[PATCH v8 0/6] Enable Transcoder port sync for Tiled displays

All of lore.kernel.org
 help / color / mirror / Atom feed

* [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays
@ 2019-10-15 23:05 Manasi Navare
  2019-10-15 23:05 ` [PATCH v8 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
                   ` (13 more replies)
  0 siblings, 14 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-15 23:05 UTC (permalink / raw)
  To: intel-gfx

This set of patches enables transcoder port sync to synchronize tiled displays
across multiple SST DP ports using the master-slave model.
This has been tested with kms_dp_tiled_display.c IGT test which validates
the page flip synchronization.

This set of patches addresses the final set of comments from Ville
and Maarten.

Manasi Navare (6):
  drm/i915/display/icl: Save Master transcoder in slave's crtc_state for
    Transcoder Port Sync
  drm/i915/display/icl: Enable TRANSCODER PORT SYNC for tiled displays
    across separate ports
  drm/i915/display/icl: HW state readout for transcoder port sync config
  drm/i915/display/icl: Enable master-slaves in trans port sync
  drm/i915/display/icl: Disable transcoder port sync as part of
    crtc_disable() sequence
  drm/i915/display/icl: In port sync mode disable slaves first then
    master

 drivers/gpu/drm/i915/display/intel_ddi.c      |   3 +-
 drivers/gpu/drm/i915/display/intel_display.c  | 428 +++++++++++++++++-
 drivers/gpu/drm/i915/display/intel_display.h  |   4 +
 .../drm/i915/display/intel_display_types.h    |   6 +
 4 files changed, 431 insertions(+), 10 deletions(-)

-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v8 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
@ 2019-10-15 23:05 ` Manasi Navare
  2019-10-15 23:24   ` [PATCH v9 " Manasi Navare
  2019-10-15 23:05 ` [PATCH v8 2/6] drm/i915/display/icl: Enable TRANSCODER PORT SYNC for tiled displays across separate ports Manasi Navare
                   ` (12 subsequent siblings)
  13 siblings, 1 reply; 18+ messages in thread
From: Manasi Navare @ 2019-10-15 23:05 UTC (permalink / raw)
  To: intel-gfx; +Cc: Daniel Vetter

In case of tiled displays when the two tiles are sent across two CRTCs
over two separate DP SST connectors, we need a mechanism to synchronize
the two CRTCs and their corresponding transcoders.
So use the master-slave mode where there is one master corresponding
to last horizontal and vertical tile that needs to be genlocked with
all other slave tiles.
This patch identifies saves the master transcoder in all the slave
CRTC states. This is needed to select the master CRTC/transcoder
while configuring transcoder port sync for the corresponding slaves.

v5:
* Address Ville's comments
* Just pass crtc_state, no need to check GEN (Ville)
v4:
* Rebase
v3:
* Use master_tramscoder instead of master_crtc for valid
HW state readouts (Ville)
v2:
* Move this to intel_mode_set_pipe_config(Jani N, Ville)
* Use slave_bitmask to save associated slaves in master crtc state (Ville)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c  | 118 ++++++++++++++++++
 drivers/gpu/drm/i915/display/intel_display.h  |   2 +
 .../drm/i915/display/intel_display_types.h    |   6 +
 3 files changed, 126 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index d1b74e8a37fe..ed6198fce537 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -519,6 +519,20 @@ needs_modeset(const struct intel_crtc_state *state)
 	return drm_atomic_crtc_needs_modeset(&state->base);
 }
 
+bool
+is_trans_port_sync_mode(const struct intel_crtc_state *crtc_state)
+{
+	return (crtc_state->master_transcoder != INVALID_TRANSCODER ||
+		crtc_state->sync_mode_slaves_mask);
+}
+
+static bool
+is_trans_port_sync_master(const struct intel_crtc_state *crtc_state)
+{
+	return (crtc_state->master_transcoder == INVALID_TRANSCODER &&
+		crtc_state->sync_mode_slaves_mask);
+}
+
 /*
  * Platform specific helpers to calculate the port PLL loopback- (clock.m),
  * and post-divider (clock.p) values, pre- (clock.vco) and post-divided fast
@@ -11784,6 +11798,91 @@ static bool c8_planes_changed(const struct intel_crtc_state *new_crtc_state)
 	return !old_crtc_state->c8_planes != !new_crtc_state->c8_planes;
 }
 
+static int icl_add_sync_mode_crtcs(struct intel_crtc_state *crtc_state)
+{
+	struct drm_crtc *crtc = crtc_state->base.crtc;
+	struct intel_atomic_state *state = to_intel_atomic_state(crtc_state->base.state);
+	struct drm_i915_private *dev_priv = to_i915(crtc_state->base.crtc->dev);
+	struct drm_connector *master_connector, *connector;
+	struct drm_connector_state *connector_state;
+	struct drm_connector_list_iter conn_iter;
+	struct drm_crtc *master_crtc = NULL;
+	struct drm_crtc_state *master_crtc_state;
+	struct intel_crtc_state *master_pipe_config;
+	int i, tile_group_id;
+
+	if (INTEL_GEN(dev_priv) < 11)
+		return 0;
+
+	/*
+	 * In case of tiled displays there could be one or more slaves but there is
+	 * only one master. Lets make the CRTC used by the connector corresponding
+	 * to the last horizonal and last vertical tile a master/genlock CRTC.
+	 * All the other CRTCs corresponding to other tiles of the same Tile group
+	 * are the slave CRTCs and hold a pointer to their genlock CRTC.
+	 */
+	for_each_new_connector_in_state(&state->base, connector, connector_state, i) {
+		if (connector_state->crtc != crtc)
+			continue;
+		if (!connector->has_tile)
+			continue;
+		if (crtc_state->base.mode.hdisplay != connector->tile_h_size ||
+		    crtc_state->base.mode.vdisplay != connector->tile_v_size)
+			return 0;
+		if (connector->tile_h_loc == connector->num_h_tile - 1 &&
+		    connector->tile_v_loc == connector->num_v_tile - 1)
+			continue;
+		crtc_state->sync_mode_slaves_mask = 0;
+		tile_group_id = connector->tile_group->id;
+		drm_connector_list_iter_begin(&dev_priv->drm, &conn_iter);
+		drm_for_each_connector_iter(master_connector, &conn_iter) {
+			struct drm_connector_state *master_conn_state = NULL;
+
+			if (!master_connector->has_tile)
+				continue;
+			if (master_connector->tile_h_loc != master_connector->num_h_tile - 1 ||
+			    master_connector->tile_v_loc != master_connector->num_v_tile - 1)
+				continue;
+			if (master_connector->tile_group->id != tile_group_id)
+				continue;
+
+			master_conn_state = drm_atomic_get_connector_state(&state->base,
+									   master_connector);
+			if (IS_ERR(master_conn_state)) {
+				drm_connector_list_iter_end(&conn_iter);
+				return PTR_ERR(master_conn_state);
+			}
+			if (master_conn_state->crtc) {
+				master_crtc = master_conn_state->crtc;
+				break;
+			}
+		}
+		drm_connector_list_iter_end(&conn_iter);
+
+		if (!master_crtc) {
+			DRM_DEBUG_KMS("Could not find Master CRTC for Slave CRTC %d\n",
+				      connector_state->crtc->base.id);
+			return -EINVAL;
+		}
+
+		master_crtc_state = drm_atomic_get_crtc_state(&state->base,
+							      master_crtc);
+		if (IS_ERR(master_crtc_state))
+			return PTR_ERR(master_crtc_state);
+
+		master_pipe_config = to_intel_crtc_state(master_crtc_state);
+		crtc_state->master_transcoder = master_pipe_config->cpu_transcoder;
+		master_pipe_config->sync_mode_slaves_mask |=
+			BIT(crtc_state->cpu_transcoder);
+		DRM_DEBUG_KMS("Master Transcoder = %s added for Slave CRTC = %d, slave transcoder bitmask = %d\n",
+			      transcoder_name(crtc_state->master_transcoder),
+			      crtc_state->base.crtc->base.id,
+			      master_pipe_config->sync_mode_slaves_mask);
+	}
+
+	return 0;
+}
+
 static int intel_crtc_atomic_check(struct drm_crtc *_crtc,
 				   struct drm_crtc_state *_crtc_state)
 {
@@ -12287,6 +12386,13 @@ clear_intel_crtc_state(struct intel_crtc_state *crtc_state)
 	if (IS_G4X(dev_priv) ||
 	    IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
 		saved_state->wm = crtc_state->wm;
+	/*
+	 * Save the slave bitmask which gets filled for master crtc state during
+	 * slave atomic check call.
+	 */
+	if (is_trans_port_sync_master(crtc_state))
+		saved_state->sync_mode_slaves_mask =
+			crtc_state->sync_mode_slaves_mask;
 
 	/* Keep base drm_crtc_state intact, only clear our extended struct */
 	BUILD_BUG_ON(offsetof(struct intel_crtc_state, base));
@@ -12380,6 +12486,15 @@ intel_modeset_pipe_config(struct intel_crtc_state *pipe_config)
 	drm_mode_set_crtcinfo(&pipe_config->base.adjusted_mode,
 			      CRTC_STEREO_DOUBLE);
 
+	/* Set the crtc_state defaults for trans_port_sync */
+	pipe_config->master_transcoder = INVALID_TRANSCODER;
+	ret = icl_add_sync_mode_crtcs(pipe_config);
+	if (ret) {
+		DRM_DEBUG_KMS("Cannot assign Sync Mode CRTCs: %d\n",
+			      ret);
+		return ret;
+	}
+
 	/* Pass our mode to the connectors and the CRTC to give them a chance to
 	 * adjust it according to limitations or connector properties, and also
 	 * a chance to reject the mode entirely.
@@ -12895,6 +13010,9 @@ intel_pipe_config_compare(const struct intel_crtc_state *current_config,
 	PIPE_CONF_CHECK_INFOFRAME(hdmi);
 	PIPE_CONF_CHECK_INFOFRAME(drm);
 
+	PIPE_CONF_CHECK_I(sync_mode_slaves_mask);
+	PIPE_CONF_CHECK_I(master_transcoder);
+
 #undef PIPE_CONF_CHECK_X
 #undef PIPE_CONF_CHECK_I
 #undef PIPE_CONF_CHECK_BOOL
diff --git a/drivers/gpu/drm/i915/display/intel_display.h b/drivers/gpu/drm/i915/display/intel_display.h
index bc2cf4bec0e8..761c79ee66a5 100644
--- a/drivers/gpu/drm/i915/display/intel_display.h
+++ b/drivers/gpu/drm/i915/display/intel_display.h
@@ -93,6 +93,7 @@ enum pipe {
 #define pipe_name(p) ((p) + 'A')
 
 enum transcoder {
+	INVALID_TRANSCODER = -1,
 	/*
 	 * The following transcoders have a 1:1 transcoder -> pipe mapping,
 	 * keep their values fixed: the code assumes that TRANSCODER_A=0, the
@@ -461,6 +462,7 @@ enum drm_mode_status
 intel_mode_valid_max_plane_size(struct drm_i915_private *dev_priv,
 				const struct drm_display_mode *mode);
 enum phy intel_port_to_phy(struct drm_i915_private *i915, enum port port);
+bool is_trans_port_sync_mode(const struct intel_crtc_state *state);
 
 void intel_plane_destroy(struct drm_plane *plane);
 void i830_enable_pipe(struct drm_i915_private *dev_priv, enum pipe pipe);
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index 40390d855815..8358152e403e 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -991,6 +991,12 @@ struct intel_crtc_state {
 
 	/* Forward Error correction State */
 	bool fec_enable;
+
+	/* Pointer to master transcoder in case of tiled displays */
+	enum transcoder master_transcoder;
+
+	/* Bitmask to indicate slaves attached */
+	u8 sync_mode_slaves_mask;
 };
 
 struct intel_crtc {
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v8 2/6] drm/i915/display/icl: Enable TRANSCODER PORT SYNC for tiled displays across separate ports
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
  2019-10-15 23:05 ` [PATCH v8 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
@ 2019-10-15 23:05 ` Manasi Navare
  2019-10-15 23:05 ` [PATCH v8 3/6] drm/i915/display/icl: HW state readout for transcoder port sync config Manasi Navare
                   ` (11 subsequent siblings)
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-15 23:05 UTC (permalink / raw)
  To: intel-gfx; +Cc: Jani Nikula, Daniel Vetter

In case of tiled displays where different tiles are displayed across
different ports, we need to synchronize the transcoders involved.
This patch implements the transcoder port sync feature for
synchronizing one master transcoder with one or more slave
transcoders. This is only enbaled in slave transcoder
and the master transcoder is unaware that it is operating
in this mode.
This has been tested with tiled display connected to ICL.

v7:
* Rebase on Maarten's patches
v6:
* Use master_trans +1 and address missing trans_edp case (Ville)
v5:
* Add TRANSCODER_D case and MISSING_CASE (Maarten)
v4:
Rebase
v3:
* Check of DP_MST moved to atomic_check (Maarten)
v2:
* Do not use RMW, just write to the register in commit (Jani N)

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c | 33 ++++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index ed6198fce537..b547f28e1971 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -4413,6 +4413,36 @@ static void icl_set_pipe_chicken(struct intel_crtc *crtc)
 	I915_WRITE(PIPE_CHICKEN(pipe), tmp);
 }
 
+static void icl_enable_trans_port_sync(const struct intel_crtc_state *crtc_state)
+{
+	struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
+	struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
+	u32 trans_ddi_func_ctl2_val;
+	u8 master_select;
+
+	/*
+	 * Configure the master select and enable Transcoder Port Sync for
+	 * Slave CRTCs transcoder.
+	 */
+	if (crtc_state->master_transcoder == INVALID_TRANSCODER)
+		return;
+
+	if (crtc_state->master_transcoder == TRANSCODER_EDP)
+		master_select = 0;
+	else
+		master_select = crtc_state->master_transcoder + 1;
+
+	/* Set the master select bits for Tranascoder Port Sync */
+	trans_ddi_func_ctl2_val = (PORT_SYNC_MODE_MASTER_SELECT(master_select) &
+				   PORT_SYNC_MODE_MASTER_SELECT_MASK) <<
+		PORT_SYNC_MODE_MASTER_SELECT_SHIFT;
+	/* Enable Transcoder Port Sync */
+	trans_ddi_func_ctl2_val |= PORT_SYNC_MODE_ENABLE;
+
+	I915_WRITE(TRANS_DDI_FUNC_CTL2(crtc_state->cpu_transcoder),
+		   trans_ddi_func_ctl2_val);
+}
+
 static void intel_fdi_normal_train(struct intel_crtc *crtc)
 {
 	struct drm_device *dev = crtc->base.dev;
@@ -6437,6 +6467,9 @@ static void haswell_crtc_enable(struct intel_crtc_state *pipe_config,
 	if (!transcoder_is_dsi(cpu_transcoder))
 		intel_set_pipe_timings(pipe_config);
 
+	if (INTEL_GEN(dev_priv) >= 11)
+		icl_enable_trans_port_sync(pipe_config);
+
 	intel_set_pipe_src_size(pipe_config);
 
 	if (cpu_transcoder != TRANSCODER_EDP &&
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v8 3/6] drm/i915/display/icl: HW state readout for transcoder port sync config
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
  2019-10-15 23:05 ` [PATCH v8 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
  2019-10-15 23:05 ` [PATCH v8 2/6] drm/i915/display/icl: Enable TRANSCODER PORT SYNC for tiled displays across separate ports Manasi Navare
@ 2019-10-15 23:05 ` Manasi Navare
  2019-10-15 23:05 ` [PATCH v8 4/6] drm/i915/display/icl: Enable master-slaves in trans port sync Manasi Navare
                   ` (10 subsequent siblings)
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-15 23:05 UTC (permalink / raw)
  To: intel-gfx; +Cc: Jani Nikula

After the state is committed, we readout the HW registers and compare
the HW state with the SW state that we just committed.
For Transcdoer port sync, we add master_transcoder and the
salves bitmask to the crtc_state, hence we need to read those during
the HW state readout to avoid pipe state mismatch.

v9:
* Initialize master_transcoder = INVALID at get config (Ville)
v8:
* Use master_select -1, address TRANS_EDP case (Ville)
* Rename master_transcoder to _readout (Lucas)
v7:
* NDont read HW state for DSI
v6:
* Go through both parts of HW readout (Maarten)
* Add a WARN if the same trans configured as
master and slave (Ville, Maarten)
v5:
* Add return INVALID in defaut case (Maarten)
v4:
* Get power domains in master loop for get_config (Ville)
v3:
* Add TRANSCODER_D (Maarten)
* v3 Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
v2:
* Add Transcoder_D and MISSING_CASE (Maarten)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c | 59 ++++++++++++++++++++
 1 file changed, 59 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index b547f28e1971..3f40fa2d8278 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -10440,6 +10440,59 @@ static void haswell_get_ddi_port_state(struct intel_crtc *crtc,
 	}
 }
 
+static enum transcoder transcoder_master_readout(struct drm_i915_private *dev_priv,
+						 enum transcoder cpu_transcoder)
+{
+	u32 trans_port_sync, master_select;
+
+	trans_port_sync = I915_READ(TRANS_DDI_FUNC_CTL2(cpu_transcoder));
+
+	if ((trans_port_sync & PORT_SYNC_MODE_ENABLE) == 0)
+		return INVALID_TRANSCODER;
+
+	master_select = trans_port_sync &
+			PORT_SYNC_MODE_MASTER_SELECT_MASK;
+	if (master_select == 0)
+		return TRANSCODER_EDP;
+	else
+		return master_select - 1;
+}
+
+static void icelake_get_trans_port_sync_config(struct intel_crtc_state *crtc_state)
+{
+	struct drm_i915_private *dev_priv = to_i915(crtc_state->base.crtc->dev);
+	u32 transcoders;
+	enum transcoder cpu_transcoder;
+
+	crtc_state->master_transcoder = transcoder_master_readout(dev_priv,
+								  crtc_state->cpu_transcoder);
+
+	transcoders = BIT(TRANSCODER_A) |
+		BIT(TRANSCODER_B) |
+		BIT(TRANSCODER_C) |
+		BIT(TRANSCODER_D);
+	for_each_cpu_transcoder_masked(dev_priv, cpu_transcoder, transcoders) {
+		enum intel_display_power_domain power_domain;
+		intel_wakeref_t trans_wakeref;
+
+		power_domain = POWER_DOMAIN_TRANSCODER(cpu_transcoder);
+		trans_wakeref = intel_display_power_get_if_enabled(dev_priv,
+								   power_domain);
+
+		if (!trans_wakeref)
+			continue;
+
+		if (transcoder_master_readout(dev_priv, cpu_transcoder) ==
+		    crtc_state->cpu_transcoder)
+			crtc_state->sync_mode_slaves_mask |= BIT(cpu_transcoder);
+
+		intel_display_power_put(dev_priv, power_domain, trans_wakeref);
+	}
+
+	WARN_ON(crtc_state->master_transcoder != INVALID_TRANSCODER &&
+		crtc_state->sync_mode_slaves_mask);
+}
+
 static bool haswell_get_pipe_config(struct intel_crtc *crtc,
 				    struct intel_crtc_state *pipe_config)
 {
@@ -10449,6 +10502,8 @@ static bool haswell_get_pipe_config(struct intel_crtc *crtc,
 	u64 power_domain_mask;
 	bool active;
 
+	pipe_config->master_transcoder = INVALID_TRANSCODER;
+
 	intel_crtc_init_scalers(crtc, pipe_config);
 
 	power_domain = POWER_DOMAIN_PIPE(crtc->pipe);
@@ -10559,6 +10614,10 @@ static bool haswell_get_pipe_config(struct intel_crtc *crtc,
 		pipe_config->pixel_multiplier = 1;
 	}
 
+	if (INTEL_GEN(dev_priv) >= 11 &&
+	    !transcoder_is_dsi(pipe_config->cpu_transcoder))
+		icelake_get_trans_port_sync_config(pipe_config);
+
 out:
 	for_each_power_domain(power_domain, power_domain_mask)
 		intel_display_power_put(dev_priv,
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v8 4/6] drm/i915/display/icl: Enable master-slaves in trans port sync
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (2 preceding siblings ...)
  2019-10-15 23:05 ` [PATCH v8 3/6] drm/i915/display/icl: HW state readout for transcoder port sync config Manasi Navare
@ 2019-10-15 23:05 ` Manasi Navare
  2019-10-15 23:05 ` [PATCH v8 5/6] drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence Manasi Navare
                   ` (9 subsequent siblings)
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-15 23:05 UTC (permalink / raw)
  To: intel-gfx; +Cc: Daniel Vetter

As per the display enable sequence, we need to follow the enable sequence
for slaves first with DP_TP_CTL set to Idle and configure the transcoder
port sync register to select the corersponding master, then follow the
enable sequence for master leaving DP_TP_CTL to idle.
At this point the transcoder port sync mode is configured and enabled
and the Vblanks of both ports are synchronized so then set DP_TP_CTL
for the slave and master to Normal and do post crtc enable updates.

v8:
* Rebase on Maarten's patches (Manasi)
v7:
* Use ffs(slaves) to get slave crtc (Ville)
v6:
* Modeset implies active_changed, remove one condition (Maarten)
v5:
* Fix checkpatch warning (Manasi)
v4:
* Reuse skl_commit_modeset_enables() hook (Maarten)
* Obtain slave crtc and states from master (Maarten)
v3:
* Rebase on drm-tip (Manasi)
v2:
* Create a icl_update_crtcs hook (Maarten, Danvet)
* This sequence only for CRTCs in trans port sync mode (Maarten)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_ddi.c     |   3 +-
 drivers/gpu/drm/i915/display/intel_display.c | 136 ++++++++++++++++++-
 drivers/gpu/drm/i915/display/intel_display.h |   2 +
 3 files changed, 137 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index 6c1315c7bcde..b96091800662 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -3571,7 +3571,8 @@ static void hsw_ddi_pre_enable_dp(struct intel_encoder *encoder,
 					      true);
 	intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
 	intel_dp_start_link_train(intel_dp);
-	if (port != PORT_A || INTEL_GEN(dev_priv) >= 9)
+	if ((port != PORT_A || INTEL_GEN(dev_priv) >= 9) &&
+	    !is_trans_port_sync_mode(crtc_state))
 		intel_dp_stop_link_train(intel_dp);
 
 	intel_ddi_enable_fec(encoder, crtc_state);
diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index 3f40fa2d8278..bde142607dac 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -14008,6 +14008,18 @@ static void intel_update_crtc(struct intel_crtc *crtc,
 		intel_crtc_arm_fifo_underrun(crtc, new_crtc_state);
 }
 
+static struct intel_crtc *intel_get_slave_crtc(const struct intel_crtc_state *new_crtc_state)
+{
+	struct drm_i915_private *dev_priv = to_i915(new_crtc_state->base.crtc->dev);
+	enum transcoder slave_transcoder;
+
+	WARN_ON(!is_power_of_2(new_crtc_state->sync_mode_slaves_mask));
+
+	slave_transcoder = ffs(new_crtc_state->sync_mode_slaves_mask) - 1;
+	return intel_get_crtc_for_pipe(dev_priv,
+				       (enum pipe)slave_transcoder);
+}
+
 static void intel_old_crtc_state_disables(struct intel_atomic_state *state,
 					  struct intel_crtc_state *old_crtc_state,
 					  struct intel_crtc_state *new_crtc_state,
@@ -14086,6 +14098,113 @@ static void intel_commit_modeset_enables(struct intel_atomic_state *state)
 	}
 }
 
+static void intel_crtc_enable_trans_port_sync(struct intel_crtc *crtc,
+					      struct intel_atomic_state *state,
+					      struct intel_crtc_state *new_crtc_state)
+{
+	struct drm_i915_private *dev_priv = to_i915(state->base.dev);
+
+	update_scanline_offset(new_crtc_state);
+	dev_priv->display.crtc_enable(new_crtc_state, state);
+	intel_crtc_enable_pipe_crc(crtc);
+}
+
+static void intel_set_dp_tp_ctl_normal(struct intel_crtc *crtc,
+				       struct intel_atomic_state *state)
+{
+	struct drm_connector_state *conn_state;
+	struct drm_connector *conn;
+	struct intel_dp *intel_dp;
+	int i;
+
+	for_each_new_connector_in_state(&state->base, conn, conn_state, i) {
+		if (conn_state->crtc == &crtc->base)
+			break;
+	}
+	intel_dp = enc_to_intel_dp(&intel_attached_encoder(conn)->base);
+	intel_dp_stop_link_train(intel_dp);
+}
+
+static void intel_post_crtc_enable_updates(struct intel_crtc *crtc,
+					   struct intel_atomic_state *state)
+{
+	struct intel_crtc_state *new_crtc_state =
+		intel_atomic_get_new_crtc_state(state, crtc);
+	struct intel_crtc_state *old_crtc_state =
+		intel_atomic_get_old_crtc_state(state, crtc);
+	struct intel_plane_state *new_plane_state =
+		intel_atomic_get_new_plane_state(state,
+						 to_intel_plane(crtc->base.primary));
+	bool modeset = needs_modeset(new_crtc_state);
+
+	if (new_crtc_state->update_pipe && !new_crtc_state->enable_fbc)
+		intel_fbc_disable(crtc);
+	else if (new_plane_state)
+		intel_fbc_enable(crtc, new_crtc_state, new_plane_state);
+
+	/* Perform vblank evasion around commit operation */
+	intel_pipe_update_start(new_crtc_state);
+	commit_pipe_config(state, old_crtc_state, new_crtc_state);
+	skl_update_planes_on_crtc(state, crtc);
+	intel_pipe_update_end(new_crtc_state);
+
+	/*
+	 * We usually enable FIFO underrun interrupts as part of the
+	 * CRTC enable sequence during modesets.  But when we inherit a
+	 * valid pipe configuration from the BIOS we need to take care
+	 * of enabling them on the CRTC's first fastset.
+	 */
+	if (new_crtc_state->update_pipe && !modeset &&
+	    old_crtc_state->base.mode.private_flags & I915_MODE_FLAG_INHERITED)
+		intel_crtc_arm_fifo_underrun(crtc, new_crtc_state);
+}
+
+static void intel_update_trans_port_sync_crtcs(struct intel_crtc *crtc,
+					       struct intel_atomic_state *state,
+					       struct intel_crtc_state *old_crtc_state,
+					       struct intel_crtc_state *new_crtc_state)
+{
+	struct intel_crtc *slave_crtc = intel_get_slave_crtc(new_crtc_state);
+	struct intel_crtc_state *new_slave_crtc_state =
+		intel_atomic_get_new_crtc_state(state, slave_crtc);
+	struct intel_crtc_state *old_slave_crtc_state =
+		intel_atomic_get_old_crtc_state(state, slave_crtc);
+
+	WARN_ON(!slave_crtc || !new_slave_crtc_state ||
+		!old_slave_crtc_state);
+
+	DRM_DEBUG_KMS("Updating Transcoder Port Sync Master CRTC = %d %s and Slave CRTC %d %s\n",
+		      crtc->base.base.id, crtc->base.name, slave_crtc->base.base.id,
+		      slave_crtc->base.name);
+
+	/* Enable seq for slave with with DP_TP_CTL left Idle until the
+	 * master is ready
+	 */
+	intel_crtc_enable_trans_port_sync(slave_crtc,
+					  state,
+					  new_slave_crtc_state);
+
+	/* Enable seq for master with with DP_TP_CTL left Idle */
+	intel_crtc_enable_trans_port_sync(crtc,
+					  state,
+					  new_crtc_state);
+
+	/* Set Slave's DP_TP_CTL to Normal */
+	intel_set_dp_tp_ctl_normal(slave_crtc,
+				   state);
+
+	/* Set Master's DP_TP_CTL To Normal */
+	usleep_range(200, 400);
+	intel_set_dp_tp_ctl_normal(crtc,
+				   state);
+
+	/* Now do the post crtc enable for all master and slaves */
+	intel_post_crtc_enable_updates(slave_crtc,
+				       state);
+	intel_post_crtc_enable_updates(crtc,
+				       state);
+}
+
 static void skl_commit_modeset_enables(struct intel_atomic_state *state)
 {
 	struct drm_i915_private *dev_priv = to_i915(state->base.dev);
@@ -14120,6 +14239,7 @@ static void skl_commit_modeset_enables(struct intel_atomic_state *state)
 		for_each_oldnew_intel_crtc_in_state(state, crtc, old_crtc_state, new_crtc_state, i) {
 			bool vbl_wait = false;
 			unsigned int cmask = drm_crtc_mask(&crtc->base);
+			bool modeset = needs_modeset(new_crtc_state);
 
 			pipe = crtc->pipe;
 
@@ -14142,12 +14262,22 @@ static void skl_commit_modeset_enables(struct intel_atomic_state *state)
 			 */
 			if (!skl_ddb_entry_equal(&new_crtc_state->wm.skl.ddb,
 						 &old_crtc_state->wm.skl.ddb) &&
-			    !new_crtc_state->base.active_changed &&
+			    !modeset &&
 			    state->wm_results.dirty_pipes != updated)
 				vbl_wait = true;
 
-			intel_update_crtc(crtc, state, old_crtc_state,
-					  new_crtc_state);
+			if (modeset && is_trans_port_sync_mode(new_crtc_state)) {
+				if (is_trans_port_sync_master(new_crtc_state))
+					intel_update_trans_port_sync_crtcs(crtc,
+									   state,
+									   old_crtc_state,
+									   new_crtc_state);
+				else
+					continue;
+			} else {
+				intel_update_crtc(crtc, state, old_crtc_state,
+						  new_crtc_state);
+			}
 
 			if (vbl_wait)
 				intel_wait_for_vblank(dev_priv, pipe);
diff --git a/drivers/gpu/drm/i915/display/intel_display.h b/drivers/gpu/drm/i915/display/intel_display.h
index 761c79ee66a5..afb8eab0d940 100644
--- a/drivers/gpu/drm/i915/display/intel_display.h
+++ b/drivers/gpu/drm/i915/display/intel_display.h
@@ -27,6 +27,7 @@
 
 #include <drm/drm_util.h>
 #include <drm/i915_drm.h>
+#include "intel_dp_link_training.h"
 
 enum link_m_n_set;
 struct dpll;
@@ -54,6 +55,7 @@ struct intel_plane;
 struct intel_plane_state;
 struct intel_remapped_info;
 struct intel_rotation_info;
+struct intel_crtc_state;
 
 enum i915_gpio {
 	GPIOA,
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v8 5/6] drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (3 preceding siblings ...)
  2019-10-15 23:05 ` [PATCH v8 4/6] drm/i915/display/icl: Enable master-slaves in trans port sync Manasi Navare
@ 2019-10-15 23:05 ` Manasi Navare
  2019-10-15 23:05 ` [PATCH v8 6/6] drm/i915/display/icl: In port sync mode disable slaves first then master Manasi Navare
                   ` (8 subsequent siblings)
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-15 23:05 UTC (permalink / raw)
  To: intel-gfx; +Cc: Jani Nikula

This clears the transcoder port sync bits of the TRANS_DDI_FUNC_CTL2
register during crtc_disable().

v3:
* Rebase on maarten's patches
v2:
* Directly write the trans_port_sync reg value (Maarten)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c | 22 ++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index bde142607dac..c7dbba237185 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -4443,6 +4443,25 @@ static void icl_enable_trans_port_sync(const struct intel_crtc_state *crtc_state
 		   trans_ddi_func_ctl2_val);
 }
 
+static void icl_disable_transcoder_port_sync(const struct intel_crtc_state *old_crtc_state)
+{
+	struct intel_crtc *crtc = to_intel_crtc(old_crtc_state->base.crtc);
+	struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
+	i915_reg_t reg;
+	u32 trans_ddi_func_ctl2_val;
+
+	if (old_crtc_state->master_transcoder == INVALID_TRANSCODER)
+		return;
+
+	DRM_DEBUG_KMS("Disabling Transcoder Port Sync on Slave Transcoder %s\n",
+		      transcoder_name(old_crtc_state->cpu_transcoder));
+
+	reg = TRANS_DDI_FUNC_CTL2(old_crtc_state->cpu_transcoder);
+	trans_ddi_func_ctl2_val = ~(PORT_SYNC_MODE_ENABLE |
+				    PORT_SYNC_MODE_MASTER_SELECT_MASK);
+	I915_WRITE(reg, trans_ddi_func_ctl2_val);
+}
+
 static void intel_fdi_normal_train(struct intel_crtc *crtc)
 {
 	struct drm_device *dev = crtc->base.dev;
@@ -6648,6 +6667,9 @@ static void haswell_crtc_disable(struct intel_crtc_state *old_crtc_state,
 	if (intel_crtc_has_type(old_crtc_state, INTEL_OUTPUT_DP_MST))
 		intel_ddi_set_vc_payload_alloc(old_crtc_state, false);
 
+	if (INTEL_GEN(dev_priv) >= 11)
+		icl_disable_transcoder_port_sync(old_crtc_state);
+
 	if (!transcoder_is_dsi(cpu_transcoder))
 		intel_ddi_disable_transcoder_func(old_crtc_state);
 
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v8 6/6] drm/i915/display/icl: In port sync mode disable slaves first then master
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (4 preceding siblings ...)
  2019-10-15 23:05 ` [PATCH v8 5/6] drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence Manasi Navare
@ 2019-10-15 23:05 ` Manasi Navare
  2019-10-15 23:20 ` [PATCH v9 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
                   ` (7 subsequent siblings)
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-15 23:05 UTC (permalink / raw)
  To: intel-gfx; +Cc: Jani Nikula

In the transcoder port sync mode, the slave transcoders mask their vblanks
until master transcoder's vblank so while disabling them, make
sure slaves are disabled first and then the masters.

v5:
* Dont pass dev priv to get_slave_crtc (Ville)
v4:
* Obtain slave state from master (Maarten)
v3:
* Rebase
v2:
* Use the intel_old_crtc_state_disables() helper

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c | 58 ++++++++++++++++++--
 1 file changed, 52 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index c7dbba237185..cb3903d41113 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -14077,6 +14077,37 @@ static void intel_old_crtc_state_disables(struct intel_atomic_state *state,
 						     new_crtc_state);
 }
 
+static void intel_trans_port_sync_modeset_disables(struct intel_atomic_state *state,
+						   struct intel_crtc *crtc,
+						   struct intel_crtc_state *old_crtc_state,
+						   struct intel_crtc_state *new_crtc_state)
+{
+	struct intel_crtc *slave_crtc = intel_get_slave_crtc(new_crtc_state);
+	struct intel_crtc_state *new_slave_crtc_state =
+		intel_atomic_get_new_crtc_state(state, slave_crtc);
+	struct intel_crtc_state *old_slave_crtc_state =
+		intel_atomic_get_old_crtc_state(state, slave_crtc);
+
+	WARN_ON(!slave_crtc || !new_slave_crtc_state ||
+		!old_slave_crtc_state);
+
+	/* Disable Slave first */
+	intel_pre_plane_update(old_slave_crtc_state, new_slave_crtc_state);
+	if (old_slave_crtc_state->base.active)
+		intel_old_crtc_state_disables(state,
+					      old_slave_crtc_state,
+					      new_slave_crtc_state,
+					      slave_crtc);
+
+	/* Disable Master */
+	intel_pre_plane_update(old_crtc_state, new_crtc_state);
+	if (old_crtc_state->base.active)
+		intel_old_crtc_state_disables(state,
+					      old_crtc_state,
+					      new_crtc_state,
+					      crtc);
+}
+
 static void intel_commit_modeset_disables(struct intel_atomic_state *state)
 {
 	struct intel_crtc_state *new_crtc_state, *old_crtc_state;
@@ -14095,13 +14126,28 @@ static void intel_commit_modeset_disables(struct intel_atomic_state *state)
 		if (!needs_modeset(new_crtc_state))
 			continue;
 
-		intel_pre_plane_update(old_crtc_state, new_crtc_state);
+		/* In case of Transcoder port Sync master slave CRTCs can be
+		 * assigned in any order and we need to make sure that
+		 * slave CRTCs are disabled first and then master CRTC since
+		 * Slave vblanks are masked till Master Vblanks.
+		 */
+		if (is_trans_port_sync_mode(new_crtc_state)) {
+			if (is_trans_port_sync_master(new_crtc_state))
+				intel_trans_port_sync_modeset_disables(state,
+								       crtc,
+								       old_crtc_state,
+								       new_crtc_state);
+			else
+				continue;
+		} else {
+			intel_pre_plane_update(old_crtc_state, new_crtc_state);
 
-		if (old_crtc_state->base.active)
-			intel_old_crtc_state_disables(state,
-						      old_crtc_state,
-						      new_crtc_state,
-						      crtc);
+			if (old_crtc_state->base.active)
+				intel_old_crtc_state_disables(state,
+							      old_crtc_state,
+							      new_crtc_state,
+							      crtc);
+		}
 	}
 }
 
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v9 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (5 preceding siblings ...)
  2019-10-15 23:05 ` [PATCH v8 6/6] drm/i915/display/icl: In port sync mode disable slaves first then master Manasi Navare
@ 2019-10-15 23:20 ` Manasi Navare
  2019-10-16  1:02 ` ✗ Fi.CI.BAT: failure for Enable Transcoder port sync for Tiled displays (rev2) Patchwork
                   ` (6 subsequent siblings)
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-15 23:20 UTC (permalink / raw)
  To: intel-gfx; +Cc: Daniel Vetter

In case of tiled displays when the two tiles are sent across two CRTCs
over two separate DP SST connectors, we need a mechanism to synchronize
the two CRTCs and their corresponding transcoders.
So use the master-slave mode where there is one master corresponding
to last horizontal and vertical tile that needs to be genlocked with
all other slave tiles.
This patch identifies saves the master transcoder in all the slave
CRTC states. This is needed to select the master CRTC/transcoder
while configuring transcoder port sync for the corresponding slaves.

v6:
Rebase (manasi)
v5:
* Address Ville's comments
* Just pass crtc_state, no need to check GEN (Ville)
v4:
* Rebase
v3:
* Use master_tramscoder instead of master_crtc for valid
HW state readouts (Ville)
v2:
* Move this to intel_mode_set_pipe_config(Jani N, Ville)
* Use slave_bitmask to save associated slaves in master crtc state (Ville)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c  | 118 ++++++++++++++++++
 drivers/gpu/drm/i915/display/intel_display.h  |   2 +
 .../drm/i915/display/intel_display_types.h    |   6 +
 3 files changed, 126 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index db9ff1bc1c64..0f4ab34d7281 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -519,6 +519,20 @@ needs_modeset(const struct intel_crtc_state *state)
 	return drm_atomic_crtc_needs_modeset(&state->base);
 }
 
+bool
+is_trans_port_sync_mode(const struct intel_crtc_state *crtc_state)
+{
+	return (crtc_state->master_transcoder != INVALID_TRANSCODER ||
+		crtc_state->sync_mode_slaves_mask);
+}
+
+static bool
+is_trans_port_sync_master(const struct intel_crtc_state *crtc_state)
+{
+	return (crtc_state->master_transcoder == INVALID_TRANSCODER &&
+		crtc_state->sync_mode_slaves_mask);
+}
+
 /*
  * Platform specific helpers to calculate the port PLL loopback- (clock.m),
  * and post-divider (clock.p) values, pre- (clock.vco) and post-divided fast
@@ -11775,6 +11789,91 @@ static bool c8_planes_changed(const struct intel_crtc_state *new_crtc_state)
 	return !old_crtc_state->c8_planes != !new_crtc_state->c8_planes;
 }
 
+static int icl_add_sync_mode_crtcs(struct intel_crtc_state *crtc_state)
+{
+	struct drm_crtc *crtc = crtc_state->base.crtc;
+	struct intel_atomic_state *state = to_intel_atomic_state(crtc_state->base.state);
+	struct drm_i915_private *dev_priv = to_i915(crtc_state->base.crtc->dev);
+	struct drm_connector *master_connector, *connector;
+	struct drm_connector_state *connector_state;
+	struct drm_connector_list_iter conn_iter;
+	struct drm_crtc *master_crtc = NULL;
+	struct drm_crtc_state *master_crtc_state;
+	struct intel_crtc_state *master_pipe_config;
+	int i, tile_group_id;
+
+	if (INTEL_GEN(dev_priv) < 11)
+		return 0;
+
+	/*
+	 * In case of tiled displays there could be one or more slaves but there is
+	 * only one master. Lets make the CRTC used by the connector corresponding
+	 * to the last horizonal and last vertical tile a master/genlock CRTC.
+	 * All the other CRTCs corresponding to other tiles of the same Tile group
+	 * are the slave CRTCs and hold a pointer to their genlock CRTC.
+	 */
+	for_each_new_connector_in_state(&state->base, connector, connector_state, i) {
+		if (connector_state->crtc != crtc)
+			continue;
+		if (!connector->has_tile)
+			continue;
+		if (crtc_state->base.mode.hdisplay != connector->tile_h_size ||
+		    crtc_state->base.mode.vdisplay != connector->tile_v_size)
+			return 0;
+		if (connector->tile_h_loc == connector->num_h_tile - 1 &&
+		    connector->tile_v_loc == connector->num_v_tile - 1)
+			continue;
+		crtc_state->sync_mode_slaves_mask = 0;
+		tile_group_id = connector->tile_group->id;
+		drm_connector_list_iter_begin(&dev_priv->drm, &conn_iter);
+		drm_for_each_connector_iter(master_connector, &conn_iter) {
+			struct drm_connector_state *master_conn_state = NULL;
+
+			if (!master_connector->has_tile)
+				continue;
+			if (master_connector->tile_h_loc != master_connector->num_h_tile - 1 ||
+			    master_connector->tile_v_loc != master_connector->num_v_tile - 1)
+				continue;
+			if (master_connector->tile_group->id != tile_group_id)
+				continue;
+
+			master_conn_state = drm_atomic_get_connector_state(&state->base,
+									   master_connector);
+			if (IS_ERR(master_conn_state)) {
+				drm_connector_list_iter_end(&conn_iter);
+				return PTR_ERR(master_conn_state);
+			}
+			if (master_conn_state->crtc) {
+				master_crtc = master_conn_state->crtc;
+				break;
+			}
+		}
+		drm_connector_list_iter_end(&conn_iter);
+
+		if (!master_crtc) {
+			DRM_DEBUG_KMS("Could not find Master CRTC for Slave CRTC %d\n",
+				      connector_state->crtc->base.id);
+			return -EINVAL;
+		}
+
+		master_crtc_state = drm_atomic_get_crtc_state(&state->base,
+							      master_crtc);
+		if (IS_ERR(master_crtc_state))
+			return PTR_ERR(master_crtc_state);
+
+		master_pipe_config = to_intel_crtc_state(master_crtc_state);
+		crtc_state->master_transcoder = master_pipe_config->cpu_transcoder;
+		master_pipe_config->sync_mode_slaves_mask |=
+			BIT(crtc_state->cpu_transcoder);
+		DRM_DEBUG_KMS("Master Transcoder = %s added for Slave CRTC = %d, slave transcoder bitmask = %d\n",
+			      transcoder_name(crtc_state->master_transcoder),
+			      crtc_state->base.crtc->base.id,
+			      master_pipe_config->sync_mode_slaves_mask);
+	}
+
+	return 0;
+}
+
 static int intel_crtc_atomic_check(struct intel_atomic_state *state,
 				   struct intel_crtc *crtc)
 {
@@ -12273,6 +12372,13 @@ clear_intel_crtc_state(struct intel_crtc_state *crtc_state)
 	if (IS_G4X(dev_priv) ||
 	    IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
 		saved_state->wm = crtc_state->wm;
+	/*
+	 * Save the slave bitmask which gets filled for master crtc state during
+	 * slave atomic check call.
+	 */
+	if (is_trans_port_sync_master(crtc_state))
+		saved_state->sync_mode_slaves_mask =
+			crtc_state->sync_mode_slaves_mask;
 
 	/* Keep base drm_crtc_state intact, only clear our extended struct */
 	BUILD_BUG_ON(offsetof(struct intel_crtc_state, base));
@@ -12366,6 +12472,15 @@ intel_modeset_pipe_config(struct intel_crtc_state *pipe_config)
 	drm_mode_set_crtcinfo(&pipe_config->base.adjusted_mode,
 			      CRTC_STEREO_DOUBLE);
 
+	/* Set the crtc_state defaults for trans_port_sync */
+	pipe_config->master_transcoder = INVALID_TRANSCODER;
+	ret = icl_add_sync_mode_crtcs(pipe_config);
+	if (ret) {
+		DRM_DEBUG_KMS("Cannot assign Sync Mode CRTCs: %d\n",
+			      ret);
+		return ret;
+	}
+
 	/* Pass our mode to the connectors and the CRTC to give them a chance to
 	 * adjust it according to limitations or connector properties, and also
 	 * a chance to reject the mode entirely.
@@ -12881,6 +12996,9 @@ intel_pipe_config_compare(const struct intel_crtc_state *current_config,
 	PIPE_CONF_CHECK_INFOFRAME(hdmi);
 	PIPE_CONF_CHECK_INFOFRAME(drm);
 
+	PIPE_CONF_CHECK_I(sync_mode_slaves_mask);
+	PIPE_CONF_CHECK_I(master_transcoder);
+
 #undef PIPE_CONF_CHECK_X
 #undef PIPE_CONF_CHECK_I
 #undef PIPE_CONF_CHECK_BOOL
diff --git a/drivers/gpu/drm/i915/display/intel_display.h b/drivers/gpu/drm/i915/display/intel_display.h
index bed203ec1df8..0cda275573e2 100644
--- a/drivers/gpu/drm/i915/display/intel_display.h
+++ b/drivers/gpu/drm/i915/display/intel_display.h
@@ -93,6 +93,7 @@ enum pipe {
 #define pipe_name(p) ((p) + 'A')
 
 enum transcoder {
+	INVALID_TRANSCODER = -1,
 	/*
 	 * The following transcoders have a 1:1 transcoder -> pipe mapping,
 	 * keep their values fixed: the code assumes that TRANSCODER_A=0, the
@@ -461,6 +462,7 @@ enum drm_mode_status
 intel_mode_valid_max_plane_size(struct drm_i915_private *dev_priv,
 				const struct drm_display_mode *mode);
 enum phy intel_port_to_phy(struct drm_i915_private *i915, enum port port);
+bool is_trans_port_sync_mode(const struct intel_crtc_state *state);
 
 void intel_plane_destroy(struct drm_plane *plane);
 void i830_enable_pipe(struct drm_i915_private *dev_priv, enum pipe pipe);
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index 40390d855815..8358152e403e 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -991,6 +991,12 @@ struct intel_crtc_state {
 
 	/* Forward Error correction State */
 	bool fec_enable;
+
+	/* Pointer to master transcoder in case of tiled displays */
+	enum transcoder master_transcoder;
+
+	/* Bitmask to indicate slaves attached */
+	u8 sync_mode_slaves_mask;
 };
 
 struct intel_crtc {
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v9 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync
  2019-10-15 23:05 ` [PATCH v8 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
@ 2019-10-15 23:24   ` Manasi Navare
  0 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-15 23:24 UTC (permalink / raw)
  To: intel-gfx; +Cc: Daniel Vetter

In case of tiled displays when the two tiles are sent across two CRTCs
over two separate DP SST connectors, we need a mechanism to synchronize
the two CRTCs and their corresponding transcoders.
So use the master-slave mode where there is one master corresponding
to last horizontal and vertical tile that needs to be genlocked with
all other slave tiles.
This patch identifies saves the master transcoder in all the slave
CRTC states. This is needed to select the master CRTC/transcoder
while configuring transcoder port sync for the corresponding slaves.

v6:
Rebase (manasi)
v5:
* Address Ville's comments
* Just pass crtc_state, no need to check GEN (Ville)
v4:
* Rebase
v3:
* Use master_tramscoder instead of master_crtc for valid
HW state readouts (Ville)
v2:
* Move this to intel_mode_set_pipe_config(Jani N, Ville)
* Use slave_bitmask to save associated slaves in master crtc state (Ville)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c  | 118 ++++++++++++++++++
 drivers/gpu/drm/i915/display/intel_display.h  |   2 +
 .../drm/i915/display/intel_display_types.h    |   6 +
 3 files changed, 126 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index db9ff1bc1c64..0f4ab34d7281 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -519,6 +519,20 @@ needs_modeset(const struct intel_crtc_state *state)
 	return drm_atomic_crtc_needs_modeset(&state->base);
 }
 
+bool
+is_trans_port_sync_mode(const struct intel_crtc_state *crtc_state)
+{
+	return (crtc_state->master_transcoder != INVALID_TRANSCODER ||
+		crtc_state->sync_mode_slaves_mask);
+}
+
+static bool
+is_trans_port_sync_master(const struct intel_crtc_state *crtc_state)
+{
+	return (crtc_state->master_transcoder == INVALID_TRANSCODER &&
+		crtc_state->sync_mode_slaves_mask);
+}
+
 /*
  * Platform specific helpers to calculate the port PLL loopback- (clock.m),
  * and post-divider (clock.p) values, pre- (clock.vco) and post-divided fast
@@ -11775,6 +11789,91 @@ static bool c8_planes_changed(const struct intel_crtc_state *new_crtc_state)
 	return !old_crtc_state->c8_planes != !new_crtc_state->c8_planes;
 }
 
+static int icl_add_sync_mode_crtcs(struct intel_crtc_state *crtc_state)
+{
+	struct drm_crtc *crtc = crtc_state->base.crtc;
+	struct intel_atomic_state *state = to_intel_atomic_state(crtc_state->base.state);
+	struct drm_i915_private *dev_priv = to_i915(crtc_state->base.crtc->dev);
+	struct drm_connector *master_connector, *connector;
+	struct drm_connector_state *connector_state;
+	struct drm_connector_list_iter conn_iter;
+	struct drm_crtc *master_crtc = NULL;
+	struct drm_crtc_state *master_crtc_state;
+	struct intel_crtc_state *master_pipe_config;
+	int i, tile_group_id;
+
+	if (INTEL_GEN(dev_priv) < 11)
+		return 0;
+
+	/*
+	 * In case of tiled displays there could be one or more slaves but there is
+	 * only one master. Lets make the CRTC used by the connector corresponding
+	 * to the last horizonal and last vertical tile a master/genlock CRTC.
+	 * All the other CRTCs corresponding to other tiles of the same Tile group
+	 * are the slave CRTCs and hold a pointer to their genlock CRTC.
+	 */
+	for_each_new_connector_in_state(&state->base, connector, connector_state, i) {
+		if (connector_state->crtc != crtc)
+			continue;
+		if (!connector->has_tile)
+			continue;
+		if (crtc_state->base.mode.hdisplay != connector->tile_h_size ||
+		    crtc_state->base.mode.vdisplay != connector->tile_v_size)
+			return 0;
+		if (connector->tile_h_loc == connector->num_h_tile - 1 &&
+		    connector->tile_v_loc == connector->num_v_tile - 1)
+			continue;
+		crtc_state->sync_mode_slaves_mask = 0;
+		tile_group_id = connector->tile_group->id;
+		drm_connector_list_iter_begin(&dev_priv->drm, &conn_iter);
+		drm_for_each_connector_iter(master_connector, &conn_iter) {
+			struct drm_connector_state *master_conn_state = NULL;
+
+			if (!master_connector->has_tile)
+				continue;
+			if (master_connector->tile_h_loc != master_connector->num_h_tile - 1 ||
+			    master_connector->tile_v_loc != master_connector->num_v_tile - 1)
+				continue;
+			if (master_connector->tile_group->id != tile_group_id)
+				continue;
+
+			master_conn_state = drm_atomic_get_connector_state(&state->base,
+									   master_connector);
+			if (IS_ERR(master_conn_state)) {
+				drm_connector_list_iter_end(&conn_iter);
+				return PTR_ERR(master_conn_state);
+			}
+			if (master_conn_state->crtc) {
+				master_crtc = master_conn_state->crtc;
+				break;
+			}
+		}
+		drm_connector_list_iter_end(&conn_iter);
+
+		if (!master_crtc) {
+			DRM_DEBUG_KMS("Could not find Master CRTC for Slave CRTC %d\n",
+				      connector_state->crtc->base.id);
+			return -EINVAL;
+		}
+
+		master_crtc_state = drm_atomic_get_crtc_state(&state->base,
+							      master_crtc);
+		if (IS_ERR(master_crtc_state))
+			return PTR_ERR(master_crtc_state);
+
+		master_pipe_config = to_intel_crtc_state(master_crtc_state);
+		crtc_state->master_transcoder = master_pipe_config->cpu_transcoder;
+		master_pipe_config->sync_mode_slaves_mask |=
+			BIT(crtc_state->cpu_transcoder);
+		DRM_DEBUG_KMS("Master Transcoder = %s added for Slave CRTC = %d, slave transcoder bitmask = %d\n",
+			      transcoder_name(crtc_state->master_transcoder),
+			      crtc_state->base.crtc->base.id,
+			      master_pipe_config->sync_mode_slaves_mask);
+	}
+
+	return 0;
+}
+
 static int intel_crtc_atomic_check(struct intel_atomic_state *state,
 				   struct intel_crtc *crtc)
 {
@@ -12273,6 +12372,13 @@ clear_intel_crtc_state(struct intel_crtc_state *crtc_state)
 	if (IS_G4X(dev_priv) ||
 	    IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
 		saved_state->wm = crtc_state->wm;
+	/*
+	 * Save the slave bitmask which gets filled for master crtc state during
+	 * slave atomic check call.
+	 */
+	if (is_trans_port_sync_master(crtc_state))
+		saved_state->sync_mode_slaves_mask =
+			crtc_state->sync_mode_slaves_mask;
 
 	/* Keep base drm_crtc_state intact, only clear our extended struct */
 	BUILD_BUG_ON(offsetof(struct intel_crtc_state, base));
@@ -12366,6 +12472,15 @@ intel_modeset_pipe_config(struct intel_crtc_state *pipe_config)
 	drm_mode_set_crtcinfo(&pipe_config->base.adjusted_mode,
 			      CRTC_STEREO_DOUBLE);
 
+	/* Set the crtc_state defaults for trans_port_sync */
+	pipe_config->master_transcoder = INVALID_TRANSCODER;
+	ret = icl_add_sync_mode_crtcs(pipe_config);
+	if (ret) {
+		DRM_DEBUG_KMS("Cannot assign Sync Mode CRTCs: %d\n",
+			      ret);
+		return ret;
+	}
+
 	/* Pass our mode to the connectors and the CRTC to give them a chance to
 	 * adjust it according to limitations or connector properties, and also
 	 * a chance to reject the mode entirely.
@@ -12881,6 +12996,9 @@ intel_pipe_config_compare(const struct intel_crtc_state *current_config,
 	PIPE_CONF_CHECK_INFOFRAME(hdmi);
 	PIPE_CONF_CHECK_INFOFRAME(drm);
 
+	PIPE_CONF_CHECK_I(sync_mode_slaves_mask);
+	PIPE_CONF_CHECK_I(master_transcoder);
+
 #undef PIPE_CONF_CHECK_X
 #undef PIPE_CONF_CHECK_I
 #undef PIPE_CONF_CHECK_BOOL
diff --git a/drivers/gpu/drm/i915/display/intel_display.h b/drivers/gpu/drm/i915/display/intel_display.h
index bed203ec1df8..0cda275573e2 100644
--- a/drivers/gpu/drm/i915/display/intel_display.h
+++ b/drivers/gpu/drm/i915/display/intel_display.h
@@ -93,6 +93,7 @@ enum pipe {
 #define pipe_name(p) ((p) + 'A')
 
 enum transcoder {
+	INVALID_TRANSCODER = -1,
 	/*
 	 * The following transcoders have a 1:1 transcoder -> pipe mapping,
 	 * keep their values fixed: the code assumes that TRANSCODER_A=0, the
@@ -461,6 +462,7 @@ enum drm_mode_status
 intel_mode_valid_max_plane_size(struct drm_i915_private *dev_priv,
 				const struct drm_display_mode *mode);
 enum phy intel_port_to_phy(struct drm_i915_private *i915, enum port port);
+bool is_trans_port_sync_mode(const struct intel_crtc_state *state);
 
 void intel_plane_destroy(struct drm_plane *plane);
 void i830_enable_pipe(struct drm_i915_private *dev_priv, enum pipe pipe);
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index 40390d855815..8358152e403e 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -991,6 +991,12 @@ struct intel_crtc_state {
 
 	/* Forward Error correction State */
 	bool fec_enable;
+
+	/* Pointer to master transcoder in case of tiled displays */
+	enum transcoder master_transcoder;
+
+	/* Bitmask to indicate slaves attached */
+	u8 sync_mode_slaves_mask;
 };
 
 struct intel_crtc {
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* ✗ Fi.CI.BAT: failure for Enable Transcoder port sync for Tiled displays (rev2)
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (6 preceding siblings ...)
  2019-10-15 23:20 ` [PATCH v9 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
@ 2019-10-16  1:02 ` Patchwork
  2019-10-16 14:20   ` Ville Syrjälä
  2019-10-16 18:47 ` [PATCH v10 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
                   ` (5 subsequent siblings)
  13 siblings, 1 reply; 18+ messages in thread
From: Patchwork @ 2019-10-16  1:02 UTC (permalink / raw)
  To: Manasi Navare; +Cc: intel-gfx

== Series Details ==

Series: Enable Transcoder port sync for Tiled displays (rev2)
URL   : https://patchwork.freedesktop.org/series/68062/
State : failure

== Summary ==

CI Bug Log - changes from CI_DRM_7100 -> Patchwork_14824
====================================================

Summary
-------

  **FAILURE**

  Serious unknown changes coming with Patchwork_14824 absolutely need to be
  verified manually.
  
  If you think the reported changes have nothing to do with the changes
  introduced in Patchwork_14824, please notify your bug team to allow them
  to document this new failure mode, which will reduce false positives in CI.

  External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/index.html

Possible new issues
-------------------

  Here are the unknown changes that may have been introduced in Patchwork_14824:

### IGT changes ###

#### Possible regressions ####

  * igt@runner@aborted:
    - fi-ilk-650:         NOTRUN -> [FAIL][1]
   [1]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-ilk-650/igt@runner@aborted.html
    - fi-gdg-551:         NOTRUN -> [FAIL][2]
   [2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-gdg-551/igt@runner@aborted.html
    - fi-snb-2520m:       NOTRUN -> [FAIL][3]
   [3]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-snb-2520m/igt@runner@aborted.html
    - fi-ivb-3770:        NOTRUN -> [FAIL][4]
   [4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-ivb-3770/igt@runner@aborted.html
    - fi-blb-e6850:       NOTRUN -> [FAIL][5]
   [5]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-blb-e6850/igt@runner@aborted.html
    - fi-bsw-kefka:       NOTRUN -> [FAIL][6]
   [6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-bsw-kefka/igt@runner@aborted.html
    - fi-elk-e7500:       NOTRUN -> [FAIL][7]
   [7]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-elk-e7500/igt@runner@aborted.html

  
Known issues
------------

  Here are the changes found in Patchwork_14824 that come from known issues:

### IGT changes ###

#### Issues hit ####

  * igt@gem_ctx_switch@legacy-render:
    - fi-bxt-dsi:         [PASS][8] -> [INCOMPLETE][9] ([fdo#103927] / [fdo#111381])
   [8]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_7100/fi-bxt-dsi/igt@gem_ctx_switch@legacy-render.html
   [9]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-bxt-dsi/igt@gem_ctx_switch@legacy-render.html

  * igt@gem_wait@basic-await-all:
    - fi-icl-u3:          [PASS][10] -> [DMESG-WARN][11] ([fdo#107724]) +1 similar issue
   [10]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_7100/fi-icl-u3/igt@gem_wait@basic-await-all.html
   [11]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-icl-u3/igt@gem_wait@basic-await-all.html

  
#### Possible fixes ####

  * igt@gem_exec_suspend@basic-s4-devices:
    - fi-kbl-x1275:       [INCOMPLETE][12] ([fdo#107139]) -> [PASS][13]
   [12]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_7100/fi-kbl-x1275/igt@gem_exec_suspend@basic-s4-devices.html
   [13]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-kbl-x1275/igt@gem_exec_suspend@basic-s4-devices.html

  * igt@gem_flink_basic@flink-lifetime:
    - fi-icl-u3:          [DMESG-WARN][14] ([fdo#107724]) -> [PASS][15] +1 similar issue
   [14]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_7100/fi-icl-u3/igt@gem_flink_basic@flink-lifetime.html
   [15]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-icl-u3/igt@gem_flink_basic@flink-lifetime.html

  * igt@i915_selftest@live_gem_contexts:
    - fi-cfl-8109u:       [DMESG-FAIL][16] -> [PASS][17]
   [16]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_7100/fi-cfl-8109u/igt@i915_selftest@live_gem_contexts.html
   [17]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-cfl-8109u/igt@i915_selftest@live_gem_contexts.html

  * igt@i915_selftest@live_hangcheck:
    - fi-icl-u3:          [INCOMPLETE][18] ([fdo#107713] / [fdo#108569]) -> [PASS][19]
   [18]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_7100/fi-icl-u3/igt@i915_selftest@live_hangcheck.html
   [19]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-icl-u3/igt@i915_selftest@live_hangcheck.html

  
  {name}: This element is suppressed. This means it is ignored when computing
          the status of the difference (SUCCESS, WARNING, or FAILURE).

  [fdo#103927]: https://bugs.freedesktop.org/show_bug.cgi?id=103927
  [fdo#107139]: https://bugs.freedesktop.org/show_bug.cgi?id=107139
  [fdo#107713]: https://bugs.freedesktop.org/show_bug.cgi?id=107713
  [fdo#107724]: https://bugs.freedesktop.org/show_bug.cgi?id=107724
  [fdo#108569]: https://bugs.freedesktop.org/show_bug.cgi?id=108569
  [fdo#111045]: https://bugs.freedesktop.org/show_bug.cgi?id=111045
  [fdo#111381]: https://bugs.freedesktop.org/show_bug.cgi?id=111381
  [fdo#111736]: https://bugs.freedesktop.org/show_bug.cgi?id=111736


Participating hosts (52 -> 45)
------------------------------

  Missing    (7): fi-ilk-m540 fi-hsw-4200u fi-byt-squawks fi-bsw-cyan fi-icl-y fi-byt-clapper fi-bdw-samus 


Build changes
-------------

  * CI: CI-20190529 -> None
  * Linux: CI_DRM_7100 -> Patchwork_14824

  CI-20190529: 20190529
  CI_DRM_7100: 38af7ec455b5b57fb24e4451a968bf4e92749035 @ git://anongit.freedesktop.org/gfx-ci/linux
  IGT_5231: e293051f8f99c72cb01d21e4b73a5928ea351eb3 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
  Patchwork_14824: 32277e878c3b2c3b31c160597c64c32ba73ddff8 @ git://anongit.freedesktop.org/gfx-ci/linux


== Linux commits ==

32277e878c3b drm/i915/display/icl: In port sync mode disable slaves first then master
aaa9fca3525c drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence
60f586d93f96 drm/i915/display/icl: Enable master-slaves in trans port sync
1f198809c232 drm/i915/display/icl: HW state readout for transcoder port sync config
db20e910ff44 drm/i915/display/icl: Enable TRANSCODER PORT SYNC for tiled displays across separate ports
129700759ed5 drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/index.html
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: ✗ Fi.CI.BAT: failure for Enable Transcoder port sync for Tiled displays (rev2)
  2019-10-16  1:02 ` ✗ Fi.CI.BAT: failure for Enable Transcoder port sync for Tiled displays (rev2) Patchwork
@ 2019-10-16 14:20   ` Ville Syrjälä
  2019-10-16 18:13     ` Manasi Navare
  0 siblings, 1 reply; 18+ messages in thread
From: Ville Syrjälä @ 2019-10-16 14:20 UTC (permalink / raw)
  To: intel-gfx

On Wed, Oct 16, 2019 at 01:02:08AM -0000, Patchwork wrote:
> == Series Details ==
> 
> Series: Enable Transcoder port sync for Tiled displays (rev2)
> URL   : https://patchwork.freedesktop.org/series/68062/
> State : failure
> 
> == Summary ==
> 
> CI Bug Log - changes from CI_DRM_7100 -> Patchwork_14824
> ====================================================
> 
> Summary
> -------
> 
>   **FAILURE**
> 
>   Serious unknown changes coming with Patchwork_14824 absolutely need to be
>   verified manually.
>   
>   If you think the reported changes have nothing to do with the changes
>   introduced in Patchwork_14824, please notify your bug team to allow them
>   to document this new failure mode, which will reduce false positives in CI.
> 
>   External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/index.html
> 
> Possible new issues
> -------------------
> 
>   Here are the unknown changes that may have been introduced in Patchwork_14824:
> 
> ### IGT changes ###
> 
> #### Possible regressions ####
> 
>   * igt@runner@aborted:
>     - fi-ilk-650:         NOTRUN -> [FAIL][1]
>    [1]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-ilk-650/igt@runner@aborted.html
>     - fi-gdg-551:         NOTRUN -> [FAIL][2]
>    [2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-gdg-551/igt@runner@aborted.html
>     - fi-snb-2520m:       NOTRUN -> [FAIL][3]
>    [3]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-snb-2520m/igt@runner@aborted.html
>     - fi-ivb-3770:        NOTRUN -> [FAIL][4]
>    [4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-ivb-3770/igt@runner@aborted.html
>     - fi-blb-e6850:       NOTRUN -> [FAIL][5]
>    [5]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-blb-e6850/igt@runner@aborted.html
>     - fi-bsw-kefka:       NOTRUN -> [FAIL][6]
>    [6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-bsw-kefka/igt@runner@aborted.html
>     - fi-elk-e7500:       NOTRUN -> [FAIL][7]
>    [7]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-elk-e7500/igt@runner@aborted.html

Still missing the master_transcoder "readout" for pre-hsw.

-- 
Ville Syrjälä
Intel
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: ✗ Fi.CI.BAT: failure for Enable Transcoder port sync for Tiled displays (rev2)
  2019-10-16 14:20   ` Ville Syrjälä
@ 2019-10-16 18:13     ` Manasi Navare
  0 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-16 18:13 UTC (permalink / raw)
  To: Ville Syrjälä; +Cc: intel-gfx

On Wed, Oct 16, 2019 at 05:20:10PM +0300, Ville Syrjälä wrote:
> On Wed, Oct 16, 2019 at 01:02:08AM -0000, Patchwork wrote:
> > == Series Details ==
> > 
> > Series: Enable Transcoder port sync for Tiled displays (rev2)
> > URL   : https://patchwork.freedesktop.org/series/68062/
> > State : failure
> > 
> > == Summary ==
> > 
> > CI Bug Log - changes from CI_DRM_7100 -> Patchwork_14824
> > ====================================================
> > 
> > Summary
> > -------
> > 
> >   **FAILURE**
> > 
> >   Serious unknown changes coming with Patchwork_14824 absolutely need to be
> >   verified manually.
> >   
> >   If you think the reported changes have nothing to do with the changes
> >   introduced in Patchwork_14824, please notify your bug team to allow them
> >   to document this new failure mode, which will reduce false positives in CI.
> > 
> >   External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/index.html
> > 
> > Possible new issues
> > -------------------
> > 
> >   Here are the unknown changes that may have been introduced in Patchwork_14824:
> > 
> > ### IGT changes ###
> > 
> > #### Possible regressions ####
> > 
> >   * igt@runner@aborted:
> >     - fi-ilk-650:         NOTRUN -> [FAIL][1]
> >    [1]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-ilk-650/igt@runner@aborted.html
> >     - fi-gdg-551:         NOTRUN -> [FAIL][2]
> >    [2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-gdg-551/igt@runner@aborted.html
> >     - fi-snb-2520m:       NOTRUN -> [FAIL][3]
> >    [3]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-snb-2520m/igt@runner@aborted.html
> >     - fi-ivb-3770:        NOTRUN -> [FAIL][4]
> >    [4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-ivb-3770/igt@runner@aborted.html
> >     - fi-blb-e6850:       NOTRUN -> [FAIL][5]
> >    [5]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-blb-e6850/igt@runner@aborted.html
> >     - fi-bsw-kefka:       NOTRUN -> [FAIL][6]
> >    [6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-bsw-kefka/igt@runner@aborted.html
> >     - fi-elk-e7500:       NOTRUN -> [FAIL][7]
> >    [7]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_14824/fi-elk-e7500/igt@runner@aborted.html
> 
> Still missing the master_transcoder "readout" for pre-hsw.
>

Yes I added the master_trans initialization to -1 to the haswell_get_config hook, but looks like
I need to just add it to verify_crtc_state() before calling the get_config() for any platform.
That should possibly fix it

manasi
 
> -- 
> Ville Syrjälä
> Intel
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH v10 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (7 preceding siblings ...)
  2019-10-16  1:02 ` ✗ Fi.CI.BAT: failure for Enable Transcoder port sync for Tiled displays (rev2) Patchwork
@ 2019-10-16 18:47 ` Manasi Navare
  2019-10-16 18:47 ` [PATCH v10 2/6] drm/i915/display/icl: Enable TRANSCODER PORT SYNC for tiled displays across separate ports Manasi Navare
                   ` (4 subsequent siblings)
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-16 18:47 UTC (permalink / raw)
  To: intel-gfx; +Cc: Daniel Vetter

In case of tiled displays when the two tiles are sent across two CRTCs
over two separate DP SST connectors, we need a mechanism to synchronize
the two CRTCs and their corresponding transcoders.
So use the master-slave mode where there is one master corresponding
to last horizontal and vertical tile that needs to be genlocked with
all other slave tiles.
This patch identifies saves the master transcoder in all the slave
CRTC states. This is needed to select the master CRTC/transcoder
while configuring transcoder port sync for the corresponding slaves.

v6:
Rebase (manasi)
v5:
* Address Ville's comments
* Just pass crtc_state, no need to check GEN (Ville)
v4:
* Rebase
v3:
* Use master_tramscoder instead of master_crtc for valid
HW state readouts (Ville)
v2:
* Move this to intel_mode_set_pipe_config(Jani N, Ville)
* Use slave_bitmask to save associated slaves in master crtc state (Ville)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c  | 118 ++++++++++++++++++
 drivers/gpu/drm/i915/display/intel_display.h  |   2 +
 .../drm/i915/display/intel_display_types.h    |   6 +
 3 files changed, 126 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index b42761c2ef63..a5fcc82656bf 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -519,6 +519,20 @@ needs_modeset(const struct intel_crtc_state *state)
 	return drm_atomic_crtc_needs_modeset(&state->base);
 }
 
+bool
+is_trans_port_sync_mode(const struct intel_crtc_state *crtc_state)
+{
+	return (crtc_state->master_transcoder != INVALID_TRANSCODER ||
+		crtc_state->sync_mode_slaves_mask);
+}
+
+static bool
+is_trans_port_sync_master(const struct intel_crtc_state *crtc_state)
+{
+	return (crtc_state->master_transcoder == INVALID_TRANSCODER &&
+		crtc_state->sync_mode_slaves_mask);
+}
+
 /*
  * Platform specific helpers to calculate the port PLL loopback- (clock.m),
  * and post-divider (clock.p) values, pre- (clock.vco) and post-divided fast
@@ -11775,6 +11789,91 @@ static bool c8_planes_changed(const struct intel_crtc_state *new_crtc_state)
 	return !old_crtc_state->c8_planes != !new_crtc_state->c8_planes;
 }
 
+static int icl_add_sync_mode_crtcs(struct intel_crtc_state *crtc_state)
+{
+	struct drm_crtc *crtc = crtc_state->base.crtc;
+	struct intel_atomic_state *state = to_intel_atomic_state(crtc_state->base.state);
+	struct drm_i915_private *dev_priv = to_i915(crtc_state->base.crtc->dev);
+	struct drm_connector *master_connector, *connector;
+	struct drm_connector_state *connector_state;
+	struct drm_connector_list_iter conn_iter;
+	struct drm_crtc *master_crtc = NULL;
+	struct drm_crtc_state *master_crtc_state;
+	struct intel_crtc_state *master_pipe_config;
+	int i, tile_group_id;
+
+	if (INTEL_GEN(dev_priv) < 11)
+		return 0;
+
+	/*
+	 * In case of tiled displays there could be one or more slaves but there is
+	 * only one master. Lets make the CRTC used by the connector corresponding
+	 * to the last horizonal and last vertical tile a master/genlock CRTC.
+	 * All the other CRTCs corresponding to other tiles of the same Tile group
+	 * are the slave CRTCs and hold a pointer to their genlock CRTC.
+	 */
+	for_each_new_connector_in_state(&state->base, connector, connector_state, i) {
+		if (connector_state->crtc != crtc)
+			continue;
+		if (!connector->has_tile)
+			continue;
+		if (crtc_state->base.mode.hdisplay != connector->tile_h_size ||
+		    crtc_state->base.mode.vdisplay != connector->tile_v_size)
+			return 0;
+		if (connector->tile_h_loc == connector->num_h_tile - 1 &&
+		    connector->tile_v_loc == connector->num_v_tile - 1)
+			continue;
+		crtc_state->sync_mode_slaves_mask = 0;
+		tile_group_id = connector->tile_group->id;
+		drm_connector_list_iter_begin(&dev_priv->drm, &conn_iter);
+		drm_for_each_connector_iter(master_connector, &conn_iter) {
+			struct drm_connector_state *master_conn_state = NULL;
+
+			if (!master_connector->has_tile)
+				continue;
+			if (master_connector->tile_h_loc != master_connector->num_h_tile - 1 ||
+			    master_connector->tile_v_loc != master_connector->num_v_tile - 1)
+				continue;
+			if (master_connector->tile_group->id != tile_group_id)
+				continue;
+
+			master_conn_state = drm_atomic_get_connector_state(&state->base,
+									   master_connector);
+			if (IS_ERR(master_conn_state)) {
+				drm_connector_list_iter_end(&conn_iter);
+				return PTR_ERR(master_conn_state);
+			}
+			if (master_conn_state->crtc) {
+				master_crtc = master_conn_state->crtc;
+				break;
+			}
+		}
+		drm_connector_list_iter_end(&conn_iter);
+
+		if (!master_crtc) {
+			DRM_DEBUG_KMS("Could not find Master CRTC for Slave CRTC %d\n",
+				      connector_state->crtc->base.id);
+			return -EINVAL;
+		}
+
+		master_crtc_state = drm_atomic_get_crtc_state(&state->base,
+							      master_crtc);
+		if (IS_ERR(master_crtc_state))
+			return PTR_ERR(master_crtc_state);
+
+		master_pipe_config = to_intel_crtc_state(master_crtc_state);
+		crtc_state->master_transcoder = master_pipe_config->cpu_transcoder;
+		master_pipe_config->sync_mode_slaves_mask |=
+			BIT(crtc_state->cpu_transcoder);
+		DRM_DEBUG_KMS("Master Transcoder = %s added for Slave CRTC = %d, slave transcoder bitmask = %d\n",
+			      transcoder_name(crtc_state->master_transcoder),
+			      crtc_state->base.crtc->base.id,
+			      master_pipe_config->sync_mode_slaves_mask);
+	}
+
+	return 0;
+}
+
 static int intel_crtc_atomic_check(struct intel_atomic_state *state,
 				   struct intel_crtc *crtc)
 {
@@ -12273,6 +12372,13 @@ clear_intel_crtc_state(struct intel_crtc_state *crtc_state)
 	if (IS_G4X(dev_priv) ||
 	    IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
 		saved_state->wm = crtc_state->wm;
+	/*
+	 * Save the slave bitmask which gets filled for master crtc state during
+	 * slave atomic check call.
+	 */
+	if (is_trans_port_sync_master(crtc_state))
+		saved_state->sync_mode_slaves_mask =
+			crtc_state->sync_mode_slaves_mask;
 
 	/* Keep base drm_crtc_state intact, only clear our extended struct */
 	BUILD_BUG_ON(offsetof(struct intel_crtc_state, base));
@@ -12366,6 +12472,15 @@ intel_modeset_pipe_config(struct intel_crtc_state *pipe_config)
 	drm_mode_set_crtcinfo(&pipe_config->base.adjusted_mode,
 			      CRTC_STEREO_DOUBLE);
 
+	/* Set the crtc_state defaults for trans_port_sync */
+	pipe_config->master_transcoder = INVALID_TRANSCODER;
+	ret = icl_add_sync_mode_crtcs(pipe_config);
+	if (ret) {
+		DRM_DEBUG_KMS("Cannot assign Sync Mode CRTCs: %d\n",
+			      ret);
+		return ret;
+	}
+
 	/* Pass our mode to the connectors and the CRTC to give them a chance to
 	 * adjust it according to limitations or connector properties, and also
 	 * a chance to reject the mode entirely.
@@ -12881,6 +12996,9 @@ intel_pipe_config_compare(const struct intel_crtc_state *current_config,
 	PIPE_CONF_CHECK_INFOFRAME(hdmi);
 	PIPE_CONF_CHECK_INFOFRAME(drm);
 
+	PIPE_CONF_CHECK_I(sync_mode_slaves_mask);
+	PIPE_CONF_CHECK_I(master_transcoder);
+
 #undef PIPE_CONF_CHECK_X
 #undef PIPE_CONF_CHECK_I
 #undef PIPE_CONF_CHECK_BOOL
diff --git a/drivers/gpu/drm/i915/display/intel_display.h b/drivers/gpu/drm/i915/display/intel_display.h
index bed203ec1df8..0cda275573e2 100644
--- a/drivers/gpu/drm/i915/display/intel_display.h
+++ b/drivers/gpu/drm/i915/display/intel_display.h
@@ -93,6 +93,7 @@ enum pipe {
 #define pipe_name(p) ((p) + 'A')
 
 enum transcoder {
+	INVALID_TRANSCODER = -1,
 	/*
 	 * The following transcoders have a 1:1 transcoder -> pipe mapping,
 	 * keep their values fixed: the code assumes that TRANSCODER_A=0, the
@@ -461,6 +462,7 @@ enum drm_mode_status
 intel_mode_valid_max_plane_size(struct drm_i915_private *dev_priv,
 				const struct drm_display_mode *mode);
 enum phy intel_port_to_phy(struct drm_i915_private *i915, enum port port);
+bool is_trans_port_sync_mode(const struct intel_crtc_state *state);
 
 void intel_plane_destroy(struct drm_plane *plane);
 void i830_enable_pipe(struct drm_i915_private *dev_priv, enum pipe pipe);
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index 40390d855815..8358152e403e 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -991,6 +991,12 @@ struct intel_crtc_state {
 
 	/* Forward Error correction State */
 	bool fec_enable;
+
+	/* Pointer to master transcoder in case of tiled displays */
+	enum transcoder master_transcoder;
+
+	/* Bitmask to indicate slaves attached */
+	u8 sync_mode_slaves_mask;
 };
 
 struct intel_crtc {
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v10 2/6] drm/i915/display/icl: Enable TRANSCODER PORT SYNC for tiled displays across separate ports
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (8 preceding siblings ...)
  2019-10-16 18:47 ` [PATCH v10 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
@ 2019-10-16 18:47 ` Manasi Navare
  2019-10-16 18:47 ` [PATCH v10 3/6] drm/i915/display/icl: HW state readout for transcoder port sync config Manasi Navare
                   ` (3 subsequent siblings)
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-16 18:47 UTC (permalink / raw)
  To: intel-gfx; +Cc: Jani Nikula, Daniel Vetter

In case of tiled displays where different tiles are displayed across
different ports, we need to synchronize the transcoders involved.
This patch implements the transcoder port sync feature for
synchronizing one master transcoder with one or more slave
transcoders. This is only enbaled in slave transcoder
and the master transcoder is unaware that it is operating
in this mode.
This has been tested with tiled display connected to ICL.

v7:
* Rebase on Maarten's patches
v6:
* Use master_trans +1 and address missing trans_edp case (Ville)
v5:
* Add TRANSCODER_D case and MISSING_CASE (Maarten)
v4:
Rebase
v3:
* Check of DP_MST moved to atomic_check (Maarten)
v2:
* Do not use RMW, just write to the register in commit (Jani N)

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c | 33 ++++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index a5fcc82656bf..64c6fca014fc 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -4405,6 +4405,36 @@ static void icl_set_pipe_chicken(struct intel_crtc *crtc)
 	I915_WRITE(PIPE_CHICKEN(pipe), tmp);
 }
 
+static void icl_enable_trans_port_sync(const struct intel_crtc_state *crtc_state)
+{
+	struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
+	struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
+	u32 trans_ddi_func_ctl2_val;
+	u8 master_select;
+
+	/*
+	 * Configure the master select and enable Transcoder Port Sync for
+	 * Slave CRTCs transcoder.
+	 */
+	if (crtc_state->master_transcoder == INVALID_TRANSCODER)
+		return;
+
+	if (crtc_state->master_transcoder == TRANSCODER_EDP)
+		master_select = 0;
+	else
+		master_select = crtc_state->master_transcoder + 1;
+
+	/* Set the master select bits for Tranascoder Port Sync */
+	trans_ddi_func_ctl2_val = (PORT_SYNC_MODE_MASTER_SELECT(master_select) &
+				   PORT_SYNC_MODE_MASTER_SELECT_MASK) <<
+		PORT_SYNC_MODE_MASTER_SELECT_SHIFT;
+	/* Enable Transcoder Port Sync */
+	trans_ddi_func_ctl2_val |= PORT_SYNC_MODE_ENABLE;
+
+	I915_WRITE(TRANS_DDI_FUNC_CTL2(crtc_state->cpu_transcoder),
+		   trans_ddi_func_ctl2_val);
+}
+
 static void intel_fdi_normal_train(struct intel_crtc *crtc)
 {
 	struct drm_device *dev = crtc->base.dev;
@@ -6429,6 +6459,9 @@ static void haswell_crtc_enable(struct intel_crtc_state *pipe_config,
 	if (!transcoder_is_dsi(cpu_transcoder))
 		intel_set_pipe_timings(pipe_config);
 
+	if (INTEL_GEN(dev_priv) >= 11)
+		icl_enable_trans_port_sync(pipe_config);
+
 	intel_set_pipe_src_size(pipe_config);
 
 	if (cpu_transcoder != TRANSCODER_EDP &&
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v10 3/6] drm/i915/display/icl: HW state readout for transcoder port sync config
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (9 preceding siblings ...)
  2019-10-16 18:47 ` [PATCH v10 2/6] drm/i915/display/icl: Enable TRANSCODER PORT SYNC for tiled displays across separate ports Manasi Navare
@ 2019-10-16 18:47 ` Manasi Navare
  2019-10-16 18:47 ` [PATCH v10 4/6] drm/i915/display/icl: Enable master-slaves in trans port sync Manasi Navare
                   ` (2 subsequent siblings)
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-16 18:47 UTC (permalink / raw)
  To: intel-gfx; +Cc: Jani Nikula

After the state is committed, we readout the HW registers and compare
the HW state with the SW state that we just committed.
For Transcdoer port sync, we add master_transcoder and the
salves bitmask to the crtc_state, hence we need to read those during
the HW state readout to avoid pipe state mismatch.

v10:
* Initialize master_tarnscoder readout for all platforms (Ville)
v9:
* Initialize master_transcoder = INVALID at get config (Ville)
v8:
* Use master_select -1, address TRANS_EDP case (Ville)
* Rename master_transcoder to _readout (Lucas)
v7:
* NDont read HW state for DSI
v6:
* Go through both parts of HW readout (Maarten)
* Add a WARN if the same trans configured as
master and slave (Ville, Maarten)
v5:
* Add return INVALID in defaut case (Maarten)
v4:
* Get power domains in master loop for get_config (Ville)
v3:
* Add TRANSCODER_D (Maarten)
* v3 Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
v2:
* Add Transcoder_D and MISSING_CASE (Maarten)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c | 60 ++++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index 64c6fca014fc..e33edd2844ad 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -10431,6 +10431,59 @@ static void haswell_get_ddi_port_state(struct intel_crtc *crtc,
 	}
 }
 
+static enum transcoder transcoder_master_readout(struct drm_i915_private *dev_priv,
+						 enum transcoder cpu_transcoder)
+{
+	u32 trans_port_sync, master_select;
+
+	trans_port_sync = I915_READ(TRANS_DDI_FUNC_CTL2(cpu_transcoder));
+
+	if ((trans_port_sync & PORT_SYNC_MODE_ENABLE) == 0)
+		return INVALID_TRANSCODER;
+
+	master_select = trans_port_sync &
+			PORT_SYNC_MODE_MASTER_SELECT_MASK;
+	if (master_select == 0)
+		return TRANSCODER_EDP;
+	else
+		return master_select - 1;
+}
+
+static void icelake_get_trans_port_sync_config(struct intel_crtc_state *crtc_state)
+{
+	struct drm_i915_private *dev_priv = to_i915(crtc_state->base.crtc->dev);
+	u32 transcoders;
+	enum transcoder cpu_transcoder;
+
+	crtc_state->master_transcoder = transcoder_master_readout(dev_priv,
+								  crtc_state->cpu_transcoder);
+
+	transcoders = BIT(TRANSCODER_A) |
+		BIT(TRANSCODER_B) |
+		BIT(TRANSCODER_C) |
+		BIT(TRANSCODER_D);
+	for_each_cpu_transcoder_masked(dev_priv, cpu_transcoder, transcoders) {
+		enum intel_display_power_domain power_domain;
+		intel_wakeref_t trans_wakeref;
+
+		power_domain = POWER_DOMAIN_TRANSCODER(cpu_transcoder);
+		trans_wakeref = intel_display_power_get_if_enabled(dev_priv,
+								   power_domain);
+
+		if (!trans_wakeref)
+			continue;
+
+		if (transcoder_master_readout(dev_priv, cpu_transcoder) ==
+		    crtc_state->cpu_transcoder)
+			crtc_state->sync_mode_slaves_mask |= BIT(cpu_transcoder);
+
+		intel_display_power_put(dev_priv, power_domain, trans_wakeref);
+	}
+
+	WARN_ON(crtc_state->master_transcoder != INVALID_TRANSCODER &&
+		crtc_state->sync_mode_slaves_mask);
+}
+
 static bool haswell_get_pipe_config(struct intel_crtc *crtc,
 				    struct intel_crtc_state *pipe_config)
 {
@@ -10550,6 +10603,10 @@ static bool haswell_get_pipe_config(struct intel_crtc *crtc,
 		pipe_config->pixel_multiplier = 1;
 	}
 
+	if (INTEL_GEN(dev_priv) >= 11 &&
+	    !transcoder_is_dsi(pipe_config->cpu_transcoder))
+		icelake_get_trans_port_sync_config(pipe_config);
+
 out:
 	for_each_power_domain(power_domain, power_domain_mask)
 		intel_display_power_put(dev_priv,
@@ -13297,6 +13354,9 @@ verify_crtc_state(struct intel_crtc *crtc,
 
 	DRM_DEBUG_KMS("[CRTC:%d:%s]\n", crtc->base.base.id, crtc->base.name);
 
+	/* Initialize the master_transcoder before readout */
+	pipe_config->master_transcoder = INVALID_TRANSCODER;
+
 	active = dev_priv->display.get_pipe_config(crtc, pipe_config);
 
 	/* we keep both pipes enabled on 830 */
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v10 4/6] drm/i915/display/icl: Enable master-slaves in trans port sync
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (10 preceding siblings ...)
  2019-10-16 18:47 ` [PATCH v10 3/6] drm/i915/display/icl: HW state readout for transcoder port sync config Manasi Navare
@ 2019-10-16 18:47 ` Manasi Navare
  2019-10-16 18:47 ` [PATCH v10 5/6] drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence Manasi Navare
  2019-10-16 18:47 ` [PATCH v10 6/6] drm/i915/display/icl: In port sync mode disable slaves first then master Manasi Navare
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-16 18:47 UTC (permalink / raw)
  To: intel-gfx; +Cc: Daniel Vetter

As per the display enable sequence, we need to follow the enable sequence
for slaves first with DP_TP_CTL set to Idle and configure the transcoder
port sync register to select the corersponding master, then follow the
enable sequence for master leaving DP_TP_CTL to idle.
At this point the transcoder port sync mode is configured and enabled
and the Vblanks of both ports are synchronized so then set DP_TP_CTL
for the slave and master to Normal and do post crtc enable updates.

v9:
Remove update_scanline_offset to rebase on Maarten's patch (Manasi)
v8:
* Rebase on Maarten's patches (Manasi)
v7:
* Use ffs(slaves) to get slave crtc (Ville)
v6:
* Modeset implies active_changed, remove one condition (Maarten)
v5:
* Fix checkpatch warning (Manasi)
v4:
* Reuse skl_commit_modeset_enables() hook (Maarten)
* Obtain slave crtc and states from master (Maarten)
v3:
* Rebase on drm-tip (Manasi)
v2:
* Create a icl_update_crtcs hook (Maarten, Danvet)
* This sequence only for CRTCs in trans port sync mode (Maarten)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_ddi.c     |   3 +-
 drivers/gpu/drm/i915/display/intel_display.c | 136 ++++++++++++++++++-
 drivers/gpu/drm/i915/display/intel_display.h |   2 +
 3 files changed, 137 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index 80f8e2698be0..23a7348c2fd5 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -3572,7 +3572,8 @@ static void hsw_ddi_pre_enable_dp(struct intel_encoder *encoder,
 					      true);
 	intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
 	intel_dp_start_link_train(intel_dp);
-	if (port != PORT_A || INTEL_GEN(dev_priv) >= 9)
+	if ((port != PORT_A || INTEL_GEN(dev_priv) >= 9) &&
+	    !is_trans_port_sync_mode(crtc_state))
 		intel_dp_stop_link_train(intel_dp);
 
 	intel_ddi_enable_fec(encoder, crtc_state);
diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index e33edd2844ad..d86e0bf02a98 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -14041,6 +14041,18 @@ static void intel_update_crtc(struct intel_crtc *crtc,
 		intel_crtc_arm_fifo_underrun(crtc, new_crtc_state);
 }
 
+static struct intel_crtc *intel_get_slave_crtc(const struct intel_crtc_state *new_crtc_state)
+{
+	struct drm_i915_private *dev_priv = to_i915(new_crtc_state->base.crtc->dev);
+	enum transcoder slave_transcoder;
+
+	WARN_ON(!is_power_of_2(new_crtc_state->sync_mode_slaves_mask));
+
+	slave_transcoder = ffs(new_crtc_state->sync_mode_slaves_mask) - 1;
+	return intel_get_crtc_for_pipe(dev_priv,
+				       (enum pipe)slave_transcoder);
+}
+
 static void intel_old_crtc_state_disables(struct intel_atomic_state *state,
 					  struct intel_crtc_state *old_crtc_state,
 					  struct intel_crtc_state *new_crtc_state,
@@ -14119,6 +14131,113 @@ static void intel_commit_modeset_enables(struct intel_atomic_state *state)
 	}
 }
 
+static void intel_crtc_enable_trans_port_sync(struct intel_crtc *crtc,
+					      struct intel_atomic_state *state,
+					      struct intel_crtc_state *new_crtc_state)
+{
+	struct drm_i915_private *dev_priv = to_i915(state->base.dev);
+
+	intel_crtc_update_active_timings(new_crtc_state);
+	dev_priv->display.crtc_enable(new_crtc_state, state);
+	intel_crtc_enable_pipe_crc(crtc);
+}
+
+static void intel_set_dp_tp_ctl_normal(struct intel_crtc *crtc,
+				       struct intel_atomic_state *state)
+{
+	struct drm_connector_state *conn_state;
+	struct drm_connector *conn;
+	struct intel_dp *intel_dp;
+	int i;
+
+	for_each_new_connector_in_state(&state->base, conn, conn_state, i) {
+		if (conn_state->crtc == &crtc->base)
+			break;
+	}
+	intel_dp = enc_to_intel_dp(&intel_attached_encoder(conn)->base);
+	intel_dp_stop_link_train(intel_dp);
+}
+
+static void intel_post_crtc_enable_updates(struct intel_crtc *crtc,
+					   struct intel_atomic_state *state)
+{
+	struct intel_crtc_state *new_crtc_state =
+		intel_atomic_get_new_crtc_state(state, crtc);
+	struct intel_crtc_state *old_crtc_state =
+		intel_atomic_get_old_crtc_state(state, crtc);
+	struct intel_plane_state *new_plane_state =
+		intel_atomic_get_new_plane_state(state,
+						 to_intel_plane(crtc->base.primary));
+	bool modeset = needs_modeset(new_crtc_state);
+
+	if (new_crtc_state->update_pipe && !new_crtc_state->enable_fbc)
+		intel_fbc_disable(crtc);
+	else if (new_plane_state)
+		intel_fbc_enable(crtc, new_crtc_state, new_plane_state);
+
+	/* Perform vblank evasion around commit operation */
+	intel_pipe_update_start(new_crtc_state);
+	commit_pipe_config(state, old_crtc_state, new_crtc_state);
+	skl_update_planes_on_crtc(state, crtc);
+	intel_pipe_update_end(new_crtc_state);
+
+	/*
+	 * We usually enable FIFO underrun interrupts as part of the
+	 * CRTC enable sequence during modesets.  But when we inherit a
+	 * valid pipe configuration from the BIOS we need to take care
+	 * of enabling them on the CRTC's first fastset.
+	 */
+	if (new_crtc_state->update_pipe && !modeset &&
+	    old_crtc_state->base.mode.private_flags & I915_MODE_FLAG_INHERITED)
+		intel_crtc_arm_fifo_underrun(crtc, new_crtc_state);
+}
+
+static void intel_update_trans_port_sync_crtcs(struct intel_crtc *crtc,
+					       struct intel_atomic_state *state,
+					       struct intel_crtc_state *old_crtc_state,
+					       struct intel_crtc_state *new_crtc_state)
+{
+	struct intel_crtc *slave_crtc = intel_get_slave_crtc(new_crtc_state);
+	struct intel_crtc_state *new_slave_crtc_state =
+		intel_atomic_get_new_crtc_state(state, slave_crtc);
+	struct intel_crtc_state *old_slave_crtc_state =
+		intel_atomic_get_old_crtc_state(state, slave_crtc);
+
+	WARN_ON(!slave_crtc || !new_slave_crtc_state ||
+		!old_slave_crtc_state);
+
+	DRM_DEBUG_KMS("Updating Transcoder Port Sync Master CRTC = %d %s and Slave CRTC %d %s\n",
+		      crtc->base.base.id, crtc->base.name, slave_crtc->base.base.id,
+		      slave_crtc->base.name);
+
+	/* Enable seq for slave with with DP_TP_CTL left Idle until the
+	 * master is ready
+	 */
+	intel_crtc_enable_trans_port_sync(slave_crtc,
+					  state,
+					  new_slave_crtc_state);
+
+	/* Enable seq for master with with DP_TP_CTL left Idle */
+	intel_crtc_enable_trans_port_sync(crtc,
+					  state,
+					  new_crtc_state);
+
+	/* Set Slave's DP_TP_CTL to Normal */
+	intel_set_dp_tp_ctl_normal(slave_crtc,
+				   state);
+
+	/* Set Master's DP_TP_CTL To Normal */
+	usleep_range(200, 400);
+	intel_set_dp_tp_ctl_normal(crtc,
+				   state);
+
+	/* Now do the post crtc enable for all master and slaves */
+	intel_post_crtc_enable_updates(slave_crtc,
+				       state);
+	intel_post_crtc_enable_updates(crtc,
+				       state);
+}
+
 static void skl_commit_modeset_enables(struct intel_atomic_state *state)
 {
 	struct drm_i915_private *dev_priv = to_i915(state->base.dev);
@@ -14153,6 +14272,7 @@ static void skl_commit_modeset_enables(struct intel_atomic_state *state)
 		for_each_oldnew_intel_crtc_in_state(state, crtc, old_crtc_state, new_crtc_state, i) {
 			bool vbl_wait = false;
 			unsigned int cmask = drm_crtc_mask(&crtc->base);
+			bool modeset = needs_modeset(new_crtc_state);
 
 			pipe = crtc->pipe;
 
@@ -14175,12 +14295,22 @@ static void skl_commit_modeset_enables(struct intel_atomic_state *state)
 			 */
 			if (!skl_ddb_entry_equal(&new_crtc_state->wm.skl.ddb,
 						 &old_crtc_state->wm.skl.ddb) &&
-			    !new_crtc_state->base.active_changed &&
+			    !modeset &&
 			    state->wm_results.dirty_pipes != updated)
 				vbl_wait = true;
 
-			intel_update_crtc(crtc, state, old_crtc_state,
-					  new_crtc_state);
+			if (modeset && is_trans_port_sync_mode(new_crtc_state)) {
+				if (is_trans_port_sync_master(new_crtc_state))
+					intel_update_trans_port_sync_crtcs(crtc,
+									   state,
+									   old_crtc_state,
+									   new_crtc_state);
+				else
+					continue;
+			} else {
+				intel_update_crtc(crtc, state, old_crtc_state,
+						  new_crtc_state);
+			}
 
 			if (vbl_wait)
 				intel_wait_for_vblank(dev_priv, pipe);
diff --git a/drivers/gpu/drm/i915/display/intel_display.h b/drivers/gpu/drm/i915/display/intel_display.h
index 0cda275573e2..a49580632a8d 100644
--- a/drivers/gpu/drm/i915/display/intel_display.h
+++ b/drivers/gpu/drm/i915/display/intel_display.h
@@ -27,6 +27,7 @@
 
 #include <drm/drm_util.h>
 #include <drm/i915_drm.h>
+#include "intel_dp_link_training.h"
 
 enum link_m_n_set;
 struct dpll;
@@ -54,6 +55,7 @@ struct intel_plane;
 struct intel_plane_state;
 struct intel_remapped_info;
 struct intel_rotation_info;
+struct intel_crtc_state;
 
 enum i915_gpio {
 	GPIOA,
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v10 5/6] drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (11 preceding siblings ...)
  2019-10-16 18:47 ` [PATCH v10 4/6] drm/i915/display/icl: Enable master-slaves in trans port sync Manasi Navare
@ 2019-10-16 18:47 ` Manasi Navare
  2019-10-16 18:47 ` [PATCH v10 6/6] drm/i915/display/icl: In port sync mode disable slaves first then master Manasi Navare
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-16 18:47 UTC (permalink / raw)
  To: intel-gfx; +Cc: Jani Nikula

This clears the transcoder port sync bits of the TRANS_DDI_FUNC_CTL2
register during crtc_disable().

v3:
* Rebase on maarten's patches
v2:
* Directly write the trans_port_sync reg value (Maarten)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c | 22 ++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index d86e0bf02a98..15491e2ccf1e 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -4435,6 +4435,25 @@ static void icl_enable_trans_port_sync(const struct intel_crtc_state *crtc_state
 		   trans_ddi_func_ctl2_val);
 }
 
+static void icl_disable_transcoder_port_sync(const struct intel_crtc_state *old_crtc_state)
+{
+	struct intel_crtc *crtc = to_intel_crtc(old_crtc_state->base.crtc);
+	struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
+	i915_reg_t reg;
+	u32 trans_ddi_func_ctl2_val;
+
+	if (old_crtc_state->master_transcoder == INVALID_TRANSCODER)
+		return;
+
+	DRM_DEBUG_KMS("Disabling Transcoder Port Sync on Slave Transcoder %s\n",
+		      transcoder_name(old_crtc_state->cpu_transcoder));
+
+	reg = TRANS_DDI_FUNC_CTL2(old_crtc_state->cpu_transcoder);
+	trans_ddi_func_ctl2_val = ~(PORT_SYNC_MODE_ENABLE |
+				    PORT_SYNC_MODE_MASTER_SELECT_MASK);
+	I915_WRITE(reg, trans_ddi_func_ctl2_val);
+}
+
 static void intel_fdi_normal_train(struct intel_crtc *crtc)
 {
 	struct drm_device *dev = crtc->base.dev;
@@ -6639,6 +6658,9 @@ static void haswell_crtc_disable(struct intel_crtc_state *old_crtc_state,
 	if (intel_crtc_has_type(old_crtc_state, INTEL_OUTPUT_DP_MST))
 		intel_ddi_set_vc_payload_alloc(old_crtc_state, false);
 
+	if (INTEL_GEN(dev_priv) >= 11)
+		icl_disable_transcoder_port_sync(old_crtc_state);
+
 	if (!transcoder_is_dsi(cpu_transcoder))
 		intel_ddi_disable_transcoder_func(old_crtc_state);
 
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

* [PATCH v10 6/6] drm/i915/display/icl: In port sync mode disable slaves first then master
  2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
                   ` (12 preceding siblings ...)
  2019-10-16 18:47 ` [PATCH v10 5/6] drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence Manasi Navare
@ 2019-10-16 18:47 ` Manasi Navare
  13 siblings, 0 replies; 18+ messages in thread
From: Manasi Navare @ 2019-10-16 18:47 UTC (permalink / raw)
  To: intel-gfx; +Cc: Jani Nikula

In the transcoder port sync mode, the slave transcoders mask their vblanks
until master transcoder's vblank so while disabling them, make
sure slaves are disabled first and then the masters.

v5:
* Dont pass dev priv to get_slave_crtc (Ville)
v4:
* Obtain slave state from master (Maarten)
v3:
* Rebase
v2:
* Use the intel_old_crtc_state_disables() helper

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
 drivers/gpu/drm/i915/display/intel_display.c | 58 ++++++++++++++++++--
 1 file changed, 52 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index 15491e2ccf1e..b608ece63397 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -14110,6 +14110,37 @@ static void intel_old_crtc_state_disables(struct intel_atomic_state *state,
 						     new_crtc_state);
 }
 
+static void intel_trans_port_sync_modeset_disables(struct intel_atomic_state *state,
+						   struct intel_crtc *crtc,
+						   struct intel_crtc_state *old_crtc_state,
+						   struct intel_crtc_state *new_crtc_state)
+{
+	struct intel_crtc *slave_crtc = intel_get_slave_crtc(new_crtc_state);
+	struct intel_crtc_state *new_slave_crtc_state =
+		intel_atomic_get_new_crtc_state(state, slave_crtc);
+	struct intel_crtc_state *old_slave_crtc_state =
+		intel_atomic_get_old_crtc_state(state, slave_crtc);
+
+	WARN_ON(!slave_crtc || !new_slave_crtc_state ||
+		!old_slave_crtc_state);
+
+	/* Disable Slave first */
+	intel_pre_plane_update(old_slave_crtc_state, new_slave_crtc_state);
+	if (old_slave_crtc_state->base.active)
+		intel_old_crtc_state_disables(state,
+					      old_slave_crtc_state,
+					      new_slave_crtc_state,
+					      slave_crtc);
+
+	/* Disable Master */
+	intel_pre_plane_update(old_crtc_state, new_crtc_state);
+	if (old_crtc_state->base.active)
+		intel_old_crtc_state_disables(state,
+					      old_crtc_state,
+					      new_crtc_state,
+					      crtc);
+}
+
 static void intel_commit_modeset_disables(struct intel_atomic_state *state)
 {
 	struct intel_crtc_state *new_crtc_state, *old_crtc_state;
@@ -14128,13 +14159,28 @@ static void intel_commit_modeset_disables(struct intel_atomic_state *state)
 		if (!needs_modeset(new_crtc_state))
 			continue;
 
-		intel_pre_plane_update(old_crtc_state, new_crtc_state);
+		/* In case of Transcoder port Sync master slave CRTCs can be
+		 * assigned in any order and we need to make sure that
+		 * slave CRTCs are disabled first and then master CRTC since
+		 * Slave vblanks are masked till Master Vblanks.
+		 */
+		if (is_trans_port_sync_mode(new_crtc_state)) {
+			if (is_trans_port_sync_master(new_crtc_state))
+				intel_trans_port_sync_modeset_disables(state,
+								       crtc,
+								       old_crtc_state,
+								       new_crtc_state);
+			else
+				continue;
+		} else {
+			intel_pre_plane_update(old_crtc_state, new_crtc_state);
 
-		if (old_crtc_state->base.active)
-			intel_old_crtc_state_disables(state,
-						      old_crtc_state,
-						      new_crtc_state,
-						      crtc);
+			if (old_crtc_state->base.active)
+				intel_old_crtc_state_disables(state,
+							      old_crtc_state,
+							      new_crtc_state,
+							      crtc);
+		}
 	}
 }
 
-- 
2.19.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

^ permalink raw reply related	[flat|nested] 18+ messages in thread

end of thread, other threads:[~2019-10-16 18:45 UTC | newest]

Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-15 23:05 [PATCH v8 0/6] Enable Transcoder port sync for Tiled displays Manasi Navare
2019-10-15 23:05 ` [PATCH v8 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
2019-10-15 23:24   ` [PATCH v9 " Manasi Navare
2019-10-15 23:05 ` [PATCH v8 2/6] drm/i915/display/icl: Enable TRANSCODER PORT SYNC for tiled displays across separate ports Manasi Navare
2019-10-15 23:05 ` [PATCH v8 3/6] drm/i915/display/icl: HW state readout for transcoder port sync config Manasi Navare
2019-10-15 23:05 ` [PATCH v8 4/6] drm/i915/display/icl: Enable master-slaves in trans port sync Manasi Navare
2019-10-15 23:05 ` [PATCH v8 5/6] drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence Manasi Navare
2019-10-15 23:05 ` [PATCH v8 6/6] drm/i915/display/icl: In port sync mode disable slaves first then master Manasi Navare
2019-10-15 23:20 ` [PATCH v9 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
2019-10-16  1:02 ` ✗ Fi.CI.BAT: failure for Enable Transcoder port sync for Tiled displays (rev2) Patchwork
2019-10-16 14:20   ` Ville Syrjälä
2019-10-16 18:13     ` Manasi Navare
2019-10-16 18:47 ` [PATCH v10 1/6] drm/i915/display/icl: Save Master transcoder in slave's crtc_state for Transcoder Port Sync Manasi Navare
2019-10-16 18:47 ` [PATCH v10 2/6] drm/i915/display/icl: Enable TRANSCODER PORT SYNC for tiled displays across separate ports Manasi Navare
2019-10-16 18:47 ` [PATCH v10 3/6] drm/i915/display/icl: HW state readout for transcoder port sync config Manasi Navare
2019-10-16 18:47 ` [PATCH v10 4/6] drm/i915/display/icl: Enable master-slaves in trans port sync Manasi Navare
2019-10-16 18:47 ` [PATCH v10 5/6] drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence Manasi Navare
2019-10-16 18:47 ` [PATCH v10 6/6] drm/i915/display/icl: In port sync mode disable slaves first then master Manasi Navare

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.