All of lore.kernel.org
 help / color / mirror / Atom feed
* [U-Boot] [PATCH 0/8] amlogic: add SEI610 support
@ 2019-10-11 15:33 ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot

Add support for the customer board SEI610 manufactured by SEI Robotics
with the following specifications:
 - Amlogic S905X3 ARM Cortex-A35 quad-core SoC
 - 2GB DDR4 SDRAM
 - 10/100 Ethernet (Internal PHY)
 - 1 x USB 3.0 Host
 - 1 x USB Type-C DRD
 - 1 x FTDI USB Serial Debug Interface
 - eMMC
 - SDcard
 - Infrared receiver
 - SDIO WiFi Module

Like it's SEI510 counterpart, the boot flow is designed to boot
Android AOSP built for the Yukawa Android device.

The SM1 SoC is very close to G12A, so it uses the same arm board code
and reuses what was pushed for SEI510.

For that it needs to reuse the SEI510 android boot flow into
a common flow with custom partitions for each board.

Guillaume La Roque (2):
  configs: sei510: rework header and fix userdata size
  configs: sei610: Add config file to fix userdata size

Neil Armstrong (6):
  ARM: meson: add SM1 SoC id
  mmc: meson-gx: add support for mmc-pwrseq-emmc
  clk: meson-sm1: add compatible
  ARM: dts: Import SEI610 DT from Linux 5.4-rc2
  ARM: dts: meson-sm1: add U-Boot specific DT for graphics
  boards: amlogic: add SEI610 support

 MAINTAINERS                                   |   1 +
 arch/arm/dts/Makefile                         |   3 +-
 ...boot.dtsi => meson-g12-common-u-boot.dtsi} |   0
 arch/arm/dts/meson-g12a-sei510-u-boot.dtsi    |   2 +-
 arch/arm/dts/meson-g12a-u200-u-boot.dtsi      |   2 +-
 arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi |   2 +-
 arch/arm/dts/meson-sm1-sei610-u-boot.dtsi     |   7 +
 arch/arm/dts/meson-sm1-sei610.dts             | 383 ++++++++++++++++++
 arch/arm/dts/meson-sm1.dtsi                   | 147 +++++++
 arch/arm/mach-meson/board-info.c              |   2 +
 board/amlogic/sei610/MAINTAINERS              |   7 +
 board/amlogic/sei610/Makefile                 |   6 +
 board/amlogic/sei610/README                   | 119 ++++++
 board/amlogic/sei610/sei610.c                 |  26 ++
 configs/sei610_defconfig                      |  76 ++++
 drivers/clk/meson/g12a.c                      |   1 +
 drivers/mmc/meson_gx_mmc.c                    |  51 +++
 include/configs/meson64_android.h             | 136 +++++++
 include/configs/sei510.h                      | 121 +-----
 include/configs/sei610.h                      |  31 ++
 include/dt-bindings/power/meson-sm1-power.h   |  18 +
 21 files changed, 1018 insertions(+), 123 deletions(-)
 rename arch/arm/dts/{meson-g12a-u-boot.dtsi => meson-g12-common-u-boot.dtsi} (100%)
 create mode 100644 arch/arm/dts/meson-sm1-sei610-u-boot.dtsi
 create mode 100644 arch/arm/dts/meson-sm1-sei610.dts
 create mode 100644 arch/arm/dts/meson-sm1.dtsi
 create mode 100644 board/amlogic/sei610/MAINTAINERS
 create mode 100644 board/amlogic/sei610/Makefile
 create mode 100644 board/amlogic/sei610/README
 create mode 100644 board/amlogic/sei610/sei610.c
 create mode 100644 configs/sei610_defconfig
 create mode 100644 include/configs/meson64_android.h
 create mode 100644 include/configs/sei610.h
 create mode 100644 include/dt-bindings/power/meson-sm1-power.h

-- 
2.22.0

^ permalink raw reply	[flat|nested] 22+ messages in thread
* [PATCH 0/8] amlogic: add SEI610 support
@ 2019-10-11 15:33 ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic, Neil Armstrong

Add support for the customer board SEI610 manufactured by SEI Robotics
with the following specifications:
 - Amlogic S905X3 ARM Cortex-A35 quad-core SoC
 - 2GB DDR4 SDRAM
 - 10/100 Ethernet (Internal PHY)
 - 1 x USB 3.0 Host
 - 1 x USB Type-C DRD
 - 1 x FTDI USB Serial Debug Interface
 - eMMC
 - SDcard
 - Infrared receiver
 - SDIO WiFi Module

Like it's SEI510 counterpart, the boot flow is designed to boot
Android AOSP built for the Yukawa Android device.

The SM1 SoC is very close to G12A, so it uses the same arm board code
and reuses what was pushed for SEI510.

For that it needs to reuse the SEI510 android boot flow into
a common flow with custom partitions for each board.

Guillaume La Roque (2):
  configs: sei510: rework header and fix userdata size
  configs: sei610: Add config file to fix userdata size

Neil Armstrong (6):
  ARM: meson: add SM1 SoC id
  mmc: meson-gx: add support for mmc-pwrseq-emmc
  clk: meson-sm1: add compatible
  ARM: dts: Import SEI610 DT from Linux 5.4-rc2
  ARM: dts: meson-sm1: add U-Boot specific DT for graphics
  boards: amlogic: add SEI610 support

 MAINTAINERS                                   |   1 +
 arch/arm/dts/Makefile                         |   3 +-
 ...boot.dtsi => meson-g12-common-u-boot.dtsi} |   0
 arch/arm/dts/meson-g12a-sei510-u-boot.dtsi    |   2 +-
 arch/arm/dts/meson-g12a-u200-u-boot.dtsi      |   2 +-
 arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi |   2 +-
 arch/arm/dts/meson-sm1-sei610-u-boot.dtsi     |   7 +
 arch/arm/dts/meson-sm1-sei610.dts             | 383 ++++++++++++++++++
 arch/arm/dts/meson-sm1.dtsi                   | 147 +++++++
 arch/arm/mach-meson/board-info.c              |   2 +
 board/amlogic/sei610/MAINTAINERS              |   7 +
 board/amlogic/sei610/Makefile                 |   6 +
 board/amlogic/sei610/README                   | 119 ++++++
 board/amlogic/sei610/sei610.c                 |  26 ++
 configs/sei610_defconfig                      |  76 ++++
 drivers/clk/meson/g12a.c                      |   1 +
 drivers/mmc/meson_gx_mmc.c                    |  51 +++
 include/configs/meson64_android.h             | 136 +++++++
 include/configs/sei510.h                      | 121 +-----
 include/configs/sei610.h                      |  31 ++
 include/dt-bindings/power/meson-sm1-power.h   |  18 +
 21 files changed, 1018 insertions(+), 123 deletions(-)
 rename arch/arm/dts/{meson-g12a-u-boot.dtsi => meson-g12-common-u-boot.dtsi} (100%)
 create mode 100644 arch/arm/dts/meson-sm1-sei610-u-boot.dtsi
 create mode 100644 arch/arm/dts/meson-sm1-sei610.dts
 create mode 100644 arch/arm/dts/meson-sm1.dtsi
 create mode 100644 board/amlogic/sei610/MAINTAINERS
 create mode 100644 board/amlogic/sei610/Makefile
 create mode 100644 board/amlogic/sei610/README
 create mode 100644 board/amlogic/sei610/sei610.c
 create mode 100644 configs/sei610_defconfig
 create mode 100644 include/configs/meson64_android.h
 create mode 100644 include/configs/sei610.h
 create mode 100644 include/dt-bindings/power/meson-sm1-power.h

-- 
2.22.0


^ permalink raw reply	[flat|nested] 22+ messages in thread
* [U-Boot] [PATCH 1/8] ARM: meson: add SM1 SoC id
  2019-10-11 15:33 ` Neil Armstrong
@ 2019-10-11 15:33   ` Neil Armstrong
  -1 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot

Add the missing IDs to detect the SM1 S905X3 SoC.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm/mach-meson/board-info.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/mach-meson/board-info.c b/arch/arm/mach-meson/board-info.c
index 9571b5a189..0d3b40a249 100644
--- a/arch/arm/mach-meson/board-info.c
+++ b/arch/arm/mach-meson/board-info.c
@@ -34,6 +34,7 @@ static const struct meson_gx_soc_id {
 	{ "TXHD",   0x27 },
 	{ "G12A",   0x28 },
 	{ "G12B",   0x29 },
+	{ "SM1",    0x2b },
 };
 
 static const struct meson_gx_package_id {
@@ -61,6 +62,7 @@ static const struct meson_gx_package_id {
 	{ "S905X2", 0x28, 0x40, 0xf0 },
 	{ "A311D",  0x29, 0x10, 0xf0 },
 	{ "S922X",  0x29, 0x40, 0xf0 },
+	{ "S905X3", 0x2b, 0x5, 0xf },
 };
 
 DECLARE_GLOBAL_DATA_PTR;
-- 
2.22.0

^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [PATCH 1/8] ARM: meson: add SM1 SoC id
@ 2019-10-11 15:33   ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic, Neil Armstrong

Add the missing IDs to detect the SM1 S905X3 SoC.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm/mach-meson/board-info.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/mach-meson/board-info.c b/arch/arm/mach-meson/board-info.c
index 9571b5a189..0d3b40a249 100644
--- a/arch/arm/mach-meson/board-info.c
+++ b/arch/arm/mach-meson/board-info.c
@@ -34,6 +34,7 @@ static const struct meson_gx_soc_id {
 	{ "TXHD",   0x27 },
 	{ "G12A",   0x28 },
 	{ "G12B",   0x29 },
+	{ "SM1",    0x2b },
 };
 
 static const struct meson_gx_package_id {
@@ -61,6 +62,7 @@ static const struct meson_gx_package_id {
 	{ "S905X2", 0x28, 0x40, 0xf0 },
 	{ "A311D",  0x29, 0x10, 0xf0 },
 	{ "S922X",  0x29, 0x40, 0xf0 },
+	{ "S905X3", 0x2b, 0x5, 0xf },
 };
 
 DECLARE_GLOBAL_DATA_PTR;
-- 
2.22.0


^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [U-Boot] [PATCH 2/8] mmc: meson-gx: add support for mmc-pwrseq-emmc
  2019-10-11 15:33 ` Neil Armstrong
@ 2019-10-11 15:33   ` Neil Armstrong
  -1 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot

Add support for mmc-pwrseq-emmc in the meson-gx mmc driver to support
enabling the eMMC.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 drivers/mmc/meson_gx_mmc.c | 51 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 51 insertions(+)

diff --git a/drivers/mmc/meson_gx_mmc.c b/drivers/mmc/meson_gx_mmc.c
index 767dfff805..031cc79ccb 100644
--- a/drivers/mmc/meson_gx_mmc.c
+++ b/drivers/mmc/meson_gx_mmc.c
@@ -7,8 +7,10 @@
 #include <dm.h>
 #include <fdtdec.h>
 #include <malloc.h>
+#include <pwrseq.h>
 #include <mmc.h>
 #include <asm/io.h>
+#include <asm/gpio.h>
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
@@ -239,6 +241,10 @@ static int meson_mmc_probe(struct udevice *dev)
 	struct mmc *mmc = &pdata->mmc;
 	struct mmc_config *cfg = &pdata->cfg;
 	uint32_t val;
+#ifdef CONFIG_PWRSEQ
+	struct udevice *pwr_dev;
+	int ret;
+#endif
 
 	cfg->voltages = MMC_VDD_33_34 | MMC_VDD_32_33 |
 			MMC_VDD_31_32 | MMC_VDD_165_195;
@@ -254,6 +260,17 @@ static int meson_mmc_probe(struct udevice *dev)
 
 	mmc_set_clock(mmc, cfg->f_min, MMC_CLK_ENABLE);
 
+#ifdef CONFIG_PWRSEQ
+	/* Enable power if needed */
+	ret = uclass_get_device_by_phandle(UCLASS_PWRSEQ, dev, "mmc-pwrseq",
+					   &pwr_dev);
+	if (!ret) {
+		ret = pwrseq_set_power(pwr_dev, true);
+		if (ret)
+			return ret;
+	}
+#endif
+
 	/* reset all status bits */
 	meson_write(mmc, STATUS_MASK, MESON_SD_EMMC_STATUS);
 
@@ -292,3 +309,37 @@ U_BOOT_DRIVER(meson_mmc) = {
 	.ofdata_to_platdata = meson_mmc_ofdata_to_platdata,
 	.platdata_auto_alloc_size = sizeof(struct meson_mmc_platdata),
 };
+
+#ifdef CONFIG_PWRSEQ
+static int meson_mmc_pwrseq_set_power(struct udevice *dev, bool enable)
+{
+	struct gpio_desc reset;
+	int ret;
+
+	ret = gpio_request_by_name(dev, "reset-gpios", 0, &reset, GPIOD_IS_OUT);
+	if (ret)
+		return ret;
+	dm_gpio_set_value(&reset, 1);
+	udelay(1);
+	dm_gpio_set_value(&reset, 0);
+	udelay(200);
+
+	return 0;
+}
+
+static const struct pwrseq_ops meson_mmc_pwrseq_ops = {
+	.set_power	= meson_mmc_pwrseq_set_power,
+};
+
+static const struct udevice_id meson_mmc_pwrseq_ids[] = {
+	{ .compatible = "mmc-pwrseq-emmc" },
+	{ }
+};
+
+U_BOOT_DRIVER(meson_mmc_pwrseq_drv) = {
+	.name		= "mmc_pwrseq_emmc",
+	.id		= UCLASS_PWRSEQ,
+	.of_match	= meson_mmc_pwrseq_ids,
+	.ops		= &meson_mmc_pwrseq_ops,
+};
+#endif
-- 
2.22.0

^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [PATCH 2/8] mmc: meson-gx: add support for mmc-pwrseq-emmc
@ 2019-10-11 15:33   ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic, Neil Armstrong

Add support for mmc-pwrseq-emmc in the meson-gx mmc driver to support
enabling the eMMC.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 drivers/mmc/meson_gx_mmc.c | 51 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 51 insertions(+)

diff --git a/drivers/mmc/meson_gx_mmc.c b/drivers/mmc/meson_gx_mmc.c
index 767dfff805..031cc79ccb 100644
--- a/drivers/mmc/meson_gx_mmc.c
+++ b/drivers/mmc/meson_gx_mmc.c
@@ -7,8 +7,10 @@
 #include <dm.h>
 #include <fdtdec.h>
 #include <malloc.h>
+#include <pwrseq.h>
 #include <mmc.h>
 #include <asm/io.h>
+#include <asm/gpio.h>
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
@@ -239,6 +241,10 @@ static int meson_mmc_probe(struct udevice *dev)
 	struct mmc *mmc = &pdata->mmc;
 	struct mmc_config *cfg = &pdata->cfg;
 	uint32_t val;
+#ifdef CONFIG_PWRSEQ
+	struct udevice *pwr_dev;
+	int ret;
+#endif
 
 	cfg->voltages = MMC_VDD_33_34 | MMC_VDD_32_33 |
 			MMC_VDD_31_32 | MMC_VDD_165_195;
@@ -254,6 +260,17 @@ static int meson_mmc_probe(struct udevice *dev)
 
 	mmc_set_clock(mmc, cfg->f_min, MMC_CLK_ENABLE);
 
+#ifdef CONFIG_PWRSEQ
+	/* Enable power if needed */
+	ret = uclass_get_device_by_phandle(UCLASS_PWRSEQ, dev, "mmc-pwrseq",
+					   &pwr_dev);
+	if (!ret) {
+		ret = pwrseq_set_power(pwr_dev, true);
+		if (ret)
+			return ret;
+	}
+#endif
+
 	/* reset all status bits */
 	meson_write(mmc, STATUS_MASK, MESON_SD_EMMC_STATUS);
 
@@ -292,3 +309,37 @@ U_BOOT_DRIVER(meson_mmc) = {
 	.ofdata_to_platdata = meson_mmc_ofdata_to_platdata,
 	.platdata_auto_alloc_size = sizeof(struct meson_mmc_platdata),
 };
+
+#ifdef CONFIG_PWRSEQ
+static int meson_mmc_pwrseq_set_power(struct udevice *dev, bool enable)
+{
+	struct gpio_desc reset;
+	int ret;
+
+	ret = gpio_request_by_name(dev, "reset-gpios", 0, &reset, GPIOD_IS_OUT);
+	if (ret)
+		return ret;
+	dm_gpio_set_value(&reset, 1);
+	udelay(1);
+	dm_gpio_set_value(&reset, 0);
+	udelay(200);
+
+	return 0;
+}
+
+static const struct pwrseq_ops meson_mmc_pwrseq_ops = {
+	.set_power	= meson_mmc_pwrseq_set_power,
+};
+
+static const struct udevice_id meson_mmc_pwrseq_ids[] = {
+	{ .compatible = "mmc-pwrseq-emmc" },
+	{ }
+};
+
+U_BOOT_DRIVER(meson_mmc_pwrseq_drv) = {
+	.name		= "mmc_pwrseq_emmc",
+	.id		= UCLASS_PWRSEQ,
+	.of_match	= meson_mmc_pwrseq_ids,
+	.ops		= &meson_mmc_pwrseq_ops,
+};
+#endif
-- 
2.22.0


^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [U-Boot] [PATCH 3/8] clk: meson-sm1: add compatible
  2019-10-11 15:33 ` Neil Armstrong
@ 2019-10-11 15:33   ` Neil Armstrong
  -1 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot

The SM1 clock controller is almost identical to the G12A and
so far the differences don't matter.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 drivers/clk/meson/g12a.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
index c03738b6ca..1b2523bbf1 100644
--- a/drivers/clk/meson/g12a.c
+++ b/drivers/clk/meson/g12a.c
@@ -992,6 +992,7 @@ static struct clk_ops meson_clk_ops = {
 static const struct udevice_id meson_clk_ids[] = {
 	{ .compatible = "amlogic,g12a-clkc" },
 	{ .compatible = "amlogic,g12b-clkc" },
+	{ .compatible = "amlogic,sm1-clkc" },
 	{ }
 };
 
-- 
2.22.0

^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [PATCH 3/8] clk: meson-sm1: add compatible
@ 2019-10-11 15:33   ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic, Neil Armstrong

The SM1 clock controller is almost identical to the G12A and
so far the differences don't matter.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 drivers/clk/meson/g12a.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
index c03738b6ca..1b2523bbf1 100644
--- a/drivers/clk/meson/g12a.c
+++ b/drivers/clk/meson/g12a.c
@@ -992,6 +992,7 @@ static struct clk_ops meson_clk_ops = {
 static const struct udevice_id meson_clk_ids[] = {
 	{ .compatible = "amlogic,g12a-clkc" },
 	{ .compatible = "amlogic,g12b-clkc" },
+	{ .compatible = "amlogic,sm1-clkc" },
 	{ }
 };
 
-- 
2.22.0


^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [U-Boot] [PATCH 4/8] ARM: dts: Import SEI610 DT from Linux 5.4-rc2
  2019-10-11 15:33 ` Neil Armstrong
@ 2019-10-11 15:33   ` Neil Armstrong
  -1 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot

Import the Amlogic SM1 DT and the SEI610 board DT from [1]

[1] da0c9ea146cb ("Linux 5.4-rc2")

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm/dts/Makefile                       |   3 +-
 arch/arm/dts/meson-sm1-sei610.dts           | 383 ++++++++++++++++++++
 arch/arm/dts/meson-sm1.dtsi                 | 147 ++++++++
 include/dt-bindings/power/meson-sm1-power.h |  18 +
 4 files changed, 550 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/meson-sm1-sei610.dts
 create mode 100644 arch/arm/dts/meson-sm1.dtsi
 create mode 100644 include/dt-bindings/power/meson-sm1-power.h

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index aac3d21ef8..f5b9286fdf 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -142,7 +142,8 @@ dtb-$(CONFIG_ARCH_MESON) += \
 	meson-g12a-u200.dtb \
 	meson-g12a-sei510.dtb \
 	meson-g12b-odroid-n2.dtb \
-	meson-g12b-a311d-khadas-vim3.dtb
+	meson-g12b-a311d-khadas-vim3.dtb \
+	meson-sm1-sei610.dtb
 dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
 	tegra20-medcom-wide.dtb \
 	tegra20-paz00.dtb \
diff --git a/arch/arm/dts/meson-sm1-sei610.dts b/arch/arm/dts/meson-sm1-sei610.dts
new file mode 100644
index 0000000000..3435aaa4e8
--- /dev/null
+++ b/arch/arm/dts/meson-sm1-sei610.dts
@@ -0,0 +1,383 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+	compatible = "seirobotics,sei610", "amlogic,sm1";
+	model = "SEI Robotics SEI610";
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		key1 {
+			label = "A";
+			linux,code = <BTN_0>;
+			gpios = <&gpio GPIOH_6 GPIO_ACTIVE_LOW>;
+		};
+
+		key2 {
+			label = "B";
+			linux,code = <BTN_1>;
+			gpios = <&gpio GPIOH_7 GPIO_ACTIVE_LOW>;
+		};
+
+		key3 {
+			label = "C";
+			linux,code = <BTN_2>;
+			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		bluetooth {
+			label = "sei610:blue:bt";
+			gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+			default-state = "off";
+		};
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+
+		power {
+			label = "sei610:red:power";
+			pwms = <&pwm_AO_ab 0 30518 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+			active-low;
+		};
+	};
+
+	memory at 0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	ao_5v: regulator-ao_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "AO_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_in>;
+		regulator-always-on;
+	};
+
+	dc_in: regulator-dc_in {
+		compatible = "regulator-fixed";
+		regulator-name = "DC_IN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	emmc_1v8: regulator-emmc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "EMMC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_in>;
+		regulator-always-on;
+	};
+
+	/* Used by Tuner, RGB Led & IR Emitter LED array */
+	vddao_3v3_t: regulator-vddao_3v3_t {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3_T";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-low;
+		regulator-always-on;
+	};
+
+	vddcpu: regulator-vddcpu {
+		/*
+		 * SY8120B1ABC DC/DC Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <690000>;
+		regulator-max-microvolt = <1050000>;
+
+		vin-supply = <&dc_in>;
+
+		pwms = <&pwm_AO_cd 1 1500 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddio_ao1v8: regulator-vddio_ao1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	reserved-memory {
+		/* TEE Reserved Memory */
+		bl32_reserved: bl32 at 5000000 {
+			reg = <0x0 0x05300000 0x0 0x2000000>;
+			no-map;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU1_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu2 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU2_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu3 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU3_CLK>;
+	clock-latency = <50000>;
+};
+
+&ethmac {
+	status = "okay";
+	phy-handle = <&internal_ephy>;
+	phy-mode = "rmii";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_AO_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_ao_a_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao1v8>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_ao1v8>;
+
+	brcmf: wifi at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&emmc_1v8>;
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+		clocks = <&wifi32k>;
+		clock-names = "lpo";
+		vbat-supply = <&vddao_3v3>;
+		vddio-supply = <&vddio_ao1v8>;
+	};
+};
+
+/* Exposed via the on-board USB to Serial FT232RL IC */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "otg";
+};
diff --git a/arch/arm/dts/meson-sm1.dtsi b/arch/arm/dts/meson-sm1.dtsi
new file mode 100644
index 0000000000..521573f3a5
--- /dev/null
+++ b/arch/arm/dts/meson-sm1.dtsi
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12-common.dtsi"
+#include <dt-bindings/power/meson-sm1-power.h>
+
+/ {
+	compatible = "amlogic,sm1";
+
+	cpus {
+		#address-cells = <0x2>;
+		#size-cells = <0x0>;
+
+		cpu0: cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu at 2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x2>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu at 3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x3>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	cpu_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <730000>;
+		};
+
+		opp-250000000 {
+			opp-hz = /bits/ 64 <250000000>;
+			opp-microvolt = <730000>;
+		};
+
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <730000>;
+		};
+
+		opp-667000000 {
+			opp-hz = /bits/ 64 <666666666>;
+			opp-microvolt = <750000>;
+		};
+
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <770000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <780000>;
+		};
+
+		opp-1404000000 {
+			opp-hz = /bits/ 64 <1404000000>;
+			opp-microvolt = <790000>;
+		};
+
+		opp-1512000000 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <800000>;
+		};
+
+		opp-1608000000 {
+			opp-hz = /bits/ 64 <1608000000>;
+			opp-microvolt = <810000>;
+		};
+
+		opp-1704000000 {
+			opp-hz = /bits/ 64 <1704000000>;
+			opp-microvolt = <850000>;
+		};
+
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <900000>;
+		};
+
+		opp-1908000000 {
+			opp-hz = /bits/ 64 <1908000000>;
+			opp-microvolt = <950000>;
+		};
+	};
+};
+
+&cecb_AO {
+	compatible = "amlogic,meson-sm1-ao-cec";
+};
+
+&clk_msr {
+	compatible = "amlogic,meson-sm1-clk-measure";
+};
+
+
+&clkc {
+	compatible = "amlogic,sm1-clkc";
+};
+
+&ethmac {
+	power-domains = <&pwrc PWRC_SM1_ETH_ID>;
+};
+
+&pwrc {
+	compatible = "amlogic,meson-sm1-pwrc";
+};
+
+&vpu {
+	power-domains = <&pwrc PWRC_SM1_VPU_ID>;
+};
+
+&usb {
+	power-domains = <&pwrc PWRC_SM1_USB_ID>;
+};
diff --git a/include/dt-bindings/power/meson-sm1-power.h b/include/dt-bindings/power/meson-sm1-power.h
new file mode 100644
index 0000000000..a020ab00c1
--- /dev/null
+++ b/include/dt-bindings/power/meson-sm1-power.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#ifndef _DT_BINDINGS_MESON_SM1_POWER_H
+#define _DT_BINDINGS_MESON_SM1_POWER_H
+
+#define PWRC_SM1_VPU_ID		0
+#define PWRC_SM1_NNA_ID		1
+#define PWRC_SM1_USB_ID		2
+#define PWRC_SM1_PCIE_ID	3
+#define PWRC_SM1_GE2D_ID	4
+#define PWRC_SM1_AUDIO_ID	5
+#define PWRC_SM1_ETH_ID		6
+
+#endif
-- 
2.22.0

^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [PATCH 4/8] ARM: dts: Import SEI610 DT from Linux 5.4-rc2
@ 2019-10-11 15:33   ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic, Neil Armstrong

Import the Amlogic SM1 DT and the SEI610 board DT from [1]

[1] da0c9ea146cb ("Linux 5.4-rc2")

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm/dts/Makefile                       |   3 +-
 arch/arm/dts/meson-sm1-sei610.dts           | 383 ++++++++++++++++++++
 arch/arm/dts/meson-sm1.dtsi                 | 147 ++++++++
 include/dt-bindings/power/meson-sm1-power.h |  18 +
 4 files changed, 550 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/meson-sm1-sei610.dts
 create mode 100644 arch/arm/dts/meson-sm1.dtsi
 create mode 100644 include/dt-bindings/power/meson-sm1-power.h

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index aac3d21ef8..f5b9286fdf 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -142,7 +142,8 @@ dtb-$(CONFIG_ARCH_MESON) += \
 	meson-g12a-u200.dtb \
 	meson-g12a-sei510.dtb \
 	meson-g12b-odroid-n2.dtb \
-	meson-g12b-a311d-khadas-vim3.dtb
+	meson-g12b-a311d-khadas-vim3.dtb \
+	meson-sm1-sei610.dtb
 dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
 	tegra20-medcom-wide.dtb \
 	tegra20-paz00.dtb \
diff --git a/arch/arm/dts/meson-sm1-sei610.dts b/arch/arm/dts/meson-sm1-sei610.dts
new file mode 100644
index 0000000000..3435aaa4e8
--- /dev/null
+++ b/arch/arm/dts/meson-sm1-sei610.dts
@@ -0,0 +1,383 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+	compatible = "seirobotics,sei610", "amlogic,sm1";
+	model = "SEI Robotics SEI610";
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		key1 {
+			label = "A";
+			linux,code = <BTN_0>;
+			gpios = <&gpio GPIOH_6 GPIO_ACTIVE_LOW>;
+		};
+
+		key2 {
+			label = "B";
+			linux,code = <BTN_1>;
+			gpios = <&gpio GPIOH_7 GPIO_ACTIVE_LOW>;
+		};
+
+		key3 {
+			label = "C";
+			linux,code = <BTN_2>;
+			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		bluetooth {
+			label = "sei610:blue:bt";
+			gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+			default-state = "off";
+		};
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+
+		power {
+			label = "sei610:red:power";
+			pwms = <&pwm_AO_ab 0 30518 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+			active-low;
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	ao_5v: regulator-ao_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "AO_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_in>;
+		regulator-always-on;
+	};
+
+	dc_in: regulator-dc_in {
+		compatible = "regulator-fixed";
+		regulator-name = "DC_IN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	emmc_1v8: regulator-emmc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "EMMC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_in>;
+		regulator-always-on;
+	};
+
+	/* Used by Tuner, RGB Led & IR Emitter LED array */
+	vddao_3v3_t: regulator-vddao_3v3_t {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3_T";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-low;
+		regulator-always-on;
+	};
+
+	vddcpu: regulator-vddcpu {
+		/*
+		 * SY8120B1ABC DC/DC Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <690000>;
+		regulator-max-microvolt = <1050000>;
+
+		vin-supply = <&dc_in>;
+
+		pwms = <&pwm_AO_cd 1 1500 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddio_ao1v8: regulator-vddio_ao1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	reserved-memory {
+		/* TEE Reserved Memory */
+		bl32_reserved: bl32@5000000 {
+			reg = <0x0 0x05300000 0x0 0x2000000>;
+			no-map;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU1_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu2 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU2_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu3 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU3_CLK>;
+	clock-latency = <50000>;
+};
+
+&ethmac {
+	status = "okay";
+	phy-handle = <&internal_ephy>;
+	phy-mode = "rmii";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_AO_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_ao_a_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao1v8>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_ao1v8>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&emmc_1v8>;
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+		clocks = <&wifi32k>;
+		clock-names = "lpo";
+		vbat-supply = <&vddao_3v3>;
+		vddio-supply = <&vddio_ao1v8>;
+	};
+};
+
+/* Exposed via the on-board USB to Serial FT232RL IC */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "otg";
+};
diff --git a/arch/arm/dts/meson-sm1.dtsi b/arch/arm/dts/meson-sm1.dtsi
new file mode 100644
index 0000000000..521573f3a5
--- /dev/null
+++ b/arch/arm/dts/meson-sm1.dtsi
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12-common.dtsi"
+#include <dt-bindings/power/meson-sm1-power.h>
+
+/ {
+	compatible = "amlogic,sm1";
+
+	cpus {
+		#address-cells = <0x2>;
+		#size-cells = <0x0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x2>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x3>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	cpu_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <730000>;
+		};
+
+		opp-250000000 {
+			opp-hz = /bits/ 64 <250000000>;
+			opp-microvolt = <730000>;
+		};
+
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <730000>;
+		};
+
+		opp-667000000 {
+			opp-hz = /bits/ 64 <666666666>;
+			opp-microvolt = <750000>;
+		};
+
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <770000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <780000>;
+		};
+
+		opp-1404000000 {
+			opp-hz = /bits/ 64 <1404000000>;
+			opp-microvolt = <790000>;
+		};
+
+		opp-1512000000 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <800000>;
+		};
+
+		opp-1608000000 {
+			opp-hz = /bits/ 64 <1608000000>;
+			opp-microvolt = <810000>;
+		};
+
+		opp-1704000000 {
+			opp-hz = /bits/ 64 <1704000000>;
+			opp-microvolt = <850000>;
+		};
+
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <900000>;
+		};
+
+		opp-1908000000 {
+			opp-hz = /bits/ 64 <1908000000>;
+			opp-microvolt = <950000>;
+		};
+	};
+};
+
+&cecb_AO {
+	compatible = "amlogic,meson-sm1-ao-cec";
+};
+
+&clk_msr {
+	compatible = "amlogic,meson-sm1-clk-measure";
+};
+
+
+&clkc {
+	compatible = "amlogic,sm1-clkc";
+};
+
+&ethmac {
+	power-domains = <&pwrc PWRC_SM1_ETH_ID>;
+};
+
+&pwrc {
+	compatible = "amlogic,meson-sm1-pwrc";
+};
+
+&vpu {
+	power-domains = <&pwrc PWRC_SM1_VPU_ID>;
+};
+
+&usb {
+	power-domains = <&pwrc PWRC_SM1_USB_ID>;
+};
diff --git a/include/dt-bindings/power/meson-sm1-power.h b/include/dt-bindings/power/meson-sm1-power.h
new file mode 100644
index 0000000000..a020ab00c1
--- /dev/null
+++ b/include/dt-bindings/power/meson-sm1-power.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#ifndef _DT_BINDINGS_MESON_SM1_POWER_H
+#define _DT_BINDINGS_MESON_SM1_POWER_H
+
+#define PWRC_SM1_VPU_ID		0
+#define PWRC_SM1_NNA_ID		1
+#define PWRC_SM1_USB_ID		2
+#define PWRC_SM1_PCIE_ID	3
+#define PWRC_SM1_GE2D_ID	4
+#define PWRC_SM1_AUDIO_ID	5
+#define PWRC_SM1_ETH_ID		6
+
+#endif
-- 
2.22.0


^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [U-Boot] [PATCH 5/8] ARM: dts: meson-sm1: add U-Boot specific DT for graphics
  2019-10-11 15:33 ` Neil Armstrong
@ 2019-10-11 15:33   ` Neil Armstrong
  -1 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot

Rename meson-g12a-u-boot.dtsi into meson-g12-common-u-boot.dtsi to
match the new DT architecture and add meson-sm1-sei610-u-boot.dtsi
to handle the U-Boot specific DT for graphics.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 ...meson-g12a-u-boot.dtsi => meson-g12-common-u-boot.dtsi} | 0
 arch/arm/dts/meson-g12a-sei510-u-boot.dtsi                 | 2 +-
 arch/arm/dts/meson-g12a-u200-u-boot.dtsi                   | 2 +-
 arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi              | 2 +-
 arch/arm/dts/meson-sm1-sei610-u-boot.dtsi                  | 7 +++++++
 5 files changed, 10 insertions(+), 3 deletions(-)
 rename arch/arm/dts/{meson-g12a-u-boot.dtsi => meson-g12-common-u-boot.dtsi} (100%)
 create mode 100644 arch/arm/dts/meson-sm1-sei610-u-boot.dtsi

diff --git a/arch/arm/dts/meson-g12a-u-boot.dtsi b/arch/arm/dts/meson-g12-common-u-boot.dtsi
similarity index 100%
rename from arch/arm/dts/meson-g12a-u-boot.dtsi
rename to arch/arm/dts/meson-g12-common-u-boot.dtsi
diff --git a/arch/arm/dts/meson-g12a-sei510-u-boot.dtsi b/arch/arm/dts/meson-g12a-sei510-u-boot.dtsi
index fddffd628c..236f2468dc 100644
--- a/arch/arm/dts/meson-g12a-sei510-u-boot.dtsi
+++ b/arch/arm/dts/meson-g12a-sei510-u-boot.dtsi
@@ -4,4 +4,4 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include "meson-g12a-u-boot.dtsi"
+#include "meson-g12-common-u-boot.dtsi"
diff --git a/arch/arm/dts/meson-g12a-u200-u-boot.dtsi b/arch/arm/dts/meson-g12a-u200-u-boot.dtsi
index fddffd628c..236f2468dc 100644
--- a/arch/arm/dts/meson-g12a-u200-u-boot.dtsi
+++ b/arch/arm/dts/meson-g12a-u200-u-boot.dtsi
@@ -4,4 +4,4 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include "meson-g12a-u-boot.dtsi"
+#include "meson-g12-common-u-boot.dtsi"
diff --git a/arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi b/arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi
index fddffd628c..236f2468dc 100644
--- a/arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi
+++ b/arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi
@@ -4,4 +4,4 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include "meson-g12a-u-boot.dtsi"
+#include "meson-g12-common-u-boot.dtsi"
diff --git a/arch/arm/dts/meson-sm1-sei610-u-boot.dtsi b/arch/arm/dts/meson-sm1-sei610-u-boot.dtsi
new file mode 100644
index 0000000000..236f2468dc
--- /dev/null
+++ b/arch/arm/dts/meson-sm1-sei610-u-boot.dtsi
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12-common-u-boot.dtsi"
-- 
2.22.0

^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [PATCH 5/8] ARM: dts: meson-sm1: add U-Boot specific DT for graphics
@ 2019-10-11 15:33   ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic, Neil Armstrong

Rename meson-g12a-u-boot.dtsi into meson-g12-common-u-boot.dtsi to
match the new DT architecture and add meson-sm1-sei610-u-boot.dtsi
to handle the U-Boot specific DT for graphics.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 ...meson-g12a-u-boot.dtsi => meson-g12-common-u-boot.dtsi} | 0
 arch/arm/dts/meson-g12a-sei510-u-boot.dtsi                 | 2 +-
 arch/arm/dts/meson-g12a-u200-u-boot.dtsi                   | 2 +-
 arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi              | 2 +-
 arch/arm/dts/meson-sm1-sei610-u-boot.dtsi                  | 7 +++++++
 5 files changed, 10 insertions(+), 3 deletions(-)
 rename arch/arm/dts/{meson-g12a-u-boot.dtsi => meson-g12-common-u-boot.dtsi} (100%)
 create mode 100644 arch/arm/dts/meson-sm1-sei610-u-boot.dtsi

diff --git a/arch/arm/dts/meson-g12a-u-boot.dtsi b/arch/arm/dts/meson-g12-common-u-boot.dtsi
similarity index 100%
rename from arch/arm/dts/meson-g12a-u-boot.dtsi
rename to arch/arm/dts/meson-g12-common-u-boot.dtsi
diff --git a/arch/arm/dts/meson-g12a-sei510-u-boot.dtsi b/arch/arm/dts/meson-g12a-sei510-u-boot.dtsi
index fddffd628c..236f2468dc 100644
--- a/arch/arm/dts/meson-g12a-sei510-u-boot.dtsi
+++ b/arch/arm/dts/meson-g12a-sei510-u-boot.dtsi
@@ -4,4 +4,4 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include "meson-g12a-u-boot.dtsi"
+#include "meson-g12-common-u-boot.dtsi"
diff --git a/arch/arm/dts/meson-g12a-u200-u-boot.dtsi b/arch/arm/dts/meson-g12a-u200-u-boot.dtsi
index fddffd628c..236f2468dc 100644
--- a/arch/arm/dts/meson-g12a-u200-u-boot.dtsi
+++ b/arch/arm/dts/meson-g12a-u200-u-boot.dtsi
@@ -4,4 +4,4 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include "meson-g12a-u-boot.dtsi"
+#include "meson-g12-common-u-boot.dtsi"
diff --git a/arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi b/arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi
index fddffd628c..236f2468dc 100644
--- a/arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi
+++ b/arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi
@@ -4,4 +4,4 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include "meson-g12a-u-boot.dtsi"
+#include "meson-g12-common-u-boot.dtsi"
diff --git a/arch/arm/dts/meson-sm1-sei610-u-boot.dtsi b/arch/arm/dts/meson-sm1-sei610-u-boot.dtsi
new file mode 100644
index 0000000000..236f2468dc
--- /dev/null
+++ b/arch/arm/dts/meson-sm1-sei610-u-boot.dtsi
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12-common-u-boot.dtsi"
-- 
2.22.0


^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [U-Boot] [PATCH 6/8] boards: amlogic: add SEI610 support
  2019-10-11 15:33 ` Neil Armstrong
@ 2019-10-11 15:33   ` Neil Armstrong
  -1 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot

Add support for the customer board SEI610 manufactured by SEI Robotics
with the following specifications:
 - Amlogic S905X3 ARM Cortex-A35 quad-core SoC
 - 2GB DDR4 SDRAM
 - 10/100 Ethernet (Internal PHY)
 - 1 x USB 3.0 Host
 - 1 x USB Type-C DRD
 - 1 x FTDI USB Serial Debug Interface
 - eMMC
 - SDcard
 - Infrared receiver
 - SDIO WiFi Module

Like it's SEI510 counterpart, the boot flow is designed to boot
Android AOSP built for the Yukawa Android device.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 board/amlogic/sei610/MAINTAINERS |   6 ++
 board/amlogic/sei610/Makefile    |   6 ++
 board/amlogic/sei610/README      | 119 +++++++++++++++++++++++++++++++
 board/amlogic/sei610/sei610.c    |  26 +++++++
 configs/sei610_defconfig         |  76 ++++++++++++++++++++
 5 files changed, 233 insertions(+)
 create mode 100644 board/amlogic/sei610/MAINTAINERS
 create mode 100644 board/amlogic/sei610/Makefile
 create mode 100644 board/amlogic/sei610/README
 create mode 100644 board/amlogic/sei610/sei610.c
 create mode 100644 configs/sei610_defconfig

diff --git a/board/amlogic/sei610/MAINTAINERS b/board/amlogic/sei610/MAINTAINERS
new file mode 100644
index 0000000000..20f12334e9
--- /dev/null
+++ b/board/amlogic/sei610/MAINTAINERS
@@ -0,0 +1,6 @@
+SEI610
+M:	Neil Armstrong <narmstrong@baylibre.com>
+S:	Maintained
+L:	u-boot-amlogic at groups.io
+F:	board/amlogic/sei610/
+F:	configs/sei610_defconfig
diff --git a/board/amlogic/sei610/Makefile b/board/amlogic/sei610/Makefile
new file mode 100644
index 0000000000..428792afea
--- /dev/null
+++ b/board/amlogic/sei610/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2016 BayLibre, SAS
+# Author: Neil Armstrong <narmstrong@baylibre.com>
+
+obj-y	:= sei610.o
diff --git a/board/amlogic/sei610/README b/board/amlogic/sei610/README
new file mode 100644
index 0000000000..836809ccdb
--- /dev/null
+++ b/board/amlogic/sei610/README
@@ -0,0 +1,119 @@
+U-Boot for Amlogic SEI610
+=======================
+
+SEI610 is a customer board manufactured by SEI Robotics with the following
+specifications:
+
+ - Amlogic S905X3 ARM Cortex-A35 quad-core SoC
+ - 2GB DDR4 SDRAM
+ - 10/100 Ethernet (Internal PHY)
+ - 1 x USB 3.0 Host
+ - 1 x USB Type-C DRD
+ - 1 x FTDI USB Serial Debug Interface
+ - eMMC
+ - SDcard
+ - Infrared receiver
+ - SDIO WiFi Module
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make sei610_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b buildroot-openlinux-4.9-g12a-201904 amlogic-u-boot
+ > cd amlogic-u-boot
+ > make sm1_ac200_v1_defconfig
+ > make
+ > export UBOOTDIR=$PWD
+
+Download the latest Amlogic Buildroot package, and extract it :
+ > wget http://openlinux2.amlogic.com:8000/ARM/filesystem/buildroot-openlinux-A113-201901.tgz
+ > tar xfz buildroot-openlinux-A113-201901.tgz buildroot-openlinux-A113-201901/bootloader
+ > export BRDIR=$PWD/buildroot-openlinux-A113-201901
+ > export FIPDIR=$BRDIR/bootloader/uboot-repo/fip
+
+Go back to mainline U-Boot source tree then :
+ > mkdir fip
+
+ > wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
+ > cp $UBOOTDIR/build/scp_task/bl301.bin fip/
+ > cp $UBOOTDIR/build/board/amlogic/g12a_u200_v1/firmware/acs.bin fip/
+ > cp $BRDIR/bootloader/uboot-repo/bl2/bin/g12a/bl2.bin fip/
+ > cp $BRDIR/bootloader/uboot-repo/bl30/bin/g12a/bl30.bin fip/
+ > cp $BRDIR/bootloader/uboot-repo/bl31_1.3/bin/g12a/bl31.img fip/
+ > cp $FIPDIR/g12a/ddr3_1d.fw fip/
+ > cp $FIPDIR/g12a/ddr4_1d.fw fip/
+ > cp $FIPDIR/g12a/ddr4_2d.fw fip/
+ > cp $FIPDIR/g12a/diag_lpddr4.fw fip/
+ > cp $FIPDIR/g12a/lpddr4_1d.fw fip/
+ > cp $FIPDIR/g12a/lpddr4_2d.fw fip/
+ > cp $FIPDIR/g12a/piei.fw fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > sh fip/blx_fix.sh \
+	fip/bl30.bin \
+	fip/zero_tmp \
+	fip/bl30_zero.bin \
+	fip/bl301.bin \
+	fip/bl301_zero.bin \
+	fip/bl30_new.bin \
+	bl30
+
+ > sh fip/blx_fix.sh \
+	fip/bl2.bin \
+	fip/zero_tmp \
+	fip/bl2_zero.bin \
+	fip/acs.bin \
+	fip/bl21_zero.bin \
+	fip/bl2_new.bin \
+	bl2
+
+ > $FIPDIR/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \
+					--output fip/bl30_new.bin.g12a.enc \
+					--level v3
+ > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \
+					--output fip/bl30_new.bin.enc \
+					--level v3 --type bl30
+ > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \
+					--output fip/bl31.img.enc \
+					--level v3 --type bl31
+ > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \
+					--output fip/bl33.bin.enc \
+					--level v3 --type bl33
+ > $FIPDIR/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \
+					--output fip/bl2.n.bin.sig
+ > $FIPDIR/g12a/aml_encrypt_g12a --bootmk \
+		--output fip/u-boot.bin \
+		--bl2 fip/bl2.n.bin.sig \
+		--bl30 fip/bl30_new.bin.enc \
+		--bl31 fip/bl31.img.enc \
+		--bl33 fip/bl33.bin.enc \
+		--ddrfw1 fip/ddr4_1d.fw \
+		--ddrfw2 fip/ddr4_2d.fw \
+		--ddrfw3 fip/ddr3_1d.fw \
+		--ddrfw4 fip/piei.fw \
+		--ddrfw5 fip/lpddr4_1d.fw \
+		--ddrfw6 fip/lpddr4_2d.fw \
+		--ddrfw7 fip/diag_lpddr4.fw \
+		--level v3
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
diff --git a/board/amlogic/sei610/sei610.c b/board/amlogic/sei610/sei610.c
new file mode 100644
index 0000000000..b17eb9ef55
--- /dev/null
+++ b/board/amlogic/sei610/sei610.c
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <env_internal.h>
+#include <asm/io.h>
+#include <asm/arch/axg.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+#include <asm/arch/mem.h>
+
+int misc_init_r(void)
+{
+	meson_eth_init(PHY_INTERFACE_MODE_RMII,
+		       MESON_USE_INTERNAL_RMII_PHY);
+
+	meson_generate_serial_ethaddr();
+
+	env_set("serial#", "AMLG12ASEI610");
+
+	return 0;
+}
diff --git a/configs/sei610_defconfig b/configs/sei610_defconfig
new file mode 100644
index 0000000000..89e7bd7bab
--- /dev/null
+++ b/configs/sei610_defconfig
@@ -0,0 +1,76 @@
+CONFIG_ARM=y
+CONFIG_SYS_BOARD="sei610"
+CONFIG_SYS_CONFIG_NAME="sei510"
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_MESON_G12A=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEBUG_UART_BASE=0xff803000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" sei610"
+# CONFIG_PSCI_RESET is not set
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_USE_PREBOOT=y
+CONFIG_PREBOOT="run load_logo"
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_MISC_INIT_R=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_BMP=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-sm1-sei610"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_USB_FUNCTION_FASTBOOT=y
+CONFIG_FASTBOOT_BUF_ADDR=0x6000000
+CONFIG_FASTBOOT_FLASH=y
+CONFIG_FASTBOOT_FLASH_MMC_DEV=2
+CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
+CONFIG_DM_GPIO=y
+# CONFIG_INPUT is not set
+CONFIG_PWRSEQ=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_PHY_ADDR_ENABLE=y
+CONFIG_PHY_ADDR=8
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_MESON_G12A_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_G12A=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MESON_EE_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_MESON_G12A=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x18d1
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_VIDEO_MESON=y
+CONFIG_VIDEO_DT_SIMPLEFB=y
+CONFIG_LZ4=y
+CONFIG_OF_LIBFDT_OVERLAY=y
-- 
2.22.0

^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [PATCH 6/8] boards: amlogic: add SEI610 support
@ 2019-10-11 15:33   ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic, Neil Armstrong

Add support for the customer board SEI610 manufactured by SEI Robotics
with the following specifications:
 - Amlogic S905X3 ARM Cortex-A35 quad-core SoC
 - 2GB DDR4 SDRAM
 - 10/100 Ethernet (Internal PHY)
 - 1 x USB 3.0 Host
 - 1 x USB Type-C DRD
 - 1 x FTDI USB Serial Debug Interface
 - eMMC
 - SDcard
 - Infrared receiver
 - SDIO WiFi Module

Like it's SEI510 counterpart, the boot flow is designed to boot
Android AOSP built for the Yukawa Android device.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 board/amlogic/sei610/MAINTAINERS |   6 ++
 board/amlogic/sei610/Makefile    |   6 ++
 board/amlogic/sei610/README      | 119 +++++++++++++++++++++++++++++++
 board/amlogic/sei610/sei610.c    |  26 +++++++
 configs/sei610_defconfig         |  76 ++++++++++++++++++++
 5 files changed, 233 insertions(+)
 create mode 100644 board/amlogic/sei610/MAINTAINERS
 create mode 100644 board/amlogic/sei610/Makefile
 create mode 100644 board/amlogic/sei610/README
 create mode 100644 board/amlogic/sei610/sei610.c
 create mode 100644 configs/sei610_defconfig

diff --git a/board/amlogic/sei610/MAINTAINERS b/board/amlogic/sei610/MAINTAINERS
new file mode 100644
index 0000000000..20f12334e9
--- /dev/null
+++ b/board/amlogic/sei610/MAINTAINERS
@@ -0,0 +1,6 @@
+SEI610
+M:	Neil Armstrong <narmstrong@baylibre.com>
+S:	Maintained
+L:	u-boot-amlogic@groups.io
+F:	board/amlogic/sei610/
+F:	configs/sei610_defconfig
diff --git a/board/amlogic/sei610/Makefile b/board/amlogic/sei610/Makefile
new file mode 100644
index 0000000000..428792afea
--- /dev/null
+++ b/board/amlogic/sei610/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2016 BayLibre, SAS
+# Author: Neil Armstrong <narmstrong@baylibre.com>
+
+obj-y	:= sei610.o
diff --git a/board/amlogic/sei610/README b/board/amlogic/sei610/README
new file mode 100644
index 0000000000..836809ccdb
--- /dev/null
+++ b/board/amlogic/sei610/README
@@ -0,0 +1,119 @@
+U-Boot for Amlogic SEI610
+=======================
+
+SEI610 is a customer board manufactured by SEI Robotics with the following
+specifications:
+
+ - Amlogic S905X3 ARM Cortex-A35 quad-core SoC
+ - 2GB DDR4 SDRAM
+ - 10/100 Ethernet (Internal PHY)
+ - 1 x USB 3.0 Host
+ - 1 x USB Type-C DRD
+ - 1 x FTDI USB Serial Debug Interface
+ - eMMC
+ - SDcard
+ - Infrared receiver
+ - SDIO WiFi Module
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make sei610_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b buildroot-openlinux-4.9-g12a-201904 amlogic-u-boot
+ > cd amlogic-u-boot
+ > make sm1_ac200_v1_defconfig
+ > make
+ > export UBOOTDIR=$PWD
+
+Download the latest Amlogic Buildroot package, and extract it :
+ > wget http://openlinux2.amlogic.com:8000/ARM/filesystem/buildroot-openlinux-A113-201901.tgz
+ > tar xfz buildroot-openlinux-A113-201901.tgz buildroot-openlinux-A113-201901/bootloader
+ > export BRDIR=$PWD/buildroot-openlinux-A113-201901
+ > export FIPDIR=$BRDIR/bootloader/uboot-repo/fip
+
+Go back to mainline U-Boot source tree then :
+ > mkdir fip
+
+ > wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
+ > cp $UBOOTDIR/build/scp_task/bl301.bin fip/
+ > cp $UBOOTDIR/build/board/amlogic/g12a_u200_v1/firmware/acs.bin fip/
+ > cp $BRDIR/bootloader/uboot-repo/bl2/bin/g12a/bl2.bin fip/
+ > cp $BRDIR/bootloader/uboot-repo/bl30/bin/g12a/bl30.bin fip/
+ > cp $BRDIR/bootloader/uboot-repo/bl31_1.3/bin/g12a/bl31.img fip/
+ > cp $FIPDIR/g12a/ddr3_1d.fw fip/
+ > cp $FIPDIR/g12a/ddr4_1d.fw fip/
+ > cp $FIPDIR/g12a/ddr4_2d.fw fip/
+ > cp $FIPDIR/g12a/diag_lpddr4.fw fip/
+ > cp $FIPDIR/g12a/lpddr4_1d.fw fip/
+ > cp $FIPDIR/g12a/lpddr4_2d.fw fip/
+ > cp $FIPDIR/g12a/piei.fw fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > sh fip/blx_fix.sh \
+	fip/bl30.bin \
+	fip/zero_tmp \
+	fip/bl30_zero.bin \
+	fip/bl301.bin \
+	fip/bl301_zero.bin \
+	fip/bl30_new.bin \
+	bl30
+
+ > sh fip/blx_fix.sh \
+	fip/bl2.bin \
+	fip/zero_tmp \
+	fip/bl2_zero.bin \
+	fip/acs.bin \
+	fip/bl21_zero.bin \
+	fip/bl2_new.bin \
+	bl2
+
+ > $FIPDIR/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \
+					--output fip/bl30_new.bin.g12a.enc \
+					--level v3
+ > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \
+					--output fip/bl30_new.bin.enc \
+					--level v3 --type bl30
+ > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \
+					--output fip/bl31.img.enc \
+					--level v3 --type bl31
+ > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \
+					--output fip/bl33.bin.enc \
+					--level v3 --type bl33
+ > $FIPDIR/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \
+					--output fip/bl2.n.bin.sig
+ > $FIPDIR/g12a/aml_encrypt_g12a --bootmk \
+		--output fip/u-boot.bin \
+		--bl2 fip/bl2.n.bin.sig \
+		--bl30 fip/bl30_new.bin.enc \
+		--bl31 fip/bl31.img.enc \
+		--bl33 fip/bl33.bin.enc \
+		--ddrfw1 fip/ddr4_1d.fw \
+		--ddrfw2 fip/ddr4_2d.fw \
+		--ddrfw3 fip/ddr3_1d.fw \
+		--ddrfw4 fip/piei.fw \
+		--ddrfw5 fip/lpddr4_1d.fw \
+		--ddrfw6 fip/lpddr4_2d.fw \
+		--ddrfw7 fip/diag_lpddr4.fw \
+		--level v3
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
diff --git a/board/amlogic/sei610/sei610.c b/board/amlogic/sei610/sei610.c
new file mode 100644
index 0000000000..b17eb9ef55
--- /dev/null
+++ b/board/amlogic/sei610/sei610.c
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <env_internal.h>
+#include <asm/io.h>
+#include <asm/arch/axg.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+#include <asm/arch/mem.h>
+
+int misc_init_r(void)
+{
+	meson_eth_init(PHY_INTERFACE_MODE_RMII,
+		       MESON_USE_INTERNAL_RMII_PHY);
+
+	meson_generate_serial_ethaddr();
+
+	env_set("serial#", "AMLG12ASEI610");
+
+	return 0;
+}
diff --git a/configs/sei610_defconfig b/configs/sei610_defconfig
new file mode 100644
index 0000000000..89e7bd7bab
--- /dev/null
+++ b/configs/sei610_defconfig
@@ -0,0 +1,76 @@
+CONFIG_ARM=y
+CONFIG_SYS_BOARD="sei610"
+CONFIG_SYS_CONFIG_NAME="sei510"
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_MESON_G12A=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEBUG_UART_BASE=0xff803000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" sei610"
+# CONFIG_PSCI_RESET is not set
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_USE_PREBOOT=y
+CONFIG_PREBOOT="run load_logo"
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_MISC_INIT_R=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_BMP=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-sm1-sei610"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_USB_FUNCTION_FASTBOOT=y
+CONFIG_FASTBOOT_BUF_ADDR=0x6000000
+CONFIG_FASTBOOT_FLASH=y
+CONFIG_FASTBOOT_FLASH_MMC_DEV=2
+CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
+CONFIG_DM_GPIO=y
+# CONFIG_INPUT is not set
+CONFIG_PWRSEQ=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_PHY_ADDR_ENABLE=y
+CONFIG_PHY_ADDR=8
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_MESON_G12A_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_G12A=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MESON_EE_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_MESON_G12A=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x18d1
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_VIDEO_MESON=y
+CONFIG_VIDEO_DT_SIMPLEFB=y
+CONFIG_LZ4=y
+CONFIG_OF_LIBFDT_OVERLAY=y
-- 
2.22.0


^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [U-Boot] [PATCH 7/8] configs: sei510: rework header and fix userdata size
  2019-10-11 15:33 ` Neil Armstrong
@ 2019-10-11 15:33   ` Neil Armstrong
  -1 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot

From: Guillaume La Roque <glaroque@baylibre.com>

Move android generic config and boot sequence in meson64_android header
and fix size of userdata to use all eMMC on SEI510.

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 MAINTAINERS                       |   1 +
 include/configs/meson64_android.h | 136 ++++++++++++++++++++++++++++++
 include/configs/sei510.h          | 121 +-------------------------
 3 files changed, 139 insertions(+), 119 deletions(-)
 create mode 100644 include/configs/meson64_android.h

diff --git a/MAINTAINERS b/MAINTAINERS
index c53656695a..e874a44c31 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -137,6 +137,7 @@ F:	drivers/pinctrl/meson/
 F:	drivers/power/domain/meson-gx-pwrc-vpu.c
 F:	drivers/video/meson/
 F:	include/configs/meson64.h
+F:	include/configs/meson64_android.h
 N:	meson
 
 ARM BROADCOM BCM283X
diff --git a/include/configs/meson64_android.h b/include/configs/meson64_android.h
new file mode 100644
index 0000000000..055fb44e93
--- /dev/null
+++ b/include/configs/meson64_android.h
@@ -0,0 +1,136 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration for Android Amlogic Meson 64bits SoCs
+ *
+ * Copyright (C) 2019 Baylibre, SAS
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+#ifndef __MESON64_ANDROID_CONFIG_H
+#define __MESON64_ANDROID_CONFIG_H
+
+#define CONFIG_SYS_MMC_ENV_DEV	2
+#define CONFIG_SYS_MMC_ENV_PART	1
+#define CONFIG_ENV_SIZE		0x10000
+#define CONFIG_ENV_OFFSET	(-0x10000)
+
+
+#define BOOTENV_DEV_FASTBOOT(devtypeu, devtypel, instance) \
+	"bootcmd_fastboot=" \
+		"sm reboot_reason reason;" \
+		"setenv run_fastboot 0;" \
+		"if test \"${boot_source}\" = \"usb\"; then " \
+			"echo Fastboot forced by usb rom boot;" \
+			"setenv run_fastboot 1;" \
+		"fi;" \
+		"if gpt verify mmc ${mmcdev} ${partitions}; then; " \
+		"else " \
+			"echo Broken MMC partition scheme;" \
+			"setenv run_fastboot 1;" \
+		"fi;" \
+		"if test \"${reason}\" = \"bootloader\" -o " \
+			"\"${reason}\" = \"fastboot\"; then " \
+			"echo Fastboot asked by reboot reason;" \
+			"setenv run_fastboot 1;" \
+		"fi;" \
+		"if test \"${skip_fastboot}\" -eq 1; then " \
+			"echo Fastboot skipped by environment;" \
+			"setenv run_fastboot 0;" \
+		"fi;" \
+		"if test \"${force_fastboot}\" -eq 1; then " \
+			"echo Fastboot forced by environment;" \
+			"setenv run_fastboot 1;" \
+		"fi;" \
+		"if test \"${run_fastboot}\" -eq 1; then " \
+			"echo Running Fastboot...;" \
+			"fastboot 0;" \
+		"fi\0"
+
+#define BOOTENV_DEV_NAME_FASTBOOT(devtypeu, devtypel, instance)	\
+		"fastboot "
+
+/* TOFIX: Run actual recovery instead of fastboot */
+#define BOOTENV_DEV_RECOVERY(devtypeu, devtypel, instance) \
+	"bootcmd_recovery=" \
+		"pinmux dev pinctrl at 14;" \
+		"pinmux dev pinctrl at 40;" \
+		"sm reboot_reason reason;" \
+		"setenv run_recovery 0;" \
+		"if run check_button; then " \
+			"echo Recovery button is pressed;" \
+			"setenv run_recovery 1;" \
+		"elif test \"${reason}\" = \"recovery\" -o " \
+			  "\"${reason}\" = \"update\"; then " \
+			"echo Recovery asked by reboot reason;" \
+			"setenv run_recovery 1;" \
+		"fi;" \
+		"if test \"${skip_recovery}\" -eq 1; then " \
+			"echo Recovery skipped by environment;" \
+			"setenv run_recovery 0;" \
+		"fi;" \
+		"if test \"${force_recovery}\" -eq 1; then " \
+			"echo Recovery forced by environment;" \
+			"setenv run_recovery 1;" \
+		"fi;" \
+		"if test \"${run_recovery}\" -eq 1; then " \
+			"echo Running Recovery...;" \
+			"fastboot 0;" \
+		"fi\0"
+
+#define BOOTENV_DEV_NAME_RECOVERY(devtypeu, devtypel, instance)	\
+		"recovery "
+
+#define BOOTENV_DEV_SYSTEM(devtypeu, devtypel, instance) \
+	"bootcmd_system=" \
+		"echo Loading Android boot partition...;" \
+		"mmc dev ${mmcdev};" \
+		"setenv bootargs ${bootargs} console=${console} androidboot.serialno=${serial#};" \
+		"part start mmc ${mmcdev} ${bootpart} boot_start;" \
+		"part size mmc ${mmcdev} ${bootpart} boot_size;" \
+		"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
+			"echo Running Android...;" \
+			"bootm ${loadaddr};" \
+		"fi;" \
+		"echo Failed to boot Android...;" \
+		"reset\0"
+
+#define BOOTENV_DEV_NAME_SYSTEM(devtypeu, devtypel, instance)	\
+		"system "
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(FASTBOOT, fastboot, na) \
+	func(RECOVERY, recovery, na) \
+	func(SYSTEM, system, na) \
+
+#define PREBOOT_LOAD_LOGO \
+	"mmc dev ${mmcdev};" \
+	"part start mmc ${mmcdev} ${logopart} boot_start;" \
+	"part size mmc ${mmcdev} ${logopart} boot_size;" \
+	"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
+			"bmp display ${loadaddr} m m;" \
+	"fi;"
+
+#define CONFIG_EXTRA_ENV_SETTINGS                                     \
+	"partitions=" PARTS_DEFAULT "\0"                              \
+	"mmcdev=2\0"                                                  \
+	"bootpart=1\0"                                                \
+	"logopart=2\0"                                                \
+	"gpio_recovery=88\0"                                          \
+	"check_button=gpio input ${gpio_recovery};test $? -eq 0;\0"   \
+	"load_logo=" PREBOOT_LOAD_LOGO "\0"			      \
+	"console=/dev/ttyAML0\0"                                      \
+	"bootargs=no_console_suspend\0"                               \
+	"stdin=" STDIN_CFG "\0"                                       \
+	"stdout=" STDOUT_CFG "\0"                                     \
+	"stderr=" STDOUT_CFG "\0"                                     \
+	"loadaddr=0x01000000\0"                                       \
+	"fdt_addr_r=0x01000000\0"                                     \
+	"scriptaddr=0x08000000\0"                                     \
+	"kernel_addr_r=0x01080000\0"                                  \
+	"pxefile_addr_r=0x01080000\0"                                 \
+	"ramdisk_addr_r=0x13000000\0"                                 \
+	"fdtfile=amlogic/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" BOOTENV
+
+#include <configs/meson64.h>
+
+#endif /* __MESON64_ANDROID_CONFIG_H */
diff --git a/include/configs/sei510.h b/include/configs/sei510.h
index 5bf982cada..d37b4c6405 100644
--- a/include/configs/sei510.h
+++ b/include/configs/sei510.h
@@ -9,11 +9,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_MMC_ENV_DEV	2
-#define CONFIG_SYS_MMC_ENV_PART	1
-#define CONFIG_ENV_SIZE		0x10000
-#define CONFIG_ENV_OFFSET	(-0x10000)
-
 #define LOGO_UUID "43a3305d-150f-4cc9-bd3b-38fca8693846;"
 #define CACHE_UUID "99207ae6-5207-11e9-999e-6f77a3612069;"
 #define SYSTEM_UUID "99f9b7ac-5207-11e9-8507-c3c037e393f3;"
@@ -28,122 +23,10 @@
 	"name=cache,size=256M,uuid=" CACHE_UUID             \
 	"name=system,size=1536M,uuid=" SYSTEM_UUID           \
 	"name=vendor,size=256M,uuid=" VENDOR_UUID            \
-	"name=userdata,size=4746M,uuid=" USERDATA_UUID	\
+	"name=userdata,size=5341M,uuid=" USERDATA_UUID	\
 	"name=rootfs,size=-,uuid=" ROOT_UUID
 
-#define BOOTENV_DEV_FASTBOOT(devtypeu, devtypel, instance) \
-	"bootcmd_fastboot=" \
-		"sm reboot_reason reason;" \
-		"setenv run_fastboot 0;" \
-		"if gpt verify mmc ${mmcdev} ${partitions}; then; " \
-		"else " \
-			"echo Broken MMC partition scheme;" \
-			"setenv run_fastboot 1;" \
-		"fi;" \
-		"if test \"${reason}\" = \"bootloader\" -o " \
-			"\"${reason}\" = \"fastboot\"; then " \
-			"echo Fastboot asked by reboot reason;" \
-			"setenv run_fastboot 1;" \
-		"fi;" \
-		"if test \"${skip_fastboot}\" -eq 1; then " \
-			"echo Fastboot skipped by environment;" \
-			"setenv run_fastboot 0;" \
-		"fi;" \
-		"if test \"${force_fastboot}\" -eq 1; then " \
-			"echo Fastboot forced by environment;" \
-			"setenv run_fastboot 1;" \
-		"fi;" \
-		"if test \"${run_fastboot}\" -eq 1; then " \
-			"echo Running Fastboot...;" \
-			"fastboot 0;" \
-		"fi\0"
-
-#define BOOTENV_DEV_NAME_FASTBOOT(devtypeu, devtypel, instance)	\
-		"fastboot "
-
-/* TOFIX: Run actual recovery instead of fastboot */
-#define BOOTENV_DEV_RECOVERY(devtypeu, devtypel, instance) \
-	"bootcmd_recovery=" \
-		"pinmux dev pinctrl at 14;" \
-		"pinmux dev pinctrl at 40;" \
-		"sm reboot_reason reason;" \
-		"setenv run_recovery 0;" \
-		"if run check_button; then " \
-			"echo Recovery button is pressed;" \
-			"setenv run_recovery 1;" \
-		"elif test \"${reason}\" = \"recovery\" -o " \
-			  "\"${reason}\" = \"update\"; then " \
-			"echo Recovery asked by reboot reason;" \
-			"setenv run_recovery 1;" \
-		"fi;" \
-		"if test \"${skip_recovery}\" -eq 1; then " \
-			"echo Recovery skipped by environment;" \
-			"setenv run_recovery 0;" \
-		"fi;" \
-		"if test \"${force_recovery}\" -eq 1; then " \
-			"echo Recovery forced by environment;" \
-			"setenv run_recovery 1;" \
-		"fi;" \
-		"if test \"${run_recovery}\" -eq 1; then " \
-			"echo Running Recovery...;" \
-			"fastboot 0;" \
-		"fi\0"
-
-#define BOOTENV_DEV_NAME_RECOVERY(devtypeu, devtypel, instance)	\
-		"recovery "
-
-#define BOOTENV_DEV_SYSTEM(devtypeu, devtypel, instance) \
-	"bootcmd_system=" \
-		"echo Loading Android boot partition...;" \
-		"mmc dev ${mmcdev};" \
-		"setenv bootargs ${bootargs} console=${console} androidboot.serialno=${serial#};" \
-		"part start mmc ${mmcdev} ${bootpart} boot_start;" \
-		"part size mmc ${mmcdev} ${bootpart} boot_size;" \
-		"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
-			"echo Running Android...;" \
-			"bootm ${loadaddr};" \
-		"fi;" \
-		"echo Failed to boot Android...;" \
-		"reset\0"
-
-#define BOOTENV_DEV_NAME_SYSTEM(devtypeu, devtypel, instance)	\
-		"system "
-
-#define BOOT_TARGET_DEVICES(func) \
-	func(ROMUSB, romusb, na)  \
-	func(FASTBOOT, fastboot, na) \
-	func(RECOVERY, recovery, na) \
-	func(SYSTEM, system, na) \
-
-#define PREBOOT_LOAD_LOGO \
-	"mmc dev ${mmcdev};" \
-	"part start mmc ${mmcdev} ${logopart} boot_start;" \
-	"part size mmc ${mmcdev} ${logopart} boot_size;" \
-	"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
-			"bmp display ${loadaddr} m m;" \
-	"fi;"
-
-#define CONFIG_EXTRA_ENV_SETTINGS                                     \
-	"partitions=" PARTS_DEFAULT "\0"                              \
-	"mmcdev=2\0"                                                  \
-	"bootpart=1\0"                                                \
-	"logopart=2\0"                                                \
-	"gpio_recovery=88\0"                                          \
-	"check_button=gpio input ${gpio_recovery};test $? -eq 0;\0"   \
-	"load_logo=" PREBOOT_LOAD_LOGO "\0"			      \
-	"console=/dev/ttyAML0\0"                                      \
-	"bootargs=no_console_suspend\0"                               \
-	"stdin=" STDIN_CFG "\0"                                       \
-	"stdout=" STDOUT_CFG "\0"                                     \
-	"stderr=" STDOUT_CFG "\0"                                     \
-	"loadaddr=0x01000000\0"                                       \
-	"fdt_addr_r=0x01000000\0"                                     \
-	"scriptaddr=0x08000000\0"                                     \
-	"kernel_addr_r=0x01080000\0"                                  \
-	"pxefile_addr_r=0x01080000\0"                                 \
-	"ramdisk_addr_r=0x13000000\0"                                 \
-	"fdtfile=amlogic/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" BOOTENV
 
-#include <configs/meson64.h>
+#include <configs/meson64_android.h>
 
 #endif /* __CONFIG_H */
-- 
2.22.0

^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [PATCH 7/8] configs: sei510: rework header and fix userdata size
@ 2019-10-11 15:33   ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic, Guillaume La Roque, Neil Armstrong

From: Guillaume La Roque <glaroque@baylibre.com>

Move android generic config and boot sequence in meson64_android header
and fix size of userdata to use all eMMC on SEI510.

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 MAINTAINERS                       |   1 +
 include/configs/meson64_android.h | 136 ++++++++++++++++++++++++++++++
 include/configs/sei510.h          | 121 +-------------------------
 3 files changed, 139 insertions(+), 119 deletions(-)
 create mode 100644 include/configs/meson64_android.h

diff --git a/MAINTAINERS b/MAINTAINERS
index c53656695a..e874a44c31 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -137,6 +137,7 @@ F:	drivers/pinctrl/meson/
 F:	drivers/power/domain/meson-gx-pwrc-vpu.c
 F:	drivers/video/meson/
 F:	include/configs/meson64.h
+F:	include/configs/meson64_android.h
 N:	meson
 
 ARM BROADCOM BCM283X
diff --git a/include/configs/meson64_android.h b/include/configs/meson64_android.h
new file mode 100644
index 0000000000..055fb44e93
--- /dev/null
+++ b/include/configs/meson64_android.h
@@ -0,0 +1,136 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration for Android Amlogic Meson 64bits SoCs
+ *
+ * Copyright (C) 2019 Baylibre, SAS
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+#ifndef __MESON64_ANDROID_CONFIG_H
+#define __MESON64_ANDROID_CONFIG_H
+
+#define CONFIG_SYS_MMC_ENV_DEV	2
+#define CONFIG_SYS_MMC_ENV_PART	1
+#define CONFIG_ENV_SIZE		0x10000
+#define CONFIG_ENV_OFFSET	(-0x10000)
+
+
+#define BOOTENV_DEV_FASTBOOT(devtypeu, devtypel, instance) \
+	"bootcmd_fastboot=" \
+		"sm reboot_reason reason;" \
+		"setenv run_fastboot 0;" \
+		"if test \"${boot_source}\" = \"usb\"; then " \
+			"echo Fastboot forced by usb rom boot;" \
+			"setenv run_fastboot 1;" \
+		"fi;" \
+		"if gpt verify mmc ${mmcdev} ${partitions}; then; " \
+		"else " \
+			"echo Broken MMC partition scheme;" \
+			"setenv run_fastboot 1;" \
+		"fi;" \
+		"if test \"${reason}\" = \"bootloader\" -o " \
+			"\"${reason}\" = \"fastboot\"; then " \
+			"echo Fastboot asked by reboot reason;" \
+			"setenv run_fastboot 1;" \
+		"fi;" \
+		"if test \"${skip_fastboot}\" -eq 1; then " \
+			"echo Fastboot skipped by environment;" \
+			"setenv run_fastboot 0;" \
+		"fi;" \
+		"if test \"${force_fastboot}\" -eq 1; then " \
+			"echo Fastboot forced by environment;" \
+			"setenv run_fastboot 1;" \
+		"fi;" \
+		"if test \"${run_fastboot}\" -eq 1; then " \
+			"echo Running Fastboot...;" \
+			"fastboot 0;" \
+		"fi\0"
+
+#define BOOTENV_DEV_NAME_FASTBOOT(devtypeu, devtypel, instance)	\
+		"fastboot "
+
+/* TOFIX: Run actual recovery instead of fastboot */
+#define BOOTENV_DEV_RECOVERY(devtypeu, devtypel, instance) \
+	"bootcmd_recovery=" \
+		"pinmux dev pinctrl@14;" \
+		"pinmux dev pinctrl@40;" \
+		"sm reboot_reason reason;" \
+		"setenv run_recovery 0;" \
+		"if run check_button; then " \
+			"echo Recovery button is pressed;" \
+			"setenv run_recovery 1;" \
+		"elif test \"${reason}\" = \"recovery\" -o " \
+			  "\"${reason}\" = \"update\"; then " \
+			"echo Recovery asked by reboot reason;" \
+			"setenv run_recovery 1;" \
+		"fi;" \
+		"if test \"${skip_recovery}\" -eq 1; then " \
+			"echo Recovery skipped by environment;" \
+			"setenv run_recovery 0;" \
+		"fi;" \
+		"if test \"${force_recovery}\" -eq 1; then " \
+			"echo Recovery forced by environment;" \
+			"setenv run_recovery 1;" \
+		"fi;" \
+		"if test \"${run_recovery}\" -eq 1; then " \
+			"echo Running Recovery...;" \
+			"fastboot 0;" \
+		"fi\0"
+
+#define BOOTENV_DEV_NAME_RECOVERY(devtypeu, devtypel, instance)	\
+		"recovery "
+
+#define BOOTENV_DEV_SYSTEM(devtypeu, devtypel, instance) \
+	"bootcmd_system=" \
+		"echo Loading Android boot partition...;" \
+		"mmc dev ${mmcdev};" \
+		"setenv bootargs ${bootargs} console=${console} androidboot.serialno=${serial#};" \
+		"part start mmc ${mmcdev} ${bootpart} boot_start;" \
+		"part size mmc ${mmcdev} ${bootpart} boot_size;" \
+		"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
+			"echo Running Android...;" \
+			"bootm ${loadaddr};" \
+		"fi;" \
+		"echo Failed to boot Android...;" \
+		"reset\0"
+
+#define BOOTENV_DEV_NAME_SYSTEM(devtypeu, devtypel, instance)	\
+		"system "
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(FASTBOOT, fastboot, na) \
+	func(RECOVERY, recovery, na) \
+	func(SYSTEM, system, na) \
+
+#define PREBOOT_LOAD_LOGO \
+	"mmc dev ${mmcdev};" \
+	"part start mmc ${mmcdev} ${logopart} boot_start;" \
+	"part size mmc ${mmcdev} ${logopart} boot_size;" \
+	"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
+			"bmp display ${loadaddr} m m;" \
+	"fi;"
+
+#define CONFIG_EXTRA_ENV_SETTINGS                                     \
+	"partitions=" PARTS_DEFAULT "\0"                              \
+	"mmcdev=2\0"                                                  \
+	"bootpart=1\0"                                                \
+	"logopart=2\0"                                                \
+	"gpio_recovery=88\0"                                          \
+	"check_button=gpio input ${gpio_recovery};test $? -eq 0;\0"   \
+	"load_logo=" PREBOOT_LOAD_LOGO "\0"			      \
+	"console=/dev/ttyAML0\0"                                      \
+	"bootargs=no_console_suspend\0"                               \
+	"stdin=" STDIN_CFG "\0"                                       \
+	"stdout=" STDOUT_CFG "\0"                                     \
+	"stderr=" STDOUT_CFG "\0"                                     \
+	"loadaddr=0x01000000\0"                                       \
+	"fdt_addr_r=0x01000000\0"                                     \
+	"scriptaddr=0x08000000\0"                                     \
+	"kernel_addr_r=0x01080000\0"                                  \
+	"pxefile_addr_r=0x01080000\0"                                 \
+	"ramdisk_addr_r=0x13000000\0"                                 \
+	"fdtfile=amlogic/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" BOOTENV
+
+#include <configs/meson64.h>
+
+#endif /* __MESON64_ANDROID_CONFIG_H */
diff --git a/include/configs/sei510.h b/include/configs/sei510.h
index 5bf982cada..d37b4c6405 100644
--- a/include/configs/sei510.h
+++ b/include/configs/sei510.h
@@ -9,11 +9,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_MMC_ENV_DEV	2
-#define CONFIG_SYS_MMC_ENV_PART	1
-#define CONFIG_ENV_SIZE		0x10000
-#define CONFIG_ENV_OFFSET	(-0x10000)
-
 #define LOGO_UUID "43a3305d-150f-4cc9-bd3b-38fca8693846;"
 #define CACHE_UUID "99207ae6-5207-11e9-999e-6f77a3612069;"
 #define SYSTEM_UUID "99f9b7ac-5207-11e9-8507-c3c037e393f3;"
@@ -28,122 +23,10 @@
 	"name=cache,size=256M,uuid=" CACHE_UUID             \
 	"name=system,size=1536M,uuid=" SYSTEM_UUID           \
 	"name=vendor,size=256M,uuid=" VENDOR_UUID            \
-	"name=userdata,size=4746M,uuid=" USERDATA_UUID	\
+	"name=userdata,size=5341M,uuid=" USERDATA_UUID	\
 	"name=rootfs,size=-,uuid=" ROOT_UUID
 
-#define BOOTENV_DEV_FASTBOOT(devtypeu, devtypel, instance) \
-	"bootcmd_fastboot=" \
-		"sm reboot_reason reason;" \
-		"setenv run_fastboot 0;" \
-		"if gpt verify mmc ${mmcdev} ${partitions}; then; " \
-		"else " \
-			"echo Broken MMC partition scheme;" \
-			"setenv run_fastboot 1;" \
-		"fi;" \
-		"if test \"${reason}\" = \"bootloader\" -o " \
-			"\"${reason}\" = \"fastboot\"; then " \
-			"echo Fastboot asked by reboot reason;" \
-			"setenv run_fastboot 1;" \
-		"fi;" \
-		"if test \"${skip_fastboot}\" -eq 1; then " \
-			"echo Fastboot skipped by environment;" \
-			"setenv run_fastboot 0;" \
-		"fi;" \
-		"if test \"${force_fastboot}\" -eq 1; then " \
-			"echo Fastboot forced by environment;" \
-			"setenv run_fastboot 1;" \
-		"fi;" \
-		"if test \"${run_fastboot}\" -eq 1; then " \
-			"echo Running Fastboot...;" \
-			"fastboot 0;" \
-		"fi\0"
-
-#define BOOTENV_DEV_NAME_FASTBOOT(devtypeu, devtypel, instance)	\
-		"fastboot "
-
-/* TOFIX: Run actual recovery instead of fastboot */
-#define BOOTENV_DEV_RECOVERY(devtypeu, devtypel, instance) \
-	"bootcmd_recovery=" \
-		"pinmux dev pinctrl@14;" \
-		"pinmux dev pinctrl@40;" \
-		"sm reboot_reason reason;" \
-		"setenv run_recovery 0;" \
-		"if run check_button; then " \
-			"echo Recovery button is pressed;" \
-			"setenv run_recovery 1;" \
-		"elif test \"${reason}\" = \"recovery\" -o " \
-			  "\"${reason}\" = \"update\"; then " \
-			"echo Recovery asked by reboot reason;" \
-			"setenv run_recovery 1;" \
-		"fi;" \
-		"if test \"${skip_recovery}\" -eq 1; then " \
-			"echo Recovery skipped by environment;" \
-			"setenv run_recovery 0;" \
-		"fi;" \
-		"if test \"${force_recovery}\" -eq 1; then " \
-			"echo Recovery forced by environment;" \
-			"setenv run_recovery 1;" \
-		"fi;" \
-		"if test \"${run_recovery}\" -eq 1; then " \
-			"echo Running Recovery...;" \
-			"fastboot 0;" \
-		"fi\0"
-
-#define BOOTENV_DEV_NAME_RECOVERY(devtypeu, devtypel, instance)	\
-		"recovery "
-
-#define BOOTENV_DEV_SYSTEM(devtypeu, devtypel, instance) \
-	"bootcmd_system=" \
-		"echo Loading Android boot partition...;" \
-		"mmc dev ${mmcdev};" \
-		"setenv bootargs ${bootargs} console=${console} androidboot.serialno=${serial#};" \
-		"part start mmc ${mmcdev} ${bootpart} boot_start;" \
-		"part size mmc ${mmcdev} ${bootpart} boot_size;" \
-		"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
-			"echo Running Android...;" \
-			"bootm ${loadaddr};" \
-		"fi;" \
-		"echo Failed to boot Android...;" \
-		"reset\0"
-
-#define BOOTENV_DEV_NAME_SYSTEM(devtypeu, devtypel, instance)	\
-		"system "
-
-#define BOOT_TARGET_DEVICES(func) \
-	func(ROMUSB, romusb, na)  \
-	func(FASTBOOT, fastboot, na) \
-	func(RECOVERY, recovery, na) \
-	func(SYSTEM, system, na) \
-
-#define PREBOOT_LOAD_LOGO \
-	"mmc dev ${mmcdev};" \
-	"part start mmc ${mmcdev} ${logopart} boot_start;" \
-	"part size mmc ${mmcdev} ${logopart} boot_size;" \
-	"if mmc read ${loadaddr} ${boot_start} ${boot_size}; then " \
-			"bmp display ${loadaddr} m m;" \
-	"fi;"
-
-#define CONFIG_EXTRA_ENV_SETTINGS                                     \
-	"partitions=" PARTS_DEFAULT "\0"                              \
-	"mmcdev=2\0"                                                  \
-	"bootpart=1\0"                                                \
-	"logopart=2\0"                                                \
-	"gpio_recovery=88\0"                                          \
-	"check_button=gpio input ${gpio_recovery};test $? -eq 0;\0"   \
-	"load_logo=" PREBOOT_LOAD_LOGO "\0"			      \
-	"console=/dev/ttyAML0\0"                                      \
-	"bootargs=no_console_suspend\0"                               \
-	"stdin=" STDIN_CFG "\0"                                       \
-	"stdout=" STDOUT_CFG "\0"                                     \
-	"stderr=" STDOUT_CFG "\0"                                     \
-	"loadaddr=0x01000000\0"                                       \
-	"fdt_addr_r=0x01000000\0"                                     \
-	"scriptaddr=0x08000000\0"                                     \
-	"kernel_addr_r=0x01080000\0"                                  \
-	"pxefile_addr_r=0x01080000\0"                                 \
-	"ramdisk_addr_r=0x13000000\0"                                 \
-	"fdtfile=amlogic/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" BOOTENV
 
-#include <configs/meson64.h>
+#include <configs/meson64_android.h>
 
 #endif /* __CONFIG_H */
-- 
2.22.0


^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [U-Boot] [PATCH 8/8] configs: sei610: Add config file to fix userdata size
  2019-10-11 15:33 ` Neil Armstrong
@ 2019-10-11 15:33   ` Neil Armstrong
  -1 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot

From: Guillaume La Roque <glaroque@baylibre.com>

Add separate config file to handle the different eMMC size on
the sei610 board.

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 board/amlogic/sei610/MAINTAINERS |  1 +
 configs/sei610_defconfig         |  2 +-
 include/configs/sei610.h         | 31 +++++++++++++++++++++++++++++++
 3 files changed, 33 insertions(+), 1 deletion(-)
 create mode 100644 include/configs/sei610.h

diff --git a/board/amlogic/sei610/MAINTAINERS b/board/amlogic/sei610/MAINTAINERS
index 20f12334e9..da77aafa41 100644
--- a/board/amlogic/sei610/MAINTAINERS
+++ b/board/amlogic/sei610/MAINTAINERS
@@ -4,3 +4,4 @@ S:	Maintained
 L:	u-boot-amlogic at groups.io
 F:	board/amlogic/sei610/
 F:	configs/sei610_defconfig
+F:	include/configs/sei610.h
diff --git a/configs/sei610_defconfig b/configs/sei610_defconfig
index 89e7bd7bab..520a683d2e 100644
--- a/configs/sei610_defconfig
+++ b/configs/sei610_defconfig
@@ -1,6 +1,6 @@
 CONFIG_ARM=y
 CONFIG_SYS_BOARD="sei610"
-CONFIG_SYS_CONFIG_NAME="sei510"
+CONFIG_SYS_CONFIG_NAME="sei610"
 CONFIG_ARCH_MESON=y
 CONFIG_SYS_TEXT_BASE=0x01000000
 CONFIG_MESON_G12A=y
diff --git a/include/configs/sei610.h b/include/configs/sei610.h
new file mode 100644
index 0000000000..6d093161c9
--- /dev/null
+++ b/include/configs/sei610.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration for the SEI510
+ *
+ * Copyright (C) 2019 Baylibre, SAS
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define LOGO_UUID "43a3305d-150f-4cc9-bd3b-38fca8693846;"
+#define CACHE_UUID "99207ae6-5207-11e9-999e-6f77a3612069;"
+#define SYSTEM_UUID "99f9b7ac-5207-11e9-8507-c3c037e393f3;"
+#define VENDOR_UUID "9d082802-5207-11e9-954c-cbbce08ba108;"
+#define USERDATA_UUID "9b976e42-5207-11e9-8f16-ff47ac594b22;"
+#define ROOT_UUID "ddb8c3f6-d94d-4394-b633-3134139cc2e0;"
+
+#define PARTS_DEFAULT                                        \
+	"uuid_disk=${uuid_gpt_disk};"  			\
+	"name=boot,size=64M,bootable,uuid=${uuid_gpt_boot};" \
+	"name=logo,size=2M,uuid=" LOGO_UUID             \
+	"name=cache,size=256M,uuid=" CACHE_UUID             \
+	"name=system,size=1536M,uuid=" SYSTEM_UUID           \
+	"name=vendor,size=256M,uuid=" VENDOR_UUID            \
+	"name=userdata,size=12795M,uuid=" USERDATA_UUID	\
+	"name=rootfs,size=-,uuid=" ROOT_UUID
+
+#include <configs/meson64_android.h>
+
+#endif /* __CONFIG_H */
-- 
2.22.0

^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [PATCH 8/8] configs: sei610: Add config file to fix userdata size
@ 2019-10-11 15:33   ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-11 15:33 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic, Guillaume La Roque, Neil Armstrong

From: Guillaume La Roque <glaroque@baylibre.com>

Add separate config file to handle the different eMMC size on
the sei610 board.

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 board/amlogic/sei610/MAINTAINERS |  1 +
 configs/sei610_defconfig         |  2 +-
 include/configs/sei610.h         | 31 +++++++++++++++++++++++++++++++
 3 files changed, 33 insertions(+), 1 deletion(-)
 create mode 100644 include/configs/sei610.h

diff --git a/board/amlogic/sei610/MAINTAINERS b/board/amlogic/sei610/MAINTAINERS
index 20f12334e9..da77aafa41 100644
--- a/board/amlogic/sei610/MAINTAINERS
+++ b/board/amlogic/sei610/MAINTAINERS
@@ -4,3 +4,4 @@ S:	Maintained
 L:	u-boot-amlogic@groups.io
 F:	board/amlogic/sei610/
 F:	configs/sei610_defconfig
+F:	include/configs/sei610.h
diff --git a/configs/sei610_defconfig b/configs/sei610_defconfig
index 89e7bd7bab..520a683d2e 100644
--- a/configs/sei610_defconfig
+++ b/configs/sei610_defconfig
@@ -1,6 +1,6 @@
 CONFIG_ARM=y
 CONFIG_SYS_BOARD="sei610"
-CONFIG_SYS_CONFIG_NAME="sei510"
+CONFIG_SYS_CONFIG_NAME="sei610"
 CONFIG_ARCH_MESON=y
 CONFIG_SYS_TEXT_BASE=0x01000000
 CONFIG_MESON_G12A=y
diff --git a/include/configs/sei610.h b/include/configs/sei610.h
new file mode 100644
index 0000000000..6d093161c9
--- /dev/null
+++ b/include/configs/sei610.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration for the SEI510
+ *
+ * Copyright (C) 2019 Baylibre, SAS
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define LOGO_UUID "43a3305d-150f-4cc9-bd3b-38fca8693846;"
+#define CACHE_UUID "99207ae6-5207-11e9-999e-6f77a3612069;"
+#define SYSTEM_UUID "99f9b7ac-5207-11e9-8507-c3c037e393f3;"
+#define VENDOR_UUID "9d082802-5207-11e9-954c-cbbce08ba108;"
+#define USERDATA_UUID "9b976e42-5207-11e9-8f16-ff47ac594b22;"
+#define ROOT_UUID "ddb8c3f6-d94d-4394-b633-3134139cc2e0;"
+
+#define PARTS_DEFAULT                                        \
+	"uuid_disk=${uuid_gpt_disk};"  			\
+	"name=boot,size=64M,bootable,uuid=${uuid_gpt_boot};" \
+	"name=logo,size=2M,uuid=" LOGO_UUID             \
+	"name=cache,size=256M,uuid=" CACHE_UUID             \
+	"name=system,size=1536M,uuid=" SYSTEM_UUID           \
+	"name=vendor,size=256M,uuid=" VENDOR_UUID            \
+	"name=userdata,size=12795M,uuid=" USERDATA_UUID	\
+	"name=rootfs,size=-,uuid=" ROOT_UUID
+
+#include <configs/meson64_android.h>
+
+#endif /* __CONFIG_H */
-- 
2.22.0


^ permalink raw reply related	[flat|nested] 22+ messages in thread
* [U-Boot] [PATCH 6/8] boards: amlogic: add SEI610 support
  2019-10-11 15:33   ` Neil Armstrong
@ 2019-10-18  8:32     ` Neil Armstrong
  -1 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-18  8:32 UTC (permalink / raw)
  To: u-boot

On 11/10/2019 17:33, Neil Armstrong wrote:
> Add support for the customer board SEI610 manufactured by SEI Robotics
> with the following specifications:
>  - Amlogic S905X3 ARM Cortex-A35 quad-core SoC

--------------------------------/\

Cortex-A55, will fix while applying

>  - 2GB DDR4 SDRAM
>  - 10/100 Ethernet (Internal PHY)
>  - 1 x USB 3.0 Host
>  - 1 x USB Type-C DRD
>  - 1 x FTDI USB Serial Debug Interface
>  - eMMC
>  - SDcard
>  - Infrared receiver
>  - SDIO WiFi Module
> 
> Like it's SEI510 counterpart, the boot flow is designed to boot
> Android AOSP built for the Yukawa Android device.
> 
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
>  board/amlogic/sei610/MAINTAINERS |   6 ++
>  board/amlogic/sei610/Makefile    |   6 ++
>  board/amlogic/sei610/README      | 119 +++++++++++++++++++++++++++++++
>  board/amlogic/sei610/sei610.c    |  26 +++++++
>  configs/sei610_defconfig         |  76 ++++++++++++++++++++
>  5 files changed, 233 insertions(+)
>  create mode 100644 board/amlogic/sei610/MAINTAINERS
>  create mode 100644 board/amlogic/sei610/Makefile
>  create mode 100644 board/amlogic/sei610/README
>  create mode 100644 board/amlogic/sei610/sei610.c
>  create mode 100644 configs/sei610_defconfig
> 
> diff --git a/board/amlogic/sei610/MAINTAINERS b/board/amlogic/sei610/MAINTAINERS
> new file mode 100644
> index 0000000000..20f12334e9
> --- /dev/null
> +++ b/board/amlogic/sei610/MAINTAINERS
> @@ -0,0 +1,6 @@
> +SEI610
> +M:	Neil Armstrong <narmstrong@baylibre.com>
> +S:	Maintained
> +L:	u-boot-amlogic at groups.io
> +F:	board/amlogic/sei610/
> +F:	configs/sei610_defconfig
> diff --git a/board/amlogic/sei610/Makefile b/board/amlogic/sei610/Makefile
> new file mode 100644
> index 0000000000..428792afea
> --- /dev/null
> +++ b/board/amlogic/sei610/Makefile
> @@ -0,0 +1,6 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +# (C) Copyright 2016 BayLibre, SAS
> +# Author: Neil Armstrong <narmstrong@baylibre.com>
> +
> +obj-y	:= sei610.o
> diff --git a/board/amlogic/sei610/README b/board/amlogic/sei610/README
> new file mode 100644
> index 0000000000..836809ccdb
> --- /dev/null
> +++ b/board/amlogic/sei610/README
> @@ -0,0 +1,119 @@
> +U-Boot for Amlogic SEI610
> +=======================
> +
> +SEI610 is a customer board manufactured by SEI Robotics with the following
> +specifications:
> +
> + - Amlogic S905X3 ARM Cortex-A35 quad-core SoC

--------------------------------/\

Cortex-A55, will fix while applying

> + - 2GB DDR4 SDRAM
> + - 10/100 Ethernet (Internal PHY)
> + - 1 x USB 3.0 Host
> + - 1 x USB Type-C DRD
> + - 1 x FTDI USB Serial Debug Interface
> + - eMMC
> + - SDcard
> + - Infrared receiver
> + - SDIO WiFi Module
> +
> +u-boot compilation
> +==================
> +
> + > export ARCH=arm
> + > export CROSS_COMPILE=aarch64-none-elf-
> + > make sei610_defconfig
> + > make
> +
> +Image creation
> +==============
> +
> +Amlogic doesn't provide sources for the firmware and for tools needed
> +to create the bootloader image, so it is necessary to obtain them from
> +the git tree published by the board vendor:
> +
> + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
> + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
> + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
> + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
> + > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
> + > git clone https://github.com/BayLibre/u-boot.git -b buildroot-openlinux-4.9-g12a-201904 amlogic-u-boot
> + > cd amlogic-u-boot
> + > make sm1_ac200_v1_defconfig
> + > make
> + > export UBOOTDIR=$PWD
> +
> +Download the latest Amlogic Buildroot package, and extract it :
> + > wget http://openlinux2.amlogic.com:8000/ARM/filesystem/buildroot-openlinux-A113-201901.tgz
> + > tar xfz buildroot-openlinux-A113-201901.tgz buildroot-openlinux-A113-201901/bootloader
> + > export BRDIR=$PWD/buildroot-openlinux-A113-201901
> + > export FIPDIR=$BRDIR/bootloader/uboot-repo/fip
> +
> +Go back to mainline U-Boot source tree then :
> + > mkdir fip
> +
> + > wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
> + > cp $UBOOTDIR/build/scp_task/bl301.bin fip/
> + > cp $UBOOTDIR/build/board/amlogic/g12a_u200_v1/firmware/acs.bin fip/
> + > cp $BRDIR/bootloader/uboot-repo/bl2/bin/g12a/bl2.bin fip/
> + > cp $BRDIR/bootloader/uboot-repo/bl30/bin/g12a/bl30.bin fip/
> + > cp $BRDIR/bootloader/uboot-repo/bl31_1.3/bin/g12a/bl31.img fip/
> + > cp $FIPDIR/g12a/ddr3_1d.fw fip/
> + > cp $FIPDIR/g12a/ddr4_1d.fw fip/
> + > cp $FIPDIR/g12a/ddr4_2d.fw fip/
> + > cp $FIPDIR/g12a/diag_lpddr4.fw fip/
> + > cp $FIPDIR/g12a/lpddr4_1d.fw fip/
> + > cp $FIPDIR/g12a/lpddr4_2d.fw fip/
> + > cp $FIPDIR/g12a/piei.fw fip/
> + > cp u-boot.bin fip/bl33.bin
> +
> + > sh fip/blx_fix.sh \
> +	fip/bl30.bin \
> +	fip/zero_tmp \
> +	fip/bl30_zero.bin \
> +	fip/bl301.bin \
> +	fip/bl301_zero.bin \
> +	fip/bl30_new.bin \
> +	bl30
> +
> + > sh fip/blx_fix.sh \
> +	fip/bl2.bin \
> +	fip/zero_tmp \
> +	fip/bl2_zero.bin \
> +	fip/acs.bin \
> +	fip/bl21_zero.bin \
> +	fip/bl2_new.bin \
> +	bl2
> +
> + > $FIPDIR/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \
> +					--output fip/bl30_new.bin.g12a.enc \
> +					--level v3
> + > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \
> +					--output fip/bl30_new.bin.enc \
> +					--level v3 --type bl30
> + > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \
> +					--output fip/bl31.img.enc \
> +					--level v3 --type bl31
> + > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \
> +					--output fip/bl33.bin.enc \
> +					--level v3 --type bl33
> + > $FIPDIR/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \
> +					--output fip/bl2.n.bin.sig
> + > $FIPDIR/g12a/aml_encrypt_g12a --bootmk \
> +		--output fip/u-boot.bin \
> +		--bl2 fip/bl2.n.bin.sig \
> +		--bl30 fip/bl30_new.bin.enc \
> +		--bl31 fip/bl31.img.enc \
> +		--bl33 fip/bl33.bin.enc \
> +		--ddrfw1 fip/ddr4_1d.fw \
> +		--ddrfw2 fip/ddr4_2d.fw \
> +		--ddrfw3 fip/ddr3_1d.fw \
> +		--ddrfw4 fip/piei.fw \
> +		--ddrfw5 fip/lpddr4_1d.fw \
> +		--ddrfw6 fip/lpddr4_2d.fw \
> +		--ddrfw7 fip/diag_lpddr4.fw \
> +		--level v3
> +
> +and then write the image to SD with:
> +
> + > DEV=/dev/your_sd_device
> + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
> + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
> diff --git a/board/amlogic/sei610/sei610.c b/board/amlogic/sei610/sei610.c
> new file mode 100644
> index 0000000000..b17eb9ef55
> --- /dev/null
> +++ b/board/amlogic/sei610/sei610.c
> @@ -0,0 +1,26 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2016 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +#include <common.h>
> +#include <dm.h>
> +#include <env_internal.h>
> +#include <asm/io.h>
> +#include <asm/arch/axg.h>
> +#include <asm/arch/sm.h>
> +#include <asm/arch/eth.h>
> +#include <asm/arch/mem.h>
> +
> +int misc_init_r(void)
> +{
> +	meson_eth_init(PHY_INTERFACE_MODE_RMII,
> +		       MESON_USE_INTERNAL_RMII_PHY);
> +
> +	meson_generate_serial_ethaddr();
> +
> +	env_set("serial#", "AMLG12ASEI610");
> +
> +	return 0;
> +}
> diff --git a/configs/sei610_defconfig b/configs/sei610_defconfig
> new file mode 100644
> index 0000000000..89e7bd7bab
> --- /dev/null
> +++ b/configs/sei610_defconfig
> @@ -0,0 +1,76 @@
> +CONFIG_ARM=y
> +CONFIG_SYS_BOARD="sei610"
> +CONFIG_SYS_CONFIG_NAME="sei510"
> +CONFIG_ARCH_MESON=y
> +CONFIG_SYS_TEXT_BASE=0x01000000
> +CONFIG_MESON_G12A=y
> +CONFIG_NR_DRAM_BANKS=1
> +CONFIG_DEBUG_UART_BASE=0xff803000
> +CONFIG_DEBUG_UART_CLOCK=24000000
> +CONFIG_IDENT_STRING=" sei610"
> +# CONFIG_PSCI_RESET is not set
> +CONFIG_DEBUG_UART=y
> +CONFIG_OF_BOARD_SETUP=y
> +CONFIG_USE_PREBOOT=y
> +CONFIG_PREBOOT="run load_logo"
> +# CONFIG_CONSOLE_MUX is not set
> +CONFIG_MISC_INIT_R=y
> +# CONFIG_DISPLAY_CPUINFO is not set
> +# CONFIG_CMD_BDI is not set
> +# CONFIG_CMD_IMI is not set
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_GPT=y
> +# CONFIG_CMD_LOADS is not set
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_USB_MASS_STORAGE=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_BMP=y
> +CONFIG_CMD_REGULATOR=y
> +CONFIG_OF_CONTROL=y
> +CONFIG_DEFAULT_DEVICE_TREE="meson-sm1-sei610"
> +CONFIG_ENV_IS_IN_MMC=y
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_USB_FUNCTION_FASTBOOT=y
> +CONFIG_FASTBOOT_BUF_ADDR=0x6000000
> +CONFIG_FASTBOOT_FLASH=y
> +CONFIG_FASTBOOT_FLASH_MMC_DEV=2
> +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
> +CONFIG_DM_GPIO=y
> +# CONFIG_INPUT is not set
> +CONFIG_PWRSEQ=y
> +CONFIG_DM_MMC=y
> +CONFIG_MMC_MESON_GX=y
> +CONFIG_PHY_ADDR_ENABLE=y
> +CONFIG_PHY_ADDR=8
> +CONFIG_DM_ETH=y
> +CONFIG_ETH_DESIGNWARE=y
> +CONFIG_MESON_G12A_USB_PHY=y
> +CONFIG_PINCTRL=y
> +CONFIG_PINCTRL_MESON_G12A=y
> +CONFIG_POWER_DOMAIN=y
> +CONFIG_MESON_EE_POWER_DOMAIN=y
> +CONFIG_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_RESET=y
> +CONFIG_DEBUG_UART_MESON=y
> +CONFIG_DEBUG_UART_ANNOUNCE=y
> +CONFIG_DEBUG_UART_SKIP_INIT=y
> +CONFIG_MESON_SERIAL=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_XHCI_DWC3=y
> +CONFIG_USB_DWC3=y
> +CONFIG_USB_DWC3_MESON_G12A=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_VENDOR_NUM=0x18d1
> +CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
> +CONFIG_USB_GADGET_DWC2_OTG=y
> +CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
> +CONFIG_DM_VIDEO=y
> +CONFIG_SYS_WHITE_ON_BLACK=y
> +CONFIG_VIDEO_MESON=y
> +CONFIG_VIDEO_DT_SIMPLEFB=y
> +CONFIG_LZ4=y
> +CONFIG_OF_LIBFDT_OVERLAY=y
> 

^ permalink raw reply	[flat|nested] 22+ messages in thread
* Re: [PATCH 6/8] boards: amlogic: add SEI610 support
@ 2019-10-18  8:32     ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-18  8:32 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic

On 11/10/2019 17:33, Neil Armstrong wrote:
> Add support for the customer board SEI610 manufactured by SEI Robotics
> with the following specifications:
>  - Amlogic S905X3 ARM Cortex-A35 quad-core SoC

--------------------------------/\

Cortex-A55, will fix while applying

>  - 2GB DDR4 SDRAM
>  - 10/100 Ethernet (Internal PHY)
>  - 1 x USB 3.0 Host
>  - 1 x USB Type-C DRD
>  - 1 x FTDI USB Serial Debug Interface
>  - eMMC
>  - SDcard
>  - Infrared receiver
>  - SDIO WiFi Module
> 
> Like it's SEI510 counterpart, the boot flow is designed to boot
> Android AOSP built for the Yukawa Android device.
> 
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
>  board/amlogic/sei610/MAINTAINERS |   6 ++
>  board/amlogic/sei610/Makefile    |   6 ++
>  board/amlogic/sei610/README      | 119 +++++++++++++++++++++++++++++++
>  board/amlogic/sei610/sei610.c    |  26 +++++++
>  configs/sei610_defconfig         |  76 ++++++++++++++++++++
>  5 files changed, 233 insertions(+)
>  create mode 100644 board/amlogic/sei610/MAINTAINERS
>  create mode 100644 board/amlogic/sei610/Makefile
>  create mode 100644 board/amlogic/sei610/README
>  create mode 100644 board/amlogic/sei610/sei610.c
>  create mode 100644 configs/sei610_defconfig
> 
> diff --git a/board/amlogic/sei610/MAINTAINERS b/board/amlogic/sei610/MAINTAINERS
> new file mode 100644
> index 0000000000..20f12334e9
> --- /dev/null
> +++ b/board/amlogic/sei610/MAINTAINERS
> @@ -0,0 +1,6 @@
> +SEI610
> +M:	Neil Armstrong <narmstrong@baylibre.com>
> +S:	Maintained
> +L:	u-boot-amlogic@groups.io
> +F:	board/amlogic/sei610/
> +F:	configs/sei610_defconfig
> diff --git a/board/amlogic/sei610/Makefile b/board/amlogic/sei610/Makefile
> new file mode 100644
> index 0000000000..428792afea
> --- /dev/null
> +++ b/board/amlogic/sei610/Makefile
> @@ -0,0 +1,6 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +# (C) Copyright 2016 BayLibre, SAS
> +# Author: Neil Armstrong <narmstrong@baylibre.com>
> +
> +obj-y	:= sei610.o
> diff --git a/board/amlogic/sei610/README b/board/amlogic/sei610/README
> new file mode 100644
> index 0000000000..836809ccdb
> --- /dev/null
> +++ b/board/amlogic/sei610/README
> @@ -0,0 +1,119 @@
> +U-Boot for Amlogic SEI610
> +=======================
> +
> +SEI610 is a customer board manufactured by SEI Robotics with the following
> +specifications:
> +
> + - Amlogic S905X3 ARM Cortex-A35 quad-core SoC

--------------------------------/\

Cortex-A55, will fix while applying

> + - 2GB DDR4 SDRAM
> + - 10/100 Ethernet (Internal PHY)
> + - 1 x USB 3.0 Host
> + - 1 x USB Type-C DRD
> + - 1 x FTDI USB Serial Debug Interface
> + - eMMC
> + - SDcard
> + - Infrared receiver
> + - SDIO WiFi Module
> +
> +u-boot compilation
> +==================
> +
> + > export ARCH=arm
> + > export CROSS_COMPILE=aarch64-none-elf-
> + > make sei610_defconfig
> + > make
> +
> +Image creation
> +==============
> +
> +Amlogic doesn't provide sources for the firmware and for tools needed
> +to create the bootloader image, so it is necessary to obtain them from
> +the git tree published by the board vendor:
> +
> + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
> + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
> + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
> + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
> + > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
> + > git clone https://github.com/BayLibre/u-boot.git -b buildroot-openlinux-4.9-g12a-201904 amlogic-u-boot
> + > cd amlogic-u-boot
> + > make sm1_ac200_v1_defconfig
> + > make
> + > export UBOOTDIR=$PWD
> +
> +Download the latest Amlogic Buildroot package, and extract it :
> + > wget http://openlinux2.amlogic.com:8000/ARM/filesystem/buildroot-openlinux-A113-201901.tgz
> + > tar xfz buildroot-openlinux-A113-201901.tgz buildroot-openlinux-A113-201901/bootloader
> + > export BRDIR=$PWD/buildroot-openlinux-A113-201901
> + > export FIPDIR=$BRDIR/bootloader/uboot-repo/fip
> +
> +Go back to mainline U-Boot source tree then :
> + > mkdir fip
> +
> + > wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
> + > cp $UBOOTDIR/build/scp_task/bl301.bin fip/
> + > cp $UBOOTDIR/build/board/amlogic/g12a_u200_v1/firmware/acs.bin fip/
> + > cp $BRDIR/bootloader/uboot-repo/bl2/bin/g12a/bl2.bin fip/
> + > cp $BRDIR/bootloader/uboot-repo/bl30/bin/g12a/bl30.bin fip/
> + > cp $BRDIR/bootloader/uboot-repo/bl31_1.3/bin/g12a/bl31.img fip/
> + > cp $FIPDIR/g12a/ddr3_1d.fw fip/
> + > cp $FIPDIR/g12a/ddr4_1d.fw fip/
> + > cp $FIPDIR/g12a/ddr4_2d.fw fip/
> + > cp $FIPDIR/g12a/diag_lpddr4.fw fip/
> + > cp $FIPDIR/g12a/lpddr4_1d.fw fip/
> + > cp $FIPDIR/g12a/lpddr4_2d.fw fip/
> + > cp $FIPDIR/g12a/piei.fw fip/
> + > cp u-boot.bin fip/bl33.bin
> +
> + > sh fip/blx_fix.sh \
> +	fip/bl30.bin \
> +	fip/zero_tmp \
> +	fip/bl30_zero.bin \
> +	fip/bl301.bin \
> +	fip/bl301_zero.bin \
> +	fip/bl30_new.bin \
> +	bl30
> +
> + > sh fip/blx_fix.sh \
> +	fip/bl2.bin \
> +	fip/zero_tmp \
> +	fip/bl2_zero.bin \
> +	fip/acs.bin \
> +	fip/bl21_zero.bin \
> +	fip/bl2_new.bin \
> +	bl2
> +
> + > $FIPDIR/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \
> +					--output fip/bl30_new.bin.g12a.enc \
> +					--level v3
> + > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \
> +					--output fip/bl30_new.bin.enc \
> +					--level v3 --type bl30
> + > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \
> +					--output fip/bl31.img.enc \
> +					--level v3 --type bl31
> + > $FIPDIR/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \
> +					--output fip/bl33.bin.enc \
> +					--level v3 --type bl33
> + > $FIPDIR/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \
> +					--output fip/bl2.n.bin.sig
> + > $FIPDIR/g12a/aml_encrypt_g12a --bootmk \
> +		--output fip/u-boot.bin \
> +		--bl2 fip/bl2.n.bin.sig \
> +		--bl30 fip/bl30_new.bin.enc \
> +		--bl31 fip/bl31.img.enc \
> +		--bl33 fip/bl33.bin.enc \
> +		--ddrfw1 fip/ddr4_1d.fw \
> +		--ddrfw2 fip/ddr4_2d.fw \
> +		--ddrfw3 fip/ddr3_1d.fw \
> +		--ddrfw4 fip/piei.fw \
> +		--ddrfw5 fip/lpddr4_1d.fw \
> +		--ddrfw6 fip/lpddr4_2d.fw \
> +		--ddrfw7 fip/diag_lpddr4.fw \
> +		--level v3
> +
> +and then write the image to SD with:
> +
> + > DEV=/dev/your_sd_device
> + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
> + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
> diff --git a/board/amlogic/sei610/sei610.c b/board/amlogic/sei610/sei610.c
> new file mode 100644
> index 0000000000..b17eb9ef55
> --- /dev/null
> +++ b/board/amlogic/sei610/sei610.c
> @@ -0,0 +1,26 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2016 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +#include <common.h>
> +#include <dm.h>
> +#include <env_internal.h>
> +#include <asm/io.h>
> +#include <asm/arch/axg.h>
> +#include <asm/arch/sm.h>
> +#include <asm/arch/eth.h>
> +#include <asm/arch/mem.h>
> +
> +int misc_init_r(void)
> +{
> +	meson_eth_init(PHY_INTERFACE_MODE_RMII,
> +		       MESON_USE_INTERNAL_RMII_PHY);
> +
> +	meson_generate_serial_ethaddr();
> +
> +	env_set("serial#", "AMLG12ASEI610");
> +
> +	return 0;
> +}
> diff --git a/configs/sei610_defconfig b/configs/sei610_defconfig
> new file mode 100644
> index 0000000000..89e7bd7bab
> --- /dev/null
> +++ b/configs/sei610_defconfig
> @@ -0,0 +1,76 @@
> +CONFIG_ARM=y
> +CONFIG_SYS_BOARD="sei610"
> +CONFIG_SYS_CONFIG_NAME="sei510"
> +CONFIG_ARCH_MESON=y
> +CONFIG_SYS_TEXT_BASE=0x01000000
> +CONFIG_MESON_G12A=y
> +CONFIG_NR_DRAM_BANKS=1
> +CONFIG_DEBUG_UART_BASE=0xff803000
> +CONFIG_DEBUG_UART_CLOCK=24000000
> +CONFIG_IDENT_STRING=" sei610"
> +# CONFIG_PSCI_RESET is not set
> +CONFIG_DEBUG_UART=y
> +CONFIG_OF_BOARD_SETUP=y
> +CONFIG_USE_PREBOOT=y
> +CONFIG_PREBOOT="run load_logo"
> +# CONFIG_CONSOLE_MUX is not set
> +CONFIG_MISC_INIT_R=y
> +# CONFIG_DISPLAY_CPUINFO is not set
> +# CONFIG_CMD_BDI is not set
> +# CONFIG_CMD_IMI is not set
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_GPT=y
> +# CONFIG_CMD_LOADS is not set
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_USB_MASS_STORAGE=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_BMP=y
> +CONFIG_CMD_REGULATOR=y
> +CONFIG_OF_CONTROL=y
> +CONFIG_DEFAULT_DEVICE_TREE="meson-sm1-sei610"
> +CONFIG_ENV_IS_IN_MMC=y
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_USB_FUNCTION_FASTBOOT=y
> +CONFIG_FASTBOOT_BUF_ADDR=0x6000000
> +CONFIG_FASTBOOT_FLASH=y
> +CONFIG_FASTBOOT_FLASH_MMC_DEV=2
> +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
> +CONFIG_DM_GPIO=y
> +# CONFIG_INPUT is not set
> +CONFIG_PWRSEQ=y
> +CONFIG_DM_MMC=y
> +CONFIG_MMC_MESON_GX=y
> +CONFIG_PHY_ADDR_ENABLE=y
> +CONFIG_PHY_ADDR=8
> +CONFIG_DM_ETH=y
> +CONFIG_ETH_DESIGNWARE=y
> +CONFIG_MESON_G12A_USB_PHY=y
> +CONFIG_PINCTRL=y
> +CONFIG_PINCTRL_MESON_G12A=y
> +CONFIG_POWER_DOMAIN=y
> +CONFIG_MESON_EE_POWER_DOMAIN=y
> +CONFIG_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_RESET=y
> +CONFIG_DEBUG_UART_MESON=y
> +CONFIG_DEBUG_UART_ANNOUNCE=y
> +CONFIG_DEBUG_UART_SKIP_INIT=y
> +CONFIG_MESON_SERIAL=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_XHCI_DWC3=y
> +CONFIG_USB_DWC3=y
> +CONFIG_USB_DWC3_MESON_G12A=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_VENDOR_NUM=0x18d1
> +CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
> +CONFIG_USB_GADGET_DWC2_OTG=y
> +CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
> +CONFIG_DM_VIDEO=y
> +CONFIG_SYS_WHITE_ON_BLACK=y
> +CONFIG_VIDEO_MESON=y
> +CONFIG_VIDEO_DT_SIMPLEFB=y
> +CONFIG_LZ4=y
> +CONFIG_OF_LIBFDT_OVERLAY=y
> 


^ permalink raw reply	[flat|nested] 22+ messages in thread
* [U-Boot] [PATCH 0/8] amlogic: add SEI610 support
  2019-10-11 15:33 ` Neil Armstrong
@ 2019-10-18  9:22   ` Neil Armstrong
  -1 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-18  9:22 UTC (permalink / raw)
  To: u-boot

On 11/10/2019 17:33, Neil Armstrong wrote:
> Add support for the customer board SEI610 manufactured by SEI Robotics
> with the following specifications:
>  - Amlogic S905X3 ARM Cortex-A35 quad-core SoC
>  - 2GB DDR4 SDRAM
>  - 10/100 Ethernet (Internal PHY)
>  - 1 x USB 3.0 Host
>  - 1 x USB Type-C DRD
>  - 1 x FTDI USB Serial Debug Interface
>  - eMMC
>  - SDcard
>  - Infrared receiver
>  - SDIO WiFi Module
> 
> Like it's SEI510 counterpart, the boot flow is designed to boot
> Android AOSP built for the Yukawa Android device.
> 
> The SM1 SoC is very close to G12A, so it uses the same arm board code
> and reuses what was pushed for SEI510.
> 
> For that it needs to reuse the SEI510 android boot flow into
> a common flow with custom partitions for each board.
> 
> Guillaume La Roque (2):
>   configs: sei510: rework header and fix userdata size
>   configs: sei610: Add config file to fix userdata size
> 
> Neil Armstrong (6):
>   ARM: meson: add SM1 SoC id
>   mmc: meson-gx: add support for mmc-pwrseq-emmc
>   clk: meson-sm1: add compatible
>   ARM: dts: Import SEI610 DT from Linux 5.4-rc2
>   ARM: dts: meson-sm1: add U-Boot specific DT for graphics
>   boards: amlogic: add SEI610 support
> 
>  MAINTAINERS                                   |   1 +
>  arch/arm/dts/Makefile                         |   3 +-
>  ...boot.dtsi => meson-g12-common-u-boot.dtsi} |   0
>  arch/arm/dts/meson-g12a-sei510-u-boot.dtsi    |   2 +-
>  arch/arm/dts/meson-g12a-u200-u-boot.dtsi      |   2 +-
>  arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi |   2 +-
>  arch/arm/dts/meson-sm1-sei610-u-boot.dtsi     |   7 +
>  arch/arm/dts/meson-sm1-sei610.dts             | 383 ++++++++++++++++++
>  arch/arm/dts/meson-sm1.dtsi                   | 147 +++++++
>  arch/arm/mach-meson/board-info.c              |   2 +
>  board/amlogic/sei610/MAINTAINERS              |   7 +
>  board/amlogic/sei610/Makefile                 |   6 +
>  board/amlogic/sei610/README                   | 119 ++++++
>  board/amlogic/sei610/sei610.c                 |  26 ++
>  configs/sei610_defconfig                      |  76 ++++
>  drivers/clk/meson/g12a.c                      |   1 +
>  drivers/mmc/meson_gx_mmc.c                    |  51 +++
>  include/configs/meson64_android.h             | 136 +++++++
>  include/configs/sei510.h                      | 121 +-----
>  include/configs/sei610.h                      |  31 ++
>  include/dt-bindings/power/meson-sm1-power.h   |  18 +
>  21 files changed, 1018 insertions(+), 123 deletions(-)
>  rename arch/arm/dts/{meson-g12a-u-boot.dtsi => meson-g12-common-u-boot.dtsi} (100%)
>  create mode 100644 arch/arm/dts/meson-sm1-sei610-u-boot.dtsi
>  create mode 100644 arch/arm/dts/meson-sm1-sei610.dts
>  create mode 100644 arch/arm/dts/meson-sm1.dtsi
>  create mode 100644 board/amlogic/sei610/MAINTAINERS
>  create mode 100644 board/amlogic/sei610/Makefile
>  create mode 100644 board/amlogic/sei610/README
>  create mode 100644 board/amlogic/sei610/sei610.c
>  create mode 100644 configs/sei610_defconfig
>  create mode 100644 include/configs/meson64_android.h
>  create mode 100644 include/configs/sei610.h
>  create mode 100644 include/dt-bindings/power/meson-sm1-power.h
> 

Applied to u-boot-amlogic + typo fixes

^ permalink raw reply	[flat|nested] 22+ messages in thread
* Re: [PATCH 0/8] amlogic: add SEI610 support
@ 2019-10-18  9:22   ` Neil Armstrong
  0 siblings, 0 replies; 22+ messages in thread
From: Neil Armstrong @ 2019-10-18  9:22 UTC (permalink / raw)
  To: u-boot; +Cc: u-boot-amlogic

On 11/10/2019 17:33, Neil Armstrong wrote:
> Add support for the customer board SEI610 manufactured by SEI Robotics
> with the following specifications:
>  - Amlogic S905X3 ARM Cortex-A35 quad-core SoC
>  - 2GB DDR4 SDRAM
>  - 10/100 Ethernet (Internal PHY)
>  - 1 x USB 3.0 Host
>  - 1 x USB Type-C DRD
>  - 1 x FTDI USB Serial Debug Interface
>  - eMMC
>  - SDcard
>  - Infrared receiver
>  - SDIO WiFi Module
> 
> Like it's SEI510 counterpart, the boot flow is designed to boot
> Android AOSP built for the Yukawa Android device.
> 
> The SM1 SoC is very close to G12A, so it uses the same arm board code
> and reuses what was pushed for SEI510.
> 
> For that it needs to reuse the SEI510 android boot flow into
> a common flow with custom partitions for each board.
> 
> Guillaume La Roque (2):
>   configs: sei510: rework header and fix userdata size
>   configs: sei610: Add config file to fix userdata size
> 
> Neil Armstrong (6):
>   ARM: meson: add SM1 SoC id
>   mmc: meson-gx: add support for mmc-pwrseq-emmc
>   clk: meson-sm1: add compatible
>   ARM: dts: Import SEI610 DT from Linux 5.4-rc2
>   ARM: dts: meson-sm1: add U-Boot specific DT for graphics
>   boards: amlogic: add SEI610 support
> 
>  MAINTAINERS                                   |   1 +
>  arch/arm/dts/Makefile                         |   3 +-
>  ...boot.dtsi => meson-g12-common-u-boot.dtsi} |   0
>  arch/arm/dts/meson-g12a-sei510-u-boot.dtsi    |   2 +-
>  arch/arm/dts/meson-g12a-u200-u-boot.dtsi      |   2 +-
>  arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi |   2 +-
>  arch/arm/dts/meson-sm1-sei610-u-boot.dtsi     |   7 +
>  arch/arm/dts/meson-sm1-sei610.dts             | 383 ++++++++++++++++++
>  arch/arm/dts/meson-sm1.dtsi                   | 147 +++++++
>  arch/arm/mach-meson/board-info.c              |   2 +
>  board/amlogic/sei610/MAINTAINERS              |   7 +
>  board/amlogic/sei610/Makefile                 |   6 +
>  board/amlogic/sei610/README                   | 119 ++++++
>  board/amlogic/sei610/sei610.c                 |  26 ++
>  configs/sei610_defconfig                      |  76 ++++
>  drivers/clk/meson/g12a.c                      |   1 +
>  drivers/mmc/meson_gx_mmc.c                    |  51 +++
>  include/configs/meson64_android.h             | 136 +++++++
>  include/configs/sei510.h                      | 121 +-----
>  include/configs/sei610.h                      |  31 ++
>  include/dt-bindings/power/meson-sm1-power.h   |  18 +
>  21 files changed, 1018 insertions(+), 123 deletions(-)
>  rename arch/arm/dts/{meson-g12a-u-boot.dtsi => meson-g12-common-u-boot.dtsi} (100%)
>  create mode 100644 arch/arm/dts/meson-sm1-sei610-u-boot.dtsi
>  create mode 100644 arch/arm/dts/meson-sm1-sei610.dts
>  create mode 100644 arch/arm/dts/meson-sm1.dtsi
>  create mode 100644 board/amlogic/sei610/MAINTAINERS
>  create mode 100644 board/amlogic/sei610/Makefile
>  create mode 100644 board/amlogic/sei610/README
>  create mode 100644 board/amlogic/sei610/sei610.c
>  create mode 100644 configs/sei610_defconfig
>  create mode 100644 include/configs/meson64_android.h
>  create mode 100644 include/configs/sei610.h
>  create mode 100644 include/dt-bindings/power/meson-sm1-power.h
> 

Applied to u-boot-amlogic + typo fixes

^ permalink raw reply	[flat|nested] 22+ messages in thread
end of thread, other threads:[~2019-10-18  9:22 UTC | newest]

Thread overview: 22+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-11 15:33 [U-Boot] [PATCH 0/8] amlogic: add SEI610 support Neil Armstrong
2019-10-11 15:33 ` Neil Armstrong
2019-10-11 15:33 ` [U-Boot] [PATCH 1/8] ARM: meson: add SM1 SoC id Neil Armstrong
2019-10-11 15:33   ` Neil Armstrong
2019-10-11 15:33 ` [U-Boot] [PATCH 2/8] mmc: meson-gx: add support for mmc-pwrseq-emmc Neil Armstrong
2019-10-11 15:33   ` Neil Armstrong
2019-10-11 15:33 ` [U-Boot] [PATCH 3/8] clk: meson-sm1: add compatible Neil Armstrong
2019-10-11 15:33   ` Neil Armstrong
2019-10-11 15:33 ` [U-Boot] [PATCH 4/8] ARM: dts: Import SEI610 DT from Linux 5.4-rc2 Neil Armstrong
2019-10-11 15:33   ` Neil Armstrong
2019-10-11 15:33 ` [U-Boot] [PATCH 5/8] ARM: dts: meson-sm1: add U-Boot specific DT for graphics Neil Armstrong
2019-10-11 15:33   ` Neil Armstrong
2019-10-11 15:33 ` [U-Boot] [PATCH 6/8] boards: amlogic: add SEI610 support Neil Armstrong
2019-10-11 15:33   ` Neil Armstrong
2019-10-18  8:32   ` [U-Boot] " Neil Armstrong
2019-10-18  8:32     ` Neil Armstrong
2019-10-11 15:33 ` [U-Boot] [PATCH 7/8] configs: sei510: rework header and fix userdata size Neil Armstrong
2019-10-11 15:33   ` Neil Armstrong
2019-10-11 15:33 ` [U-Boot] [PATCH 8/8] configs: sei610: Add config file to " Neil Armstrong
2019-10-11 15:33   ` Neil Armstrong
2019-10-18  9:22 ` [U-Boot] [PATCH 0/8] amlogic: add SEI610 support Neil Armstrong
2019-10-18  9:22   ` Neil Armstrong

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.