* [RESEND PATCH v2 0/3] Add support for Chrontel CH7033 VGA/DVI Encoder @ 2020-03-07 19:07 ` Lubomir Rintel 0 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:07 UTC (permalink / raw) To: Andrzej Hajda Cc: Neil Armstrong, Laurent Pinchart, Jonas Karlman, Jernej Skrabec, Rob Herring, Mark Rutland, David Airlie, Daniel Vetter, dri-devel, devicetree, linux-kernel Hi, chained to this message is a driver for CH7033 along with device tree binding docs. I'm hoping that it could perhaps make it into 5.7. Please take a look. Previous submission [1] contained the exact same patches as this one, but at that time they relied on Laurent's omapdrm/bridge/devel branch that has been merged since. [1] https://lore.kernel.org/lkml/20200221162743.14141-1-lkundrak@v3.sk/ Tested to work well on MMP3-based Dell Wyse 3020. There's no datasheet or programming manual available. Thanks, Lubo ^ permalink raw reply [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 0/3] Add support for Chrontel CH7033 VGA/DVI Encoder @ 2020-03-07 19:07 ` Lubomir Rintel 0 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:07 UTC (permalink / raw) To: Andrzej Hajda Cc: Mark Rutland, devicetree, Jernej Skrabec, Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel, dri-devel, Rob Herring, Laurent Pinchart Hi, chained to this message is a driver for CH7033 along with device tree binding docs. I'm hoping that it could perhaps make it into 5.7. Please take a look. Previous submission [1] contained the exact same patches as this one, but at that time they relied on Laurent's omapdrm/bridge/devel branch that has been merged since. [1] https://lore.kernel.org/lkml/20200221162743.14141-1-lkundrak@v3.sk/ Tested to work well on MMP3-based Dell Wyse 3020. There's no datasheet or programming manual available. Thanks, Lubo _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 0/3] Add support for Chrontel CH7033 VGA/DVI Encoder @ 2020-03-07 19:07 ` Lubomir Rintel 0 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:07 UTC (permalink / raw) To: Andrzej Hajda Cc: Mark Rutland, devicetree, Jernej Skrabec, Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel, dri-devel, Rob Herring, Laurent Pinchart Hi, chained to this message is a driver for CH7033 along with device tree binding docs. I'm hoping that it could perhaps make it into 5.7. Please take a look. Previous submission [1] contained the exact same patches as this one, but at that time they relied on Laurent's omapdrm/bridge/devel branch that has been merged since. [1] https://lore.kernel.org/lkml/20200221162743.14141-1-lkundrak@v3.sk/ Tested to work well on MMP3-based Dell Wyse 3020. There's no datasheet or programming manual available. Thanks, Lubo _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 1/3] dt-bindings: Add vendor prefix for Chrontel, Inc. 2020-03-07 19:07 ` Lubomir Rintel (?) @ 2020-03-07 19:07 ` Lubomir Rintel -1 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:07 UTC (permalink / raw) To: Andrzej Hajda Cc: Neil Armstrong, Laurent Pinchart, Jonas Karlman, Jernej Skrabec, Rob Herring, Mark Rutland, David Airlie, Daniel Vetter, dri-devel, devicetree, linux-kernel, Lubomir Rintel, Rob Herring Chrontel makes encoders for video displays and perhaps other stuff. Their web site is http://www.chrontel.com/. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Acked-by: Rob Herring <robh@kernel.org> --- Changes since v1: - Collect Rob's ack Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index a2da166df1bc7..0ab86d876f4d2 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -185,6 +185,8 @@ patternProperties: description: ChipOne "^chipspark,.*": description: ChipSPARK + "^chrontel,.*": + description: Chrontel, Inc. "^chrp,.*": description: Common Hardware Reference Platform "^chunghwa,.*": -- 2.24.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 1/3] dt-bindings: Add vendor prefix for Chrontel, Inc. @ 2020-03-07 19:07 ` Lubomir Rintel 0 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:07 UTC (permalink / raw) To: Andrzej Hajda Cc: Mark Rutland, devicetree, Jernej Skrabec, Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel, dri-devel, Lubomir Rintel, Rob Herring, Laurent Pinchart Chrontel makes encoders for video displays and perhaps other stuff. Their web site is http://www.chrontel.com/. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Acked-by: Rob Herring <robh@kernel.org> --- Changes since v1: - Collect Rob's ack Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index a2da166df1bc7..0ab86d876f4d2 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -185,6 +185,8 @@ patternProperties: description: ChipOne "^chipspark,.*": description: ChipSPARK + "^chrontel,.*": + description: Chrontel, Inc. "^chrp,.*": description: Common Hardware Reference Platform "^chunghwa,.*": -- 2.24.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 1/3] dt-bindings: Add vendor prefix for Chrontel, Inc. @ 2020-03-07 19:07 ` Lubomir Rintel 0 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:07 UTC (permalink / raw) To: Andrzej Hajda Cc: Mark Rutland, devicetree, Jernej Skrabec, Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel, dri-devel, Lubomir Rintel, Rob Herring, Laurent Pinchart Chrontel makes encoders for video displays and perhaps other stuff. Their web site is http://www.chrontel.com/. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Acked-by: Rob Herring <robh@kernel.org> --- Changes since v1: - Collect Rob's ack Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index a2da166df1bc7..0ab86d876f4d2 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -185,6 +185,8 @@ patternProperties: description: ChipOne "^chipspark,.*": description: ChipSPARK + "^chrontel,.*": + description: Chrontel, Inc. "^chrp,.*": description: Common Hardware Reference Platform "^chunghwa,.*": -- 2.24.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 2/3] dt-bindings: display: Add Chrontel CH7033 Video Encoder binding 2020-03-07 19:07 ` Lubomir Rintel (?) @ 2020-03-07 19:07 ` Lubomir Rintel -1 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:07 UTC (permalink / raw) To: Andrzej Hajda Cc: Neil Armstrong, Laurent Pinchart, Jonas Karlman, Jernej Skrabec, Rob Herring, Mark Rutland, David Airlie, Daniel Vetter, dri-devel, devicetree, linux-kernel, Lubomir Rintel, Rob Herring Add binding document for the Chrontel CH7033 VGA/DVI/HDMI Encoder. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Reviewed-by: Rob Herring <robh@kernel.org> --- Changes since v1: - Dual licensed with BSD-2-Clause - Collected Rob's reviewed-by tag .../display/bridge/chrontel,ch7033.yaml | 86 +++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml diff --git a/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml b/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml new file mode 100644 index 0000000000000..dc97f34fbfe0f --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk> +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/chrontel,ch7033.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Chrontel CH7033 Video Encoder Device Tree Bindings + +maintainers: + - Lubomir Rintel <lkundrak@v3.sk> + +properties: + compatible: + const: chrontel,ch7033 + + reg: + maxItems: 1 + description: I2C address of the device + + ports: + type: object + + properties: + port@0: + type: object + description: | + Video port for RGB input. + + port@1: + type: object + description: | + DVI port, should be connected to a node compatible with the + dvi-connector binding. + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - ports + +additionalProperties: false + +examples: + - | + dvi-connector { + compatible = "dvi-connector"; + ddc-i2c-bus = <&twsi5>; + hpd-gpios = <&gpio 62 GPIO_ACTIVE_LOW>; + digital; + analog; + + port { + dvi_in: endpoint { + remote-endpoint = <&encoder_out>; + }; + }; + }; + + vga-dvi-encoder@76 { + compatible = "chrontel,ch7033"; + reg = <0x76>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + endpoint { + remote-endpoint = <&lcd0_rgb_out>; + }; + }; + + encoder_out: port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&dvi_in>; + }; + }; + + }; + }; -- 2.24.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 2/3] dt-bindings: display: Add Chrontel CH7033 Video Encoder binding @ 2020-03-07 19:07 ` Lubomir Rintel 0 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:07 UTC (permalink / raw) To: Andrzej Hajda Cc: Mark Rutland, devicetree, Jernej Skrabec, Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel, dri-devel, Lubomir Rintel, Rob Herring, Laurent Pinchart Add binding document for the Chrontel CH7033 VGA/DVI/HDMI Encoder. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Reviewed-by: Rob Herring <robh@kernel.org> --- Changes since v1: - Dual licensed with BSD-2-Clause - Collected Rob's reviewed-by tag .../display/bridge/chrontel,ch7033.yaml | 86 +++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml diff --git a/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml b/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml new file mode 100644 index 0000000000000..dc97f34fbfe0f --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk> +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/chrontel,ch7033.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Chrontel CH7033 Video Encoder Device Tree Bindings + +maintainers: + - Lubomir Rintel <lkundrak@v3.sk> + +properties: + compatible: + const: chrontel,ch7033 + + reg: + maxItems: 1 + description: I2C address of the device + + ports: + type: object + + properties: + port@0: + type: object + description: | + Video port for RGB input. + + port@1: + type: object + description: | + DVI port, should be connected to a node compatible with the + dvi-connector binding. + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - ports + +additionalProperties: false + +examples: + - | + dvi-connector { + compatible = "dvi-connector"; + ddc-i2c-bus = <&twsi5>; + hpd-gpios = <&gpio 62 GPIO_ACTIVE_LOW>; + digital; + analog; + + port { + dvi_in: endpoint { + remote-endpoint = <&encoder_out>; + }; + }; + }; + + vga-dvi-encoder@76 { + compatible = "chrontel,ch7033"; + reg = <0x76>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + endpoint { + remote-endpoint = <&lcd0_rgb_out>; + }; + }; + + encoder_out: port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&dvi_in>; + }; + }; + + }; + }; -- 2.24.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 2/3] dt-bindings: display: Add Chrontel CH7033 Video Encoder binding @ 2020-03-07 19:07 ` Lubomir Rintel 0 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:07 UTC (permalink / raw) To: Andrzej Hajda Cc: Mark Rutland, devicetree, Jernej Skrabec, Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel, dri-devel, Lubomir Rintel, Rob Herring, Laurent Pinchart Add binding document for the Chrontel CH7033 VGA/DVI/HDMI Encoder. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Reviewed-by: Rob Herring <robh@kernel.org> --- Changes since v1: - Dual licensed with BSD-2-Clause - Collected Rob's reviewed-by tag .../display/bridge/chrontel,ch7033.yaml | 86 +++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml diff --git a/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml b/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml new file mode 100644 index 0000000000000..dc97f34fbfe0f --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk> +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/chrontel,ch7033.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Chrontel CH7033 Video Encoder Device Tree Bindings + +maintainers: + - Lubomir Rintel <lkundrak@v3.sk> + +properties: + compatible: + const: chrontel,ch7033 + + reg: + maxItems: 1 + description: I2C address of the device + + ports: + type: object + + properties: + port@0: + type: object + description: | + Video port for RGB input. + + port@1: + type: object + description: | + DVI port, should be connected to a node compatible with the + dvi-connector binding. + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - ports + +additionalProperties: false + +examples: + - | + dvi-connector { + compatible = "dvi-connector"; + ddc-i2c-bus = <&twsi5>; + hpd-gpios = <&gpio 62 GPIO_ACTIVE_LOW>; + digital; + analog; + + port { + dvi_in: endpoint { + remote-endpoint = <&encoder_out>; + }; + }; + }; + + vga-dvi-encoder@76 { + compatible = "chrontel,ch7033"; + reg = <0x76>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + endpoint { + remote-endpoint = <&lcd0_rgb_out>; + }; + }; + + encoder_out: port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&dvi_in>; + }; + }; + + }; + }; -- 2.24.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 3/3] drm/bridge: chrontel-ch7033: Add a new driver 2020-03-07 19:07 ` Lubomir Rintel (?) @ 2020-03-07 19:08 ` Lubomir Rintel -1 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:08 UTC (permalink / raw) To: Andrzej Hajda Cc: Neil Armstrong, Laurent Pinchart, Jonas Karlman, Jernej Skrabec, Rob Herring, Mark Rutland, David Airlie, Daniel Vetter, dri-devel, devicetree, linux-kernel, Lubomir Rintel This is a driver for video encoder with VGA and DVI/HDMI outputs. There is no documentation for the chip -- the operation was guessed from what was sniffed on a Dell Wyse 3020 ThinOS terminal, the register names come from the ch7035 driver in Mediatek's GPL code dump. Only bare minimum is implemented -- no fancy stuff, such as scaling. That would only worsen our misery. We don't load the firmware and we don't need to even bother enabling the MCU. There are probably no distributable firmware images anyway. Just like the tda998x driver, this one uses the component framework and adds an encoder on component bind, so that it works with the Armada DRM driver. Tested with a handful of monitors ranging from 1024x768@75 to 1400x1050@60, with VGA as well as DVI. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> --- Changes since v1: - Sort the includes - Drop a useless model id read - Chain to the bridge-connector instead of dealing with the HPD/EDID readout machinery ourselves - Utilize regmap to access the registers drivers/gpu/drm/bridge/Kconfig | 10 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/chrontel-ch7033.c | 675 +++++++++++++++++++++++ 3 files changed, 686 insertions(+) create mode 100644 drivers/gpu/drm/bridge/chrontel-ch7033.c diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig index aaed2347ace9d..0ebc72d62a5b2 100644 --- a/drivers/gpu/drm/bridge/Kconfig +++ b/drivers/gpu/drm/bridge/Kconfig @@ -27,6 +27,16 @@ config DRM_CDNS_DSI Support Cadence DPI to DSI bridge. This is an internal bridge and is meant to be directly embedded in a SoC. +config DRM_CHRONTEL_CH7033 + tristate "Chrontel CH7033 Video Encoder" + depends on OF + select DRM_KMS_HELPER + help + Enable support for the Chrontel CH7033 VGA/DVI/HDMI Encoder, as + found in the Dell Wyse 3020 thin client. + + If in doubt, say "N". + config DRM_DISPLAY_CONNECTOR tristate "Display connector support" depends on OF diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile index 6fb062b5b0f04..a844315feddb4 100644 --- a/drivers/gpu/drm/bridge/Makefile +++ b/drivers/gpu/drm/bridge/Makefile @@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o +obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o diff --git a/drivers/gpu/drm/bridge/chrontel-ch7033.c b/drivers/gpu/drm/bridge/chrontel-ch7033.c new file mode 100644 index 0000000000000..342b2e2bd2b1c --- /dev/null +++ b/drivers/gpu/drm/bridge/chrontel-ch7033.c @@ -0,0 +1,675 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Chrontel CH7033 Video Encoder Driver + * + * Copyright (C) 2019,2020 Lubomir Rintel + */ + +#include <linux/component.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/regmap.h> + +#include <drm/drm_atomic_helper.h> +#include <drm/drm_bridge.h> +#include <drm/drm_edid.h> +#include <drm/drm_of.h> +#include <drm/drm_print.h> +#include <drm/drm_probe_helper.h> + +/* Page 0, Register 0x07 */ +enum { + DRI_PD = BIT(3), + IO_PD = BIT(5), +}; + +/* Page 0, Register 0x08 */ +enum { + DRI_PDDRI = GENMASK(7, 4), + PDDAC = GENMASK(3, 1), + PANEN = BIT(0), +}; + +/* Page 0, Register 0x09 */ +enum { + DPD = BIT(7), + GCKOFF = BIT(6), + TV_BP = BIT(5), + SCLPD = BIT(4), + SDPD = BIT(3), + VGA_PD = BIT(2), + HDBKPD = BIT(1), + HDMI_PD = BIT(0), +}; + +/* Page 0, Register 0x0a */ +enum { + MEMINIT = BIT(7), + MEMIDLE = BIT(6), + MEMPD = BIT(5), + STOP = BIT(4), + LVDS_PD = BIT(3), + HD_DVIB = BIT(2), + HDCP_PD = BIT(1), + MCU_PD = BIT(0), +}; + +/* Page 0, Register 0x18 */ +enum { + IDF = GENMASK(7, 4), + INTEN = BIT(3), + SWAP = GENMASK(2, 0), +}; + +enum { + BYTE_SWAP_RGB = 0, + BYTE_SWAP_RBG = 1, + BYTE_SWAP_GRB = 2, + BYTE_SWAP_GBR = 3, + BYTE_SWAP_BRG = 4, + BYTE_SWAP_BGR = 5, +}; + +/* Page 0, Register 0x19 */ +enum { + HPO_I = BIT(5), + VPO_I = BIT(4), + DEPO_I = BIT(3), + CRYS_EN = BIT(2), + GCLKFREQ = GENMASK(2, 0), +}; + +/* Page 0, Register 0x2e */ +enum { + HFLIP = BIT(7), + VFLIP = BIT(6), + DEPO_O = BIT(5), + HPO_O = BIT(4), + VPO_O = BIT(3), + TE = GENMASK(2, 0), +}; + +/* Page 0, Register 0x2b */ +enum { + SWAPS = GENMASK(7, 4), + VFMT = GENMASK(3, 0), +}; + +/* Page 0, Register 0x54 */ +enum { + COMP_BP = BIT(7), + DAC_EN_T = BIT(6), + HWO_HDMI_HI = GENMASK(5, 3), + HOO_HDMI_HI = GENMASK(2, 0), +}; + +/* Page 0, Register 0x57 */ +enum { + FLDSEN = BIT(7), + VWO_HDMI_HI = GENMASK(5, 3), + VOO_HDMI_HI = GENMASK(2, 0), +}; + +/* Page 0, Register 0x7e */ +enum { + HDMI_LVDS_SEL = BIT(7), + DE_GEN = BIT(6), + PWM_INDEX_HI = BIT(5), + USE_DE = BIT(4), + R_INT = GENMASK(3, 0), +}; + +/* Page 1, Register 0x07 */ +enum { + BPCKSEL = BIT(7), + DRI_CMFB_EN = BIT(6), + CEC_PUEN = BIT(5), + CEC_T = BIT(3), + CKINV = BIT(2), + CK_TVINV = BIT(1), + DRI_CKS2 = BIT(0), +}; + +/* Page 1, Register 0x08 */ +enum { + DACG = BIT(6), + DACKTST = BIT(5), + DEDGEB = BIT(4), + SYO = BIT(3), + DRI_IT_LVDS = GENMASK(2, 1), + DISPON = BIT(0), +}; + +/* Page 1, Register 0x0c */ +enum { + DRI_PLL_CP = GENMASK(7, 6), + DRI_PLL_DIVSEL = BIT(5), + DRI_PLL_N1_1 = BIT(4), + DRI_PLL_N1_0 = BIT(3), + DRI_PLL_N3_1 = BIT(2), + DRI_PLL_N3_0 = BIT(1), + DRI_PLL_CKTSTEN = BIT(0), +}; + +/* Page 1, Register 0x6b */ +enum { + VCO3CS = GENMASK(7, 6), + ICPGBK2_0 = GENMASK(5, 3), + DRI_VCO357SC = BIT(2), + PDPLL2 = BIT(1), + DRI_PD_SER = BIT(0), +}; + +/* Page 1, Register 0x6c */ +enum { + PLL2N11 = GENMASK(7, 4), + PLL2N5_4 = BIT(3), + PLL2N5_TOP = BIT(2), + DRI_PLL_PD = BIT(1), + PD_I2CM = BIT(0), +}; + +/* Page 3, Register 0x28 */ +enum { + DIFF_EN = GENMASK(7, 6), + CORREC_EN = GENMASK(5, 4), + VGACLK_BP = BIT(3), + HM_LV_SEL = BIT(2), + HD_VGA_SEL = BIT(1), +}; + +/* Page 3, Register 0x2a */ +enum { + LVDSCLK_BP = BIT(7), + HDTVCLK_BP = BIT(6), + HDMICLK_BP = BIT(5), + HDTV_BP = BIT(4), + HDMI_BP = BIT(3), + THRWL = GENMASK(2, 0), +}; + +/* Page 4, Register 0x52 */ +enum { + PGM_ARSTB = BIT(7), + MCU_ARSTB = BIT(6), + MCU_RETB = BIT(2), + RESETIB = BIT(1), + RESETDB = BIT(0), +}; + +struct ch7033_priv { + struct regmap *regmap; + struct drm_bridge *next_bridge; + struct drm_encoder encoder; + struct drm_bridge bridge; + struct drm_connector connector; +}; + +#define conn_to_ch7033_priv(x) \ + container_of(x, struct ch7033_priv, connector) +#define bridge_to_ch7033_priv(x) \ + container_of(x, struct ch7033_priv, bridge) + + +static enum drm_connector_status ch7033_connector_detect( + struct drm_connector *connector, bool force) +{ + struct ch7033_priv *priv = conn_to_ch7033_priv(connector); + + return drm_bridge_detect(priv->next_bridge); +} + +static const struct drm_connector_funcs ch7033_connector_funcs = { + .reset = drm_atomic_helper_connector_reset, + .fill_modes = drm_helper_probe_single_connector_modes, + .detect = ch7033_connector_detect, + .destroy = drm_connector_cleanup, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +static int ch7033_connector_get_modes(struct drm_connector *connector) +{ + struct ch7033_priv *priv = conn_to_ch7033_priv(connector); + struct edid *edid; + int ret; + + edid = drm_bridge_get_edid(priv->next_bridge, connector); + drm_connector_update_edid_property(connector, edid); + if (edid) { + ret = drm_add_edid_modes(connector, edid); + kfree(edid); + } else { + ret = drm_add_modes_noedid(connector, 1920, 1080); + drm_set_preferred_mode(connector, 1024, 768); + } + + return ret; +} + +static struct drm_encoder *ch7033_connector_best_encoder( + struct drm_connector *connector) +{ + struct ch7033_priv *priv = conn_to_ch7033_priv(connector); + + return priv->bridge.encoder; +} + +static const struct drm_connector_helper_funcs ch7033_connector_helper_funcs = { + .get_modes = ch7033_connector_get_modes, + .best_encoder = ch7033_connector_best_encoder, +}; + +static void ch7033_hpd_event(void *arg, enum drm_connector_status status) +{ + struct ch7033_priv *priv = arg; + + if (priv->bridge.dev) + drm_helper_hpd_irq_event(priv->connector.dev); +} + +static int ch7033_bridge_attach(struct drm_bridge *bridge, + enum drm_bridge_attach_flags flags) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + struct drm_connector *connector = &priv->connector; + int ret; + + ret = drm_bridge_attach(bridge->encoder, priv->next_bridge, bridge, + DRM_BRIDGE_ATTACH_NO_CONNECTOR); + if (ret < 0) + return ret; + + if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) + return 0; + + if (priv->next_bridge->ops & DRM_BRIDGE_OP_DETECT) { + connector->polled = DRM_CONNECTOR_POLL_HPD; + } else { + connector->polled = DRM_CONNECTOR_POLL_CONNECT | + DRM_CONNECTOR_POLL_DISCONNECT; + } + + if (priv->next_bridge->ops & DRM_BRIDGE_OP_HPD) { + drm_bridge_hpd_enable(priv->next_bridge, ch7033_hpd_event, + priv); + } + + drm_connector_helper_add(connector, + &ch7033_connector_helper_funcs); + ret = drm_connector_init_with_ddc(bridge->dev, &priv->connector, + &ch7033_connector_funcs, + priv->next_bridge->type, + priv->next_bridge->ddc); + if (ret) { + DRM_ERROR("Failed to initialize connector\n"); + return ret; + } + + drm_connector_attach_encoder(&priv->connector, bridge->encoder); + return 0; +} + +static void ch7033_bridge_detach(struct drm_bridge *bridge) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + + if (priv->next_bridge->ops & DRM_BRIDGE_OP_HPD) + drm_bridge_hpd_disable(priv->next_bridge); + drm_connector_cleanup(&priv->connector); +} + +static enum drm_mode_status ch7033_bridge_mode_valid(struct drm_bridge *bridge, + const struct drm_display_mode *mode) +{ + if (mode->clock > 165000) + return MODE_CLOCK_HIGH; + if (mode->hdisplay >= 1920) + return MODE_BAD_HVALUE; + if (mode->vdisplay >= 1080) + return MODE_BAD_VVALUE; + return MODE_OK; +} + +static void ch7033_bridge_disable(struct drm_bridge *bridge) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + + regmap_write(priv->regmap, 0x03, 0x04); + regmap_update_bits(priv->regmap, 0x52, RESETDB, 0x00); +} + +static void ch7033_bridge_enable(struct drm_bridge *bridge) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + + regmap_write(priv->regmap, 0x03, 0x04); + regmap_update_bits(priv->regmap, 0x52, RESETDB, RESETDB); +} + +static void ch7033_bridge_mode_set(struct drm_bridge *bridge, + const struct drm_display_mode *mode, + const struct drm_display_mode *adjusted_mode) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + int hbporch = mode->hsync_start - mode->hdisplay; + int hsynclen = mode->hsync_end - mode->hsync_start; + int vbporch = mode->vsync_start - mode->vdisplay; + int vsynclen = mode->vsync_end - mode->vsync_start; + + /* + * Page 4 + */ + regmap_write(priv->regmap, 0x03, 0x04); + + /* Turn everything off to set all the registers to their defaults. */ + regmap_write(priv->regmap, 0x52, 0x00); + /* Bring I/O block up. */ + regmap_write(priv->regmap, 0x52, RESETIB); + + /* + * Page 0 + */ + regmap_write(priv->regmap, 0x03, 0x00); + + /* Bring up parts we need from the power down. */ + regmap_update_bits(priv->regmap, 0x07, DRI_PD | IO_PD, 0); + regmap_update_bits(priv->regmap, 0x08, DRI_PDDRI | PDDAC | PANEN, 0); + regmap_update_bits(priv->regmap, 0x09, DPD | GCKOFF | + HDMI_PD | VGA_PD, 0); + regmap_update_bits(priv->regmap, 0x0a, HD_DVIB, 0); + + /* Horizontal input timing. */ + regmap_write(priv->regmap, 0x0b, (mode->htotal >> 8) << 3 | + (mode->hdisplay >> 8)); + regmap_write(priv->regmap, 0x0c, mode->hdisplay); + regmap_write(priv->regmap, 0x0d, mode->htotal); + regmap_write(priv->regmap, 0x0e, (hsynclen >> 8) << 3 | + (hbporch >> 8)); + regmap_write(priv->regmap, 0x0f, hbporch); + regmap_write(priv->regmap, 0x10, hsynclen); + + /* Vertical input timing. */ + regmap_write(priv->regmap, 0x11, (mode->vtotal >> 8) << 3 | + (mode->vdisplay >> 8)); + regmap_write(priv->regmap, 0x12, mode->vdisplay); + regmap_write(priv->regmap, 0x13, mode->vtotal); + regmap_write(priv->regmap, 0x14, ((vsynclen >> 8) << 3) | + (vbporch >> 8)); + regmap_write(priv->regmap, 0x15, vbporch); + regmap_write(priv->regmap, 0x16, vsynclen); + + /* Input color swap. */ + regmap_update_bits(priv->regmap, 0x18, SWAP, BYTE_SWAP_BGR); + + /* Input clock and sync polarity. */ + regmap_update_bits(priv->regmap, 0x19, 0x1, mode->clock >> 16); + regmap_update_bits(priv->regmap, 0x19, HPO_I | VPO_I | GCLKFREQ, + (mode->flags & DRM_MODE_FLAG_PHSYNC) ? HPO_I : 0 | + (mode->flags & DRM_MODE_FLAG_PVSYNC) ? VPO_I : 0 | + mode->clock >> 16); + regmap_write(priv->regmap, 0x1a, mode->clock >> 8); + regmap_write(priv->regmap, 0x1b, mode->clock); + + /* Horizontal output timing. */ + regmap_write(priv->regmap, 0x1f, (mode->htotal >> 8) << 3 | + (mode->hdisplay >> 8)); + regmap_write(priv->regmap, 0x20, mode->hdisplay); + regmap_write(priv->regmap, 0x21, mode->htotal); + + /* Vertical output timing. */ + regmap_write(priv->regmap, 0x25, (mode->vtotal >> 8) << 3 | + (mode->vdisplay >> 8)); + regmap_write(priv->regmap, 0x26, mode->vdisplay); + regmap_write(priv->regmap, 0x27, mode->vtotal); + + /* VGA channel bypass */ + regmap_update_bits(priv->regmap, 0x2b, VFMT, 9); + + /* Output sync polarity. */ + regmap_update_bits(priv->regmap, 0x2e, HPO_O | VPO_O, + (mode->flags & DRM_MODE_FLAG_PHSYNC) ? HPO_O : 0 | + (mode->flags & DRM_MODE_FLAG_PVSYNC) ? VPO_O : 0); + + /* HDMI horizontal output timing. */ + regmap_update_bits(priv->regmap, 0x54, HWO_HDMI_HI | HOO_HDMI_HI, + (hsynclen >> 8) << 3 | + (hbporch >> 8)); + regmap_write(priv->regmap, 0x55, hbporch); + regmap_write(priv->regmap, 0x56, hsynclen); + + /* HDMI vertical output timing. */ + regmap_update_bits(priv->regmap, 0x57, VWO_HDMI_HI | VOO_HDMI_HI, + (vsynclen >> 8) << 3 | + (vbporch >> 8)); + regmap_write(priv->regmap, 0x58, vbporch); + regmap_write(priv->regmap, 0x59, vsynclen); + + /* Pick HDMI, not LVDS. */ + regmap_update_bits(priv->regmap, 0x7e, HDMI_LVDS_SEL, HDMI_LVDS_SEL); + + /* + * Page 1 + */ + regmap_write(priv->regmap, 0x03, 0x01); + + /* No idea what these do, but VGA is wobbly and blinky without them. */ + regmap_update_bits(priv->regmap, 0x07, CKINV, CKINV); + regmap_update_bits(priv->regmap, 0x08, DISPON, DISPON); + + /* DRI PLL */ + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_DIVSEL, DRI_PLL_DIVSEL); + if (mode->clock <= 40000) { + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_N1_1 | + DRI_PLL_N1_0 | + DRI_PLL_N3_1 | + DRI_PLL_N3_0, + 0); + } else if (mode->clock < 80000) { + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_N1_1 | + DRI_PLL_N1_0 | + DRI_PLL_N3_1 | + DRI_PLL_N3_0, + DRI_PLL_N3_0 | + DRI_PLL_N1_0); + } else { + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_N1_1 | + DRI_PLL_N1_0 | + DRI_PLL_N3_1 | + DRI_PLL_N3_0, + DRI_PLL_N3_1 | + DRI_PLL_N1_1); + } + + /* This seems to be color calibration for VGA. */ + regmap_write(priv->regmap, 0x64, 0x29); /* LSB Blue */ + regmap_write(priv->regmap, 0x65, 0x29); /* LSB Green */ + regmap_write(priv->regmap, 0x66, 0x29); /* LSB Red */ + regmap_write(priv->regmap, 0x67, 0x00); /* MSB Blue */ + regmap_write(priv->regmap, 0x68, 0x00); /* MSB Green */ + regmap_write(priv->regmap, 0x69, 0x00); /* MSB Red */ + + regmap_update_bits(priv->regmap, 0x6b, DRI_PD_SER, 0x00); + regmap_update_bits(priv->regmap, 0x6c, DRI_PLL_PD, 0x00); + + /* + * Page 3 + */ + regmap_write(priv->regmap, 0x03, 0x03); + + /* More bypasses and apparently another HDMI/LVDS selector. */ + regmap_update_bits(priv->regmap, 0x28, VGACLK_BP | HM_LV_SEL, + VGACLK_BP | HM_LV_SEL); + regmap_update_bits(priv->regmap, 0x2a, HDMICLK_BP | HDMI_BP, + HDMICLK_BP | HDMI_BP); + + /* + * Page 4 + */ + regmap_write(priv->regmap, 0x03, 0x04); + + /* Output clock. */ + regmap_write(priv->regmap, 0x10, mode->clock >> 16); + regmap_write(priv->regmap, 0x11, mode->clock >> 8); + regmap_write(priv->regmap, 0x12, mode->clock); +} + +static const struct drm_bridge_funcs ch7033_bridge_funcs = { + .attach = ch7033_bridge_attach, + .detach = ch7033_bridge_detach, + .mode_valid = ch7033_bridge_mode_valid, + .disable = ch7033_bridge_disable, + .enable = ch7033_bridge_enable, + .mode_set = ch7033_bridge_mode_set, +}; + +static void ch7033_encoder_destroy(struct drm_encoder *encoder) +{ + drm_encoder_cleanup(encoder); +} + +static const struct drm_encoder_funcs ch7033_encoder_funcs = { + .destroy = ch7033_encoder_destroy, +}; + +static int ch7033_bind(struct device *dev, struct device *master, + void *data) +{ + struct drm_device *drm = data; + struct ch7033_priv *priv = dev_get_drvdata(dev); + uint32_t crtcs; + int ret; + + crtcs = drm_of_find_possible_crtcs(drm, dev->of_node); + priv->encoder.possible_crtcs = crtcs; + + ret = drm_encoder_init(drm, &priv->encoder, &ch7033_encoder_funcs, + DRM_MODE_ENCODER_TMDS, NULL); + if (ret) + return ret; + + ret = drm_bridge_attach(&priv->encoder, &priv->bridge, NULL, 0); + if (ret) + drm_encoder_cleanup(&priv->encoder); + + return ret; +} + +static void ch7033_unbind(struct device *dev, struct device *master, + void *data) +{ + struct ch7033_priv *priv = dev_get_drvdata(dev); + + drm_encoder_cleanup(&priv->encoder); +} + +static const struct regmap_config ch7033_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = 0x7f, +}; + +static const struct component_ops ch7033_ops = { + .bind = ch7033_bind, + .unbind = ch7033_unbind, +}; + +static int ch7033_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct device *dev = &client->dev; + struct ch7033_priv *priv; + unsigned int val; + int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + dev_set_drvdata(dev, priv); + + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, -1, NULL, + &priv->next_bridge); + if (ret) + return ret; + + priv->regmap = devm_regmap_init_i2c(client, &ch7033_regmap_config); + if (IS_ERR(priv->regmap)) { + dev_err(&client->dev, "regmap init failed\n"); + return PTR_ERR(priv->regmap); + } + + ret = regmap_read(priv->regmap, 0x00, &val); + if (ret < 0) { + dev_err(&client->dev, "error reading the model id: %d\n", ret); + return ret; + } + if ((val & 0xf7) != 0x56) { + dev_err(&client->dev, "the device is not a ch7033\n"); + return -ENODEV; + } + + regmap_write(priv->regmap, 0x03, 0x04); + ret = regmap_read(priv->regmap, 0x51, &val); + if (ret < 0) { + dev_err(&client->dev, "error reading the model id: %d\n", ret); + return ret; + } + if ((val & 0x0f) != 3) { + dev_err(&client->dev, "unknown revision %u\n", val); + return -ENODEV; + } + + INIT_LIST_HEAD(&priv->bridge.list); + priv->bridge.funcs = &ch7033_bridge_funcs; + priv->bridge.of_node = dev->of_node; + drm_bridge_add(&priv->bridge); + + ret = component_add(dev, &ch7033_ops); + if (ret) { + drm_bridge_remove(&priv->bridge); + return ret; + } + + dev_info(dev, "Chrontel CH7033 Video Encoder\n"); + return 0; +} + +static int ch7033_remove(struct i2c_client *client) +{ + struct device *dev = &client->dev; + struct ch7033_priv *priv = dev_get_drvdata(dev); + + component_del(dev, &ch7033_ops); + drm_bridge_remove(&priv->bridge); + + return 0; +} + +static const struct of_device_id ch7033_dt_ids[] = { + { .compatible = "chrontel,ch7033", }, + { } +}; +MODULE_DEVICE_TABLE(of, ch7033_dt_ids); + +static const struct i2c_device_id ch7033_ids[] = { + { "ch7033", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ch7033_ids); + +static struct i2c_driver ch7033_driver = { + .probe = ch7033_probe, + .remove = ch7033_remove, + .driver = { + .name = "ch7033", + .of_match_table = of_match_ptr(ch7033_dt_ids), + }, + .id_table = ch7033_ids, +}; + +module_i2c_driver(ch7033_driver); + +MODULE_AUTHOR("Lubomir Rintel <lkundrak@v3.sk>"); +MODULE_DESCRIPTION("Chrontel CH7033 Video Encoder Driver"); +MODULE_LICENSE("GPL v2"); -- 2.24.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 3/3] drm/bridge: chrontel-ch7033: Add a new driver @ 2020-03-07 19:08 ` Lubomir Rintel 0 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:08 UTC (permalink / raw) To: Andrzej Hajda Cc: Mark Rutland, devicetree, Jernej Skrabec, Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel, dri-devel, Lubomir Rintel, Rob Herring, Laurent Pinchart This is a driver for video encoder with VGA and DVI/HDMI outputs. There is no documentation for the chip -- the operation was guessed from what was sniffed on a Dell Wyse 3020 ThinOS terminal, the register names come from the ch7035 driver in Mediatek's GPL code dump. Only bare minimum is implemented -- no fancy stuff, such as scaling. That would only worsen our misery. We don't load the firmware and we don't need to even bother enabling the MCU. There are probably no distributable firmware images anyway. Just like the tda998x driver, this one uses the component framework and adds an encoder on component bind, so that it works with the Armada DRM driver. Tested with a handful of monitors ranging from 1024x768@75 to 1400x1050@60, with VGA as well as DVI. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> --- Changes since v1: - Sort the includes - Drop a useless model id read - Chain to the bridge-connector instead of dealing with the HPD/EDID readout machinery ourselves - Utilize regmap to access the registers drivers/gpu/drm/bridge/Kconfig | 10 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/chrontel-ch7033.c | 675 +++++++++++++++++++++++ 3 files changed, 686 insertions(+) create mode 100644 drivers/gpu/drm/bridge/chrontel-ch7033.c diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig index aaed2347ace9d..0ebc72d62a5b2 100644 --- a/drivers/gpu/drm/bridge/Kconfig +++ b/drivers/gpu/drm/bridge/Kconfig @@ -27,6 +27,16 @@ config DRM_CDNS_DSI Support Cadence DPI to DSI bridge. This is an internal bridge and is meant to be directly embedded in a SoC. +config DRM_CHRONTEL_CH7033 + tristate "Chrontel CH7033 Video Encoder" + depends on OF + select DRM_KMS_HELPER + help + Enable support for the Chrontel CH7033 VGA/DVI/HDMI Encoder, as + found in the Dell Wyse 3020 thin client. + + If in doubt, say "N". + config DRM_DISPLAY_CONNECTOR tristate "Display connector support" depends on OF diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile index 6fb062b5b0f04..a844315feddb4 100644 --- a/drivers/gpu/drm/bridge/Makefile +++ b/drivers/gpu/drm/bridge/Makefile @@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o +obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o diff --git a/drivers/gpu/drm/bridge/chrontel-ch7033.c b/drivers/gpu/drm/bridge/chrontel-ch7033.c new file mode 100644 index 0000000000000..342b2e2bd2b1c --- /dev/null +++ b/drivers/gpu/drm/bridge/chrontel-ch7033.c @@ -0,0 +1,675 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Chrontel CH7033 Video Encoder Driver + * + * Copyright (C) 2019,2020 Lubomir Rintel + */ + +#include <linux/component.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/regmap.h> + +#include <drm/drm_atomic_helper.h> +#include <drm/drm_bridge.h> +#include <drm/drm_edid.h> +#include <drm/drm_of.h> +#include <drm/drm_print.h> +#include <drm/drm_probe_helper.h> + +/* Page 0, Register 0x07 */ +enum { + DRI_PD = BIT(3), + IO_PD = BIT(5), +}; + +/* Page 0, Register 0x08 */ +enum { + DRI_PDDRI = GENMASK(7, 4), + PDDAC = GENMASK(3, 1), + PANEN = BIT(0), +}; + +/* Page 0, Register 0x09 */ +enum { + DPD = BIT(7), + GCKOFF = BIT(6), + TV_BP = BIT(5), + SCLPD = BIT(4), + SDPD = BIT(3), + VGA_PD = BIT(2), + HDBKPD = BIT(1), + HDMI_PD = BIT(0), +}; + +/* Page 0, Register 0x0a */ +enum { + MEMINIT = BIT(7), + MEMIDLE = BIT(6), + MEMPD = BIT(5), + STOP = BIT(4), + LVDS_PD = BIT(3), + HD_DVIB = BIT(2), + HDCP_PD = BIT(1), + MCU_PD = BIT(0), +}; + +/* Page 0, Register 0x18 */ +enum { + IDF = GENMASK(7, 4), + INTEN = BIT(3), + SWAP = GENMASK(2, 0), +}; + +enum { + BYTE_SWAP_RGB = 0, + BYTE_SWAP_RBG = 1, + BYTE_SWAP_GRB = 2, + BYTE_SWAP_GBR = 3, + BYTE_SWAP_BRG = 4, + BYTE_SWAP_BGR = 5, +}; + +/* Page 0, Register 0x19 */ +enum { + HPO_I = BIT(5), + VPO_I = BIT(4), + DEPO_I = BIT(3), + CRYS_EN = BIT(2), + GCLKFREQ = GENMASK(2, 0), +}; + +/* Page 0, Register 0x2e */ +enum { + HFLIP = BIT(7), + VFLIP = BIT(6), + DEPO_O = BIT(5), + HPO_O = BIT(4), + VPO_O = BIT(3), + TE = GENMASK(2, 0), +}; + +/* Page 0, Register 0x2b */ +enum { + SWAPS = GENMASK(7, 4), + VFMT = GENMASK(3, 0), +}; + +/* Page 0, Register 0x54 */ +enum { + COMP_BP = BIT(7), + DAC_EN_T = BIT(6), + HWO_HDMI_HI = GENMASK(5, 3), + HOO_HDMI_HI = GENMASK(2, 0), +}; + +/* Page 0, Register 0x57 */ +enum { + FLDSEN = BIT(7), + VWO_HDMI_HI = GENMASK(5, 3), + VOO_HDMI_HI = GENMASK(2, 0), +}; + +/* Page 0, Register 0x7e */ +enum { + HDMI_LVDS_SEL = BIT(7), + DE_GEN = BIT(6), + PWM_INDEX_HI = BIT(5), + USE_DE = BIT(4), + R_INT = GENMASK(3, 0), +}; + +/* Page 1, Register 0x07 */ +enum { + BPCKSEL = BIT(7), + DRI_CMFB_EN = BIT(6), + CEC_PUEN = BIT(5), + CEC_T = BIT(3), + CKINV = BIT(2), + CK_TVINV = BIT(1), + DRI_CKS2 = BIT(0), +}; + +/* Page 1, Register 0x08 */ +enum { + DACG = BIT(6), + DACKTST = BIT(5), + DEDGEB = BIT(4), + SYO = BIT(3), + DRI_IT_LVDS = GENMASK(2, 1), + DISPON = BIT(0), +}; + +/* Page 1, Register 0x0c */ +enum { + DRI_PLL_CP = GENMASK(7, 6), + DRI_PLL_DIVSEL = BIT(5), + DRI_PLL_N1_1 = BIT(4), + DRI_PLL_N1_0 = BIT(3), + DRI_PLL_N3_1 = BIT(2), + DRI_PLL_N3_0 = BIT(1), + DRI_PLL_CKTSTEN = BIT(0), +}; + +/* Page 1, Register 0x6b */ +enum { + VCO3CS = GENMASK(7, 6), + ICPGBK2_0 = GENMASK(5, 3), + DRI_VCO357SC = BIT(2), + PDPLL2 = BIT(1), + DRI_PD_SER = BIT(0), +}; + +/* Page 1, Register 0x6c */ +enum { + PLL2N11 = GENMASK(7, 4), + PLL2N5_4 = BIT(3), + PLL2N5_TOP = BIT(2), + DRI_PLL_PD = BIT(1), + PD_I2CM = BIT(0), +}; + +/* Page 3, Register 0x28 */ +enum { + DIFF_EN = GENMASK(7, 6), + CORREC_EN = GENMASK(5, 4), + VGACLK_BP = BIT(3), + HM_LV_SEL = BIT(2), + HD_VGA_SEL = BIT(1), +}; + +/* Page 3, Register 0x2a */ +enum { + LVDSCLK_BP = BIT(7), + HDTVCLK_BP = BIT(6), + HDMICLK_BP = BIT(5), + HDTV_BP = BIT(4), + HDMI_BP = BIT(3), + THRWL = GENMASK(2, 0), +}; + +/* Page 4, Register 0x52 */ +enum { + PGM_ARSTB = BIT(7), + MCU_ARSTB = BIT(6), + MCU_RETB = BIT(2), + RESETIB = BIT(1), + RESETDB = BIT(0), +}; + +struct ch7033_priv { + struct regmap *regmap; + struct drm_bridge *next_bridge; + struct drm_encoder encoder; + struct drm_bridge bridge; + struct drm_connector connector; +}; + +#define conn_to_ch7033_priv(x) \ + container_of(x, struct ch7033_priv, connector) +#define bridge_to_ch7033_priv(x) \ + container_of(x, struct ch7033_priv, bridge) + + +static enum drm_connector_status ch7033_connector_detect( + struct drm_connector *connector, bool force) +{ + struct ch7033_priv *priv = conn_to_ch7033_priv(connector); + + return drm_bridge_detect(priv->next_bridge); +} + +static const struct drm_connector_funcs ch7033_connector_funcs = { + .reset = drm_atomic_helper_connector_reset, + .fill_modes = drm_helper_probe_single_connector_modes, + .detect = ch7033_connector_detect, + .destroy = drm_connector_cleanup, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +static int ch7033_connector_get_modes(struct drm_connector *connector) +{ + struct ch7033_priv *priv = conn_to_ch7033_priv(connector); + struct edid *edid; + int ret; + + edid = drm_bridge_get_edid(priv->next_bridge, connector); + drm_connector_update_edid_property(connector, edid); + if (edid) { + ret = drm_add_edid_modes(connector, edid); + kfree(edid); + } else { + ret = drm_add_modes_noedid(connector, 1920, 1080); + drm_set_preferred_mode(connector, 1024, 768); + } + + return ret; +} + +static struct drm_encoder *ch7033_connector_best_encoder( + struct drm_connector *connector) +{ + struct ch7033_priv *priv = conn_to_ch7033_priv(connector); + + return priv->bridge.encoder; +} + +static const struct drm_connector_helper_funcs ch7033_connector_helper_funcs = { + .get_modes = ch7033_connector_get_modes, + .best_encoder = ch7033_connector_best_encoder, +}; + +static void ch7033_hpd_event(void *arg, enum drm_connector_status status) +{ + struct ch7033_priv *priv = arg; + + if (priv->bridge.dev) + drm_helper_hpd_irq_event(priv->connector.dev); +} + +static int ch7033_bridge_attach(struct drm_bridge *bridge, + enum drm_bridge_attach_flags flags) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + struct drm_connector *connector = &priv->connector; + int ret; + + ret = drm_bridge_attach(bridge->encoder, priv->next_bridge, bridge, + DRM_BRIDGE_ATTACH_NO_CONNECTOR); + if (ret < 0) + return ret; + + if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) + return 0; + + if (priv->next_bridge->ops & DRM_BRIDGE_OP_DETECT) { + connector->polled = DRM_CONNECTOR_POLL_HPD; + } else { + connector->polled = DRM_CONNECTOR_POLL_CONNECT | + DRM_CONNECTOR_POLL_DISCONNECT; + } + + if (priv->next_bridge->ops & DRM_BRIDGE_OP_HPD) { + drm_bridge_hpd_enable(priv->next_bridge, ch7033_hpd_event, + priv); + } + + drm_connector_helper_add(connector, + &ch7033_connector_helper_funcs); + ret = drm_connector_init_with_ddc(bridge->dev, &priv->connector, + &ch7033_connector_funcs, + priv->next_bridge->type, + priv->next_bridge->ddc); + if (ret) { + DRM_ERROR("Failed to initialize connector\n"); + return ret; + } + + drm_connector_attach_encoder(&priv->connector, bridge->encoder); + return 0; +} + +static void ch7033_bridge_detach(struct drm_bridge *bridge) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + + if (priv->next_bridge->ops & DRM_BRIDGE_OP_HPD) + drm_bridge_hpd_disable(priv->next_bridge); + drm_connector_cleanup(&priv->connector); +} + +static enum drm_mode_status ch7033_bridge_mode_valid(struct drm_bridge *bridge, + const struct drm_display_mode *mode) +{ + if (mode->clock > 165000) + return MODE_CLOCK_HIGH; + if (mode->hdisplay >= 1920) + return MODE_BAD_HVALUE; + if (mode->vdisplay >= 1080) + return MODE_BAD_VVALUE; + return MODE_OK; +} + +static void ch7033_bridge_disable(struct drm_bridge *bridge) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + + regmap_write(priv->regmap, 0x03, 0x04); + regmap_update_bits(priv->regmap, 0x52, RESETDB, 0x00); +} + +static void ch7033_bridge_enable(struct drm_bridge *bridge) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + + regmap_write(priv->regmap, 0x03, 0x04); + regmap_update_bits(priv->regmap, 0x52, RESETDB, RESETDB); +} + +static void ch7033_bridge_mode_set(struct drm_bridge *bridge, + const struct drm_display_mode *mode, + const struct drm_display_mode *adjusted_mode) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + int hbporch = mode->hsync_start - mode->hdisplay; + int hsynclen = mode->hsync_end - mode->hsync_start; + int vbporch = mode->vsync_start - mode->vdisplay; + int vsynclen = mode->vsync_end - mode->vsync_start; + + /* + * Page 4 + */ + regmap_write(priv->regmap, 0x03, 0x04); + + /* Turn everything off to set all the registers to their defaults. */ + regmap_write(priv->regmap, 0x52, 0x00); + /* Bring I/O block up. */ + regmap_write(priv->regmap, 0x52, RESETIB); + + /* + * Page 0 + */ + regmap_write(priv->regmap, 0x03, 0x00); + + /* Bring up parts we need from the power down. */ + regmap_update_bits(priv->regmap, 0x07, DRI_PD | IO_PD, 0); + regmap_update_bits(priv->regmap, 0x08, DRI_PDDRI | PDDAC | PANEN, 0); + regmap_update_bits(priv->regmap, 0x09, DPD | GCKOFF | + HDMI_PD | VGA_PD, 0); + regmap_update_bits(priv->regmap, 0x0a, HD_DVIB, 0); + + /* Horizontal input timing. */ + regmap_write(priv->regmap, 0x0b, (mode->htotal >> 8) << 3 | + (mode->hdisplay >> 8)); + regmap_write(priv->regmap, 0x0c, mode->hdisplay); + regmap_write(priv->regmap, 0x0d, mode->htotal); + regmap_write(priv->regmap, 0x0e, (hsynclen >> 8) << 3 | + (hbporch >> 8)); + regmap_write(priv->regmap, 0x0f, hbporch); + regmap_write(priv->regmap, 0x10, hsynclen); + + /* Vertical input timing. */ + regmap_write(priv->regmap, 0x11, (mode->vtotal >> 8) << 3 | + (mode->vdisplay >> 8)); + regmap_write(priv->regmap, 0x12, mode->vdisplay); + regmap_write(priv->regmap, 0x13, mode->vtotal); + regmap_write(priv->regmap, 0x14, ((vsynclen >> 8) << 3) | + (vbporch >> 8)); + regmap_write(priv->regmap, 0x15, vbporch); + regmap_write(priv->regmap, 0x16, vsynclen); + + /* Input color swap. */ + regmap_update_bits(priv->regmap, 0x18, SWAP, BYTE_SWAP_BGR); + + /* Input clock and sync polarity. */ + regmap_update_bits(priv->regmap, 0x19, 0x1, mode->clock >> 16); + regmap_update_bits(priv->regmap, 0x19, HPO_I | VPO_I | GCLKFREQ, + (mode->flags & DRM_MODE_FLAG_PHSYNC) ? HPO_I : 0 | + (mode->flags & DRM_MODE_FLAG_PVSYNC) ? VPO_I : 0 | + mode->clock >> 16); + regmap_write(priv->regmap, 0x1a, mode->clock >> 8); + regmap_write(priv->regmap, 0x1b, mode->clock); + + /* Horizontal output timing. */ + regmap_write(priv->regmap, 0x1f, (mode->htotal >> 8) << 3 | + (mode->hdisplay >> 8)); + regmap_write(priv->regmap, 0x20, mode->hdisplay); + regmap_write(priv->regmap, 0x21, mode->htotal); + + /* Vertical output timing. */ + regmap_write(priv->regmap, 0x25, (mode->vtotal >> 8) << 3 | + (mode->vdisplay >> 8)); + regmap_write(priv->regmap, 0x26, mode->vdisplay); + regmap_write(priv->regmap, 0x27, mode->vtotal); + + /* VGA channel bypass */ + regmap_update_bits(priv->regmap, 0x2b, VFMT, 9); + + /* Output sync polarity. */ + regmap_update_bits(priv->regmap, 0x2e, HPO_O | VPO_O, + (mode->flags & DRM_MODE_FLAG_PHSYNC) ? HPO_O : 0 | + (mode->flags & DRM_MODE_FLAG_PVSYNC) ? VPO_O : 0); + + /* HDMI horizontal output timing. */ + regmap_update_bits(priv->regmap, 0x54, HWO_HDMI_HI | HOO_HDMI_HI, + (hsynclen >> 8) << 3 | + (hbporch >> 8)); + regmap_write(priv->regmap, 0x55, hbporch); + regmap_write(priv->regmap, 0x56, hsynclen); + + /* HDMI vertical output timing. */ + regmap_update_bits(priv->regmap, 0x57, VWO_HDMI_HI | VOO_HDMI_HI, + (vsynclen >> 8) << 3 | + (vbporch >> 8)); + regmap_write(priv->regmap, 0x58, vbporch); + regmap_write(priv->regmap, 0x59, vsynclen); + + /* Pick HDMI, not LVDS. */ + regmap_update_bits(priv->regmap, 0x7e, HDMI_LVDS_SEL, HDMI_LVDS_SEL); + + /* + * Page 1 + */ + regmap_write(priv->regmap, 0x03, 0x01); + + /* No idea what these do, but VGA is wobbly and blinky without them. */ + regmap_update_bits(priv->regmap, 0x07, CKINV, CKINV); + regmap_update_bits(priv->regmap, 0x08, DISPON, DISPON); + + /* DRI PLL */ + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_DIVSEL, DRI_PLL_DIVSEL); + if (mode->clock <= 40000) { + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_N1_1 | + DRI_PLL_N1_0 | + DRI_PLL_N3_1 | + DRI_PLL_N3_0, + 0); + } else if (mode->clock < 80000) { + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_N1_1 | + DRI_PLL_N1_0 | + DRI_PLL_N3_1 | + DRI_PLL_N3_0, + DRI_PLL_N3_0 | + DRI_PLL_N1_0); + } else { + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_N1_1 | + DRI_PLL_N1_0 | + DRI_PLL_N3_1 | + DRI_PLL_N3_0, + DRI_PLL_N3_1 | + DRI_PLL_N1_1); + } + + /* This seems to be color calibration for VGA. */ + regmap_write(priv->regmap, 0x64, 0x29); /* LSB Blue */ + regmap_write(priv->regmap, 0x65, 0x29); /* LSB Green */ + regmap_write(priv->regmap, 0x66, 0x29); /* LSB Red */ + regmap_write(priv->regmap, 0x67, 0x00); /* MSB Blue */ + regmap_write(priv->regmap, 0x68, 0x00); /* MSB Green */ + regmap_write(priv->regmap, 0x69, 0x00); /* MSB Red */ + + regmap_update_bits(priv->regmap, 0x6b, DRI_PD_SER, 0x00); + regmap_update_bits(priv->regmap, 0x6c, DRI_PLL_PD, 0x00); + + /* + * Page 3 + */ + regmap_write(priv->regmap, 0x03, 0x03); + + /* More bypasses and apparently another HDMI/LVDS selector. */ + regmap_update_bits(priv->regmap, 0x28, VGACLK_BP | HM_LV_SEL, + VGACLK_BP | HM_LV_SEL); + regmap_update_bits(priv->regmap, 0x2a, HDMICLK_BP | HDMI_BP, + HDMICLK_BP | HDMI_BP); + + /* + * Page 4 + */ + regmap_write(priv->regmap, 0x03, 0x04); + + /* Output clock. */ + regmap_write(priv->regmap, 0x10, mode->clock >> 16); + regmap_write(priv->regmap, 0x11, mode->clock >> 8); + regmap_write(priv->regmap, 0x12, mode->clock); +} + +static const struct drm_bridge_funcs ch7033_bridge_funcs = { + .attach = ch7033_bridge_attach, + .detach = ch7033_bridge_detach, + .mode_valid = ch7033_bridge_mode_valid, + .disable = ch7033_bridge_disable, + .enable = ch7033_bridge_enable, + .mode_set = ch7033_bridge_mode_set, +}; + +static void ch7033_encoder_destroy(struct drm_encoder *encoder) +{ + drm_encoder_cleanup(encoder); +} + +static const struct drm_encoder_funcs ch7033_encoder_funcs = { + .destroy = ch7033_encoder_destroy, +}; + +static int ch7033_bind(struct device *dev, struct device *master, + void *data) +{ + struct drm_device *drm = data; + struct ch7033_priv *priv = dev_get_drvdata(dev); + uint32_t crtcs; + int ret; + + crtcs = drm_of_find_possible_crtcs(drm, dev->of_node); + priv->encoder.possible_crtcs = crtcs; + + ret = drm_encoder_init(drm, &priv->encoder, &ch7033_encoder_funcs, + DRM_MODE_ENCODER_TMDS, NULL); + if (ret) + return ret; + + ret = drm_bridge_attach(&priv->encoder, &priv->bridge, NULL, 0); + if (ret) + drm_encoder_cleanup(&priv->encoder); + + return ret; +} + +static void ch7033_unbind(struct device *dev, struct device *master, + void *data) +{ + struct ch7033_priv *priv = dev_get_drvdata(dev); + + drm_encoder_cleanup(&priv->encoder); +} + +static const struct regmap_config ch7033_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = 0x7f, +}; + +static const struct component_ops ch7033_ops = { + .bind = ch7033_bind, + .unbind = ch7033_unbind, +}; + +static int ch7033_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct device *dev = &client->dev; + struct ch7033_priv *priv; + unsigned int val; + int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + dev_set_drvdata(dev, priv); + + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, -1, NULL, + &priv->next_bridge); + if (ret) + return ret; + + priv->regmap = devm_regmap_init_i2c(client, &ch7033_regmap_config); + if (IS_ERR(priv->regmap)) { + dev_err(&client->dev, "regmap init failed\n"); + return PTR_ERR(priv->regmap); + } + + ret = regmap_read(priv->regmap, 0x00, &val); + if (ret < 0) { + dev_err(&client->dev, "error reading the model id: %d\n", ret); + return ret; + } + if ((val & 0xf7) != 0x56) { + dev_err(&client->dev, "the device is not a ch7033\n"); + return -ENODEV; + } + + regmap_write(priv->regmap, 0x03, 0x04); + ret = regmap_read(priv->regmap, 0x51, &val); + if (ret < 0) { + dev_err(&client->dev, "error reading the model id: %d\n", ret); + return ret; + } + if ((val & 0x0f) != 3) { + dev_err(&client->dev, "unknown revision %u\n", val); + return -ENODEV; + } + + INIT_LIST_HEAD(&priv->bridge.list); + priv->bridge.funcs = &ch7033_bridge_funcs; + priv->bridge.of_node = dev->of_node; + drm_bridge_add(&priv->bridge); + + ret = component_add(dev, &ch7033_ops); + if (ret) { + drm_bridge_remove(&priv->bridge); + return ret; + } + + dev_info(dev, "Chrontel CH7033 Video Encoder\n"); + return 0; +} + +static int ch7033_remove(struct i2c_client *client) +{ + struct device *dev = &client->dev; + struct ch7033_priv *priv = dev_get_drvdata(dev); + + component_del(dev, &ch7033_ops); + drm_bridge_remove(&priv->bridge); + + return 0; +} + +static const struct of_device_id ch7033_dt_ids[] = { + { .compatible = "chrontel,ch7033", }, + { } +}; +MODULE_DEVICE_TABLE(of, ch7033_dt_ids); + +static const struct i2c_device_id ch7033_ids[] = { + { "ch7033", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ch7033_ids); + +static struct i2c_driver ch7033_driver = { + .probe = ch7033_probe, + .remove = ch7033_remove, + .driver = { + .name = "ch7033", + .of_match_table = of_match_ptr(ch7033_dt_ids), + }, + .id_table = ch7033_ids, +}; + +module_i2c_driver(ch7033_driver); + +MODULE_AUTHOR("Lubomir Rintel <lkundrak@v3.sk>"); +MODULE_DESCRIPTION("Chrontel CH7033 Video Encoder Driver"); +MODULE_LICENSE("GPL v2"); -- 2.24.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RESEND PATCH v2 3/3] drm/bridge: chrontel-ch7033: Add a new driver @ 2020-03-07 19:08 ` Lubomir Rintel 0 siblings, 0 replies; 12+ messages in thread From: Lubomir Rintel @ 2020-03-07 19:08 UTC (permalink / raw) To: Andrzej Hajda Cc: Mark Rutland, devicetree, Jernej Skrabec, Jonas Karlman, David Airlie, Neil Armstrong, linux-kernel, dri-devel, Lubomir Rintel, Rob Herring, Laurent Pinchart This is a driver for video encoder with VGA and DVI/HDMI outputs. There is no documentation for the chip -- the operation was guessed from what was sniffed on a Dell Wyse 3020 ThinOS terminal, the register names come from the ch7035 driver in Mediatek's GPL code dump. Only bare minimum is implemented -- no fancy stuff, such as scaling. That would only worsen our misery. We don't load the firmware and we don't need to even bother enabling the MCU. There are probably no distributable firmware images anyway. Just like the tda998x driver, this one uses the component framework and adds an encoder on component bind, so that it works with the Armada DRM driver. Tested with a handful of monitors ranging from 1024x768@75 to 1400x1050@60, with VGA as well as DVI. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> --- Changes since v1: - Sort the includes - Drop a useless model id read - Chain to the bridge-connector instead of dealing with the HPD/EDID readout machinery ourselves - Utilize regmap to access the registers drivers/gpu/drm/bridge/Kconfig | 10 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/chrontel-ch7033.c | 675 +++++++++++++++++++++++ 3 files changed, 686 insertions(+) create mode 100644 drivers/gpu/drm/bridge/chrontel-ch7033.c diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig index aaed2347ace9d..0ebc72d62a5b2 100644 --- a/drivers/gpu/drm/bridge/Kconfig +++ b/drivers/gpu/drm/bridge/Kconfig @@ -27,6 +27,16 @@ config DRM_CDNS_DSI Support Cadence DPI to DSI bridge. This is an internal bridge and is meant to be directly embedded in a SoC. +config DRM_CHRONTEL_CH7033 + tristate "Chrontel CH7033 Video Encoder" + depends on OF + select DRM_KMS_HELPER + help + Enable support for the Chrontel CH7033 VGA/DVI/HDMI Encoder, as + found in the Dell Wyse 3020 thin client. + + If in doubt, say "N". + config DRM_DISPLAY_CONNECTOR tristate "Display connector support" depends on OF diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile index 6fb062b5b0f04..a844315feddb4 100644 --- a/drivers/gpu/drm/bridge/Makefile +++ b/drivers/gpu/drm/bridge/Makefile @@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o +obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o diff --git a/drivers/gpu/drm/bridge/chrontel-ch7033.c b/drivers/gpu/drm/bridge/chrontel-ch7033.c new file mode 100644 index 0000000000000..342b2e2bd2b1c --- /dev/null +++ b/drivers/gpu/drm/bridge/chrontel-ch7033.c @@ -0,0 +1,675 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Chrontel CH7033 Video Encoder Driver + * + * Copyright (C) 2019,2020 Lubomir Rintel + */ + +#include <linux/component.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/regmap.h> + +#include <drm/drm_atomic_helper.h> +#include <drm/drm_bridge.h> +#include <drm/drm_edid.h> +#include <drm/drm_of.h> +#include <drm/drm_print.h> +#include <drm/drm_probe_helper.h> + +/* Page 0, Register 0x07 */ +enum { + DRI_PD = BIT(3), + IO_PD = BIT(5), +}; + +/* Page 0, Register 0x08 */ +enum { + DRI_PDDRI = GENMASK(7, 4), + PDDAC = GENMASK(3, 1), + PANEN = BIT(0), +}; + +/* Page 0, Register 0x09 */ +enum { + DPD = BIT(7), + GCKOFF = BIT(6), + TV_BP = BIT(5), + SCLPD = BIT(4), + SDPD = BIT(3), + VGA_PD = BIT(2), + HDBKPD = BIT(1), + HDMI_PD = BIT(0), +}; + +/* Page 0, Register 0x0a */ +enum { + MEMINIT = BIT(7), + MEMIDLE = BIT(6), + MEMPD = BIT(5), + STOP = BIT(4), + LVDS_PD = BIT(3), + HD_DVIB = BIT(2), + HDCP_PD = BIT(1), + MCU_PD = BIT(0), +}; + +/* Page 0, Register 0x18 */ +enum { + IDF = GENMASK(7, 4), + INTEN = BIT(3), + SWAP = GENMASK(2, 0), +}; + +enum { + BYTE_SWAP_RGB = 0, + BYTE_SWAP_RBG = 1, + BYTE_SWAP_GRB = 2, + BYTE_SWAP_GBR = 3, + BYTE_SWAP_BRG = 4, + BYTE_SWAP_BGR = 5, +}; + +/* Page 0, Register 0x19 */ +enum { + HPO_I = BIT(5), + VPO_I = BIT(4), + DEPO_I = BIT(3), + CRYS_EN = BIT(2), + GCLKFREQ = GENMASK(2, 0), +}; + +/* Page 0, Register 0x2e */ +enum { + HFLIP = BIT(7), + VFLIP = BIT(6), + DEPO_O = BIT(5), + HPO_O = BIT(4), + VPO_O = BIT(3), + TE = GENMASK(2, 0), +}; + +/* Page 0, Register 0x2b */ +enum { + SWAPS = GENMASK(7, 4), + VFMT = GENMASK(3, 0), +}; + +/* Page 0, Register 0x54 */ +enum { + COMP_BP = BIT(7), + DAC_EN_T = BIT(6), + HWO_HDMI_HI = GENMASK(5, 3), + HOO_HDMI_HI = GENMASK(2, 0), +}; + +/* Page 0, Register 0x57 */ +enum { + FLDSEN = BIT(7), + VWO_HDMI_HI = GENMASK(5, 3), + VOO_HDMI_HI = GENMASK(2, 0), +}; + +/* Page 0, Register 0x7e */ +enum { + HDMI_LVDS_SEL = BIT(7), + DE_GEN = BIT(6), + PWM_INDEX_HI = BIT(5), + USE_DE = BIT(4), + R_INT = GENMASK(3, 0), +}; + +/* Page 1, Register 0x07 */ +enum { + BPCKSEL = BIT(7), + DRI_CMFB_EN = BIT(6), + CEC_PUEN = BIT(5), + CEC_T = BIT(3), + CKINV = BIT(2), + CK_TVINV = BIT(1), + DRI_CKS2 = BIT(0), +}; + +/* Page 1, Register 0x08 */ +enum { + DACG = BIT(6), + DACKTST = BIT(5), + DEDGEB = BIT(4), + SYO = BIT(3), + DRI_IT_LVDS = GENMASK(2, 1), + DISPON = BIT(0), +}; + +/* Page 1, Register 0x0c */ +enum { + DRI_PLL_CP = GENMASK(7, 6), + DRI_PLL_DIVSEL = BIT(5), + DRI_PLL_N1_1 = BIT(4), + DRI_PLL_N1_0 = BIT(3), + DRI_PLL_N3_1 = BIT(2), + DRI_PLL_N3_0 = BIT(1), + DRI_PLL_CKTSTEN = BIT(0), +}; + +/* Page 1, Register 0x6b */ +enum { + VCO3CS = GENMASK(7, 6), + ICPGBK2_0 = GENMASK(5, 3), + DRI_VCO357SC = BIT(2), + PDPLL2 = BIT(1), + DRI_PD_SER = BIT(0), +}; + +/* Page 1, Register 0x6c */ +enum { + PLL2N11 = GENMASK(7, 4), + PLL2N5_4 = BIT(3), + PLL2N5_TOP = BIT(2), + DRI_PLL_PD = BIT(1), + PD_I2CM = BIT(0), +}; + +/* Page 3, Register 0x28 */ +enum { + DIFF_EN = GENMASK(7, 6), + CORREC_EN = GENMASK(5, 4), + VGACLK_BP = BIT(3), + HM_LV_SEL = BIT(2), + HD_VGA_SEL = BIT(1), +}; + +/* Page 3, Register 0x2a */ +enum { + LVDSCLK_BP = BIT(7), + HDTVCLK_BP = BIT(6), + HDMICLK_BP = BIT(5), + HDTV_BP = BIT(4), + HDMI_BP = BIT(3), + THRWL = GENMASK(2, 0), +}; + +/* Page 4, Register 0x52 */ +enum { + PGM_ARSTB = BIT(7), + MCU_ARSTB = BIT(6), + MCU_RETB = BIT(2), + RESETIB = BIT(1), + RESETDB = BIT(0), +}; + +struct ch7033_priv { + struct regmap *regmap; + struct drm_bridge *next_bridge; + struct drm_encoder encoder; + struct drm_bridge bridge; + struct drm_connector connector; +}; + +#define conn_to_ch7033_priv(x) \ + container_of(x, struct ch7033_priv, connector) +#define bridge_to_ch7033_priv(x) \ + container_of(x, struct ch7033_priv, bridge) + + +static enum drm_connector_status ch7033_connector_detect( + struct drm_connector *connector, bool force) +{ + struct ch7033_priv *priv = conn_to_ch7033_priv(connector); + + return drm_bridge_detect(priv->next_bridge); +} + +static const struct drm_connector_funcs ch7033_connector_funcs = { + .reset = drm_atomic_helper_connector_reset, + .fill_modes = drm_helper_probe_single_connector_modes, + .detect = ch7033_connector_detect, + .destroy = drm_connector_cleanup, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +static int ch7033_connector_get_modes(struct drm_connector *connector) +{ + struct ch7033_priv *priv = conn_to_ch7033_priv(connector); + struct edid *edid; + int ret; + + edid = drm_bridge_get_edid(priv->next_bridge, connector); + drm_connector_update_edid_property(connector, edid); + if (edid) { + ret = drm_add_edid_modes(connector, edid); + kfree(edid); + } else { + ret = drm_add_modes_noedid(connector, 1920, 1080); + drm_set_preferred_mode(connector, 1024, 768); + } + + return ret; +} + +static struct drm_encoder *ch7033_connector_best_encoder( + struct drm_connector *connector) +{ + struct ch7033_priv *priv = conn_to_ch7033_priv(connector); + + return priv->bridge.encoder; +} + +static const struct drm_connector_helper_funcs ch7033_connector_helper_funcs = { + .get_modes = ch7033_connector_get_modes, + .best_encoder = ch7033_connector_best_encoder, +}; + +static void ch7033_hpd_event(void *arg, enum drm_connector_status status) +{ + struct ch7033_priv *priv = arg; + + if (priv->bridge.dev) + drm_helper_hpd_irq_event(priv->connector.dev); +} + +static int ch7033_bridge_attach(struct drm_bridge *bridge, + enum drm_bridge_attach_flags flags) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + struct drm_connector *connector = &priv->connector; + int ret; + + ret = drm_bridge_attach(bridge->encoder, priv->next_bridge, bridge, + DRM_BRIDGE_ATTACH_NO_CONNECTOR); + if (ret < 0) + return ret; + + if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) + return 0; + + if (priv->next_bridge->ops & DRM_BRIDGE_OP_DETECT) { + connector->polled = DRM_CONNECTOR_POLL_HPD; + } else { + connector->polled = DRM_CONNECTOR_POLL_CONNECT | + DRM_CONNECTOR_POLL_DISCONNECT; + } + + if (priv->next_bridge->ops & DRM_BRIDGE_OP_HPD) { + drm_bridge_hpd_enable(priv->next_bridge, ch7033_hpd_event, + priv); + } + + drm_connector_helper_add(connector, + &ch7033_connector_helper_funcs); + ret = drm_connector_init_with_ddc(bridge->dev, &priv->connector, + &ch7033_connector_funcs, + priv->next_bridge->type, + priv->next_bridge->ddc); + if (ret) { + DRM_ERROR("Failed to initialize connector\n"); + return ret; + } + + drm_connector_attach_encoder(&priv->connector, bridge->encoder); + return 0; +} + +static void ch7033_bridge_detach(struct drm_bridge *bridge) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + + if (priv->next_bridge->ops & DRM_BRIDGE_OP_HPD) + drm_bridge_hpd_disable(priv->next_bridge); + drm_connector_cleanup(&priv->connector); +} + +static enum drm_mode_status ch7033_bridge_mode_valid(struct drm_bridge *bridge, + const struct drm_display_mode *mode) +{ + if (mode->clock > 165000) + return MODE_CLOCK_HIGH; + if (mode->hdisplay >= 1920) + return MODE_BAD_HVALUE; + if (mode->vdisplay >= 1080) + return MODE_BAD_VVALUE; + return MODE_OK; +} + +static void ch7033_bridge_disable(struct drm_bridge *bridge) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + + regmap_write(priv->regmap, 0x03, 0x04); + regmap_update_bits(priv->regmap, 0x52, RESETDB, 0x00); +} + +static void ch7033_bridge_enable(struct drm_bridge *bridge) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + + regmap_write(priv->regmap, 0x03, 0x04); + regmap_update_bits(priv->regmap, 0x52, RESETDB, RESETDB); +} + +static void ch7033_bridge_mode_set(struct drm_bridge *bridge, + const struct drm_display_mode *mode, + const struct drm_display_mode *adjusted_mode) +{ + struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge); + int hbporch = mode->hsync_start - mode->hdisplay; + int hsynclen = mode->hsync_end - mode->hsync_start; + int vbporch = mode->vsync_start - mode->vdisplay; + int vsynclen = mode->vsync_end - mode->vsync_start; + + /* + * Page 4 + */ + regmap_write(priv->regmap, 0x03, 0x04); + + /* Turn everything off to set all the registers to their defaults. */ + regmap_write(priv->regmap, 0x52, 0x00); + /* Bring I/O block up. */ + regmap_write(priv->regmap, 0x52, RESETIB); + + /* + * Page 0 + */ + regmap_write(priv->regmap, 0x03, 0x00); + + /* Bring up parts we need from the power down. */ + regmap_update_bits(priv->regmap, 0x07, DRI_PD | IO_PD, 0); + regmap_update_bits(priv->regmap, 0x08, DRI_PDDRI | PDDAC | PANEN, 0); + regmap_update_bits(priv->regmap, 0x09, DPD | GCKOFF | + HDMI_PD | VGA_PD, 0); + regmap_update_bits(priv->regmap, 0x0a, HD_DVIB, 0); + + /* Horizontal input timing. */ + regmap_write(priv->regmap, 0x0b, (mode->htotal >> 8) << 3 | + (mode->hdisplay >> 8)); + regmap_write(priv->regmap, 0x0c, mode->hdisplay); + regmap_write(priv->regmap, 0x0d, mode->htotal); + regmap_write(priv->regmap, 0x0e, (hsynclen >> 8) << 3 | + (hbporch >> 8)); + regmap_write(priv->regmap, 0x0f, hbporch); + regmap_write(priv->regmap, 0x10, hsynclen); + + /* Vertical input timing. */ + regmap_write(priv->regmap, 0x11, (mode->vtotal >> 8) << 3 | + (mode->vdisplay >> 8)); + regmap_write(priv->regmap, 0x12, mode->vdisplay); + regmap_write(priv->regmap, 0x13, mode->vtotal); + regmap_write(priv->regmap, 0x14, ((vsynclen >> 8) << 3) | + (vbporch >> 8)); + regmap_write(priv->regmap, 0x15, vbporch); + regmap_write(priv->regmap, 0x16, vsynclen); + + /* Input color swap. */ + regmap_update_bits(priv->regmap, 0x18, SWAP, BYTE_SWAP_BGR); + + /* Input clock and sync polarity. */ + regmap_update_bits(priv->regmap, 0x19, 0x1, mode->clock >> 16); + regmap_update_bits(priv->regmap, 0x19, HPO_I | VPO_I | GCLKFREQ, + (mode->flags & DRM_MODE_FLAG_PHSYNC) ? HPO_I : 0 | + (mode->flags & DRM_MODE_FLAG_PVSYNC) ? VPO_I : 0 | + mode->clock >> 16); + regmap_write(priv->regmap, 0x1a, mode->clock >> 8); + regmap_write(priv->regmap, 0x1b, mode->clock); + + /* Horizontal output timing. */ + regmap_write(priv->regmap, 0x1f, (mode->htotal >> 8) << 3 | + (mode->hdisplay >> 8)); + regmap_write(priv->regmap, 0x20, mode->hdisplay); + regmap_write(priv->regmap, 0x21, mode->htotal); + + /* Vertical output timing. */ + regmap_write(priv->regmap, 0x25, (mode->vtotal >> 8) << 3 | + (mode->vdisplay >> 8)); + regmap_write(priv->regmap, 0x26, mode->vdisplay); + regmap_write(priv->regmap, 0x27, mode->vtotal); + + /* VGA channel bypass */ + regmap_update_bits(priv->regmap, 0x2b, VFMT, 9); + + /* Output sync polarity. */ + regmap_update_bits(priv->regmap, 0x2e, HPO_O | VPO_O, + (mode->flags & DRM_MODE_FLAG_PHSYNC) ? HPO_O : 0 | + (mode->flags & DRM_MODE_FLAG_PVSYNC) ? VPO_O : 0); + + /* HDMI horizontal output timing. */ + regmap_update_bits(priv->regmap, 0x54, HWO_HDMI_HI | HOO_HDMI_HI, + (hsynclen >> 8) << 3 | + (hbporch >> 8)); + regmap_write(priv->regmap, 0x55, hbporch); + regmap_write(priv->regmap, 0x56, hsynclen); + + /* HDMI vertical output timing. */ + regmap_update_bits(priv->regmap, 0x57, VWO_HDMI_HI | VOO_HDMI_HI, + (vsynclen >> 8) << 3 | + (vbporch >> 8)); + regmap_write(priv->regmap, 0x58, vbporch); + regmap_write(priv->regmap, 0x59, vsynclen); + + /* Pick HDMI, not LVDS. */ + regmap_update_bits(priv->regmap, 0x7e, HDMI_LVDS_SEL, HDMI_LVDS_SEL); + + /* + * Page 1 + */ + regmap_write(priv->regmap, 0x03, 0x01); + + /* No idea what these do, but VGA is wobbly and blinky without them. */ + regmap_update_bits(priv->regmap, 0x07, CKINV, CKINV); + regmap_update_bits(priv->regmap, 0x08, DISPON, DISPON); + + /* DRI PLL */ + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_DIVSEL, DRI_PLL_DIVSEL); + if (mode->clock <= 40000) { + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_N1_1 | + DRI_PLL_N1_0 | + DRI_PLL_N3_1 | + DRI_PLL_N3_0, + 0); + } else if (mode->clock < 80000) { + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_N1_1 | + DRI_PLL_N1_0 | + DRI_PLL_N3_1 | + DRI_PLL_N3_0, + DRI_PLL_N3_0 | + DRI_PLL_N1_0); + } else { + regmap_update_bits(priv->regmap, 0x0c, DRI_PLL_N1_1 | + DRI_PLL_N1_0 | + DRI_PLL_N3_1 | + DRI_PLL_N3_0, + DRI_PLL_N3_1 | + DRI_PLL_N1_1); + } + + /* This seems to be color calibration for VGA. */ + regmap_write(priv->regmap, 0x64, 0x29); /* LSB Blue */ + regmap_write(priv->regmap, 0x65, 0x29); /* LSB Green */ + regmap_write(priv->regmap, 0x66, 0x29); /* LSB Red */ + regmap_write(priv->regmap, 0x67, 0x00); /* MSB Blue */ + regmap_write(priv->regmap, 0x68, 0x00); /* MSB Green */ + regmap_write(priv->regmap, 0x69, 0x00); /* MSB Red */ + + regmap_update_bits(priv->regmap, 0x6b, DRI_PD_SER, 0x00); + regmap_update_bits(priv->regmap, 0x6c, DRI_PLL_PD, 0x00); + + /* + * Page 3 + */ + regmap_write(priv->regmap, 0x03, 0x03); + + /* More bypasses and apparently another HDMI/LVDS selector. */ + regmap_update_bits(priv->regmap, 0x28, VGACLK_BP | HM_LV_SEL, + VGACLK_BP | HM_LV_SEL); + regmap_update_bits(priv->regmap, 0x2a, HDMICLK_BP | HDMI_BP, + HDMICLK_BP | HDMI_BP); + + /* + * Page 4 + */ + regmap_write(priv->regmap, 0x03, 0x04); + + /* Output clock. */ + regmap_write(priv->regmap, 0x10, mode->clock >> 16); + regmap_write(priv->regmap, 0x11, mode->clock >> 8); + regmap_write(priv->regmap, 0x12, mode->clock); +} + +static const struct drm_bridge_funcs ch7033_bridge_funcs = { + .attach = ch7033_bridge_attach, + .detach = ch7033_bridge_detach, + .mode_valid = ch7033_bridge_mode_valid, + .disable = ch7033_bridge_disable, + .enable = ch7033_bridge_enable, + .mode_set = ch7033_bridge_mode_set, +}; + +static void ch7033_encoder_destroy(struct drm_encoder *encoder) +{ + drm_encoder_cleanup(encoder); +} + +static const struct drm_encoder_funcs ch7033_encoder_funcs = { + .destroy = ch7033_encoder_destroy, +}; + +static int ch7033_bind(struct device *dev, struct device *master, + void *data) +{ + struct drm_device *drm = data; + struct ch7033_priv *priv = dev_get_drvdata(dev); + uint32_t crtcs; + int ret; + + crtcs = drm_of_find_possible_crtcs(drm, dev->of_node); + priv->encoder.possible_crtcs = crtcs; + + ret = drm_encoder_init(drm, &priv->encoder, &ch7033_encoder_funcs, + DRM_MODE_ENCODER_TMDS, NULL); + if (ret) + return ret; + + ret = drm_bridge_attach(&priv->encoder, &priv->bridge, NULL, 0); + if (ret) + drm_encoder_cleanup(&priv->encoder); + + return ret; +} + +static void ch7033_unbind(struct device *dev, struct device *master, + void *data) +{ + struct ch7033_priv *priv = dev_get_drvdata(dev); + + drm_encoder_cleanup(&priv->encoder); +} + +static const struct regmap_config ch7033_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = 0x7f, +}; + +static const struct component_ops ch7033_ops = { + .bind = ch7033_bind, + .unbind = ch7033_unbind, +}; + +static int ch7033_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct device *dev = &client->dev; + struct ch7033_priv *priv; + unsigned int val; + int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + dev_set_drvdata(dev, priv); + + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, -1, NULL, + &priv->next_bridge); + if (ret) + return ret; + + priv->regmap = devm_regmap_init_i2c(client, &ch7033_regmap_config); + if (IS_ERR(priv->regmap)) { + dev_err(&client->dev, "regmap init failed\n"); + return PTR_ERR(priv->regmap); + } + + ret = regmap_read(priv->regmap, 0x00, &val); + if (ret < 0) { + dev_err(&client->dev, "error reading the model id: %d\n", ret); + return ret; + } + if ((val & 0xf7) != 0x56) { + dev_err(&client->dev, "the device is not a ch7033\n"); + return -ENODEV; + } + + regmap_write(priv->regmap, 0x03, 0x04); + ret = regmap_read(priv->regmap, 0x51, &val); + if (ret < 0) { + dev_err(&client->dev, "error reading the model id: %d\n", ret); + return ret; + } + if ((val & 0x0f) != 3) { + dev_err(&client->dev, "unknown revision %u\n", val); + return -ENODEV; + } + + INIT_LIST_HEAD(&priv->bridge.list); + priv->bridge.funcs = &ch7033_bridge_funcs; + priv->bridge.of_node = dev->of_node; + drm_bridge_add(&priv->bridge); + + ret = component_add(dev, &ch7033_ops); + if (ret) { + drm_bridge_remove(&priv->bridge); + return ret; + } + + dev_info(dev, "Chrontel CH7033 Video Encoder\n"); + return 0; +} + +static int ch7033_remove(struct i2c_client *client) +{ + struct device *dev = &client->dev; + struct ch7033_priv *priv = dev_get_drvdata(dev); + + component_del(dev, &ch7033_ops); + drm_bridge_remove(&priv->bridge); + + return 0; +} + +static const struct of_device_id ch7033_dt_ids[] = { + { .compatible = "chrontel,ch7033", }, + { } +}; +MODULE_DEVICE_TABLE(of, ch7033_dt_ids); + +static const struct i2c_device_id ch7033_ids[] = { + { "ch7033", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ch7033_ids); + +static struct i2c_driver ch7033_driver = { + .probe = ch7033_probe, + .remove = ch7033_remove, + .driver = { + .name = "ch7033", + .of_match_table = of_match_ptr(ch7033_dt_ids), + }, + .id_table = ch7033_ids, +}; + +module_i2c_driver(ch7033_driver); + +MODULE_AUTHOR("Lubomir Rintel <lkundrak@v3.sk>"); +MODULE_DESCRIPTION("Chrontel CH7033 Video Encoder Driver"); +MODULE_LICENSE("GPL v2"); -- 2.24.1 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel ^ permalink raw reply related [flat|nested] 12+ messages in thread
end of thread, other threads:[~2020-03-10 8:20 UTC | newest] Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-03-07 19:07 [RESEND PATCH v2 0/3] Add support for Chrontel CH7033 VGA/DVI Encoder Lubomir Rintel 2020-03-07 19:07 ` Lubomir Rintel 2020-03-07 19:07 ` Lubomir Rintel 2020-03-07 19:07 ` [RESEND PATCH v2 1/3] dt-bindings: Add vendor prefix for Chrontel, Inc Lubomir Rintel 2020-03-07 19:07 ` Lubomir Rintel 2020-03-07 19:07 ` Lubomir Rintel 2020-03-07 19:07 ` [RESEND PATCH v2 2/3] dt-bindings: display: Add Chrontel CH7033 Video Encoder binding Lubomir Rintel 2020-03-07 19:07 ` Lubomir Rintel 2020-03-07 19:07 ` Lubomir Rintel 2020-03-07 19:08 ` [RESEND PATCH v2 3/3] drm/bridge: chrontel-ch7033: Add a new driver Lubomir Rintel 2020-03-07 19:08 ` Lubomir Rintel 2020-03-07 19:08 ` Lubomir Rintel
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.