* [PATCH V5 0/5] Add minimal boot support for IPQ6018
@ 2020-01-16 7:44 ` Sricharan R
0 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
The IPQ6018 is Qualcomm\u2019s 802.11ax SoC for Routers,
Gateways and Access Points.
This series adds minimal board boot support for ipq6018-cp01 board.
[V5]
* Addressed review comments in pinctrl bindings from Rob.
* Ran make dt_binding_check with modified patch.
* Added fixed rate clocks in gcc clock controller node.
* Patch 4 arm64: dts: Add ipq6018 SoC and CP01 board support has build
dependency with,
https://lkml.org/lkml/2020/1/9/84
[v4]
* Addressed review comments in pinctrl bindings from Rob.
* Ran make dt_binding_check and no issues was reported.
* Deleted absahu email id from patch 4, since its bouncing now.
* Patch 4 arm64: dts: Add ipq6018 SoC and CP01 board support has build
dependency with,
https://lkml.org/lkml/2020/1/9/84
[V3]
* Removed clock driver and bindings from this patch series, and added them
as a different series.
* Removed qpic_padN from pinctrl driver.
* Addressed review comments in dts, and added the remaining fixed clocks their
* Fixed review comments in pinctrl bindings
[v2]
* Splitted dt bindings and driver into different patches. Added missing bindings
and some style changes.
* Added ipq6018 schema
* Addressed review comments for gcc clock bindings.
* Removed all clk critical flags, removed 1/1 factor clocks, moved to new
way of specifying clk parents, and addressed other review comments.
* Sorted nodes based on address, name, label. Removed unused clock nodes,
Addressed other review comments.
Sricharan R (5):
dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
pinctrl: qcom: Add ipq6018 pinctrl driver
dt-bindings: qcom: Add ipq6018 bindings
arm64: dts: Add ipq6018 SoC and CP01 board support
arm64: defconfig: Enable qcom ipq6018 clock and pinctrl
Documentation/devicetree/bindings/arm/qcom.yaml | 8 +
.../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 174 +++
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 30 +
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 263 +++++
arch/arm64/configs/defconfig | 3 +
drivers/pinctrl/qcom/Kconfig | 10 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-ipq6018.c | 1107 ++++++++++++++++++++
9 files changed, 1597 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi
create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq6018.c
--
1.9.1
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH V5 0/5] Add minimal boot support for IPQ6018
@ 2020-01-16 7:44 ` Sricharan R
0 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
The IPQ6018 is Qualcomm\u2019s 802.11ax SoC for Routers,
Gateways and Access Points.
This series adds minimal board boot support for ipq6018-cp01 board.
[V5]
* Addressed review comments in pinctrl bindings from Rob.
* Ran make dt_binding_check with modified patch.
* Added fixed rate clocks in gcc clock controller node.
* Patch 4 arm64: dts: Add ipq6018 SoC and CP01 board support has build
dependency with,
https://lkml.org/lkml/2020/1/9/84
[v4]
* Addressed review comments in pinctrl bindings from Rob.
* Ran make dt_binding_check and no issues was reported.
* Deleted absahu email id from patch 4, since its bouncing now.
* Patch 4 arm64: dts: Add ipq6018 SoC and CP01 board support has build
dependency with,
https://lkml.org/lkml/2020/1/9/84
[V3]
* Removed clock driver and bindings from this patch series, and added them
as a different series.
* Removed qpic_padN from pinctrl driver.
* Addressed review comments in dts, and added the remaining fixed clocks their
* Fixed review comments in pinctrl bindings
[v2]
* Splitted dt bindings and driver into different patches. Added missing bindings
and some style changes.
* Added ipq6018 schema
* Addressed review comments for gcc clock bindings.
* Removed all clk critical flags, removed 1/1 factor clocks, moved to new
way of specifying clk parents, and addressed other review comments.
* Sorted nodes based on address, name, label. Removed unused clock nodes,
Addressed other review comments.
Sricharan R (5):
dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
pinctrl: qcom: Add ipq6018 pinctrl driver
dt-bindings: qcom: Add ipq6018 bindings
arm64: dts: Add ipq6018 SoC and CP01 board support
arm64: defconfig: Enable qcom ipq6018 clock and pinctrl
Documentation/devicetree/bindings/arm/qcom.yaml | 8 +
.../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 174 +++
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 30 +
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 263 +++++
arch/arm64/configs/defconfig | 3 +
drivers/pinctrl/qcom/Kconfig | 10 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-ipq6018.c | 1107 ++++++++++++++++++++
9 files changed, 1597 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi
create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq6018.c
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
2020-01-16 7:44 ` Sricharan R
@ 2020-01-16 7:44 ` Sricharan R
-1 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
Cc: Rajkumar Ayyasamy, Selvam Sathappan Periakaruppan
Add device tree binding Documentation details for ipq6018
pinctrl driver.
Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
[V5]
* Addressed review comments from Rob
* Ran dt bindings check and no errors were reported
.../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 162 +++++++++++++++++++++
1 file changed, 162 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
new file mode 100644
index 0000000..0622258
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
@@ -0,0 +1,162 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
+
+maintainers:
+ - Sricharan R <sricharan@codeaurora.org>
+
+description: |
+ This binding describes the Top Level Mode Multiplexer block found in the
+ IPQ6018 platform.
+
+properties:
+ compatible:
+ const: qcom,ipq6018-pinctrl
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ description: Specifies the TLMM summary IRQ
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ description:
+ Specifies the PIN numbers and Flags, as defined in defined in
+ include/dt-bindings/interrupt-controller/irq.h
+ const: 2
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ description: Specifying the pin number and flags, as defined in
+ include/dt-bindings/gpio/gpio.h
+ const: 2
+
+ gpio-ranges:
+ description: Documentation/devicetree/bindings/gpio/gpio.txt
+ maxItems: 1
+
+#PIN CONFIGURATION NODES
+patternProperties:
+ '.*-pin.*':
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ allOf:
+ - $ref: "/schemas/pinctrl/pincfg-node.yaml"
+
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in this
+ subnode. The valid values are gpio1-80, sdc1_clk, sdc1_cmd,
+ sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_cmd, qdsd_data0,
+ qdsd_data1, qdsd_data2, qdsd_data3
+ minItems: 1
+ maxItems: 4
+
+ function:
+ description:
+ Specify the alternative function to be configured for the specified
+ pins.
+ enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
+ atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
+ atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
+ atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c,
+ blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi,
+ blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi,
+ blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi,
+ blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi,
+ blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst,
+ cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
+ cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
+ dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
+ flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
+ gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
+ gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
+ ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
+ nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
+ pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
+ pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
+ pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
+ qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
+ qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
+ qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
+ qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
+ sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
+ uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
+
+ drive-strength:
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+ default: 2
+ description:
+ Selects the drive strength for the specified pins, in mA.
+
+ bias-pull-down:
+ type: boolean
+ description: The specified pin should be configured as pull down.
+
+ bias-pull-up:
+ type: boolean
+ description: The specified pin should be configured as pull up.
+
+ bias-disable:
+ type: boolean
+ description: The specified pin should be configured as no pull.
+
+ output-high:
+ type: boolean
+ description: The specified pin is configured in output mode, driven
+ high.
+
+ output-low:
+ type: boolean
+ description: The specified pin is configured in output mode, driven
+ low.
+
+ required:
+ - pins
+ - function
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,ipq6018-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 80>;
+
+ serial3-pinmux {
+ pins = "gpio44", "gpio45";
+ function = "blsp2_uart";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
@ 2020-01-16 7:44 ` Sricharan R
0 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
Cc: Selvam Sathappan Periakaruppan, Rajkumar Ayyasamy
Add device tree binding Documentation details for ipq6018
pinctrl driver.
Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
[V5]
* Addressed review comments from Rob
* Ran dt bindings check and no errors were reported
.../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 162 +++++++++++++++++++++
1 file changed, 162 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
new file mode 100644
index 0000000..0622258
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
@@ -0,0 +1,162 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
+
+maintainers:
+ - Sricharan R <sricharan@codeaurora.org>
+
+description: |
+ This binding describes the Top Level Mode Multiplexer block found in the
+ IPQ6018 platform.
+
+properties:
+ compatible:
+ const: qcom,ipq6018-pinctrl
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ description: Specifies the TLMM summary IRQ
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ description:
+ Specifies the PIN numbers and Flags, as defined in defined in
+ include/dt-bindings/interrupt-controller/irq.h
+ const: 2
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ description: Specifying the pin number and flags, as defined in
+ include/dt-bindings/gpio/gpio.h
+ const: 2
+
+ gpio-ranges:
+ description: Documentation/devicetree/bindings/gpio/gpio.txt
+ maxItems: 1
+
+#PIN CONFIGURATION NODES
+patternProperties:
+ '.*-pin.*':
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ allOf:
+ - $ref: "/schemas/pinctrl/pincfg-node.yaml"
+
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in this
+ subnode. The valid values are gpio1-80, sdc1_clk, sdc1_cmd,
+ sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_cmd, qdsd_data0,
+ qdsd_data1, qdsd_data2, qdsd_data3
+ minItems: 1
+ maxItems: 4
+
+ function:
+ description:
+ Specify the alternative function to be configured for the specified
+ pins.
+ enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
+ atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
+ atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
+ atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c,
+ blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi,
+ blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi,
+ blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi,
+ blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi,
+ blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst,
+ cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
+ cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
+ dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
+ flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
+ gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
+ gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
+ ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
+ nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
+ pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
+ pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
+ pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
+ qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
+ qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
+ qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
+ qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
+ sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
+ uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
+
+ drive-strength:
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+ default: 2
+ description:
+ Selects the drive strength for the specified pins, in mA.
+
+ bias-pull-down:
+ type: boolean
+ description: The specified pin should be configured as pull down.
+
+ bias-pull-up:
+ type: boolean
+ description: The specified pin should be configured as pull up.
+
+ bias-disable:
+ type: boolean
+ description: The specified pin should be configured as no pull.
+
+ output-high:
+ type: boolean
+ description: The specified pin is configured in output mode, driven
+ high.
+
+ output-low:
+ type: boolean
+ description: The specified pin is configured in output mode, driven
+ low.
+
+ required:
+ - pins
+ - function
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,ipq6018-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 80>;
+
+ serial3-pinmux {
+ pins = "gpio44", "gpio45";
+ function = "blsp2_uart";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH V5 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver
2020-01-16 7:44 ` Sricharan R
@ 2020-01-16 7:44 ` Sricharan R
-1 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
Cc: Rajkumar Ayyasamy, Selvam Sathappan Periakaruppan
Add initial pinctrl driver to support pin configuration with
pinctrl framework for ipq6018.
Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
drivers/pinctrl/qcom/Kconfig | 10 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-ipq6018.c | 1107 ++++++++++++++++++++++++++++++++
3 files changed, 1118 insertions(+)
create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq6018.c
diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
index 811af2f8..c5d4428 100644
--- a/drivers/pinctrl/qcom/Kconfig
+++ b/drivers/pinctrl/qcom/Kconfig
@@ -50,6 +50,16 @@ config PINCTRL_IPQ8074
Qualcomm Technologies Inc. IPQ8074 platform. Select this for
IPQ8074.
+config PINCTRL_IPQ6018
+ tristate "Qualcomm Technologies, Inc. IPQ6018 pin controller driver"
+ depends on GPIOLIB && OF
+ select PINCTRL_MSM
+ help
+ This is the pinctrl, pinmux, pinconf and gpiolib driver for
+ the Qualcomm Technologies Inc. TLMM block found on the
+ Qualcomm Technologies Inc. IPQ6018 platform. Select this for
+ IPQ6018.
+
config PINCTRL_MSM8660
tristate "Qualcomm 8660 pin controller driver"
depends on GPIOLIB && OF
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index c2c2f9a..d9e0904 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -6,6 +6,7 @@ obj-$(CONFIG_PINCTRL_APQ8084) += pinctrl-apq8084.o
obj-$(CONFIG_PINCTRL_IPQ4019) += pinctrl-ipq4019.o
obj-$(CONFIG_PINCTRL_IPQ8064) += pinctrl-ipq8064.o
obj-$(CONFIG_PINCTRL_IPQ8074) += pinctrl-ipq8074.o
+obj-$(CONFIG_PINCTRL_IPQ6018) += pinctrl-ipq6018.o
obj-$(CONFIG_PINCTRL_MSM8660) += pinctrl-msm8660.o
obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o
obj-$(CONFIG_PINCTRL_MSM8X74) += pinctrl-msm8x74.o
diff --git a/drivers/pinctrl/qcom/pinctrl-ipq6018.c b/drivers/pinctrl/qcom/pinctrl-ipq6018.c
new file mode 100644
index 0000000..38c33a7
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-ipq6018.c
@@ -0,0 +1,1107 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-msm.h"
+
+#define FUNCTION(fname) \
+ [msm_mux_##fname] = { \
+ .name = #fname, \
+ .groups = fname##_groups, \
+ .ngroups = ARRAY_SIZE(fname##_groups), \
+ }
+
+#define REG_SIZE 0x1000
+#define PINGROUP(id, f1, f2, f3, f4, f5, f6, f7, f8, f9) \
+ { \
+ .name = "gpio" #id, \
+ .pins = gpio##id##_pins, \
+ .npins = (unsigned int)ARRAY_SIZE(gpio##id##_pins), \
+ .funcs = (int[]){ \
+ msm_mux_gpio, /* gpio mode */ \
+ msm_mux_##f1, \
+ msm_mux_##f2, \
+ msm_mux_##f3, \
+ msm_mux_##f4, \
+ msm_mux_##f5, \
+ msm_mux_##f6, \
+ msm_mux_##f7, \
+ msm_mux_##f8, \
+ msm_mux_##f9 \
+ }, \
+ .nfuncs = 10, \
+ .ctl_reg = REG_SIZE * id, \
+ .io_reg = 0x4 + REG_SIZE * id, \
+ .intr_cfg_reg = 0x8 + REG_SIZE * id, \
+ .intr_status_reg = 0xc + REG_SIZE * id, \
+ .intr_target_reg = 0x8 + REG_SIZE * id, \
+ .mux_bit = 2, \
+ .pull_bit = 0, \
+ .drv_bit = 6, \
+ .oe_bit = 9, \
+ .in_bit = 0, \
+ .out_bit = 1, \
+ .intr_enable_bit = 0, \
+ .intr_status_bit = 0, \
+ .intr_target_bit = 5, \
+ .intr_target_kpss_val = 3, \
+ .intr_raw_status_bit = 4, \
+ .intr_polarity_bit = 1, \
+ .intr_detection_bit = 2, \
+ .intr_detection_width = 2, \
+ }
+
+static const struct pinctrl_pin_desc ipq6018_pins[] = {
+ PINCTRL_PIN(0, "GPIO_0"),
+ PINCTRL_PIN(1, "GPIO_1"),
+ PINCTRL_PIN(2, "GPIO_2"),
+ PINCTRL_PIN(3, "GPIO_3"),
+ PINCTRL_PIN(4, "GPIO_4"),
+ PINCTRL_PIN(5, "GPIO_5"),
+ PINCTRL_PIN(6, "GPIO_6"),
+ PINCTRL_PIN(7, "GPIO_7"),
+ PINCTRL_PIN(8, "GPIO_8"),
+ PINCTRL_PIN(9, "GPIO_9"),
+ PINCTRL_PIN(10, "GPIO_10"),
+ PINCTRL_PIN(11, "GPIO_11"),
+ PINCTRL_PIN(12, "GPIO_12"),
+ PINCTRL_PIN(13, "GPIO_13"),
+ PINCTRL_PIN(14, "GPIO_14"),
+ PINCTRL_PIN(15, "GPIO_15"),
+ PINCTRL_PIN(16, "GPIO_16"),
+ PINCTRL_PIN(17, "GPIO_17"),
+ PINCTRL_PIN(18, "GPIO_18"),
+ PINCTRL_PIN(19, "GPIO_19"),
+ PINCTRL_PIN(20, "GPIO_20"),
+ PINCTRL_PIN(21, "GPIO_21"),
+ PINCTRL_PIN(22, "GPIO_22"),
+ PINCTRL_PIN(23, "GPIO_23"),
+ PINCTRL_PIN(24, "GPIO_24"),
+ PINCTRL_PIN(25, "GPIO_25"),
+ PINCTRL_PIN(26, "GPIO_26"),
+ PINCTRL_PIN(27, "GPIO_27"),
+ PINCTRL_PIN(28, "GPIO_28"),
+ PINCTRL_PIN(29, "GPIO_29"),
+ PINCTRL_PIN(30, "GPIO_30"),
+ PINCTRL_PIN(31, "GPIO_31"),
+ PINCTRL_PIN(32, "GPIO_32"),
+ PINCTRL_PIN(33, "GPIO_33"),
+ PINCTRL_PIN(34, "GPIO_34"),
+ PINCTRL_PIN(35, "GPIO_35"),
+ PINCTRL_PIN(36, "GPIO_36"),
+ PINCTRL_PIN(37, "GPIO_37"),
+ PINCTRL_PIN(38, "GPIO_38"),
+ PINCTRL_PIN(39, "GPIO_39"),
+ PINCTRL_PIN(40, "GPIO_40"),
+ PINCTRL_PIN(41, "GPIO_41"),
+ PINCTRL_PIN(42, "GPIO_42"),
+ PINCTRL_PIN(43, "GPIO_43"),
+ PINCTRL_PIN(44, "GPIO_44"),
+ PINCTRL_PIN(45, "GPIO_45"),
+ PINCTRL_PIN(46, "GPIO_46"),
+ PINCTRL_PIN(47, "GPIO_47"),
+ PINCTRL_PIN(48, "GPIO_48"),
+ PINCTRL_PIN(49, "GPIO_49"),
+ PINCTRL_PIN(50, "GPIO_50"),
+ PINCTRL_PIN(51, "GPIO_51"),
+ PINCTRL_PIN(52, "GPIO_52"),
+ PINCTRL_PIN(53, "GPIO_53"),
+ PINCTRL_PIN(54, "GPIO_54"),
+ PINCTRL_PIN(55, "GPIO_55"),
+ PINCTRL_PIN(56, "GPIO_56"),
+ PINCTRL_PIN(57, "GPIO_57"),
+ PINCTRL_PIN(58, "GPIO_58"),
+ PINCTRL_PIN(59, "GPIO_59"),
+ PINCTRL_PIN(60, "GPIO_60"),
+ PINCTRL_PIN(61, "GPIO_61"),
+ PINCTRL_PIN(62, "GPIO_62"),
+ PINCTRL_PIN(63, "GPIO_63"),
+ PINCTRL_PIN(64, "GPIO_64"),
+ PINCTRL_PIN(65, "GPIO_65"),
+ PINCTRL_PIN(66, "GPIO_66"),
+ PINCTRL_PIN(67, "GPIO_67"),
+ PINCTRL_PIN(68, "GPIO_68"),
+ PINCTRL_PIN(69, "GPIO_69"),
+ PINCTRL_PIN(70, "GPIO_70"),
+ PINCTRL_PIN(71, "GPIO_71"),
+ PINCTRL_PIN(72, "GPIO_72"),
+ PINCTRL_PIN(73, "GPIO_73"),
+ PINCTRL_PIN(74, "GPIO_74"),
+ PINCTRL_PIN(75, "GPIO_75"),
+ PINCTRL_PIN(76, "GPIO_76"),
+ PINCTRL_PIN(77, "GPIO_77"),
+ PINCTRL_PIN(78, "GPIO_78"),
+ PINCTRL_PIN(79, "GPIO_79"),
+};
+
+#define DECLARE_MSM_GPIO_PINS(pin) \
+ static const unsigned int gpio##pin##_pins[] = { pin }
+DECLARE_MSM_GPIO_PINS(0);
+DECLARE_MSM_GPIO_PINS(1);
+DECLARE_MSM_GPIO_PINS(2);
+DECLARE_MSM_GPIO_PINS(3);
+DECLARE_MSM_GPIO_PINS(4);
+DECLARE_MSM_GPIO_PINS(5);
+DECLARE_MSM_GPIO_PINS(6);
+DECLARE_MSM_GPIO_PINS(7);
+DECLARE_MSM_GPIO_PINS(8);
+DECLARE_MSM_GPIO_PINS(9);
+DECLARE_MSM_GPIO_PINS(10);
+DECLARE_MSM_GPIO_PINS(11);
+DECLARE_MSM_GPIO_PINS(12);
+DECLARE_MSM_GPIO_PINS(13);
+DECLARE_MSM_GPIO_PINS(14);
+DECLARE_MSM_GPIO_PINS(15);
+DECLARE_MSM_GPIO_PINS(16);
+DECLARE_MSM_GPIO_PINS(17);
+DECLARE_MSM_GPIO_PINS(18);
+DECLARE_MSM_GPIO_PINS(19);
+DECLARE_MSM_GPIO_PINS(20);
+DECLARE_MSM_GPIO_PINS(21);
+DECLARE_MSM_GPIO_PINS(22);
+DECLARE_MSM_GPIO_PINS(23);
+DECLARE_MSM_GPIO_PINS(24);
+DECLARE_MSM_GPIO_PINS(25);
+DECLARE_MSM_GPIO_PINS(26);
+DECLARE_MSM_GPIO_PINS(27);
+DECLARE_MSM_GPIO_PINS(28);
+DECLARE_MSM_GPIO_PINS(29);
+DECLARE_MSM_GPIO_PINS(30);
+DECLARE_MSM_GPIO_PINS(31);
+DECLARE_MSM_GPIO_PINS(32);
+DECLARE_MSM_GPIO_PINS(33);
+DECLARE_MSM_GPIO_PINS(34);
+DECLARE_MSM_GPIO_PINS(35);
+DECLARE_MSM_GPIO_PINS(36);
+DECLARE_MSM_GPIO_PINS(37);
+DECLARE_MSM_GPIO_PINS(38);
+DECLARE_MSM_GPIO_PINS(39);
+DECLARE_MSM_GPIO_PINS(40);
+DECLARE_MSM_GPIO_PINS(41);
+DECLARE_MSM_GPIO_PINS(42);
+DECLARE_MSM_GPIO_PINS(43);
+DECLARE_MSM_GPIO_PINS(44);
+DECLARE_MSM_GPIO_PINS(45);
+DECLARE_MSM_GPIO_PINS(46);
+DECLARE_MSM_GPIO_PINS(47);
+DECLARE_MSM_GPIO_PINS(48);
+DECLARE_MSM_GPIO_PINS(49);
+DECLARE_MSM_GPIO_PINS(50);
+DECLARE_MSM_GPIO_PINS(51);
+DECLARE_MSM_GPIO_PINS(52);
+DECLARE_MSM_GPIO_PINS(53);
+DECLARE_MSM_GPIO_PINS(54);
+DECLARE_MSM_GPIO_PINS(55);
+DECLARE_MSM_GPIO_PINS(56);
+DECLARE_MSM_GPIO_PINS(57);
+DECLARE_MSM_GPIO_PINS(58);
+DECLARE_MSM_GPIO_PINS(59);
+DECLARE_MSM_GPIO_PINS(60);
+DECLARE_MSM_GPIO_PINS(61);
+DECLARE_MSM_GPIO_PINS(62);
+DECLARE_MSM_GPIO_PINS(63);
+DECLARE_MSM_GPIO_PINS(64);
+DECLARE_MSM_GPIO_PINS(65);
+DECLARE_MSM_GPIO_PINS(66);
+DECLARE_MSM_GPIO_PINS(67);
+DECLARE_MSM_GPIO_PINS(68);
+DECLARE_MSM_GPIO_PINS(69);
+DECLARE_MSM_GPIO_PINS(70);
+DECLARE_MSM_GPIO_PINS(71);
+DECLARE_MSM_GPIO_PINS(72);
+DECLARE_MSM_GPIO_PINS(73);
+DECLARE_MSM_GPIO_PINS(74);
+DECLARE_MSM_GPIO_PINS(75);
+DECLARE_MSM_GPIO_PINS(76);
+DECLARE_MSM_GPIO_PINS(77);
+DECLARE_MSM_GPIO_PINS(78);
+DECLARE_MSM_GPIO_PINS(79);
+
+enum ipq6018_functions {
+ msm_mux_atest_char,
+ msm_mux_atest_char0,
+ msm_mux_atest_char1,
+ msm_mux_atest_char2,
+ msm_mux_atest_char3,
+ msm_mux_audio0,
+ msm_mux_audio1,
+ msm_mux_audio2,
+ msm_mux_audio3,
+ msm_mux_audio_rxbclk,
+ msm_mux_audio_rxfsync,
+ msm_mux_audio_rxmclk,
+ msm_mux_audio_rxmclkin,
+ msm_mux_audio_txbclk,
+ msm_mux_audio_txfsync,
+ msm_mux_audio_txmclk,
+ msm_mux_audio_txmclkin,
+ msm_mux_blsp0_i2c,
+ msm_mux_blsp0_spi,
+ msm_mux_blsp0_uart,
+ msm_mux_blsp1_i2c,
+ msm_mux_blsp1_spi,
+ msm_mux_blsp1_uart,
+ msm_mux_blsp2_i2c,
+ msm_mux_blsp2_spi,
+ msm_mux_blsp2_uart,
+ msm_mux_blsp3_i2c,
+ msm_mux_blsp3_spi,
+ msm_mux_blsp3_uart,
+ msm_mux_blsp4_i2c,
+ msm_mux_blsp4_spi,
+ msm_mux_blsp4_uart,
+ msm_mux_blsp5_i2c,
+ msm_mux_blsp5_uart,
+ msm_mux_burn0,
+ msm_mux_burn1,
+ msm_mux_cri_trng,
+ msm_mux_cri_trng0,
+ msm_mux_cri_trng1,
+ msm_mux_cxc0,
+ msm_mux_cxc1,
+ msm_mux_dbg_out,
+ msm_mux_gcc_plltest,
+ msm_mux_gcc_tlmm,
+ msm_mux_gpio,
+ msm_mux_lpass_aud,
+ msm_mux_lpass_aud0,
+ msm_mux_lpass_aud1,
+ msm_mux_lpass_aud2,
+ msm_mux_lpass_pcm,
+ msm_mux_lpass_pdm,
+ msm_mux_mac00,
+ msm_mux_mac01,
+ msm_mux_mac10,
+ msm_mux_mac11,
+ msm_mux_mac12,
+ msm_mux_mac13,
+ msm_mux_mac20,
+ msm_mux_mac21,
+ msm_mux_mdc,
+ msm_mux_mdio,
+ msm_mux_pcie0_clk,
+ msm_mux_pcie0_rst,
+ msm_mux_pcie0_wake,
+ msm_mux_prng_rosc,
+ msm_mux_pta1_0,
+ msm_mux_pta1_1,
+ msm_mux_pta1_2,
+ msm_mux_pta2_0,
+ msm_mux_pta2_1,
+ msm_mux_pta2_2,
+ msm_mux_pwm00,
+ msm_mux_pwm01,
+ msm_mux_pwm02,
+ msm_mux_pwm03,
+ msm_mux_pwm04,
+ msm_mux_pwm10,
+ msm_mux_pwm11,
+ msm_mux_pwm12,
+ msm_mux_pwm13,
+ msm_mux_pwm14,
+ msm_mux_pwm20,
+ msm_mux_pwm21,
+ msm_mux_pwm22,
+ msm_mux_pwm23,
+ msm_mux_pwm24,
+ msm_mux_pwm30,
+ msm_mux_pwm31,
+ msm_mux_pwm32,
+ msm_mux_pwm33,
+ msm_mux_qdss_cti_trig_in_a0,
+ msm_mux_qdss_cti_trig_in_a1,
+ msm_mux_qdss_cti_trig_out_a0,
+ msm_mux_qdss_cti_trig_out_a1,
+ msm_mux_qdss_cti_trig_in_b0,
+ msm_mux_qdss_cti_trig_in_b1,
+ msm_mux_qdss_cti_trig_out_b0,
+ msm_mux_qdss_cti_trig_out_b1,
+ msm_mux_qdss_traceclk_a,
+ msm_mux_qdss_tracectl_a,
+ msm_mux_qdss_tracedata_a,
+ msm_mux_qdss_traceclk_b,
+ msm_mux_qdss_tracectl_b,
+ msm_mux_qdss_tracedata_b,
+ msm_mux_qpic_pad,
+ msm_mux_rx0,
+ msm_mux_rx1,
+ msm_mux_rx_swrm,
+ msm_mux_rx_swrm0,
+ msm_mux_rx_swrm1,
+ msm_mux_sd_card,
+ msm_mux_sd_write,
+ msm_mux_tsens_max,
+ msm_mux_tx_swrm,
+ msm_mux_tx_swrm0,
+ msm_mux_tx_swrm1,
+ msm_mux_tx_swrm2,
+ msm_mux_wci20,
+ msm_mux_wci21,
+ msm_mux_wci22,
+ msm_mux_wci23,
+ msm_mux_wsa_swrm,
+ msm_mux__,
+};
+
+static const char * const blsp3_uart_groups[] = {
+ "gpio73", "gpio74", "gpio75", "gpio76",
+};
+
+static const char * const blsp3_i2c_groups[] = {
+ "gpio73", "gpio74",
+};
+
+static const char * const blsp3_spi_groups[] = {
+ "gpio73", "gpio74", "gpio75", "gpio76", "gpio77", "gpio78", "gpio79",
+};
+
+static const char * const wci20_groups[] = {
+ "gpio0", "gpio2",
+};
+
+static const char * const qpic_pad_groups[] = {
+ "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio9", "gpio10",
+ "gpio11", "gpio17",
+};
+
+static const char * const burn0_groups[] = {
+ "gpio0",
+};
+
+static const char * const mac12_groups[] = {
+ "gpio1", "gpio11",
+};
+
+static const char * const qdss_tracectl_b_groups[] = {
+ "gpio1",
+};
+
+static const char * const burn1_groups[] = {
+ "gpio1",
+};
+
+static const char * const qdss_traceclk_b_groups[] = {
+ "gpio0",
+};
+
+static const char * const qdss_tracedata_b_groups[] = {
+ "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8", "gpio9",
+ "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15", "gpio16",
+ "gpio17",
+};
+
+static const char * const mac01_groups[] = {
+ "gpio3", "gpio4",
+};
+
+static const char * const mac21_groups[] = {
+ "gpio5", "gpio6",
+};
+
+static const char * const atest_char_groups[] = {
+ "gpio9",
+};
+
+static const char * const cxc0_groups[] = {
+ "gpio9", "gpio16",
+};
+
+static const char * const mac13_groups[] = {
+ "gpio9", "gpio16",
+};
+
+static const char * const dbg_out_groups[] = {
+ "gpio9",
+};
+
+static const char * const wci22_groups[] = {
+ "gpio11", "gpio17",
+};
+
+static const char * const pwm00_groups[] = {
+ "gpio18",
+};
+
+static const char * const atest_char0_groups[] = {
+ "gpio18",
+};
+
+static const char * const wci23_groups[] = {
+ "gpio18", "gpio19",
+};
+
+static const char * const mac11_groups[] = {
+ "gpio18", "gpio19",
+};
+
+static const char * const pwm10_groups[] = {
+ "gpio19",
+};
+
+static const char * const atest_char1_groups[] = {
+ "gpio19",
+};
+
+static const char * const pwm20_groups[] = {
+ "gpio20",
+};
+
+static const char * const atest_char2_groups[] = {
+ "gpio20",
+};
+
+static const char * const pwm30_groups[] = {
+ "gpio21",
+};
+
+static const char * const atest_char3_groups[] = {
+ "gpio21",
+};
+
+static const char * const audio_txmclk_groups[] = {
+ "gpio22",
+};
+
+static const char * const audio_txmclkin_groups[] = {
+ "gpio22",
+};
+
+static const char * const pwm02_groups[] = {
+ "gpio22",
+};
+
+static const char * const tx_swrm0_groups[] = {
+ "gpio22",
+};
+
+static const char * const qdss_cti_trig_out_b0_groups[] = {
+ "gpio22",
+};
+
+static const char * const audio_txbclk_groups[] = {
+ "gpio23",
+};
+
+static const char * const pwm12_groups[] = {
+ "gpio23",
+};
+
+static const char * const wsa_swrm_groups[] = {
+ "gpio23", "gpio24",
+};
+
+static const char * const tx_swrm1_groups[] = {
+ "gpio23",
+};
+
+static const char * const qdss_cti_trig_in_b0_groups[] = {
+ "gpio23",
+};
+
+static const char * const audio_txfsync_groups[] = {
+ "gpio24",
+};
+
+static const char * const pwm22_groups[] = {
+ "gpio24",
+};
+
+static const char * const tx_swrm2_groups[] = {
+ "gpio24",
+};
+
+static const char * const qdss_cti_trig_out_b1_groups[] = {
+ "gpio24",
+};
+
+static const char * const audio0_groups[] = {
+ "gpio25", "gpio32",
+};
+
+static const char * const pwm32_groups[] = {
+ "gpio25",
+};
+
+static const char * const tx_swrm_groups[] = {
+ "gpio25",
+};
+
+static const char * const qdss_cti_trig_in_b1_groups[] = {
+ "gpio25",
+};
+
+static const char * const audio1_groups[] = {
+ "gpio26", "gpio33",
+};
+
+static const char * const pwm04_groups[] = {
+ "gpio26",
+};
+
+static const char * const audio2_groups[] = {
+ "gpio27",
+};
+
+static const char * const pwm14_groups[] = {
+ "gpio27",
+};
+
+static const char * const audio3_groups[] = {
+ "gpio28",
+};
+
+static const char * const pwm24_groups[] = {
+ "gpio28",
+};
+
+static const char * const audio_rxmclk_groups[] = {
+ "gpio29",
+};
+
+static const char * const audio_rxmclkin_groups[] = {
+ "gpio29",
+};
+
+static const char * const pwm03_groups[] = {
+ "gpio29",
+};
+
+static const char * const lpass_pdm_groups[] = {
+ "gpio29", "gpio30", "gpio31", "gpio32",
+};
+
+static const char * const lpass_aud_groups[] = {
+ "gpio29",
+};
+
+static const char * const qdss_cti_trig_in_a1_groups[] = {
+ "gpio29",
+};
+
+static const char * const audio_rxbclk_groups[] = {
+ "gpio30",
+};
+
+static const char * const pwm13_groups[] = {
+ "gpio30",
+};
+
+static const char * const lpass_aud0_groups[] = {
+ "gpio30",
+};
+
+static const char * const rx_swrm_groups[] = {
+ "gpio30",
+};
+
+static const char * const qdss_cti_trig_out_a1_groups[] = {
+ "gpio30",
+};
+
+static const char * const audio_rxfsync_groups[] = {
+ "gpio31",
+};
+
+static const char * const pwm23_groups[] = {
+ "gpio31",
+};
+
+static const char * const lpass_aud1_groups[] = {
+ "gpio31",
+};
+
+static const char * const rx_swrm0_groups[] = {
+ "gpio31",
+};
+
+static const char * const qdss_cti_trig_in_a0_groups[] = {
+ "gpio31",
+};
+
+static const char * const pwm33_groups[] = {
+ "gpio32",
+};
+
+static const char * const lpass_aud2_groups[] = {
+ "gpio32",
+};
+
+static const char * const rx_swrm1_groups[] = {
+ "gpio32",
+};
+
+static const char * const qdss_cti_trig_out_a0_groups[] = {
+ "gpio32",
+};
+
+static const char * const lpass_pcm_groups[] = {
+ "gpio34", "gpio35", "gpio36", "gpio37",
+};
+
+static const char * const mac10_groups[] = {
+ "gpio34", "gpio35",
+};
+
+static const char * const mac00_groups[] = {
+ "gpio34", "gpio35",
+};
+
+static const char * const mac20_groups[] = {
+ "gpio36", "gpio37",
+};
+
+static const char * const blsp0_uart_groups[] = {
+ "gpio38", "gpio39", "gpio40", "gpio41",
+};
+
+static const char * const blsp0_i2c_groups[] = {
+ "gpio38", "gpio39",
+};
+
+static const char * const blsp0_spi_groups[] = {
+ "gpio38", "gpio39", "gpio40", "gpio41",
+};
+
+static const char * const blsp2_uart_groups[] = {
+ "gpio42", "gpio43", "gpio44", "gpio45",
+};
+
+static const char * const blsp2_i2c_groups[] = {
+ "gpio42", "gpio43",
+};
+
+static const char * const blsp2_spi_groups[] = {
+ "gpio42", "gpio43", "gpio44", "gpio45",
+};
+
+static const char * const blsp5_i2c_groups[] = {
+ "gpio46", "gpio47",
+};
+
+static const char * const blsp5_uart_groups[] = {
+ "gpio48", "gpio49",
+};
+
+static const char * const qdss_traceclk_a_groups[] = {
+ "gpio48",
+};
+
+static const char * const qdss_tracectl_a_groups[] = {
+ "gpio49",
+};
+
+static const char * const pwm01_groups[] = {
+ "gpio50",
+};
+
+static const char * const pta1_1_groups[] = {
+ "gpio51",
+};
+
+static const char * const pwm11_groups[] = {
+ "gpio51",
+};
+
+static const char * const rx1_groups[] = {
+ "gpio51",
+};
+
+static const char * const pta1_2_groups[] = {
+ "gpio52",
+};
+
+static const char * const pwm21_groups[] = {
+ "gpio52",
+};
+
+static const char * const pta1_0_groups[] = {
+ "gpio53",
+};
+
+static const char * const pwm31_groups[] = {
+ "gpio53",
+};
+
+static const char * const prng_rosc_groups[] = {
+ "gpio53",
+};
+
+static const char * const blsp4_uart_groups[] = {
+ "gpio55", "gpio56", "gpio57", "gpio58",
+};
+
+static const char * const blsp4_i2c_groups[] = {
+ "gpio55", "gpio56",
+};
+
+static const char * const blsp4_spi_groups[] = {
+ "gpio55", "gpio56", "gpio57", "gpio58",
+};
+
+static const char * const pcie0_clk_groups[] = {
+ "gpio59",
+};
+
+static const char * const cri_trng0_groups[] = {
+ "gpio59",
+};
+
+static const char * const pcie0_rst_groups[] = {
+ "gpio60",
+};
+
+static const char * const cri_trng1_groups[] = {
+ "gpio60",
+};
+
+static const char * const pcie0_wake_groups[] = {
+ "gpio61",
+};
+
+static const char * const cri_trng_groups[] = {
+ "gpio61",
+};
+
+static const char * const sd_card_groups[] = {
+ "gpio62",
+};
+
+static const char * const sd_write_groups[] = {
+ "gpio63",
+};
+
+static const char * const rx0_groups[] = {
+ "gpio63",
+};
+
+static const char * const tsens_max_groups[] = {
+ "gpio63",
+};
+
+static const char * const mdc_groups[] = {
+ "gpio64",
+};
+
+static const char * const qdss_tracedata_a_groups[] = {
+ "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70",
+ "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77",
+ "gpio78", "gpio79",
+};
+
+static const char * const mdio_groups[] = {
+ "gpio65",
+};
+
+static const char * const pta2_0_groups[] = {
+ "gpio66",
+};
+
+static const char * const wci21_groups[] = {
+ "gpio66", "gpio68",
+};
+
+static const char * const cxc1_groups[] = {
+ "gpio66", "gpio68",
+};
+
+static const char * const pta2_1_groups[] = {
+ "gpio67",
+};
+
+static const char * const pta2_2_groups[] = {
+ "gpio68",
+};
+
+static const char * const blsp1_uart_groups[] = {
+ "gpio69", "gpio70", "gpio71", "gpio72",
+};
+
+static const char * const blsp1_i2c_groups[] = {
+ "gpio69", "gpio70",
+};
+
+static const char * const blsp1_spi_groups[] = {
+ "gpio69", "gpio70", "gpio71", "gpio72",
+};
+
+static const char * const gcc_plltest_groups[] = {
+ "gpio69", "gpio71",
+};
+
+static const char * const gcc_tlmm_groups[] = {
+ "gpio70",
+};
+
+static const char * const gpio_groups[] = {
+ "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7",
+ "gpio8", "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14",
+ "gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21",
+ "gpio22", "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28",
+ "gpio29", "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35",
+ "gpio36", "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45", "gpio46", "gpio47", "gpio48", "gpio49",
+ "gpio50", "gpio51", "gpio52", "gpio53", "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio58", "gpio59", "gpio60", "gpio61", "gpio62", "gpio63",
+ "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70",
+ "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77",
+ "gpio78", "gpio79",
+};
+
+static const struct msm_function ipq6018_functions[] = {
+ FUNCTION(atest_char),
+ FUNCTION(atest_char0),
+ FUNCTION(atest_char1),
+ FUNCTION(atest_char2),
+ FUNCTION(atest_char3),
+ FUNCTION(audio0),
+ FUNCTION(audio1),
+ FUNCTION(audio2),
+ FUNCTION(audio3),
+ FUNCTION(audio_rxbclk),
+ FUNCTION(audio_rxfsync),
+ FUNCTION(audio_rxmclk),
+ FUNCTION(audio_rxmclkin),
+ FUNCTION(audio_txbclk),
+ FUNCTION(audio_txfsync),
+ FUNCTION(audio_txmclk),
+ FUNCTION(audio_txmclkin),
+ FUNCTION(blsp0_i2c),
+ FUNCTION(blsp0_spi),
+ FUNCTION(blsp0_uart),
+ FUNCTION(blsp1_i2c),
+ FUNCTION(blsp1_spi),
+ FUNCTION(blsp1_uart),
+ FUNCTION(blsp2_i2c),
+ FUNCTION(blsp2_spi),
+ FUNCTION(blsp2_uart),
+ FUNCTION(blsp3_i2c),
+ FUNCTION(blsp3_spi),
+ FUNCTION(blsp3_uart),
+ FUNCTION(blsp4_i2c),
+ FUNCTION(blsp4_spi),
+ FUNCTION(blsp4_uart),
+ FUNCTION(blsp5_i2c),
+ FUNCTION(blsp5_uart),
+ FUNCTION(burn0),
+ FUNCTION(burn1),
+ FUNCTION(cri_trng),
+ FUNCTION(cri_trng0),
+ FUNCTION(cri_trng1),
+ FUNCTION(cxc0),
+ FUNCTION(cxc1),
+ FUNCTION(dbg_out),
+ FUNCTION(gcc_plltest),
+ FUNCTION(gcc_tlmm),
+ FUNCTION(gpio),
+ FUNCTION(lpass_aud),
+ FUNCTION(lpass_aud0),
+ FUNCTION(lpass_aud1),
+ FUNCTION(lpass_aud2),
+ FUNCTION(lpass_pcm),
+ FUNCTION(lpass_pdm),
+ FUNCTION(mac00),
+ FUNCTION(mac01),
+ FUNCTION(mac10),
+ FUNCTION(mac11),
+ FUNCTION(mac12),
+ FUNCTION(mac13),
+ FUNCTION(mac20),
+ FUNCTION(mac21),
+ FUNCTION(mdc),
+ FUNCTION(mdio),
+ FUNCTION(pcie0_clk),
+ FUNCTION(pcie0_rst),
+ FUNCTION(pcie0_wake),
+ FUNCTION(prng_rosc),
+ FUNCTION(pta1_0),
+ FUNCTION(pta1_1),
+ FUNCTION(pta1_2),
+ FUNCTION(pta2_0),
+ FUNCTION(pta2_1),
+ FUNCTION(pta2_2),
+ FUNCTION(pwm00),
+ FUNCTION(pwm01),
+ FUNCTION(pwm02),
+ FUNCTION(pwm03),
+ FUNCTION(pwm04),
+ FUNCTION(pwm10),
+ FUNCTION(pwm11),
+ FUNCTION(pwm12),
+ FUNCTION(pwm13),
+ FUNCTION(pwm14),
+ FUNCTION(pwm20),
+ FUNCTION(pwm21),
+ FUNCTION(pwm22),
+ FUNCTION(pwm23),
+ FUNCTION(pwm24),
+ FUNCTION(pwm30),
+ FUNCTION(pwm31),
+ FUNCTION(pwm32),
+ FUNCTION(pwm33),
+ FUNCTION(qdss_cti_trig_in_a0),
+ FUNCTION(qdss_cti_trig_in_a1),
+ FUNCTION(qdss_cti_trig_out_a0),
+ FUNCTION(qdss_cti_trig_out_a1),
+ FUNCTION(qdss_cti_trig_in_b0),
+ FUNCTION(qdss_cti_trig_in_b1),
+ FUNCTION(qdss_cti_trig_out_b0),
+ FUNCTION(qdss_cti_trig_out_b1),
+ FUNCTION(qdss_traceclk_a),
+ FUNCTION(qdss_tracectl_a),
+ FUNCTION(qdss_tracedata_a),
+ FUNCTION(qdss_traceclk_b),
+ FUNCTION(qdss_tracectl_b),
+ FUNCTION(qdss_tracedata_b),
+ FUNCTION(qpic_pad),
+ FUNCTION(rx0),
+ FUNCTION(rx1),
+ FUNCTION(rx_swrm),
+ FUNCTION(rx_swrm0),
+ FUNCTION(rx_swrm1),
+ FUNCTION(sd_card),
+ FUNCTION(sd_write),
+ FUNCTION(tsens_max),
+ FUNCTION(tx_swrm),
+ FUNCTION(tx_swrm0),
+ FUNCTION(tx_swrm1),
+ FUNCTION(tx_swrm2),
+ FUNCTION(wci20),
+ FUNCTION(wci21),
+ FUNCTION(wci22),
+ FUNCTION(wci23),
+ FUNCTION(wsa_swrm),
+};
+
+static const struct msm_pingroup ipq6018_groups[] = {
+ PINGROUP(0, qpic_pad, wci20, qdss_traceclk_b, _, burn0, _, _, _, _),
+ PINGROUP(1, qpic_pad, mac12, qdss_tracectl_b, _, burn1, _, _, _, _),
+ PINGROUP(2, qpic_pad, wci20, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(3, qpic_pad, mac01, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(4, qpic_pad, mac01, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(5, qpic_pad, mac21, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(6, qpic_pad, mac21, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(7, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(8, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(9, qpic_pad, atest_char, cxc0, mac13, dbg_out, qdss_tracedata_b, _, _, _),
+ PINGROUP(10, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(11, qpic_pad, wci22, mac12, qdss_tracedata_b, _, _, _, _, _),
+ PINGROUP(12, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(13, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(14, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(15, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(16, qpic_pad, cxc0, mac13, qdss_tracedata_b, _, _, _, _, _),
+ PINGROUP(17, qpic_pad, qdss_tracedata_b, wci22, _, _, _, _, _, _),
+ PINGROUP(18, pwm00, atest_char0, wci23, mac11, _, _, _, _, _),
+ PINGROUP(19, pwm10, atest_char1, wci23, mac11, _, _, _, _, _),
+ PINGROUP(20, pwm20, atest_char2, _, _, _, _, _, _, _),
+ PINGROUP(21, pwm30, atest_char3, _, _, _, _, _, _, _),
+ PINGROUP(22, audio_txmclk, audio_txmclkin, pwm02, tx_swrm0, _, qdss_cti_trig_out_b0, _, _, _),
+ PINGROUP(23, audio_txbclk, pwm12, wsa_swrm, tx_swrm1, _, qdss_cti_trig_in_b0, _, _, _),
+ PINGROUP(24, audio_txfsync, pwm22, wsa_swrm, tx_swrm2, _, qdss_cti_trig_out_b1, _, _, _),
+ PINGROUP(25, audio0, pwm32, tx_swrm, _, qdss_cti_trig_in_b1, _, _, _, _),
+ PINGROUP(26, audio1, pwm04, _, _, _, _, _, _, _),
+ PINGROUP(27, audio2, pwm14, _, _, _, _, _, _, _),
+ PINGROUP(28, audio3, pwm24, _, _, _, _, _, _, _),
+ PINGROUP(29, audio_rxmclk, audio_rxmclkin, pwm03, lpass_pdm, lpass_aud, qdss_cti_trig_in_a1, _, _, _),
+ PINGROUP(30, audio_rxbclk, pwm13, lpass_pdm, lpass_aud0, rx_swrm, _, qdss_cti_trig_out_a1, _, _),
+ PINGROUP(31, audio_rxfsync, pwm23, lpass_pdm, lpass_aud1, rx_swrm0, _, qdss_cti_trig_in_a0, _, _),
+ PINGROUP(32, audio0, pwm33, lpass_pdm, lpass_aud2, rx_swrm1, _, qdss_cti_trig_out_a0, _, _),
+ PINGROUP(33, audio1, _, _, _, _, _, _, _, _),
+ PINGROUP(34, lpass_pcm, mac10, mac00, _, _, _, _, _, _),
+ PINGROUP(35, lpass_pcm, mac10, mac00, _, _, _, _, _, _),
+ PINGROUP(36, lpass_pcm, mac20, _, _, _, _, _, _, _),
+ PINGROUP(37, lpass_pcm, mac20, _, _, _, _, _, _, _),
+ PINGROUP(38, blsp0_uart, blsp0_i2c, blsp0_spi, _, _, _, _, _, _),
+ PINGROUP(39, blsp0_uart, blsp0_i2c, blsp0_spi, _, _, _, _, _, _),
+ PINGROUP(40, blsp0_uart, blsp0_spi, _, _, _, _, _, _, _),
+ PINGROUP(41, blsp0_uart, blsp0_spi, _, _, _, _, _, _, _),
+ PINGROUP(42, blsp2_uart, blsp2_i2c, blsp2_spi, _, _, _, _, _, _),
+ PINGROUP(43, blsp2_uart, blsp2_i2c, blsp2_spi, _, _, _, _, _, _),
+ PINGROUP(44, blsp2_uart, blsp2_spi, _, _, _, _, _, _, _),
+ PINGROUP(45, blsp2_uart, blsp2_spi, _, _, _, _, _, _, _),
+ PINGROUP(46, blsp5_i2c, _, _, _, _, _, _, _, _),
+ PINGROUP(47, blsp5_i2c, _, _, _, _, _, _, _, _),
+ PINGROUP(48, blsp5_uart, _, qdss_traceclk_a, _, _, _, _, _, _),
+ PINGROUP(49, blsp5_uart, _, qdss_tracectl_a, _, _, _, _, _, _),
+ PINGROUP(50, pwm01, _, _, _, _, _, _, _, _),
+ PINGROUP(51, pta1_1, pwm11, _, rx1, _, _, _, _, _),
+ PINGROUP(52, pta1_2, pwm21, _, _, _, _, _, _, _),
+ PINGROUP(53, pta1_0, pwm31, prng_rosc, _, _, _, _, _, _),
+ PINGROUP(54, _, _, _, _, _, _, _, _, _),
+ PINGROUP(55, blsp4_uart, blsp4_i2c, blsp4_spi, _, _, _, _, _, _),
+ PINGROUP(56, blsp4_uart, blsp4_i2c, blsp4_spi, _, _, _, _, _, _),
+ PINGROUP(57, blsp4_uart, blsp4_spi, _, _, _, _, _, _, _),
+ PINGROUP(58, blsp4_uart, blsp4_spi, _, _, _, _, _, _, _),
+ PINGROUP(59, pcie0_clk, _, _, cri_trng0, _, _, _, _, _),
+ PINGROUP(60, pcie0_rst, _, _, cri_trng1, _, _, _, _, _),
+ PINGROUP(61, pcie0_wake, _, _, cri_trng, _, _, _, _, _),
+ PINGROUP(62, sd_card, _, _, _, _, _, _, _, _),
+ PINGROUP(63, sd_write, rx0, _, tsens_max, _, _, _, _, _),
+ PINGROUP(64, mdc, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(65, mdio, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(66, pta2_0, wci21, cxc1, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(67, pta2_1, qdss_tracedata_a, _, _, _, _, _, _, _),
+ PINGROUP(68, pta2_2, wci21, cxc1, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(69, blsp1_uart, blsp1_i2c, blsp1_spi, gcc_plltest, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(70, blsp1_uart, blsp1_i2c, blsp1_spi, gcc_tlmm, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(71, blsp1_uart, blsp1_spi, gcc_plltest, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(72, blsp1_uart, blsp1_spi, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(73, blsp3_uart, blsp3_i2c, blsp3_spi, _, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(74, blsp3_uart, blsp3_i2c, blsp3_spi, _, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(75, blsp3_uart, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(76, blsp3_uart, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(77, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(78, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(79, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
+};
+
+static const struct msm_pinctrl_soc_data ipq6018_pinctrl = {
+ .pins = ipq6018_pins,
+ .npins = ARRAY_SIZE(ipq6018_pins),
+ .functions = ipq6018_functions,
+ .nfunctions = ARRAY_SIZE(ipq6018_functions),
+ .groups = ipq6018_groups,
+ .ngroups = ARRAY_SIZE(ipq6018_groups),
+ .ngpios = 80,
+};
+
+static int ipq6018_pinctrl_probe(struct platform_device *pdev)
+{
+ return msm_pinctrl_probe(pdev, &ipq6018_pinctrl);
+}
+
+static const struct of_device_id ipq6018_pinctrl_of_match[] = {
+ { .compatible = "qcom,ipq6018-pinctrl", },
+ { },
+};
+
+static struct platform_driver ipq6018_pinctrl_driver = {
+ .driver = {
+ .name = "ipq6018-pinctrl",
+ .of_match_table = ipq6018_pinctrl_of_match,
+ },
+ .probe = ipq6018_pinctrl_probe,
+ .remove = msm_pinctrl_remove,
+};
+
+static int __init ipq6018_pinctrl_init(void)
+{
+ return platform_driver_register(&ipq6018_pinctrl_driver);
+}
+arch_initcall(ipq6018_pinctrl_init);
+
+static void __exit ipq6018_pinctrl_exit(void)
+{
+ platform_driver_unregister(&ipq6018_pinctrl_driver);
+}
+module_exit(ipq6018_pinctrl_exit);
+
+MODULE_DESCRIPTION("QTI ipq6018 pinctrl driver");
+MODULE_LICENSE("GPL v2");
+MODULE_DEVICE_TABLE(of, ipq6018_pinctrl_of_match);
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH V5 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver
@ 2020-01-16 7:44 ` Sricharan R
0 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
Cc: Selvam Sathappan Periakaruppan, Rajkumar Ayyasamy
Add initial pinctrl driver to support pin configuration with
pinctrl framework for ipq6018.
Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
drivers/pinctrl/qcom/Kconfig | 10 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-ipq6018.c | 1107 ++++++++++++++++++++++++++++++++
3 files changed, 1118 insertions(+)
create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq6018.c
diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
index 811af2f8..c5d4428 100644
--- a/drivers/pinctrl/qcom/Kconfig
+++ b/drivers/pinctrl/qcom/Kconfig
@@ -50,6 +50,16 @@ config PINCTRL_IPQ8074
Qualcomm Technologies Inc. IPQ8074 platform. Select this for
IPQ8074.
+config PINCTRL_IPQ6018
+ tristate "Qualcomm Technologies, Inc. IPQ6018 pin controller driver"
+ depends on GPIOLIB && OF
+ select PINCTRL_MSM
+ help
+ This is the pinctrl, pinmux, pinconf and gpiolib driver for
+ the Qualcomm Technologies Inc. TLMM block found on the
+ Qualcomm Technologies Inc. IPQ6018 platform. Select this for
+ IPQ6018.
+
config PINCTRL_MSM8660
tristate "Qualcomm 8660 pin controller driver"
depends on GPIOLIB && OF
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index c2c2f9a..d9e0904 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -6,6 +6,7 @@ obj-$(CONFIG_PINCTRL_APQ8084) += pinctrl-apq8084.o
obj-$(CONFIG_PINCTRL_IPQ4019) += pinctrl-ipq4019.o
obj-$(CONFIG_PINCTRL_IPQ8064) += pinctrl-ipq8064.o
obj-$(CONFIG_PINCTRL_IPQ8074) += pinctrl-ipq8074.o
+obj-$(CONFIG_PINCTRL_IPQ6018) += pinctrl-ipq6018.o
obj-$(CONFIG_PINCTRL_MSM8660) += pinctrl-msm8660.o
obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o
obj-$(CONFIG_PINCTRL_MSM8X74) += pinctrl-msm8x74.o
diff --git a/drivers/pinctrl/qcom/pinctrl-ipq6018.c b/drivers/pinctrl/qcom/pinctrl-ipq6018.c
new file mode 100644
index 0000000..38c33a7
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-ipq6018.c
@@ -0,0 +1,1107 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-msm.h"
+
+#define FUNCTION(fname) \
+ [msm_mux_##fname] = { \
+ .name = #fname, \
+ .groups = fname##_groups, \
+ .ngroups = ARRAY_SIZE(fname##_groups), \
+ }
+
+#define REG_SIZE 0x1000
+#define PINGROUP(id, f1, f2, f3, f4, f5, f6, f7, f8, f9) \
+ { \
+ .name = "gpio" #id, \
+ .pins = gpio##id##_pins, \
+ .npins = (unsigned int)ARRAY_SIZE(gpio##id##_pins), \
+ .funcs = (int[]){ \
+ msm_mux_gpio, /* gpio mode */ \
+ msm_mux_##f1, \
+ msm_mux_##f2, \
+ msm_mux_##f3, \
+ msm_mux_##f4, \
+ msm_mux_##f5, \
+ msm_mux_##f6, \
+ msm_mux_##f7, \
+ msm_mux_##f8, \
+ msm_mux_##f9 \
+ }, \
+ .nfuncs = 10, \
+ .ctl_reg = REG_SIZE * id, \
+ .io_reg = 0x4 + REG_SIZE * id, \
+ .intr_cfg_reg = 0x8 + REG_SIZE * id, \
+ .intr_status_reg = 0xc + REG_SIZE * id, \
+ .intr_target_reg = 0x8 + REG_SIZE * id, \
+ .mux_bit = 2, \
+ .pull_bit = 0, \
+ .drv_bit = 6, \
+ .oe_bit = 9, \
+ .in_bit = 0, \
+ .out_bit = 1, \
+ .intr_enable_bit = 0, \
+ .intr_status_bit = 0, \
+ .intr_target_bit = 5, \
+ .intr_target_kpss_val = 3, \
+ .intr_raw_status_bit = 4, \
+ .intr_polarity_bit = 1, \
+ .intr_detection_bit = 2, \
+ .intr_detection_width = 2, \
+ }
+
+static const struct pinctrl_pin_desc ipq6018_pins[] = {
+ PINCTRL_PIN(0, "GPIO_0"),
+ PINCTRL_PIN(1, "GPIO_1"),
+ PINCTRL_PIN(2, "GPIO_2"),
+ PINCTRL_PIN(3, "GPIO_3"),
+ PINCTRL_PIN(4, "GPIO_4"),
+ PINCTRL_PIN(5, "GPIO_5"),
+ PINCTRL_PIN(6, "GPIO_6"),
+ PINCTRL_PIN(7, "GPIO_7"),
+ PINCTRL_PIN(8, "GPIO_8"),
+ PINCTRL_PIN(9, "GPIO_9"),
+ PINCTRL_PIN(10, "GPIO_10"),
+ PINCTRL_PIN(11, "GPIO_11"),
+ PINCTRL_PIN(12, "GPIO_12"),
+ PINCTRL_PIN(13, "GPIO_13"),
+ PINCTRL_PIN(14, "GPIO_14"),
+ PINCTRL_PIN(15, "GPIO_15"),
+ PINCTRL_PIN(16, "GPIO_16"),
+ PINCTRL_PIN(17, "GPIO_17"),
+ PINCTRL_PIN(18, "GPIO_18"),
+ PINCTRL_PIN(19, "GPIO_19"),
+ PINCTRL_PIN(20, "GPIO_20"),
+ PINCTRL_PIN(21, "GPIO_21"),
+ PINCTRL_PIN(22, "GPIO_22"),
+ PINCTRL_PIN(23, "GPIO_23"),
+ PINCTRL_PIN(24, "GPIO_24"),
+ PINCTRL_PIN(25, "GPIO_25"),
+ PINCTRL_PIN(26, "GPIO_26"),
+ PINCTRL_PIN(27, "GPIO_27"),
+ PINCTRL_PIN(28, "GPIO_28"),
+ PINCTRL_PIN(29, "GPIO_29"),
+ PINCTRL_PIN(30, "GPIO_30"),
+ PINCTRL_PIN(31, "GPIO_31"),
+ PINCTRL_PIN(32, "GPIO_32"),
+ PINCTRL_PIN(33, "GPIO_33"),
+ PINCTRL_PIN(34, "GPIO_34"),
+ PINCTRL_PIN(35, "GPIO_35"),
+ PINCTRL_PIN(36, "GPIO_36"),
+ PINCTRL_PIN(37, "GPIO_37"),
+ PINCTRL_PIN(38, "GPIO_38"),
+ PINCTRL_PIN(39, "GPIO_39"),
+ PINCTRL_PIN(40, "GPIO_40"),
+ PINCTRL_PIN(41, "GPIO_41"),
+ PINCTRL_PIN(42, "GPIO_42"),
+ PINCTRL_PIN(43, "GPIO_43"),
+ PINCTRL_PIN(44, "GPIO_44"),
+ PINCTRL_PIN(45, "GPIO_45"),
+ PINCTRL_PIN(46, "GPIO_46"),
+ PINCTRL_PIN(47, "GPIO_47"),
+ PINCTRL_PIN(48, "GPIO_48"),
+ PINCTRL_PIN(49, "GPIO_49"),
+ PINCTRL_PIN(50, "GPIO_50"),
+ PINCTRL_PIN(51, "GPIO_51"),
+ PINCTRL_PIN(52, "GPIO_52"),
+ PINCTRL_PIN(53, "GPIO_53"),
+ PINCTRL_PIN(54, "GPIO_54"),
+ PINCTRL_PIN(55, "GPIO_55"),
+ PINCTRL_PIN(56, "GPIO_56"),
+ PINCTRL_PIN(57, "GPIO_57"),
+ PINCTRL_PIN(58, "GPIO_58"),
+ PINCTRL_PIN(59, "GPIO_59"),
+ PINCTRL_PIN(60, "GPIO_60"),
+ PINCTRL_PIN(61, "GPIO_61"),
+ PINCTRL_PIN(62, "GPIO_62"),
+ PINCTRL_PIN(63, "GPIO_63"),
+ PINCTRL_PIN(64, "GPIO_64"),
+ PINCTRL_PIN(65, "GPIO_65"),
+ PINCTRL_PIN(66, "GPIO_66"),
+ PINCTRL_PIN(67, "GPIO_67"),
+ PINCTRL_PIN(68, "GPIO_68"),
+ PINCTRL_PIN(69, "GPIO_69"),
+ PINCTRL_PIN(70, "GPIO_70"),
+ PINCTRL_PIN(71, "GPIO_71"),
+ PINCTRL_PIN(72, "GPIO_72"),
+ PINCTRL_PIN(73, "GPIO_73"),
+ PINCTRL_PIN(74, "GPIO_74"),
+ PINCTRL_PIN(75, "GPIO_75"),
+ PINCTRL_PIN(76, "GPIO_76"),
+ PINCTRL_PIN(77, "GPIO_77"),
+ PINCTRL_PIN(78, "GPIO_78"),
+ PINCTRL_PIN(79, "GPIO_79"),
+};
+
+#define DECLARE_MSM_GPIO_PINS(pin) \
+ static const unsigned int gpio##pin##_pins[] = { pin }
+DECLARE_MSM_GPIO_PINS(0);
+DECLARE_MSM_GPIO_PINS(1);
+DECLARE_MSM_GPIO_PINS(2);
+DECLARE_MSM_GPIO_PINS(3);
+DECLARE_MSM_GPIO_PINS(4);
+DECLARE_MSM_GPIO_PINS(5);
+DECLARE_MSM_GPIO_PINS(6);
+DECLARE_MSM_GPIO_PINS(7);
+DECLARE_MSM_GPIO_PINS(8);
+DECLARE_MSM_GPIO_PINS(9);
+DECLARE_MSM_GPIO_PINS(10);
+DECLARE_MSM_GPIO_PINS(11);
+DECLARE_MSM_GPIO_PINS(12);
+DECLARE_MSM_GPIO_PINS(13);
+DECLARE_MSM_GPIO_PINS(14);
+DECLARE_MSM_GPIO_PINS(15);
+DECLARE_MSM_GPIO_PINS(16);
+DECLARE_MSM_GPIO_PINS(17);
+DECLARE_MSM_GPIO_PINS(18);
+DECLARE_MSM_GPIO_PINS(19);
+DECLARE_MSM_GPIO_PINS(20);
+DECLARE_MSM_GPIO_PINS(21);
+DECLARE_MSM_GPIO_PINS(22);
+DECLARE_MSM_GPIO_PINS(23);
+DECLARE_MSM_GPIO_PINS(24);
+DECLARE_MSM_GPIO_PINS(25);
+DECLARE_MSM_GPIO_PINS(26);
+DECLARE_MSM_GPIO_PINS(27);
+DECLARE_MSM_GPIO_PINS(28);
+DECLARE_MSM_GPIO_PINS(29);
+DECLARE_MSM_GPIO_PINS(30);
+DECLARE_MSM_GPIO_PINS(31);
+DECLARE_MSM_GPIO_PINS(32);
+DECLARE_MSM_GPIO_PINS(33);
+DECLARE_MSM_GPIO_PINS(34);
+DECLARE_MSM_GPIO_PINS(35);
+DECLARE_MSM_GPIO_PINS(36);
+DECLARE_MSM_GPIO_PINS(37);
+DECLARE_MSM_GPIO_PINS(38);
+DECLARE_MSM_GPIO_PINS(39);
+DECLARE_MSM_GPIO_PINS(40);
+DECLARE_MSM_GPIO_PINS(41);
+DECLARE_MSM_GPIO_PINS(42);
+DECLARE_MSM_GPIO_PINS(43);
+DECLARE_MSM_GPIO_PINS(44);
+DECLARE_MSM_GPIO_PINS(45);
+DECLARE_MSM_GPIO_PINS(46);
+DECLARE_MSM_GPIO_PINS(47);
+DECLARE_MSM_GPIO_PINS(48);
+DECLARE_MSM_GPIO_PINS(49);
+DECLARE_MSM_GPIO_PINS(50);
+DECLARE_MSM_GPIO_PINS(51);
+DECLARE_MSM_GPIO_PINS(52);
+DECLARE_MSM_GPIO_PINS(53);
+DECLARE_MSM_GPIO_PINS(54);
+DECLARE_MSM_GPIO_PINS(55);
+DECLARE_MSM_GPIO_PINS(56);
+DECLARE_MSM_GPIO_PINS(57);
+DECLARE_MSM_GPIO_PINS(58);
+DECLARE_MSM_GPIO_PINS(59);
+DECLARE_MSM_GPIO_PINS(60);
+DECLARE_MSM_GPIO_PINS(61);
+DECLARE_MSM_GPIO_PINS(62);
+DECLARE_MSM_GPIO_PINS(63);
+DECLARE_MSM_GPIO_PINS(64);
+DECLARE_MSM_GPIO_PINS(65);
+DECLARE_MSM_GPIO_PINS(66);
+DECLARE_MSM_GPIO_PINS(67);
+DECLARE_MSM_GPIO_PINS(68);
+DECLARE_MSM_GPIO_PINS(69);
+DECLARE_MSM_GPIO_PINS(70);
+DECLARE_MSM_GPIO_PINS(71);
+DECLARE_MSM_GPIO_PINS(72);
+DECLARE_MSM_GPIO_PINS(73);
+DECLARE_MSM_GPIO_PINS(74);
+DECLARE_MSM_GPIO_PINS(75);
+DECLARE_MSM_GPIO_PINS(76);
+DECLARE_MSM_GPIO_PINS(77);
+DECLARE_MSM_GPIO_PINS(78);
+DECLARE_MSM_GPIO_PINS(79);
+
+enum ipq6018_functions {
+ msm_mux_atest_char,
+ msm_mux_atest_char0,
+ msm_mux_atest_char1,
+ msm_mux_atest_char2,
+ msm_mux_atest_char3,
+ msm_mux_audio0,
+ msm_mux_audio1,
+ msm_mux_audio2,
+ msm_mux_audio3,
+ msm_mux_audio_rxbclk,
+ msm_mux_audio_rxfsync,
+ msm_mux_audio_rxmclk,
+ msm_mux_audio_rxmclkin,
+ msm_mux_audio_txbclk,
+ msm_mux_audio_txfsync,
+ msm_mux_audio_txmclk,
+ msm_mux_audio_txmclkin,
+ msm_mux_blsp0_i2c,
+ msm_mux_blsp0_spi,
+ msm_mux_blsp0_uart,
+ msm_mux_blsp1_i2c,
+ msm_mux_blsp1_spi,
+ msm_mux_blsp1_uart,
+ msm_mux_blsp2_i2c,
+ msm_mux_blsp2_spi,
+ msm_mux_blsp2_uart,
+ msm_mux_blsp3_i2c,
+ msm_mux_blsp3_spi,
+ msm_mux_blsp3_uart,
+ msm_mux_blsp4_i2c,
+ msm_mux_blsp4_spi,
+ msm_mux_blsp4_uart,
+ msm_mux_blsp5_i2c,
+ msm_mux_blsp5_uart,
+ msm_mux_burn0,
+ msm_mux_burn1,
+ msm_mux_cri_trng,
+ msm_mux_cri_trng0,
+ msm_mux_cri_trng1,
+ msm_mux_cxc0,
+ msm_mux_cxc1,
+ msm_mux_dbg_out,
+ msm_mux_gcc_plltest,
+ msm_mux_gcc_tlmm,
+ msm_mux_gpio,
+ msm_mux_lpass_aud,
+ msm_mux_lpass_aud0,
+ msm_mux_lpass_aud1,
+ msm_mux_lpass_aud2,
+ msm_mux_lpass_pcm,
+ msm_mux_lpass_pdm,
+ msm_mux_mac00,
+ msm_mux_mac01,
+ msm_mux_mac10,
+ msm_mux_mac11,
+ msm_mux_mac12,
+ msm_mux_mac13,
+ msm_mux_mac20,
+ msm_mux_mac21,
+ msm_mux_mdc,
+ msm_mux_mdio,
+ msm_mux_pcie0_clk,
+ msm_mux_pcie0_rst,
+ msm_mux_pcie0_wake,
+ msm_mux_prng_rosc,
+ msm_mux_pta1_0,
+ msm_mux_pta1_1,
+ msm_mux_pta1_2,
+ msm_mux_pta2_0,
+ msm_mux_pta2_1,
+ msm_mux_pta2_2,
+ msm_mux_pwm00,
+ msm_mux_pwm01,
+ msm_mux_pwm02,
+ msm_mux_pwm03,
+ msm_mux_pwm04,
+ msm_mux_pwm10,
+ msm_mux_pwm11,
+ msm_mux_pwm12,
+ msm_mux_pwm13,
+ msm_mux_pwm14,
+ msm_mux_pwm20,
+ msm_mux_pwm21,
+ msm_mux_pwm22,
+ msm_mux_pwm23,
+ msm_mux_pwm24,
+ msm_mux_pwm30,
+ msm_mux_pwm31,
+ msm_mux_pwm32,
+ msm_mux_pwm33,
+ msm_mux_qdss_cti_trig_in_a0,
+ msm_mux_qdss_cti_trig_in_a1,
+ msm_mux_qdss_cti_trig_out_a0,
+ msm_mux_qdss_cti_trig_out_a1,
+ msm_mux_qdss_cti_trig_in_b0,
+ msm_mux_qdss_cti_trig_in_b1,
+ msm_mux_qdss_cti_trig_out_b0,
+ msm_mux_qdss_cti_trig_out_b1,
+ msm_mux_qdss_traceclk_a,
+ msm_mux_qdss_tracectl_a,
+ msm_mux_qdss_tracedata_a,
+ msm_mux_qdss_traceclk_b,
+ msm_mux_qdss_tracectl_b,
+ msm_mux_qdss_tracedata_b,
+ msm_mux_qpic_pad,
+ msm_mux_rx0,
+ msm_mux_rx1,
+ msm_mux_rx_swrm,
+ msm_mux_rx_swrm0,
+ msm_mux_rx_swrm1,
+ msm_mux_sd_card,
+ msm_mux_sd_write,
+ msm_mux_tsens_max,
+ msm_mux_tx_swrm,
+ msm_mux_tx_swrm0,
+ msm_mux_tx_swrm1,
+ msm_mux_tx_swrm2,
+ msm_mux_wci20,
+ msm_mux_wci21,
+ msm_mux_wci22,
+ msm_mux_wci23,
+ msm_mux_wsa_swrm,
+ msm_mux__,
+};
+
+static const char * const blsp3_uart_groups[] = {
+ "gpio73", "gpio74", "gpio75", "gpio76",
+};
+
+static const char * const blsp3_i2c_groups[] = {
+ "gpio73", "gpio74",
+};
+
+static const char * const blsp3_spi_groups[] = {
+ "gpio73", "gpio74", "gpio75", "gpio76", "gpio77", "gpio78", "gpio79",
+};
+
+static const char * const wci20_groups[] = {
+ "gpio0", "gpio2",
+};
+
+static const char * const qpic_pad_groups[] = {
+ "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio9", "gpio10",
+ "gpio11", "gpio17",
+};
+
+static const char * const burn0_groups[] = {
+ "gpio0",
+};
+
+static const char * const mac12_groups[] = {
+ "gpio1", "gpio11",
+};
+
+static const char * const qdss_tracectl_b_groups[] = {
+ "gpio1",
+};
+
+static const char * const burn1_groups[] = {
+ "gpio1",
+};
+
+static const char * const qdss_traceclk_b_groups[] = {
+ "gpio0",
+};
+
+static const char * const qdss_tracedata_b_groups[] = {
+ "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8", "gpio9",
+ "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15", "gpio16",
+ "gpio17",
+};
+
+static const char * const mac01_groups[] = {
+ "gpio3", "gpio4",
+};
+
+static const char * const mac21_groups[] = {
+ "gpio5", "gpio6",
+};
+
+static const char * const atest_char_groups[] = {
+ "gpio9",
+};
+
+static const char * const cxc0_groups[] = {
+ "gpio9", "gpio16",
+};
+
+static const char * const mac13_groups[] = {
+ "gpio9", "gpio16",
+};
+
+static const char * const dbg_out_groups[] = {
+ "gpio9",
+};
+
+static const char * const wci22_groups[] = {
+ "gpio11", "gpio17",
+};
+
+static const char * const pwm00_groups[] = {
+ "gpio18",
+};
+
+static const char * const atest_char0_groups[] = {
+ "gpio18",
+};
+
+static const char * const wci23_groups[] = {
+ "gpio18", "gpio19",
+};
+
+static const char * const mac11_groups[] = {
+ "gpio18", "gpio19",
+};
+
+static const char * const pwm10_groups[] = {
+ "gpio19",
+};
+
+static const char * const atest_char1_groups[] = {
+ "gpio19",
+};
+
+static const char * const pwm20_groups[] = {
+ "gpio20",
+};
+
+static const char * const atest_char2_groups[] = {
+ "gpio20",
+};
+
+static const char * const pwm30_groups[] = {
+ "gpio21",
+};
+
+static const char * const atest_char3_groups[] = {
+ "gpio21",
+};
+
+static const char * const audio_txmclk_groups[] = {
+ "gpio22",
+};
+
+static const char * const audio_txmclkin_groups[] = {
+ "gpio22",
+};
+
+static const char * const pwm02_groups[] = {
+ "gpio22",
+};
+
+static const char * const tx_swrm0_groups[] = {
+ "gpio22",
+};
+
+static const char * const qdss_cti_trig_out_b0_groups[] = {
+ "gpio22",
+};
+
+static const char * const audio_txbclk_groups[] = {
+ "gpio23",
+};
+
+static const char * const pwm12_groups[] = {
+ "gpio23",
+};
+
+static const char * const wsa_swrm_groups[] = {
+ "gpio23", "gpio24",
+};
+
+static const char * const tx_swrm1_groups[] = {
+ "gpio23",
+};
+
+static const char * const qdss_cti_trig_in_b0_groups[] = {
+ "gpio23",
+};
+
+static const char * const audio_txfsync_groups[] = {
+ "gpio24",
+};
+
+static const char * const pwm22_groups[] = {
+ "gpio24",
+};
+
+static const char * const tx_swrm2_groups[] = {
+ "gpio24",
+};
+
+static const char * const qdss_cti_trig_out_b1_groups[] = {
+ "gpio24",
+};
+
+static const char * const audio0_groups[] = {
+ "gpio25", "gpio32",
+};
+
+static const char * const pwm32_groups[] = {
+ "gpio25",
+};
+
+static const char * const tx_swrm_groups[] = {
+ "gpio25",
+};
+
+static const char * const qdss_cti_trig_in_b1_groups[] = {
+ "gpio25",
+};
+
+static const char * const audio1_groups[] = {
+ "gpio26", "gpio33",
+};
+
+static const char * const pwm04_groups[] = {
+ "gpio26",
+};
+
+static const char * const audio2_groups[] = {
+ "gpio27",
+};
+
+static const char * const pwm14_groups[] = {
+ "gpio27",
+};
+
+static const char * const audio3_groups[] = {
+ "gpio28",
+};
+
+static const char * const pwm24_groups[] = {
+ "gpio28",
+};
+
+static const char * const audio_rxmclk_groups[] = {
+ "gpio29",
+};
+
+static const char * const audio_rxmclkin_groups[] = {
+ "gpio29",
+};
+
+static const char * const pwm03_groups[] = {
+ "gpio29",
+};
+
+static const char * const lpass_pdm_groups[] = {
+ "gpio29", "gpio30", "gpio31", "gpio32",
+};
+
+static const char * const lpass_aud_groups[] = {
+ "gpio29",
+};
+
+static const char * const qdss_cti_trig_in_a1_groups[] = {
+ "gpio29",
+};
+
+static const char * const audio_rxbclk_groups[] = {
+ "gpio30",
+};
+
+static const char * const pwm13_groups[] = {
+ "gpio30",
+};
+
+static const char * const lpass_aud0_groups[] = {
+ "gpio30",
+};
+
+static const char * const rx_swrm_groups[] = {
+ "gpio30",
+};
+
+static const char * const qdss_cti_trig_out_a1_groups[] = {
+ "gpio30",
+};
+
+static const char * const audio_rxfsync_groups[] = {
+ "gpio31",
+};
+
+static const char * const pwm23_groups[] = {
+ "gpio31",
+};
+
+static const char * const lpass_aud1_groups[] = {
+ "gpio31",
+};
+
+static const char * const rx_swrm0_groups[] = {
+ "gpio31",
+};
+
+static const char * const qdss_cti_trig_in_a0_groups[] = {
+ "gpio31",
+};
+
+static const char * const pwm33_groups[] = {
+ "gpio32",
+};
+
+static const char * const lpass_aud2_groups[] = {
+ "gpio32",
+};
+
+static const char * const rx_swrm1_groups[] = {
+ "gpio32",
+};
+
+static const char * const qdss_cti_trig_out_a0_groups[] = {
+ "gpio32",
+};
+
+static const char * const lpass_pcm_groups[] = {
+ "gpio34", "gpio35", "gpio36", "gpio37",
+};
+
+static const char * const mac10_groups[] = {
+ "gpio34", "gpio35",
+};
+
+static const char * const mac00_groups[] = {
+ "gpio34", "gpio35",
+};
+
+static const char * const mac20_groups[] = {
+ "gpio36", "gpio37",
+};
+
+static const char * const blsp0_uart_groups[] = {
+ "gpio38", "gpio39", "gpio40", "gpio41",
+};
+
+static const char * const blsp0_i2c_groups[] = {
+ "gpio38", "gpio39",
+};
+
+static const char * const blsp0_spi_groups[] = {
+ "gpio38", "gpio39", "gpio40", "gpio41",
+};
+
+static const char * const blsp2_uart_groups[] = {
+ "gpio42", "gpio43", "gpio44", "gpio45",
+};
+
+static const char * const blsp2_i2c_groups[] = {
+ "gpio42", "gpio43",
+};
+
+static const char * const blsp2_spi_groups[] = {
+ "gpio42", "gpio43", "gpio44", "gpio45",
+};
+
+static const char * const blsp5_i2c_groups[] = {
+ "gpio46", "gpio47",
+};
+
+static const char * const blsp5_uart_groups[] = {
+ "gpio48", "gpio49",
+};
+
+static const char * const qdss_traceclk_a_groups[] = {
+ "gpio48",
+};
+
+static const char * const qdss_tracectl_a_groups[] = {
+ "gpio49",
+};
+
+static const char * const pwm01_groups[] = {
+ "gpio50",
+};
+
+static const char * const pta1_1_groups[] = {
+ "gpio51",
+};
+
+static const char * const pwm11_groups[] = {
+ "gpio51",
+};
+
+static const char * const rx1_groups[] = {
+ "gpio51",
+};
+
+static const char * const pta1_2_groups[] = {
+ "gpio52",
+};
+
+static const char * const pwm21_groups[] = {
+ "gpio52",
+};
+
+static const char * const pta1_0_groups[] = {
+ "gpio53",
+};
+
+static const char * const pwm31_groups[] = {
+ "gpio53",
+};
+
+static const char * const prng_rosc_groups[] = {
+ "gpio53",
+};
+
+static const char * const blsp4_uart_groups[] = {
+ "gpio55", "gpio56", "gpio57", "gpio58",
+};
+
+static const char * const blsp4_i2c_groups[] = {
+ "gpio55", "gpio56",
+};
+
+static const char * const blsp4_spi_groups[] = {
+ "gpio55", "gpio56", "gpio57", "gpio58",
+};
+
+static const char * const pcie0_clk_groups[] = {
+ "gpio59",
+};
+
+static const char * const cri_trng0_groups[] = {
+ "gpio59",
+};
+
+static const char * const pcie0_rst_groups[] = {
+ "gpio60",
+};
+
+static const char * const cri_trng1_groups[] = {
+ "gpio60",
+};
+
+static const char * const pcie0_wake_groups[] = {
+ "gpio61",
+};
+
+static const char * const cri_trng_groups[] = {
+ "gpio61",
+};
+
+static const char * const sd_card_groups[] = {
+ "gpio62",
+};
+
+static const char * const sd_write_groups[] = {
+ "gpio63",
+};
+
+static const char * const rx0_groups[] = {
+ "gpio63",
+};
+
+static const char * const tsens_max_groups[] = {
+ "gpio63",
+};
+
+static const char * const mdc_groups[] = {
+ "gpio64",
+};
+
+static const char * const qdss_tracedata_a_groups[] = {
+ "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70",
+ "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77",
+ "gpio78", "gpio79",
+};
+
+static const char * const mdio_groups[] = {
+ "gpio65",
+};
+
+static const char * const pta2_0_groups[] = {
+ "gpio66",
+};
+
+static const char * const wci21_groups[] = {
+ "gpio66", "gpio68",
+};
+
+static const char * const cxc1_groups[] = {
+ "gpio66", "gpio68",
+};
+
+static const char * const pta2_1_groups[] = {
+ "gpio67",
+};
+
+static const char * const pta2_2_groups[] = {
+ "gpio68",
+};
+
+static const char * const blsp1_uart_groups[] = {
+ "gpio69", "gpio70", "gpio71", "gpio72",
+};
+
+static const char * const blsp1_i2c_groups[] = {
+ "gpio69", "gpio70",
+};
+
+static const char * const blsp1_spi_groups[] = {
+ "gpio69", "gpio70", "gpio71", "gpio72",
+};
+
+static const char * const gcc_plltest_groups[] = {
+ "gpio69", "gpio71",
+};
+
+static const char * const gcc_tlmm_groups[] = {
+ "gpio70",
+};
+
+static const char * const gpio_groups[] = {
+ "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7",
+ "gpio8", "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14",
+ "gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21",
+ "gpio22", "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28",
+ "gpio29", "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35",
+ "gpio36", "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45", "gpio46", "gpio47", "gpio48", "gpio49",
+ "gpio50", "gpio51", "gpio52", "gpio53", "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio58", "gpio59", "gpio60", "gpio61", "gpio62", "gpio63",
+ "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70",
+ "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77",
+ "gpio78", "gpio79",
+};
+
+static const struct msm_function ipq6018_functions[] = {
+ FUNCTION(atest_char),
+ FUNCTION(atest_char0),
+ FUNCTION(atest_char1),
+ FUNCTION(atest_char2),
+ FUNCTION(atest_char3),
+ FUNCTION(audio0),
+ FUNCTION(audio1),
+ FUNCTION(audio2),
+ FUNCTION(audio3),
+ FUNCTION(audio_rxbclk),
+ FUNCTION(audio_rxfsync),
+ FUNCTION(audio_rxmclk),
+ FUNCTION(audio_rxmclkin),
+ FUNCTION(audio_txbclk),
+ FUNCTION(audio_txfsync),
+ FUNCTION(audio_txmclk),
+ FUNCTION(audio_txmclkin),
+ FUNCTION(blsp0_i2c),
+ FUNCTION(blsp0_spi),
+ FUNCTION(blsp0_uart),
+ FUNCTION(blsp1_i2c),
+ FUNCTION(blsp1_spi),
+ FUNCTION(blsp1_uart),
+ FUNCTION(blsp2_i2c),
+ FUNCTION(blsp2_spi),
+ FUNCTION(blsp2_uart),
+ FUNCTION(blsp3_i2c),
+ FUNCTION(blsp3_spi),
+ FUNCTION(blsp3_uart),
+ FUNCTION(blsp4_i2c),
+ FUNCTION(blsp4_spi),
+ FUNCTION(blsp4_uart),
+ FUNCTION(blsp5_i2c),
+ FUNCTION(blsp5_uart),
+ FUNCTION(burn0),
+ FUNCTION(burn1),
+ FUNCTION(cri_trng),
+ FUNCTION(cri_trng0),
+ FUNCTION(cri_trng1),
+ FUNCTION(cxc0),
+ FUNCTION(cxc1),
+ FUNCTION(dbg_out),
+ FUNCTION(gcc_plltest),
+ FUNCTION(gcc_tlmm),
+ FUNCTION(gpio),
+ FUNCTION(lpass_aud),
+ FUNCTION(lpass_aud0),
+ FUNCTION(lpass_aud1),
+ FUNCTION(lpass_aud2),
+ FUNCTION(lpass_pcm),
+ FUNCTION(lpass_pdm),
+ FUNCTION(mac00),
+ FUNCTION(mac01),
+ FUNCTION(mac10),
+ FUNCTION(mac11),
+ FUNCTION(mac12),
+ FUNCTION(mac13),
+ FUNCTION(mac20),
+ FUNCTION(mac21),
+ FUNCTION(mdc),
+ FUNCTION(mdio),
+ FUNCTION(pcie0_clk),
+ FUNCTION(pcie0_rst),
+ FUNCTION(pcie0_wake),
+ FUNCTION(prng_rosc),
+ FUNCTION(pta1_0),
+ FUNCTION(pta1_1),
+ FUNCTION(pta1_2),
+ FUNCTION(pta2_0),
+ FUNCTION(pta2_1),
+ FUNCTION(pta2_2),
+ FUNCTION(pwm00),
+ FUNCTION(pwm01),
+ FUNCTION(pwm02),
+ FUNCTION(pwm03),
+ FUNCTION(pwm04),
+ FUNCTION(pwm10),
+ FUNCTION(pwm11),
+ FUNCTION(pwm12),
+ FUNCTION(pwm13),
+ FUNCTION(pwm14),
+ FUNCTION(pwm20),
+ FUNCTION(pwm21),
+ FUNCTION(pwm22),
+ FUNCTION(pwm23),
+ FUNCTION(pwm24),
+ FUNCTION(pwm30),
+ FUNCTION(pwm31),
+ FUNCTION(pwm32),
+ FUNCTION(pwm33),
+ FUNCTION(qdss_cti_trig_in_a0),
+ FUNCTION(qdss_cti_trig_in_a1),
+ FUNCTION(qdss_cti_trig_out_a0),
+ FUNCTION(qdss_cti_trig_out_a1),
+ FUNCTION(qdss_cti_trig_in_b0),
+ FUNCTION(qdss_cti_trig_in_b1),
+ FUNCTION(qdss_cti_trig_out_b0),
+ FUNCTION(qdss_cti_trig_out_b1),
+ FUNCTION(qdss_traceclk_a),
+ FUNCTION(qdss_tracectl_a),
+ FUNCTION(qdss_tracedata_a),
+ FUNCTION(qdss_traceclk_b),
+ FUNCTION(qdss_tracectl_b),
+ FUNCTION(qdss_tracedata_b),
+ FUNCTION(qpic_pad),
+ FUNCTION(rx0),
+ FUNCTION(rx1),
+ FUNCTION(rx_swrm),
+ FUNCTION(rx_swrm0),
+ FUNCTION(rx_swrm1),
+ FUNCTION(sd_card),
+ FUNCTION(sd_write),
+ FUNCTION(tsens_max),
+ FUNCTION(tx_swrm),
+ FUNCTION(tx_swrm0),
+ FUNCTION(tx_swrm1),
+ FUNCTION(tx_swrm2),
+ FUNCTION(wci20),
+ FUNCTION(wci21),
+ FUNCTION(wci22),
+ FUNCTION(wci23),
+ FUNCTION(wsa_swrm),
+};
+
+static const struct msm_pingroup ipq6018_groups[] = {
+ PINGROUP(0, qpic_pad, wci20, qdss_traceclk_b, _, burn0, _, _, _, _),
+ PINGROUP(1, qpic_pad, mac12, qdss_tracectl_b, _, burn1, _, _, _, _),
+ PINGROUP(2, qpic_pad, wci20, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(3, qpic_pad, mac01, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(4, qpic_pad, mac01, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(5, qpic_pad, mac21, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(6, qpic_pad, mac21, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(7, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(8, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(9, qpic_pad, atest_char, cxc0, mac13, dbg_out, qdss_tracedata_b, _, _, _),
+ PINGROUP(10, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(11, qpic_pad, wci22, mac12, qdss_tracedata_b, _, _, _, _, _),
+ PINGROUP(12, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(13, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(14, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(15, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(16, qpic_pad, cxc0, mac13, qdss_tracedata_b, _, _, _, _, _),
+ PINGROUP(17, qpic_pad, qdss_tracedata_b, wci22, _, _, _, _, _, _),
+ PINGROUP(18, pwm00, atest_char0, wci23, mac11, _, _, _, _, _),
+ PINGROUP(19, pwm10, atest_char1, wci23, mac11, _, _, _, _, _),
+ PINGROUP(20, pwm20, atest_char2, _, _, _, _, _, _, _),
+ PINGROUP(21, pwm30, atest_char3, _, _, _, _, _, _, _),
+ PINGROUP(22, audio_txmclk, audio_txmclkin, pwm02, tx_swrm0, _, qdss_cti_trig_out_b0, _, _, _),
+ PINGROUP(23, audio_txbclk, pwm12, wsa_swrm, tx_swrm1, _, qdss_cti_trig_in_b0, _, _, _),
+ PINGROUP(24, audio_txfsync, pwm22, wsa_swrm, tx_swrm2, _, qdss_cti_trig_out_b1, _, _, _),
+ PINGROUP(25, audio0, pwm32, tx_swrm, _, qdss_cti_trig_in_b1, _, _, _, _),
+ PINGROUP(26, audio1, pwm04, _, _, _, _, _, _, _),
+ PINGROUP(27, audio2, pwm14, _, _, _, _, _, _, _),
+ PINGROUP(28, audio3, pwm24, _, _, _, _, _, _, _),
+ PINGROUP(29, audio_rxmclk, audio_rxmclkin, pwm03, lpass_pdm, lpass_aud, qdss_cti_trig_in_a1, _, _, _),
+ PINGROUP(30, audio_rxbclk, pwm13, lpass_pdm, lpass_aud0, rx_swrm, _, qdss_cti_trig_out_a1, _, _),
+ PINGROUP(31, audio_rxfsync, pwm23, lpass_pdm, lpass_aud1, rx_swrm0, _, qdss_cti_trig_in_a0, _, _),
+ PINGROUP(32, audio0, pwm33, lpass_pdm, lpass_aud2, rx_swrm1, _, qdss_cti_trig_out_a0, _, _),
+ PINGROUP(33, audio1, _, _, _, _, _, _, _, _),
+ PINGROUP(34, lpass_pcm, mac10, mac00, _, _, _, _, _, _),
+ PINGROUP(35, lpass_pcm, mac10, mac00, _, _, _, _, _, _),
+ PINGROUP(36, lpass_pcm, mac20, _, _, _, _, _, _, _),
+ PINGROUP(37, lpass_pcm, mac20, _, _, _, _, _, _, _),
+ PINGROUP(38, blsp0_uart, blsp0_i2c, blsp0_spi, _, _, _, _, _, _),
+ PINGROUP(39, blsp0_uart, blsp0_i2c, blsp0_spi, _, _, _, _, _, _),
+ PINGROUP(40, blsp0_uart, blsp0_spi, _, _, _, _, _, _, _),
+ PINGROUP(41, blsp0_uart, blsp0_spi, _, _, _, _, _, _, _),
+ PINGROUP(42, blsp2_uart, blsp2_i2c, blsp2_spi, _, _, _, _, _, _),
+ PINGROUP(43, blsp2_uart, blsp2_i2c, blsp2_spi, _, _, _, _, _, _),
+ PINGROUP(44, blsp2_uart, blsp2_spi, _, _, _, _, _, _, _),
+ PINGROUP(45, blsp2_uart, blsp2_spi, _, _, _, _, _, _, _),
+ PINGROUP(46, blsp5_i2c, _, _, _, _, _, _, _, _),
+ PINGROUP(47, blsp5_i2c, _, _, _, _, _, _, _, _),
+ PINGROUP(48, blsp5_uart, _, qdss_traceclk_a, _, _, _, _, _, _),
+ PINGROUP(49, blsp5_uart, _, qdss_tracectl_a, _, _, _, _, _, _),
+ PINGROUP(50, pwm01, _, _, _, _, _, _, _, _),
+ PINGROUP(51, pta1_1, pwm11, _, rx1, _, _, _, _, _),
+ PINGROUP(52, pta1_2, pwm21, _, _, _, _, _, _, _),
+ PINGROUP(53, pta1_0, pwm31, prng_rosc, _, _, _, _, _, _),
+ PINGROUP(54, _, _, _, _, _, _, _, _, _),
+ PINGROUP(55, blsp4_uart, blsp4_i2c, blsp4_spi, _, _, _, _, _, _),
+ PINGROUP(56, blsp4_uart, blsp4_i2c, blsp4_spi, _, _, _, _, _, _),
+ PINGROUP(57, blsp4_uart, blsp4_spi, _, _, _, _, _, _, _),
+ PINGROUP(58, blsp4_uart, blsp4_spi, _, _, _, _, _, _, _),
+ PINGROUP(59, pcie0_clk, _, _, cri_trng0, _, _, _, _, _),
+ PINGROUP(60, pcie0_rst, _, _, cri_trng1, _, _, _, _, _),
+ PINGROUP(61, pcie0_wake, _, _, cri_trng, _, _, _, _, _),
+ PINGROUP(62, sd_card, _, _, _, _, _, _, _, _),
+ PINGROUP(63, sd_write, rx0, _, tsens_max, _, _, _, _, _),
+ PINGROUP(64, mdc, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(65, mdio, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(66, pta2_0, wci21, cxc1, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(67, pta2_1, qdss_tracedata_a, _, _, _, _, _, _, _),
+ PINGROUP(68, pta2_2, wci21, cxc1, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(69, blsp1_uart, blsp1_i2c, blsp1_spi, gcc_plltest, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(70, blsp1_uart, blsp1_i2c, blsp1_spi, gcc_tlmm, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(71, blsp1_uart, blsp1_spi, gcc_plltest, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(72, blsp1_uart, blsp1_spi, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(73, blsp3_uart, blsp3_i2c, blsp3_spi, _, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(74, blsp3_uart, blsp3_i2c, blsp3_spi, _, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(75, blsp3_uart, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(76, blsp3_uart, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(77, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(78, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(79, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
+};
+
+static const struct msm_pinctrl_soc_data ipq6018_pinctrl = {
+ .pins = ipq6018_pins,
+ .npins = ARRAY_SIZE(ipq6018_pins),
+ .functions = ipq6018_functions,
+ .nfunctions = ARRAY_SIZE(ipq6018_functions),
+ .groups = ipq6018_groups,
+ .ngroups = ARRAY_SIZE(ipq6018_groups),
+ .ngpios = 80,
+};
+
+static int ipq6018_pinctrl_probe(struct platform_device *pdev)
+{
+ return msm_pinctrl_probe(pdev, &ipq6018_pinctrl);
+}
+
+static const struct of_device_id ipq6018_pinctrl_of_match[] = {
+ { .compatible = "qcom,ipq6018-pinctrl", },
+ { },
+};
+
+static struct platform_driver ipq6018_pinctrl_driver = {
+ .driver = {
+ .name = "ipq6018-pinctrl",
+ .of_match_table = ipq6018_pinctrl_of_match,
+ },
+ .probe = ipq6018_pinctrl_probe,
+ .remove = msm_pinctrl_remove,
+};
+
+static int __init ipq6018_pinctrl_init(void)
+{
+ return platform_driver_register(&ipq6018_pinctrl_driver);
+}
+arch_initcall(ipq6018_pinctrl_init);
+
+static void __exit ipq6018_pinctrl_exit(void)
+{
+ platform_driver_unregister(&ipq6018_pinctrl_driver);
+}
+module_exit(ipq6018_pinctrl_exit);
+
+MODULE_DESCRIPTION("QTI ipq6018 pinctrl driver");
+MODULE_LICENSE("GPL v2");
+MODULE_DEVICE_TABLE(of, ipq6018_pinctrl_of_match);
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH V5 3/5] dt-bindings: qcom: Add ipq6018 bindings
2020-01-16 7:44 ` Sricharan R
@ 2020-01-16 7:44 ` Sricharan R
-1 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
Cc: Selvam Sathappan Periakaruppan
Document the new ipq6018 SOC/board device tree bindings.
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 529d924..164177e 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -28,6 +28,7 @@ description: |
apq8074
apq8084
apq8096
+ ipq6018
ipq8074
mdm9615
msm8916
@@ -41,6 +42,7 @@ description: |
The 'board' element must be one of the following strings:
cdp
+ cp01-c1
dragonboard
hk01
idp
@@ -150,4 +152,10 @@ properties:
- enum:
- qcom,sc7180-idp
- const: qcom,sc7180
+
+ - items:
+ - enum:
+ - qcom,ipq6018-cp01-c1
+ - const: qcom,ipq6018
+
...
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH V5 3/5] dt-bindings: qcom: Add ipq6018 bindings
@ 2020-01-16 7:44 ` Sricharan R
0 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
Cc: Selvam Sathappan Periakaruppan
Document the new ipq6018 SOC/board device tree bindings.
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 529d924..164177e 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -28,6 +28,7 @@ description: |
apq8074
apq8084
apq8096
+ ipq6018
ipq8074
mdm9615
msm8916
@@ -41,6 +42,7 @@ description: |
The 'board' element must be one of the following strings:
cdp
+ cp01-c1
dragonboard
hk01
idp
@@ -150,4 +152,10 @@ properties:
- enum:
- qcom,sc7180-idp
- const: qcom,sc7180
+
+ - items:
+ - enum:
+ - qcom,ipq6018-cp01-c1
+ - const: qcom,ipq6018
+
...
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH V5 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support
2020-01-16 7:44 ` Sricharan R
@ 2020-01-16 7:45 ` Sricharan R
-1 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:45 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
Cc: Abhishek Sahu
Add initial device tree support for the Qualcomm IPQ6018 SoC and
CP01 evaluation board.
Co-developed-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
[v5] *Added fixed clocks in gcc clock controller
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 30 ++++
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 217 +++++++++++++++++++++++++++
3 files changed, 248 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 973c0f0..204775f 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -2,6 +2,7 @@
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
+dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb
diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
new file mode 100644
index 0000000..897b4b2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ6018 CP01 board device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq6018.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. IPQ6018/AP-CP01-C1";
+ compatible = "qcom,ipq6018-cp01", "qcom,ipq6018";
+
+ aliases {
+ serial0 = &blsp1_uart3;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " swiotlb=1";
+ };
+};
+
+&blsp1_uart3 {
+ pinctrl-0 = <&serial_3_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+};
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
new file mode 100644
index 0000000..0fb44e5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ6018 SoC device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-ipq6018.h>
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&intc>;
+
+ clocks {
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32000>;
+ #clock-cells = <0>;
+ };
+
+ xo: xo {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ cpus: cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x3>;
+ next-level-cache = <&L2_0>;
+ };
+
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <0x2>;
+ };
+ };
+
+ pmuv8: pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ psci: psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ tz: tz@48500000 {
+ reg = <0x0 0x48500000 0x0 0x00200000>;
+ no-map;
+ };
+ };
+
+ soc: soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+ dma-ranges;
+ compatible = "simple-bus";
+
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,ipq6018-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 80>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ serial_3_pins: serial3-pinmux {
+ pins = "gpio44", "gpio45";
+ function = "blsp2_uart";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
+
+ gcc: gcc@1800000 {
+ compatible = "qcom,gcc-ipq6018";
+ reg = <0x01800000 0x80000>;
+ clocks = <&xo>, <&sleep_clk>;
+ clock-names = "xo", "sleep_clk";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ blsp1_uart3: serial@78b1000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b1000 0x200>;
+ interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ intc: interrupt-controller@b000000 {
+ compatible = "qcom,msm-qgic2";
+ interrupt-controller;
+ #interrupt-cells = <0x3>;
+ reg = <0x0b000000 0x1000>, /*GICD*/
+ <0x0b002000 0x1000>, /*GICC*/
+ <0x0b001000 0x1000>, /*GICH*/
+ <0x0b004000 0x1000>; /*GICV*/
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ timer@b120000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0b120000 0x1000>;
+ clock-frequency = <19200000>;
+
+ frame@b120000 {
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b121000 0x1000>,
+ <0x0b122000 0x1000>;
+ };
+
+ frame@b123000 {
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0xb123000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b124000 {
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b124000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b125000 {
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b125000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b126000 {
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b126000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b127000 {
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b127000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b128000 {
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b128000 0x1000>;
+ status = "disabled";
+ };
+ };
+
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH V5 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support
@ 2020-01-16 7:45 ` Sricharan R
0 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:45 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
Cc: Abhishek Sahu
Add initial device tree support for the Qualcomm IPQ6018 SoC and
CP01 evaluation board.
Co-developed-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
[v5] *Added fixed clocks in gcc clock controller
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 30 ++++
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 217 +++++++++++++++++++++++++++
3 files changed, 248 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 973c0f0..204775f 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -2,6 +2,7 @@
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
+dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb
diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
new file mode 100644
index 0000000..897b4b2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ6018 CP01 board device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq6018.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. IPQ6018/AP-CP01-C1";
+ compatible = "qcom,ipq6018-cp01", "qcom,ipq6018";
+
+ aliases {
+ serial0 = &blsp1_uart3;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " swiotlb=1";
+ };
+};
+
+&blsp1_uart3 {
+ pinctrl-0 = <&serial_3_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+};
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
new file mode 100644
index 0000000..0fb44e5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ6018 SoC device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-ipq6018.h>
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&intc>;
+
+ clocks {
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32000>;
+ #clock-cells = <0>;
+ };
+
+ xo: xo {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ cpus: cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x3>;
+ next-level-cache = <&L2_0>;
+ };
+
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <0x2>;
+ };
+ };
+
+ pmuv8: pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ psci: psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ tz: tz@48500000 {
+ reg = <0x0 0x48500000 0x0 0x00200000>;
+ no-map;
+ };
+ };
+
+ soc: soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+ dma-ranges;
+ compatible = "simple-bus";
+
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,ipq6018-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 80>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ serial_3_pins: serial3-pinmux {
+ pins = "gpio44", "gpio45";
+ function = "blsp2_uart";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
+
+ gcc: gcc@1800000 {
+ compatible = "qcom,gcc-ipq6018";
+ reg = <0x01800000 0x80000>;
+ clocks = <&xo>, <&sleep_clk>;
+ clock-names = "xo", "sleep_clk";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ blsp1_uart3: serial@78b1000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b1000 0x200>;
+ interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ intc: interrupt-controller@b000000 {
+ compatible = "qcom,msm-qgic2";
+ interrupt-controller;
+ #interrupt-cells = <0x3>;
+ reg = <0x0b000000 0x1000>, /*GICD*/
+ <0x0b002000 0x1000>, /*GICC*/
+ <0x0b001000 0x1000>, /*GICH*/
+ <0x0b004000 0x1000>; /*GICV*/
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ timer@b120000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0b120000 0x1000>;
+ clock-frequency = <19200000>;
+
+ frame@b120000 {
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b121000 0x1000>,
+ <0x0b122000 0x1000>;
+ };
+
+ frame@b123000 {
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0xb123000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b124000 {
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b124000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b125000 {
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b125000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b126000 {
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b126000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b127000 {
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b127000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b128000 {
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b128000 0x1000>;
+ status = "disabled";
+ };
+ };
+
+ };
+};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH V5 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl
2020-01-16 7:44 ` Sricharan R
@ 2020-01-16 7:45 ` Sricharan R
-1 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:45 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
These configs are required for booting kernel in qcom
ipq6018 boards.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
arch/arm64/configs/defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 43fa238..16aecea 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -405,6 +405,7 @@ CONFIG_PINCTRL_IMX8MN=y
CONFIG_PINCTRL_IMX8MQ=y
CONFIG_PINCTRL_IMX8QXP=y
CONFIG_PINCTRL_IPQ8074=y
+CONFIG_PINCTRL_IPQ6018=y
CONFIG_PINCTRL_MSM8916=y
CONFIG_PINCTRL_MSM8994=y
CONFIG_PINCTRL_MSM8996=y
@@ -718,6 +719,7 @@ CONFIG_QCOM_CLK_APCS_MSM8916=y
CONFIG_QCOM_CLK_SMD_RPM=y
CONFIG_QCOM_CLK_RPMH=y
CONFIG_IPQ_GCC_8074=y
+CONFIG_IPQ_GCC_6018=y
CONFIG_MSM_GCC_8916=y
CONFIG_MSM_GCC_8994=y
CONFIG_MSM_MMCC_8996=y
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH V5 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl
@ 2020-01-16 7:45 ` Sricharan R
0 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-16 7:45 UTC (permalink / raw)
To: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt,
sivaprak, sricharan
These configs are required for booting kernel in qcom
ipq6018 boards.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
arch/arm64/configs/defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 43fa238..16aecea 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -405,6 +405,7 @@ CONFIG_PINCTRL_IMX8MN=y
CONFIG_PINCTRL_IMX8MQ=y
CONFIG_PINCTRL_IMX8QXP=y
CONFIG_PINCTRL_IPQ8074=y
+CONFIG_PINCTRL_IPQ6018=y
CONFIG_PINCTRL_MSM8916=y
CONFIG_PINCTRL_MSM8994=y
CONFIG_PINCTRL_MSM8996=y
@@ -718,6 +719,7 @@ CONFIG_QCOM_CLK_APCS_MSM8916=y
CONFIG_QCOM_CLK_SMD_RPM=y
CONFIG_QCOM_CLK_RPMH=y
CONFIG_IPQ_GCC_8074=y
+CONFIG_IPQ_GCC_6018=y
CONFIG_MSM_GCC_8916=y
CONFIG_MSM_GCC_8994=y
CONFIG_MSM_MMCC_8996=y
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread
* Re: [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
2020-01-16 7:44 ` Sricharan R
@ 2020-01-17 16:01 ` Rob Herring
-1 siblings, 0 replies; 16+ messages in thread
From: Rob Herring @ 2020-01-17 16:01 UTC (permalink / raw)
To: Sricharan R
Cc: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, sivaprak,
Rajkumar Ayyasamy, Selvam Sathappan Periakaruppan
On Thu, Jan 16, 2020 at 01:14:57PM +0530, Sricharan R wrote:
> Add device tree binding Documentation details for ipq6018
> pinctrl driver.
>
> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
> ---
> [V5]
> * Addressed review comments from Rob
> * Ran dt bindings check and no errors were reported
> .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 162 +++++++++++++++++++++
> 1 file changed, 162 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> new file mode 100644
> index 0000000..0622258
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> @@ -0,0 +1,162 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
> +
> +maintainers:
> + - Sricharan R <sricharan@codeaurora.org>
> +
> +description: |
> + This binding describes the Top Level Mode Multiplexer block found in the
> + IPQ6018 platform.
> +
> +properties:
> + compatible:
> + const: qcom,ipq6018-pinctrl
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + description: Specifies the TLMM summary IRQ
> + maxItems: 1
> +
> + interrupt-controller: true
> +
> + '#interrupt-cells':
> + description:
> + Specifies the PIN numbers and Flags, as defined in defined in
> + include/dt-bindings/interrupt-controller/irq.h
> + const: 2
> +
> + gpio-controller: true
> +
> + '#gpio-cells':
> + description: Specifying the pin number and flags, as defined in
> + include/dt-bindings/gpio/gpio.h
> + const: 2
> +
> + gpio-ranges:
> + description: Documentation/devicetree/bindings/gpio/gpio.txt
You can drop the description. Nothing here specific to this binding.
> + maxItems: 1
> +
> +#PIN CONFIGURATION NODES
> +patternProperties:
> + '.*-pin.*':
Ideally, this would be a bit more constrained. Such as '-pin$' or
'-pinmux$'.
Note that '-pin' is equivalent to what you have.
> + type: object
> + description:
> + Pinctrl node's client devices use subnodes for desired pin configuration.
> + Client device subnodes use below standard properties.
> + allOf:
> + - $ref: "/schemas/pinctrl/pincfg-node.yaml"
> +
> + properties:
> + pins:
> + description:
> + List of gpio pins affected by the properties specified in this
> + subnode. The valid values are gpio1-80, sdc1_clk, sdc1_cmd,
> + sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_cmd, qdsd_data0,
> + qdsd_data1, qdsd_data2, qdsd_data3
Looks like constraints:
items:
oneOf:
- pattern: "^gpio([1-9]|[1-7][0-9]|80)$"
- enum: [ sdc1_clk, sdc1_cmd, ... ]
> + minItems: 1
> + maxItems: 4
> +
> + function:
> + description:
> + Specify the alternative function to be configured for the specified
> + pins.
> + enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
> + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
> + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
> + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c,
> + blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi,
> + blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi,
> + blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi,
> + blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi,
> + blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst,
> + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
> + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
> + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
> + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
> + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
> + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
> + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
> + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
> + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
> + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
> + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
> + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
> + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
> + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
> + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
> + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
> + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
> +
> + drive-strength:
> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
> + default: 2
> + description:
> + Selects the drive strength for the specified pins, in mA.
> +
> + bias-pull-down:
> + type: boolean
> + description: The specified pin should be configured as pull down.
> +
> + bias-pull-up:
> + type: boolean
> + description: The specified pin should be configured as pull up.
> +
> + bias-disable:
> + type: boolean
> + description: The specified pin should be configured as no pull.
> +
> + output-high:
> + type: boolean
> + description: The specified pin is configured in output mode, driven
> + high.
> +
> + output-low:
> + type: boolean
> + description: The specified pin is configured in output mode, driven
> + low.
No need to redefine the type and description on these 5 properties. Just
a value of 'true' is enough.
> +
> + required:
> + - pins
> + - function
> +
> + additionalProperties: false
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> + - interrupt-controller
> + - '#interrupt-cells'
> + - gpio-controller
> + - '#gpio-cells'
> + - gpio-ranges
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + tlmm: pinctrl@1000000 {
> + compatible = "qcom,ipq6018-pinctrl";
> + reg = <0x01000000 0x300000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&tlmm 0 80>;
> +
> + serial3-pinmux {
> + pins = "gpio44", "gpio45";
> + function = "blsp2_uart";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> + };
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
@ 2020-01-17 16:01 ` Rob Herring
0 siblings, 0 replies; 16+ messages in thread
From: Rob Herring @ 2020-01-17 16:01 UTC (permalink / raw)
To: Sricharan R
Cc: devicetree, Rajkumar Ayyasamy, linux-arm-msm, linus.walleij,
linux-kernel, Selvam Sathappan Periakaruppan, linux-gpio, agross,
sivaprak, linux-soc, linux-arm-kernel
On Thu, Jan 16, 2020 at 01:14:57PM +0530, Sricharan R wrote:
> Add device tree binding Documentation details for ipq6018
> pinctrl driver.
>
> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
> ---
> [V5]
> * Addressed review comments from Rob
> * Ran dt bindings check and no errors were reported
> .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 162 +++++++++++++++++++++
> 1 file changed, 162 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> new file mode 100644
> index 0000000..0622258
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> @@ -0,0 +1,162 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
> +
> +maintainers:
> + - Sricharan R <sricharan@codeaurora.org>
> +
> +description: |
> + This binding describes the Top Level Mode Multiplexer block found in the
> + IPQ6018 platform.
> +
> +properties:
> + compatible:
> + const: qcom,ipq6018-pinctrl
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + description: Specifies the TLMM summary IRQ
> + maxItems: 1
> +
> + interrupt-controller: true
> +
> + '#interrupt-cells':
> + description:
> + Specifies the PIN numbers and Flags, as defined in defined in
> + include/dt-bindings/interrupt-controller/irq.h
> + const: 2
> +
> + gpio-controller: true
> +
> + '#gpio-cells':
> + description: Specifying the pin number and flags, as defined in
> + include/dt-bindings/gpio/gpio.h
> + const: 2
> +
> + gpio-ranges:
> + description: Documentation/devicetree/bindings/gpio/gpio.txt
You can drop the description. Nothing here specific to this binding.
> + maxItems: 1
> +
> +#PIN CONFIGURATION NODES
> +patternProperties:
> + '.*-pin.*':
Ideally, this would be a bit more constrained. Such as '-pin$' or
'-pinmux$'.
Note that '-pin' is equivalent to what you have.
> + type: object
> + description:
> + Pinctrl node's client devices use subnodes for desired pin configuration.
> + Client device subnodes use below standard properties.
> + allOf:
> + - $ref: "/schemas/pinctrl/pincfg-node.yaml"
> +
> + properties:
> + pins:
> + description:
> + List of gpio pins affected by the properties specified in this
> + subnode. The valid values are gpio1-80, sdc1_clk, sdc1_cmd,
> + sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_cmd, qdsd_data0,
> + qdsd_data1, qdsd_data2, qdsd_data3
Looks like constraints:
items:
oneOf:
- pattern: "^gpio([1-9]|[1-7][0-9]|80)$"
- enum: [ sdc1_clk, sdc1_cmd, ... ]
> + minItems: 1
> + maxItems: 4
> +
> + function:
> + description:
> + Specify the alternative function to be configured for the specified
> + pins.
> + enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
> + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
> + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
> + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c,
> + blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi,
> + blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi,
> + blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi,
> + blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi,
> + blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst,
> + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
> + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
> + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
> + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
> + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
> + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
> + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
> + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
> + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
> + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
> + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
> + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
> + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
> + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
> + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
> + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
> + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
> +
> + drive-strength:
> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
> + default: 2
> + description:
> + Selects the drive strength for the specified pins, in mA.
> +
> + bias-pull-down:
> + type: boolean
> + description: The specified pin should be configured as pull down.
> +
> + bias-pull-up:
> + type: boolean
> + description: The specified pin should be configured as pull up.
> +
> + bias-disable:
> + type: boolean
> + description: The specified pin should be configured as no pull.
> +
> + output-high:
> + type: boolean
> + description: The specified pin is configured in output mode, driven
> + high.
> +
> + output-low:
> + type: boolean
> + description: The specified pin is configured in output mode, driven
> + low.
No need to redefine the type and description on these 5 properties. Just
a value of 'true' is enough.
> +
> + required:
> + - pins
> + - function
> +
> + additionalProperties: false
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> + - interrupt-controller
> + - '#interrupt-cells'
> + - gpio-controller
> + - '#gpio-cells'
> + - gpio-ranges
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + tlmm: pinctrl@1000000 {
> + compatible = "qcom,ipq6018-pinctrl";
> + reg = <0x01000000 0x300000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&tlmm 0 80>;
> +
> + serial3-pinmux {
> + pins = "gpio44", "gpio45";
> + function = "blsp2_uart";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> + };
> --
> 2.7.4
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
2020-01-17 16:01 ` Rob Herring
@ 2020-01-19 13:15 ` Sricharan R
-1 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-19 13:15 UTC (permalink / raw)
To: Rob Herring
Cc: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-gpio, linux-kernel, linux-soc, sivaprak,
Rajkumar Ayyasamy, Selvam Sathappan Periakaruppan
Hi Rob,
Thanks for the review.
On 1/17/2020 9:31 PM, Rob Herring wrote:
> On Thu, Jan 16, 2020 at 01:14:57PM +0530, Sricharan R wrote:
>> Add device tree binding Documentation details for ipq6018
>> pinctrl driver.
>>
>> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
>> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
>> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
>> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
>> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
>> ---
>> [V5]
>> * Addressed review comments from Rob
>> * Ran dt bindings check and no errors were reported
>> .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 162 +++++++++++++++++++++
>> 1 file changed, 162 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>> new file mode 100644
>> index 0000000..0622258
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>> @@ -0,0 +1,162 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
>> +
>> +maintainers:
>> + - Sricharan R <sricharan@codeaurora.org>
>> +
>> +description: |
>> + This binding describes the Top Level Mode Multiplexer block found in the
>> + IPQ6018 platform.
>> +
>> +properties:
>> + compatible:
>> + const: qcom,ipq6018-pinctrl
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + interrupts:
>> + description: Specifies the TLMM summary IRQ
>> + maxItems: 1
>> +
>> + interrupt-controller: true
>> +
>> + '#interrupt-cells':
>> + description:
>> + Specifies the PIN numbers and Flags, as defined in defined in
>> + include/dt-bindings/interrupt-controller/irq.h
>> + const: 2
>> +
>> + gpio-controller: true
>> +
>> + '#gpio-cells':
>> + description: Specifying the pin number and flags, as defined in
>> + include/dt-bindings/gpio/gpio.h
>> + const: 2
>> +
>> + gpio-ranges:
>> + description: Documentation/devicetree/bindings/gpio/gpio.txt
>
> You can drop the description. Nothing here specific to this binding.
>
ok.
>> + maxItems: 1
>> +
>> +#PIN CONFIGURATION NODES
>> +patternProperties:
>> + '.*-pin.*':
>
> Ideally, this would be a bit more constrained. Such as '-pin$' or
> '-pinmux$'.
>
> Note that '-pin' is equivalent to what you have.
>
ok.
>> + type: object
>> + description:
>> + Pinctrl node's client devices use subnodes for desired pin configuration.
>> + Client device subnodes use below standard properties.
>> + allOf:
>> + - $ref: "/schemas/pinctrl/pincfg-node.yaml"
>> +
>> + properties:
>> + pins:
>> + description:
>> + List of gpio pins affected by the properties specified in this
>> + subnode. The valid values are gpio1-80, sdc1_clk, sdc1_cmd,
>> + sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_cmd, qdsd_data0,
>> + qdsd_data1, qdsd_data2, qdsd_data3
>
> Looks like constraints:
>
> items:
> oneOf:
> - pattern: "^gpio([1-9]|[1-7][0-9]|80)$"
> - enum: [ sdc1_clk, sdc1_cmd, ... ]
>
ok.
>> + minItems: 1
>> + maxItems: 4
>> +
>> + function:
>> + description:
>> + Specify the alternative function to be configured for the specified
>> + pins.
>> + enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
>> + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
>> + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
>> + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c,
>> + blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi,
>> + blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi,
>> + blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi,
>> + blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi,
>> + blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst,
>> + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
>> + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
>> + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
>> + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
>> + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
>> + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
>> + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
>> + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
>> + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
>> + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
>> + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
>> + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
>> + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
>> + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
>> + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
>> + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
>> + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
>> +
>> + drive-strength:
>> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
>> + default: 2
>> + description:
>> + Selects the drive strength for the specified pins, in mA.
>
>> +
>> + bias-pull-down:
>> + type: boolean
>> + description: The specified pin should be configured as pull down.
>> +
>> + bias-pull-up:
>> + type: boolean
>> + description: The specified pin should be configured as pull up.
>> +
>> + bias-disable:
>> + type: boolean
>> + description: The specified pin should be configured as no pull.
>> +
>> + output-high:
>> + type: boolean
>> + description: The specified pin is configured in output mode, driven
>> + high.
>> +
>> + output-low:
>> + type: boolean
>> + description: The specified pin is configured in output mode, driven
>> + low.
>
> No need to redefine the type and description on these 5 properties. Just
> a value of 'true' is enough.
>
ok.
Regards,
Sricharan
--
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
@ 2020-01-19 13:15 ` Sricharan R
0 siblings, 0 replies; 16+ messages in thread
From: Sricharan R @ 2020-01-19 13:15 UTC (permalink / raw)
To: Rob Herring
Cc: devicetree, Rajkumar Ayyasamy, linux-arm-msm, linus.walleij,
linux-kernel, Selvam Sathappan Periakaruppan, linux-gpio, agross,
sivaprak, linux-soc, linux-arm-kernel
Hi Rob,
Thanks for the review.
On 1/17/2020 9:31 PM, Rob Herring wrote:
> On Thu, Jan 16, 2020 at 01:14:57PM +0530, Sricharan R wrote:
>> Add device tree binding Documentation details for ipq6018
>> pinctrl driver.
>>
>> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
>> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
>> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
>> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
>> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
>> ---
>> [V5]
>> * Addressed review comments from Rob
>> * Ran dt bindings check and no errors were reported
>> .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 162 +++++++++++++++++++++
>> 1 file changed, 162 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>> new file mode 100644
>> index 0000000..0622258
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>> @@ -0,0 +1,162 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
>> +
>> +maintainers:
>> + - Sricharan R <sricharan@codeaurora.org>
>> +
>> +description: |
>> + This binding describes the Top Level Mode Multiplexer block found in the
>> + IPQ6018 platform.
>> +
>> +properties:
>> + compatible:
>> + const: qcom,ipq6018-pinctrl
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + interrupts:
>> + description: Specifies the TLMM summary IRQ
>> + maxItems: 1
>> +
>> + interrupt-controller: true
>> +
>> + '#interrupt-cells':
>> + description:
>> + Specifies the PIN numbers and Flags, as defined in defined in
>> + include/dt-bindings/interrupt-controller/irq.h
>> + const: 2
>> +
>> + gpio-controller: true
>> +
>> + '#gpio-cells':
>> + description: Specifying the pin number and flags, as defined in
>> + include/dt-bindings/gpio/gpio.h
>> + const: 2
>> +
>> + gpio-ranges:
>> + description: Documentation/devicetree/bindings/gpio/gpio.txt
>
> You can drop the description. Nothing here specific to this binding.
>
ok.
>> + maxItems: 1
>> +
>> +#PIN CONFIGURATION NODES
>> +patternProperties:
>> + '.*-pin.*':
>
> Ideally, this would be a bit more constrained. Such as '-pin$' or
> '-pinmux$'.
>
> Note that '-pin' is equivalent to what you have.
>
ok.
>> + type: object
>> + description:
>> + Pinctrl node's client devices use subnodes for desired pin configuration.
>> + Client device subnodes use below standard properties.
>> + allOf:
>> + - $ref: "/schemas/pinctrl/pincfg-node.yaml"
>> +
>> + properties:
>> + pins:
>> + description:
>> + List of gpio pins affected by the properties specified in this
>> + subnode. The valid values are gpio1-80, sdc1_clk, sdc1_cmd,
>> + sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_cmd, qdsd_data0,
>> + qdsd_data1, qdsd_data2, qdsd_data3
>
> Looks like constraints:
>
> items:
> oneOf:
> - pattern: "^gpio([1-9]|[1-7][0-9]|80)$"
> - enum: [ sdc1_clk, sdc1_cmd, ... ]
>
ok.
>> + minItems: 1
>> + maxItems: 4
>> +
>> + function:
>> + description:
>> + Specify the alternative function to be configured for the specified
>> + pins.
>> + enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
>> + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
>> + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
>> + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c,
>> + blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi,
>> + blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi,
>> + blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi,
>> + blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi,
>> + blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst,
>> + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
>> + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
>> + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
>> + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
>> + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
>> + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
>> + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
>> + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
>> + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
>> + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
>> + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
>> + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
>> + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
>> + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
>> + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
>> + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
>> + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
>> +
>> + drive-strength:
>> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
>> + default: 2
>> + description:
>> + Selects the drive strength for the specified pins, in mA.
>
>> +
>> + bias-pull-down:
>> + type: boolean
>> + description: The specified pin should be configured as pull down.
>> +
>> + bias-pull-up:
>> + type: boolean
>> + description: The specified pin should be configured as pull up.
>> +
>> + bias-disable:
>> + type: boolean
>> + description: The specified pin should be configured as no pull.
>> +
>> + output-high:
>> + type: boolean
>> + description: The specified pin is configured in output mode, driven
>> + high.
>> +
>> + output-low:
>> + type: boolean
>> + description: The specified pin is configured in output mode, driven
>> + low.
>
> No need to redefine the type and description on these 5 properties. Just
> a value of 'true' is enough.
>
ok.
Regards,
Sricharan
--
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
end of thread, other threads:[~2020-01-19 13:16 UTC | newest]
Thread overview: 16+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-01-16 7:44 [PATCH V5 0/5] Add minimal boot support for IPQ6018 Sricharan R
2020-01-16 7:44 ` Sricharan R
2020-01-16 7:44 ` [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R
2020-01-16 7:44 ` Sricharan R
2020-01-17 16:01 ` Rob Herring
2020-01-17 16:01 ` Rob Herring
2020-01-19 13:15 ` Sricharan R
2020-01-19 13:15 ` Sricharan R
2020-01-16 7:44 ` [PATCH V5 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R
2020-01-16 7:44 ` Sricharan R
2020-01-16 7:44 ` [PATCH V5 3/5] dt-bindings: qcom: Add ipq6018 bindings Sricharan R
2020-01-16 7:44 ` Sricharan R
2020-01-16 7:45 ` [PATCH V5 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support Sricharan R
2020-01-16 7:45 ` Sricharan R
2020-01-16 7:45 ` [PATCH V5 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Sricharan R
2020-01-16 7:45 ` Sricharan R
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.