* [PATCH net-next v2 0/3] net: phy: Better support for BCM54810
@ 2020-02-19 20:00 Florian Fainelli
2020-02-19 20:00 ` [PATCH net-next v2 1/3] net: phy: broadcom: Allow BCM54810 to use bcm54xx_adjust_rxrefclk() Florian Fainelli
` (3 more replies)
0 siblings, 4 replies; 6+ messages in thread
From: Florian Fainelli @ 2020-02-19 20:00 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, Heiner Kallweit, Russell King,
David S. Miller, open list
Hi David, Andrew, Heiner,
This patch series updates the broadcom PHY driver to better support the
BCM54810 and allow it to make use of the exiting
bcm54xx_adjust_rxrefclk() as well as fix suspend/resume for it.
Changes in v2:
- added Reviewed-by tags from Andrew for patches #1 and #3
- expanded commit message in #2 to explain the change
Florian Fainelli (3):
net: phy: broadcom: Allow BCM54810 to use bcm54xx_adjust_rxrefclk()
net: phy: broadcom: Have bcm54xx_adjust_rxrefclk() check for flags
net: phy: broadcom: Wire suspend/resume for BCM54810
drivers/net/phy/broadcom.c | 24 +++++++++++++++++++-----
1 file changed, 19 insertions(+), 5 deletions(-)
--
2.17.1
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH net-next v2 1/3] net: phy: broadcom: Allow BCM54810 to use bcm54xx_adjust_rxrefclk()
2020-02-19 20:00 [PATCH net-next v2 0/3] net: phy: Better support for BCM54810 Florian Fainelli
@ 2020-02-19 20:00 ` Florian Fainelli
2020-02-19 20:00 ` [PATCH net-next v2 2/3] net: phy: broadcom: Have bcm54xx_adjust_rxrefclk() check for flags Florian Fainelli
` (2 subsequent siblings)
3 siblings, 0 replies; 6+ messages in thread
From: Florian Fainelli @ 2020-02-19 20:00 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, Heiner Kallweit, Russell King,
David S. Miller, open list
The function bcm54xx_adjust_rxrefclk() works correctly on the BCM54810
PHY, allow this device ID to proceed through.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/phy/broadcom.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 7d68b28bb893..4ad2128cc454 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -194,7 +194,8 @@ static void bcm54xx_adjust_rxrefclk(struct phy_device *phydev)
/* Abort if we are using an untested phy. */
if (BRCM_PHY_MODEL(phydev) != PHY_ID_BCM57780 &&
BRCM_PHY_MODEL(phydev) != PHY_ID_BCM50610 &&
- BRCM_PHY_MODEL(phydev) != PHY_ID_BCM50610M)
+ BRCM_PHY_MODEL(phydev) != PHY_ID_BCM50610M &&
+ BRCM_PHY_MODEL(phydev) != PHY_ID_BCM54810)
return;
val = bcm_phy_read_shadow(phydev, BCM54XX_SHD_SCR3);
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH net-next v2 2/3] net: phy: broadcom: Have bcm54xx_adjust_rxrefclk() check for flags
2020-02-19 20:00 [PATCH net-next v2 0/3] net: phy: Better support for BCM54810 Florian Fainelli
2020-02-19 20:00 ` [PATCH net-next v2 1/3] net: phy: broadcom: Allow BCM54810 to use bcm54xx_adjust_rxrefclk() Florian Fainelli
@ 2020-02-19 20:00 ` Florian Fainelli
2020-02-19 20:20 ` Andrew Lunn
2020-02-19 20:00 ` [PATCH net-next v2 3/3] net: phy: broadcom: Wire suspend/resume for BCM54810 Florian Fainelli
2020-02-20 0:37 ` [PATCH net-next v2 0/3] net: phy: Better support " David Miller
3 siblings, 1 reply; 6+ messages in thread
From: Florian Fainelli @ 2020-02-19 20:00 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, Heiner Kallweit, Russell King,
David S. Miller, open list
bcm54xx_adjust_rxrefclk() already checks for PHY_BRCM_AUTO_PWRDWN_ENABLE
and PHY_BRCM_DIS_TXCRXC_NOENRGY in order to set the appropriate bit. The
situation is a bit more complicated with the flag
PHY_BRCM_RX_REFCLK_UNUSED but essentially amounts to the same situation.
The default setting for the 125MHz clock is to be on for all PHYs and
we still treat BCM50610 and BCM50610M specifically with the polarity of
the bit reversed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/phy/broadcom.c | 5 +----
1 file changed, 1 insertion(+), 4 deletions(-)
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 4ad2128cc454..b4eae84a9195 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -273,10 +273,7 @@ static int bcm54xx_config_init(struct phy_device *phydev)
(phydev->dev_flags & PHY_BRCM_CLEAR_RGMII_MODE))
bcm_phy_write_shadow(phydev, BCM54XX_SHD_RGMII_MODE, 0);
- if ((phydev->dev_flags & PHY_BRCM_RX_REFCLK_UNUSED) ||
- (phydev->dev_flags & PHY_BRCM_DIS_TXCRXC_NOENRGY) ||
- (phydev->dev_flags & PHY_BRCM_AUTO_PWRDWN_ENABLE))
- bcm54xx_adjust_rxrefclk(phydev);
+ bcm54xx_adjust_rxrefclk(phydev);
if (BRCM_PHY_MODEL(phydev) == PHY_ID_BCM54210E) {
err = bcm54210e_config_init(phydev);
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH net-next v2 3/3] net: phy: broadcom: Wire suspend/resume for BCM54810
2020-02-19 20:00 [PATCH net-next v2 0/3] net: phy: Better support for BCM54810 Florian Fainelli
2020-02-19 20:00 ` [PATCH net-next v2 1/3] net: phy: broadcom: Allow BCM54810 to use bcm54xx_adjust_rxrefclk() Florian Fainelli
2020-02-19 20:00 ` [PATCH net-next v2 2/3] net: phy: broadcom: Have bcm54xx_adjust_rxrefclk() check for flags Florian Fainelli
@ 2020-02-19 20:00 ` Florian Fainelli
2020-02-20 0:37 ` [PATCH net-next v2 0/3] net: phy: Better support " David Miller
3 siblings, 0 replies; 6+ messages in thread
From: Florian Fainelli @ 2020-02-19 20:00 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Andrew Lunn, Heiner Kallweit, Russell King,
David S. Miller, open list
The BCM54810 PHY can use the standard BMCR Power down suspend, but needs
a custom resume routine which first clear the Power down bit, and then
re-initializes the PHY. While in low-power mode, the PHY only accepts
writes to the BMCR register. The datasheet clearly says it:
Reads or writes to any MII register other than MII Control register
(address 00h) while the device is in the standby power-down mode may
cause unpredictable results.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/phy/broadcom.c | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index b4eae84a9195..ab24692a92c6 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -313,6 +313,20 @@ static int bcm54xx_config_init(struct phy_device *phydev)
return 0;
}
+static int bcm54xx_resume(struct phy_device *phydev)
+{
+ int ret;
+
+ /* Writes to register other than BMCR would be ignored
+ * unless we clear the PDOWN bit first
+ */
+ ret = genphy_resume(phydev);
+ if (ret < 0)
+ return ret;
+
+ return bcm54xx_config_init(phydev);
+}
+
static int bcm5482_config_init(struct phy_device *phydev)
{
int err, reg;
@@ -706,6 +720,8 @@ static struct phy_driver broadcom_drivers[] = {
.config_aneg = bcm5481_config_aneg,
.ack_interrupt = bcm_phy_ack_intr,
.config_intr = bcm_phy_config_intr,
+ .suspend = genphy_suspend,
+ .resume = bcm54xx_resume,
}, {
.phy_id = PHY_ID_BCM5482,
.phy_id_mask = 0xfffffff0,
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH net-next v2 2/3] net: phy: broadcom: Have bcm54xx_adjust_rxrefclk() check for flags
2020-02-19 20:00 ` [PATCH net-next v2 2/3] net: phy: broadcom: Have bcm54xx_adjust_rxrefclk() check for flags Florian Fainelli
@ 2020-02-19 20:20 ` Andrew Lunn
0 siblings, 0 replies; 6+ messages in thread
From: Andrew Lunn @ 2020-02-19 20:20 UTC (permalink / raw)
To: Florian Fainelli
Cc: netdev, Heiner Kallweit, Russell King, David S. Miller, open list
On Wed, Feb 19, 2020 at 12:00:48PM -0800, Florian Fainelli wrote:
> bcm54xx_adjust_rxrefclk() already checks for PHY_BRCM_AUTO_PWRDWN_ENABLE
> and PHY_BRCM_DIS_TXCRXC_NOENRGY in order to set the appropriate bit. The
> situation is a bit more complicated with the flag
> PHY_BRCM_RX_REFCLK_UNUSED but essentially amounts to the same situation.
>
> The default setting for the 125MHz clock is to be on for all PHYs and
> we still treat BCM50610 and BCM50610M specifically with the polarity of
> the bit reversed.
>
> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Andrew
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH net-next v2 0/3] net: phy: Better support for BCM54810
2020-02-19 20:00 [PATCH net-next v2 0/3] net: phy: Better support for BCM54810 Florian Fainelli
` (2 preceding siblings ...)
2020-02-19 20:00 ` [PATCH net-next v2 3/3] net: phy: broadcom: Wire suspend/resume for BCM54810 Florian Fainelli
@ 2020-02-20 0:37 ` David Miller
3 siblings, 0 replies; 6+ messages in thread
From: David Miller @ 2020-02-20 0:37 UTC (permalink / raw)
To: f.fainelli; +Cc: netdev, andrew, hkallweit1, linux, linux-kernel
From: Florian Fainelli <f.fainelli@gmail.com>
Date: Wed, 19 Feb 2020 12:00:46 -0800
> This patch series updates the broadcom PHY driver to better support the
> BCM54810 and allow it to make use of the exiting
> bcm54xx_adjust_rxrefclk() as well as fix suspend/resume for it.
>
> Changes in v2:
>
> - added Reviewed-by tags from Andrew for patches #1 and #3
> - expanded commit message in #2 to explain the change
Series applied, thanks Florian.
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2020-02-20 0:37 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-02-19 20:00 [PATCH net-next v2 0/3] net: phy: Better support for BCM54810 Florian Fainelli
2020-02-19 20:00 ` [PATCH net-next v2 1/3] net: phy: broadcom: Allow BCM54810 to use bcm54xx_adjust_rxrefclk() Florian Fainelli
2020-02-19 20:00 ` [PATCH net-next v2 2/3] net: phy: broadcom: Have bcm54xx_adjust_rxrefclk() check for flags Florian Fainelli
2020-02-19 20:20 ` Andrew Lunn
2020-02-19 20:00 ` [PATCH net-next v2 3/3] net: phy: broadcom: Wire suspend/resume for BCM54810 Florian Fainelli
2020-02-20 0:37 ` [PATCH net-next v2 0/3] net: phy: Better support " David Miller
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.