[PATCH AUTOSEL 5.4 001/107] batman-adv: Fix DAT candidate selection on little endian systems

[PATCH AUTOSEL 5.4 001/107] batman-adv: Fix DAT candidate selection on little endian systems

[Sasha Levin]

From: Sven Eckelmann <sven@narfation.org>

[ Upstream commit 4cc4a1708903f404d2ca0dfde30e71e052c6cbc9 ]

The distributed arp table is using a DHT to store and retrieve MAC address
information for an IP address. This is done using unicast messages to
selected peers. The potential peers are looked up using the IP address and
the VID.

While the IP address is always stored in big endian byte order, this is not
the case of the VID. It can (depending on the host system) either be big
endian or little endian. The host must therefore always convert it to big
endian to ensure that all devices calculate the same peers for the same
lookup data.

Fixes: be1db4f6615b ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/batman-adv/distributed-arp-table.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/net/batman-adv/distributed-arp-table.c b/net/batman-adv/distributed-arp-table.c
index b0af3a11d4069..ec7bf5a4a9fc7 100644
--- a/net/batman-adv/distributed-arp-table.c
+++ b/net/batman-adv/distributed-arp-table.c
@@ -285,6 +285,7 @@ static u32 batadv_hash_dat(const void *data, u32 size)
 	u32 hash = 0;
 	const struct batadv_dat_entry *dat = data;
 	const unsigned char *key;
+	__be16 vid;
 	u32 i;
 
 	key = (const unsigned char *)&dat->ip;
@@ -294,7 +295,8 @@ static u32 batadv_hash_dat(const void *data, u32 size)
 		hash ^= (hash >> 6);
 	}
 
-	key = (const unsigned char *)&dat->vid;
+	vid = htons(dat->vid);
+	key = (__force const unsigned char *)&vid;
 	for (i = 0; i < sizeof(dat->vid); i++) {
 		hash += key[i];
 		hash += (hash << 10);
-- 
2.20.1

[PATCH AUTOSEL 5.4 002/107] clk: sunxi-ng: v3s: Fix incorrect number of hw_clks.

[Sasha Levin]

From: Yunhao Tian <18373444@buaa.edu.cn>

[ Upstream commit 4ff40d140e2a2060ef6051800a4a9eab07624f42 ]

The hws field of sun8i_v3s_hw_clks has only 74
members. However, the number specified by CLK_NUMBER
is 77 (= CLK_I2S0 + 1). This leads to runtime segmentation
fault that is not always reproducible.

This patch fixes the problem by specifying correct clock number.

Signed-off-by: Yunhao Tian <18373444@buaa.edu.cn>
[Maxime: Also remove the CLK_NUMBER definition]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/sunxi-ng/ccu-sun8i-v3s.c | 4 ++--
 drivers/clk/sunxi-ng/ccu-sun8i-v3s.h | 2 --
 2 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
index 5c779eec454b6..0e36ca3bf3d52 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
@@ -618,7 +618,7 @@ static struct clk_hw_onecell_data sun8i_v3s_hw_clks = {
 		[CLK_MBUS]		= &mbus_clk.common.hw,
 		[CLK_MIPI_CSI]		= &mipi_csi_clk.common.hw,
 	},
-	.num	= CLK_NUMBER,
+	.num	= CLK_PLL_DDR1 + 1,
 };
 
 static struct clk_hw_onecell_data sun8i_v3_hw_clks = {
@@ -700,7 +700,7 @@ static struct clk_hw_onecell_data sun8i_v3_hw_clks = {
 		[CLK_MBUS]		= &mbus_clk.common.hw,
 		[CLK_MIPI_CSI]		= &mipi_csi_clk.common.hw,
 	},
-	.num	= CLK_NUMBER,
+	.num	= CLK_I2S0 + 1,
 };
 
 static struct ccu_reset_map sun8i_v3s_ccu_resets[] = {
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.h b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.h
index b0160d305a677..108eeeedcbf76 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.h
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.h
@@ -51,6 +51,4 @@
 
 #define CLK_PLL_DDR1		74
 
-#define CLK_NUMBER		(CLK_I2S0 + 1)
-
 #endif /* _CCU_SUN8I_H3_H_ */
-- 
2.20.1

[PATCH AUTOSEL 5.4 002/107] clk: sunxi-ng: v3s: Fix incorrect number of hw_clks.

[Sasha Levin]

From: Yunhao Tian <18373444@buaa.edu.cn>

[ Upstream commit 4ff40d140e2a2060ef6051800a4a9eab07624f42 ]

The hws field of sun8i_v3s_hw_clks has only 74
members. However, the number specified by CLK_NUMBER
is 77 (= CLK_I2S0 + 1). This leads to runtime segmentation
fault that is not always reproducible.

This patch fixes the problem by specifying correct clock number.

Signed-off-by: Yunhao Tian <18373444@buaa.edu.cn>
[Maxime: Also remove the CLK_NUMBER definition]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/sunxi-ng/ccu-sun8i-v3s.c | 4 ++--
 drivers/clk/sunxi-ng/ccu-sun8i-v3s.h | 2 --
 2 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
index 5c779eec454b6..0e36ca3bf3d52 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
@@ -618,7 +618,7 @@ static struct clk_hw_onecell_data sun8i_v3s_hw_clks = {
 		[CLK_MBUS]		= &mbus_clk.common.hw,
 		[CLK_MIPI_CSI]		= &mipi_csi_clk.common.hw,
 	},
-	.num	= CLK_NUMBER,
+	.num	= CLK_PLL_DDR1 + 1,
 };
 
 static struct clk_hw_onecell_data sun8i_v3_hw_clks = {
@@ -700,7 +700,7 @@ static struct clk_hw_onecell_data sun8i_v3_hw_clks = {
 		[CLK_MBUS]		= &mbus_clk.common.hw,
 		[CLK_MIPI_CSI]		= &mipi_csi_clk.common.hw,
 	},
-	.num	= CLK_NUMBER,
+	.num	= CLK_I2S0 + 1,
 };
 
 static struct ccu_reset_map sun8i_v3s_ccu_resets[] = {
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.h b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.h
index b0160d305a677..108eeeedcbf76 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.h
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.h
@@ -51,6 +51,4 @@
 
 #define CLK_PLL_DDR1		74
 
-#define CLK_NUMBER		(CLK_I2S0 + 1)
-
 #endif /* _CCU_SUN8I_H3_H_ */
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 003/107] ARM: dts: meson8: fix the size of the PMU registers

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit 46c9585ed4af688ff1be6d4e76d7ed2f04de4fba ]

The PMU registers are at least 0x18 bytes wide. Meson8b already uses a
size of 0x18. The structure of the PMU registers on Meson8 and Meson8b
is similar but not identical.

Meson8 and Meson8b have the following registers in common (starting at
AOBUS + 0xe0):
  #define AO_RTI_PWR_A9_CNTL0 0xe0 (0x38 << 2)
  #define AO_RTI_PWR_A9_CNTL1 0xe4 (0x39 << 2)
  #define AO_RTI_GEN_PWR_SLEEP0 0xe8 (0x3a << 2)
  #define AO_RTI_GEN_PWR_ISO0 0x4c (0x3b << 2)

Meson8b additionally has these three registers:
  #define AO_RTI_GEN_PWR_ACK0 0xf0 (0x3c << 2)
  #define AO_RTI_PWR_A9_MEM_PD0 0xf4 (0x3d << 2)
  #define AO_RTI_PWR_A9_MEM_PD1 0xf8 (0x3e << 2)

Thus we can assume that the register size of the PMU IP blocks is
identical on both SoCs (and Meson8 just contains some reserved registers
in that area) because the CEC registers start right after the PMU
(AO_RTI_*) registers at AOBUS + 0x100 (0x40 << 2).

The upcoming power domain driver will need to read and write the
AO_RTI_GEN_PWR_SLEEP0 and AO_RTI_GEN_PWR_ISO0 registers, so the updated
size is needed for that driver to work.

Fixes: 4a5a27116b447d ("ARM: dts: meson8: add support for booting the secondary CPU cores")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/meson8.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
index 5a7e3e5caebe2..3c534cd50ee3b 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/meson8.dtsi
@@ -253,7 +253,7 @@
 &aobus {
 	pmu: pmu@e0 {
 		compatible = "amlogic,meson8-pmu", "syscon";
-		reg = <0xe0 0x8>;
+		reg = <0xe0 0x18>;
 	};
 
 	pinctrl_aobus: pinctrl@84 {
-- 
2.20.1

[PATCH AUTOSEL 5.4 003/107] ARM: dts: meson8: fix the size of the PMU registers

[Sasha Levin]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit 46c9585ed4af688ff1be6d4e76d7ed2f04de4fba ]

The PMU registers are at least 0x18 bytes wide. Meson8b already uses a
size of 0x18. The structure of the PMU registers on Meson8 and Meson8b
is similar but not identical.

Meson8 and Meson8b have the following registers in common (starting at
AOBUS + 0xe0):
  #define AO_RTI_PWR_A9_CNTL0 0xe0 (0x38 << 2)
  #define AO_RTI_PWR_A9_CNTL1 0xe4 (0x39 << 2)
  #define AO_RTI_GEN_PWR_SLEEP0 0xe8 (0x3a << 2)
  #define AO_RTI_GEN_PWR_ISO0 0x4c (0x3b << 2)

Meson8b additionally has these three registers:
  #define AO_RTI_GEN_PWR_ACK0 0xf0 (0x3c << 2)
  #define AO_RTI_PWR_A9_MEM_PD0 0xf4 (0x3d << 2)
  #define AO_RTI_PWR_A9_MEM_PD1 0xf8 (0x3e << 2)

Thus we can assume that the register size of the PMU IP blocks is
identical on both SoCs (and Meson8 just contains some reserved registers
in that area) because the CEC registers start right after the PMU
(AO_RTI_*) registers at AOBUS + 0x100 (0x40 << 2).

The upcoming power domain driver will need to read and write the
AO_RTI_GEN_PWR_SLEEP0 and AO_RTI_GEN_PWR_ISO0 registers, so the updated
size is needed for that driver to work.

Fixes: 4a5a27116b447d ("ARM: dts: meson8: add support for booting the secondary CPU cores")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/meson8.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
index 5a7e3e5caebe2..3c534cd50ee3b 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/meson8.dtsi
@@ -253,7 +253,7 @@
 &aobus {
 	pmu: pmu@e0 {
 		compatible = "amlogic,meson8-pmu", "syscon";
-		reg = <0xe0 0x8>;
+		reg = <0xe0 0x18>;
 	};
 
 	pinctrl_aobus: pinctrl@84 {
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 004/107] dt-bindings: reset: meson8b: fix duplicate reset IDs

[Sasha Levin]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit 4881873f4cc1460f63d85fa81363d56be328ccdc ]

According to the public S805 datasheet the RESET2 register uses the
following bits for the PIC_DC, PSC and NAND reset lines:
- PIC_DC is at bit 3 (meaning: RESET_VD_RMEM + 3)
- PSC is at bit 4 (meaning: RESET_VD_RMEM + 4)
- NAND is at bit 5 (meaning: RESET_VD_RMEM + 4)

Update the reset IDs of these three reset lines so they don't conflict
with PIC_DC and map to the actual hardware reset lines.

Fixes: 79795e20a184eb ("dt-bindings: reset: Add bindings for the Meson SoC Reset Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/dt-bindings/reset/amlogic,meson8b-reset.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/include/dt-bindings/reset/amlogic,meson8b-reset.h b/include/dt-bindings/reset/amlogic,meson8b-reset.h
index c614438bcbdb8..fbc524a900da1 100644
--- a/include/dt-bindings/reset/amlogic,meson8b-reset.h
+++ b/include/dt-bindings/reset/amlogic,meson8b-reset.h
@@ -46,9 +46,9 @@
 #define RESET_VD_RMEM			64
 #define RESET_AUDIN			65
 #define RESET_DBLK			66
-#define RESET_PIC_DC			66
-#define RESET_PSC			66
-#define RESET_NAND			66
+#define RESET_PIC_DC			67
+#define RESET_PSC			68
+#define RESET_NAND			69
 #define RESET_GE2D			70
 #define RESET_PARSER_REG		71
 #define RESET_PARSER_FETCH		72
-- 
2.20.1

[PATCH AUTOSEL 5.4 004/107] dt-bindings: reset: meson8b: fix duplicate reset IDs

[Sasha Levin]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit 4881873f4cc1460f63d85fa81363d56be328ccdc ]

According to the public S805 datasheet the RESET2 register uses the
following bits for the PIC_DC, PSC and NAND reset lines:
- PIC_DC is at bit 3 (meaning: RESET_VD_RMEM + 3)
- PSC is at bit 4 (meaning: RESET_VD_RMEM + 4)
- NAND is at bit 5 (meaning: RESET_VD_RMEM + 4)

Update the reset IDs of these three reset lines so they don't conflict
with PIC_DC and map to the actual hardware reset lines.

Fixes: 79795e20a184eb ("dt-bindings: reset: Add bindings for the Meson SoC Reset Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/dt-bindings/reset/amlogic,meson8b-reset.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/include/dt-bindings/reset/amlogic,meson8b-reset.h b/include/dt-bindings/reset/amlogic,meson8b-reset.h
index c614438bcbdb8..fbc524a900da1 100644
--- a/include/dt-bindings/reset/amlogic,meson8b-reset.h
+++ b/include/dt-bindings/reset/amlogic,meson8b-reset.h
@@ -46,9 +46,9 @@
 #define RESET_VD_RMEM			64
 #define RESET_AUDIN			65
 #define RESET_DBLK			66
-#define RESET_PIC_DC			66
-#define RESET_PSC			66
-#define RESET_NAND			66
+#define RESET_PIC_DC			67
+#define RESET_PSC			68
+#define RESET_NAND			69
 #define RESET_GE2D			70
 #define RESET_PARSER_REG		71
 #define RESET_PARSER_FETCH		72
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 005/107] arm64: dts: meson-sm1-sei610: add gpio bluetooth interrupt

[Sasha Levin]

From: Guillaume La Roque <glaroque@baylibre.com>

[ Upstream commit 30388cc075720aa0af4f2cb5933afa1f8f39d313 ]

add gpio irq to support interrupt trigger mode.

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
index 3435aaa4e8db5..5d6a8dafe8dc0 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
@@ -361,6 +361,8 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
+		interrupt-parent = <&gpio_intc>;
+		interrupts = <95 IRQ_TYPE_LEVEL_HIGH>;
 		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
 		max-speed = <2000000>;
 		clocks = <&wifi32k>;
-- 
2.20.1

[PATCH AUTOSEL 5.4 005/107] arm64: dts: meson-sm1-sei610: add gpio bluetooth interrupt

[Sasha Levin]

From: Guillaume La Roque <glaroque@baylibre.com>

[ Upstream commit 30388cc075720aa0af4f2cb5933afa1f8f39d313 ]

add gpio irq to support interrupt trigger mode.

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
index 3435aaa4e8db5..5d6a8dafe8dc0 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
@@ -361,6 +361,8 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
+		interrupt-parent = <&gpio_intc>;
+		interrupts = <95 IRQ_TYPE_LEVEL_HIGH>;
 		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
 		max-speed = <2000000>;
 		clocks = <&wifi32k>;
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 006/107] ARM: OMAP2+: Fix ti_sysc_find_one_clockdomain to check for to_clk_hw_omap

[Sasha Levin]

From: Tony Lindgren <tony@atomide.com>

[ Upstream commit 90bdfa0b05e3cc809a7c1aa3b1f162b46ea1b330 ]

We must bail out early if the clock is not hw_omap. Otherwise we will
try to access invalid address with hwclk->clkdm_name:

Unable to handle kernel paging request at virtual address ffffffff
Internal error: Oops: 27 [#1] ARM
...
(strcmp) from [<c011b348>] (clkdm_lookup+0x40/0x60)
[<c011b348>] (clkdm_lookup) from [<c011cb84>] (ti_sysc_clkdm_init+0x5c/0x64)
[<c011cb84>] (ti_sysc_clkdm_init) from [<c03680a8>] (sysc_probe+0x948/0x117c)
[<c03680a8>] (sysc_probe) from [<c03d0af4>] (platform_drv_probe+0x48/0x98)
...

Fixes: 2b2f7def058a ("bus: ti-sysc: Add support for missing clockdomain handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/mach-omap2/pdata-quirks.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 1b7cf81ff0356..33688e1d9acf9 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -368,10 +368,14 @@ static void __init dra7x_evm_mmc_quirk(void)
 
 static struct clockdomain *ti_sysc_find_one_clockdomain(struct clk *clk)
 {
+	struct clk_hw *hw = __clk_get_hw(clk);
 	struct clockdomain *clkdm = NULL;
 	struct clk_hw_omap *hwclk;
 
-	hwclk = to_clk_hw_omap(__clk_get_hw(clk));
+	hwclk = to_clk_hw_omap(hw);
+	if (!omap2_clk_is_hw_omap(hw))
+		return NULL;
+
 	if (hwclk && hwclk->clkdm_name)
 		clkdm = clkdm_lookup(hwclk->clkdm_name);
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 006/107] ARM: OMAP2+: Fix ti_sysc_find_one_clockdomain to check for to_clk_hw_omap

[Sasha Levin]

From: Tony Lindgren <tony@atomide.com>

[ Upstream commit 90bdfa0b05e3cc809a7c1aa3b1f162b46ea1b330 ]

We must bail out early if the clock is not hw_omap. Otherwise we will
try to access invalid address with hwclk->clkdm_name:

Unable to handle kernel paging request at virtual address ffffffff
Internal error: Oops: 27 [#1] ARM
...
(strcmp) from [<c011b348>] (clkdm_lookup+0x40/0x60)
[<c011b348>] (clkdm_lookup) from [<c011cb84>] (ti_sysc_clkdm_init+0x5c/0x64)
[<c011cb84>] (ti_sysc_clkdm_init) from [<c03680a8>] (sysc_probe+0x948/0x117c)
[<c03680a8>] (sysc_probe) from [<c03d0af4>] (platform_drv_probe+0x48/0x98)
...

Fixes: 2b2f7def058a ("bus: ti-sysc: Add support for missing clockdomain handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/mach-omap2/pdata-quirks.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 1b7cf81ff0356..33688e1d9acf9 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -368,10 +368,14 @@ static void __init dra7x_evm_mmc_quirk(void)
 
 static struct clockdomain *ti_sysc_find_one_clockdomain(struct clk *clk)
 {
+	struct clk_hw *hw = __clk_get_hw(clk);
 	struct clockdomain *clkdm = NULL;
 	struct clk_hw_omap *hwclk;
 
-	hwclk = to_clk_hw_omap(__clk_get_hw(clk));
+	hwclk = to_clk_hw_omap(hw);
+	if (!omap2_clk_is_hw_omap(hw))
+		return NULL;
+
 	if (hwclk && hwclk->clkdm_name)
 		clkdm = clkdm_lookup(hwclk->clkdm_name);
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 006/107] ARM: OMAP2+: Fix ti_sysc_find_one_clockdomain to check for to_clk_hw_omap

[Sasha Levin]

From: Tony Lindgren <tony@atomide.com>

[ Upstream commit 90bdfa0b05e3cc809a7c1aa3b1f162b46ea1b330 ]

We must bail out early if the clock is not hw_omap. Otherwise we will
try to access invalid address with hwclk->clkdm_name:

Unable to handle kernel paging request at virtual address ffffffff
Internal error: Oops: 27 [#1] ARM
...
(strcmp) from [<c011b348>] (clkdm_lookup+0x40/0x60)
[<c011b348>] (clkdm_lookup) from [<c011cb84>] (ti_sysc_clkdm_init+0x5c/0x64)
[<c011cb84>] (ti_sysc_clkdm_init) from [<c03680a8>] (sysc_probe+0x948/0x117c)
[<c03680a8>] (sysc_probe) from [<c03d0af4>] (platform_drv_probe+0x48/0x98)
...

Fixes: 2b2f7def058a ("bus: ti-sysc: Add support for missing clockdomain handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/mach-omap2/pdata-quirks.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 1b7cf81ff0356..33688e1d9acf9 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -368,10 +368,14 @@ static void __init dra7x_evm_mmc_quirk(void)
 
 static struct clockdomain *ti_sysc_find_one_clockdomain(struct clk *clk)
 {
+	struct clk_hw *hw = __clk_get_hw(clk);
 	struct clockdomain *clkdm = NULL;
 	struct clk_hw_omap *hwclk;
 
-	hwclk = to_clk_hw_omap(__clk_get_hw(clk));
+	hwclk = to_clk_hw_omap(hw);
+	if (!omap2_clk_is_hw_omap(hw))
+		return NULL;
+
 	if (hwclk && hwclk->clkdm_name)
 		clkdm = clkdm_lookup(hwclk->clkdm_name);
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 007/107] bus: ti-sysc: Fix iterating over clocks

[Sasha Levin]

From: Tony Lindgren <tony@atomide.com>

[ Upstream commit 2c81f0f6d3f52ac222a5dc07a6e5c06e1543e88b ]

Commit d878970f6ce1 ("bus: ti-sysc: Add separate functions for handling
clocks") separated handling of optional clocks from the main clocks, but
introduced an issue where we do not necessarily allocate a slot for both
fck and ick clocks, but still assume fixed slots for enumerating over the
clocks.

Let's fix the issue by ensuring we always have slots for both fck and ick
even if we don't use ick, and don't attempt to enumerate optional clocks
if not allocated.

In the long run we might want to simplify things a bit by only allocating
space only for the optional clocks as we have only few devices with
optional clocks.

Fixes: d878970f6ce1 ("bus: ti-sysc: Add separate functions for handling clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/bus/ti-sysc.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c
index 34bd9bf4e68ab..abbf281ee337b 100644
--- a/drivers/bus/ti-sysc.c
+++ b/drivers/bus/ti-sysc.c
@@ -343,6 +343,12 @@ static int sysc_get_clocks(struct sysc *ddata)
 		return -EINVAL;
 	}
 
+	/* Always add a slot for main clocks fck and ick even if unused */
+	if (!nr_fck)
+		ddata->nr_clocks++;
+	if (!nr_ick)
+		ddata->nr_clocks++;
+
 	ddata->clocks = devm_kcalloc(ddata->dev,
 				     ddata->nr_clocks, sizeof(*ddata->clocks),
 				     GFP_KERNEL);
@@ -421,7 +427,7 @@ static int sysc_enable_opt_clocks(struct sysc *ddata)
 	struct clk *clock;
 	int i, error;
 
-	if (!ddata->clocks)
+	if (!ddata->clocks || ddata->nr_clocks < SYSC_OPTFCK0 + 1)
 		return 0;
 
 	for (i = SYSC_OPTFCK0; i < SYSC_MAX_CLOCKS; i++) {
@@ -455,7 +461,7 @@ static void sysc_disable_opt_clocks(struct sysc *ddata)
 	struct clk *clock;
 	int i;
 
-	if (!ddata->clocks)
+	if (!ddata->clocks || ddata->nr_clocks < SYSC_OPTFCK0 + 1)
 		return;
 
 	for (i = SYSC_OPTFCK0; i < SYSC_MAX_CLOCKS; i++) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 008/107] ARM: dts: sun8i: a83t: Correct USB3503 GPIOs polarity

[Sasha Levin]

From: Marek Szyprowski <m.szyprowski@samsung.com>

[ Upstream commit 1c226017d3ec93547b58082bdf778d9db7401c95 ]

Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
index fb928503ad45d..d9be511f054f0 100644
--- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
@@ -101,7 +101,7 @@
 		initial-mode = <1>; /* initialize in HUB mode */
 		disabled-ports = <1>;
 		intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
-		reset-gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+		reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
 		connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
 		refclk-frequency = <19200000>;
 	};
-- 
2.20.1

[PATCH AUTOSEL 5.4 008/107] ARM: dts: sun8i: a83t: Correct USB3503 GPIOs polarity

[Sasha Levin]

From: Marek Szyprowski <m.szyprowski@samsung.com>

[ Upstream commit 1c226017d3ec93547b58082bdf778d9db7401c95 ]

Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
index fb928503ad45d..d9be511f054f0 100644
--- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
@@ -101,7 +101,7 @@
 		initial-mode = <1>; /* initialize in HUB mode */
 		disabled-ports = <1>;
 		intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
-		reset-gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+		reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
 		connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
 		refclk-frequency = <19200000>;
 	};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 009/107] ARM: dts: am57xx-beagle-x15/am57xx-idk: Remove "gpios" for endpoint dt nodes

[Sasha Levin]

From: Kishon Vijay Abraham I <kishon@ti.com>

[ Upstream commit 81cc0877840f72210e809bbedd6346d686560fc1 ]

PERST# line in the PCIE connector is driven by the host mode and not
EP mode. The gpios property here is used for driving the PERST# line.
Remove gpios property from all endpoint device tree nodes.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/am571x-idk.dts                | 4 ----
 arch/arm/boot/dts/am572x-idk-common.dtsi        | 4 ----
 arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 4 ----
 3 files changed, 12 deletions(-)

diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts
index 0aaacea1d887b..975a6b1d3fc80 100644
--- a/arch/arm/boot/dts/am571x-idk.dts
+++ b/arch/arm/boot/dts/am571x-idk.dts
@@ -170,10 +170,6 @@
 	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
 };
 
-&pcie1_ep {
-	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
-};
-
 &mmc1 {
 	pinctrl-names = "default", "hs";
 	pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
diff --git a/arch/arm/boot/dts/am572x-idk-common.dtsi b/arch/arm/boot/dts/am572x-idk-common.dtsi
index a064f13b38802..ddf123620e962 100644
--- a/arch/arm/boot/dts/am572x-idk-common.dtsi
+++ b/arch/arm/boot/dts/am572x-idk-common.dtsi
@@ -147,10 +147,6 @@
 	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
 };
 
-&pcie1_ep {
-	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
-};
-
 &mailbox5 {
 	status = "okay";
 	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index bc76f1705c0f6..9a94c96b0350e 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -547,10 +547,6 @@
 	gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
 };
 
-&pcie1_ep {
-	gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
-};
-
 &mcasp3 {
 	#sound-dai-cells = <0>;
 	assigned-clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
-- 
2.20.1

[PATCH AUTOSEL 5.4 009/107] ARM: dts: am57xx-beagle-x15/am57xx-idk: Remove "gpios" for endpoint dt nodes

[Sasha Levin]

From: Kishon Vijay Abraham I <kishon@ti.com>

[ Upstream commit 81cc0877840f72210e809bbedd6346d686560fc1 ]

PERST# line in the PCIE connector is driven by the host mode and not
EP mode. The gpios property here is used for driving the PERST# line.
Remove gpios property from all endpoint device tree nodes.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/am571x-idk.dts                | 4 ----
 arch/arm/boot/dts/am572x-idk-common.dtsi        | 4 ----
 arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 4 ----
 3 files changed, 12 deletions(-)

diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts
index 0aaacea1d887b..975a6b1d3fc80 100644
--- a/arch/arm/boot/dts/am571x-idk.dts
+++ b/arch/arm/boot/dts/am571x-idk.dts
@@ -170,10 +170,6 @@
 	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
 };
 
-&pcie1_ep {
-	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
-};
-
 &mmc1 {
 	pinctrl-names = "default", "hs";
 	pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
diff --git a/arch/arm/boot/dts/am572x-idk-common.dtsi b/arch/arm/boot/dts/am572x-idk-common.dtsi
index a064f13b38802..ddf123620e962 100644
--- a/arch/arm/boot/dts/am572x-idk-common.dtsi
+++ b/arch/arm/boot/dts/am572x-idk-common.dtsi
@@ -147,10 +147,6 @@
 	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
 };
 
-&pcie1_ep {
-	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
-};
-
 &mailbox5 {
 	status = "okay";
 	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index bc76f1705c0f6..9a94c96b0350e 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -547,10 +547,6 @@
 	gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
 };
 
-&pcie1_ep {
-	gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
-};
-
 &mcasp3 {
 	#sound-dai-cells = <0>;
 	assigned-clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 010/107] ARM: dts: beagle-x15-common: Model 5V0 regulator

[Sasha Levin]

From: Kishon Vijay Abraham I <kishon@ti.com>

[ Upstream commit e17e7c498d4f734df93c300441e100818ed58168 ]

On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../boot/dts/am57xx-beagle-x15-common.dtsi    | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index 9a94c96b0350e..a813a0cf3ff39 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -29,6 +29,27 @@
 		reg = <0x0 0x80000000 0x0 0x80000000>;
 	};
 
+	main_12v0: fixedregulator-main_12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "main_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	evm_5v0: fixedregulator-evm_5v0 {
+		/* Output of TPS54531D */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&main_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	vdd_3v3: fixedregulator-vdd_3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3";
-- 
2.20.1

[PATCH AUTOSEL 5.4 010/107] ARM: dts: beagle-x15-common: Model 5V0 regulator

[Sasha Levin]

From: Kishon Vijay Abraham I <kishon@ti.com>

[ Upstream commit e17e7c498d4f734df93c300441e100818ed58168 ]

On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../boot/dts/am57xx-beagle-x15-common.dtsi    | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index 9a94c96b0350e..a813a0cf3ff39 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -29,6 +29,27 @@
 		reg = <0x0 0x80000000 0x0 0x80000000>;
 	};
 
+	main_12v0: fixedregulator-main_12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "main_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	evm_5v0: fixedregulator-evm_5v0 {
+		/* Output of TPS54531D */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&main_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	vdd_3v3: fixedregulator-vdd_3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3";
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 010/107] ARM: dts: beagle-x15-common: Model 5V0 regulator

[Sasha Levin]

From: Kishon Vijay Abraham I <kishon@ti.com>

[ Upstream commit e17e7c498d4f734df93c300441e100818ed58168 ]

On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../boot/dts/am57xx-beagle-x15-common.dtsi    | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index 9a94c96b0350e..a813a0cf3ff39 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -29,6 +29,27 @@
 		reg = <0x0 0x80000000 0x0 0x80000000>;
 	};
 
+	main_12v0: fixedregulator-main_12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "main_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	evm_5v0: fixedregulator-evm_5v0 {
+		/* Output of TPS54531D */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&main_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	vdd_3v3: fixedregulator-vdd_3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3";
-- 
2.20.1

[PATCH AUTOSEL 5.4 011/107] soc: ti: wkup_m3_ipc: Fix race condition with rproc_boot

[Sasha Levin]

From: Dave Gerlach <d-gerlach@ti.com>

[ Upstream commit 03729cfa0d543bc996bf959e762ec999afc8f3d2 ]

Any user of wkup_m3_ipc calls wkup_m3_ipc_get to get a handle and this
checks the value of the static variable m3_ipc_state to see if the
wkup_m3 is ready. Currently this is populated during probe before
rproc_boot has been called, meaning there is a window of time that
wkup_m3_ipc_get can return a valid handle but the wkup_m3 itself is not
ready, leading to invalid IPC calls to the wkup_m3 and system
instability.

To avoid this, move the population of the m3_ipc_state variable until
after rproc_boot has succeeded to guarantee a valid and usable handle
is always returned.

Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/soc/ti/wkup_m3_ipc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/soc/ti/wkup_m3_ipc.c b/drivers/soc/ti/wkup_m3_ipc.c
index 378369d9364ae..e9ece45d7a333 100644
--- a/drivers/soc/ti/wkup_m3_ipc.c
+++ b/drivers/soc/ti/wkup_m3_ipc.c
@@ -419,6 +419,8 @@ static void wkup_m3_rproc_boot_thread(struct wkup_m3_ipc *m3_ipc)
 	ret = rproc_boot(m3_ipc->rproc);
 	if (ret)
 		dev_err(dev, "rproc_boot failed\n");
+	else
+		m3_ipc_state = m3_ipc;
 
 	do_exit(0);
 }
@@ -505,8 +507,6 @@ static int wkup_m3_ipc_probe(struct platform_device *pdev)
 		goto err_put_rproc;
 	}
 
-	m3_ipc_state = m3_ipc;
-
 	return 0;
 
 err_put_rproc:
-- 
2.20.1

[PATCH AUTOSEL 5.4 011/107] soc: ti: wkup_m3_ipc: Fix race condition with rproc_boot

[Sasha Levin]

From: Dave Gerlach <d-gerlach@ti.com>

[ Upstream commit 03729cfa0d543bc996bf959e762ec999afc8f3d2 ]

Any user of wkup_m3_ipc calls wkup_m3_ipc_get to get a handle and this
checks the value of the static variable m3_ipc_state to see if the
wkup_m3 is ready. Currently this is populated during probe before
rproc_boot has been called, meaning there is a window of time that
wkup_m3_ipc_get can return a valid handle but the wkup_m3 itself is not
ready, leading to invalid IPC calls to the wkup_m3 and system
instability.

To avoid this, move the population of the m3_ipc_state variable until
after rproc_boot has succeeded to guarantee a valid and usable handle
is always returned.

Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/soc/ti/wkup_m3_ipc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/soc/ti/wkup_m3_ipc.c b/drivers/soc/ti/wkup_m3_ipc.c
index 378369d9364ae..e9ece45d7a333 100644
--- a/drivers/soc/ti/wkup_m3_ipc.c
+++ b/drivers/soc/ti/wkup_m3_ipc.c
@@ -419,6 +419,8 @@ static void wkup_m3_rproc_boot_thread(struct wkup_m3_ipc *m3_ipc)
 	ret = rproc_boot(m3_ipc->rproc);
 	if (ret)
 		dev_err(dev, "rproc_boot failed\n");
+	else
+		m3_ipc_state = m3_ipc;
 
 	do_exit(0);
 }
@@ -505,8 +507,6 @@ static int wkup_m3_ipc_probe(struct platform_device *pdev)
 		goto err_put_rproc;
 	}
 
-	m3_ipc_state = m3_ipc;
-
 	return 0;
 
 err_put_rproc:
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 012/107] tools lib traceevent: Fix memory leakage in filter_event

[Sasha Levin]

From: Hewenliang <hewenliang4@huawei.com>

[ Upstream commit f84ae29a6169318f9c929720c49d96323d2bbab9 ]

It is necessary to call free_arg(arg) when add_filter_type() returns NULL
in filter_event().

Signed-off-by: Hewenliang <hewenliang4@huawei.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Feilong Lin <linfeilong@huawei.com>
Cc: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Link: http://lore.kernel.org/lkml/20191209063549.59941-1-hewenliang4@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/lib/traceevent/parse-filter.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/tools/lib/traceevent/parse-filter.c b/tools/lib/traceevent/parse-filter.c
index f3cbf86e51acf..20eed719542e5 100644
--- a/tools/lib/traceevent/parse-filter.c
+++ b/tools/lib/traceevent/parse-filter.c
@@ -1228,8 +1228,10 @@ filter_event(struct tep_event_filter *filter, struct tep_event *event,
 	}
 
 	filter_type = add_filter_type(filter, event->id);
-	if (filter_type == NULL)
+	if (filter_type == NULL) {
+		free_arg(arg);
 		return TEP_ERRNO__MEM_ALLOC_FAILED;
+	}
 
 	if (filter_type->filter)
 		free_arg(filter_type->filter);
-- 
2.20.1

[PATCH AUTOSEL 5.4 013/107] ARM: dts: imx6q-dhcom: fix rtc compatible

[Sasha Levin]

From: Alexandre Belloni <alexandre.belloni@bootlin.com>

[ Upstream commit 7d7778b1396bc9e2a3875009af522beb4ea9355a ]

The only correct and documented compatible string for the rv3029 is
microcrystal,rv3029. Fix it up.

Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6q-dhcom-som.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6q-dhcom-som.dtsi b/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
index 387801dde02e2..08a2e17e0539b 100644
--- a/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
@@ -206,7 +206,7 @@
 	};
 
 	rtc@56 {
-		compatible = "rv3029c2";
+		compatible = "microcrystal,rv3029";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rtc_hw300>;
 		reg = <0x56>;
-- 
2.20.1

[PATCH AUTOSEL 5.4 013/107] ARM: dts: imx6q-dhcom: fix rtc compatible

[Sasha Levin]

From: Alexandre Belloni <alexandre.belloni@bootlin.com>

[ Upstream commit 7d7778b1396bc9e2a3875009af522beb4ea9355a ]

The only correct and documented compatible string for the rv3029 is
microcrystal,rv3029. Fix it up.

Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6q-dhcom-som.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6q-dhcom-som.dtsi b/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
index 387801dde02e2..08a2e17e0539b 100644
--- a/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
@@ -206,7 +206,7 @@
 	};
 
 	rtc@56 {
-		compatible = "rv3029c2";
+		compatible = "microcrystal,rv3029";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rtc_hw300>;
 		reg = <0x56>;
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 014/107] arm64: dts: ls1028a: fix endian setting for dcfg

[Sasha Levin]

From: Yinbo Zhu <yinbo.zhu@nxp.com>

[ Upstream commit 33eae7fb2e593fdbaac15d843e2558379c6d1149 ]

DCFG block uses little endian.  Fix it so that register access becomes
correct.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index bb960fe2bb64c..9589b15693d6e 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -158,7 +158,7 @@
 		dcfg: syscon@1e00000 {
 			compatible = "fsl,ls1028a-dcfg", "syscon";
 			reg = <0x0 0x1e00000 0x0 0x10000>;
-			big-endian;
+			little-endian;
 		};
 
 		rst: syscon@1e60000 {
-- 
2.20.1

[PATCH AUTOSEL 5.4 014/107] arm64: dts: ls1028a: fix endian setting for dcfg

[Sasha Levin]

From: Yinbo Zhu <yinbo.zhu@nxp.com>

[ Upstream commit 33eae7fb2e593fdbaac15d843e2558379c6d1149 ]

DCFG block uses little endian.  Fix it so that register access becomes
correct.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index bb960fe2bb64c..9589b15693d6e 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -158,7 +158,7 @@
 		dcfg: syscon@1e00000 {
 			compatible = "fsl,ls1028a-dcfg", "syscon";
 			reg = <0x0 0x1e00000 0x0 0x10000>;
-			big-endian;
+			little-endian;
 		};
 
 		rst: syscon@1e60000 {
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 015/107] arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm

[Sasha Levin]

From: Adam Ford <aford173@gmail.com>

[ Upstream commit 24a572bf67994223e722cadfe663e15ba221882a ]

Using SDMA1 with UART1 is causing a "Timeout waiting for CH0" error.
This patch changes to ahb clock from SDMA1_ROOT to AHB which
fixes the timeout error.

Fixes:  a05ea40eb384 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mm.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 23c8fad7932b1..b4ca3b7ef10d5 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -741,7 +741,7 @@
 				reg = <0x30bd0000 0x10000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MM_CLK_SDMA1_ROOT>,
-					 <&clk IMX8MM_CLK_SDMA1_ROOT>;
+					 <&clk IMX8MM_CLK_AHB>;
 				clock-names = "ipg", "ahb";
 				#dma-cells = <3>;
 				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
-- 
2.20.1

[PATCH AUTOSEL 5.4 015/107] arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm

[Sasha Levin]

From: Adam Ford <aford173@gmail.com>

[ Upstream commit 24a572bf67994223e722cadfe663e15ba221882a ]

Using SDMA1 with UART1 is causing a "Timeout waiting for CH0" error.
This patch changes to ahb clock from SDMA1_ROOT to AHB which
fixes the timeout error.

Fixes:  a05ea40eb384 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mm.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 23c8fad7932b1..b4ca3b7ef10d5 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -741,7 +741,7 @@
 				reg = <0x30bd0000 0x10000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MM_CLK_SDMA1_ROOT>,
-					 <&clk IMX8MM_CLK_SDMA1_ROOT>;
+					 <&clk IMX8MM_CLK_AHB>;
 				clock-names = "ipg", "ahb";
 				#dma-cells = <3>;
 				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 016/107] ARM: dts: imx7ulp: fix reg of cpu node

[Sasha Levin]

From: Peng Fan <peng.fan@nxp.com>

[ Upstream commit b8ab62ff7199fac8ce27fa4a149929034fabe7f8 ]

According to arm cpus binding doc,
"
      On 32-bit ARM v7 or later systems this property is
        required and matches the CPU MPIDR[23:0] register
        bits.

        Bits [23:0] in the reg cell must be set to
        bits [23:0] in MPIDR.

        All other bits in the reg cell must be set to 0.
"

In i.MX7ULP, the MPIDR[23:0] is 0xf00, not 0, so fix it.
Otherwise there will be warning:
"DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map"

Fixes: 20434dc92c05 ("ARM: dts: imx: add common imx7ulp dtsi support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx7ulp.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx7ulp.dtsi b/arch/arm/boot/dts/imx7ulp.dtsi
index 6859a3a83750c..3dac6898cdc57 100644
--- a/arch/arm/boot/dts/imx7ulp.dtsi
+++ b/arch/arm/boot/dts/imx7ulp.dtsi
@@ -37,10 +37,10 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu0: cpu@0 {
+		cpu0: cpu@f00 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
-			reg = <0>;
+			reg = <0xf00>;
 		};
 	};
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 016/107] ARM: dts: imx7ulp: fix reg of cpu node

[Sasha Levin]

From: Peng Fan <peng.fan@nxp.com>

[ Upstream commit b8ab62ff7199fac8ce27fa4a149929034fabe7f8 ]

According to arm cpus binding doc,
"
      On 32-bit ARM v7 or later systems this property is
        required and matches the CPU MPIDR[23:0] register
        bits.

        Bits [23:0] in the reg cell must be set to
        bits [23:0] in MPIDR.

        All other bits in the reg cell must be set to 0.
"

In i.MX7ULP, the MPIDR[23:0] is 0xf00, not 0, so fix it.
Otherwise there will be warning:
"DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map"

Fixes: 20434dc92c05 ("ARM: dts: imx: add common imx7ulp dtsi support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx7ulp.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx7ulp.dtsi b/arch/arm/boot/dts/imx7ulp.dtsi
index 6859a3a83750c..3dac6898cdc57 100644
--- a/arch/arm/boot/dts/imx7ulp.dtsi
+++ b/arch/arm/boot/dts/imx7ulp.dtsi
@@ -37,10 +37,10 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu0: cpu@0 {
+		cpu0: cpu@f00 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
-			reg = <0>;
+			reg = <0xf00>;
 		};
 	};
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 017/107] ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit fe6a6689d1815b63528796886853890d8ee7f021 ]

The SGTL5000 VDDIO is connected to the PMIC SW2 output, not to
a fixed 3V3 rail. Describe this correctly in the DT.

Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6q-dhcom-pdk2.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts b/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
index 9c61e3be2d9a3..1c46df6827f50 100644
--- a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
+++ b/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
@@ -55,7 +55,7 @@
 		#sound-dai-cells = <0>;
 		clocks = <&clk_ext_audio_codec>;
 		VDDA-supply = <&reg_3p3v>;
-		VDDIO-supply = <&reg_3p3v>;
+		VDDIO-supply = <&sw2_reg>;
 	};
 };
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 017/107] ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit fe6a6689d1815b63528796886853890d8ee7f021 ]

The SGTL5000 VDDIO is connected to the PMIC SW2 output, not to
a fixed 3V3 rail. Describe this correctly in the DT.

Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6q-dhcom-pdk2.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts b/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
index 9c61e3be2d9a3..1c46df6827f50 100644
--- a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
+++ b/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
@@ -55,7 +55,7 @@
 		#sound-dai-cells = <0>;
 		clocks = <&clk_ext_audio_codec>;
 		VDDA-supply = <&reg_3p3v>;
-		VDDIO-supply = <&reg_3p3v>;
+		VDDIO-supply = <&sw2_reg>;
 	};
 };
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 018/107] arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer

[Sasha Levin]

From: "Angus Ainslie (Purism)" <angus@akkea.ca>

[ Upstream commit 106f7b3bf943d267eb657f34616adcaadb2ab07f ]

The LSM9DS1 uses a high level interrupt.

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Fixes: eb4ea0857c83 ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index 683a110356431..98cfe67b7db7b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -421,7 +421,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_imu>;
 		interrupt-parent = <&gpio3>;
-		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
 		vdd-supply = <&reg_3v3_p>;
 		vddio-supply = <&reg_3v3_p>;
 	};
-- 
2.20.1

[PATCH AUTOSEL 5.4 018/107] arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer

[Sasha Levin]

From: "Angus Ainslie (Purism)" <angus@akkea.ca>

[ Upstream commit 106f7b3bf943d267eb657f34616adcaadb2ab07f ]

The LSM9DS1 uses a high level interrupt.

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Fixes: eb4ea0857c83 ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index 683a110356431..98cfe67b7db7b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -421,7 +421,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_imu>;
 		interrupt-parent = <&gpio3>;
-		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
 		vdd-supply = <&reg_3v3_p>;
 		vddio-supply = <&reg_3v3_p>;
 	};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 019/107] rseq: Unregister rseq for clone CLONE_VM

[Sasha Levin]

From: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>

[ Upstream commit 463f550fb47bede3a5d7d5177f363a6c3b45d50b ]

It has been reported by Google that rseq is not behaving properly
with respect to clone when CLONE_VM is used without CLONE_THREAD.

It keeps the prior thread's rseq TLS registered when the TLS of the
thread has moved, so the kernel can corrupt the TLS of the parent.

The approach of clearing the per task-struct rseq registration
on clone with CLONE_THREAD flag is incomplete. It does not cover
the use-case of clone with CLONE_VM set, but without CLONE_THREAD.

Here is the rationale for unregistering rseq on clone with CLONE_VM
flag set:

1) CLONE_THREAD requires CLONE_SIGHAND, which requires CLONE_VM to be
   set. Therefore, just checking for CLONE_VM covers all CLONE_THREAD
   uses. There is no point in checking for both CLONE_THREAD and
   CLONE_VM,

2) There is the possibility of an unlikely scenario where CLONE_SETTLS
   is used without CLONE_VM. In order to be an issue, it would require
   that the rseq TLS is in a shared memory area.

   I do not plan on adding CLONE_SETTLS to the set of clone flags which
   unregister RSEQ, because it would require that we also unregister RSEQ
   on set_thread_area(2) and arch_prctl(2) ARCH_SET_FS for completeness.
   So rather than doing a partial solution, it appears better to let
   user-space explicitly perform rseq unregistration across clone if
   needed in scenarios where CLONE_VM is not set.

Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191211161713.4490-3-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/linux/sched.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/include/linux/sched.h b/include/linux/sched.h
index 775503573ed70..b968d736833bb 100644
--- a/include/linux/sched.h
+++ b/include/linux/sched.h
@@ -1915,11 +1915,11 @@ static inline void rseq_migrate(struct task_struct *t)
 
 /*
  * If parent process has a registered restartable sequences area, the
- * child inherits. Only applies when forking a process, not a thread.
+ * child inherits. Unregister rseq for a clone with CLONE_VM set.
  */
 static inline void rseq_fork(struct task_struct *t, unsigned long clone_flags)
 {
-	if (clone_flags & CLONE_THREAD) {
+	if (clone_flags & CLONE_VM) {
 		t->rseq = NULL;
 		t->rseq_sig = 0;
 		t->rseq_event_mask = 0;
-- 
2.20.1

[PATCH AUTOSEL 5.4 020/107] locking/lockdep: Fix buffer overrun problem in stack_trace[]

[Sasha Levin]

From: Waiman Long <longman@redhat.com>

[ Upstream commit d91f3057263ceb691ef527e71b41a56b17f6c869 ]

If the lockdep code is really running out of the stack_trace entries,
it is likely that buffer overrun can happen and the data immediately
after stack_trace[] will be corrupted.

If there is less than LOCK_TRACE_SIZE_IN_LONGS entries left before
the call to save_trace(), the max_entries computation will leave it
with a very large positive number because of its unsigned nature. The
subsequent call to stack_trace_save() will then corrupt the data after
stack_trace[]. Fix that by changing max_entries to a signed integer
and check for negative value before calling stack_trace_save().

Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 12593b7467f9 ("locking/lockdep: Reduce space occupied by stack traces")
Link: https://lkml.kernel.org/r/20191220135128.14876-1-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/locking/lockdep.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/kernel/locking/lockdep.c b/kernel/locking/lockdep.c
index 233459c03b5ae..35d3b6925b1ee 100644
--- a/kernel/locking/lockdep.c
+++ b/kernel/locking/lockdep.c
@@ -482,7 +482,7 @@ static struct lock_trace *save_trace(void)
 	struct lock_trace *trace, *t2;
 	struct hlist_head *hash_head;
 	u32 hash;
-	unsigned int max_entries;
+	int max_entries;
 
 	BUILD_BUG_ON_NOT_POWER_OF_2(STACK_TRACE_HASH_SIZE);
 	BUILD_BUG_ON(LOCK_TRACE_SIZE_IN_LONGS >= MAX_STACK_TRACE_ENTRIES);
@@ -490,10 +490,8 @@ static struct lock_trace *save_trace(void)
 	trace = (struct lock_trace *)(stack_trace + nr_stack_trace_entries);
 	max_entries = MAX_STACK_TRACE_ENTRIES - nr_stack_trace_entries -
 		LOCK_TRACE_SIZE_IN_LONGS;
-	trace->nr_entries = stack_trace_save(trace->entries, max_entries, 3);
 
-	if (nr_stack_trace_entries >= MAX_STACK_TRACE_ENTRIES -
-	    LOCK_TRACE_SIZE_IN_LONGS - 1) {
+	if (max_entries <= 0) {
 		if (!debug_locks_off_graph_unlock())
 			return NULL;
 
@@ -502,6 +500,7 @@ static struct lock_trace *save_trace(void)
 
 		return NULL;
 	}
+	trace->nr_entries = stack_trace_save(trace->entries, max_entries, 3);
 
 	hash = jhash(trace->entries, trace->nr_entries *
 		     sizeof(trace->entries[0]), 0);
-- 
2.20.1

[PATCH AUTOSEL 5.4 021/107] efi/earlycon: Fix write-combine mapping on x86

[Sasha Levin]

From: Arvind Sankar <nivedita@alum.mit.edu>

[ Upstream commit d92b54570d24d017d2630e314b525ed792f5aa6c ]

On x86, until PAT is initialized, WC translates into UC-. Since we
calculate and store pgprot_writecombine(PAGE_KERNEL) when earlycon is
initialized, this means we actually use UC- mappings instead of WC
mappings, which makes scrolling very slow.

Instead store a boolean flag to indicate whether we want to use
writeback or write-combine mappings, and recalculate the actual pgprot_t
we need on every mapping. Once PAT is initialized, we will start using
write-combine mappings, which speeds up the scrolling considerably.

Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 69c1f396f25b ("efi/x86: Convert x86 EFI earlyprintk into generic earlycon implementation")
Link: https://lkml.kernel.org/r/20191224132909.102540-2-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/firmware/efi/earlycon.c | 16 +++++++---------
 1 file changed, 7 insertions(+), 9 deletions(-)

diff --git a/drivers/firmware/efi/earlycon.c b/drivers/firmware/efi/earlycon.c
index d4077db6dc97f..5d4f84781aa03 100644
--- a/drivers/firmware/efi/earlycon.c
+++ b/drivers/firmware/efi/earlycon.c
@@ -17,7 +17,7 @@ static const struct console *earlycon_console __initdata;
 static const struct font_desc *font;
 static u32 efi_x, efi_y;
 static u64 fb_base;
-static pgprot_t fb_prot;
+static bool fb_wb;
 static void *efi_fb;
 
 /*
@@ -33,10 +33,8 @@ static int __init efi_earlycon_remap_fb(void)
 	if (!earlycon_console || !(earlycon_console->flags & CON_ENABLED))
 		return 0;
 
-	if (pgprot_val(fb_prot) == pgprot_val(PAGE_KERNEL))
-		efi_fb = memremap(fb_base, screen_info.lfb_size, MEMREMAP_WB);
-	else
-		efi_fb = memremap(fb_base, screen_info.lfb_size, MEMREMAP_WC);
+	efi_fb = memremap(fb_base, screen_info.lfb_size,
+			  fb_wb ? MEMREMAP_WB : MEMREMAP_WC);
 
 	return efi_fb ? 0 : -ENOMEM;
 }
@@ -53,9 +51,12 @@ late_initcall(efi_earlycon_unmap_fb);
 
 static __ref void *efi_earlycon_map(unsigned long start, unsigned long len)
 {
+	pgprot_t fb_prot;
+
 	if (efi_fb)
 		return efi_fb + start;
 
+	fb_prot = fb_wb ? PAGE_KERNEL : pgprot_writecombine(PAGE_KERNEL);
 	return early_memremap_prot(fb_base + start, len, pgprot_val(fb_prot));
 }
 
@@ -215,10 +216,7 @@ static int __init efi_earlycon_setup(struct earlycon_device *device,
 	if (screen_info.capabilities & VIDEO_CAPABILITY_64BIT_BASE)
 		fb_base |= (u64)screen_info.ext_lfb_base << 32;
 
-	if (opt && !strcmp(opt, "ram"))
-		fb_prot = PAGE_KERNEL;
-	else
-		fb_prot = pgprot_writecombine(PAGE_KERNEL);
+	fb_wb = opt && !strcmp(opt, "ram");
 
 	si = &screen_info;
 	xres = si->lfb_width;
-- 
2.20.1

[PATCH AUTOSEL 5.4 022/107] clk: Don't try to enable critical clocks if prepare failed

[Sasha Levin]

From: Guenter Roeck <linux@roeck-us.net>

[ Upstream commit 12ead77432f2ce32dea797742316d15c5800cb32 ]

The following traceback is seen if a critical clock fails to prepare.

bcm2835-clk 3f101000.cprman: plld: couldn't lock PLL
------------[ cut here ]------------
Enabling unprepared plld_per
WARNING: CPU: 1 PID: 1 at drivers/clk/clk.c:1014 clk_core_enable+0xcc/0x2c0
...
Call trace:
 clk_core_enable+0xcc/0x2c0
 __clk_register+0x5c4/0x788
 devm_clk_hw_register+0x4c/0xb0
 bcm2835_register_pll_divider+0xc0/0x150
 bcm2835_clk_probe+0x134/0x1e8
 platform_drv_probe+0x50/0xa0
 really_probe+0xd4/0x308
 driver_probe_device+0x54/0xe8
 device_driver_attach+0x6c/0x78
 __driver_attach+0x54/0xd8
...

Check return values from clk_core_prepare() and clk_core_enable() and
bail out if any of those functions returns an error.

Cc: Jerome Brunet <jbrunet@baylibre.com>
Fixes: 99652a469df1 ("clk: migrate the count of orphaned clocks at init")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20191225163429.29694-1-linux@roeck-us.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/clk.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index 4fc294c2f9e8f..67f592fa083ab 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -3408,11 +3408,17 @@ static int __clk_core_init(struct clk_core *core)
 	if (core->flags & CLK_IS_CRITICAL) {
 		unsigned long flags;
 
-		clk_core_prepare(core);
+		ret = clk_core_prepare(core);
+		if (ret)
+			goto out;
 
 		flags = clk_enable_lock();
-		clk_core_enable(core);
+		ret = clk_core_enable(core);
 		clk_enable_unlock(flags);
+		if (ret) {
+			clk_core_unprepare(core);
+			goto out;
+		}
 	}
 
 	clk_core_reparent_orphans_nolock();
-- 
2.20.1

[PATCH AUTOSEL 5.4 023/107] clk: sunxi-ng: sun8i-r: Fix divider on APB0 clock

[Sasha Levin]

From: Samuel Holland <samuel@sholland.org>

[ Upstream commit 47d64fef1f3ffbdf960d3330b9865fc9f12fdf84 ]

According to the BSP source code, the APB0 clock on the H3 and H5 has a
normal M divider, not a power-of-two divider. This matches the hardware
in the A83T (as described in both the BSP source code and the manual).
Since the A83T and H3/A64 clocks are actually the same, we can merge the
definitions.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/sunxi-ng/ccu-sun8i-r.c | 21 +++------------------
 1 file changed, 3 insertions(+), 18 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-r.c b/drivers/clk/sunxi-ng/ccu-sun8i-r.c
index 4646fdc61053b..4c8c491b87c27 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-r.c
@@ -51,19 +51,7 @@ static struct ccu_div ar100_clk = {
 
 static CLK_FIXED_FACTOR_HW(ahb0_clk, "ahb0", &ar100_clk.common.hw, 1, 1, 0);
 
-static struct ccu_div apb0_clk = {
-	.div		= _SUNXI_CCU_DIV_FLAGS(0, 2, CLK_DIVIDER_POWER_OF_TWO),
-
-	.common		= {
-		.reg		= 0x0c,
-		.hw.init	= CLK_HW_INIT_HW("apb0",
-						 &ahb0_clk.hw,
-						 &ccu_div_ops,
-						 0),
-	},
-};
-
-static SUNXI_CCU_M(a83t_apb0_clk, "apb0", "ahb0", 0x0c, 0, 2, 0);
+static SUNXI_CCU_M(apb0_clk, "apb0", "ahb0", 0x0c, 0, 2, 0);
 
 /*
  * Define the parent as an array that can be reused to save space
@@ -127,7 +115,7 @@ static struct ccu_mp a83t_ir_clk = {
 
 static struct ccu_common *sun8i_a83t_r_ccu_clks[] = {
 	&ar100_clk.common,
-	&a83t_apb0_clk.common,
+	&apb0_clk.common,
 	&apb0_pio_clk.common,
 	&apb0_ir_clk.common,
 	&apb0_timer_clk.common,
@@ -167,7 +155,7 @@ static struct clk_hw_onecell_data sun8i_a83t_r_hw_clks = {
 	.hws	= {
 		[CLK_AR100]		= &ar100_clk.common.hw,
 		[CLK_AHB0]		= &ahb0_clk.hw,
-		[CLK_APB0]		= &a83t_apb0_clk.common.hw,
+		[CLK_APB0]		= &apb0_clk.common.hw,
 		[CLK_APB0_PIO]		= &apb0_pio_clk.common.hw,
 		[CLK_APB0_IR]		= &apb0_ir_clk.common.hw,
 		[CLK_APB0_TIMER]	= &apb0_timer_clk.common.hw,
@@ -282,9 +270,6 @@ static void __init sunxi_r_ccu_init(struct device_node *node,
 
 static void __init sun8i_a83t_r_ccu_setup(struct device_node *node)
 {
-	/* Fix apb0 bus gate parents here */
-	apb0_gate_parent[0] = &a83t_apb0_clk.common.hw;
-
 	sunxi_r_ccu_init(node, &sun8i_a83t_r_ccu_desc);
 }
 CLK_OF_DECLARE(sun8i_a83t_r_ccu, "allwinner,sun8i-a83t-r-ccu",
-- 
2.20.1

[PATCH AUTOSEL 5.4 023/107] clk: sunxi-ng: sun8i-r: Fix divider on APB0 clock

[Sasha Levin]

From: Samuel Holland <samuel@sholland.org>

[ Upstream commit 47d64fef1f3ffbdf960d3330b9865fc9f12fdf84 ]

According to the BSP source code, the APB0 clock on the H3 and H5 has a
normal M divider, not a power-of-two divider. This matches the hardware
in the A83T (as described in both the BSP source code and the manual).
Since the A83T and H3/A64 clocks are actually the same, we can merge the
definitions.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/sunxi-ng/ccu-sun8i-r.c | 21 +++------------------
 1 file changed, 3 insertions(+), 18 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-r.c b/drivers/clk/sunxi-ng/ccu-sun8i-r.c
index 4646fdc61053b..4c8c491b87c27 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-r.c
@@ -51,19 +51,7 @@ static struct ccu_div ar100_clk = {
 
 static CLK_FIXED_FACTOR_HW(ahb0_clk, "ahb0", &ar100_clk.common.hw, 1, 1, 0);
 
-static struct ccu_div apb0_clk = {
-	.div		= _SUNXI_CCU_DIV_FLAGS(0, 2, CLK_DIVIDER_POWER_OF_TWO),
-
-	.common		= {
-		.reg		= 0x0c,
-		.hw.init	= CLK_HW_INIT_HW("apb0",
-						 &ahb0_clk.hw,
-						 &ccu_div_ops,
-						 0),
-	},
-};
-
-static SUNXI_CCU_M(a83t_apb0_clk, "apb0", "ahb0", 0x0c, 0, 2, 0);
+static SUNXI_CCU_M(apb0_clk, "apb0", "ahb0", 0x0c, 0, 2, 0);
 
 /*
  * Define the parent as an array that can be reused to save space
@@ -127,7 +115,7 @@ static struct ccu_mp a83t_ir_clk = {
 
 static struct ccu_common *sun8i_a83t_r_ccu_clks[] = {
 	&ar100_clk.common,
-	&a83t_apb0_clk.common,
+	&apb0_clk.common,
 	&apb0_pio_clk.common,
 	&apb0_ir_clk.common,
 	&apb0_timer_clk.common,
@@ -167,7 +155,7 @@ static struct clk_hw_onecell_data sun8i_a83t_r_hw_clks = {
 	.hws	= {
 		[CLK_AR100]		= &ar100_clk.common.hw,
 		[CLK_AHB0]		= &ahb0_clk.hw,
-		[CLK_APB0]		= &a83t_apb0_clk.common.hw,
+		[CLK_APB0]		= &apb0_clk.common.hw,
 		[CLK_APB0_PIO]		= &apb0_pio_clk.common.hw,
 		[CLK_APB0_IR]		= &apb0_ir_clk.common.hw,
 		[CLK_APB0_TIMER]	= &apb0_timer_clk.common.hw,
@@ -282,9 +270,6 @@ static void __init sunxi_r_ccu_init(struct device_node *node,
 
 static void __init sun8i_a83t_r_ccu_setup(struct device_node *node)
 {
-	/* Fix apb0 bus gate parents here */
-	apb0_gate_parent[0] = &a83t_apb0_clk.common.hw;
-
 	sunxi_r_ccu_init(node, &sun8i_a83t_r_ccu_desc);
 }
 CLK_OF_DECLARE(sun8i_a83t_r_ccu, "allwinner,sun8i-a83t-r-ccu",
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 024/107] clk: sunxi-ng: h6-r: Fix AR100/R_APB2 parent order

[Sasha Levin]

From: Samuel Holland <samuel@sholland.org>

[ Upstream commit 0c545240aebc2ccb8f661dc54283a14d64659804 ]

According to the BSP source code, both the AR100 and R_APB2 clocks have
PLL_PERIPH0 as mux index 3, not 2 as it was on previous chips. The pre-
divider used for PLL_PERIPH0 should be changed to index 3 to match.

This was verified by running a rough benchmark on the AR100 with various
clock settings:

        | mux | pre-divider | iterations/second | clock source |
        |=====|=============|===================|==============|
        |   0 |           0 |  19033   (stable) |       osc24M |
        |   2 |           5 |  11466 (unstable) |  iosc/osc16M |
        |   2 |          17 |  11422 (unstable) |  iosc/osc16M |
        |   3 |           5 |  85338   (stable) |  pll-periph0 |
        |   3 |          17 |  27167   (stable) |  pll-periph0 |

The relative performance numbers all match up (with pll-periph0 running
at its default 600MHz).

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
index 45a1ed3fe6742..ab194143e06ce 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
@@ -23,9 +23,9 @@
  */
 
 static const char * const ar100_r_apb2_parents[] = { "osc24M", "osc32k",
-					     "pll-periph0", "iosc" };
+						     "iosc", "pll-periph0" };
 static const struct ccu_mux_var_prediv ar100_r_apb2_predivs[] = {
-	{ .index = 2, .shift = 0, .width = 5 },
+	{ .index = 3, .shift = 0, .width = 5 },
 };
 
 static struct ccu_div ar100_clk = {
-- 
2.20.1

[PATCH AUTOSEL 5.4 024/107] clk: sunxi-ng: h6-r: Fix AR100/R_APB2 parent order

[Sasha Levin]

From: Samuel Holland <samuel@sholland.org>

[ Upstream commit 0c545240aebc2ccb8f661dc54283a14d64659804 ]

According to the BSP source code, both the AR100 and R_APB2 clocks have
PLL_PERIPH0 as mux index 3, not 2 as it was on previous chips. The pre-
divider used for PLL_PERIPH0 should be changed to index 3 to match.

This was verified by running a rough benchmark on the AR100 with various
clock settings:

        | mux | pre-divider | iterations/second | clock source |
        |=====|=============|===================|==============|
        |   0 |           0 |  19033   (stable) |       osc24M |
        |   2 |           5 |  11466 (unstable) |  iosc/osc16M |
        |   2 |          17 |  11422 (unstable) |  iosc/osc16M |
        |   3 |           5 |  85338   (stable) |  pll-periph0 |
        |   3 |          17 |  27167   (stable) |  pll-periph0 |

The relative performance numbers all match up (with pll-periph0 running
at its default 600MHz).

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
index 45a1ed3fe6742..ab194143e06ce 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
@@ -23,9 +23,9 @@
  */
 
 static const char * const ar100_r_apb2_parents[] = { "osc24M", "osc32k",
-					     "pll-periph0", "iosc" };
+						     "iosc", "pll-periph0" };
 static const struct ccu_mux_var_prediv ar100_r_apb2_predivs[] = {
-	{ .index = 2, .shift = 0, .width = 5 },
+	{ .index = 3, .shift = 0, .width = 5 },
 };
 
 static struct ccu_div ar100_clk = {
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 025/107] mac80211: mesh: restrict airtime metric to peered established plinks

[Sasha Levin]

From: Markus Theil <markus.theil@tu-ilmenau.de>

[ Upstream commit 02a614499600af836137c3fbc4404cd96365fff2 ]

The following warning is triggered every time an unestablished mesh peer
gets dumped. Checks if a peer link is established before retrieving the
airtime link metric.

[ 9563.022567] WARNING: CPU: 0 PID: 6287 at net/mac80211/mesh_hwmp.c:345
               airtime_link_metric_get+0xa2/0xb0 [mac80211]
[ 9563.022697] Hardware name: PC Engines apu2/apu2, BIOS v4.10.0.3
[ 9563.022756] RIP: 0010:airtime_link_metric_get+0xa2/0xb0 [mac80211]
[ 9563.022838] Call Trace:
[ 9563.022897]  sta_set_sinfo+0x936/0xa10 [mac80211]
[ 9563.022964]  ieee80211_dump_station+0x6d/0x90 [mac80211]
[ 9563.023062]  nl80211_dump_station+0x154/0x2a0 [cfg80211]
[ 9563.023120]  netlink_dump+0x17b/0x370
[ 9563.023130]  netlink_recvmsg+0x2a4/0x480
[ 9563.023140]  ____sys_recvmsg+0xa6/0x160
[ 9563.023154]  ___sys_recvmsg+0x93/0xe0
[ 9563.023169]  __sys_recvmsg+0x7e/0xd0
[ 9563.023210]  do_syscall_64+0x4e/0x140
[ 9563.023217]  entry_SYSCALL_64_after_hwframe+0x44/0xa9

Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20191203180644.70653-1-markus.theil@tu-ilmenau.de
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/mac80211/mesh_hwmp.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/net/mac80211/mesh_hwmp.c b/net/mac80211/mesh_hwmp.c
index 68af623063858..d699833703819 100644
--- a/net/mac80211/mesh_hwmp.c
+++ b/net/mac80211/mesh_hwmp.c
@@ -328,6 +328,9 @@ u32 airtime_link_metric_get(struct ieee80211_local *local,
 	unsigned long fail_avg =
 		ewma_mesh_fail_avg_read(&sta->mesh->fail_avg);
 
+	if (sta->mesh->plink_state != NL80211_PLINK_ESTAB)
+		return MAX_METRIC;
+
 	/* Try to get rate based on HW/SW RC algorithm.
 	 * Rate is returned in units of Kbps, correct this
 	 * to comply with airtime calculation units
-- 
2.20.1

[PATCH AUTOSEL 5.4 026/107] x86/resctrl: Fix potential memory leak

[Sasha Levin]

From: Shakeel Butt <shakeelb@google.com>

[ Upstream commit ab6a2114433a3b5b555983dcb9b752a85255f04b ]

set_cache_qos_cfg() is leaking memory when the given level is not
RDT_RESOURCE_L3 or RDT_RESOURCE_L2. At the moment, this function is
called with only valid levels but move the allocation after the valid
level checks in order to make it more robust and future proof.

 [ bp: Massage commit message. ]

Fixes: 99adde9b370de ("x86/intel_rdt: Enable L2 CDP in MSR IA32_L2_QOS_CFG")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20200102165844.133133-1-shakeelb@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/kernel/cpu/resctrl/rdtgroup.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/x86/kernel/cpu/resctrl/rdtgroup.c b/arch/x86/kernel/cpu/resctrl/rdtgroup.c
index 2e3b06d6bbc6d..dac7209a07084 100644
--- a/arch/x86/kernel/cpu/resctrl/rdtgroup.c
+++ b/arch/x86/kernel/cpu/resctrl/rdtgroup.c
@@ -1741,9 +1741,6 @@ static int set_cache_qos_cfg(int level, bool enable)
 	struct rdt_domain *d;
 	int cpu;
 
-	if (!zalloc_cpumask_var(&cpu_mask, GFP_KERNEL))
-		return -ENOMEM;
-
 	if (level == RDT_RESOURCE_L3)
 		update = l3_qos_cfg_update;
 	else if (level == RDT_RESOURCE_L2)
@@ -1751,6 +1748,9 @@ static int set_cache_qos_cfg(int level, bool enable)
 	else
 		return -EINVAL;
 
+	if (!zalloc_cpumask_var(&cpu_mask, GFP_KERNEL))
+		return -ENOMEM;
+
 	r_l = &rdt_resources_all[level];
 	list_for_each_entry(d, &r_l->domains, list) {
 		/* Pick one CPU from each domain instance to update MSR */
-- 
2.20.1

[PATCH AUTOSEL 5.4 027/107] clk: qcom: gcc-sdm845: Add missing flag to votable GDSCs

[Sasha Levin]

From: Georgi Djakov <georgi.djakov@linaro.org>

[ Upstream commit 5e82548e26ef62e257dc2ff37c11acb5eb72728e ]

On sdm845 devices, during boot we see the following warnings (unless we
have added 'pd_ignore_unused' to the kernel command line):
	hlos1_vote_mmnoc_mmu_tbu_sf_gdsc status stuck at 'on'
	hlos1_vote_mmnoc_mmu_tbu_hf1_gdsc status stuck at 'on'
	hlos1_vote_mmnoc_mmu_tbu_hf0_gdsc status stuck at 'on'
	hlos1_vote_aggre_noc_mmu_tbu2_gdsc status stuck at 'on'
	hlos1_vote_aggre_noc_mmu_tbu1_gdsc status stuck at 'on'
	hlos1_vote_aggre_noc_mmu_pcie_tbu_gdsc status stuck at 'on'
	hlos1_vote_aggre_noc_mmu_audio_tbu_gdsc status stuck at 'on'

As the name of these GDSCs suggests, they are "votable" and in downstream
DT, they all have the property "qcom,no-status-check-on-disable", which
means that we should not poll the status bit when we disable them.

Luckily the VOTABLE flag already exists and it does exactly what we need,
so let's make use of it to make the warnings disappear.

Fixes: 06391eddb60a ("clk: qcom: Add Global Clock controller (GCC) driver for SDM845")
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lkml.kernel.org/r/20191126153437.11808-1-georgi.djakov@linaro.org
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/qcom/gcc-sdm845.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/clk/qcom/gcc-sdm845.c b/drivers/clk/qcom/gcc-sdm845.c
index 95be125c3bddf..56d22dd225c9d 100644
--- a/drivers/clk/qcom/gcc-sdm845.c
+++ b/drivers/clk/qcom/gcc-sdm845.c
@@ -3255,6 +3255,7 @@ static struct gdsc hlos1_vote_aggre_noc_mmu_audio_tbu_gdsc = {
 		.name = "hlos1_vote_aggre_noc_mmu_audio_tbu_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.flags = VOTABLE,
 };
 
 static struct gdsc hlos1_vote_aggre_noc_mmu_pcie_tbu_gdsc = {
@@ -3263,6 +3264,7 @@ static struct gdsc hlos1_vote_aggre_noc_mmu_pcie_tbu_gdsc = {
 		.name = "hlos1_vote_aggre_noc_mmu_pcie_tbu_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.flags = VOTABLE,
 };
 
 static struct gdsc hlos1_vote_aggre_noc_mmu_tbu1_gdsc = {
@@ -3271,6 +3273,7 @@ static struct gdsc hlos1_vote_aggre_noc_mmu_tbu1_gdsc = {
 		.name = "hlos1_vote_aggre_noc_mmu_tbu1_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.flags = VOTABLE,
 };
 
 static struct gdsc hlos1_vote_aggre_noc_mmu_tbu2_gdsc = {
@@ -3279,6 +3282,7 @@ static struct gdsc hlos1_vote_aggre_noc_mmu_tbu2_gdsc = {
 		.name = "hlos1_vote_aggre_noc_mmu_tbu2_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.flags = VOTABLE,
 };
 
 static struct gdsc hlos1_vote_mmnoc_mmu_tbu_hf0_gdsc = {
@@ -3287,6 +3291,7 @@ static struct gdsc hlos1_vote_mmnoc_mmu_tbu_hf0_gdsc = {
 		.name = "hlos1_vote_mmnoc_mmu_tbu_hf0_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.flags = VOTABLE,
 };
 
 static struct gdsc hlos1_vote_mmnoc_mmu_tbu_hf1_gdsc = {
@@ -3295,6 +3300,7 @@ static struct gdsc hlos1_vote_mmnoc_mmu_tbu_hf1_gdsc = {
 		.name = "hlos1_vote_mmnoc_mmu_tbu_hf1_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.flags = VOTABLE,
 };
 
 static struct gdsc hlos1_vote_mmnoc_mmu_tbu_sf_gdsc = {
@@ -3303,6 +3309,7 @@ static struct gdsc hlos1_vote_mmnoc_mmu_tbu_sf_gdsc = {
 		.name = "hlos1_vote_mmnoc_mmu_tbu_sf_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.flags = VOTABLE,
 };
 
 static struct clk_regmap *gcc_sdm845_clocks[] = {
-- 
2.20.1

[PATCH AUTOSEL 5.4 028/107] clk: mmp2: Fix the order of timer mux parents

[Sasha Levin]

From: Lubomir Rintel <lkundrak@v3.sk>

[ Upstream commit 8bea5ac0fbc5b2103f8779ddff216122e3c2e1ad ]

Determined empirically, no documentation is available.

The OLPC XO-1.75 laptop used parent 1, that one being VCTCXO/4 (65MHz), but
thought it's a VCTCXO/2 (130MHz). The mmp2 timer driver, not knowing
what is going on, ended up just dividing the rate as of
commit f36797ee4380 ("ARM: mmp/mmp2: dt: enable the clock")'

Link: https://lore.kernel.org/r/20191218190454.420358-3-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/mmp/clk-of-mmp2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/mmp/clk-of-mmp2.c b/drivers/clk/mmp/clk-of-mmp2.c
index a60a1be937ad6..b4a95cbbda989 100644
--- a/drivers/clk/mmp/clk-of-mmp2.c
+++ b/drivers/clk/mmp/clk-of-mmp2.c
@@ -134,7 +134,7 @@ static DEFINE_SPINLOCK(ssp3_lock);
 static const char *ssp_parent_names[] = {"vctcxo_4", "vctcxo_2", "vctcxo", "pll1_16"};
 
 static DEFINE_SPINLOCK(timer_lock);
-static const char *timer_parent_names[] = {"clk32", "vctcxo_2", "vctcxo_4", "vctcxo"};
+static const char *timer_parent_names[] = {"clk32", "vctcxo_4", "vctcxo_2", "vctcxo"};
 
 static DEFINE_SPINLOCK(reset_lock);
 
-- 
2.20.1

Re: [PATCH AUTOSEL 5.4 028/107] clk: mmp2: Fix the order of timer mux parents

[Lubomir Rintel]

On Fri, Jan 24, 2020 at 09:16:58AM -0500, Sasha Levin wrote:
> From: Lubomir Rintel <lkundrak@v3.sk>
> 
> [ Upstream commit 8bea5ac0fbc5b2103f8779ddff216122e3c2e1ad ]
> 
> Determined empirically, no documentation is available.
> 
> The OLPC XO-1.75 laptop used parent 1, that one being VCTCXO/4 (65MHz), but
> thought it's a VCTCXO/2 (130MHz). The mmp2 timer driver, not knowing
> what is going on, ended up just dividing the rate as of
> commit f36797ee4380 ("ARM: mmp/mmp2: dt: enable the clock")'

Hi,

this has to go together with this one (in other stable trees too):

  commit 0bd0f30bbf060891f58866a46083a9931f71787c
  Author: Lubomir Rintel <lkundrak@v3.sk>
  Date:   Wed Dec 18 20:04:53 2019 +0100
  
      ARM: mmp: do not divide the clock rate
      
      This was done because the clock driver returned the wrong rate, which is
      fixed in "clk: mmp2: Fix the order of timer mux parents" patch.

It removes a workaround for the same issue from before it was
understood what is going on. If it stays, the clock will run twice as
fast.

Thanks
Lubo

> 
> Link: https://lore.kernel.org/r/20191218190454.420358-3-lkundrak@v3.sk
> Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
> Acked-by: Stephen Boyd <sboyd@kernel.org>
> Signed-off-by: Olof Johansson <olof@lixom.net>
> Signed-off-by: Sasha Levin <sashal@kernel.org>
> ---
>  drivers/clk/mmp/clk-of-mmp2.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/drivers/clk/mmp/clk-of-mmp2.c b/drivers/clk/mmp/clk-of-mmp2.c
> index a60a1be937ad6..b4a95cbbda989 100644
> --- a/drivers/clk/mmp/clk-of-mmp2.c
> +++ b/drivers/clk/mmp/clk-of-mmp2.c
> @@ -134,7 +134,7 @@ static DEFINE_SPINLOCK(ssp3_lock);
>  static const char *ssp_parent_names[] = {"vctcxo_4", "vctcxo_2", "vctcxo", "pll1_16"};
>  
>  static DEFINE_SPINLOCK(timer_lock);
> -static const char *timer_parent_names[] = {"clk32", "vctcxo_2", "vctcxo_4", "vctcxo"};
> +static const char *timer_parent_names[] = {"clk32", "vctcxo_4", "vctcxo_2", "vctcxo"};
>  
>  static DEFINE_SPINLOCK(reset_lock);
>  
> -- 
> 2.20.1
> 

[PATCH AUTOSEL 5.4 029/107] ASoC: rt5640: Fix NULL dereference on module unload

[Sasha Levin]

From: Dmitry Osipenko <digetx@gmail.com>

[ Upstream commit 89b71b3f02d8ae5a08a1dd6f4a2098b7b868d498 ]

The rt5640->jack is NULL if jack is already disabled at the time of
driver's module unloading.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106014707.11378-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/rt5640.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/sound/soc/codecs/rt5640.c b/sound/soc/codecs/rt5640.c
index adbae1f36a8af..747ca248bf10c 100644
--- a/sound/soc/codecs/rt5640.c
+++ b/sound/soc/codecs/rt5640.c
@@ -2432,6 +2432,13 @@ static void rt5640_disable_jack_detect(struct snd_soc_component *component)
 {
 	struct rt5640_priv *rt5640 = snd_soc_component_get_drvdata(component);
 
+	/*
+	 * soc_remove_component() force-disables jack and thus rt5640->jack
+	 * could be NULL at the time of driver's module unloading.
+	 */
+	if (!rt5640->jack)
+		return;
+
 	disable_irq(rt5640->irq);
 	rt5640_cancel_work(rt5640);
 
-- 
2.20.1

[alsa-devel] [PATCH AUTOSEL 5.4 029/107] ASoC: rt5640: Fix NULL dereference on module unload

[Sasha Levin]

From: Dmitry Osipenko <digetx@gmail.com>

[ Upstream commit 89b71b3f02d8ae5a08a1dd6f4a2098b7b868d498 ]

The rt5640->jack is NULL if jack is already disabled at the time of
driver's module unloading.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106014707.11378-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/rt5640.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/sound/soc/codecs/rt5640.c b/sound/soc/codecs/rt5640.c
index adbae1f36a8af..747ca248bf10c 100644
--- a/sound/soc/codecs/rt5640.c
+++ b/sound/soc/codecs/rt5640.c
@@ -2432,6 +2432,13 @@ static void rt5640_disable_jack_detect(struct snd_soc_component *component)
 {
 	struct rt5640_priv *rt5640 = snd_soc_component_get_drvdata(component);
 
+	/*
+	 * soc_remove_component() force-disables jack and thus rt5640->jack
+	 * could be NULL at the time of driver's module unloading.
+	 */
+	if (!rt5640->jack)
+		return;
+
 	disable_irq(rt5640->irq);
 	rt5640_cancel_work(rt5640);
 
-- 
2.20.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel

[PATCH AUTOSEL 5.4 030/107] ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL

[Sasha Levin]

From: Jagan Teki <jagan@amarulasolutions.com>

[ Upstream commit 4a132f60808ae3a751e107a373f8572012352d3c ]

The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.

With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver

While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY

Similar fix has merged for i.Core MX6Q but missed to update for DL.

Fixes: a8039f2dd089 ("ARM: dts: imx6dl: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6dl-icore-mipi.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl-icore-mipi.dts b/arch/arm/boot/dts/imx6dl-icore-mipi.dts
index e43bccb78ab2b..d8f3821a0ffdc 100644
--- a/arch/arm/boot/dts/imx6dl-icore-mipi.dts
+++ b/arch/arm/boot/dts/imx6dl-icore-mipi.dts
@@ -8,7 +8,7 @@
 /dts-v1/;
 
 #include "imx6dl.dtsi"
-#include "imx6qdl-icore.dtsi"
+#include "imx6qdl-icore-1.5.dtsi"
 
 / {
 	model = "Engicam i.CoreM6 DualLite/Solo MIPI Starter Kit";
-- 
2.20.1

[PATCH AUTOSEL 5.4 030/107] ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL

[Sasha Levin]

From: Jagan Teki <jagan@amarulasolutions.com>

[ Upstream commit 4a132f60808ae3a751e107a373f8572012352d3c ]

The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.

With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver

While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY

Similar fix has merged for i.Core MX6Q but missed to update for DL.

Fixes: a8039f2dd089 ("ARM: dts: imx6dl: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6dl-icore-mipi.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6dl-icore-mipi.dts b/arch/arm/boot/dts/imx6dl-icore-mipi.dts
index e43bccb78ab2b..d8f3821a0ffdc 100644
--- a/arch/arm/boot/dts/imx6dl-icore-mipi.dts
+++ b/arch/arm/boot/dts/imx6dl-icore-mipi.dts
@@ -8,7 +8,7 @@
 /dts-v1/;
 
 #include "imx6dl.dtsi"
-#include "imx6qdl-icore.dtsi"
+#include "imx6qdl-icore-1.5.dtsi"
 
 / {
 	model = "Engicam i.CoreM6 DualLite/Solo MIPI Starter Kit";
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 031/107] ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment

[Sasha Levin]

From: Anson Huang <Anson.Huang@nxp.com>

[ Upstream commit 4521de30fbb3f5be0db58de93582ebce72c9d44f ]

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 93385546ba36 ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 71ca76a5e4a51..fe59dde41b649 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -749,10 +749,6 @@
 	vin-supply = <&vgen5_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&vgen5_reg>;
 };
-- 
2.20.1

[PATCH AUTOSEL 5.4 031/107] ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment

[Sasha Levin]

From: Anson Huang <Anson.Huang@nxp.com>

[ Upstream commit 4521de30fbb3f5be0db58de93582ebce72c9d44f ]

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 93385546ba36 ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 71ca76a5e4a51..fe59dde41b649 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -749,10 +749,6 @@
 	vin-supply = <&vgen5_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&vgen5_reg>;
 };
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 032/107] ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment

[Sasha Levin]

From: Anson Huang <Anson.Huang@nxp.com>

[ Upstream commit d4918ebb5c256d26696a13e78ac68c146111191a ]

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 37a4bdead109 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sx-sdb-reva.dts | 4 ----
 arch/arm/boot/dts/imx6sx-sdb.dts      | 4 ----
 2 files changed, 8 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sx-sdb-reva.dts b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
index f1830ed387a55..91a7548fdb8db 100644
--- a/arch/arm/boot/dts/imx6sx-sdb-reva.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
@@ -159,10 +159,6 @@
 	vin-supply = <&vgen6_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&vgen6_reg>;
 };
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts
index a8ee7087af5a5..5a63ca6157229 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb.dts
@@ -141,10 +141,6 @@
 	vin-supply = <&vgen6_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&vgen6_reg>;
 };
-- 
2.20.1

[PATCH AUTOSEL 5.4 032/107] ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment

[Sasha Levin]

From: Anson Huang <Anson.Huang@nxp.com>

[ Upstream commit d4918ebb5c256d26696a13e78ac68c146111191a ]

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 37a4bdead109 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sx-sdb-reva.dts | 4 ----
 arch/arm/boot/dts/imx6sx-sdb.dts      | 4 ----
 2 files changed, 8 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sx-sdb-reva.dts b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
index f1830ed387a55..91a7548fdb8db 100644
--- a/arch/arm/boot/dts/imx6sx-sdb-reva.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
@@ -159,10 +159,6 @@
 	vin-supply = <&vgen6_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&vgen6_reg>;
 };
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts
index a8ee7087af5a5..5a63ca6157229 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb.dts
@@ -141,10 +141,6 @@
 	vin-supply = <&vgen6_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&vgen6_reg>;
 };
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 033/107] ARM: dts: imx6sl-evk: Remove incorrect power supply assignment

[Sasha Levin]

From: Anson Huang <Anson.Huang@nxp.com>

[ Upstream commit b4eb9ef0e29cd28c6fd684e0ab77bda824acb20e ]

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 3feea8805d6f ("ARM: dts: imx6sl-evk: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sl-evk.dts | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index 4829aa682aeb0..bc86cfaaa9c27 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -584,10 +584,6 @@
 	vin-supply = <&sw2_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&sw2_reg>;
 };
-- 
2.20.1

[PATCH AUTOSEL 5.4 033/107] ARM: dts: imx6sl-evk: Remove incorrect power supply assignment

[Sasha Levin]

From: Anson Huang <Anson.Huang@nxp.com>

[ Upstream commit b4eb9ef0e29cd28c6fd684e0ab77bda824acb20e ]

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 3feea8805d6f ("ARM: dts: imx6sl-evk: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sl-evk.dts | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index 4829aa682aeb0..bc86cfaaa9c27 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -584,10 +584,6 @@
 	vin-supply = <&sw2_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&sw2_reg>;
 };
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 034/107] ARM: dts: imx6sll-evk: Remove incorrect power supply assignment

[Sasha Levin]

From: Anson Huang <Anson.Huang@nxp.com>

[ Upstream commit 3479b2843c78ffb60247f522226ba68f93aee355 ]

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 96a9169cf621 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sll-evk.dts | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts
index 3e1d32fdf4b85..5ace9e6acf85c 100644
--- a/arch/arm/boot/dts/imx6sll-evk.dts
+++ b/arch/arm/boot/dts/imx6sll-evk.dts
@@ -265,10 +265,6 @@
 	status = "okay";
 };
 
-&reg_3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &snvs_poweroff {
 	status = "okay";
 };
-- 
2.20.1

[PATCH AUTOSEL 5.4 034/107] ARM: dts: imx6sll-evk: Remove incorrect power supply assignment

[Sasha Levin]

From: Anson Huang <Anson.Huang@nxp.com>

[ Upstream commit 3479b2843c78ffb60247f522226ba68f93aee355 ]

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 96a9169cf621 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sll-evk.dts | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts
index 3e1d32fdf4b85..5ace9e6acf85c 100644
--- a/arch/arm/boot/dts/imx6sll-evk.dts
+++ b/arch/arm/boot/dts/imx6sll-evk.dts
@@ -265,10 +265,6 @@
 	status = "okay";
 };
 
-&reg_3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &snvs_poweroff {
 	status = "okay";
 };
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 035/107] ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support

[Sasha Levin]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

[ Upstream commit 4b0b97e651ecf29f20248420b52b6864fbd40bc2 ]

Turns out when introducing the eMMC version the gpmi node required for
NAND flash support got enabled exclusively on Colibri iMX7D 512MB.

Fixes: f928a4a377e4 ("ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx7s-colibri.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/imx7s-colibri.dtsi b/arch/arm/boot/dts/imx7s-colibri.dtsi
index 1fb1ec5d3d707..6d16e32aed899 100644
--- a/arch/arm/boot/dts/imx7s-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7s-colibri.dtsi
@@ -49,3 +49,7 @@
 		reg = <0x80000000 0x10000000>;
 	};
 };
+
+&gpmi {
+	status = "okay";
+};
-- 
2.20.1

[PATCH AUTOSEL 5.4 035/107] ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support

[Sasha Levin]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

[ Upstream commit 4b0b97e651ecf29f20248420b52b6864fbd40bc2 ]

Turns out when introducing the eMMC version the gpmi node required for
NAND flash support got enabled exclusively on Colibri iMX7D 512MB.

Fixes: f928a4a377e4 ("ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx7s-colibri.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/imx7s-colibri.dtsi b/arch/arm/boot/dts/imx7s-colibri.dtsi
index 1fb1ec5d3d707..6d16e32aed899 100644
--- a/arch/arm/boot/dts/imx7s-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7s-colibri.dtsi
@@ -49,3 +49,7 @@
 		reg = <0x80000000 0x10000000>;
 	};
 };
+
+&gpmi {
+	status = "okay";
+};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.4 036/107] s390/zcrypt: move ap device reset from bus to driver code

[Sasha Levin]

From: Harald Freudenberger <freude@linux.ibm.com>

[ Upstream commit 0c874cd04292c7ee22d70eefc341fa2648f41f46 ]

This patch moves the reset invocation of an ap device when
fresh detected from the ap bus to the probe() function of
the driver responsible for this device.

The virtualisation of ap devices makes it necessary to
remove unconditioned resets on fresh appearing apqn devices.
It may be that such a device is already enabled for guest
usage. So there may be a race condition between host ap bus
and guest ap bus doing the reset. This patch moves the
reset from the ap bus to the zcrypt drivers. So if there
is no zcrypt driver bound to an ap device - for example
the ap device is bound to the vfio device driver - the
ap device is untouched passed to the vfio device driver.

Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/s390/crypto/ap_bus.c       | 2 --
 drivers/s390/crypto/ap_bus.h       | 2 +-
 drivers/s390/crypto/ap_queue.c     | 5 +++--
 drivers/s390/crypto/zcrypt_cex2a.c | 1 +
 drivers/s390/crypto/zcrypt_cex2c.c | 2 ++
 drivers/s390/crypto/zcrypt_cex4.c  | 1 +
 6 files changed, 8 insertions(+), 5 deletions(-)

diff --git a/drivers/s390/crypto/ap_bus.c b/drivers/s390/crypto/ap_bus.c
index a1915061932eb..5256e3ce84e56 100644
--- a/drivers/s390/crypto/ap_bus.c
+++ b/drivers/s390/crypto/ap_bus.c
@@ -793,8 +793,6 @@ static int ap_device_probe(struct device *dev)
 		drvres = ap_drv->flags & AP_DRIVER_FLAG_DEFAULT;
 		if (!!devres != !!drvres)
 			return -ENODEV;
-		/* (re-)init queue's state machine */
-		ap_queue_reinit_state(to_ap_queue(dev));
 	}
 
 	/* Add queue/card to list of active queues/cards */
diff --git a/drivers/s390/crypto/ap_bus.h b/drivers/s390/crypto/ap_bus.h
index 433b7b64368d6..bb35ba4a8d243 100644
--- a/drivers/s390/crypto/ap_bus.h
+++ b/drivers/s390/crypto/ap_bus.h
@@ -261,7 +261,7 @@ void ap_queue_prepare_remove(struct ap_queue *aq);
 void ap_queue_remove(struct ap_queue *aq);
 void ap_queue_suspend(struct ap_device *ap_dev);
 void ap_queue_resume(struct ap_device *ap_dev);
-void ap_queue_reinit_state(struct ap_queue *aq);
+void ap_queue_init_state(struct ap_queue *aq);
 
 struct ap_card *ap_card_create(int id, int queue_depth, int raw_device_type,
 			       int comp_device_type, unsigned int functions);
diff --git a/drivers/s390/crypto/ap_queue.c b/drivers/s390/crypto/ap_queue.c
index dad2be333d826..37c3bdc3642dc 100644
--- a/drivers/s390/crypto/ap_queue.c
+++ b/drivers/s390/crypto/ap_queue.c
@@ -638,7 +638,7 @@ struct ap_queue *ap_queue_create(ap_qid_t qid, int device_type)
 	aq->ap_dev.device.type = &ap_queue_type;
 	aq->ap_dev.device_type = device_type;
 	aq->qid = qid;
-	aq->state = AP_STATE_RESET_START;
+	aq->state = AP_STATE_UNBOUND;
 	aq->interrupt = AP_INTR_DISABLED;
 	spin_lock_init(&aq->lock);
 	INIT_LIST_HEAD(&aq->list);
@@ -771,10 +771,11 @@ void ap_queue_remove(struct ap_queue *aq)
 	spin_unlock_bh(&aq->lock);
 }
 
-void ap_queue_reinit_state(struct ap_queue *aq)
+void ap_queue_init_state(struct ap_queue *aq)
 {
 	spin_lock_bh(&aq->lock);
 	aq->state = AP_STATE_RESET_START;
 	ap_wait(ap_sm_event(aq, AP_EVENT_POLL));
 	spin_unlock_bh(&aq->lock);
 }
+EXPORT_SYMBOL(ap_queue_init_state);
diff --git a/drivers/s390/crypto/zcrypt_cex2a.c b/drivers/s390/crypto/zcrypt_cex2a.c
index c50f3e86cc748..7cbb384ec5352 100644
--- a/drivers/s390/crypto/zcrypt_cex2a.c
+++ b/drivers/s390/crypto/zcrypt_cex2a.c
@@ -175,6 +175,7 @@ static int zcrypt_cex2a_queue_probe(struct ap_device *ap_dev)
 	zq->queue = aq;
 	zq->online = 1;
 	atomic_set(&zq->load, 0);
+	ap_queue_init_state(aq);
 	ap_queue_init_reply(aq, &zq->reply);
 	aq->request_timeout = CEX2A_CLEANUP_TIME,
 	aq->private = zq;
diff --git a/drivers/s390/crypto/zcrypt_cex2c.c b/drivers/s390/crypto/zcrypt_cex2c.c
index 35c7c6672713b..c78c0d119806f 100644
--- a/drivers/s390/crypto/zcrypt_cex2c.c
+++ b/drivers/s390/crypto/zcrypt_cex2c.c
@@ -220,6 +220,7 @@ static int zcrypt_cex2c_queue_probe(struct ap_device *ap_dev)
 	zq->queue = aq;
 	zq->online = 1;
 	atomic_set(&zq->load, 0);
+	ap_rapq(aq->qid);
 	rc = zcrypt_cex2c_rng_supported(aq);
 	if (rc < 0) {
 		zcrypt_queue_free(zq);
@@ -231,6 +232,7 @@ static int zcrypt_cex2c_queue_probe(struct ap_device *ap_dev)
 	else
 		zq->ops = zcrypt_msgtype(MSGTYPE06_NAME,
 					 MSGTYPE06_VARIANT_NORNG);
+	ap_queue_init_state(aq);
 	ap_queue_init_reply(aq, &zq->reply);
 	aq->request_timeout = CEX2C_CLEANUP_TIME;
 	aq->private = zq;
diff --git a/drivers/s390/crypto/zcrypt_cex4.c b/drivers/s390/crypto/zcrypt_cex4.c
index 442e3d6162f76..6fabc906114c0 100644
--- a/drivers/s390/crypto/zcrypt_cex4.c
+++ b/drivers/s390/crypto/zcrypt_cex4.c
@@ -381,6 +381,7 @@ static int zcrypt_cex4_queue_probe(struct ap_device *ap_dev)
 	zq->queue = aq;
 	zq->online = 1;
 	atomic_set(&zq->load, 0);
+	ap_queue_init_state(aq);
 	ap_queue_init_reply(aq, &zq->reply);
 	aq->request_timeout = CEX4_CLEANUP_TIME,
 	aq->private = zq;
-- 
2.20.1

[PATCH AUTOSEL 5.4 037/107] s390/setup: Fix secure ipl message

[Sasha Levin]

From: Philipp Rudo <prudo@linux.ibm.com>

[ Upstream commit 40260b01d029ba374637838213af500e03305326 ]

The new machine loader on z15 always creates an IPL Report block and
thus sets the IPL_PL_FLAG_IPLSR even when secure boot is disabled. This
causes the wrong message being printed at boot. Fix this by checking for
IPL_PL_FLAG_SIPL instead.

Fixes: 9641b8cc733f ("s390/ipl: read IPL report at early boot")
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/s390/kernel/setup.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/s390/kernel/setup.c b/arch/s390/kernel/setup.c
index 3ff291bc63b7e..b95e6fa34cc8e 100644
--- a/arch/s390/kernel/setup.c
+++ b/arch/s390/kernel/setup.c
@@ -1059,7 +1059,7 @@ static void __init log_component_list(void)
 
 	if (!early_ipl_comp_list_addr)
 		return;
-	if (ipl_block.hdr.flags & IPL_PL_FLAG_IPLSR)
+	if (ipl_block.hdr.flags & IPL_PL_FLAG_SIPL)
 		pr_info("Linux is running with Secure-IPL enabled\n");
 	else
 		pr_info("Linux is running with Secure-IPL disabled\n");
-- 
2.20.1

[PATCH AUTOSEL 5.4 038/107] i40e: Fix virtchnl_queue_select bitmap validation

[Sasha Levin]

From: Brett Creeley <brett.creeley@intel.com>

[ Upstream commit d9d6a9aed3f66f8ce5fa3ca6ca26007d75032296 ]

Currently in i40e_vc_disable_queues_msg() we are incorrectly
validating the virtchnl queue select bitmaps. The
virtchnl_queue_select rx_queues and tx_queue bitmap is being
compared against ICE_MAX_VF_QUEUES, but the problem is that
these bitmaps can have a value greater than I40E_MAX_VF_QUEUES.
Fix this by comparing the bitmaps against BIT(I40E_MAX_VF_QUEUES).

Also, add the function i40e_vc_validate_vqs_bitmaps() that checks to see
if both virtchnl_queue_select bitmaps are empty along with checking that
the bitmaps only have valid bits set. This function can then be used in
both the queue enable and disable flows.

Suggested-by: Arkady Gilinksky <arkady.gilinsky@harmonicinc.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../ethernet/intel/i40e/i40e_virtchnl_pf.c    | 22 +++++++++++++++----
 1 file changed, 18 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c b/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
index 3d24408388226..3515ace0f0201 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
@@ -2322,6 +2322,22 @@ static int i40e_ctrl_vf_rx_rings(struct i40e_vsi *vsi, unsigned long q_map,
 	return ret;
 }
 
+/**
+ * i40e_vc_validate_vqs_bitmaps - validate Rx/Tx queue bitmaps from VIRTHCHNL
+ * @vqs: virtchnl_queue_select structure containing bitmaps to validate
+ *
+ * Returns true if validation was successful, else false.
+ */
+static bool i40e_vc_validate_vqs_bitmaps(struct virtchnl_queue_select *vqs)
+{
+	if ((!vqs->rx_queues && !vqs->tx_queues) ||
+	    vqs->rx_queues >= BIT(I40E_MAX_VF_QUEUES) ||
+	    vqs->tx_queues >= BIT(I40E_MAX_VF_QUEUES))
+		return false;
+
+	return true;
+}
+
 /**
  * i40e_vc_enable_queues_msg
  * @vf: pointer to the VF info
@@ -2347,7 +2363,7 @@ static int i40e_vc_enable_queues_msg(struct i40e_vf *vf, u8 *msg)
 		goto error_param;
 	}
 
-	if ((0 == vqs->rx_queues) && (0 == vqs->tx_queues)) {
+	if (i40e_vc_validate_vqs_bitmaps(vqs)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto error_param;
 	}
@@ -2409,9 +2425,7 @@ static int i40e_vc_disable_queues_msg(struct i40e_vf *vf, u8 *msg)
 		goto error_param;
 	}
 
-	if ((vqs->rx_queues == 0 && vqs->tx_queues == 0) ||
-	    vqs->rx_queues > I40E_MAX_VF_QUEUES ||
-	    vqs->tx_queues > I40E_MAX_VF_QUEUES) {
+	if (i40e_vc_validate_vqs_bitmaps(vqs)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto error_param;
 	}
-- 
2.20.1

[Intel-wired-lan] [PATCH AUTOSEL 5.4 038/107] i40e: Fix virtchnl_queue_select bitmap validation

[Sasha Levin]

From: Brett Creeley <brett.creeley@intel.com>

[ Upstream commit d9d6a9aed3f66f8ce5fa3ca6ca26007d75032296 ]

Currently in i40e_vc_disable_queues_msg() we are incorrectly
validating the virtchnl queue select bitmaps. The
virtchnl_queue_select rx_queues and tx_queue bitmap is being
compared against ICE_MAX_VF_QUEUES, but the problem is that
these bitmaps can have a value greater than I40E_MAX_VF_QUEUES.
Fix this by comparing the bitmaps against BIT(I40E_MAX_VF_QUEUES).

Also, add the function i40e_vc_validate_vqs_bitmaps() that checks to see
if both virtchnl_queue_select bitmaps are empty along with checking that
the bitmaps only have valid bits set. This function can then be used in
both the queue enable and disable flows.

Suggested-by: Arkady Gilinksky <arkady.gilinsky@harmonicinc.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../ethernet/intel/i40e/i40e_virtchnl_pf.c    | 22 +++++++++++++++----
 1 file changed, 18 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c b/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
index 3d24408388226..3515ace0f0201 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
@@ -2322,6 +2322,22 @@ static int i40e_ctrl_vf_rx_rings(struct i40e_vsi *vsi, unsigned long q_map,
 	return ret;
 }
 
+/**
+ * i40e_vc_validate_vqs_bitmaps - validate Rx/Tx queue bitmaps from VIRTHCHNL
+ * @vqs: virtchnl_queue_select structure containing bitmaps to validate
+ *
+ * Returns true if validation was successful, else false.
+ */
+static bool i40e_vc_validate_vqs_bitmaps(struct virtchnl_queue_select *vqs)
+{
+	if ((!vqs->rx_queues && !vqs->tx_queues) ||
+	    vqs->rx_queues >= BIT(I40E_MAX_VF_QUEUES) ||
+	    vqs->tx_queues >= BIT(I40E_MAX_VF_QUEUES))
+		return false;
+
+	return true;
+}
+
 /**
  * i40e_vc_enable_queues_msg
  * @vf: pointer to the VF info
@@ -2347,7 +2363,7 @@ static int i40e_vc_enable_queues_msg(struct i40e_vf *vf, u8 *msg)
 		goto error_param;
 	}
 
-	if ((0 == vqs->rx_queues) && (0 == vqs->tx_queues)) {
+	if (i40e_vc_validate_vqs_bitmaps(vqs)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto error_param;
 	}
@@ -2409,9 +2425,7 @@ static int i40e_vc_disable_queues_msg(struct i40e_vf *vf, u8 *msg)
 		goto error_param;
 	}
 
-	if ((vqs->rx_queues == 0 && vqs->tx_queues == 0) ||
-	    vqs->rx_queues > I40E_MAX_VF_QUEUES ||
-	    vqs->tx_queues > I40E_MAX_VF_QUEUES) {
+	if (i40e_vc_validate_vqs_bitmaps(vqs)) {
 		aq_ret = I40E_ERR_PARAM;
 		goto error_param;
 	}
-- 
2.20.1

[PATCH AUTOSEL 5.4 039/107] ixgbevf: Remove limit of 10 entries for unicast filter list

[Sasha Levin]

From: Radoslaw Tyl <radoslawx.tyl@intel.com>

[ Upstream commit aa604651d523b1493988d0bf6710339f3ee60272 ]

Currently, though the FDB entry is added to VF, it does not appear in
RAR filters. VF driver only allows to add 10 entries. Attempting to add
another causes an error. This patch removes limitation and allows use of
all free RAR entries for the FDB if needed.

Fixes: 46ec20ff7d ("ixgbevf: Add macvlan support in the set rx mode op")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
index 076f2da36f278..64ec0e7c64b49 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
@@ -2081,11 +2081,6 @@ static int ixgbevf_write_uc_addr_list(struct net_device *netdev)
 	struct ixgbe_hw *hw = &adapter->hw;
 	int count = 0;
 
-	if ((netdev_uc_count(netdev)) > 10) {
-		pr_err("Too many unicast filters - No Space\n");
-		return -ENOSPC;
-	}
-
 	if (!netdev_uc_empty(netdev)) {
 		struct netdev_hw_addr *ha;
 
-- 
2.20.1

[Intel-wired-lan] [PATCH AUTOSEL 5.4 039/107] ixgbevf: Remove limit of 10 entries for unicast filter list

[Sasha Levin]

From: Radoslaw Tyl <radoslawx.tyl@intel.com>

[ Upstream commit aa604651d523b1493988d0bf6710339f3ee60272 ]

Currently, though the FDB entry is added to VF, it does not appear in
RAR filters. VF driver only allows to add 10 entries. Attempting to add
another causes an error. This patch removes limitation and allows use of
all free RAR entries for the FDB if needed.

Fixes: 46ec20ff7d ("ixgbevf: Add macvlan support in the set rx mode op")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
index 076f2da36f278..64ec0e7c64b49 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
@@ -2081,11 +2081,6 @@ static int ixgbevf_write_uc_addr_list(struct net_device *netdev)
 	struct ixgbe_hw *hw = &adapter->hw;
 	int count = 0;
 
-	if ((netdev_uc_count(netdev)) > 10) {
-		pr_err("Too many unicast filters - No Space\n");
-		return -ENOSPC;
-	}
-
 	if (!netdev_uc_empty(netdev)) {
 		struct netdev_hw_addr *ha;
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 040/107] ixgbe: Fix calculation of queue with VFs and flow director on interface flap

[Sasha Levin]

From: Cambda Zhu <cambda@linux.alibaba.com>

[ Upstream commit 4fad78ad6422d9bca62135bbed8b6abc4cbb85b8 ]

This patch fixes the calculation of queue when we restore flow director
filters after resetting adapter. In ixgbe_fdir_filter_restore(), filter's
vf may be zero which makes the queue outside of the rx_ring array.

The calculation is changed to the same as ixgbe_add_ethtool_fdir_entry().

Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 37 ++++++++++++++-----
 1 file changed, 27 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index c6404abf2dd18..a26f9fb95ac0a 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -5239,7 +5239,7 @@ static void ixgbe_fdir_filter_restore(struct ixgbe_adapter *adapter)
 	struct ixgbe_hw *hw = &adapter->hw;
 	struct hlist_node *node2;
 	struct ixgbe_fdir_filter *filter;
-	u64 action;
+	u8 queue;
 
 	spin_lock(&adapter->fdir_perfect_lock);
 
@@ -5248,17 +5248,34 @@ static void ixgbe_fdir_filter_restore(struct ixgbe_adapter *adapter)
 
 	hlist_for_each_entry_safe(filter, node2,
 				  &adapter->fdir_filter_list, fdir_node) {
-		action = filter->action;
-		if (action != IXGBE_FDIR_DROP_QUEUE && action != 0)
-			action =
-			(action >> ETHTOOL_RX_FLOW_SPEC_RING_VF_OFF) - 1;
+		if (filter->action == IXGBE_FDIR_DROP_QUEUE) {
+			queue = IXGBE_FDIR_DROP_QUEUE;
+		} else {
+			u32 ring = ethtool_get_flow_spec_ring(filter->action);
+			u8 vf = ethtool_get_flow_spec_ring_vf(filter->action);
+
+			if (!vf && (ring >= adapter->num_rx_queues)) {
+				e_err(drv, "FDIR restore failed without VF, ring: %u\n",
+				      ring);
+				continue;
+			} else if (vf &&
+				   ((vf > adapter->num_vfs) ||
+				     ring >= adapter->num_rx_queues_per_pool)) {
+				e_err(drv, "FDIR restore failed with VF, vf: %hhu, ring: %u\n",
+				      vf, ring);
+				continue;
+			}
+
+			/* Map the ring onto the absolute queue index */
+			if (!vf)
+				queue = adapter->rx_ring[ring]->reg_idx;
+			else
+				queue = ((vf - 1) *
+					adapter->num_rx_queues_per_pool) + ring;
+		}
 
 		ixgbe_fdir_write_perfect_filter_82599(hw,
-				&filter->filter,
-				filter->sw_idx,
-				(action == IXGBE_FDIR_DROP_QUEUE) ?
-				IXGBE_FDIR_DROP_QUEUE :
-				adapter->rx_ring[action]->reg_idx);
+				&filter->filter, filter->sw_idx, queue);
 	}
 
 	spin_unlock(&adapter->fdir_perfect_lock);
-- 
2.20.1

[Intel-wired-lan] [PATCH AUTOSEL 5.4 040/107] ixgbe: Fix calculation of queue with VFs and flow director on interface flap

[Sasha Levin]

From: Cambda Zhu <cambda@linux.alibaba.com>

[ Upstream commit 4fad78ad6422d9bca62135bbed8b6abc4cbb85b8 ]

This patch fixes the calculation of queue when we restore flow director
filters after resetting adapter. In ixgbe_fdir_filter_restore(), filter's
vf may be zero which makes the queue outside of the rx_ring array.

The calculation is changed to the same as ixgbe_add_ethtool_fdir_entry().

Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 37 ++++++++++++++-----
 1 file changed, 27 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index c6404abf2dd18..a26f9fb95ac0a 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -5239,7 +5239,7 @@ static void ixgbe_fdir_filter_restore(struct ixgbe_adapter *adapter)
 	struct ixgbe_hw *hw = &adapter->hw;
 	struct hlist_node *node2;
 	struct ixgbe_fdir_filter *filter;
-	u64 action;
+	u8 queue;
 
 	spin_lock(&adapter->fdir_perfect_lock);
 
@@ -5248,17 +5248,34 @@ static void ixgbe_fdir_filter_restore(struct ixgbe_adapter *adapter)
 
 	hlist_for_each_entry_safe(filter, node2,
 				  &adapter->fdir_filter_list, fdir_node) {
-		action = filter->action;
-		if (action != IXGBE_FDIR_DROP_QUEUE && action != 0)
-			action =
-			(action >> ETHTOOL_RX_FLOW_SPEC_RING_VF_OFF) - 1;
+		if (filter->action == IXGBE_FDIR_DROP_QUEUE) {
+			queue = IXGBE_FDIR_DROP_QUEUE;
+		} else {
+			u32 ring = ethtool_get_flow_spec_ring(filter->action);
+			u8 vf = ethtool_get_flow_spec_ring_vf(filter->action);
+
+			if (!vf && (ring >= adapter->num_rx_queues)) {
+				e_err(drv, "FDIR restore failed without VF, ring: %u\n",
+				      ring);
+				continue;
+			} else if (vf &&
+				   ((vf > adapter->num_vfs) ||
+				     ring >= adapter->num_rx_queues_per_pool)) {
+				e_err(drv, "FDIR restore failed with VF, vf: %hhu, ring: %u\n",
+				      vf, ring);
+				continue;
+			}
+
+			/* Map the ring onto the absolute queue index */
+			if (!vf)
+				queue = adapter->rx_ring[ring]->reg_idx;
+			else
+				queue = ((vf - 1) *
+					adapter->num_rx_queues_per_pool) + ring;
+		}
 
 		ixgbe_fdir_write_perfect_filter_82599(hw,
-				&filter->filter,
-				filter->sw_idx,
-				(action == IXGBE_FDIR_DROP_QUEUE) ?
-				IXGBE_FDIR_DROP_QUEUE :
-				adapter->rx_ring[action]->reg_idx);
+				&filter->filter, filter->sw_idx, queue);
 	}
 
 	spin_unlock(&adapter->fdir_perfect_lock);
-- 
2.20.1

[PATCH AUTOSEL 5.4 041/107] igb: Fix SGMII SFP module discovery for 100FX/LX.

[Sasha Levin]

From: Manfred Rudigier <manfred.rudigier@omicronenergy.com>

[ Upstream commit 5365ec1aeff5b9f2962a9c9b31d63f9dad7e0e2d ]

Changing the link mode should also be done for 100BaseFX SGMII modules,
otherwise they just don't work when the default link mode in CTRL_EXT
coming from the EEPROM is SERDES.

Additionally 100Base-LX SGMII SFP modules are also supported now, which
was not the case before.

Tested with an i210 using Flexoptix S.1303.2M.G 100FX and
S.1303.10.G 100LX SGMII SFP modules.

Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/igb/e1000_82575.c | 8 ++------
 drivers/net/ethernet/intel/igb/igb_ethtool.c | 2 +-
 2 files changed, 3 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c
index 8a6ef35141292..438b42ce2cd9a 100644
--- a/drivers/net/ethernet/intel/igb/e1000_82575.c
+++ b/drivers/net/ethernet/intel/igb/e1000_82575.c
@@ -530,7 +530,7 @@ static s32 igb_set_sfp_media_type_82575(struct e1000_hw *hw)
 		dev_spec->module_plugged = true;
 		if (eth_flags->e1000_base_lx || eth_flags->e1000_base_sx) {
 			hw->phy.media_type = e1000_media_type_internal_serdes;
-		} else if (eth_flags->e100_base_fx) {
+		} else if (eth_flags->e100_base_fx || eth_flags->e100_base_lx) {
 			dev_spec->sgmii_active = true;
 			hw->phy.media_type = e1000_media_type_internal_serdes;
 		} else if (eth_flags->e1000_base_t) {
@@ -657,14 +657,10 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 			break;
 		}
 
-		/* do not change link mode for 100BaseFX */
-		if (dev_spec->eth_flags.e100_base_fx)
-			break;
-
 		/* change current link mode setting */
 		ctrl_ext &= ~E1000_CTRL_EXT_LINK_MODE_MASK;
 
-		if (hw->phy.media_type == e1000_media_type_copper)
+		if (dev_spec->sgmii_active)
 			ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_SGMII;
 		else
 			ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;
diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index 3182b059bf55c..8959418776f67 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -181,7 +181,7 @@ static int igb_get_link_ksettings(struct net_device *netdev,
 				advertising &= ~ADVERTISED_1000baseKX_Full;
 			}
 		}
-		if (eth_flags->e100_base_fx) {
+		if (eth_flags->e100_base_fx || eth_flags->e100_base_lx) {
 			supported |= SUPPORTED_100baseT_Full;
 			advertising |= ADVERTISED_100baseT_Full;
 		}
-- 
2.20.1

[Intel-wired-lan] [PATCH AUTOSEL 5.4 041/107] igb: Fix SGMII SFP module discovery for 100FX/LX.

[Sasha Levin]

From: Manfred Rudigier <manfred.rudigier@omicronenergy.com>

[ Upstream commit 5365ec1aeff5b9f2962a9c9b31d63f9dad7e0e2d ]

Changing the link mode should also be done for 100BaseFX SGMII modules,
otherwise they just don't work when the default link mode in CTRL_EXT
coming from the EEPROM is SERDES.

Additionally 100Base-LX SGMII SFP modules are also supported now, which
was not the case before.

Tested with an i210 using Flexoptix S.1303.2M.G 100FX and
S.1303.10.G 100LX SGMII SFP modules.

Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/igb/e1000_82575.c | 8 ++------
 drivers/net/ethernet/intel/igb/igb_ethtool.c | 2 +-
 2 files changed, 3 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c
index 8a6ef35141292..438b42ce2cd9a 100644
--- a/drivers/net/ethernet/intel/igb/e1000_82575.c
+++ b/drivers/net/ethernet/intel/igb/e1000_82575.c
@@ -530,7 +530,7 @@ static s32 igb_set_sfp_media_type_82575(struct e1000_hw *hw)
 		dev_spec->module_plugged = true;
 		if (eth_flags->e1000_base_lx || eth_flags->e1000_base_sx) {
 			hw->phy.media_type = e1000_media_type_internal_serdes;
-		} else if (eth_flags->e100_base_fx) {
+		} else if (eth_flags->e100_base_fx || eth_flags->e100_base_lx) {
 			dev_spec->sgmii_active = true;
 			hw->phy.media_type = e1000_media_type_internal_serdes;
 		} else if (eth_flags->e1000_base_t) {
@@ -657,14 +657,10 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 			break;
 		}
 
-		/* do not change link mode for 100BaseFX */
-		if (dev_spec->eth_flags.e100_base_fx)
-			break;
-
 		/* change current link mode setting */
 		ctrl_ext &= ~E1000_CTRL_EXT_LINK_MODE_MASK;
 
-		if (hw->phy.media_type == e1000_media_type_copper)
+		if (dev_spec->sgmii_active)
 			ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_SGMII;
 		else
 			ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;
diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index 3182b059bf55c..8959418776f67 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -181,7 +181,7 @@ static int igb_get_link_ksettings(struct net_device *netdev,
 				advertising &= ~ADVERTISED_1000baseKX_Full;
 			}
 		}
-		if (eth_flags->e100_base_fx) {
+		if (eth_flags->e100_base_fx || eth_flags->e100_base_lx) {
 			supported |= SUPPORTED_100baseT_Full;
 			advertising |= ADVERTISED_100baseT_Full;
 		}
-- 
2.20.1

[PATCH AUTOSEL 5.4 042/107] iavf: remove current MAC address filter on VF reset

[Sasha Levin]

From: Stefan Assmann <sassmann@kpanic.de>

[ Upstream commit 9e05229190380f6b8f702da39aaeb97a0fc80dc3 ]

Currently MAC filters are not altered during a VF reset event. This may
lead to a stale filter when an administratively set MAC is forced by the
PF.

For an administratively set MAC the PF driver deletes the VFs filters,
overwrites the VFs MAC address and triggers a VF reset. However
the VF driver itself is not aware of the filter removal, which is what
the VF reset is for.
The VF reset queues all filters present in the VF driver to be re-added
to the PF filter list (including the filter for the now stale VF MAC
address) and triggers a VIRTCHNL_OP_GET_VF_RESOURCES event, which
provides the new MAC address to the VF.

When this happens i40e will complain and reject the stale MAC filter,
at least in the untrusted VF case.
i40e 0000:08:00.0: Setting MAC 3c:fa:fa:fa:fa:01 on VF 0
iavf 0000:08:02.0: Reset warning received from the PF
iavf 0000:08:02.0: Scheduling reset task
i40e 0000:08:00.0: Bring down and up the VF interface to make this change effective.
i40e 0000:08:00.0: VF attempting to override administratively set MAC address, bring down and up the VF interface to resume normal operation
i40e 0000:08:00.0: VF 0 failed opcode 10, retval: -1
iavf 0000:08:02.0: Failed to add MAC filter, error IAVF_ERR_NVM

To avoid re-adding the stale MAC filter it needs to be removed from the
VF driver's filter list before queuing the existing filters. Then during
the VIRTCHNL_OP_GET_VF_RESOURCES event the correct filter needs to be
added again, at which point the MAC address has been updated.

As a bonus this change makes bringing the VF down and up again
superfluous for the administratively set MAC case.

Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/iavf/iavf.h          |  2 ++
 drivers/net/ethernet/intel/iavf/iavf_main.c     | 17 +++++++++++++----
 drivers/net/ethernet/intel/iavf/iavf_virtchnl.c |  3 +++
 3 files changed, 18 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/iavf/iavf.h b/drivers/net/ethernet/intel/iavf/iavf.h
index 29de3ae96ef22..bd1b1ed323f4f 100644
--- a/drivers/net/ethernet/intel/iavf/iavf.h
+++ b/drivers/net/ethernet/intel/iavf/iavf.h
@@ -415,4 +415,6 @@ void iavf_enable_channels(struct iavf_adapter *adapter);
 void iavf_disable_channels(struct iavf_adapter *adapter);
 void iavf_add_cloud_filter(struct iavf_adapter *adapter);
 void iavf_del_cloud_filter(struct iavf_adapter *adapter);
+struct iavf_mac_filter *iavf_add_filter(struct iavf_adapter *adapter,
+					const u8 *macaddr);
 #endif /* _IAVF_H_ */
diff --git a/drivers/net/ethernet/intel/iavf/iavf_main.c b/drivers/net/ethernet/intel/iavf/iavf_main.c
index 821987da5698a..8e16be960e96b 100644
--- a/drivers/net/ethernet/intel/iavf/iavf_main.c
+++ b/drivers/net/ethernet/intel/iavf/iavf_main.c
@@ -743,9 +743,8 @@ iavf_mac_filter *iavf_find_filter(struct iavf_adapter *adapter,
  *
  * Returns ptr to the filter object or NULL when no memory available.
  **/
-static struct
-iavf_mac_filter *iavf_add_filter(struct iavf_adapter *adapter,
-				 const u8 *macaddr)
+struct iavf_mac_filter *iavf_add_filter(struct iavf_adapter *adapter,
+					const u8 *macaddr)
 {
 	struct iavf_mac_filter *f;
 
@@ -2065,9 +2064,9 @@ static void iavf_reset_task(struct work_struct *work)
 	struct virtchnl_vf_resource *vfres = adapter->vf_res;
 	struct net_device *netdev = adapter->netdev;
 	struct iavf_hw *hw = &adapter->hw;
+	struct iavf_mac_filter *f, *ftmp;
 	struct iavf_vlan_filter *vlf;
 	struct iavf_cloud_filter *cf;
-	struct iavf_mac_filter *f;
 	u32 reg_val;
 	int i = 0, err;
 	bool running;
@@ -2181,6 +2180,16 @@ continue_reset:
 
 	spin_lock_bh(&adapter->mac_vlan_list_lock);
 
+	/* Delete filter for the current MAC address, it could have
+	 * been changed by the PF via administratively set MAC.
+	 * Will be re-added via VIRTCHNL_OP_GET_VF_RESOURCES.
+	 */
+	list_for_each_entry_safe(f, ftmp, &adapter->mac_filter_list, list) {
+		if (ether_addr_equal(f->macaddr, adapter->hw.mac.addr)) {
+			list_del(&f->list);
+			kfree(f);
+		}
+	}
 	/* re-add all MAC filters */
 	list_for_each_entry(f, &adapter->mac_filter_list, list) {
 		f->add = true;
diff --git a/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c b/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
index c46770eba320e..1ab9cb339acb4 100644
--- a/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
+++ b/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
@@ -1359,6 +1359,9 @@ void iavf_virtchnl_completion(struct iavf_adapter *adapter,
 			ether_addr_copy(netdev->perm_addr,
 					adapter->hw.mac.addr);
 		}
+		spin_lock_bh(&adapter->mac_vlan_list_lock);
+		iavf_add_filter(adapter, adapter->hw.mac.addr);
+		spin_unlock_bh(&adapter->mac_vlan_list_lock);
 		iavf_process_config(adapter);
 		}
 		break;
-- 
2.20.1

[Intel-wired-lan] [PATCH AUTOSEL 5.4 042/107] iavf: remove current MAC address filter on VF reset

[Sasha Levin]

From: Stefan Assmann <sassmann@kpanic.de>

[ Upstream commit 9e05229190380f6b8f702da39aaeb97a0fc80dc3 ]

Currently MAC filters are not altered during a VF reset event. This may
lead to a stale filter when an administratively set MAC is forced by the
PF.

For an administratively set MAC the PF driver deletes the VFs filters,
overwrites the VFs MAC address and triggers a VF reset. However
the VF driver itself is not aware of the filter removal, which is what
the VF reset is for.
The VF reset queues all filters present in the VF driver to be re-added
to the PF filter list (including the filter for the now stale VF MAC
address) and triggers a VIRTCHNL_OP_GET_VF_RESOURCES event, which
provides the new MAC address to the VF.

When this happens i40e will complain and reject the stale MAC filter,
at least in the untrusted VF case.
i40e 0000:08:00.0: Setting MAC 3c:fa:fa:fa:fa:01 on VF 0
iavf 0000:08:02.0: Reset warning received from the PF
iavf 0000:08:02.0: Scheduling reset task
i40e 0000:08:00.0: Bring down and up the VF interface to make this change effective.
i40e 0000:08:00.0: VF attempting to override administratively set MAC address, bring down and up the VF interface to resume normal operation
i40e 0000:08:00.0: VF 0 failed opcode 10, retval: -1
iavf 0000:08:02.0: Failed to add MAC filter, error IAVF_ERR_NVM

To avoid re-adding the stale MAC filter it needs to be removed from the
VF driver's filter list before queuing the existing filters. Then during
the VIRTCHNL_OP_GET_VF_RESOURCES event the correct filter needs to be
added again, at which point the MAC address has been updated.

As a bonus this change makes bringing the VF down and up again
superfluous for the administratively set MAC case.

Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/iavf/iavf.h          |  2 ++
 drivers/net/ethernet/intel/iavf/iavf_main.c     | 17 +++++++++++++----
 drivers/net/ethernet/intel/iavf/iavf_virtchnl.c |  3 +++
 3 files changed, 18 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/iavf/iavf.h b/drivers/net/ethernet/intel/iavf/iavf.h
index 29de3ae96ef22..bd1b1ed323f4f 100644
--- a/drivers/net/ethernet/intel/iavf/iavf.h
+++ b/drivers/net/ethernet/intel/iavf/iavf.h
@@ -415,4 +415,6 @@ void iavf_enable_channels(struct iavf_adapter *adapter);
 void iavf_disable_channels(struct iavf_adapter *adapter);
 void iavf_add_cloud_filter(struct iavf_adapter *adapter);
 void iavf_del_cloud_filter(struct iavf_adapter *adapter);
+struct iavf_mac_filter *iavf_add_filter(struct iavf_adapter *adapter,
+					const u8 *macaddr);
 #endif /* _IAVF_H_ */
diff --git a/drivers/net/ethernet/intel/iavf/iavf_main.c b/drivers/net/ethernet/intel/iavf/iavf_main.c
index 821987da5698a..8e16be960e96b 100644
--- a/drivers/net/ethernet/intel/iavf/iavf_main.c
+++ b/drivers/net/ethernet/intel/iavf/iavf_main.c
@@ -743,9 +743,8 @@ iavf_mac_filter *iavf_find_filter(struct iavf_adapter *adapter,
  *
  * Returns ptr to the filter object or NULL when no memory available.
  **/
-static struct
-iavf_mac_filter *iavf_add_filter(struct iavf_adapter *adapter,
-				 const u8 *macaddr)
+struct iavf_mac_filter *iavf_add_filter(struct iavf_adapter *adapter,
+					const u8 *macaddr)
 {
 	struct iavf_mac_filter *f;
 
@@ -2065,9 +2064,9 @@ static void iavf_reset_task(struct work_struct *work)
 	struct virtchnl_vf_resource *vfres = adapter->vf_res;
 	struct net_device *netdev = adapter->netdev;
 	struct iavf_hw *hw = &adapter->hw;
+	struct iavf_mac_filter *f, *ftmp;
 	struct iavf_vlan_filter *vlf;
 	struct iavf_cloud_filter *cf;
-	struct iavf_mac_filter *f;
 	u32 reg_val;
 	int i = 0, err;
 	bool running;
@@ -2181,6 +2180,16 @@ continue_reset:
 
 	spin_lock_bh(&adapter->mac_vlan_list_lock);
 
+	/* Delete filter for the current MAC address, it could have
+	 * been changed by the PF via administratively set MAC.
+	 * Will be re-added via VIRTCHNL_OP_GET_VF_RESOURCES.
+	 */
+	list_for_each_entry_safe(f, ftmp, &adapter->mac_filter_list, list) {
+		if (ether_addr_equal(f->macaddr, adapter->hw.mac.addr)) {
+			list_del(&f->list);
+			kfree(f);
+		}
+	}
 	/* re-add all MAC filters */
 	list_for_each_entry(f, &adapter->mac_filter_list, list) {
 		f->add = true;
diff --git a/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c b/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
index c46770eba320e..1ab9cb339acb4 100644
--- a/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
+++ b/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
@@ -1359,6 +1359,9 @@ void iavf_virtchnl_completion(struct iavf_adapter *adapter,
 			ether_addr_copy(netdev->perm_addr,
 					adapter->hw.mac.addr);
 		}
+		spin_lock_bh(&adapter->mac_vlan_list_lock);
+		iavf_add_filter(adapter, adapter->hw.mac.addr);
+		spin_unlock_bh(&adapter->mac_vlan_list_lock);
 		iavf_process_config(adapter);
 		}
 		break;
-- 
2.20.1

[PATCH AUTOSEL 5.4 043/107] ASoC: stm32: sai: fix possible circular locking

[Sasha Levin]

From: Olivier Moysan <olivier.moysan@st.com>

[ Upstream commit a14bf98c045bf119b7e779f186528e38c6428830 ]

In current driver, locks can be taken as follows:
- Register access: take a lock on regmap config and then on clock.
- Master clock provider: take a lock on clock and then on regmap config.
This can lead to the circular locking summarized below.

Remove peripheral clock management through regmap framework, and manage
peripheral clock in driver instead. On register access, lock on clock
is taken first, which allows to avoid possible locking issue.

[ 6696.561513] ======================================================
[ 6696.567670] WARNING: possible circular locking dependency detected
[ 6696.573842] 4.19.49 #866 Not tainted
[ 6696.577397] ------------------------------------------------------
[ 6696.583566] pulseaudio/6439 is trying to acquire lock:
[ 6696.588697] 87b0a25b (enable_lock){..-.}, at: clk_enable_lock+0x64/0x128
[ 6696.595377]
[ 6696.595377] but task is already holding lock:
[ 6696.601197] d858f825 (stm32_sai_sub:1342:(sai->regmap_config)->lock){....}
...
[ 6696.812513]  Possible unsafe locking scenario:
[ 6696.812513]
[ 6696.818418]        CPU0                    CPU1
[ 6696.822935]        ----                    ----
[ 6696.827451]   lock(stm32_sai_sub:1342:(sai->regmap_config)->lock);
[ 6696.833618]                                lock(enable_lock);
[ 6696.839350]                                lock(stm32_sai_sub:1342:
                                              (sai->regmap_config)->lock);
[ 6696.848035]   lock(enable_lock);

Fixes: 03e78a242a15 ("ASoC: stm32: sai: add h7 support")

Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200109083254.478-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/stm/stm32_sai_sub.c | 194 ++++++++++++++++++++++++----------
 1 file changed, 140 insertions(+), 54 deletions(-)

diff --git a/sound/soc/stm/stm32_sai_sub.c b/sound/soc/stm/stm32_sai_sub.c
index 48e629ac2d88b..30bcd5d3a32a8 100644
--- a/sound/soc/stm/stm32_sai_sub.c
+++ b/sound/soc/stm/stm32_sai_sub.c
@@ -184,6 +184,56 @@ static bool stm32_sai_sub_writeable_reg(struct device *dev, unsigned int reg)
 	}
 }
 
+static int stm32_sai_sub_reg_up(struct stm32_sai_sub_data *sai,
+				unsigned int reg, unsigned int mask,
+				unsigned int val)
+{
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_update_bits(sai->regmap, reg, mask, val);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
+}
+
+static int stm32_sai_sub_reg_wr(struct stm32_sai_sub_data *sai,
+				unsigned int reg, unsigned int mask,
+				unsigned int val)
+{
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_write_bits(sai->regmap, reg, mask, val);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
+}
+
+static int stm32_sai_sub_reg_rd(struct stm32_sai_sub_data *sai,
+				unsigned int reg, unsigned int *val)
+{
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_read(sai->regmap, reg, val);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
+}
+
 static const struct regmap_config stm32_sai_sub_regmap_config_f4 = {
 	.reg_bits = 32,
 	.reg_stride = 4,
@@ -295,7 +345,7 @@ static int stm32_sai_set_clk_div(struct stm32_sai_sub_data *sai,
 
 	mask = SAI_XCR1_MCKDIV_MASK(SAI_XCR1_MCKDIV_WIDTH(version));
 	cr1 = SAI_XCR1_MCKDIV_SET(div);
-	ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, mask, cr1);
+	ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, mask, cr1);
 	if (ret < 0)
 		dev_err(&sai->pdev->dev, "Failed to update CR1 register\n");
 
@@ -372,8 +422,8 @@ static int stm32_sai_mclk_enable(struct clk_hw *hw)
 
 	dev_dbg(&sai->pdev->dev, "Enable master clock\n");
 
-	return regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-				  SAI_XCR1_MCKEN, SAI_XCR1_MCKEN);
+	return stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+				    SAI_XCR1_MCKEN, SAI_XCR1_MCKEN);
 }
 
 static void stm32_sai_mclk_disable(struct clk_hw *hw)
@@ -383,7 +433,7 @@ static void stm32_sai_mclk_disable(struct clk_hw *hw)
 
 	dev_dbg(&sai->pdev->dev, "Disable master clock\n");
 
-	regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, SAI_XCR1_MCKEN, 0);
+	stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, SAI_XCR1_MCKEN, 0);
 }
 
 static const struct clk_ops mclk_ops = {
@@ -446,15 +496,15 @@ static irqreturn_t stm32_sai_isr(int irq, void *devid)
 	unsigned int sr, imr, flags;
 	snd_pcm_state_t status = SNDRV_PCM_STATE_RUNNING;
 
-	regmap_read(sai->regmap, STM_SAI_IMR_REGX, &imr);
-	regmap_read(sai->regmap, STM_SAI_SR_REGX, &sr);
+	stm32_sai_sub_reg_rd(sai, STM_SAI_IMR_REGX, &imr);
+	stm32_sai_sub_reg_rd(sai, STM_SAI_SR_REGX, &sr);
 
 	flags = sr & imr;
 	if (!flags)
 		return IRQ_NONE;
 
-	regmap_write_bits(sai->regmap, STM_SAI_CLRFR_REGX, SAI_XCLRFR_MASK,
-			  SAI_XCLRFR_MASK);
+	stm32_sai_sub_reg_wr(sai, STM_SAI_CLRFR_REGX, SAI_XCLRFR_MASK,
+			     SAI_XCLRFR_MASK);
 
 	if (!sai->substream) {
 		dev_err(&pdev->dev, "Device stopped. Spurious IRQ 0x%x\n", sr);
@@ -503,8 +553,8 @@ static int stm32_sai_set_sysclk(struct snd_soc_dai *cpu_dai,
 	int ret;
 
 	if (dir == SND_SOC_CLOCK_OUT && sai->sai_mclk) {
-		ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-					 SAI_XCR1_NODIV,
+		ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+					   SAI_XCR1_NODIV,
 					 freq ? 0 : SAI_XCR1_NODIV);
 		if (ret < 0)
 			return ret;
@@ -583,7 +633,7 @@ static int stm32_sai_set_dai_tdm_slot(struct snd_soc_dai *cpu_dai, u32 tx_mask,
 
 	slotr_mask |= SAI_XSLOTR_SLOTEN_MASK;
 
-	regmap_update_bits(sai->regmap, STM_SAI_SLOTR_REGX, slotr_mask, slotr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_SLOTR_REGX, slotr_mask, slotr);
 
 	sai->slot_width = slot_width;
 	sai->slots = slots;
@@ -665,7 +715,7 @@ static int stm32_sai_set_dai_fmt(struct snd_soc_dai *cpu_dai, unsigned int fmt)
 	cr1_mask |= SAI_XCR1_CKSTR;
 	frcr_mask |= SAI_XFRCR_FSPOL;
 
-	regmap_update_bits(sai->regmap, STM_SAI_FRCR_REGX, frcr_mask, frcr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_FRCR_REGX, frcr_mask, frcr);
 
 	/* DAI clock master masks */
 	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
@@ -693,7 +743,7 @@ static int stm32_sai_set_dai_fmt(struct snd_soc_dai *cpu_dai, unsigned int fmt)
 	cr1_mask |= SAI_XCR1_SLAVE;
 
 conf_update:
-	ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, cr1_mask, cr1);
+	ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, cr1_mask, cr1);
 	if (ret < 0) {
 		dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 		return ret;
@@ -730,12 +780,12 @@ static int stm32_sai_startup(struct snd_pcm_substream *substream,
 	}
 
 	/* Enable ITs */
-	regmap_write_bits(sai->regmap, STM_SAI_CLRFR_REGX,
-			  SAI_XCLRFR_MASK, SAI_XCLRFR_MASK);
+	stm32_sai_sub_reg_wr(sai, STM_SAI_CLRFR_REGX,
+			     SAI_XCLRFR_MASK, SAI_XCLRFR_MASK);
 
 	imr = SAI_XIMR_OVRUDRIE;
 	if (STM_SAI_IS_CAPTURE(sai)) {
-		regmap_read(sai->regmap, STM_SAI_CR2_REGX, &cr2);
+		stm32_sai_sub_reg_rd(sai, STM_SAI_CR2_REGX, &cr2);
 		if (cr2 & SAI_XCR2_MUTECNT_MASK)
 			imr |= SAI_XIMR_MUTEDETIE;
 	}
@@ -745,8 +795,8 @@ static int stm32_sai_startup(struct snd_pcm_substream *substream,
 	else
 		imr |= SAI_XIMR_AFSDETIE | SAI_XIMR_LFSDETIE;
 
-	regmap_update_bits(sai->regmap, STM_SAI_IMR_REGX,
-			   SAI_XIMR_MASK, imr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_IMR_REGX,
+			     SAI_XIMR_MASK, imr);
 
 	return 0;
 }
@@ -763,10 +813,10 @@ static int stm32_sai_set_config(struct snd_soc_dai *cpu_dai,
 	 * SAI fifo threshold is set to half fifo, to keep enough space
 	 * for DMA incoming bursts.
 	 */
-	regmap_write_bits(sai->regmap, STM_SAI_CR2_REGX,
-			  SAI_XCR2_FFLUSH | SAI_XCR2_FTH_MASK,
-			  SAI_XCR2_FFLUSH |
-			  SAI_XCR2_FTH_SET(STM_SAI_FIFO_TH_HALF));
+	stm32_sai_sub_reg_wr(sai, STM_SAI_CR2_REGX,
+			     SAI_XCR2_FFLUSH | SAI_XCR2_FTH_MASK,
+			     SAI_XCR2_FFLUSH |
+			     SAI_XCR2_FTH_SET(STM_SAI_FIFO_TH_HALF));
 
 	/* DS bits in CR1 not set for SPDIF (size forced to 24 bits).*/
 	if (STM_SAI_PROTOCOL_IS_SPDIF(sai)) {
@@ -795,7 +845,7 @@ static int stm32_sai_set_config(struct snd_soc_dai *cpu_dai,
 	if ((sai->slots == 2) && (params_channels(params) == 1))
 		cr1 |= SAI_XCR1_MONO;
 
-	ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, cr1_mask, cr1);
+	ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, cr1_mask, cr1);
 	if (ret < 0) {
 		dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 		return ret;
@@ -809,7 +859,7 @@ static int stm32_sai_set_slots(struct snd_soc_dai *cpu_dai)
 	struct stm32_sai_sub_data *sai = snd_soc_dai_get_drvdata(cpu_dai);
 	int slotr, slot_sz;
 
-	regmap_read(sai->regmap, STM_SAI_SLOTR_REGX, &slotr);
+	stm32_sai_sub_reg_rd(sai, STM_SAI_SLOTR_REGX, &slotr);
 
 	/*
 	 * If SLOTSZ is set to auto in SLOTR, align slot width on data size
@@ -831,16 +881,16 @@ static int stm32_sai_set_slots(struct snd_soc_dai *cpu_dai)
 		sai->slots = 2;
 
 	/* The number of slots in the audio frame is equal to NBSLOT[3:0] + 1*/
-	regmap_update_bits(sai->regmap, STM_SAI_SLOTR_REGX,
-			   SAI_XSLOTR_NBSLOT_MASK,
-			   SAI_XSLOTR_NBSLOT_SET((sai->slots - 1)));
+	stm32_sai_sub_reg_up(sai, STM_SAI_SLOTR_REGX,
+			     SAI_XSLOTR_NBSLOT_MASK,
+			     SAI_XSLOTR_NBSLOT_SET((sai->slots - 1)));
 
 	/* Set default slots mask if not already set from DT */
 	if (!(slotr & SAI_XSLOTR_SLOTEN_MASK)) {
 		sai->slot_mask = (1 << sai->slots) - 1;
-		regmap_update_bits(sai->regmap,
-				   STM_SAI_SLOTR_REGX, SAI_XSLOTR_SLOTEN_MASK,
-				   SAI_XSLOTR_SLOTEN_SET(sai->slot_mask));
+		stm32_sai_sub_reg_up(sai,
+				     STM_SAI_SLOTR_REGX, SAI_XSLOTR_SLOTEN_MASK,
+				     SAI_XSLOTR_SLOTEN_SET(sai->slot_mask));
 	}
 
 	dev_dbg(cpu_dai->dev, "Slots %d, slot width %d\n",
@@ -870,14 +920,14 @@ static void stm32_sai_set_frame(struct snd_soc_dai *cpu_dai)
 	dev_dbg(cpu_dai->dev, "Frame length %d, frame active %d\n",
 		sai->fs_length, fs_active);
 
-	regmap_update_bits(sai->regmap, STM_SAI_FRCR_REGX, frcr_mask, frcr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_FRCR_REGX, frcr_mask, frcr);
 
 	if ((sai->fmt & SND_SOC_DAIFMT_FORMAT_MASK) == SND_SOC_DAIFMT_LSB) {
 		offset = sai->slot_width - sai->data_size;
 
-		regmap_update_bits(sai->regmap, STM_SAI_SLOTR_REGX,
-				   SAI_XSLOTR_FBOFF_MASK,
-				   SAI_XSLOTR_FBOFF_SET(offset));
+		stm32_sai_sub_reg_up(sai, STM_SAI_SLOTR_REGX,
+				     SAI_XSLOTR_FBOFF_MASK,
+				     SAI_XSLOTR_FBOFF_SET(offset));
 	}
 }
 
@@ -994,9 +1044,9 @@ static int stm32_sai_configure_clock(struct snd_soc_dai *cpu_dai,
 					return -EINVAL;
 				}
 
-				regmap_update_bits(sai->regmap,
-						   STM_SAI_CR1_REGX,
-						   SAI_XCR1_OSR, cr1);
+				stm32_sai_sub_reg_up(sai,
+						     STM_SAI_CR1_REGX,
+						     SAI_XCR1_OSR, cr1);
 
 				div = stm32_sai_get_clk_div(sai, sai_clk_rate,
 							    sai->mclk_rate);
@@ -1058,12 +1108,12 @@ static int stm32_sai_trigger(struct snd_pcm_substream *substream, int cmd,
 	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
 		dev_dbg(cpu_dai->dev, "Enable DMA and SAI\n");
 
-		regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-				   SAI_XCR1_DMAEN, SAI_XCR1_DMAEN);
+		stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+				     SAI_XCR1_DMAEN, SAI_XCR1_DMAEN);
 
 		/* Enable SAI */
-		ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-					 SAI_XCR1_SAIEN, SAI_XCR1_SAIEN);
+		ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+					   SAI_XCR1_SAIEN, SAI_XCR1_SAIEN);
 		if (ret < 0)
 			dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 		break;
@@ -1072,16 +1122,16 @@ static int stm32_sai_trigger(struct snd_pcm_substream *substream, int cmd,
 	case SNDRV_PCM_TRIGGER_STOP:
 		dev_dbg(cpu_dai->dev, "Disable DMA and SAI\n");
 
-		regmap_update_bits(sai->regmap, STM_SAI_IMR_REGX,
-				   SAI_XIMR_MASK, 0);
+		stm32_sai_sub_reg_up(sai, STM_SAI_IMR_REGX,
+				     SAI_XIMR_MASK, 0);
 
-		regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-				   SAI_XCR1_SAIEN,
-				   (unsigned int)~SAI_XCR1_SAIEN);
+		stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+				     SAI_XCR1_SAIEN,
+				     (unsigned int)~SAI_XCR1_SAIEN);
 
-		ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-					 SAI_XCR1_DMAEN,
-					 (unsigned int)~SAI_XCR1_DMAEN);
+		ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+					   SAI_XCR1_DMAEN,
+					   (unsigned int)~SAI_XCR1_DMAEN);
 		if (ret < 0)
 			dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 
@@ -1101,7 +1151,7 @@ static void stm32_sai_shutdown(struct snd_pcm_substream *substream,
 	struct stm32_sai_sub_data *sai = snd_soc_dai_get_drvdata(cpu_dai);
 	unsigned long flags;
 
-	regmap_update_bits(sai->regmap, STM_SAI_IMR_REGX, SAI_XIMR_MASK, 0);
+	stm32_sai_sub_reg_up(sai, STM_SAI_IMR_REGX, SAI_XIMR_MASK, 0);
 
 	clk_disable_unprepare(sai->sai_ck);
 
@@ -1169,7 +1219,7 @@ static int stm32_sai_dai_probe(struct snd_soc_dai *cpu_dai)
 	cr1_mask |= SAI_XCR1_SYNCEN_MASK;
 	cr1 |= SAI_XCR1_SYNCEN_SET(sai->sync);
 
-	return regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, cr1_mask, cr1);
+	return stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, cr1_mask, cr1);
 }
 
 static const struct snd_soc_dai_ops stm32_sai_pcm_dai_ops = {
@@ -1322,8 +1372,13 @@ static int stm32_sai_sub_parse_of(struct platform_device *pdev,
 	if (STM_SAI_HAS_PDM(sai) && STM_SAI_IS_SUB_A(sai))
 		sai->regmap_config = &stm32_sai_sub_regmap_config_h7;
 
-	sai->regmap = devm_regmap_init_mmio_clk(&pdev->dev, "sai_ck",
-						base, sai->regmap_config);
+	/*
+	 * Do not manage peripheral clock through regmap framework as this
+	 * can lead to circular locking issue with sai master clock provider.
+	 * Manage peripheral clock directly in driver instead.
+	 */
+	sai->regmap = devm_regmap_init_mmio(&pdev->dev, base,
+					    sai->regmap_config);
 	if (IS_ERR(sai->regmap)) {
 		dev_err(&pdev->dev, "Failed to initialize MMIO\n");
 		return PTR_ERR(sai->regmap);
@@ -1420,6 +1475,10 @@ static int stm32_sai_sub_parse_of(struct platform_device *pdev,
 		return PTR_ERR(sai->sai_ck);
 	}
 
+	ret = clk_prepare(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
 	if (STM_SAI_IS_F4(sai->pdata))
 		return 0;
 
@@ -1501,22 +1560,48 @@ static int stm32_sai_sub_probe(struct platform_device *pdev)
 	return 0;
 }
 
+static int stm32_sai_sub_remove(struct platform_device *pdev)
+{
+	struct stm32_sai_sub_data *sai = dev_get_drvdata(&pdev->dev);
+
+	clk_unprepare(sai->pdata->pclk);
+
+	return 0;
+}
+
 #ifdef CONFIG_PM_SLEEP
 static int stm32_sai_sub_suspend(struct device *dev)
 {
 	struct stm32_sai_sub_data *sai = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
 
 	regcache_cache_only(sai->regmap, true);
 	regcache_mark_dirty(sai->regmap);
+
+	clk_disable(sai->pdata->pclk);
+
 	return 0;
 }
 
 static int stm32_sai_sub_resume(struct device *dev)
 {
 	struct stm32_sai_sub_data *sai = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
 
 	regcache_cache_only(sai->regmap, false);
-	return regcache_sync(sai->regmap);
+	ret = regcache_sync(sai->regmap);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
 }
 #endif /* CONFIG_PM_SLEEP */
 
@@ -1531,6 +1616,7 @@ static struct platform_driver stm32_sai_sub_driver = {
 		.pm = &stm32_sai_sub_pm_ops,
 	},
 	.probe = stm32_sai_sub_probe,
+	.remove = stm32_sai_sub_remove,
 };
 
 module_platform_driver(stm32_sai_sub_driver);
-- 
2.20.1

[PATCH AUTOSEL 5.4 043/107] ASoC: stm32: sai: fix possible circular locking

[Sasha Levin]

From: Olivier Moysan <olivier.moysan@st.com>

[ Upstream commit a14bf98c045bf119b7e779f186528e38c6428830 ]

In current driver, locks can be taken as follows:
- Register access: take a lock on regmap config and then on clock.
- Master clock provider: take a lock on clock and then on regmap config.
This can lead to the circular locking summarized below.

Remove peripheral clock management through regmap framework, and manage
peripheral clock in driver instead. On register access, lock on clock
is taken first, which allows to avoid possible locking issue.

[ 6696.561513] ======================================================
[ 6696.567670] WARNING: possible circular locking dependency detected
[ 6696.573842] 4.19.49 #866 Not tainted
[ 6696.577397] ------------------------------------------------------
[ 6696.583566] pulseaudio/6439 is trying to acquire lock:
[ 6696.588697] 87b0a25b (enable_lock){..-.}, at: clk_enable_lock+0x64/0x128
[ 6696.595377]
[ 6696.595377] but task is already holding lock:
[ 6696.601197] d858f825 (stm32_sai_sub:1342:(sai->regmap_config)->lock){....}
...
[ 6696.812513]  Possible unsafe locking scenario:
[ 6696.812513]
[ 6696.818418]        CPU0                    CPU1
[ 6696.822935]        ----                    ----
[ 6696.827451]   lock(stm32_sai_sub:1342:(sai->regmap_config)->lock);
[ 6696.833618]                                lock(enable_lock);
[ 6696.839350]                                lock(stm32_sai_sub:1342:
                                              (sai->regmap_config)->lock);
[ 6696.848035]   lock(enable_lock);

Fixes: 03e78a242a15 ("ASoC: stm32: sai: add h7 support")

Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200109083254.478-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/stm/stm32_sai_sub.c | 194 ++++++++++++++++++++++++----------
 1 file changed, 140 insertions(+), 54 deletions(-)

diff --git a/sound/soc/stm/stm32_sai_sub.c b/sound/soc/stm/stm32_sai_sub.c
index 48e629ac2d88b..30bcd5d3a32a8 100644
--- a/sound/soc/stm/stm32_sai_sub.c
+++ b/sound/soc/stm/stm32_sai_sub.c
@@ -184,6 +184,56 @@ static bool stm32_sai_sub_writeable_reg(struct device *dev, unsigned int reg)
 	}
 }
 
+static int stm32_sai_sub_reg_up(struct stm32_sai_sub_data *sai,
+				unsigned int reg, unsigned int mask,
+				unsigned int val)
+{
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_update_bits(sai->regmap, reg, mask, val);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
+}
+
+static int stm32_sai_sub_reg_wr(struct stm32_sai_sub_data *sai,
+				unsigned int reg, unsigned int mask,
+				unsigned int val)
+{
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_write_bits(sai->regmap, reg, mask, val);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
+}
+
+static int stm32_sai_sub_reg_rd(struct stm32_sai_sub_data *sai,
+				unsigned int reg, unsigned int *val)
+{
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_read(sai->regmap, reg, val);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
+}
+
 static const struct regmap_config stm32_sai_sub_regmap_config_f4 = {
 	.reg_bits = 32,
 	.reg_stride = 4,
@@ -295,7 +345,7 @@ static int stm32_sai_set_clk_div(struct stm32_sai_sub_data *sai,
 
 	mask = SAI_XCR1_MCKDIV_MASK(SAI_XCR1_MCKDIV_WIDTH(version));
 	cr1 = SAI_XCR1_MCKDIV_SET(div);
-	ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, mask, cr1);
+	ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, mask, cr1);
 	if (ret < 0)
 		dev_err(&sai->pdev->dev, "Failed to update CR1 register\n");
 
@@ -372,8 +422,8 @@ static int stm32_sai_mclk_enable(struct clk_hw *hw)
 
 	dev_dbg(&sai->pdev->dev, "Enable master clock\n");
 
-	return regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-				  SAI_XCR1_MCKEN, SAI_XCR1_MCKEN);
+	return stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+				    SAI_XCR1_MCKEN, SAI_XCR1_MCKEN);
 }
 
 static void stm32_sai_mclk_disable(struct clk_hw *hw)
@@ -383,7 +433,7 @@ static void stm32_sai_mclk_disable(struct clk_hw *hw)
 
 	dev_dbg(&sai->pdev->dev, "Disable master clock\n");
 
-	regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, SAI_XCR1_MCKEN, 0);
+	stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, SAI_XCR1_MCKEN, 0);
 }
 
 static const struct clk_ops mclk_ops = {
@@ -446,15 +496,15 @@ static irqreturn_t stm32_sai_isr(int irq, void *devid)
 	unsigned int sr, imr, flags;
 	snd_pcm_state_t status = SNDRV_PCM_STATE_RUNNING;
 
-	regmap_read(sai->regmap, STM_SAI_IMR_REGX, &imr);
-	regmap_read(sai->regmap, STM_SAI_SR_REGX, &sr);
+	stm32_sai_sub_reg_rd(sai, STM_SAI_IMR_REGX, &imr);
+	stm32_sai_sub_reg_rd(sai, STM_SAI_SR_REGX, &sr);
 
 	flags = sr & imr;
 	if (!flags)
 		return IRQ_NONE;
 
-	regmap_write_bits(sai->regmap, STM_SAI_CLRFR_REGX, SAI_XCLRFR_MASK,
-			  SAI_XCLRFR_MASK);
+	stm32_sai_sub_reg_wr(sai, STM_SAI_CLRFR_REGX, SAI_XCLRFR_MASK,
+			     SAI_XCLRFR_MASK);
 
 	if (!sai->substream) {
 		dev_err(&pdev->dev, "Device stopped. Spurious IRQ 0x%x\n", sr);
@@ -503,8 +553,8 @@ static int stm32_sai_set_sysclk(struct snd_soc_dai *cpu_dai,
 	int ret;
 
 	if (dir == SND_SOC_CLOCK_OUT && sai->sai_mclk) {
-		ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-					 SAI_XCR1_NODIV,
+		ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+					   SAI_XCR1_NODIV,
 					 freq ? 0 : SAI_XCR1_NODIV);
 		if (ret < 0)
 			return ret;
@@ -583,7 +633,7 @@ static int stm32_sai_set_dai_tdm_slot(struct snd_soc_dai *cpu_dai, u32 tx_mask,
 
 	slotr_mask |= SAI_XSLOTR_SLOTEN_MASK;
 
-	regmap_update_bits(sai->regmap, STM_SAI_SLOTR_REGX, slotr_mask, slotr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_SLOTR_REGX, slotr_mask, slotr);
 
 	sai->slot_width = slot_width;
 	sai->slots = slots;
@@ -665,7 +715,7 @@ static int stm32_sai_set_dai_fmt(struct snd_soc_dai *cpu_dai, unsigned int fmt)
 	cr1_mask |= SAI_XCR1_CKSTR;
 	frcr_mask |= SAI_XFRCR_FSPOL;
 
-	regmap_update_bits(sai->regmap, STM_SAI_FRCR_REGX, frcr_mask, frcr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_FRCR_REGX, frcr_mask, frcr);
 
 	/* DAI clock master masks */
 	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
@@ -693,7 +743,7 @@ static int stm32_sai_set_dai_fmt(struct snd_soc_dai *cpu_dai, unsigned int fmt)
 	cr1_mask |= SAI_XCR1_SLAVE;
 
 conf_update:
-	ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, cr1_mask, cr1);
+	ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, cr1_mask, cr1);
 	if (ret < 0) {
 		dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 		return ret;
@@ -730,12 +780,12 @@ static int stm32_sai_startup(struct snd_pcm_substream *substream,
 	}
 
 	/* Enable ITs */
-	regmap_write_bits(sai->regmap, STM_SAI_CLRFR_REGX,
-			  SAI_XCLRFR_MASK, SAI_XCLRFR_MASK);
+	stm32_sai_sub_reg_wr(sai, STM_SAI_CLRFR_REGX,
+			     SAI_XCLRFR_MASK, SAI_XCLRFR_MASK);
 
 	imr = SAI_XIMR_OVRUDRIE;
 	if (STM_SAI_IS_CAPTURE(sai)) {
-		regmap_read(sai->regmap, STM_SAI_CR2_REGX, &cr2);
+		stm32_sai_sub_reg_rd(sai, STM_SAI_CR2_REGX, &cr2);
 		if (cr2 & SAI_XCR2_MUTECNT_MASK)
 			imr |= SAI_XIMR_MUTEDETIE;
 	}
@@ -745,8 +795,8 @@ static int stm32_sai_startup(struct snd_pcm_substream *substream,
 	else
 		imr |= SAI_XIMR_AFSDETIE | SAI_XIMR_LFSDETIE;
 
-	regmap_update_bits(sai->regmap, STM_SAI_IMR_REGX,
-			   SAI_XIMR_MASK, imr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_IMR_REGX,
+			     SAI_XIMR_MASK, imr);
 
 	return 0;
 }
@@ -763,10 +813,10 @@ static int stm32_sai_set_config(struct snd_soc_dai *cpu_dai,
 	 * SAI fifo threshold is set to half fifo, to keep enough space
 	 * for DMA incoming bursts.
 	 */
-	regmap_write_bits(sai->regmap, STM_SAI_CR2_REGX,
-			  SAI_XCR2_FFLUSH | SAI_XCR2_FTH_MASK,
-			  SAI_XCR2_FFLUSH |
-			  SAI_XCR2_FTH_SET(STM_SAI_FIFO_TH_HALF));
+	stm32_sai_sub_reg_wr(sai, STM_SAI_CR2_REGX,
+			     SAI_XCR2_FFLUSH | SAI_XCR2_FTH_MASK,
+			     SAI_XCR2_FFLUSH |
+			     SAI_XCR2_FTH_SET(STM_SAI_FIFO_TH_HALF));
 
 	/* DS bits in CR1 not set for SPDIF (size forced to 24 bits).*/
 	if (STM_SAI_PROTOCOL_IS_SPDIF(sai)) {
@@ -795,7 +845,7 @@ static int stm32_sai_set_config(struct snd_soc_dai *cpu_dai,
 	if ((sai->slots == 2) && (params_channels(params) == 1))
 		cr1 |= SAI_XCR1_MONO;
 
-	ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, cr1_mask, cr1);
+	ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, cr1_mask, cr1);
 	if (ret < 0) {
 		dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 		return ret;
@@ -809,7 +859,7 @@ static int stm32_sai_set_slots(struct snd_soc_dai *cpu_dai)
 	struct stm32_sai_sub_data *sai = snd_soc_dai_get_drvdata(cpu_dai);
 	int slotr, slot_sz;
 
-	regmap_read(sai->regmap, STM_SAI_SLOTR_REGX, &slotr);
+	stm32_sai_sub_reg_rd(sai, STM_SAI_SLOTR_REGX, &slotr);
 
 	/*
 	 * If SLOTSZ is set to auto in SLOTR, align slot width on data size
@@ -831,16 +881,16 @@ static int stm32_sai_set_slots(struct snd_soc_dai *cpu_dai)
 		sai->slots = 2;
 
 	/* The number of slots in the audio frame is equal to NBSLOT[3:0] + 1*/
-	regmap_update_bits(sai->regmap, STM_SAI_SLOTR_REGX,
-			   SAI_XSLOTR_NBSLOT_MASK,
-			   SAI_XSLOTR_NBSLOT_SET((sai->slots - 1)));
+	stm32_sai_sub_reg_up(sai, STM_SAI_SLOTR_REGX,
+			     SAI_XSLOTR_NBSLOT_MASK,
+			     SAI_XSLOTR_NBSLOT_SET((sai->slots - 1)));
 
 	/* Set default slots mask if not already set from DT */
 	if (!(slotr & SAI_XSLOTR_SLOTEN_MASK)) {
 		sai->slot_mask = (1 << sai->slots) - 1;
-		regmap_update_bits(sai->regmap,
-				   STM_SAI_SLOTR_REGX, SAI_XSLOTR_SLOTEN_MASK,
-				   SAI_XSLOTR_SLOTEN_SET(sai->slot_mask));
+		stm32_sai_sub_reg_up(sai,
+				     STM_SAI_SLOTR_REGX, SAI_XSLOTR_SLOTEN_MASK,
+				     SAI_XSLOTR_SLOTEN_SET(sai->slot_mask));
 	}
 
 	dev_dbg(cpu_dai->dev, "Slots %d, slot width %d\n",
@@ -870,14 +920,14 @@ static void stm32_sai_set_frame(struct snd_soc_dai *cpu_dai)
 	dev_dbg(cpu_dai->dev, "Frame length %d, frame active %d\n",
 		sai->fs_length, fs_active);
 
-	regmap_update_bits(sai->regmap, STM_SAI_FRCR_REGX, frcr_mask, frcr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_FRCR_REGX, frcr_mask, frcr);
 
 	if ((sai->fmt & SND_SOC_DAIFMT_FORMAT_MASK) == SND_SOC_DAIFMT_LSB) {
 		offset = sai->slot_width - sai->data_size;
 
-		regmap_update_bits(sai->regmap, STM_SAI_SLOTR_REGX,
-				   SAI_XSLOTR_FBOFF_MASK,
-				   SAI_XSLOTR_FBOFF_SET(offset));
+		stm32_sai_sub_reg_up(sai, STM_SAI_SLOTR_REGX,
+				     SAI_XSLOTR_FBOFF_MASK,
+				     SAI_XSLOTR_FBOFF_SET(offset));
 	}
 }
 
@@ -994,9 +1044,9 @@ static int stm32_sai_configure_clock(struct snd_soc_dai *cpu_dai,
 					return -EINVAL;
 				}
 
-				regmap_update_bits(sai->regmap,
-						   STM_SAI_CR1_REGX,
-						   SAI_XCR1_OSR, cr1);
+				stm32_sai_sub_reg_up(sai,
+						     STM_SAI_CR1_REGX,
+						     SAI_XCR1_OSR, cr1);
 
 				div = stm32_sai_get_clk_div(sai, sai_clk_rate,
 							    sai->mclk_rate);
@@ -1058,12 +1108,12 @@ static int stm32_sai_trigger(struct snd_pcm_substream *substream, int cmd,
 	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
 		dev_dbg(cpu_dai->dev, "Enable DMA and SAI\n");
 
-		regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-				   SAI_XCR1_DMAEN, SAI_XCR1_DMAEN);
+		stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+				     SAI_XCR1_DMAEN, SAI_XCR1_DMAEN);
 
 		/* Enable SAI */
-		ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-					 SAI_XCR1_SAIEN, SAI_XCR1_SAIEN);
+		ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+					   SAI_XCR1_SAIEN, SAI_XCR1_SAIEN);
 		if (ret < 0)
 			dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 		break;
@@ -1072,16 +1122,16 @@ static int stm32_sai_trigger(struct snd_pcm_substream *substream, int cmd,
 	case SNDRV_PCM_TRIGGER_STOP:
 		dev_dbg(cpu_dai->dev, "Disable DMA and SAI\n");
 
-		regmap_update_bits(sai->regmap, STM_SAI_IMR_REGX,
-				   SAI_XIMR_MASK, 0);
+		stm32_sai_sub_reg_up(sai, STM_SAI_IMR_REGX,
+				     SAI_XIMR_MASK, 0);
 
-		regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-				   SAI_XCR1_SAIEN,
-				   (unsigned int)~SAI_XCR1_SAIEN);
+		stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+				     SAI_XCR1_SAIEN,
+				     (unsigned int)~SAI_XCR1_SAIEN);
 
-		ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-					 SAI_XCR1_DMAEN,
-					 (unsigned int)~SAI_XCR1_DMAEN);
+		ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+					   SAI_XCR1_DMAEN,
+					   (unsigned int)~SAI_XCR1_DMAEN);
 		if (ret < 0)
 			dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 
@@ -1101,7 +1151,7 @@ static void stm32_sai_shutdown(struct snd_pcm_substream *substream,
 	struct stm32_sai_sub_data *sai = snd_soc_dai_get_drvdata(cpu_dai);
 	unsigned long flags;
 
-	regmap_update_bits(sai->regmap, STM_SAI_IMR_REGX, SAI_XIMR_MASK, 0);
+	stm32_sai_sub_reg_up(sai, STM_SAI_IMR_REGX, SAI_XIMR_MASK, 0);
 
 	clk_disable_unprepare(sai->sai_ck);
 
@@ -1169,7 +1219,7 @@ static int stm32_sai_dai_probe(struct snd_soc_dai *cpu_dai)
 	cr1_mask |= SAI_XCR1_SYNCEN_MASK;
 	cr1 |= SAI_XCR1_SYNCEN_SET(sai->sync);
 
-	return regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, cr1_mask, cr1);
+	return stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, cr1_mask, cr1);
 }
 
 static const struct snd_soc_dai_ops stm32_sai_pcm_dai_ops = {
@@ -1322,8 +1372,13 @@ static int stm32_sai_sub_parse_of(struct platform_device *pdev,
 	if (STM_SAI_HAS_PDM(sai) && STM_SAI_IS_SUB_A(sai))
 		sai->regmap_config = &stm32_sai_sub_regmap_config_h7;
 
-	sai->regmap = devm_regmap_init_mmio_clk(&pdev->dev, "sai_ck",
-						base, sai->regmap_config);
+	/*
+	 * Do not manage peripheral clock through regmap framework as this
+	 * can lead to circular locking issue with sai master clock provider.
+	 * Manage peripheral clock directly in driver instead.
+	 */
+	sai->regmap = devm_regmap_init_mmio(&pdev->dev, base,
+					    sai->regmap_config);
 	if (IS_ERR(sai->regmap)) {
 		dev_err(&pdev->dev, "Failed to initialize MMIO\n");
 		return PTR_ERR(sai->regmap);
@@ -1420,6 +1475,10 @@ static int stm32_sai_sub_parse_of(struct platform_device *pdev,
 		return PTR_ERR(sai->sai_ck);
 	}
 
+	ret = clk_prepare(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
 	if (STM_SAI_IS_F4(sai->pdata))
 		return 0;
 
@@ -1501,22 +1560,48 @@ static int stm32_sai_sub_probe(struct platform_device *pdev)
 	return 0;
 }
 
+static int stm32_sai_sub_remove(struct platform_device *pdev)
+{
+	struct stm32_sai_sub_data *sai = dev_get_drvdata(&pdev->dev);
+
+	clk_unprepare(sai->pdata->pclk);
+
+	return 0;
+}
+
 #ifdef CONFIG_PM_SLEEP
 static int stm32_sai_sub_suspend(struct device *dev)
 {
 	struct stm32_sai_sub_data *sai = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
 
 	regcache_cache_only(sai->regmap, true);
 	regcache_mark_dirty(sai->regmap);
+
+	clk_disable(sai->pdata->pclk);
+
 	return 0;
 }
 
 static int stm32_sai_sub_resume(struct device *dev)
 {
 	struct stm32_sai_sub_data *sai = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
 
 	regcache_cache_only(sai->regmap, false);
-	return regcache_sync(sai->regmap);
+	ret = regcache_sync(sai->regmap);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
 }
 #endif /* CONFIG_PM_SLEEP */
 
@@ -1531,6 +1616,7 @@ static struct platform_driver stm32_sai_sub_driver = {
 		.pm = &stm32_sai_sub_pm_ops,
 	},
 	.probe = stm32_sai_sub_probe,
+	.remove = stm32_sai_sub_remove,
 };
 
 module_platform_driver(stm32_sai_sub_driver);
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[alsa-devel] [PATCH AUTOSEL 5.4 043/107] ASoC: stm32: sai: fix possible circular locking

[Sasha Levin]

From: Olivier Moysan <olivier.moysan@st.com>

[ Upstream commit a14bf98c045bf119b7e779f186528e38c6428830 ]

In current driver, locks can be taken as follows:
- Register access: take a lock on regmap config and then on clock.
- Master clock provider: take a lock on clock and then on regmap config.
This can lead to the circular locking summarized below.

Remove peripheral clock management through regmap framework, and manage
peripheral clock in driver instead. On register access, lock on clock
is taken first, which allows to avoid possible locking issue.

[ 6696.561513] ======================================================
[ 6696.567670] WARNING: possible circular locking dependency detected
[ 6696.573842] 4.19.49 #866 Not tainted
[ 6696.577397] ------------------------------------------------------
[ 6696.583566] pulseaudio/6439 is trying to acquire lock:
[ 6696.588697] 87b0a25b (enable_lock){..-.}, at: clk_enable_lock+0x64/0x128
[ 6696.595377]
[ 6696.595377] but task is already holding lock:
[ 6696.601197] d858f825 (stm32_sai_sub:1342:(sai->regmap_config)->lock){....}
...
[ 6696.812513]  Possible unsafe locking scenario:
[ 6696.812513]
[ 6696.818418]        CPU0                    CPU1
[ 6696.822935]        ----                    ----
[ 6696.827451]   lock(stm32_sai_sub:1342:(sai->regmap_config)->lock);
[ 6696.833618]                                lock(enable_lock);
[ 6696.839350]                                lock(stm32_sai_sub:1342:
                                              (sai->regmap_config)->lock);
[ 6696.848035]   lock(enable_lock);

Fixes: 03e78a242a15 ("ASoC: stm32: sai: add h7 support")

Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200109083254.478-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/stm/stm32_sai_sub.c | 194 ++++++++++++++++++++++++----------
 1 file changed, 140 insertions(+), 54 deletions(-)

diff --git a/sound/soc/stm/stm32_sai_sub.c b/sound/soc/stm/stm32_sai_sub.c
index 48e629ac2d88b..30bcd5d3a32a8 100644
--- a/sound/soc/stm/stm32_sai_sub.c
+++ b/sound/soc/stm/stm32_sai_sub.c
@@ -184,6 +184,56 @@ static bool stm32_sai_sub_writeable_reg(struct device *dev, unsigned int reg)
 	}
 }
 
+static int stm32_sai_sub_reg_up(struct stm32_sai_sub_data *sai,
+				unsigned int reg, unsigned int mask,
+				unsigned int val)
+{
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_update_bits(sai->regmap, reg, mask, val);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
+}
+
+static int stm32_sai_sub_reg_wr(struct stm32_sai_sub_data *sai,
+				unsigned int reg, unsigned int mask,
+				unsigned int val)
+{
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_write_bits(sai->regmap, reg, mask, val);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
+}
+
+static int stm32_sai_sub_reg_rd(struct stm32_sai_sub_data *sai,
+				unsigned int reg, unsigned int *val)
+{
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_read(sai->regmap, reg, val);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
+}
+
 static const struct regmap_config stm32_sai_sub_regmap_config_f4 = {
 	.reg_bits = 32,
 	.reg_stride = 4,
@@ -295,7 +345,7 @@ static int stm32_sai_set_clk_div(struct stm32_sai_sub_data *sai,
 
 	mask = SAI_XCR1_MCKDIV_MASK(SAI_XCR1_MCKDIV_WIDTH(version));
 	cr1 = SAI_XCR1_MCKDIV_SET(div);
-	ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, mask, cr1);
+	ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, mask, cr1);
 	if (ret < 0)
 		dev_err(&sai->pdev->dev, "Failed to update CR1 register\n");
 
@@ -372,8 +422,8 @@ static int stm32_sai_mclk_enable(struct clk_hw *hw)
 
 	dev_dbg(&sai->pdev->dev, "Enable master clock\n");
 
-	return regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-				  SAI_XCR1_MCKEN, SAI_XCR1_MCKEN);
+	return stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+				    SAI_XCR1_MCKEN, SAI_XCR1_MCKEN);
 }
 
 static void stm32_sai_mclk_disable(struct clk_hw *hw)
@@ -383,7 +433,7 @@ static void stm32_sai_mclk_disable(struct clk_hw *hw)
 
 	dev_dbg(&sai->pdev->dev, "Disable master clock\n");
 
-	regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, SAI_XCR1_MCKEN, 0);
+	stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, SAI_XCR1_MCKEN, 0);
 }
 
 static const struct clk_ops mclk_ops = {
@@ -446,15 +496,15 @@ static irqreturn_t stm32_sai_isr(int irq, void *devid)
 	unsigned int sr, imr, flags;
 	snd_pcm_state_t status = SNDRV_PCM_STATE_RUNNING;
 
-	regmap_read(sai->regmap, STM_SAI_IMR_REGX, &imr);
-	regmap_read(sai->regmap, STM_SAI_SR_REGX, &sr);
+	stm32_sai_sub_reg_rd(sai, STM_SAI_IMR_REGX, &imr);
+	stm32_sai_sub_reg_rd(sai, STM_SAI_SR_REGX, &sr);
 
 	flags = sr & imr;
 	if (!flags)
 		return IRQ_NONE;
 
-	regmap_write_bits(sai->regmap, STM_SAI_CLRFR_REGX, SAI_XCLRFR_MASK,
-			  SAI_XCLRFR_MASK);
+	stm32_sai_sub_reg_wr(sai, STM_SAI_CLRFR_REGX, SAI_XCLRFR_MASK,
+			     SAI_XCLRFR_MASK);
 
 	if (!sai->substream) {
 		dev_err(&pdev->dev, "Device stopped. Spurious IRQ 0x%x\n", sr);
@@ -503,8 +553,8 @@ static int stm32_sai_set_sysclk(struct snd_soc_dai *cpu_dai,
 	int ret;
 
 	if (dir == SND_SOC_CLOCK_OUT && sai->sai_mclk) {
-		ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-					 SAI_XCR1_NODIV,
+		ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+					   SAI_XCR1_NODIV,
 					 freq ? 0 : SAI_XCR1_NODIV);
 		if (ret < 0)
 			return ret;
@@ -583,7 +633,7 @@ static int stm32_sai_set_dai_tdm_slot(struct snd_soc_dai *cpu_dai, u32 tx_mask,
 
 	slotr_mask |= SAI_XSLOTR_SLOTEN_MASK;
 
-	regmap_update_bits(sai->regmap, STM_SAI_SLOTR_REGX, slotr_mask, slotr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_SLOTR_REGX, slotr_mask, slotr);
 
 	sai->slot_width = slot_width;
 	sai->slots = slots;
@@ -665,7 +715,7 @@ static int stm32_sai_set_dai_fmt(struct snd_soc_dai *cpu_dai, unsigned int fmt)
 	cr1_mask |= SAI_XCR1_CKSTR;
 	frcr_mask |= SAI_XFRCR_FSPOL;
 
-	regmap_update_bits(sai->regmap, STM_SAI_FRCR_REGX, frcr_mask, frcr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_FRCR_REGX, frcr_mask, frcr);
 
 	/* DAI clock master masks */
 	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
@@ -693,7 +743,7 @@ static int stm32_sai_set_dai_fmt(struct snd_soc_dai *cpu_dai, unsigned int fmt)
 	cr1_mask |= SAI_XCR1_SLAVE;
 
 conf_update:
-	ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, cr1_mask, cr1);
+	ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, cr1_mask, cr1);
 	if (ret < 0) {
 		dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 		return ret;
@@ -730,12 +780,12 @@ static int stm32_sai_startup(struct snd_pcm_substream *substream,
 	}
 
 	/* Enable ITs */
-	regmap_write_bits(sai->regmap, STM_SAI_CLRFR_REGX,
-			  SAI_XCLRFR_MASK, SAI_XCLRFR_MASK);
+	stm32_sai_sub_reg_wr(sai, STM_SAI_CLRFR_REGX,
+			     SAI_XCLRFR_MASK, SAI_XCLRFR_MASK);
 
 	imr = SAI_XIMR_OVRUDRIE;
 	if (STM_SAI_IS_CAPTURE(sai)) {
-		regmap_read(sai->regmap, STM_SAI_CR2_REGX, &cr2);
+		stm32_sai_sub_reg_rd(sai, STM_SAI_CR2_REGX, &cr2);
 		if (cr2 & SAI_XCR2_MUTECNT_MASK)
 			imr |= SAI_XIMR_MUTEDETIE;
 	}
@@ -745,8 +795,8 @@ static int stm32_sai_startup(struct snd_pcm_substream *substream,
 	else
 		imr |= SAI_XIMR_AFSDETIE | SAI_XIMR_LFSDETIE;
 
-	regmap_update_bits(sai->regmap, STM_SAI_IMR_REGX,
-			   SAI_XIMR_MASK, imr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_IMR_REGX,
+			     SAI_XIMR_MASK, imr);
 
 	return 0;
 }
@@ -763,10 +813,10 @@ static int stm32_sai_set_config(struct snd_soc_dai *cpu_dai,
 	 * SAI fifo threshold is set to half fifo, to keep enough space
 	 * for DMA incoming bursts.
 	 */
-	regmap_write_bits(sai->regmap, STM_SAI_CR2_REGX,
-			  SAI_XCR2_FFLUSH | SAI_XCR2_FTH_MASK,
-			  SAI_XCR2_FFLUSH |
-			  SAI_XCR2_FTH_SET(STM_SAI_FIFO_TH_HALF));
+	stm32_sai_sub_reg_wr(sai, STM_SAI_CR2_REGX,
+			     SAI_XCR2_FFLUSH | SAI_XCR2_FTH_MASK,
+			     SAI_XCR2_FFLUSH |
+			     SAI_XCR2_FTH_SET(STM_SAI_FIFO_TH_HALF));
 
 	/* DS bits in CR1 not set for SPDIF (size forced to 24 bits).*/
 	if (STM_SAI_PROTOCOL_IS_SPDIF(sai)) {
@@ -795,7 +845,7 @@ static int stm32_sai_set_config(struct snd_soc_dai *cpu_dai,
 	if ((sai->slots == 2) && (params_channels(params) == 1))
 		cr1 |= SAI_XCR1_MONO;
 
-	ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, cr1_mask, cr1);
+	ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, cr1_mask, cr1);
 	if (ret < 0) {
 		dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 		return ret;
@@ -809,7 +859,7 @@ static int stm32_sai_set_slots(struct snd_soc_dai *cpu_dai)
 	struct stm32_sai_sub_data *sai = snd_soc_dai_get_drvdata(cpu_dai);
 	int slotr, slot_sz;
 
-	regmap_read(sai->regmap, STM_SAI_SLOTR_REGX, &slotr);
+	stm32_sai_sub_reg_rd(sai, STM_SAI_SLOTR_REGX, &slotr);
 
 	/*
 	 * If SLOTSZ is set to auto in SLOTR, align slot width on data size
@@ -831,16 +881,16 @@ static int stm32_sai_set_slots(struct snd_soc_dai *cpu_dai)
 		sai->slots = 2;
 
 	/* The number of slots in the audio frame is equal to NBSLOT[3:0] + 1*/
-	regmap_update_bits(sai->regmap, STM_SAI_SLOTR_REGX,
-			   SAI_XSLOTR_NBSLOT_MASK,
-			   SAI_XSLOTR_NBSLOT_SET((sai->slots - 1)));
+	stm32_sai_sub_reg_up(sai, STM_SAI_SLOTR_REGX,
+			     SAI_XSLOTR_NBSLOT_MASK,
+			     SAI_XSLOTR_NBSLOT_SET((sai->slots - 1)));
 
 	/* Set default slots mask if not already set from DT */
 	if (!(slotr & SAI_XSLOTR_SLOTEN_MASK)) {
 		sai->slot_mask = (1 << sai->slots) - 1;
-		regmap_update_bits(sai->regmap,
-				   STM_SAI_SLOTR_REGX, SAI_XSLOTR_SLOTEN_MASK,
-				   SAI_XSLOTR_SLOTEN_SET(sai->slot_mask));
+		stm32_sai_sub_reg_up(sai,
+				     STM_SAI_SLOTR_REGX, SAI_XSLOTR_SLOTEN_MASK,
+				     SAI_XSLOTR_SLOTEN_SET(sai->slot_mask));
 	}
 
 	dev_dbg(cpu_dai->dev, "Slots %d, slot width %d\n",
@@ -870,14 +920,14 @@ static void stm32_sai_set_frame(struct snd_soc_dai *cpu_dai)
 	dev_dbg(cpu_dai->dev, "Frame length %d, frame active %d\n",
 		sai->fs_length, fs_active);
 
-	regmap_update_bits(sai->regmap, STM_SAI_FRCR_REGX, frcr_mask, frcr);
+	stm32_sai_sub_reg_up(sai, STM_SAI_FRCR_REGX, frcr_mask, frcr);
 
 	if ((sai->fmt & SND_SOC_DAIFMT_FORMAT_MASK) == SND_SOC_DAIFMT_LSB) {
 		offset = sai->slot_width - sai->data_size;
 
-		regmap_update_bits(sai->regmap, STM_SAI_SLOTR_REGX,
-				   SAI_XSLOTR_FBOFF_MASK,
-				   SAI_XSLOTR_FBOFF_SET(offset));
+		stm32_sai_sub_reg_up(sai, STM_SAI_SLOTR_REGX,
+				     SAI_XSLOTR_FBOFF_MASK,
+				     SAI_XSLOTR_FBOFF_SET(offset));
 	}
 }
 
@@ -994,9 +1044,9 @@ static int stm32_sai_configure_clock(struct snd_soc_dai *cpu_dai,
 					return -EINVAL;
 				}
 
-				regmap_update_bits(sai->regmap,
-						   STM_SAI_CR1_REGX,
-						   SAI_XCR1_OSR, cr1);
+				stm32_sai_sub_reg_up(sai,
+						     STM_SAI_CR1_REGX,
+						     SAI_XCR1_OSR, cr1);
 
 				div = stm32_sai_get_clk_div(sai, sai_clk_rate,
 							    sai->mclk_rate);
@@ -1058,12 +1108,12 @@ static int stm32_sai_trigger(struct snd_pcm_substream *substream, int cmd,
 	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
 		dev_dbg(cpu_dai->dev, "Enable DMA and SAI\n");
 
-		regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-				   SAI_XCR1_DMAEN, SAI_XCR1_DMAEN);
+		stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+				     SAI_XCR1_DMAEN, SAI_XCR1_DMAEN);
 
 		/* Enable SAI */
-		ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-					 SAI_XCR1_SAIEN, SAI_XCR1_SAIEN);
+		ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+					   SAI_XCR1_SAIEN, SAI_XCR1_SAIEN);
 		if (ret < 0)
 			dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 		break;
@@ -1072,16 +1122,16 @@ static int stm32_sai_trigger(struct snd_pcm_substream *substream, int cmd,
 	case SNDRV_PCM_TRIGGER_STOP:
 		dev_dbg(cpu_dai->dev, "Disable DMA and SAI\n");
 
-		regmap_update_bits(sai->regmap, STM_SAI_IMR_REGX,
-				   SAI_XIMR_MASK, 0);
+		stm32_sai_sub_reg_up(sai, STM_SAI_IMR_REGX,
+				     SAI_XIMR_MASK, 0);
 
-		regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-				   SAI_XCR1_SAIEN,
-				   (unsigned int)~SAI_XCR1_SAIEN);
+		stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+				     SAI_XCR1_SAIEN,
+				     (unsigned int)~SAI_XCR1_SAIEN);
 
-		ret = regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX,
-					 SAI_XCR1_DMAEN,
-					 (unsigned int)~SAI_XCR1_DMAEN);
+		ret = stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX,
+					   SAI_XCR1_DMAEN,
+					   (unsigned int)~SAI_XCR1_DMAEN);
 		if (ret < 0)
 			dev_err(cpu_dai->dev, "Failed to update CR1 register\n");
 
@@ -1101,7 +1151,7 @@ static void stm32_sai_shutdown(struct snd_pcm_substream *substream,
 	struct stm32_sai_sub_data *sai = snd_soc_dai_get_drvdata(cpu_dai);
 	unsigned long flags;
 
-	regmap_update_bits(sai->regmap, STM_SAI_IMR_REGX, SAI_XIMR_MASK, 0);
+	stm32_sai_sub_reg_up(sai, STM_SAI_IMR_REGX, SAI_XIMR_MASK, 0);
 
 	clk_disable_unprepare(sai->sai_ck);
 
@@ -1169,7 +1219,7 @@ static int stm32_sai_dai_probe(struct snd_soc_dai *cpu_dai)
 	cr1_mask |= SAI_XCR1_SYNCEN_MASK;
 	cr1 |= SAI_XCR1_SYNCEN_SET(sai->sync);
 
-	return regmap_update_bits(sai->regmap, STM_SAI_CR1_REGX, cr1_mask, cr1);
+	return stm32_sai_sub_reg_up(sai, STM_SAI_CR1_REGX, cr1_mask, cr1);
 }
 
 static const struct snd_soc_dai_ops stm32_sai_pcm_dai_ops = {
@@ -1322,8 +1372,13 @@ static int stm32_sai_sub_parse_of(struct platform_device *pdev,
 	if (STM_SAI_HAS_PDM(sai) && STM_SAI_IS_SUB_A(sai))
 		sai->regmap_config = &stm32_sai_sub_regmap_config_h7;
 
-	sai->regmap = devm_regmap_init_mmio_clk(&pdev->dev, "sai_ck",
-						base, sai->regmap_config);
+	/*
+	 * Do not manage peripheral clock through regmap framework as this
+	 * can lead to circular locking issue with sai master clock provider.
+	 * Manage peripheral clock directly in driver instead.
+	 */
+	sai->regmap = devm_regmap_init_mmio(&pdev->dev, base,
+					    sai->regmap_config);
 	if (IS_ERR(sai->regmap)) {
 		dev_err(&pdev->dev, "Failed to initialize MMIO\n");
 		return PTR_ERR(sai->regmap);
@@ -1420,6 +1475,10 @@ static int stm32_sai_sub_parse_of(struct platform_device *pdev,
 		return PTR_ERR(sai->sai_ck);
 	}
 
+	ret = clk_prepare(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
+
 	if (STM_SAI_IS_F4(sai->pdata))
 		return 0;
 
@@ -1501,22 +1560,48 @@ static int stm32_sai_sub_probe(struct platform_device *pdev)
 	return 0;
 }
 
+static int stm32_sai_sub_remove(struct platform_device *pdev)
+{
+	struct stm32_sai_sub_data *sai = dev_get_drvdata(&pdev->dev);
+
+	clk_unprepare(sai->pdata->pclk);
+
+	return 0;
+}
+
 #ifdef CONFIG_PM_SLEEP
 static int stm32_sai_sub_suspend(struct device *dev)
 {
 	struct stm32_sai_sub_data *sai = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
 
 	regcache_cache_only(sai->regmap, true);
 	regcache_mark_dirty(sai->regmap);
+
+	clk_disable(sai->pdata->pclk);
+
 	return 0;
 }
 
 static int stm32_sai_sub_resume(struct device *dev)
 {
 	struct stm32_sai_sub_data *sai = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_enable(sai->pdata->pclk);
+	if (ret < 0)
+		return ret;
 
 	regcache_cache_only(sai->regmap, false);
-	return regcache_sync(sai->regmap);
+	ret = regcache_sync(sai->regmap);
+
+	clk_disable(sai->pdata->pclk);
+
+	return ret;
 }
 #endif /* CONFIG_PM_SLEEP */
 
@@ -1531,6 +1616,7 @@ static struct platform_driver stm32_sai_sub_driver = {
 		.pm = &stm32_sai_sub_pm_ops,
 	},
 	.probe = stm32_sai_sub_probe,
+	.remove = stm32_sai_sub_remove,
 };
 
 module_platform_driver(stm32_sai_sub_driver);
-- 
2.20.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel

[PATCH AUTOSEL 5.4 044/107] bpf/sockmap: Read psock ingress_msg before sk_receive_queue

[Sasha Levin]

From: Lingpeng Chen <forrest0579@gmail.com>

[ Upstream commit e7a5f1f1cd0008e5ad379270a8657e121eedb669 ]

Right now in tcp_bpf_recvmsg, sock read data first from sk_receive_queue
if not empty than psock->ingress_msg otherwise. If a FIN packet arrives
and there's also some data in psock->ingress_msg, the data in
psock->ingress_msg will be purged. It is always happen when request to a
HTTP1.0 server like python SimpleHTTPServer since the server send FIN
packet after data is sent out.

Fixes: 604326b41a6fb ("bpf, sockmap: convert to generic sk_msg interface")
Reported-by: Arika Chen <eaglesora@gmail.com>
Suggested-by: Arika Chen <eaglesora@gmail.com>
Signed-off-by: Lingpeng Chen <forrest0579@gmail.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200109014833.18951-1-forrest0579@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/ipv4/tcp_bpf.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/net/ipv4/tcp_bpf.c b/net/ipv4/tcp_bpf.c
index e38705165ac9b..e6b08b5a08955 100644
--- a/net/ipv4/tcp_bpf.c
+++ b/net/ipv4/tcp_bpf.c
@@ -121,14 +121,14 @@ int tcp_bpf_recvmsg(struct sock *sk, struct msghdr *msg, size_t len,
 	struct sk_psock *psock;
 	int copied, ret;
 
-	if (unlikely(flags & MSG_ERRQUEUE))
-		return inet_recv_error(sk, msg, len, addr_len);
-	if (!skb_queue_empty(&sk->sk_receive_queue))
-		return tcp_recvmsg(sk, msg, len, nonblock, flags, addr_len);
-
 	psock = sk_psock_get(sk);
 	if (unlikely(!psock))
 		return tcp_recvmsg(sk, msg, len, nonblock, flags, addr_len);
+	if (unlikely(flags & MSG_ERRQUEUE))
+		return inet_recv_error(sk, msg, len, addr_len);
+	if (!skb_queue_empty(&sk->sk_receive_queue) &&
+	    sk_psock_queue_empty(psock))
+		return tcp_recvmsg(sk, msg, len, nonblock, flags, addr_len);
 	lock_sock(sk);
 msg_bytes_ready:
 	copied = __tcp_bpf_recvmsg(sk, psock, msg, len, flags);
@@ -139,7 +139,7 @@ msg_bytes_ready:
 		timeo = sock_rcvtimeo(sk, nonblock);
 		data = tcp_bpf_wait_data(sk, psock, flags, timeo, &err);
 		if (data) {
-			if (skb_queue_empty(&sk->sk_receive_queue))
+			if (!sk_psock_queue_empty(psock))
 				goto msg_bytes_ready;
 			release_sock(sk);
 			sk_psock_put(sk, psock);
-- 
2.20.1

[PATCH AUTOSEL 5.4 045/107] sh_eth: check sh_eth_cpu_data::dual_port when dumping registers

[Sasha Levin]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

[ Upstream commit 3249b1e442a1be1a6b9f1026785b519d1443f807 ]

When adding the sh_eth_cpu_data::dual_port flag I forgot to add the flag
checks to __sh_eth_get_regs(), causing the non-existing TSU registers to
be dumped by 'ethtool' on the single port Ether controllers having TSU...

Fixes: a94cf2a614f8 ("sh_eth: fix TSU init on SH7734/R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/renesas/sh_eth.c | 38 +++++++++++++++------------
 1 file changed, 21 insertions(+), 17 deletions(-)

diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c
index 7ba35a0bdb292..8aa1b1bda96d1 100644
--- a/drivers/net/ethernet/renesas/sh_eth.c
+++ b/drivers/net/ethernet/renesas/sh_eth.c
@@ -2204,24 +2204,28 @@ static size_t __sh_eth_get_regs(struct net_device *ndev, u32 *buf)
 	if (cd->tsu) {
 		add_tsu_reg(ARSTR);
 		add_tsu_reg(TSU_CTRST);
-		add_tsu_reg(TSU_FWEN0);
-		add_tsu_reg(TSU_FWEN1);
-		add_tsu_reg(TSU_FCM);
-		add_tsu_reg(TSU_BSYSL0);
-		add_tsu_reg(TSU_BSYSL1);
-		add_tsu_reg(TSU_PRISL0);
-		add_tsu_reg(TSU_PRISL1);
-		add_tsu_reg(TSU_FWSL0);
-		add_tsu_reg(TSU_FWSL1);
+		if (cd->dual_port) {
+			add_tsu_reg(TSU_FWEN0);
+			add_tsu_reg(TSU_FWEN1);
+			add_tsu_reg(TSU_FCM);
+			add_tsu_reg(TSU_BSYSL0);
+			add_tsu_reg(TSU_BSYSL1);
+			add_tsu_reg(TSU_PRISL0);
+			add_tsu_reg(TSU_PRISL1);
+			add_tsu_reg(TSU_FWSL0);
+			add_tsu_reg(TSU_FWSL1);
+		}
 		add_tsu_reg(TSU_FWSLC);
-		add_tsu_reg(TSU_QTAGM0);
-		add_tsu_reg(TSU_QTAGM1);
-		add_tsu_reg(TSU_FWSR);
-		add_tsu_reg(TSU_FWINMK);
-		add_tsu_reg(TSU_ADQT0);
-		add_tsu_reg(TSU_ADQT1);
-		add_tsu_reg(TSU_VTAG0);
-		add_tsu_reg(TSU_VTAG1);
+		if (cd->dual_port) {
+			add_tsu_reg(TSU_QTAGM0);
+			add_tsu_reg(TSU_QTAGM1);
+			add_tsu_reg(TSU_FWSR);
+			add_tsu_reg(TSU_FWINMK);
+			add_tsu_reg(TSU_ADQT0);
+			add_tsu_reg(TSU_ADQT1);
+			add_tsu_reg(TSU_VTAG0);
+			add_tsu_reg(TSU_VTAG1);
+		}
 		add_tsu_reg(TSU_ADSBSY);
 		add_tsu_reg(TSU_TEN);
 		add_tsu_reg(TSU_POST1);
-- 
2.20.1

[PATCH AUTOSEL 5.4 045/107] sh_eth: check sh_eth_cpu_data::dual_port when dumping registers

[Sasha Levin]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

[ Upstream commit 3249b1e442a1be1a6b9f1026785b519d1443f807 ]

When adding the sh_eth_cpu_data::dual_port flag I forgot to add the flag
checks to __sh_eth_get_regs(), causing the non-existing TSU registers to
be dumped by 'ethtool' on the single port Ether controllers having TSU...

Fixes: a94cf2a614f8 ("sh_eth: fix TSU init on SH7734/R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/renesas/sh_eth.c | 38 +++++++++++++++------------
 1 file changed, 21 insertions(+), 17 deletions(-)

diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c
index 7ba35a0bdb292..8aa1b1bda96d1 100644
--- a/drivers/net/ethernet/renesas/sh_eth.c
+++ b/drivers/net/ethernet/renesas/sh_eth.c
@@ -2204,24 +2204,28 @@ static size_t __sh_eth_get_regs(struct net_device *ndev, u32 *buf)
 	if (cd->tsu) {
 		add_tsu_reg(ARSTR);
 		add_tsu_reg(TSU_CTRST);
-		add_tsu_reg(TSU_FWEN0);
-		add_tsu_reg(TSU_FWEN1);
-		add_tsu_reg(TSU_FCM);
-		add_tsu_reg(TSU_BSYSL0);
-		add_tsu_reg(TSU_BSYSL1);
-		add_tsu_reg(TSU_PRISL0);
-		add_tsu_reg(TSU_PRISL1);
-		add_tsu_reg(TSU_FWSL0);
-		add_tsu_reg(TSU_FWSL1);
+		if (cd->dual_port) {
+			add_tsu_reg(TSU_FWEN0);
+			add_tsu_reg(TSU_FWEN1);
+			add_tsu_reg(TSU_FCM);
+			add_tsu_reg(TSU_BSYSL0);
+			add_tsu_reg(TSU_BSYSL1);
+			add_tsu_reg(TSU_PRISL0);
+			add_tsu_reg(TSU_PRISL1);
+			add_tsu_reg(TSU_FWSL0);
+			add_tsu_reg(TSU_FWSL1);
+		}
 		add_tsu_reg(TSU_FWSLC);
-		add_tsu_reg(TSU_QTAGM0);
-		add_tsu_reg(TSU_QTAGM1);
-		add_tsu_reg(TSU_FWSR);
-		add_tsu_reg(TSU_FWINMK);
-		add_tsu_reg(TSU_ADQT0);
-		add_tsu_reg(TSU_ADQT1);
-		add_tsu_reg(TSU_VTAG0);
-		add_tsu_reg(TSU_VTAG1);
+		if (cd->dual_port) {
+			add_tsu_reg(TSU_QTAGM0);
+			add_tsu_reg(TSU_QTAGM1);
+			add_tsu_reg(TSU_FWSR);
+			add_tsu_reg(TSU_FWINMK);
+			add_tsu_reg(TSU_ADQT0);
+			add_tsu_reg(TSU_ADQT1);
+			add_tsu_reg(TSU_VTAG0);
+			add_tsu_reg(TSU_VTAG1);
+		}
 		add_tsu_reg(TSU_ADSBSY);
 		add_tsu_reg(TSU_TEN);
 		add_tsu_reg(TSU_POST1);
-- 
2.20.1

[PATCH AUTOSEL 5.4 046/107] ASoC: stm32: dfsdm: fix 16 bits record

[Sasha Levin]

From: Olivier Moysan <olivier.moysan@st.com>

[ Upstream commit 8e55ea19125b65cffe42747359af99d545e85f2f ]

In stm32_afsdm_pcm_cb function, the transfer size is provided in bytes.
However, samples are copied as 16 bits words from iio buffer.
Divide by two the transfer size, to copy the right number of samples.

Fixes: 1e7f6e1c69f0 ("ASoC: stm32: dfsdm: add 16 bits audio record support")

Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200110131131.3191-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/stm/stm32_adfsdm.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/sound/soc/stm/stm32_adfsdm.c b/sound/soc/stm/stm32_adfsdm.c
index 3c9a9deec9af4..4ecea4913f427 100644
--- a/sound/soc/stm/stm32_adfsdm.c
+++ b/sound/soc/stm/stm32_adfsdm.c
@@ -153,13 +153,13 @@ static const struct snd_soc_component_driver stm32_adfsdm_dai_component = {
 	.name = "stm32_dfsdm_audio",
 };
 
-static void memcpy_32to16(void *dest, const void *src, size_t n)
+static void stm32_memcpy_32to16(void *dest, const void *src, size_t n)
 {
 	unsigned int i = 0;
 	u16 *d = (u16 *)dest, *s = (u16 *)src;
 
 	s++;
-	for (i = n; i > 0; i--) {
+	for (i = n >> 1; i > 0; i--) {
 		*d++ = *s++;
 		s++;
 	}
@@ -186,8 +186,8 @@ static int stm32_afsdm_pcm_cb(const void *data, size_t size, void *private)
 
 	if ((priv->pos + src_size) > buff_size) {
 		if (format == SNDRV_PCM_FORMAT_S16_LE)
-			memcpy_32to16(&pcm_buff[priv->pos], src_buff,
-				      buff_size - priv->pos);
+			stm32_memcpy_32to16(&pcm_buff[priv->pos], src_buff,
+					    buff_size - priv->pos);
 		else
 			memcpy(&pcm_buff[priv->pos], src_buff,
 			       buff_size - priv->pos);
@@ -196,8 +196,8 @@ static int stm32_afsdm_pcm_cb(const void *data, size_t size, void *private)
 	}
 
 	if (format == SNDRV_PCM_FORMAT_S16_LE)
-		memcpy_32to16(&pcm_buff[priv->pos],
-			      &src_buff[src_size - cur_size], cur_size);
+		stm32_memcpy_32to16(&pcm_buff[priv->pos],
+				    &src_buff[src_size - cur_size], cur_size);
 	else
 		memcpy(&pcm_buff[priv->pos], &src_buff[src_size - cur_size],
 		       cur_size);
-- 
2.20.1

[PATCH AUTOSEL 5.4 046/107] ASoC: stm32: dfsdm: fix 16 bits record

[Sasha Levin]

From: Olivier Moysan <olivier.moysan@st.com>

[ Upstream commit 8e55ea19125b65cffe42747359af99d545e85f2f ]

In stm32_afsdm_pcm_cb function, the transfer size is provided in bytes.
However, samples are copied as 16 bits words from iio buffer.
Divide by two the transfer size, to copy the right number of samples.

Fixes: 1e7f6e1c69f0 ("ASoC: stm32: dfsdm: add 16 bits audio record support")

Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200110131131.3191-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/stm/stm32_adfsdm.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/sound/soc/stm/stm32_adfsdm.c b/sound/soc/stm/stm32_adfsdm.c
index 3c9a9deec9af4..4ecea4913f427 100644
--- a/sound/soc/stm/stm32_adfsdm.c
+++ b/sound/soc/stm/stm32_adfsdm.c
@@ -153,13 +153,13 @@ static const struct snd_soc_component_driver stm32_adfsdm_dai_component = {
 	.name = "stm32_dfsdm_audio",
 };
 
-static void memcpy_32to16(void *dest, const void *src, size_t n)
+static void stm32_memcpy_32to16(void *dest, const void *src, size_t n)
 {
 	unsigned int i = 0;
 	u16 *d = (u16 *)dest, *s = (u16 *)src;
 
 	s++;
-	for (i = n; i > 0; i--) {
+	for (i = n >> 1; i > 0; i--) {
 		*d++ = *s++;
 		s++;
 	}
@@ -186,8 +186,8 @@ static int stm32_afsdm_pcm_cb(const void *data, size_t size, void *private)
 
 	if ((priv->pos + src_size) > buff_size) {
 		if (format == SNDRV_PCM_FORMAT_S16_LE)
-			memcpy_32to16(&pcm_buff[priv->pos], src_buff,
-				      buff_size - priv->pos);
+			stm32_memcpy_32to16(&pcm_buff[priv->pos], src_buff,
+					    buff_size - priv->pos);
 		else
 			memcpy(&pcm_buff[priv->pos], src_buff,
 			       buff_size - priv->pos);
@@ -196,8 +196,8 @@ static int stm32_afsdm_pcm_cb(const void *data, size_t size, void *private)
 	}
 
 	if (format == SNDRV_PCM_FORMAT_S16_LE)
-		memcpy_32to16(&pcm_buff[priv->pos],
-			      &src_buff[src_size - cur_size], cur_size);
+		stm32_memcpy_32to16(&pcm_buff[priv->pos],
+				    &src_buff[src_size - cur_size], cur_size);
 	else
 		memcpy(&pcm_buff[priv->pos], &src_buff[src_size - cur_size],
 		       cur_size);
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[alsa-devel] [PATCH AUTOSEL 5.4 046/107] ASoC: stm32: dfsdm: fix 16 bits record

[Sasha Levin]

From: Olivier Moysan <olivier.moysan@st.com>

[ Upstream commit 8e55ea19125b65cffe42747359af99d545e85f2f ]

In stm32_afsdm_pcm_cb function, the transfer size is provided in bytes.
However, samples are copied as 16 bits words from iio buffer.
Divide by two the transfer size, to copy the right number of samples.

Fixes: 1e7f6e1c69f0 ("ASoC: stm32: dfsdm: add 16 bits audio record support")

Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200110131131.3191-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/stm/stm32_adfsdm.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/sound/soc/stm/stm32_adfsdm.c b/sound/soc/stm/stm32_adfsdm.c
index 3c9a9deec9af4..4ecea4913f427 100644
--- a/sound/soc/stm/stm32_adfsdm.c
+++ b/sound/soc/stm/stm32_adfsdm.c
@@ -153,13 +153,13 @@ static const struct snd_soc_component_driver stm32_adfsdm_dai_component = {
 	.name = "stm32_dfsdm_audio",
 };
 
-static void memcpy_32to16(void *dest, const void *src, size_t n)
+static void stm32_memcpy_32to16(void *dest, const void *src, size_t n)
 {
 	unsigned int i = 0;
 	u16 *d = (u16 *)dest, *s = (u16 *)src;
 
 	s++;
-	for (i = n; i > 0; i--) {
+	for (i = n >> 1; i > 0; i--) {
 		*d++ = *s++;
 		s++;
 	}
@@ -186,8 +186,8 @@ static int stm32_afsdm_pcm_cb(const void *data, size_t size, void *private)
 
 	if ((priv->pos + src_size) > buff_size) {
 		if (format == SNDRV_PCM_FORMAT_S16_LE)
-			memcpy_32to16(&pcm_buff[priv->pos], src_buff,
-				      buff_size - priv->pos);
+			stm32_memcpy_32to16(&pcm_buff[priv->pos], src_buff,
+					    buff_size - priv->pos);
 		else
 			memcpy(&pcm_buff[priv->pos], src_buff,
 			       buff_size - priv->pos);
@@ -196,8 +196,8 @@ static int stm32_afsdm_pcm_cb(const void *data, size_t size, void *private)
 	}
 
 	if (format == SNDRV_PCM_FORMAT_S16_LE)
-		memcpy_32to16(&pcm_buff[priv->pos],
-			      &src_buff[src_size - cur_size], cur_size);
+		stm32_memcpy_32to16(&pcm_buff[priv->pos],
+				    &src_buff[src_size - cur_size], cur_size);
 	else
 		memcpy(&pcm_buff[priv->pos], &src_buff[src_size - cur_size],
 		       cur_size);
-- 
2.20.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel

[PATCH AUTOSEL 5.4 047/107] net: bpf: Don't leak time wait and request sockets

[Sasha Levin]

From: Lorenz Bauer <lmb@cloudflare.com>

[ Upstream commit 2e012c74823629d9db27963c79caa3f5b2010746 ]

It's possible to leak time wait and request sockets via the following
BPF pseudo code:
 
  sk = bpf_skc_lookup_tcp(...)
  if (sk)
    bpf_sk_release(sk)

If sk->sk_state is TCP_NEW_SYN_RECV or TCP_TIME_WAIT the refcount taken
by bpf_skc_lookup_tcp is not undone by bpf_sk_release. This is because
sk_flags is re-used for other data in both kinds of sockets. The check

  !sock_flag(sk, SOCK_RCU_FREE)

therefore returns a bogus result. Check that sk_flags is valid by calling
sk_fullsock. Skip checking SOCK_RCU_FREE if we already know that sk is
not a full socket.

Fixes: edbf8c01de5a ("bpf: add skc_lookup_tcp helper")
Fixes: f7355a6c0497 ("bpf: Check sk_fullsock() before returning from bpf_sk_lookup()")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200110132336.26099-1-lmb@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/core/filter.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)

diff --git a/net/core/filter.c b/net/core/filter.c
index 2f76461c120d2..3cbf06a466f7d 100644
--- a/net/core/filter.c
+++ b/net/core/filter.c
@@ -5305,8 +5305,7 @@ __bpf_sk_lookup(struct sk_buff *skb, struct bpf_sock_tuple *tuple, u32 len,
 	if (sk) {
 		sk = sk_to_full_sk(sk);
 		if (!sk_fullsock(sk)) {
-			if (!sock_flag(sk, SOCK_RCU_FREE))
-				sock_gen_put(sk);
+			sock_gen_put(sk);
 			return NULL;
 		}
 	}
@@ -5343,8 +5342,7 @@ bpf_sk_lookup(struct sk_buff *skb, struct bpf_sock_tuple *tuple, u32 len,
 	if (sk) {
 		sk = sk_to_full_sk(sk);
 		if (!sk_fullsock(sk)) {
-			if (!sock_flag(sk, SOCK_RCU_FREE))
-				sock_gen_put(sk);
+			sock_gen_put(sk);
 			return NULL;
 		}
 	}
@@ -5411,7 +5409,8 @@ static const struct bpf_func_proto bpf_sk_lookup_udp_proto = {
 
 BPF_CALL_1(bpf_sk_release, struct sock *, sk)
 {
-	if (!sock_flag(sk, SOCK_RCU_FREE))
+	/* Only full sockets have sk->sk_flags. */
+	if (!sk_fullsock(sk) || !sock_flag(sk, SOCK_RCU_FREE))
 		sock_gen_put(sk);
 	return 0;
 }
-- 
2.20.1

[PATCH AUTOSEL 5.4 048/107] net: stmmac: selftests: Update status when disabling RSS

[Sasha Levin]

From: Jose Abreu <Jose.Abreu@synopsys.com>

[ Upstream commit e715d74504352968cf24ac95476706bc911a69cd ]

We are disabling RSS on HW but not updating the internal private status
to the 'disabled' state. This is needed for next tc commit that will
check if RSS is disabled before trying to apply filters.

Fixes: 4647e021193d ("net: stmmac: selftests: Add selftest for L3/L4 Filters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../stmicro/stmmac/stmmac_selftests.c         | 20 +++++++++++++------
 1 file changed, 14 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
index a0513deab1a04..3679d123a2ab7 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
@@ -1291,16 +1291,19 @@ static int __stmmac_test_l3filt(struct stmmac_priv *priv, u32 dst, u32 src,
 	struct stmmac_packet_attrs attr = { };
 	struct flow_dissector *dissector;
 	struct flow_cls_offload *cls;
+	int ret, old_enable = 0;
 	struct flow_rule *rule;
-	int ret;
 
 	if (!tc_can_offload(priv->dev))
 		return -EOPNOTSUPP;
 	if (!priv->dma_cap.l3l4fnum)
 		return -EOPNOTSUPP;
-	if (priv->rss.enable)
+	if (priv->rss.enable) {
+		old_enable = priv->rss.enable;
+		priv->rss.enable = false;
 		stmmac_rss_configure(priv, priv->hw, NULL,
 				     priv->plat->rx_queues_to_use);
+	}
 
 	dissector = kzalloc(sizeof(*dissector), GFP_KERNEL);
 	if (!dissector) {
@@ -1367,7 +1370,8 @@ cleanup_cls:
 cleanup_dissector:
 	kfree(dissector);
 cleanup_rss:
-	if (priv->rss.enable) {
+	if (old_enable) {
+		priv->rss.enable = old_enable;
 		stmmac_rss_configure(priv, priv->hw, &priv->rss,
 				     priv->plat->rx_queues_to_use);
 	}
@@ -1412,16 +1416,19 @@ static int __stmmac_test_l4filt(struct stmmac_priv *priv, u32 dst, u32 src,
 	struct stmmac_packet_attrs attr = { };
 	struct flow_dissector *dissector;
 	struct flow_cls_offload *cls;
+	int ret, old_enable = 0;
 	struct flow_rule *rule;
-	int ret;
 
 	if (!tc_can_offload(priv->dev))
 		return -EOPNOTSUPP;
 	if (!priv->dma_cap.l3l4fnum)
 		return -EOPNOTSUPP;
-	if (priv->rss.enable)
+	if (priv->rss.enable) {
+		old_enable = priv->rss.enable;
+		priv->rss.enable = false;
 		stmmac_rss_configure(priv, priv->hw, NULL,
 				     priv->plat->rx_queues_to_use);
+	}
 
 	dissector = kzalloc(sizeof(*dissector), GFP_KERNEL);
 	if (!dissector) {
@@ -1493,7 +1500,8 @@ cleanup_cls:
 cleanup_dissector:
 	kfree(dissector);
 cleanup_rss:
-	if (priv->rss.enable) {
+	if (old_enable) {
+		priv->rss.enable = old_enable;
 		stmmac_rss_configure(priv, priv->hw, &priv->rss,
 				     priv->plat->rx_queues_to_use);
 	}
-- 
2.20.1

[PATCH AUTOSEL 5.4 049/107] net: stmmac: tc: Do not setup flower filtering if RSS is enabled

[Sasha Levin]

From: Jose Abreu <Jose.Abreu@synopsys.com>

[ Upstream commit 7bd754c47dd3ad1b048c9641294b0234fcce2c58 ]

RSS, when enabled, will bypass the L3 and L4 filtering causing it not
to work. Add a check before trying to setup the filters.

Fixes: 425eabddaf0f ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
index f9a9a9d822333..1d135b02ea021 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
@@ -579,6 +579,10 @@ static int tc_setup_cls(struct stmmac_priv *priv,
 {
 	int ret = 0;
 
+	/* When RSS is enabled, the filtering will be bypassed */
+	if (priv->rss.enable)
+		return -EBUSY;
+
 	switch (cls->command) {
 	case FLOW_CLS_REPLACE:
 		ret = tc_add_flow(priv, cls);
-- 
2.20.1

[PATCH AUTOSEL 5.4 050/107] bpftool: Fix printing incorrect pointer in btf_dump_ptr

[Sasha Levin]

From: Martin KaFai Lau <kafai@fb.com>

[ Upstream commit 555089fdfc37ad65e0ee9b42ca40c238ff546f83 ]

For plain text output, it incorrectly prints the pointer value
"void *data".  The "void *data" is actually pointing to memory that
contains a bpf-map's value.  The intention is to print the content of
the bpf-map's value instead of printing the pointer pointing to the
bpf-map's value.

In this case, a member of the bpf-map's value is a pointer type.
Thus, it should print the "*(void **)data".

Fixes: 22c349e8db89 ("tools: bpftool: fix format strings and arguments for jsonw_printf()")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Link: https://lore.kernel.org/bpf/20200110231644.3484151-1-kafai@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/bpf/bpftool/btf_dumper.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/tools/bpf/bpftool/btf_dumper.c b/tools/bpf/bpftool/btf_dumper.c
index d66131f696892..397e5716ab6d8 100644
--- a/tools/bpf/bpftool/btf_dumper.c
+++ b/tools/bpf/bpftool/btf_dumper.c
@@ -26,7 +26,7 @@ static void btf_dumper_ptr(const void *data, json_writer_t *jw,
 			   bool is_plain_text)
 {
 	if (is_plain_text)
-		jsonw_printf(jw, "%p", data);
+		jsonw_printf(jw, "%p", *(void **)data);
 	else
 		jsonw_printf(jw, "%lu", *(unsigned long *)data);
 }
-- 
2.20.1

[PATCH AUTOSEL 5.4 051/107] platform/x86: GPD pocket fan: Allow somewhat lower/higher temperature limits

[Sasha Levin]

From: Hans de Goede <hdegoede@redhat.com>

[ Upstream commit 1f27dbd8265dbb379926c8f6a4453fe7fe26d7a3 ]

Allow the user to configure the fan to turn on / speed-up at lower
thresholds then before (20 degrees Celcius as minimum instead of 40) and
likewise also allow the user to delay the fan speeding-up till the
temperature hits 90 degrees Celcius (was 70).

Cc: Jason Anderson <jasona.594@gmail.com>
Reported-by: Jason Anderson <jasona.594@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/gpd-pocket-fan.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/platform/x86/gpd-pocket-fan.c b/drivers/platform/x86/gpd-pocket-fan.c
index 73eb1572b9662..b471b86c28fe8 100644
--- a/drivers/platform/x86/gpd-pocket-fan.c
+++ b/drivers/platform/x86/gpd-pocket-fan.c
@@ -127,7 +127,7 @@ static int gpd_pocket_fan_probe(struct platform_device *pdev)
 	int i;
 
 	for (i = 0; i < ARRAY_SIZE(temp_limits); i++) {
-		if (temp_limits[i] < 40000 || temp_limits[i] > 70000) {
+		if (temp_limits[i] < 20000 || temp_limits[i] > 90000) {
 			dev_err(&pdev->dev, "Invalid temp-limit %d (must be between 40000 and 70000)\n",
 				temp_limits[i]);
 			temp_limits[0] = TEMP_LIMIT0_DEFAULT;
-- 
2.20.1

[PATCH AUTOSEL 5.4 052/107] platform/x86: intel_pmc_core: update Comet Lake platform driver

[Sasha Levin]

From: Harry Pan <harry.pan@intel.com>

[ Upstream commit 515ff674bb9bf06186052e352c4587dab8defaf0 ]

Adding new CML CPU model ID into platform driver support list.

Signed-off-by: Harry Pan <harry.pan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/intel_pmc_core_pltdrv.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/platform/x86/intel_pmc_core_pltdrv.c b/drivers/platform/x86/intel_pmc_core_pltdrv.c
index 6fe829f30997d..e1266f5c63593 100644
--- a/drivers/platform/x86/intel_pmc_core_pltdrv.c
+++ b/drivers/platform/x86/intel_pmc_core_pltdrv.c
@@ -44,6 +44,8 @@ static const struct x86_cpu_id intel_pmc_core_platform_ids[] = {
 	INTEL_CPU_FAM6(KABYLAKE, pmc_core_device),
 	INTEL_CPU_FAM6(CANNONLAKE_L, pmc_core_device),
 	INTEL_CPU_FAM6(ICELAKE_L, pmc_core_device),
+	INTEL_CPU_FAM6(COMETLAKE, pmc_core_device),
+	INTEL_CPU_FAM6(COMETLAKE_L, pmc_core_device),
 	{}
 };
 MODULE_DEVICE_TABLE(x86cpu, intel_pmc_core_platform_ids);
-- 
2.20.1

[PATCH AUTOSEL 5.4 053/107] ASoC: SOF: Intel: fix HDA codec driver probe with multiple controllers

[Sasha Levin]

From: Kai Vehmanen <kai.vehmanen@linux.intel.com>

[ Upstream commit 2c63bea714780f8e1fc9cb7bc10deda26fada25b ]

In case system has multiple HDA controllers, it can happen that
same HDA codec driver is used for codecs of multiple controllers.
In this case, SOF may fail to probe the HDA driver and SOF
initialization fails.

SOF HDA code currently relies that a call to request_module() will
also run device matching logic to attach driver to the codec instance.
However if driver for another HDA controller was already loaded and it
already loaded the HDA codec driver, this breaks current logic in SOF.
In this case the request_module() SOF does becomes a no-op and HDA
Codec driver is not attached to the codec instance sitting on the HDA
bus SOF is controlling. Typical scenario would be a system with both
external and internal GPUs, with driver of the external GPU loaded
first.

Fix this by adding similar logic as is used in legacy HDA driver
where an explicit device_attach() call is done after request_module().

Also add logic to propagate errors reported by device_attach() back
to caller. This also works in the case where drivers are not built
as modules.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/sof/intel/hda-codec.c | 19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)

diff --git a/sound/soc/sof/intel/hda-codec.c b/sound/soc/sof/intel/hda-codec.c
index 3ca6795a89ba3..9e8233c10d860 100644
--- a/sound/soc/sof/intel/hda-codec.c
+++ b/sound/soc/sof/intel/hda-codec.c
@@ -24,19 +24,18 @@
 #define IDISP_VID_INTEL	0x80860000
 
 /* load the legacy HDA codec driver */
-#ifdef MODULE
-static void hda_codec_load_module(struct hda_codec *codec)
+static int hda_codec_load_module(struct hda_codec *codec)
 {
+#ifdef MODULE
 	char alias[MODULE_NAME_LEN];
 	const char *module = alias;
 
 	snd_hdac_codec_modalias(&codec->core, alias, sizeof(alias));
 	dev_dbg(&codec->core.dev, "loading codec module: %s\n", module);
 	request_module(module);
-}
-#else
-static void hda_codec_load_module(struct hda_codec *codec) {}
 #endif
+	return device_attach(hda_codec_dev(codec));
+}
 
 /* enable controller wake up event for all codecs with jack connectors */
 void hda_codec_jack_wake_enable(struct snd_sof_dev *sdev)
@@ -116,10 +115,16 @@ static int hda_codec_probe(struct snd_sof_dev *sdev, int address)
 	/* use legacy bus only for HDA codecs, idisp uses ext bus */
 	if ((resp & 0xFFFF0000) != IDISP_VID_INTEL) {
 		hdev->type = HDA_DEV_LEGACY;
-		hda_codec_load_module(&hda_priv->codec);
+		ret = hda_codec_load_module(&hda_priv->codec);
+		/*
+		 * handle ret==0 (no driver bound) as an error, but pass
+		 * other return codes without modification
+		 */
+		if (ret == 0)
+			ret = -ENOENT;
 	}
 
-	return 0;
+	return ret;
 #else
 	hdev = devm_kzalloc(sdev->dev, sizeof(*hdev), GFP_KERNEL);
 	if (!hdev)
-- 
2.20.1

[alsa-devel] [PATCH AUTOSEL 5.4 053/107] ASoC: SOF: Intel: fix HDA codec driver probe with multiple controllers

[Sasha Levin]

From: Kai Vehmanen <kai.vehmanen@linux.intel.com>

[ Upstream commit 2c63bea714780f8e1fc9cb7bc10deda26fada25b ]

In case system has multiple HDA controllers, it can happen that
same HDA codec driver is used for codecs of multiple controllers.
In this case, SOF may fail to probe the HDA driver and SOF
initialization fails.

SOF HDA code currently relies that a call to request_module() will
also run device matching logic to attach driver to the codec instance.
However if driver for another HDA controller was already loaded and it
already loaded the HDA codec driver, this breaks current logic in SOF.
In this case the request_module() SOF does becomes a no-op and HDA
Codec driver is not attached to the codec instance sitting on the HDA
bus SOF is controlling. Typical scenario would be a system with both
external and internal GPUs, with driver of the external GPU loaded
first.

Fix this by adding similar logic as is used in legacy HDA driver
where an explicit device_attach() call is done after request_module().

Also add logic to propagate errors reported by device_attach() back
to caller. This also works in the case where drivers are not built
as modules.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/sof/intel/hda-codec.c | 19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)

diff --git a/sound/soc/sof/intel/hda-codec.c b/sound/soc/sof/intel/hda-codec.c
index 3ca6795a89ba3..9e8233c10d860 100644
--- a/sound/soc/sof/intel/hda-codec.c
+++ b/sound/soc/sof/intel/hda-codec.c
@@ -24,19 +24,18 @@
 #define IDISP_VID_INTEL	0x80860000
 
 /* load the legacy HDA codec driver */
-#ifdef MODULE
-static void hda_codec_load_module(struct hda_codec *codec)
+static int hda_codec_load_module(struct hda_codec *codec)
 {
+#ifdef MODULE
 	char alias[MODULE_NAME_LEN];
 	const char *module = alias;
 
 	snd_hdac_codec_modalias(&codec->core, alias, sizeof(alias));
 	dev_dbg(&codec->core.dev, "loading codec module: %s\n", module);
 	request_module(module);
-}
-#else
-static void hda_codec_load_module(struct hda_codec *codec) {}
 #endif
+	return device_attach(hda_codec_dev(codec));
+}
 
 /* enable controller wake up event for all codecs with jack connectors */
 void hda_codec_jack_wake_enable(struct snd_sof_dev *sdev)
@@ -116,10 +115,16 @@ static int hda_codec_probe(struct snd_sof_dev *sdev, int address)
 	/* use legacy bus only for HDA codecs, idisp uses ext bus */
 	if ((resp & 0xFFFF0000) != IDISP_VID_INTEL) {
 		hdev->type = HDA_DEV_LEGACY;
-		hda_codec_load_module(&hda_priv->codec);
+		ret = hda_codec_load_module(&hda_priv->codec);
+		/*
+		 * handle ret==0 (no driver bound) as an error, but pass
+		 * other return codes without modification
+		 */
+		if (ret == 0)
+			ret = -ENOENT;
 	}
 
-	return 0;
+	return ret;
 #else
 	hdev = devm_kzalloc(sdev->dev, sizeof(*hdev), GFP_KERNEL);
 	if (!hdev)
-- 
2.20.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel

[PATCH AUTOSEL 5.4 054/107] ASoC: hdac_hda: Fix error in driver removal after failed probe

[Sasha Levin]

From: Kai Vehmanen <kai.vehmanen@linux.intel.com>

[ Upstream commit 552b1a85da9f63856e7e341b81c16e0e078204f1 ]

In case system has multiple HDA codecs, and codec probe fails for
at least one but not all codecs, driver will end up cancelling
a non-initialized timer context upon driver removal.

Call trace of typical case:

[   60.593646] WARNING: CPU: 1 PID: 1147 at kernel/workqueue.c:3032
__flush_work+0x18b/0x1a0
[...]
[   60.593670]  __cancel_work_timer+0x11f/0x1a0
[   60.593673]  hdac_hda_dev_remove+0x25/0x30 [snd_soc_hdac_hda]
[   60.593674]  device_release_driver_internal+0xe0/0x1c0
[   60.593675]  bus_remove_device+0xd6/0x140
[   60.593677]  device_del+0x175/0x3e0
[   60.593679]  ? widget_tree_free.isra.7+0x90/0xb0 [snd_hda_core]
[   60.593680]  snd_hdac_device_unregister+0x34/0x50 [snd_hda_core]
[   60.593682]  snd_hdac_ext_bus_device_remove+0x2a/0x60 [snd_hda_ext_core]
[   60.593684]  hda_dsp_remove+0x26/0x100 [snd_sof_intel_hda_common]
[   60.593686]  snd_sof_device_remove+0x84/0xa0 [snd_sof]
[   60.593687]  sof_pci_remove+0x10/0x30 [snd_sof_pci]
[   60.593689]  pci_device_remove+0x36/0xb0

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/hdac_hda.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/sound/soc/codecs/hdac_hda.c b/sound/soc/codecs/hdac_hda.c
index 4570f662fb48b..d78f4d856aaff 100644
--- a/sound/soc/codecs/hdac_hda.c
+++ b/sound/soc/codecs/hdac_hda.c
@@ -498,7 +498,9 @@ static int hdac_hda_dev_remove(struct hdac_device *hdev)
 	struct hdac_hda_priv *hda_pvt;
 
 	hda_pvt = dev_get_drvdata(&hdev->dev);
-	cancel_delayed_work_sync(&hda_pvt->codec.jackpoll_work);
+	if (hda_pvt && hda_pvt->codec.registered)
+		cancel_delayed_work_sync(&hda_pvt->codec.jackpoll_work);
+
 	return 0;
 }
 
-- 
2.20.1

[alsa-devel] [PATCH AUTOSEL 5.4 054/107] ASoC: hdac_hda: Fix error in driver removal after failed probe

[Sasha Levin]

From: Kai Vehmanen <kai.vehmanen@linux.intel.com>

[ Upstream commit 552b1a85da9f63856e7e341b81c16e0e078204f1 ]

In case system has multiple HDA codecs, and codec probe fails for
at least one but not all codecs, driver will end up cancelling
a non-initialized timer context upon driver removal.

Call trace of typical case:

[   60.593646] WARNING: CPU: 1 PID: 1147 at kernel/workqueue.c:3032
__flush_work+0x18b/0x1a0
[...]
[   60.593670]  __cancel_work_timer+0x11f/0x1a0
[   60.593673]  hdac_hda_dev_remove+0x25/0x30 [snd_soc_hdac_hda]
[   60.593674]  device_release_driver_internal+0xe0/0x1c0
[   60.593675]  bus_remove_device+0xd6/0x140
[   60.593677]  device_del+0x175/0x3e0
[   60.593679]  ? widget_tree_free.isra.7+0x90/0xb0 [snd_hda_core]
[   60.593680]  snd_hdac_device_unregister+0x34/0x50 [snd_hda_core]
[   60.593682]  snd_hdac_ext_bus_device_remove+0x2a/0x60 [snd_hda_ext_core]
[   60.593684]  hda_dsp_remove+0x26/0x100 [snd_sof_intel_hda_common]
[   60.593686]  snd_sof_device_remove+0x84/0xa0 [snd_sof]
[   60.593687]  sof_pci_remove+0x10/0x30 [snd_sof_pci]
[   60.593689]  pci_device_remove+0x36/0xb0

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/hdac_hda.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/sound/soc/codecs/hdac_hda.c b/sound/soc/codecs/hdac_hda.c
index 4570f662fb48b..d78f4d856aaff 100644
--- a/sound/soc/codecs/hdac_hda.c
+++ b/sound/soc/codecs/hdac_hda.c
@@ -498,7 +498,9 @@ static int hdac_hda_dev_remove(struct hdac_device *hdev)
 	struct hdac_hda_priv *hda_pvt;
 
 	hda_pvt = dev_get_drvdata(&hdev->dev);
-	cancel_delayed_work_sync(&hda_pvt->codec.jackpoll_work);
+	if (hda_pvt && hda_pvt->codec.registered)
+		cancel_delayed_work_sync(&hda_pvt->codec.jackpoll_work);
+
 	return 0;
 }
 
-- 
2.20.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel

[PATCH AUTOSEL 5.4 055/107] ASoC: msm8916-wcd-analog: Fix selected events for MIC BIAS External1

[Sasha Levin]

From: Stephan Gerhold <stephan@gerhold.net>

[ Upstream commit e0beec88397b163c7c4ea6fcfb67e8e07a2671dc ]

MIC BIAS External1 sets pm8916_wcd_analog_enable_micbias_ext1()
as event handler, which ends up in pm8916_wcd_analog_enable_micbias_ext().

But pm8916_wcd_analog_enable_micbias_ext() only handles the POST_PMU
event, which is not specified in the event flags for MIC BIAS External1.
This means that the code in the event handler is never actually run.

Set SND_SOC_DAPM_POST_PMU as the only event for the handler to fix this.

Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/msm8916-wcd-analog.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/sound/soc/codecs/msm8916-wcd-analog.c b/sound/soc/codecs/msm8916-wcd-analog.c
index e3d311fb510e0..08399a734be27 100644
--- a/sound/soc/codecs/msm8916-wcd-analog.c
+++ b/sound/soc/codecs/msm8916-wcd-analog.c
@@ -888,10 +888,10 @@ static const struct snd_soc_dapm_widget pm8916_wcd_analog_dapm_widgets[] = {
 
 	SND_SOC_DAPM_SUPPLY("MIC BIAS External1", CDC_A_MICB_1_EN, 7, 0,
 			    pm8916_wcd_analog_enable_micbias_ext1,
-			    SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
+			    SND_SOC_DAPM_POST_PMU),
 	SND_SOC_DAPM_SUPPLY("MIC BIAS External2", CDC_A_MICB_2_EN, 7, 0,
 			    pm8916_wcd_analog_enable_micbias_ext2,
-			    SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD),
+			    SND_SOC_DAPM_POST_PMU),
 
 	SND_SOC_DAPM_ADC_E("ADC1", NULL, CDC_A_TX_1_EN, 7, 0,
 			   pm8916_wcd_analog_enable_adc,
-- 
2.20.1

[alsa-devel] [PATCH AUTOSEL 5.4 055/107] ASoC: msm8916-wcd-analog: Fix selected events for MIC BIAS External1

[Sasha Levin]

From: Stephan Gerhold <stephan@gerhold.net>

[ Upstream commit e0beec88397b163c7c4ea6fcfb67e8e07a2671dc ]

MIC BIAS External1 sets pm8916_wcd_analog_enable_micbias_ext1()
as event handler, which ends up in pm8916_wcd_analog_enable_micbias_ext().

But pm8916_wcd_analog_enable_micbias_ext() only handles the POST_PMU
event, which is not specified in the event flags for MIC BIAS External1.
This means that the code in the event handler is never actually run.

Set SND_SOC_DAPM_POST_PMU as the only event for the handler to fix this.

Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/msm8916-wcd-analog.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/sound/soc/codecs/msm8916-wcd-analog.c b/sound/soc/codecs/msm8916-wcd-analog.c
index e3d311fb510e0..08399a734be27 100644
--- a/sound/soc/codecs/msm8916-wcd-analog.c
+++ b/sound/soc/codecs/msm8916-wcd-analog.c
@@ -888,10 +888,10 @@ static const struct snd_soc_dapm_widget pm8916_wcd_analog_dapm_widgets[] = {
 
 	SND_SOC_DAPM_SUPPLY("MIC BIAS External1", CDC_A_MICB_1_EN, 7, 0,
 			    pm8916_wcd_analog_enable_micbias_ext1,
-			    SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
+			    SND_SOC_DAPM_POST_PMU),
 	SND_SOC_DAPM_SUPPLY("MIC BIAS External2", CDC_A_MICB_2_EN, 7, 0,
 			    pm8916_wcd_analog_enable_micbias_ext2,
-			    SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD),
+			    SND_SOC_DAPM_POST_PMU),
 
 	SND_SOC_DAPM_ADC_E("ADC1", NULL, CDC_A_TX_1_EN, 7, 0,
 			   pm8916_wcd_analog_enable_adc,
-- 
2.20.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel

[PATCH AUTOSEL 5.4 056/107] ASoC: sti: fix possible sleep-in-atomic

[Sasha Levin]

From: Arnaud Pouliquen <arnaud.pouliquen@st.com>

[ Upstream commit ce780a47c3c01e1e179d0792df6b853a913928f1 ]

Change mutex and spinlock management to avoid sleep
in atomic issue.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200113100400.30472-1-arnaud.pouliquen@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/sti/uniperif_player.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/sound/soc/sti/uniperif_player.c b/sound/soc/sti/uniperif_player.c
index 48ea915b24ba2..2ed92c990b97c 100644
--- a/sound/soc/sti/uniperif_player.c
+++ b/sound/soc/sti/uniperif_player.c
@@ -226,7 +226,6 @@ static void uni_player_set_channel_status(struct uniperif *player,
 	 * sampling frequency. If no sample rate is already specified, then
 	 * set one.
 	 */
-	mutex_lock(&player->ctrl_lock);
 	if (runtime) {
 		switch (runtime->rate) {
 		case 22050:
@@ -303,7 +302,6 @@ static void uni_player_set_channel_status(struct uniperif *player,
 		player->stream_settings.iec958.status[3 + (n * 4)] << 24;
 		SET_UNIPERIF_CHANNEL_STA_REGN(player, n, status);
 	}
-	mutex_unlock(&player->ctrl_lock);
 
 	/* Update the channel status */
 	if (player->ver < SND_ST_UNIPERIF_VERSION_UNI_PLR_TOP_1_0)
@@ -365,8 +363,10 @@ static int uni_player_prepare_iec958(struct uniperif *player,
 
 	SET_UNIPERIF_CTRL_ZERO_STUFF_HW(player);
 
+	mutex_lock(&player->ctrl_lock);
 	/* Update the channel status */
 	uni_player_set_channel_status(player, runtime);
+	mutex_unlock(&player->ctrl_lock);
 
 	/* Clear the user validity user bits */
 	SET_UNIPERIF_USER_VALIDITY_VALIDITY_LR(player, 0);
@@ -598,7 +598,6 @@ static int uni_player_ctl_iec958_put(struct snd_kcontrol *kcontrol,
 	iec958->status[1] = ucontrol->value.iec958.status[1];
 	iec958->status[2] = ucontrol->value.iec958.status[2];
 	iec958->status[3] = ucontrol->value.iec958.status[3];
-	mutex_unlock(&player->ctrl_lock);
 
 	spin_lock_irqsave(&player->irq_lock, flags);
 	if (player->substream && player->substream->runtime)
@@ -608,6 +607,8 @@ static int uni_player_ctl_iec958_put(struct snd_kcontrol *kcontrol,
 		uni_player_set_channel_status(player, NULL);
 
 	spin_unlock_irqrestore(&player->irq_lock, flags);
+	mutex_unlock(&player->ctrl_lock);
+
 	return 0;
 }
 
-- 
2.20.1

[alsa-devel] [PATCH AUTOSEL 5.4 056/107] ASoC: sti: fix possible sleep-in-atomic

[Sasha Levin]

From: Arnaud Pouliquen <arnaud.pouliquen@st.com>

[ Upstream commit ce780a47c3c01e1e179d0792df6b853a913928f1 ]

Change mutex and spinlock management to avoid sleep
in atomic issue.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200113100400.30472-1-arnaud.pouliquen@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/sti/uniperif_player.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/sound/soc/sti/uniperif_player.c b/sound/soc/sti/uniperif_player.c
index 48ea915b24ba2..2ed92c990b97c 100644
--- a/sound/soc/sti/uniperif_player.c
+++ b/sound/soc/sti/uniperif_player.c
@@ -226,7 +226,6 @@ static void uni_player_set_channel_status(struct uniperif *player,
 	 * sampling frequency. If no sample rate is already specified, then
 	 * set one.
 	 */
-	mutex_lock(&player->ctrl_lock);
 	if (runtime) {
 		switch (runtime->rate) {
 		case 22050:
@@ -303,7 +302,6 @@ static void uni_player_set_channel_status(struct uniperif *player,
 		player->stream_settings.iec958.status[3 + (n * 4)] << 24;
 		SET_UNIPERIF_CHANNEL_STA_REGN(player, n, status);
 	}
-	mutex_unlock(&player->ctrl_lock);
 
 	/* Update the channel status */
 	if (player->ver < SND_ST_UNIPERIF_VERSION_UNI_PLR_TOP_1_0)
@@ -365,8 +363,10 @@ static int uni_player_prepare_iec958(struct uniperif *player,
 
 	SET_UNIPERIF_CTRL_ZERO_STUFF_HW(player);
 
+	mutex_lock(&player->ctrl_lock);
 	/* Update the channel status */
 	uni_player_set_channel_status(player, runtime);
+	mutex_unlock(&player->ctrl_lock);
 
 	/* Clear the user validity user bits */
 	SET_UNIPERIF_USER_VALIDITY_VALIDITY_LR(player, 0);
@@ -598,7 +598,6 @@ static int uni_player_ctl_iec958_put(struct snd_kcontrol *kcontrol,
 	iec958->status[1] = ucontrol->value.iec958.status[1];
 	iec958->status[2] = ucontrol->value.iec958.status[2];
 	iec958->status[3] = ucontrol->value.iec958.status[3];
-	mutex_unlock(&player->ctrl_lock);
 
 	spin_lock_irqsave(&player->irq_lock, flags);
 	if (player->substream && player->substream->runtime)
@@ -608,6 +607,8 @@ static int uni_player_ctl_iec958_put(struct snd_kcontrol *kcontrol,
 		uni_player_set_channel_status(player, NULL);
 
 	spin_unlock_irqrestore(&player->irq_lock, flags);
+	mutex_unlock(&player->ctrl_lock);
+
 	return 0;
 }
 
-- 
2.20.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel

[PATCH AUTOSEL 5.4 057/107] ASoC: msm8916-wcd-analog: Fix MIC BIAS Internal1

[Sasha Levin]

From: Stephan Gerhold <stephan@gerhold.net>

[ Upstream commit 057efcf9faea4769cf1020677d93d040db9b23f3 ]

MIC BIAS Internal1 is broken at the moment because we always
enable the internal rbias resistor to the TX2 line (connected to
the headset microphone), rather than enabling the resistor connected
to TX1.

Move the RBIAS code to pm8916_wcd_analog_enable_micbias_int1/2()
to fix this.

Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/msm8916-wcd-analog.c | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)

diff --git a/sound/soc/codecs/msm8916-wcd-analog.c b/sound/soc/codecs/msm8916-wcd-analog.c
index 08399a734be27..84289ebeae872 100644
--- a/sound/soc/codecs/msm8916-wcd-analog.c
+++ b/sound/soc/codecs/msm8916-wcd-analog.c
@@ -391,9 +391,6 @@ static int pm8916_wcd_analog_enable_micbias_int(struct snd_soc_component
 
 	switch (event) {
 	case SND_SOC_DAPM_PRE_PMU:
-		snd_soc_component_update_bits(component, CDC_A_MICB_1_INT_RBIAS,
-				    MICB_1_INT_TX2_INT_RBIAS_EN_MASK,
-				    MICB_1_INT_TX2_INT_RBIAS_EN_ENABLE);
 		snd_soc_component_update_bits(component, reg, MICB_1_EN_PULL_DOWN_EN_MASK, 0);
 		snd_soc_component_update_bits(component, CDC_A_MICB_1_EN,
 				    MICB_1_EN_OPA_STG2_TAIL_CURR_MASK,
@@ -443,6 +440,14 @@ static int pm8916_wcd_analog_enable_micbias_int1(struct
 	struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
 	struct pm8916_wcd_analog_priv *wcd = snd_soc_component_get_drvdata(component);
 
+	switch (event) {
+	case SND_SOC_DAPM_PRE_PMU:
+		snd_soc_component_update_bits(component, CDC_A_MICB_1_INT_RBIAS,
+				    MICB_1_INT_TX1_INT_RBIAS_EN_MASK,
+				    MICB_1_INT_TX1_INT_RBIAS_EN_ENABLE);
+		break;
+	}
+
 	return pm8916_wcd_analog_enable_micbias_int(component, event, w->reg,
 						     wcd->micbias1_cap_mode);
 }
@@ -553,6 +558,11 @@ static int pm8916_wcd_analog_enable_micbias_int2(struct
 	struct pm8916_wcd_analog_priv *wcd = snd_soc_component_get_drvdata(component);
 
 	switch (event) {
+	case SND_SOC_DAPM_PRE_PMU:
+		snd_soc_component_update_bits(component, CDC_A_MICB_1_INT_RBIAS,
+				    MICB_1_INT_TX2_INT_RBIAS_EN_MASK,
+				    MICB_1_INT_TX2_INT_RBIAS_EN_ENABLE);
+		break;
 	case SND_SOC_DAPM_POST_PMU:
 		pm8916_mbhc_configure_bias(wcd, true);
 		break;
-- 
2.20.1

[alsa-devel] [PATCH AUTOSEL 5.4 057/107] ASoC: msm8916-wcd-analog: Fix MIC BIAS Internal1

[Sasha Levin]

From: Stephan Gerhold <stephan@gerhold.net>

[ Upstream commit 057efcf9faea4769cf1020677d93d040db9b23f3 ]

MIC BIAS Internal1 is broken at the moment because we always
enable the internal rbias resistor to the TX2 line (connected to
the headset microphone), rather than enabling the resistor connected
to TX1.

Move the RBIAS code to pm8916_wcd_analog_enable_micbias_int1/2()
to fix this.

Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/msm8916-wcd-analog.c | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)

diff --git a/sound/soc/codecs/msm8916-wcd-analog.c b/sound/soc/codecs/msm8916-wcd-analog.c
index 08399a734be27..84289ebeae872 100644
--- a/sound/soc/codecs/msm8916-wcd-analog.c
+++ b/sound/soc/codecs/msm8916-wcd-analog.c
@@ -391,9 +391,6 @@ static int pm8916_wcd_analog_enable_micbias_int(struct snd_soc_component
 
 	switch (event) {
 	case SND_SOC_DAPM_PRE_PMU:
-		snd_soc_component_update_bits(component, CDC_A_MICB_1_INT_RBIAS,
-				    MICB_1_INT_TX2_INT_RBIAS_EN_MASK,
-				    MICB_1_INT_TX2_INT_RBIAS_EN_ENABLE);
 		snd_soc_component_update_bits(component, reg, MICB_1_EN_PULL_DOWN_EN_MASK, 0);
 		snd_soc_component_update_bits(component, CDC_A_MICB_1_EN,
 				    MICB_1_EN_OPA_STG2_TAIL_CURR_MASK,
@@ -443,6 +440,14 @@ static int pm8916_wcd_analog_enable_micbias_int1(struct
 	struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
 	struct pm8916_wcd_analog_priv *wcd = snd_soc_component_get_drvdata(component);
 
+	switch (event) {
+	case SND_SOC_DAPM_PRE_PMU:
+		snd_soc_component_update_bits(component, CDC_A_MICB_1_INT_RBIAS,
+				    MICB_1_INT_TX1_INT_RBIAS_EN_MASK,
+				    MICB_1_INT_TX1_INT_RBIAS_EN_ENABLE);
+		break;
+	}
+
 	return pm8916_wcd_analog_enable_micbias_int(component, event, w->reg,
 						     wcd->micbias1_cap_mode);
 }
@@ -553,6 +558,11 @@ static int pm8916_wcd_analog_enable_micbias_int2(struct
 	struct pm8916_wcd_analog_priv *wcd = snd_soc_component_get_drvdata(component);
 
 	switch (event) {
+	case SND_SOC_DAPM_PRE_PMU:
+		snd_soc_component_update_bits(component, CDC_A_MICB_1_INT_RBIAS,
+				    MICB_1_INT_TX2_INT_RBIAS_EN_MASK,
+				    MICB_1_INT_TX2_INT_RBIAS_EN_ENABLE);
+		break;
 	case SND_SOC_DAPM_POST_PMU:
 		pm8916_mbhc_configure_bias(wcd, true);
 		break;
-- 
2.20.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel

[PATCH AUTOSEL 5.4 058/107] ASoC: msm8916-wcd-digital: Reset RX interpolation path after use

[Sasha Levin]

From: Stephan Gerhold <stephan@gerhold.net>

[ Upstream commit 85578bbd642f65065039b1765ebe1a867d5435b0 ]

For some reason, attempting to route audio through QDSP6 on MSM8916
causes the RX interpolation path to get "stuck" after playing audio
a few times. In this situation, the analog codec part is still working,
but the RX path in the digital codec stops working, so you only hear
the analog parts powering up. After a reboot everything works again.

So far I was not able to reproduce the problem when using lpass-cpu.

The downstream kernel driver avoids this by resetting the RX
interpolation path after use. In mainline we do something similar
for the TX decimator (LPASS_CDC_CLK_TX_RESET_B1_CTL), but the
interpolator reset (LPASS_CDC_CLK_RX_RESET_CTL) got lost when the
msm8916-wcd driver was split into analog and digital.

Fix this problem by adding the reset to
msm8916_wcd_digital_enable_interpolator().

Fixes: 150db8c5afa1 ("ASoC: codecs: Add msm8916-wcd digital codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200105102753.83108-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/msm8916-wcd-digital.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/sound/soc/codecs/msm8916-wcd-digital.c b/sound/soc/codecs/msm8916-wcd-digital.c
index 58b2468fb2a71..09fccacadd6b1 100644
--- a/sound/soc/codecs/msm8916-wcd-digital.c
+++ b/sound/soc/codecs/msm8916-wcd-digital.c
@@ -586,6 +586,12 @@ static int msm8916_wcd_digital_enable_interpolator(
 		snd_soc_component_write(component, rx_gain_reg[w->shift],
 			      snd_soc_component_read32(component, rx_gain_reg[w->shift]));
 		break;
+	case SND_SOC_DAPM_POST_PMD:
+		snd_soc_component_update_bits(component, LPASS_CDC_CLK_RX_RESET_CTL,
+					      1 << w->shift, 1 << w->shift);
+		snd_soc_component_update_bits(component, LPASS_CDC_CLK_RX_RESET_CTL,
+					      1 << w->shift, 0x0);
+		break;
 	}
 	return 0;
 }
-- 
2.20.1

[alsa-devel] [PATCH AUTOSEL 5.4 058/107] ASoC: msm8916-wcd-digital: Reset RX interpolation path after use

[Sasha Levin]

From: Stephan Gerhold <stephan@gerhold.net>

[ Upstream commit 85578bbd642f65065039b1765ebe1a867d5435b0 ]

For some reason, attempting to route audio through QDSP6 on MSM8916
causes the RX interpolation path to get "stuck" after playing audio
a few times. In this situation, the analog codec part is still working,
but the RX path in the digital codec stops working, so you only hear
the analog parts powering up. After a reboot everything works again.

So far I was not able to reproduce the problem when using lpass-cpu.

The downstream kernel driver avoids this by resetting the RX
interpolation path after use. In mainline we do something similar
for the TX decimator (LPASS_CDC_CLK_TX_RESET_B1_CTL), but the
interpolator reset (LPASS_CDC_CLK_RX_RESET_CTL) got lost when the
msm8916-wcd driver was split into analog and digital.

Fix this problem by adding the reset to
msm8916_wcd_digital_enable_interpolator().

Fixes: 150db8c5afa1 ("ASoC: codecs: Add msm8916-wcd digital codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200105102753.83108-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/msm8916-wcd-digital.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/sound/soc/codecs/msm8916-wcd-digital.c b/sound/soc/codecs/msm8916-wcd-digital.c
index 58b2468fb2a71..09fccacadd6b1 100644
--- a/sound/soc/codecs/msm8916-wcd-digital.c
+++ b/sound/soc/codecs/msm8916-wcd-digital.c
@@ -586,6 +586,12 @@ static int msm8916_wcd_digital_enable_interpolator(
 		snd_soc_component_write(component, rx_gain_reg[w->shift],
 			      snd_soc_component_read32(component, rx_gain_reg[w->shift]));
 		break;
+	case SND_SOC_DAPM_POST_PMD:
+		snd_soc_component_update_bits(component, LPASS_CDC_CLK_RX_RESET_CTL,
+					      1 << w->shift, 1 << w->shift);
+		snd_soc_component_update_bits(component, LPASS_CDC_CLK_RX_RESET_CTL,
+					      1 << w->shift, 0x0);
+		break;
 	}
 	return 0;
 }
-- 
2.20.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel

[PATCH AUTOSEL 5.4 059/107] netfilter: fix a use-after-free in mtype_destroy()

[Sasha Levin]

From: Cong Wang <xiyou.wangcong@gmail.com>

[ Upstream commit c120959387efa51479056fd01dc90adfba7a590c ]

map->members is freed by ip_set_free() right before using it in
mtype_ext_cleanup() again. So we just have to move it down.

Reported-by: syzbot+4c3cc6dbe7259dbf9054@syzkaller.appspotmail.com
Fixes: 40cd63bf33b2 ("netfilter: ipset: Support extensions which need a per data destroy function")
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/ipset/ip_set_bitmap_gen.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/netfilter/ipset/ip_set_bitmap_gen.h b/net/netfilter/ipset/ip_set_bitmap_gen.h
index 063df74b46470..e1f271a1b2c14 100644
--- a/net/netfilter/ipset/ip_set_bitmap_gen.h
+++ b/net/netfilter/ipset/ip_set_bitmap_gen.h
@@ -60,9 +60,9 @@ mtype_destroy(struct ip_set *set)
 	if (SET_WITH_TIMEOUT(set))
 		del_timer_sync(&map->gc);
 
-	ip_set_free(map->members);
 	if (set->dsize && set->extensions & IPSET_EXT_DESTROY)
 		mtype_ext_cleanup(set);
+	ip_set_free(map->members);
 	ip_set_free(map);
 
 	set->data = NULL;
-- 
2.20.1

[PATCH AUTOSEL 5.4 060/107] netfilter: arp_tables: init netns pointer in xt_tgdtor_param struct

[Sasha Levin]

From: Florian Westphal <fw@strlen.de>

[ Upstream commit 212e7f56605ef9688d0846db60c6c6ec06544095 ]

An earlier commit (1b789577f655060d98d20e,
"netfilter: arp_tables: init netns pointer in xt_tgchk_param struct")
fixed missing net initialization for arptables, but turns out it was
incomplete.  We can get a very similar struct net NULL deref during
error unwinding:

general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:xt_rateest_put+0xa1/0x440 net/netfilter/xt_RATEEST.c:77
 xt_rateest_tg_destroy+0x72/0xa0 net/netfilter/xt_RATEEST.c:175
 cleanup_entry net/ipv4/netfilter/arp_tables.c:509 [inline]
 translate_table+0x11f4/0x1d80 net/ipv4/netfilter/arp_tables.c:587
 do_replace net/ipv4/netfilter/arp_tables.c:981 [inline]
 do_arpt_set_ctl+0x317/0x650 net/ipv4/netfilter/arp_tables.c:1461

Also init the netns pointer in xt_tgdtor_param struct.

Fixes: add67461240c1d ("netfilter: add struct net * to target parameters")
Reported-by: syzbot+91bdd8eece0f6629ec8b@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/ipv4/netfilter/arp_tables.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

diff --git a/net/ipv4/netfilter/arp_tables.c b/net/ipv4/netfilter/arp_tables.c
index 069f72edb2640..f1f78a742b36a 100644
--- a/net/ipv4/netfilter/arp_tables.c
+++ b/net/ipv4/netfilter/arp_tables.c
@@ -496,12 +496,13 @@ static inline int check_entry_size_and_hooks(struct arpt_entry *e,
 	return 0;
 }
 
-static inline void cleanup_entry(struct arpt_entry *e)
+static void cleanup_entry(struct arpt_entry *e, struct net *net)
 {
 	struct xt_tgdtor_param par;
 	struct xt_entry_target *t;
 
 	t = arpt_get_target(e);
+	par.net      = net;
 	par.target   = t->u.kernel.target;
 	par.targinfo = t->data;
 	par.family   = NFPROTO_ARP;
@@ -584,7 +585,7 @@ static int translate_table(struct net *net,
 		xt_entry_foreach(iter, entry0, newinfo->size) {
 			if (i-- == 0)
 				break;
-			cleanup_entry(iter);
+			cleanup_entry(iter, net);
 		}
 		return ret;
 	}
@@ -927,7 +928,7 @@ static int __do_replace(struct net *net, const char *name,
 	/* Decrease module usage counts and free resource */
 	loc_cpu_old_entry = oldinfo->entries;
 	xt_entry_foreach(iter, loc_cpu_old_entry, oldinfo->size)
-		cleanup_entry(iter);
+		cleanup_entry(iter, net);
 
 	xt_free_table_info(oldinfo);
 	if (copy_to_user(counters_ptr, counters,
@@ -990,7 +991,7 @@ static int do_replace(struct net *net, const void __user *user,
 
  free_newinfo_untrans:
 	xt_entry_foreach(iter, loc_cpu_entry, newinfo->size)
-		cleanup_entry(iter);
+		cleanup_entry(iter, net);
  free_newinfo:
 	xt_free_table_info(newinfo);
 	return ret;
@@ -1287,7 +1288,7 @@ static int compat_do_replace(struct net *net, void __user *user,
 
  free_newinfo_untrans:
 	xt_entry_foreach(iter, loc_cpu_entry, newinfo->size)
-		cleanup_entry(iter);
+		cleanup_entry(iter, net);
  free_newinfo:
 	xt_free_table_info(newinfo);
 	return ret;
@@ -1514,7 +1515,7 @@ static int do_arpt_get_ctl(struct sock *sk, int cmd, void __user *user, int *len
 	return ret;
 }
 
-static void __arpt_unregister_table(struct xt_table *table)
+static void __arpt_unregister_table(struct net *net, struct xt_table *table)
 {
 	struct xt_table_info *private;
 	void *loc_cpu_entry;
@@ -1526,7 +1527,7 @@ static void __arpt_unregister_table(struct xt_table *table)
 	/* Decrease module usage counts and free resources */
 	loc_cpu_entry = private->entries;
 	xt_entry_foreach(iter, loc_cpu_entry, private->size)
-		cleanup_entry(iter);
+		cleanup_entry(iter, net);
 	if (private->number > private->initial_entries)
 		module_put(table_owner);
 	xt_free_table_info(private);
@@ -1566,7 +1567,7 @@ int arpt_register_table(struct net *net,
 
 	ret = nf_register_net_hooks(net, ops, hweight32(table->valid_hooks));
 	if (ret != 0) {
-		__arpt_unregister_table(new_table);
+		__arpt_unregister_table(net, new_table);
 		*res = NULL;
 	}
 
@@ -1581,7 +1582,7 @@ void arpt_unregister_table(struct net *net, struct xt_table *table,
 			   const struct nf_hook_ops *ops)
 {
 	nf_unregister_net_hooks(net, ops, hweight32(table->valid_hooks));
-	__arpt_unregister_table(table);
+	__arpt_unregister_table(net, table);
 }
 
 /* The built-in targets: standard (NULL) and error. */
-- 
2.20.1

[PATCH AUTOSEL 5.4 061/107] qmi_wwan: Add support for Quectel RM500Q

[Sasha Levin]

From: Kristian Evensen <kristian.evensen@gmail.com>

[ Upstream commit a9ff44f0e61d074f29770413fef6a5452be7b83e ]

RM500Q is a 5G module from Quectel, supporting both standalone and
non-standalone modes. The normal Quectel quirks apply (DTR and dynamic
interface numbers).

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/qmi_wwan.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/usb/qmi_wwan.c b/drivers/net/usb/qmi_wwan.c
index 4196c0e327403..9485c8d1de8a3 100644
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c
@@ -1062,6 +1062,7 @@ static const struct usb_device_id products[] = {
 	{QMI_QUIRK_QUECTEL_DYNCFG(0x2c7c, 0x0125)},	/* Quectel EC25, EC20 R2.0  Mini PCIe */
 	{QMI_QUIRK_QUECTEL_DYNCFG(0x2c7c, 0x0306)},	/* Quectel EP06/EG06/EM06 */
 	{QMI_QUIRK_QUECTEL_DYNCFG(0x2c7c, 0x0512)},	/* Quectel EG12/EM12 */
+	{QMI_QUIRK_QUECTEL_DYNCFG(0x2c7c, 0x0800)},	/* Quectel RM500Q-GL */
 
 	/* 3. Combined interface devices matching on interface number */
 	{QMI_FIXED_INTF(0x0408, 0xea42, 4)},	/* Yota / Megafon M100-1 */
-- 
2.20.1

[PATCH AUTOSEL 5.4 062/107] NFC: pn533: fix bulk-message timeout

[Sasha Levin]

From: Johan Hovold <johan@kernel.org>

[ Upstream commit a112adafcb47760feff959ee1ecd10b74d2c5467 ]

The driver was doing a synchronous uninterruptible bulk-transfer without
using a timeout. This could lead to the driver hanging on probe due to a
malfunctioning (or malicious) device until the device is physically
disconnected. While sleeping in probe the driver prevents other devices
connected to the same hub from being added to (or removed from) the bus.

An arbitrary limit of five seconds should be more than enough.

Fixes: dbafc28955fa ("NFC: pn533: don't send USB data off of the stack")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/nfc/pn533/usb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/nfc/pn533/usb.c b/drivers/nfc/pn533/usb.c
index e897e4d768ef7..d7a355d053687 100644
--- a/drivers/nfc/pn533/usb.c
+++ b/drivers/nfc/pn533/usb.c
@@ -391,7 +391,7 @@ static int pn533_acr122_poweron_rdr(struct pn533_usb_phy *phy)
 		       cmd, sizeof(cmd), false);
 
 	rc = usb_bulk_msg(phy->udev, phy->out_urb->pipe, buffer, sizeof(cmd),
-			  &transferred, 0);
+			  &transferred, 5000);
 	kfree(buffer);
 	if (rc || (transferred != sizeof(cmd))) {
 		nfc_err(&phy->udev->dev,
-- 
2.20.1

[PATCH AUTOSEL 5.4 063/107] parisc: Use proper printk format for resource_size_t

[Sasha Levin]

From: Krzysztof Kozlowski <krzk@kernel.org>

[ Upstream commit 4f80b70e1953cb846dbdd1ce72cb17333d4c8d11 ]

resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):

    arch/parisc/kernel/drivers.c: In function 'print_parisc_device':
    arch/parisc/kernel/drivers.c:892:9: warning:
        format '%p' expects argument of type 'void *',
        but argument 4 has type 'resource_size_t {aka unsigned int}' [-Wformat=]

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/parisc/kernel/drivers.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/parisc/kernel/drivers.c b/arch/parisc/kernel/drivers.c
index a6c9f49c66128..a5f3e50fe9761 100644
--- a/arch/parisc/kernel/drivers.c
+++ b/arch/parisc/kernel/drivers.c
@@ -889,8 +889,8 @@ static void print_parisc_device(struct parisc_device *dev)
 	static int count;
 
 	print_pa_hwpath(dev, hw_path);
-	pr_info("%d. %s at 0x%px [%s] { %d, 0x%x, 0x%.3x, 0x%.5x }",
-		++count, dev->name, (void*) dev->hpa.start, hw_path, dev->id.hw_type,
+	pr_info("%d. %s at %pap [%s] { %d, 0x%x, 0x%.3x, 0x%.5x }",
+		++count, dev->name, &(dev->hpa.start), hw_path, dev->id.hw_type,
 		dev->id.hversion_rev, dev->id.hversion, dev->id.sversion);
 
 	if (dev->num_addrs) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 064/107] lkdtm/bugs: fix build error in lkdtm_UNSET_SMEP

[Sasha Levin]

From: Brendan Higgins <brendanhiggins@google.com>

[ Upstream commit 0e31e3573f0cd94d7b821117db854187ffc85765 ]

When building ARCH=um with CONFIG_UML_X86=y and CONFIG_64BIT=y we get
the build errors:

drivers/misc/lkdtm/bugs.c: In function ‘lkdtm_UNSET_SMEP’:
drivers/misc/lkdtm/bugs.c:288:8: error: implicit declaration of function ‘native_read_cr4’ [-Werror=implicit-function-declaration]
  cr4 = native_read_cr4();
        ^~~~~~~~~~~~~~~
drivers/misc/lkdtm/bugs.c:290:13: error: ‘X86_CR4_SMEP’ undeclared (first use in this function); did you mean ‘X86_FEATURE_SMEP’?
  if ((cr4 & X86_CR4_SMEP) != X86_CR4_SMEP) {
             ^~~~~~~~~~~~
             X86_FEATURE_SMEP
drivers/misc/lkdtm/bugs.c:290:13: note: each undeclared identifier is reported only once for each function it appears in
drivers/misc/lkdtm/bugs.c:297:2: error: implicit declaration of function ‘native_write_cr4’; did you mean ‘direct_write_cr4’? [-Werror=implicit-function-declaration]
  native_write_cr4(cr4);
  ^~~~~~~~~~~~~~~~
  direct_write_cr4

So specify that this block of code should only build when
CONFIG_X86_64=y *AND* CONFIG_UML is unset.

Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20191213003522.66450-1-brendanhiggins@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/misc/lkdtm/bugs.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/misc/lkdtm/bugs.c b/drivers/misc/lkdtm/bugs.c
index 7284a22b1a09e..4d5a512769e99 100644
--- a/drivers/misc/lkdtm/bugs.c
+++ b/drivers/misc/lkdtm/bugs.c
@@ -274,7 +274,7 @@ void lkdtm_STACK_GUARD_PAGE_TRAILING(void)
 
 void lkdtm_UNSET_SMEP(void)
 {
-#ifdef CONFIG_X86_64
+#if IS_ENABLED(CONFIG_X86_64) && !IS_ENABLED(CONFIG_UML)
 #define MOV_CR4_DEPTH	64
 	void (*direct_write_cr4)(unsigned long val);
 	unsigned char *insn;
-- 
2.20.1

[PATCH AUTOSEL 5.4 065/107] ptp: free ptp device pin descriptors properly

[Sasha Levin]

From: Vladis Dronov <vdronov@redhat.com>

[ Upstream commit 75718584cb3c64e6269109d4d54f888ac5a5fd15 ]

There is a bug in ptp_clock_unregister(), where ptp_cleanup_pin_groups()
first frees ptp->pin_{,dev_}attr, but then posix_clock_unregister() needs
them to destroy a related sysfs device.

These functions can not be just swapped, as posix_clock_unregister() frees
ptp which is needed in the ptp_cleanup_pin_groups(). Fix this by calling
ptp_cleanup_pin_groups() in ptp_clock_release(), right before ptp is freed.

This makes this patch fix an UAF bug in a patch which fixes an UAF bug.

Reported-by: Antti Laakso <antti.laakso@intel.com>
Fixes: a33121e5487b ("ptp: fix the race between the release of ptp_clock and cdev")
Link: https://lore.kernel.org/netdev/3d2bd09735dbdaf003585ca376b7c1e5b69a19bd.camel@intel.com/
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/ptp/ptp_clock.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/ptp/ptp_clock.c b/drivers/ptp/ptp_clock.c
index 61fafe0374cea..b84f16bbd6f24 100644
--- a/drivers/ptp/ptp_clock.c
+++ b/drivers/ptp/ptp_clock.c
@@ -170,6 +170,7 @@ static void ptp_clock_release(struct device *dev)
 {
 	struct ptp_clock *ptp = container_of(dev, struct ptp_clock, dev);
 
+	ptp_cleanup_pin_groups(ptp);
 	mutex_destroy(&ptp->tsevq_mux);
 	mutex_destroy(&ptp->pincfg_mux);
 	ida_simple_remove(&ptp_clocks_map, ptp->index);
@@ -302,9 +303,8 @@ int ptp_clock_unregister(struct ptp_clock *ptp)
 	if (ptp->pps_source)
 		pps_unregister_source(ptp->pps_source);
 
-	ptp_cleanup_pin_groups(ptp);
-
 	posix_clock_unregister(&ptp->clock);
+
 	return 0;
 }
 EXPORT_SYMBOL(ptp_clock_unregister);
-- 
2.20.1

[PATCH AUTOSEL 5.4 066/107] net: usb: lan78xx: limit size of local TSO packets

[Sasha Levin]

From: Eric Dumazet <edumazet@google.com>

[ Upstream commit f8d7408a4d7f60f8b2df0f81decdc882dd9c20dc ]

lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.

Pierre-Francois reported various hangs when/if TSO is enabled.

For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.

Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.

Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Tested-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/lan78xx.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c
index 3e5f2f7a155e1..c232f16120830 100644
--- a/drivers/net/usb/lan78xx.c
+++ b/drivers/net/usb/lan78xx.c
@@ -3750,6 +3750,7 @@ static int lan78xx_probe(struct usb_interface *intf,
 
 	/* MTU range: 68 - 9000 */
 	netdev->max_mtu = MAX_SINGLE_PACKET_SIZE;
+	netif_set_gso_max_size(netdev, MAX_SINGLE_PACKET_SIZE - MAX_HEADER);
 
 	dev->ep_blkin = (intf->cur_altsetting)->endpoint + 0;
 	dev->ep_blkout = (intf->cur_altsetting)->endpoint + 1;
-- 
2.20.1

[PATCH AUTOSEL 5.4 067/107] r8152: add missing endpoint sanity check

[Sasha Levin]

From: Johan Hovold <johan@kernel.org>

[ Upstream commit 86f3f4cd53707ceeec079b83205c8d3c756eca93 ]

Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.

Fixes: 40a82917b1d3 ("net/usb/r8152: enable interrupt transfer")
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/r8152.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c
index b2507c59ba8b3..9e4b7a4002843 100644
--- a/drivers/net/usb/r8152.c
+++ b/drivers/net/usb/r8152.c
@@ -5587,6 +5587,9 @@ static int rtl8152_probe(struct usb_interface *intf,
 		return -ENODEV;
 	}
 
+	if (intf->cur_altsetting->desc.bNumEndpoints < 3)
+		return -ENODEV;
+
 	usb_reset_device(udev);
 	netdev = alloc_etherdev(sizeof(struct r8152));
 	if (!netdev) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 068/107] wireless: fix enabling channel 12 for custom regulatory domain

[Sasha Levin]

From: Ganapathi Bhat <ganapathi.bhat@nxp.com>

[ Upstream commit c4b9d655e445a8be0bff624aedea190606b5ebbc ]

Commit e33e2241e272 ("Revert "cfg80211: Use 5MHz bandwidth by
default when checking usable channels"") fixed a broken
regulatory (leaving channel 12 open for AP where not permitted).
Apply a similar fix to custom regulatory domain processing.

Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Link: https://lore.kernel.org/r/1576836859-8945-1-git-send-email-ganapathi.bhat@nxp.com
[reword commit message, fix coding style, add a comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/wireless/reg.c | 13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)

diff --git a/net/wireless/reg.c b/net/wireless/reg.c
index 446c76d44e65a..3c2070040277d 100644
--- a/net/wireless/reg.c
+++ b/net/wireless/reg.c
@@ -2261,14 +2261,15 @@ static void update_all_wiphy_regulatory(enum nl80211_reg_initiator initiator)
 
 static void handle_channel_custom(struct wiphy *wiphy,
 				  struct ieee80211_channel *chan,
-				  const struct ieee80211_regdomain *regd)
+				  const struct ieee80211_regdomain *regd,
+				  u32 min_bw)
 {
 	u32 bw_flags = 0;
 	const struct ieee80211_reg_rule *reg_rule = NULL;
 	const struct ieee80211_power_rule *power_rule = NULL;
 	u32 bw;
 
-	for (bw = MHZ_TO_KHZ(20); bw >= MHZ_TO_KHZ(5); bw = bw / 2) {
+	for (bw = MHZ_TO_KHZ(20); bw >= min_bw; bw = bw / 2) {
 		reg_rule = freq_reg_info_regd(MHZ_TO_KHZ(chan->center_freq),
 					      regd, bw);
 		if (!IS_ERR(reg_rule))
@@ -2324,8 +2325,14 @@ static void handle_band_custom(struct wiphy *wiphy,
 	if (!sband)
 		return;
 
+	/*
+	 * We currently assume that you always want at least 20 MHz,
+	 * otherwise channel 12 might get enabled if this rule is
+	 * compatible to US, which permits 2402 - 2472 MHz.
+	 */
 	for (i = 0; i < sband->n_channels; i++)
-		handle_channel_custom(wiphy, &sband->channels[i], regd);
+		handle_channel_custom(wiphy, &sband->channels[i], regd,
+				      MHZ_TO_KHZ(20));
 }
 
 /* Used by drivers prior to wiphy registration */
-- 
2.20.1

[PATCH AUTOSEL 5.4 069/107] cfg80211: Fix radar event during another phy CAC

[Sasha Levin]

From: Orr Mazor <orr.mazor@tandemg.com>

[ Upstream commit 26ec17a1dc5ecdd8d91aba63ead6f8b5ad5dea0d ]

In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.

If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.

If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.

To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant

Signed-off-by: Orr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/net/cfg80211.h  |  5 +++++
 net/mac80211/cfg.c      | 23 +++++++++++++++++++++++
 net/wireless/rdev-ops.h | 10 ++++++++++
 net/wireless/reg.c      | 23 ++++++++++++++++++++++-
 net/wireless/trace.h    |  5 +++++
 5 files changed, 65 insertions(+), 1 deletion(-)

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 4ab2c49423dcb..68782ba8b6e8d 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -3537,6 +3537,9 @@ struct cfg80211_update_owe_info {
  *
  * @start_radar_detection: Start radar detection in the driver.
  *
+ * @end_cac: End running CAC, probably because a related CAC
+ *	was finished on another phy.
+ *
  * @update_ft_ies: Provide updated Fast BSS Transition information to the
  *	driver. If the SME is in the driver/firmware, this information can be
  *	used in building Authentication and Reassociation Request frames.
@@ -3863,6 +3866,8 @@ struct cfg80211_ops {
 					 struct net_device *dev,
 					 struct cfg80211_chan_def *chandef,
 					 u32 cac_time_ms);
+	void	(*end_cac)(struct wiphy *wiphy,
+				struct net_device *dev);
 	int	(*update_ft_ies)(struct wiphy *wiphy, struct net_device *dev,
 				 struct cfg80211_update_ft_ies_params *ftie);
 	int	(*crit_proto_start)(struct wiphy *wiphy,
diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c
index 70739e746c13e..0daaf7e37a211 100644
--- a/net/mac80211/cfg.c
+++ b/net/mac80211/cfg.c
@@ -2954,6 +2954,28 @@ static int ieee80211_start_radar_detection(struct wiphy *wiphy,
 	return err;
 }
 
+static void ieee80211_end_cac(struct wiphy *wiphy,
+			      struct net_device *dev)
+{
+	struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+	struct ieee80211_local *local = sdata->local;
+
+	mutex_lock(&local->mtx);
+	list_for_each_entry(sdata, &local->interfaces, list) {
+		/* it might be waiting for the local->mtx, but then
+		 * by the time it gets it, sdata->wdev.cac_started
+		 * will no longer be true
+		 */
+		cancel_delayed_work(&sdata->dfs_cac_timer_work);
+
+		if (sdata->wdev.cac_started) {
+			ieee80211_vif_release_channel(sdata);
+			sdata->wdev.cac_started = false;
+		}
+	}
+	mutex_unlock(&local->mtx);
+}
+
 static struct cfg80211_beacon_data *
 cfg80211_beacon_dup(struct cfg80211_beacon_data *beacon)
 {
@@ -4023,6 +4045,7 @@ const struct cfg80211_ops mac80211_config_ops = {
 #endif
 	.get_channel = ieee80211_cfg_get_channel,
 	.start_radar_detection = ieee80211_start_radar_detection,
+	.end_cac = ieee80211_end_cac,
 	.channel_switch = ieee80211_channel_switch,
 	.set_qos_map = ieee80211_set_qos_map,
 	.set_ap_chanwidth = ieee80211_set_ap_chanwidth,
diff --git a/net/wireless/rdev-ops.h b/net/wireless/rdev-ops.h
index e853a4fe6f97f..663c0d3127a43 100644
--- a/net/wireless/rdev-ops.h
+++ b/net/wireless/rdev-ops.h
@@ -1167,6 +1167,16 @@ rdev_start_radar_detection(struct cfg80211_registered_device *rdev,
 	return ret;
 }
 
+static inline void
+rdev_end_cac(struct cfg80211_registered_device *rdev,
+	     struct net_device *dev)
+{
+	trace_rdev_end_cac(&rdev->wiphy, dev);
+	if (rdev->ops->end_cac)
+		rdev->ops->end_cac(&rdev->wiphy, dev);
+	trace_rdev_return_void(&rdev->wiphy);
+}
+
 static inline int
 rdev_set_mcast_rate(struct cfg80211_registered_device *rdev,
 		    struct net_device *dev,
diff --git a/net/wireless/reg.c b/net/wireless/reg.c
index 3c2070040277d..fff9a74891fc4 100644
--- a/net/wireless/reg.c
+++ b/net/wireless/reg.c
@@ -3892,6 +3892,25 @@ bool regulatory_pre_cac_allowed(struct wiphy *wiphy)
 }
 EXPORT_SYMBOL(regulatory_pre_cac_allowed);
 
+static void cfg80211_check_and_end_cac(struct cfg80211_registered_device *rdev)
+{
+	struct wireless_dev *wdev;
+	/* If we finished CAC or received radar, we should end any
+	 * CAC running on the same channels.
+	 * the check !cfg80211_chandef_dfs_usable contain 2 options:
+	 * either all channels are available - those the CAC_FINISHED
+	 * event has effected another wdev state, or there is a channel
+	 * in unavailable state in wdev chandef - those the RADAR_DETECTED
+	 * event has effected another wdev state.
+	 * In both cases we should end the CAC on the wdev.
+	 */
+	list_for_each_entry(wdev, &rdev->wiphy.wdev_list, list) {
+		if (wdev->cac_started &&
+		    !cfg80211_chandef_dfs_usable(&rdev->wiphy, &wdev->chandef))
+			rdev_end_cac(rdev, wdev->netdev);
+	}
+}
+
 void regulatory_propagate_dfs_state(struct wiphy *wiphy,
 				    struct cfg80211_chan_def *chandef,
 				    enum nl80211_dfs_state dfs_state,
@@ -3918,8 +3937,10 @@ void regulatory_propagate_dfs_state(struct wiphy *wiphy,
 		cfg80211_set_dfs_state(&rdev->wiphy, chandef, dfs_state);
 
 		if (event == NL80211_RADAR_DETECTED ||
-		    event == NL80211_RADAR_CAC_FINISHED)
+		    event == NL80211_RADAR_CAC_FINISHED) {
 			cfg80211_sched_dfs_chan_update(rdev);
+			cfg80211_check_and_end_cac(rdev);
+		}
 
 		nl80211_radar_notify(rdev, chandef, event, NULL, GFP_KERNEL);
 	}
diff --git a/net/wireless/trace.h b/net/wireless/trace.h
index d98ad2b3143b0..8677d7ab7d692 100644
--- a/net/wireless/trace.h
+++ b/net/wireless/trace.h
@@ -646,6 +646,11 @@ DEFINE_EVENT(wiphy_netdev_evt, rdev_flush_pmksa,
 	TP_ARGS(wiphy, netdev)
 );
 
+DEFINE_EVENT(wiphy_netdev_evt, rdev_end_cac,
+	     TP_PROTO(struct wiphy *wiphy, struct net_device *netdev),
+	     TP_ARGS(wiphy, netdev)
+);
+
 DECLARE_EVENT_CLASS(station_add_change,
 	TP_PROTO(struct wiphy *wiphy, struct net_device *netdev, u8 *mac,
 		 struct station_parameters *params),
-- 
2.20.1

[PATCH AUTOSEL 5.4 070/107] mac80211: Fix TKIP replay protection immediately after key setup

[Sasha Levin]

From: Jouni Malinen <j@w1.fi>

[ Upstream commit 6f601265215a421f425ba3a4850a35861d024643 ]

TKIP replay protection was skipped for the very first frame received
after a new key is configured. While this is potentially needed to avoid
dropping a frame in some cases, this does leave a window for replay
attacks with group-addressed frames at the station side. Any earlier
frame sent by the AP using the same key would be accepted as a valid
frame and the internal RSC would then be updated to the TSC from that
frame. This would allow multiple previously transmitted group-addressed
frames to be replayed until the next valid new group-addressed frame
from the AP is received by the station.

Fix this by limiting the no-replay-protection exception to apply only
for the case where TSC=0, i.e., when this is for the very first frame
protected using the new key, and the local RSC had not been set to a
higher value when configuring the key (which may happen with GTK).

Signed-off-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20200107153545.10934-1-j@w1.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/mac80211/tkip.c | 18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)

diff --git a/net/mac80211/tkip.c b/net/mac80211/tkip.c
index 727dc9f3f3b3a..e7f57bb18f6e0 100644
--- a/net/mac80211/tkip.c
+++ b/net/mac80211/tkip.c
@@ -263,9 +263,21 @@ int ieee80211_tkip_decrypt_data(struct arc4_ctx *ctx,
 	if ((keyid >> 6) != key->conf.keyidx)
 		return TKIP_DECRYPT_INVALID_KEYIDX;
 
-	if (rx_ctx->ctx.state != TKIP_STATE_NOT_INIT &&
-	    (iv32 < rx_ctx->iv32 ||
-	     (iv32 == rx_ctx->iv32 && iv16 <= rx_ctx->iv16)))
+	/* Reject replays if the received TSC is smaller than or equal to the
+	 * last received value in a valid message, but with an exception for
+	 * the case where a new key has been set and no valid frame using that
+	 * key has yet received and the local RSC was initialized to 0. This
+	 * exception allows the very first frame sent by the transmitter to be
+	 * accepted even if that transmitter were to use TSC 0 (IEEE 802.11
+	 * described TSC to be initialized to 1 whenever a new key is taken into
+	 * use).
+	 */
+	if (iv32 < rx_ctx->iv32 ||
+	    (iv32 == rx_ctx->iv32 &&
+	     (iv16 < rx_ctx->iv16 ||
+	      (iv16 == rx_ctx->iv16 &&
+	       (rx_ctx->iv32 || rx_ctx->iv16 ||
+		rx_ctx->ctx.state != TKIP_STATE_NOT_INIT)))))
 		return TKIP_DECRYPT_REPLAY;
 
 	if (only_iv) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 071/107] wireless: wext: avoid gcc -O3 warning

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit e16119655c9e6c4aa5767cd971baa9c491f41b13 ]

After the introduction of CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3,
the wext code produces a bogus warning:

In function 'iw_handler_get_iwstats',
    inlined from 'ioctl_standard_call' at net/wireless/wext-core.c:1015:9,
    inlined from 'wireless_process_ioctl' at net/wireless/wext-core.c:935:10,
    inlined from 'wext_ioctl_dispatch.part.8' at net/wireless/wext-core.c:986:8,
    inlined from 'wext_handle_ioctl':
net/wireless/wext-core.c:671:3: error: argument 1 null where non-null expected [-Werror=nonnull]
   memcpy(extra, stats, sizeof(struct iw_statistics));
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from arch/x86/include/asm/string.h:5,
net/wireless/wext-core.c: In function 'wext_handle_ioctl':
arch/x86/include/asm/string_64.h:14:14: note: in a call to function 'memcpy' declared here

The problem is that ioctl_standard_call() sometimes calls the handler
with a NULL argument that would cause a problem for iw_handler_get_iwstats.
However, iw_handler_get_iwstats never actually gets called that way.

Marking that function as noinline avoids the warning and leads
to slightly smaller object code as well.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200107200741.3588770-1-arnd@arndb.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/wireless/wext-core.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/net/wireless/wext-core.c b/net/wireless/wext-core.c
index 5e677dac2a0ce..69102fda9ebd4 100644
--- a/net/wireless/wext-core.c
+++ b/net/wireless/wext-core.c
@@ -657,7 +657,8 @@ struct iw_statistics *get_wireless_stats(struct net_device *dev)
 	return NULL;
 }
 
-static int iw_handler_get_iwstats(struct net_device *		dev,
+/* noinline to avoid a bogus warning with -O3 */
+static noinline int iw_handler_get_iwstats(struct net_device *	dev,
 				  struct iw_request_info *	info,
 				  union iwreq_data *		wrqu,
 				  char *			extra)
-- 
2.20.1

[PATCH AUTOSEL 5.4 072/107] cfg80211: check for set_wiphy_params

[Sasha Levin]

From: Johannes Berg <johannes.berg@intel.com>

[ Upstream commit 24953de0a5e31dcca7e82c8a3c79abc2dfe8fb6e ]

Check if set_wiphy_params is assigned and return an error if not,
some drivers (e.g. virt_wifi where syzbot reported it) don't have
it.

Reported-by: syzbot+e8a797964a4180eb57d5@syzkaller.appspotmail.com
Reported-by: syzbot+34b582cf32c1db008f8e@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200113125358.ac07f276efff.Ibd85ee1b12e47b9efb00a2adc5cd3fac50da791a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/wireless/rdev-ops.h | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/net/wireless/rdev-ops.h b/net/wireless/rdev-ops.h
index 663c0d3127a43..e0d34f796d0b3 100644
--- a/net/wireless/rdev-ops.h
+++ b/net/wireless/rdev-ops.h
@@ -538,6 +538,10 @@ static inline int
 rdev_set_wiphy_params(struct cfg80211_registered_device *rdev, u32 changed)
 {
 	int ret;
+
+	if (!rdev->ops->set_wiphy_params)
+		return -EOPNOTSUPP;
+
 	trace_rdev_set_wiphy_params(&rdev->wiphy, changed);
 	ret = rdev->ops->set_wiphy_params(&rdev->wiphy, changed);
 	trace_rdev_return_int(&rdev->wiphy, ret);
-- 
2.20.1

[PATCH AUTOSEL 5.4 073/107] tick/sched: Annotate lockless access to last_jiffies_update

[Sasha Levin]

From: Eric Dumazet <edumazet@google.com>

[ Upstream commit de95a991bb72e009f47e0c4bbc90fc5f594588d5 ]

syzbot (KCSAN) reported a data-race in tick_do_update_jiffies64():

BUG: KCSAN: data-race in tick_do_update_jiffies64 / tick_do_update_jiffies64

write to 0xffffffff8603d008 of 8 bytes by interrupt on cpu 1:
 tick_do_update_jiffies64+0x100/0x250 kernel/time/tick-sched.c:73
 tick_sched_do_timer+0xd4/0xe0 kernel/time/tick-sched.c:138
 tick_sched_timer+0x43/0xe0 kernel/time/tick-sched.c:1292
 __run_hrtimer kernel/time/hrtimer.c:1514 [inline]
 __hrtimer_run_queues+0x274/0x5f0 kernel/time/hrtimer.c:1576
 hrtimer_interrupt+0x22a/0x480 kernel/time/hrtimer.c:1638
 local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1110 [inline]
 smp_apic_timer_interrupt+0xdc/0x280 arch/x86/kernel/apic/apic.c:1135
 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:830
 arch_local_irq_restore arch/x86/include/asm/paravirt.h:756 [inline]
 kcsan_setup_watchpoint+0x1d4/0x460 kernel/kcsan/core.c:436
 check_access kernel/kcsan/core.c:466 [inline]
 __tsan_read1 kernel/kcsan/core.c:593 [inline]
 __tsan_read1+0xc2/0x100 kernel/kcsan/core.c:593
 kallsyms_expand_symbol.constprop.0+0x70/0x160 kernel/kallsyms.c:79
 kallsyms_lookup_name+0x7f/0x120 kernel/kallsyms.c:170
 insert_report_filterlist kernel/kcsan/debugfs.c:155 [inline]
 debugfs_write+0x14b/0x2d0 kernel/kcsan/debugfs.c:256
 full_proxy_write+0xbd/0x100 fs/debugfs/file.c:225
 __vfs_write+0x67/0xc0 fs/read_write.c:494
 vfs_write fs/read_write.c:558 [inline]
 vfs_write+0x18a/0x390 fs/read_write.c:542
 ksys_write+0xd5/0x1b0 fs/read_write.c:611
 __do_sys_write fs/read_write.c:623 [inline]
 __se_sys_write fs/read_write.c:620 [inline]
 __x64_sys_write+0x4c/0x60 fs/read_write.c:620
 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

read to 0xffffffff8603d008 of 8 bytes by task 0 on cpu 0:
 tick_do_update_jiffies64+0x2b/0x250 kernel/time/tick-sched.c:62
 tick_nohz_update_jiffies kernel/time/tick-sched.c:505 [inline]
 tick_nohz_irq_enter kernel/time/tick-sched.c:1257 [inline]
 tick_irq_enter+0x139/0x1c0 kernel/time/tick-sched.c:1274
 irq_enter+0x4f/0x60 kernel/softirq.c:354
 entering_irq arch/x86/include/asm/apic.h:517 [inline]
 entering_ack_irq arch/x86/include/asm/apic.h:523 [inline]
 smp_apic_timer_interrupt+0x55/0x280 arch/x86/kernel/apic/apic.c:1133
 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:830
 native_safe_halt+0xe/0x10 arch/x86/include/asm/irqflags.h:60
 arch_cpu_idle+0xa/0x10 arch/x86/kernel/process.c:571
 default_idle_call+0x1e/0x40 kernel/sched/idle.c:94
 cpuidle_idle_call kernel/sched/idle.c:154 [inline]
 do_idle+0x1af/0x280 kernel/sched/idle.c:263
 cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:355
 rest_init+0xec/0xf6 init/main.c:452
 arch_call_rest_init+0x17/0x37
 start_kernel+0x838/0x85e init/main.c:786
 x86_64_start_reservations+0x29/0x2b arch/x86/kernel/head64.c:490
 x86_64_start_kernel+0x72/0x76 arch/x86/kernel/head64.c:471
 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:241

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Use READ_ONCE() and WRITE_ONCE() to annotate this expected race.

Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191205045619.204946-1-edumazet@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/time/tick-sched.c | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)

diff --git a/kernel/time/tick-sched.c b/kernel/time/tick-sched.c
index 955851748dc38..5c9fcc72460df 100644
--- a/kernel/time/tick-sched.c
+++ b/kernel/time/tick-sched.c
@@ -58,8 +58,9 @@ static void tick_do_update_jiffies64(ktime_t now)
 
 	/*
 	 * Do a quick check without holding jiffies_lock:
+	 * The READ_ONCE() pairs with two updates done later in this function.
 	 */
-	delta = ktime_sub(now, last_jiffies_update);
+	delta = ktime_sub(now, READ_ONCE(last_jiffies_update));
 	if (delta < tick_period)
 		return;
 
@@ -70,8 +71,9 @@ static void tick_do_update_jiffies64(ktime_t now)
 	if (delta >= tick_period) {
 
 		delta = ktime_sub(delta, tick_period);
-		last_jiffies_update = ktime_add(last_jiffies_update,
-						tick_period);
+		/* Pairs with the lockless read in this function. */
+		WRITE_ONCE(last_jiffies_update,
+			   ktime_add(last_jiffies_update, tick_period));
 
 		/* Slow path for long timeouts */
 		if (unlikely(delta >= tick_period)) {
@@ -79,8 +81,10 @@ static void tick_do_update_jiffies64(ktime_t now)
 
 			ticks = ktime_divns(delta, incr);
 
-			last_jiffies_update = ktime_add_ns(last_jiffies_update,
-							   incr * ticks);
+			/* Pairs with the lockless read in this function. */
+			WRITE_ONCE(last_jiffies_update,
+				   ktime_add_ns(last_jiffies_update,
+						incr * ticks));
 		}
 		do_timer(++ticks);
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 074/107] Revert "gpio: thunderx: Switch to GPIOLIB_IRQCHIP"

[Sasha Levin]

From: Kevin Hao <haokexin@gmail.com>

[ Upstream commit a564ac35d60564dd5b509e32afdc04e7aafee40e ]

This reverts commit a7fc89f9d5fcc10a5474cfe555f5a9e5df8b0f1f because
there are some bugs in this commit, and we don't have a simple way to
fix these bugs. So revert this commit to make the thunderx gpio work
on the stable kernel at least. We will switch to GPIOLIB_IRQCHIP
for thunderx gpio by following patches.

Fixes: a7fc89f9d5fc ("gpio: thunderx: Switch to GPIOLIB_IRQCHIP")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-2-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpio/Kconfig         |   1 -
 drivers/gpio/gpio-thunderx.c | 163 +++++++++++++++++++++++------------
 2 files changed, 107 insertions(+), 57 deletions(-)

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 38e096e6925fa..ceb908f7dbe51 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -546,7 +546,6 @@ config GPIO_THUNDERX
 	tristate "Cavium ThunderX/OCTEON-TX GPIO"
 	depends on ARCH_THUNDER || (64BIT && COMPILE_TEST)
 	depends on PCI_MSI
-	select GPIOLIB_IRQCHIP
 	select IRQ_DOMAIN_HIERARCHY
 	select IRQ_FASTEOI_HIERARCHY_HANDLERS
 	help
diff --git a/drivers/gpio/gpio-thunderx.c b/drivers/gpio/gpio-thunderx.c
index ddad5c7ea6176..715371b5102a5 100644
--- a/drivers/gpio/gpio-thunderx.c
+++ b/drivers/gpio/gpio-thunderx.c
@@ -53,6 +53,7 @@ struct thunderx_line {
 struct thunderx_gpio {
 	struct gpio_chip	chip;
 	u8 __iomem		*register_base;
+	struct irq_domain	*irqd;
 	struct msix_entry	*msix_entries;	/* per line MSI-X */
 	struct thunderx_line	*line_entries;	/* per line irq info */
 	raw_spinlock_t		lock;
@@ -282,60 +283,54 @@ static void thunderx_gpio_set_multiple(struct gpio_chip *chip,
 	}
 }
 
-static void thunderx_gpio_irq_ack(struct irq_data *d)
+static void thunderx_gpio_irq_ack(struct irq_data *data)
 {
-	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
-	struct thunderx_gpio *txgpio = gpiochip_get_data(gc);
+	struct thunderx_line *txline = irq_data_get_irq_chip_data(data);
 
 	writeq(GPIO_INTR_INTR,
-	       txgpio->register_base + intr_reg(irqd_to_hwirq(d)));
+	       txline->txgpio->register_base + intr_reg(txline->line));
 }
 
-static void thunderx_gpio_irq_mask(struct irq_data *d)
+static void thunderx_gpio_irq_mask(struct irq_data *data)
 {
-	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
-	struct thunderx_gpio *txgpio = gpiochip_get_data(gc);
+	struct thunderx_line *txline = irq_data_get_irq_chip_data(data);
 
 	writeq(GPIO_INTR_ENA_W1C,
-	       txgpio->register_base + intr_reg(irqd_to_hwirq(d)));
+	       txline->txgpio->register_base + intr_reg(txline->line));
 }
 
-static void thunderx_gpio_irq_mask_ack(struct irq_data *d)
+static void thunderx_gpio_irq_mask_ack(struct irq_data *data)
 {
-	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
-	struct thunderx_gpio *txgpio = gpiochip_get_data(gc);
+	struct thunderx_line *txline = irq_data_get_irq_chip_data(data);
 
 	writeq(GPIO_INTR_ENA_W1C | GPIO_INTR_INTR,
-	       txgpio->register_base + intr_reg(irqd_to_hwirq(d)));
+	       txline->txgpio->register_base + intr_reg(txline->line));
 }
 
-static void thunderx_gpio_irq_unmask(struct irq_data *d)
+static void thunderx_gpio_irq_unmask(struct irq_data *data)
 {
-	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
-	struct thunderx_gpio *txgpio = gpiochip_get_data(gc);
+	struct thunderx_line *txline = irq_data_get_irq_chip_data(data);
 
 	writeq(GPIO_INTR_ENA_W1S,
-	       txgpio->register_base + intr_reg(irqd_to_hwirq(d)));
+	       txline->txgpio->register_base + intr_reg(txline->line));
 }
 
-static int thunderx_gpio_irq_set_type(struct irq_data *d,
+static int thunderx_gpio_irq_set_type(struct irq_data *data,
 				      unsigned int flow_type)
 {
-	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
-	struct thunderx_gpio *txgpio = gpiochip_get_data(gc);
-	struct thunderx_line *txline =
-		&txgpio->line_entries[irqd_to_hwirq(d)];
+	struct thunderx_line *txline = irq_data_get_irq_chip_data(data);
+	struct thunderx_gpio *txgpio = txline->txgpio;
 	u64 bit_cfg;
 
-	irqd_set_trigger_type(d, flow_type);
+	irqd_set_trigger_type(data, flow_type);
 
 	bit_cfg = txline->fil_bits | GPIO_BIT_CFG_INT_EN;
 
 	if (flow_type & IRQ_TYPE_EDGE_BOTH) {
-		irq_set_handler_locked(d, handle_fasteoi_ack_irq);
+		irq_set_handler_locked(data, handle_fasteoi_ack_irq);
 		bit_cfg |= GPIO_BIT_CFG_INT_TYPE;
 	} else {
-		irq_set_handler_locked(d, handle_fasteoi_mask_irq);
+		irq_set_handler_locked(data, handle_fasteoi_mask_irq);
 	}
 
 	raw_spin_lock(&txgpio->lock);
@@ -364,6 +359,33 @@ static void thunderx_gpio_irq_disable(struct irq_data *data)
 	irq_chip_disable_parent(data);
 }
 
+static int thunderx_gpio_irq_request_resources(struct irq_data *data)
+{
+	struct thunderx_line *txline = irq_data_get_irq_chip_data(data);
+	struct thunderx_gpio *txgpio = txline->txgpio;
+	int r;
+
+	r = gpiochip_lock_as_irq(&txgpio->chip, txline->line);
+	if (r)
+		return r;
+
+	r = irq_chip_request_resources_parent(data);
+	if (r)
+		gpiochip_unlock_as_irq(&txgpio->chip, txline->line);
+
+	return r;
+}
+
+static void thunderx_gpio_irq_release_resources(struct irq_data *data)
+{
+	struct thunderx_line *txline = irq_data_get_irq_chip_data(data);
+	struct thunderx_gpio *txgpio = txline->txgpio;
+
+	irq_chip_release_resources_parent(data);
+
+	gpiochip_unlock_as_irq(&txgpio->chip, txline->line);
+}
+
 /*
  * Interrupts are chained from underlying MSI-X vectors.  We have
  * these irq_chip functions to be able to handle level triggering
@@ -380,24 +402,50 @@ static struct irq_chip thunderx_gpio_irq_chip = {
 	.irq_unmask		= thunderx_gpio_irq_unmask,
 	.irq_eoi		= irq_chip_eoi_parent,
 	.irq_set_affinity	= irq_chip_set_affinity_parent,
+	.irq_request_resources	= thunderx_gpio_irq_request_resources,
+	.irq_release_resources	= thunderx_gpio_irq_release_resources,
 	.irq_set_type		= thunderx_gpio_irq_set_type,
 
 	.flags			= IRQCHIP_SET_TYPE_MASKED
 };
 
-static int thunderx_gpio_child_to_parent_hwirq(struct gpio_chip *gc,
-					       unsigned int child,
-					       unsigned int child_type,
-					       unsigned int *parent,
-					       unsigned int *parent_type)
+static int thunderx_gpio_irq_translate(struct irq_domain *d,
+				       struct irq_fwspec *fwspec,
+				       irq_hw_number_t *hwirq,
+				       unsigned int *type)
 {
-	struct thunderx_gpio *txgpio = gpiochip_get_data(gc);
-
-	*parent = txgpio->base_msi + (2 * child);
-	*parent_type = IRQ_TYPE_LEVEL_HIGH;
+	struct thunderx_gpio *txgpio = d->host_data;
+
+	if (WARN_ON(fwspec->param_count < 2))
+		return -EINVAL;
+	if (fwspec->param[0] >= txgpio->chip.ngpio)
+		return -EINVAL;
+	*hwirq = fwspec->param[0];
+	*type = fwspec->param[1] & IRQ_TYPE_SENSE_MASK;
 	return 0;
 }
 
+static int thunderx_gpio_irq_alloc(struct irq_domain *d, unsigned int virq,
+				   unsigned int nr_irqs, void *arg)
+{
+	struct thunderx_line *txline = arg;
+
+	return irq_domain_set_hwirq_and_chip(d, virq, txline->line,
+					     &thunderx_gpio_irq_chip, txline);
+}
+
+static const struct irq_domain_ops thunderx_gpio_irqd_ops = {
+	.alloc		= thunderx_gpio_irq_alloc,
+	.translate	= thunderx_gpio_irq_translate
+};
+
+static int thunderx_gpio_to_irq(struct gpio_chip *chip, unsigned int offset)
+{
+	struct thunderx_gpio *txgpio = gpiochip_get_data(chip);
+
+	return irq_find_mapping(txgpio->irqd, offset);
+}
+
 static int thunderx_gpio_probe(struct pci_dev *pdev,
 			       const struct pci_device_id *id)
 {
@@ -405,7 +453,6 @@ static int thunderx_gpio_probe(struct pci_dev *pdev,
 	struct device *dev = &pdev->dev;
 	struct thunderx_gpio *txgpio;
 	struct gpio_chip *chip;
-	struct gpio_irq_chip *girq;
 	int ngpio, i;
 	int err = 0;
 
@@ -450,8 +497,8 @@ static int thunderx_gpio_probe(struct pci_dev *pdev,
 	}
 
 	txgpio->msix_entries = devm_kcalloc(dev,
-					    ngpio, sizeof(struct msix_entry),
-					    GFP_KERNEL);
+					  ngpio, sizeof(struct msix_entry),
+					  GFP_KERNEL);
 	if (!txgpio->msix_entries) {
 		err = -ENOMEM;
 		goto out;
@@ -492,6 +539,27 @@ static int thunderx_gpio_probe(struct pci_dev *pdev,
 	if (err < 0)
 		goto out;
 
+	/*
+	 * Push GPIO specific irqdomain on hierarchy created as a side
+	 * effect of the pci_enable_msix()
+	 */
+	txgpio->irqd = irq_domain_create_hierarchy(irq_get_irq_data(txgpio->msix_entries[0].vector)->domain,
+						   0, 0, of_node_to_fwnode(dev->of_node),
+						   &thunderx_gpio_irqd_ops, txgpio);
+	if (!txgpio->irqd) {
+		err = -ENOMEM;
+		goto out;
+	}
+
+	/* Push on irq_data and the domain for each line. */
+	for (i = 0; i < ngpio; i++) {
+		err = irq_domain_push_irq(txgpio->irqd,
+					  txgpio->msix_entries[i].vector,
+					  &txgpio->line_entries[i]);
+		if (err < 0)
+			dev_err(dev, "irq_domain_push_irq: %d\n", err);
+	}
+
 	chip->label = KBUILD_MODNAME;
 	chip->parent = dev;
 	chip->owner = THIS_MODULE;
@@ -506,28 +574,11 @@ static int thunderx_gpio_probe(struct pci_dev *pdev,
 	chip->set = thunderx_gpio_set;
 	chip->set_multiple = thunderx_gpio_set_multiple;
 	chip->set_config = thunderx_gpio_set_config;
-	girq = &chip->irq;
-	girq->chip = &thunderx_gpio_irq_chip;
-	girq->fwnode = of_node_to_fwnode(dev->of_node);
-	girq->parent_domain =
-		irq_get_irq_data(txgpio->msix_entries[0].vector)->domain;
-	girq->child_to_parent_hwirq = thunderx_gpio_child_to_parent_hwirq;
-	girq->handler = handle_bad_irq;
-	girq->default_type = IRQ_TYPE_NONE;
-
+	chip->to_irq = thunderx_gpio_to_irq;
 	err = devm_gpiochip_add_data(dev, chip, txgpio);
 	if (err)
 		goto out;
 
-	/* Push on irq_data and the domain for each line. */
-	for (i = 0; i < ngpio; i++) {
-		err = irq_domain_push_irq(chip->irq.domain,
-					  txgpio->msix_entries[i].vector,
-					  chip);
-		if (err < 0)
-			dev_err(dev, "irq_domain_push_irq: %d\n", err);
-	}
-
 	dev_info(dev, "ThunderX GPIO: %d lines with base %d.\n",
 		 ngpio, chip->base);
 	return 0;
@@ -542,10 +593,10 @@ static void thunderx_gpio_remove(struct pci_dev *pdev)
 	struct thunderx_gpio *txgpio = pci_get_drvdata(pdev);
 
 	for (i = 0; i < txgpio->chip.ngpio; i++)
-		irq_domain_pop_irq(txgpio->chip.irq.domain,
+		irq_domain_pop_irq(txgpio->irqd,
 				   txgpio->msix_entries[i].vector);
 
-	irq_domain_remove(txgpio->chip.irq.domain);
+	irq_domain_remove(txgpio->irqd);
 
 	pci_set_drvdata(pdev, NULL);
 }
-- 
2.20.1

[PATCH AUTOSEL 5.4 075/107] mlxsw: spectrum: Do not modify cloned SKBs during xmit

[Sasha Levin]

From: Ido Schimmel <idosch@mellanox.com>

[ Upstream commit 2da51ce75d86ab1f7770ac1391a9a1697ddaa60c ]

The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.

The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.

For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:

t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
     swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
     swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
     swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
     swp2

Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.

Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.

v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom

Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/mellanox/mlxsw/spectrum.c | 18 ++++++------------
 1 file changed, 6 insertions(+), 12 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
index 3ec18fb0d479c..45f6836fcc629 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
@@ -812,23 +812,17 @@ static netdev_tx_t mlxsw_sp_port_xmit(struct sk_buff *skb,
 	u64 len;
 	int err;
 
+	if (skb_cow_head(skb, MLXSW_TXHDR_LEN)) {
+		this_cpu_inc(mlxsw_sp_port->pcpu_stats->tx_dropped);
+		dev_kfree_skb_any(skb);
+		return NETDEV_TX_OK;
+	}
+
 	memset(skb->cb, 0, sizeof(struct mlxsw_skb_cb));
 
 	if (mlxsw_core_skb_transmit_busy(mlxsw_sp->core, &tx_info))
 		return NETDEV_TX_BUSY;
 
-	if (unlikely(skb_headroom(skb) < MLXSW_TXHDR_LEN)) {
-		struct sk_buff *skb_orig = skb;
-
-		skb = skb_realloc_headroom(skb, MLXSW_TXHDR_LEN);
-		if (!skb) {
-			this_cpu_inc(mlxsw_sp_port->pcpu_stats->tx_dropped);
-			dev_kfree_skb_any(skb_orig);
-			return NETDEV_TX_OK;
-		}
-		dev_consume_skb_any(skb_orig);
-	}
-
 	if (eth_skb_pad(skb)) {
 		this_cpu_inc(mlxsw_sp_port->pcpu_stats->tx_dropped);
 		return NETDEV_TX_OK;
-- 
2.20.1

[PATCH AUTOSEL 5.4 076/107] mlxsw: switchx2: Do not modify cloned SKBs during xmit

[Sasha Levin]

From: Ido Schimmel <idosch@mellanox.com>

[ Upstream commit 63963d0f9d17be83d0e419e03282847ecc2c3715 ]

The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.

The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.

For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:

t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
     swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
     swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
     swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
     swp2

Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.

Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.

v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom

Fixes: 31557f0f9755 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/mellanox/mlxsw/switchx2.c | 17 ++++++-----------
 1 file changed, 6 insertions(+), 11 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/switchx2.c b/drivers/net/ethernet/mellanox/mlxsw/switchx2.c
index 1c14c051ee525..63e7a058b7c6a 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/switchx2.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/switchx2.c
@@ -299,22 +299,17 @@ static netdev_tx_t mlxsw_sx_port_xmit(struct sk_buff *skb,
 	u64 len;
 	int err;
 
+	if (skb_cow_head(skb, MLXSW_TXHDR_LEN)) {
+		this_cpu_inc(mlxsw_sx_port->pcpu_stats->tx_dropped);
+		dev_kfree_skb_any(skb);
+		return NETDEV_TX_OK;
+	}
+
 	memset(skb->cb, 0, sizeof(struct mlxsw_skb_cb));
 
 	if (mlxsw_core_skb_transmit_busy(mlxsw_sx->core, &tx_info))
 		return NETDEV_TX_BUSY;
 
-	if (unlikely(skb_headroom(skb) < MLXSW_TXHDR_LEN)) {
-		struct sk_buff *skb_orig = skb;
-
-		skb = skb_realloc_headroom(skb, MLXSW_TXHDR_LEN);
-		if (!skb) {
-			this_cpu_inc(mlxsw_sx_port->pcpu_stats->tx_dropped);
-			dev_kfree_skb_any(skb_orig);
-			return NETDEV_TX_OK;
-		}
-		dev_consume_skb_any(skb_orig);
-	}
 	mlxsw_sx_txhdr_construct(skb, &tx_info);
 	/* TX header is consumed by HW on the way so we shouldn't count its
 	 * bytes as being sent.
-- 
2.20.1

[PATCH AUTOSEL 5.4 077/107] selftests: mlxsw: qos_mc_aware: Fix mausezahn invocation

[Sasha Levin]

From: Petr Machata <petrm@mellanox.com>

[ Upstream commit fef6d6704944c7be72fd2b77c021f1aed3d5df0d ]

Mausezahn does not recognize "own" as a keyword on source IP address. As a
result, the MC stream is not running at all, and therefore no UC
degradation can be observed even in principle.

Fix the invocation, and tighten the test: due to the minimum shaper
configured at the MC TCs, we always expect about 20% degradation. Fail the
test if it is lower.

Fixes: 573363a68f27 ("selftests: mlxsw: Add qos_lib.sh")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reported-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/testing/selftests/drivers/net/mlxsw/qos_mc_aware.sh | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/tools/testing/selftests/drivers/net/mlxsw/qos_mc_aware.sh b/tools/testing/selftests/drivers/net/mlxsw/qos_mc_aware.sh
index 47315fe48d5af..24dd8ed485802 100755
--- a/tools/testing/selftests/drivers/net/mlxsw/qos_mc_aware.sh
+++ b/tools/testing/selftests/drivers/net/mlxsw/qos_mc_aware.sh
@@ -232,7 +232,7 @@ test_mc_aware()
 	stop_traffic
 	local ucth1=${uc_rate[1]}
 
-	start_traffic $h1 own bc bc
+	start_traffic $h1 192.0.2.65 bc bc
 
 	local d0=$(date +%s)
 	local t0=$(ethtool_stats_get $h3 rx_octets_prio_0)
@@ -254,7 +254,11 @@ test_mc_aware()
 			ret = 100 * ($ucth1 - $ucth2) / $ucth1
 			if (ret > 0) { ret } else { 0 }
 		    ")
-	check_err $(bc <<< "$deg > 25")
+
+	# Minimum shaper of 200Mbps on MC TCs should cause about 20% of
+	# degradation on 1Gbps link.
+	check_err $(bc <<< "$deg < 15") "Minimum shaper not in effect"
+	check_err $(bc <<< "$deg > 25") "MC traffic degrades UC performance too much"
 
 	local interval=$((d1 - d0))
 	local mc_ir=$(rate $u0 $u1 $interval)
-- 
2.20.1

[PATCH AUTOSEL 5.4 078/107] mlxsw: spectrum: Wipe xstats.backlog of down ports

[Sasha Levin]

From: Petr Machata <petrm@mellanox.com>

[ Upstream commit ca7609ff3680c51d6c29897f3117aa2ad904f92a ]

Per-port counter cache used by Qdiscs is updated periodically, unless the
port is down. The fact that the cache is not updated for down ports is no
problem for most counters, which are relative in nature. However, backlog
is absolute in nature, and if there is a non-zero value in the cache around
the time that the port goes down, that value just stays there. This value
then leaks to offloaded Qdiscs that report non-zero backlog even if
there (obviously) is no traffic.

The HW does not keep backlog of a downed port, so do likewise: as the port
goes down, wipe the backlog value from xstats.

Fixes: 075ab8adaf4e ("mlxsw: spectrum: Collect tclass related stats periodically")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/mellanox/mlxsw/spectrum.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
index 45f6836fcc629..a806c6190bb1e 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
@@ -1161,6 +1161,9 @@ static void update_stats_cache(struct work_struct *work)
 			     periodic_hw_stats.update_dw.work);
 
 	if (!netif_carrier_ok(mlxsw_sp_port->dev))
+		/* Note: mlxsw_sp_port_down_wipe_counters() clears the cache as
+		 * necessary when port goes down.
+		 */
 		goto out;
 
 	mlxsw_sp_port_get_hw_stats(mlxsw_sp_port->dev,
@@ -4170,6 +4173,15 @@ static int mlxsw_sp_port_unsplit(struct mlxsw_core *mlxsw_core, u8 local_port,
 	return 0;
 }
 
+static void
+mlxsw_sp_port_down_wipe_counters(struct mlxsw_sp_port *mlxsw_sp_port)
+{
+	int i;
+
+	for (i = 0; i < TC_MAX_QUEUE; i++)
+		mlxsw_sp_port->periodic_hw_stats.xstats.backlog[i] = 0;
+}
+
 static void mlxsw_sp_pude_event_func(const struct mlxsw_reg_info *reg,
 				     char *pude_pl, void *priv)
 {
@@ -4191,6 +4203,7 @@ static void mlxsw_sp_pude_event_func(const struct mlxsw_reg_info *reg,
 	} else {
 		netdev_info(mlxsw_sp_port->dev, "link down\n");
 		netif_carrier_off(mlxsw_sp_port->dev);
+		mlxsw_sp_port_down_wipe_counters(mlxsw_sp_port);
 	}
 }
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 079/107] i2c: iop3xx: Fix memory leak in probe error path

[Sasha Levin]

From: Krzysztof Kozlowski <krzk@kernel.org>

[ Upstream commit e64175776d06a8ceebbfd349d7e66a4a46ca39ef ]

When handling devm_gpiod_get_optional() errors, free the memory already
allocated.  This fixes Smatch warnings:

    drivers/i2c/busses/i2c-iop3xx.c:437 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter'
    drivers/i2c/busses/i2c-iop3xx.c:442 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter'

Fixes: fdb7e884ad61 ("i2c: iop: Use GPIO descriptors")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/i2c/busses/i2c-iop3xx.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/drivers/i2c/busses/i2c-iop3xx.c b/drivers/i2c/busses/i2c-iop3xx.c
index 38556381f4cad..2f8b8050a2233 100644
--- a/drivers/i2c/busses/i2c-iop3xx.c
+++ b/drivers/i2c/busses/i2c-iop3xx.c
@@ -433,13 +433,17 @@ iop3xx_i2c_probe(struct platform_device *pdev)
 	adapter_data->gpio_scl = devm_gpiod_get_optional(&pdev->dev,
 							 "scl",
 							 GPIOD_ASIS);
-	if (IS_ERR(adapter_data->gpio_scl))
-		return PTR_ERR(adapter_data->gpio_scl);
+	if (IS_ERR(adapter_data->gpio_scl)) {
+		ret = PTR_ERR(adapter_data->gpio_scl);
+		goto free_both;
+	}
 	adapter_data->gpio_sda = devm_gpiod_get_optional(&pdev->dev,
 							 "sda",
 							 GPIOD_ASIS);
-	if (IS_ERR(adapter_data->gpio_sda))
-		return PTR_ERR(adapter_data->gpio_sda);
+	if (IS_ERR(adapter_data->gpio_sda)) {
+		ret = PTR_ERR(adapter_data->gpio_sda);
+		goto free_both;
+	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 080/107] Fix built-in early-load Intel microcode alignment

[Sasha Levin]

From: Jari Ruusu <jari.ruusu@gmail.com>

[ Upstream commit f5ae2ea6347a308cfe91f53b53682ce635497d0d ]

Intel Software Developer's Manual, volume 3, chapter 9.11.6 says:

 "Note that the microcode update must be aligned on a 16-byte boundary
  and the size of the microcode update must be 1-KByte granular"

When early-load Intel microcode is loaded from initramfs, userspace tool
'iucode_tool' has already 16-byte aligned those microcode bits in that
initramfs image.  Image that was created something like this:

 iucode_tool --write-earlyfw=FOO.cpio microcode-files...

However, when early-load Intel microcode is loaded from built-in
firmware BLOB using CONFIG_EXTRA_FIRMWARE= kernel config option, that
16-byte alignment is not guaranteed.

Fix this by forcing all built-in firmware BLOBs to 16-byte alignment.

[ If we end up having other firmware with much bigger alignment
  requirements, we might need to introduce some method for the firmware
  to specify it, this is the minimal "just increase the alignment a bit
  to account for this one special case" patch    - Linus ]

Signed-off-by: Jari Ruusu <jari.ruusu@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/base/firmware_loader/builtin/Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/base/firmware_loader/builtin/Makefile b/drivers/base/firmware_loader/builtin/Makefile
index 4a66888e7253d..5fa7ce3745a0d 100644
--- a/drivers/base/firmware_loader/builtin/Makefile
+++ b/drivers/base/firmware_loader/builtin/Makefile
@@ -17,7 +17,7 @@ PROGBITS  = $(if $(CONFIG_ARM),%,@)progbits
 filechk_fwbin = \
 	echo "/* Generated by $(src)/Makefile */"		;\
 	echo "    .section .rodata"				;\
-	echo "    .p2align $(ASM_ALIGN)"			;\
+	echo "    .p2align 4"					;\
 	echo "_fw_$(FWSTR)_bin:"				;\
 	echo "    .incbin \"$(fwdir)/$(FWNAME)\""		;\
 	echo "_fw_end:"						;\
-- 
2.20.1

[PATCH AUTOSEL 5.4 081/107] hv_netvsc: Fix memory leak when removing rndis device

[Sasha Levin]

From: Mohammed Gamal <mgamal@redhat.com>

[ Upstream commit 536dc5df2808efbefc5acee334d3c4f701790ec0 ]

kmemleak detects the following memory leak when hot removing
a network device:

unreferenced object 0xffff888083f63600 (size 256):
  comm "kworker/0:1", pid 12, jiffies 4294831717 (age 1113.676s)
  hex dump (first 32 bytes):
    00 40 c7 33 80 88 ff ff 00 00 00 00 10 00 00 00  .@.3............
    00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00  .....N..........
  backtrace:
    [<00000000d4a8f5be>] rndis_filter_device_add+0x117/0x11c0 [hv_netvsc]
    [<000000009c02d75b>] netvsc_probe+0x5e7/0xbf0 [hv_netvsc]
    [<00000000ddafce23>] vmbus_probe+0x74/0x170 [hv_vmbus]
    [<00000000046e64f1>] really_probe+0x22f/0xb50
    [<000000005cc35eb7>] driver_probe_device+0x25e/0x370
    [<0000000043c642b2>] bus_for_each_drv+0x11f/0x1b0
    [<000000005e3d09f0>] __device_attach+0x1c6/0x2f0
    [<00000000a72c362f>] bus_probe_device+0x1a6/0x260
    [<0000000008478399>] device_add+0x10a3/0x18e0
    [<00000000cf07b48c>] vmbus_device_register+0xe7/0x1e0 [hv_vmbus]
    [<00000000d46cf032>] vmbus_add_channel_work+0x8ab/0x1770 [hv_vmbus]
    [<000000002c94bb64>] process_one_work+0x919/0x17d0
    [<0000000096de6781>] worker_thread+0x87/0xb40
    [<00000000fbe7397e>] kthread+0x333/0x3f0
    [<000000004f844269>] ret_from_fork+0x3a/0x50

rndis_filter_device_add() allocates an instance of struct rndis_device
which never gets deallocated as rndis_filter_device_remove() sets
net_device->extension which points to the rndis_device struct to NULL,
leaving the rndis_device dangling.

Since net_device->extension is eventually freed in free_netvsc_device(),
we refrain from setting it to NULL inside rndis_filter_device_remove()

Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/hyperv/rndis_filter.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/net/hyperv/rndis_filter.c b/drivers/net/hyperv/rndis_filter.c
index f81e58267a6ee..b9e44bb22289c 100644
--- a/drivers/net/hyperv/rndis_filter.c
+++ b/drivers/net/hyperv/rndis_filter.c
@@ -1436,8 +1436,6 @@ void rndis_filter_device_remove(struct hv_device *dev,
 	/* Halt and release the rndis device */
 	rndis_filter_halt_device(net_dev, rndis_dev);
 
-	net_dev->extension = NULL;
-
 	netvsc_device_remove(dev);
 }
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 081/107] hv_netvsc: Fix memory leak when removing rndis device

[Sasha Levin]

From: Mohammed Gamal <mgamal@redhat.com>

[ Upstream commit 536dc5df2808efbefc5acee334d3c4f701790ec0 ]

kmemleak detects the following memory leak when hot removing
a network device:

unreferenced object 0xffff888083f63600 (size 256):
  comm "kworker/0:1", pid 12, jiffies 4294831717 (age 1113.676s)
  hex dump (first 32 bytes):
    00 40 c7 33 80 88 ff ff 00 00 00 00 10 00 00 00  .@.3............
    00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00  .....N..........
  backtrace:
    [<00000000d4a8f5be>] rndis_filter_device_add+0x117/0x11c0 [hv_netvsc]
    [<000000009c02d75b>] netvsc_probe+0x5e7/0xbf0 [hv_netvsc]
    [<00000000ddafce23>] vmbus_probe+0x74/0x170 [hv_vmbus]
    [<00000000046e64f1>] really_probe+0x22f/0xb50
    [<000000005cc35eb7>] driver_probe_device+0x25e/0x370
    [<0000000043c642b2>] bus_for_each_drv+0x11f/0x1b0
    [<000000005e3d09f0>] __device_attach+0x1c6/0x2f0
    [<00000000a72c362f>] bus_probe_device+0x1a6/0x260
    [<0000000008478399>] device_add+0x10a3/0x18e0
    [<00000000cf07b48c>] vmbus_device_register+0xe7/0x1e0 [hv_vmbus]
    [<00000000d46cf032>] vmbus_add_channel_work+0x8ab/0x1770 [hv_vmbus]
    [<000000002c94bb64>] process_one_work+0x919/0x17d0
    [<0000000096de6781>] worker_thread+0x87/0xb40
    [<00000000fbe7397e>] kthread+0x333/0x3f0
    [<000000004f844269>] ret_from_fork+0x3a/0x50

rndis_filter_device_add() allocates an instance of struct rndis_device
which never gets deallocated as rndis_filter_device_remove() sets
net_device->extension which points to the rndis_device struct to NULL,
leaving the rndis_device dangling.

Since net_device->extension is eventually freed in free_netvsc_device(),
we refrain from setting it to NULL inside rndis_filter_device_remove()

Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/hyperv/rndis_filter.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/net/hyperv/rndis_filter.c b/drivers/net/hyperv/rndis_filter.c
index f81e58267a6ee..b9e44bb22289c 100644
--- a/drivers/net/hyperv/rndis_filter.c
+++ b/drivers/net/hyperv/rndis_filter.c
@@ -1436,8 +1436,6 @@ void rndis_filter_device_remove(struct hv_device *dev,
 	/* Halt and release the rndis device */
 	rndis_filter_halt_device(net_dev, rndis_dev);
 
-	net_dev->extension = NULL;
-
 	netvsc_device_remove(dev);
 }
 
-- 
2.20.1

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

[PATCH AUTOSEL 5.4 082/107] bpf: Fix incorrect verifier simulation of ARSH under ALU32

[Sasha Levin]

From: Daniel Borkmann <daniel@iogearbox.net>

[ Upstream commit 0af2ffc93a4b50948f9dad2786b7f1bd253bf0b9 ]

Anatoly has been fuzzing with kBdysch harness and reported a hang in one
of the outcomes:

  0: R1=ctx(id=0,off=0,imm=0) R10=fp0
  0: (85) call bpf_get_socket_cookie#46
  1: R0_w=invP(id=0) R10=fp0
  1: (57) r0 &= 808464432
  2: R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
  2: (14) w0 -= 810299440
  3: R0_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
  3: (c4) w0 s>>= 1
  4: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
  4: (76) if w0 s>= 0x30303030 goto pc+216
  221: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
  221: (95) exit
  processed 6 insns (limit 1000000) [...]

Taking a closer look, the program was xlated as follows:

  # ./bpftool p d x i 12
  0: (85) call bpf_get_socket_cookie#7800896
  1: (bf) r6 = r0
  2: (57) r6 &= 808464432
  3: (14) w6 -= 810299440
  4: (c4) w6 s>>= 1
  5: (76) if w6 s>= 0x30303030 goto pc+216
  6: (05) goto pc-1
  7: (05) goto pc-1
  8: (05) goto pc-1
  [...]
  220: (05) goto pc-1
  221: (05) goto pc-1
  222: (95) exit

Meaning, the visible effect is very similar to f54c7898ed1c ("bpf: Fix
precision tracking for unbounded scalars"), that is, the fall-through
branch in the instruction 5 is considered to be never taken given the
conclusion from the min/max bounds tracking in w6, and therefore the
dead-code sanitation rewrites it as goto pc-1. However, real-life input
disagrees with verification analysis since a soft-lockup was observed.

The bug sits in the analysis of the ARSH. The definition is that we shift
the target register value right by K bits through shifting in copies of
its sign bit. In adjust_scalar_min_max_vals(), we do first coerce the
register into 32 bit mode, same happens after simulating the operation.
However, for the case of simulating the actual ARSH, we don't take the
mode into account and act as if it's always 64 bit, but location of sign
bit is different:

  dst_reg->smin_value >>= umin_val;
  dst_reg->smax_value >>= umin_val;
  dst_reg->var_off = tnum_arshift(dst_reg->var_off, umin_val);

Consider an unknown R0 where bpf_get_socket_cookie() (or others) would
for example return 0xffff. With the above ARSH simulation, we'd see the
following results:

  [...]
  1: R1=ctx(id=0,off=0,imm=0) R2_w=invP65535 R10=fp0
  1: (85) call bpf_get_socket_cookie#46
  2: R0_w=invP(id=0) R10=fp0
  2: (57) r0 &= 808464432
    -> R0_runtime = 0x3030
  3: R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
  3: (14) w0 -= 810299440
    -> R0_runtime = 0xcfb40000
  4: R0_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
                              (0xffffffff)
  4: (c4) w0 s>>= 1
    -> R0_runtime = 0xe7da0000
  5: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
                              (0x67c00000)           (0x7ffbfff8)
  [...]

In insn 3, we have a runtime value of 0xcfb40000, which is '1100 1111 1011
0100 0000 0000 0000 0000', the result after the shift has 0xe7da0000 that
is '1110 0111 1101 1010 0000 0000 0000 0000', where the sign bit is correctly
retained in 32 bit mode. In insn4, the umax was 0xffffffff, and changed into
0x7ffbfff8 after the shift, that is, '0111 1111 1111 1011 1111 1111 1111 1000'
and means here that the simulation didn't retain the sign bit. With above
logic, the updates happen on the 64 bit min/max bounds and given we coerced
the register, the sign bits of the bounds are cleared as well, meaning, we
need to force the simulation into s32 space for 32 bit alu mode.

Verification after the fix below. We're first analyzing the fall-through branch
on 32 bit signed >= test eventually leading to rejection of the program in this
specific case:

  0: R1=ctx(id=0,off=0,imm=0) R10=fp0
  0: (b7) r2 = 808464432
  1: R1=ctx(id=0,off=0,imm=0) R2_w=invP808464432 R10=fp0
  1: (85) call bpf_get_socket_cookie#46
  2: R0_w=invP(id=0) R10=fp0
  2: (bf) r6 = r0
  3: R0_w=invP(id=0) R6_w=invP(id=0) R10=fp0
  3: (57) r6 &= 808464432
  4: R0_w=invP(id=0) R6_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
  4: (14) w6 -= 810299440
  5: R0_w=invP(id=0) R6_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
  5: (c4) w6 s>>= 1
  6: R0_w=invP(id=0) R6_w=invP(id=0,umin_value=3888119808,umax_value=4294705144,var_off=(0xe7c00000; 0x183bfff8)) R10=fp0
                                              (0x67c00000)          (0xfffbfff8)
  6: (76) if w6 s>= 0x30303030 goto pc+216
  7: R0_w=invP(id=0) R6_w=invP(id=0,umin_value=3888119808,umax_value=4294705144,var_off=(0xe7c00000; 0x183bfff8)) R10=fp0
  7: (30) r0 = *(u8 *)skb[808464432]
  BPF_LD_[ABS|IND] uses reserved fields
  processed 8 insns (limit 1000000) [...]

Fixes: 9cbe1f5a32dc ("bpf/verifier: improve register value range tracking with ARSH")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200115204733.16648-1-daniel@iogearbox.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/linux/tnum.h  |  2 +-
 kernel/bpf/tnum.c     |  9 +++++++--
 kernel/bpf/verifier.c | 13 ++++++++++---
 3 files changed, 18 insertions(+), 6 deletions(-)

diff --git a/include/linux/tnum.h b/include/linux/tnum.h
index c17af77f3fae7..ea627d1ab7e39 100644
--- a/include/linux/tnum.h
+++ b/include/linux/tnum.h
@@ -30,7 +30,7 @@ struct tnum tnum_lshift(struct tnum a, u8 shift);
 /* Shift (rsh) a tnum right (by a fixed shift) */
 struct tnum tnum_rshift(struct tnum a, u8 shift);
 /* Shift (arsh) a tnum right (by a fixed min_shift) */
-struct tnum tnum_arshift(struct tnum a, u8 min_shift);
+struct tnum tnum_arshift(struct tnum a, u8 min_shift, u8 insn_bitness);
 /* Add two tnums, return @a + @b */
 struct tnum tnum_add(struct tnum a, struct tnum b);
 /* Subtract two tnums, return @a - @b */
diff --git a/kernel/bpf/tnum.c b/kernel/bpf/tnum.c
index ca52b9642943f..d4f335a9a8998 100644
--- a/kernel/bpf/tnum.c
+++ b/kernel/bpf/tnum.c
@@ -44,14 +44,19 @@ struct tnum tnum_rshift(struct tnum a, u8 shift)
 	return TNUM(a.value >> shift, a.mask >> shift);
 }
 
-struct tnum tnum_arshift(struct tnum a, u8 min_shift)
+struct tnum tnum_arshift(struct tnum a, u8 min_shift, u8 insn_bitness)
 {
 	/* if a.value is negative, arithmetic shifting by minimum shift
 	 * will have larger negative offset compared to more shifting.
 	 * If a.value is nonnegative, arithmetic shifting by minimum shift
 	 * will have larger positive offset compare to more shifting.
 	 */
-	return TNUM((s64)a.value >> min_shift, (s64)a.mask >> min_shift);
+	if (insn_bitness == 32)
+		return TNUM((u32)(((s32)a.value) >> min_shift),
+			    (u32)(((s32)a.mask)  >> min_shift));
+	else
+		return TNUM((s64)a.value >> min_shift,
+			    (s64)a.mask  >> min_shift);
 }
 
 struct tnum tnum_add(struct tnum a, struct tnum b)
diff --git a/kernel/bpf/verifier.c b/kernel/bpf/verifier.c
index 9c74c98f65012..b2817d0929b39 100644
--- a/kernel/bpf/verifier.c
+++ b/kernel/bpf/verifier.c
@@ -4824,9 +4824,16 @@ static int adjust_scalar_min_max_vals(struct bpf_verifier_env *env,
 		/* Upon reaching here, src_known is true and
 		 * umax_val is equal to umin_val.
 		 */
-		dst_reg->smin_value >>= umin_val;
-		dst_reg->smax_value >>= umin_val;
-		dst_reg->var_off = tnum_arshift(dst_reg->var_off, umin_val);
+		if (insn_bitness == 32) {
+			dst_reg->smin_value = (u32)(((s32)dst_reg->smin_value) >> umin_val);
+			dst_reg->smax_value = (u32)(((s32)dst_reg->smax_value) >> umin_val);
+		} else {
+			dst_reg->smin_value >>= umin_val;
+			dst_reg->smax_value >>= umin_val;
+		}
+
+		dst_reg->var_off = tnum_arshift(dst_reg->var_off, umin_val,
+						insn_bitness);
 
 		/* blow away the dst_reg umin_value/umax_value and rely on
 		 * dst_reg var_off to refine the result.
-- 
2.20.1

[PATCH AUTOSEL 5.4 083/107] net/wan/fsl_ucc_hdlc: fix out of bounds write on array utdm_info

[Sasha Levin]

From: Colin Ian King <colin.king@canonical.com>

[ Upstream commit ddf420390526ede3b9ff559ac89f58cb59d9db2f ]

Array utdm_info is declared as an array of MAX_HDLC_NUM (4) elements
however up to UCC_MAX_NUM (8) elements are potentially being written
to it.  Currently we have an array out-of-bounds write error on the
last 4 elements. Fix this by making utdm_info UCC_MAX_NUM elements in
size.

Addresses-Coverity: ("Out-of-bounds write")
Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wan/fsl_ucc_hdlc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wan/fsl_ucc_hdlc.c b/drivers/net/wan/fsl_ucc_hdlc.c
index ca0f3be2b6bf8..aef7de225783f 100644
--- a/drivers/net/wan/fsl_ucc_hdlc.c
+++ b/drivers/net/wan/fsl_ucc_hdlc.c
@@ -73,7 +73,7 @@ static struct ucc_tdm_info utdm_primary_info = {
 	},
 };
 
-static struct ucc_tdm_info utdm_info[MAX_HDLC_NUM];
+static struct ucc_tdm_info utdm_info[UCC_MAX_NUM];
 
 static int uhdlc_init(struct ucc_hdlc_private *priv)
 {
-- 
2.20.1

[PATCH AUTOSEL 5.4 084/107] net: stmmac: selftests: Make it work in Synopsys AXS101 boards

[Sasha Levin]

From: Jose Abreu <Jose.Abreu@synopsys.com>

[ Upstream commit 0b9f932edc1a461933bfde08e620362e2190e0dd ]

Synopsys AXS101 boards do not support unaligned memory loads or stores.
Change the selftests mechanism to explicity:
- Not add extra alignment in TX SKB
- Use the unaligned version of ether_addr_equal()

Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../stmicro/stmmac/stmmac_selftests.c         | 20 ++++++++++---------
 1 file changed, 11 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
index 3679d123a2ab7..36ef8bee5fcfd 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
@@ -80,7 +80,7 @@ static struct sk_buff *stmmac_test_get_udp_skb(struct stmmac_priv *priv,
 	if (attr->max_size && (attr->max_size > size))
 		size = attr->max_size;
 
-	skb = netdev_alloc_skb_ip_align(priv->dev, size);
+	skb = netdev_alloc_skb(priv->dev, size);
 	if (!skb)
 		return NULL;
 
@@ -244,6 +244,8 @@ static int stmmac_test_loopback_validate(struct sk_buff *skb,
 					 struct net_device *orig_ndev)
 {
 	struct stmmac_test_priv *tpriv = pt->af_packet_priv;
+	unsigned char *src = tpriv->packet->src;
+	unsigned char *dst = tpriv->packet->dst;
 	struct stmmachdr *shdr;
 	struct ethhdr *ehdr;
 	struct udphdr *uhdr;
@@ -260,15 +262,15 @@ static int stmmac_test_loopback_validate(struct sk_buff *skb,
 		goto out;
 
 	ehdr = (struct ethhdr *)skb_mac_header(skb);
-	if (tpriv->packet->dst) {
-		if (!ether_addr_equal(ehdr->h_dest, tpriv->packet->dst))
+	if (dst) {
+		if (!ether_addr_equal_unaligned(ehdr->h_dest, dst))
 			goto out;
 	}
 	if (tpriv->packet->sarc) {
-		if (!ether_addr_equal(ehdr->h_source, ehdr->h_dest))
+		if (!ether_addr_equal_unaligned(ehdr->h_source, ehdr->h_dest))
 			goto out;
-	} else if (tpriv->packet->src) {
-		if (!ether_addr_equal(ehdr->h_source, tpriv->packet->src))
+	} else if (src) {
+		if (!ether_addr_equal_unaligned(ehdr->h_source, src))
 			goto out;
 	}
 
@@ -714,7 +716,7 @@ static int stmmac_test_flowctrl_validate(struct sk_buff *skb,
 	struct ethhdr *ehdr;
 
 	ehdr = (struct ethhdr *)skb_mac_header(skb);
-	if (!ether_addr_equal(ehdr->h_source, orig_ndev->dev_addr))
+	if (!ether_addr_equal_unaligned(ehdr->h_source, orig_ndev->dev_addr))
 		goto out;
 	if (ehdr->h_proto != htons(ETH_P_PAUSE))
 		goto out;
@@ -856,7 +858,7 @@ static int stmmac_test_vlan_validate(struct sk_buff *skb,
 	}
 
 	ehdr = (struct ethhdr *)skb_mac_header(skb);
-	if (!ether_addr_equal(ehdr->h_dest, tpriv->packet->dst))
+	if (!ether_addr_equal_unaligned(ehdr->h_dest, tpriv->packet->dst))
 		goto out;
 
 	ihdr = ip_hdr(skb);
@@ -1554,7 +1556,7 @@ static int stmmac_test_arp_validate(struct sk_buff *skb,
 	struct arphdr *ahdr;
 
 	ehdr = (struct ethhdr *)skb_mac_header(skb);
-	if (!ether_addr_equal(ehdr->h_dest, tpriv->packet->src))
+	if (!ether_addr_equal_unaligned(ehdr->h_dest, tpriv->packet->src))
 		goto out;
 
 	ahdr = arp_hdr(skb);
-- 
2.20.1

[PATCH AUTOSEL 5.4 085/107] net: stmmac: selftests: Mark as fail when received VLAN ID != expected

[Sasha Levin]

From: Jose Abreu <Jose.Abreu@synopsys.com>

[ Upstream commit d39b68e5a736afa67d2e9cfb158efdd237d99dbd ]

When the VLAN ID does not match the expected one it means filter failed
in HW. Fix it.

Fixes: 94e18382003c ("net: stmmac: selftests: Add selftest for VLAN TX Offload")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
index 36ef8bee5fcfd..ba03a2d774344 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c
@@ -853,8 +853,12 @@ static int stmmac_test_vlan_validate(struct sk_buff *skb,
 	if (tpriv->vlan_id) {
 		if (skb->vlan_proto != htons(proto))
 			goto out;
-		if (skb->vlan_tci != tpriv->vlan_id)
+		if (skb->vlan_tci != tpriv->vlan_id) {
+			/* Means filter did not work. */
+			tpriv->ok = false;
+			complete(&tpriv->comp);
 			goto out;
+		}
 	}
 
 	ehdr = (struct ethhdr *)skb_mac_header(skb);
-- 
2.20.1

[PATCH AUTOSEL 5.4 086/107] scsi: storvsc: Correctly set number of hardware queues for IDE disk

[Sasha Levin]

From: Long Li <longli@microsoft.com>

[ Upstream commit 7b571c19d4c0b78d27dd3bf1f3c42e4032390af6 ]

Commit 0ed881027690 ("scsi: storvsc: setup 1:1 mapping between hardware
queue and CPU queue") introduced a regression for disks attached to
IDE. For these disks the host VSP only offers one VMBUS channel. Setting
multiple queues can overload the VMBUS channel and result in performance
drop for high queue depth workload on system with large number of CPUs.

Fix it by leaving the number of hardware queues to 1 (default value) for
IDE disks.

Fixes: 0ed881027690 ("scsi: storvsc: setup 1:1 mapping between hardware queue and CPU queue")
Link: https://lore.kernel.org/r/1578960516-108228-1-git-send-email-longli@linuxonhyperv.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/storvsc_drv.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/storvsc_drv.c b/drivers/scsi/storvsc_drv.c
index 542d2bac2922c..5087ed6afbdc3 100644
--- a/drivers/scsi/storvsc_drv.c
+++ b/drivers/scsi/storvsc_drv.c
@@ -1835,9 +1835,11 @@ static int storvsc_probe(struct hv_device *device,
 	 */
 	host->sg_tablesize = (stor_device->max_transfer_bytes >> PAGE_SHIFT);
 	/*
+	 * For non-IDE disks, the host supports multiple channels.
 	 * Set the number of HW queues we are supporting.
 	 */
-	host->nr_hw_queues = num_present_cpus();
+	if (!dev_is_ide)
+		host->nr_hw_queues = num_present_cpus();
 
 	/*
 	 * Set the error handler work queue.
-- 
2.20.1

[PATCH AUTOSEL 5.4 086/107] scsi: storvsc: Correctly set number of hardware queues for IDE disk

[Sasha Levin]

From: Long Li <longli@microsoft.com>

[ Upstream commit 7b571c19d4c0b78d27dd3bf1f3c42e4032390af6 ]

Commit 0ed881027690 ("scsi: storvsc: setup 1:1 mapping between hardware
queue and CPU queue") introduced a regression for disks attached to
IDE. For these disks the host VSP only offers one VMBUS channel. Setting
multiple queues can overload the VMBUS channel and result in performance
drop for high queue depth workload on system with large number of CPUs.

Fix it by leaving the number of hardware queues to 1 (default value) for
IDE disks.

Fixes: 0ed881027690 ("scsi: storvsc: setup 1:1 mapping between hardware queue and CPU queue")
Link: https://lore.kernel.org/r/1578960516-108228-1-git-send-email-longli@linuxonhyperv.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/storvsc_drv.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/storvsc_drv.c b/drivers/scsi/storvsc_drv.c
index 542d2bac2922c..5087ed6afbdc3 100644
--- a/drivers/scsi/storvsc_drv.c
+++ b/drivers/scsi/storvsc_drv.c
@@ -1835,9 +1835,11 @@ static int storvsc_probe(struct hv_device *device,
 	 */
 	host->sg_tablesize = (stor_device->max_transfer_bytes >> PAGE_SHIFT);
 	/*
+	 * For non-IDE disks, the host supports multiple channels.
 	 * Set the number of HW queues we are supporting.
 	 */
-	host->nr_hw_queues = num_present_cpus();
+	if (!dev_is_ide)
+		host->nr_hw_queues = num_present_cpus();
 
 	/*
 	 * Set the error handler work queue.
-- 
2.20.1

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

[PATCH AUTOSEL 5.4 087/107] scsi: mptfusion: Fix double fetch bug in ioctl

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 28d76df18f0ad5bcf5fa48510b225f0ed262a99b ]

Tom Hatskevich reported that we look up "iocp" then, in the called
functions we do a second copy_from_user() and look it up again.
The problem that could cause is:

drivers/message/fusion/mptctl.c
   674          /* All of these commands require an interrupt or
   675           * are unknown/illegal.
   676           */
   677          if ((ret = mptctl_syscall_down(iocp, nonblock)) != 0)
                                               ^^^^
We take this lock.

   678                  return ret;
   679
   680          if (cmd == MPTFWDOWNLOAD)
   681                  ret = mptctl_fw_download(arg);
                                                 ^^^
Then the user memory changes and we look up "iocp" again but a different
one so now we are holding the incorrect lock and have a race condition.

   682          else if (cmd == MPTCOMMAND)
   683                  ret = mptctl_mpt_command(arg);

The security impact of this bug is not as bad as it could have been
because these operations are all privileged and root already has
enormous destructive power.  But it's still worth fixing.

This patch passes the "iocp" pointer to the functions to avoid the
second lookup.  That deletes 100 lines of code from the driver so
it's a nice clean up as well.

Link: https://lore.kernel.org/r/20200114123414.GA7957@kadam
Reported-by: Tom Hatskevich <tom2001tom.23@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/message/fusion/mptctl.c | 213 ++++++++------------------------
 1 file changed, 50 insertions(+), 163 deletions(-)

diff --git a/drivers/message/fusion/mptctl.c b/drivers/message/fusion/mptctl.c
index f9ac224130008..1074b882c57c8 100644
--- a/drivers/message/fusion/mptctl.c
+++ b/drivers/message/fusion/mptctl.c
@@ -100,19 +100,19 @@ struct buflist {
  * Function prototypes. Called from OS entry point mptctl_ioctl.
  * arg contents specific to function.
  */
-static int mptctl_fw_download(unsigned long arg);
-static int mptctl_getiocinfo(unsigned long arg, unsigned int cmd);
-static int mptctl_gettargetinfo(unsigned long arg);
-static int mptctl_readtest(unsigned long arg);
-static int mptctl_mpt_command(unsigned long arg);
-static int mptctl_eventquery(unsigned long arg);
-static int mptctl_eventenable(unsigned long arg);
-static int mptctl_eventreport(unsigned long arg);
-static int mptctl_replace_fw(unsigned long arg);
-
-static int mptctl_do_reset(unsigned long arg);
-static int mptctl_hp_hostinfo(unsigned long arg, unsigned int cmd);
-static int mptctl_hp_targetinfo(unsigned long arg);
+static int mptctl_fw_download(MPT_ADAPTER *iocp, unsigned long arg);
+static int mptctl_getiocinfo(MPT_ADAPTER *iocp, unsigned long arg, unsigned int cmd);
+static int mptctl_gettargetinfo(MPT_ADAPTER *iocp, unsigned long arg);
+static int mptctl_readtest(MPT_ADAPTER *iocp, unsigned long arg);
+static int mptctl_mpt_command(MPT_ADAPTER *iocp, unsigned long arg);
+static int mptctl_eventquery(MPT_ADAPTER *iocp, unsigned long arg);
+static int mptctl_eventenable(MPT_ADAPTER *iocp, unsigned long arg);
+static int mptctl_eventreport(MPT_ADAPTER *iocp, unsigned long arg);
+static int mptctl_replace_fw(MPT_ADAPTER *iocp, unsigned long arg);
+
+static int mptctl_do_reset(MPT_ADAPTER *iocp, unsigned long arg);
+static int mptctl_hp_hostinfo(MPT_ADAPTER *iocp, unsigned long arg, unsigned int cmd);
+static int mptctl_hp_targetinfo(MPT_ADAPTER *iocp, unsigned long arg);
 
 static int  mptctl_probe(struct pci_dev *, const struct pci_device_id *);
 static void mptctl_remove(struct pci_dev *);
@@ -123,8 +123,8 @@ static long compat_mpctl_ioctl(struct file *f, unsigned cmd, unsigned long arg);
 /*
  * Private function calls.
  */
-static int mptctl_do_mpt_command(struct mpt_ioctl_command karg, void __user *mfPtr);
-static int mptctl_do_fw_download(int ioc, char __user *ufwbuf, size_t fwlen);
+static int mptctl_do_mpt_command(MPT_ADAPTER *iocp, struct mpt_ioctl_command karg, void __user *mfPtr);
+static int mptctl_do_fw_download(MPT_ADAPTER *iocp, char __user *ufwbuf, size_t fwlen);
 static MptSge_t *kbuf_alloc_2_sgl(int bytes, u32 dir, int sge_offset, int *frags,
 		struct buflist **blp, dma_addr_t *sglbuf_dma, MPT_ADAPTER *ioc);
 static void kfree_sgl(MptSge_t *sgl, dma_addr_t sgl_dma,
@@ -656,19 +656,19 @@ __mptctl_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 	 * by TM and FW reloads.
 	 */
 	if ((cmd & ~IOCSIZE_MASK) == (MPTIOCINFO & ~IOCSIZE_MASK)) {
-		return mptctl_getiocinfo(arg, _IOC_SIZE(cmd));
+		return mptctl_getiocinfo(iocp, arg, _IOC_SIZE(cmd));
 	} else if (cmd == MPTTARGETINFO) {
-		return mptctl_gettargetinfo(arg);
+		return mptctl_gettargetinfo(iocp, arg);
 	} else if (cmd == MPTTEST) {
-		return mptctl_readtest(arg);
+		return mptctl_readtest(iocp, arg);
 	} else if (cmd == MPTEVENTQUERY) {
-		return mptctl_eventquery(arg);
+		return mptctl_eventquery(iocp, arg);
 	} else if (cmd == MPTEVENTENABLE) {
-		return mptctl_eventenable(arg);
+		return mptctl_eventenable(iocp, arg);
 	} else if (cmd == MPTEVENTREPORT) {
-		return mptctl_eventreport(arg);
+		return mptctl_eventreport(iocp, arg);
 	} else if (cmd == MPTFWREPLACE) {
-		return mptctl_replace_fw(arg);
+		return mptctl_replace_fw(iocp, arg);
 	}
 
 	/* All of these commands require an interrupt or
@@ -678,15 +678,15 @@ __mptctl_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 		return ret;
 
 	if (cmd == MPTFWDOWNLOAD)
-		ret = mptctl_fw_download(arg);
+		ret = mptctl_fw_download(iocp, arg);
 	else if (cmd == MPTCOMMAND)
-		ret = mptctl_mpt_command(arg);
+		ret = mptctl_mpt_command(iocp, arg);
 	else if (cmd == MPTHARDRESET)
-		ret = mptctl_do_reset(arg);
+		ret = mptctl_do_reset(iocp, arg);
 	else if ((cmd & ~IOCSIZE_MASK) == (HP_GETHOSTINFO & ~IOCSIZE_MASK))
-		ret = mptctl_hp_hostinfo(arg, _IOC_SIZE(cmd));
+		ret = mptctl_hp_hostinfo(iocp, arg, _IOC_SIZE(cmd));
 	else if (cmd == HP_GETTARGETINFO)
-		ret = mptctl_hp_targetinfo(arg);
+		ret = mptctl_hp_targetinfo(iocp, arg);
 	else
 		ret = -EINVAL;
 
@@ -705,11 +705,10 @@ mptctl_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 	return ret;
 }
 
-static int mptctl_do_reset(unsigned long arg)
+static int mptctl_do_reset(MPT_ADAPTER *iocp, unsigned long arg)
 {
 	struct mpt_ioctl_diag_reset __user *urinfo = (void __user *) arg;
 	struct mpt_ioctl_diag_reset krinfo;
-	MPT_ADAPTER		*iocp;
 
 	if (copy_from_user(&krinfo, urinfo, sizeof(struct mpt_ioctl_diag_reset))) {
 		printk(KERN_ERR MYNAM "%s@%d::mptctl_do_reset - "
@@ -718,12 +717,6 @@ static int mptctl_do_reset(unsigned long arg)
 		return -EFAULT;
 	}
 
-	if (mpt_verify_adapter(krinfo.hdr.iocnum, &iocp) < 0) {
-		printk(KERN_DEBUG MYNAM "%s@%d::mptctl_do_reset - ioc%d not found!\n",
-				__FILE__, __LINE__, krinfo.hdr.iocnum);
-		return -ENODEV; /* (-6) No such device or address */
-	}
-
 	dctlprintk(iocp, printk(MYIOC_s_DEBUG_FMT "mptctl_do_reset called.\n",
 	    iocp->name));
 
@@ -754,7 +747,7 @@ static int mptctl_do_reset(unsigned long arg)
  *		-ENOMSG if FW upload returned bad status
  */
 static int
-mptctl_fw_download(unsigned long arg)
+mptctl_fw_download(MPT_ADAPTER *iocp, unsigned long arg)
 {
 	struct mpt_fw_xfer __user *ufwdl = (void __user *) arg;
 	struct mpt_fw_xfer	 kfwdl;
@@ -766,7 +759,7 @@ mptctl_fw_download(unsigned long arg)
 		return -EFAULT;
 	}
 
-	return mptctl_do_fw_download(kfwdl.iocnum, kfwdl.bufp, kfwdl.fwlen);
+	return mptctl_do_fw_download(iocp, kfwdl.bufp, kfwdl.fwlen);
 }
 
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
@@ -784,11 +777,10 @@ mptctl_fw_download(unsigned long arg)
  *		-ENOMSG if FW upload returned bad status
  */
 static int
-mptctl_do_fw_download(int ioc, char __user *ufwbuf, size_t fwlen)
+mptctl_do_fw_download(MPT_ADAPTER *iocp, char __user *ufwbuf, size_t fwlen)
 {
 	FWDownload_t		*dlmsg;
 	MPT_FRAME_HDR		*mf;
-	MPT_ADAPTER		*iocp;
 	FWDownloadTCSGE_t	*ptsge;
 	MptSge_t		*sgl, *sgIn;
 	char			*sgOut;
@@ -808,17 +800,10 @@ mptctl_do_fw_download(int ioc, char __user *ufwbuf, size_t fwlen)
 	pFWDownloadReply_t	 ReplyMsg = NULL;
 	unsigned long		 timeleft;
 
-	if (mpt_verify_adapter(ioc, &iocp) < 0) {
-		printk(KERN_DEBUG MYNAM "ioctl_fwdl - ioc%d not found!\n",
-				 ioc);
-		return -ENODEV; /* (-6) No such device or address */
-	} else {
-
-		/*  Valid device. Get a message frame and construct the FW download message.
-	 	*/
-		if ((mf = mpt_get_msg_frame(mptctl_id, iocp)) == NULL)
-			return -EAGAIN;
-	}
+	/*  Valid device. Get a message frame and construct the FW download message.
+	*/
+	if ((mf = mpt_get_msg_frame(mptctl_id, iocp)) == NULL)
+		return -EAGAIN;
 
 	dctlprintk(iocp, printk(MYIOC_s_DEBUG_FMT
 	    "mptctl_do_fwdl called. mptctl_id = %xh.\n", iocp->name, mptctl_id));
@@ -826,8 +811,6 @@ mptctl_do_fw_download(int ioc, char __user *ufwbuf, size_t fwlen)
 	    iocp->name, ufwbuf));
 	dctlprintk(iocp, printk(MYIOC_s_DEBUG_FMT "DbG: kfwdl.fwlen = %d\n",
 	    iocp->name, (int)fwlen));
-	dctlprintk(iocp, printk(MYIOC_s_DEBUG_FMT "DbG: kfwdl.ioc   = %04xh\n",
-	    iocp->name, ioc));
 
 	dlmsg = (FWDownload_t*) mf;
 	ptsge = (FWDownloadTCSGE_t *) &dlmsg->SGL;
@@ -1238,13 +1221,11 @@ kfree_sgl(MptSge_t *sgl, dma_addr_t sgl_dma, struct buflist *buflist, MPT_ADAPTE
  *		-ENODEV  if no such device/adapter
  */
 static int
-mptctl_getiocinfo (unsigned long arg, unsigned int data_size)
+mptctl_getiocinfo (MPT_ADAPTER *ioc, unsigned long arg, unsigned int data_size)
 {
 	struct mpt_ioctl_iocinfo __user *uarg = (void __user *) arg;
 	struct mpt_ioctl_iocinfo *karg;
-	MPT_ADAPTER		*ioc;
 	struct pci_dev		*pdev;
-	int			iocnum;
 	unsigned int		port;
 	int			cim_rev;
 	struct scsi_device 	*sdev;
@@ -1272,14 +1253,6 @@ mptctl_getiocinfo (unsigned long arg, unsigned int data_size)
 		return PTR_ERR(karg);
 	}
 
-	if (((iocnum = mpt_verify_adapter(karg->hdr.iocnum, &ioc)) < 0) ||
-	    (ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_getiocinfo() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		kfree(karg);
-		return -ENODEV;
-	}
-
 	/* Verify the data transfer size is correct. */
 	if (karg->hdr.maxDataSize != data_size) {
 		printk(MYIOC_s_ERR_FMT "%s@%d::mptctl_getiocinfo - "
@@ -1385,15 +1358,13 @@ mptctl_getiocinfo (unsigned long arg, unsigned int data_size)
  *		-ENODEV  if no such device/adapter
  */
 static int
-mptctl_gettargetinfo (unsigned long arg)
+mptctl_gettargetinfo (MPT_ADAPTER *ioc, unsigned long arg)
 {
 	struct mpt_ioctl_targetinfo __user *uarg = (void __user *) arg;
 	struct mpt_ioctl_targetinfo karg;
-	MPT_ADAPTER		*ioc;
 	VirtDevice		*vdevice;
 	char			*pmem;
 	int			*pdata;
-	int			iocnum;
 	int			numDevices = 0;
 	int			lun;
 	int			maxWordsLeft;
@@ -1408,13 +1379,6 @@ mptctl_gettargetinfo (unsigned long arg)
 		return -EFAULT;
 	}
 
-	if (((iocnum = mpt_verify_adapter(karg.hdr.iocnum, &ioc)) < 0) ||
-	    (ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_gettargetinfo() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		return -ENODEV;
-	}
-
 	dctlprintk(ioc, printk(MYIOC_s_DEBUG_FMT "mptctl_gettargetinfo called.\n",
 	    ioc->name));
 	/* Get the port number and set the maximum number of bytes
@@ -1510,12 +1474,10 @@ mptctl_gettargetinfo (unsigned long arg)
  *		-ENODEV  if no such device/adapter
  */
 static int
-mptctl_readtest (unsigned long arg)
+mptctl_readtest (MPT_ADAPTER *ioc, unsigned long arg)
 {
 	struct mpt_ioctl_test __user *uarg = (void __user *) arg;
 	struct mpt_ioctl_test	 karg;
-	MPT_ADAPTER *ioc;
-	int iocnum;
 
 	if (copy_from_user(&karg, uarg, sizeof(struct mpt_ioctl_test))) {
 		printk(KERN_ERR MYNAM "%s@%d::mptctl_readtest - "
@@ -1524,13 +1486,6 @@ mptctl_readtest (unsigned long arg)
 		return -EFAULT;
 	}
 
-	if (((iocnum = mpt_verify_adapter(karg.hdr.iocnum, &ioc)) < 0) ||
-	    (ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_readtest() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		return -ENODEV;
-	}
-
 	dctlprintk(ioc, printk(MYIOC_s_DEBUG_FMT "mptctl_readtest called.\n",
 	    ioc->name));
 	/* Fill in the data and return the structure to the calling
@@ -1571,12 +1526,10 @@ mptctl_readtest (unsigned long arg)
  *		-ENODEV  if no such device/adapter
  */
 static int
-mptctl_eventquery (unsigned long arg)
+mptctl_eventquery (MPT_ADAPTER *ioc, unsigned long arg)
 {
 	struct mpt_ioctl_eventquery __user *uarg = (void __user *) arg;
 	struct mpt_ioctl_eventquery	 karg;
-	MPT_ADAPTER *ioc;
-	int iocnum;
 
 	if (copy_from_user(&karg, uarg, sizeof(struct mpt_ioctl_eventquery))) {
 		printk(KERN_ERR MYNAM "%s@%d::mptctl_eventquery - "
@@ -1585,13 +1538,6 @@ mptctl_eventquery (unsigned long arg)
 		return -EFAULT;
 	}
 
-	if (((iocnum = mpt_verify_adapter(karg.hdr.iocnum, &ioc)) < 0) ||
-	    (ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_eventquery() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		return -ENODEV;
-	}
-
 	dctlprintk(ioc, printk(MYIOC_s_DEBUG_FMT "mptctl_eventquery called.\n",
 	    ioc->name));
 	karg.eventEntries = MPTCTL_EVENT_LOG_SIZE;
@@ -1610,12 +1556,10 @@ mptctl_eventquery (unsigned long arg)
 
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
 static int
-mptctl_eventenable (unsigned long arg)
+mptctl_eventenable (MPT_ADAPTER *ioc, unsigned long arg)
 {
 	struct mpt_ioctl_eventenable __user *uarg = (void __user *) arg;
 	struct mpt_ioctl_eventenable	 karg;
-	MPT_ADAPTER *ioc;
-	int iocnum;
 
 	if (copy_from_user(&karg, uarg, sizeof(struct mpt_ioctl_eventenable))) {
 		printk(KERN_ERR MYNAM "%s@%d::mptctl_eventenable - "
@@ -1624,13 +1568,6 @@ mptctl_eventenable (unsigned long arg)
 		return -EFAULT;
 	}
 
-	if (((iocnum = mpt_verify_adapter(karg.hdr.iocnum, &ioc)) < 0) ||
-	    (ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_eventenable() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		return -ENODEV;
-	}
-
 	dctlprintk(ioc, printk(MYIOC_s_DEBUG_FMT "mptctl_eventenable called.\n",
 	    ioc->name));
 	if (ioc->events == NULL) {
@@ -1658,12 +1595,10 @@ mptctl_eventenable (unsigned long arg)
 
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
 static int
-mptctl_eventreport (unsigned long arg)
+mptctl_eventreport (MPT_ADAPTER *ioc, unsigned long arg)
 {
 	struct mpt_ioctl_eventreport __user *uarg = (void __user *) arg;
 	struct mpt_ioctl_eventreport	 karg;
-	MPT_ADAPTER		 *ioc;
-	int			 iocnum;
 	int			 numBytes, maxEvents, max;
 
 	if (copy_from_user(&karg, uarg, sizeof(struct mpt_ioctl_eventreport))) {
@@ -1673,12 +1608,6 @@ mptctl_eventreport (unsigned long arg)
 		return -EFAULT;
 	}
 
-	if (((iocnum = mpt_verify_adapter(karg.hdr.iocnum, &ioc)) < 0) ||
-	    (ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_eventreport() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		return -ENODEV;
-	}
 	dctlprintk(ioc, printk(MYIOC_s_DEBUG_FMT "mptctl_eventreport called.\n",
 	    ioc->name));
 
@@ -1712,12 +1641,10 @@ mptctl_eventreport (unsigned long arg)
 
 /*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
 static int
-mptctl_replace_fw (unsigned long arg)
+mptctl_replace_fw (MPT_ADAPTER *ioc, unsigned long arg)
 {
 	struct mpt_ioctl_replace_fw __user *uarg = (void __user *) arg;
 	struct mpt_ioctl_replace_fw	 karg;
-	MPT_ADAPTER		 *ioc;
-	int			 iocnum;
 	int			 newFwSize;
 
 	if (copy_from_user(&karg, uarg, sizeof(struct mpt_ioctl_replace_fw))) {
@@ -1727,13 +1654,6 @@ mptctl_replace_fw (unsigned long arg)
 		return -EFAULT;
 	}
 
-	if (((iocnum = mpt_verify_adapter(karg.hdr.iocnum, &ioc)) < 0) ||
-	    (ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_replace_fw() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		return -ENODEV;
-	}
-
 	dctlprintk(ioc, printk(MYIOC_s_DEBUG_FMT "mptctl_replace_fw called.\n",
 	    ioc->name));
 	/* If caching FW, Free the old FW image
@@ -1780,12 +1700,10 @@ mptctl_replace_fw (unsigned long arg)
  *		-ENOMEM if memory allocation error
  */
 static int
-mptctl_mpt_command (unsigned long arg)
+mptctl_mpt_command (MPT_ADAPTER *ioc, unsigned long arg)
 {
 	struct mpt_ioctl_command __user *uarg = (void __user *) arg;
 	struct mpt_ioctl_command  karg;
-	MPT_ADAPTER	*ioc;
-	int		iocnum;
 	int		rc;
 
 
@@ -1796,14 +1714,7 @@ mptctl_mpt_command (unsigned long arg)
 		return -EFAULT;
 	}
 
-	if (((iocnum = mpt_verify_adapter(karg.hdr.iocnum, &ioc)) < 0) ||
-	    (ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_mpt_command() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		return -ENODEV;
-	}
-
-	rc = mptctl_do_mpt_command (karg, &uarg->MF);
+	rc = mptctl_do_mpt_command (ioc, karg, &uarg->MF);
 
 	return rc;
 }
@@ -1821,9 +1732,8 @@ mptctl_mpt_command (unsigned long arg)
  *		-EPERM if SCSI I/O and target is untagged
  */
 static int
-mptctl_do_mpt_command (struct mpt_ioctl_command karg, void __user *mfPtr)
+mptctl_do_mpt_command (MPT_ADAPTER *ioc, struct mpt_ioctl_command karg, void __user *mfPtr)
 {
-	MPT_ADAPTER	*ioc;
 	MPT_FRAME_HDR	*mf = NULL;
 	MPIHeader_t	*hdr;
 	char		*psge;
@@ -1832,7 +1742,7 @@ mptctl_do_mpt_command (struct mpt_ioctl_command karg, void __user *mfPtr)
 	dma_addr_t	dma_addr_in;
 	dma_addr_t	dma_addr_out;
 	int		sgSize = 0;	/* Num SG elements */
-	int		iocnum, flagsLength;
+	int		flagsLength;
 	int		sz, rc = 0;
 	int		msgContext;
 	u16		req_idx;
@@ -1847,13 +1757,6 @@ mptctl_do_mpt_command (struct mpt_ioctl_command karg, void __user *mfPtr)
 	bufIn.kptr = bufOut.kptr = NULL;
 	bufIn.len = bufOut.len = 0;
 
-	if (((iocnum = mpt_verify_adapter(karg.hdr.iocnum, &ioc)) < 0) ||
-	    (ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_do_mpt_command() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		return -ENODEV;
-	}
-
 	spin_lock_irqsave(&ioc->taskmgmt_lock, flags);
 	if (ioc->ioc_reset_in_progress) {
 		spin_unlock_irqrestore(&ioc->taskmgmt_lock, flags);
@@ -2418,17 +2321,15 @@ done_free_mem:
  *		-ENOMEM if memory allocation error
  */
 static int
-mptctl_hp_hostinfo(unsigned long arg, unsigned int data_size)
+mptctl_hp_hostinfo(MPT_ADAPTER *ioc, unsigned long arg, unsigned int data_size)
 {
 	hp_host_info_t	__user *uarg = (void __user *) arg;
-	MPT_ADAPTER		*ioc;
 	struct pci_dev		*pdev;
 	char                    *pbuf=NULL;
 	dma_addr_t		buf_dma;
 	hp_host_info_t		karg;
 	CONFIGPARMS		cfg;
 	ConfigPageHeader_t	hdr;
-	int			iocnum;
 	int			rc, cim_rev;
 	ToolboxIstwiReadWriteRequest_t	*IstwiRWRequest;
 	MPT_FRAME_HDR		*mf = NULL;
@@ -2452,12 +2353,6 @@ mptctl_hp_hostinfo(unsigned long arg, unsigned int data_size)
 		return -EFAULT;
 	}
 
-	if (((iocnum = mpt_verify_adapter(karg.hdr.iocnum, &ioc)) < 0) ||
-	    (ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_hp_hostinfo() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		return -ENODEV;
-	}
 	dctlprintk(ioc, printk(MYIOC_s_DEBUG_FMT ": mptctl_hp_hostinfo called.\n",
 	    ioc->name));
 
@@ -2659,15 +2554,13 @@ retry_wait:
  *		-ENOMEM if memory allocation error
  */
 static int
-mptctl_hp_targetinfo(unsigned long arg)
+mptctl_hp_targetinfo(MPT_ADAPTER *ioc, unsigned long arg)
 {
 	hp_target_info_t __user *uarg = (void __user *) arg;
 	SCSIDevicePage0_t	*pg0_alloc;
 	SCSIDevicePage3_t	*pg3_alloc;
-	MPT_ADAPTER		*ioc;
 	MPT_SCSI_HOST 		*hd = NULL;
 	hp_target_info_t	karg;
-	int			iocnum;
 	int			data_sz;
 	dma_addr_t		page_dma;
 	CONFIGPARMS	 	cfg;
@@ -2681,12 +2574,6 @@ mptctl_hp_targetinfo(unsigned long arg)
 		return -EFAULT;
 	}
 
-	if (((iocnum = mpt_verify_adapter(karg.hdr.iocnum, &ioc)) < 0) ||
-		(ioc == NULL)) {
-		printk(KERN_DEBUG MYNAM "%s::mptctl_hp_targetinfo() @%d - ioc%d not found!\n",
-				__FILE__, __LINE__, iocnum);
-		return -ENODEV;
-	}
 	if (karg.hdr.id >= MPT_MAX_FC_DEVICES)
 		return -EINVAL;
 	dctlprintk(ioc, printk(MYIOC_s_DEBUG_FMT "mptctl_hp_targetinfo called.\n",
@@ -2854,7 +2741,7 @@ compat_mptfwxfer_ioctl(struct file *filp, unsigned int cmd,
 	kfw.fwlen = kfw32.fwlen;
 	kfw.bufp = compat_ptr(kfw32.bufp);
 
-	ret = mptctl_do_fw_download(kfw.iocnum, kfw.bufp, kfw.fwlen);
+	ret = mptctl_do_fw_download(iocp, kfw.bufp, kfw.fwlen);
 
 	mutex_unlock(&iocp->ioctl_cmds.mutex);
 
@@ -2908,7 +2795,7 @@ compat_mpt_command(struct file *filp, unsigned int cmd,
 
 	/* Pass new structure to do_mpt_command
 	 */
-	ret = mptctl_do_mpt_command (karg, &uarg->MF);
+	ret = mptctl_do_mpt_command (iocp, karg, &uarg->MF);
 
 	mutex_unlock(&iocp->ioctl_cmds.mutex);
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 088/107] net: hns3: pad the short frame before sending to the hardware

[Sasha Levin]

From: Yunsheng Lin <linyunsheng@huawei.com>

[ Upstream commit 36c67349a1a1c88b9cf11d7ca7762ababdb38867 ]

The hardware can not handle short frames below or equal to 32
bytes according to the hardware user manual, and it will trigger
a RAS error when the frame's length is below 33 bytes.

This patch pads the SKB when skb->len is below 33 bytes before
sending it to hardware.

Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/hisilicon/hns3/hns3_enet.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c b/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c
index 84d8816c8681b..0c8d2269bc46e 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c
@@ -54,6 +54,8 @@ MODULE_PARM_DESC(debug, " Network interface message level setting");
 #define HNS3_INNER_VLAN_TAG	1
 #define HNS3_OUTER_VLAN_TAG	2
 
+#define HNS3_MIN_TX_LEN		33U
+
 /* hns3_pci_tbl - PCI Device ID Table
  *
  * Last entry must be all 0s
@@ -1329,6 +1331,10 @@ netdev_tx_t hns3_nic_net_xmit(struct sk_buff *skb, struct net_device *netdev)
 	int ret;
 	int i;
 
+	/* Hardware can only handle short frames above 32 bytes */
+	if (skb_put_padto(skb, HNS3_MIN_TX_LEN))
+		return NETDEV_TX_OK;
+
 	/* Prefetch the data used later */
 	prefetch(skb->data);
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 089/107] net: ethernet: ave: Avoid lockdep warning

[Sasha Levin]

From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>

[ Upstream commit 82d5d6a638cbd12b7dfe8acafd9efd87a656cc06 ]

When building with PROVE_LOCKING=y, lockdep shows the following
dump message.

    INFO: trying to register non-static key.
    the code is fine but needs lockdep annotation.
    turning off the locking correctness validator.
     ...

Calling device_set_wakeup_enable() directly occurs this issue,
and it isn't necessary for initialization, so this patch creates
internal function __ave_ethtool_set_wol() and replaces with this
in ave_init() and ave_resume().

Fixes: 7200f2e3c9e2 ("net: ethernet: ave: Set initial wol state to disabled")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/socionext/sni_ave.c | 20 +++++++++++++-------
 1 file changed, 13 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/socionext/sni_ave.c b/drivers/net/ethernet/socionext/sni_ave.c
index 6e984d5a729fe..38d39c4b5ac83 100644
--- a/drivers/net/ethernet/socionext/sni_ave.c
+++ b/drivers/net/ethernet/socionext/sni_ave.c
@@ -424,16 +424,22 @@ static void ave_ethtool_get_wol(struct net_device *ndev,
 		phy_ethtool_get_wol(ndev->phydev, wol);
 }
 
-static int ave_ethtool_set_wol(struct net_device *ndev,
-			       struct ethtool_wolinfo *wol)
+static int __ave_ethtool_set_wol(struct net_device *ndev,
+				 struct ethtool_wolinfo *wol)
 {
-	int ret;
-
 	if (!ndev->phydev ||
 	    (wol->wolopts & (WAKE_ARP | WAKE_MAGICSECURE)))
 		return -EOPNOTSUPP;
 
-	ret = phy_ethtool_set_wol(ndev->phydev, wol);
+	return phy_ethtool_set_wol(ndev->phydev, wol);
+}
+
+static int ave_ethtool_set_wol(struct net_device *ndev,
+			       struct ethtool_wolinfo *wol)
+{
+	int ret;
+
+	ret = __ave_ethtool_set_wol(ndev, wol);
 	if (!ret)
 		device_set_wakeup_enable(&ndev->dev, !!wol->wolopts);
 
@@ -1216,7 +1222,7 @@ static int ave_init(struct net_device *ndev)
 
 	/* set wol initial state disabled */
 	wol.wolopts = 0;
-	ave_ethtool_set_wol(ndev, &wol);
+	__ave_ethtool_set_wol(ndev, &wol);
 
 	if (!phy_interface_is_rgmii(phydev))
 		phy_set_max_speed(phydev, SPEED_100);
@@ -1768,7 +1774,7 @@ static int ave_resume(struct device *dev)
 
 	ave_ethtool_get_wol(ndev, &wol);
 	wol.wolopts = priv->wolopts;
-	ave_ethtool_set_wol(ndev, &wol);
+	__ave_ethtool_set_wol(ndev, &wol);
 
 	if (ndev->phydev) {
 		ret = phy_resume(ndev->phydev);
-- 
2.20.1

[PATCH AUTOSEL 5.4 090/107] netfilter: nf_tables: store transaction list locally while requesting module

[Sasha Levin]

From: Pablo Neira Ayuso <pablo@netfilter.org>

[ Upstream commit ec7470b834fe7b5d7eff11b6677f5d7fdf5e9a91 ]

This patch fixes a WARN_ON in nft_set_destroy() due to missing
set reference count drop from the preparation phase. This is triggered
by the module autoload path. Do not exercise the abort path from
nft_request_module() while preparation phase cleaning up is still
pending.

 WARNING: CPU: 3 PID: 3456 at net/netfilter/nf_tables_api.c:3740 nft_set_destroy+0x45/0x50 [nf_tables]
 [...]
 CPU: 3 PID: 3456 Comm: nft Not tainted 5.4.6-arch3-1 #1
 RIP: 0010:nft_set_destroy+0x45/0x50 [nf_tables]
 Code: e8 30 eb 83 c6 48 8b 85 80 00 00 00 48 8b b8 90 00 00 00 e8 dd 6b d7 c5 48 8b 7d 30 e8 24 dd eb c5 48 89 ef 5d e9 6b c6 e5 c5 <0f> 0b c3 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 8b 7f 10 e9 52
 RSP: 0018:ffffac4f43e53700 EFLAGS: 00010202
 RAX: 0000000000000001 RBX: ffff99d63a154d80 RCX: 0000000001f88e03
 RDX: 0000000001f88c03 RSI: ffff99d6560ef0c0 RDI: ffff99d63a101200
 RBP: ffff99d617721de0 R08: 0000000000000000 R09: 0000000000000318
 R10: 00000000f0000000 R11: 0000000000000001 R12: ffffffff880fabf0
 R13: dead000000000122 R14: dead000000000100 R15: ffff99d63a154d80
 FS:  00007ff3dbd5b740(0000) GS:ffff99d6560c0000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00001cb5de6a9000 CR3: 000000016eb6a004 CR4: 00000000001606e0
 Call Trace:
  __nf_tables_abort+0x3e3/0x6d0 [nf_tables]
  nft_request_module+0x6f/0x110 [nf_tables]
  nft_expr_type_request_module+0x28/0x50 [nf_tables]
  nf_tables_expr_parse+0x198/0x1f0 [nf_tables]
  nft_expr_init+0x3b/0xf0 [nf_tables]
  nft_dynset_init+0x1e2/0x410 [nf_tables]
  nf_tables_newrule+0x30a/0x930 [nf_tables]
  nfnetlink_rcv_batch+0x2a0/0x640 [nfnetlink]
  nfnetlink_rcv+0x125/0x171 [nfnetlink]
  netlink_unicast+0x179/0x210
  netlink_sendmsg+0x208/0x3d0
  sock_sendmsg+0x5e/0x60
  ____sys_sendmsg+0x21b/0x290

Update comment on the code to describe the new behaviour.

Reported-by: Marco Oliverio <marco.oliverio@tanaza.com>
Fixes: 452238e8d5ff ("netfilter: nf_tables: add and use helper for module autoload")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/nf_tables_api.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

diff --git a/net/netfilter/nf_tables_api.c b/net/netfilter/nf_tables_api.c
index 67ca47c7ce542..b0cd1cee412b2 100644
--- a/net/netfilter/nf_tables_api.c
+++ b/net/netfilter/nf_tables_api.c
@@ -500,23 +500,21 @@ __nf_tables_chain_type_lookup(const struct nlattr *nla, u8 family)
 }
 
 /*
- * Loading a module requires dropping mutex that guards the
- * transaction.
- * We first need to abort any pending transactions as once
- * mutex is unlocked a different client could start a new
- * transaction.  It must not see any 'future generation'
- * changes * as these changes will never happen.
+ * Loading a module requires dropping mutex that guards the transaction.
+ * A different client might race to start a new transaction meanwhile. Zap the
+ * list of pending transaction and then restore it once the mutex is grabbed
+ * again. Users of this function return EAGAIN which implicitly triggers the
+ * transaction abort path to clean up the list of pending transactions.
  */
 #ifdef CONFIG_MODULES
-static int __nf_tables_abort(struct net *net);
-
 static void nft_request_module(struct net *net, const char *fmt, ...)
 {
 	char module_name[MODULE_NAME_LEN];
+	LIST_HEAD(commit_list);
 	va_list args;
 	int ret;
 
-	__nf_tables_abort(net);
+	list_splice_init(&net->nft.commit_list, &commit_list);
 
 	va_start(args, fmt);
 	ret = vsnprintf(module_name, MODULE_NAME_LEN, fmt, args);
@@ -527,6 +525,9 @@ static void nft_request_module(struct net *net, const char *fmt, ...)
 	mutex_unlock(&net->nft.commit_mutex);
 	request_module("%s", module_name);
 	mutex_lock(&net->nft.commit_mutex);
+
+	WARN_ON_ONCE(!list_empty(&net->nft.commit_list));
+	list_splice(&commit_list, &net->nft.commit_list);
 }
 #endif
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 091/107] netfilter: nft_tunnel: fix null-attribute check

[Sasha Levin]

From: Florian Westphal <fw@strlen.de>

[ Upstream commit 1c702bf902bd37349f6d91cd7f4b372b1e46d0ed ]

else we get null deref when one of the attributes is missing, both
must be non-null.

Reported-by: syzbot+76d0b80493ac881ff77b@syzkaller.appspotmail.com
Fixes: aaecfdb5c5dd8ba ("netfilter: nf_tables: match on tunnel metadata")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/nft_tunnel.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/netfilter/nft_tunnel.c b/net/netfilter/nft_tunnel.c
index 3d4c2ae605a8e..d89c7c5530309 100644
--- a/net/netfilter/nft_tunnel.c
+++ b/net/netfilter/nft_tunnel.c
@@ -76,7 +76,7 @@ static int nft_tunnel_get_init(const struct nft_ctx *ctx,
 	struct nft_tunnel *priv = nft_expr_priv(expr);
 	u32 len;
 
-	if (!tb[NFTA_TUNNEL_KEY] &&
+	if (!tb[NFTA_TUNNEL_KEY] ||
 	    !tb[NFTA_TUNNEL_DREG])
 		return -EINVAL;
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 092/107] netfilter: nft_tunnel: ERSPAN_VERSION must not be null

[Sasha Levin]

From: Florian Westphal <fw@strlen.de>

[ Upstream commit 9ec22d7c6c69146180577f3ad5fdf504beeaee62 ]

Fixes: af308b94a2a4a5 ("netfilter: nf_tables: add tunnel support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/nft_tunnel.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/net/netfilter/nft_tunnel.c b/net/netfilter/nft_tunnel.c
index d89c7c5530309..5284fcf16be73 100644
--- a/net/netfilter/nft_tunnel.c
+++ b/net/netfilter/nft_tunnel.c
@@ -266,6 +266,9 @@ static int nft_tunnel_obj_erspan_init(const struct nlattr *attr,
 	if (err < 0)
 		return err;
 
+	if (!tb[NFTA_TUNNEL_KEY_ERSPAN_VERSION])
+		 return -EINVAL;
+
 	version = ntohl(nla_get_be32(tb[NFTA_TUNNEL_KEY_ERSPAN_VERSION]));
 	switch (version) {
 	case ERSPAN_VERSION:
-- 
2.20.1

[PATCH AUTOSEL 5.4 093/107] netfilter: nf_tables: remove WARN and add NLA_STRING upper limits

[Sasha Levin]

From: Florian Westphal <fw@strlen.de>

[ Upstream commit 9332d27d7918182add34e8043f6a754530fdd022 ]

This WARN can trigger because some of the names fed to the module
autoload function can be of arbitrary length.

Remove the WARN and add limits for all NLA_STRING attributes.

Reported-by: syzbot+0e63ae76d117ae1c3a01@syzkaller.appspotmail.com
Fixes: 452238e8d5ffd8 ("netfilter: nf_tables: add and use helper for module autoload")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/nf_tables_api.c | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)

diff --git a/net/netfilter/nf_tables_api.c b/net/netfilter/nf_tables_api.c
index b0cd1cee412b2..6fa315b73a66a 100644
--- a/net/netfilter/nf_tables_api.c
+++ b/net/netfilter/nf_tables_api.c
@@ -22,6 +22,8 @@
 #include <net/net_namespace.h>
 #include <net/sock.h>
 
+#define NFT_MODULE_AUTOLOAD_LIMIT (MODULE_NAME_LEN - sizeof("nft-expr-255-"))
+
 static LIST_HEAD(nf_tables_expressions);
 static LIST_HEAD(nf_tables_objects);
 static LIST_HEAD(nf_tables_flowtables);
@@ -519,7 +521,7 @@ static void nft_request_module(struct net *net, const char *fmt, ...)
 	va_start(args, fmt);
 	ret = vsnprintf(module_name, MODULE_NAME_LEN, fmt, args);
 	va_end(args);
-	if (WARN(ret >= MODULE_NAME_LEN, "truncated: '%s' (len %d)", module_name, ret))
+	if (ret >= MODULE_NAME_LEN)
 		return;
 
 	mutex_unlock(&net->nft.commit_mutex);
@@ -1175,7 +1177,8 @@ static const struct nla_policy nft_chain_policy[NFTA_CHAIN_MAX + 1] = {
 				    .len = NFT_CHAIN_MAXNAMELEN - 1 },
 	[NFTA_CHAIN_HOOK]	= { .type = NLA_NESTED },
 	[NFTA_CHAIN_POLICY]	= { .type = NLA_U32 },
-	[NFTA_CHAIN_TYPE]	= { .type = NLA_STRING },
+	[NFTA_CHAIN_TYPE]	= { .type = NLA_STRING,
+				    .len = NFT_MODULE_AUTOLOAD_LIMIT },
 	[NFTA_CHAIN_COUNTERS]	= { .type = NLA_NESTED },
 	[NFTA_CHAIN_FLAGS]	= { .type = NLA_U32 },
 };
@@ -2089,7 +2092,8 @@ static const struct nft_expr_type *nft_expr_type_get(struct net *net,
 }
 
 static const struct nla_policy nft_expr_policy[NFTA_EXPR_MAX + 1] = {
-	[NFTA_EXPR_NAME]	= { .type = NLA_STRING },
+	[NFTA_EXPR_NAME]	= { .type = NLA_STRING,
+				    .len = NFT_MODULE_AUTOLOAD_LIMIT },
 	[NFTA_EXPR_DATA]	= { .type = NLA_NESTED },
 };
 
@@ -3932,7 +3936,8 @@ static const struct nla_policy nft_set_elem_policy[NFTA_SET_ELEM_MAX + 1] = {
 	[NFTA_SET_ELEM_USERDATA]	= { .type = NLA_BINARY,
 					    .len = NFT_USERDATA_MAXLEN },
 	[NFTA_SET_ELEM_EXPR]		= { .type = NLA_NESTED },
-	[NFTA_SET_ELEM_OBJREF]		= { .type = NLA_STRING },
+	[NFTA_SET_ELEM_OBJREF]		= { .type = NLA_STRING,
+					    .len = NFT_OBJ_MAXNAMELEN - 1 },
 };
 
 static const struct nla_policy nft_set_elem_list_policy[NFTA_SET_ELEM_LIST_MAX + 1] = {
-- 
2.20.1

[PATCH AUTOSEL 5.4 094/107] netfilter: nf_tables: fix flowtable list del corruption

[Sasha Levin]

From: Florian Westphal <fw@strlen.de>

[ Upstream commit 335178d5429c4cee61b58f4ac80688f556630818 ]

syzbot reported following crash:

  list_del corruption, ffff88808c9bb000->prev is LIST_POISON2 (dead000000000122)
  [..]
  Call Trace:
   __list_del_entry include/linux/list.h:131 [inline]
   list_del_rcu include/linux/rculist.h:148 [inline]
   nf_tables_commit+0x1068/0x3b30 net/netfilter/nf_tables_api.c:7183
   [..]

The commit transaction list has:

NFT_MSG_NEWTABLE
NFT_MSG_NEWFLOWTABLE
NFT_MSG_DELFLOWTABLE
NFT_MSG_DELTABLE

A missing generation check during DELTABLE processing causes it to queue
the DELFLOWTABLE operation a second time, so we corrupt the list here:

  case NFT_MSG_DELFLOWTABLE:
     list_del_rcu(&nft_trans_flowtable(trans)->list);
     nf_tables_flowtable_notify(&trans->ctx,

because we have two different DELFLOWTABLE transactions for the same
flowtable.  We then call list_del_rcu() twice for the same flowtable->list.

The object handling seems to suffer from the same bug so add a generation
check too and only queue delete transactions for flowtables/objects that
are still active in the next generation.

Reported-by: syzbot+37a6804945a3a13b1572@syzkaller.appspotmail.com
Fixes: 3b49e2e94e6eb ("netfilter: nf_tables: add flow table netlink frontend")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/nf_tables_api.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/net/netfilter/nf_tables_api.c b/net/netfilter/nf_tables_api.c
index 6fa315b73a66a..9fefd01500918 100644
--- a/net/netfilter/nf_tables_api.c
+++ b/net/netfilter/nf_tables_api.c
@@ -981,12 +981,18 @@ static int nft_flush_table(struct nft_ctx *ctx)
 	}
 
 	list_for_each_entry_safe(flowtable, nft, &ctx->table->flowtables, list) {
+		if (!nft_is_active_next(ctx->net, flowtable))
+			continue;
+
 		err = nft_delflowtable(ctx, flowtable);
 		if (err < 0)
 			goto out;
 	}
 
 	list_for_each_entry_safe(obj, ne, &ctx->table->objects, list) {
+		if (!nft_is_active_next(ctx->net, obj))
+			continue;
+
 		err = nft_delobj(ctx, obj);
 		if (err < 0)
 			goto out;
-- 
2.20.1

[PATCH AUTOSEL 5.4 095/107] netfilter: nat: fix ICMP header corruption on ICMP errors

[Sasha Levin]

From: Eyal Birger <eyal.birger@gmail.com>

[ Upstream commit 61177e911dad660df86a4553eb01c95ece2f6a82 ]

Commit 8303b7e8f018 ("netfilter: nat: fix spurious connection timeouts")
made nf_nat_icmp_reply_translation() use icmp_manip_pkt() as the l4
manipulation function for the outer packet on ICMP errors.

However, icmp_manip_pkt() assumes the packet has an 'id' field which
is not correct for all types of ICMP messages.

This is not correct for ICMP error packets, and leads to bogus bytes
being written the ICMP header, which can be wrongfully regarded as
'length' bytes by RFC 4884 compliant receivers.

Fix by assigning the 'id' field only for ICMP messages that have this
semantic.

Reported-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Fixes: 8303b7e8f018 ("netfilter: nat: fix spurious connection timeouts")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/nf_nat_proto.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/net/netfilter/nf_nat_proto.c b/net/netfilter/nf_nat_proto.c
index 0a59c14b51776..64eedc17037ad 100644
--- a/net/netfilter/nf_nat_proto.c
+++ b/net/netfilter/nf_nat_proto.c
@@ -233,6 +233,19 @@ icmp_manip_pkt(struct sk_buff *skb,
 		return false;
 
 	hdr = (struct icmphdr *)(skb->data + hdroff);
+	switch (hdr->type) {
+	case ICMP_ECHO:
+	case ICMP_ECHOREPLY:
+	case ICMP_TIMESTAMP:
+	case ICMP_TIMESTAMPREPLY:
+	case ICMP_INFO_REQUEST:
+	case ICMP_INFO_REPLY:
+	case ICMP_ADDRESS:
+	case ICMP_ADDRESSREPLY:
+		break;
+	default:
+		return true;
+	}
 	inet_proto_csum_replace2(&hdr->checksum, skb,
 				 hdr->un.echo.id, tuple->src.u.icmp.id, false);
 	hdr->un.echo.id = tuple->src.u.icmp.id;
-- 
2.20.1

[PATCH AUTOSEL 5.4 096/107] net: hns: fix soft lockup when there is not enough memory

[Sasha Levin]

From: Yonglong Liu <liuyonglong@huawei.com>

[ Upstream commit 49edd6a2c456150870ddcef5b7ed11b21d849e13 ]

When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.

When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.

Fixes: 36eedfde1a36 ("net: hns: Optimize hns_nic_common_poll for better performance")
Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/hisilicon/hns/hns_enet.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/hisilicon/hns/hns_enet.c b/drivers/net/ethernet/hisilicon/hns/hns_enet.c
index 14ab20491fd02..eb69e5c81a4d0 100644
--- a/drivers/net/ethernet/hisilicon/hns/hns_enet.c
+++ b/drivers/net/ethernet/hisilicon/hns/hns_enet.c
@@ -565,7 +565,6 @@ static int hns_nic_poll_rx_skb(struct hns_nic_ring_data *ring_data,
 	skb = *out_skb = napi_alloc_skb(&ring_data->napi,
 					HNS_RX_HEAD_SIZE);
 	if (unlikely(!skb)) {
-		netdev_err(ndev, "alloc rx skb fail\n");
 		ring->stats.sw_err_cnt++;
 		return -ENOMEM;
 	}
@@ -1056,7 +1055,6 @@ static int hns_nic_common_poll(struct napi_struct *napi, int budget)
 		container_of(napi, struct hns_nic_ring_data, napi);
 	struct hnae_ring *ring = ring_data->ring;
 
-try_again:
 	clean_complete += ring_data->poll_one(
 				ring_data, budget - clean_complete,
 				ring_data->ex_process);
@@ -1066,7 +1064,7 @@ try_again:
 			napi_complete(napi);
 			ring->q->handle->dev->ops->toggle_ring_irq(ring, 0);
 		} else {
-			goto try_again;
+			return budget;
 		}
 	}
 
-- 
2.20.1