* [PATCH] arm64: dts: renesas: r8a77961: Add thermal nodes
@ 2020-03-06 11:00 ` Geert Uytterhoeven
0 siblings, 0 replies; 6+ messages in thread
From: Geert Uytterhoeven @ 2020-03-06 11:00 UTC (permalink / raw)
To: Magnus Damm, Niklas Söderlund
Cc: linux-arm-kernel, linux-renesas-soc, linux-pm, Geert Uytterhoeven
Add a device node for the Thermal Sensor/Chip Internal Voltage Monitor
in the R-Car M3-W+ (R8A77961) SoC, and describe the thermal zones.
According to the R-Car Gen3 Hardware Manual Errata for Revision 2.00 of
Jan 31, 2020, the thermal parameters for R-Car M3-W+ are the same as for
R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
It's a bit cold in Magnus' lab:
/ # grep . /sys/devices/virtual/thermal/thermal_zone?/temp
/sys/devices/virtual/thermal/thermal_zone0/temp:17000
/sys/devices/virtual/thermal/thermal_zone1/temp:19000
/sys/devices/virtual/thermal/thermal_zone2/temp:18000
---
arch/arm64/boot/dts/renesas/r8a77961.dtsi | 80 +++++++++++++++++++++++
1 file changed, 80 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
index b6915319a61c8bf0..2f016458f57d3a33 100644
--- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
@@ -474,6 +474,20 @@
#power-domain-cells = <1>;
};
+ tsc: thermal@e6198000 {
+ compatible = "renesas,r8a77961-thermal";
+ reg = <0 0xe6198000 0 0x100>,
+ <0 0xe61a0000 0 0x100>,
+ <0 0xe61a8000 0 0x100>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 522>;
+ power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
+ resets = <&cpg 522>;
+ #thermal-sensor-cells = <1>;
+ };
+
intc_ex: interrupt-controller@e61c0000 {
#interrupt-cells = <2>;
interrupt-controller;
@@ -785,6 +799,7 @@
status = "disabled";
};
+
pwm1: pwm@e6e31000 {
reg = <0 0xe6e31000 0 8>;
#pwm-cells = <2>;
@@ -1073,6 +1088,71 @@
};
};
+ thermal-zones {
+ sensor_thermal1: sensor-thermal1 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsc 0>;
+ sustainable-power = <3874>;
+
+ trips {
+ sensor1_crit: sensor1-crit {
+ temperature = <120000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ sensor_thermal2: sensor-thermal2 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsc 1>;
+ sustainable-power = <3874>;
+
+ trips {
+ sensor2_crit: sensor2-crit {
+ temperature = <120000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ sensor_thermal3: sensor-thermal3 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsc 2>;
+ sustainable-power = <3874>;
+
+ cooling-maps {
+ map0 {
+ trip = <&target>;
+ cooling-device = <&a57_0 2 4>;
+ contribution = <1024>;
+ };
+ map1 {
+ trip = <&target>;
+ cooling-device = <&a53_0 0 2>;
+ contribution = <1024>;
+ };
+ };
+ trips {
+ target: trip-point1 {
+ temperature = <100000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+
+ sensor3_crit: sensor3-crit {
+ temperature = <120000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH] arm64: dts: renesas: r8a77961: Add thermal nodes
@ 2020-03-06 11:00 ` Geert Uytterhoeven
0 siblings, 0 replies; 6+ messages in thread
From: Geert Uytterhoeven @ 2020-03-06 11:00 UTC (permalink / raw)
To: Magnus Damm, Niklas Söderlund
Cc: linux-renesas-soc, Geert Uytterhoeven, linux-arm-kernel, linux-pm
Add a device node for the Thermal Sensor/Chip Internal Voltage Monitor
in the R-Car M3-W+ (R8A77961) SoC, and describe the thermal zones.
According to the R-Car Gen3 Hardware Manual Errata for Revision 2.00 of
Jan 31, 2020, the thermal parameters for R-Car M3-W+ are the same as for
R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
It's a bit cold in Magnus' lab:
/ # grep . /sys/devices/virtual/thermal/thermal_zone?/temp
/sys/devices/virtual/thermal/thermal_zone0/temp:17000
/sys/devices/virtual/thermal/thermal_zone1/temp:19000
/sys/devices/virtual/thermal/thermal_zone2/temp:18000
---
arch/arm64/boot/dts/renesas/r8a77961.dtsi | 80 +++++++++++++++++++++++
1 file changed, 80 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
index b6915319a61c8bf0..2f016458f57d3a33 100644
--- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
@@ -474,6 +474,20 @@
#power-domain-cells = <1>;
};
+ tsc: thermal@e6198000 {
+ compatible = "renesas,r8a77961-thermal";
+ reg = <0 0xe6198000 0 0x100>,
+ <0 0xe61a0000 0 0x100>,
+ <0 0xe61a8000 0 0x100>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 522>;
+ power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
+ resets = <&cpg 522>;
+ #thermal-sensor-cells = <1>;
+ };
+
intc_ex: interrupt-controller@e61c0000 {
#interrupt-cells = <2>;
interrupt-controller;
@@ -785,6 +799,7 @@
status = "disabled";
};
+
pwm1: pwm@e6e31000 {
reg = <0 0xe6e31000 0 8>;
#pwm-cells = <2>;
@@ -1073,6 +1088,71 @@
};
};
+ thermal-zones {
+ sensor_thermal1: sensor-thermal1 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsc 0>;
+ sustainable-power = <3874>;
+
+ trips {
+ sensor1_crit: sensor1-crit {
+ temperature = <120000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ sensor_thermal2: sensor-thermal2 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsc 1>;
+ sustainable-power = <3874>;
+
+ trips {
+ sensor2_crit: sensor2-crit {
+ temperature = <120000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+
+ sensor_thermal3: sensor-thermal3 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsc 2>;
+ sustainable-power = <3874>;
+
+ cooling-maps {
+ map0 {
+ trip = <&target>;
+ cooling-device = <&a57_0 2 4>;
+ contribution = <1024>;
+ };
+ map1 {
+ trip = <&target>;
+ cooling-device = <&a53_0 0 2>;
+ contribution = <1024>;
+ };
+ };
+ trips {
+ target: trip-point1 {
+ temperature = <100000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+
+ sensor3_crit: sensor3-crit {
+ temperature = <120000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH] arm64: dts: renesas: r8a77961: Add thermal nodes
2020-03-06 11:00 ` Geert Uytterhoeven
@ 2020-03-08 16:35 ` Niklas Söderlund
-1 siblings, 0 replies; 6+ messages in thread
From: Niklas Söderlund @ 2020-03-08 16:35 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Magnus Damm, linux-arm-kernel, linux-renesas-soc, linux-pm
Hi Geert,
Thanks for your work.
On 2020-03-06 12:00:25 +0100, Geert Uytterhoeven wrote:
> Add a device node for the Thermal Sensor/Chip Internal Voltage Monitor
> in the R-Car M3-W+ (R8A77961) SoC, and describe the thermal zones.
>
> According to the R-Car Gen3 Hardware Manual Errata for Revision 2.00 of
> Jan 31, 2020, the thermal parameters for R-Car M3-W+ are the same as for
> R-Car M3-W.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> ---
> It's a bit cold in Magnus' lab:
>
> / # grep . /sys/devices/virtual/thermal/thermal_zone?/temp
> /sys/devices/virtual/thermal/thermal_zone0/temp:17000
> /sys/devices/virtual/thermal/thermal_zone1/temp:19000
> /sys/devices/virtual/thermal/thermal_zone2/temp:18000
> ---
> arch/arm64/boot/dts/renesas/r8a77961.dtsi | 80 +++++++++++++++++++++++
> 1 file changed, 80 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
> index b6915319a61c8bf0..2f016458f57d3a33 100644
> --- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
> +++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
> @@ -474,6 +474,20 @@
> #power-domain-cells = <1>;
> };
>
> + tsc: thermal@e6198000 {
> + compatible = "renesas,r8a77961-thermal";
> + reg = <0 0xe6198000 0 0x100>,
> + <0 0xe61a0000 0 0x100>,
> + <0 0xe61a8000 0 0x100>;
> + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cpg CPG_MOD 522>;
> + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
> + resets = <&cpg 522>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> intc_ex: interrupt-controller@e61c0000 {
> #interrupt-cells = <2>;
> interrupt-controller;
> @@ -785,6 +799,7 @@
> status = "disabled";
> };
>
> +
This don't looks like it's needed :-) With this fixed,
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
> pwm1: pwm@e6e31000 {
> reg = <0 0xe6e31000 0 8>;
> #pwm-cells = <2>;
> @@ -1073,6 +1088,71 @@
> };
> };
>
> + thermal-zones {
> + sensor_thermal1: sensor-thermal1 {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> + thermal-sensors = <&tsc 0>;
> + sustainable-power = <3874>;
> +
> + trips {
> + sensor1_crit: sensor1-crit {
> + temperature = <120000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + sensor_thermal2: sensor-thermal2 {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> + thermal-sensors = <&tsc 1>;
> + sustainable-power = <3874>;
> +
> + trips {
> + sensor2_crit: sensor2-crit {
> + temperature = <120000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + sensor_thermal3: sensor-thermal3 {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> + thermal-sensors = <&tsc 2>;
> + sustainable-power = <3874>;
> +
> + cooling-maps {
> + map0 {
> + trip = <&target>;
> + cooling-device = <&a57_0 2 4>;
> + contribution = <1024>;
> + };
> + map1 {
> + trip = <&target>;
> + cooling-device = <&a53_0 0 2>;
> + contribution = <1024>;
> + };
> + };
> + trips {
> + target: trip-point1 {
> + temperature = <100000>;
> + hysteresis = <1000>;
> + type = "passive";
> + };
> +
> + sensor3_crit: sensor3-crit {
> + temperature = <120000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +
> timer {
> compatible = "arm,armv8-timer";
> interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
> --
> 2.17.1
>
--
Regards,
Niklas Söderlund
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] arm64: dts: renesas: r8a77961: Add thermal nodes
@ 2020-03-08 16:35 ` Niklas Söderlund
0 siblings, 0 replies; 6+ messages in thread
From: Niklas Söderlund @ 2020-03-08 16:35 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: linux-renesas-soc, Magnus Damm, linux-arm-kernel, linux-pm
Hi Geert,
Thanks for your work.
On 2020-03-06 12:00:25 +0100, Geert Uytterhoeven wrote:
> Add a device node for the Thermal Sensor/Chip Internal Voltage Monitor
> in the R-Car M3-W+ (R8A77961) SoC, and describe the thermal zones.
>
> According to the R-Car Gen3 Hardware Manual Errata for Revision 2.00 of
> Jan 31, 2020, the thermal parameters for R-Car M3-W+ are the same as for
> R-Car M3-W.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> ---
> It's a bit cold in Magnus' lab:
>
> / # grep . /sys/devices/virtual/thermal/thermal_zone?/temp
> /sys/devices/virtual/thermal/thermal_zone0/temp:17000
> /sys/devices/virtual/thermal/thermal_zone1/temp:19000
> /sys/devices/virtual/thermal/thermal_zone2/temp:18000
> ---
> arch/arm64/boot/dts/renesas/r8a77961.dtsi | 80 +++++++++++++++++++++++
> 1 file changed, 80 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
> index b6915319a61c8bf0..2f016458f57d3a33 100644
> --- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
> +++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
> @@ -474,6 +474,20 @@
> #power-domain-cells = <1>;
> };
>
> + tsc: thermal@e6198000 {
> + compatible = "renesas,r8a77961-thermal";
> + reg = <0 0xe6198000 0 0x100>,
> + <0 0xe61a0000 0 0x100>,
> + <0 0xe61a8000 0 0x100>;
> + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cpg CPG_MOD 522>;
> + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
> + resets = <&cpg 522>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> intc_ex: interrupt-controller@e61c0000 {
> #interrupt-cells = <2>;
> interrupt-controller;
> @@ -785,6 +799,7 @@
> status = "disabled";
> };
>
> +
This don't looks like it's needed :-) With this fixed,
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
> pwm1: pwm@e6e31000 {
> reg = <0 0xe6e31000 0 8>;
> #pwm-cells = <2>;
> @@ -1073,6 +1088,71 @@
> };
> };
>
> + thermal-zones {
> + sensor_thermal1: sensor-thermal1 {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> + thermal-sensors = <&tsc 0>;
> + sustainable-power = <3874>;
> +
> + trips {
> + sensor1_crit: sensor1-crit {
> + temperature = <120000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + sensor_thermal2: sensor-thermal2 {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> + thermal-sensors = <&tsc 1>;
> + sustainable-power = <3874>;
> +
> + trips {
> + sensor2_crit: sensor2-crit {
> + temperature = <120000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + sensor_thermal3: sensor-thermal3 {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> + thermal-sensors = <&tsc 2>;
> + sustainable-power = <3874>;
> +
> + cooling-maps {
> + map0 {
> + trip = <&target>;
> + cooling-device = <&a57_0 2 4>;
> + contribution = <1024>;
> + };
> + map1 {
> + trip = <&target>;
> + cooling-device = <&a53_0 0 2>;
> + contribution = <1024>;
> + };
> + };
> + trips {
> + target: trip-point1 {
> + temperature = <100000>;
> + hysteresis = <1000>;
> + type = "passive";
> + };
> +
> + sensor3_crit: sensor3-crit {
> + temperature = <120000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +
> timer {
> compatible = "arm,armv8-timer";
> interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
> --
> 2.17.1
>
--
Regards,
Niklas Söderlund
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] arm64: dts: renesas: r8a77961: Add thermal nodes
2020-03-08 16:35 ` Niklas Söderlund
@ 2020-03-09 9:21 ` Geert Uytterhoeven
-1 siblings, 0 replies; 6+ messages in thread
From: Geert Uytterhoeven @ 2020-03-09 9:21 UTC (permalink / raw)
To: Niklas Söderlund
Cc: Geert Uytterhoeven, Magnus Damm, Linux ARM, Linux-Renesas, Linux PM list
Hi Niklas,
On Sun, Mar 8, 2020 at 5:35 PM Niklas Söderlund
<niklas.soderlund@ragnatech.se> wrote:
> On 2020-03-06 12:00:25 +0100, Geert Uytterhoeven wrote:
> > Add a device node for the Thermal Sensor/Chip Internal Voltage Monitor
> > in the R-Car M3-W+ (R8A77961) SoC, and describe the thermal zones.
> >
> > According to the R-Car Gen3 Hardware Manual Errata for Revision 2.00 of
> > Jan 31, 2020, the thermal parameters for R-Car M3-W+ are the same as for
> > R-Car M3-W.
> >
> > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> > --- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
> > +++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
> > @@ -785,6 +799,7 @@
> > status = "disabled";
> > };
> >
> > +
>
> This don't looks like it's needed :-) With this fixed,
>
> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Thanks, queued in renesas-devel for v5.7, with the above fixed.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] arm64: dts: renesas: r8a77961: Add thermal nodes
@ 2020-03-09 9:21 ` Geert Uytterhoeven
0 siblings, 0 replies; 6+ messages in thread
From: Geert Uytterhoeven @ 2020-03-09 9:21 UTC (permalink / raw)
To: Niklas Söderlund
Cc: Linux-Renesas, Magnus Damm, Linux ARM, Geert Uytterhoeven, Linux PM list
Hi Niklas,
On Sun, Mar 8, 2020 at 5:35 PM Niklas Söderlund
<niklas.soderlund@ragnatech.se> wrote:
> On 2020-03-06 12:00:25 +0100, Geert Uytterhoeven wrote:
> > Add a device node for the Thermal Sensor/Chip Internal Voltage Monitor
> > in the R-Car M3-W+ (R8A77961) SoC, and describe the thermal zones.
> >
> > According to the R-Car Gen3 Hardware Manual Errata for Revision 2.00 of
> > Jan 31, 2020, the thermal parameters for R-Car M3-W+ are the same as for
> > R-Car M3-W.
> >
> > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> > --- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
> > +++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
> > @@ -785,6 +799,7 @@
> > status = "disabled";
> > };
> >
> > +
>
> This don't looks like it's needed :-) With this fixed,
>
> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Thanks, queued in renesas-devel for v5.7, with the above fixed.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2020-03-09 9:21 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-06 11:00 [PATCH] arm64: dts: renesas: r8a77961: Add thermal nodes Geert Uytterhoeven
2020-03-06 11:00 ` Geert Uytterhoeven
2020-03-08 16:35 ` Niklas Söderlund
2020-03-08 16:35 ` Niklas Söderlund
2020-03-09 9:21 ` Geert Uytterhoeven
2020-03-09 9:21 ` Geert Uytterhoeven
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.