From: Andre Przywara <andre.przywara@arm.com> To: Rob Herring <robh@kernel.org>, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org Cc: Maxime Ripard <mripard@kernel.org>, Robert Richter <rric@kernel.org>, soc@kernel.org, Jon Loeliger <jdl@jdl.com>, Mark Langsdorf <mlangsdo@redhat.com>, Eric Auger <eric.auger@redhat.com>, Will Deacon <will@kernel.org>, Catalin Marinas <catalin.marinas@arm.com> Subject: [PATCH v2 00/13] arm: calxeda: update DTS, bindings and MAINTAINERS Date: Thu, 27 Feb 2020 18:21:57 +0000 [thread overview] Message-ID: <20200227182210.89512-1-andre.przywara@arm.com> (raw) Hi, some smaller changes, as pointed out by Maxime. Many thanks! ------------------ This series is an answer to the attempt [1] of removing the Calxeda Highbank platform support from the kernel. Apart from the pending removal of ARM32 host KVM support from the kernel, the lack of proper DT schema bindings was another major reason for Rob's series. This series addresses this. The first four patches adjust the .dts files to pass the existing (mostly generic) DT schema binding checks. Those changes should not affect the functionality. The following eight patches then convert the "prose" DT binding documentation to the json-schema format, so that the automatic checking actually does something useful. After those patches "make dtbs_check" comes back clean for the two .dts files in the kernel, and "dt_validate -m" reports only those three not-covered nodes (on Highbank, only the last one on Midway): arm,cortex-a9-twd-timer arm,cortex-a9-twd-wdt calxeda,hb-sdhci The first two are generic ARM devices, for which the binding doc just does not have been converted yet. The SDHCI controller is actually disabled in the DTs, and the SD slot is populated on very few special systems only, also there has never been a driver in the kernel for this device anyway. The final patch then changes the MAINTAINERS file to hand over the maintainership to me. I have a working machine under my desk and have some interest in keeping this platform support alive. Changelog: v1 ... v2: - Remove unneeded property type from clocks and sgpio-gpio - add additionalProperties: false to bindings missing it before - limit number in "phydev" to the hardware constraint of 5 bits - add required: properties to l2ecc binding - fix enumeration of compatible strings in calxeda-ddr-ctrlr Cheers, Andre. [1] https://lore.kernel.org/linux-arm-kernel/20200218171321.30990-1-robh@kernel.org/ Andre Przywara (13): arm: dts: calxeda: Basic DT file fixes arm: dts: calxeda: Provide UART clock arm: dts: calxeda: Fix interrupt grouping arm: dts: calxeda: Group port-phys and sgpio-gpio items dt-bindings: clock: Convert Calxeda clock bindings to json-schema dt-bindings: sata: Convert Calxeda SATA controller to json-schema dt-bindings: net: Convert Calxeda Ethernet binding to json-schema dt-bindings: phy: Convert Calxeda ComboPHY binding to json-schema dt-bindings: arm: Convert Calxeda L2 cache controller to json-schema dt-bindings: memory-controllers: convert Calxeda DDR to json-schema dt-bindings: ipmi: Convert IPMI-SMIC bindings to json-schema dt-bindings: arm: Add Calxeda system registers json-schema binding MAINTAINERS: Update Calxeda Highbank maintainership .../bindings/arm/calxeda/hb-sregs.yaml | 47 +++++++++ .../devicetree/bindings/arm/calxeda/l2ecc.txt | 15 --- .../bindings/arm/calxeda/l2ecc.yaml | 36 +++++++ .../devicetree/bindings/ata/sata_highbank.txt | 44 --------- .../bindings/ata/sata_highbank.yaml | 96 +++++++++++++++++++ .../devicetree/bindings/clock/calxeda.txt | 17 ---- .../devicetree/bindings/clock/calxeda.yaml | 83 ++++++++++++++++ .../devicetree/bindings/ipmi/ipmi-smic.txt | 25 ----- .../devicetree/bindings/ipmi/ipmi-smic.yaml | 56 +++++++++++ .../memory-controllers/calxeda-ddr-ctrlr.txt | 16 ---- .../memory-controllers/calxeda-ddr-ctrlr.yaml | 41 ++++++++ .../devicetree/bindings/net/calxeda-xgmac.txt | 18 ---- .../bindings/net/calxeda-xgmac.yaml | 47 +++++++++ .../bindings/phy/calxeda-combophy.txt | 17 ---- .../bindings/phy/calxeda-combophy.yaml | 47 +++++++++ MAINTAINERS | 2 +- arch/arm/boot/dts/ecx-2000.dts | 5 +- arch/arm/boot/dts/ecx-common.dtsi | 17 ++-- arch/arm/boot/dts/highbank.dts | 11 +-- 19 files changed, 468 insertions(+), 172 deletions(-) create mode 100644 Documentation/devicetree/bindings/arm/calxeda/hb-sregs.yaml delete mode 100644 Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt create mode 100644 Documentation/devicetree/bindings/arm/calxeda/l2ecc.yaml delete mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.txt create mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.yaml delete mode 100644 Documentation/devicetree/bindings/clock/calxeda.txt create mode 100644 Documentation/devicetree/bindings/clock/calxeda.yaml delete mode 100644 Documentation/devicetree/bindings/ipmi/ipmi-smic.txt create mode 100644 Documentation/devicetree/bindings/ipmi/ipmi-smic.yaml delete mode 100644 Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.yaml delete mode 100644 Documentation/devicetree/bindings/net/calxeda-xgmac.txt create mode 100644 Documentation/devicetree/bindings/net/calxeda-xgmac.yaml delete mode 100644 Documentation/devicetree/bindings/phy/calxeda-combophy.txt create mode 100644 Documentation/devicetree/bindings/phy/calxeda-combophy.yaml -- 2.17.1 *** BLURB HERE *** Andre Przywara (13): arm: dts: calxeda: Basic DT file fixes arm: dts: calxeda: Provide UART clock arm: dts: calxeda: Fix interrupt grouping arm: dts: calxeda: Group port-phys and sgpio-gpio items dt-bindings: clock: Convert Calxeda clock bindings to json-schema dt-bindings: sata: Convert Calxeda SATA controller to json-schema dt-bindings: net: Convert Calxeda Ethernet binding to json-schema dt-bindings: phy: Convert Calxeda ComboPHY binding to json-schema dt-bindings: arm: Convert Calxeda L2 cache controller to json-schema dt-bindings: memory-controllers: Convert Calxeda DDR to json-schema dt-bindings: ipmi: Convert IPMI-SMIC bindings to json-schema dt-bindings: arm: Add Calxeda system registers json-schema binding MAINTAINERS: Update Calxeda Highbank maintainership .../bindings/arm/calxeda/hb-sregs.yaml | 49 ++++++++++ .../devicetree/bindings/arm/calxeda/l2ecc.txt | 15 --- .../bindings/arm/calxeda/l2ecc.yaml | 43 +++++++++ .../devicetree/bindings/ata/sata_highbank.txt | 44 --------- .../bindings/ata/sata_highbank.yaml | 95 +++++++++++++++++++ .../devicetree/bindings/clock/calxeda.txt | 17 ---- .../devicetree/bindings/clock/calxeda.yaml | 82 ++++++++++++++++ .../devicetree/bindings/ipmi/ipmi-smic.txt | 25 ----- .../devicetree/bindings/ipmi/ipmi-smic.yaml | 56 +++++++++++ .../memory-controllers/calxeda-ddr-ctrlr.txt | 16 ---- .../memory-controllers/calxeda-ddr-ctrlr.yaml | 42 ++++++++ .../devicetree/bindings/net/calxeda-xgmac.txt | 18 ---- .../bindings/net/calxeda-xgmac.yaml | 49 ++++++++++ .../bindings/phy/calxeda-combophy.txt | 17 ---- .../bindings/phy/calxeda-combophy.yaml | 51 ++++++++++ MAINTAINERS | 2 +- arch/arm/boot/dts/ecx-2000.dts | 5 +- arch/arm/boot/dts/ecx-common.dtsi | 17 ++-- arch/arm/boot/dts/highbank.dts | 11 +-- 19 files changed, 482 insertions(+), 172 deletions(-) create mode 100644 Documentation/devicetree/bindings/arm/calxeda/hb-sregs.yaml delete mode 100644 Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt create mode 100644 Documentation/devicetree/bindings/arm/calxeda/l2ecc.yaml delete mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.txt create mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.yaml delete mode 100644 Documentation/devicetree/bindings/clock/calxeda.txt create mode 100644 Documentation/devicetree/bindings/clock/calxeda.yaml delete mode 100644 Documentation/devicetree/bindings/ipmi/ipmi-smic.txt create mode 100644 Documentation/devicetree/bindings/ipmi/ipmi-smic.yaml delete mode 100644 Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.yaml delete mode 100644 Documentation/devicetree/bindings/net/calxeda-xgmac.txt create mode 100644 Documentation/devicetree/bindings/net/calxeda-xgmac.yaml delete mode 100644 Documentation/devicetree/bindings/phy/calxeda-combophy.txt create mode 100644 Documentation/devicetree/bindings/phy/calxeda-combophy.yaml -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: Andre Przywara <andre.przywara@arm.com> To: Rob Herring <robh@kernel.org>, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org Cc: Jon Loeliger <jdl@jdl.com>, Mark Langsdorf <mlangsdo@redhat.com>, Robert Richter <rric@kernel.org>, Catalin Marinas <catalin.marinas@arm.com>, Maxime Ripard <mripard@kernel.org>, Eric Auger <eric.auger@redhat.com>, soc@kernel.org, Will Deacon <will@kernel.org> Subject: [PATCH v2 00/13] arm: calxeda: update DTS, bindings and MAINTAINERS Date: Thu, 27 Feb 2020 18:21:57 +0000 [thread overview] Message-ID: <20200227182210.89512-1-andre.przywara@arm.com> (raw) Hi, some smaller changes, as pointed out by Maxime. Many thanks! ------------------ This series is an answer to the attempt [1] of removing the Calxeda Highbank platform support from the kernel. Apart from the pending removal of ARM32 host KVM support from the kernel, the lack of proper DT schema bindings was another major reason for Rob's series. This series addresses this. The first four patches adjust the .dts files to pass the existing (mostly generic) DT schema binding checks. Those changes should not affect the functionality. The following eight patches then convert the "prose" DT binding documentation to the json-schema format, so that the automatic checking actually does something useful. After those patches "make dtbs_check" comes back clean for the two .dts files in the kernel, and "dt_validate -m" reports only those three not-covered nodes (on Highbank, only the last one on Midway): arm,cortex-a9-twd-timer arm,cortex-a9-twd-wdt calxeda,hb-sdhci The first two are generic ARM devices, for which the binding doc just does not have been converted yet. The SDHCI controller is actually disabled in the DTs, and the SD slot is populated on very few special systems only, also there has never been a driver in the kernel for this device anyway. The final patch then changes the MAINTAINERS file to hand over the maintainership to me. I have a working machine under my desk and have some interest in keeping this platform support alive. Changelog: v1 ... v2: - Remove unneeded property type from clocks and sgpio-gpio - add additionalProperties: false to bindings missing it before - limit number in "phydev" to the hardware constraint of 5 bits - add required: properties to l2ecc binding - fix enumeration of compatible strings in calxeda-ddr-ctrlr Cheers, Andre. [1] https://lore.kernel.org/linux-arm-kernel/20200218171321.30990-1-robh@kernel.org/ Andre Przywara (13): arm: dts: calxeda: Basic DT file fixes arm: dts: calxeda: Provide UART clock arm: dts: calxeda: Fix interrupt grouping arm: dts: calxeda: Group port-phys and sgpio-gpio items dt-bindings: clock: Convert Calxeda clock bindings to json-schema dt-bindings: sata: Convert Calxeda SATA controller to json-schema dt-bindings: net: Convert Calxeda Ethernet binding to json-schema dt-bindings: phy: Convert Calxeda ComboPHY binding to json-schema dt-bindings: arm: Convert Calxeda L2 cache controller to json-schema dt-bindings: memory-controllers: convert Calxeda DDR to json-schema dt-bindings: ipmi: Convert IPMI-SMIC bindings to json-schema dt-bindings: arm: Add Calxeda system registers json-schema binding MAINTAINERS: Update Calxeda Highbank maintainership .../bindings/arm/calxeda/hb-sregs.yaml | 47 +++++++++ .../devicetree/bindings/arm/calxeda/l2ecc.txt | 15 --- .../bindings/arm/calxeda/l2ecc.yaml | 36 +++++++ .../devicetree/bindings/ata/sata_highbank.txt | 44 --------- .../bindings/ata/sata_highbank.yaml | 96 +++++++++++++++++++ .../devicetree/bindings/clock/calxeda.txt | 17 ---- .../devicetree/bindings/clock/calxeda.yaml | 83 ++++++++++++++++ .../devicetree/bindings/ipmi/ipmi-smic.txt | 25 ----- .../devicetree/bindings/ipmi/ipmi-smic.yaml | 56 +++++++++++ .../memory-controllers/calxeda-ddr-ctrlr.txt | 16 ---- .../memory-controllers/calxeda-ddr-ctrlr.yaml | 41 ++++++++ .../devicetree/bindings/net/calxeda-xgmac.txt | 18 ---- .../bindings/net/calxeda-xgmac.yaml | 47 +++++++++ .../bindings/phy/calxeda-combophy.txt | 17 ---- .../bindings/phy/calxeda-combophy.yaml | 47 +++++++++ MAINTAINERS | 2 +- arch/arm/boot/dts/ecx-2000.dts | 5 +- arch/arm/boot/dts/ecx-common.dtsi | 17 ++-- arch/arm/boot/dts/highbank.dts | 11 +-- 19 files changed, 468 insertions(+), 172 deletions(-) create mode 100644 Documentation/devicetree/bindings/arm/calxeda/hb-sregs.yaml delete mode 100644 Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt create mode 100644 Documentation/devicetree/bindings/arm/calxeda/l2ecc.yaml delete mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.txt create mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.yaml delete mode 100644 Documentation/devicetree/bindings/clock/calxeda.txt create mode 100644 Documentation/devicetree/bindings/clock/calxeda.yaml delete mode 100644 Documentation/devicetree/bindings/ipmi/ipmi-smic.txt create mode 100644 Documentation/devicetree/bindings/ipmi/ipmi-smic.yaml delete mode 100644 Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.yaml delete mode 100644 Documentation/devicetree/bindings/net/calxeda-xgmac.txt create mode 100644 Documentation/devicetree/bindings/net/calxeda-xgmac.yaml delete mode 100644 Documentation/devicetree/bindings/phy/calxeda-combophy.txt create mode 100644 Documentation/devicetree/bindings/phy/calxeda-combophy.yaml -- 2.17.1 *** BLURB HERE *** Andre Przywara (13): arm: dts: calxeda: Basic DT file fixes arm: dts: calxeda: Provide UART clock arm: dts: calxeda: Fix interrupt grouping arm: dts: calxeda: Group port-phys and sgpio-gpio items dt-bindings: clock: Convert Calxeda clock bindings to json-schema dt-bindings: sata: Convert Calxeda SATA controller to json-schema dt-bindings: net: Convert Calxeda Ethernet binding to json-schema dt-bindings: phy: Convert Calxeda ComboPHY binding to json-schema dt-bindings: arm: Convert Calxeda L2 cache controller to json-schema dt-bindings: memory-controllers: Convert Calxeda DDR to json-schema dt-bindings: ipmi: Convert IPMI-SMIC bindings to json-schema dt-bindings: arm: Add Calxeda system registers json-schema binding MAINTAINERS: Update Calxeda Highbank maintainership .../bindings/arm/calxeda/hb-sregs.yaml | 49 ++++++++++ .../devicetree/bindings/arm/calxeda/l2ecc.txt | 15 --- .../bindings/arm/calxeda/l2ecc.yaml | 43 +++++++++ .../devicetree/bindings/ata/sata_highbank.txt | 44 --------- .../bindings/ata/sata_highbank.yaml | 95 +++++++++++++++++++ .../devicetree/bindings/clock/calxeda.txt | 17 ---- .../devicetree/bindings/clock/calxeda.yaml | 82 ++++++++++++++++ .../devicetree/bindings/ipmi/ipmi-smic.txt | 25 ----- .../devicetree/bindings/ipmi/ipmi-smic.yaml | 56 +++++++++++ .../memory-controllers/calxeda-ddr-ctrlr.txt | 16 ---- .../memory-controllers/calxeda-ddr-ctrlr.yaml | 42 ++++++++ .../devicetree/bindings/net/calxeda-xgmac.txt | 18 ---- .../bindings/net/calxeda-xgmac.yaml | 49 ++++++++++ .../bindings/phy/calxeda-combophy.txt | 17 ---- .../bindings/phy/calxeda-combophy.yaml | 51 ++++++++++ MAINTAINERS | 2 +- arch/arm/boot/dts/ecx-2000.dts | 5 +- arch/arm/boot/dts/ecx-common.dtsi | 17 ++-- arch/arm/boot/dts/highbank.dts | 11 +-- 19 files changed, 482 insertions(+), 172 deletions(-) create mode 100644 Documentation/devicetree/bindings/arm/calxeda/hb-sregs.yaml delete mode 100644 Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt create mode 100644 Documentation/devicetree/bindings/arm/calxeda/l2ecc.yaml delete mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.txt create mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.yaml delete mode 100644 Documentation/devicetree/bindings/clock/calxeda.txt create mode 100644 Documentation/devicetree/bindings/clock/calxeda.yaml delete mode 100644 Documentation/devicetree/bindings/ipmi/ipmi-smic.txt create mode 100644 Documentation/devicetree/bindings/ipmi/ipmi-smic.yaml delete mode 100644 Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.yaml delete mode 100644 Documentation/devicetree/bindings/net/calxeda-xgmac.txt create mode 100644 Documentation/devicetree/bindings/net/calxeda-xgmac.yaml delete mode 100644 Documentation/devicetree/bindings/phy/calxeda-combophy.txt create mode 100644 Documentation/devicetree/bindings/phy/calxeda-combophy.yaml -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2020-02-27 18:22 UTC|newest] Thread overview: 51+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-02-27 18:21 Andre Przywara [this message] 2020-02-27 18:21 ` [PATCH v2 00/13] arm: calxeda: update DTS, bindings and MAINTAINERS Andre Przywara 2020-02-27 18:21 ` [PATCH v2 01/13] arm: dts: calxeda: Basic DT file fixes Andre Przywara 2020-02-27 18:21 ` Andre Przywara 2020-02-27 21:42 ` Rob Herring 2020-02-27 21:42 ` Rob Herring 2020-02-27 18:21 ` [PATCH v2 02/13] arm: dts: calxeda: Provide UART clock Andre Przywara 2020-02-27 18:21 ` Andre Przywara 2020-02-27 21:43 ` Rob Herring 2020-02-27 21:43 ` Rob Herring 2020-02-27 18:22 ` [PATCH v2 03/13] arm: dts: calxeda: Fix interrupt grouping Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-27 21:45 ` Rob Herring 2020-02-27 21:45 ` Rob Herring 2020-02-27 18:22 ` [PATCH v2 04/13] arm: dts: calxeda: Group port-phys and sgpio-gpio items Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-27 21:45 ` Rob Herring 2020-02-27 21:45 ` Rob Herring 2020-02-27 18:22 ` [PATCH v2 05/13] dt-bindings: clock: Convert Calxeda clock bindings to json-schema Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-28 22:20 ` Stephen Boyd 2020-02-27 18:22 ` [PATCH v2 06/13] dt-bindings: sata: Convert Calxeda SATA controller " Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-27 22:05 ` Rob Herring 2020-02-27 22:05 ` Rob Herring 2020-02-27 18:22 ` [PATCH v2 07/13] dt-bindings: net: Convert Calxeda Ethernet binding " Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-27 18:22 ` [PATCH v2 08/13] dt-bindings: phy: Convert Calxeda ComboPHY " Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-27 18:22 ` [PATCH v2 09/13] dt-bindings: arm: Convert Calxeda L2 cache controller " Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-27 18:22 ` [PATCH v2 10/13] dt-bindings: memory-controllers: Convert Calxeda DDR " Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-27 18:22 ` [PATCH v2 11/13] dt-bindings: ipmi: Convert IPMI-SMIC bindings " Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-27 22:21 ` Rob Herring 2020-02-27 22:21 ` Rob Herring 2020-02-28 0:21 ` André Przywara 2020-02-28 0:21 ` André Przywara 2020-02-27 18:22 ` [PATCH v2 12/13] dt-bindings: arm: Add Calxeda system registers json-schema binding Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-27 22:22 ` Rob Herring 2020-02-27 22:22 ` Rob Herring 2020-02-27 18:22 ` [PATCH v2 13/13] MAINTAINERS: Update Calxeda Highbank maintainership Andre Przywara 2020-02-27 18:22 ` Andre Przywara 2020-02-27 22:35 ` Rob Herring 2020-02-27 22:35 ` Rob Herring 2020-02-28 0:39 ` Olof Johansson 2020-02-28 0:39 ` Olof Johansson 2020-02-28 11:53 ` Andre Przywara 2020-02-28 11:53 ` Andre Przywara
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20200227182210.89512-1-andre.przywara@arm.com \ --to=andre.przywara@arm.com \ --cc=catalin.marinas@arm.com \ --cc=devicetree@vger.kernel.org \ --cc=eric.auger@redhat.com \ --cc=jdl@jdl.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=mlangsdo@redhat.com \ --cc=mripard@kernel.org \ --cc=robh@kernel.org \ --cc=rric@kernel.org \ --cc=soc@kernel.org \ --cc=will@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.