* [PATCH 0/2] STMFX pinctrl definition updates
@ 2019-10-29 12:46 ` Amelie Delaunay
0 siblings, 0 replies; 9+ messages in thread
From: Amelie Delaunay @ 2019-10-29 12:46 UTC (permalink / raw)
To: Maxime Coquelin, Alexandre Torgue, Rob Herring, Mark Rutland
Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, Amelie Delaunay
Since a502b343eb ("pinctrl: stmfx: update pinconf settings"), pin
confuguration has been fixed in STMFX pinctrl driver. Moreover, gpiolib now
fully handles "push-pull" configuration.
This series cleans up stm32mp157c-ev1 stmfx pins use.
Amelie Delaunay (2):
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
arch/arm/boot/dts/stm32mp157c-ev1.dts | 13 ++-----------
1 file changed, 2 insertions(+), 11 deletions(-)
--
2.17.1
^ permalink raw reply [flat|nested] 9+ messages in thread* [PATCH 0/2] STMFX pinctrl definition updates
@ 2019-10-29 12:46 ` Amelie Delaunay
0 siblings, 0 replies; 9+ messages in thread
From: Amelie Delaunay @ 2019-10-29 12:46 UTC (permalink / raw)
To: Maxime Coquelin, Alexandre Torgue, Rob Herring, Mark Rutland
Cc: devicetree, Amelie Delaunay, linux-stm32, linux-arm-kernel, linux-kernel
Since a502b343eb ("pinctrl: stmfx: update pinconf settings"), pin
confuguration has been fixed in STMFX pinctrl driver. Moreover, gpiolib now
fully handles "push-pull" configuration.
This series cleans up stm32mp157c-ev1 stmfx pins use.
Amelie Delaunay (2):
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
arch/arm/boot/dts/stm32mp157c-ev1.dts | 13 ++-----------
1 file changed, 2 insertions(+), 11 deletions(-)
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 9+ messages in thread* [PATCH 1/2] ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
2019-10-29 12:46 ` Amelie Delaunay
@ 2019-10-29 12:46 ` Amelie Delaunay
-1 siblings, 0 replies; 9+ messages in thread
From: Amelie Delaunay @ 2019-10-29 12:46 UTC (permalink / raw)
To: Maxime Coquelin, Alexandre Torgue, Rob Herring, Mark Rutland
Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, Amelie Delaunay
"push-pull" configuration is now fully handled by the gpiolib and the
STMFX pinctrl driver. There is no longer need to declare a pinctrl group
to only configure "push-pull" setting for the line. It is done directly by
the gpiolib.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 12 ++----------
1 file changed, 2 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 2baae5f25e2c..3f7fcba3a516 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -182,14 +182,12 @@
ov5640: camera@3c {
compatible = "ovti,ov5640";
- pinctrl-names = "default";
- pinctrl-0 = <&ov5640_pins>;
reg = <0x3c>;
clocks = <&clk_ext_camera>;
clock-names = "xclk";
DOVDD-supply = <&v2v8>;
- powerdown-gpios = <&stmfx_pinctrl 18 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&stmfx_pinctrl 19 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
+ reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
rotation = <180>;
status = "okay";
@@ -225,12 +223,6 @@
drive-push-pull;
bias-pull-down;
};
-
- ov5640_pins: camera {
- pins = "agpio2", "agpio3"; /* stmfx pins 18 & 19 */
- drive-push-pull;
- output-low;
- };
};
};
};
--
2.17.1
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 1/2] ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
@ 2019-10-29 12:46 ` Amelie Delaunay
0 siblings, 0 replies; 9+ messages in thread
From: Amelie Delaunay @ 2019-10-29 12:46 UTC (permalink / raw)
To: Maxime Coquelin, Alexandre Torgue, Rob Herring, Mark Rutland
Cc: devicetree, Amelie Delaunay, linux-stm32, linux-arm-kernel, linux-kernel
"push-pull" configuration is now fully handled by the gpiolib and the
STMFX pinctrl driver. There is no longer need to declare a pinctrl group
to only configure "push-pull" setting for the line. It is done directly by
the gpiolib.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 12 ++----------
1 file changed, 2 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 2baae5f25e2c..3f7fcba3a516 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -182,14 +182,12 @@
ov5640: camera@3c {
compatible = "ovti,ov5640";
- pinctrl-names = "default";
- pinctrl-0 = <&ov5640_pins>;
reg = <0x3c>;
clocks = <&clk_ext_camera>;
clock-names = "xclk";
DOVDD-supply = <&v2v8>;
- powerdown-gpios = <&stmfx_pinctrl 18 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&stmfx_pinctrl 19 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
+ reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
rotation = <180>;
status = "okay";
@@ -225,12 +223,6 @@
drive-push-pull;
bias-pull-down;
};
-
- ov5640_pins: camera {
- pins = "agpio2", "agpio3"; /* stmfx pins 18 & 19 */
- drive-push-pull;
- output-low;
- };
};
};
};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/2] ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
2019-10-29 12:46 ` Amelie Delaunay
@ 2019-10-29 12:46 ` Amelie Delaunay
-1 siblings, 0 replies; 9+ messages in thread
From: Amelie Delaunay @ 2019-10-29 12:46 UTC (permalink / raw)
To: Maxime Coquelin, Alexandre Torgue, Rob Herring, Mark Rutland
Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, Amelie Delaunay
Pins used for joystick are all configured as input. "push-pull" is not a
valid setting for an input pin.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 3f7fcba3a516..3789312c8539 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -220,7 +220,6 @@
joystick_pins: joystick {
pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
- drive-push-pull;
bias-pull-down;
};
};
--
2.17.1
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 2/2] ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
@ 2019-10-29 12:46 ` Amelie Delaunay
0 siblings, 0 replies; 9+ messages in thread
From: Amelie Delaunay @ 2019-10-29 12:46 UTC (permalink / raw)
To: Maxime Coquelin, Alexandre Torgue, Rob Herring, Mark Rutland
Cc: devicetree, Amelie Delaunay, linux-stm32, linux-arm-kernel, linux-kernel
Pins used for joystick are all configured as input. "push-pull" is not a
valid setting for an input pin.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 3f7fcba3a516..3789312c8539 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -220,7 +220,6 @@
joystick_pins: joystick {
pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
- drive-push-pull;
bias-pull-down;
};
};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 0/2] STMFX GPIO consumers update
@ 2019-07-25 11:36 Amelie Delaunay
2019-07-25 11:36 ` Amelie Delaunay
0 siblings, 1 reply; 9+ messages in thread
From: Amelie Delaunay @ 2019-07-25 11:36 UTC (permalink / raw)
To: Maxime Coquelin, Alexandre Torgue, Rob Herring, Mark Rutland
Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, Amelie Delaunay
This series depends on a STMFX pinctrl driver update
(https://lkml.org/lkml/2019/7/25/536).
Now, STMFX GPIO consumers can use standard GPIO bindings.
Alexandre Torgue (2):
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: change pinctrl definition for joystick pins on
stm32mp157c-ev1
arch/arm/boot/dts/stm32mp157c-ev1.dts | 13 ++-----------
1 file changed, 2 insertions(+), 11 deletions(-)
--
2.7.4
^ permalink raw reply [flat|nested] 9+ messages in thread* [PATCH 1/2] ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
2019-07-25 11:36 [PATCH 0/2] STMFX GPIO consumers update Amelie Delaunay
2019-07-25 11:36 ` Amelie Delaunay
@ 2019-07-25 11:36 ` Amelie Delaunay
0 siblings, 0 replies; 9+ messages in thread
From: Amelie Delaunay @ 2019-07-25 11:36 UTC (permalink / raw)
To: Maxime Coquelin, Alexandre Torgue, Rob Herring, Mark Rutland
Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, Amelie Delaunay
From: Alexandre Torgue <alexandre.torgue@st.com>
"push-pull" configuration is now fully handled by the gpiolib and the
STMFX pinctrl driver. There is no longer need to declare a pinctrl group
to only configure "push-pull" setting for the line. It is done directly by
the gpiolib.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 12 ++----------
1 file changed, 2 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 9ab25da..e4b04dd 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -182,14 +182,12 @@
ov5640: camera@3c {
compatible = "ovti,ov5640";
- pinctrl-names = "default";
- pinctrl-0 = <&ov5640_pins>;
reg = <0x3c>;
clocks = <&clk_ext_camera>;
clock-names = "xclk";
DOVDD-supply = <&v2v8>;
- powerdown-gpios = <&stmfx_pinctrl 18 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&stmfx_pinctrl 19 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
+ reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
rotation = <180>;
status = "okay";
@@ -225,12 +223,6 @@
drive-push-pull;
bias-pull-down;
};
-
- ov5640_pins: camera {
- pins = "agpio2", "agpio3"; /* stmfx pins 18 & 19 */
- drive-push-pull;
- output-low;
- };
};
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 1/2] ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
@ 2019-07-25 11:36 ` Amelie Delaunay
0 siblings, 0 replies; 9+ messages in thread
From: Amelie Delaunay @ 2019-07-25 11:36 UTC (permalink / raw)
To: Maxime Coquelin, Alexandre Torgue, Rob Herring, Mark Rutland
Cc: devicetree, Amelie Delaunay, linux-stm32, linux-arm-kernel, linux-kernel
From: Alexandre Torgue <alexandre.torgue@st.com>
"push-pull" configuration is now fully handled by the gpiolib and the
STMFX pinctrl driver. There is no longer need to declare a pinctrl group
to only configure "push-pull" setting for the line. It is done directly by
the gpiolib.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 12 ++----------
1 file changed, 2 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 9ab25da..e4b04dd 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -182,14 +182,12 @@
ov5640: camera@3c {
compatible = "ovti,ov5640";
- pinctrl-names = "default";
- pinctrl-0 = <&ov5640_pins>;
reg = <0x3c>;
clocks = <&clk_ext_camera>;
clock-names = "xclk";
DOVDD-supply = <&v2v8>;
- powerdown-gpios = <&stmfx_pinctrl 18 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&stmfx_pinctrl 19 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
+ reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
rotation = <180>;
status = "okay";
@@ -225,12 +223,6 @@
drive-push-pull;
bias-pull-down;
};
-
- ov5640_pins: camera {
- pins = "agpio2", "agpio3"; /* stmfx pins 18 & 19 */
- drive-push-pull;
- output-low;
- };
};
};
};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 1/2] ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
@ 2019-07-25 11:36 ` Amelie Delaunay
0 siblings, 0 replies; 9+ messages in thread
From: Amelie Delaunay @ 2019-07-25 11:36 UTC (permalink / raw)
To: Maxime Coquelin, Alexandre Torgue, Rob Herring, Mark Rutland
Cc: linux-stm32, linux-arm-kernel, devicetree, linux-kernel, Amelie Delaunay
From: Alexandre Torgue <alexandre.torgue@st.com>
"push-pull" configuration is now fully handled by the gpiolib and the
STMFX pinctrl driver. There is no longer need to declare a pinctrl group
to only configure "push-pull" setting for the line. It is done directly by
the gpiolib.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 12 ++----------
1 file changed, 2 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 9ab25da..e4b04dd 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -182,14 +182,12 @@
ov5640: camera@3c {
compatible = "ovti,ov5640";
- pinctrl-names = "default";
- pinctrl-0 = <&ov5640_pins>;
reg = <0x3c>;
clocks = <&clk_ext_camera>;
clock-names = "xclk";
DOVDD-supply = <&v2v8>;
- powerdown-gpios = <&stmfx_pinctrl 18 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&stmfx_pinctrl 19 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
+ reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
rotation = <180>;
status = "okay";
@@ -225,12 +223,6 @@
drive-push-pull;
bias-pull-down;
};
-
- ov5640_pins: camera {
- pins = "agpio2", "agpio3"; /* stmfx pins 18 & 19 */
- drive-push-pull;
- output-low;
- };
};
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 9+ messages in thread
end of thread, other threads:[~2019-10-29 12:47 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-29 12:46 [PATCH 0/2] STMFX pinctrl definition updates Amelie Delaunay
2019-10-29 12:46 ` Amelie Delaunay
2019-10-29 12:46 ` [PATCH 1/2] ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1 Amelie Delaunay
2019-10-29 12:46 ` Amelie Delaunay
2019-10-29 12:46 ` [PATCH 2/2] ARM: dts: stm32: change joystick " Amelie Delaunay
2019-10-29 12:46 ` Amelie Delaunay
-- strict thread matches above, loose matches on Subject: below --
2019-07-25 11:36 [PATCH 0/2] STMFX GPIO consumers update Amelie Delaunay
2019-07-25 11:36 ` [PATCH 1/2] ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1 Amelie Delaunay
2019-07-25 11:36 ` Amelie Delaunay
2019-07-25 11:36 ` Amelie Delaunay
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.