From: Benoit Parrot <bparrot@ti.com> To: Tony Lindgren <tony@atomide.com>, Tero Kristo <t-kristo@ti.com>, <linux-omap@vger.kernel.org>, <linux-clk@vger.kernel.org> Cc: Rob Herring <robh+dt@kernel.org>, <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>, Benoit Parrot <bparrot@ti.com> Subject: [Patch v4 07/10] arm: dtsi: dra76x: Add CAL dtsi node Date: Wed, 11 Dec 2019 08:05:55 -0600 [thread overview] Message-ID: <20191211140558.10407-8-bparrot@ti.com> (raw) In-Reply-To: <20191211140558.10407-1-bparrot@ti.com> Add the required dtsi node to support the Camera Adaptation Layer (CAL) for the DRA76 family of devices. Signed-off-by: Benoit Parrot <bparrot@ti.com> --- arch/arm/boot/dts/dra76x.dtsi | 42 +++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+) diff --git a/arch/arm/boot/dts/dra76x.dtsi b/arch/arm/boot/dts/dra76x.dtsi index cdcba3f561c4..2f7539afef2b 100644 --- a/arch/arm/boot/dts/dra76x.dtsi +++ b/arch/arm/boot/dts/dra76x.dtsi @@ -41,6 +41,48 @@ }; +&l4_per3 { + target-module@1b0000 { /* 0x489b0000, ap 25 34.0 */ + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x1b0000 0x4>, + <0x1b0010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>; + clocks = <&cam_clkctrl DRA7_CAM_VIP3_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1b0000 0x10000>; + + cal: cal@0 { + compatible = "ti,dra76-cal"; + reg = <0x0000 0x400>, + <0x0800 0x40>, + <0x0900 0x40>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1"; + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + ti,camerrx-control = <&scm_conf 0x6dc>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + }; + csi2_1: port@1 { + reg = <1>; + }; + }; + }; + }; +}; + /* MCAN interrupts are hard-wired to irqs 67, 68 */ &crossbar_mpu { ti,irqs-skip = <10 67 68 133 139 140>; -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: Benoit Parrot <bparrot@ti.com> To: Tony Lindgren <tony@atomide.com>, Tero Kristo <t-kristo@ti.com>, linux-omap@vger.kernel.org, linux-clk@vger.kernel.org Cc: Rob Herring <robh+dt@kernel.org>, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Benoit Parrot <bparrot@ti.com> Subject: [Patch v4 07/10] arm: dtsi: dra76x: Add CAL dtsi node Date: Wed, 11 Dec 2019 08:05:55 -0600 [thread overview] Message-ID: <20191211140558.10407-8-bparrot@ti.com> (raw) In-Reply-To: <20191211140558.10407-1-bparrot@ti.com> Add the required dtsi node to support the Camera Adaptation Layer (CAL) for the DRA76 family of devices. Signed-off-by: Benoit Parrot <bparrot@ti.com> --- arch/arm/boot/dts/dra76x.dtsi | 42 +++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+) diff --git a/arch/arm/boot/dts/dra76x.dtsi b/arch/arm/boot/dts/dra76x.dtsi index cdcba3f561c4..2f7539afef2b 100644 --- a/arch/arm/boot/dts/dra76x.dtsi +++ b/arch/arm/boot/dts/dra76x.dtsi @@ -41,6 +41,48 @@ }; +&l4_per3 { + target-module@1b0000 { /* 0x489b0000, ap 25 34.0 */ + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x1b0000 0x4>, + <0x1b0010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>; + clocks = <&cam_clkctrl DRA7_CAM_VIP3_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1b0000 0x10000>; + + cal: cal@0 { + compatible = "ti,dra76-cal"; + reg = <0x0000 0x400>, + <0x0800 0x40>, + <0x0900 0x40>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1"; + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + ti,camerrx-control = <&scm_conf 0x6dc>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + }; + csi2_1: port@1 { + reg = <1>; + }; + }; + }; + }; +}; + /* MCAN interrupts are hard-wired to irqs 67, 68 */ &crossbar_mpu { ti,irqs-skip = <10 67 68 133 139 140>; -- 2.17.1
next prev parent reply other threads:[~2019-12-11 14:02 UTC|newest] Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-12-11 14:05 [Patch v4 00/10] ARM: dts: dra7: add cal nodes Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot 2019-12-11 14:05 ` [Patch v4 01/10] clk: ti: dra7: add cam clkctrl data Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot 2019-12-30 19:58 ` Stephen Boyd 2019-12-30 19:58 ` Stephen Boyd 2020-01-21 7:32 ` Tero Kristo 2020-01-21 7:32 ` Tero Kristo 2019-12-11 14:05 ` [Patch v4 02/10] ARM: dts: dra7: add cam clkctrl node Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot 2019-12-11 14:05 ` [Patch v4 03/10] ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot 2019-12-11 14:05 ` [Patch v4 04/10] ARM: dts: dra7-l4: Add ti-sysc node for CAM Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot 2019-12-11 14:05 ` [Patch v4 05/10] ARM: dts: DRA72: Add CAL dtsi node Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot 2019-12-11 14:05 ` [Patch v4 06/10] arm: dts: dra72-evm-common: Add entries for the CSI2 cameras Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot [this message] 2019-12-11 14:05 ` [Patch v4 07/10] arm: dtsi: dra76x: Add CAL dtsi node Benoit Parrot 2019-12-11 14:05 ` [Patch v4 08/10] arm: dts: dra76-evm: Add CAL and OV5640 nodes Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot 2019-12-11 14:05 ` [Patch v4 09/10] arm64: dts: k3-am65-main Add CAL node Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot 2020-01-24 11:32 ` Tero Kristo 2020-01-24 11:32 ` Tero Kristo 2019-12-11 14:05 ` [Patch v4 10/10] arm64: dts: k3-am654-base-board: Add CSI2 OV5640 camera Benoit Parrot 2019-12-11 14:05 ` Benoit Parrot 2020-01-23 17:17 ` [Patch v4 00/10] ARM: dts: dra7: add cal nodes Tony Lindgren 2020-01-23 17:17 ` Tony Lindgren 2020-01-23 17:26 ` Tony Lindgren 2020-01-24 7:21 ` Tero Kristo 2020-01-24 7:21 ` Tero Kristo 2020-01-24 7:25 ` Tero Kristo 2020-01-24 7:25 ` Tero Kristo
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20191211140558.10407-8-bparrot@ti.com \ --to=bparrot@ti.com \ --cc=devicetree@vger.kernel.org \ --cc=linux-clk@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-omap@vger.kernel.org \ --cc=robh+dt@kernel.org \ --cc=t-kristo@ti.com \ --cc=tony@atomide.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.