All of lore.kernel.org
 help / color / mirror / Atom feed
From: Heiko Stuebner <heiko@sntech.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 03/12] pinctrl: rockchip: add px30 pinctrl driver
Date: Fri, 25 Oct 2019 01:27:54 +0200	[thread overview]
Message-ID: <20191024232803.10338-4-heiko@sntech.de> (raw)
In-Reply-To: <20191024232803.10338-1-heiko@sntech.de>

From: David Wu <david.wu@rock-chips.com>

Add the necessary glue code to allow pinctrl setting on px30 socs.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
---
 drivers/pinctrl/rockchip/Makefile       |   1 +
 drivers/pinctrl/rockchip/pinctrl-px30.c | 368 ++++++++++++++++++++++++
 2 files changed, 369 insertions(+)
 create mode 100644 drivers/pinctrl/rockchip/pinctrl-px30.c

diff --git a/drivers/pinctrl/rockchip/Makefile b/drivers/pinctrl/rockchip/Makefile
index a616d8587f..83913f668f 100644
--- a/drivers/pinctrl/rockchip/Makefile
+++ b/drivers/pinctrl/rockchip/Makefile
@@ -3,6 +3,7 @@
 # Copyright (c) 2017 Rockchip Electronics Co., Ltd
 
 obj-y += pinctrl-rockchip-core.o
+obj-$(CONFIG_ROCKCHIP_PX30) += pinctrl-px30.o
 obj-$(CONFIG_ROCKCHIP_RK3036) += pinctrl-rk3036.o
 obj-$(CONFIG_ROCKCHIP_RK3128) += pinctrl-rk3128.o
 obj-$(CONFIG_ROCKCHIP_RK3188) += pinctrl-rk3188.o
diff --git a/drivers/pinctrl/rockchip/pinctrl-px30.c b/drivers/pinctrl/rockchip/pinctrl-px30.c
new file mode 100644
index 0000000000..bb56ae9fb3
--- /dev/null
+++ b/drivers/pinctrl/rockchip/pinctrl-px30.c
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2019 Rockchip Electronics Co., Ltd
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <dm/pinctrl.h>
+#include <regmap.h>
+#include <syscon.h>
+
+#include "pinctrl-rockchip.h"
+
+static struct rockchip_mux_route_data px30_mux_route_data[] = {
+	{
+		/* cif-d2m0 */
+		.bank_num = 2,
+		.pin = 0,
+		.func = 1,
+		.route_offset = 0x184,
+		.route_val = BIT(16 + 7),
+	}, {
+		/* cif-d2m1 */
+		.bank_num = 3,
+		.pin = 3,
+		.func = 3,
+		.route_offset = 0x184,
+		.route_val = BIT(16 + 7) | BIT(7),
+	}, {
+		/* pdm-m0 */
+		.bank_num = 3,
+		.pin = 22,
+		.func = 2,
+		.route_offset = 0x184,
+		.route_val = BIT(16 + 8),
+	}, {
+		/* pdm-m1 */
+		.bank_num = 2,
+		.pin = 22,
+		.func = 1,
+		.route_offset = 0x184,
+		.route_val = BIT(16 + 8) | BIT(8),
+	}, {
+		/* uart2-rxm0 */
+		.bank_num = 1,
+		.pin = 27,
+		.func = 2,
+		.route_offset = 0x184,
+		.route_val = BIT(16 + 10),
+	}, {
+		/* uart2-rxm1 */
+		.bank_num = 2,
+		.pin = 14,
+		.func = 2,
+		.route_offset = 0x184,
+		.route_val = BIT(16 + 10) | BIT(10),
+	}, {
+		/* uart3-rxm0 */
+		.bank_num = 0,
+		.pin = 17,
+		.func = 2,
+		.route_offset = 0x184,
+		.route_val = BIT(16 + 9),
+	}, {
+		/* uart3-rxm1 */
+		.bank_num = 1,
+		.pin = 15,
+		.func = 2,
+		.route_offset = 0x184,
+		.route_val = BIT(16 + 9) | BIT(9),
+	},
+};
+
+static int px30_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
+{
+	struct rockchip_pinctrl_priv *priv = bank->priv;
+	int iomux_num = (pin / 8);
+	struct regmap *regmap;
+	int reg, ret, mask, mux_type;
+	u8 bit;
+	u32 data, route_reg, route_val;
+
+	regmap = (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU)
+				? priv->regmap_pmu : priv->regmap_base;
+
+	/* get basic quadrupel of mux registers and the correct reg inside */
+	mux_type = bank->iomux[iomux_num].type;
+	reg = bank->iomux[iomux_num].offset;
+	reg += rockchip_get_mux_data(mux_type, pin, &bit, &mask);
+
+	if (bank->route_mask & BIT(pin)) {
+		if (rockchip_get_mux_route(bank, pin, mux, &route_reg,
+					   &route_val)) {
+			ret = regmap_write(regmap, route_reg, route_val);
+			if (ret)
+				return ret;
+		}
+	}
+
+	data = (mask << (bit + 16));
+	data |= (mux & mask) << bit;
+	ret = regmap_write(regmap, reg, data);
+
+	return ret;
+}
+
+#define PX30_PULL_PMU_OFFSET		0x10
+#define PX30_PULL_GRF_OFFSET		0x60
+#define PX30_PULL_BITS_PER_PIN		2
+#define PX30_PULL_PINS_PER_REG		8
+#define PX30_PULL_BANK_STRIDE		16
+
+static void px30_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+				       int pin_num, struct regmap **regmap,
+				       int *reg, u8 *bit)
+{
+	struct rockchip_pinctrl_priv *priv = bank->priv;
+
+	/* The first 32 pins of the first bank are located in PMU */
+	if (bank->bank_num == 0) {
+		*regmap = priv->regmap_pmu;
+		*reg = PX30_PULL_PMU_OFFSET;
+	} else {
+		*regmap = priv->regmap_base;
+		*reg = PX30_PULL_GRF_OFFSET;
+
+		/* correct the offset, as we're starting with the 2nd bank */
+		*reg -= 0x10;
+		*reg += bank->bank_num * PX30_PULL_BANK_STRIDE;
+	}
+
+	*reg += ((pin_num / PX30_PULL_PINS_PER_REG) * 4);
+	*bit = (pin_num % PX30_PULL_PINS_PER_REG);
+	*bit *= PX30_PULL_BITS_PER_PIN;
+}
+
+static int px30_set_pull(struct rockchip_pin_bank *bank,
+			 int pin_num, int pull)
+{
+	struct regmap *regmap;
+	int reg, ret;
+	u8 bit, type;
+	u32 data;
+
+	if (pull == PIN_CONFIG_BIAS_PULL_PIN_DEFAULT)
+		return -ENOTSUPP;
+
+	px30_calc_pull_reg_and_bit(bank, pin_num, &regmap, &reg, &bit);
+	type = bank->pull_type[pin_num / 8];
+	ret = rockchip_translate_pull_value(type, pull);
+	if (ret < 0) {
+		debug("unsupported pull setting %d\n", pull);
+		return ret;
+	}
+
+	/* enable the write to the equivalent lower bits */
+	data = ((1 << ROCKCHIP_PULL_BITS_PER_PIN) - 1) << (bit + 16);
+	data |= (ret << bit);
+	ret = regmap_write(regmap, reg, data);
+
+	return ret;
+}
+
+#define PX30_DRV_PMU_OFFSET		0x20
+#define PX30_DRV_GRF_OFFSET		0xf0
+#define PX30_DRV_BITS_PER_PIN		2
+#define PX30_DRV_PINS_PER_REG		8
+#define PX30_DRV_BANK_STRIDE		16
+
+static void px30_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+				      int pin_num, struct regmap **regmap,
+				      int *reg, u8 *bit)
+{
+	struct rockchip_pinctrl_priv *priv = bank->priv;
+
+	/* The first 32 pins of the first bank are located in PMU */
+	if (bank->bank_num == 0) {
+		*regmap = priv->regmap_pmu;
+		*reg = PX30_DRV_PMU_OFFSET;
+	} else {
+		*regmap = priv->regmap_base;
+		*reg = PX30_DRV_GRF_OFFSET;
+
+		/* correct the offset, as we're starting with the 2nd bank */
+		*reg -= 0x10;
+		*reg += bank->bank_num * PX30_DRV_BANK_STRIDE;
+	}
+
+	*reg += ((pin_num / PX30_DRV_PINS_PER_REG) * 4);
+	*bit = (pin_num % PX30_DRV_PINS_PER_REG);
+	*bit *= PX30_DRV_BITS_PER_PIN;
+}
+
+static int px30_set_drive(struct rockchip_pin_bank *bank,
+			  int pin_num, int strength)
+{
+	struct regmap *regmap;
+	int reg, ret;
+	u32 data, rmask_bits, temp;
+	u8 bit;
+	int drv_type = bank->drv[pin_num / 8].drv_type;
+
+	px30_calc_drv_reg_and_bit(bank, pin_num, &regmap, &reg, &bit);
+	ret = rockchip_translate_drive_value(drv_type, strength);
+	if (ret < 0) {
+		debug("unsupported driver strength %d\n", strength);
+		return ret;
+	}
+
+	switch (drv_type) {
+	case DRV_TYPE_IO_1V8_3V0_AUTO:
+	case DRV_TYPE_IO_3V3_ONLY:
+		rmask_bits = ROCKCHIP_DRV_3BITS_PER_PIN;
+		switch (bit) {
+		case 0 ... 12:
+			/* regular case, nothing to do */
+			break;
+		case 15:
+			/*
+			 * drive-strength offset is special, as it is spread
+			 * over 2 registers, the bit data[15] contains bit 0
+			 * of the value while temp[1:0] contains bits 2 and 1
+			 */
+			data = (ret & 0x1) << 15;
+			temp = (ret >> 0x1) & 0x3;
+
+			data |= BIT(31);
+			ret = regmap_write(regmap, reg, data);
+			if (ret)
+				return ret;
+
+			temp |= (0x3 << 16);
+			reg += 0x4;
+			ret = regmap_write(regmap, reg, temp);
+
+			return ret;
+		case 18 ... 21:
+			/* setting fully enclosed in the second register */
+			reg += 4;
+			bit -= 16;
+			break;
+		default:
+			debug("unsupported bit: %d for pinctrl drive type: %d\n",
+			      bit, drv_type);
+			return -EINVAL;
+		}
+		break;
+	case DRV_TYPE_IO_DEFAULT:
+	case DRV_TYPE_IO_1V8_OR_3V0:
+	case DRV_TYPE_IO_1V8_ONLY:
+		rmask_bits = ROCKCHIP_DRV_BITS_PER_PIN;
+		break;
+	default:
+		debug("unsupported pinctrl drive type: %d\n",
+		      drv_type);
+		return -EINVAL;
+	}
+
+	/* enable the write to the equivalent lower bits */
+	data = ((1 << rmask_bits) - 1) << (bit + 16);
+	data |= (ret << bit);
+	ret = regmap_write(regmap, reg, data);
+
+	return ret;
+}
+
+#define PX30_SCHMITT_PMU_OFFSET			0x38
+#define PX30_SCHMITT_GRF_OFFSET			0xc0
+#define PX30_SCHMITT_PINS_PER_PMU_REG		16
+#define PX30_SCHMITT_BANK_STRIDE		16
+#define PX30_SCHMITT_PINS_PER_GRF_REG		8
+
+static int px30_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
+					 int pin_num,
+					 struct regmap **regmap,
+					 int *reg, u8 *bit)
+{
+	struct rockchip_pinctrl_priv *priv = bank->priv;
+	int pins_per_reg;
+
+	if (bank->bank_num == 0) {
+		*regmap = priv->regmap_pmu;
+		*reg = PX30_SCHMITT_PMU_OFFSET;
+		pins_per_reg = PX30_SCHMITT_PINS_PER_PMU_REG;
+	} else {
+		*regmap = priv->regmap_base;
+		*reg = PX30_SCHMITT_GRF_OFFSET;
+		pins_per_reg = PX30_SCHMITT_PINS_PER_GRF_REG;
+		*reg += (bank->bank_num - 1) * PX30_SCHMITT_BANK_STRIDE;
+	}
+	*reg += ((pin_num / pins_per_reg) * 4);
+	*bit = pin_num % pins_per_reg;
+
+	return 0;
+}
+
+static int px30_set_schmitt(struct rockchip_pin_bank *bank,
+			    int pin_num, int enable)
+{
+	struct regmap *regmap;
+	int reg;
+	u8 bit;
+	u32 data;
+
+	px30_calc_schmitt_reg_and_bit(bank, pin_num, &regmap, &reg, &bit);
+	/* enable the write to the equivalent lower bits */
+	data = BIT(bit + 16) | (enable << bit);
+
+	return regmap_write(regmap, reg, data);
+}
+
+static struct rockchip_pin_bank px30_pin_banks[] = {
+	PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0", IOMUX_SOURCE_PMU,
+					     IOMUX_SOURCE_PMU,
+					     IOMUX_SOURCE_PMU,
+					     IOMUX_SOURCE_PMU
+			    ),
+	PIN_BANK_IOMUX_FLAGS(1, 32, "gpio1", IOMUX_WIDTH_4BIT,
+					     IOMUX_WIDTH_4BIT,
+					     IOMUX_WIDTH_4BIT,
+					     IOMUX_WIDTH_4BIT
+			    ),
+	PIN_BANK_IOMUX_FLAGS(2, 32, "gpio2", IOMUX_WIDTH_4BIT,
+					     IOMUX_WIDTH_4BIT,
+					     IOMUX_WIDTH_4BIT,
+					     IOMUX_WIDTH_4BIT
+			    ),
+	PIN_BANK_IOMUX_FLAGS(3, 32, "gpio3", IOMUX_WIDTH_4BIT,
+					     IOMUX_WIDTH_4BIT,
+					     IOMUX_WIDTH_4BIT,
+					     IOMUX_WIDTH_4BIT
+			    ),
+};
+
+static struct rockchip_pin_ctrl px30_pin_ctrl = {
+	.pin_banks		= px30_pin_banks,
+	.nr_banks		= ARRAY_SIZE(px30_pin_banks),
+	.grf_mux_offset		= 0x0,
+	.pmu_mux_offset		= 0x0,
+	.grf_drv_offset		= 0xf0,
+	.pmu_drv_offset		= 0x20,
+	.iomux_routes		= px30_mux_route_data,
+	.niomux_routes		= ARRAY_SIZE(px30_mux_route_data),
+	.set_mux		= px30_set_mux,
+	.set_pull		= px30_set_pull,
+	.set_drive		= px30_set_drive,
+	.set_schmitt		= px30_set_schmitt,
+};
+
+static const struct udevice_id px30_pinctrl_ids[] = {
+	{
+		.compatible = "rockchip,px30-pinctrl",
+		.data = (ulong)&px30_pin_ctrl
+	},
+	{ }
+};
+
+U_BOOT_DRIVER(pinctrl_px30) = {
+	.name		= "rockchip_px30_pinctrl",
+	.id		= UCLASS_PINCTRL,
+	.of_match	= px30_pinctrl_ids,
+	.priv_auto_alloc_size = sizeof(struct rockchip_pinctrl_priv),
+	.ops		= &rockchip_pinctrl_ops,
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
+	.bind		= dm_scan_fdt_dev,
+#endif
+	.probe		= rockchip_pinctrl_probe,
+};
-- 
2.23.0

  parent reply	other threads:[~2019-10-24 23:27 UTC|newest]

Thread overview: 28+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-24 23:27 [U-Boot] [PATCH 00/12] rockchip: add support for px30 Heiko Stuebner
2019-10-24 23:27 ` [U-Boot] [PATCH 01/12] spl: separate SPL_FRAMEWORK config for spl and tpl Heiko Stuebner
2019-10-25  1:55   ` Kever Yang
2019-10-24 23:27 ` [U-Boot] [PATCH 02/12] rockchip: add core px30 headers Heiko Stuebner
2019-10-25  2:04   ` Kever Yang
2019-10-24 23:27 ` Heiko Stuebner [this message]
2019-10-25  2:07   ` [U-Boot] [PATCH 03/12] pinctrl: rockchip: add px30 pinctrl driver Kever Yang
2019-10-24 23:27 ` [U-Boot] [PATCH 04/12] rockchip: clk: add px30 clock driver Heiko Stuebner
2019-10-24 23:27 ` [U-Boot] [PATCH 05/12] net: gmac_rockchip: add support for px30 Heiko Stuebner
2019-10-25  2:09   ` Kever Yang
2019-10-24 23:27 ` [U-Boot] [PATCH 06/12] rockchip: mkimage: " Heiko Stuebner
2019-10-25  2:09   ` Kever Yang
2019-10-24 23:27 ` [U-Boot] [PATCH 07/12] misc: add driver for the Rockchip otp controller Heiko Stuebner
2019-10-25  2:10   ` Kever Yang
2019-10-24 23:27 ` [U-Boot] [PATCH 08/12] rockchip: misc: read cpuid either from efuse or otp Heiko Stuebner
2019-10-25  2:11   ` Kever Yang
2019-10-24 23:28 ` [U-Boot] [PATCH 09/12] rockchip: ram: add dm-based sdram driver Heiko Stuebner
2019-10-24 23:28 ` [U-Boot] [PATCH 10/12] rockchip: add px30 devicetrees Heiko Stuebner
2019-10-25  2:39   ` Kever Yang
2019-10-24 23:28 ` [U-Boot] [PATCH 11/12] rockchip: add px30 architecture core Heiko Stuebner
2019-10-25  2:49   ` Kever Yang
2019-10-25  7:47     ` Heiko Stübner
2019-11-10 14:13       ` Kever Yang
2019-11-10 14:46         ` Heiko Stuebner
2019-10-24 23:28 ` [U-Boot] [PATCH 12/12] rockchip: add px30-evb board Heiko Stuebner
2019-10-25  2:51   ` Kever Yang
2019-10-25  1:44 ` [U-Boot] [PATCH 00/12] rockchip: add support for px30 Kever Yang
2019-11-18  2:57 ` Kever Yang

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191024232803.10338-4-heiko@sntech.de \
    --to=heiko@sntech.de \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.