[PATCH v3 00/13] phy: usb: Updates to Broadcom STB USB PHY driver

[PATCH v3 00/13] phy: usb: Updates to Broadcom STB USB PHY driver

[Al Cooper]

This patchset contains various updates to the Broadcom STB USB Driver.
The updates include:
- Add support for 7216 and 7211 Broadcom SoCs which use the new
  Synopsis USB Controller.
- Add support for USB Wake
- Add various bug fixes.

v3 - Rebase to v5.5-rc1

v2 - Changes based on review feedback
- Add vendor prefix to DT property "syscon-piarbctl"
- Use standard "wakeup" instead of "wake" for DT "interrupt-names"

Al Cooper (13):
  phy: usb: EHCI DMA may lose a burst of DMA data for 7255xA0 family
  phy: usb: Get all drivers that use USB clks using correct
    enable/disable
  phy: usb: Put USB phys into IDDQ on suspend to save power in S2 mode
  phy: usb: Add "wake on" functionality
  phy: usb: Restructure in preparation for adding 7216 USB support
  dt-bindings: Add Broadcom STB USB PHY binding document
  phy: usb: Add support for new Synopsis USB controller on the 7216
  phy: usb: Add support for new Synopsis USB controller on the 7211b0
  phy: usb: fix driver to defer on clk_get defer
  phy: usb: PHY's MDIO registers not accessible without device installed
  phy: usb: bdc: Fix occasional failure with BDC on 7211
  phy: usb: USB driver is crashing during S3 resume on 7216
  phy: usb: Add support for wake and USB low power mode for 7211 S2/S5

 .../bindings/phy/brcm,brcmstb-usb-phy.txt     |  69 ++-
 drivers/phy/broadcom/Makefile                 |   2 +-
 .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 414 ++++++++++++++++++
 drivers/phy/broadcom/phy-brcm-usb-init.c      | 226 +++++-----
 drivers/phy/broadcom/phy-brcm-usb-init.h      | 148 ++++++-
 drivers/phy/broadcom/phy-brcm-usb.c           | 269 ++++++++++--
 6 files changed, 943 insertions(+), 185 deletions(-)
 create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c

-- 
2.17.1

[PATCH v3 00/13] phy: usb: Updates to Broadcom STB USB PHY driver

[Al Cooper]

This patchset contains various updates to the Broadcom STB USB Driver.
The updates include:
- Add support for 7216 and 7211 Broadcom SoCs which use the new
  Synopsis USB Controller.
- Add support for USB Wake
- Add various bug fixes.

v3 - Rebase to v5.5-rc1

v2 - Changes based on review feedback
- Add vendor prefix to DT property "syscon-piarbctl"
- Use standard "wakeup" instead of "wake" for DT "interrupt-names"

Al Cooper (13):
  phy: usb: EHCI DMA may lose a burst of DMA data for 7255xA0 family
  phy: usb: Get all drivers that use USB clks using correct
    enable/disable
  phy: usb: Put USB phys into IDDQ on suspend to save power in S2 mode
  phy: usb: Add "wake on" functionality
  phy: usb: Restructure in preparation for adding 7216 USB support
  dt-bindings: Add Broadcom STB USB PHY binding document
  phy: usb: Add support for new Synopsis USB controller on the 7216
  phy: usb: Add support for new Synopsis USB controller on the 7211b0
  phy: usb: fix driver to defer on clk_get defer
  phy: usb: PHY's MDIO registers not accessible without device installed
  phy: usb: bdc: Fix occasional failure with BDC on 7211
  phy: usb: USB driver is crashing during S3 resume on 7216
  phy: usb: Add support for wake and USB low power mode for 7211 S2/S5

 .../bindings/phy/brcm,brcmstb-usb-phy.txt     |  69 ++-
 drivers/phy/broadcom/Makefile                 |   2 +-
 .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 414 ++++++++++++++++++
 drivers/phy/broadcom/phy-brcm-usb-init.c      | 226 +++++-----
 drivers/phy/broadcom/phy-brcm-usb-init.h      | 148 ++++++-
 drivers/phy/broadcom/phy-brcm-usb.c           | 269 ++++++++++--
 6 files changed, 943 insertions(+), 185 deletions(-)
 create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 01/13] phy: usb: EHCI DMA may lose a burst of DMA data for 7255xA0 family

[Al Cooper]

When the EHCI controller received a 512 byte USB packet that
had to be broken into 2 256 byte bursts across the SCB bus AND
there was a following 512 byte USB packet, the second burst of
data from the first packet was sometimes being lost. If the
burst size was changed to 128 bytes via the EBR_SCB_SIZE field
in the USB_CTRL_EBRIDGE register we'd see the 4th 128 byte burst
of the first packet being lost. This problem became much worse
if other threads were running that accessed memory, like a memcpy
test. Setting the EBR_SCB_SIZE to 512, which prevents breaking
the EHCI USB packet (max size of 512 bytes) into bursts, fixed
the problem.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb-init.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index 91b5b09589d6..bd473d12ab28 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -42,6 +42,7 @@
 #define   USB_CTRL_PLL_CTL_PLL_IDDQ_PWRDN_MASK		0x80000000 /* option */
 #define USB_CTRL_EBRIDGE		0x0c
 #define   USB_CTRL_EBRIDGE_ESTOP_SCB_REQ_MASK		0x00020000 /* option */
+#define   USB_CTRL_EBRIDGE_EBR_SCB_SIZE_MASK		0x00000f80 /* option */
 #define USB_CTRL_OBRIDGE		0x10
 #define   USB_CTRL_OBRIDGE_LS_KEEP_ALIVE_MASK		0x08000000
 #define USB_CTRL_MDIO			0x14
@@ -176,6 +177,7 @@ static const struct id_to_type id_to_type_table[] = {
 	{ 0x33900000, BRCM_FAMILY_3390A0 },
 	{ 0x72500010, BRCM_FAMILY_7250B0 },
 	{ 0x72600000, BRCM_FAMILY_7260A0 },
+	{ 0x72550000, BRCM_FAMILY_7260A0 },
 	{ 0x72680000, BRCM_FAMILY_7271A0 },
 	{ 0x72710000, BRCM_FAMILY_7271A0 },
 	{ 0x73640000, BRCM_FAMILY_7364A0 },
@@ -948,6 +950,17 @@ void brcm_usb_init_eohci(struct brcm_usb_init_params *params)
 	if (params->selected_family == BRCM_FAMILY_7271A0)
 		/* Enable LS keep alive fix for certain keyboards */
 		USB_CTRL_SET(ctrl, OBRIDGE, LS_KEEP_ALIVE);
+
+	if (params->family_id == 0x72550000) {
+		/*
+		 * Make the burst size 512 bytes to fix a hardware bug
+		 * on the 7255a0. See HW7255-24.
+		 */
+		reg = brcmusb_readl(USB_CTRL_REG(ctrl, EBRIDGE));
+		reg &= ~USB_CTRL_MASK(EBRIDGE, EBR_SCB_SIZE);
+		reg |= 0x800;
+		brcmusb_writel(reg, USB_CTRL_REG(ctrl, EBRIDGE));
+	}
 }
 
 void brcm_usb_init_xhci(struct brcm_usb_init_params *params)
-- 
2.17.1

[PATCH v3 01/13] phy: usb: EHCI DMA may lose a burst of DMA data for 7255xA0 family

[Al Cooper]

When the EHCI controller received a 512 byte USB packet that
had to be broken into 2 256 byte bursts across the SCB bus AND
there was a following 512 byte USB packet, the second burst of
data from the first packet was sometimes being lost. If the
burst size was changed to 128 bytes via the EBR_SCB_SIZE field
in the USB_CTRL_EBRIDGE register we'd see the 4th 128 byte burst
of the first packet being lost. This problem became much worse
if other threads were running that accessed memory, like a memcpy
test. Setting the EBR_SCB_SIZE to 512, which prevents breaking
the EHCI USB packet (max size of 512 bytes) into bursts, fixed
the problem.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb-init.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index 91b5b09589d6..bd473d12ab28 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -42,6 +42,7 @@
 #define   USB_CTRL_PLL_CTL_PLL_IDDQ_PWRDN_MASK		0x80000000 /* option */
 #define USB_CTRL_EBRIDGE		0x0c
 #define   USB_CTRL_EBRIDGE_ESTOP_SCB_REQ_MASK		0x00020000 /* option */
+#define   USB_CTRL_EBRIDGE_EBR_SCB_SIZE_MASK		0x00000f80 /* option */
 #define USB_CTRL_OBRIDGE		0x10
 #define   USB_CTRL_OBRIDGE_LS_KEEP_ALIVE_MASK		0x08000000
 #define USB_CTRL_MDIO			0x14
@@ -176,6 +177,7 @@ static const struct id_to_type id_to_type_table[] = {
 	{ 0x33900000, BRCM_FAMILY_3390A0 },
 	{ 0x72500010, BRCM_FAMILY_7250B0 },
 	{ 0x72600000, BRCM_FAMILY_7260A0 },
+	{ 0x72550000, BRCM_FAMILY_7260A0 },
 	{ 0x72680000, BRCM_FAMILY_7271A0 },
 	{ 0x72710000, BRCM_FAMILY_7271A0 },
 	{ 0x73640000, BRCM_FAMILY_7364A0 },
@@ -948,6 +950,17 @@ void brcm_usb_init_eohci(struct brcm_usb_init_params *params)
 	if (params->selected_family == BRCM_FAMILY_7271A0)
 		/* Enable LS keep alive fix for certain keyboards */
 		USB_CTRL_SET(ctrl, OBRIDGE, LS_KEEP_ALIVE);
+
+	if (params->family_id == 0x72550000) {
+		/*
+		 * Make the burst size 512 bytes to fix a hardware bug
+		 * on the 7255a0. See HW7255-24.
+		 */
+		reg = brcmusb_readl(USB_CTRL_REG(ctrl, EBRIDGE));
+		reg &= ~USB_CTRL_MASK(EBRIDGE, EBR_SCB_SIZE);
+		reg |= 0x800;
+		brcmusb_writel(reg, USB_CTRL_REG(ctrl, EBRIDGE));
+	}
 }
 
 void brcm_usb_init_xhci(struct brcm_usb_init_params *params)
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 02/13] phy: usb: Get all drivers that use USB clks using correct enable/disable

[Al Cooper]

The BRCM USB Phy, ohci, ehci and xhci drivers all use the USB clocks
but not all drivers use the clk_prepare_enable/clk_disable_unprepare
versions to enable/disable the clocks. This change gets all drivers
using the prepare version.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb.c | 28 ++++++++++++++--------------
 1 file changed, 14 insertions(+), 14 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index f5c1f2983a1d..217e3702ef4e 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -74,8 +74,8 @@ static int brcm_usb_phy_init(struct phy *gphy)
 	 */
 	mutex_lock(&priv->mutex);
 	if (priv->init_count++ == 0) {
-		clk_enable(priv->usb_20_clk);
-		clk_enable(priv->usb_30_clk);
+		clk_prepare_enable(priv->usb_20_clk);
+		clk_prepare_enable(priv->usb_30_clk);
 		brcm_usb_init_common(&priv->ini);
 	}
 	mutex_unlock(&priv->mutex);
@@ -106,8 +106,8 @@ static int brcm_usb_phy_exit(struct phy *gphy)
 	mutex_lock(&priv->mutex);
 	if (--priv->init_count == 0) {
 		brcm_usb_uninit_common(&priv->ini);
-		clk_disable(priv->usb_20_clk);
-		clk_disable(priv->usb_30_clk);
+		clk_disable_unprepare(priv->usb_20_clk);
+		clk_disable_unprepare(priv->usb_30_clk);
 	}
 	mutex_unlock(&priv->mutex);
 	phy->inited = false;
@@ -360,8 +360,8 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	if (priv->has_eohci)
 		brcm_usb_uninit_eohci(&priv->ini);
 	brcm_usb_uninit_common(&priv->ini);
-	clk_disable(priv->usb_20_clk);
-	clk_disable(priv->usb_30_clk);
+	clk_disable_unprepare(priv->usb_20_clk);
+	clk_disable_unprepare(priv->usb_30_clk);
 
 	phy_provider = devm_of_phy_provider_register(dev, brcm_usb_phy_xlate);
 
@@ -381,8 +381,8 @@ static int brcm_usb_phy_suspend(struct device *dev)
 	struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
 
 	if (priv->init_count) {
-		clk_disable(priv->usb_20_clk);
-		clk_disable(priv->usb_30_clk);
+		clk_disable_unprepare(priv->usb_20_clk);
+		clk_disable_unprepare(priv->usb_30_clk);
 	}
 	return 0;
 }
@@ -391,8 +391,8 @@ static int brcm_usb_phy_resume(struct device *dev)
 {
 	struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
 
-	clk_enable(priv->usb_20_clk);
-	clk_enable(priv->usb_30_clk);
+	clk_prepare_enable(priv->usb_20_clk);
+	clk_prepare_enable(priv->usb_30_clk);
 	brcm_usb_init_ipp(&priv->ini);
 
 	/*
@@ -405,13 +405,13 @@ static int brcm_usb_phy_resume(struct device *dev)
 			brcm_usb_init_eohci(&priv->ini);
 		} else if (priv->has_eohci) {
 			brcm_usb_uninit_eohci(&priv->ini);
-			clk_disable(priv->usb_20_clk);
+			clk_disable_unprepare(priv->usb_20_clk);
 		}
 		if (priv->phys[BRCM_USB_PHY_3_0].inited) {
 			brcm_usb_init_xhci(&priv->ini);
 		} else if (priv->has_xhci) {
 			brcm_usb_uninit_xhci(&priv->ini);
-			clk_disable(priv->usb_30_clk);
+			clk_disable_unprepare(priv->usb_30_clk);
 		}
 	} else {
 		if (priv->has_xhci)
@@ -419,8 +419,8 @@ static int brcm_usb_phy_resume(struct device *dev)
 		if (priv->has_eohci)
 			brcm_usb_uninit_eohci(&priv->ini);
 		brcm_usb_uninit_common(&priv->ini);
-		clk_disable(priv->usb_20_clk);
-		clk_disable(priv->usb_30_clk);
+		clk_disable_unprepare(priv->usb_20_clk);
+		clk_disable_unprepare(priv->usb_30_clk);
 	}
 
 	return 0;
-- 
2.17.1

[PATCH v3 02/13] phy: usb: Get all drivers that use USB clks using correct enable/disable

[Al Cooper]

The BRCM USB Phy, ohci, ehci and xhci drivers all use the USB clocks
but not all drivers use the clk_prepare_enable/clk_disable_unprepare
versions to enable/disable the clocks. This change gets all drivers
using the prepare version.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb.c | 28 ++++++++++++++--------------
 1 file changed, 14 insertions(+), 14 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index f5c1f2983a1d..217e3702ef4e 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -74,8 +74,8 @@ static int brcm_usb_phy_init(struct phy *gphy)
 	 */
 	mutex_lock(&priv->mutex);
 	if (priv->init_count++ == 0) {
-		clk_enable(priv->usb_20_clk);
-		clk_enable(priv->usb_30_clk);
+		clk_prepare_enable(priv->usb_20_clk);
+		clk_prepare_enable(priv->usb_30_clk);
 		brcm_usb_init_common(&priv->ini);
 	}
 	mutex_unlock(&priv->mutex);
@@ -106,8 +106,8 @@ static int brcm_usb_phy_exit(struct phy *gphy)
 	mutex_lock(&priv->mutex);
 	if (--priv->init_count == 0) {
 		brcm_usb_uninit_common(&priv->ini);
-		clk_disable(priv->usb_20_clk);
-		clk_disable(priv->usb_30_clk);
+		clk_disable_unprepare(priv->usb_20_clk);
+		clk_disable_unprepare(priv->usb_30_clk);
 	}
 	mutex_unlock(&priv->mutex);
 	phy->inited = false;
@@ -360,8 +360,8 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	if (priv->has_eohci)
 		brcm_usb_uninit_eohci(&priv->ini);
 	brcm_usb_uninit_common(&priv->ini);
-	clk_disable(priv->usb_20_clk);
-	clk_disable(priv->usb_30_clk);
+	clk_disable_unprepare(priv->usb_20_clk);
+	clk_disable_unprepare(priv->usb_30_clk);
 
 	phy_provider = devm_of_phy_provider_register(dev, brcm_usb_phy_xlate);
 
@@ -381,8 +381,8 @@ static int brcm_usb_phy_suspend(struct device *dev)
 	struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
 
 	if (priv->init_count) {
-		clk_disable(priv->usb_20_clk);
-		clk_disable(priv->usb_30_clk);
+		clk_disable_unprepare(priv->usb_20_clk);
+		clk_disable_unprepare(priv->usb_30_clk);
 	}
 	return 0;
 }
@@ -391,8 +391,8 @@ static int brcm_usb_phy_resume(struct device *dev)
 {
 	struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
 
-	clk_enable(priv->usb_20_clk);
-	clk_enable(priv->usb_30_clk);
+	clk_prepare_enable(priv->usb_20_clk);
+	clk_prepare_enable(priv->usb_30_clk);
 	brcm_usb_init_ipp(&priv->ini);
 
 	/*
@@ -405,13 +405,13 @@ static int brcm_usb_phy_resume(struct device *dev)
 			brcm_usb_init_eohci(&priv->ini);
 		} else if (priv->has_eohci) {
 			brcm_usb_uninit_eohci(&priv->ini);
-			clk_disable(priv->usb_20_clk);
+			clk_disable_unprepare(priv->usb_20_clk);
 		}
 		if (priv->phys[BRCM_USB_PHY_3_0].inited) {
 			brcm_usb_init_xhci(&priv->ini);
 		} else if (priv->has_xhci) {
 			brcm_usb_uninit_xhci(&priv->ini);
-			clk_disable(priv->usb_30_clk);
+			clk_disable_unprepare(priv->usb_30_clk);
 		}
 	} else {
 		if (priv->has_xhci)
@@ -419,8 +419,8 @@ static int brcm_usb_phy_resume(struct device *dev)
 		if (priv->has_eohci)
 			brcm_usb_uninit_eohci(&priv->ini);
 		brcm_usb_uninit_common(&priv->ini);
-		clk_disable(priv->usb_20_clk);
-		clk_disable(priv->usb_30_clk);
+		clk_disable_unprepare(priv->usb_20_clk);
+		clk_disable_unprepare(priv->usb_30_clk);
 	}
 
 	return 0;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 03/13] phy: usb: Put USB phys into IDDQ on suspend to save power in S2 mode

[Al Cooper]

Currently the Phy driver will put the USB phys into the max
power saving mode (IDDQ) when there is no corresponding XHCI, EHCI
or OHCI client (through rmmod, unbind or if the driver is not
builtin). This change will also put the Phys into IDDQ mode
on suspend so that S2 will get the additional power savings.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb-init.c |  2 --
 drivers/phy/broadcom/phy-brcm-usb.c      | 11 +++++++++--
 2 files changed, 9 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index bd473d12ab28..ac7f7995c11f 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -1002,8 +1002,6 @@ void brcm_usb_uninit_common(struct brcm_usb_init_params *params)
 
 void brcm_usb_uninit_eohci(struct brcm_usb_init_params *params)
 {
-	if (USB_CTRL_MASK_FAMILY(params, USB_PM, USB20_HC_RESETB))
-		USB_CTRL_UNSET_FAMILY(params, USB_PM, USB20_HC_RESETB);
 }
 
 void brcm_usb_uninit_xhci(struct brcm_usb_init_params *params)
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 217e3702ef4e..634afc803778 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -381,8 +381,15 @@ static int brcm_usb_phy_suspend(struct device *dev)
 	struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
 
 	if (priv->init_count) {
-		clk_disable_unprepare(priv->usb_20_clk);
-		clk_disable_unprepare(priv->usb_30_clk);
+		if (priv->phys[BRCM_USB_PHY_3_0].inited)
+			brcm_usb_uninit_xhci(&priv->ini);
+		if (priv->phys[BRCM_USB_PHY_2_0].inited)
+			brcm_usb_uninit_eohci(&priv->ini);
+		brcm_usb_uninit_common(&priv->ini);
+		if (priv->phys[BRCM_USB_PHY_3_0].inited)
+			clk_disable_unprepare(priv->usb_30_clk);
+		if (priv->phys[BRCM_USB_PHY_2_0].inited)
+			clk_disable_unprepare(priv->usb_20_clk);
 	}
 	return 0;
 }
-- 
2.17.1

[PATCH v3 03/13] phy: usb: Put USB phys into IDDQ on suspend to save power in S2 mode

[Al Cooper]

Currently the Phy driver will put the USB phys into the max
power saving mode (IDDQ) when there is no corresponding XHCI, EHCI
or OHCI client (through rmmod, unbind or if the driver is not
builtin). This change will also put the Phys into IDDQ mode
on suspend so that S2 will get the additional power savings.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb-init.c |  2 --
 drivers/phy/broadcom/phy-brcm-usb.c      | 11 +++++++++--
 2 files changed, 9 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index bd473d12ab28..ac7f7995c11f 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -1002,8 +1002,6 @@ void brcm_usb_uninit_common(struct brcm_usb_init_params *params)
 
 void brcm_usb_uninit_eohci(struct brcm_usb_init_params *params)
 {
-	if (USB_CTRL_MASK_FAMILY(params, USB_PM, USB20_HC_RESETB))
-		USB_CTRL_UNSET_FAMILY(params, USB_PM, USB20_HC_RESETB);
 }
 
 void brcm_usb_uninit_xhci(struct brcm_usb_init_params *params)
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 217e3702ef4e..634afc803778 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -381,8 +381,15 @@ static int brcm_usb_phy_suspend(struct device *dev)
 	struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
 
 	if (priv->init_count) {
-		clk_disable_unprepare(priv->usb_20_clk);
-		clk_disable_unprepare(priv->usb_30_clk);
+		if (priv->phys[BRCM_USB_PHY_3_0].inited)
+			brcm_usb_uninit_xhci(&priv->ini);
+		if (priv->phys[BRCM_USB_PHY_2_0].inited)
+			brcm_usb_uninit_eohci(&priv->ini);
+		brcm_usb_uninit_common(&priv->ini);
+		if (priv->phys[BRCM_USB_PHY_3_0].inited)
+			clk_disable_unprepare(priv->usb_30_clk);
+		if (priv->phys[BRCM_USB_PHY_2_0].inited)
+			clk_disable_unprepare(priv->usb_20_clk);
 	}
 	return 0;
 }
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 04/13] phy: usb: Add "wake on" functionality

[Al Cooper]

Add the ability to handle USB wake events from USB devices when
in S2 mode. Typically there is some additional configuration
needed to tell the USB device to generate the wake event when
suspended but this varies with the different USB device classes.
For example, on USB Ethernet dongles, ethtool should be used to
enable the magic packet wake functionality in the dongle.
NOTE:  This requires that the "power/wakeup" sysfs entry for
the USB device generating the wakeup be set to "enabled".

This functionality requires a special hardware sideband path that
will trigger the AON_PM_L2 interrupt needed to wake the system from
S2 even though the USB host controllers are in IDDQ (low power state)
and most USB related clocks are shut off. For the sideband signaling
to work we need to leave the usbx_freerun clock running, but this
clock consumes very little power by design. There's a bug in the
XHCI wake hardware so only EHCI/OHCI wake is currently supported.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb-init.c | 17 +++++++++
 drivers/phy/broadcom/phy-brcm-usb-init.h |  1 +
 drivers/phy/broadcom/phy-brcm-usb.c      | 48 ++++++++++++++++++++++--
 3 files changed, 63 insertions(+), 3 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index ac7f7995c11f..58882c10396a 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -58,6 +58,8 @@
 #define   USB_CTRL_USB_PM_SOFT_RESET_MASK		0x40000000 /* option */
 #define   USB_CTRL_USB_PM_USB20_HC_RESETB_MASK		0x30000000 /* option */
 #define   USB_CTRL_USB_PM_USB20_HC_RESETB_VAR_MASK	0x00300000 /* option */
+#define   USB_CTRL_USB_PM_RMTWKUP_EN_MASK		0x00000001
+#define USB_CTRL_USB_PM_STATUS		0x38
 #define USB_CTRL_USB30_CTL1		0x60
 #define   USB_CTRL_USB30_CTL1_PHY3_PLL_SEQ_START_MASK	0x00000010
 #define   USB_CTRL_USB30_CTL1_PHY3_RESETB_MASK		0x00010000
@@ -855,6 +857,10 @@ void brcm_usb_init_common(struct brcm_usb_init_params *params)
 	u32 reg;
 	void __iomem *ctrl = params->ctrl_regs;
 
+	/* Clear any pending wake conditions */
+	reg = brcmusb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
+	brcmusb_writel(reg, USB_CTRL_REG(ctrl, USB_PM_STATUS));
+
 	/* Take USB out of power down */
 	if (USB_CTRL_MASK_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN)) {
 		USB_CTRL_UNSET_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN);
@@ -1010,6 +1016,17 @@ void brcm_usb_uninit_xhci(struct brcm_usb_init_params *params)
 	USB_CTRL_SET(params->ctrl_regs, USB30_PCTL, PHY3_IDDQ_OVERRIDE);
 }
 
+void brcm_usb_wake_enable(struct brcm_usb_init_params *params,
+			  int enable)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+
+	if (enable)
+		USB_CTRL_SET(ctrl, USB_PM, RMTWKUP_EN);
+	else
+		USB_CTRL_UNSET(ctrl, USB_PM, RMTWKUP_EN);
+}
+
 void brcm_usb_set_family_map(struct brcm_usb_init_params *params)
 {
 	int fam;
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index f4f4f6d5d258..f473e0c51f0b 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -38,5 +38,6 @@ void brcm_usb_init_xhci(struct brcm_usb_init_params *ini);
 void brcm_usb_uninit_common(struct brcm_usb_init_params *ini);
 void brcm_usb_uninit_eohci(struct brcm_usb_init_params *ini);
 void brcm_usb_uninit_xhci(struct brcm_usb_init_params *ini);
+void brcm_usb_wake_enable(struct brcm_usb_init_params *params, int enable);
 
 #endif /* _USB_BRCM_COMMON_INIT_H */
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 634afc803778..cca04d60f2d2 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -57,11 +57,22 @@ struct brcm_usb_phy_data {
 	bool			has_xhci;
 	struct clk		*usb_20_clk;
 	struct clk		*usb_30_clk;
+	struct clk		*suspend_clk;
 	struct mutex		mutex;	/* serialize phy init */
 	int			init_count;
+	int			wake_irq;
 	struct brcm_usb_phy	phys[BRCM_USB_PHY_ID_MAX];
 };
 
+static irqreturn_t brcm_usb_phy_wake_isr(int irq, void *dev_id)
+{
+	struct phy *gphy = dev_id;
+
+	pm_wakeup_event(&gphy->dev, 0);
+
+	return IRQ_HANDLED;
+}
+
 static int brcm_usb_phy_init(struct phy *gphy)
 {
 	struct brcm_usb_phy *phy = phy_get_drvdata(gphy);
@@ -76,6 +87,7 @@ static int brcm_usb_phy_init(struct phy *gphy)
 	if (priv->init_count++ == 0) {
 		clk_prepare_enable(priv->usb_20_clk);
 		clk_prepare_enable(priv->usb_30_clk);
+		clk_prepare_enable(priv->suspend_clk);
 		brcm_usb_init_common(&priv->ini);
 	}
 	mutex_unlock(&priv->mutex);
@@ -108,6 +120,7 @@ static int brcm_usb_phy_exit(struct phy *gphy)
 		brcm_usb_uninit_common(&priv->ini);
 		clk_disable_unprepare(priv->usb_20_clk);
 		clk_disable_unprepare(priv->usb_30_clk);
+		clk_disable_unprepare(priv->suspend_clk);
 	}
 	mutex_unlock(&priv->mutex);
 	phy->inited = false;
@@ -228,11 +241,12 @@ static const struct attribute_group brcm_usb_phy_group = {
 	.attrs = brcm_usb_phy_attrs,
 };
 
-static int brcm_usb_phy_dvr_init(struct device *dev,
+static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 				 struct brcm_usb_phy_data *priv,
 				 struct device_node *dn)
 {
-	struct phy *gphy;
+	struct device *dev = &pdev->dev;
+	struct phy *gphy = NULL;
 	int err;
 
 	priv->usb_20_clk = of_clk_get_by_name(dn, "sw_usb");
@@ -275,6 +289,28 @@ static int brcm_usb_phy_dvr_init(struct device *dev,
 		if (err)
 			return err;
 	}
+
+	priv->suspend_clk = clk_get(dev, "usb0_freerun");
+	if (IS_ERR(priv->suspend_clk)) {
+		dev_err(dev, "Suspend Clock not found in Device Tree\n");
+		priv->suspend_clk = NULL;
+	}
+
+	priv->wake_irq = platform_get_irq_byname(pdev, "wake");
+	if (priv->wake_irq < 0)
+		priv->wake_irq = platform_get_irq_byname(pdev, "wakeup");
+	if (priv->wake_irq >= 0) {
+		err = devm_request_irq(dev, priv->wake_irq,
+				       brcm_usb_phy_wake_isr, 0,
+				       dev_name(dev), gphy);
+		if (err < 0)
+			return err;
+		device_set_wakeup_capable(dev, 1);
+	} else {
+		dev_info(dev,
+			 "Wake interrupt missing, system wake not supported\n");
+	}
+
 	return 0;
 }
 
@@ -335,7 +371,7 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	if (of_property_read_bool(dn, "brcm,has-eohci"))
 		priv->has_eohci = true;
 
-	err = brcm_usb_phy_dvr_init(dev, priv, dn);
+	err = brcm_usb_phy_dvr_init(pdev, priv, dn);
 	if (err)
 		return err;
 
@@ -386,10 +422,13 @@ static int brcm_usb_phy_suspend(struct device *dev)
 		if (priv->phys[BRCM_USB_PHY_2_0].inited)
 			brcm_usb_uninit_eohci(&priv->ini);
 		brcm_usb_uninit_common(&priv->ini);
+		brcm_usb_wake_enable(&priv->ini, true);
 		if (priv->phys[BRCM_USB_PHY_3_0].inited)
 			clk_disable_unprepare(priv->usb_30_clk);
 		if (priv->phys[BRCM_USB_PHY_2_0].inited)
 			clk_disable_unprepare(priv->usb_20_clk);
+		if (priv->wake_irq >= 0)
+			enable_irq_wake(priv->wake_irq);
 	}
 	return 0;
 }
@@ -400,6 +439,7 @@ static int brcm_usb_phy_resume(struct device *dev)
 
 	clk_prepare_enable(priv->usb_20_clk);
 	clk_prepare_enable(priv->usb_30_clk);
+	brcm_usb_wake_enable(&priv->ini, false);
 	brcm_usb_init_ipp(&priv->ini);
 
 	/*
@@ -407,6 +447,8 @@ static int brcm_usb_phy_resume(struct device *dev)
 	 * Uninitialize anything that wasn't previously initialized.
 	 */
 	if (priv->init_count) {
+		if (priv->wake_irq >= 0)
+			disable_irq_wake(priv->wake_irq);
 		brcm_usb_init_common(&priv->ini);
 		if (priv->phys[BRCM_USB_PHY_2_0].inited) {
 			brcm_usb_init_eohci(&priv->ini);
-- 
2.17.1

[PATCH v3 04/13] phy: usb: Add "wake on" functionality

[Al Cooper]

Add the ability to handle USB wake events from USB devices when
in S2 mode. Typically there is some additional configuration
needed to tell the USB device to generate the wake event when
suspended but this varies with the different USB device classes.
For example, on USB Ethernet dongles, ethtool should be used to
enable the magic packet wake functionality in the dongle.
NOTE:  This requires that the "power/wakeup" sysfs entry for
the USB device generating the wakeup be set to "enabled".

This functionality requires a special hardware sideband path that
will trigger the AON_PM_L2 interrupt needed to wake the system from
S2 even though the USB host controllers are in IDDQ (low power state)
and most USB related clocks are shut off. For the sideband signaling
to work we need to leave the usbx_freerun clock running, but this
clock consumes very little power by design. There's a bug in the
XHCI wake hardware so only EHCI/OHCI wake is currently supported.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb-init.c | 17 +++++++++
 drivers/phy/broadcom/phy-brcm-usb-init.h |  1 +
 drivers/phy/broadcom/phy-brcm-usb.c      | 48 ++++++++++++++++++++++--
 3 files changed, 63 insertions(+), 3 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index ac7f7995c11f..58882c10396a 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -58,6 +58,8 @@
 #define   USB_CTRL_USB_PM_SOFT_RESET_MASK		0x40000000 /* option */
 #define   USB_CTRL_USB_PM_USB20_HC_RESETB_MASK		0x30000000 /* option */
 #define   USB_CTRL_USB_PM_USB20_HC_RESETB_VAR_MASK	0x00300000 /* option */
+#define   USB_CTRL_USB_PM_RMTWKUP_EN_MASK		0x00000001
+#define USB_CTRL_USB_PM_STATUS		0x38
 #define USB_CTRL_USB30_CTL1		0x60
 #define   USB_CTRL_USB30_CTL1_PHY3_PLL_SEQ_START_MASK	0x00000010
 #define   USB_CTRL_USB30_CTL1_PHY3_RESETB_MASK		0x00010000
@@ -855,6 +857,10 @@ void brcm_usb_init_common(struct brcm_usb_init_params *params)
 	u32 reg;
 	void __iomem *ctrl = params->ctrl_regs;
 
+	/* Clear any pending wake conditions */
+	reg = brcmusb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
+	brcmusb_writel(reg, USB_CTRL_REG(ctrl, USB_PM_STATUS));
+
 	/* Take USB out of power down */
 	if (USB_CTRL_MASK_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN)) {
 		USB_CTRL_UNSET_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN);
@@ -1010,6 +1016,17 @@ void brcm_usb_uninit_xhci(struct brcm_usb_init_params *params)
 	USB_CTRL_SET(params->ctrl_regs, USB30_PCTL, PHY3_IDDQ_OVERRIDE);
 }
 
+void brcm_usb_wake_enable(struct brcm_usb_init_params *params,
+			  int enable)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+
+	if (enable)
+		USB_CTRL_SET(ctrl, USB_PM, RMTWKUP_EN);
+	else
+		USB_CTRL_UNSET(ctrl, USB_PM, RMTWKUP_EN);
+}
+
 void brcm_usb_set_family_map(struct brcm_usb_init_params *params)
 {
 	int fam;
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index f4f4f6d5d258..f473e0c51f0b 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -38,5 +38,6 @@ void brcm_usb_init_xhci(struct brcm_usb_init_params *ini);
 void brcm_usb_uninit_common(struct brcm_usb_init_params *ini);
 void brcm_usb_uninit_eohci(struct brcm_usb_init_params *ini);
 void brcm_usb_uninit_xhci(struct brcm_usb_init_params *ini);
+void brcm_usb_wake_enable(struct brcm_usb_init_params *params, int enable);
 
 #endif /* _USB_BRCM_COMMON_INIT_H */
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 634afc803778..cca04d60f2d2 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -57,11 +57,22 @@ struct brcm_usb_phy_data {
 	bool			has_xhci;
 	struct clk		*usb_20_clk;
 	struct clk		*usb_30_clk;
+	struct clk		*suspend_clk;
 	struct mutex		mutex;	/* serialize phy init */
 	int			init_count;
+	int			wake_irq;
 	struct brcm_usb_phy	phys[BRCM_USB_PHY_ID_MAX];
 };
 
+static irqreturn_t brcm_usb_phy_wake_isr(int irq, void *dev_id)
+{
+	struct phy *gphy = dev_id;
+
+	pm_wakeup_event(&gphy->dev, 0);
+
+	return IRQ_HANDLED;
+}
+
 static int brcm_usb_phy_init(struct phy *gphy)
 {
 	struct brcm_usb_phy *phy = phy_get_drvdata(gphy);
@@ -76,6 +87,7 @@ static int brcm_usb_phy_init(struct phy *gphy)
 	if (priv->init_count++ == 0) {
 		clk_prepare_enable(priv->usb_20_clk);
 		clk_prepare_enable(priv->usb_30_clk);
+		clk_prepare_enable(priv->suspend_clk);
 		brcm_usb_init_common(&priv->ini);
 	}
 	mutex_unlock(&priv->mutex);
@@ -108,6 +120,7 @@ static int brcm_usb_phy_exit(struct phy *gphy)
 		brcm_usb_uninit_common(&priv->ini);
 		clk_disable_unprepare(priv->usb_20_clk);
 		clk_disable_unprepare(priv->usb_30_clk);
+		clk_disable_unprepare(priv->suspend_clk);
 	}
 	mutex_unlock(&priv->mutex);
 	phy->inited = false;
@@ -228,11 +241,12 @@ static const struct attribute_group brcm_usb_phy_group = {
 	.attrs = brcm_usb_phy_attrs,
 };
 
-static int brcm_usb_phy_dvr_init(struct device *dev,
+static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 				 struct brcm_usb_phy_data *priv,
 				 struct device_node *dn)
 {
-	struct phy *gphy;
+	struct device *dev = &pdev->dev;
+	struct phy *gphy = NULL;
 	int err;
 
 	priv->usb_20_clk = of_clk_get_by_name(dn, "sw_usb");
@@ -275,6 +289,28 @@ static int brcm_usb_phy_dvr_init(struct device *dev,
 		if (err)
 			return err;
 	}
+
+	priv->suspend_clk = clk_get(dev, "usb0_freerun");
+	if (IS_ERR(priv->suspend_clk)) {
+		dev_err(dev, "Suspend Clock not found in Device Tree\n");
+		priv->suspend_clk = NULL;
+	}
+
+	priv->wake_irq = platform_get_irq_byname(pdev, "wake");
+	if (priv->wake_irq < 0)
+		priv->wake_irq = platform_get_irq_byname(pdev, "wakeup");
+	if (priv->wake_irq >= 0) {
+		err = devm_request_irq(dev, priv->wake_irq,
+				       brcm_usb_phy_wake_isr, 0,
+				       dev_name(dev), gphy);
+		if (err < 0)
+			return err;
+		device_set_wakeup_capable(dev, 1);
+	} else {
+		dev_info(dev,
+			 "Wake interrupt missing, system wake not supported\n");
+	}
+
 	return 0;
 }
 
@@ -335,7 +371,7 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	if (of_property_read_bool(dn, "brcm,has-eohci"))
 		priv->has_eohci = true;
 
-	err = brcm_usb_phy_dvr_init(dev, priv, dn);
+	err = brcm_usb_phy_dvr_init(pdev, priv, dn);
 	if (err)
 		return err;
 
@@ -386,10 +422,13 @@ static int brcm_usb_phy_suspend(struct device *dev)
 		if (priv->phys[BRCM_USB_PHY_2_0].inited)
 			brcm_usb_uninit_eohci(&priv->ini);
 		brcm_usb_uninit_common(&priv->ini);
+		brcm_usb_wake_enable(&priv->ini, true);
 		if (priv->phys[BRCM_USB_PHY_3_0].inited)
 			clk_disable_unprepare(priv->usb_30_clk);
 		if (priv->phys[BRCM_USB_PHY_2_0].inited)
 			clk_disable_unprepare(priv->usb_20_clk);
+		if (priv->wake_irq >= 0)
+			enable_irq_wake(priv->wake_irq);
 	}
 	return 0;
 }
@@ -400,6 +439,7 @@ static int brcm_usb_phy_resume(struct device *dev)
 
 	clk_prepare_enable(priv->usb_20_clk);
 	clk_prepare_enable(priv->usb_30_clk);
+	brcm_usb_wake_enable(&priv->ini, false);
 	brcm_usb_init_ipp(&priv->ini);
 
 	/*
@@ -407,6 +447,8 @@ static int brcm_usb_phy_resume(struct device *dev)
 	 * Uninitialize anything that wasn't previously initialized.
 	 */
 	if (priv->init_count) {
+		if (priv->wake_irq >= 0)
+			disable_irq_wake(priv->wake_irq);
 		brcm_usb_init_common(&priv->ini);
 		if (priv->phys[BRCM_USB_PHY_2_0].inited) {
 			brcm_usb_init_eohci(&priv->ini);
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 05/13] phy: usb: Restructure in preparation for adding 7216 USB support

[Al Cooper]

The driver is being restructured in preparation for adding support
for the new Synopsis USB conroller on the 7216. Since all the bugs
and work-arounds in previous STB chips are supposed to be fixed,
most of the code in phy-brcm-usb-init.c is not needed. Instead of
adding more complexity to the already complicated phy-brcm-usb-init.c
module, the driver will be restructured to use a vector table to
dispatch into different C modules for the different controllers.

There was also some general cleanup done including some ipp setup
code that was incorrect.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb-init.c | 191 ++++++++++-------------
 drivers/phy/broadcom/phy-brcm-usb-init.h | 140 +++++++++++++++--
 drivers/phy/broadcom/phy-brcm-usb.c      |   6 +-
 3 files changed, 214 insertions(+), 123 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index 58882c10396a..80d6f54d276e 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -129,10 +129,6 @@ enum {
 	USB_CTRL_SELECTOR_COUNT,
 };
 
-#define USB_CTRL_REG(base, reg)	((void __iomem *)base + USB_CTRL_##reg)
-#define USB_XHCI_EC_REG(base, reg) ((void __iomem *)base + USB_XHCI_EC_##reg)
-#define USB_CTRL_MASK(reg, field) \
-	USB_CTRL_##reg##_##field##_MASK
 #define USB_CTRL_MASK_FAMILY(params, reg, field)			\
 	(params->usb_reg_bits_map[USB_CTRL_##reg##_##field##_SELECTOR])
 
@@ -143,13 +139,6 @@ enum {
 	usb_ctrl_unset_family(params, USB_CTRL_##reg,	\
 		USB_CTRL_##reg##_##field##_SELECTOR)
 
-#define USB_CTRL_SET(base, reg, field)	\
-	usb_ctrl_set(USB_CTRL_REG(base, reg),		\
-		     USB_CTRL_##reg##_##field##_MASK)
-#define USB_CTRL_UNSET(base, reg, field)	\
-	usb_ctrl_unset(USB_CTRL_REG(base, reg),		\
-		       USB_CTRL_##reg##_##field##_MASK)
-
 #define MDIO_USB2	0
 #define MDIO_USB3	BIT(31)
 
@@ -405,26 +394,14 @@ usb_reg_bits_map_table[BRCM_FAMILY_COUNT][USB_CTRL_SELECTOR_COUNT] = {
 	},
 };
 
-static inline u32 brcmusb_readl(void __iomem *addr)
-{
-	return readl(addr);
-}
-
-static inline void brcmusb_writel(u32 val, void __iomem *addr)
-{
-	writel(val, addr);
-}
-
 static inline
 void usb_ctrl_unset_family(struct brcm_usb_init_params *params,
 			   u32 reg_offset, u32 field)
 {
 	u32 mask;
-	void __iomem *reg;
 
 	mask = params->usb_reg_bits_map[field];
-	reg = params->ctrl_regs + reg_offset;
-	brcmusb_writel(brcmusb_readl(reg) & ~mask, reg);
+	brcm_usb_ctrl_unset(params->ctrl_regs + reg_offset, mask);
 };
 
 static inline
@@ -432,45 +409,27 @@ void usb_ctrl_set_family(struct brcm_usb_init_params *params,
 			 u32 reg_offset, u32 field)
 {
 	u32 mask;
-	void __iomem *reg;
 
 	mask = params->usb_reg_bits_map[field];
-	reg = params->ctrl_regs + reg_offset;
-	brcmusb_writel(brcmusb_readl(reg) | mask, reg);
+	brcm_usb_ctrl_set(params->ctrl_regs + reg_offset, mask);
 };
 
-static inline void usb_ctrl_set(void __iomem *reg, u32 field)
-{
-	u32 value;
-
-	value = brcmusb_readl(reg);
-	brcmusb_writel(value | field, reg);
-}
-
-static inline void usb_ctrl_unset(void __iomem *reg, u32 field)
-{
-	u32 value;
-
-	value = brcmusb_readl(reg);
-	brcmusb_writel(value & ~field, reg);
-}
-
 static u32 brcmusb_usb_mdio_read(void __iomem *ctrl_base, u32 reg, int mode)
 {
 	u32 data;
 
 	data = (reg << 16) | mode;
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	data |= (1 << 24);
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	data &= ~(1 << 24);
 	/* wait for the 60MHz parallel to serial shifter */
 	usleep_range(10, 20);
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	/* wait for the 60MHz parallel to serial shifter */
 	usleep_range(10, 20);
 
-	return brcmusb_readl(USB_CTRL_REG(ctrl_base, MDIO2)) & 0xffff;
+	return brcm_usb_readl(USB_CTRL_REG(ctrl_base, MDIO2)) & 0xffff;
 }
 
 static void brcmusb_usb_mdio_write(void __iomem *ctrl_base, u32 reg,
@@ -479,14 +438,14 @@ static void brcmusb_usb_mdio_write(void __iomem *ctrl_base, u32 reg,
 	u32 data;
 
 	data = (reg << 16) | val | mode;
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	data |= (1 << 25);
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	data &= ~(1 << 25);
 
 	/* wait for the 60MHz parallel to serial shifter */
 	usleep_range(10, 20);
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	/* wait for the 60MHz parallel to serial shifter */
 	usleep_range(10, 20);
 }
@@ -713,12 +672,12 @@ static void brcmusb_usb3_otp_fix(struct brcm_usb_init_params *params)
 
 	if (params->family_id != 0x74371000 || !xhci_ec_base)
 		return;
-	brcmusb_writel(0xa20c, USB_XHCI_EC_REG(xhci_ec_base, IRAADR));
-	val = brcmusb_readl(USB_XHCI_EC_REG(xhci_ec_base, IRADAT));
+	brcm_usb_writel(0xa20c, USB_XHCI_EC_REG(xhci_ec_base, IRAADR));
+	val = brcm_usb_readl(USB_XHCI_EC_REG(xhci_ec_base, IRADAT));
 
 	/* set cfg_pick_ss_lock */
 	val |= (1 << 27);
-	brcmusb_writel(val, USB_XHCI_EC_REG(xhci_ec_base, IRADAT));
+	brcm_usb_writel(val, USB_XHCI_EC_REG(xhci_ec_base, IRADAT));
 
 	/* Reset USB 3.0 PHY for workaround to take effect */
 	USB_CTRL_UNSET(params->ctrl_regs, USB30_CTL1, PHY3_RESETB);
@@ -751,7 +710,7 @@ static void brcmusb_xhci_soft_reset(struct brcm_usb_init_params *params,
  *   - default chip/rev.
  * NOTE: The minor rev is always ignored.
  */
-static enum brcm_family_type brcmusb_get_family_type(
+static enum brcm_family_type get_family_type(
 	struct brcm_usb_init_params *params)
 {
 	int last_type = -1;
@@ -779,7 +738,7 @@ static enum brcm_family_type brcmusb_get_family_type(
 	return last_type;
 }
 
-void brcm_usb_init_ipp(struct brcm_usb_init_params *params)
+static void usb_init_ipp(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->ctrl_regs;
 	u32 reg;
@@ -795,7 +754,7 @@ void brcm_usb_init_ipp(struct brcm_usb_init_params *params)
 			USB_CTRL_SET_FAMILY(params, USB30_CTL1, USB3_IPP);
 	}
 
-	reg = brcmusb_readl(USB_CTRL_REG(ctrl, SETUP));
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
 	orig_reg = reg;
 	if (USB_CTRL_MASK_FAMILY(params, SETUP, STRAP_CC_DRD_MODE_ENABLE_SEL))
 		/* Never use the strap, it's going away. */
@@ -803,8 +762,8 @@ void brcm_usb_init_ipp(struct brcm_usb_init_params *params)
 					      SETUP,
 					      STRAP_CC_DRD_MODE_ENABLE_SEL));
 	if (USB_CTRL_MASK_FAMILY(params, SETUP, STRAP_IPP_SEL))
+		/* override ipp strap pin (if it exits) */
 		if (params->ipp != 2)
-			/* override ipp strap pin (if it exits) */
 			reg &= ~(USB_CTRL_MASK_FAMILY(params, SETUP,
 						      STRAP_IPP_SEL));
 
@@ -812,54 +771,26 @@ void brcm_usb_init_ipp(struct brcm_usb_init_params *params)
 	reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
 	if (params->ioc)
 		reg |= USB_CTRL_MASK(SETUP, IOC);
-	if (params->ipp == 1 && ((reg & USB_CTRL_MASK(SETUP, IPP)) == 0))
+	if (params->ipp == 1)
 		reg |= USB_CTRL_MASK(SETUP, IPP);
-	brcmusb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
 
 	/*
 	 * If we're changing IPP, make sure power is off long enough
 	 * to turn off any connected devices.
 	 */
-	if (reg != orig_reg)
+	if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
 		msleep(50);
 }
 
-int brcm_usb_init_get_dual_select(struct brcm_usb_init_params *params)
-{
-	void __iomem *ctrl = params->ctrl_regs;
-	u32 reg = 0;
-
-	if (USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1, PORT_MODE)) {
-		reg = brcmusb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
-		reg &= USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1,
-					PORT_MODE);
-	}
-	return reg;
-}
-
-void brcm_usb_init_set_dual_select(struct brcm_usb_init_params *params,
-				   int mode)
-{
-	void __iomem *ctrl = params->ctrl_regs;
-	u32 reg;
-
-	if (USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1, PORT_MODE)) {
-		reg = brcmusb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
-		reg &= ~USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1,
-					PORT_MODE);
-		reg |= mode;
-		brcmusb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
-	}
-}
-
-void brcm_usb_init_common(struct brcm_usb_init_params *params)
+static void usb_init_common(struct brcm_usb_init_params *params)
 {
 	u32 reg;
 	void __iomem *ctrl = params->ctrl_regs;
 
 	/* Clear any pending wake conditions */
-	reg = brcmusb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
-	brcmusb_writel(reg, USB_CTRL_REG(ctrl, USB_PM_STATUS));
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_PM_STATUS));
 
 	/* Take USB out of power down */
 	if (USB_CTRL_MASK_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN)) {
@@ -885,7 +816,7 @@ void brcm_usb_init_common(struct brcm_usb_init_params *params)
 	/* Block auto PLL suspend by USB2 PHY (Sasi) */
 	USB_CTRL_SET(ctrl, PLL_CTL, PLL_SUSPEND_EN);
 
-	reg = brcmusb_readl(USB_CTRL_REG(ctrl, SETUP));
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
 	if (params->selected_family == BRCM_FAMILY_7364A0)
 		/* Suppress overcurrent indication from USB30 ports for A0 */
 		reg |= USB_CTRL_MASK_FAMILY(params, SETUP, OC3_DISABLE);
@@ -901,16 +832,16 @@ void brcm_usb_init_common(struct brcm_usb_init_params *params)
 		reg |= USB_CTRL_MASK_FAMILY(params, SETUP, SCB1_EN);
 	if (USB_CTRL_MASK_FAMILY(params, SETUP, SCB2_EN))
 		reg |= USB_CTRL_MASK_FAMILY(params, SETUP, SCB2_EN);
-	brcmusb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
 
 	brcmusb_memc_fix(params);
 
 	if (USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1, PORT_MODE)) {
-		reg = brcmusb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
 		reg &= ~USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1,
 					PORT_MODE);
 		reg |= params->mode;
-		brcmusb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+		brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
 	}
 	if (USB_CTRL_MASK_FAMILY(params, USB_PM, BDC_SOFT_RESETB)) {
 		switch (params->mode) {
@@ -932,7 +863,7 @@ void brcm_usb_init_common(struct brcm_usb_init_params *params)
 	}
 }
 
-void brcm_usb_init_eohci(struct brcm_usb_init_params *params)
+static void usb_init_eohci(struct brcm_usb_init_params *params)
 {
 	u32 reg;
 	void __iomem *ctrl = params->ctrl_regs;
@@ -948,10 +879,10 @@ void brcm_usb_init_eohci(struct brcm_usb_init_params *params)
 		USB_CTRL_SET(ctrl, EBRIDGE, ESTOP_SCB_REQ);
 
 	/* Setup the endian bits */
-	reg = brcmusb_readl(USB_CTRL_REG(ctrl, SETUP));
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
 	reg &= ~USB_CTRL_SETUP_ENDIAN_BITS;
 	reg |= USB_CTRL_MASK_FAMILY(params, SETUP, ENDIAN);
-	brcmusb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
 
 	if (params->selected_family == BRCM_FAMILY_7271A0)
 		/* Enable LS keep alive fix for certain keyboards */
@@ -962,14 +893,14 @@ void brcm_usb_init_eohci(struct brcm_usb_init_params *params)
 		 * Make the burst size 512 bytes to fix a hardware bug
 		 * on the 7255a0. See HW7255-24.
 		 */
-		reg = brcmusb_readl(USB_CTRL_REG(ctrl, EBRIDGE));
+		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, EBRIDGE));
 		reg &= ~USB_CTRL_MASK(EBRIDGE, EBR_SCB_SIZE);
 		reg |= 0x800;
-		brcmusb_writel(reg, USB_CTRL_REG(ctrl, EBRIDGE));
+		brcm_usb_writel(reg, USB_CTRL_REG(ctrl, EBRIDGE));
 	}
 }
 
-void brcm_usb_init_xhci(struct brcm_usb_init_params *params)
+static void usb_init_xhci(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->ctrl_regs;
 
@@ -997,7 +928,7 @@ void brcm_usb_init_xhci(struct brcm_usb_init_params *params)
 	brcmusb_usb3_otp_fix(params);
 }
 
-void brcm_usb_uninit_common(struct brcm_usb_init_params *params)
+static void usb_uninit_common(struct brcm_usb_init_params *params)
 {
 	if (USB_CTRL_MASK_FAMILY(params, USB_PM, USB_PWRDN))
 		USB_CTRL_SET_FAMILY(params, USB_PM, USB_PWRDN);
@@ -1006,17 +937,47 @@ void brcm_usb_uninit_common(struct brcm_usb_init_params *params)
 		USB_CTRL_SET_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN);
 }
 
-void brcm_usb_uninit_eohci(struct brcm_usb_init_params *params)
+static void usb_uninit_eohci(struct brcm_usb_init_params *params)
 {
 }
 
-void brcm_usb_uninit_xhci(struct brcm_usb_init_params *params)
+static void usb_uninit_xhci(struct brcm_usb_init_params *params)
 {
 	brcmusb_xhci_soft_reset(params, 1);
 	USB_CTRL_SET(params->ctrl_regs, USB30_PCTL, PHY3_IDDQ_OVERRIDE);
 }
 
-void brcm_usb_wake_enable(struct brcm_usb_init_params *params,
+static int usb_get_dual_select(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+	u32 reg = 0;
+
+	pr_debug("%s\n", __func__);
+	if (USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1, PORT_MODE)) {
+		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+		reg &= USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1,
+					PORT_MODE);
+	}
+	return reg;
+}
+
+static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+	u32 reg;
+
+	pr_debug("%s\n", __func__);
+
+	if (USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1, PORT_MODE)) {
+		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+		reg &= ~USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1,
+					PORT_MODE);
+		reg |= mode;
+		brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+	}
+}
+
+static void usb_wake_enable(struct brcm_usb_init_params *params,
 			  int enable)
 {
 	void __iomem *ctrl = params->ctrl_regs;
@@ -1027,13 +988,29 @@ void brcm_usb_wake_enable(struct brcm_usb_init_params *params,
 		USB_CTRL_UNSET(ctrl, USB_PM, RMTWKUP_EN);
 }
 
-void brcm_usb_set_family_map(struct brcm_usb_init_params *params)
+static const struct brcm_usb_init_ops bcm7445_ops = {
+	.init_ipp = usb_init_ipp,
+	.init_common = usb_init_common,
+	.init_eohci = usb_init_eohci,
+	.init_xhci = usb_init_xhci,
+	.uninit_common = usb_uninit_common,
+	.uninit_eohci = usb_uninit_eohci,
+	.uninit_xhci = usb_uninit_xhci,
+	.get_dual_select = usb_get_dual_select,
+	.set_dual_select = usb_set_dual_select,
+	.wake_enable = usb_wake_enable,
+};
+
+void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params)
 {
 	int fam;
 
-	fam = brcmusb_get_family_type(params);
+	pr_debug("%s\n", __func__);
+
+	fam = get_family_type(params);
 	params->selected_family = fam;
 	params->usb_reg_bits_map =
 		&usb_reg_bits_map_table[fam][0];
 	params->family_name = family_names[fam];
+	params->ops = &bcm7445_ops;
 }
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index f473e0c51f0b..7701872d1136 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -13,6 +13,33 @@
 
 struct  brcm_usb_init_params;
 
+#define USB_CTRL_REG(base, reg)	((void __iomem *)base + USB_CTRL_##reg)
+#define USB_XHCI_EC_REG(base, reg) ((void __iomem *)base + USB_XHCI_EC_##reg)
+#define USB_CTRL_MASK(reg, field) \
+	USB_CTRL_##reg##_##field##_MASK
+#define USB_CTRL_SET(base, reg, field)	\
+	brcm_usb_ctrl_set(USB_CTRL_REG(base, reg),	\
+			  USB_CTRL_##reg##_##field##_MASK)
+#define USB_CTRL_UNSET(base, reg, field)	\
+	brcm_usb_ctrl_unset(USB_CTRL_REG(base, reg),		\
+			    USB_CTRL_##reg##_##field##_MASK)
+
+struct  brcm_usb_init_params;
+
+struct brcm_usb_init_ops {
+	void (*init_ipp)(struct brcm_usb_init_params *params);
+	void (*init_common)(struct brcm_usb_init_params *params);
+	void (*init_eohci)(struct brcm_usb_init_params *params);
+	void (*init_xhci)(struct brcm_usb_init_params *params);
+	void (*uninit_common)(struct brcm_usb_init_params *params);
+	void (*uninit_eohci)(struct brcm_usb_init_params *params);
+	void (*uninit_xhci)(struct brcm_usb_init_params *params);
+	int  (*get_dual_select)(struct brcm_usb_init_params *params);
+	void (*set_dual_select)(struct brcm_usb_init_params *params, int mode);
+	void (*wake_enable)(struct brcm_usb_init_params *params,
+			    int enable);
+};
+
 struct  brcm_usb_init_params {
 	void __iomem *ctrl_regs;
 	void __iomem *xhci_ec_regs;
@@ -24,20 +51,107 @@ struct  brcm_usb_init_params {
 	int selected_family;
 	const char *family_name;
 	const u32 *usb_reg_bits_map;
+	const struct brcm_usb_init_ops *ops;
 };
 
-void brcm_usb_set_family_map(struct brcm_usb_init_params *params);
-int brcm_usb_init_get_dual_select(struct brcm_usb_init_params *params);
-void brcm_usb_init_set_dual_select(struct brcm_usb_init_params *params,
-				   int mode);
-
-void brcm_usb_init_ipp(struct brcm_usb_init_params *ini);
-void brcm_usb_init_common(struct brcm_usb_init_params *ini);
-void brcm_usb_init_eohci(struct brcm_usb_init_params *ini);
-void brcm_usb_init_xhci(struct brcm_usb_init_params *ini);
-void brcm_usb_uninit_common(struct brcm_usb_init_params *ini);
-void brcm_usb_uninit_eohci(struct brcm_usb_init_params *ini);
-void brcm_usb_uninit_xhci(struct brcm_usb_init_params *ini);
-void brcm_usb_wake_enable(struct brcm_usb_init_params *params, int enable);
+void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
+
+static inline u32 brcm_usb_readl(void __iomem *addr)
+{
+	/*
+	 * MIPS endianness is configured by boot strap, which also reverses all
+	 * bus endianness (i.e., big-endian CPU + big endian bus ==> native
+	 * endian I/O).
+	 *
+	 * Other architectures (e.g., ARM) either do not support big endian, or
+	 * else leave I/O in little endian mode.
+	 */
+	if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(__BIG_ENDIAN))
+		return __raw_readl(addr);
+	else
+		return readl_relaxed(addr);
+}
+
+static inline void brcm_usb_writel(u32 val, void __iomem *addr)
+{
+	/* See brcmnand_readl() comments */
+	if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(__BIG_ENDIAN))
+		__raw_writel(val, addr);
+	else
+		writel_relaxed(val, addr);
+}
+
+static inline void brcm_usb_ctrl_unset(void __iomem *reg, u32 mask)
+{
+	brcm_usb_writel(brcm_usb_readl(reg) & ~(mask), reg);
+};
+
+static inline void brcm_usb_ctrl_set(void __iomem *reg, u32 mask)
+{
+	brcm_usb_writel(brcm_usb_readl(reg) | (mask), reg);
+};
+
+static inline void brcm_usb_init_ipp(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->init_ipp)
+		ini->ops->init_ipp(ini);
+}
+
+static inline void brcm_usb_init_common(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->init_common)
+		ini->ops->init_common(ini);
+}
+
+static inline void brcm_usb_init_eohci(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->init_eohci)
+		ini->ops->init_eohci(ini);
+}
+
+static inline void brcm_usb_init_xhci(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->init_xhci)
+		ini->ops->init_xhci(ini);
+}
+
+static inline void brcm_usb_uninit_common(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->uninit_common)
+		ini->ops->uninit_common(ini);
+}
+
+static inline void brcm_usb_uninit_eohci(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->uninit_eohci)
+		ini->ops->uninit_eohci(ini);
+}
+
+static inline void brcm_usb_uninit_xhci(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->uninit_xhci)
+		ini->ops->uninit_xhci(ini);
+}
+
+static inline void brcm_usb_wake_enable(struct brcm_usb_init_params *ini,
+	int enable)
+{
+	if (ini->ops->wake_enable)
+		ini->ops->wake_enable(ini, enable);
+}
+
+static inline int brcm_usb_get_dual_select(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->get_dual_select)
+		return ini->ops->get_dual_select(ini);
+	return 0;
+}
+
+static inline void brcm_usb_set_dual_select(struct brcm_usb_init_params *ini,
+	int mode)
+{
+	if (ini->ops->set_dual_select)
+		ini->ops->set_dual_select(ini, mode);
+}
 
 #endif /* _USB_BRCM_COMMON_INIT_H */
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index cca04d60f2d2..9d93c5599511 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -207,7 +207,7 @@ static ssize_t dual_select_store(struct device *dev,
 	res = name_to_value(&brcm_dual_mode_to_name[0],
 			    ARRAY_SIZE(brcm_dual_mode_to_name), buf, &value);
 	if (!res) {
-		brcm_usb_init_set_dual_select(&priv->ini, value);
+		brcm_usb_set_dual_select(&priv->ini, value);
 		res = len;
 	}
 	mutex_unlock(&sysfs_lock);
@@ -222,7 +222,7 @@ static ssize_t dual_select_show(struct device *dev,
 	int value;
 
 	mutex_lock(&sysfs_lock);
-	value = brcm_usb_init_get_dual_select(&priv->ini);
+	value = brcm_usb_get_dual_select(&priv->ini);
 	mutex_unlock(&sysfs_lock);
 	return sprintf(buf, "%s\n",
 		value_to_name(&brcm_dual_mode_to_name[0],
@@ -331,7 +331,7 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 
 	priv->ini.family_id = brcmstb_get_family_id();
 	priv->ini.product_id = brcmstb_get_product_id();
-	brcm_usb_set_family_map(&priv->ini);
+	brcm_usb_dvr_init_7445(&priv->ini);
 	dev_dbg(dev, "Best mapping table is for %s\n",
 		priv->ini.family_name);
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-- 
2.17.1

[PATCH v3 05/13] phy: usb: Restructure in preparation for adding 7216 USB support

[Al Cooper]

The driver is being restructured in preparation for adding support
for the new Synopsis USB conroller on the 7216. Since all the bugs
and work-arounds in previous STB chips are supposed to be fixed,
most of the code in phy-brcm-usb-init.c is not needed. Instead of
adding more complexity to the already complicated phy-brcm-usb-init.c
module, the driver will be restructured to use a vector table to
dispatch into different C modules for the different controllers.

There was also some general cleanup done including some ipp setup
code that was incorrect.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb-init.c | 191 ++++++++++-------------
 drivers/phy/broadcom/phy-brcm-usb-init.h | 140 +++++++++++++++--
 drivers/phy/broadcom/phy-brcm-usb.c      |   6 +-
 3 files changed, 214 insertions(+), 123 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index 58882c10396a..80d6f54d276e 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -129,10 +129,6 @@ enum {
 	USB_CTRL_SELECTOR_COUNT,
 };
 
-#define USB_CTRL_REG(base, reg)	((void __iomem *)base + USB_CTRL_##reg)
-#define USB_XHCI_EC_REG(base, reg) ((void __iomem *)base + USB_XHCI_EC_##reg)
-#define USB_CTRL_MASK(reg, field) \
-	USB_CTRL_##reg##_##field##_MASK
 #define USB_CTRL_MASK_FAMILY(params, reg, field)			\
 	(params->usb_reg_bits_map[USB_CTRL_##reg##_##field##_SELECTOR])
 
@@ -143,13 +139,6 @@ enum {
 	usb_ctrl_unset_family(params, USB_CTRL_##reg,	\
 		USB_CTRL_##reg##_##field##_SELECTOR)
 
-#define USB_CTRL_SET(base, reg, field)	\
-	usb_ctrl_set(USB_CTRL_REG(base, reg),		\
-		     USB_CTRL_##reg##_##field##_MASK)
-#define USB_CTRL_UNSET(base, reg, field)	\
-	usb_ctrl_unset(USB_CTRL_REG(base, reg),		\
-		       USB_CTRL_##reg##_##field##_MASK)
-
 #define MDIO_USB2	0
 #define MDIO_USB3	BIT(31)
 
@@ -405,26 +394,14 @@ usb_reg_bits_map_table[BRCM_FAMILY_COUNT][USB_CTRL_SELECTOR_COUNT] = {
 	},
 };
 
-static inline u32 brcmusb_readl(void __iomem *addr)
-{
-	return readl(addr);
-}
-
-static inline void brcmusb_writel(u32 val, void __iomem *addr)
-{
-	writel(val, addr);
-}
-
 static inline
 void usb_ctrl_unset_family(struct brcm_usb_init_params *params,
 			   u32 reg_offset, u32 field)
 {
 	u32 mask;
-	void __iomem *reg;
 
 	mask = params->usb_reg_bits_map[field];
-	reg = params->ctrl_regs + reg_offset;
-	brcmusb_writel(brcmusb_readl(reg) & ~mask, reg);
+	brcm_usb_ctrl_unset(params->ctrl_regs + reg_offset, mask);
 };
 
 static inline
@@ -432,45 +409,27 @@ void usb_ctrl_set_family(struct brcm_usb_init_params *params,
 			 u32 reg_offset, u32 field)
 {
 	u32 mask;
-	void __iomem *reg;
 
 	mask = params->usb_reg_bits_map[field];
-	reg = params->ctrl_regs + reg_offset;
-	brcmusb_writel(brcmusb_readl(reg) | mask, reg);
+	brcm_usb_ctrl_set(params->ctrl_regs + reg_offset, mask);
 };
 
-static inline void usb_ctrl_set(void __iomem *reg, u32 field)
-{
-	u32 value;
-
-	value = brcmusb_readl(reg);
-	brcmusb_writel(value | field, reg);
-}
-
-static inline void usb_ctrl_unset(void __iomem *reg, u32 field)
-{
-	u32 value;
-
-	value = brcmusb_readl(reg);
-	brcmusb_writel(value & ~field, reg);
-}
-
 static u32 brcmusb_usb_mdio_read(void __iomem *ctrl_base, u32 reg, int mode)
 {
 	u32 data;
 
 	data = (reg << 16) | mode;
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	data |= (1 << 24);
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	data &= ~(1 << 24);
 	/* wait for the 60MHz parallel to serial shifter */
 	usleep_range(10, 20);
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	/* wait for the 60MHz parallel to serial shifter */
 	usleep_range(10, 20);
 
-	return brcmusb_readl(USB_CTRL_REG(ctrl_base, MDIO2)) & 0xffff;
+	return brcm_usb_readl(USB_CTRL_REG(ctrl_base, MDIO2)) & 0xffff;
 }
 
 static void brcmusb_usb_mdio_write(void __iomem *ctrl_base, u32 reg,
@@ -479,14 +438,14 @@ static void brcmusb_usb_mdio_write(void __iomem *ctrl_base, u32 reg,
 	u32 data;
 
 	data = (reg << 16) | val | mode;
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	data |= (1 << 25);
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	data &= ~(1 << 25);
 
 	/* wait for the 60MHz parallel to serial shifter */
 	usleep_range(10, 20);
-	brcmusb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
+	brcm_usb_writel(data, USB_CTRL_REG(ctrl_base, MDIO));
 	/* wait for the 60MHz parallel to serial shifter */
 	usleep_range(10, 20);
 }
@@ -713,12 +672,12 @@ static void brcmusb_usb3_otp_fix(struct brcm_usb_init_params *params)
 
 	if (params->family_id != 0x74371000 || !xhci_ec_base)
 		return;
-	brcmusb_writel(0xa20c, USB_XHCI_EC_REG(xhci_ec_base, IRAADR));
-	val = brcmusb_readl(USB_XHCI_EC_REG(xhci_ec_base, IRADAT));
+	brcm_usb_writel(0xa20c, USB_XHCI_EC_REG(xhci_ec_base, IRAADR));
+	val = brcm_usb_readl(USB_XHCI_EC_REG(xhci_ec_base, IRADAT));
 
 	/* set cfg_pick_ss_lock */
 	val |= (1 << 27);
-	brcmusb_writel(val, USB_XHCI_EC_REG(xhci_ec_base, IRADAT));
+	brcm_usb_writel(val, USB_XHCI_EC_REG(xhci_ec_base, IRADAT));
 
 	/* Reset USB 3.0 PHY for workaround to take effect */
 	USB_CTRL_UNSET(params->ctrl_regs, USB30_CTL1, PHY3_RESETB);
@@ -751,7 +710,7 @@ static void brcmusb_xhci_soft_reset(struct brcm_usb_init_params *params,
  *   - default chip/rev.
  * NOTE: The minor rev is always ignored.
  */
-static enum brcm_family_type brcmusb_get_family_type(
+static enum brcm_family_type get_family_type(
 	struct brcm_usb_init_params *params)
 {
 	int last_type = -1;
@@ -779,7 +738,7 @@ static enum brcm_family_type brcmusb_get_family_type(
 	return last_type;
 }
 
-void brcm_usb_init_ipp(struct brcm_usb_init_params *params)
+static void usb_init_ipp(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->ctrl_regs;
 	u32 reg;
@@ -795,7 +754,7 @@ void brcm_usb_init_ipp(struct brcm_usb_init_params *params)
 			USB_CTRL_SET_FAMILY(params, USB30_CTL1, USB3_IPP);
 	}
 
-	reg = brcmusb_readl(USB_CTRL_REG(ctrl, SETUP));
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
 	orig_reg = reg;
 	if (USB_CTRL_MASK_FAMILY(params, SETUP, STRAP_CC_DRD_MODE_ENABLE_SEL))
 		/* Never use the strap, it's going away. */
@@ -803,8 +762,8 @@ void brcm_usb_init_ipp(struct brcm_usb_init_params *params)
 					      SETUP,
 					      STRAP_CC_DRD_MODE_ENABLE_SEL));
 	if (USB_CTRL_MASK_FAMILY(params, SETUP, STRAP_IPP_SEL))
+		/* override ipp strap pin (if it exits) */
 		if (params->ipp != 2)
-			/* override ipp strap pin (if it exits) */
 			reg &= ~(USB_CTRL_MASK_FAMILY(params, SETUP,
 						      STRAP_IPP_SEL));
 
@@ -812,54 +771,26 @@ void brcm_usb_init_ipp(struct brcm_usb_init_params *params)
 	reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
 	if (params->ioc)
 		reg |= USB_CTRL_MASK(SETUP, IOC);
-	if (params->ipp == 1 && ((reg & USB_CTRL_MASK(SETUP, IPP)) == 0))
+	if (params->ipp == 1)
 		reg |= USB_CTRL_MASK(SETUP, IPP);
-	brcmusb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
 
 	/*
 	 * If we're changing IPP, make sure power is off long enough
 	 * to turn off any connected devices.
 	 */
-	if (reg != orig_reg)
+	if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
 		msleep(50);
 }
 
-int brcm_usb_init_get_dual_select(struct brcm_usb_init_params *params)
-{
-	void __iomem *ctrl = params->ctrl_regs;
-	u32 reg = 0;
-
-	if (USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1, PORT_MODE)) {
-		reg = brcmusb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
-		reg &= USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1,
-					PORT_MODE);
-	}
-	return reg;
-}
-
-void brcm_usb_init_set_dual_select(struct brcm_usb_init_params *params,
-				   int mode)
-{
-	void __iomem *ctrl = params->ctrl_regs;
-	u32 reg;
-
-	if (USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1, PORT_MODE)) {
-		reg = brcmusb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
-		reg &= ~USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1,
-					PORT_MODE);
-		reg |= mode;
-		brcmusb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
-	}
-}
-
-void brcm_usb_init_common(struct brcm_usb_init_params *params)
+static void usb_init_common(struct brcm_usb_init_params *params)
 {
 	u32 reg;
 	void __iomem *ctrl = params->ctrl_regs;
 
 	/* Clear any pending wake conditions */
-	reg = brcmusb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
-	brcmusb_writel(reg, USB_CTRL_REG(ctrl, USB_PM_STATUS));
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_PM_STATUS));
 
 	/* Take USB out of power down */
 	if (USB_CTRL_MASK_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN)) {
@@ -885,7 +816,7 @@ void brcm_usb_init_common(struct brcm_usb_init_params *params)
 	/* Block auto PLL suspend by USB2 PHY (Sasi) */
 	USB_CTRL_SET(ctrl, PLL_CTL, PLL_SUSPEND_EN);
 
-	reg = brcmusb_readl(USB_CTRL_REG(ctrl, SETUP));
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
 	if (params->selected_family == BRCM_FAMILY_7364A0)
 		/* Suppress overcurrent indication from USB30 ports for A0 */
 		reg |= USB_CTRL_MASK_FAMILY(params, SETUP, OC3_DISABLE);
@@ -901,16 +832,16 @@ void brcm_usb_init_common(struct brcm_usb_init_params *params)
 		reg |= USB_CTRL_MASK_FAMILY(params, SETUP, SCB1_EN);
 	if (USB_CTRL_MASK_FAMILY(params, SETUP, SCB2_EN))
 		reg |= USB_CTRL_MASK_FAMILY(params, SETUP, SCB2_EN);
-	brcmusb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
 
 	brcmusb_memc_fix(params);
 
 	if (USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1, PORT_MODE)) {
-		reg = brcmusb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
 		reg &= ~USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1,
 					PORT_MODE);
 		reg |= params->mode;
-		brcmusb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+		brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
 	}
 	if (USB_CTRL_MASK_FAMILY(params, USB_PM, BDC_SOFT_RESETB)) {
 		switch (params->mode) {
@@ -932,7 +863,7 @@ void brcm_usb_init_common(struct brcm_usb_init_params *params)
 	}
 }
 
-void brcm_usb_init_eohci(struct brcm_usb_init_params *params)
+static void usb_init_eohci(struct brcm_usb_init_params *params)
 {
 	u32 reg;
 	void __iomem *ctrl = params->ctrl_regs;
@@ -948,10 +879,10 @@ void brcm_usb_init_eohci(struct brcm_usb_init_params *params)
 		USB_CTRL_SET(ctrl, EBRIDGE, ESTOP_SCB_REQ);
 
 	/* Setup the endian bits */
-	reg = brcmusb_readl(USB_CTRL_REG(ctrl, SETUP));
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
 	reg &= ~USB_CTRL_SETUP_ENDIAN_BITS;
 	reg |= USB_CTRL_MASK_FAMILY(params, SETUP, ENDIAN);
-	brcmusb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
 
 	if (params->selected_family == BRCM_FAMILY_7271A0)
 		/* Enable LS keep alive fix for certain keyboards */
@@ -962,14 +893,14 @@ void brcm_usb_init_eohci(struct brcm_usb_init_params *params)
 		 * Make the burst size 512 bytes to fix a hardware bug
 		 * on the 7255a0. See HW7255-24.
 		 */
-		reg = brcmusb_readl(USB_CTRL_REG(ctrl, EBRIDGE));
+		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, EBRIDGE));
 		reg &= ~USB_CTRL_MASK(EBRIDGE, EBR_SCB_SIZE);
 		reg |= 0x800;
-		brcmusb_writel(reg, USB_CTRL_REG(ctrl, EBRIDGE));
+		brcm_usb_writel(reg, USB_CTRL_REG(ctrl, EBRIDGE));
 	}
 }
 
-void brcm_usb_init_xhci(struct brcm_usb_init_params *params)
+static void usb_init_xhci(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->ctrl_regs;
 
@@ -997,7 +928,7 @@ void brcm_usb_init_xhci(struct brcm_usb_init_params *params)
 	brcmusb_usb3_otp_fix(params);
 }
 
-void brcm_usb_uninit_common(struct brcm_usb_init_params *params)
+static void usb_uninit_common(struct brcm_usb_init_params *params)
 {
 	if (USB_CTRL_MASK_FAMILY(params, USB_PM, USB_PWRDN))
 		USB_CTRL_SET_FAMILY(params, USB_PM, USB_PWRDN);
@@ -1006,17 +937,47 @@ void brcm_usb_uninit_common(struct brcm_usb_init_params *params)
 		USB_CTRL_SET_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN);
 }
 
-void brcm_usb_uninit_eohci(struct brcm_usb_init_params *params)
+static void usb_uninit_eohci(struct brcm_usb_init_params *params)
 {
 }
 
-void brcm_usb_uninit_xhci(struct brcm_usb_init_params *params)
+static void usb_uninit_xhci(struct brcm_usb_init_params *params)
 {
 	brcmusb_xhci_soft_reset(params, 1);
 	USB_CTRL_SET(params->ctrl_regs, USB30_PCTL, PHY3_IDDQ_OVERRIDE);
 }
 
-void brcm_usb_wake_enable(struct brcm_usb_init_params *params,
+static int usb_get_dual_select(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+	u32 reg = 0;
+
+	pr_debug("%s\n", __func__);
+	if (USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1, PORT_MODE)) {
+		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+		reg &= USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1,
+					PORT_MODE);
+	}
+	return reg;
+}
+
+static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+	u32 reg;
+
+	pr_debug("%s\n", __func__);
+
+	if (USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1, PORT_MODE)) {
+		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+		reg &= ~USB_CTRL_MASK_FAMILY(params, USB_DEVICE_CTL1,
+					PORT_MODE);
+		reg |= mode;
+		brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+	}
+}
+
+static void usb_wake_enable(struct brcm_usb_init_params *params,
 			  int enable)
 {
 	void __iomem *ctrl = params->ctrl_regs;
@@ -1027,13 +988,29 @@ void brcm_usb_wake_enable(struct brcm_usb_init_params *params,
 		USB_CTRL_UNSET(ctrl, USB_PM, RMTWKUP_EN);
 }
 
-void brcm_usb_set_family_map(struct brcm_usb_init_params *params)
+static const struct brcm_usb_init_ops bcm7445_ops = {
+	.init_ipp = usb_init_ipp,
+	.init_common = usb_init_common,
+	.init_eohci = usb_init_eohci,
+	.init_xhci = usb_init_xhci,
+	.uninit_common = usb_uninit_common,
+	.uninit_eohci = usb_uninit_eohci,
+	.uninit_xhci = usb_uninit_xhci,
+	.get_dual_select = usb_get_dual_select,
+	.set_dual_select = usb_set_dual_select,
+	.wake_enable = usb_wake_enable,
+};
+
+void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params)
 {
 	int fam;
 
-	fam = brcmusb_get_family_type(params);
+	pr_debug("%s\n", __func__);
+
+	fam = get_family_type(params);
 	params->selected_family = fam;
 	params->usb_reg_bits_map =
 		&usb_reg_bits_map_table[fam][0];
 	params->family_name = family_names[fam];
+	params->ops = &bcm7445_ops;
 }
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index f473e0c51f0b..7701872d1136 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -13,6 +13,33 @@
 
 struct  brcm_usb_init_params;
 
+#define USB_CTRL_REG(base, reg)	((void __iomem *)base + USB_CTRL_##reg)
+#define USB_XHCI_EC_REG(base, reg) ((void __iomem *)base + USB_XHCI_EC_##reg)
+#define USB_CTRL_MASK(reg, field) \
+	USB_CTRL_##reg##_##field##_MASK
+#define USB_CTRL_SET(base, reg, field)	\
+	brcm_usb_ctrl_set(USB_CTRL_REG(base, reg),	\
+			  USB_CTRL_##reg##_##field##_MASK)
+#define USB_CTRL_UNSET(base, reg, field)	\
+	brcm_usb_ctrl_unset(USB_CTRL_REG(base, reg),		\
+			    USB_CTRL_##reg##_##field##_MASK)
+
+struct  brcm_usb_init_params;
+
+struct brcm_usb_init_ops {
+	void (*init_ipp)(struct brcm_usb_init_params *params);
+	void (*init_common)(struct brcm_usb_init_params *params);
+	void (*init_eohci)(struct brcm_usb_init_params *params);
+	void (*init_xhci)(struct brcm_usb_init_params *params);
+	void (*uninit_common)(struct brcm_usb_init_params *params);
+	void (*uninit_eohci)(struct brcm_usb_init_params *params);
+	void (*uninit_xhci)(struct brcm_usb_init_params *params);
+	int  (*get_dual_select)(struct brcm_usb_init_params *params);
+	void (*set_dual_select)(struct brcm_usb_init_params *params, int mode);
+	void (*wake_enable)(struct brcm_usb_init_params *params,
+			    int enable);
+};
+
 struct  brcm_usb_init_params {
 	void __iomem *ctrl_regs;
 	void __iomem *xhci_ec_regs;
@@ -24,20 +51,107 @@ struct  brcm_usb_init_params {
 	int selected_family;
 	const char *family_name;
 	const u32 *usb_reg_bits_map;
+	const struct brcm_usb_init_ops *ops;
 };
 
-void brcm_usb_set_family_map(struct brcm_usb_init_params *params);
-int brcm_usb_init_get_dual_select(struct brcm_usb_init_params *params);
-void brcm_usb_init_set_dual_select(struct brcm_usb_init_params *params,
-				   int mode);
-
-void brcm_usb_init_ipp(struct brcm_usb_init_params *ini);
-void brcm_usb_init_common(struct brcm_usb_init_params *ini);
-void brcm_usb_init_eohci(struct brcm_usb_init_params *ini);
-void brcm_usb_init_xhci(struct brcm_usb_init_params *ini);
-void brcm_usb_uninit_common(struct brcm_usb_init_params *ini);
-void brcm_usb_uninit_eohci(struct brcm_usb_init_params *ini);
-void brcm_usb_uninit_xhci(struct brcm_usb_init_params *ini);
-void brcm_usb_wake_enable(struct brcm_usb_init_params *params, int enable);
+void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
+
+static inline u32 brcm_usb_readl(void __iomem *addr)
+{
+	/*
+	 * MIPS endianness is configured by boot strap, which also reverses all
+	 * bus endianness (i.e., big-endian CPU + big endian bus ==> native
+	 * endian I/O).
+	 *
+	 * Other architectures (e.g., ARM) either do not support big endian, or
+	 * else leave I/O in little endian mode.
+	 */
+	if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(__BIG_ENDIAN))
+		return __raw_readl(addr);
+	else
+		return readl_relaxed(addr);
+}
+
+static inline void brcm_usb_writel(u32 val, void __iomem *addr)
+{
+	/* See brcmnand_readl() comments */
+	if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(__BIG_ENDIAN))
+		__raw_writel(val, addr);
+	else
+		writel_relaxed(val, addr);
+}
+
+static inline void brcm_usb_ctrl_unset(void __iomem *reg, u32 mask)
+{
+	brcm_usb_writel(brcm_usb_readl(reg) & ~(mask), reg);
+};
+
+static inline void brcm_usb_ctrl_set(void __iomem *reg, u32 mask)
+{
+	brcm_usb_writel(brcm_usb_readl(reg) | (mask), reg);
+};
+
+static inline void brcm_usb_init_ipp(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->init_ipp)
+		ini->ops->init_ipp(ini);
+}
+
+static inline void brcm_usb_init_common(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->init_common)
+		ini->ops->init_common(ini);
+}
+
+static inline void brcm_usb_init_eohci(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->init_eohci)
+		ini->ops->init_eohci(ini);
+}
+
+static inline void brcm_usb_init_xhci(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->init_xhci)
+		ini->ops->init_xhci(ini);
+}
+
+static inline void brcm_usb_uninit_common(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->uninit_common)
+		ini->ops->uninit_common(ini);
+}
+
+static inline void brcm_usb_uninit_eohci(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->uninit_eohci)
+		ini->ops->uninit_eohci(ini);
+}
+
+static inline void brcm_usb_uninit_xhci(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->uninit_xhci)
+		ini->ops->uninit_xhci(ini);
+}
+
+static inline void brcm_usb_wake_enable(struct brcm_usb_init_params *ini,
+	int enable)
+{
+	if (ini->ops->wake_enable)
+		ini->ops->wake_enable(ini, enable);
+}
+
+static inline int brcm_usb_get_dual_select(struct brcm_usb_init_params *ini)
+{
+	if (ini->ops->get_dual_select)
+		return ini->ops->get_dual_select(ini);
+	return 0;
+}
+
+static inline void brcm_usb_set_dual_select(struct brcm_usb_init_params *ini,
+	int mode)
+{
+	if (ini->ops->set_dual_select)
+		ini->ops->set_dual_select(ini, mode);
+}
 
 #endif /* _USB_BRCM_COMMON_INIT_H */
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index cca04d60f2d2..9d93c5599511 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -207,7 +207,7 @@ static ssize_t dual_select_store(struct device *dev,
 	res = name_to_value(&brcm_dual_mode_to_name[0],
 			    ARRAY_SIZE(brcm_dual_mode_to_name), buf, &value);
 	if (!res) {
-		brcm_usb_init_set_dual_select(&priv->ini, value);
+		brcm_usb_set_dual_select(&priv->ini, value);
 		res = len;
 	}
 	mutex_unlock(&sysfs_lock);
@@ -222,7 +222,7 @@ static ssize_t dual_select_show(struct device *dev,
 	int value;
 
 	mutex_lock(&sysfs_lock);
-	value = brcm_usb_init_get_dual_select(&priv->ini);
+	value = brcm_usb_get_dual_select(&priv->ini);
 	mutex_unlock(&sysfs_lock);
 	return sprintf(buf, "%s\n",
 		value_to_name(&brcm_dual_mode_to_name[0],
@@ -331,7 +331,7 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 
 	priv->ini.family_id = brcmstb_get_family_id();
 	priv->ini.product_id = brcmstb_get_product_id();
-	brcm_usb_set_family_map(&priv->ini);
+	brcm_usb_dvr_init_7445(&priv->ini);
 	dev_dbg(dev, "Best mapping table is for %s\n",
 		priv->ini.family_name);
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 06/13] dt-bindings: Add Broadcom STB USB PHY binding document

[Al Cooper]

Add support for bcm7216 and bcm7211

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 .../bindings/phy/brcm,brcmstb-usb-phy.txt     | 69 +++++++++++++++----
 1 file changed, 56 insertions(+), 13 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
index 24a0d06acd1d..698aacbdcfc4 100644
--- a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
+++ b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
@@ -1,30 +1,49 @@
 Broadcom STB USB PHY
 
 Required properties:
- - compatible: brcm,brcmstb-usb-phy
- - reg: two offset and length pairs.
-	The first pair specifies a manditory set of memory mapped
-	registers used for general control of the PHY.
-	The second pair specifies optional registers used by some of
-	the SoCs that support USB 3.x
- - #phy-cells: Shall be 1 as it expects one argument for setting
-	       the type of the PHY. Possible values are:
-	       - PHY_TYPE_USB2 for USB1.1/2.0 PHY
-	       - PHY_TYPE_USB3 for USB3.x PHY
+- compatible: should be one of
+	"brcm,brcmstb-usb-phy"
+	"brcm,bcm7216-usb-phy"
+	"brcm,bcm7211-usb-phy"
+
+- reg and reg-names properties requirements are specific to the
+  compatible string.
+  "brcm,brcmstb-usb-phy":
+    - reg: 1 or 2 offset and length pairs. One for the base CTRL registers
+           and an optional pair for systems with USB 3.x support
+    - reg-names: not specified
+  "brcm,bcm7216-usb-phy":
+    - reg: 3 offset and length pairs for CTRL, XHCI_EC and XHCI_GBL
+           registers
+    - reg-names: "ctrl", "xhci_ec", "xhci_gbl"
+  "brcm,bcm7211-usb-phy":
+    - reg: 5 offset and length pairs for CTRL, XHCI_EC, XHCI_GBL,
+           USB_PHY and USB_MDIO registers and an optional pair
+	   for the BDC registers
+    - reg-names: "ctrl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio", "bdc_ec"
+
+- #phy-cells: Shall be 1 as it expects one argument for setting
+	      the type of the PHY. Possible values are:
+	      - PHY_TYPE_USB2 for USB1.1/2.0 PHY
+	      - PHY_TYPE_USB3 for USB3.x PHY
 
 Optional Properties:
 - clocks : clock phandles.
 - clock-names: String, clock name.
+- interrupts: wakeup interrupt
+- interrupt-names: "wakeup"
 - brcm,ipp: Boolean, Invert Port Power.
   Possible values are: 0 (Don't invert), 1 (Invert)
 - brcm,ioc: Boolean, Invert Over Current detection.
   Possible values are: 0 (Don't invert), 1 (Invert)
-NOTE: one or both of the following two properties must be set
-- brcm,has-xhci: Boolean indicating the phy has an XHCI phy.
-- brcm,has-eohci: Boolean indicating the phy has an EHCI/OHCI phy.
 - dr_mode: String, PHY Device mode.
   Possible values are: "host", "peripheral ", "drd" or "typec-pd"
   If this property is not defined, the phy will default to "host" mode.
+- brcm,syscon-piarbctl: phandle to syscon for handling config registers
+NOTE: one or both of the following two properties must be set
+- brcm,has-xhci: Boolean indicating the phy has an XHCI phy.
+- brcm,has-eohci: Boolean indicating the phy has an EHCI/OHCI phy.
+
 
 Example:
 
@@ -41,3 +60,27 @@ usbphy_0: usb-phy@f0470200 {
 	clocks = <&usb20>, <&usb30>;
 	clock-names = "sw_usb", "sw_usb3";
 };
+
+usb-phy@29f0200 {
+	reg = <0x29f0200 0x200>,
+		<0x29c0880 0x30>,
+		<0x29cc100 0x534>,
+		<0x2808000 0x24>,
+		<0x2980080 0x8>;
+	reg-names = "ctrl",
+		"xhci_ec",
+		"xhci_gbl",
+		"usb_phy",
+		"usb_mdio";
+	brcm,ioc = <0x0>;
+	brcm,ipp = <0x0>;
+	compatible = "brcm,bcm7211-usb-phy";
+	interrupts = <0x30>;
+	interrupt-parent = <&vpu_intr1_nosec_intc>;
+	interrupt-names = "wake";
+	#phy-cells = <0x1>;
+	brcm,has-xhci;
+	syscon-piarbctl = <&syscon_piarbctl>;
+	clocks = <&scmi_clk 256>;
+	clock-names = "sw_usb";
+};
-- 
2.17.1

[PATCH v3 06/13] dt-bindings: Add Broadcom STB USB PHY binding document

[Al Cooper]

Add support for bcm7216 and bcm7211

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 .../bindings/phy/brcm,brcmstb-usb-phy.txt     | 69 +++++++++++++++----
 1 file changed, 56 insertions(+), 13 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
index 24a0d06acd1d..698aacbdcfc4 100644
--- a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
+++ b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
@@ -1,30 +1,49 @@
 Broadcom STB USB PHY
 
 Required properties:
- - compatible: brcm,brcmstb-usb-phy
- - reg: two offset and length pairs.
-	The first pair specifies a manditory set of memory mapped
-	registers used for general control of the PHY.
-	The second pair specifies optional registers used by some of
-	the SoCs that support USB 3.x
- - #phy-cells: Shall be 1 as it expects one argument for setting
-	       the type of the PHY. Possible values are:
-	       - PHY_TYPE_USB2 for USB1.1/2.0 PHY
-	       - PHY_TYPE_USB3 for USB3.x PHY
+- compatible: should be one of
+	"brcm,brcmstb-usb-phy"
+	"brcm,bcm7216-usb-phy"
+	"brcm,bcm7211-usb-phy"
+
+- reg and reg-names properties requirements are specific to the
+  compatible string.
+  "brcm,brcmstb-usb-phy":
+    - reg: 1 or 2 offset and length pairs. One for the base CTRL registers
+           and an optional pair for systems with USB 3.x support
+    - reg-names: not specified
+  "brcm,bcm7216-usb-phy":
+    - reg: 3 offset and length pairs for CTRL, XHCI_EC and XHCI_GBL
+           registers
+    - reg-names: "ctrl", "xhci_ec", "xhci_gbl"
+  "brcm,bcm7211-usb-phy":
+    - reg: 5 offset and length pairs for CTRL, XHCI_EC, XHCI_GBL,
+           USB_PHY and USB_MDIO registers and an optional pair
+	   for the BDC registers
+    - reg-names: "ctrl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio", "bdc_ec"
+
+- #phy-cells: Shall be 1 as it expects one argument for setting
+	      the type of the PHY. Possible values are:
+	      - PHY_TYPE_USB2 for USB1.1/2.0 PHY
+	      - PHY_TYPE_USB3 for USB3.x PHY
 
 Optional Properties:
 - clocks : clock phandles.
 - clock-names: String, clock name.
+- interrupts: wakeup interrupt
+- interrupt-names: "wakeup"
 - brcm,ipp: Boolean, Invert Port Power.
   Possible values are: 0 (Don't invert), 1 (Invert)
 - brcm,ioc: Boolean, Invert Over Current detection.
   Possible values are: 0 (Don't invert), 1 (Invert)
-NOTE: one or both of the following two properties must be set
-- brcm,has-xhci: Boolean indicating the phy has an XHCI phy.
-- brcm,has-eohci: Boolean indicating the phy has an EHCI/OHCI phy.
 - dr_mode: String, PHY Device mode.
   Possible values are: "host", "peripheral ", "drd" or "typec-pd"
   If this property is not defined, the phy will default to "host" mode.
+- brcm,syscon-piarbctl: phandle to syscon for handling config registers
+NOTE: one or both of the following two properties must be set
+- brcm,has-xhci: Boolean indicating the phy has an XHCI phy.
+- brcm,has-eohci: Boolean indicating the phy has an EHCI/OHCI phy.
+
 
 Example:
 
@@ -41,3 +60,27 @@ usbphy_0: usb-phy@f0470200 {
 	clocks = <&usb20>, <&usb30>;
 	clock-names = "sw_usb", "sw_usb3";
 };
+
+usb-phy@29f0200 {
+	reg = <0x29f0200 0x200>,
+		<0x29c0880 0x30>,
+		<0x29cc100 0x534>,
+		<0x2808000 0x24>,
+		<0x2980080 0x8>;
+	reg-names = "ctrl",
+		"xhci_ec",
+		"xhci_gbl",
+		"usb_phy",
+		"usb_mdio";
+	brcm,ioc = <0x0>;
+	brcm,ipp = <0x0>;
+	compatible = "brcm,bcm7211-usb-phy";
+	interrupts = <0x30>;
+	interrupt-parent = <&vpu_intr1_nosec_intc>;
+	interrupt-names = "wake";
+	#phy-cells = <0x1>;
+	brcm,has-xhci;
+	syscon-piarbctl = <&syscon_piarbctl>;
+	clocks = <&scmi_clk 256>;
+	clock-names = "sw_usb";
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 06/13] dt-bindings: Add Broadcom STB USB PHY binding document

[Rob Herring]

On Tue, 10 Dec 2019 08:21:25 -0500, Al Cooper wrote:
> Add support for bcm7216 and bcm7211
> 
> Signed-off-by: Al Cooper <alcooperx@gmail.com>
> ---
>  .../bindings/phy/brcm,brcmstb-usb-phy.txt     | 69 +++++++++++++++----
>  1 file changed, 56 insertions(+), 13 deletions(-)
> 

Please add Acked-by/Reviewed-by tags when posting new versions. However,
there's no need to repost patches *only* to add the tags. The upstream
maintainer will do that for acks received on the version they apply.

If a tag was not added on purpose, please state why and what changed.

Re: [PATCH v3 06/13] dt-bindings: Add Broadcom STB USB PHY binding document

[Rob Herring]

On Tue, 10 Dec 2019 08:21:25 -0500, Al Cooper wrote:
> Add support for bcm7216 and bcm7211
> 
> Signed-off-by: Al Cooper <alcooperx@gmail.com>
> ---
>  .../bindings/phy/brcm,brcmstb-usb-phy.txt     | 69 +++++++++++++++----
>  1 file changed, 56 insertions(+), 13 deletions(-)
> 

Please add Acked-by/Reviewed-by tags when posting new versions. However,
there's no need to repost patches *only* to add the tags. The upstream
maintainer will do that for acks received on the version they apply.

If a tag was not added on purpose, please state why and what changed.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 07/13] phy: usb: Add support for new Synopsis USB controller on the 7216

[Al Cooper]

The 7216 has the new USB XHCI controller from Synopsis. While
this new controller and the PHY are similar to the STB versions,
the major differences are:

- Many of the registers and fields in the CTRL block have been
  removed or changed.
- A new set of Synopsis control registers, BCHP_USB_XHCI_GBL, were
  added.
- MDIO functionality has been replaced with direct access registers
  in the BCHP_USB_XHCI_GBL block.
- Power up PHY defaults that had to be changed by MDIO in previous
  chips will now power up with the correct defaults.

A new init module was created for this new Synopsis USB controller.
A new compatible string was added and the driver will dispatch
into one of two init modules based on it. A "reg-names" field was
added so the driver can more easily get optional registers.
A DT bindings document was also added for this driver.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/Makefile                 |   2 +-
 .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 171 ++++++++++++++++++
 drivers/phy/broadcom/phy-brcm-usb-init.h      |   2 +
 drivers/phy/broadcom/phy-brcm-usb.c           |  70 +++++--
 4 files changed, 227 insertions(+), 18 deletions(-)
 create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c

diff --git a/drivers/phy/broadcom/Makefile b/drivers/phy/broadcom/Makefile
index f453c7d3ffff..88523e2be861 100644
--- a/drivers/phy/broadcom/Makefile
+++ b/drivers/phy/broadcom/Makefile
@@ -8,7 +8,7 @@ obj-$(CONFIG_PHY_NS2_USB_DRD)		+= phy-bcm-ns2-usbdrd.o
 obj-$(CONFIG_PHY_BRCM_SATA)		+= phy-brcm-sata.o
 obj-$(CONFIG_PHY_BRCM_USB)		+= phy-brcm-usb-dvr.o
 
-phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o
+phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o phy-brcm-usb-init-synopsis.o
 
 obj-$(CONFIG_PHY_BCM_SR_PCIE)		+= phy-bcm-sr-pcie.o
 obj-$(CONFIG_PHY_BCM_SR_USB)		+= phy-bcm-sr-usb.o
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
new file mode 100644
index 000000000000..57663492b228
--- /dev/null
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -0,0 +1,171 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2018, Broadcom */
+
+/*
+ * This module contains USB PHY initialization for power up and S3 resume
+ * for newer Synopsis based USB hardware first used on the bcm7216.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+
+#include <linux/soc/brcmstb/brcmstb.h>
+#include "phy-brcm-usb-init.h"
+
+/* Register definitions for the USB CTRL block */
+#define USB_CTRL_SETUP			0x00
+#define   USB_CTRL_SETUP_STRAP_IPP_SEL_MASK		0x02000000
+#define   USB_CTRL_SETUP_SCB2_EN_MASK			0x00008000
+#define   USB_CTRL_SETUP_SCB1_EN_MASK			0x00004000
+#define   USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK		0x00000200
+#define   USB_CTRL_SETUP_IPP_MASK			0x00000020
+#define   USB_CTRL_SETUP_IOC_MASK			0x00000010
+#define USB_CTRL_USB_PM			0x04
+#define   USB_CTRL_USB_PM_USB_PWRDN_MASK		0x80000000
+#define   USB_CTRL_USB_PM_SOFT_RESET_MASK		0x40000000
+#define   USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK		0x00800000
+#define   USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK		0x00400000
+#define USB_CTRL_USB_PM_STATUS		0x08
+#define USB_CTRL_USB_DEVICE_CTL1	0x10
+#define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK	0x00000003
+
+
+static void xhci_soft_reset(struct brcm_usb_init_params *params,
+			int on_off)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+
+	/* Assert reset */
+	if (on_off)
+		USB_CTRL_UNSET(ctrl, USB_PM, XHC_SOFT_RESETB);
+	/* De-assert reset */
+	else
+		USB_CTRL_SET(ctrl, USB_PM, XHC_SOFT_RESETB);
+}
+
+static void usb_init_ipp(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+	u32 reg;
+	u32 orig_reg;
+
+	pr_debug("%s\n", __func__);
+
+	orig_reg = reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
+	if (params->ipp != 2)
+		/* override ipp strap pin (if it exits) */
+		reg &= ~(USB_CTRL_MASK(SETUP, STRAP_IPP_SEL));
+
+	/* Override the default OC and PP polarity */
+	reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
+	if (params->ioc)
+		reg |= USB_CTRL_MASK(SETUP, IOC);
+	if (params->ipp == 1)
+		reg |= USB_CTRL_MASK(SETUP, IPP);
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
+
+	/*
+	 * If we're changing IPP, make sure power is off long enough
+	 * to turn off any connected devices.
+	 */
+	if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
+		msleep(50);
+}
+
+static void usb_init_common(struct brcm_usb_init_params *params)
+{
+	u32 reg;
+	void __iomem *ctrl = params->ctrl_regs;
+
+	pr_debug("%s\n", __func__);
+
+	USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
+	/* 1 millisecond - for USB clocks to settle down */
+	usleep_range(1000, 2000);
+
+	if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
+		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+		reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
+		reg |= params->mode;
+		brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+	}
+	switch (params->mode) {
+	case USB_CTLR_MODE_HOST:
+		USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
+		break;
+	default:
+		USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
+		USB_CTRL_SET(ctrl, USB_PM, BDC_SOFT_RESETB);
+		break;
+	}
+}
+
+static void usb_init_xhci(struct brcm_usb_init_params *params)
+{
+	pr_debug("%s\n", __func__);
+
+	xhci_soft_reset(params, 0);
+}
+
+static void usb_uninit_common(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+
+	pr_debug("%s\n", __func__);
+
+	USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
+
+}
+
+static void usb_uninit_xhci(struct brcm_usb_init_params *params)
+{
+
+	pr_debug("%s\n", __func__);
+
+	xhci_soft_reset(params, 1);
+}
+
+static int usb_get_dual_select(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+	u32 reg = 0;
+
+	pr_debug("%s\n", __func__);
+
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+	reg &= USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
+	return reg;
+}
+
+static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+	u32 reg;
+
+	pr_debug("%s\n", __func__);
+
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+	reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
+	reg |= mode;
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+}
+
+
+static const struct brcm_usb_init_ops bcm7216_ops = {
+	.init_ipp = usb_init_ipp,
+	.init_common = usb_init_common,
+	.init_xhci = usb_init_xhci,
+	.uninit_common = usb_uninit_common,
+	.uninit_xhci = usb_uninit_xhci,
+	.get_dual_select = usb_get_dual_select,
+	.set_dual_select = usb_set_dual_select,
+};
+
+void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
+{
+
+	pr_debug("%s\n", __func__);
+
+	params->family_name = "7216";
+	params->ops = &bcm7216_ops;
+}
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index 7701872d1136..db6851c55335 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -43,6 +43,7 @@ struct brcm_usb_init_ops {
 struct  brcm_usb_init_params {
 	void __iomem *ctrl_regs;
 	void __iomem *xhci_ec_regs;
+	void __iomem *xhci_gbl_regs;
 	int ioc;
 	int ipp;
 	int mode;
@@ -55,6 +56,7 @@ struct  brcm_usb_init_params {
 };
 
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
+void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
 
 static inline u32 brcm_usb_readl(void __iomem *addr)
 {
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 9d93c5599511..64379ede480e 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -241,6 +241,15 @@ static const struct attribute_group brcm_usb_phy_group = {
 	.attrs = brcm_usb_phy_attrs,
 };
 
+static const struct of_device_id brcm_usb_dt_ids[] = {
+	{
+		.compatible = "brcm,bcm7216-usb-phy",
+		.data = &brcm_usb_dvr_init_7216,
+	},
+	{ .compatible = "brcm,brcmstb-usb-phy" },
+	{ /* sentinel */ }
+};
+
 static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 				 struct brcm_usb_phy_data *priv,
 				 struct device_node *dn)
@@ -316,13 +325,16 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 
 static int brcm_usb_phy_probe(struct platform_device *pdev)
 {
-	struct resource *res;
+	struct resource *res_ctrl;
+	struct resource *res_xhciec = NULL;
+	struct resource *res_xhcigbl = NULL;
 	struct device *dev = &pdev->dev;
 	struct brcm_usb_phy_data *priv;
 	struct phy_provider *phy_provider;
 	struct device_node *dn = pdev->dev.of_node;
 	int err;
 	const char *mode;
+	const struct of_device_id *match;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -331,30 +343,59 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 
 	priv->ini.family_id = brcmstb_get_family_id();
 	priv->ini.product_id = brcmstb_get_product_id();
-	brcm_usb_dvr_init_7445(&priv->ini);
+
+	match = of_match_node(brcm_usb_dt_ids, dev->of_node);
+	if (match && match->data) {
+		void (*dvr_init)(struct brcm_usb_init_params *params);
+
+		dvr_init = match->data;
+		(*dvr_init)(&priv->ini);
+	} else {
+		brcm_usb_dvr_init_7445(&priv->ini);
+	}
+
 	dev_dbg(dev, "Best mapping table is for %s\n",
 		priv->ini.family_name);
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(dev, "can't get USB_CTRL base address\n");
-		return -EINVAL;
+
+	/* Newer DT node has reg-names. xhci_ec and xhci_gbl are optional. */
+	res_ctrl = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
+	if (res_ctrl != NULL) {
+		res_xhciec = platform_get_resource_byname(pdev,
+							  IORESOURCE_MEM,
+							  "xhci_ec");
+		res_xhcigbl = platform_get_resource_byname(pdev,
+							   IORESOURCE_MEM,
+							   "xhci_gbl");
+	} else {
+		/* Older DT node without reg-names, use index */
+		res_ctrl = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		if (res_ctrl == NULL) {
+			dev_err(dev, "can't get CTRL base address\n");
+			return -EINVAL;
+		}
+		res_xhciec = platform_get_resource(pdev, IORESOURCE_MEM, 1);
 	}
-	priv->ini.ctrl_regs = devm_ioremap_resource(dev, res);
+	priv->ini.ctrl_regs = devm_ioremap_resource(dev, res_ctrl);
 	if (IS_ERR(priv->ini.ctrl_regs)) {
 		dev_err(dev, "can't map CTRL register space\n");
 		return -EINVAL;
 	}
-
-	/* The XHCI EC registers are optional */
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	if (res) {
+	if (res_xhciec) {
 		priv->ini.xhci_ec_regs =
-			devm_ioremap_resource(dev, res);
+			devm_ioremap_resource(dev, res_xhciec);
 		if (IS_ERR(priv->ini.xhci_ec_regs)) {
 			dev_err(dev, "can't map XHCI EC register space\n");
 			return -EINVAL;
 		}
 	}
+	if (res_xhcigbl) {
+		priv->ini.xhci_gbl_regs =
+			devm_ioremap_resource(dev, res_xhcigbl);
+		if (IS_ERR(priv->ini.xhci_gbl_regs)) {
+			dev_err(dev, "can't map XHCI Global register space\n");
+			return -EINVAL;
+		}
+	}
 
 	of_property_read_u32(dn, "brcm,ipp", &priv->ini.ipp);
 	of_property_read_u32(dn, "brcm,ioc", &priv->ini.ioc);
@@ -480,11 +521,6 @@ static const struct dev_pm_ops brcm_usb_phy_pm_ops = {
 	SET_LATE_SYSTEM_SLEEP_PM_OPS(brcm_usb_phy_suspend, brcm_usb_phy_resume)
 };
 
-static const struct of_device_id brcm_usb_dt_ids[] = {
-	{ .compatible = "brcm,brcmstb-usb-phy" },
-	{ /* sentinel */ }
-};
-
 MODULE_DEVICE_TABLE(of, brcm_usb_dt_ids);
 
 static struct platform_driver brcm_usb_driver = {
-- 
2.17.1

[PATCH v3 07/13] phy: usb: Add support for new Synopsis USB controller on the 7216

[Al Cooper]

The 7216 has the new USB XHCI controller from Synopsis. While
this new controller and the PHY are similar to the STB versions,
the major differences are:

- Many of the registers and fields in the CTRL block have been
  removed or changed.
- A new set of Synopsis control registers, BCHP_USB_XHCI_GBL, were
  added.
- MDIO functionality has been replaced with direct access registers
  in the BCHP_USB_XHCI_GBL block.
- Power up PHY defaults that had to be changed by MDIO in previous
  chips will now power up with the correct defaults.

A new init module was created for this new Synopsis USB controller.
A new compatible string was added and the driver will dispatch
into one of two init modules based on it. A "reg-names" field was
added so the driver can more easily get optional registers.
A DT bindings document was also added for this driver.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/Makefile                 |   2 +-
 .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 171 ++++++++++++++++++
 drivers/phy/broadcom/phy-brcm-usb-init.h      |   2 +
 drivers/phy/broadcom/phy-brcm-usb.c           |  70 +++++--
 4 files changed, 227 insertions(+), 18 deletions(-)
 create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c

diff --git a/drivers/phy/broadcom/Makefile b/drivers/phy/broadcom/Makefile
index f453c7d3ffff..88523e2be861 100644
--- a/drivers/phy/broadcom/Makefile
+++ b/drivers/phy/broadcom/Makefile
@@ -8,7 +8,7 @@ obj-$(CONFIG_PHY_NS2_USB_DRD)		+= phy-bcm-ns2-usbdrd.o
 obj-$(CONFIG_PHY_BRCM_SATA)		+= phy-brcm-sata.o
 obj-$(CONFIG_PHY_BRCM_USB)		+= phy-brcm-usb-dvr.o
 
-phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o
+phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o phy-brcm-usb-init-synopsis.o
 
 obj-$(CONFIG_PHY_BCM_SR_PCIE)		+= phy-bcm-sr-pcie.o
 obj-$(CONFIG_PHY_BCM_SR_USB)		+= phy-bcm-sr-usb.o
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
new file mode 100644
index 000000000000..57663492b228
--- /dev/null
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -0,0 +1,171 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2018, Broadcom */
+
+/*
+ * This module contains USB PHY initialization for power up and S3 resume
+ * for newer Synopsis based USB hardware first used on the bcm7216.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+
+#include <linux/soc/brcmstb/brcmstb.h>
+#include "phy-brcm-usb-init.h"
+
+/* Register definitions for the USB CTRL block */
+#define USB_CTRL_SETUP			0x00
+#define   USB_CTRL_SETUP_STRAP_IPP_SEL_MASK		0x02000000
+#define   USB_CTRL_SETUP_SCB2_EN_MASK			0x00008000
+#define   USB_CTRL_SETUP_SCB1_EN_MASK			0x00004000
+#define   USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK		0x00000200
+#define   USB_CTRL_SETUP_IPP_MASK			0x00000020
+#define   USB_CTRL_SETUP_IOC_MASK			0x00000010
+#define USB_CTRL_USB_PM			0x04
+#define   USB_CTRL_USB_PM_USB_PWRDN_MASK		0x80000000
+#define   USB_CTRL_USB_PM_SOFT_RESET_MASK		0x40000000
+#define   USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK		0x00800000
+#define   USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK		0x00400000
+#define USB_CTRL_USB_PM_STATUS		0x08
+#define USB_CTRL_USB_DEVICE_CTL1	0x10
+#define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK	0x00000003
+
+
+static void xhci_soft_reset(struct brcm_usb_init_params *params,
+			int on_off)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+
+	/* Assert reset */
+	if (on_off)
+		USB_CTRL_UNSET(ctrl, USB_PM, XHC_SOFT_RESETB);
+	/* De-assert reset */
+	else
+		USB_CTRL_SET(ctrl, USB_PM, XHC_SOFT_RESETB);
+}
+
+static void usb_init_ipp(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+	u32 reg;
+	u32 orig_reg;
+
+	pr_debug("%s\n", __func__);
+
+	orig_reg = reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
+	if (params->ipp != 2)
+		/* override ipp strap pin (if it exits) */
+		reg &= ~(USB_CTRL_MASK(SETUP, STRAP_IPP_SEL));
+
+	/* Override the default OC and PP polarity */
+	reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
+	if (params->ioc)
+		reg |= USB_CTRL_MASK(SETUP, IOC);
+	if (params->ipp == 1)
+		reg |= USB_CTRL_MASK(SETUP, IPP);
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
+
+	/*
+	 * If we're changing IPP, make sure power is off long enough
+	 * to turn off any connected devices.
+	 */
+	if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
+		msleep(50);
+}
+
+static void usb_init_common(struct brcm_usb_init_params *params)
+{
+	u32 reg;
+	void __iomem *ctrl = params->ctrl_regs;
+
+	pr_debug("%s\n", __func__);
+
+	USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
+	/* 1 millisecond - for USB clocks to settle down */
+	usleep_range(1000, 2000);
+
+	if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
+		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+		reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
+		reg |= params->mode;
+		brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+	}
+	switch (params->mode) {
+	case USB_CTLR_MODE_HOST:
+		USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
+		break;
+	default:
+		USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
+		USB_CTRL_SET(ctrl, USB_PM, BDC_SOFT_RESETB);
+		break;
+	}
+}
+
+static void usb_init_xhci(struct brcm_usb_init_params *params)
+{
+	pr_debug("%s\n", __func__);
+
+	xhci_soft_reset(params, 0);
+}
+
+static void usb_uninit_common(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+
+	pr_debug("%s\n", __func__);
+
+	USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
+
+}
+
+static void usb_uninit_xhci(struct brcm_usb_init_params *params)
+{
+
+	pr_debug("%s\n", __func__);
+
+	xhci_soft_reset(params, 1);
+}
+
+static int usb_get_dual_select(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+	u32 reg = 0;
+
+	pr_debug("%s\n", __func__);
+
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+	reg &= USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
+	return reg;
+}
+
+static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
+{
+	void __iomem *ctrl = params->ctrl_regs;
+	u32 reg;
+
+	pr_debug("%s\n", __func__);
+
+	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+	reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
+	reg |= mode;
+	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
+}
+
+
+static const struct brcm_usb_init_ops bcm7216_ops = {
+	.init_ipp = usb_init_ipp,
+	.init_common = usb_init_common,
+	.init_xhci = usb_init_xhci,
+	.uninit_common = usb_uninit_common,
+	.uninit_xhci = usb_uninit_xhci,
+	.get_dual_select = usb_get_dual_select,
+	.set_dual_select = usb_set_dual_select,
+};
+
+void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
+{
+
+	pr_debug("%s\n", __func__);
+
+	params->family_name = "7216";
+	params->ops = &bcm7216_ops;
+}
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index 7701872d1136..db6851c55335 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -43,6 +43,7 @@ struct brcm_usb_init_ops {
 struct  brcm_usb_init_params {
 	void __iomem *ctrl_regs;
 	void __iomem *xhci_ec_regs;
+	void __iomem *xhci_gbl_regs;
 	int ioc;
 	int ipp;
 	int mode;
@@ -55,6 +56,7 @@ struct  brcm_usb_init_params {
 };
 
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
+void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
 
 static inline u32 brcm_usb_readl(void __iomem *addr)
 {
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 9d93c5599511..64379ede480e 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -241,6 +241,15 @@ static const struct attribute_group brcm_usb_phy_group = {
 	.attrs = brcm_usb_phy_attrs,
 };
 
+static const struct of_device_id brcm_usb_dt_ids[] = {
+	{
+		.compatible = "brcm,bcm7216-usb-phy",
+		.data = &brcm_usb_dvr_init_7216,
+	},
+	{ .compatible = "brcm,brcmstb-usb-phy" },
+	{ /* sentinel */ }
+};
+
 static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 				 struct brcm_usb_phy_data *priv,
 				 struct device_node *dn)
@@ -316,13 +325,16 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 
 static int brcm_usb_phy_probe(struct platform_device *pdev)
 {
-	struct resource *res;
+	struct resource *res_ctrl;
+	struct resource *res_xhciec = NULL;
+	struct resource *res_xhcigbl = NULL;
 	struct device *dev = &pdev->dev;
 	struct brcm_usb_phy_data *priv;
 	struct phy_provider *phy_provider;
 	struct device_node *dn = pdev->dev.of_node;
 	int err;
 	const char *mode;
+	const struct of_device_id *match;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -331,30 +343,59 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 
 	priv->ini.family_id = brcmstb_get_family_id();
 	priv->ini.product_id = brcmstb_get_product_id();
-	brcm_usb_dvr_init_7445(&priv->ini);
+
+	match = of_match_node(brcm_usb_dt_ids, dev->of_node);
+	if (match && match->data) {
+		void (*dvr_init)(struct brcm_usb_init_params *params);
+
+		dvr_init = match->data;
+		(*dvr_init)(&priv->ini);
+	} else {
+		brcm_usb_dvr_init_7445(&priv->ini);
+	}
+
 	dev_dbg(dev, "Best mapping table is for %s\n",
 		priv->ini.family_name);
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(dev, "can't get USB_CTRL base address\n");
-		return -EINVAL;
+
+	/* Newer DT node has reg-names. xhci_ec and xhci_gbl are optional. */
+	res_ctrl = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
+	if (res_ctrl != NULL) {
+		res_xhciec = platform_get_resource_byname(pdev,
+							  IORESOURCE_MEM,
+							  "xhci_ec");
+		res_xhcigbl = platform_get_resource_byname(pdev,
+							   IORESOURCE_MEM,
+							   "xhci_gbl");
+	} else {
+		/* Older DT node without reg-names, use index */
+		res_ctrl = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		if (res_ctrl == NULL) {
+			dev_err(dev, "can't get CTRL base address\n");
+			return -EINVAL;
+		}
+		res_xhciec = platform_get_resource(pdev, IORESOURCE_MEM, 1);
 	}
-	priv->ini.ctrl_regs = devm_ioremap_resource(dev, res);
+	priv->ini.ctrl_regs = devm_ioremap_resource(dev, res_ctrl);
 	if (IS_ERR(priv->ini.ctrl_regs)) {
 		dev_err(dev, "can't map CTRL register space\n");
 		return -EINVAL;
 	}
-
-	/* The XHCI EC registers are optional */
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	if (res) {
+	if (res_xhciec) {
 		priv->ini.xhci_ec_regs =
-			devm_ioremap_resource(dev, res);
+			devm_ioremap_resource(dev, res_xhciec);
 		if (IS_ERR(priv->ini.xhci_ec_regs)) {
 			dev_err(dev, "can't map XHCI EC register space\n");
 			return -EINVAL;
 		}
 	}
+	if (res_xhcigbl) {
+		priv->ini.xhci_gbl_regs =
+			devm_ioremap_resource(dev, res_xhcigbl);
+		if (IS_ERR(priv->ini.xhci_gbl_regs)) {
+			dev_err(dev, "can't map XHCI Global register space\n");
+			return -EINVAL;
+		}
+	}
 
 	of_property_read_u32(dn, "brcm,ipp", &priv->ini.ipp);
 	of_property_read_u32(dn, "brcm,ioc", &priv->ini.ioc);
@@ -480,11 +521,6 @@ static const struct dev_pm_ops brcm_usb_phy_pm_ops = {
 	SET_LATE_SYSTEM_SLEEP_PM_OPS(brcm_usb_phy_suspend, brcm_usb_phy_resume)
 };
 
-static const struct of_device_id brcm_usb_dt_ids[] = {
-	{ .compatible = "brcm,brcmstb-usb-phy" },
-	{ /* sentinel */ }
-};
-
 MODULE_DEVICE_TABLE(of, brcm_usb_dt_ids);
 
 static struct platform_driver brcm_usb_driver = {
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 07/13] phy: usb: Add support for new Synopsis USB controller on the 7216

[Kishon Vijay Abraham I]

Hi,

On 10/12/19 6:51 PM, Al Cooper wrote:
> The 7216 has the new USB XHCI controller from Synopsis. While
> this new controller and the PHY are similar to the STB versions,
> the major differences are:
> 
> - Many of the registers and fields in the CTRL block have been
>   removed or changed.
> - A new set of Synopsis control registers, BCHP_USB_XHCI_GBL, were
>   added.

Is it not Synopsys?

Thanks
Kishon

> - MDIO functionality has been replaced with direct access registers
>   in the BCHP_USB_XHCI_GBL block.
> - Power up PHY defaults that had to be changed by MDIO in previous
>   chips will now power up with the correct defaults.
> 
> A new init module was created for this new Synopsis USB controller.
> A new compatible string was added and the driver will dispatch
> into one of two init modules based on it. A "reg-names" field was
> added so the driver can more easily get optional registers.
> A DT bindings document was also added for this driver.
> 
> Signed-off-by: Al Cooper <alcooperx@gmail.com>
> ---
>  drivers/phy/broadcom/Makefile                 |   2 +-
>  .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 171 ++++++++++++++++++
>  drivers/phy/broadcom/phy-brcm-usb-init.h      |   2 +
>  drivers/phy/broadcom/phy-brcm-usb.c           |  70 +++++--
>  4 files changed, 227 insertions(+), 18 deletions(-)
>  create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> 
> diff --git a/drivers/phy/broadcom/Makefile b/drivers/phy/broadcom/Makefile
> index f453c7d3ffff..88523e2be861 100644
> --- a/drivers/phy/broadcom/Makefile
> +++ b/drivers/phy/broadcom/Makefile
> @@ -8,7 +8,7 @@ obj-$(CONFIG_PHY_NS2_USB_DRD)		+= phy-bcm-ns2-usbdrd.o
>  obj-$(CONFIG_PHY_BRCM_SATA)		+= phy-brcm-sata.o
>  obj-$(CONFIG_PHY_BRCM_USB)		+= phy-brcm-usb-dvr.o
>  
> -phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o
> +phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o phy-brcm-usb-init-synopsis.o
>  
>  obj-$(CONFIG_PHY_BCM_SR_PCIE)		+= phy-bcm-sr-pcie.o
>  obj-$(CONFIG_PHY_BCM_SR_USB)		+= phy-bcm-sr-usb.o
> diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> new file mode 100644
> index 000000000000..57663492b228
> --- /dev/null
> +++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> @@ -0,0 +1,171 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/* Copyright (c) 2018, Broadcom */
> +
> +/*
> + * This module contains USB PHY initialization for power up and S3 resume
> + * for newer Synopsis based USB hardware first used on the bcm7216.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +
> +#include <linux/soc/brcmstb/brcmstb.h>
> +#include "phy-brcm-usb-init.h"
> +
> +/* Register definitions for the USB CTRL block */
> +#define USB_CTRL_SETUP			0x00
> +#define   USB_CTRL_SETUP_STRAP_IPP_SEL_MASK		0x02000000
> +#define   USB_CTRL_SETUP_SCB2_EN_MASK			0x00008000
> +#define   USB_CTRL_SETUP_SCB1_EN_MASK			0x00004000
> +#define   USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK		0x00000200
> +#define   USB_CTRL_SETUP_IPP_MASK			0x00000020
> +#define   USB_CTRL_SETUP_IOC_MASK			0x00000010
> +#define USB_CTRL_USB_PM			0x04
> +#define   USB_CTRL_USB_PM_USB_PWRDN_MASK		0x80000000
> +#define   USB_CTRL_USB_PM_SOFT_RESET_MASK		0x40000000
> +#define   USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK		0x00800000
> +#define   USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK		0x00400000
> +#define USB_CTRL_USB_PM_STATUS		0x08
> +#define USB_CTRL_USB_DEVICE_CTL1	0x10
> +#define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK	0x00000003
> +
> +
> +static void xhci_soft_reset(struct brcm_usb_init_params *params,
> +			int on_off)
> +{
> +	void __iomem *ctrl = params->ctrl_regs;
> +
> +	/* Assert reset */
> +	if (on_off)
> +		USB_CTRL_UNSET(ctrl, USB_PM, XHC_SOFT_RESETB);
> +	/* De-assert reset */
> +	else
> +		USB_CTRL_SET(ctrl, USB_PM, XHC_SOFT_RESETB);
> +}
> +
> +static void usb_init_ipp(struct brcm_usb_init_params *params)
> +{
> +	void __iomem *ctrl = params->ctrl_regs;
> +	u32 reg;
> +	u32 orig_reg;
> +
> +	pr_debug("%s\n", __func__);
> +
> +	orig_reg = reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
> +	if (params->ipp != 2)
> +		/* override ipp strap pin (if it exits) */
> +		reg &= ~(USB_CTRL_MASK(SETUP, STRAP_IPP_SEL));
> +
> +	/* Override the default OC and PP polarity */
> +	reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
> +	if (params->ioc)
> +		reg |= USB_CTRL_MASK(SETUP, IOC);
> +	if (params->ipp == 1)
> +		reg |= USB_CTRL_MASK(SETUP, IPP);
> +	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
> +
> +	/*
> +	 * If we're changing IPP, make sure power is off long enough
> +	 * to turn off any connected devices.
> +	 */
> +	if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
> +		msleep(50);
> +}
> +
> +static void usb_init_common(struct brcm_usb_init_params *params)
> +{
> +	u32 reg;
> +	void __iomem *ctrl = params->ctrl_regs;
> +
> +	pr_debug("%s\n", __func__);
> +
> +	USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
> +	/* 1 millisecond - for USB clocks to settle down */
> +	usleep_range(1000, 2000);
> +
> +	if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
> +		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> +		reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> +		reg |= params->mode;
> +		brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> +	}
> +	switch (params->mode) {
> +	case USB_CTLR_MODE_HOST:
> +		USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
> +		break;
> +	default:
> +		USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
> +		USB_CTRL_SET(ctrl, USB_PM, BDC_SOFT_RESETB);
> +		break;
> +	}
> +}
> +
> +static void usb_init_xhci(struct brcm_usb_init_params *params)
> +{
> +	pr_debug("%s\n", __func__);
> +
> +	xhci_soft_reset(params, 0);
> +}
> +
> +static void usb_uninit_common(struct brcm_usb_init_params *params)
> +{
> +	void __iomem *ctrl = params->ctrl_regs;
> +
> +	pr_debug("%s\n", __func__);
> +
> +	USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
> +
> +}
> +
> +static void usb_uninit_xhci(struct brcm_usb_init_params *params)
> +{
> +
> +	pr_debug("%s\n", __func__);
> +
> +	xhci_soft_reset(params, 1);
> +}
> +
> +static int usb_get_dual_select(struct brcm_usb_init_params *params)
> +{
> +	void __iomem *ctrl = params->ctrl_regs;
> +	u32 reg = 0;
> +
> +	pr_debug("%s\n", __func__);
> +
> +	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> +	reg &= USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> +	return reg;
> +}
> +
> +static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
> +{
> +	void __iomem *ctrl = params->ctrl_regs;
> +	u32 reg;
> +
> +	pr_debug("%s\n", __func__);
> +
> +	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> +	reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> +	reg |= mode;
> +	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> +}
> +
> +
> +static const struct brcm_usb_init_ops bcm7216_ops = {
> +	.init_ipp = usb_init_ipp,
> +	.init_common = usb_init_common,
> +	.init_xhci = usb_init_xhci,
> +	.uninit_common = usb_uninit_common,
> +	.uninit_xhci = usb_uninit_xhci,
> +	.get_dual_select = usb_get_dual_select,
> +	.set_dual_select = usb_set_dual_select,
> +};
> +
> +void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
> +{
> +
> +	pr_debug("%s\n", __func__);
> +
> +	params->family_name = "7216";
> +	params->ops = &bcm7216_ops;
> +}
> diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
> index 7701872d1136..db6851c55335 100644
> --- a/drivers/phy/broadcom/phy-brcm-usb-init.h
> +++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
> @@ -43,6 +43,7 @@ struct brcm_usb_init_ops {
>  struct  brcm_usb_init_params {
>  	void __iomem *ctrl_regs;
>  	void __iomem *xhci_ec_regs;
> +	void __iomem *xhci_gbl_regs;
>  	int ioc;
>  	int ipp;
>  	int mode;
> @@ -55,6 +56,7 @@ struct  brcm_usb_init_params {
>  };
>  
>  void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
> +void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
>  
>  static inline u32 brcm_usb_readl(void __iomem *addr)
>  {
> diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
> index 9d93c5599511..64379ede480e 100644
> --- a/drivers/phy/broadcom/phy-brcm-usb.c
> +++ b/drivers/phy/broadcom/phy-brcm-usb.c
> @@ -241,6 +241,15 @@ static const struct attribute_group brcm_usb_phy_group = {
>  	.attrs = brcm_usb_phy_attrs,
>  };
>  
> +static const struct of_device_id brcm_usb_dt_ids[] = {
> +	{
> +		.compatible = "brcm,bcm7216-usb-phy",
> +		.data = &brcm_usb_dvr_init_7216,
> +	},
> +	{ .compatible = "brcm,brcmstb-usb-phy" },
> +	{ /* sentinel */ }
> +};
> +
>  static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
>  				 struct brcm_usb_phy_data *priv,
>  				 struct device_node *dn)
> @@ -316,13 +325,16 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
>  
>  static int brcm_usb_phy_probe(struct platform_device *pdev)
>  {
> -	struct resource *res;
> +	struct resource *res_ctrl;
> +	struct resource *res_xhciec = NULL;
> +	struct resource *res_xhcigbl = NULL;
>  	struct device *dev = &pdev->dev;
>  	struct brcm_usb_phy_data *priv;
>  	struct phy_provider *phy_provider;
>  	struct device_node *dn = pdev->dev.of_node;
>  	int err;
>  	const char *mode;
> +	const struct of_device_id *match;
>  
>  	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
>  	if (!priv)
> @@ -331,30 +343,59 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
>  
>  	priv->ini.family_id = brcmstb_get_family_id();
>  	priv->ini.product_id = brcmstb_get_product_id();
> -	brcm_usb_dvr_init_7445(&priv->ini);
> +
> +	match = of_match_node(brcm_usb_dt_ids, dev->of_node);
> +	if (match && match->data) {
> +		void (*dvr_init)(struct brcm_usb_init_params *params);
> +
> +		dvr_init = match->data;
> +		(*dvr_init)(&priv->ini);
> +	} else {
> +		brcm_usb_dvr_init_7445(&priv->ini);
> +	}
> +
>  	dev_dbg(dev, "Best mapping table is for %s\n",
>  		priv->ini.family_name);
> -	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> -	if (!res) {
> -		dev_err(dev, "can't get USB_CTRL base address\n");
> -		return -EINVAL;
> +
> +	/* Newer DT node has reg-names. xhci_ec and xhci_gbl are optional. */
> +	res_ctrl = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
> +	if (res_ctrl != NULL) {
> +		res_xhciec = platform_get_resource_byname(pdev,
> +							  IORESOURCE_MEM,
> +							  "xhci_ec");
> +		res_xhcigbl = platform_get_resource_byname(pdev,
> +							   IORESOURCE_MEM,
> +							   "xhci_gbl");
> +	} else {
> +		/* Older DT node without reg-names, use index */
> +		res_ctrl = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +		if (res_ctrl == NULL) {
> +			dev_err(dev, "can't get CTRL base address\n");
> +			return -EINVAL;
> +		}
> +		res_xhciec = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>  	}
> -	priv->ini.ctrl_regs = devm_ioremap_resource(dev, res);
> +	priv->ini.ctrl_regs = devm_ioremap_resource(dev, res_ctrl);
>  	if (IS_ERR(priv->ini.ctrl_regs)) {
>  		dev_err(dev, "can't map CTRL register space\n");
>  		return -EINVAL;
>  	}
> -
> -	/* The XHCI EC registers are optional */
> -	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> -	if (res) {
> +	if (res_xhciec) {
>  		priv->ini.xhci_ec_regs =
> -			devm_ioremap_resource(dev, res);
> +			devm_ioremap_resource(dev, res_xhciec);
>  		if (IS_ERR(priv->ini.xhci_ec_regs)) {
>  			dev_err(dev, "can't map XHCI EC register space\n");
>  			return -EINVAL;
>  		}
>  	}
> +	if (res_xhcigbl) {
> +		priv->ini.xhci_gbl_regs =
> +			devm_ioremap_resource(dev, res_xhcigbl);
> +		if (IS_ERR(priv->ini.xhci_gbl_regs)) {
> +			dev_err(dev, "can't map XHCI Global register space\n");
> +			return -EINVAL;
> +		}
> +	}
>  
>  	of_property_read_u32(dn, "brcm,ipp", &priv->ini.ipp);
>  	of_property_read_u32(dn, "brcm,ioc", &priv->ini.ioc);
> @@ -480,11 +521,6 @@ static const struct dev_pm_ops brcm_usb_phy_pm_ops = {
>  	SET_LATE_SYSTEM_SLEEP_PM_OPS(brcm_usb_phy_suspend, brcm_usb_phy_resume)
>  };
>  
> -static const struct of_device_id brcm_usb_dt_ids[] = {
> -	{ .compatible = "brcm,brcmstb-usb-phy" },
> -	{ /* sentinel */ }
> -};
> -
>  MODULE_DEVICE_TABLE(of, brcm_usb_dt_ids);
>  
>  static struct platform_driver brcm_usb_driver = {
> 

Re: [PATCH v3 07/13] phy: usb: Add support for new Synopsis USB controller on the 7216

[Kishon Vijay Abraham I]

Hi,

On 10/12/19 6:51 PM, Al Cooper wrote:
> The 7216 has the new USB XHCI controller from Synopsis. While
> this new controller and the PHY are similar to the STB versions,
> the major differences are:
> 
> - Many of the registers and fields in the CTRL block have been
>   removed or changed.
> - A new set of Synopsis control registers, BCHP_USB_XHCI_GBL, were
>   added.

Is it not Synopsys?

Thanks
Kishon

> - MDIO functionality has been replaced with direct access registers
>   in the BCHP_USB_XHCI_GBL block.
> - Power up PHY defaults that had to be changed by MDIO in previous
>   chips will now power up with the correct defaults.
> 
> A new init module was created for this new Synopsis USB controller.
> A new compatible string was added and the driver will dispatch
> into one of two init modules based on it. A "reg-names" field was
> added so the driver can more easily get optional registers.
> A DT bindings document was also added for this driver.
> 
> Signed-off-by: Al Cooper <alcooperx@gmail.com>
> ---
>  drivers/phy/broadcom/Makefile                 |   2 +-
>  .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 171 ++++++++++++++++++
>  drivers/phy/broadcom/phy-brcm-usb-init.h      |   2 +
>  drivers/phy/broadcom/phy-brcm-usb.c           |  70 +++++--
>  4 files changed, 227 insertions(+), 18 deletions(-)
>  create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> 
> diff --git a/drivers/phy/broadcom/Makefile b/drivers/phy/broadcom/Makefile
> index f453c7d3ffff..88523e2be861 100644
> --- a/drivers/phy/broadcom/Makefile
> +++ b/drivers/phy/broadcom/Makefile
> @@ -8,7 +8,7 @@ obj-$(CONFIG_PHY_NS2_USB_DRD)		+= phy-bcm-ns2-usbdrd.o
>  obj-$(CONFIG_PHY_BRCM_SATA)		+= phy-brcm-sata.o
>  obj-$(CONFIG_PHY_BRCM_USB)		+= phy-brcm-usb-dvr.o
>  
> -phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o
> +phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o phy-brcm-usb-init-synopsis.o
>  
>  obj-$(CONFIG_PHY_BCM_SR_PCIE)		+= phy-bcm-sr-pcie.o
>  obj-$(CONFIG_PHY_BCM_SR_USB)		+= phy-bcm-sr-usb.o
> diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> new file mode 100644
> index 000000000000..57663492b228
> --- /dev/null
> +++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> @@ -0,0 +1,171 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/* Copyright (c) 2018, Broadcom */
> +
> +/*
> + * This module contains USB PHY initialization for power up and S3 resume
> + * for newer Synopsis based USB hardware first used on the bcm7216.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +
> +#include <linux/soc/brcmstb/brcmstb.h>
> +#include "phy-brcm-usb-init.h"
> +
> +/* Register definitions for the USB CTRL block */
> +#define USB_CTRL_SETUP			0x00
> +#define   USB_CTRL_SETUP_STRAP_IPP_SEL_MASK		0x02000000
> +#define   USB_CTRL_SETUP_SCB2_EN_MASK			0x00008000
> +#define   USB_CTRL_SETUP_SCB1_EN_MASK			0x00004000
> +#define   USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK		0x00000200
> +#define   USB_CTRL_SETUP_IPP_MASK			0x00000020
> +#define   USB_CTRL_SETUP_IOC_MASK			0x00000010
> +#define USB_CTRL_USB_PM			0x04
> +#define   USB_CTRL_USB_PM_USB_PWRDN_MASK		0x80000000
> +#define   USB_CTRL_USB_PM_SOFT_RESET_MASK		0x40000000
> +#define   USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK		0x00800000
> +#define   USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK		0x00400000
> +#define USB_CTRL_USB_PM_STATUS		0x08
> +#define USB_CTRL_USB_DEVICE_CTL1	0x10
> +#define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK	0x00000003
> +
> +
> +static void xhci_soft_reset(struct brcm_usb_init_params *params,
> +			int on_off)
> +{
> +	void __iomem *ctrl = params->ctrl_regs;
> +
> +	/* Assert reset */
> +	if (on_off)
> +		USB_CTRL_UNSET(ctrl, USB_PM, XHC_SOFT_RESETB);
> +	/* De-assert reset */
> +	else
> +		USB_CTRL_SET(ctrl, USB_PM, XHC_SOFT_RESETB);
> +}
> +
> +static void usb_init_ipp(struct brcm_usb_init_params *params)
> +{
> +	void __iomem *ctrl = params->ctrl_regs;
> +	u32 reg;
> +	u32 orig_reg;
> +
> +	pr_debug("%s\n", __func__);
> +
> +	orig_reg = reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
> +	if (params->ipp != 2)
> +		/* override ipp strap pin (if it exits) */
> +		reg &= ~(USB_CTRL_MASK(SETUP, STRAP_IPP_SEL));
> +
> +	/* Override the default OC and PP polarity */
> +	reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
> +	if (params->ioc)
> +		reg |= USB_CTRL_MASK(SETUP, IOC);
> +	if (params->ipp == 1)
> +		reg |= USB_CTRL_MASK(SETUP, IPP);
> +	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
> +
> +	/*
> +	 * If we're changing IPP, make sure power is off long enough
> +	 * to turn off any connected devices.
> +	 */
> +	if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
> +		msleep(50);
> +}
> +
> +static void usb_init_common(struct brcm_usb_init_params *params)
> +{
> +	u32 reg;
> +	void __iomem *ctrl = params->ctrl_regs;
> +
> +	pr_debug("%s\n", __func__);
> +
> +	USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
> +	/* 1 millisecond - for USB clocks to settle down */
> +	usleep_range(1000, 2000);
> +
> +	if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
> +		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> +		reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> +		reg |= params->mode;
> +		brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> +	}
> +	switch (params->mode) {
> +	case USB_CTLR_MODE_HOST:
> +		USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
> +		break;
> +	default:
> +		USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
> +		USB_CTRL_SET(ctrl, USB_PM, BDC_SOFT_RESETB);
> +		break;
> +	}
> +}
> +
> +static void usb_init_xhci(struct brcm_usb_init_params *params)
> +{
> +	pr_debug("%s\n", __func__);
> +
> +	xhci_soft_reset(params, 0);
> +}
> +
> +static void usb_uninit_common(struct brcm_usb_init_params *params)
> +{
> +	void __iomem *ctrl = params->ctrl_regs;
> +
> +	pr_debug("%s\n", __func__);
> +
> +	USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
> +
> +}
> +
> +static void usb_uninit_xhci(struct brcm_usb_init_params *params)
> +{
> +
> +	pr_debug("%s\n", __func__);
> +
> +	xhci_soft_reset(params, 1);
> +}
> +
> +static int usb_get_dual_select(struct brcm_usb_init_params *params)
> +{
> +	void __iomem *ctrl = params->ctrl_regs;
> +	u32 reg = 0;
> +
> +	pr_debug("%s\n", __func__);
> +
> +	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> +	reg &= USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> +	return reg;
> +}
> +
> +static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
> +{
> +	void __iomem *ctrl = params->ctrl_regs;
> +	u32 reg;
> +
> +	pr_debug("%s\n", __func__);
> +
> +	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> +	reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> +	reg |= mode;
> +	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> +}
> +
> +
> +static const struct brcm_usb_init_ops bcm7216_ops = {
> +	.init_ipp = usb_init_ipp,
> +	.init_common = usb_init_common,
> +	.init_xhci = usb_init_xhci,
> +	.uninit_common = usb_uninit_common,
> +	.uninit_xhci = usb_uninit_xhci,
> +	.get_dual_select = usb_get_dual_select,
> +	.set_dual_select = usb_set_dual_select,
> +};
> +
> +void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
> +{
> +
> +	pr_debug("%s\n", __func__);
> +
> +	params->family_name = "7216";
> +	params->ops = &bcm7216_ops;
> +}
> diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
> index 7701872d1136..db6851c55335 100644
> --- a/drivers/phy/broadcom/phy-brcm-usb-init.h
> +++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
> @@ -43,6 +43,7 @@ struct brcm_usb_init_ops {
>  struct  brcm_usb_init_params {
>  	void __iomem *ctrl_regs;
>  	void __iomem *xhci_ec_regs;
> +	void __iomem *xhci_gbl_regs;
>  	int ioc;
>  	int ipp;
>  	int mode;
> @@ -55,6 +56,7 @@ struct  brcm_usb_init_params {
>  };
>  
>  void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
> +void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
>  
>  static inline u32 brcm_usb_readl(void __iomem *addr)
>  {
> diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
> index 9d93c5599511..64379ede480e 100644
> --- a/drivers/phy/broadcom/phy-brcm-usb.c
> +++ b/drivers/phy/broadcom/phy-brcm-usb.c
> @@ -241,6 +241,15 @@ static const struct attribute_group brcm_usb_phy_group = {
>  	.attrs = brcm_usb_phy_attrs,
>  };
>  
> +static const struct of_device_id brcm_usb_dt_ids[] = {
> +	{
> +		.compatible = "brcm,bcm7216-usb-phy",
> +		.data = &brcm_usb_dvr_init_7216,
> +	},
> +	{ .compatible = "brcm,brcmstb-usb-phy" },
> +	{ /* sentinel */ }
> +};
> +
>  static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
>  				 struct brcm_usb_phy_data *priv,
>  				 struct device_node *dn)
> @@ -316,13 +325,16 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
>  
>  static int brcm_usb_phy_probe(struct platform_device *pdev)
>  {
> -	struct resource *res;
> +	struct resource *res_ctrl;
> +	struct resource *res_xhciec = NULL;
> +	struct resource *res_xhcigbl = NULL;
>  	struct device *dev = &pdev->dev;
>  	struct brcm_usb_phy_data *priv;
>  	struct phy_provider *phy_provider;
>  	struct device_node *dn = pdev->dev.of_node;
>  	int err;
>  	const char *mode;
> +	const struct of_device_id *match;
>  
>  	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
>  	if (!priv)
> @@ -331,30 +343,59 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
>  
>  	priv->ini.family_id = brcmstb_get_family_id();
>  	priv->ini.product_id = brcmstb_get_product_id();
> -	brcm_usb_dvr_init_7445(&priv->ini);
> +
> +	match = of_match_node(brcm_usb_dt_ids, dev->of_node);
> +	if (match && match->data) {
> +		void (*dvr_init)(struct brcm_usb_init_params *params);
> +
> +		dvr_init = match->data;
> +		(*dvr_init)(&priv->ini);
> +	} else {
> +		brcm_usb_dvr_init_7445(&priv->ini);
> +	}
> +
>  	dev_dbg(dev, "Best mapping table is for %s\n",
>  		priv->ini.family_name);
> -	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> -	if (!res) {
> -		dev_err(dev, "can't get USB_CTRL base address\n");
> -		return -EINVAL;
> +
> +	/* Newer DT node has reg-names. xhci_ec and xhci_gbl are optional. */
> +	res_ctrl = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
> +	if (res_ctrl != NULL) {
> +		res_xhciec = platform_get_resource_byname(pdev,
> +							  IORESOURCE_MEM,
> +							  "xhci_ec");
> +		res_xhcigbl = platform_get_resource_byname(pdev,
> +							   IORESOURCE_MEM,
> +							   "xhci_gbl");
> +	} else {
> +		/* Older DT node without reg-names, use index */
> +		res_ctrl = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +		if (res_ctrl == NULL) {
> +			dev_err(dev, "can't get CTRL base address\n");
> +			return -EINVAL;
> +		}
> +		res_xhciec = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>  	}
> -	priv->ini.ctrl_regs = devm_ioremap_resource(dev, res);
> +	priv->ini.ctrl_regs = devm_ioremap_resource(dev, res_ctrl);
>  	if (IS_ERR(priv->ini.ctrl_regs)) {
>  		dev_err(dev, "can't map CTRL register space\n");
>  		return -EINVAL;
>  	}
> -
> -	/* The XHCI EC registers are optional */
> -	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> -	if (res) {
> +	if (res_xhciec) {
>  		priv->ini.xhci_ec_regs =
> -			devm_ioremap_resource(dev, res);
> +			devm_ioremap_resource(dev, res_xhciec);
>  		if (IS_ERR(priv->ini.xhci_ec_regs)) {
>  			dev_err(dev, "can't map XHCI EC register space\n");
>  			return -EINVAL;
>  		}
>  	}
> +	if (res_xhcigbl) {
> +		priv->ini.xhci_gbl_regs =
> +			devm_ioremap_resource(dev, res_xhcigbl);
> +		if (IS_ERR(priv->ini.xhci_gbl_regs)) {
> +			dev_err(dev, "can't map XHCI Global register space\n");
> +			return -EINVAL;
> +		}
> +	}
>  
>  	of_property_read_u32(dn, "brcm,ipp", &priv->ini.ipp);
>  	of_property_read_u32(dn, "brcm,ioc", &priv->ini.ioc);
> @@ -480,11 +521,6 @@ static const struct dev_pm_ops brcm_usb_phy_pm_ops = {
>  	SET_LATE_SYSTEM_SLEEP_PM_OPS(brcm_usb_phy_suspend, brcm_usb_phy_resume)
>  };
>  
> -static const struct of_device_id brcm_usb_dt_ids[] = {
> -	{ .compatible = "brcm,brcmstb-usb-phy" },
> -	{ /* sentinel */ }
> -};
> -
>  MODULE_DEVICE_TABLE(of, brcm_usb_dt_ids);
>  
>  static struct platform_driver brcm_usb_driver = {
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 07/13] phy: usb: Add support for new Synopsis USB controller on the 7216

[Alan Cooper]

On Fri, Jan 3, 2020 at 4:31 AM Kishon Vijay Abraham I <kishon@ti.com> wrote:
>
> Hi,
>
> On 10/12/19 6:51 PM, Al Cooper wrote:
> > The 7216 has the new USB XHCI controller from Synopsis. While
> > this new controller and the PHY are similar to the STB versions,
> > the major differences are:
> >
> > - Many of the registers and fields in the CTRL block have been
> >   removed or changed.
> > - A new set of Synopsis control registers, BCHP_USB_XHCI_GBL, were
> >   added.
>
> Is it not Synopsys?

Yes, I'll send a v4 of patches 7 and 8


On Fri, Jan 3, 2020 at 4:31 AM Kishon Vijay Abraham I <kishon@ti.com> wrote:
>
> Hi,
>
> On 10/12/19 6:51 PM, Al Cooper wrote:
> > The 7216 has the new USB XHCI controller from Synopsis. While
> > this new controller and the PHY are similar to the STB versions,
> > the major differences are:
> >
> > - Many of the registers and fields in the CTRL block have been
> >   removed or changed.
> > - A new set of Synopsis control registers, BCHP_USB_XHCI_GBL, were
> >   added.
>
> Is it not Synopsys?
>
> Thanks
> Kishon
>
> > - MDIO functionality has been replaced with direct access registers
> >   in the BCHP_USB_XHCI_GBL block.
> > - Power up PHY defaults that had to be changed by MDIO in previous
> >   chips will now power up with the correct defaults.
> >
> > A new init module was created for this new Synopsis USB controller.
> > A new compatible string was added and the driver will dispatch
> > into one of two init modules based on it. A "reg-names" field was
> > added so the driver can more easily get optional registers.
> > A DT bindings document was also added for this driver.
> >
> > Signed-off-by: Al Cooper <alcooperx@gmail.com>
> > ---
> >  drivers/phy/broadcom/Makefile                 |   2 +-
> >  .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 171 ++++++++++++++++++
> >  drivers/phy/broadcom/phy-brcm-usb-init.h      |   2 +
> >  drivers/phy/broadcom/phy-brcm-usb.c           |  70 +++++--
> >  4 files changed, 227 insertions(+), 18 deletions(-)
> >  create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> >
> > diff --git a/drivers/phy/broadcom/Makefile b/drivers/phy/broadcom/Makefile
> > index f453c7d3ffff..88523e2be861 100644
> > --- a/drivers/phy/broadcom/Makefile
> > +++ b/drivers/phy/broadcom/Makefile
> > @@ -8,7 +8,7 @@ obj-$(CONFIG_PHY_NS2_USB_DRD)         += phy-bcm-ns2-usbdrd.o
> >  obj-$(CONFIG_PHY_BRCM_SATA)          += phy-brcm-sata.o
> >  obj-$(CONFIG_PHY_BRCM_USB)           += phy-brcm-usb-dvr.o
> >
> > -phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o
> > +phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o phy-brcm-usb-init-synopsis.o
> >
> >  obj-$(CONFIG_PHY_BCM_SR_PCIE)                += phy-bcm-sr-pcie.o
> >  obj-$(CONFIG_PHY_BCM_SR_USB)         += phy-bcm-sr-usb.o
> > diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> > new file mode 100644
> > index 000000000000..57663492b228
> > --- /dev/null
> > +++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> > @@ -0,0 +1,171 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/* Copyright (c) 2018, Broadcom */
> > +
> > +/*
> > + * This module contains USB PHY initialization for power up and S3 resume
> > + * for newer Synopsis based USB hardware first used on the bcm7216.
> > + */
> > +
> > +#include <linux/delay.h>
> > +#include <linux/io.h>
> > +
> > +#include <linux/soc/brcmstb/brcmstb.h>
> > +#include "phy-brcm-usb-init.h"
> > +
> > +/* Register definitions for the USB CTRL block */
> > +#define USB_CTRL_SETUP                       0x00
> > +#define   USB_CTRL_SETUP_STRAP_IPP_SEL_MASK          0x02000000
> > +#define   USB_CTRL_SETUP_SCB2_EN_MASK                        0x00008000
> > +#define   USB_CTRL_SETUP_SCB1_EN_MASK                        0x00004000
> > +#define   USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK          0x00000200
> > +#define   USB_CTRL_SETUP_IPP_MASK                    0x00000020
> > +#define   USB_CTRL_SETUP_IOC_MASK                    0x00000010
> > +#define USB_CTRL_USB_PM                      0x04
> > +#define   USB_CTRL_USB_PM_USB_PWRDN_MASK             0x80000000
> > +#define   USB_CTRL_USB_PM_SOFT_RESET_MASK            0x40000000
> > +#define   USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK               0x00800000
> > +#define   USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK               0x00400000
> > +#define USB_CTRL_USB_PM_STATUS               0x08
> > +#define USB_CTRL_USB_DEVICE_CTL1     0x10
> > +#define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK    0x00000003
> > +
> > +
> > +static void xhci_soft_reset(struct brcm_usb_init_params *params,
> > +                     int on_off)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +
> > +     /* Assert reset */
> > +     if (on_off)
> > +             USB_CTRL_UNSET(ctrl, USB_PM, XHC_SOFT_RESETB);
> > +     /* De-assert reset */
> > +     else
> > +             USB_CTRL_SET(ctrl, USB_PM, XHC_SOFT_RESETB);
> > +}
> > +
> > +static void usb_init_ipp(struct brcm_usb_init_params *params)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +     u32 reg;
> > +     u32 orig_reg;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     orig_reg = reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
> > +     if (params->ipp != 2)
> > +             /* override ipp strap pin (if it exits) */
> > +             reg &= ~(USB_CTRL_MASK(SETUP, STRAP_IPP_SEL));
> > +
> > +     /* Override the default OC and PP polarity */
> > +     reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
> > +     if (params->ioc)
> > +             reg |= USB_CTRL_MASK(SETUP, IOC);
> > +     if (params->ipp == 1)
> > +             reg |= USB_CTRL_MASK(SETUP, IPP);
> > +     brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
> > +
> > +     /*
> > +      * If we're changing IPP, make sure power is off long enough
> > +      * to turn off any connected devices.
> > +      */
> > +     if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
> > +             msleep(50);
> > +}
> > +
> > +static void usb_init_common(struct brcm_usb_init_params *params)
> > +{
> > +     u32 reg;
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
> > +     /* 1 millisecond - for USB clocks to settle down */
> > +     usleep_range(1000, 2000);
> > +
> > +     if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
> > +             reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +             reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> > +             reg |= params->mode;
> > +             brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +     }
> > +     switch (params->mode) {
> > +     case USB_CTLR_MODE_HOST:
> > +             USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
> > +             break;
> > +     default:
> > +             USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
> > +             USB_CTRL_SET(ctrl, USB_PM, BDC_SOFT_RESETB);
> > +             break;
> > +     }
> > +}
> > +
> > +static void usb_init_xhci(struct brcm_usb_init_params *params)
> > +{
> > +     pr_debug("%s\n", __func__);
> > +
> > +     xhci_soft_reset(params, 0);
> > +}
> > +
> > +static void usb_uninit_common(struct brcm_usb_init_params *params)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
> > +
> > +}
> > +
> > +static void usb_uninit_xhci(struct brcm_usb_init_params *params)
> > +{
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     xhci_soft_reset(params, 1);
> > +}
> > +
> > +static int usb_get_dual_select(struct brcm_usb_init_params *params)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +     u32 reg = 0;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +     reg &= USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> > +     return reg;
> > +}
> > +
> > +static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +     u32 reg;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +     reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> > +     reg |= mode;
> > +     brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +}
> > +
> > +
> > +static const struct brcm_usb_init_ops bcm7216_ops = {
> > +     .init_ipp = usb_init_ipp,
> > +     .init_common = usb_init_common,
> > +     .init_xhci = usb_init_xhci,
> > +     .uninit_common = usb_uninit_common,
> > +     .uninit_xhci = usb_uninit_xhci,
> > +     .get_dual_select = usb_get_dual_select,
> > +     .set_dual_select = usb_set_dual_select,
> > +};
> > +
> > +void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
> > +{
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     params->family_name = "7216";
> > +     params->ops = &bcm7216_ops;
> > +}
> > diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
> > index 7701872d1136..db6851c55335 100644
> > --- a/drivers/phy/broadcom/phy-brcm-usb-init.h
> > +++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
> > @@ -43,6 +43,7 @@ struct brcm_usb_init_ops {
> >  struct  brcm_usb_init_params {
> >       void __iomem *ctrl_regs;
> >       void __iomem *xhci_ec_regs;
> > +     void __iomem *xhci_gbl_regs;
> >       int ioc;
> >       int ipp;
> >       int mode;
> > @@ -55,6 +56,7 @@ struct  brcm_usb_init_params {
> >  };
> >
> >  void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
> > +void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
> >
> >  static inline u32 brcm_usb_readl(void __iomem *addr)
> >  {
> > diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
> > index 9d93c5599511..64379ede480e 100644
> > --- a/drivers/phy/broadcom/phy-brcm-usb.c
> > +++ b/drivers/phy/broadcom/phy-brcm-usb.c
> > @@ -241,6 +241,15 @@ static const struct attribute_group brcm_usb_phy_group = {
> >       .attrs = brcm_usb_phy_attrs,
> >  };
> >
> > +static const struct of_device_id brcm_usb_dt_ids[] = {
> > +     {
> > +             .compatible = "brcm,bcm7216-usb-phy",
> > +             .data = &brcm_usb_dvr_init_7216,
> > +     },
> > +     { .compatible = "brcm,brcmstb-usb-phy" },
> > +     { /* sentinel */ }
> > +};
> > +
> >  static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
> >                                struct brcm_usb_phy_data *priv,
> >                                struct device_node *dn)
> > @@ -316,13 +325,16 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
> >
> >  static int brcm_usb_phy_probe(struct platform_device *pdev)
> >  {
> > -     struct resource *res;
> > +     struct resource *res_ctrl;
> > +     struct resource *res_xhciec = NULL;
> > +     struct resource *res_xhcigbl = NULL;
> >       struct device *dev = &pdev->dev;
> >       struct brcm_usb_phy_data *priv;
> >       struct phy_provider *phy_provider;
> >       struct device_node *dn = pdev->dev.of_node;
> >       int err;
> >       const char *mode;
> > +     const struct of_device_id *match;
> >
> >       priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> >       if (!priv)
> > @@ -331,30 +343,59 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
> >
> >       priv->ini.family_id = brcmstb_get_family_id();
> >       priv->ini.product_id = brcmstb_get_product_id();
> > -     brcm_usb_dvr_init_7445(&priv->ini);
> > +
> > +     match = of_match_node(brcm_usb_dt_ids, dev->of_node);
> > +     if (match && match->data) {
> > +             void (*dvr_init)(struct brcm_usb_init_params *params);
> > +
> > +             dvr_init = match->data;
> > +             (*dvr_init)(&priv->ini);
> > +     } else {
> > +             brcm_usb_dvr_init_7445(&priv->ini);
> > +     }
> > +
> >       dev_dbg(dev, "Best mapping table is for %s\n",
> >               priv->ini.family_name);
> > -     res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > -     if (!res) {
> > -             dev_err(dev, "can't get USB_CTRL base address\n");
> > -             return -EINVAL;
> > +
> > +     /* Newer DT node has reg-names. xhci_ec and xhci_gbl are optional. */
> > +     res_ctrl = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
> > +     if (res_ctrl != NULL) {
> > +             res_xhciec = platform_get_resource_byname(pdev,
> > +                                                       IORESOURCE_MEM,
> > +                                                       "xhci_ec");
> > +             res_xhcigbl = platform_get_resource_byname(pdev,
> > +                                                        IORESOURCE_MEM,
> > +                                                        "xhci_gbl");
> > +     } else {
> > +             /* Older DT node without reg-names, use index */
> > +             res_ctrl = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > +             if (res_ctrl == NULL) {
> > +                     dev_err(dev, "can't get CTRL base address\n");
> > +                     return -EINVAL;
> > +             }
> > +             res_xhciec = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> >       }
> > -     priv->ini.ctrl_regs = devm_ioremap_resource(dev, res);
> > +     priv->ini.ctrl_regs = devm_ioremap_resource(dev, res_ctrl);
> >       if (IS_ERR(priv->ini.ctrl_regs)) {
> >               dev_err(dev, "can't map CTRL register space\n");
> >               return -EINVAL;
> >       }
> > -
> > -     /* The XHCI EC registers are optional */
> > -     res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> > -     if (res) {
> > +     if (res_xhciec) {
> >               priv->ini.xhci_ec_regs =
> > -                     devm_ioremap_resource(dev, res);
> > +                     devm_ioremap_resource(dev, res_xhciec);
> >               if (IS_ERR(priv->ini.xhci_ec_regs)) {
> >                       dev_err(dev, "can't map XHCI EC register space\n");
> >                       return -EINVAL;
> >               }
> >       }
> > +     if (res_xhcigbl) {
> > +             priv->ini.xhci_gbl_regs =
> > +                     devm_ioremap_resource(dev, res_xhcigbl);
> > +             if (IS_ERR(priv->ini.xhci_gbl_regs)) {
> > +                     dev_err(dev, "can't map XHCI Global register space\n");
> > +                     return -EINVAL;
> > +             }
> > +     }
> >
> >       of_property_read_u32(dn, "brcm,ipp", &priv->ini.ipp);
> >       of_property_read_u32(dn, "brcm,ioc", &priv->ini.ioc);
> > @@ -480,11 +521,6 @@ static const struct dev_pm_ops brcm_usb_phy_pm_ops = {
> >       SET_LATE_SYSTEM_SLEEP_PM_OPS(brcm_usb_phy_suspend, brcm_usb_phy_resume)
> >  };
> >
> > -static const struct of_device_id brcm_usb_dt_ids[] = {
> > -     { .compatible = "brcm,brcmstb-usb-phy" },
> > -     { /* sentinel */ }
> > -};
> > -
> >  MODULE_DEVICE_TABLE(of, brcm_usb_dt_ids);
> >
> >  static struct platform_driver brcm_usb_driver = {
> >

Re: [PATCH v3 07/13] phy: usb: Add support for new Synopsis USB controller on the 7216

[Alan Cooper]

On Fri, Jan 3, 2020 at 4:31 AM Kishon Vijay Abraham I <kishon@ti.com> wrote:
>
> Hi,
>
> On 10/12/19 6:51 PM, Al Cooper wrote:
> > The 7216 has the new USB XHCI controller from Synopsis. While
> > this new controller and the PHY are similar to the STB versions,
> > the major differences are:
> >
> > - Many of the registers and fields in the CTRL block have been
> >   removed or changed.
> > - A new set of Synopsis control registers, BCHP_USB_XHCI_GBL, were
> >   added.
>
> Is it not Synopsys?

Yes, I'll send a v4 of patches 7 and 8


On Fri, Jan 3, 2020 at 4:31 AM Kishon Vijay Abraham I <kishon@ti.com> wrote:
>
> Hi,
>
> On 10/12/19 6:51 PM, Al Cooper wrote:
> > The 7216 has the new USB XHCI controller from Synopsis. While
> > this new controller and the PHY are similar to the STB versions,
> > the major differences are:
> >
> > - Many of the registers and fields in the CTRL block have been
> >   removed or changed.
> > - A new set of Synopsis control registers, BCHP_USB_XHCI_GBL, were
> >   added.
>
> Is it not Synopsys?
>
> Thanks
> Kishon
>
> > - MDIO functionality has been replaced with direct access registers
> >   in the BCHP_USB_XHCI_GBL block.
> > - Power up PHY defaults that had to be changed by MDIO in previous
> >   chips will now power up with the correct defaults.
> >
> > A new init module was created for this new Synopsis USB controller.
> > A new compatible string was added and the driver will dispatch
> > into one of two init modules based on it. A "reg-names" field was
> > added so the driver can more easily get optional registers.
> > A DT bindings document was also added for this driver.
> >
> > Signed-off-by: Al Cooper <alcooperx@gmail.com>
> > ---
> >  drivers/phy/broadcom/Makefile                 |   2 +-
> >  .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 171 ++++++++++++++++++
> >  drivers/phy/broadcom/phy-brcm-usb-init.h      |   2 +
> >  drivers/phy/broadcom/phy-brcm-usb.c           |  70 +++++--
> >  4 files changed, 227 insertions(+), 18 deletions(-)
> >  create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> >
> > diff --git a/drivers/phy/broadcom/Makefile b/drivers/phy/broadcom/Makefile
> > index f453c7d3ffff..88523e2be861 100644
> > --- a/drivers/phy/broadcom/Makefile
> > +++ b/drivers/phy/broadcom/Makefile
> > @@ -8,7 +8,7 @@ obj-$(CONFIG_PHY_NS2_USB_DRD)         += phy-bcm-ns2-usbdrd.o
> >  obj-$(CONFIG_PHY_BRCM_SATA)          += phy-brcm-sata.o
> >  obj-$(CONFIG_PHY_BRCM_USB)           += phy-brcm-usb-dvr.o
> >
> > -phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o
> > +phy-brcm-usb-dvr-objs := phy-brcm-usb.o phy-brcm-usb-init.o phy-brcm-usb-init-synopsis.o
> >
> >  obj-$(CONFIG_PHY_BCM_SR_PCIE)                += phy-bcm-sr-pcie.o
> >  obj-$(CONFIG_PHY_BCM_SR_USB)         += phy-bcm-sr-usb.o
> > diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> > new file mode 100644
> > index 000000000000..57663492b228
> > --- /dev/null
> > +++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> > @@ -0,0 +1,171 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/* Copyright (c) 2018, Broadcom */
> > +
> > +/*
> > + * This module contains USB PHY initialization for power up and S3 resume
> > + * for newer Synopsis based USB hardware first used on the bcm7216.
> > + */
> > +
> > +#include <linux/delay.h>
> > +#include <linux/io.h>
> > +
> > +#include <linux/soc/brcmstb/brcmstb.h>
> > +#include "phy-brcm-usb-init.h"
> > +
> > +/* Register definitions for the USB CTRL block */
> > +#define USB_CTRL_SETUP                       0x00
> > +#define   USB_CTRL_SETUP_STRAP_IPP_SEL_MASK          0x02000000
> > +#define   USB_CTRL_SETUP_SCB2_EN_MASK                        0x00008000
> > +#define   USB_CTRL_SETUP_SCB1_EN_MASK                        0x00004000
> > +#define   USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK          0x00000200
> > +#define   USB_CTRL_SETUP_IPP_MASK                    0x00000020
> > +#define   USB_CTRL_SETUP_IOC_MASK                    0x00000010
> > +#define USB_CTRL_USB_PM                      0x04
> > +#define   USB_CTRL_USB_PM_USB_PWRDN_MASK             0x80000000
> > +#define   USB_CTRL_USB_PM_SOFT_RESET_MASK            0x40000000
> > +#define   USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK               0x00800000
> > +#define   USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK               0x00400000
> > +#define USB_CTRL_USB_PM_STATUS               0x08
> > +#define USB_CTRL_USB_DEVICE_CTL1     0x10
> > +#define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK    0x00000003
> > +
> > +
> > +static void xhci_soft_reset(struct brcm_usb_init_params *params,
> > +                     int on_off)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +
> > +     /* Assert reset */
> > +     if (on_off)
> > +             USB_CTRL_UNSET(ctrl, USB_PM, XHC_SOFT_RESETB);
> > +     /* De-assert reset */
> > +     else
> > +             USB_CTRL_SET(ctrl, USB_PM, XHC_SOFT_RESETB);
> > +}
> > +
> > +static void usb_init_ipp(struct brcm_usb_init_params *params)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +     u32 reg;
> > +     u32 orig_reg;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     orig_reg = reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
> > +     if (params->ipp != 2)
> > +             /* override ipp strap pin (if it exits) */
> > +             reg &= ~(USB_CTRL_MASK(SETUP, STRAP_IPP_SEL));
> > +
> > +     /* Override the default OC and PP polarity */
> > +     reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
> > +     if (params->ioc)
> > +             reg |= USB_CTRL_MASK(SETUP, IOC);
> > +     if (params->ipp == 1)
> > +             reg |= USB_CTRL_MASK(SETUP, IPP);
> > +     brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
> > +
> > +     /*
> > +      * If we're changing IPP, make sure power is off long enough
> > +      * to turn off any connected devices.
> > +      */
> > +     if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
> > +             msleep(50);
> > +}
> > +
> > +static void usb_init_common(struct brcm_usb_init_params *params)
> > +{
> > +     u32 reg;
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
> > +     /* 1 millisecond - for USB clocks to settle down */
> > +     usleep_range(1000, 2000);
> > +
> > +     if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
> > +             reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +             reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> > +             reg |= params->mode;
> > +             brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +     }
> > +     switch (params->mode) {
> > +     case USB_CTLR_MODE_HOST:
> > +             USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
> > +             break;
> > +     default:
> > +             USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
> > +             USB_CTRL_SET(ctrl, USB_PM, BDC_SOFT_RESETB);
> > +             break;
> > +     }
> > +}
> > +
> > +static void usb_init_xhci(struct brcm_usb_init_params *params)
> > +{
> > +     pr_debug("%s\n", __func__);
> > +
> > +     xhci_soft_reset(params, 0);
> > +}
> > +
> > +static void usb_uninit_common(struct brcm_usb_init_params *params)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
> > +
> > +}
> > +
> > +static void usb_uninit_xhci(struct brcm_usb_init_params *params)
> > +{
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     xhci_soft_reset(params, 1);
> > +}
> > +
> > +static int usb_get_dual_select(struct brcm_usb_init_params *params)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +     u32 reg = 0;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +     reg &= USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> > +     return reg;
> > +}
> > +
> > +static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
> > +{
> > +     void __iomem *ctrl = params->ctrl_regs;
> > +     u32 reg;
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +     reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
> > +     reg |= mode;
> > +     brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
> > +}
> > +
> > +
> > +static const struct brcm_usb_init_ops bcm7216_ops = {
> > +     .init_ipp = usb_init_ipp,
> > +     .init_common = usb_init_common,
> > +     .init_xhci = usb_init_xhci,
> > +     .uninit_common = usb_uninit_common,
> > +     .uninit_xhci = usb_uninit_xhci,
> > +     .get_dual_select = usb_get_dual_select,
> > +     .set_dual_select = usb_set_dual_select,
> > +};
> > +
> > +void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
> > +{
> > +
> > +     pr_debug("%s\n", __func__);
> > +
> > +     params->family_name = "7216";
> > +     params->ops = &bcm7216_ops;
> > +}
> > diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
> > index 7701872d1136..db6851c55335 100644
> > --- a/drivers/phy/broadcom/phy-brcm-usb-init.h
> > +++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
> > @@ -43,6 +43,7 @@ struct brcm_usb_init_ops {
> >  struct  brcm_usb_init_params {
> >       void __iomem *ctrl_regs;
> >       void __iomem *xhci_ec_regs;
> > +     void __iomem *xhci_gbl_regs;
> >       int ioc;
> >       int ipp;
> >       int mode;
> > @@ -55,6 +56,7 @@ struct  brcm_usb_init_params {
> >  };
> >
> >  void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
> > +void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
> >
> >  static inline u32 brcm_usb_readl(void __iomem *addr)
> >  {
> > diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
> > index 9d93c5599511..64379ede480e 100644
> > --- a/drivers/phy/broadcom/phy-brcm-usb.c
> > +++ b/drivers/phy/broadcom/phy-brcm-usb.c
> > @@ -241,6 +241,15 @@ static const struct attribute_group brcm_usb_phy_group = {
> >       .attrs = brcm_usb_phy_attrs,
> >  };
> >
> > +static const struct of_device_id brcm_usb_dt_ids[] = {
> > +     {
> > +             .compatible = "brcm,bcm7216-usb-phy",
> > +             .data = &brcm_usb_dvr_init_7216,
> > +     },
> > +     { .compatible = "brcm,brcmstb-usb-phy" },
> > +     { /* sentinel */ }
> > +};
> > +
> >  static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
> >                                struct brcm_usb_phy_data *priv,
> >                                struct device_node *dn)
> > @@ -316,13 +325,16 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
> >
> >  static int brcm_usb_phy_probe(struct platform_device *pdev)
> >  {
> > -     struct resource *res;
> > +     struct resource *res_ctrl;
> > +     struct resource *res_xhciec = NULL;
> > +     struct resource *res_xhcigbl = NULL;
> >       struct device *dev = &pdev->dev;
> >       struct brcm_usb_phy_data *priv;
> >       struct phy_provider *phy_provider;
> >       struct device_node *dn = pdev->dev.of_node;
> >       int err;
> >       const char *mode;
> > +     const struct of_device_id *match;
> >
> >       priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> >       if (!priv)
> > @@ -331,30 +343,59 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
> >
> >       priv->ini.family_id = brcmstb_get_family_id();
> >       priv->ini.product_id = brcmstb_get_product_id();
> > -     brcm_usb_dvr_init_7445(&priv->ini);
> > +
> > +     match = of_match_node(brcm_usb_dt_ids, dev->of_node);
> > +     if (match && match->data) {
> > +             void (*dvr_init)(struct brcm_usb_init_params *params);
> > +
> > +             dvr_init = match->data;
> > +             (*dvr_init)(&priv->ini);
> > +     } else {
> > +             brcm_usb_dvr_init_7445(&priv->ini);
> > +     }
> > +
> >       dev_dbg(dev, "Best mapping table is for %s\n",
> >               priv->ini.family_name);
> > -     res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > -     if (!res) {
> > -             dev_err(dev, "can't get USB_CTRL base address\n");
> > -             return -EINVAL;
> > +
> > +     /* Newer DT node has reg-names. xhci_ec and xhci_gbl are optional. */
> > +     res_ctrl = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
> > +     if (res_ctrl != NULL) {
> > +             res_xhciec = platform_get_resource_byname(pdev,
> > +                                                       IORESOURCE_MEM,
> > +                                                       "xhci_ec");
> > +             res_xhcigbl = platform_get_resource_byname(pdev,
> > +                                                        IORESOURCE_MEM,
> > +                                                        "xhci_gbl");
> > +     } else {
> > +             /* Older DT node without reg-names, use index */
> > +             res_ctrl = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > +             if (res_ctrl == NULL) {
> > +                     dev_err(dev, "can't get CTRL base address\n");
> > +                     return -EINVAL;
> > +             }
> > +             res_xhciec = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> >       }
> > -     priv->ini.ctrl_regs = devm_ioremap_resource(dev, res);
> > +     priv->ini.ctrl_regs = devm_ioremap_resource(dev, res_ctrl);
> >       if (IS_ERR(priv->ini.ctrl_regs)) {
> >               dev_err(dev, "can't map CTRL register space\n");
> >               return -EINVAL;
> >       }
> > -
> > -     /* The XHCI EC registers are optional */
> > -     res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> > -     if (res) {
> > +     if (res_xhciec) {
> >               priv->ini.xhci_ec_regs =
> > -                     devm_ioremap_resource(dev, res);
> > +                     devm_ioremap_resource(dev, res_xhciec);
> >               if (IS_ERR(priv->ini.xhci_ec_regs)) {
> >                       dev_err(dev, "can't map XHCI EC register space\n");
> >                       return -EINVAL;
> >               }
> >       }
> > +     if (res_xhcigbl) {
> > +             priv->ini.xhci_gbl_regs =
> > +                     devm_ioremap_resource(dev, res_xhcigbl);
> > +             if (IS_ERR(priv->ini.xhci_gbl_regs)) {
> > +                     dev_err(dev, "can't map XHCI Global register space\n");
> > +                     return -EINVAL;
> > +             }
> > +     }
> >
> >       of_property_read_u32(dn, "brcm,ipp", &priv->ini.ipp);
> >       of_property_read_u32(dn, "brcm,ioc", &priv->ini.ioc);
> > @@ -480,11 +521,6 @@ static const struct dev_pm_ops brcm_usb_phy_pm_ops = {
> >       SET_LATE_SYSTEM_SLEEP_PM_OPS(brcm_usb_phy_suspend, brcm_usb_phy_resume)
> >  };
> >
> > -static const struct of_device_id brcm_usb_dt_ids[] = {
> > -     { .compatible = "brcm,brcmstb-usb-phy" },
> > -     { /* sentinel */ }
> > -};
> > -
> >  MODULE_DEVICE_TABLE(of, brcm_usb_dt_ids);
> >
> >  static struct platform_driver brcm_usb_driver = {
> >

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 08/13] phy: usb: Add support for new Synopsis USB controller on the 7211b0

[Al Cooper]

The 7211b0 has added the STB XHCI Synopsis controller and it
will be used instead of the RPi based DWC USB controller. The new
Synopsis XHCI controller core is the same one that is used on the
7216, but because of the way the STB USB PHY is used on both the A0
and B0, some of the PHY control is different.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 163 +++++++++++++++++-
 drivers/phy/broadcom/phy-brcm-usb-init.c      |  31 ++--
 drivers/phy/broadcom/phy-brcm-usb-init.h      |  17 +-
 drivers/phy/broadcom/phy-brcm-usb.c           | 162 +++++++++++------
 4 files changed, 295 insertions(+), 78 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
index 57663492b228..bf138867efb1 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -12,10 +12,33 @@
 #include <linux/soc/brcmstb/brcmstb.h>
 #include "phy-brcm-usb-init.h"
 
+#define PHY_LOCK_TIMEOUT_MS 200
+
+/* Register definitions for syscon piarbctl registers */
+#define PIARBCTL_CAM			0x00
+#define PIARBCTL_SPLITTER		0x04
+#define PIARBCTL_MISC			0x08
+#define   PIARBCTL_MISC_SECURE_MASK			0x80000000
+#define   PIARBCTL_MISC_USB_SELECT_MASK			0x40000000
+#define   PIARBCTL_MISC_USB_4G_SDRAM_MASK		0x20000000
+#define   PIARBCTL_MISC_USB_PRIORITY_MASK		0x000f0000
+#define   PIARBCTL_MISC_USB_MEM_PAGE_MASK		0x0000f000
+#define   PIARBCTL_MISC_CAM1_MEM_PAGE_MASK		0x00000f00
+#define   PIARBCTL_MISC_CAM0_MEM_PAGE_MASK		0x000000f0
+#define   PIARBCTL_MISC_SATA_PRIORITY_MASK		0x0000000f
+#define PIARBCTL_USB_M_ASB_CTRL		0x10
+
+#define PIARBCTL_MISC_USB_ONLY_MASK		\
+	(PIARBCTL_MISC_USB_SELECT_MASK |	\
+	 PIARBCTL_MISC_USB_4G_SDRAM_MASK |	\
+	 PIARBCTL_MISC_USB_PRIORITY_MASK |	\
+	 PIARBCTL_MISC_USB_MEM_PAGE_MASK)
+
 /* Register definitions for the USB CTRL block */
 #define USB_CTRL_SETUP			0x00
 #define   USB_CTRL_SETUP_STRAP_IPP_SEL_MASK		0x02000000
 #define   USB_CTRL_SETUP_SCB2_EN_MASK			0x00008000
+#define   USB_CTRL_SETUP_tca_drv_sel_MASK		0x01000000
 #define   USB_CTRL_SETUP_SCB1_EN_MASK			0x00004000
 #define   USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK		0x00000200
 #define   USB_CTRL_SETUP_IPP_MASK			0x00000020
@@ -29,11 +52,73 @@
 #define USB_CTRL_USB_DEVICE_CTL1	0x10
 #define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK	0x00000003
 
+/* Register definitions for the USB_PHY block in 7211b0 */
+#define USB_PHY_PLL_LDO_CTL		0x08
+#define   USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK		0x00000004
+#define USB_PHY_UTMI_CTL_1		0x04
+#define   USB_PHY_UTMI_CTL_1_PHY_MODE_MASK		0x0000000c
+#define   USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT		2
+#define USB_PHY_STATUS			0x20
+#define   USB_PHY_STATUS_pll_lock_MASK			0x00000001
+
+/* Register definitions for the MDIO registers in the DWC2 block of
+ * the 7211b0.
+ * NOTE: The PHY's MDIO registers are only accessible through the
+ * legacy DesignWare USB controller even though it's not being used.
+ */
+#define USB_GMDIOCSR	0
+#define USB_GMDIOGEN	4
+
+
+static void usb_mdio_write_7211b0(struct brcm_usb_init_params *params,
+				  uint8_t addr, uint16_t data)
+{
+	void __iomem *usb_mdio = params->regs[BRCM_REGS_USB_MDIO];
+
+	addr &= 0x1f; /* 5-bit address */
+	brcm_usb_writel(0xffffffff, usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+	brcm_usb_writel(0x59020000 | (addr << 18) | data,
+			usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+	brcm_usb_writel(0x00000000, usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+}
+
+static uint16_t __maybe_unused usb_mdio_read_7211b0(
+	struct brcm_usb_init_params *params, uint8_t addr)
+{
+	void __iomem *usb_mdio = params->regs[BRCM_REGS_USB_MDIO];
+
+	addr &= 0x1f; /* 5-bit address */
+	brcm_usb_writel(0xffffffff, usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+	brcm_usb_writel(0x69020000 | (addr << 18), usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+	brcm_usb_writel(0x00000000, usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+	return brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & 0xffff;
+}
+
+static void usb2_eye_fix_7211b0(struct brcm_usb_init_params *params)
+{
+	/* select bank */
+	usb_mdio_write_7211b0(params, 0x1f, 0x80a0);
+
+	/* Set the eye */
+	usb_mdio_write_7211b0(params, 0x0a, 0xc6a0);
+}
 
 static void xhci_soft_reset(struct brcm_usb_init_params *params,
 			int on_off)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	/* Assert reset */
 	if (on_off)
@@ -45,7 +130,7 @@ static void xhci_soft_reset(struct brcm_usb_init_params *params,
 
 static void usb_init_ipp(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg;
 	u32 orig_reg;
 
@@ -72,10 +157,18 @@ static void usb_init_ipp(struct brcm_usb_init_params *params)
 		msleep(50);
 }
 
+static void syscon_piarbctl_init(struct regmap *rmap)
+{
+	/* Switch from legacy USB OTG controller to new STB USB controller */
+	regmap_update_bits(rmap, PIARBCTL_MISC, PIARBCTL_MISC_USB_ONLY_MASK,
+			   PIARBCTL_MISC_USB_SELECT_MASK |
+			   PIARBCTL_MISC_USB_4G_SDRAM_MASK);
+}
+
 static void usb_init_common(struct brcm_usb_init_params *params)
 {
 	u32 reg;
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	pr_debug("%s\n", __func__);
 
@@ -100,6 +193,45 @@ static void usb_init_common(struct brcm_usb_init_params *params)
 	}
 }
 
+static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+	void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
+	int timeout_ms = PHY_LOCK_TIMEOUT_MS;
+	u32 reg;
+
+	if (params->syscon_piarbctl)
+		syscon_piarbctl_init(params->syscon_piarbctl);
+
+	/* Init the PHY */
+	reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_LDO_CTL);
+	reg |= USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK;
+	brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_LDO_CTL);
+
+	/* wait for lock */
+	while (timeout_ms-- > 0) {
+		reg = brcm_usb_readl(usb_phy + USB_PHY_STATUS);
+		if (reg & USB_PHY_STATUS_pll_lock_MASK)
+			break;
+		usleep_range(1000, 2000);
+	}
+
+	/* Set the PHY_MODE */
+	reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
+	reg &= ~USB_PHY_UTMI_CTL_1_PHY_MODE_MASK;
+	reg |= params->mode << USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT;
+	brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
+
+	/* Fix the incorrect default */
+	reg = brcm_usb_readl(ctrl + USB_CTRL_SETUP);
+	reg &= ~USB_CTRL_SETUP_tca_drv_sel_MASK;
+	brcm_usb_writel(reg, ctrl + USB_CTRL_SETUP);
+
+	usb_init_common(params);
+
+	usb2_eye_fix_7211b0(params);
+}
+
 static void usb_init_xhci(struct brcm_usb_init_params *params)
 {
 	pr_debug("%s\n", __func__);
@@ -109,7 +241,7 @@ static void usb_init_xhci(struct brcm_usb_init_params *params)
 
 static void usb_uninit_common(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	pr_debug("%s\n", __func__);
 
@@ -127,7 +259,7 @@ static void usb_uninit_xhci(struct brcm_usb_init_params *params)
 
 static int usb_get_dual_select(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg = 0;
 
 	pr_debug("%s\n", __func__);
@@ -139,7 +271,7 @@ static int usb_get_dual_select(struct brcm_usb_init_params *params)
 
 static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg;
 
 	pr_debug("%s\n", __func__);
@@ -161,6 +293,16 @@ static const struct brcm_usb_init_ops bcm7216_ops = {
 	.set_dual_select = usb_set_dual_select,
 };
 
+static const struct brcm_usb_init_ops bcm7211b0_ops = {
+	.init_ipp = usb_init_ipp,
+	.init_common = usb_init_common_7211b0,
+	.init_xhci = usb_init_xhci,
+	.uninit_common = usb_uninit_common,
+	.uninit_xhci = usb_uninit_xhci,
+	.get_dual_select = usb_get_dual_select,
+	.set_dual_select = usb_set_dual_select,
+};
+
 void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
 {
 
@@ -169,3 +311,12 @@ void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
 	params->family_name = "7216";
 	params->ops = &bcm7216_ops;
 }
+
+void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params)
+{
+
+	pr_debug("%s\n", __func__);
+
+	params->family_name = "7211";
+	params->ops = &bcm7211b0_ops;
+}
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index 80d6f54d276e..17acc3c1051b 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -401,7 +401,7 @@ void usb_ctrl_unset_family(struct brcm_usb_init_params *params,
 	u32 mask;
 
 	mask = params->usb_reg_bits_map[field];
-	brcm_usb_ctrl_unset(params->ctrl_regs + reg_offset, mask);
+	brcm_usb_ctrl_unset(params->regs[BRCM_REGS_CTRL] + reg_offset, mask);
 };
 
 static inline
@@ -411,7 +411,7 @@ void usb_ctrl_set_family(struct brcm_usb_init_params *params,
 	u32 mask;
 
 	mask = params->usb_reg_bits_map[field];
-	brcm_usb_ctrl_set(params->ctrl_regs + reg_offset, mask);
+	brcm_usb_ctrl_set(params->regs[BRCM_REGS_CTRL] + reg_offset, mask);
 };
 
 static u32 brcmusb_usb_mdio_read(void __iomem *ctrl_base, u32 reg, int mode)
@@ -544,7 +544,7 @@ static void brcmusb_usb3_pll_54mhz(struct brcm_usb_init_params *params)
 {
 	u32 ofs;
 	int ii;
-	void __iomem *ctrl_base = params->ctrl_regs;
+	void __iomem *ctrl_base = params->regs[BRCM_REGS_CTRL];
 
 	/*
 	 * On newer B53 based SoC's, the reference clock for the
@@ -625,7 +625,7 @@ static void brcmusb_usb3_ssc_enable(void __iomem *ctrl_base)
 
 static void brcmusb_usb3_phy_workarounds(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl_base = params->ctrl_regs;
+	void __iomem *ctrl_base = params->regs[BRCM_REGS_CTRL];
 
 	brcmusb_usb3_pll_fix(ctrl_base);
 	brcmusb_usb3_pll_54mhz(params);
@@ -667,7 +667,7 @@ static void brcmusb_memc_fix(struct brcm_usb_init_params *params)
 
 static void brcmusb_usb3_otp_fix(struct brcm_usb_init_params *params)
 {
-	void __iomem *xhci_ec_base = params->xhci_ec_regs;
+	void __iomem *xhci_ec_base = params->regs[BRCM_REGS_XHCI_EC];
 	u32 val;
 
 	if (params->family_id != 0x74371000 || !xhci_ec_base)
@@ -680,8 +680,8 @@ static void brcmusb_usb3_otp_fix(struct brcm_usb_init_params *params)
 	brcm_usb_writel(val, USB_XHCI_EC_REG(xhci_ec_base, IRADAT));
 
 	/* Reset USB 3.0 PHY for workaround to take effect */
-	USB_CTRL_UNSET(params->ctrl_regs, USB30_CTL1, PHY3_RESETB);
-	USB_CTRL_SET(params->ctrl_regs,	USB30_CTL1, PHY3_RESETB);
+	USB_CTRL_UNSET(params->regs[BRCM_REGS_CTRL], USB30_CTL1, PHY3_RESETB);
+	USB_CTRL_SET(params->regs[BRCM_REGS_CTRL], USB30_CTL1, PHY3_RESETB);
 }
 
 static void brcmusb_xhci_soft_reset(struct brcm_usb_init_params *params,
@@ -740,7 +740,7 @@ static enum brcm_family_type get_family_type(
 
 static void usb_init_ipp(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg;
 	u32 orig_reg;
 
@@ -786,7 +786,7 @@ static void usb_init_ipp(struct brcm_usb_init_params *params)
 static void usb_init_common(struct brcm_usb_init_params *params)
 {
 	u32 reg;
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	/* Clear any pending wake conditions */
 	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
@@ -866,7 +866,7 @@ static void usb_init_common(struct brcm_usb_init_params *params)
 static void usb_init_eohci(struct brcm_usb_init_params *params)
 {
 	u32 reg;
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	if (USB_CTRL_MASK_FAMILY(params, USB_PM, USB20_HC_RESETB))
 		USB_CTRL_SET_FAMILY(params, USB_PM, USB20_HC_RESETB);
@@ -902,7 +902,7 @@ static void usb_init_eohci(struct brcm_usb_init_params *params)
 
 static void usb_init_xhci(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	USB_CTRL_UNSET(ctrl, USB30_PCTL, PHY3_IDDQ_OVERRIDE);
 	/* 1 millisecond - for USB clocks to settle down */
@@ -944,12 +944,13 @@ static void usb_uninit_eohci(struct brcm_usb_init_params *params)
 static void usb_uninit_xhci(struct brcm_usb_init_params *params)
 {
 	brcmusb_xhci_soft_reset(params, 1);
-	USB_CTRL_SET(params->ctrl_regs, USB30_PCTL, PHY3_IDDQ_OVERRIDE);
+	USB_CTRL_SET(params->regs[BRCM_REGS_CTRL], USB30_PCTL,
+		     PHY3_IDDQ_OVERRIDE);
 }
 
 static int usb_get_dual_select(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg = 0;
 
 	pr_debug("%s\n", __func__);
@@ -963,7 +964,7 @@ static int usb_get_dual_select(struct brcm_usb_init_params *params)
 
 static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg;
 
 	pr_debug("%s\n", __func__);
@@ -980,7 +981,7 @@ static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 static void usb_wake_enable(struct brcm_usb_init_params *params,
 			  int enable)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	if (enable)
 		USB_CTRL_SET(ctrl, USB_PM, RMTWKUP_EN);
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index db6851c55335..2ea81daf295e 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -6,12 +6,21 @@
 #ifndef _USB_BRCM_COMMON_INIT_H
 #define _USB_BRCM_COMMON_INIT_H
 
+#include <linux/regmap.h>
+
 #define USB_CTLR_MODE_HOST 0
 #define USB_CTLR_MODE_DEVICE 1
 #define USB_CTLR_MODE_DRD 2
 #define USB_CTLR_MODE_TYPEC_PD 3
 
-struct  brcm_usb_init_params;
+enum brcmusb_reg_sel {
+	BRCM_REGS_CTRL = 0,
+	BRCM_REGS_XHCI_EC,
+	BRCM_REGS_XHCI_GBL,
+	BRCM_REGS_USB_PHY,
+	BRCM_REGS_USB_MDIO,
+	BRCM_REGS_MAX
+};
 
 #define USB_CTRL_REG(base, reg)	((void __iomem *)base + USB_CTRL_##reg)
 #define USB_XHCI_EC_REG(base, reg) ((void __iomem *)base + USB_XHCI_EC_##reg)
@@ -41,9 +50,7 @@ struct brcm_usb_init_ops {
 };
 
 struct  brcm_usb_init_params {
-	void __iomem *ctrl_regs;
-	void __iomem *xhci_ec_regs;
-	void __iomem *xhci_gbl_regs;
+	void __iomem *regs[BRCM_REGS_MAX];
 	int ioc;
 	int ipp;
 	int mode;
@@ -53,10 +60,12 @@ struct  brcm_usb_init_params {
 	const char *family_name;
 	const u32 *usb_reg_bits_map;
 	const struct brcm_usb_init_ops *ops;
+	struct regmap *syscon_piarbctl;
 };
 
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
 void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
+void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params);
 
 static inline u32 brcm_usb_readl(void __iomem *addr)
 {
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 64379ede480e..5f7bfa09494d 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -16,6 +16,7 @@
 #include <linux/interrupt.h>
 #include <linux/soc/brcmstb/brcmstb.h>
 #include <dt-bindings/phy/phy.h>
+#include <linux/mfd/syscon.h>
 
 #include "phy-brcm-usb-init.h"
 
@@ -32,6 +33,11 @@ struct value_to_name_map {
 	const char *name;
 };
 
+struct match_chip_info {
+	void *init_func;
+	u8 required_regs[BRCM_REGS_MAX + 1];
+};
+
 static struct value_to_name_map brcm_dr_mode_to_name[] = {
 	{ USB_CTLR_MODE_HOST, "host" },
 	{ USB_CTLR_MODE_DEVICE, "peripheral" },
@@ -64,6 +70,10 @@ struct brcm_usb_phy_data {
 	struct brcm_usb_phy	phys[BRCM_USB_PHY_ID_MAX];
 };
 
+static s8 *node_reg_names[BRCM_REGS_MAX] = {
+	"crtl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio"
+};
+
 static irqreturn_t brcm_usb_phy_wake_isr(int irq, void *dev_id)
 {
 	struct phy *gphy = dev_id;
@@ -241,15 +251,86 @@ static const struct attribute_group brcm_usb_phy_group = {
 	.attrs = brcm_usb_phy_attrs,
 };
 
+static struct match_chip_info chip_info_7216 = {
+	.init_func = &brcm_usb_dvr_init_7216,
+	.required_regs = {
+		BRCM_REGS_CTRL,
+		BRCM_REGS_XHCI_EC,
+		BRCM_REGS_XHCI_GBL,
+		-1,
+	},
+};
+
+static struct match_chip_info chip_info_7211b0 = {
+	.init_func = &brcm_usb_dvr_init_7211b0,
+	.required_regs = {
+		BRCM_REGS_CTRL,
+		BRCM_REGS_XHCI_EC,
+		BRCM_REGS_XHCI_GBL,
+		BRCM_REGS_USB_PHY,
+		BRCM_REGS_USB_MDIO,
+		-1,
+	},
+};
+
+static struct match_chip_info chip_info_7445 = {
+	.init_func = &brcm_usb_dvr_init_7445,
+	.required_regs = {
+		BRCM_REGS_CTRL,
+		BRCM_REGS_XHCI_EC,
+		-1,
+	},
+};
+
 static const struct of_device_id brcm_usb_dt_ids[] = {
 	{
 		.compatible = "brcm,bcm7216-usb-phy",
-		.data = &brcm_usb_dvr_init_7216,
+		.data = &chip_info_7216,
+	},
+	{
+		.compatible = "brcm,bcm7211-usb-phy",
+		.data = &chip_info_7211b0,
+	},
+	{
+		.compatible = "brcm,brcmstb-usb-phy",
+		.data = &chip_info_7445,
 	},
-	{ .compatible = "brcm,brcmstb-usb-phy" },
 	{ /* sentinel */ }
 };
 
+static int brcm_usb_get_regs(struct platform_device *pdev,
+			     enum brcmusb_reg_sel regs,
+			     struct  brcm_usb_init_params *ini)
+{
+	struct resource *res;
+
+	/* Older DT nodes have ctrl and optional xhci_ec by index only */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						node_reg_names[regs]);
+	if (res == NULL) {
+		if (regs == BRCM_REGS_CTRL) {
+			res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		} else if (regs == BRCM_REGS_XHCI_EC) {
+			res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+			/* XHCI_EC registers are optional */
+			if (res == NULL)
+				return 0;
+		}
+		if (res == NULL) {
+			dev_err(&pdev->dev, "can't get %s base address\n",
+				node_reg_names[regs]);
+			return 1;
+		}
+	}
+	ini->regs[regs] = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ini->regs[regs])) {
+		dev_err(&pdev->dev, "can't map %s register space\n",
+			node_reg_names[regs]);
+		return 1;
+	}
+	return 0;
+}
+
 static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 				 struct brcm_usb_phy_data *priv,
 				 struct device_node *dn)
@@ -325,9 +406,6 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 
 static int brcm_usb_phy_probe(struct platform_device *pdev)
 {
-	struct resource *res_ctrl;
-	struct resource *res_xhciec = NULL;
-	struct resource *res_xhcigbl = NULL;
 	struct device *dev = &pdev->dev;
 	struct brcm_usb_phy_data *priv;
 	struct phy_provider *phy_provider;
@@ -335,6 +413,10 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	int err;
 	const char *mode;
 	const struct of_device_id *match;
+	void (*dvr_init)(struct brcm_usb_init_params *params);
+	const struct match_chip_info *info;
+	struct regmap *rmap;
+	int x;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -345,58 +427,13 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	priv->ini.product_id = brcmstb_get_product_id();
 
 	match = of_match_node(brcm_usb_dt_ids, dev->of_node);
-	if (match && match->data) {
-		void (*dvr_init)(struct brcm_usb_init_params *params);
-
-		dvr_init = match->data;
-		(*dvr_init)(&priv->ini);
-	} else {
-		brcm_usb_dvr_init_7445(&priv->ini);
-	}
+	info = match->data;
+	dvr_init = info->init_func;
+	(*dvr_init)(&priv->ini);
 
 	dev_dbg(dev, "Best mapping table is for %s\n",
 		priv->ini.family_name);
 
-	/* Newer DT node has reg-names. xhci_ec and xhci_gbl are optional. */
-	res_ctrl = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
-	if (res_ctrl != NULL) {
-		res_xhciec = platform_get_resource_byname(pdev,
-							  IORESOURCE_MEM,
-							  "xhci_ec");
-		res_xhcigbl = platform_get_resource_byname(pdev,
-							   IORESOURCE_MEM,
-							   "xhci_gbl");
-	} else {
-		/* Older DT node without reg-names, use index */
-		res_ctrl = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-		if (res_ctrl == NULL) {
-			dev_err(dev, "can't get CTRL base address\n");
-			return -EINVAL;
-		}
-		res_xhciec = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	}
-	priv->ini.ctrl_regs = devm_ioremap_resource(dev, res_ctrl);
-	if (IS_ERR(priv->ini.ctrl_regs)) {
-		dev_err(dev, "can't map CTRL register space\n");
-		return -EINVAL;
-	}
-	if (res_xhciec) {
-		priv->ini.xhci_ec_regs =
-			devm_ioremap_resource(dev, res_xhciec);
-		if (IS_ERR(priv->ini.xhci_ec_regs)) {
-			dev_err(dev, "can't map XHCI EC register space\n");
-			return -EINVAL;
-		}
-	}
-	if (res_xhcigbl) {
-		priv->ini.xhci_gbl_regs =
-			devm_ioremap_resource(dev, res_xhcigbl);
-		if (IS_ERR(priv->ini.xhci_gbl_regs)) {
-			dev_err(dev, "can't map XHCI Global register space\n");
-			return -EINVAL;
-		}
-	}
-
 	of_property_read_u32(dn, "brcm,ipp", &priv->ini.ipp);
 	of_property_read_u32(dn, "brcm,ioc", &priv->ini.ioc);
 
@@ -412,6 +449,16 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	if (of_property_read_bool(dn, "brcm,has-eohci"))
 		priv->has_eohci = true;
 
+	for (x = 0; x < BRCM_REGS_MAX; x++) {
+		if (info->required_regs[x] >= BRCM_REGS_MAX)
+			break;
+
+		err = brcm_usb_get_regs(pdev, info->required_regs[x],
+					&priv->ini);
+		if (err)
+			return -EINVAL;
+	}
+
 	err = brcm_usb_phy_dvr_init(pdev, priv, dn);
 	if (err)
 		return err;
@@ -431,6 +478,15 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	if (err)
 		dev_warn(dev, "Error creating sysfs attributes\n");
 
+	/* Get piarbctl syscon if it exists */
+	rmap = syscon_regmap_lookup_by_phandle(dev->of_node,
+						 "syscon-piarbctl");
+	if (IS_ERR(rmap))
+		rmap = syscon_regmap_lookup_by_phandle(dev->of_node,
+						       "brcm,syscon-piarbctl");
+	if (!IS_ERR(rmap))
+		priv->ini.syscon_piarbctl = rmap;
+
 	/* start with everything off */
 	if (priv->has_xhci)
 		brcm_usb_uninit_xhci(&priv->ini);
-- 
2.17.1

[PATCH v3 08/13] phy: usb: Add support for new Synopsis USB controller on the 7211b0

[Al Cooper]

The 7211b0 has added the STB XHCI Synopsis controller and it
will be used instead of the RPi based DWC USB controller. The new
Synopsis XHCI controller core is the same one that is used on the
7216, but because of the way the STB USB PHY is used on both the A0
and B0, some of the PHY control is different.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 163 +++++++++++++++++-
 drivers/phy/broadcom/phy-brcm-usb-init.c      |  31 ++--
 drivers/phy/broadcom/phy-brcm-usb-init.h      |  17 +-
 drivers/phy/broadcom/phy-brcm-usb.c           | 162 +++++++++++------
 4 files changed, 295 insertions(+), 78 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
index 57663492b228..bf138867efb1 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -12,10 +12,33 @@
 #include <linux/soc/brcmstb/brcmstb.h>
 #include "phy-brcm-usb-init.h"
 
+#define PHY_LOCK_TIMEOUT_MS 200
+
+/* Register definitions for syscon piarbctl registers */
+#define PIARBCTL_CAM			0x00
+#define PIARBCTL_SPLITTER		0x04
+#define PIARBCTL_MISC			0x08
+#define   PIARBCTL_MISC_SECURE_MASK			0x80000000
+#define   PIARBCTL_MISC_USB_SELECT_MASK			0x40000000
+#define   PIARBCTL_MISC_USB_4G_SDRAM_MASK		0x20000000
+#define   PIARBCTL_MISC_USB_PRIORITY_MASK		0x000f0000
+#define   PIARBCTL_MISC_USB_MEM_PAGE_MASK		0x0000f000
+#define   PIARBCTL_MISC_CAM1_MEM_PAGE_MASK		0x00000f00
+#define   PIARBCTL_MISC_CAM0_MEM_PAGE_MASK		0x000000f0
+#define   PIARBCTL_MISC_SATA_PRIORITY_MASK		0x0000000f
+#define PIARBCTL_USB_M_ASB_CTRL		0x10
+
+#define PIARBCTL_MISC_USB_ONLY_MASK		\
+	(PIARBCTL_MISC_USB_SELECT_MASK |	\
+	 PIARBCTL_MISC_USB_4G_SDRAM_MASK |	\
+	 PIARBCTL_MISC_USB_PRIORITY_MASK |	\
+	 PIARBCTL_MISC_USB_MEM_PAGE_MASK)
+
 /* Register definitions for the USB CTRL block */
 #define USB_CTRL_SETUP			0x00
 #define   USB_CTRL_SETUP_STRAP_IPP_SEL_MASK		0x02000000
 #define   USB_CTRL_SETUP_SCB2_EN_MASK			0x00008000
+#define   USB_CTRL_SETUP_tca_drv_sel_MASK		0x01000000
 #define   USB_CTRL_SETUP_SCB1_EN_MASK			0x00004000
 #define   USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK		0x00000200
 #define   USB_CTRL_SETUP_IPP_MASK			0x00000020
@@ -29,11 +52,73 @@
 #define USB_CTRL_USB_DEVICE_CTL1	0x10
 #define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK	0x00000003
 
+/* Register definitions for the USB_PHY block in 7211b0 */
+#define USB_PHY_PLL_LDO_CTL		0x08
+#define   USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK		0x00000004
+#define USB_PHY_UTMI_CTL_1		0x04
+#define   USB_PHY_UTMI_CTL_1_PHY_MODE_MASK		0x0000000c
+#define   USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT		2
+#define USB_PHY_STATUS			0x20
+#define   USB_PHY_STATUS_pll_lock_MASK			0x00000001
+
+/* Register definitions for the MDIO registers in the DWC2 block of
+ * the 7211b0.
+ * NOTE: The PHY's MDIO registers are only accessible through the
+ * legacy DesignWare USB controller even though it's not being used.
+ */
+#define USB_GMDIOCSR	0
+#define USB_GMDIOGEN	4
+
+
+static void usb_mdio_write_7211b0(struct brcm_usb_init_params *params,
+				  uint8_t addr, uint16_t data)
+{
+	void __iomem *usb_mdio = params->regs[BRCM_REGS_USB_MDIO];
+
+	addr &= 0x1f; /* 5-bit address */
+	brcm_usb_writel(0xffffffff, usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+	brcm_usb_writel(0x59020000 | (addr << 18) | data,
+			usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+	brcm_usb_writel(0x00000000, usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+}
+
+static uint16_t __maybe_unused usb_mdio_read_7211b0(
+	struct brcm_usb_init_params *params, uint8_t addr)
+{
+	void __iomem *usb_mdio = params->regs[BRCM_REGS_USB_MDIO];
+
+	addr &= 0x1f; /* 5-bit address */
+	brcm_usb_writel(0xffffffff, usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+	brcm_usb_writel(0x69020000 | (addr << 18), usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+	brcm_usb_writel(0x00000000, usb_mdio + USB_GMDIOGEN);
+	while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
+		;
+	return brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & 0xffff;
+}
+
+static void usb2_eye_fix_7211b0(struct brcm_usb_init_params *params)
+{
+	/* select bank */
+	usb_mdio_write_7211b0(params, 0x1f, 0x80a0);
+
+	/* Set the eye */
+	usb_mdio_write_7211b0(params, 0x0a, 0xc6a0);
+}
 
 static void xhci_soft_reset(struct brcm_usb_init_params *params,
 			int on_off)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	/* Assert reset */
 	if (on_off)
@@ -45,7 +130,7 @@ static void xhci_soft_reset(struct brcm_usb_init_params *params,
 
 static void usb_init_ipp(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg;
 	u32 orig_reg;
 
@@ -72,10 +157,18 @@ static void usb_init_ipp(struct brcm_usb_init_params *params)
 		msleep(50);
 }
 
+static void syscon_piarbctl_init(struct regmap *rmap)
+{
+	/* Switch from legacy USB OTG controller to new STB USB controller */
+	regmap_update_bits(rmap, PIARBCTL_MISC, PIARBCTL_MISC_USB_ONLY_MASK,
+			   PIARBCTL_MISC_USB_SELECT_MASK |
+			   PIARBCTL_MISC_USB_4G_SDRAM_MASK);
+}
+
 static void usb_init_common(struct brcm_usb_init_params *params)
 {
 	u32 reg;
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	pr_debug("%s\n", __func__);
 
@@ -100,6 +193,45 @@ static void usb_init_common(struct brcm_usb_init_params *params)
 	}
 }
 
+static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+	void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
+	int timeout_ms = PHY_LOCK_TIMEOUT_MS;
+	u32 reg;
+
+	if (params->syscon_piarbctl)
+		syscon_piarbctl_init(params->syscon_piarbctl);
+
+	/* Init the PHY */
+	reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_LDO_CTL);
+	reg |= USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK;
+	brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_LDO_CTL);
+
+	/* wait for lock */
+	while (timeout_ms-- > 0) {
+		reg = brcm_usb_readl(usb_phy + USB_PHY_STATUS);
+		if (reg & USB_PHY_STATUS_pll_lock_MASK)
+			break;
+		usleep_range(1000, 2000);
+	}
+
+	/* Set the PHY_MODE */
+	reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
+	reg &= ~USB_PHY_UTMI_CTL_1_PHY_MODE_MASK;
+	reg |= params->mode << USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT;
+	brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
+
+	/* Fix the incorrect default */
+	reg = brcm_usb_readl(ctrl + USB_CTRL_SETUP);
+	reg &= ~USB_CTRL_SETUP_tca_drv_sel_MASK;
+	brcm_usb_writel(reg, ctrl + USB_CTRL_SETUP);
+
+	usb_init_common(params);
+
+	usb2_eye_fix_7211b0(params);
+}
+
 static void usb_init_xhci(struct brcm_usb_init_params *params)
 {
 	pr_debug("%s\n", __func__);
@@ -109,7 +241,7 @@ static void usb_init_xhci(struct brcm_usb_init_params *params)
 
 static void usb_uninit_common(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	pr_debug("%s\n", __func__);
 
@@ -127,7 +259,7 @@ static void usb_uninit_xhci(struct brcm_usb_init_params *params)
 
 static int usb_get_dual_select(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg = 0;
 
 	pr_debug("%s\n", __func__);
@@ -139,7 +271,7 @@ static int usb_get_dual_select(struct brcm_usb_init_params *params)
 
 static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg;
 
 	pr_debug("%s\n", __func__);
@@ -161,6 +293,16 @@ static const struct brcm_usb_init_ops bcm7216_ops = {
 	.set_dual_select = usb_set_dual_select,
 };
 
+static const struct brcm_usb_init_ops bcm7211b0_ops = {
+	.init_ipp = usb_init_ipp,
+	.init_common = usb_init_common_7211b0,
+	.init_xhci = usb_init_xhci,
+	.uninit_common = usb_uninit_common,
+	.uninit_xhci = usb_uninit_xhci,
+	.get_dual_select = usb_get_dual_select,
+	.set_dual_select = usb_set_dual_select,
+};
+
 void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
 {
 
@@ -169,3 +311,12 @@ void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
 	params->family_name = "7216";
 	params->ops = &bcm7216_ops;
 }
+
+void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params)
+{
+
+	pr_debug("%s\n", __func__);
+
+	params->family_name = "7211";
+	params->ops = &bcm7211b0_ops;
+}
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index 80d6f54d276e..17acc3c1051b 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -401,7 +401,7 @@ void usb_ctrl_unset_family(struct brcm_usb_init_params *params,
 	u32 mask;
 
 	mask = params->usb_reg_bits_map[field];
-	brcm_usb_ctrl_unset(params->ctrl_regs + reg_offset, mask);
+	brcm_usb_ctrl_unset(params->regs[BRCM_REGS_CTRL] + reg_offset, mask);
 };
 
 static inline
@@ -411,7 +411,7 @@ void usb_ctrl_set_family(struct brcm_usb_init_params *params,
 	u32 mask;
 
 	mask = params->usb_reg_bits_map[field];
-	brcm_usb_ctrl_set(params->ctrl_regs + reg_offset, mask);
+	brcm_usb_ctrl_set(params->regs[BRCM_REGS_CTRL] + reg_offset, mask);
 };
 
 static u32 brcmusb_usb_mdio_read(void __iomem *ctrl_base, u32 reg, int mode)
@@ -544,7 +544,7 @@ static void brcmusb_usb3_pll_54mhz(struct brcm_usb_init_params *params)
 {
 	u32 ofs;
 	int ii;
-	void __iomem *ctrl_base = params->ctrl_regs;
+	void __iomem *ctrl_base = params->regs[BRCM_REGS_CTRL];
 
 	/*
 	 * On newer B53 based SoC's, the reference clock for the
@@ -625,7 +625,7 @@ static void brcmusb_usb3_ssc_enable(void __iomem *ctrl_base)
 
 static void brcmusb_usb3_phy_workarounds(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl_base = params->ctrl_regs;
+	void __iomem *ctrl_base = params->regs[BRCM_REGS_CTRL];
 
 	brcmusb_usb3_pll_fix(ctrl_base);
 	brcmusb_usb3_pll_54mhz(params);
@@ -667,7 +667,7 @@ static void brcmusb_memc_fix(struct brcm_usb_init_params *params)
 
 static void brcmusb_usb3_otp_fix(struct brcm_usb_init_params *params)
 {
-	void __iomem *xhci_ec_base = params->xhci_ec_regs;
+	void __iomem *xhci_ec_base = params->regs[BRCM_REGS_XHCI_EC];
 	u32 val;
 
 	if (params->family_id != 0x74371000 || !xhci_ec_base)
@@ -680,8 +680,8 @@ static void brcmusb_usb3_otp_fix(struct brcm_usb_init_params *params)
 	brcm_usb_writel(val, USB_XHCI_EC_REG(xhci_ec_base, IRADAT));
 
 	/* Reset USB 3.0 PHY for workaround to take effect */
-	USB_CTRL_UNSET(params->ctrl_regs, USB30_CTL1, PHY3_RESETB);
-	USB_CTRL_SET(params->ctrl_regs,	USB30_CTL1, PHY3_RESETB);
+	USB_CTRL_UNSET(params->regs[BRCM_REGS_CTRL], USB30_CTL1, PHY3_RESETB);
+	USB_CTRL_SET(params->regs[BRCM_REGS_CTRL], USB30_CTL1, PHY3_RESETB);
 }
 
 static void brcmusb_xhci_soft_reset(struct brcm_usb_init_params *params,
@@ -740,7 +740,7 @@ static enum brcm_family_type get_family_type(
 
 static void usb_init_ipp(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg;
 	u32 orig_reg;
 
@@ -786,7 +786,7 @@ static void usb_init_ipp(struct brcm_usb_init_params *params)
 static void usb_init_common(struct brcm_usb_init_params *params)
 {
 	u32 reg;
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	/* Clear any pending wake conditions */
 	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
@@ -866,7 +866,7 @@ static void usb_init_common(struct brcm_usb_init_params *params)
 static void usb_init_eohci(struct brcm_usb_init_params *params)
 {
 	u32 reg;
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	if (USB_CTRL_MASK_FAMILY(params, USB_PM, USB20_HC_RESETB))
 		USB_CTRL_SET_FAMILY(params, USB_PM, USB20_HC_RESETB);
@@ -902,7 +902,7 @@ static void usb_init_eohci(struct brcm_usb_init_params *params)
 
 static void usb_init_xhci(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	USB_CTRL_UNSET(ctrl, USB30_PCTL, PHY3_IDDQ_OVERRIDE);
 	/* 1 millisecond - for USB clocks to settle down */
@@ -944,12 +944,13 @@ static void usb_uninit_eohci(struct brcm_usb_init_params *params)
 static void usb_uninit_xhci(struct brcm_usb_init_params *params)
 {
 	brcmusb_xhci_soft_reset(params, 1);
-	USB_CTRL_SET(params->ctrl_regs, USB30_PCTL, PHY3_IDDQ_OVERRIDE);
+	USB_CTRL_SET(params->regs[BRCM_REGS_CTRL], USB30_PCTL,
+		     PHY3_IDDQ_OVERRIDE);
 }
 
 static int usb_get_dual_select(struct brcm_usb_init_params *params)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg = 0;
 
 	pr_debug("%s\n", __func__);
@@ -963,7 +964,7 @@ static int usb_get_dual_select(struct brcm_usb_init_params *params)
 
 static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	u32 reg;
 
 	pr_debug("%s\n", __func__);
@@ -980,7 +981,7 @@ static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 static void usb_wake_enable(struct brcm_usb_init_params *params,
 			  int enable)
 {
-	void __iomem *ctrl = params->ctrl_regs;
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	if (enable)
 		USB_CTRL_SET(ctrl, USB_PM, RMTWKUP_EN);
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index db6851c55335..2ea81daf295e 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -6,12 +6,21 @@
 #ifndef _USB_BRCM_COMMON_INIT_H
 #define _USB_BRCM_COMMON_INIT_H
 
+#include <linux/regmap.h>
+
 #define USB_CTLR_MODE_HOST 0
 #define USB_CTLR_MODE_DEVICE 1
 #define USB_CTLR_MODE_DRD 2
 #define USB_CTLR_MODE_TYPEC_PD 3
 
-struct  brcm_usb_init_params;
+enum brcmusb_reg_sel {
+	BRCM_REGS_CTRL = 0,
+	BRCM_REGS_XHCI_EC,
+	BRCM_REGS_XHCI_GBL,
+	BRCM_REGS_USB_PHY,
+	BRCM_REGS_USB_MDIO,
+	BRCM_REGS_MAX
+};
 
 #define USB_CTRL_REG(base, reg)	((void __iomem *)base + USB_CTRL_##reg)
 #define USB_XHCI_EC_REG(base, reg) ((void __iomem *)base + USB_XHCI_EC_##reg)
@@ -41,9 +50,7 @@ struct brcm_usb_init_ops {
 };
 
 struct  brcm_usb_init_params {
-	void __iomem *ctrl_regs;
-	void __iomem *xhci_ec_regs;
-	void __iomem *xhci_gbl_regs;
+	void __iomem *regs[BRCM_REGS_MAX];
 	int ioc;
 	int ipp;
 	int mode;
@@ -53,10 +60,12 @@ struct  brcm_usb_init_params {
 	const char *family_name;
 	const u32 *usb_reg_bits_map;
 	const struct brcm_usb_init_ops *ops;
+	struct regmap *syscon_piarbctl;
 };
 
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
 void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
+void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params);
 
 static inline u32 brcm_usb_readl(void __iomem *addr)
 {
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 64379ede480e..5f7bfa09494d 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -16,6 +16,7 @@
 #include <linux/interrupt.h>
 #include <linux/soc/brcmstb/brcmstb.h>
 #include <dt-bindings/phy/phy.h>
+#include <linux/mfd/syscon.h>
 
 #include "phy-brcm-usb-init.h"
 
@@ -32,6 +33,11 @@ struct value_to_name_map {
 	const char *name;
 };
 
+struct match_chip_info {
+	void *init_func;
+	u8 required_regs[BRCM_REGS_MAX + 1];
+};
+
 static struct value_to_name_map brcm_dr_mode_to_name[] = {
 	{ USB_CTLR_MODE_HOST, "host" },
 	{ USB_CTLR_MODE_DEVICE, "peripheral" },
@@ -64,6 +70,10 @@ struct brcm_usb_phy_data {
 	struct brcm_usb_phy	phys[BRCM_USB_PHY_ID_MAX];
 };
 
+static s8 *node_reg_names[BRCM_REGS_MAX] = {
+	"crtl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio"
+};
+
 static irqreturn_t brcm_usb_phy_wake_isr(int irq, void *dev_id)
 {
 	struct phy *gphy = dev_id;
@@ -241,15 +251,86 @@ static const struct attribute_group brcm_usb_phy_group = {
 	.attrs = brcm_usb_phy_attrs,
 };
 
+static struct match_chip_info chip_info_7216 = {
+	.init_func = &brcm_usb_dvr_init_7216,
+	.required_regs = {
+		BRCM_REGS_CTRL,
+		BRCM_REGS_XHCI_EC,
+		BRCM_REGS_XHCI_GBL,
+		-1,
+	},
+};
+
+static struct match_chip_info chip_info_7211b0 = {
+	.init_func = &brcm_usb_dvr_init_7211b0,
+	.required_regs = {
+		BRCM_REGS_CTRL,
+		BRCM_REGS_XHCI_EC,
+		BRCM_REGS_XHCI_GBL,
+		BRCM_REGS_USB_PHY,
+		BRCM_REGS_USB_MDIO,
+		-1,
+	},
+};
+
+static struct match_chip_info chip_info_7445 = {
+	.init_func = &brcm_usb_dvr_init_7445,
+	.required_regs = {
+		BRCM_REGS_CTRL,
+		BRCM_REGS_XHCI_EC,
+		-1,
+	},
+};
+
 static const struct of_device_id brcm_usb_dt_ids[] = {
 	{
 		.compatible = "brcm,bcm7216-usb-phy",
-		.data = &brcm_usb_dvr_init_7216,
+		.data = &chip_info_7216,
+	},
+	{
+		.compatible = "brcm,bcm7211-usb-phy",
+		.data = &chip_info_7211b0,
+	},
+	{
+		.compatible = "brcm,brcmstb-usb-phy",
+		.data = &chip_info_7445,
 	},
-	{ .compatible = "brcm,brcmstb-usb-phy" },
 	{ /* sentinel */ }
 };
 
+static int brcm_usb_get_regs(struct platform_device *pdev,
+			     enum brcmusb_reg_sel regs,
+			     struct  brcm_usb_init_params *ini)
+{
+	struct resource *res;
+
+	/* Older DT nodes have ctrl and optional xhci_ec by index only */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						node_reg_names[regs]);
+	if (res == NULL) {
+		if (regs == BRCM_REGS_CTRL) {
+			res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		} else if (regs == BRCM_REGS_XHCI_EC) {
+			res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+			/* XHCI_EC registers are optional */
+			if (res == NULL)
+				return 0;
+		}
+		if (res == NULL) {
+			dev_err(&pdev->dev, "can't get %s base address\n",
+				node_reg_names[regs]);
+			return 1;
+		}
+	}
+	ini->regs[regs] = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ini->regs[regs])) {
+		dev_err(&pdev->dev, "can't map %s register space\n",
+			node_reg_names[regs]);
+		return 1;
+	}
+	return 0;
+}
+
 static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 				 struct brcm_usb_phy_data *priv,
 				 struct device_node *dn)
@@ -325,9 +406,6 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 
 static int brcm_usb_phy_probe(struct platform_device *pdev)
 {
-	struct resource *res_ctrl;
-	struct resource *res_xhciec = NULL;
-	struct resource *res_xhcigbl = NULL;
 	struct device *dev = &pdev->dev;
 	struct brcm_usb_phy_data *priv;
 	struct phy_provider *phy_provider;
@@ -335,6 +413,10 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	int err;
 	const char *mode;
 	const struct of_device_id *match;
+	void (*dvr_init)(struct brcm_usb_init_params *params);
+	const struct match_chip_info *info;
+	struct regmap *rmap;
+	int x;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -345,58 +427,13 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	priv->ini.product_id = brcmstb_get_product_id();
 
 	match = of_match_node(brcm_usb_dt_ids, dev->of_node);
-	if (match && match->data) {
-		void (*dvr_init)(struct brcm_usb_init_params *params);
-
-		dvr_init = match->data;
-		(*dvr_init)(&priv->ini);
-	} else {
-		brcm_usb_dvr_init_7445(&priv->ini);
-	}
+	info = match->data;
+	dvr_init = info->init_func;
+	(*dvr_init)(&priv->ini);
 
 	dev_dbg(dev, "Best mapping table is for %s\n",
 		priv->ini.family_name);
 
-	/* Newer DT node has reg-names. xhci_ec and xhci_gbl are optional. */
-	res_ctrl = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
-	if (res_ctrl != NULL) {
-		res_xhciec = platform_get_resource_byname(pdev,
-							  IORESOURCE_MEM,
-							  "xhci_ec");
-		res_xhcigbl = platform_get_resource_byname(pdev,
-							   IORESOURCE_MEM,
-							   "xhci_gbl");
-	} else {
-		/* Older DT node without reg-names, use index */
-		res_ctrl = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-		if (res_ctrl == NULL) {
-			dev_err(dev, "can't get CTRL base address\n");
-			return -EINVAL;
-		}
-		res_xhciec = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	}
-	priv->ini.ctrl_regs = devm_ioremap_resource(dev, res_ctrl);
-	if (IS_ERR(priv->ini.ctrl_regs)) {
-		dev_err(dev, "can't map CTRL register space\n");
-		return -EINVAL;
-	}
-	if (res_xhciec) {
-		priv->ini.xhci_ec_regs =
-			devm_ioremap_resource(dev, res_xhciec);
-		if (IS_ERR(priv->ini.xhci_ec_regs)) {
-			dev_err(dev, "can't map XHCI EC register space\n");
-			return -EINVAL;
-		}
-	}
-	if (res_xhcigbl) {
-		priv->ini.xhci_gbl_regs =
-			devm_ioremap_resource(dev, res_xhcigbl);
-		if (IS_ERR(priv->ini.xhci_gbl_regs)) {
-			dev_err(dev, "can't map XHCI Global register space\n");
-			return -EINVAL;
-		}
-	}
-
 	of_property_read_u32(dn, "brcm,ipp", &priv->ini.ipp);
 	of_property_read_u32(dn, "brcm,ioc", &priv->ini.ioc);
 
@@ -412,6 +449,16 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	if (of_property_read_bool(dn, "brcm,has-eohci"))
 		priv->has_eohci = true;
 
+	for (x = 0; x < BRCM_REGS_MAX; x++) {
+		if (info->required_regs[x] >= BRCM_REGS_MAX)
+			break;
+
+		err = brcm_usb_get_regs(pdev, info->required_regs[x],
+					&priv->ini);
+		if (err)
+			return -EINVAL;
+	}
+
 	err = brcm_usb_phy_dvr_init(pdev, priv, dn);
 	if (err)
 		return err;
@@ -431,6 +478,15 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 	if (err)
 		dev_warn(dev, "Error creating sysfs attributes\n");
 
+	/* Get piarbctl syscon if it exists */
+	rmap = syscon_regmap_lookup_by_phandle(dev->of_node,
+						 "syscon-piarbctl");
+	if (IS_ERR(rmap))
+		rmap = syscon_regmap_lookup_by_phandle(dev->of_node,
+						       "brcm,syscon-piarbctl");
+	if (!IS_ERR(rmap))
+		priv->ini.syscon_piarbctl = rmap;
+
 	/* start with everything off */
 	if (priv->has_xhci)
 		brcm_usb_uninit_xhci(&priv->ini);
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 09/13] phy: usb: fix driver to defer on clk_get defer

[Al Cooper]

Handle defer on clk_get because the new SCMI clock driver comes
up after this driver.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 5f7bfa09494d..c82d7ec15334 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -341,6 +341,8 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 
 	priv->usb_20_clk = of_clk_get_by_name(dn, "sw_usb");
 	if (IS_ERR(priv->usb_20_clk)) {
+		if (PTR_ERR(priv->usb_20_clk) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
 		dev_info(dev, "Clock not found in Device Tree\n");
 		priv->usb_20_clk = NULL;
 	}
@@ -371,6 +373,8 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 
 		priv->usb_30_clk = of_clk_get_by_name(dn, "sw_usb3");
 		if (IS_ERR(priv->usb_30_clk)) {
+			if (PTR_ERR(priv->usb_30_clk) == -EPROBE_DEFER)
+				return -EPROBE_DEFER;
 			dev_info(dev,
 				 "USB3.0 clock not found in Device Tree\n");
 			priv->usb_30_clk = NULL;
@@ -382,6 +386,8 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 
 	priv->suspend_clk = clk_get(dev, "usb0_freerun");
 	if (IS_ERR(priv->suspend_clk)) {
+		if (PTR_ERR(priv->suspend_clk) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
 		dev_err(dev, "Suspend Clock not found in Device Tree\n");
 		priv->suspend_clk = NULL;
 	}
-- 
2.17.1

[PATCH v3 09/13] phy: usb: fix driver to defer on clk_get defer

[Al Cooper]

Handle defer on clk_get because the new SCMI clock driver comes
up after this driver.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 5f7bfa09494d..c82d7ec15334 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -341,6 +341,8 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 
 	priv->usb_20_clk = of_clk_get_by_name(dn, "sw_usb");
 	if (IS_ERR(priv->usb_20_clk)) {
+		if (PTR_ERR(priv->usb_20_clk) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
 		dev_info(dev, "Clock not found in Device Tree\n");
 		priv->usb_20_clk = NULL;
 	}
@@ -371,6 +373,8 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 
 		priv->usb_30_clk = of_clk_get_by_name(dn, "sw_usb3");
 		if (IS_ERR(priv->usb_30_clk)) {
+			if (PTR_ERR(priv->usb_30_clk) == -EPROBE_DEFER)
+				return -EPROBE_DEFER;
 			dev_info(dev,
 				 "USB3.0 clock not found in Device Tree\n");
 			priv->usb_30_clk = NULL;
@@ -382,6 +386,8 @@ static int brcm_usb_phy_dvr_init(struct platform_device *pdev,
 
 	priv->suspend_clk = clk_get(dev, "usb0_freerun");
 	if (IS_ERR(priv->suspend_clk)) {
+		if (PTR_ERR(priv->suspend_clk) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
 		dev_err(dev, "Suspend Clock not found in Device Tree\n");
 		priv->suspend_clk = NULL;
 	}
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 10/13] phy: usb: PHY's MDIO registers not accessible without device installed

[Al Cooper]

When there is no device connected and FSM is enabled, the XHCI puts
the PHY into suspend mode.  When the PHY is put into suspend mode
the USB LDO powers down the PHY. This causes the MDIO to be
inaccessible and its registers reset to default. The fix is to
disable FSM.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
index bf138867efb1..fe3f653c64a7 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -56,6 +56,7 @@
 #define USB_PHY_PLL_LDO_CTL		0x08
 #define   USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK		0x00000004
 #define USB_PHY_UTMI_CTL_1		0x04
+#define   USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK	0x00000800
 #define   USB_PHY_UTMI_CTL_1_PHY_MODE_MASK		0x0000000c
 #define   USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT		2
 #define USB_PHY_STATUS			0x20
@@ -229,6 +230,14 @@ static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 
 	usb_init_common(params);
 
+	/*
+	 * Disable FSM, otherwise the PHY will auto suspend when no
+	 * device is connected and will be reset on resume.
+	 */
+	reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
+	reg &= ~USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK;
+	brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
+
 	usb2_eye_fix_7211b0(params);
 }
 
-- 
2.17.1

[PATCH v3 10/13] phy: usb: PHY's MDIO registers not accessible without device installed

[Al Cooper]

When there is no device connected and FSM is enabled, the XHCI puts
the PHY into suspend mode.  When the PHY is put into suspend mode
the USB LDO powers down the PHY. This causes the MDIO to be
inaccessible and its registers reset to default. The fix is to
disable FSM.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
index bf138867efb1..fe3f653c64a7 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -56,6 +56,7 @@
 #define USB_PHY_PLL_LDO_CTL		0x08
 #define   USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK		0x00000004
 #define USB_PHY_UTMI_CTL_1		0x04
+#define   USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK	0x00000800
 #define   USB_PHY_UTMI_CTL_1_PHY_MODE_MASK		0x0000000c
 #define   USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT		2
 #define USB_PHY_STATUS			0x20
@@ -229,6 +230,14 @@ static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 
 	usb_init_common(params);
 
+	/*
+	 * Disable FSM, otherwise the PHY will auto suspend when no
+	 * device is connected and will be reset on resume.
+	 */
+	reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
+	reg &= ~USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK;
+	brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
+
 	usb2_eye_fix_7211b0(params);
 }
 
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 11/13] phy: usb: bdc: Fix occasional failure with BDC on 7211

[Al Cooper]

The BDC "Read Transaction Size" needs to be changed from 1024
bytes to 256 bytes to prevent occasional transaction failures.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 18 +++++++++++++++
 drivers/phy/broadcom/phy-brcm-usb-init.h      |  1 +
 drivers/phy/broadcom/phy-brcm-usb.c           | 23 +++++++++++++++----
 3 files changed, 38 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
index fe3f653c64a7..c6504649d307 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -70,6 +70,11 @@
 #define USB_GMDIOCSR	0
 #define USB_GMDIOGEN	4
 
+/* Register definitions for the BDC EC block in 7211b0 */
+#define BDC_EC_AXIRDA			0x0c
+#define   BDC_EC_AXIRDA_RTS_MASK			0xf0000000
+#define   BDC_EC_AXIRDA_RTS_SHIFT			28
+
 
 static void usb_mdio_write_7211b0(struct brcm_usb_init_params *params,
 				  uint8_t addr, uint16_t data)
@@ -198,6 +203,7 @@ static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
+	void __iomem *bdc_ec = params->regs[BRCM_REGS_BDC_EC];
 	int timeout_ms = PHY_LOCK_TIMEOUT_MS;
 	u32 reg;
 
@@ -230,6 +236,18 @@ static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 
 	usb_init_common(params);
 
+	/*
+	 * The BDC controller will get occasional failures with
+	 * the default "Read Transaction Size" of 6 (1024 bytes).
+	 * Set it to 4 (256 bytes).
+	 */
+	if ((params->mode != USB_CTLR_MODE_HOST) && bdc_ec) {
+		reg = brcm_usb_readl(bdc_ec + BDC_EC_AXIRDA);
+		reg &= ~BDC_EC_AXIRDA_RTS_MASK;
+		reg |= (0x4 << BDC_EC_AXIRDA_RTS_SHIFT);
+		brcm_usb_writel(reg, bdc_ec + BDC_EC_AXIRDA);
+	}
+
 	/*
 	 * Disable FSM, otherwise the PHY will auto suspend when no
 	 * device is connected and will be reset on resume.
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index 2ea81daf295e..4cdd9cc1c5a3 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -19,6 +19,7 @@ enum brcmusb_reg_sel {
 	BRCM_REGS_XHCI_GBL,
 	BRCM_REGS_USB_PHY,
 	BRCM_REGS_USB_MDIO,
+	BRCM_REGS_BDC_EC,
 	BRCM_REGS_MAX
 };
 
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index c82d7ec15334..cc5763ace3ad 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -36,6 +36,7 @@ struct value_to_name_map {
 struct match_chip_info {
 	void *init_func;
 	u8 required_regs[BRCM_REGS_MAX + 1];
+	u8 optional_reg;
 };
 
 static struct value_to_name_map brcm_dr_mode_to_name[] = {
@@ -71,7 +72,7 @@ struct brcm_usb_phy_data {
 };
 
 static s8 *node_reg_names[BRCM_REGS_MAX] = {
-	"crtl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio"
+	"crtl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio", "bdc_ec"
 };
 
 static irqreturn_t brcm_usb_phy_wake_isr(int irq, void *dev_id)
@@ -271,6 +272,7 @@ static struct match_chip_info chip_info_7211b0 = {
 		BRCM_REGS_USB_MDIO,
 		-1,
 	},
+	.optional_reg = BRCM_REGS_BDC_EC,
 };
 
 static struct match_chip_info chip_info_7445 = {
@@ -300,7 +302,8 @@ static const struct of_device_id brcm_usb_dt_ids[] = {
 
 static int brcm_usb_get_regs(struct platform_device *pdev,
 			     enum brcmusb_reg_sel regs,
-			     struct  brcm_usb_init_params *ini)
+			     struct  brcm_usb_init_params *ini,
+			     bool optional)
 {
 	struct resource *res;
 
@@ -317,7 +320,13 @@ static int brcm_usb_get_regs(struct platform_device *pdev,
 				return 0;
 		}
 		if (res == NULL) {
-			dev_err(&pdev->dev, "can't get %s base address\n",
+			if (optional) {
+				dev_dbg(&pdev->dev,
+					"Optional reg %s not found\n",
+					node_reg_names[regs]);
+				return 0;
+			}
+			dev_err(&pdev->dev, "can't get %s base addr\n",
 				node_reg_names[regs]);
 			return 1;
 		}
@@ -460,7 +469,13 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 			break;
 
 		err = brcm_usb_get_regs(pdev, info->required_regs[x],
-					&priv->ini);
+					&priv->ini, false);
+		if (err)
+			return -EINVAL;
+	}
+	if (info->optional_reg) {
+		err = brcm_usb_get_regs(pdev, info->optional_reg,
+					&priv->ini, true);
 		if (err)
 			return -EINVAL;
 	}
-- 
2.17.1

[PATCH v3 11/13] phy: usb: bdc: Fix occasional failure with BDC on 7211

[Al Cooper]

The BDC "Read Transaction Size" needs to be changed from 1024
bytes to 256 bytes to prevent occasional transaction failures.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 18 +++++++++++++++
 drivers/phy/broadcom/phy-brcm-usb-init.h      |  1 +
 drivers/phy/broadcom/phy-brcm-usb.c           | 23 +++++++++++++++----
 3 files changed, 38 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
index fe3f653c64a7..c6504649d307 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -70,6 +70,11 @@
 #define USB_GMDIOCSR	0
 #define USB_GMDIOGEN	4
 
+/* Register definitions for the BDC EC block in 7211b0 */
+#define BDC_EC_AXIRDA			0x0c
+#define   BDC_EC_AXIRDA_RTS_MASK			0xf0000000
+#define   BDC_EC_AXIRDA_RTS_SHIFT			28
+
 
 static void usb_mdio_write_7211b0(struct brcm_usb_init_params *params,
 				  uint8_t addr, uint16_t data)
@@ -198,6 +203,7 @@ static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 	void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
+	void __iomem *bdc_ec = params->regs[BRCM_REGS_BDC_EC];
 	int timeout_ms = PHY_LOCK_TIMEOUT_MS;
 	u32 reg;
 
@@ -230,6 +236,18 @@ static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 
 	usb_init_common(params);
 
+	/*
+	 * The BDC controller will get occasional failures with
+	 * the default "Read Transaction Size" of 6 (1024 bytes).
+	 * Set it to 4 (256 bytes).
+	 */
+	if ((params->mode != USB_CTLR_MODE_HOST) && bdc_ec) {
+		reg = brcm_usb_readl(bdc_ec + BDC_EC_AXIRDA);
+		reg &= ~BDC_EC_AXIRDA_RTS_MASK;
+		reg |= (0x4 << BDC_EC_AXIRDA_RTS_SHIFT);
+		brcm_usb_writel(reg, bdc_ec + BDC_EC_AXIRDA);
+	}
+
 	/*
 	 * Disable FSM, otherwise the PHY will auto suspend when no
 	 * device is connected and will be reset on resume.
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index 2ea81daf295e..4cdd9cc1c5a3 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -19,6 +19,7 @@ enum brcmusb_reg_sel {
 	BRCM_REGS_XHCI_GBL,
 	BRCM_REGS_USB_PHY,
 	BRCM_REGS_USB_MDIO,
+	BRCM_REGS_BDC_EC,
 	BRCM_REGS_MAX
 };
 
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index c82d7ec15334..cc5763ace3ad 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -36,6 +36,7 @@ struct value_to_name_map {
 struct match_chip_info {
 	void *init_func;
 	u8 required_regs[BRCM_REGS_MAX + 1];
+	u8 optional_reg;
 };
 
 static struct value_to_name_map brcm_dr_mode_to_name[] = {
@@ -71,7 +72,7 @@ struct brcm_usb_phy_data {
 };
 
 static s8 *node_reg_names[BRCM_REGS_MAX] = {
-	"crtl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio"
+	"crtl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio", "bdc_ec"
 };
 
 static irqreturn_t brcm_usb_phy_wake_isr(int irq, void *dev_id)
@@ -271,6 +272,7 @@ static struct match_chip_info chip_info_7211b0 = {
 		BRCM_REGS_USB_MDIO,
 		-1,
 	},
+	.optional_reg = BRCM_REGS_BDC_EC,
 };
 
 static struct match_chip_info chip_info_7445 = {
@@ -300,7 +302,8 @@ static const struct of_device_id brcm_usb_dt_ids[] = {
 
 static int brcm_usb_get_regs(struct platform_device *pdev,
 			     enum brcmusb_reg_sel regs,
-			     struct  brcm_usb_init_params *ini)
+			     struct  brcm_usb_init_params *ini,
+			     bool optional)
 {
 	struct resource *res;
 
@@ -317,7 +320,13 @@ static int brcm_usb_get_regs(struct platform_device *pdev,
 				return 0;
 		}
 		if (res == NULL) {
-			dev_err(&pdev->dev, "can't get %s base address\n",
+			if (optional) {
+				dev_dbg(&pdev->dev,
+					"Optional reg %s not found\n",
+					node_reg_names[regs]);
+				return 0;
+			}
+			dev_err(&pdev->dev, "can't get %s base addr\n",
 				node_reg_names[regs]);
 			return 1;
 		}
@@ -460,7 +469,13 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
 			break;
 
 		err = brcm_usb_get_regs(pdev, info->required_regs[x],
-					&priv->ini);
+					&priv->ini, false);
+		if (err)
+			return -EINVAL;
+	}
+	if (info->optional_reg) {
+		err = brcm_usb_get_regs(pdev, info->optional_reg,
+					&priv->ini, true);
 		if (err)
 			return -EINVAL;
 	}
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 12/13] phy: usb: USB driver is crashing during S3 resume on 7216

[Al Cooper]

This is a result of the USB 2.0 clocks not being disabled/enabled
during suspend/resume on XHCI only systems.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index cc5763ace3ad..1ab44f54244b 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -543,7 +543,7 @@ static int brcm_usb_phy_suspend(struct device *dev)
 		brcm_usb_wake_enable(&priv->ini, true);
 		if (priv->phys[BRCM_USB_PHY_3_0].inited)
 			clk_disable_unprepare(priv->usb_30_clk);
-		if (priv->phys[BRCM_USB_PHY_2_0].inited)
+		if (priv->phys[BRCM_USB_PHY_2_0].inited || !priv->has_eohci)
 			clk_disable_unprepare(priv->usb_20_clk);
 		if (priv->wake_irq >= 0)
 			enable_irq_wake(priv->wake_irq);
-- 
2.17.1

[PATCH v3 12/13] phy: usb: USB driver is crashing during S3 resume on 7216

[Al Cooper]

This is a result of the USB 2.0 clocks not being disabled/enabled
during suspend/resume on XHCI only systems.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 drivers/phy/broadcom/phy-brcm-usb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index cc5763ace3ad..1ab44f54244b 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -543,7 +543,7 @@ static int brcm_usb_phy_suspend(struct device *dev)
 		brcm_usb_wake_enable(&priv->ini, true);
 		if (priv->phys[BRCM_USB_PHY_3_0].inited)
 			clk_disable_unprepare(priv->usb_30_clk);
-		if (priv->phys[BRCM_USB_PHY_2_0].inited)
+		if (priv->phys[BRCM_USB_PHY_2_0].inited || !priv->has_eohci)
 			clk_disable_unprepare(priv->usb_20_clk);
 		if (priv->wake_irq >= 0)
 			enable_irq_wake(priv->wake_irq);
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 13/13] phy: usb: Add support for wake and USB low power mode for 7211 S2/S5

[Al Cooper]

Add support for 7211 USB wake. Disable all possible 7211 USB logic
for S2/S5 if USB wake is not enabled.

On the 7211, the XHCI wake signal was not connected properly and
only goes to the USB1_USB1_CTRL_TP_DIAG1 diagonstic register.
The workaround is to have VPU code running that polls for the
proper bit in the DIAG register and to wake the system when
the bit is asserted.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 77 +++++++++++++++++--
 drivers/phy/broadcom/phy-brcm-usb-init.c      | 26 ++++---
 drivers/phy/broadcom/phy-brcm-usb-init.h      | 11 +--
 drivers/phy/broadcom/phy-brcm-usb.c           | 25 ++++--
 4 files changed, 105 insertions(+), 34 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
index c6504649d307..a2f96fce8c2f 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -26,7 +26,6 @@
 #define   PIARBCTL_MISC_CAM1_MEM_PAGE_MASK		0x00000f00
 #define   PIARBCTL_MISC_CAM0_MEM_PAGE_MASK		0x000000f0
 #define   PIARBCTL_MISC_SATA_PRIORITY_MASK		0x0000000f
-#define PIARBCTL_USB_M_ASB_CTRL		0x10
 
 #define PIARBCTL_MISC_USB_ONLY_MASK		\
 	(PIARBCTL_MISC_USB_SELECT_MASK |	\
@@ -51,14 +50,27 @@
 #define USB_CTRL_USB_PM_STATUS		0x08
 #define USB_CTRL_USB_DEVICE_CTL1	0x10
 #define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK	0x00000003
+#define USB_CTRL_TEST_PORT_CTL		0x30
+#define   USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_MASK	0x000000ff
+#define   USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_PME_GEN_MASK	0x0000002e
+#define USB_CTRL_TP_DIAG1		0x34
+#define   USB_CTLR_TP_DIAG1_wake_MASK	0x00000002
+#define USB_CTRL_CTLR_CSHCR		0x50
+#define   USB_CTRL_CTLR_CSHCR_ctl_pme_en_MASK	0x00040000
 
 /* Register definitions for the USB_PHY block in 7211b0 */
+#define USB_PHY_PLL_CTL			0x00
+#define   USB_PHY_PLL_CTL_PLL_RESETB_MASK		0x40000000
 #define USB_PHY_PLL_LDO_CTL		0x08
 #define   USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK		0x00000004
+#define   USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK	0x00000002
+#define   USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK	0x00000001
 #define USB_PHY_UTMI_CTL_1		0x04
 #define   USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK	0x00000800
 #define   USB_PHY_UTMI_CTL_1_PHY_MODE_MASK		0x0000000c
 #define   USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT		2
+#define USB_PHY_IDDQ			0x1c
+#define   USB_PHY_IDDQ_phy_iddq_MASK			0x00000001
 #define USB_PHY_STATUS			0x20
 #define   USB_PHY_STATUS_pll_lock_MASK			0x00000001
 
@@ -199,6 +211,17 @@ static void usb_init_common(struct brcm_usb_init_params *params)
 	}
 }
 
+static void usb_wake_enable_7211b0(struct brcm_usb_init_params *params,
+				   bool enable)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+
+	if (enable)
+		USB_CTRL_SET(ctrl, CTLR_CSHCR, ctl_pme_en);
+	else
+		USB_CTRL_UNSET(ctrl, CTLR_CSHCR, ctl_pme_en);
+}
+
 static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
@@ -210,9 +233,27 @@ static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 	if (params->syscon_piarbctl)
 		syscon_piarbctl_init(params->syscon_piarbctl);
 
+	USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
+
+	usb_wake_enable_7211b0(params, false);
+	if (!params->wake_enabled) {
+
+		/* undo possible suspend settings */
+		brcm_usb_writel(0, usb_phy + USB_PHY_IDDQ);
+		reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
+		reg |= USB_PHY_PLL_CTL_PLL_RESETB_MASK;
+		brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
+
+		/* temporarily enable FSM so PHY comes up properly */
+		reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
+		reg |= USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK;
+		brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
+	}
+
 	/* Init the PHY */
-	reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_LDO_CTL);
-	reg |= USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK;
+	reg = USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK |
+		USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK |
+		USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK;
 	brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_LDO_CTL);
 
 	/* wait for lock */
@@ -276,12 +317,36 @@ static void usb_uninit_common(struct brcm_usb_init_params *params)
 
 }
 
+static void usb_uninit_common_7211b0(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+	void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
+	u32 reg;
+
+	pr_debug("%s\n", __func__);
+
+	if (params->wake_enabled) {
+		USB_CTRL_SET(ctrl, TEST_PORT_CTL, TPOUT_SEL_PME_GEN);
+		usb_wake_enable_7211b0(params, true);
+	} else {
+		USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
+		brcm_usb_writel(0, usb_phy + USB_PHY_PLL_LDO_CTL);
+		reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
+		reg &= ~USB_PHY_PLL_CTL_PLL_RESETB_MASK;
+		brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
+		brcm_usb_writel(USB_PHY_IDDQ_phy_iddq_MASK,
+				usb_phy + USB_PHY_IDDQ);
+	}
+
+}
+
 static void usb_uninit_xhci(struct brcm_usb_init_params *params)
 {
 
 	pr_debug("%s\n", __func__);
 
-	xhci_soft_reset(params, 1);
+	if (!params->wake_enabled)
+		xhci_soft_reset(params, 1);
 }
 
 static int usb_get_dual_select(struct brcm_usb_init_params *params)
@@ -309,7 +374,6 @@ static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
 }
 
-
 static const struct brcm_usb_init_ops bcm7216_ops = {
 	.init_ipp = usb_init_ipp,
 	.init_common = usb_init_common,
@@ -324,7 +388,7 @@ static const struct brcm_usb_init_ops bcm7211b0_ops = {
 	.init_ipp = usb_init_ipp,
 	.init_common = usb_init_common_7211b0,
 	.init_xhci = usb_init_xhci,
-	.uninit_common = usb_uninit_common,
+	.uninit_common = usb_uninit_common_7211b0,
 	.uninit_xhci = usb_uninit_xhci,
 	.get_dual_select = usb_get_dual_select,
 	.set_dual_select = usb_set_dual_select,
@@ -346,4 +410,5 @@ void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params)
 
 	params->family_name = "7211";
 	params->ops = &bcm7211b0_ops;
+	params->suspend_with_clocks = true;
 }
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index 17acc3c1051b..9391ab42a12b 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -783,12 +783,24 @@ static void usb_init_ipp(struct brcm_usb_init_params *params)
 		msleep(50);
 }
 
+static void usb_wake_enable(struct brcm_usb_init_params *params,
+			  bool enable)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+
+	if (enable)
+		USB_CTRL_SET(ctrl, USB_PM, RMTWKUP_EN);
+	else
+		USB_CTRL_UNSET(ctrl, USB_PM, RMTWKUP_EN);
+}
+
 static void usb_init_common(struct brcm_usb_init_params *params)
 {
 	u32 reg;
 	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	/* Clear any pending wake conditions */
+	usb_wake_enable(params, false);
 	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
 	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_PM_STATUS));
 
@@ -935,6 +947,8 @@ static void usb_uninit_common(struct brcm_usb_init_params *params)
 
 	if (USB_CTRL_MASK_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN))
 		USB_CTRL_SET_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN);
+	if (params->wake_enabled)
+		usb_wake_enable(params, true);
 }
 
 static void usb_uninit_eohci(struct brcm_usb_init_params *params)
@@ -978,17 +992,6 @@ static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 	}
 }
 
-static void usb_wake_enable(struct brcm_usb_init_params *params,
-			  int enable)
-{
-	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
-
-	if (enable)
-		USB_CTRL_SET(ctrl, USB_PM, RMTWKUP_EN);
-	else
-		USB_CTRL_UNSET(ctrl, USB_PM, RMTWKUP_EN);
-}
-
 static const struct brcm_usb_init_ops bcm7445_ops = {
 	.init_ipp = usb_init_ipp,
 	.init_common = usb_init_common,
@@ -999,7 +1002,6 @@ static const struct brcm_usb_init_ops bcm7445_ops = {
 	.uninit_xhci = usb_uninit_xhci,
 	.get_dual_select = usb_get_dual_select,
 	.set_dual_select = usb_set_dual_select,
-	.wake_enable = usb_wake_enable,
 };
 
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params)
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index 4cdd9cc1c5a3..899b9eb43fad 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -46,8 +46,6 @@ struct brcm_usb_init_ops {
 	void (*uninit_xhci)(struct brcm_usb_init_params *params);
 	int  (*get_dual_select)(struct brcm_usb_init_params *params);
 	void (*set_dual_select)(struct brcm_usb_init_params *params, int mode);
-	void (*wake_enable)(struct brcm_usb_init_params *params,
-			    int enable);
 };
 
 struct  brcm_usb_init_params {
@@ -62,6 +60,8 @@ struct  brcm_usb_init_params {
 	const u32 *usb_reg_bits_map;
 	const struct brcm_usb_init_ops *ops;
 	struct regmap *syscon_piarbctl;
+	bool wake_enabled;
+	bool suspend_with_clocks;
 };
 
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
@@ -145,13 +145,6 @@ static inline void brcm_usb_uninit_xhci(struct brcm_usb_init_params *ini)
 		ini->ops->uninit_xhci(ini);
 }
 
-static inline void brcm_usb_wake_enable(struct brcm_usb_init_params *ini,
-	int enable)
-{
-	if (ini->ops->wake_enable)
-		ini->ops->wake_enable(ini, enable);
-}
-
 static inline int brcm_usb_get_dual_select(struct brcm_usb_init_params *ini)
 {
 	if (ini->ops->get_dual_select)
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 1ab44f54244b..491bbd46c5b3 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -535,16 +535,26 @@ static int brcm_usb_phy_suspend(struct device *dev)
 	struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
 
 	if (priv->init_count) {
+		priv->ini.wake_enabled = device_may_wakeup(dev);
 		if (priv->phys[BRCM_USB_PHY_3_0].inited)
 			brcm_usb_uninit_xhci(&priv->ini);
 		if (priv->phys[BRCM_USB_PHY_2_0].inited)
 			brcm_usb_uninit_eohci(&priv->ini);
 		brcm_usb_uninit_common(&priv->ini);
-		brcm_usb_wake_enable(&priv->ini, true);
-		if (priv->phys[BRCM_USB_PHY_3_0].inited)
-			clk_disable_unprepare(priv->usb_30_clk);
-		if (priv->phys[BRCM_USB_PHY_2_0].inited || !priv->has_eohci)
-			clk_disable_unprepare(priv->usb_20_clk);
+
+		/*
+		 * Handle the clocks unless needed for wake. This has
+		 * to work for both older XHCI->3.0-clks, EOHCI->2.0-clks
+		 * and newer XHCI->2.0-clks/3.0-clks.
+		 */
+
+		if (!priv->ini.suspend_with_clocks) {
+			if (priv->phys[BRCM_USB_PHY_3_0].inited)
+				clk_disable_unprepare(priv->usb_30_clk);
+			if (priv->phys[BRCM_USB_PHY_2_0].inited ||
+			    !priv->has_eohci)
+				clk_disable_unprepare(priv->usb_20_clk);
+		}
 		if (priv->wake_irq >= 0)
 			enable_irq_wake(priv->wake_irq);
 	}
@@ -557,7 +567,6 @@ static int brcm_usb_phy_resume(struct device *dev)
 
 	clk_prepare_enable(priv->usb_20_clk);
 	clk_prepare_enable(priv->usb_30_clk);
-	brcm_usb_wake_enable(&priv->ini, false);
 	brcm_usb_init_ipp(&priv->ini);
 
 	/*
@@ -579,6 +588,8 @@ static int brcm_usb_phy_resume(struct device *dev)
 		} else if (priv->has_xhci) {
 			brcm_usb_uninit_xhci(&priv->ini);
 			clk_disable_unprepare(priv->usb_30_clk);
+			if (!priv->has_eohci)
+				clk_disable_unprepare(priv->usb_20_clk);
 		}
 	} else {
 		if (priv->has_xhci)
@@ -589,7 +600,7 @@ static int brcm_usb_phy_resume(struct device *dev)
 		clk_disable_unprepare(priv->usb_20_clk);
 		clk_disable_unprepare(priv->usb_30_clk);
 	}
-
+	priv->ini.wake_enabled = false;
 	return 0;
 }
 #endif /* CONFIG_PM_SLEEP */
-- 
2.17.1

[PATCH v3 13/13] phy: usb: Add support for wake and USB low power mode for 7211 S2/S5

[Al Cooper]

Add support for 7211 USB wake. Disable all possible 7211 USB logic
for S2/S5 if USB wake is not enabled.

On the 7211, the XHCI wake signal was not connected properly and
only goes to the USB1_USB1_CTRL_TP_DIAG1 diagonstic register.
The workaround is to have VPU code running that polls for the
proper bit in the DIAG register and to wake the system when
the bit is asserted.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
---
 .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 77 +++++++++++++++++--
 drivers/phy/broadcom/phy-brcm-usb-init.c      | 26 ++++---
 drivers/phy/broadcom/phy-brcm-usb-init.h      | 11 +--
 drivers/phy/broadcom/phy-brcm-usb.c           | 25 ++++--
 4 files changed, 105 insertions(+), 34 deletions(-)

diff --git a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
index c6504649d307..a2f96fce8c2f 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
@@ -26,7 +26,6 @@
 #define   PIARBCTL_MISC_CAM1_MEM_PAGE_MASK		0x00000f00
 #define   PIARBCTL_MISC_CAM0_MEM_PAGE_MASK		0x000000f0
 #define   PIARBCTL_MISC_SATA_PRIORITY_MASK		0x0000000f
-#define PIARBCTL_USB_M_ASB_CTRL		0x10
 
 #define PIARBCTL_MISC_USB_ONLY_MASK		\
 	(PIARBCTL_MISC_USB_SELECT_MASK |	\
@@ -51,14 +50,27 @@
 #define USB_CTRL_USB_PM_STATUS		0x08
 #define USB_CTRL_USB_DEVICE_CTL1	0x10
 #define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK	0x00000003
+#define USB_CTRL_TEST_PORT_CTL		0x30
+#define   USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_MASK	0x000000ff
+#define   USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_PME_GEN_MASK	0x0000002e
+#define USB_CTRL_TP_DIAG1		0x34
+#define   USB_CTLR_TP_DIAG1_wake_MASK	0x00000002
+#define USB_CTRL_CTLR_CSHCR		0x50
+#define   USB_CTRL_CTLR_CSHCR_ctl_pme_en_MASK	0x00040000
 
 /* Register definitions for the USB_PHY block in 7211b0 */
+#define USB_PHY_PLL_CTL			0x00
+#define   USB_PHY_PLL_CTL_PLL_RESETB_MASK		0x40000000
 #define USB_PHY_PLL_LDO_CTL		0x08
 #define   USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK		0x00000004
+#define   USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK	0x00000002
+#define   USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK	0x00000001
 #define USB_PHY_UTMI_CTL_1		0x04
 #define   USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK	0x00000800
 #define   USB_PHY_UTMI_CTL_1_PHY_MODE_MASK		0x0000000c
 #define   USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT		2
+#define USB_PHY_IDDQ			0x1c
+#define   USB_PHY_IDDQ_phy_iddq_MASK			0x00000001
 #define USB_PHY_STATUS			0x20
 #define   USB_PHY_STATUS_pll_lock_MASK			0x00000001
 
@@ -199,6 +211,17 @@ static void usb_init_common(struct brcm_usb_init_params *params)
 	}
 }
 
+static void usb_wake_enable_7211b0(struct brcm_usb_init_params *params,
+				   bool enable)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+
+	if (enable)
+		USB_CTRL_SET(ctrl, CTLR_CSHCR, ctl_pme_en);
+	else
+		USB_CTRL_UNSET(ctrl, CTLR_CSHCR, ctl_pme_en);
+}
+
 static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
@@ -210,9 +233,27 @@ static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 	if (params->syscon_piarbctl)
 		syscon_piarbctl_init(params->syscon_piarbctl);
 
+	USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
+
+	usb_wake_enable_7211b0(params, false);
+	if (!params->wake_enabled) {
+
+		/* undo possible suspend settings */
+		brcm_usb_writel(0, usb_phy + USB_PHY_IDDQ);
+		reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
+		reg |= USB_PHY_PLL_CTL_PLL_RESETB_MASK;
+		brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
+
+		/* temporarily enable FSM so PHY comes up properly */
+		reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
+		reg |= USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK;
+		brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
+	}
+
 	/* Init the PHY */
-	reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_LDO_CTL);
-	reg |= USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK;
+	reg = USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK |
+		USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK |
+		USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK;
 	brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_LDO_CTL);
 
 	/* wait for lock */
@@ -276,12 +317,36 @@ static void usb_uninit_common(struct brcm_usb_init_params *params)
 
 }
 
+static void usb_uninit_common_7211b0(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+	void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
+	u32 reg;
+
+	pr_debug("%s\n", __func__);
+
+	if (params->wake_enabled) {
+		USB_CTRL_SET(ctrl, TEST_PORT_CTL, TPOUT_SEL_PME_GEN);
+		usb_wake_enable_7211b0(params, true);
+	} else {
+		USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
+		brcm_usb_writel(0, usb_phy + USB_PHY_PLL_LDO_CTL);
+		reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
+		reg &= ~USB_PHY_PLL_CTL_PLL_RESETB_MASK;
+		brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
+		brcm_usb_writel(USB_PHY_IDDQ_phy_iddq_MASK,
+				usb_phy + USB_PHY_IDDQ);
+	}
+
+}
+
 static void usb_uninit_xhci(struct brcm_usb_init_params *params)
 {
 
 	pr_debug("%s\n", __func__);
 
-	xhci_soft_reset(params, 1);
+	if (!params->wake_enabled)
+		xhci_soft_reset(params, 1);
 }
 
 static int usb_get_dual_select(struct brcm_usb_init_params *params)
@@ -309,7 +374,6 @@ static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
 }
 
-
 static const struct brcm_usb_init_ops bcm7216_ops = {
 	.init_ipp = usb_init_ipp,
 	.init_common = usb_init_common,
@@ -324,7 +388,7 @@ static const struct brcm_usb_init_ops bcm7211b0_ops = {
 	.init_ipp = usb_init_ipp,
 	.init_common = usb_init_common_7211b0,
 	.init_xhci = usb_init_xhci,
-	.uninit_common = usb_uninit_common,
+	.uninit_common = usb_uninit_common_7211b0,
 	.uninit_xhci = usb_uninit_xhci,
 	.get_dual_select = usb_get_dual_select,
 	.set_dual_select = usb_set_dual_select,
@@ -346,4 +410,5 @@ void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params)
 
 	params->family_name = "7211";
 	params->ops = &bcm7211b0_ops;
+	params->suspend_with_clocks = true;
 }
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c
index 17acc3c1051b..9391ab42a12b 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.c
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.c
@@ -783,12 +783,24 @@ static void usb_init_ipp(struct brcm_usb_init_params *params)
 		msleep(50);
 }
 
+static void usb_wake_enable(struct brcm_usb_init_params *params,
+			  bool enable)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+
+	if (enable)
+		USB_CTRL_SET(ctrl, USB_PM, RMTWKUP_EN);
+	else
+		USB_CTRL_UNSET(ctrl, USB_PM, RMTWKUP_EN);
+}
+
 static void usb_init_common(struct brcm_usb_init_params *params)
 {
 	u32 reg;
 	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	/* Clear any pending wake conditions */
+	usb_wake_enable(params, false);
 	reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_PM_STATUS));
 	brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_PM_STATUS));
 
@@ -935,6 +947,8 @@ static void usb_uninit_common(struct brcm_usb_init_params *params)
 
 	if (USB_CTRL_MASK_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN))
 		USB_CTRL_SET_FAMILY(params, PLL_CTL, PLL_IDDQ_PWRDN);
+	if (params->wake_enabled)
+		usb_wake_enable(params, true);
 }
 
 static void usb_uninit_eohci(struct brcm_usb_init_params *params)
@@ -978,17 +992,6 @@ static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 	}
 }
 
-static void usb_wake_enable(struct brcm_usb_init_params *params,
-			  int enable)
-{
-	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
-
-	if (enable)
-		USB_CTRL_SET(ctrl, USB_PM, RMTWKUP_EN);
-	else
-		USB_CTRL_UNSET(ctrl, USB_PM, RMTWKUP_EN);
-}
-
 static const struct brcm_usb_init_ops bcm7445_ops = {
 	.init_ipp = usb_init_ipp,
 	.init_common = usb_init_common,
@@ -999,7 +1002,6 @@ static const struct brcm_usb_init_ops bcm7445_ops = {
 	.uninit_xhci = usb_uninit_xhci,
 	.get_dual_select = usb_get_dual_select,
 	.set_dual_select = usb_set_dual_select,
-	.wake_enable = usb_wake_enable,
 };
 
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params)
diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.h b/drivers/phy/broadcom/phy-brcm-usb-init.h
index 4cdd9cc1c5a3..899b9eb43fad 100644
--- a/drivers/phy/broadcom/phy-brcm-usb-init.h
+++ b/drivers/phy/broadcom/phy-brcm-usb-init.h
@@ -46,8 +46,6 @@ struct brcm_usb_init_ops {
 	void (*uninit_xhci)(struct brcm_usb_init_params *params);
 	int  (*get_dual_select)(struct brcm_usb_init_params *params);
 	void (*set_dual_select)(struct brcm_usb_init_params *params, int mode);
-	void (*wake_enable)(struct brcm_usb_init_params *params,
-			    int enable);
 };
 
 struct  brcm_usb_init_params {
@@ -62,6 +60,8 @@ struct  brcm_usb_init_params {
 	const u32 *usb_reg_bits_map;
 	const struct brcm_usb_init_ops *ops;
 	struct regmap *syscon_piarbctl;
+	bool wake_enabled;
+	bool suspend_with_clocks;
 };
 
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
@@ -145,13 +145,6 @@ static inline void brcm_usb_uninit_xhci(struct brcm_usb_init_params *ini)
 		ini->ops->uninit_xhci(ini);
 }
 
-static inline void brcm_usb_wake_enable(struct brcm_usb_init_params *ini,
-	int enable)
-{
-	if (ini->ops->wake_enable)
-		ini->ops->wake_enable(ini, enable);
-}
-
 static inline int brcm_usb_get_dual_select(struct brcm_usb_init_params *ini)
 {
 	if (ini->ops->get_dual_select)
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 1ab44f54244b..491bbd46c5b3 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -535,16 +535,26 @@ static int brcm_usb_phy_suspend(struct device *dev)
 	struct brcm_usb_phy_data *priv = dev_get_drvdata(dev);
 
 	if (priv->init_count) {
+		priv->ini.wake_enabled = device_may_wakeup(dev);
 		if (priv->phys[BRCM_USB_PHY_3_0].inited)
 			brcm_usb_uninit_xhci(&priv->ini);
 		if (priv->phys[BRCM_USB_PHY_2_0].inited)
 			brcm_usb_uninit_eohci(&priv->ini);
 		brcm_usb_uninit_common(&priv->ini);
-		brcm_usb_wake_enable(&priv->ini, true);
-		if (priv->phys[BRCM_USB_PHY_3_0].inited)
-			clk_disable_unprepare(priv->usb_30_clk);
-		if (priv->phys[BRCM_USB_PHY_2_0].inited || !priv->has_eohci)
-			clk_disable_unprepare(priv->usb_20_clk);
+
+		/*
+		 * Handle the clocks unless needed for wake. This has
+		 * to work for both older XHCI->3.0-clks, EOHCI->2.0-clks
+		 * and newer XHCI->2.0-clks/3.0-clks.
+		 */
+
+		if (!priv->ini.suspend_with_clocks) {
+			if (priv->phys[BRCM_USB_PHY_3_0].inited)
+				clk_disable_unprepare(priv->usb_30_clk);
+			if (priv->phys[BRCM_USB_PHY_2_0].inited ||
+			    !priv->has_eohci)
+				clk_disable_unprepare(priv->usb_20_clk);
+		}
 		if (priv->wake_irq >= 0)
 			enable_irq_wake(priv->wake_irq);
 	}
@@ -557,7 +567,6 @@ static int brcm_usb_phy_resume(struct device *dev)
 
 	clk_prepare_enable(priv->usb_20_clk);
 	clk_prepare_enable(priv->usb_30_clk);
-	brcm_usb_wake_enable(&priv->ini, false);
 	brcm_usb_init_ipp(&priv->ini);
 
 	/*
@@ -579,6 +588,8 @@ static int brcm_usb_phy_resume(struct device *dev)
 		} else if (priv->has_xhci) {
 			brcm_usb_uninit_xhci(&priv->ini);
 			clk_disable_unprepare(priv->usb_30_clk);
+			if (!priv->has_eohci)
+				clk_disable_unprepare(priv->usb_20_clk);
 		}
 	} else {
 		if (priv->has_xhci)
@@ -589,7 +600,7 @@ static int brcm_usb_phy_resume(struct device *dev)
 		clk_disable_unprepare(priv->usb_20_clk);
 		clk_disable_unprepare(priv->usb_30_clk);
 	}
-
+	priv->ini.wake_enabled = false;
 	return 0;
 }
 #endif /* CONFIG_PM_SLEEP */
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 00/13] phy: usb: Updates to Broadcom STB USB PHY driver

[Florian Fainelli]

On 12/10/19 5:21 AM, Al Cooper wrote:
> This patchset contains various updates to the Broadcom STB USB Driver.
> The updates include:
> - Add support for 7216 and 7211 Broadcom SoCs which use the new
>   Synopsis USB Controller.
> - Add support for USB Wake
> - Add various bug fixes.
> 
> v3 - Rebase to v5.5-rc1
> 
> v2 - Changes based on review feedback
> - Add vendor prefix to DT property "syscon-piarbctl"
> - Use standard "wakeup" instead of "wake" for DT "interrupt-names"

This entire series:

Tested-by: Florian Fainelli <f.fainelli@gmail.com>

> 
> Al Cooper (13):
>   phy: usb: EHCI DMA may lose a burst of DMA data for 7255xA0 family
>   phy: usb: Get all drivers that use USB clks using correct
>     enable/disable
>   phy: usb: Put USB phys into IDDQ on suspend to save power in S2 mode
>   phy: usb: Add "wake on" functionality
>   phy: usb: Restructure in preparation for adding 7216 USB support
>   dt-bindings: Add Broadcom STB USB PHY binding document
>   phy: usb: Add support for new Synopsis USB controller on the 7216
>   phy: usb: Add support for new Synopsis USB controller on the 7211b0
>   phy: usb: fix driver to defer on clk_get defer
>   phy: usb: PHY's MDIO registers not accessible without device installed
>   phy: usb: bdc: Fix occasional failure with BDC on 7211
>   phy: usb: USB driver is crashing during S3 resume on 7216
>   phy: usb: Add support for wake and USB low power mode for 7211 S2/S5
> 
>  .../bindings/phy/brcm,brcmstb-usb-phy.txt     |  69 ++-
>  drivers/phy/broadcom/Makefile                 |   2 +-
>  .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 414 ++++++++++++++++++
>  drivers/phy/broadcom/phy-brcm-usb-init.c      | 226 +++++-----
>  drivers/phy/broadcom/phy-brcm-usb-init.h      | 148 ++++++-
>  drivers/phy/broadcom/phy-brcm-usb.c           | 269 ++++++++++--
>  6 files changed, 943 insertions(+), 185 deletions(-)
>  create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> 


-- 
Florian

Re: [PATCH v3 00/13] phy: usb: Updates to Broadcom STB USB PHY driver

[Florian Fainelli]

On 12/10/19 5:21 AM, Al Cooper wrote:
> This patchset contains various updates to the Broadcom STB USB Driver.
> The updates include:
> - Add support for 7216 and 7211 Broadcom SoCs which use the new
>   Synopsis USB Controller.
> - Add support for USB Wake
> - Add various bug fixes.
> 
> v3 - Rebase to v5.5-rc1
> 
> v2 - Changes based on review feedback
> - Add vendor prefix to DT property "syscon-piarbctl"
> - Use standard "wakeup" instead of "wake" for DT "interrupt-names"

This entire series:

Tested-by: Florian Fainelli <f.fainelli@gmail.com>

> 
> Al Cooper (13):
>   phy: usb: EHCI DMA may lose a burst of DMA data for 7255xA0 family
>   phy: usb: Get all drivers that use USB clks using correct
>     enable/disable
>   phy: usb: Put USB phys into IDDQ on suspend to save power in S2 mode
>   phy: usb: Add "wake on" functionality
>   phy: usb: Restructure in preparation for adding 7216 USB support
>   dt-bindings: Add Broadcom STB USB PHY binding document
>   phy: usb: Add support for new Synopsis USB controller on the 7216
>   phy: usb: Add support for new Synopsis USB controller on the 7211b0
>   phy: usb: fix driver to defer on clk_get defer
>   phy: usb: PHY's MDIO registers not accessible without device installed
>   phy: usb: bdc: Fix occasional failure with BDC on 7211
>   phy: usb: USB driver is crashing during S3 resume on 7216
>   phy: usb: Add support for wake and USB low power mode for 7211 S2/S5
> 
>  .../bindings/phy/brcm,brcmstb-usb-phy.txt     |  69 ++-
>  drivers/phy/broadcom/Makefile                 |   2 +-
>  .../phy/broadcom/phy-brcm-usb-init-synopsis.c | 414 ++++++++++++++++++
>  drivers/phy/broadcom/phy-brcm-usb-init.c      | 226 +++++-----
>  drivers/phy/broadcom/phy-brcm-usb-init.h      | 148 ++++++-
>  drivers/phy/broadcom/phy-brcm-usb.c           | 269 ++++++++++--
>  6 files changed, 943 insertions(+), 185 deletions(-)
>  create mode 100644 drivers/phy/broadcom/phy-brcm-usb-init-synopsis.c
> 


-- 
Florian

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 00/13] phy: usb: Updates to Broadcom STB USB PHY driver

[Florian Fainelli]

On 12/13/19 11:25 AM, Florian Fainelli wrote:
> On 12/10/19 5:21 AM, Al Cooper wrote:
>> This patchset contains various updates to the Broadcom STB USB Driver.
>> The updates include:
>> - Add support for 7216 and 7211 Broadcom SoCs which use the new
>>   Synopsis USB Controller.
>> - Add support for USB Wake
>> - Add various bug fixes.
>>
>> v3 - Rebase to v5.5-rc1
>>
>> v2 - Changes based on review feedback
>> - Add vendor prefix to DT property "syscon-piarbctl"
>> - Use standard "wakeup" instead of "wake" for DT "interrupt-names"
> 
> This entire series:
> 
> Tested-by: Florian Fainelli <f.fainelli@gmail.com>

Kishon, are you good with this patch series version? Thanks! The Device
Tree binding was Reviewed by Rob earlier, though this was unfortunately
dropped in this submission (v3), here is his Reviewed-by tag response:

https://lore.kernel.org/linux-arm-kernel/20191203193421.GA9078@bogus/

Thanks!
-- 
Florian

Re: [PATCH v3 00/13] phy: usb: Updates to Broadcom STB USB PHY driver

[Florian Fainelli]

On 12/13/19 11:25 AM, Florian Fainelli wrote:
> On 12/10/19 5:21 AM, Al Cooper wrote:
>> This patchset contains various updates to the Broadcom STB USB Driver.
>> The updates include:
>> - Add support for 7216 and 7211 Broadcom SoCs which use the new
>>   Synopsis USB Controller.
>> - Add support for USB Wake
>> - Add various bug fixes.
>>
>> v3 - Rebase to v5.5-rc1
>>
>> v2 - Changes based on review feedback
>> - Add vendor prefix to DT property "syscon-piarbctl"
>> - Use standard "wakeup" instead of "wake" for DT "interrupt-names"
> 
> This entire series:
> 
> Tested-by: Florian Fainelli <f.fainelli@gmail.com>

Kishon, are you good with this patch series version? Thanks! The Device
Tree binding was Reviewed by Rob earlier, though this was unfortunately
dropped in this submission (v3), here is his Reviewed-by tag response:

https://lore.kernel.org/linux-arm-kernel/20191203193421.GA9078@bogus/

Thanks!
-- 
Florian

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel