernel/module.c as follow:

void free_module(struct module *mod) {
	......
	module_arch_cleanup(mod);
	......
	module_arch_freeing_init(mod);
	......
}

Both module_arch_cleanup and module_arch_freeing_init function
would free the mod->arch.init_unw_table, which cause double free.

Here, set mod->arch.init_unw_table = NULL after remove the unwind
table to avoid double free.

Signed-off-by: chenzefeng <chenzefeng2@huawei.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/ia64/kernel/module.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/ia64/kernel/module.c b/arch/ia64/kernel/module.c
index 36b2c94a8eb5d..14c7184daaf64 100644
--- a/arch/ia64/kernel/module.c
+++ b/arch/ia64/kernel/module.c
@@ -912,8 +912,12 @@ module_finalize (const Elf_Ehdr *hdr, const Elf_Shdr *sechdrs, struct module *mo
 void
 module_arch_cleanup (struct module *mod)
 {
-	if (mod->arch.init_unw_table)
+	if (mod->arch.init_unw_table) {
 		unw_remove_unwind_table(mod->arch.init_unw_table);
-	if (mod->arch.core_unw_table)
+		mod->arch.init_unw_table = NULL;
+	}
+	if (mod->arch.core_unw_table) {
 		unw_remove_unwind_table(mod->arch.core_unw_table);
+		mod->arch.core_unw_table = NULL;
+	}
 }
-- 
2.20.1

[PATCH AUTOSEL 4.4 17/44] md: don't call spare_active in md_reap_sync_thread if all member devices can't work

[Sasha Levin]

From: Guoqing Jiang <jgq516@gmail.com>

[ Upstream commit 0d8ed0e9bf9643f27f4816dca61081784dedb38d ]

When add one disk to array, the md_reap_sync_thread is responsible
to activate the spare and set In_sync flag for the new member in
spare_active().

But if raid1 has one member disk A, and disk B is added to the array.
Then we offline A before all the datas are synchronized from A to B,
obviously B doesn't have the latest data as A, but B is still marked
with In_sync flag.

So let's not call spare_active under the condition, otherwise B is
still showed with 'U' state which is not correct.

Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/md/md.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/md/md.c b/drivers/md/md.c
index 067af77bb729a..d1b09657c1939 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -8445,7 +8445,8 @@ void md_reap_sync_thread(struct mddev *mddev)
 	/* resync has finished, collect result */
 	md_unregister_thread(&mddev->sync_thread);
 	if (!test_bit(MD_RECOVERY_INTR, &mddev->recovery) &&
-	    !test_bit(MD_RECOVERY_REQUESTED, &mddev->recovery)) {
+	    !test_bit(MD_RECOVERY_REQUESTED, &mddev->recovery) &&
+	    mddev->degraded != mddev->raid_disks) {
 		/* success...*/
 		/* activate any spares */
 		if (mddev->pers->spare_active(mddev)) {
-- 
2.20.1

[PATCH AUTOSEL 4.4 18/44] md: don't set In_sync if array is frozen

[Sasha Levin]

From: Guoqing Jiang <jgq516@gmail.com>

[ Upstream commit 062f5b2ae12a153644c765e7ba3b0f825427be1d ]

When a disk is added to array, the following path is called in mdadm.

Manage_subdevs -> sysfs_freeze_array
               -> Manage_add
               -> sysfs_set_str(&info, NULL, "sync_action","idle")

Then from kernel side, Manage_add invokes the path (add_new_disk ->
validate_super = super_1_validate) to set In_sync flag.

Since In_sync means "device is in_sync with rest of array", and the new
added disk need to resync thread to help the synchronization of data.
And md_reap_sync_thread would call spare_active to set In_sync for the
new added disk finally. So don't set In_sync if array is in frozen.

Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/md/md.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/md/md.c b/drivers/md/md.c
index d1b09657c1939..d59d79b77fd69 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -1667,8 +1667,15 @@ static int super_1_validate(struct mddev *mddev, struct md_rdev *rdev)
 				if (!(le32_to_cpu(sb->feature_map) &
 				      MD_FEATURE_RECOVERY_BITMAP))
 					rdev->saved_raid_disk = -1;
-			} else
-				set_bit(In_sync, &rdev->flags);
+			} else {
+				/*
+				 * If the array is FROZEN, then the device can't
+				 * be in_sync with rest of array.
+				 */
+				if (!test_bit(MD_RECOVERY_FROZEN,
+					      &mddev->recovery))
+					set_bit(In_sync, &rdev->flags);
+			}
 			rdev->raid_disk = role;
 			break;
 		}
-- 
2.20.1

[PATCH AUTOSEL 4.4 19/44] efi: cper: print AER info of PCIe fatal error

[Sasha Levin]

From: Xiaofei Tan <tanxiaofei@huawei.com>

[ Upstream commit b194a77fcc4001dc40aecdd15d249648e8a436d1 ]

AER info of PCIe fatal error is not printed in the current driver.
Because APEI driver will panic directly for fatal error, and can't
run to the place of printing AER info.

An example log is as following:
{763}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 11
{763}[Hardware Error]: event severity: fatal
{763}[Hardware Error]:  Error 0, type: fatal
{763}[Hardware Error]:   section_type: PCIe error
{763}[Hardware Error]:   port_type: 0, PCIe end point
{763}[Hardware Error]:   version: 4.0
{763}[Hardware Error]:   command: 0x0000, status: 0x0010
{763}[Hardware Error]:   device_id: 0000:82:00.0
{763}[Hardware Error]:   slot: 0
{763}[Hardware Error]:   secondary_bus: 0x00
{763}[Hardware Error]:   vendor_id: 0x8086, device_id: 0x10fb
{763}[Hardware Error]:   class_code: 000002
Kernel panic - not syncing: Fatal hardware error!

This issue was imported by the patch, '37448adfc7ce ("aerdrv: Move
cper_print_aer() call out of interrupt context")'. To fix this issue,
this patch adds print of AER info in cper_print_pcie() for fatal error.

Here is the example log after this patch applied:
{24}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 10
{24}[Hardware Error]: event severity: fatal
{24}[Hardware Error]:  Error 0, type: fatal
{24}[Hardware Error]:   section_type: PCIe error
{24}[Hardware Error]:   port_type: 0, PCIe end point
{24}[Hardware Error]:   version: 4.0
{24}[Hardware Error]:   command: 0x0546, status: 0x4010
{24}[Hardware Error]:   device_id: 0000:01:00.0
{24}[Hardware Error]:   slot: 0
{24}[Hardware Error]:   secondary_bus: 0x00
{24}[Hardware Error]:   vendor_id: 0x15b3, device_id: 0x1019
{24}[Hardware Error]:   class_code: 000002
{24}[Hardware Error]:   aer_uncor_status: 0x00040000, aer_uncor_mask: 0x00000000
{24}[Hardware Error]:   aer_uncor_severity: 0x00062010
{24}[Hardware Error]:   TLP Header: 000000c0 01010000 00000001 00000000
Kernel panic - not syncing: Fatal hardware error!

Fixes: 37448adfc7ce ("aerdrv: Move cper_print_aer() call out of interrupt context")
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Reviewed-by: James Morse <james.morse@arm.com>
[ardb: put parens around terms of && operator]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/firmware/efi/cper.c | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/drivers/firmware/efi/cper.c b/drivers/firmware/efi/cper.c
index d425374254384..f40f7df4b7344 100644
--- a/drivers/firmware/efi/cper.c
+++ b/drivers/firmware/efi/cper.c
@@ -384,6 +384,21 @@ static void cper_print_pcie(const char *pfx, const struct cper_sec_pcie *pcie,
 		printk(
 	"%s""bridge: secondary_status: 0x%04x, control: 0x%04x\n",
 	pfx, pcie->bridge.secondary_status, pcie->bridge.control);
+
+	/* Fatal errors call __ghes_panic() before AER handler prints this */
+	if ((pcie->validation_bits & CPER_PCIE_VALID_AER_INFO) &&
+	    (gdata->error_severity & CPER_SEV_FATAL)) {
+		struct aer_capability_regs *aer;
+
+		aer = (struct aer_capability_regs *)pcie->aer_info;
+		printk("%saer_uncor_status: 0x%08x, aer_uncor_mask: 0x%08x\n",
+		       pfx, aer->uncor_status, aer->uncor_mask);
+		printk("%saer_uncor_severity: 0x%08x\n",
+		       pfx, aer->uncor_severity);
+		printk("%sTLP Header: %08x %08x %08x %08x\n", pfx,
+		       aer->header_log.dw0, aer->header_log.dw1,
+		       aer->header_log.dw2, aer->header_log.dw3);
+	}
 }
 
 static void cper_estatus_print_section(
-- 
2.20.1

[PATCH AUTOSEL 4.4 20/44] media: gspca: zero usb_buf on error

[Sasha Levin]

From: Hans Verkuil <hverkuil-cisco@xs4all.nl>

[ Upstream commit 4843a543fad3bf8221cf14e5d5f32d15cee89e84 ]

If reg_r() fails, then gspca_dev->usb_buf was left uninitialized,
and some drivers used the contents of that buffer in logic.

This caused several syzbot errors:

https://syzkaller.appspot.com/bug?extid=397fd082ce5143e2f67d
https://syzkaller.appspot.com/bug?extid=1a35278dd0ebfb3a038a
https://syzkaller.appspot.com/bug?extid=06ddf1788cfd048c5e82

I analyzed the gspca drivers and zeroed the buffer where needed.

Reported-and-tested-by: syzbot+1a35278dd0ebfb3a038a@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+397fd082ce5143e2f67d@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+06ddf1788cfd048c5e82@syzkaller.appspotmail.com

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/gspca/konica.c   |  5 +++++
 drivers/media/usb/gspca/nw80x.c    |  5 +++++
 drivers/media/usb/gspca/ov519.c    | 10 ++++++++++
 drivers/media/usb/gspca/ov534.c    |  5 +++++
 drivers/media/usb/gspca/ov534_9.c  |  1 +
 drivers/media/usb/gspca/se401.c    |  5 +++++
 drivers/media/usb/gspca/sn9c20x.c  |  5 +++++
 drivers/media/usb/gspca/sonixb.c   |  5 +++++
 drivers/media/usb/gspca/sonixj.c   |  5 +++++
 drivers/media/usb/gspca/spca1528.c |  5 +++++
 drivers/media/usb/gspca/sq930x.c   |  5 +++++
 drivers/media/usb/gspca/sunplus.c  |  5 +++++
 drivers/media/usb/gspca/vc032x.c   |  5 +++++
 drivers/media/usb/gspca/w996Xcf.c  |  5 +++++
 14 files changed, 71 insertions(+)

diff --git a/drivers/media/usb/gspca/konica.c b/drivers/media/usb/gspca/konica.c
index 0f6d57fbf91b7..624b4d24716dd 100644
--- a/drivers/media/usb/gspca/konica.c
+++ b/drivers/media/usb/gspca/konica.c
@@ -127,6 +127,11 @@ static void reg_r(struct gspca_dev *gspca_dev, u16 value, u16 index)
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, 2);
 	}
 }
 
diff --git a/drivers/media/usb/gspca/nw80x.c b/drivers/media/usb/gspca/nw80x.c
index 599f755e75b86..7ebeee98dc1bb 100644
--- a/drivers/media/usb/gspca/nw80x.c
+++ b/drivers/media/usb/gspca/nw80x.c
@@ -1584,6 +1584,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 		return;
 	}
 	if (len == 1)
diff --git a/drivers/media/usb/gspca/ov519.c b/drivers/media/usb/gspca/ov519.c
index c95f32a0c02b4..c7aafdbb57384 100644
--- a/drivers/media/usb/gspca/ov519.c
+++ b/drivers/media/usb/gspca/ov519.c
@@ -2116,6 +2116,11 @@ static int reg_r(struct sd *sd, u16 index)
 	} else {
 		PERR("reg_r %02x failed %d\n", index, ret);
 		sd->gspca_dev.usb_err = ret;
+		/*
+		 * Make sure the result is zeroed to avoid uninitialized
+		 * values.
+		 */
+		gspca_dev->usb_buf[0] = 0;
 	}
 
 	return ret;
@@ -2142,6 +2147,11 @@ static int reg_r8(struct sd *sd,
 	} else {
 		PERR("reg_r8 %02x failed %d\n", index, ret);
 		sd->gspca_dev.usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, 8);
 	}
 
 	return ret;
diff --git a/drivers/media/usb/gspca/ov534.c b/drivers/media/usb/gspca/ov534.c
index bfff1d1c70ab0..466f984312ddb 100644
--- a/drivers/media/usb/gspca/ov534.c
+++ b/drivers/media/usb/gspca/ov534.c
@@ -644,6 +644,11 @@ static u8 ov534_reg_read(struct gspca_dev *gspca_dev, u16 reg)
 	if (ret < 0) {
 		pr_err("read failed %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the result is zeroed to avoid uninitialized
+		 * values.
+		 */
+		gspca_dev->usb_buf[0] = 0;
 	}
 	return gspca_dev->usb_buf[0];
 }
diff --git a/drivers/media/usb/gspca/ov534_9.c b/drivers/media/usb/gspca/ov534_9.c
index 47085cf2d7236..f2dca06069355 100644
--- a/drivers/media/usb/gspca/ov534_9.c
+++ b/drivers/media/usb/gspca/ov534_9.c
@@ -1157,6 +1157,7 @@ static u8 reg_r(struct gspca_dev *gspca_dev, u16 reg)
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		return 0;
 	}
 	return gspca_dev->usb_buf[0];
 }
diff --git a/drivers/media/usb/gspca/se401.c b/drivers/media/usb/gspca/se401.c
index 5102cea504710..6adbb0eca71fe 100644
--- a/drivers/media/usb/gspca/se401.c
+++ b/drivers/media/usb/gspca/se401.c
@@ -115,6 +115,11 @@ static void se401_read_req(struct gspca_dev *gspca_dev, u16 req, int silent)
 			pr_err("read req failed req %#04x error %d\n",
 			       req, err);
 		gspca_dev->usb_err = err;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, READ_REQ_SIZE);
 	}
 }
 
diff --git a/drivers/media/usb/gspca/sn9c20x.c b/drivers/media/usb/gspca/sn9c20x.c
index d0ee899584a9f..e5bd1e84fd875 100644
--- a/drivers/media/usb/gspca/sn9c20x.c
+++ b/drivers/media/usb/gspca/sn9c20x.c
@@ -924,6 +924,11 @@ static void reg_r(struct gspca_dev *gspca_dev, u16 reg, u16 length)
 	if (unlikely(result < 0 || result != length)) {
 		pr_err("Read register %02x failed %d\n", reg, result);
 		gspca_dev->usb_err = result;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 
diff --git a/drivers/media/usb/gspca/sonixb.c b/drivers/media/usb/gspca/sonixb.c
index 6696b2ec34e96..83e98b85ab6a1 100644
--- a/drivers/media/usb/gspca/sonixb.c
+++ b/drivers/media/usb/gspca/sonixb.c
@@ -466,6 +466,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 		dev_err(gspca_dev->v4l2_dev.dev,
 			"Error reading register %02x: %d\n", value, res);
 		gspca_dev->usb_err = res;
+		/*
+		 * Make sure the result is zeroed to avoid uninitialized
+		 * values.
+		 */
+		gspca_dev->usb_buf[0] = 0;
 	}
 }
 
diff --git a/drivers/media/usb/gspca/sonixj.c b/drivers/media/usb/gspca/sonixj.c
index fd1c8706d86a8..67e23557a1a94 100644
--- a/drivers/media/usb/gspca/sonixj.c
+++ b/drivers/media/usb/gspca/sonixj.c
@@ -1175,6 +1175,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 
diff --git a/drivers/media/usb/gspca/spca1528.c b/drivers/media/usb/gspca/spca1528.c
index f38fd8949609f..ee93bd443df5d 100644
--- a/drivers/media/usb/gspca/spca1528.c
+++ b/drivers/media/usb/gspca/spca1528.c
@@ -84,6 +84,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 
diff --git a/drivers/media/usb/gspca/sq930x.c b/drivers/media/usb/gspca/sq930x.c
index e274cf19a3ea2..b236e9dcd4685 100644
--- a/drivers/media/usb/gspca/sq930x.c
+++ b/drivers/media/usb/gspca/sq930x.c
@@ -438,6 +438,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r %04x failed %d\n", value, ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 
diff --git a/drivers/media/usb/gspca/sunplus.c b/drivers/media/usb/gspca/sunplus.c
index 46c9f2229a186..cc3e1478c5a09 100644
--- a/drivers/media/usb/gspca/sunplus.c
+++ b/drivers/media/usb/gspca/sunplus.c
@@ -268,6 +268,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 
diff --git a/drivers/media/usb/gspca/vc032x.c b/drivers/media/usb/gspca/vc032x.c
index b4efb2fb36fa3..5032b9d7d9bb2 100644
--- a/drivers/media/usb/gspca/vc032x.c
+++ b/drivers/media/usb/gspca/vc032x.c
@@ -2919,6 +2919,11 @@ static void reg_r_i(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 static void reg_r(struct gspca_dev *gspca_dev,
diff --git a/drivers/media/usb/gspca/w996Xcf.c b/drivers/media/usb/gspca/w996Xcf.c
index fb9fe2ef3a6f6..a74ac595656f7 100644
--- a/drivers/media/usb/gspca/w996Xcf.c
+++ b/drivers/media/usb/gspca/w996Xcf.c
@@ -139,6 +139,11 @@ static int w9968cf_read_sb(struct sd *sd)
 	} else {
 		pr_err("Read SB reg [01] failed\n");
 		sd->gspca_dev.usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(sd->gspca_dev.usb_buf, 0, 2);
 	}
 
 	udelay(W9968CF_I2C_BUS_DELAY);
-- 
2.20.1

[PATCH AUTOSEL 4.4 21/44] dmaengine: iop-adma: use correct printk format strings

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit 00c9755524fbaa28117be774d7c92fddb5ca02f3 ]

When compile-testing on other architectures, we get lots of warnings
about incorrect format strings, like:

   drivers/dma/iop-adma.c: In function 'iop_adma_alloc_slots':
   drivers/dma/iop-adma.c:307:6: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]

   drivers/dma/iop-adma.c: In function 'iop_adma_prep_dma_memcpy':
>> drivers/dma/iop-adma.c:518:40: warning: format '%u' expects argument of type 'unsigned int', but argument 5 has type 'size_t {aka long unsigned int}' [-Wformat=]

Use %zu for printing size_t as required, and cast the dma_addr_t
arguments to 'u64' for printing with %llx. Ideally this should use
the %pad format string, but that requires an lvalue argument that
doesn't work here.

Link: https://lore.kernel.org/r/20190809163334.489360-3-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/dma/iop-adma.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/drivers/dma/iop-adma.c b/drivers/dma/iop-adma.c
index e4f43125e0fbb..a390415c97a86 100644
--- a/drivers/dma/iop-adma.c
+++ b/drivers/dma/iop-adma.c
@@ -126,9 +126,9 @@ static void __iop_adma_slot_cleanup(struct iop_adma_chan *iop_chan)
 	list_for_each_entry_safe(iter, _iter, &iop_chan->chain,
 					chain_node) {
 		pr_debug("\tcookie: %d slot: %d busy: %d "
-			"this_desc: %#x next_desc: %#x ack: %d\n",
+			"this_desc: %#x next_desc: %#llx ack: %d\n",
 			iter->async_tx.cookie, iter->idx, busy,
-			iter->async_tx.phys, iop_desc_get_next_desc(iter),
+			iter->async_tx.phys, (u64)iop_desc_get_next_desc(iter),
 			async_tx_test_ack(&iter->async_tx));
 		prefetch(_iter);
 		prefetch(&_iter->async_tx);
@@ -316,9 +316,9 @@ iop_adma_alloc_slots(struct iop_adma_chan *iop_chan, int num_slots,
 				int i;
 				dev_dbg(iop_chan->device->common.dev,
 					"allocated slot: %d "
-					"(desc %p phys: %#x) slots_per_op %d\n",
+					"(desc %p phys: %#llx) slots_per_op %d\n",
 					iter->idx, iter->hw_desc,
-					iter->async_tx.phys, slots_per_op);
+					(u64)iter->async_tx.phys, slots_per_op);
 
 				/* pre-ack all but the last descriptor */
 				if (num_slots != slots_per_op)
@@ -526,7 +526,7 @@ iop_adma_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dma_dest,
 		return NULL;
 	BUG_ON(len > IOP_ADMA_MAX_BYTE_COUNT);
 
-	dev_dbg(iop_chan->device->common.dev, "%s len: %u\n",
+	dev_dbg(iop_chan->device->common.dev, "%s len: %zu\n",
 		__func__, len);
 
 	spin_lock_bh(&iop_chan->lock);
@@ -559,7 +559,7 @@ iop_adma_prep_dma_xor(struct dma_chan *chan, dma_addr_t dma_dest,
 	BUG_ON(len > IOP_ADMA_XOR_MAX_BYTE_COUNT);
 
 	dev_dbg(iop_chan->device->common.dev,
-		"%s src_cnt: %d len: %u flags: %lx\n",
+		"%s src_cnt: %d len: %zu flags: %lx\n",
 		__func__, src_cnt, len, flags);
 
 	spin_lock_bh(&iop_chan->lock);
@@ -592,7 +592,7 @@ iop_adma_prep_dma_xor_val(struct dma_chan *chan, dma_addr_t *dma_src,
 	if (unlikely(!len))
 		return NULL;
 
-	dev_dbg(iop_chan->device->common.dev, "%s src_cnt: %d len: %u\n",
+	dev_dbg(iop_chan->device->common.dev, "%s src_cnt: %d len: %zu\n",
 		__func__, src_cnt, len);
 
 	spin_lock_bh(&iop_chan->lock);
@@ -630,7 +630,7 @@ iop_adma_prep_dma_pq(struct dma_chan *chan, dma_addr_t *dst, dma_addr_t *src,
 	BUG_ON(len > IOP_ADMA_XOR_MAX_BYTE_COUNT);
 
 	dev_dbg(iop_chan->device->common.dev,
-		"%s src_cnt: %d len: %u flags: %lx\n",
+		"%s src_cnt: %d len: %zu flags: %lx\n",
 		__func__, src_cnt, len, flags);
 
 	if (dmaf_p_disabled_continue(flags))
@@ -693,7 +693,7 @@ iop_adma_prep_dma_pq_val(struct dma_chan *chan, dma_addr_t *pq, dma_addr_t *src,
 		return NULL;
 	BUG_ON(len > IOP_ADMA_XOR_MAX_BYTE_COUNT);
 
-	dev_dbg(iop_chan->device->common.dev, "%s src_cnt: %d len: %u\n",
+	dev_dbg(iop_chan->device->common.dev, "%s src_cnt: %d len: %zu\n",
 		__func__, src_cnt, len);
 
 	spin_lock_bh(&iop_chan->lock);
-- 
2.20.1

[PATCH AUTOSEL 4.4 22/44] media: omap3isp: Don't set streaming state on random subdevs

[Sasha Levin]

From: Sakari Ailus <sakari.ailus@linux.intel.com>

[ Upstream commit 7ef57be07ac146e70535747797ef4aee0f06e9f9 ]

The streaming state should be set to the first upstream sub-device only,
not everywhere, for a sub-device driver itself knows how to best control
the streaming state of its own upstream sub-devices.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/omap3isp/isp.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/media/platform/omap3isp/isp.c b/drivers/media/platform/omap3isp/isp.c
index 136ea1848701d..f41e0d08de93e 100644
--- a/drivers/media/platform/omap3isp/isp.c
+++ b/drivers/media/platform/omap3isp/isp.c
@@ -917,6 +917,10 @@ static int isp_pipeline_enable(struct isp_pipeline *pipe,
 					s_stream, mode);
 			pipe->do_propagation = true;
 		}
+
+		/* Stop at the first external sub-device. */
+		if (subdev->dev != isp->dev)
+			break;
 	}
 
 	return 0;
@@ -1031,6 +1035,10 @@ static int isp_pipeline_disable(struct isp_pipeline *pipe)
 				isp->crashed |= 1U << subdev->entity.id;
 			failure = -ETIMEDOUT;
 		}
+
+		/* Stop at the first external sub-device. */
+		if (subdev->dev != isp->dev)
+			break;
 	}
 
 	return failure;
-- 
2.20.1

[PATCH AUTOSEL 4.4 23/44] net: lpc-enet: fix printk format strings

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit de6f97b2bace0e2eb6c3a86e124d1e652a587b56 ]

compile-testing this driver on other architectures showed
multiple warnings:

  drivers/net/ethernet/nxp/lpc_eth.c: In function 'lpc_eth_drv_probe':
  drivers/net/ethernet/nxp/lpc_eth.c:1337:19: warning: format '%d' expects argument of type 'int', but argument 4 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]

  drivers/net/ethernet/nxp/lpc_eth.c:1342:19: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]

Use format strings that work on all architectures.

Link: https://lore.kernel.org/r/20190809144043.476786-10-arnd@arndb.de
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/nxp/lpc_eth.c | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/nxp/lpc_eth.c b/drivers/net/ethernet/nxp/lpc_eth.c
index 057665180f13f..ba14bad81a21f 100644
--- a/drivers/net/ethernet/nxp/lpc_eth.c
+++ b/drivers/net/ethernet/nxp/lpc_eth.c
@@ -1417,13 +1417,14 @@ static int lpc_eth_drv_probe(struct platform_device *pdev)
 	pldat->dma_buff_base_p = dma_handle;
 
 	netdev_dbg(ndev, "IO address space     :%pR\n", res);
-	netdev_dbg(ndev, "IO address size      :%d\n", resource_size(res));
+	netdev_dbg(ndev, "IO address size      :%zd\n",
+			(size_t)resource_size(res));
 	netdev_dbg(ndev, "IO address (mapped)  :0x%p\n",
 			pldat->net_base);
 	netdev_dbg(ndev, "IRQ number           :%d\n", ndev->irq);
-	netdev_dbg(ndev, "DMA buffer size      :%d\n", pldat->dma_buff_size);
-	netdev_dbg(ndev, "DMA buffer P address :0x%08x\n",
-			pldat->dma_buff_base_p);
+	netdev_dbg(ndev, "DMA buffer size      :%zd\n", pldat->dma_buff_size);
+	netdev_dbg(ndev, "DMA buffer P address :%pad\n",
+			&pldat->dma_buff_base_p);
 	netdev_dbg(ndev, "DMA buffer V address :0x%p\n",
 			pldat->dma_buff_base_v);
 
@@ -1470,8 +1471,8 @@ static int lpc_eth_drv_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_out_unregister_netdev;
 
-	netdev_info(ndev, "LPC mac at 0x%08x irq %d\n",
-	       res->start, ndev->irq);
+	netdev_info(ndev, "LPC mac at 0x%08lx irq %d\n",
+	       (unsigned long)res->start, ndev->irq);
 
 	phydev = pldat->phy_dev;
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 24/44] media: radio/si470x: kill urb on error

[Sasha Levin]

From: Hans Verkuil <hverkuil-cisco@xs4all.nl>

[ Upstream commit 0d616f2a3fdbf1304db44d451d9f07008556923b ]

In the probe() function radio->int_in_urb was not killed if an
error occurred in the probe sequence. It was also missing in
the disconnect.

This caused this syzbot issue:

https://syzkaller.appspot.com/bug?extid=2d4fc2a0c45ad8da7e99

Reported-and-tested-by: syzbot+2d4fc2a0c45ad8da7e99@syzkaller.appspotmail.com

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/radio/si470x/radio-si470x-usb.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/media/radio/si470x/radio-si470x-usb.c b/drivers/media/radio/si470x/radio-si470x-usb.c
index 091d793f65836..c9347d5aac04f 100644
--- a/drivers/media/radio/si470x/radio-si470x-usb.c
+++ b/drivers/media/radio/si470x/radio-si470x-usb.c
@@ -743,7 +743,7 @@ static int si470x_usb_driver_probe(struct usb_interface *intf,
 	/* start radio */
 	retval = si470x_start_usb(radio);
 	if (retval < 0)
-		goto err_all;
+		goto err_buf;
 
 	/* set initial frequency */
 	si470x_set_freq(radio, 87.5 * FREQ_MUL); /* available in all regions */
@@ -758,6 +758,8 @@ static int si470x_usb_driver_probe(struct usb_interface *intf,
 
 	return 0;
 err_all:
+	usb_kill_urb(radio->int_in_urb);
+err_buf:
 	kfree(radio->buffer);
 err_ctrl:
 	v4l2_ctrl_handler_free(&radio->hdl);
@@ -831,6 +833,7 @@ static void si470x_usb_driver_disconnect(struct usb_interface *intf)
 	mutex_lock(&radio->lock);
 	v4l2_device_disconnect(&radio->v4l2_dev);
 	video_unregister_device(&radio->videodev);
+	usb_kill_urb(radio->int_in_urb);
 	usb_set_intfdata(intf, NULL);
 	mutex_unlock(&radio->lock);
 	v4l2_device_put(&radio->v4l2_dev);
-- 
2.20.1

[PATCH AUTOSEL 4.4 25/44] media: hdpvr: add terminating 0 at end of string

[Sasha Levin]

From: Hans Verkuil <hverkuil-cisco@xs4all.nl>

[ Upstream commit 8b8900b729e4f31f12ac1127bde137c775c327e6 ]

dev->usbc_buf was passed as argument for %s, but it was not safeguarded
by a terminating 0.

This caused this syzbot issue:

https://syzkaller.appspot.com/bug?extid=79d18aac4bf1770dd050

Reported-and-tested-by: syzbot+79d18aac4bf1770dd050@syzkaller.appspotmail.com

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/hdpvr/hdpvr-core.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/media/usb/hdpvr/hdpvr-core.c b/drivers/media/usb/hdpvr/hdpvr-core.c
index 924517b09fc9f..7b5c493f02b0a 100644
--- a/drivers/media/usb/hdpvr/hdpvr-core.c
+++ b/drivers/media/usb/hdpvr/hdpvr-core.c
@@ -143,6 +143,7 @@ static int device_authorization(struct hdpvr_device *dev)
 
 	dev->fw_ver = dev->usbc_buf[1];
 
+	dev->usbc_buf[46] = '\0';
 	v4l2_info(&dev->v4l2_dev, "firmware version 0x%x dated %s\n",
 			  dev->fw_ver, &dev->usbc_buf[2]);
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 26/44] media: saa7146: add cleanup in hexium_attach()

[Sasha Levin]

From: Wenwen Wang <wenwen@cs.uga.edu>

[ Upstream commit 42e64117d3b4a759013f77bbcf25ab6700e55de7 ]

If saa7146_register_device() fails, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, perform necessary cleanup work
before returning the error.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/pci/saa7146/hexium_gemini.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/media/pci/saa7146/hexium_gemini.c b/drivers/media/pci/saa7146/hexium_gemini.c
index d4b3ce8282856..343cd75fcd8d1 100644
--- a/drivers/media/pci/saa7146/hexium_gemini.c
+++ b/drivers/media/pci/saa7146/hexium_gemini.c
@@ -304,6 +304,9 @@ static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_d
 	ret = saa7146_register_device(&hexium->video_dev, dev, "hexium gemini", VFL_TYPE_GRABBER);
 	if (ret < 0) {
 		pr_err("cannot register capture v4l2 device. skipping.\n");
+		saa7146_vv_release(dev);
+		i2c_del_adapter(&hexium->i2c_adapter);
+		kfree(hexium);
 		return ret;
 	}
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 27/44] media: cpia2_usb: fix memory leaks

[Sasha Levin]

From: Wenwen Wang <wenwen@cs.uga.edu>

[ Upstream commit 1c770f0f52dca1a2323c594f01f5ec6f1dddc97f ]

In submit_urbs(), 'cam->sbuf[i].data' is allocated through kmalloc_array().
However, it is not deallocated if the following allocation for urbs fails.
To fix this issue, free 'cam->sbuf[i].data' if usb_alloc_urb() fails.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/cpia2/cpia2_usb.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/media/usb/cpia2/cpia2_usb.c b/drivers/media/usb/cpia2/cpia2_usb.c
index 41ea00ac3a873..76b9cb940b871 100644
--- a/drivers/media/usb/cpia2/cpia2_usb.c
+++ b/drivers/media/usb/cpia2/cpia2_usb.c
@@ -665,6 +665,10 @@ static int submit_urbs(struct camera_data *cam)
 			ERR("%s: usb_alloc_urb error!\n", __func__);
 			for (j = 0; j < i; j++)
 				usb_free_urb(cam->sbuf[j].urb);
+			for (j = 0; j < NUM_SBUF; j++) {
+				kfree(cam->sbuf[j].data);
+				cam->sbuf[j].data = NULL;
+			}
 			return -ENOMEM;
 		}
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 28/44] media: saa7134: fix terminology around saa7134_i2c_eeprom_md7134_gate()

[Sasha Levin]

From: "Maciej S. Szmigiero" <mail@maciej.szmigiero.name>

[ Upstream commit 9d802222a3405599d6e1984d9324cddf592ea1f4 ]

saa7134_i2c_eeprom_md7134_gate() function and the associated comment uses
an inverted i2c gate open / closed terminology.
Let's fix this.

Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix alignment checkpatch warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/pci/saa7134/saa7134-i2c.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/drivers/media/pci/saa7134/saa7134-i2c.c b/drivers/media/pci/saa7134/saa7134-i2c.c
index bc957528f69ff..e636fca36e3da 100644
--- a/drivers/media/pci/saa7134/saa7134-i2c.c
+++ b/drivers/media/pci/saa7134/saa7134-i2c.c
@@ -355,7 +355,11 @@ static struct i2c_client saa7134_client_template = {
 
 /* ----------------------------------------------------------- */
 
-/* On Medion 7134 reading EEPROM needs DVB-T demod i2c gate open */
+/*
+ * On Medion 7134 reading the SAA7134 chip config EEPROM needs DVB-T
+ * demod i2c gate closed due to an address clash between this EEPROM
+ * and the demod one.
+ */
 static void saa7134_i2c_eeprom_md7134_gate(struct saa7134_dev *dev)
 {
 	u8 subaddr = 0x7, dmdregval;
@@ -372,14 +376,14 @@ static void saa7134_i2c_eeprom_md7134_gate(struct saa7134_dev *dev)
 
 	ret = i2c_transfer(&dev->i2c_adap, i2cgatemsg_r, 2);
 	if ((ret == 2) && (dmdregval & 0x2)) {
-		pr_debug("%s: DVB-T demod i2c gate was left closed\n",
+		pr_debug("%s: DVB-T demod i2c gate was left open\n",
 			 dev->name);
 
 		data[0] = subaddr;
 		data[1] = (dmdregval & ~0x2);
 		if (i2c_transfer(&dev->i2c_adap, i2cgatemsg_w, 1) != 1)
-			pr_err("%s: EEPROM i2c gate open failure\n",
-			  dev->name);
+			pr_err("%s: EEPROM i2c gate close failure\n",
+			       dev->name);
 	}
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 29/44] media: ov9650: add a sanity check

[Sasha Levin]

From: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

[ Upstream commit 093347abc7a4e0490e3c962ecbde2dc272a8f708 ]

As pointed by cppcheck:

	[drivers/media/i2c/ov9650.c:706]: (error) Shifting by a negative value is undefined behaviour
	[drivers/media/i2c/ov9650.c:707]: (error) Shifting by a negative value is undefined behaviour
	[drivers/media/i2c/ov9650.c:721]: (error) Shifting by a negative value is undefined behaviour

Prevent mangling with gains with invalid values.

As pointed by Sylvester, this should never happen in practice,
as min value of V4L2_CID_GAIN control is 16 (gain is always >= 16
and m is always >= 0), but it is too hard for a static analyzer
to get this, as the logic with validates control min/max is
elsewhere inside V4L2 core.

Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/i2c/ov9650.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/media/i2c/ov9650.c b/drivers/media/i2c/ov9650.c
index 1ee6a5527c384..d11de02ecb63e 100644
--- a/drivers/media/i2c/ov9650.c
+++ b/drivers/media/i2c/ov9650.c
@@ -707,6 +707,11 @@ static int ov965x_set_gain(struct ov965x *ov965x, int auto_gain)
 		for (m = 6; m >= 0; m--)
 			if (gain >= (1 << m) * 16)
 				break;
+
+		/* Sanity check: don't adjust the gain with a negative value */
+		if (m < 0)
+			return -EINVAL;
+
 		rgain = (gain - ((1 << m) * 16)) / (1 << m);
 		rgain |= (((1 << m) - 1) << 4);
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 30/44] ACPI / CPPC: do not require the _PSD method

[Sasha Levin]

From: Al Stone <ahs3@redhat.com>

[ Upstream commit 4c4cdc4c63853fee48c02e25c8605fb65a6c9924 ]

According to the ACPI 6.3 specification, the _PSD method is optional
when using CPPC.  The underlying assumption is that each CPU can change
frequency independently from all other CPUs; _PSD is provided to tell
the OS that some processors can NOT do that.

However, the acpi_get_psd() function returns ENODEV if there is no _PSD
method present, or an ACPI error status if an error occurs when evaluating
_PSD, if present.  This makes _PSD mandatory when using CPPC, in violation
of the specification, and only on Linux.

This has forced some firmware writers to provide a dummy _PSD, even though
it is irrelevant, but only because Linux requires it; other OSPMs follow
the spec.  We really do not want to have OS specific ACPI tables, though.

So, correct acpi_get_psd() so that it does not return an error if there
is no _PSD method present, but does return a failure when the method can
not be executed properly.  This allows _PSD to be optional as it should
be.

Signed-off-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/acpi/cppc_acpi.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/acpi/cppc_acpi.c b/drivers/acpi/cppc_acpi.c
index 0afd1981e350b..43c27c04c40ae 100644
--- a/drivers/acpi/cppc_acpi.c
+++ b/drivers/acpi/cppc_acpi.c
@@ -137,8 +137,10 @@ static int acpi_get_psd(struct cpc_desc *cpc_ptr, acpi_handle handle)
 	union acpi_object  *psd = NULL;
 	struct acpi_psd_package *pdomain;
 
-	status = acpi_evaluate_object_typed(handle, "_PSD", NULL, &buffer,
-			ACPI_TYPE_PACKAGE);
+	status = acpi_evaluate_object_typed(handle, "_PSD", NULL,
+					    &buffer, ACPI_TYPE_PACKAGE);
+	if (status == AE_NOT_FOUND)	/* _PSD is optional */
+		return 0;
 	if (ACPI_FAILURE(status))
 		return -ENODEV;
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 31/44] libtraceevent: Change users plugin directory

[Sasha Levin]

From: Tzvetomir Stoyanov <tstoyanov@vmware.com>

[ Upstream commit e97fd1383cd77c467d2aed7fa4e596789df83977 ]

To be compliant with XDG user directory layout, the user's plugin
directory is changed from ~/.traceevent/plugins to
~/.local/lib/traceevent/plugins/

Suggested-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Patrick McLean <chutzpah@gentoo.org>
Cc: linux-trace-devel@vger.kernel.org
Link: https://lore.kernel.org/linux-trace-devel/20190313144206.41e75cf8@patrickm/
Link: http://lore.kernel.org/linux-trace-devel/20190801074959.22023-4-tz.stoyanov@gmail.com
Link: http://lore.kernel.org/lkml/20190805204355.344622683@goodmis.org
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/lib/traceevent/Makefile       | 6 +++---
 tools/lib/traceevent/event-plugin.c | 2 +-
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/tools/lib/traceevent/Makefile b/tools/lib/traceevent/Makefile
index 7851df1490e0a..cc3315da6dc39 100644
--- a/tools/lib/traceevent/Makefile
+++ b/tools/lib/traceevent/Makefile
@@ -54,15 +54,15 @@ set_plugin_dir := 1
 
 # Set plugin_dir to preffered global plugin location
 # If we install under $HOME directory we go under
-# $(HOME)/.traceevent/plugins
+# $(HOME)/.local/lib/traceevent/plugins
 #
 # We dont set PLUGIN_DIR in case we install under $HOME
 # directory, because by default the code looks under:
-# $(HOME)/.traceevent/plugins by default.
+# $(HOME)/.local/lib/traceevent/plugins by default.
 #
 ifeq ($(plugin_dir),)
 ifeq ($(prefix),$(HOME))
-override plugin_dir = $(HOME)/.traceevent/plugins
+override plugin_dir = $(HOME)/.local/lib/traceevent/plugins
 set_plugin_dir := 0
 else
 override plugin_dir = $(libdir)/traceevent/plugins
diff --git a/tools/lib/traceevent/event-plugin.c b/tools/lib/traceevent/event-plugin.c
index a16756ae35267..5fe7889606a23 100644
--- a/tools/lib/traceevent/event-plugin.c
+++ b/tools/lib/traceevent/event-plugin.c
@@ -30,7 +30,7 @@
 #include "event-parse.h"
 #include "event-utils.h"
 
-#define LOCAL_PLUGIN_DIR ".traceevent/plugins"
+#define LOCAL_PLUGIN_DIR ".local/lib/traceevent/plugins/"
 
 static struct registered_plugin_options {
 	struct registered_plugin_options	*next;
-- 
2.20.1

[PATCH AUTOSEL 4.4 32/44] ACPI: custom_method: fix memory leaks

[Sasha Levin]

From: Wenwen Wang <wenwen@cs.uga.edu>

[ Upstream commit 03d1571d9513369c17e6848476763ebbd10ec2cb ]

In cm_write(), 'buf' is allocated through kzalloc(). In the following
execution, if an error occurs, 'buf' is not deallocated, leading to memory
leaks. To fix this issue, free 'buf' before returning the error.

Fixes: 526b4af47f44 ("ACPI: Split out custom_method functionality into an own driver")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/acpi/custom_method.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/acpi/custom_method.c b/drivers/acpi/custom_method.c
index c68e72414a67a..435bd0ffc8c02 100644
--- a/drivers/acpi/custom_method.c
+++ b/drivers/acpi/custom_method.c
@@ -48,8 +48,10 @@ static ssize_t cm_write(struct file *file, const char __user * user_buf,
 	if ((*ppos > max_size) ||
 	    (*ppos + count > max_size) ||
 	    (*ppos + count < count) ||
-	    (count > uncopied_bytes))
+	    (count > uncopied_bytes)) {
+		kfree(buf);
 		return -EINVAL;
+	}
 
 	if (copy_from_user(buf + (*ppos), user_buf, count)) {
 		kfree(buf);
@@ -69,6 +71,7 @@ static ssize_t cm_write(struct file *file, const char __user * user_buf,
 		add_taint(TAINT_OVERRIDDEN_ACPI_TABLE, LOCKDEP_NOW_UNRELIABLE);
 	}
 
+	kfree(buf);
 	return count;
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 33/44] hwmon: (acpi_power_meter) Change log level for 'unsafe software power cap'

[Sasha Levin]

From: Wang Shenran <shenran268@gmail.com>

[ Upstream commit 6e4d91aa071810deac2cd052161aefb376ecf04e ]

At boot time, the acpi_power_meter driver logs the following error level
message: "Ignoring unsafe software power cap". Having read about it from
a few sources, it seems that the error message can be quite misleading.

While the message can imply that Linux is ignoring the fact that the
system is operating in potentially dangerous conditions, the truth is
the driver found an ACPI_PMC object that supports software power
capping. The driver simply decides not to use it, perhaps because it
doesn't support the object.

The best solution is probably changing the log level from error to warning.
All sources I have found, regarding the error, have downplayed its
significance. There is not much of a reason for it to be on error level,
while causing potential confusions or misinterpretations.

Signed-off-by: Wang Shenran <shenran268@gmail.com>
Link: https://lore.kernel.org/r/20190724080110.6952-1-shenran268@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/hwmon/acpi_power_meter.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/hwmon/acpi_power_meter.c b/drivers/hwmon/acpi_power_meter.c
index 579bdf93be433..e27f7e12c05bb 100644
--- a/drivers/hwmon/acpi_power_meter.c
+++ b/drivers/hwmon/acpi_power_meter.c
@@ -693,8 +693,8 @@ static int setup_attrs(struct acpi_power_meter_resource *resource)
 
 	if (resource->caps.flags & POWER_METER_CAN_CAP) {
 		if (!can_cap_in_hardware()) {
-			dev_err(&resource->acpi_dev->dev,
-				"Ignoring unsafe software power cap!\n");
+			dev_warn(&resource->acpi_dev->dev,
+				 "Ignoring unsafe software power cap!\n");
 			goto skip_unsafe_cap;
 		}
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 34/44] md/raid1: fail run raid1 array when active disk less than one

[Sasha Levin]

From: Yufen Yu <yuyufen@huawei.com>

[ Upstream commit 07f1a6850c5d5a65c917c3165692b5179ac4cb6b ]

When run test case:
  mdadm -CR /dev/md1 -l 1 -n 4 /dev/sd[a-d] --assume-clean --bitmap=internal
  mdadm -S /dev/md1
  mdadm -A /dev/md1 /dev/sd[b-c] --run --force

  mdadm --zero /dev/sda
  mdadm /dev/md1 -a /dev/sda

  echo offline > /sys/block/sdc/device/state
  echo offline > /sys/block/sdb/device/state
  sleep 5
  mdadm -S /dev/md1

  echo running > /sys/block/sdb/device/state
  echo running > /sys/block/sdc/device/state
  mdadm -A /dev/md1 /dev/sd[a-c] --run --force

mdadm run fail with kernel message as follow:
[  172.986064] md: kicking non-fresh sdb from array!
[  173.004210] md: kicking non-fresh sdc from array!
[  173.022383] md/raid1:md1: active with 0 out of 4 mirrors
[  173.022406] md1: failed to create bitmap (-5)

In fact, when active disk in raid1 array less than one, we
need to return fail in raid1_run().

Reviewed-by: NeilBrown <neilb@suse.de>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/md/raid1.c | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)

diff --git a/drivers/md/raid1.c b/drivers/md/raid1.c
index 82e284d2b202b..abb99515068b1 100644
--- a/drivers/md/raid1.c
+++ b/drivers/md/raid1.c
@@ -2958,6 +2958,13 @@ static int run(struct mddev *mddev)
 		    !test_bit(In_sync, &conf->mirrors[i].rdev->flags) ||
 		    test_bit(Faulty, &conf->mirrors[i].rdev->flags))
 			mddev->degraded++;
+	/*
+	 * RAID1 needs at least one disk in active
+	 */
+	if (conf->raid_disks - mddev->degraded < 1) {
+		ret = -EINVAL;
+		goto abort;
+	}
 
 	if (conf->raid_disks - mddev->degraded == 1)
 		mddev->recovery_cp = MaxSector;
@@ -2992,8 +2999,12 @@ static int run(struct mddev *mddev)
 	ret =  md_integrity_register(mddev);
 	if (ret) {
 		md_unregister_thread(&mddev->thread);
-		raid1_free(mddev, conf);
+		goto abort;
 	}
+	return 0;
+
+abort:
+	raid1_free(mddev, conf);
 	return ret;
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 35/44] dmaengine: ti: edma: Do not reset reserved paRAM slots

[Sasha Levin]

From: Peter Ujfalusi <peter.ujfalusi@ti.com>

[ Upstream commit c5dbe60664b3660f5ac5854e21273ea2e7ff698f ]

Skip resetting paRAM slots marked as reserved as they might be used by
other cores.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190823125618.8133-2-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/dma/edma.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/dma/edma.c b/drivers/dma/edma.c
index 85674a8d04368..e508c8c5f3fde 100644
--- a/drivers/dma/edma.c
+++ b/drivers/dma/edma.c
@@ -2218,9 +2218,6 @@ static int edma_probe(struct platform_device *pdev)
 
 	ecc->default_queue = info->default_queue;
 
-	for (i = 0; i < ecc->num_slots; i++)
-		edma_write_slot(ecc, i, &dummy_paramset);
-
 	if (info->rsv) {
 		/* Set the reserved slots in inuse list */
 		rsv_slots = info->rsv->rsv_slots;
@@ -2233,6 +2230,12 @@ static int edma_probe(struct platform_device *pdev)
 		}
 	}
 
+	for (i = 0; i < ecc->num_slots; i++) {
+		/* Reset only unused - not reserved - paRAM slots */
+		if (!test_bit(i, ecc->slot_inuse))
+			edma_write_slot(ecc, i, &dummy_paramset);
+	}
+
 	/* Clear the xbar mapped channels in unused list */
 	xbar_chans = info->xbar_chans;
 	if (xbar_chans) {
-- 
2.20.1

[PATCH AUTOSEL 4.4 36/44] kprobes: Prohibit probing on BUG() and WARN() address

[Sasha Levin]

From: Masami Hiramatsu <mhiramat@kernel.org>

[ Upstream commit e336b4027775cb458dc713745e526fa1a1996b2a ]

Since BUG() and WARN() may use a trap (e.g. UD2 on x86) to
get the address where the BUG() has occurred, kprobes can not
do single-step out-of-line that instruction. So prohibit
probing on such address.

Without this fix, if someone put a kprobe on WARN(), the
kernel will crash with invalid opcode error instead of
outputing warning message, because kernel can not find
correct bug address.

Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naveen N . Rao <naveen.n.rao@linux.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/156750890133.19112.3393666300746167111.stgit@devnote2
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/linux/bug.h | 5 +++++
 kernel/kprobes.c    | 3 ++-
 2 files changed, 7 insertions(+), 1 deletion(-)

diff --git a/include/linux/bug.h b/include/linux/bug.h
index 7f4818673c41f..581a53dfbd310 100644
--- a/include/linux/bug.h
+++ b/include/linux/bug.h
@@ -102,6 +102,11 @@ int is_valid_bugaddr(unsigned long addr);
 
 #else	/* !CONFIG_GENERIC_BUG */
 
+static inline void *find_bug(unsigned long bugaddr)
+{
+	return NULL;
+}
+
 static inline enum bug_trap_type report_bug(unsigned long bug_addr,
 					    struct pt_regs *regs)
 {
diff --git a/kernel/kprobes.c b/kernel/kprobes.c
index a53998cba804c..fdde50d39a46d 100644
--- a/kernel/kprobes.c
+++ b/kernel/kprobes.c
@@ -1454,7 +1454,8 @@ static int check_kprobe_address_safe(struct kprobe *p,
 	/* Ensure it is not in reserved area nor out of text */
 	if (!kernel_text_address((unsigned long) p->addr) ||
 	    within_kprobe_blacklist((unsigned long) p->addr) ||
-	    jump_label_text_reserved(p->addr, p->addr)) {
+	    jump_label_text_reserved(p->addr, p->addr) ||
+	    find_bug((unsigned long)p->addr)) {
 		ret = -EINVAL;
 		goto out;
 	}
-- 
2.20.1

[PATCH AUTOSEL 4.4 37/44] irqchip/gic-v3-its: Fix LPI release for Multi-MSI devices

[Sasha Levin]

From: Marc Zyngier <maz@kernel.org>

[ Upstream commit c9c96e30ecaa0aafa225aa1a5392cb7db17c7a82 ]

When allocating a range of LPIs for a Multi-MSI capable device,
this allocation extended to the closest power of 2.

But on the release path, the interrupts are released one by
one. This results in not releasing the "extra" range, leaking
the its_device. Trying to reprobe the device will then fail.

Fix it by releasing the LPIs the same way we allocate them.

Fixes: 8208d1708b88 ("irqchip/gic-v3-its: Align PCI Multi-MSI allocation on their size")
Reported-by: Jiaxing Luo <luojiaxing@huawei.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/f5e948aa-e32f-3f74-ae30-31fee06c2a74@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/irqchip/irq-gic-v3-its.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)

diff --git a/drivers/irqchip/irq-gic-v3-its.c b/drivers/irqchip/irq-gic-v3-its.c
index 114d5883d4978..cf11d43ce2416 100644
--- a/drivers/irqchip/irq-gic-v3-its.c
+++ b/drivers/irqchip/irq-gic-v3-its.c
@@ -1372,14 +1372,13 @@ static void its_irq_domain_free(struct irq_domain *domain, unsigned int virq,
 	struct its_device *its_dev = irq_data_get_irq_chip_data(d);
 	int i;
 
+	bitmap_release_region(its_dev->event_map.lpi_map,
+			      its_get_event_id(irq_domain_get_irq_data(domain, virq)),
+			      get_count_order(nr_irqs));
+
 	for (i = 0; i < nr_irqs; i++) {
 		struct irq_data *data = irq_domain_get_irq_data(domain,
 								virq + i);
-		u32 event = its_get_event_id(data);
-
-		/* Mark interrupt index as unused */
-		clear_bit(event, its_dev->event_map.lpi_map);
-
 		/* Nuke the entry in the domain */
 		irq_domain_reset_irq_data(data);
 	}
-- 
2.20.1

[PATCH AUTOSEL 4.4 38/44] x86/platform/uv: Fix kmalloc() NULL check routine

[Sasha Levin]

From: Austin Kim <austindh.kim@gmail.com>

[ Upstream commit 864b23f0169d5bff677e8443a7a90dfd6b090afc ]

The result of kmalloc() should have been checked ahead of below statement:

	pqp = (struct bau_pq_entry *)vp;

Move BUG_ON(!vp) before above statement.

Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Hedi Berriche <hedi.berriche@hpe.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <russ.anderson@hpe.com>
Cc: Steve Wahl <steve.wahl@hpe.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: allison@lohutok.net
Cc: andy@infradead.org
Cc: armijn@tjaldur.nl
Cc: bp@alien8.de
Cc: dvhart@infradead.org
Cc: gregkh@linuxfoundation.org
Cc: hpa@zytor.com
Cc: kjlu@umn.edu
Cc: platform-driver-x86@vger.kernel.org
Link: https://lkml.kernel.org/r/20190905232951.GA28779@LGEARND20B15
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/platform/uv/tlb_uv.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/x86/platform/uv/tlb_uv.c b/arch/x86/platform/uv/tlb_uv.c
index 3b6ec42718e46..fd2149e8ca0f7 100644
--- a/arch/x86/platform/uv/tlb_uv.c
+++ b/arch/x86/platform/uv/tlb_uv.c
@@ -1784,9 +1784,9 @@ static void pq_init(int node, int pnode)
 
 	plsize = (DEST_Q_SIZE + 1) * sizeof(struct bau_pq_entry);
 	vp = kmalloc_node(plsize, GFP_KERNEL, node);
-	pqp = (struct bau_pq_entry *)vp;
-	BUG_ON(!pqp);
+	BUG_ON(!vp);
 
+	pqp = (struct bau_pq_entry *)vp;
 	cp = (char *)pqp + 31;
 	pqp = (struct bau_pq_entry *)(((unsigned long)cp >> 5) << 5);
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 39/44] ASoC: dmaengine: Make the pcm->name equal to pcm->id if the name is not set

[Sasha Levin]

From: Peter Ujfalusi <peter.ujfalusi@ti.com>

[ Upstream commit 2ec42f3147e1610716f184b02e65d7f493eed925 ]

Some tools use the snd_pcm_info_get_name() to try to identify PCMs or for
other purposes.

Currently it is left empty with the dmaengine-pcm, in this case copy the
pcm->id string as pcm->name.

For example IGT is using this to find the HDMI PCM for testing audio on it.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Arthur She <arthur.she@linaro.org>
Link: https://lore.kernel.org/r/20190906055524.7393-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/soc-generic-dmaengine-pcm.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/sound/soc/soc-generic-dmaengine-pcm.c b/sound/soc/soc-generic-dmaengine-pcm.c
index 6fd1906af3873..fe65754c2e504 100644
--- a/sound/soc/soc-generic-dmaengine-pcm.c
+++ b/sound/soc/soc-generic-dmaengine-pcm.c
@@ -301,6 +301,12 @@ static int dmaengine_pcm_new(struct snd_soc_pcm_runtime *rtd)
 
 		if (!dmaengine_pcm_can_report_residue(dev, pcm->chan[i]))
 			pcm->flags |= SND_DMAENGINE_PCM_FLAG_NO_RESIDUE;
+
+		if (rtd->pcm->streams[i].pcm->name[0] == '\0') {
+			strncpy(rtd->pcm->streams[i].pcm->name,
+				rtd->pcm->streams[i].pcm->id,
+				sizeof(rtd->pcm->streams[i].pcm->name));
+		}
 	}
 
 	return 0;
-- 
2.20.1

[PATCH AUTOSEL 4.4 40/44] mmc: sdhci: Fix incorrect switch to HS mode

[Sasha Levin]

From: Al Cooper <alcooperx@gmail.com>

[ Upstream commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37 ]

When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.

This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.

The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.

This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.

Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mmc/host/sdhci.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 62d37d2ac557b..1d6dfde1104d1 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -1452,7 +1452,9 @@ void sdhci_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
 		ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
 	else if (timing == MMC_TIMING_UHS_SDR12)
 		ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
-	else if (timing == MMC_TIMING_UHS_SDR25)
+	else if (timing == MMC_TIMING_SD_HS ||
+		 timing == MMC_TIMING_MMC_HS ||
+		 timing == MMC_TIMING_UHS_SDR25)
 		ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
 	else if (timing == MMC_TIMING_UHS_SDR50)
 		ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
-- 
2.20.1

[PATCH AUTOSEL 4.4 41/44] libertas: Add missing sentinel at end of if_usb.c fw_table

[Sasha Levin]

From: Kevin Easton <kevin@guarana.org>

[ Upstream commit 764f3f1ecffc434096e0a2b02f1a6cc964a89df6 ]

This sentinel tells the firmware loading process when to stop.

Reported-and-tested-by: syzbot+98156c174c5a2cad9f8f@syzkaller.appspotmail.com
Signed-off-by: Kevin Easton <kevin@guarana.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/libertas/if_usb.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/libertas/if_usb.c b/drivers/net/wireless/libertas/if_usb.c
index dff08a2896a38..d271eaf1f9499 100644
--- a/drivers/net/wireless/libertas/if_usb.c
+++ b/drivers/net/wireless/libertas/if_usb.c
@@ -49,7 +49,8 @@ static const struct lbs_fw_table fw_table[] = {
 	{ MODEL_8388, "libertas/usb8388_v5.bin", NULL },
 	{ MODEL_8388, "libertas/usb8388.bin", NULL },
 	{ MODEL_8388, "usb8388.bin", NULL },
-	{ MODEL_8682, "libertas/usb8682.bin", NULL }
+	{ MODEL_8682, "libertas/usb8682.bin", NULL },
+	{ 0, NULL, NULL }
 };
 
 static struct usb_device_id if_usb_table[] = {
-- 
2.20.1

[PATCH AUTOSEL 4.4 42/44] media: ttusb-dec: Fix info-leak in ttusb_dec_send_command()

[Sasha Levin]

From: Tomas Bortoli <tomasbortoli@gmail.com>

[ Upstream commit a10feaf8c464c3f9cfdd3a8a7ce17e1c0d498da1 ]

The function at issue does not always initialize each byte allocated
for 'b' and can therefore leak uninitialized memory to a USB device in
the call to usb_bulk_msg()

Use kzalloc() instead of kmalloc()

Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+0522702e9d67142379f1@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/ttusb-dec/ttusb_dec.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/usb/ttusb-dec/ttusb_dec.c b/drivers/media/usb/ttusb-dec/ttusb_dec.c
index a5de46f04247f..f9b5de7ace01c 100644
--- a/drivers/media/usb/ttusb-dec/ttusb_dec.c
+++ b/drivers/media/usb/ttusb-dec/ttusb_dec.c
@@ -272,7 +272,7 @@ static int ttusb_dec_send_command(struct ttusb_dec *dec, const u8 command,
 
 	dprintk("%s\n", __func__);
 
-	b = kmalloc(COMMAND_PACKET_SIZE + 4, GFP_KERNEL);
+	b = kzalloc(COMMAND_PACKET_SIZE + 4, GFP_KERNEL);
 	if (!b)
 		return -ENOMEM;
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 43/44] ALSA: hda/realtek - Blacklist PC beep for Lenovo ThinkCentre M73/93

[Sasha Levin]

From: Takashi Iwai <tiwai@suse.de>

[ Upstream commit 051c78af14fcd74a22b5af45548ad9d588247cc7 ]

Lenovo ThinkCentre M73 and M93 don't seem to have a proper beep
although the driver tries to probe and set up blindly.
Blacklist these machines for suppressing the beep creation.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204635
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/pci/hda/patch_realtek.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index d5ca16048ce0d..55bae9e6de27d 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -977,6 +977,9 @@ static const struct snd_pci_quirk beep_white_list[] = {
 	SND_PCI_QUIRK(0x1043, 0x834a, "EeePC", 1),
 	SND_PCI_QUIRK(0x1458, 0xa002, "GA-MA790X", 1),
 	SND_PCI_QUIRK(0x8086, 0xd613, "Intel", 1),
+	/* blacklist -- no beep available */
+	SND_PCI_QUIRK(0x17aa, 0x309e, "Lenovo ThinkCentre M73", 0),
+	SND_PCI_QUIRK(0x17aa, 0x30a3, "Lenovo ThinkCentre M93", 0),
 	{}
 };
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 44/44] btrfs: extent-tree: Make sure we only allocate extents from block groups with the same type

[Sasha Levin]

From: Qu Wenruo <wqu@suse.com>

[ Upstream commit 2a28468e525f3924efed7f29f2bc5a2926e7e19a ]

[BUG]
With fuzzed image and MIXED_GROUPS super flag, we can hit the following
BUG_ON():

  kernel BUG at fs/btrfs/delayed-ref.c:491!
  invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
  CPU: 0 PID: 1849 Comm: sync Tainted: G           O      5.2.0-custom #27
  RIP: 0010:update_existing_head_ref.cold+0x44/0x46 [btrfs]
  Call Trace:
   add_delayed_ref_head+0x20c/0x2d0 [btrfs]
   btrfs_add_delayed_tree_ref+0x1fc/0x490 [btrfs]
   btrfs_free_tree_block+0x123/0x380 [btrfs]
   __btrfs_cow_block+0x435/0x500 [btrfs]
   btrfs_cow_block+0x110/0x240 [btrfs]
   btrfs_search_slot+0x230/0xa00 [btrfs]
   ? __lock_acquire+0x105e/0x1e20
   btrfs_insert_empty_items+0x67/0xc0 [btrfs]
   alloc_reserved_file_extent+0x9e/0x340 [btrfs]
   __btrfs_run_delayed_refs+0x78e/0x1240 [btrfs]
   ? kvm_clock_read+0x18/0x30
   ? __sched_clock_gtod_offset+0x21/0x50
   btrfs_run_delayed_refs.part.0+0x4e/0x180 [btrfs]
   btrfs_run_delayed_refs+0x23/0x30 [btrfs]
   btrfs_commit_transaction+0x53/0x9f0 [btrfs]
   btrfs_sync_fs+0x7c/0x1c0 [btrfs]
   ? __ia32_sys_fdatasync+0x20/0x20
   sync_fs_one_sb+0x23/0x30
   iterate_supers+0x95/0x100
   ksys_sync+0x62/0xb0
   __ia32_sys_sync+0xe/0x20
   do_syscall_64+0x65/0x240
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

[CAUSE]
This situation is caused by several factors:
- Fuzzed image
  The extent tree of this fs missed one backref for extent tree root.
  So we can allocated space from that slot.

- MIXED_BG feature
  Super block has MIXED_BG flag.

- No mixed block groups exists
  All block groups are just regular ones.

This makes data space_info->block_groups[] contains metadata block
groups.  And when we reserve space for data, we can use space in
metadata block group.

Then we hit the following file operations:

- fallocate
  We need to allocate data extents.
  find_free_extent() choose to use the metadata block to allocate space
  from, and choose the space of extent tree root, since its backref is
  missing.

  This generate one delayed ref head with is_data = 1.

- extent tree update
  We need to update extent tree at run_delayed_ref time.

  This generate one delayed ref head with is_data = 0, for the same
  bytenr of old extent tree root.

Then we trigger the BUG_ON().

[FIX]
The quick fix here is to check block_group->flags before using it.

The problem can only happen for MIXED_GROUPS fs. Regular filesystems
won't have space_info with DATA|METADATA flag, and no way to hit the
bug.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203255
Reported-by: Jungyeon Yoon <jungyeon.yoon@gmail.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/btrfs/extent-tree.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index df2bb4b61a00d..4c316ca3ee785 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -7168,6 +7168,14 @@ static noinline int find_free_extent(struct btrfs_root *orig_root,
 			 */
 			if ((flags & extra) && !(block_group->flags & extra))
 				goto loop;
+
+			/*
+			 * This block group has different flags than we want.
+			 * It's possible that we have MIXED_GROUP flag but no
+			 * block group is mixed.  Just skip such block group.
+			 */
+			btrfs_release_block_group(block_group, delalloc);
+			continue;
 		}
 
 have_block_group:
-- 
2.20.1